Download CM6800E-48X8 Matrix Switcher

Transcript
INSTALLATION/OPERATION
®
CM6800E-48X8
Matrix Switcher
C1528M-G (9/06)
Contents
Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Compatible Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Associated Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Video Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Control Lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Connecting Devices through the Communication Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
KBD100, KBD200A, and KBD300A SERIES Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
M Devices (KBD960, ALM2064, REL2064) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Connecting a PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Connecting Genex Multiplexers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Local Auxiliaries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Connecting a 96 x 16 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
System Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Power-up the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Initialize Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Configure the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Communication Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
96 x 16 System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
KBD960/KBR960 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Genex Multiplexer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Monitor Color Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Program Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Additional Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Programming the CM6800E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
CM6800E Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Navigate and Select Options/Field Entries in Programming Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Restrict System Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Set Satellite View Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Change PTZ Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Alarm Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Program Alarm Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Program an Internal or External Alarm Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Program a Video Loss Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Assign a Logical Alarm Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Auxiliary Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Camera Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Program Logical Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Program Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Event Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Macros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Macro Status View Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Monitor Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Ports (Serial/COM Ports) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Priority . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
96 X 16 System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
C1528M-G (9/06)
3
Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Time and Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Patterns, Presets, and Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Operating the CM6800E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Switch Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Select Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Control Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Operate Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Run a Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Acknowledge an Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Call a Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Create and Run a Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Operate Auxiliaries/Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Control Genex Multiplexer and Genex Multiplexer Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Operate Scanning Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Detect Video Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Define Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
CM6800E Dip Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Alarm Group Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Block Build . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Chronological Pair: D and Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Reverse Chronological Pair: M and L . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Salvo Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Macro Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Using the CM6800E-48X8 as a Satellite Device in a 9700 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Install the CM6800E as a Satellite Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Configure the CM6800E as a Satellite Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Configure CM9700-MGR System Manager Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Configure CM9760-MGR System Manager Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Navigate with the CM9740/CM9760 Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Logical Number Assignment Table – For Link Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
ASCII Operating Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Gaining Initial Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Software Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Solutions to Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
KBD960/KBR960 Icon/Button Legend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Upgrade the CM6800 Switcher Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Verify that Each CM6800E-48X8 Unit Contains the Same Level of Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
4
C1528M-G (9/06)
List of Illustrations
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
C1528M-G (9/06)
Sample CM6800E-48X8 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Sample CM6800E 96 x 16 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Sample CM9760 System with CM6800E-48X8 as a Satellite Switcher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installing Rack Ears. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Mounting the CM6800E Matrix Switcher/Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CM6800E Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connecting Terminated Video Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Connecting Looping Video Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PTZ Control Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Connecting Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Communication Port Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
CM6800E Communication Port Connections and Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Data Cable Plugged into Local Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Data Cables Plugged into COM 5 and 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Remote Keyboards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
RJ-45 Cable Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Connecting a KBD960/KBR960 to the CM6800E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Connecting a Single ALM2064 Alarm Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Connecting a Single REL2064 Relay Interface Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Connecting Multiple M Devices – Local Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Connecting Multiple M Devices – Remote Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
PC Connection to DB9 Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
PC Connection to RJ-45 Port. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Connecting Genex Multiplexers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Wiring the AUX 1 and 2 (Relay) Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Wiring the F3 (TTL) Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Data and Video Connections Between CM6800E-48X8 Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
CM6800E Time/Date Stamp on Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
CM6800E Color Bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
CM6800E Password Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
CM6800E Programming Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Sample Access Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Program Alarm Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Program Internal and External Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Program Video Loss Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Assign a Logical Alarm Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Program Auxiliary Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Program Logical Camera Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Program Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Sample Event Timer Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Macro Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Macro Status View Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Monitor Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Set Password Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Port Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Access the Priority Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Change the System Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Sequence Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Scratchpad Sequence Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Access the Time and Date Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
CM6800E DIP Switches – Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Data and Tie Line Connections Between CM6800E-48X8 and CM9700/CM9740/CM9760 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Set Satellite Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Change the Port Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Enable Alarm Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Assign Satellite Logical Alarm Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
5
58
59
60
61
62
63
64
65
66
67
68
Add a Satellite Device in the CM9700-MGR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
CM9760-MGR Comms Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
CM9760-MGR Cameras Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
CM9760-MGR Link Cameras Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
CM9760-MGR Alarms Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Alarm Camera Switches Dialog Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
CM6800E Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
DIP Switch Cover Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
CM6800E DIP Switch 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Icon/Button Legend. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Upgrade the CM6800 Switcher Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
List of Tables
A
B
C
D
E
F
G
H
I
J
K
6
Video Coaxial Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Communication Port Devices and Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Default Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Keyboard Addresses: KBD100/200A/300A Series Keyboards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Switch Settings—KBD200A/300A Keyboards Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Default Port Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
CM6800E DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Macro Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Examples of ASCII Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
ASCII Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Solutions To Common Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
C1528M-G (9/06)
Important Safeguards and Warnings
1. Read, keep, and follow these instructions.
2. Heed all warnings.
3. There are no user-serviceable parts inside this unit. Only authorized service personnel may open the unit.
4. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
5. WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture if this unit is designed for indoor use only.
6. Unless this unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for indoor use only and it must not
be installed where exposed to rain or moisture.
7. Do not expose this unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on this unit.
8. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
9. The installation method and materials should be capable of supporting four times the weight of the unit and equipment.
10. Do not install near any heat source.
11. Only use attachments/accessories specified by the manufacturer.
12. Clean only with dry cloth.
13. Do not defeat the safety purpose of the polarized or grounding-type plug.
14. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from
the unit.
15. Unplug this unit during lightning storms or when unused for long periods of time.
16. A CCC-approved power cord must be used to power this equipment when used in China.
The product and/or manual may bear the following marks:
WARNING: This symbol indicates that dangerous voltage constituting a risk of electric
shock is present within this unit.
This symbol indicates that there are important operating and maintenance instructions in
the literature accompanying this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.
FOR QUALIFIED SERVICE PERSONNEL ONLY
1. Only use replacement parts recommended by Pelco.
2. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to verify
the exposed parts have not been connected to line circuitry.
3. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used batteries
according to the instructions provided by the battery manufacturer.
C1528M-G (9/06)
7
Description
Pelco’s CM6800E Matrix Switcher/Controller is a cross-point video matrix switcher. The CM6800E-48X8 provides switching and control for
48 video inputs and eight monitor outputs from any one of up to 18 keyboards, PCs, and other devices. All 48 video inputs can be used to view
video from other devices, such as multiplexers. Forty inputs allow for looping to other devices.
The CM6800E-48x8 can be used in the following configurations:
•
A single unit provides up to 48 inputs and eight outputs
•
Two CM6800E-48X8 units can be combined into a “bay-to-bay” 96 x 16 system, providing switching and control of up to 96 inputs and
16 outputs from the main unit.
•
The CM6800E-48X8 can function as a remote satellite switcher in a CM9740/CM9760 System, allowing the system to handle additional
video, alarm, and relay inputs, as well as allowing for use of M protocol devices, such as external alarm and relay units.
Figure 1. Sample CM6800E-48X8 System
8
C1528M-G (9/06)
REL2064 (ADDITIONAL RELAYS)
ALM2064 (ADDITIONAL ALARMS)
ALARM 1
CAMERA 48
ALARM 8
CAMERA 96
CAMERA 1
ALARM 9
ALARM 16
CAMERA 49
PTZ
CONTROL
CM6800E-48X8 MAIN UNIT
PTZ
CONTROL
CM6800E-48X8 EXPANSION UNIT
DATA CABLE
VIDEO RIBBON CABLE
MONITOR 1
MONITOR 8
MONITOR 9
MONITOR 16
ALL KEYBOARDS CONNECT TO MAIN UNIT
GENEX MULTIPLEXER
Figure 2. Sample CM6800E 96 x 16 System
OTHER REMOTE SITES
REMOTE SITE
LOCAL SITE
CM6800E-48X8
CM6800E-48X8
CPU
1-48 CAMERAS
RS-422
DATA
LINE
MATRIX
BAY
CM6800E-48X8
KBD300A
VIDEO TIE
LINES
CM9740/CM9760
CM9760-KBD
Figure 3. Sample CM9760 System with CM6800E-48X8 as a Satellite Switcher
C1528M-G (9/06)
9
Programming
The CM6800E features easy programming through on-screen menus or the Windows®-based CM6800-MGR software package. All
programming is password-protected. Programming menus are provided in English, French, German, Italian, Polish, Portuguese, Russian, and
Spanish.
Keyboards
Up to 16 keyboards from the KBD100/200A/300A Series and 2 keyboards from the KBD960/KBR960 Series can be connected to the CM6800E.
Camera positioning can be programmed and controlled from the KBD200A/300A (in “6800 Mode” only) and KBD960/KBR960 Series keyboards.
Refer to Associated Equipment for keyboard descriptions.
NOTE: You can program the CM6800 with the KBD200A/300A keyboard while in “CM6800 Mode” only (if you use “CM6800 ASCII Mode,” you
can control the CM6800 switcher, but you cannot program it).
Sequences, Macros, Presets, Patterns, and Zones
The CM6800E features the following programmed operations:
•
Sequences: The CM6800E supports 32 programmable sequences. A sequences allows operators to see a routine of 72 camera views on
any system monitor over and over again. The sequence can be operated automatically or manually.
•
Scratchpad Sequence: A scratchpad sequence allows an operator to run a sequence from an individual monitor without entering the
password-protected programming menus.
•
Macros: The CM6800E supports 64 system macros. A macro is a sequence of commands or steps. When a macro is run, the steps
programmed into that macro are performed. Macros can be operated automatically or manually. Automatic operation can be based on
specific times or dates. Macros can also be triggered by alarms.
The following operations are available only with positionable cameras controlled by KBD200A/KBD300A or KBD960/KBR960 keyboards:
A preset allows operators to direct a PTZ (camera positioning system) to move to a predetermined scene on keyboard command or as a
result of an alarm. In addition, a preset can place a descriptive title on the monitor screen. The number of presets available is determined
by the camera positioning system.
With a pattern operators can program a camera positioning system to move around its viewing area in a repeating pattern. The number
and time length of patterns varies with different positioning systems.
A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is associated. When the associated camera is
panned through or remains within this defined zone, the zone label appears on the monitor.
Interface Control
The CM6800E interfaces with the following:
•
Coaxitron® standard mode (15-bit) and extended mode (32-bit) protocol receivers
•
Pelco’s D and P protocol receivers (RS-422)
•
Pelco’s M protocol devices (RS-485)
System Access and Priority
The CM6800E provides the following ways to restrict system access:
•
Camera to Monitor: Cameras can be assigned to specific monitors for viewing.
•
Keyboard to Monitor: Keyboards can be assigned to control specific monitors.
•
Camera to Keyboard: Keyboards can be assigned either full control or view-only access to specific cameras (no PTZ control).
The CM6800E provides eight levels of priority control. Each level defines the ability of a keyboard to control a camera positioning system
(KBD200A/KBD300A or KBD960/KBR960 only) and to access programming screens.
10
C1528M-G (9/06)
Alarm Inputs
Eight internal alarm inputs are provided on the rear panel of the matrix switcher/controller. These internal alarm inputs are programmable to
associate any camera to any input. A 96 x 16 system provides 16 internal alarm inputs (eight on each CM6800E-48X8 unit).
Up to four ALM2064 Alarm Interface Units can be connected to the CM6800E (main unit only in a 96 x 16 system). Each alarm interface unit can
handle up to 64 alarms.
Auxiliary Outputs
Three internal auxiliary outputs are provided on the back of the CM6800E. Two are relay outputs, and one is an open collector (TTL) output.
A 96 x 16 system provides a total of 6 internal relay outputs (three on each CM6800E-48X8 unit). Auxiliary outputs are activated at the keyboard
(except KBD100).
You can also connect up to four REL2064 Relay Interface Units to the CM6800E (main unit only in a 96 x 16 system).
Power, Mounting Methods
The CM6800E operates on 120 V or 230 V, 50/60 Hz. The case mounts in three rack units (5.25 inches or 13.34 cm) of vertical space in a universal
mount, such as a 19-inch (48.26 cm) equipment bay, or to a wall or tabletop.
Continuous Operating Device
The CM6800E is a self-contained video surveillance system designed for continuous duty operation. Once installed, no user or service technician
items require the power to be turned off under normal operation. There are two methods for system programming: direct menu control and
indirect control, using a Windows®-based setup program supplied by Pelco. Both of these methods are noninvasive and do not require the cycling
of power in order for storage or execution of new software settings. The communication ports use standard low voltage interfaces (RS-232,
RS-422 and RS-485), and all connections and disconnections do not require rebooting or power cycling. Video connections or changes of
termination state do not require rebooting or power cycling.
COMPATIBLE PRODUCTS
Switchers
CM9740, CM9760, CM9770, CM9780
PelcoNet Transmission Systems
NET300 Series, NET350 Series, NET4001A
Video Management Systems
VMX200, VMX300, VMX300-E
ADDITIONAL RESOURCES
•
CM6800E-48X8 Quick Start Guide
•
CM6800-MGR Installation/Operation Manual
•
Pelco Technical Tips; available on the CM6800 Resource CD (which is shipped with the matrix switcher) and on Pelco.com, or from a
Technical Support representative (1-800-289-9100)
C1528M-G (9/06)
11
MODELS
CM6800E-48X8
Matrix switcher/controller, 48 video inputs and 8 monitor outputs, NTSC-configured, 120/230 VAC, 50/60 Hz, autoranging
CM6800E-48X8-X
Matrix switcher/controller, 48 video inputs and 8 monitor outputs, PAL-configured, 120/230 VAC, 50/60 Hz, autoranging
CM6800-96X16
Expanded switcher/controller system; contains two CM6800E-48X8 units and one CM6800EKIT. 96 video inputs,
16 monitor outputs, NTSC-configured, 120/230 VAC, 50/60 Hz, autoranging
CM6800-96X16-X
Expanded switcher/controller system; contains two CM6800E-48X8-X units and one CM6800EKIT. 96 video inputs,
16 monitor outputs, PAL-configured, 120/230 VAC, 50/60 Hz, autoranging
CM6800E-KIT
Expansion kit containing cables and instructions needed to connect two CM6800E-48X8 units in a 96 x 16 system
ASSOCIATED EQUIPMENT
KBD100
Desktop keyboard with full switching and programming capabilities, +12 VDC or 12 VAC 50/60 Hz
KBD200A
Desktop keyboard with full switching and programming capabilities, plus push-button control of PTZ functions, +12 VDC or
12 VAC 50/60 Hz
KBD300A
Desktop keyboard with full switching and programming capabilities, plus joystick control of PTZ functions, +12 VDC or
12 VAC 50/60 Hz
KBD960/KBR960
Keyboards
Keyboard Series
Power Cord
Keyboard Model Number
KBD960: Full-function desktop variable-speed keyboard.
