Download DMX TESTER

Transcript
15-
Please read these instructions carefully before use
User Manual
DMX TESTER
Cable Test
Backlight Mode
Power Manager
Unit Display
5.5
5.6
5.7
5.8
1-
Auto Fade Multi Mode
5.4.2
6. Battery
Auto Fade single Mode
DMX Out single Mode
5.3.1
5.4.1
DMX Out
5.3
DMX Out Multi Mode
DMX Address Remote Setting
5.2
Auto Fade
DMX In
5.1.2
5.4
Auto Setting
5.1.1
5.3.2
Manual Setting
5.1
1. Safety Instruction
2. Features
3. Technical Specification
4. Overview
5. How To Control The Unit
TABLE OF CONTENTS
3. 0 – 100%
5. To go back to the main functions please press the MENU button.
SETTING SAVE
LCD will display
change the batteries.
14-
setting available. If the battery is break down, please refer to the following diagram to
The fixture is using 4 sets AA NI-MH at least 1300mAh 1.2V (optional) and saving time
6. Battery
2. 00H – FFH
1. 000 – 255
UNIT TYPE IS
4. When you Press ENTER button, the unit will save the setting and
UNIT TYPE IS
UNIT TYPE IS
3. Press the MODE button to set the unit display
1. 000 – 255
UNIT TYPE IS
2. Press the ENTER button into the function and the LCD will display
For setting the unit on sleeping time.
MIN
000
MIN
13-
D OR H OR %
8. UNIT DISPLAY
1. Press MANU button up to LCD display
5.8 UNIT DISPLAY For setting the unit DMX level by different display type.
5. To go back to the main functions please press the MENU button.
SETTING SAVE
LCD will display.
4. When you Press ENTER button, the unit will save the setting and
010
SLEEPING TIME
3. Press the LEVEL RANGE button to set the sleeping time 0~10 min
TIME
SLEEPING
2. Press the ENTER button into the function and the LCD will display
7. POWER MANAGER
1. Press MANU button until the LCD display
5.7 POWER MANAGER
5. To go back to the main functions please press the MENU button.
SETTING SAVE
LCD will display
4. When you Press ENTER button, the unit will save the setting and
Never try to repair the unit by yourself. Repair by unqualified people could cause
¾
2-
¾ Do not try to dismantle or modify the unit.
¾ NEVER use the unit under the excessive humidity.
it with doubt and contact an authorized dealer.
¾ After removed the package, checking the unit is NOT damaged in any way. DON'T use
CAUTION!
damage. Contact your nearest dealer for service always.
Do not open the unit--there are not serviceable parts inside.
your local dealer for servicing.
Stop using the unit immediately in the event of serious operation problems and contact
¾
¾
Should any liquid be spilled on the unit, DISCONNECT the power supply to the unit
¾
immediately.
Avoid any flammable liquids, water or metal objects entering into the unit.
¾
WARNING!
consultation.
of operation, maintenance, and technical data. Keep this manual with the unit for future
Please read the unit manual carefully as it includes important information regarding details
1. Safety Instructions
2—2
1—X
Output Voltage:DC 9-12V 300 mA
¥ Weight:0.7 kg
¥ Dimension:140×101×51mm
3-
¥ Battery:AA NI-MH 1300mAh 1.2V (1300mAh at least, optional)
DMX connection:3-pin Male XLR-sockets
Control:DMX 512
ERROR
For setting the unit backlight whether is on or off.
OFF
BACKLIGHT
12-
3. Press the MODE button to set the backlight on or off
ON
BACKLIGHT
2. Press the ENTER button into the function and the LCD will display
6. BACKLIGHT MODE
1. Press MANU button until the LCD display
5.6 BACKLIGHT MODE
4. To go back to the main functions please press the MENU button.
There are 15 kinds of error state will be tested and display on the LCD.
