Download NuTiny-SDK-M0518 Series User Manual

NuTiny-SDK-M0518 Series User Manual
NuTiny-SDK-M0518SD2AE
User Manual
The information described in this document is the exclusive intellectual property of
Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton.
Nuvoton is providing this document only for reference purposes of NuMicro™ microcontroller based system design.
Nuvoton assumes no responsibility for errors or omissions.
All data and specifications are subject to change without notice.
For additional information or questions, please contact: Nuvoton Technology Corporation.
Des. 24, 2014
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
Table of Contents
1
Overview ........................................................................................... 3
2
Introduction to NuTiny-SDK- M0518SD2AE ............................................ 4
2.1
2.2
2.3
NuTiny-SDK- M0518SD2AE Jumper Description .............................................5
Pin Assignment for Extended Connectors ......................................................6
NuTiny-SDK- M0518SD2AE PCB Placement ...................................................8
Starting to Use NuTiny-SDK- M0518SD2AE on the Keil μVision® IDE ......... 9
3
3.1
3.2
3.3
3.4
Downloading and Installing Keil μVision® IDE Software ...................................9
Downloading and Installing Nuvoton Nu-Link Driver .......................................9
Hardware Setup .........................................................................................9
Example Program..................................................................................... 10
4
Starting to Use NuTiny-SDK- M0518SD2AE on the IAR Embedded
Workbench ............................................................................................. 11
4.1
4.2
4.3
4.4
5
NuTiny-SDK- M0518SD2AE Schematics ............................................... 13
5.1
5.2
5.3
6
NuTiny-EVB- M0518SD2AE Schematic ........................................................ 13
NuTiny-EVB- M0518SD2AE Schematic ........................................................ 14
Nu-Link-Me Schematic .............................................................................. 15
Downloading NuMicro™ Related Files from Nuvoton Website .................. 16
6.1
6.2
6.3
7
Downloading and Installing IAR Embedded Workbench Software .................... 11
Downloading and Installing Nuvoton Nu-Link Driver ..................................... 11
Hardware Setup ....................................................................................... 11
Example Program..................................................................................... 12
Downloading NuMicro™ Keil μVision® IDE Driver .......................................... 16
Downloading NuMicro™ IAR EWARM Driver ................................................. 18
Downloading NuMicro™ M0518SD2AE Series BSP Software Library ................ 20
Revision History ............................................................................... 22
Des. 24, 2014
2 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
1 Overview
The NuTiny-SDK- M0518SD2AE is a specific development tool for NuMicro™ M0518
series by which users can develop and verify the application program easily. The
NuTiny-SDK-M0518SD2AE includes two portions: NuTiny-EVB-M0518SD2AE (an
evaluation board) and Nu-Link-Me (Debug Adaptor). With the NuTiny-SDKM0518SD2AE, users do not need additional ICE or debug equipment.
Des. 24, 2014
3 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
2 Introduction to NuTiny-SDK- M0518SD2AE
The following figure shows the NuTiny-SDK- M0518SD2AE for M0518SD2AE series, in
which the left portion is called NuTiny-EVB- M0518SD2AE and the right portion is
Debug Adaptor called Nu-Link-Me.
The NuTiny-EVB- M0518SD2AE is similar to other development board. Users can use
it to develop and verify applications to emulate the real behavior. In fact, the real chip
M0518SD2AE is mounted on the board. The NuTiny-EVB- M0518SD2AE can be a real
system controller to design user target system.
The Nu-Link-Me is a Debug Adaptor which connects the USB port of your PC to your
target system (via Serial Wired Debug Port) and allows you to program and debug
embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor
with Keil or IAR, please refer to “Nuvoton NuMicro™ IAR ICE Driver User Manual” or
Nuvoton NuMicro™ Keil ICE Driver User Manual” for details.
VDD
(JP1)
LQFP-64 pin
Extended Connector
(JP7, JP6)
VSS
