Download ELECTRIC ` ELECTRIC
Transcript
ELECTRIC BALLooN PUMP 1.Open the cover board and take outthe e丨 ELECTRIC BALLooN PUMP ectrical、 ″ ire(Picture one) 2.Connectthe AC e丨 ectrical wire with the socket(Picture two) 3.Put the switch to‘ ‘ I” &motor startˉ up(Picture three) 4.Remove the ba"oon、 ″hen ba"oon size is suitable(Picture fourl <<田 X READ FOLLOWING INsTRuCTIONs AND WARNINGs BEFORE usE ˉ-ˉ {∶ sMALLNOZZ∶ E * DOn’ t disc。 nnect the pump with、 ″et hands and without to force the supp丨 y cord. * DOn’ trnove the pump、 ″ith aid of supp丨 y cord. * Use the pump only in the described【 ηanner. * lfthe pump is not used,please turn off. ∶}I-ˉ * DOnt use or stop the use ifthe pumpis damaged,especia"y ZOzZEL&-ˉ ˉ…ˉˉ the supp丨 y cord and the case. MlCRO sWlTCH 1■ ˉˉ PLUC IMPORTANT * Powersupp丨 y mustbe AC】 00-120V,50Hz。 * This pump is intended to balloons.Extended operation over 4hours can overheat and damage the pump. * Keep the pump out ofreach ofchHdren. * Do not obstruct the inflation port迈 ventilated aH the t∶ 1η 辶nozzles,keep them *DOn’ timmersethe pumpin"quid. * A periodicaHy rnaintenance ofthe pump is nocessary. * The pump don’ t put down near hot surfaces e.g.hotplate, oven etc.,because the rnaterial can smelt。 * The pump should not beimpeded by covering the venti丨 a- tion openings with items,such as newspapers,tab丨 eˉ oths, c丨 curtains,etci e. * Choose the suitable nozz丨 e to reduce the working time of pump when inflating the balloons. 3.TOINFLATE BALLONs * open the cover ofthe wire,take outthe、 2■ WARNING * TO reduce the risk,contact qua"fied electrician to repair or ″ire and close the cover(The、″ire can extend from the ho丨 e ofthe cover),connect plug to220ˉ 240V AC socket。 * Turn the switch on“ ’ ,cover the nozzle vvith the ba"onn; then press the right side ofthe nozz丨 es"ghdy inflate the baHoons and re丨 ease to stop. * FOrinflating the balloons continuous丨 y,please turn the l’ ace the damaged cord irnrnediately. * CarefuHy fo"owing the instructions when inflating the rep丨 ba"oons.Never exceed reco吖Wη ended pressure,other、 ″ise, serious inJury rnIght be caused by the bursting. * Neverleave the pump unattended、 ″hHe the pumpisin use. * DO not keep the pumpin、 Ⅳet condition。 * Never a"ow sand,small rocks,etc,to be sucked into inflaˉ tion port&nozzles when using the pump. * Never丨 ook inside or pointinf丨 ation part迈 0nozzles toward youreyes when the pump is working. ;then cover the nozz丨 e with balloon toinf丨 ate,and turn switch to“ O” to stop. sWitCh to“ II’ * FOrinflating big baHoons,coverthe ba"oon on the nozz丨 e direcdy;if inflat∶ ng sarnl丨 or thick rnaterial ba"oons,to screw the sma"nozzlos into the big nozzle to increase the pressure and reduc0the time ofinfIate.