2—X 3—X
CABLE
¥ DMX Input
3—3
If the signal cable is break down, the LCD will display
1-1
CABLE CORRECT
cable is good, the LCD will display
3. Plug the signal cable into the input and output socket, if the signal
It is mean the DMX tester no plug any signal cable.
2—X 3—X
ERROR
2. Press the ENTER button into the function and the LCD will display
Input Voltage:AC 120-240V ~ 50-60Hz
¥ Power supply
3. Technical Specification
mode for power saving.
Sleep function: When time surpass the internal setting time, it will enter into sleep
work for 3 hours or idling for 100 hours)
LCD backlight saving setting.
Built-in battery work for several hours continuously. (After charging for 5 hours, it could
¾
¾
1—X
Available for testing synchronized DMX in / out signal.
¾
¾
CABLE
3 types display:%, Hex and Binary.
¾
5. CABLE TEST
DMX output and input level test, and auto fade output.
¾
1. Press MANU button until the LCD display
For testing signal cable whether is good or breaks down.
DMX address set remotely
5.5 CABLE TEST
¾
2. Features
SP:000
TO:001
SP:009
TO:512
11-
8. To go back to the main functions please press the MENU button.
VA:100%
CH:001
7. Press LEVEL RANGE button to change the auto fade speed 0~9.
6. Press MODE button to switch to start channel and end channel.
channel.
5. Press ADDRESS/CHANNEL button to set start channel and end
VA:000%
CH:001
display.
4. Press ENTER button to make sure the select and the LCD will
MODE:MULTI
4. AUTO FADE
Please select Multi mode.
3. Press MODE button to select Single mode or Multi mode.
MODE:SINGLE
4. AUTO FADE
fast blink, and the LCD will display
2. Press the ENTER button into the function. The led of DMX OUT will
4. AUTO FADE
1. Press MANU button until the LCD display
5.4.2 Auto Fade Multi Mode
To change the address or channel
To change the DMX level range
DC 9~12V 300 mA Min.
Turns On/Off the power.
3. ENTER
4. ADDRESS/CHANNEL
5. LEVEL RANGE
6. DC INPUT
7. POWER
plug cable to link the fixture together.
To send DMX signal to DMX fixtures, use 3 pin Female XLR
4-
When you turn on the power switch, the LCD will display DMX TESTER Version 1.0
5. How To Operation The Unit
9. DMX OUT
cable to link the fixture together.
To receive DMX fixtures signal input, use 3 pin Male XLR plug
To make sure or save the setting
2. MODE
8. DMX IN
To select the main functions
To change the mode
1. MENU
4. Overview
5-
8. To go back to the main functions please press the MENU button.
SP:009
10-
7. To go back to the main functions please press the MENU button.
VA:100%
button to change the other channels auto fade speed.
PLEASE WAIT…
fast blink.
SP:003
6. Please use ADDRESS/CHANNEL button and LEVEL RANGE
VA:000%
CH:001
CH:005
7. When auto setting DMX fixtures finished, the led of DMX OUT will
SP:000
press LEVEL RANGE button to change the auto fade speed 0~9.
SCAN FIXTURE
start address remotely and LCD will display
6. When you press ENTER button, the unit will auto set DMX fixtures
address 0~512
5. Press the ADDRESS/CHANNEL button to set the DMX start
VA:000%
ADDRESS:001
5. Press ADDRESS/CHANNEL button to select channel 0~512, and
CH:001
display
SET DMX START
display
4. Press ENTER button to make sure the select and the LCD will
MODE:SINGLE
MODE:AUTO
4. Press ENTER button to make sure the select and the LCD will
4. AUTO FADE
Please select Single mode.