(JP2)
LQFP-64 pin
Extended Connector
(JP4, JP5)
ICE Controller
USB Connector
(ICEJ2)
Reset Key
(SW1)
Power LED
I/O LED
Target Chip
ICE Controller
VCC：3.3V or 5V
(JP8)
Figure 2-1 NuTiny-SDK- M0518SD2AE (Green PCB Board)
Des. 24, 2014
4 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
2.1
NuTiny-SDK- M0518SD2AE Jumper Description
2.1.1 Power Settings
 JP1: VDD Voltage connecter in NuTiny-EVB- M0518SD2AE
 J1: USB port in Nu-Link-Me
Model
Model 1
JPR1
Select VCC33
(default)
Model 2
X
J1 USB port
JP1 VDD
MCU Voltage
Connect to PC
DC 3.3V output
DC 3.3V
X
DC 2.5 V ~ 5.5 V
Input
Voltage by JP1
input
X: Unused.
2.1.2 Debug Connectors
 JP3: Connector in target board (NuTiny-EVB- M0518SD2AE) for connecting with
Nuvoton ICE adaptor (Nu-Link-Me)
 JP8: Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board
(e.g. NuTiny-EVB- M0518SD2AE)
2.1.3 USB Connectors
 J1: Mini USB Connector in Nu-Link-Me connected to a PC USB port
2.1.4 Extended Connectors
 JP4, JP5, JP6 and JP7: Show all chip pins in NuTiny-EVB- M0518SD2AE
2.1.5 Buttons
 SW1: Reset button in NuTiny-EVB- M0518SD2AE
2.1.6 Power Connectors
 JP1: VDD connector in NuTiny-EVB- M0518SD2AE
 JP2: VSS connector in NuTiny-EVB- M0518SD2AE
Des. 24, 2014
5 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
2.2
Pin Assignment for Extended Connectors
The NuTiny-EVB- M0518SD2AE provides the M0518SD2AE target chip on board and
the extended connectors (JP4, JP5, JP6 and JP7) for LQFP48-pin. The following
table is the pin assignment for M0518SD2AE.
Pin No
01
02
10
11
Pin Name
PB.14,INT0
PB.13
PB.12,CLKO,BPWM1_CH
3
PF.5,I2C0_SCL,PWM1_C
H5
PF.4,I2C0_SDA,PWM1_C
H4
PA.11,I2C1_SCL,PWM1_
CH3
PA.10,I2C1_SDA,PWM1_
CH2
PA.9,I2C0_SCL,UART1_n
CTS
PA.8,I2C0_SDA,UART1_n
RTS
PB.4,UART1_RXD
PB.5,UART1_TXD
12
PB.6,UART1_nRTS
44
13
PB.7,UART1_nCTS
45
14
LDO_CAP
46
15
VDD
47
16
17
18
VSS
PB.0,UART0_RXD
PB.1,UART0_TXD
PB.2,UART0_nRTS,TM2_
EXT,TM2,PWM1_BRAKE1
PB.3,UART0_nCTS,TM3_
EXT,TM3,PWM1_BRAKE0
PD.6,BPWM1_CH1
48
49
50
PF.6,ICE_CLK
AVSS
PA.0,PWM0_CH4,ADC0,I2C1
_SCL,UART5_TXD
PA.1,PWM0_CH5,ADC1,I2C1
_SDA,UART5_RXD
PA.2,PWM1_CH0,ADC2,UAR
T3_TXD
PA.3,PWM1_CH1,ADC3,UAR
T3_RXD
PA.4,ADC4
PA.5,UART3_RXD,ADC5
PA.6,UART3_TXD,ADC6
51
PA.7,Vref,ADC7
52
AVDD
53
PC.7,PWM0_BRAKE1,I2C0_S
03
04
05
06
07
08
09
19
20
21
Des. 24, 2014
Pin No
33
34
Pin Name
PC.11,PWM1_BRAKE1
PC.10,PWM1_BRAKE0
35
PC.9,PWM0_BRAKE1
36
PC.8,PWM0_BRAKE0
37
PA.15,PWM0_CH3
38
PA.14,PWM0_CH2
39
40
PA.13,PWM0_CH1,UART5_T
XD
PA.12,PWM0_CH0,UART5_R
XD
41
PF.7,ICE_DAT
42
43
6 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
22
23
24
25
26
27
28
29
30
31
32
Des. 24, 2014
PD.7,BPWM1_CH0
PD.14,BPWM0_CH5,UAR
T2_RXD
PD.15,BPWM0_CH4,UAR
T2_TXD
PC.3,BPWM0_CH3,SPI0_
MOSI0
PC.2,BPWM0_CH2,SPI0_
MISO0
PC.1,BPWM0_CH1,SPI0_
CLK
PC.0,BPWM0_CH0,SPI0_
SS0
PE.5,PWM0_CH5,TM1_E
XT,TM1
PB.11,TM3,PWM0_CH4
PB.10,TM2
54
CL,UART4_RXD
PC.6,PWM0_BRAKE0,I2C0_S
DA,UART4_TXD
55
PC.15
56
PC.14
57
PB.15, ,BPWM1_CH5TM0,TM
0_EXT,INT1
58
PF.0,XT1_OUT
59
PF.1,XT1_IN
60
nRESET
61
VSS
62
63
VDD
PF.8, PWM1_CH4,CLKO
PB.8,BPWM1_CH2,CLKO,TM
PB.9,TM1
64
0,STADC
Table 2-1 Pin Assignment for M0518SD2AE
7 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
2.3
NuTiny-SDK- M0518SD2AE PCB Placement
The following figure shows the NuTiny-SDK- M0518SD2AE PCB placement.
Figure 2-2 NuTiny-SDK- M0518SD2AE PCB Placement
Des. 24, 2014
8 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
3 Starting to Use NuTiny-SDK- M0518SD2AE on the Keil μVision® IDE
3.1
Downloading and Installing Keil μVision® IDE Software
Please connect to the Keil company website (http://www.keil.com) to download the
Keil μVision® IDE and install the RVMDK.
3.2
Downloading and Installing Nuvoton Nu-Link Driver
Please connect to Nuvoton NuMicro™ website (http://www.nuvoton.com/NuMicro) to
download the “NuMicro™ Keil μVision® IDE driver” file. Please refer to section 6.1 for
the detailed download flow. After the Nu-Link driver is downloaded, please unzip the
file and execute the “Nu-Link_Keil_Driver.exe” to install the driver.
3.3
Hardware Setup
The hardware setup is shown in the following figure.
Figure 3-1 NuTiny-SDK- M0518SD2AE Hardware Setup
Des. 24, 2014
9 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
3.4
Example Program
This example demonstrates how to download and debug an application on a NuTinySDK- M0518SD2AE board.
The example file can be found in the directory list shown in the following figure.
Directory
Figure 3-2 Example Directory
To use this example:
The I/O LED on the NuTiny-EVB- M0518SD2AE board will turn on.