100-240 VAC, 50/60 Hz.
US
KBD960-US
UK
KBD960-UK
AU
KBD960-AU
KBR960: Full-function 19-inch EIA rack mount keyboard (4 RUs).
100-240 VAC, 50/60 Hz.
12
EU
KBD960-EU
US
KBR960-US
UK
KBR960-UK
AU
KBR960-AU
EU
KBR960-EU
KBDKIT
Wiring kit for connecting KBD100, KBD200A, and KBD300A keyboards to remote keyboard port; includes two RJ-45 wall
blocks and a transformer to convert 120 VAC, 60 Hz to 12 V, 60 Hz for keyboard power
KBDKIT-X
Wiring kit for connecting KBD100, KBD200A, and KBD300A keyboards to remote keyboard port; includes two RJ-45 wall
blocks and a transformer to convert 230 VAC, 50 Hz to 12 V, 50 Hz for keyboard power
CM9505UPS
Universal Power Supply for KBD960/KBR960 keyboards
MX4000
Genex® Series Multiplexer; available in color or monochrome duplex, and in color or monochrome simplex
CM9760-CDU-T
Code distribution unit; 16-channel RS-422 transmit only (transmit wire and ground) distributor; primarily used for
connecting up to 16 PTZ receivers in a “star” or “home run” configuration
ALM2064
Alarm interface unit, provides alarm monitoring capabilities for up to 64 alarm inputs, 100-240 VAC, 50/60 Hz
REL2064
Relay interface unit, provides 64 relays for operating peripheral equipment, 100-240 VAC, 50/60 Hz
CM9760-MDA
Master distribution amplifier with time, date, and title, 120 VAC, 60 Hz
C1528M-G (9/06)
Installation
Unpack and inspect all parts carefully. The following parts are supplied:
1
CM6800E Switcher/Controller
4
10-32 x 0.750-inch pan head screws
4
0.500” OD nylon washers
1
Power cord
4
6-foot (1.8 m) straight data cables with RJ-45 connectors
1
6-foot (1.8 m) reversed data cable with RJ-45 connectors
4
RJ-45 wall block terminals
NOTE: There are no user-serviceable parts inside this unit. Only authorized service personnel may open the unit.
MOUNTING
1. Select a suitable location for the CM6800E. It occupies 5.25 inches (13.34 cm) of vertical space, or three rack units (RUs), in a universal
mount. The CM6800E must be within 6 feet (1.8 m) of a suitable electrical outlet.
Follow proper installation practices and leave 1 RU above and below the CM6800E for ventilation. If installing a 96 x 16
system, in one vertical rack, leave 1 RU between each CM6800E-48X8 unit for ventilation.
Do not connect the power until the installation is complete. Refer to the System Start-up section.
2. The CM6800E is shipped with the rack ears installed at the front. Reposition or remove ears as needed for your application.
POSITION BRACKETS FOR
RACK MOUNTING (REAR)
POSITION BRACKETS FOR
UNDER-TABLE MOUNTING
NOTE: EACH CM6800 COMES
WITH 2 RACK EARS
POSITION BRACKETS FOR
RACK MOUNTING (FRONT)
POSITION BRACKETS FOR
FLUSH MOUNTING
(WALL AND TABLE TOP)
Figure 4. Installing Rack Ears
3. Use supplied pan head screws and washers to mount the CM6800E in a standard 19-inch (48.26 cm) equipment rack or wood or sheet
metal screws to mount against a flat surface, according to your installation requirements.
Figure 5. Mounting the CM6800E Matrix Switcher/Controller
C1528M-G (9/06)
13
VIDEO SOURCES
The CM6800E offers 48 full-function video inputs which support Coaxitron PTZ control and video loss detection. Forty video inputs, labeled
1 through 40, can be used for looping video connections with terminating and unterminating switches on the back panel. The eight alternate
source inputs, labeled 41 through 48, are terminated inputs. They do not have loop-through connectors or selectable termination switches, but
otherwise they offer the same functionality as video inputs 1 through 40.
All 48 video inputs also provide the ability to view and interface with other devices, such as Genex multiplexers. If control of the device
connected to the video input is required, connect a data cable between the multiplexer and the CM6800E. Refer to the Connecting Genex
Multiplexers section for instructions on connecting and controlling video from a multiplexer.
96 x 16 System Default Camera Numbers
Main unit:
Expansion unit:
Cameras 1-48
Cameras 49-96
HZ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
75
1
2
17
33
18
34
19
35
20
36
21
37
22
23
38
39
24
40
25
26
27
28
29
30
31
32
41
42
43
44
1
2
3
4
45
46
47
48
5
6
7
8
3
4
ALT
40 VIDEO INPUTS SELECTABLE
FOR TERMINATED OR LOOPING
8 TERMINATED ONLY
Figure 6. CM6800E Video Inputs
1. Connect video cables at the appropriate video input BNC receptacles on the back of the CM6800E. For best results, use crimp-on BNCs only.
Do not use screw-on BNCs; these typically do not provide adequate ground and signal connections.
Refer to Table A for video coaxial wiring requirements.
Table A. Video Coaxial Cable Requirements
Cable Type*
Maximum Distance
RG59/U
750 ft (229 m)
RG6/U
1,000 ft (305 m)
RG11/U
1,500 ft (457 m)
*Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
14
C1528M-G (9/06)
2. On video inputs 1 through 40, set the terminating switches according to your system requirements. Video inputs 41 through 48 cannot be
used for loop-through connections.
Terminating switches are used to terminate or unterminate the video input. The factory default has the switches set in the terminated
(75-ohm) position.
If you are connecting only a camera to an input, leave the switch in the terminated position.
Figure 7. Connecting Terminated Video Sources
If you are looping the input to another device, set the rear panel switch in the unterminated (Hi-Z) position. Terminate at the final device.
Figure 8. Connecting Looping Video Sources
NOTE: The end point of any video cable run must be terminated in 75 ohms.
C1528M-G (9/06)
15
CONTROL LINES
You cannot connect a Coaxitron camera to the PTZ-A or PTZ-B ports. If your video sources are all controlled by Coaxitron, skip this section.
Connect camera control lines to receivers. If any of your video sources are using D or P protocol via RS-422 communications, they will connect at
the PTZ-A and PTZ-B connectors on the back of the CM6800E.
NOTE: D and P protocol receivers cannot be mixed on the same communication port but you can use D on one port and P on the other.
Daisy-chaining (going from one receiver to another) is recommended but not always possible. A maximum of 16 receivers can be daisy-chained
from each port. If more than 32 receivers are required for your system, or if you do not want to daisy-chain the receiver connections, use the
CM9760-CDU-T. You can connect up to four CM9760-CDU-T units to the CM6800E (a total of eight in a 96 x 16 system - four connected to each
CM6800E-48X8 unit).
NOTE: After completing system installation and power-up, you must configure the CM6800E and the camera/receiver. Refer to the System
Start-up section.
96 x 16 System PTZ Control Capacity
Main unit:
Expansion unit:
PTZ-A and PTZ-B; 16 receivers each
PTZ-C and PTZ-D; 16 receivers each
VIDEO TO SWITCHER
SHIELDED
TWISTED
PAIR
RECEIVER 16
RECEIVER 2
RECEIVER 1
RS-422
Figure 9. PTZ Control Connections
16
C1528M-G (9/06)
MONITORS
The CM6800E supports eight monitors.
1. Install monitors according to the instructions provided with them.
2. Connect the monitor cables at the appropriate video output BNC receptacles on the back of the CM6800E.
3. Terminate cables at the monitors. If you are looping to other devices, terminate only at the last device.
96 x 16 System Monitor Capacity
Main unit:
Expansion unit:
Monitor 1-8
Monitor 9-16
MONITOR
1
40
MONITOR
2
41
42
43
44
1
2
3
4
45
46
47
48
5
6
7
8
MONITOR
3
MONITOR
4
MONITOR
7
MONITOR
8
ALT
LOOPING
MONITOR
5B
MONITOR
5A
MONITOR
6
Figure 10. Connecting Monitors
C1528M-G (9/06)
17
ALARMS
The CM6800E provides numerous alarm handling options. Refer to the Programming the CM6800E section for a detailed description.
1. Connect wires from the sensors to the respective alarm input points on the connectors at the back of the CM6800E. Each sensor requires
two wires – one wire to the alarm input terminal and a return wire to one of the ground terminals on the connector. The CM6800E supports
eight internal alarms.
Alarm sensors can be either N.O. (normally open) or N.C. (normally closed) contacts. The CM6800E is set to N.O. as a factory default.
2. If your system requires more than eight alarms, connect an ALM2064 unit to the system. Refer to the M Devices (KBD960, ALM2064,
REL2064) section.
96 x 16 System Alarm Capacity
Main unit:
Expansion unit:
Alarms 1-8
Alarms 9-16
ALARM
CONTACT
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
4
8
CONTROL
A T T
+ -
31
32
2
3
4
6
7
8
1
R R T T
- + + -
2
R R B
- +
F
3
1
120/230~
50/60 HZ
25 WATTS
CM6800E-48X8
ALM2064
Figure 11. Connecting Alarms
18
C1528M-G (9/06)
CONNECTING DEVICES THROUGH THE COMMUNICATION PORTS
The CM6800E Matrix Switcher/Controller provides eight communication ports on the rear panel for connecting peripheral components.
Instructions are provided in this section for the most commonly used connections.
NOTE: Connection instructions for other peripheral devices, such as the CM9760-MDA or CM9760-CDU-T, are provided as Pelco Technical Tips.
These Technical Tips are provided on the CM6800 Resource CD (which is shipped with the matrix switcher) and they are also available on the
Pelco Internet page (www.pelco.com). Connection instructions for compatible products, such as PelcoNet transmission systems and the VMX300
are provided in the appropriate product installation manual.
Figure 12. Communication Port Inputs
Table B. Communication Port Devices and Wiring
Port Input Type
Wiring
Pin-Outs
Default Device
Programmable to Other Device(s)
1
DB9 or RJ-45
RS-232
2
3
5
Rx
Tx
Ground
PC Setup – CM6800MGR
program
ASCII device
2
RJ-45
RS-232
1
5
8
Rx
Ground
Tx
CM6800E-48X8 for a
“bay-to-bay” expansion to a
96x16 system
ASCII device (only when used in a
48 x 8 configuration)
3
RJ-45
RS-485
1
2
5
7
8
Rx+
RxGround
TxTx+
M devices — ALM2064,
REL2064, KBD960
No
4
RJ-45
RS-485
1
2
5
7
8
Rx+
RxGround
TxTx+
Genex multiplexer
CM9760-MDA, ASCII
5 & 6 RJ-45
RS-485 plus power 1
2
3
4
5
7
8
Rx+
Keyboard (direct powered) –
RxKBD100, KBD200A, & KBD300A
KBD power (12V)
KBD Ground
Ground
TxTx+
No
(Continued on next page)
C1528M-G (9/06)
19
Table B. Communication Port Devices and Wiring (Continued)
Port Input Type
7
RJ-45
Wiring
Pin-Outs
Default Device
Programmable to Other Device(s)
RS-485 or RS-232
RS-485 Pin-Outs:
1 Rx+
2 Rx5 Ground
7 Tx8 Tx+
ASCII device
CM9760-MDA, Satellite, keyboards
(KBD100/200A/300A)
ASCII device
CM9760-MDA, keyboards (KBD100/
200A/300A)
RS-232 Pin-Outs:
1 Rx
5 Ground
8 Tx
8
RJ-45
RS-485 or RS-232
RS-485 Pin-Outs:
1 Rx+
2 Rx5 Ground
7 Tx8 Tx+
RS-232 Pin-Outs:
1 Rx
5 Ground
8 Tx
Table C. Default Port Settings
Port
Default Settings
1
MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit
2
BAY-TO-BAY, RS-232, 115000 baud, no parity, 8 data bits, 1 stop bit
3
M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit
4
MUX-GENEX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit
5, 6
KBD300, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit
7, 8
ASCII, RS-485, 9600 baud, no parity, 8 data bits, 1 stop bit
NOTE: Refer to the Programming the CM6800E section for instructions on changing Port settings.
20
C1528M-G (9/06)
PC DB9 CONNECTION
COM 1
PC SETUP (RS-232)
USE DB9 CONNECTION
OR ALTERNATE RJ-45 CONNECTION
BOTH CANNOT BE USED SIMULTANEOUSLY
RS-232 NULL MODEM CABLE
NOTE: TOTAL NUMBER OF
KBD100/200A/300A SERIES
KEYBOARDS CONNECTED
TO THE CM6800 CANNOT
EXCEED 16
COM 5 & 6
LOCAL KEYBOARDS (RS-485)
KBD100/200A/300A SERIES
MAX # OF DEVICES = 8
010101
1 2 3 4 5 6 7 8
16
PC RJ-45 CONNECTION
1
5
2
6
CONTROL
A T T
+ -
COM 2
(RS232)
BAY TO BAY CMM6800-48X8E
OR ASCII CONTROL
31
32
2
3
4
6
7
8
3
7
4
8
R R T T
- + + -
1
R R B
- +
F
3
2
1
120/230~
50/60 HZ
25 WATTS
COM 4
GENEX (RS-485)
ALSO PROGRAMMABLE FOR ASCII
OR CM9760-MDA MAX # OF DEVICES = 8
4
5
3
6
2
1
COM 3
M DEVICES (RS-485)
MAX # OF DEVICES = 6
MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)
4
4
5
5
3
3
6
6
7
5
4
5
4
5
4
5
3
6
3
6
3
6
COM 7 & 8
(RS-485 OR RS-232)
PROGRAMMABLE FOR KBD100/200A/300A SERIES
ASCII, SATELLITE (COM 7 ONLY), OR CM9760-MDA
4
5
4
5
4
5
3
6
3
6
3
6
7
8
STRAIGHT
CABLES
12V50 HZ
TRANSFORMER
ALM2064
NUMBER SUPPORTED = 4
64 ALARMS X 4 = 256 ALARMS
CM9505UPS
POWER SUPPLY
KBD960
REL2064
NUMBER SUPPORTED = 4
64 RELAYS X 4 = 256
KBD960
NUMBER SUPPORTED = 2
Figure 13. CM6800E Communication Port Connections and Options
C1528M-G (9/06)
21
KBD100, KBD200A, AND KBD300A SERIES KEYBOARDS
You can connect up to eight KBD100/200A/300A Series keyboards to any of the following ports:
•
COM 5 (1 direct-powered keyboard or up to 8 remotely connected keyboards)
•
COM 6 (1 direct-powered keyboard or up to 8 remotely connected keyboards)
•
COM 7 (up to 8 remotely connected keyboards)
•
COM 8 (up to 8 remotely connected keyboards)
The total number of KBD100/200A/300A Series keyboards connected to the CM6800E cannot exceed 16.
