Download QTFX-F1/F2 Flame Effect User Manual
Transcript
QTFX-F1/F2 Flame Effect User Manual 160.470UK & 160.471UK 1 User Manual – QTFX-F1/F2 160.470/1UK QTFX-F1/F2 Flame Effect – For indoor use only User Manual – QTFX-F1/F2 15. Technical specification : QTFX-F1 Caution! Please read this manual carefully before is not covered by the warranty! QTFX-F2 230Vac, 50Hz Power supply operating! Damage caused by misuse 1. 160.470/1UK Fuse F5A Power consumption 60W General Introduction : Light Source Really heat up your party with this mesmerising flame effect. Reaching up DMX Channels to a height of 1.5m, the silk flame flutters in the air whilst lit up with a Max flame height combination of 10mmØ LEDs, giving the appearance of a hot flame. It is Dimensions low maintenance and quick to set up, making it perfect for event and hire 36 x 10mmØ (R:32, B:4) (36 x 10mmØ (R:12, G:12, B:12) N/A 6 1.5m 530 x 230 x 360mm 12kg Weight companies or as a permanent fixture on stage. Features : 13. Disposal : Reaches up to a height of 1.5m Red and blue 10mmØ LED (QTFX-F1) Please disposal of the unserviceable device according to the current RGB Colour mixing (QTFX-F2) statutory requirement High speed fans Replacement silk flames available (Ref: 160.472UK) Copyright protected by QTX Light Ltd 2 11 User Manual – QTFX-F1/F2 160.470/1UK 14. DMX Operation for QTFX-F2: DMX Channel User Manual – QTFX-F1/F2 2. 160.470/1UK Package Contents : Please check the contents to ensure that the product has been received in DMX good condition. Value Function 1 000-255 Red Colour 0-100% Dimming 2 000-255 Green Colour 0-100% Dimming QTFX-Flame 3 000-255 Blue Colour 0-100% Dimming effect x 1pcs 4 000-255 RGB Colour change 5 000-255 Strobe Slow to Fast If you find any accessory is missing or the machine has arrived with any Overall Dimmer problems, please contact your local dealer at once. Do not try to fix this 6 000-255 User’s Guide x 1pcs Power Cord x 1pcs item yourself or you will lose the warranty. Please keep the original package and invoice for any possible replacement or returned demand. 3. Setup : 1. Unpack the Flame machine and place in a safe location where it will not be tampered with. 2. Unwrap the silk flame and place in to the slot between the LEDs. 3. Plug in the supplied IEC power lead. 4. Turn the power switch on and the LEDs will light up, fans will start to blow and the silk flame will start to rise. 5. For the QTFX-F2 model read section 13 about the digital controls and DMX options. 10 3 User Manual – QTFX-F1/F2 160.470/1UK 5. Installation advice : User Manual – QTFX-F1/F2 160.470/1UK 13. Operation for QTFX-F2: The fixture may be placed anywhere on a stage or in a display providing nothing obstructs the front of the machine, fan or vents pathway. Never install in places where the fixture will be exposed to rain, high humidity, extreme temperatures changes or restricted ventilation. 6. Caution! To prevent Mortal Electrical Risk and Long Life Operation : LED Display For your safety, please kindly pay attention to all of the warnings listed ADDR below: Always plug in the power plug last and disconnect from the mains SHnD when the device is not in use or before cleaning. Do not install and operate the device in rain or extreme heat, moisture or dusty environments. CHND This device is for indoor use only and in a dry environment. Do not switch on immediately but wait until it reaches to room temperature if the device has been exposed to drastic temperature SLND fluctuations. Do not shake the device and avoid brute force when installing or operating LED Do not use the device during thunderstorms and please disconnect Secondary Display Action A001 - A512 Set DMX Address SOUn Sound to light mode COLr Colour change FAdE Slow colour changing pattern AUTO Auto mode. The colou automatically 1 Ch DMX Mode single channel 6 Ch DMX mode 6 channel SL 1 Slave mode 1 SL 2 Slave mode 2 N OFF Master offf NAST Master mode ON Turn the LEDs ON/OFF OFF the power. Do not use solvents or aggressive detergent to clean the device. Use LDSP On LED Display on/off Off a soft and clean cloth. red Do not modify the device or the connected power cord without BALA authorisation. Manual Mode for setting one static GrEEn colour Blue 4 9 User Manual – QTFX-F1/F2 160.470/1UK 12. QTFX-F2 Layout: User Manual – QTFX-F1/F2 160.470/1UK 7. Connect with power supply - The ground wire must be connected : Use the plug to connect to the main power supply as following. Wire Connection International signal Brown Live L Blue Neutral N Yellow /Green Earth 8. Quick Trouble Shooting : If the unit is not functioning properly 8.1 Check if main power is on and fuse hasn’t blown 8.2 The remote control is plugged in correctly in to the socket 8.3 Check there is fluid in the tank 8.4 Check that the pipe is pushed down to the bottom of the tank 8.5 Check the correct fluid has been used. 1. DMX DIP Switch addresses 2. DMX IN 3. DMX OUT 4. POWER ON/OFF 5. IEC POWER IN 8 5 User Manual – QTFX-F1/F2 160.470/1UK 9. Replacing Fuse : User Manual – QTFX-F1/F2 160.470/1UK 11. QTFX-F1 Layout: Disconnect from the main power supply first, then remove the fuse holder above the IEC Socket to reveal the fuse. Replace the correct fuse rating as stated on lighting or user guide. Then, lock the fuse holder cover back into place. 10. General Maintenance : To maintain optimum performance and minimize wear, the item should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned after use to avoid dust build-up and blockages, which can result in poor performances, overheating and breakages. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components. Clean the external case when the fixture is cold with a dry cloth or tissue, and drag dirt and grime to the outside case. 6 1. Power ON/OFF 2. IEC Power IN/OUT 7