Download User Manual - RF-Link

Contents
Digital Wireless HDMI
Receiver
1.Imp ortant Safety Informa tion........................................ 1
2.Package Content........................................................ 2
3.Panel Layout and Function............ .............................. 3
4.Receiver Setup........................................................... 4
1.Important Safety Information
User’s Manual
To prevent fire or shock hazard, do not expose this product to rain and
moisture. For example: do not use near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or nearby a swimming pool. To
avoid electric shock, do not take apart this product, provided as an
accessory. This product should be operated only under power supply.
Do not overload wall outlets and extension outlets as this can result in
the risk of fire or electric shock.
FCC Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
Note:
This equipment has been tested and found to comply with the limits regulated
by FCC and CE. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction, may cause harmful interference to
radio communications. The change or modifcations not expressly approved by
the party responsible for compliance could void the user’s authority to operate
the equipment. To comply with the FCC RF exposure compliance requirements,
no change to the antenna or the device is permitted. Any change to the antenna
or the device could result in the device exceeding the RF exposure requirements
and void user’s authority to operate the device.
1
2.Package Contents
2.Package
3.Panel
Layout
Contents
and Function
Check to make sure that all units shown as below are enclosed.
If something missed, please contact your dealer.
1. 5.0GHz Receiver x 1
2. Stand x1
List of functions
Receiver unit
3
2
1
UHF:433.92MHz
5
7
6
4. Power Adapters x 1
3. HDMI Cable x 1
4
USA Type
EUROPE Type
1.
2.
3.
4.
5.
6.
7.
USB port
CH change / Reset button(*)
On / Off switch
HDMI port
Mini-USB port (power only)
Link LED (**)
Power LED (***)
* Press and hold this button within 3 seconds to change the channel. Keep
pressing over 3 seconds is to restart the system to default.
** Orange LED illuminate, when the transmitter links up with receiver and will
flash when the data is under transmission.
*** Green LED illuminate, when the power is on.
2
3
2.Package Contents
4.Receiver
Setup
4 .1 Driver installation
4 .3 Display Mode
1. Insert the provided MD into your computer’s CD drive.
2. Open the MD’s file from “My Computer” . This will open up
to a selection of software to be installed.
3. Double-click the execution file
(setup.exe), screen
will appear.
4. Follow the steps and click "Finish" to complete the
driver installation.
Mode
Icon
Description
Presentation
Presentation prefer
Video
Video prefer
Extension
Extension mode
5. Now, you can link the receiver from your PC.
4 .4 Button Instruction
4 .2 Utilities Operation
1. When starting to use the PC to TV HDMI receiver,
please make sure your Wi-Fi link is activated.
2. Open the selection of software list and double-click
the execution file
(WiPlay.exe) and select your
Items
Icon
Internet
Connect to AP/Router
Config
Frequency option
About
Program version and
firmware
Minimize
Minimized video
Exit System
On / Off wiplay
Start / Stop
Start / Stop program
Adjust
Adjust screen size
Wi-Fi adapter which one you want to use.
Screen will be as follows:
4
5
4 .5 Internet Shift
1. Choosing icon
Description
WEEE Directive & Product Disposal
, it will take a few seconds to search AP/Router
2. Choosing AP/Router you need
3. Click “Connect”
4. The receiver will restart by itself.
At the end of its serviceable life, this product should
not be treated as household or general waste. It
should be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.
4 .6 Config Shift
1. Choosing icon
2. Choosing frequency you need
3. Click “Save”
4. Restart the receiver when
screen show “Save successful”
Channel selection button to
find optional reception.
CH
4 .7 Installation
1. Connect the output device (TV, monitor, home theatre, etc.)
through the HDMI cable.
2. Connect the power supply adapter
3. Turn on the device. The power LED will illuminate.
6
TTD-D5006R
408-000708-00