KBD100, KBD200A, and KBD300A: Direct-Powered Keyboards
Use COM 5 and 6 (Serial Ports 5 and 6) for direct-powered local keyboards. Each port can power one KBD100/200A/300A Series keyboard.
If you are connecting more than one keyboard to COM 5 or 6, a KBDKIT(-X) is required for each keyboard. Refer to the KBD100, KBD200A, and
KBD300A: Remote Keyboards section.
1. Using the 25-foot (7.62 m) straight data cable supplied with the keyboard, plug one end into the RJ-45 connector on the rear of the
keyboard.
NOTE: If distance between CM6800E and keyboard exceeds 25 feet, use KBDKIT(-X).
DEFAULT (ADDRESS 0) DIP SWITCH SETTINGS
(SHIPPED FROM FACTORY)
DIP SWITCHES 1-8 OFF
KBD300A
Figure 14. Data Cable Plugged into Local Keyboard
2. Plug the other end of the data cable into either COM 5 or 6 on the CM6800E.
KBD100, KBD200A, KBD300A
KBD100, KBD200A, KBD300A
010101
CM6800E-48X8
COM 5&6
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
4
8
CONTROL
A T T
+ -
31
32
2
3
4
6
7
8
1
R R T T
- + + -
2
R R B
- +
F
3
1
1
2
3
4
5
6
7
8
Rx+
RxKBD 12V
KBD GROUND
GROUND
NC
TxTx+
KBD100, 200A, 300A
RJ-45 PIN-OUTS
1 Tx+
2 Tx3 12V
4 12V
5 GROUND
6 NC
7 Rx8 Rx+
120/230~
50/60 HZ
25 WATTS
Figure 15. Data Cables Plugged into COM 5 and 6
22
C1528M-G (9/06)
3. Set the keyboard DIP switches for the desired address for the local keyboard (refer to Figure 12 and Table D).
Table D. Keyboard Addresses: KBD100/200A/300A Series Keyboards
Keyboard
Address
Switch Settings
1
2
3
4
1
0
OFF
OFF
OFF
OFF
2
1
ON
OFF
OFF
OFF
3
2
OFF
ON
OFF
OFF
4
3
ON
ON
OFF
OFF
5
4
OFF
OFF
ON
OFF
6
5
ON
OFF
ON
OFF
7
6
OFF
ON
ON
OFF
8
7
ON
ON
ON
OFF
Table E. Switch Settings—KBD200A/300A Keyboards Only
Keyboard
Switch
5
6
7
8
KBD200A
OFF
OFF
OFF (NOT USED)
OFF
KBD300A
OFF
ON or OFF*
OFF (NOT USED)
OFF
*Switch 6 enables/disables turbo pan (can be switched while keyboard is on).
C1528M-G (9/06)
23
KBD100, KBD200A, and KBD300A: Remote Keyboards
Use COM 5, 6, 7, or 8 for remote keyboard connections. Each port can support up to eight KBD100/200A/300A Series keyboards. Do not exceed
a total capacity of 16 keyboards connected to the CM6800E.
NOTE: A KBDKIT or KBDKIT-X is required to connect remote keyboards. The KBDKIT(-X) consists of two RJ-45 wall blocks and one transformer.
Use one wall block for each keyboard.
If using COM 7 or 8, you will need to change the settings (the default setting is for an ASCII device.) Refer to the Programming the CM6800E
section for instructions.
1. Select a suitable location for each keyboard and wall block. Wall blocks must be within 6 feet (1.8 m) of a suitable electrical outlet. Do not
mount the wall blocks yet.
2. Connect each keyboard to a wall block, using the keyboard data cable supplied with the keyboard.
3. Remove the wall block covers and wire the connections between each wall block. Connect to a final wall block (which will be connected to
the CM6800E).
Communication to the keyboards is RS-485. Pelco recommends using shielded twisted pairs cable that meets or exceeds the basic
requirements for EIA RS-485 applications.
4. At each wall block, wire the KBDKIT(-X) transformer to pins 3 and 4. Polarity is unimportant.
5. Replace the cover on the wall block. Secure the wall block to a suitable surface. A double-sided sticky pad is provided to mount the wall
block.
6. Set the address switches for each keyboard according to Table D.
7. Connect the final wall block to COM 5, 6, 7, or 8 on the CM6800E, using a straight data cable (supplied with the CM6800E).
010101
1
5
2
6
CM6800E-48X8
COM 7 & 8
RJ-45 PIN-OUTS
1 Rx+
2 Rx3 12V
4 12V
5 GROUND
6 NC
7 Tx8 Tx+
1 2 3 4 5 6 7 8
16
CONTROL
31
2
6
3
7
32
3
7
4
4
A T T
+ -
8
R R T T
- + + -
1
2
R R B
- +
F
3
1
8
KBD100, 200A, 300A
RJ-45 PIN-OUTS
1 Tx+
2 Tx3 NC
4 NC
5 GROUND
6 NC
7 Rx8 Rx+
120/230~
50/60 HZ
25 WATTS
WALL BLOCK
4
5
3
6
3
6
3
6
3
6
2
7
2
7
2
7
2
7
1
8
1
8
1
8
1
8
4
5
4
5
KBD100
4
5
KBDKIT(-X)
KBD300A
KBD200A
REMOTE KEYBOARDS
Figure 16. Remote Keyboards
24
C1528M-G (9/06)
M DEVICES (KBD960, ALM2064, REL2064)
M protocol devices (KBD960/KBR960 keyboards, ALM2064 Alarm Interface Units, and REL2064 Relay Interface Units) can be connected to
COM 3 on the CM6800E.
If only one device is to be connected to COM 3, use the instructions for that device in the following sections.
If more than one device is to be connected to COM 3, refer to the Multiple M Devices section.
Connect M devices to the CM6800E with straight cables. Four straight cables and one reversed cable are supplied with the CM6800E (save the
reversed cable for connecting a Genex Multiplexer, if applicable).
M Devices Addressing
Each M device connected to the CM6800E must have a unique local address within a range of 1-16. Use the hardware DIP switches to set the
appropriate ALM2064 and REL2064 local addresses. Specify the appropriate KBD960/KBR960 local address through the keyboard Setup Mode
after you complete the system installation (refer to the System Start-up section).
For use with the CM6800E, Pelco recommends numbering M devices in a sequential order. In a sample application, with two of each M device,
you might assign local addresses as follows:
M device local addresses:
KBD960/KBR960:
REL2064:
ALM2064:
Default
1
1
1
Recommended for CM6800E
1, 2
3, 4
5, 6
NOTE: To use the CM6800 system access or keyboard priority features, you must assign KBD960/KBR960 keyboards an address within a range
of 1-8
COMPARED "COLOR RUN"
IS IN OPPOSITE DIRECTION
COMPARED "COLOR RUN"
IS IN SAME DIRECTION
BROWN
BROWN
BROWN
STRAIGHT
CABLE
BROWN
REVERSED
CABLE
Figure 17. RJ-45 Cable Types
C1528M-G (9/06)
25
Connecting a Single KBD960/KBR960 Keyboard
To connect a single KBD960/KBR960 Keyboard to the CM6800E:
1. Connect the keyboard to the CM9505UPS using the straight cable supplied with the keyboard.
2. Connect the CM9505UPS to COM 3 on the CM6800E using the 6-foot (1.8 m) straight data cable supplied with the CM6800E.
NOTE: After completing system installation and power-up, you must configure the KBD960/KBR960 settings. Refer to the System Start-up
section.
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
CONTROL
31
32
2
3
4
6
7
8
4
A T T
+ -
8
1
R R T T
- + + -
2
R R B
- +
F
3
COM 3 DEFAULT SETTINGS:
M, RS-485, 19200 BAUD,
NO PARITY, 8 DATA BITS,
1 STOP BIT
1
120/230~
50/60 HZ
25 WATTS
CABLE CAN BE STRAIGHT
(SUPPLIED) OR REVERSED
CM9505UPS
RS-485
CM6800-48X8E COM 3
RJ-45 PIN-OUTS
1
2
3
4
5
6
7
8
Rx+
RxNC
NC
GROUND
NC
TxTx+
KBD960
RJ-45 PIN-OUTS
1
2
3
4
5
6
7
8
STRAIGHT CABLE
(SUPPLIED)
Tx+
Tx-
RxRx+
KBD960
Figure 18. Connecting a KBD960/KBR960 to the CM6800E
26
C1528M-G (9/06)
Connecting a Single ALM2064 Alarm Interface Unit
To connect a single ALM2064 Alarm Interface Unit:
1. Connect the ALM2064 OUT port to COM 3 on the CM6800E using the 6-foot (1.8 m) straight data cable supplied with the CM6800E.
2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default address setting is 1). Refer to the ALM2064 Alarm
Interface Unit Installation/Operation Manual for instructions.
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
CONTROL
A T T
+ -
31
32
2
3
4
6
7
8
3
7
4
8
1
R R T T
- + + -
2
R R B
- +
F
3
CM6800E-48X8 COM 3
DEFAULT SETTINGS:
M, RS-485, 19200 BAUD,
NO PARITY, 8 DATA BITS,
1 STOP BIT
1
120/230~
50/60 HZ
25 WATTS
CM6800 COM 3
RJ-45 PIN-OUTS
1
2
3
4
5
6
7
8
Rx+
RxNC
NC
GROUND
NC
TxTx+
ALM2064
RJ-45 PIN-OUTS
1
2
3
4
5
6
7
8
Tx+
Tx-
RxRx+
CM6800 COM 3
RJ-45 PIN-OUTS
STRAIGHT CABLE
(SUPPLIED)
RS-485
ALM2064
CONNECT THROUGH
THE "OUT"PORT
Figure 19. Connecting a Single ALM2064 Alarm Interface Unit
C1528M-G (9/06)
27
Connecting a Single REL2064 Relay Interface Unit
To connect a single REL2064 Relay Interface Unit:
1. Connect the REL2064 OUT port to COM 3 on the CM6800E using the 6-foot (1.8 m) straight data cable supplied with the CM6800E.
2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default address setting is 1). Refer to the REL2064 Relay
Interface Unit Installation/Operation Manual for instructions.
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
CONTROL
A T T
+ -
31
32
2
3
4
6
7
8
3
7
4
8
1
R R T T
- + + -
2
R R B
- +
F
3
CM6800E-48X8 COM 3
DEFAULT SETTINGS:
M, RS-485, 19200 BAUD,
NO PARITY, 8 DATA BITS,
1 STOP BIT
1
120/230~
50/60 HZ
25 WATTS
CM6800 COM 3
RJ-45 PIN-OUTS
Rx+
RxNC
NC
GROUND
NC
TxTx+
STRAIGHT CABLE
(SUPPLIED)
REL2064
RJ-45 PIN-OUTS
1
2
3
4
5
6
7
8
Tx+
Tx-
RxRx+
REL2064
RS-485
CONNECT THROUGH
THE "OUT" PORT
Figure 20. Connecting a Single REL2064 Relay Interface Unit
28
C1528M-G (9/06)
Multiple M Devices
Multiple M devices (KBD960/KBR960, ALM2064, and REL2064) can be connected to COM 3 on the CM6800E, either as local devices or remote
devices (when connecting two KBD960/KBR960 keyboards to the CM6800E, you must use a remote connection).
Multiple M Devices: Local Connection
1. If you are connecting a KBD960/KBR960, connect it to the CM9505UPS with the straight cable supplied with the keyboard. Then connect
the CM9505UPS to the IN port on the next unit (either the ALM2064 or the REL2064) with a 6-foot (1.8 m) straight cable (supplied with the
CM6800E).
2. Connect each ALM2064 and REL2064 unit to the next unit with a 6-foot (1.8 m) straight cable (supplied with the CM6800E) from the OUT
port to the IN port on the next unit. You can connect a maximum of four ALM2064 units and four REL2064 units to the CM6800E.
3. Connect the last unit to the CM6800E with a 6-foot (1.8 m) straight cable (supplied with the CM6800E) from the OUT port to COM 3 on the
CM6800E.
010101
CM6800E-48X8 COM 3 DEFAULT SETTINGS:
M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT
MAXIMUM DISTANCE FROM CM6800 = 3,490 FT (1,200 M)
USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR;
16pF PER FT (pF = PICOFARADS)
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
4
8
CONTROL
CM6800E-48X8 COM 3
RJ-45 PIN-OUTS
1 Rx+
F
3
1
2
2 Rx3
1
4
5 GND
6
120/230~
50/60 HZ
25 WATTS
7 Tx8 Tx+
STRAIGHT CABLE
USE STRAIGHT CABLES
(SUPPLIED)
(SUPPLIED) FOR ALL CONNECTIONS
A T T
+ -
31
32
2
3
4
6
7
8
STRAIGHT CABLE
(SUPPLIED)
R R T T
- + + -
R R B
- +
RS-485
CM9505UPS
STRAIGHT CABLE
(SUPPLIED)
ALM2064
ALM2064
RJ-45 PIN-OUTS
1 Tx+
2 Tx3
4
5
6
7 Rx8 Rx+
KBD960
REL2064
REL2064
RJ-45 PIN-OUTS
1 Tx+
2 Tx3
4
5
6
7 Rx8 \Rx+
KBD960
RJ-45 PIN-OUTS
1 Tx+
2 Tx3
4
5
6
7 Rx8 Rx+
Figure 21. Connecting Multiple M Devices – Local Connection
C1528M-G (9/06)
29
Multiple M Devices: Remote Connection
Use a remote connection when the distance from the CM6800E is greater than 6-feet (1.8 m).
