Download RF Dimmer Receiver
Transcript
RF Dimmer Receiver 95.0 37.0 20.0 Model: SR-2501N series 85.0 SR-2501NS Brief introduction of buttons 1 Learning to sender 2 12-36VDC power input SR-2501N GND 4x5A 4x(60-180)W Constant voltage SR-2501NEA 12-36VDC 4x8A 4x(96-288)W Constant voltage SR-2502N 12-36VDC 4x350mA 4x(4.2-12.6)W Constant current 4x700mA 4x(8.4-25.2)W Constant current 12-36VDC 1x8A 1x(96-288)W Constant voltage SR-2502NS 12-36VDC 1x350mA 1x(4.2-12.6)W Constant current 12-36VDC 1x700mA 1x(8.4-25.2)W Constant current SR-2501N RF Easy Dimmer Learning Key GND hand hold RF remote SR-2801,SR-2802,SR-2828,SR-2807,SR-2801F SR-2805D wall mounted RF remote knob SR-2805R,SR-2805R(IT),SR-2805R(US), SR-2805NF,SR-2805TS wall mounted RF remote push SR-2801K1,SR-2801K2 (flat bottom, can be also stick on wall easily) wall mounted RF remotel touch SR-2805T1,SR-2805T2, SR-2805T1 (IT),SR-2805T1(US), SR-2805T2(IT),SR-2805T2(US) Notice: IT means Italian size, US means US size 4 Single color LED Strip Single color LED Strip Single color LED Strip 4 Push Switch Compatible with below RF remote on table RF remote knob 110V-230VAC 4x5A PUSH Single color LED Strip LED Product Size Push Switch GND PUSH 178.9 SR-2501NS RF Easy Dimmer N 45.5 Learning Key 110V-230VAC 18.6 L 170.4 SR-2501N Power Supply 12-36VDC Input 12-36VDC SR-2503NS Power Supply 12-36VDC L 12-36VDC Wiring diagram N SR-2503N SR-2501NS Power input 12-36VDC Learning Key 1 12-36VDC SR-2501N Learning to sender Input 12-36VDC Remarks 2 Output RF Easy Dimmer 3 Current 1 Iuput Voltage SR-2501NS Input 1-10V 1 channel 1-10V input For single color LED light For single color LED light LED Parameter Part No. Push Switch Connect to push switch Compatible with different remote controls Push Dim function available when connect a simple push switch To dim and switch Single color LED lighting. RF Easy Dimmer 3 Learning Key Feature Operation a. Do wiring according to connection diagram b. Short press learning key on receiver is when you do pair with remote (see the remote’s use manual accordingly once the receiver and remote well paired, the led light flashes means well learned. c . Long press the learning key on receiver over 5 seconds until LED light flash, then delete the learned ID, the receiver will be reset to factory defaults. d. When connected to Push Switch, short press push switch for switch ON/OFF, long press push switch to dim up, long press again to dim down Each receiver can be controlled by 8 different remotes in max. Warranty Agreement 1) We provide lifelong technical assistance with this product: 3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The warranty is for free repair or replacement and covers manufacturing faults only. For faults beyond the 3-year warranty we reserve the right to charge for time and parts. 2) Limited Warrenty Any defects caused by wrong operation. Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and replacement of chips. Any damages due to transportation, vibration etc. after purchase. Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage. Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near harmful chemicals. Product has been updated 3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer. Safety & Warnings 1) The product shall be installed and serviced by a qualified person. 2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof enclosure. 3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating. 4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the product. 5) Never connect any cables while power is on and always assure correct connections to avoid short circuits before switching on. 6) Please ensure that the cable is secured tightly in the connector 7) For update information please consult your supplier.