Download Click to user manual
Transcript
The following pages and illustrations are printed to help supply you with the knowledge to better operate and service your new DOMRIES equipment. Any piece of equipment top running condition. needs, and must have a certain amount of service and maintenance to keep it in We have attempted to cover all the adjustments required to fit most conditions; however, there may be times special care must be taken to fit a condition. Study this operator's manual carefully and become acquainted with all the adjustments and operating procedures before attempting to operate your new equipment. Remember, it is a machine and has been designed and tested to do an efficient job in most operating conditions and will perform in relation to the service it receives. If special attention is required for some conditions, ask your DOMRIES dealer; his Parts and Service Organization will be glad to help and answer any question on operation and service of your new machine. This symbol is used to call your attention to safety precautions that should be followed by the operator to avoid accidents. When you see this symbol- It is the responsibility Heed Its Warning. of the user to read the Operator's Manual and understand the safe and correct operating procedures as pertains to the operation of the product, and to lubricate and maintain the product according to the maintenance schedule in the Operator's Manual. The user is responsible for inspecting his machine and for having parts repaired or replaced when continued use ofthe responsibility product would cause damage or excessive wear to other parts. It is the user's to deliver his machine to a DOMRIES dealer, for service or replacement of defective parts which are covered by the standard warranty. When requesting warranty service, you present your copy of delivery record. ATTENTION! BECOME ALBERT! YOUR SAFETY IS INVOLVED! This symbol is used to call your attention to safety precautions. That should be followed by the operator to avoid accidents. When you see this - Heed Its Warning. Many hours of lost time and much suffering is caused by the failure to practice simple safety rules. 1. READ this manual carefully to acquaint your - self with the Disk Harrow. Opening unfamiliar equipment 2. can cause accidents. LOWER IMPLEMENT if possible, when adjusting maintenance work; otherwise BLOCKS IT SECURELY at a workable height. 3. When Implement and tractor are parked always lower disk to the ground and place a FLAG OR OTHER WAARMING DEVICE on each corner as someone could run or bump into the implement. 4. Implement should be DETACHED ONLY in an area where Children DO NOT PLAY. 5. DO NOT wear loose fitting clothing that could catch on various parts. 6. Machinery should be OPERATED ONLY by those who are RESPONSIBLE AND DEEGATED to do so. 7. ONLY ONE PERSON - the operator - should be permitted operation, he should be thoroughly on the tractor when implement is in familiar with tractor and implement. 8. MAKE CERTAIN that everyone is in clear before starting tractor and implement 9. BEFORE WORKING under the any hydraulically controlled combination. unit IS SURE it is SECURELY BLOCKED. 10. The RATE OF SPEED on hillsides or curves should be regulated so there is no danger of tipping. 11. DO Not drive too close to the edge of a ditch or creek. 12. REDUCE SPEED when transporting unit to avoid bouncing and momentary loss of steer ability. 13. MAKE CERTAIN tractor is equipped with sufficient front end weight to counter-balance the plow weight and maintain stability of front of tractor. 14. DO NOT attempt to operate tractor and implement 15. ALWAYS place transmission unless you are in the diver seat. in PARK or NEUTRAL, LOCK BRAKES,STOP ENGINE AND REMOVE START KEY before dismounting from the tractor. 16. NEVER stand between tractor and disc when hitching. 17. PROVIDE a first aid kit. Treat all scratches, cuts, etc. with proper antiseptic immediately. 18. If DECALS become damaged or come off, they should be replaced immediately. 19. REMEMBER that safe operation is no accident. 1. Use the SLOW MOVING vehicle emblem in daytime and approved warning lights at night, or during other periods of poor visibility, to prevent highway accidents. 