1. Connect each ALM2064 and REL2064 unit to a wall block with a 6-foot (1.8 m) straight cable (supplied with the CM6800E). You can connect
a maximum of four ALM2064 units and four REL2064 units to the CM6800E.
2. If you are connecting a KBD960, connect it to the CM9505UPS with the straight cable supplied with the keyboard. Then connect the
CM9505UPS to a wall block with a 6-foot (1.8 m) straight cable (supplied with the CM6800E). You can connect a maximum of two KBD960
keyboards to the CM6800E.
3. Connect the wall blocks to a final wall block. If additional wall blocks are needed, order part number CON12J008Z03G0Z.
4. Connect the terminal wall block to COM 3 on the CM6800E using a 6-foot (1.8 m) straight cable (supplied with the CM6800E).
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
4
8
CM6800E-48X8 COM 3
DEFAULT SETTINGS:
M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT
MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)
USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR, 16pF PER FT
(pF = PICOFARADS)
CONTROL
31
32
2
3
4
6
7
8
A T T
+ -
1
R R T T
- + + -
2
R R B
- +
F
3
1
120/230~
50/60 HZ
25 WATTS
CM6800E-48X8 COM 3
RJ-45 PIN-OUTS
1 Rx+
2 RX3
4
5 GND
6
7 Tx8 Tx+
STRAIGHT CABLE
(SUPPLIED)
RS-485
STRAIGHT CABLE
(SUPPLIED)
ALM2064
KBD960
REL2064
STRAIGHT CABLE
TO CM9505PS
(SUPPLIED)
KBD960
RJ-45 PIN-OUTS
1 Tx+
2 TX3
4
5
6
7 Rx8 Rx+
CONNECT THROUGH
THE "OUT" PORT
ALM2064
RJ-45 PIN-OUTS
1 Tx+
2 TX3
4
5
6
7 Rx8 Rx+
CONNECT THROUGH
THE "OUT" PORT
REL2064
RJ-45 PIN-OUTS
1 Tx+
2 TX3
4
5
6
7 Rx8 Rx+
Figure 22. Connecting Multiple M Devices – Remote Connection
30
C1528M-G (9/06)
CONNECTING A PC
The CM6800E provides PC-based setup and programming software that facilitates complete switcher programming and configuration. Refer to
the CM6800-MGR Quick Start Guide for instructions on using the software.
Connect a PC to the CM6800E to access the CM6800-MGR software or to download upgrades to the software. You can connect a PC to the
CM6800E through either a DB9 port or an RJ-45 port. You cannot use both ports simultaneously.
1. Using a null modem cable (user-supplied), plug one end into the DB9 COM 1 port on the PC. (To use a PC port other than COM 1, refer to the
CM6800-MGR Installation/Operation Manual.)
2. Plug the other end of the cable into the DB9 COM 1 port of the CM6800E.
NULL MODEM CABLE
PIN 1
PIN 6
PIN 5
CM6800 COM 1
DB9 PIN-OUTS
PC COM 1
DB9 PIN-OUTS
PIN 2 = RX IN
PIN 3 = TX OUT
PIN 5 = GND
PIN 2 = RX IN
PIN 3 = TX OUT
PIN 5 = GND
PIN 9
Figure 23. PC Connection to DB9 Port
OR
1. Using a modified null modem cable (user-supplied), connect the DB9 COM 1 port on the PC to an RJ-45 wall block (supplied with the
CM6800E Matrix Switcher).
The modified null modem cable should be cut at one end, so that you can connect the wires directly to the wall block pins.
2. Using a 6-foot (1.8 m) data cable (supplied with the CM6800E Matrix Switcher), connect the wall block to the RJ-45 COM 1 port of the
CM6800E.
CM6800 COM 1
CM6800 COM 1
RJ-45 PIN-OUTS
PC COM 1
DB9 PIN-OUTS
PIN 1 = RX IN
PIN 5 = GND
PIN 8 = TX OUT
PIN 2 = RX IN
PIN 3 = TX OUT
PIN 5 = GND
PC COM 1
2
3
4
7
6
5
RJ-45 WALL BLOCK
AND STRAIGHT CABLE
SUPPLIED WITH CM6800
MODIFIED NULL MODEM CABLE
(USER-SUPPLIED)
Figure 24. PC Connection to RJ-45 Port
C1528M-G (9/06)
31
CONNECTING GENEX MULTIPLEXERS
Use COM 4 to connect up to eight Genex Multiplexers to the CM6800E.
1. Connect the COM IN port of the multiplexer to COM 4 on the CM6800E, using the 6-foot (1.8 m) reversed data cable supplied with the
CM6800E.
One reversed cable and four straight cables are supplied with the CM6800E. Use the reversed cable for connecting the Genex multiplexer
to the CM6800E.
A straight data cable is supplied with the Genex multiplexer. Use this cable for connecting a second Genex multiplexer to the first
multiplexer, if necessary.
2. Connect the MAIN monitor output from the multiplexer to any of the 48 camera inputs on the CM6800E.
3. Connect cameras to the multiplexer and then loop them to the CM6800E. Refer to the MX4000 Genex Series Simplex and Duplex
Multiplexers Installation/Operation Manual for detailed camera connection instructions. Terminate the video loop at the CM6800E.
4. If required, you can connect a total of eight Genex multiplexers through COM 4. Daisy-chain the multiplexers by connecting a straight data
cable from the COM OUT port on the first multiplexer to the COM IN port on the second multiplexer; connect the COM OUT port on the
second multiplexer to the COM IN port on the third multiplexer. Continue to the eighth multiplexer, if necessary.
Refer to the System Start-up section for additional configuration steps required when using a Genex Multiplexer.
010101
1 2 3 4 5 6 7 8
HZ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
75
1
5
2
6
CONTROL
A T T
+ -
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
41
42
43
44
1
2
3
4
45
46
47
48
5
6
7
8
3
7
4
8
1
R R T T
- + + -
2
R R B
- +
F
3
1
33
34
35
36
37
38
39
40
120/230~
50/60 HZ
25 WATTS
ALT
REVERSED CABLE
SPOT
MAIN
VCR
OUT
AUX
IN
IN
OUT
1 2 3 4 5 6 7 8
SVHS
SVHS
COM
N NH
OCC S
ALARMS
GENEX MULTIPLEXER
9 10 1112 1314 15 16
110-240V 50/60 Hz
MONITOR SIGNAL OUT
STRAIGHT CABLE
SPOT
MAIN
VCR
OUT
AUX
IN
IN
OUT
1 2 3 4 5 6 7 8
SVHS
SVHS
COM
N NH
OCC S
ALARMS
GENEX MULTIPLEXER
9 10 1112 1314 15 16
110-240V 50/60 Hz
STRAIGHT CABLE
SPOT
MAIN
VCR
OUT
AUX
SVHS
IN
IN
SVHS
COM
OUT
N NH
OCC S
ALARMS
1 2 3 4 5 6 7 8
9 10 1112 1314 15 16
GENEX MULTIPLEXER
GENEX MULTIPLEXERS-8 MAXIMUM
110-240V 50/60 Hz
GENEX MULTIPLEXER
RJ-45 PIN-OUTS
Rx+ 1
Rx- 2
12VAC (OUT) 3
12VAC (OUT) 4
GROUND 5
NC 6
Tx- 7
Tx+ 8
CM6800E-48X8 COM 4
RJ-45 PIN-OUTS
1 Rx+
2 Rx3 NC
4 NC
5 GROUND
6 NC
7 Tx8 Tx+
Figure 25. Connecting Genex Multiplexers
32
C1528M-G (9/06)
LOCAL AUXILIARIES
The CM6800E provides three local auxiliary (AUX) outputs on the rear panel for controlling VCRs, printers, and other devices. These outputs can
be activated directly from a keyboard by using the F1, F2, and F3 function keys, or they can be activated by an alarm (determined by
programming). Both relay contacts and TTL outputs are used.
In addition, you can connect up to four REL2064 Relay Interface Units to the CM6800E. Note that since operation of the three internal auxiliary
relays on the CM6800E will also operate the first three relays on the external unit, the maximum capacity of the system may be limited to 256
auxiliaries (depending on how you number the external relays). Refer to the Connecting a Single REL2064 Relay Interface Unit section for
connection instructions.
96 x 16 System Auxiliary Capacity
Main unit:
Expansion Unit:
AUX 1-3
AUX 4-6
Connecting Relay Contacts – AUX 1 and 2
AUX 1 and 2 are dry contact relay outputs. Terminal connections are provided for both normally open (N.O.) and normally closed (N.C.) contacts.
Refer to Figure 26 for wiring details. Note that this figure shows the wiring for a normally open contact. For a normally closed contact, move the
wire from the N.O terminal to the N.C. terminal.
Do not exceed the voltage and current ratings for the relay contacts.
You will need to provide an external power source to operate your device. In most cases you will also need an external current limiting resistor.
The formula for calculating the resistor value is given in Figure 26.
CONTROL
12-PIN PLUG-IN
CONNECTOR
AUX 1 RELAY
CONTACT RATINGS
CURRENT @ VOLTAGE
1A
0.3A
0.5A
EXTERNAL
DEVICE
30 VDC
110 VDC
125 VDC
R
+VPS
I
V
R
+VPS
-VPS
=
=
=
=
OPERATING CURRENT OF THE EXTERNAL DEVICE (MUST NOT EXCEED AUX 1 CURRENT RATING.)
RATED OPERATING VOLTAGE OF THE EXTERNAL DEVICE.
CURRENT LIMITING RESISTOR.
VOLTAGE OF THE EXTERNAL POWER SOURCE (MUST NOT EXCEED VOLTAGE RATING FOR THE
ASSOCIATED CURRENT). VPS CAN BE AC OR DC.
-VPS = NEGATIVE, COMMON OR GROUND TERMINAL OF EXTERNAL POWER SOURCE (AC OR DC).
FORMULAS FOR R VALUES
R (OHMS) = VPS-V
I
P (WATTS) = (I ) X R
Figure 26. Wiring the AUX 1 and 2 (Relay) Outputs
C1528M-G (9/06)
33
Connecting the Open Collector Output – F3 (TTL)
F3 is a TTL open collector output. This output provides a path to ground to control the low voltage trigger input on many devices. It can control
higher voltage control inputs via isolation relays. Refer to Figure 27 for wiring details.
Do not exceed the voltage and current ratings for the TTL output.
An external pull-up resistor is usually necessary. The formula for calculating the resistor value is given in Figure 26.
CONTROL
+VDC
R= +VDC
25 mA
R
12-PIN PLUG-IN
CONNECTOR
INPUT
FROM VIDEO OUTPUT
LOOPED TO MONITOR
DEVICE EXAMPLE: VIDEO PRINTER
+VDC = VOLTAGE OF THE EXTERNAL POWER SOURCE.
NOTE: +VDC SHOULD BE 5V OR GREATER, BUT NOT
EXCEED 15V OR TE MAXIMUM RATED OUTPUT
VOLTAGE FOR THE DEVICE INPUT. +VDC CAN
ONLY BE DC.
Figure 27. Wiring the F3 (TTL) Output
34
C1528M-G (9/06)
CONNECTING A 96 X 16 SYSTEM
1. Install each CM6800E-48X8 unit and connect appropriate devices to each unit. Note that the CM6800E-48X8 expansion unit must be
installed within three feet of the CM6800E-48X8 main unit.
NOTE: If you expand a 48 x 8 system to a 96 x 16 system, you must verify that each CM6800E-48X8 unit contains the same level of
switcher software. Refer to Upgrade the CM6800 Switcher Software in the Appendix. If you have previously used the CM6800-MGR
software in a 48 x 8 configuration, you must uninstall and then reinstall the software before you can use it in a 96 x 16 configuration. Refer
to the CM6800-MGR Installation/Operation manual, or the CM6800-MGR online help for instructions.
Note that keyboards, Genex multiplexers, and other peripheral devices can only be connected to the main unit. The expansion unit can only
support cameras, PTZ receivers, monitors, local alarms, and local relays. Refer to the sample CM6800E 96 x 16 system shown in Figure 2.
2. Connect the CM6800E-48X8 expansion unit to the CM6800E-48X8 main unit.
In the following steps, use the cables and clips provided with the CM6800E-KIT.
a.
Attach the spring clips to the bay-to-bay video port on each
CM6800E-48X8 unit.
b.
Use the 16-channel video ribbon cable to connect the bay-to-bay video port on
the CM6800E-48X8 expansion unit to the bay-to-bay video port on the
CM6800E-48X8 main unit. The “key” on the cable connector must be up. Use
the spring clips to hold the cable connector in place.
c.
Use the reversed data cable to connect port 2 on the CM6800E-48X8
expansion unit to port 2 on the CM6800E-48X8 main unit.
!
CM6800E-48X8 MAIN UNIT
010101
HZ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
HZ
16
75
1
75
1
CM6800E-48X8 EXPANSION UNIT
1 2 3 4 5 6 7 8
3
4
2
010101
5
6
7
8
9
10
11
12
13
14
15
1 2 3 4 5 6 7 8
16
5
1
5
2
6
CONTROL
2
17
33
18
34
19
35
20
36
21
37
22
38
23
39
24
40
25
26
27
28
29
30
31
32
41
42
43
44
1
2
3
4
45
46
47
48
5
6
7
8
ALT
CONTROL
6
3
7 17
4
8
18
A T T
+ -
19
R R T T
- + + -
20
1
33
34
1
35
21
22
23
24
F
3
2
36
R R B
- +
37
38
120/230~
50/60 HZ
25 WATTS
39
40
25
26
27
28
29
30
31
32
41
42
43
44
1
2
3
4
45
46
47
48
5
6
7
8
ALT
3
7
4
8
A T T
+ -
1
R R T T
- + + -
2
R R B
- +
F
3
1
120/230~
50/60 HZ
25 WATTS
Figure 28. Data and Video Connections Between CM6800E-48X8 Units
3. After completing system installation and power-up, select 96 x 16 as the System setting in programming mode. Refer to the Programming
the CM6800E section.
C1528M-G (9/06)
35
System Start-up
After completing the system installation, follow the procedure below to start proper system operation. Skip any “system-specific” steps that do
not apply to your system setup.