Start μVision®
Project – Open
Open the SYS.uvproj project file

Start Debug mode
When using the debugger commands, you
may:

Review variables in the watch
window

Single step through code

Reset the device

Run the application
Project – Build
Compile and link the SYS application
Flash – Download
Program the application code into on-chip
Flash ROM
Des. 24, 2014
10 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
4 Starting to Use NuTiny-SDK- M0518SD2AE on the IAR Embedded
Workbench
4.1
Downloading and Installing IAR Embedded Workbench Software
Please connect to IAR company website (http://www.iar.com) to download the IAR
Embedded Workbench and install the EWARM.
4.2
Downloading and Installing Nuvoton Nu-Link Driver
Please
connect
to
Nuvoton
Company
NuMicro™
website
(http://www.nuvoton.com/NuMicro) to download “NuMicro™ IAR EWARM Driver” file.
Please refer to section 6.2 for the detail download flow. After the Nu-Link driver is
downloaded, please unzip the file and execute the “Nu-Link_IAR_Driver.exe” to install
the driver.
4.3
Hardware Setup
The hardware setup is shown in the following figure.
Figure 4-1 NuTiny-SDK- M0518SD2AE Hardware Setup
Des. 24, 2014
11 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
4.4
Example Program
This example demonstrates how to download and debug an application on a NuTinySDK- M0518SD2AE board.
The example file can be found in the directory list shown in the following figure.
Directory
Figure 4-2 Example Directory
To use this example:
The I/O LED on the NuTiny-EVB- M0518SD2AE board will turn on.