4. Due to the width of the implement, US EXTRA CAUTION on highways, far lanes and when approaching gates. Phone (559) 673-9143 Fax (559) 673-4110 ~ARRANTY Domries warrant's all products of it's manufacture to be free of defects in material and workmanship under normal usage and maintenance for the period of one year from the date of delivery to the original purchaser. RETURN GOODS Domries shall have the option of requiring the prepaid return of any parts claimed defective, however, No parts shall be returned without Domries warranty form with good authorized number. Goods shall be returned to such location as shall be designed by Domries. Domries will at it's option, either repair or replace, F.O.B. Domries factory. been defective in materials and/or workmanship. Such parts as appear to to Domries upon inspection, to have Wearing parts that are determined to be defective are subject to an adjustment based upon useful life. REPAIRS Any field or repairs must have the authorized repair number from Domries before any work is done. Claim for warranty must be made with a Domries warranty form and repair number. Domries will not accept any charged other than its direct Dealer shop labor costs and part required to remedy such parts and/or workmanship at its Dealer place of business. The WARRANTY specifically excludes any charges for delivery, transportation, and/or shipping cost. If the dealer is requested by the customer to travel or haul the machine to his shop or repair shop for the purpose of preforming a warranty obligation or free inspection, it would be for the customers convenience, and the cost of such a trip is to be paid by the customer. arrangement whereby the Dealer agrees to absorb all or a part of the cost is to be made between the Dealer and the Customer. Any To be considered a courtesy to the Customer by their Dealer. LIMITED WARRANTY Outside purchase equipment and accessories (not of Domries manufacture) are warranted only to the extent of the original manufacture's warranty to Domries. Item limited - Hydraulic cylinders and hose - Bearings - Disc Blades - Wheels - Tires - Tubes - Seals. No Warranty shall be paid by Domries before the part or parts and labor have been paid to Domries by the manufacturer. Domries shall then compensate the dealer or customer. NOWARRANTY (1) New product that has been subjected to operation in excess in recommended capacities, misused, negligence, lack of maintenance or accident or have been altered or repaired in any manner not authorized by Domries. (2) Sharp turns while machine is ground void warranty, with the exception of a drag disc. Domries shall in no event be responsible for any delay or any other consequential or indirect damage in connection with fulfilling any obligation under this WARRANTY. Domries reserves the right to make change at any time in designs, materials and/or specifications of it's product without becoming liable or obligated in any way to make similar changes in previously manufactured This WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES products. COVERING DOMRIES PRODUCTS and no other Warranties or implied are made or authorized by Domries Enterprises, Inc. This WARRANTY BECAME EFFECTIVE with shipments made on or after August 1st 1998 expressed Ref # Part # l. BT-10-10 BT-10-11 BT-10-12 BT-10-13 BT-10-14 BT-10-15 OH-136 OH-136-C OL-133 OL-134 OL-135 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 1- -----,---.-----------I I I I Hitch Assembly Angel Set Hitch Pin Outer Tube-DB Angle Inner Tube-DB Angle Draw Bar BTO Series Cross Member Hitch Hitch Pin BTO Series Hose Guide Clamping-Strap Tongue-Pin Clevis Type Tongue Single Lip Tongue Wt./lb Set Set 1 Offset 1 2 25.6 8.8 60 102 5 4.2 0.9 3.1 13.8 11 List Price Ref# Part# 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. BT-I0-17 BT-I0-27 BT-I0-28 BT-I0-29 BT-I0-52 BT-I0-53 BT-I0-149 OH-150 BT-20-08-16 SN114 OH-140 OH-143 JJ-60 CP14 OH-145 OH-148 MODE.L.