POWER-UP THE SYSTEM
Plug the CM6800E power cord into a 120/230V, 50/60 Hz power source. Plug in and turn on all devices connected to the CM6800E.
Once the system is powered-up you will see video from camera 1 and the following time/date stamp on all system monitors:
Figure 29. CM6800E Time/Date Stamp on Monitor
The time stamp will be advancing in one-second increments. Wait five seconds before proceeding.
INITIALIZE KEYBOARDS
Specify a monitor for each keyboard after your first power-up or any time power is cycled to the keyboard or the CM6800E.
Always allow five seconds to elapse before specifying a monitor.
1. Enter a number corresponding to the monitor output that is feeding the monitor you are viewing.
2. Press the MON key. The keyboard LED displays the number you entered. This also confirms successful communication between the
keyboard and the CM6800E. If the keyboard LED does not display the monitor number, repeat 1 and 2.
CONFIGURE THE SYSTEM
The CM6800E is shipped from the factory with default programming settings. If the defaults are acceptable, the CM6800E can be operated
without any user programming. However, you may want to program the following basic system settings:
•
Time and date.
•
Camera titles: by default, each camera is titled “CAM #” (# = camera number).
•
Camera video source: Extended Coaxitron protocol receivers can be operated without any programming changes. For other receiver control
protocols, access the Camera programming screen to select the control type for the device connected to each video input.
•
Alarms: The CM6800E is shipped from the factory with the alarm contact enable field set to OFF. To use the alarm features, access the
Alarm programming screens to enable the alarm contact.
In addition, some or all of the following configuration steps may be necessary, depending on your system. Refer to the Programming the
CM6800E section for detailed instructions on programming the CM6800E.
36
C1528M-G (9/06)
COMMUNICATION PORTS
If you are using any communication port for a device not specified by the default setting, you must access the Port programming screen to change
the settings.
Table F. Default Port Settings
Port
Default Settings
COM 1
MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit
COM 2
BAY2BAY, RS-232, 115000 baud, no parity, 8 data bits, 1 stop bit
COM 3
M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit
COM 4
MUX-GENEX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit
COM 5, 6
KBD300, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit
COM 7, 8
ASCII, RS-485, 9600 baud, no parity, 8 data bits, 1 stop bit
PTZ-A (Port 9)
PTZ-P, RS-422, 4800 baud, no parity, 8 data bits, 1 stop bit
PTZ-B (Port 10)
PTZ-P, RS-422, 4800 baud, no parity, 8 data bits, 1 stop bit
96 X 16 SYSTEM SETTINGS
When you connect two CM6800E-48X8 units together in a 96 x 16 system, you must access the System programming screen and change the
setting to 96 x 16. Refer to the Programming the CM6800E section for instructions.
KBD960/KBR960 KEYBOARD
Configure the KBD960/KBR960 settings.
1. Set DIP switch 2 to the ON position.
2. Enter Setup Mode. Set the local address (1-8). (Note: the baud rate is set by default to 19200.) Each M device connected to the CM6800E
must have a unique local address. Refer to the KBD960/KBR960 Keyboard Installation/Operation Manual for detailed setup instructions.
3. Return DIP switch 2 to the OFF position.
4. Press the EXIT icon on the keyboard LCD screen.
GENEX MULTIPLEXER
Access the Camera programming screen and specify MUX control for all cameras connected to the CM6800E through the Genex Multiplexer.
Access the CM6800E Camera programming screen to configure the following camera control options for each camera connected to the CM6800E
through the Genex Multiplexer:
•
CONTROL: MUX
•
PORT ADDRESS: assign the appropriate address. The port address must match the “Unit ID” assigned through the Genex programming
screens.
You must also configure the Genex Multiplexer. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation
Manual for instructions on accessing the Advanced System Setup programming screen. Select the following options:
•
SPOT MONITOR DISPLAY: TRACK MAIN
•
UNIT ID (must match the port address assigned through the CM6800E)
•
COMM. TYPE: SLAVE (each multiplexer connected to the CM6800E must be in slave mode)
C1528M-G (9/06)
37
MONITOR COLOR ADJUSTMENT
Once you have connected all devices and powered the system, use the CM6800E color bars as a reference tool for adjusting the color on each
monitor.
1. Enter 9999.
2. Press the CAM key. Broadcast quality color bars appear on the monitor.
3. Adjust color on each monitor as necessary until the color bars match the following color order on the monitor (for black and white monitors
you can use the color bars to adjust brightness):
Figure 30. CM6800E Color Bars
PROGRAM RESETS
Program presets as necessary for your system. Refer to the appropriate keyboard manual for instructions.
ADDITIONAL PROGRAMMING
Refer to the Programming the CM6800E section for complete instructions on programming the matrix switcher.
38
C1528M-G (9/06)
Programming the CM6800E
The CM6800E is shipped from the factory with default programming settings. If the defaults are acceptable, the CM6800E can be operated
without any user programming. However, you may want to program the following basic system settings:
•
Time and date
•
Camera titles
•
PTZ control via hardwire data connections
•
Alarm contacts
Alarms must be enabled before they are functional.
•
Access
All access is set to YES by factory default.
•
Communication ports
To connect remote keyboards as shown in the Quick Start Guide, change the settings for Port 7 or 8.
Pelco provides two options for programming the CM6800E to your specifications:
•
Password-protected, on-screen programming screens accessible directly from the Matrix Switcher
•
PC-based CM6800-MGR software
Refer to the CM6800-MGR Quick Start Guide for instructions on accessing and using this software to program your system.
NOTE: Pelco strongly recommends uploading your programming settings to the CM6800-MGR to save settings in the event of an
accidental reset.
The CM6800E allows system programming from only one monitor at a time. If programming from the CM6800-MGR is sent to the CM6800E at
the same time that you are programming from a monitor screen, the system will exit the on-screen programming function.
CM6800E PROGRAMMING MODE
1. If you have not already done so, select the monitor (KBD960/KBR960: if the Camera menu appears, press
2. Press the PGM key (or select
PGM
to exit).
on the KBD960/KBR960). The Password screen appears.
Note that on the KBD960/KBR960 you must first select
and
DEF
. Then enter the Define PIN (Default: 1234), and select
MENU
.
NOTE: When using the CM6800E as a satellite device in a CM9760 system, you can access the CM6800E programming screens from the
CM9760-KBD keyboard if you are viewing a camera controlled by the CM6800E. Refer to the Using the CM6800E-48X8 as a Satellite Device in a
9700 System section in the Appendix.
PELCO VIDEO SWITCHER
MODEL CM6800E
PASSWORD TO MAIN MENU
*******
SCRATCHPAD SEQUENCE
MACRO STATUS VIEW
RETURN
Figure 31. CM6800E Password Screen
C1528M-G (9/06)
39
3. At the ******* prompt, enter the DEFAULT PASSWORD: 2899100
The Main Menu appears.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
Figure 32. CM6800E Programming Main Menu
Select Language
If necessary, select the appropriate language.
1. Navigate to the language displayed below the menu options.
2. Scroll through the languages and select the language appropriate for your system.
3. Navigate to the RETURN field and navigate left or right to return to the Main Menu.
Exit Programming Mode
40
KBD100/200A/300A Keyboards
KBD960/KBR960 Keyboards
To return to active video you can:
To return to active video you can:
• Press the PGM key once while in the Main Menu.
• Select
• Press the PGM key twice from anywhere else in the
programming screens.
• Select
screens.
• Navigate to the RETURN field and navigate left or right to return
to the previous screen or menu.
• Navigate to the RETURN field and navigate left or right to return
to the previous screen or menu.
PGM
PGM
once while in the Main Menu.
twice from anywhere else in the programming
C1528M-G (9/06)
NAVIGATE AND SELECT OPTIONS/FIELD ENTRIES IN PROGRAMMING MODE
During programming, a menu appears on the monitor screen. The currently selected field blinks. Use the following keys or joystick on your
keyboard to navigate the programming screens.
Function
Keyboard
Navigate programming screens.
KBD100
Use the sequence and macro keys.
Left
Right
Up
Down
PREV
NEXT
MACRO
HOLD
Right
Up
Down
Right
Up
Down
KBD200A
Use the Pan/Tilt positioning keys.
Left
KBD300A
Use the joystick.
Left
KBD960/KBR960
Use the joystick. (See above icons)
OR
Select the appropriate icon on the KBD960/KBR960 LCD SCREEN.
Left
Access a screen from the Main Menu (or from a submenu).
Right
Up
Down
All Keyboards
1. Navigate down to the desired menu option.
2. Navigate left or right to select the menu option.
OR
1. Using the numerical keypad, enter the number of the menu
option.
2. Press F1 on the KBD100/200A/300A keyboard or select
the KBD960/KBR960 keyboard.
Scroll through options in programming fields.
on
KBD100/200A/300A
Use F1 and F2. Or (KBD300A only) use the joystick to navigate left or
right.
F1
F2
NOTE: The joystick does not scroll options in all fields.
KBD960/KBR960
Select the
right.
or
icons or use the joystick to navigate left or
NOTE: The joystick does not scroll options in all fields.
C1528M-G (9/06)
41
Function
Keyboard
Select option in a programming field.
All Keyboards
1. Scroll through the options until the appropriate entry appears in
the field.
2. Navigate to the next field or press PGM to exit.
NOTE: On the Monitor and Time & Date screens you must apply the
changes (refer to Time and Date or Monitor Display in this section).
Enter a numerical value in an option field (not available in all fields).
All Keyboards
1. Using the numerical keypad, enter a number within the range of
valid options (example: to enter an internal alarm contact you
must enter a number between 1 and 8).
2. Press F1 on the KBD100/200A/300A keyboard or select
the KBD960/KBR960 keyboard.
Access the HELP screen (Sequences, Macros, and Alarm Group
screens).
on
All Keyboards
1. Navigate to the HELP field.
2. Press F1.
Access the NEXT or PREVIOUS page of a list (not available on every
screen).
All Keyboards
1. Navigate to the NEXT or PREVIOUS field.
2. Press F1.
Exit a screen.
All Keyboards
1. Navigate to the RETURN field.
2. Navigate left or right.
OR
Press the PGM key to return to the previous screen or menu.
42
C1528M-G (9/06)
ACCESS
RESTRICT SYSTEM ACCESS
In the CM6800E, system access is set to Yes (unrestricted) by default. The system supports the following ways to restrict system access:
Keyboard to Monitor: Set access to No in order to restrict a keyboard from accessing selected monitors.
Camera to Keyboard: Set access to No in order to restrict a keyboard from calling selected cameras to monitors. Or set access to V (video
viewing only) to permit the viewing of selected cameras while preventing pan and tilt control.
Camera to Monitor:
Set access to No in order to restrict the viewing of selected cameras on selected monitors.
NOTE: To restrict access for keyboards, all keyboard addresses must be within a range from 1-8.
NOTE: If you connect an ASCII keyboard/device to the CM6800E (COM port 1, 2, 4, 7, or 8), you can connect only one keyboard to a port. Specify
access in the first column only (address 1).
CAMERA TO KEYBOARD ACCESS
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
PORT 5
KEYBOARD
ACCESS
1
2
3
4
KEYBOARD TO MONITOR
CAMERA TO KEYBOARD
CAMERA TO MONITOR
SATELITE VIEW
PTZ TIME OUT: ON
RETURN
CAM
0001
0002
0003
0004
0005
0006
0007
0008
0009
0010
0011
0012
0013
0014
0015
0016
1
V
V
V
V
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
2
Y
Y
Y
Y
N
N
N
N
Y
Y
Y
Y
Y
Y
Y
Y
3
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
4
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
NEXT
5
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
6
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
7
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
8
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
PREVIOUS
RETURN
Figure 33. Sample Access Screen
1. Select the COM port number for which you are programming access control.
2. In the Access matrix, configure the specific access allowed for each device.
Keyboard to Monitor
In each monitor row specify the access allowed for each keyboard to control each specific monitor.
Y = Yes; control is allowed
N = No; control is not allowed
Camera to Keyboard
In each camera row specify the access allowed for each keyboard to view and control the specific logical camera number.
Y = Yes; viewing and control is allowed
N = No; viewing and control is not allowed
V = View only; camera can be viewed but not controlled
Camera to Monitor
In each camera row specify the access allowed for each monitor to display the specific logical camera number.
Y = Yes; camera can be viewed
N = No; camera cannot be viewed
SET SATELLITE VIEW ACCESS
The Satellite View option is used only if you use the CM6800E as a satellite switcher in a CM9760 system. Refer to the Configure the CM6800E
as a Satellite Device section.
CHANGE PTZ DELAY
When an operator uses a matrix system keyboard to control a PTZ camera, the CM6800E includes a five-second delay before another operator
can control a PTZ camera. To remove this delay, change the PTZ TIME OUT selection to OFF. (Note that the OFF setting reduces the delay to a halfsecond, which should not be noticeable to the operator.)
C1528M-G (9/06)
43
ALARM PROGRAMMING
Alarmed cameras can be displayed on one or several monitors as part of one or several alarm groups (each monitor can display only one
alarm group).
Before programming alarm settings note the following precautions:
•
Verify that no automated system functions are set to run, such as a macro that would arm or disarm an alarm.
•
Ensure that system operators do not arm or disarm any alarms while you are programming alarm settings.
NOTE: You cannot access the Alarm Contacts screen when an alarm is active. If an alarm is triggered while you are in the CM6800 programming
screens, the system will exit the on-screen programming function and display the alarm on the appropriate monitor(s).
Complete the following steps to program alarms:
1. Program the alarm display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display as a
part of each alarm. Refer to Program Alarm Groups.
2. Program the individual alarm contact. Refer to Program an Internal or External Alarm Contact.
3. Optional: Assign a logical alarm number to the alarm contact. Refer to Assign a Logical Alarm Number.
PROGRAM ALARM GROUPS
Use the Alarm Group screen to configure alarm groups to appear on system monitors.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
ALARM MONITOR GROUP SETUP
ALARM CONTACTS
1
2
3
4
5
MON
A
B
C
D
E
F
G
H
01
02
03
04
05
06
07
08
–
–
–
D
Q
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
S
S
S
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
INTERNAL CONTACT
EXTERNAL CONTACT
VIDEO LOSS
ALARM GROUP
LOGICAL ALARM NUMBER
RETURN
HELP
RETURN
Figure 34. Program Alarm Groups
Specify the display option for each alarm group. Refer to the on-screen Help or to the Alarm Group Display Options section in the Appendix for a
description of each display option.