Start IAR Embedded Workbench
File-Open-Workspace
Open the SYS.eww workspace file
Project - Make
Compile and link the SYS application
Des. 24, 2014

Project – Download and Debug
Program the application code into on-chip
Flash ROM

Single step through code

Reset the device

Run the application
12 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
5 NuTiny-SDK- M0518SD2AE Schematics
NuTiny-EVB- M0518SD2AE Schematic
5.1
Off-page Connector
ADAVSS
ICE_CLK
ICE_DAT
P[1:64]
D12MO
D12MO
P48
P47
P46
P45
P44
P43
P42
P41
P40
P39
P38
P37
P36
P35
P34
P33
D12MI
D12MI
VCC5
DAVDD
CB5
0.1u
C0603
D12MO
D12MI
RESET
DVCC5
CB3
0.1u
C0603
P49
P50
P51
P52
P53
P54
P55
P56
P57
P58
P59
P60
P61
P62
P63
P64
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
PA.5/UART3_RXD/ADC5
PA.6/UART3_TXD/ADC6
PA.7/Vref /ADC7
AVDD
PC.7/PWM0_BRAKE1/I2C0_SCL/UART4_RXD
PC.6/PWM0_BRAKE0/I2C0_SDA/UART4_TXD
PC.15
PC.14
PB.15/BPWM1_CH5/TM0/TM0_EXT/INT1
PF.0/XT1_OUT
PF.1/XT1_IN
nRESET
VSS
VDD
PF.8/PWM1_CH4/CLKO
PB.8/BPWM1_CH2/CLKO/TM0/STADC
TM1/PB.9
TM2/PB.10
TM3/PWM0_CH4/PB.11
TM1_EXT/TM1/PWM0_CH5/PE.5
SPI0_SS0/BPWM0_CH0/PC.0
SPI0_CLK/BPWM0_CH1/PC.1
SPI0_MISO0/BPWM0_CH2/PC.2
SPI0_MOSI0/BPWM0_CH3/PC.3
UART2_TXD/BPWM0_CH4/PD.15
UART2_RXD/BPWM0_CH5/PD.14
BPWM1_CH0/PD.7
BPWM1_CH1/PD.6
UART0_nCTS/TM3_EXT/TM3/PWM1_BRAKE0/PB.3
UART0_nRTS/TM2_EXT/TM2/PWM1_BRAKE1/PB.2
UART0_TXD/PB.1
UART0_RXD/PB.0
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
P32
P31
P30
P29
P28
P27
P26
P25
P24
P23
P22
P21
P20
P19
P18
P17
PB.14/INT0
PB.13
PB.12/CLKO/BPWM1_CH3
PF.5/I2C0_SCL/PWM1_CH5
PF.4/I2C0_SDA/PWM1_CH4
PA.11/I2C1_SCL/PWM1_CH3
PA.10/I2C1_SDA/PWM1_CH2
PA.9/I2C0_SCL/UART1_nCTS
PA.8/I2C0_SDA/UART1_nRTS
PB.4/UART1_RXD
PB.5/UART1_TXD
PB.6/UART1_nRTS
PB.7/UART1_nCTS
LDO_CAP
VDD
VSS
R8
0
GND
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
M0518SD2AE_LQFP64
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
2
1
JP11
VCC
GND
ADC4/PA.4
ADC3/PWM1_CH1/UART3_RXD/PA.3
ADC2/PWM1_CH0/UART3_TXD/PA.2
ADC1/PWM0_CH5/I2C1_SDA/UART5_RXD/PA.1
ADC0/PWM0_CH4/I2C1_SCL/UART5_TXD/PA.0
AVSS
ICE_CLK/PF.6
ICE_DAT/PF.7
PWM0_CH0/UART5_RXD/PA.12
PWM0_CH1/UART5_TXD/PA.13
PWM0_CH2/PA.14
PWM0_CH3/PA.15
PWM0_BRAKE0/PC.8
PWM0_BRAKE1/PC.9
PWM1_BRAKE0/PC.10
PWM1_BRAKE1/PC.11
U2
P[1:64]
DVCC5
CT2
1uF/6.3V
TANT-A
CB4
0.1u
C0603
Title
NUTINY -SDK-M0518
Size
Document Number
Custom<Doc>
Date:
Des. 24, 2014
13 of 21
Thursday , December 25, 2014
Rev
<Rev Code>
Sheet
3
of
3
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
NuTiny-EVB- M0518SD2AE Schematic
5.2
DVCC5
VCC5
R1
10K
R0603
SW1
PUSH BOTTOM
SW
DVCC5
JP1
DAVDD
NC
RESET
L0603
1
2
Reset
TANT-A
L1
P[1:64]
L2
JP2
C1
10uF/10V
Off-page Connector
DVCC5
1
2
ICERST
D12MO
L0603
ADAVSS
NC
