Download MAJESTIC 8000 WITH CLASSIC 6004
Transcript
MAJESTIC 8000 WITH CLASSIC 6004 x4 x1 x4 x10 x4 x4 x2 x6 WARNING x2 x2 Do not dive or jump from step or ladder. Use BATTERY operated tools to avoid electric shocks. Install step on flat surface, following the manufacturers instructions. Remove step from pool during freezing climate season. Manufacturer cannot be held responsible for injuries caused by abusive use of product. Ask your city about specific regulations that apply to your above-ground pool and ladder. x2 x1 x1 29.25" x2 35" x4 105-005 x2 105-012 115-014 (3/4 in.) 115-008 (1 3/4 in.) 125-035(1.0 in.) 115-018 (2 1/2 in.) 39" SCREW BAG 558-001 105-005 105-012 115-014 (3/4 in.) 115-011 115-015 (1 1/2 in.) 115-018 ( 2 1/2 in.) SCREW KIT 140-019 67" Contents of the ladder box SKU # 6004 Contents of SKU box # 8000 x2 x2 x22 x4 x4 Majestic step Security strap x2 Tools Required (not included) A weather resistant padlock is recommended. Maximum functional width is 1/4 inch. Sand (not incl.) Sand 25 lbs A 5/16" Drill Bit 1) Insert the two 39" posts into the step recesses and secure them in place with the bolts, washers and nuts provided. 115-014 2) Slide the two spacers on the top post. Do not secure yet. 3) Insert the handrail over the left side posts. Secure it using the screws provided. Snap the post cover. 105-005 105-012 115-011 x4 x4 x4 x4 250 industrial blv, St-Germain (Québec), Canada J0C1K0 PG. 1 REV. 02/02/10 B 1) Slide the platform on the flanged post. 3 2) Insert the 29.25" hollow post, on the other side, through the spacers and platform. 3) Insert the two small handrails over the posts. Do NOT secure yet. C 4) Once inserted in the spacers, use the 29.25" hollow post as a pivot to slide the flanged post on the other side. Drill (5/16") holes. 1) Make sure to leave a 1/4" clearance between the bottom spacer, and the top of the step. Secure in place with the screws provided. 2) Mesure 12" between the two spacers. Secure in place with the screws provided. 4 2 12" 3) Do NOT secure the platform yet. 5) Secure the flanged post with the bolts, washers and nuts provided. 1 x2 D 115-014 (3/4 IN.) 105-005 105-012 115-008 5 1/4" x2 x2 Insert the Step CupTM in the 6 holes under the step. 1) Insert half of the Step CupTM mushroom in the hole, at a 45 degree angle. x8 E 1) Slowly submerge the step into the pool. Make sure you do not damage the pool liner in the process. 2) Apply firm pressure on the step to allow the Step CupTM to stick on the pool bottom. Do NOT secure the platform yet. 2) With a flat screwdriver, compress the Step CupTM mushroom ring while pushing it into the hole. *MINIMUM OF 1" 3) Twist the Step CupTM to ensure that its mushroom has entirely cleared the wall thickness. If it has, the suction cup should rotate freely. x6 250 industrial blv, St-Germain (Québec), Canada J0C1K0 *All Step CupTM must be installed CAUTION* To prevent a pool liner puncture, install all Step Cup™ as specified and keep a minimum of 1" inch gap between the pool liner and the rear underside of the step. Failing to install the Step cup ™ will greatly reduce the steadiness of the step and will void the manufacturer warranty. REV. 25/01/09 PG. 2 2) Slide the pivot blocks onto the posts and line up with the traced marks. Secure with the screws provided. 3) Slide the 2 posts through the platform and handrails. G 1) Slide the platform downwards and let it sit on the top seat of the pool. 2) Secure the handrails and platform to the posts with the screws provided. 4) Secure the ladder base to the post with the screws provided. 