44
Display Option Entry
Display Option Type
Number of Monitors Displaying Each Alarm Group
B
block build
up to eight (96 x 16 system: up to 16)
D and Q
chronological pair
one display monitor (D), one queue monitor (Q)
M and L
reverse chronological pair
one display monitor (M), one queue monitor (L)
S
Salvo group
from two to eight (96 x 16 system: from two to 16)
C1528M-G (9/06)
PROGRAM AN INTERNAL OR EXTERNAL ALARM CONTACT
Use the Alarm Contact screens to configure alarm inputs. When an alarm is triggered, the logical alarm number, the alarm icon, and the alarm
letter (“I” for internal; “E” for external) appear on monitors programmed through the Alarm Group screen to display the alarm.
INTERNAL ALARM MENU
CONTACT:
ACK TYPE:
TYPE:
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
1
MANUAL
NO
STP
CAM
DWL
CMD
##
AUX
##
1
2
3
4
5
6
7
8
0001
0001
0001
0001
0001
0001
0001
0001
01
00
00
00
00
00
00
00
PRES
––––
––––
––––
––––
––––
––––
––––
13
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
000
000
000
000
000
000
000
000
ALARM CONTACTS
1
2
3
4
5
ENABLE:
OFF
TIME OUT: 10
PRIORITY: 0
INTERNAL CONTACT
EXTERNAL CONTACT
VIDEO LOSS
ALARM GROUP
LOGICAL ALARM NUMBER
A
B
Y
N
GROUP ENABLE
C D E F G
N
N
N
N
N
H
N
RETURN
EXTERNAL ALARM MENU
RETURN
CONTACT:
ACK TYPE:
PRIORITY:
001
MANUAL
0
ENABLE:
OFF
TIME OUT: 10
STP
CAM
DWL
CMD
##
AUX
##
1
2
3
4
5
6
7
8
0001
0001
0001
0001
0001
0001
0001
0001
00
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
00
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
000
000
000
000
000
000
000
000
A
B
N
N
GROUP ENABLE
C D E F G
N
N
N
N
N
H
N
RETURN
Figure 35. Program Internal and External Alarms
1. Select the alarm input number in the CONTACT field.
Internal Alarm screen: Configure any of the eight internal alarm inputs on the CM6800 rear panel. A 96 x 16 system has 16 internal alarm
inputs. Internal inputs are programmable to associate any camera to any input.
External Alarm screen: Configure any of the external alarms. A maximum of four external ALM2064 Alarm Interface Units can be connected
to the CM6800, providing up to 256 external alarm inputs.
2. Select ON in the ENABLE field.
3. In the STP matrix, configure up to eight steps to be triggered as a result of this alarm.
a.
In the CAM field select a camera (use the logical camera number) to be displayed on a system monitor.
b.
In the DWL field, enter the amount of time the camera view is displayed in an alarm sequence; enter a dwell time between 1 and
99 seconds.
c.
Optional: In the CMD field, select a camera operation; if you select a macro, pattern, or preset, enter a valid macro, pattern, or preset
number in the ## field:
MACRO = macro (only the first three steps can be used when selecting a macro; each step must call a macro)
PRES = preset
PATT = pattern
RSCN = random scan
FSCN = frame scan
SSCN = stop scan
In the AUX field, select an auxiliary to be activated.
GON = turn global auxiliary on
GOFF = turn global auxiliary off
CON = turn camera auxiliary on
COFF = turn camera auxiliary off
NOTE: Activate the auxiliaries on the rear panel of the CM6800 by selecting global auxiliary numbers 1, 2, or 3 (in a 96 x 16 system
the expansion unit auxiliaries are activated by global auxiliary numbers 4, 5, and 6). The remaining global auxiliary numbers control
auxiliaries in up to four REL2064 Relay Interface Units.
C1528M-G (9/06)
45
4. In the GROUP ENABLE field, select “Y” under the appropriate group letter to assign the alarm contact to one or more alarm groups. Refer to
the Program Alarm Groups section for information on alarm group display options.
NOTE: Verify that the monitor specified by the alarm group has access to the camera view(s) triggered by this alarm. If an alarm is cued to
a monitor that does not have access to the appropriate cameras, the camera views cannot be monitored.
5. Optional: The remaining alarm contact fields are configured with factory default settings; customize your system as necessary, by
changing the following settings:
ACK TYPE: The alarm clearance type is set to MANUAL by default, requiring an operator to acknowledge an alarm from a system
keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the TIME OUT field.
TYPE:
Internal alarms are set by factory default as N.O. (normally open). Select N.C. for normally closed operation. Set the external
alarm input type through the ALM2064 Alarm Interface Unit.
PRIORITY:
Select 1 for a priority alarm, which appears on system monitors before a non-priority (0) alarm.
PROGRAM A VIDEO LOSS ALARM
Use the Video Loss screen to program the CM6800 to detect video loss from any camera input and indicate the loss through alarm mode – the
logical alarm number, the alarm icon, and a “V” (for video loss) appear on system monitors as specified by alarm group assignment.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
VIDEO LOSS MENU
PHYSICAL INPUT:
ALARM CONTACTS
1
2
3
4
5
INTERNAL CONTACT
EXTERNAL CONTACT
VIDEO LOSS
ALARM GROUP
LOGICAL ALARM NUMBER
ENABLE: OFF
ACK TYPE: MANUAL
TIME OUT: 10
CAMERA 0001
A
B
N
N
GROUP ENABLE
C D E F G
N
N
N
N
N
H
N
RETURN
RETURN
Figure 36. Program Video Loss Alarms
1. Select the PHYSICAL INPUT number; the logical camera number associated with the physical input appears in the CAMERA field.
2. Select ON in the ENABLE field.
3. In the GROUP ENABLE field, select “Y” under the appropriate group letter to assign the alarm contact to one or more alarm groups. Refer to
the Program Alarm Groups section for information on alarm group display options.
4. Optional: The ACK TYPE (alarm clearance type) field is set to MANUAL by default, requiring an operator to acknowledge a video loss
alarm from a system keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the TIME OUT field.
46
C1528M-G (9/06)
ASSIGN A LOGICAL ALARM NUMBER
This procedure is optional.
Each CM6800E alarm type (internal, external, and video loss) has been assigned a series of default logical alarm numbers, which start at 001 and
continue sequentially. Depending on how you use the CM6800E system, the default logical alarm numbers could create a numbering conflict, as
described below.
Logical alarm numbers are used in the following ways:
•
When an alarm is triggered, the logical alarm number, along with the alarm icon and the alarm letter (“I” for internal; “E” for external; “V”
for video) appears on monitors programmed through the Alarm Group screen to display the alarm. Using the default logical alarm numbers
is acceptable in this situation, because the alarm letter indicates what type of alarm is active.
•
If you program the CM6800E to report alarms to an ASCII device, as described in the Ports (Serial/COM Ports) section, then you must assign
unique logical alarm numbers to each alarm type. Otherwise numbering conflicts will occur; for example, an internal alarm numbered 001
would be reported in the same way as an external alarm numbered 001.
•
If you use the CM6800E as a satellite device in the CM9740/CM9760 system, and set the CM6800E to report alarms, then you must assign
each CM6800E alarm a logical alarm number that is unique within the CM9740/CM9760 system (i.e. when used as a satellite device, the
CM6800E shares the same pool of logical alarms numbers as the CM9740/CM9760 system).
To assign new logical alarm numbers, navigate to the Logical Alarm Number menu as shown in Figure 37.
LOGICAL ALARM NUMBER MENU
ALARM CONTACTS
1
2
3
4
5
INTERNAL CONTACT
EXTERNAL CONTACT
VIDEO LOSS
ALARM GROUP
LOGICAL ALARM NUMBER
1 LOGICAL INTERNAL ALARM
2 LOGICAL EXTERNAL ALARM
3 LOGICAL VIDEO LOSS
RETURN
RETURN
LOGICAL INTERNAL ALARM
LOG
0001
0002
0003
0004
0005
0006
0007
0008
PHY
1
2
3
4
5
6
7
8
RETURN
Figure 37. Assign a Logical Alarm Number
C1528M-G (9/06)
47
AUXILIARY OUTPUTS
The three local auxiliary (AUX) outputs on the rear panel of the CM6800E can be operated manually from a system keyboard or automatically in
response to an alarm.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SET AUXILIARY MENU
AUX
1
2
3
MODE
ALM
LAT
MOM
MON
01
02
03
DWL
10
43
20
RETURN
Figure 38. Program Auxiliary Outputs
Latching or Momentary Operation
In the MODE field for each auxiliary, select either LAT or MOM.
Alarm-based Operation
1. In the MODE field for each auxiliary, select ALM.
2. In the MON field, select the monitor the auxiliary will follow.
3. In the DWL field, enter the number of seconds the auxiliary will remain active after there is no longer an alarm displayed on a system
monitor. The alarm is displayed on a monitor until
•
the alarm is acknowledged manually (if MANUAL is selected in the alarm contact ACK TYPE field),
•
the alarm contact times out (if AUTO is selected in the alarm contact ACK TYPE field).
Refer to the ACK TYPE description in Program an Internal or External Alarm Contact.
48
C1528M-G (9/06)
CAMERA PROGRAMMING
Extended Coaxitron protocol receivers can be operated without any programming changes, other than changing the camera title, if necessary.
For other receiver control protocols, you must select the control type for the device connected to each video input.
If necessary, first program logical camera number.
PROGRAM LOGICAL NUMBERS
Default logical numbers start at 0001 and continue sequentially to 0048 (or to 0096 in a 96 x 16 system). To use a different numbering scheme,
program new numbers on the Logical Camera Number screen.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
LOGICAL CAMERA NUMBER MENU
PHY
LOG
PHY
LOG
PHY
LOG
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
0001
0002
0003
0004
0005
0006
0007
0008
0009
0201
0202
0203
0301
0302
0303
0401
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
0402
0403
0404
0405
0500
0501
0502
0503
0504
0505
0601
0602
0603
0604
0605
0032
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
0033
0034
0035
0036
0037
0038
0039
0040
0041
0042
0043
0044
0045
0046
0047
0048
RETURN
Figure 39. Program Logical Camera Numbers
The numbers in the PHY columns are the physical input numbers; each represents an actual BNC input on the rear panel of the CM6800 and
cannot be changed.
In the LOG field for each physical camera input, assign a valid logical number (0001-9998). A valid number is any number from 0001 to 9998 that
has not already been assigned to a physical camera input.
NOTE: If you change a logical number, you cannot control the camera until you select the new logical number from the keyboard.
C1528M-G (9/06)
49
PROGRAM CAMERAS
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
CAMERA 0001
VERTICAL DRIVE: OFF
CONTROL:
EXT COAX
PORT ADDRESS: 01
CAMERA TITLE
CAM 1
SELECT CHARACTER
RETURN
Figure 40. Program Cameras
1. In the CAMERA field, select the logical camera number of the video input to be defined.
2. In the CONTROL field, select the receiver control type.
EXT COAX: Coaxitron extended mode (32-bit)
STD COAX: Coaxitron standard mode (15-bit)
MUX: Genex multiplexer
PTZ-A: RS-422 Control Port A
PTZ-B: RS-422 Control Port B
M-02: Reserved for future use
M-08: Reserved for future use
NOTE: If you select PTZ-A or PTZ-B you must also program Serial Port 9 or 10, as described in the Ports (Serial/COM Ports) section.
A 96 x 16 System includes PTZ-C and PTZ-D (Serial Ports 11 and 12).
3. The PORT ADDRESS field is required for Genex or RS-422 control only.
Genex multiplexer: Select the address of the multiplexer (01-32); this address must match the unit ID specified through multiplexer
programming. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual.
RS-422 cameras: Select the camera/device address for RS-422 control (01-32). The port address must match the address setting
configured through the camera/receiver DIP switch settings.
4. Select the camera title. This title (up to 20 characters) appears on the monitor during real-time camera display.
a.
Navigate to the position in the camera title that you want to change.
b.
Use F1 and F2 to scroll through the camera title characters; once you reach the desired character for that position, navigate to the
next position.
The default title characters are 26 upper case letters and the numbers 0-9. You can add special characters through the Select
Characters screen (described below), or through the CM6800-MGR.
Select Character:
a. Navigate to the SELECT CHARACTER field and navigate left or right. The Select Character screen appears.
b.
To select a character for the first position in the camera title, navigate to the desired character in the font table, and then press F1.
The designated character is displayed in the first position, and the POSITION field increments to position number 02.
Optional: Navigate to the POSITION field and use F1 and F2 to scroll through the camera title position numbers.
c.
Navigate to the desired character in the font table for the next position, and then press F1. Continue until the camera title is complete.
NOTE: You must also configure the camera/receiver. Refer to the appropriate camera/receiver installation manual.
Program Vertical Drive Option (Optional)
Select ON in the VERTICAL DRIVE field to provide the camera with a synchronization pulse via the coax cable. You can use the vertical drive
option with any Pelco camera that supports the Pelco V-Sync feature.
50
C1528M-G (9/06)
EVENT TIMERS
You can automate system operation to activate sequences or macros on specific monitors. Events can be scheduled on a daily or weekly basis, or
on a specific date such as a holiday. If you set more than one timer to start at the same time, the timers will run in the following order of
precedence: weekly, special, daily.
On each event timer screen:
•
Two methods are provided for selecting the event time: scrolling through time values or entering a valid hour and minute.
•
Each timer can activate either a macro or a sequence. Select a value for either the MACRO field or the SEQ field.
•
A macro started by an event timer runs until the last step is completed (unless you specify a loop in the macro).
•
A sequence started by an event timer runs continuously until another sequence or macro begins, or until a system operator selects a
different camera.
EVENT TIMER
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
1
2
3
DAILY TIMER
WEEKLY TIMER
SPECIAL TIMER
DAILY TIMER 01
ENABLE:
TIME:
MACRO
RETURN
MON
1
2
3
4
5
6
7
8
OFF
12:02
00
SEQ
00
00
00
00
00
00
00
00
RETURN
Figure 41. Sample Event Timer Programming
1. Select the timer number.
2. Select ON in the ENABLE field.
3. Set the hour and minute at which the event is to begin (24-hour time) in the TIME field.
4. Special timers only: select the date on which the event is to begin (DD-MMM-YY).
5. Select the event to be activated by the event timer.
To select a macro, select a macro number. For a weekly timer specify the macro in the column under the desired day of the week.