D12MI
P[1:64]
D12MO
D12MI
Power
DVCC5
JP3
1
3
5
7
9
2
4
6
8
10
ICEDAT
ICECLK
ICERST
NC
VCC5
ICE INTERFACE
GND
TICEDVDD5
TICEDAT
TICECLK
TICERST
C2
20p
D12MO
C0603
C3
20p
VCC
GND
TICEDVDD5
TICEDAT ICEDAT
TICECLK ICECLK
TICERST ICERST
VCC5
X1
12MHz
VCC
XTAL3-1
GND
P1
P3
P5
P7
P9
P11
P13
P15
D12MI
C0603
DVCC5
2
P33
P35
P37
P39
P41
P43
P45
P47
R2
1 0805
2
POWER1
Green
1 0805
P17
P19
P21
P23
P25
P27
P29
P31
JP5
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
P18
P20
P22
P24
P26
P28
P30
P32
NC
JP6
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
P34
P36
P38
P40
P42
P44
P46
P48
P49
P51
P53
P55
P57
P59
P61
P63
JP7
1
3
5
7
9
11
13
15
2
4
6
8
10
12
14
16
P50
P52
P54
P56
P58
P60
P62
P64
NC
IO
PR1
LED
P2
P4
P6
P8
P10
P12
P14
P16
NC
510
R0603
N2
2
4
6
8
10
12
14
16
connect
DVCC5
P2
1
3
5
7
9
11
13
15
NC
Crystal
IO1
Red
JP4
510
R0603
N1
Title
NUTINY-SDK-M0518
Size
Document Number
Custom
Date:
Des. 24, 2014
14 of 21
Wednesday , September 17, 2014 Sheet
Rev
1.0
of
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
5.3
Nu-Link-Me Schematic
VCC5
VCC5
R3
10K
R0603
VCC5
ISPLED 2
ICP1
Y ellow
1 0805
NUC_RST#
RP1
1 8P4R-330 2
3
4
5
6
7
8
NUC_RST#
12M_I
12M_O
ICE1
Red
PVSS
8P4RA
2
GND
1 0805
C4
10uF/10V
GREEN 2
BUSY 1
Green
1 0805
U1
ICELED
ISPLED
RED
GREEN
VCC5
CB1
0.1u
C0603
AVDD
INT0/PB14
CPO1/PB13
CPO0/PB12
X32I
X32O
I2C1SCL/PA11
I2C1SDA/PA10
I2C0SCL/PA9
I2C0SDA/PA8
RX1/PB4
TX1/PB5
RTS1/PB6
CTS1/PB7
LDO
VDD
VSS
VCC5
N3
R5
NC
R0603
C0603
X2
12MHz
XTAL3-1 C6
20p
12M_I
PA4/ADC4
PA3/ADC3
PA2/ADC2
PA1/ADC1
PA0/ADC0
AVSS
ICE_CK
ICE_DAT
PA12/PWM0
PA13/PWM1
PA14/PWM2
PA15/PWM3
PC8/SS10
PC9/SPCLK1
PC10/SDI10
PC11/SDO10
NUC12SRE3AN
C0603
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
VCC5
ICE_CLK
ICE_DAT
RTCK1
100K
R0603
ADAVSS
TICERST
TICECLK
RTDA3
RTDA2
RTDA1
100K
R0603
RRSET1
100K
R0603
TICEDAT
TICERST
0 33
R0603
R0603
VCC5
VCC5
VCC5
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
L3
L0603
2
4
6
8
10
C5
20p
R4
33
R0603
VBUS
VDD33
DD+
PB0/RX0
PB1/TX0
PB2/RTS0
PB3/CTS0
PC3/SDO00
PC2/SDI00
PC1/SPCLK0
PC0/SS00
PE5
PB11/TM3
PB10/SS01/TM2
PB9/SS11/TM1
CT1
1uF/6.3V
TANT-R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
3
5
7
9
TICEDAT
TICECLK
TICERST
NC
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
IDLE1
Red
1 0805
SS24A
RB060L
TANT-A
AVDD
STADC/TM0/PB8
PVSS
VDD1
VSS1
/RESET
XT1_In
XT1_Out
INT1/PB15
CPP1/PC14
CPN1/PC15
CPP0/PC6
CPN0/PC7
AVDD
ADC7/PA7
ADC6/PA6
ADC/PA5
2
D1
JP8
TICEVCC
TICEDAT
TICECLK
TICERST
ICE_RST
12M_O
RED
1
VCC
ICELED 2
VCC5
ICE CONNECT IF
VCC5
VBUS
USB_D+
USB_D-
L4
L0603
ADAVSS
USBVBUS
R6
100
R0603
USBVBUS
C7
1u
C0603
CB2
0.1u
C0603
R7
100
R0603
DM
DP
J1
mini USB 5pin
1
2
3
4
5
VCC
DM
DP
NC
GND
SHIELD
SHIELD