115-014 (3/4 in.) 115-014 (3/4 IN.) F 1) Trace a line on each post at 39 inches from the ground for 48'' & 52'' pools. If you have a 54'' pool, trace a line at 40.5'' from the ground. x6 This one on the side x11 105-012 39'' 40.5'' x2 1) Once the step is in the pool secure the platform to the top seat (see illustration) using the two straps provided. J x2 115-018 (2 1/2 in.) H Security strap 105-005 3) Secure the ladder to the pivot blocks using the bolts, washers and nuts provided. 125-035 align x2 x2 Use sliding lock as a guide to drill hole into ladder in up position. Use a 5/16'' drill bit. **PADLOCK REQUIRED** OPTIONAL: x2 Once the pool step has been completely assembled and secured to the pool, attach the 2 screws supplied through the platform to the top seat of your pool to provide a more rigid assembly. 2) Secure the counterweight cover with the screws provided. 115-014 (3/4 in.) San d I 1) Fill the counterweight to the brim with sand. X4 WARNING SWING THE LADDER UP AND LOCK IN PLACE WHEN THE POOL IS NOT IN USE TO PREVENT DROWNING AND UNAUTHORIZED ENTRY. MANUFACTURER WARRANTY 250 industrial blv, St-Germain (Québec), Canada J0C1K0 1 year on the ladder and step. 1 year on the hardware. REV. 02/02/10 PG. 3 MAJESTIC 8005 Majestic step Contents of box # sku 8005 Sand (not included) SCREW KIT 8005MJ08 x4 x4 x4 x6 115-015 (1 1/2 in.) 115-014 (3/4 in.) 115-010 105-012 105-005 x6 d San x1 x10 WARNING Tools required (not included) Do not dive or jump from step or ladder. Use BATTERY operated tools to avoid electric shocks. Install the pool step on a flat surface Remove step from pool during freezing climate season. Manufacturer cannot be held responsible for injuries caused by abusive use of product. Ask your city about specific regulations that apply to your above ground pool and ladder. 105-005 105-012 115-010 115-014 A 1.Assemble the two handrail halves. 2.Insert the handrail into the recesses. x2 x4 B Insert the Step CupTM in the 6 holes under the step. 3.Fasten the hand-rail to the step using the screws, washers and nuts provided. x4 x4 x6 1) Insert half of the Step CupTM mushroom in the hole, at a 45 degree angle. 2) With a flat screwdriver, compress the Step CupTM mushroom ring while pushing it into the hole. CAUTION 250 Industriel Blv, St-Germain, (Québec), Canada J0C1K0 3) Twist the Step CupTM to ensure that its mushroom has entirely cleared the wall thickness. If it has, the suction cup should rotate freely. Failing to install the Step Cup ™ will greatly reduce the steadiness of the step and will void the manufacturer warranty. REV. 17/02/10 PN: 110-104 PG. 1 115-014 (3/4 in.) San d C 2) Secure the 1) Fill the counterweight counterweight to the brim with sand. cover with the screws provided. X4 E D 1) Slowly submerge the step into the pool. Make sure you do not damage the pool liner in the process. *MINIMUM OF 1" CAUTION* *All Step CupTM must be installed To prevent a pool liner puncture, install all Step CupTM as specified and keep a minimum of 1"inch gap between the pool liner and the rear underside of the step. 1) Apply firm pressure to step by walking along the steps to engage the Step CupTM . 2) Affix the small arm to the handrail vertical post using the 4 screws. 115-015 3) Align the step carefully and fasten the arm to the deck. 4) Install the counterweight in the step. x10 POOL DECK ABOVE POOL TOP SEAT POOL TOP SEAT FLUSH FIT WITH DECK POOL MANUFACTURER WARRANTY 1 year on the Majestic pool step. 1 year on the hardware. TOP SEAT DECK POOL DECK OFFSET FROM TOP SEAT DECK POOL DECK OFFSET FROM TOP SEAT Spacer block not included 250 Industriel Blv, St-Germain, (Québec), Canada J0C1K0 TOP SEAT TOP SEAT AFFIX SPACER BLOCK ON TOP SEAT DECK SPACER BLOCK NOT INCLUDED DECK REV. 17/02/10 PN: 110-104 PG: 2