To select a sequence, select a sequence number to run on a specific monitor. For a weekly timer specify the sequence in the column under
the desired day of the week
C1528M-G (9/06)
51
MACROS
Macros simplify operator control by grouping multiple functions into a single command.
MACRO MENU
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
MACRO 01
STP CMD
01
SWT
02
SWT
03
SWT
04
SWT
05
PRES
––––
06
07
––––
08
––––
09
––––
10
––––
11
––––
12
––––
13
––––
14
––––
15
––––
16
––––
17
––––
18
––––
##
000
000
000
000
001
000
000
000
000
000
000
000
000
000
000
000
000
000
NEXT
CAM
0001
0002
0003
0004
0005
0006
0007
0008
0009
0010
0011
0012
0013
0014
0015
0016
0017
0018
HELP
MON DWL
01
01
02
02
03
03
04
04
08
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
00
01
PREVIOUS
RETURN
Figure 42. Macro Screen
MACRO: Select the macro number you want to program.
STP:
Each macro can include up to 72 steps. For each step select entries for the following fields as necessary:
CMD:
Select a command. In addition, enter a valid number in the specified additional field(s); for example, if you select PATT,
enter a pattern number in the Command # field, a camera number in the Camera field, and a monitor number in the Monitor
field. Refer to Table H in the Appendix for a description of each command and the additional fields required for each
command.
##:
If applicable, enter a valid number associated with the command selected.
CAM:
If applicable, enter a logical camera number.
MON:
If applicable, enter a monitor number.
DWL:
If desired, enter a dwell time (1-99 seconds); the dwell time is the period the macro halts before continuing to the next
step. The default dwell time is two seconds.
MACRO STATUS VIEW SCREEN
The Macro Status View screen provides a status view of each system macro (1-64). For each active macro the current status (RUN or HOLD) and
the number of the next macro step is displayed. If a macro is not running, the status is IDLE and the step number is 00.
A system operator can display the Macro Status View screen without entering password- protected programming screens.
PELCO VIDEO SWITCHER
MODEL CM6800E
PASSWORD TO MAIN MENU
*******
SCRATCHPAD SEQUENCE
MACRO STATUS VIEW
RETURN
MAC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
STATUS
RUN
IDLE
HOLD
IDLE
RUN
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
IDLE
NEXT
MACRO STATUS
STEP
MAC
STATUS
STEP
01
17
HOLD
00
09
18
RUN
22
23
19
IDLE
00
00
20
IDLE
00
00
21
IDLE
00
00
22
IDLE
00
00
23
IDLE
00
00
24
IDLE
00
00
25
IDLE
00
00
00
26
IDLE
00
00
27
IDLE
00
00
28
IDLE
00
00
29
IDLE
00
00
30
IDLE
00
00
31
IDLE
00
00
32
IDLE
REFRESH
PREVIOUS
EXIT
Figure 43. Macro Status View Screen
52
C1528M-G (9/06)
MONITOR DISPLAY
Use the Monitor screen to adjust monitor display settings for your system. You can adjust settings for the current monitor only (CURRENT) or for
all system monitors (ALL).
MONITOR CURRENT
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
CAMERA NUMBER:
CAMERA TITLE:
R/X TYPE:
MON/ALM NUMBER:
MON/ALM STATUS:
TIME:
DATE:
BRIGHTNESS
ON
ON
ON
ON
ON
ON
ON
8
POSITION DISPLAY
SET ALL
RETURN
Figure 44. Monitor Screen
MONITOR:
Select CURRENT to program the monitor display for the monitor you are currently operating or ALL for all monitors
connected to the CM6800E.
If you select ALL, you must navigate left or right in the SET ALL field to apply programming changes (refer to the SET ALL
field description).
CAMERA NUMBER:
Enable (ON) or disable (OFF) on-screen display of the logical camera
number.
0001
0001
E
CAM 1
01-JAN-01 01:01:01
CAMERA TITLE:
Enable (ON) or disable (OFF) on-screen display of the camera title
(maximum of 20 alphanumeric characters).
0001
0001
E
CAM 1
01-JAN-01 01:01:01
R/X TYPE:
Enable (ON) or disable (OFF) on-screen display of the camera control type.
The letter displayed on the monitor reflects the receiver control type
selected in the CONTROL field on the Camera screen.
0001
0001
E
CAM 1
01-JAN-01 01:01:01
0001
0001
E
CAM 1
01-JAN-01 01:01:01
R/X TYPE DISPLAY VALUES:
E = Coaxitron extended mode (32-bit)
S = Coaxitron standard mode (15-bit)
M = Genex multiplexer
P = PTZ-P (RS-422 through Control Port PTZ-A or PTZ-B)
D = PTZ-D (RS-422 through Control Port PTZ-A or PTZ-B)
NOTE: A 96 x 16 system includes Control Ports PTZ-C and PTZ-D.
MON/ALM NUMBER: Enable (ON) or disable (OFF) on-screen display of the monitor/alarm number.
During normal operation, the monitor number appears in this field. The
monitor number is a fixed number, representing an actual BNC output on the
rear panel of the CM6800E. When an alarm is active, the logical alarm
number appears in this field.
C1528M-G (9/06)
53
MON/ALM STATUS:
Enable (ON) or disable (OFF) on-screen display of the monitor or alarm
status.
0001
0001
E
CAM 1
01-JAN-01 01:01:01
MONITOR STATUS DISPLAY VALUES:
Blank = normal status
H = hold
S = sequence
V
NOTE: If an operator presses the HOLD key while an alarm appears on the
monitor, the H does not appear. The alarm icon and alarm status value blink
to indicate the HOLD status.
ALM STATUS DISPLAY VALUES:
I = internal alarm
E = external alarm
V = video loss alarm
0001
0001
E
V
CAM 1
01-JAN-01 01:01:01
TIME:
Enable (ON) or disable (OFF) on-screen display of the time as programmed
in the system.
DATE:
Enable (ON) or disable (OFF) on-screen display of the date as programmed
in the system.
BRIGHTNESS:
Select the brightness level of the on-screen display (1-8; 8 = white characters, 1 = black characters; 2-7 = shades of gray).
0001
0001
E
CAM 1
01-JAN-01 01:01:01
If you select CURRENT in the MONITOR field, you can see the brightness level change as you scroll through the options.
If you select ALL in the MONITOR field, the changes do not take effect until you apply changes in the SET ALL field.
POSITION DISPLAY:
Navigate left or right to select the Test Positioning Menu.
The real-time camera display appears with Test Positioning Menu text
superimposed on the screen. Use the position keys or joystick to move the text to
the desired position on the screen. The text moves one line or character position at
a time.
---TEST POSITIONING MENU --PRESS PGM EXIT
Press the PGM key to exit the test positioning menu.
SET ALL:
To apply monitor display changes to all system monitors (if you selected ALL in the MONITOR field) you must navigate left
or right in the SET ALL field; otherwise monitor display settings are not changed.
If you selected CURRENT in the MONITOR field, navigating left or right in the SET ALL field has no effect.
54
C1528M-G (9/06)
PASSWORD
Use the Set Password screen to change the system password.
If you change the password and then forget the new one, you will have to reset the system to the factory defaults. All system programming will
be lost. Pelco recommends uploading your programming settings to the CM6800-MGR before changing the password. This allows you to
download the previous system settings, in the event of a system reset. If necessary, refer to the Troubleshooting section for the system reset
procedure.
SET PASSWORD
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
OLD PASSWORD: *******
NEW PASSWORD: *******
VER PASSWORD: *******
RETURN
Figure 45. Set Password Screen
Use the numerical keypad to enter the old and new passwords. The password must be seven digits.
1. Enter the current password (Default: 2899100).
2. Enter the new password.
3. Enter the new password again as a verification check.
Once the new password is accepted, the Main Menu appears.
C1528M-G (9/06)
55
PORTS (SERIAL/COM PORTS)
Use the Port screen to configure the settings for each device connected to a Serial/COM port on the rear panel of the CM6800E.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SET SERIAL PORT 05
DEVICE:
TYPE:
BAUD RATE:
PARITY:
DATA BITS:
STOP BITS:
REPORT ALARMS:
KBD300
RS485
9600
ODD
8
1
---
RETURN
Figure 46. Port Screen
1. Select the number of the desired Serial Port/COM port (01-10). The serial port numbers correspond to the communication ports on the
CM6800E rear panel as follows:
Serial Port
Input on CM6800E rear panel
01
COM 1 (accessed through either the DB9 input or RJ-45 port)
02-08
COM 2-8 RJ-45 inputs
09
PTZ-A control input
10
PTZ-B control input
2. Select the device connected to the COM port; the values in the TYPE, BAUD RATE, PARITY, DATA BITS, and STOP BITS fields change to the
settings appropriate for the specific device.
NOTE: “KBD300” is used to refer to the KBD100, KBD200A, and KBD300A keyboards.
3. Optional: Some device options allow a choice of communication type, baud rate, and/or parity rate. If this is the case, select the desired
settings.
4. Optional: If you select an ASCII device or if you use the CM6800E as a satellite device in a CM9760 system, you can select ON in the Report
Alarm field to set the CM6800E to report alarms to that device. The CM6800E reports the following alarm information:
Action
ASCII text
An alarm is triggered
#Ea
An alarm is cleared
#Ia
An alarm is acknowledged
#Ka
NOTE: The alarm number (#) reported by the CM6800 is based on the logical alarm number defined in the Logical Alarm Number screen.
Refer to Assign a Logical Alarm Number in the Alarm Programming section.
56
C1528M-G (9/06)
PRIORITY
The CM6800E provides eight levels of priority control. Each level defines the ability of a keyboard to control a pan/tilt/zoom (camera positioning
system) and to access programming screens.
Priority level applies system wide; a keyboard assigned priority level 2 on COM port 8 has a higher priority than a keyboard assigned priority level
4 on COM port 5. A higher level keyboard takes precedence over a lower level keyboard when the keyboards are issuing control commands.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
KEYBOARD PRIORITY MENU
PORT 05
KBD
1
2
3
4
5
6
7
8
PRIORITY
01
02
08
08
08
08
08
08
RETURN
Figure 47. Access the Priority Screen
PORT:
Select the COM port number for which you are programming priority control.
PRIORITY:
For each keyboard connected to the specified port, assign a priority level (01-08).
OPTIONS:
Level 1 = highest priority
Level 8 = lowest priority
Levels 1 - 3 have the ability to access programming screens. Levels 4-8 cannot access programming screens. The lowest level or
keyboards located at the same level will access devices on first-come, first-served basis.
NOTE: If you connect an ASCII keyboard/device to the CM6800E (COM port 1, 2, 4, 7, or 8), you can connect only one keyboard to a port. For
ASCII keyboards, priority control is based on the entry for keyboard 1.
C1528M-G (9/06)
57
96 X 16 SYSTEM SETTINGS
When you connect two CM6800E-48X8 units together in a 96 x 16 system, you must access the System programming screen and change the
setting to 96X16.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SYSTEM
96X16
RETURN
YOU SWITCHED TO: 96X16
IF YOU CONTINUE, SYSTEM WILL
ERASE USER PROGRAMMING AND
RESTORE SYSTEM SETTINGS TO
FACTORY DEFAULTS!!
CONTINUE? YES
RETURN
Figure 48. Change the System Setting
58
C1528M-G (9/06)
SEQUENCES
The CM6800E provides two types of sequences:
•
An operator can start a scratchpad sequence on one monitor, without accessing password-protected programming screens.
•
System sequences are password-protected and can run on any system monitor.
SEQUENCE 01
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
STP
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
CAM
0001
0002
0003
0004
0005
0006
0006
0006
0006
0006
0006
0006
0006
0006
0006
0006
0006
0006
DWL
02
02
03
02
08
02
02
02
02
02
02
02
02
02
02
02
02
02
HELP
CMD
PATT
PRES
SSCN
FSCN
PRES
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
NEXT
##
01
01
00
00
04
00
00
00
00
00
00
00
00
00
00
00
00
00
AUX
CON
CON
––––
––––
COFF
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
##
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
PREVIOUS
RETURN
Figure 49. Sequence Screen
SCRATCHPAD SEQUENCE MON ##
PELCO VIDEO SWITCHER
MODEL CM6800E
PASSWORD TO MAIN MENU
*******
SCRATCHPAD SEQUENCE
MACRO STATUS VIEW
RETURN
STP
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
CAM
0001
0005
0008
0012
0023
0006
0007
0008
0009
0010
0011
0012
0013
0014
0015
0016
0017
0018
DWL
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
CMD
PATT
PRES
FSCN
RSCN
SSCN
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
##
02
12
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
00
AUX
CON
GOFF
CON
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
––––
##
001
101
008
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
HELP
NEXT
PREVIOUS
RETURN
Figure 50. Scratchpad Sequence Screen
SEQUENCE:
Select the sequence number you want to program.
STP:
Each sequence can include up to 72 steps. For each step select entries for the following fields as necessary:
CAM:
Enter the desired camera number (logical number).
DWL:
Enter the dwell time (01-99 seconds).
CMD and ##:
Select a command; if you select a pattern or a preset enter a valid pattern or preset number.
OPTIONS:
PRES = preset
PATT = pattern
RSCN = random scan
FSCN = frame scan
SSCN = stop scan
AUX and ##:
Select an auxiliary to be activated.
Global = internal and external auxiliaries.
OPTIONS:
GON = turn global auxiliary on
GOFF = turn global auxiliary off
CON = turn camera auxiliary on
COFF = turn camera auxiliary off
NOTE: Activate the auxiliaries on the CM6800E rear panel by selecting global auxiliary numbers 1, 2, or
3 (in a 96 x 16 system the expansion unit auxiliaries are activated by global auxiliary numbers 4, 5, and 6).
The remaining global auxiliary numbers control REL2064 Relay Interface Unit auxiliaries.