SHIELD
SHIELD
USB_MINI_B
VCC5
RTIDA1
100K
R0603
NC
6
7
8
9
1
2
3
4
5
L5
ICE_DAT
ICE_CLK
ICE_RST
RICK1
100K
R0603
DEBUG
JP9
L0805
P5V
OUT
3
2
1
CP1
10uF/10V
TANT-A
JPR1
HEADER 3
P3V
USBVBUS
DM
DP
4
3
1
2
PD1
USBVBUS SS24A
1
2
IN
GND
OUT
UP1
AMS1117_3.3v
RB060L
JP10
1
2
3
4
Title
Rev
1.0
NC
Date:
Des. 24, 2014
NuLink-Me
Size
Document Number
Custom
15 of 21
Thursday , December 04, 2014
Sheet
of
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
6
Downloading NuMicro™ Related Files from Nuvoton Website
6.1
Step1
Downloading NuMicro™ Keil μVision® IDE Driver
™
Visit the Nuvoton NuMicro website: http://www.nuvoton.com/NuMicro.
2-1. Move to “Support”
2-2. Click here to enter
Tool & Software
Step2
Des. 24, 2014
16 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
Click here to enter
Software
download page
Step3
Click here to
download
the file.
Step4
Step5
™
®
Download the NuMicro Keil μVision IDE driver.
Des. 24, 2014
17 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
6.2
Step1
Downloading NuMicro™ IAR EWARM Driver
™
Visit the Nuvoton NuMicro website: http://www.nuvoton.com/NuMicro.
2-1. Move to “Support”
2-2. Click here to enter
Tool & Software
Step2
Des. 24, 2014
18 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
Click here to enter
Software
download page
Step3
Step4
Step5
Click here to
download
the file.
™
Download the NuMicro IAR EWARM driver.
Des. 24, 2014
19 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
6.3
Step1
Downloading NuMicro™ M0518SD2AE Series BSP Software Library
™
Visit the Nuvoton NuMicro website: http://www.nuvoton.com/NuMicro.
2-1. Move to “Support”
2-2. Click here to enter
Tool & Software
Step2
Des. 24, 2014
20 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
Click here to enter
Software
download page
Step3
Step4
™
Download the NuMicro M0518 Series CMSIS BSP.
Des. 24, 2014
21 of 21
Rev. 1.00
NuTiny-SDK-M0518 Series User Manual
7 Revision History
Revision
1.00
Date
Des. 24, 2014
Description
Preliminary version
Important Notice
Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any
malfunction or failure of which may cause loss of human life, bodily injury or severe property damage.
Such applications are deemed, “Insecure Usage”.
Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy
control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or
safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and
other applications intended to support or sustain life.
All Insecure Usage shall be made at customer’s risk, and in the event that third parties lay claims to
Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the damages and
liabilities thus incurred by Nuvoton.
Des. 24, 2014
22 of 21
Rev. 1.00