~BTO-i \--- Leveling Rod Assembly Body-Turnbuckle Hammer-Leveling Link-Leveling Rocker Weldment (Swivel) Spring Guide-Double Spring Guide-Single Leveling Rod Spring Leveling Swivel, Leveling Rod Slotted Nut-1114nc, Hex Rod-Turnbuckle, LH Thd Rod-Turnbuckle, RH Thd Clip; Lock, Drag Link Cotter Pin Cross Pin Rocker Pin Wt./lb List Price 7.2 17 17.3 13.9 1.9 1.9 19.5 5.8 0.1 0.5 4.2 4.2 0.2 $ $ $ $ $ $ $ $ $ $ $ $ $ 78.30 82.08 38.34 75.06 18.58 18.14 98.82 64.35 56.50 4.75 30.78 30.78 6.32 2.5 0.7 $ $ 14.85 12.15 Ref # 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Part # BT-10-1 JJ-16 JJ-90 RPO-136 LW1 N1 N114 CS13-5 CS11412-5 W1029 Main Frame Assembly Main Frame-BTO Series 1 Axle-Block, 2 ~"d Hyd. Cylinder-3"dx12"stroke U' Bolt-1"d Spring Lock Washer Nut -1"nc, Hex Nut -1114nc, Hex Bolt -1"ncx3"lg Bolt - 1114ncx12lg Flat Washer Wt.lIb 635 5 30 4.9 0.1 0.1 0.6 0.9 7 0.3 List Price Ref # Part # l. BT-I0-0IA BT-I0-05 BT-I0-07 BT-I0-08 BT-I0-63 BT-20-02 BT-20-03 BT-20-06 OH-126 OH-148 2. 3. 4. 5. 6. 7. 8. 9. 10. Split Axle Assembly Crank Assy-Split Type Axle Strap Swivel Axle Half Assy-RH, Series 1 Axle Half Assy-LH, Series 1 Set Bar Depth Control Swivel Nut-Threaded Swivel Nut-Plain Bushing-Crank Swivel Set Bar Pin Pin Rocker Wt.llb 6 5.3 75 157 23.5 1.6 1.5 0.1 0.6 0.7 List Price Ref # Part # 1. DSH-302 DSH-303 DSH-304 DSH-305 DSH-306 DSH-307 DSH-308 DSH-309 DSH-310 DSH-312-S DSH-313 DSH-314 DSH-316 DSH-318 JJ-19 JJ-20 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. \---_._I .--------- Spindle Assembly Hub Bearing Cup, Outer Bearing Cone, Outer Bearing Cup, Inner Bearing Cone-Inner Inner Seal Outer Seal Tubing Sleeve Clamp Assy Slip in Spindle Slotted Nut Spindle Washer Dust Cap Lug Bolt-(1I2"nfxl "Long) Wheel-15x6,6(1I2) Tire- 7.60-15, Rib 6 Ply --- - -_ ... ----.--_._-----_._-------- Wt.llb 10 0.1 0.3 0.2 0.4 0.1 0.1 0.3 0.31 9 0.1 0.01 0.2 0.1 23 24 List Price Ref # 1. 2. Part # BT-10-16F BT-I0-18F BT-I0-20F BT-I0-22F BT-I0-24F BT-I0-26F BT-I0-28F BT-I0-16R BT-I0-18R BT-I0-20R BT-I0-22R BT-I0-24R BT-I0-26R BT-I0-28R Gang Frame Gang Gang Gang Gang Gang Gang Gang Gang Gang Gang Gang Gang Gang Gang Frame-8 Blade, Front Frame-9 Blade, Front Frame-l0 Blade, Front Frame-II Blade, Front Frame-12 Blade, Front Frame-13 Blade, Front Frame-14 Blade, Front Frame-8 Blade, Rear Frame-9 Blade, Rear Frame-l0 Blade, Rear Frame-II Blade, Rear Frame-12 Blade, Rear Frame-13 Blade, Rear Frame-14 Blade, Rear Wt./lb List Price 202 218 234 250 267 284 301 192 208 225 241 258 274 290 I I I j Ref # 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Part # XGR-4 XGR-5 XGR-6 XGR-7 XGR-8EL XGR-9EL JXE-18 JXE-19 RPO-129D-KIT RPO-104 RPO-113 RPO-114 RPO-117 RPO-133 LW112 SN112 CP14 Gang Assembly Gang Rod-1 1/2sq, 4 Blade, Gang Rod-1 1I2sq, 5 Blade, Gang Rod-1 1I2sq, 6 Blade, Gang Rod-1 1I2sq, 7 Blade, Gang Rod-11/2sq 8 Blade, Gang Rod-1 1I2sq 9 Blade, Ext. Washer-CVX 1112sq Ext. Washer-CCV 1112sq Brg. Assy. 1 W' Ear Type Full Spool 1 %"SQ. 9" Half Spool- CVX, 1112sq Half Spool- CCV, 1112sq Mtg. Strap-Flat, Brg Offset Bearing Guard Lock Washer-Spring Slotted Nut 1112"nc Cotter Pin List Price Wt./lb 9" 9" 9" 9" 9" 9" 20 26 32 38 44.2 50.2 9 8 11.4 19.4 10.7 5.8 3.7 7.5 0.2 0.8 $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ 53.24 57.24 61.56 66.96 83.70 93.96 34.11 34.11 111.25 52.75 52.25 36.75 16.95 19.95 1.80 6.25 6.4 3.5 0.1 $ $ $ 41.25 63.50 4.15 RPO-129D-KIT 1. 2. 3. RP081 RPO-103D RPO-99 I I~ RPO-129D-KIT Bearing Housing-1 1I2sq, Ear Type Gang Bearing Assy 1 1/2sq Retaining Ring Ref # 1. 2. 3. 4. 5. 6. 7. 8. Part # BT-308 BT-309 BT-310 BT-311 BT-312 BT-313 BT-314 RPO-15 RPO-116+clip RPO-120 CS12434-5 CS12312-5 LW12 N12 Cleaner Bar Assembly Wt.IIb Scraper-Bar Scraper-Bar Scraper-Bar Scraper-Bar Scraper-Bar Scraper-Bar Scraper-Bar Scraper-Blade Scraper-Arm Scraper-Clip Arm Bolt-1I2ncx43/4Ig Bolt-1I2ncx3 1I2lg Lock Washer-Spring Nut-1I2nc, Hex List Price 13.4 15.3 17.2 19.2 21.2 23.2 24.2 2.5 3 0.4 0.3 0.3 0.1 0.1 -------l I ~~ 5 @~ C]f ._~----_. -----, I Ref # 1. 2. 3. 4. 5. 6. 7. 8. Part # JXE-17 JXE-20 CS12112-5 LW12 N12 CS58112-5 LW58 EXB-24" EXB-24N EXB-26" Extension Spool Assembly Ext. Spool-(Blade Pulls In) 9" Cap-Ext. Spool, Universal, 1 Y2 Bolt-1I2ncx1112Ig, GR 5 Lock Washer-Spring Nut-1I2nc, Hex Bolt-5/8ncx1112Ig GR 5 Lock Washer-Spring, Ext. Blade-24"d SId Edg, 1112sq Ext. Blade-24"d Ntched, 1 1/2sq Ext. Blade-26"dia, Solid Edge Wt.llb List Price 11 3 0.1 0.1 0.1 0.3 0.1 25 23 31.5 ---------------------1 \ \