3. Press MODE button to select Single mode or Multi mode.
MODE:SINGLE
4. AUTO FADE
fast blink, and the LCD will display
2. Press the ENTER button into the function. The led of DMX OUT will
4. AUTO FADE
1. Press MANU button until the LCD display
5.4.1 Auto Fade on Single Mode
5.4 AUTO FADE
DMX ADDRESS
Please select Auto mode for DMX address auto remote setting
3. Press MODE button to select Auto or Manual mode.
MODE:AUTO
DMX ADDRESS
2. Press the ENTER button into the function and the LCD will display
REMOTE SETTING
1. DMX ADDRESS
1. Press MANU button until the LCD display
5.1.1 Auto mode (only for Acme LED MOOD series lightings)
No need to climb up to the ceiling to change light’s address.
5.1 DMX Address Remote Setting You can set up DMX address remotely by the unit.
TO:001
TO: 008
9-
8. To go back to the main functions please press the MENU button.
VA: 100%
CH: 001
0~255.
7. Press LEVEL RANGE button to change the DMX level range
6. Press MODE button to switch to start channel and end channel.
channel.
5. Press ADDRESS/CHANNEL button to set start channel and end
VA: 000%
CH: 001
display
6-
9. To go back to the main functions please press the MENU button.
start address.
button and ADDRESS/CHANNEL button to set next fixture DMX
8. Press ENTER button to save the setting, and use LEVEL RANGE
fast blink.
7. When auto setting of DMX fixtures finished, the led of DMX OUT will
ADDRESS: xxx
FIXTURE : 001
ADDRESS/CHANNEL button to set the DMX start address 0~512
6. Press LEVEL RANGE button to select fixture 0~170, and press
5. When scan fixtures finished, the first fixture will light on.
PLEASE WAIT…
SCAN FIXTURE
display
4. Press ENTER button to make sure the select and the LCD will
MODE:MANUAL
4. Press ENTER button to make sure the select and the LCD will
DMX ADDRESS
MODE:MULTI
Please select Manual mode for DMX address auto remote setting
3. Press MODE button to select Auto or Manual mode.
MODE:AUTO
DMX ADDRESS
2. Press the ENTER button into the function and the LCD will display
REMOTE SETTING
1. DMX ADDRESS
1. Press MANU button until the LCD display
5.1.2 Manual Mode (only for Acme i Solution series and LED MOOD series lightings)
3. DMX OUT
Please select Multi mode.
3. Press MODE button to select Single mode or Multi mode.
MODE:SINGLE
3. DMX OUT
fast blink, and the LCD will display
2. Press the ENTER button into the function. The led of DMX OUT will
3. DMX OUT
1. Press MANU button until the LCD display
5.3.2 DMX Out Multi mode
7-
4. To go back to the main functions please press the MENU button.
242 255 016 255
005 006 007 008
DMX 512 level range of the DMX link.
3. Press the ADDRESS/CHANNEL button to display next 4 channels
128 240 000 255
001 002 003 004
first 4 channels DMX 512 level range of the DMX link.
2. Press the ENTER button into the function and the LCD will display
NO DMX SIGNAL IN
If the unit didn’t connecting any fixtures the LCD will display
2. DMX IN
1. Press MANU button until the LCD display
5.2 DMX IN The unit can receive DMX signal to test whether the signal is correct or error.
8-
7. To go back to the main functions please press the MENU button.
VA: 100%
CH: 005
button to change the other channels DMX level range.
6. Please use ADDRESS/CHANNEL button and LEVEL RANGE
VA: 050%
CH: 004
press LEVEL RANGE button to change the DMX level range 0~255.
5. Press ADDRESS/CHANNEL button to select channel 0~512, and
VA: 000%
CH: 001
display
4. Press ENTER button to make sure the select and the LCD will
MODE:SINGLE
3. DMX OUT
Please select Single mode.
3. Press MODE button to select Single mode or Multi mode.
MODE:SINGLE
3. DMX OUT
fast blink, and the LCD will display
2. Press the ENTER button into the function. The led of DMX OUT will
3. DMX OUT
1. Press MANU button until the LCD display
5.3.1 DMX Out Single mode
5.3 DMX OUT