C1528M-G (9/06)
59
TIME AND DATE
Use the Time and Date screen to set the system time and date settings. The time and date displayed on the monitor during real-time camera
display is the time set in the memory through this screen. The system time and date information is kept current in battery-backed RAM. New
time and date information will be set when you apply the changes (refer to the SET TIME & DATE field description).
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SET TIME & DATE
SET
DATE:
TIME:
MM DD YY
01 / 01 / 01
01 : 01 : 01
DISPLAY AS
FORMAT: DD/MMM/YY
STYLE:
24Hr
SET TIME & DATE
RETURN
Figure 51. Access the Time and Date Screen
1. Select or enter the month, day, and year of the desired system date.
2. Select or enter the hour, minute, and second of the desired system time.
3. Select the on-screen date format.
OPTIONS:
DD/MMM/YY
MMM/DD/YY
YY/MMM/DD
DD/MM/YY
MM/DD/YY
YY/MM/DD
4. Select the on-screen time format. This setting affects the on-screen time displayed on system monitors only. System functions programmed
through the event timers (refer to Event Timers in this section) are based on 24-hour time settings.
OPTIONS:
24Hr
AM/PM (12 Hr)
5. Navigate left or right in the SET TIME & DATE field to apply the changes.
PATTERNS, PRESETS, AND ZONES
Special characters added through the CM6800-MGR may not be available with your camera positioning system. Preset, pattern, and zone labels
containing special characters will appear on the monitor with blanks in place of the special characters.
Refer to the Operations section for instructions on creating patterns. Refer to your keyboard manual for instructions on programming presets and
zones.
OPERATION
60
C1528M-G (9/06)
Operations
OVERVIEW
A brief description of CM6800E operation is provided here. Refer to the following sections for detailed instructions and options.
Install the CM6800E and connect all system devices.
Refer to the Installation section.
Power-up the system.
Refer to the System Start-up section.
Switch monitor.
1. Enter the monitor number.
2. Press the MON key.
Select camera.
1. Enter the camera number.
2. Press the CAM key.
Control PTZ receivers.
Use the appropriate PTZ control keys or joystick (depending on the keyboard used).
Extended Coaxitron protocol receivers can be operated without any programming
changes. Other receiver control protocols require programming changes.
Call a preset.
Program the preset through the keyboard.
1. Enter the preset number.
2. Press the PRESET key or Prst/Lock key (depending on the keyboard used).
System does not function.
Refer to the Troubleshooting section.
OPERATING THE CM6800E
The CM6800E can be operated with a KBD100, KBD200A, KBD300A, KBD960, or KBR960 keyboard. Operation instructions are provided below,
but you should become familiar with the detailed instructions provided in the appropriate keyboard manual.
The CM6800E can also be controlled with ASCII commands. Refer to the ASCII Operating Commands section in the Appendix.
SWITCH MONITORS
If you select a restricted monitor, the monitor does not switch; the keyboard LED displays the previously selected monitor number.
ALL KEYBOARDS
1. Enter the monitor number.
2. Press the MON key. The keyboard LED displays the selected monitor number.
SELECT CAMERAS
If you select a restricted camera view, the camera view does not appear on that monitor. The previously selected, unrestricted camera view
remains on the monitor.
KBD100/200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
1. Enter the camera number.
1. Enter the camera number.
2. Press the CAM key.
2. Press the CAM key.
OR
OR
Press the BWD or FWD key to scroll through the available cameras.
Press the PREV or NEXT key to scroll through the available cameras.
OR
From the Camera Menu, select
available cameras.
C1528M-G (9/06)
or
to scroll through the
61
CONTROL RECEIVERS
Select a suitable camera and operate a PTZ function. A keyboard with “view-only” access can view the signal from the specified camera but
cannot control the camera.
Extended Coaxitron protocol receivers can be operated without any programming changes. Other receiver control protocols require programming
changes. Refer to the Programming the CM6800E section.
Receiver control is not available with the KBD100 keyboard.
KBD200A KEYBOARD
Pan/Tilt/Zoom
Lens Control: Focus, Iris
Press and hold the appropriate pan/tilt key until the camera reaches
the desired position. To change the speed of movement, press a
number (1-9) key first (1=slowest, 9=fastest). Press and hold the
appropriate zoom key until the desired effect is seen.
Press and hold the appropriate lens control key until the desired
effect is seen.
KBD300A KEYBOARD
Pan/Tilt/Zoom
Lens Control: Focus, Iris
Move the joystick until the camera reaches the desired position. To
increase the speed of movement, move the joystick farther from
center.
Press and hold the appropriate lens control key until the desired
effect is seen.
Twist the joystick clockwise to zoom in, counterclockwise to zoom
out.
KBD960/KBR960 KEYBOARDS
Pan/Tilt/Zoom
Lens Control: Focus, Iris
Move the joystick until the camera reaches the desired position. To
increase the speed of movement, move the joystick farther from
center or press the T key to pan at turbo speed.
Use the NEAR/FAR key to focus near or far.
Use the OPEN/CLS key to open or close the iris.
Twist the joystick clockwise to zoom in, counterclockwise to zoom
out. Or use the IN/OUT key to zoom in or out.
62
C1528M-G (9/06)
OPERATE SEQUENCES
You can run a scratchpad sequence from an individual monitor or a system sequence on any monitor accessible from the keyboard. When running
a sequence, any cameras not accessible to the keyboard will be bypassed.
A sequence runs continuously until a system operator selects a different camera, or an event timer starts another sequence or macro.
KBD100/200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
Run a Sequence
Run a Sequence
1. Enter a sequence number (1-32). Skip this step to run a scratchpad
sequence.
1. Select
2. Press and hold the NEXT or PREV key to move forward or
backward through the sequence.
To move through the sequence one camera at a time:
Press the NEXT key to move forward.
Press the PREV key to move backward.
Pause a Sequence
1. Press the HOLD key; monitor displays H.
.
2. Enter a sequence number (1-32 for a system sequence; 0 for the
scratchpad sequence).
3. Select
to start the sequence.
SEQ
OR
1. Select
2. Select
.
to enter the Sequence Menu.
SEQ
3. Enter a sequence number (1-32).
2. Press the HOLD key to resume.
OR
Stop a Sequence
Select
or
to scroll through available sequences.
4. Select
or
to start the sequence.
1. Enter a camera number.
2. Press the CAM key.
NOTE: You can define a function key to run a sequence. Refer to the
KBD960 Keyboard Installation/Operation Manual for instructions.
Pause a Sequence
1. Select
2. Select
or
to resume.
Stop a Sequence
1. Select
.
OR
1. Enter a camera number.
2. Press the CAM key.
C1528M-G (9/06)
63
RUN A MACRO
A macro runs until the last step is completed (unless you specify a loop in the macro).
KBD100/200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
Run a Macro
Run a Macro
1. Enter the macro number.
1. Select
2. Press the MACRO key.
2. Enter a macro number.
Stop a Macro
3. Select
1. Enter the number of the running macro.
OR
2. Press the MACRO key.
1. Select
NOTE: Any macro or sequence started by this macro will continue
to run.
2. Select
.
to start the macro.
MAC
.
to enter the Macro Menu.
MAC
3. Enter a macro number.
OR
Select
or
to scroll through available macros.
4. Select
or
to start the macro.
NOTE: You can define a function key to run a macro. Refer to the
KBD960 Keyboard Installation/Operation Manual for instructions.
Pause a Macro
1. Select
.
2. Select
or
to resume.
Stop a Macro
1. Select
.
OR
1. Enter a camera number.
2. Press the CAM key.
ACKNOWLEDGE AN ALARM
When an alarm is triggered, an alarm icon appears on the monitors programmed to show that alarm.
KBD100/200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
1. Enter the monitor number.
1. Select
.
2. Press the MON key.
2. Select
to reset the alarm on the individual monitor.
3. Press the ACK key. The alarm is removed from the selected
monitor.
4. Repeat for each alarm.
OR
Select
to reset the alarm on all monitors.
You can also select
to mute the alarm.
NOTE: You can define a function key to acknowledge an alarm.
Refer to the KBD960 Keyboard Installation/Operation Manual for
instructions.
64
C1528M-G (9/06)
CALL A PRESET
Program the preset through the keyboard. Refer to the appropriate keyboard manual for instructions. Presets are not available with the KBD100
keyboard.
KBD200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
1. Enter the preset number.
1. Enter the preset number.
2. Press the PRESET key.
2. Press the Prst/Lock key.
OR
Select the PRST icon.
CREATE AND RUN A PATTERN
Patterns are not available with the KBD100 keyboard.
KBD200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
Create a Long Pattern
Refer to the KBD960 Keyboard Installation/Operation manual for
instructions on creating a pattern.
1. Enter a camera number.
2. Enter 0.
3. Press and hold the PATTERN key for two seconds.
1. Select
PRST
2. Select
to display the Preset Menu.
to start a pattern.
OR
4. The monitor will indicate the programming function is active.
Move the camera position as desired for the pattern.
1. Select
5. Press the ACK key to close the programming function.
2. Enter 1.
Create a Short Pattern
3. Select
to run the first pattern of previously defined
half-patterns.
1. Enter a camera number.
2. Enter the short pattern number (1 or 2).
3. Press and hold the PATTERN key for two seconds.
4. The monitor will indicate the programming function is active.
Move the camera position as desired for the pattern.
5. Press the ACK key to close the programming function.
PRST
to display the Preset Menu.
OR
1. Select
PRST
to display the Preset Menu.
2. Enter 2.
3. Select
to run the second pattern of previously defined
half-patterns.
Run a Long Pattern
1. Press the PATTERN key.
2. Move the joystick or call a preset to stop the pattern.
Run a Short Pattern
1. Enter the short pattern number (1 or 2).
2. Press the PATTERN key.
3. Move the joystick or call a preset to stop the pattern.
C1528M-G (9/06)
65
OPERATE AUXILIARIES/RELAYS
Local auxiliaries are the outputs on the rear panel of the CM6800E. External auxiliaries are available by connecting an REL2064 Relay Interface
Unit to the CM6800E through COM port 3.
Operate a Local Auxiliary
KBD100/200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
Auxiliary 1 relay: Press F1 to activate/deactivate.
Auxiliary 1 relay: Press F12* to activate/deactivate.
Auxiliary 2 TTL output: Press F2 to activate/deactivate.
Auxiliary 2 TTL output: Press F24* to activate/deactivate.
* F12 and F24 are the default auxiliary control function keys;
user-selected function keys can be defined through the Key Define
Menu. Refer to the KBD960 Keyboard Installation/Operation
Manual for instructions.
NOTE: If you connect REL2064 Relay Interface Units (up to four) to
the CM6800E, operation of the two relays on the rear panel of the
CM6800E will also operate the first two relays on the first external
unit (unless you number the external relays starting at 64).
Operate an External Auxiliary
The CM6800E can control up to four REL2064 Relay Interface Units connected to the system. Each unit provides 64 relays. Refer to the REL2064
Relay Interface Unit Installation/Operation Manual for detailed information. External relays cannot be operated with the KBD100.
KBD200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
The KBD200A/300A keyboards (firmware version 4.2 and later) can
operate external relays.
1. Enter the GPI number for the appropriate relay output.
Refer to the KBD200A Keyboard Installation/Operation Manual or the
KBD300A Keyboard Installation/Operation Manual for instructions.
NOTE: External relays cannot be operated with KBD200A/300A
keyboard firmware versions prior to 4.2.
2. Press
GPI
.
3. Press the desired AUX number icon to activate the relay and
associated peripheral device.
(Press
to access AUX 5-8.)
4. If MTRY is highlighted, the operation is momentary. If MTRY is not
highlighted, the operation is latching. Refer to the KBD960
Keyboard Installation/Operation Manual for instructions.
Operate an Auxiliary in a Receiver
Auxiliary control is not available with the KBD100.
KBD200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
Press AUX ON/F4 to activate.
1From the Camera Menu, press 1 , and then release to control an
AUX 1 momentary function on the selected camera.
Press AUX OFF/F5 to deactivate.
OR
Press
access
2
3
to control an AUX 2 momentary function. Press
through 8 .
to
To control a momentary function:
1. Enter the auxiliary number.
2. Press and hold AUX ON/F4, and then release.
66
C1528M-G (9/06)
CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER DISPLAYS
Multiplexer control is not available with the KBD100.
KBD200A/300A KEYBOARDS
KBD960/KBR960 KEYBOARDS
1. Enter the number of the multiplexer input.
2. Press the CAM key.
1. Enter a MUX input number and press
. Each MUX input is
associated with a camera input. Figure 43 shows MUX 1 being
controlled.
3. Press the SHIFT key. When the SHIFT LED is lit, the keyboard can
be used to operate the following Genex multiplexer function keys:
2. Select MUX . MUX Menu 1 appears. MUX should be highlighted,
which means you have MUX control.
F1: Digital zoom
F2: PIP display
F3: Quad display
AUX ON/F4: 9-screen display
AUX OFF/F5: 16-screen display
To select a camera through the multiplexer:
a. Enter the desired camera number (1-16, based on the camera
assignments set through the multiplexer).
b. Press the CAM key.
4. Press the SHIFT key to return to normal keyboard operation.
When the SHIFT LED is off, you can control the currently selected
PTZ camera through the multiplexer.
To return to camera selection controlled by the CM6800E:
a. Select the desired camera number.
3. Cycle through the 16 picture inserts (if you have a 16-channel
multiplexer) by entering the camera number and selecting
.
4. Select
again to zoom into the MUX camera. You can move
the joystick to view a specific area.
5. Select
to bring up MUX Menu 2. The icons for a
picture-in-picture display, 4-camera display, 9-camera display, and
16-camera display appear.
6. Select
to view four of the available 16 cameras on one
monitor. You can cycle through all 16 cameras, four at a time, by
repeatedly selecting
.
7. Select
to view nine of the available 16 cameras on one
monitor. Select again to see the remaining seven cameras.
8. Select
Note that
to view all 16 available cameras on one monitor.
does not work on a 9-channel mulitplexer.
b. Press the CAM key.
c. Move the joystick as necessary.
OPERATE SCANNING FUNCTIONS
Operation of the scanning functions depends on the kind of receiver or pan/tilt mechanism you have. Refer to the appropriate keyboard manual
for detailed instructions on operating scanning functions.
DETECT VIDEO LOSS
The CM6800E detects video loss from any system camera. If video is lost from a camera, the CM6800E blue screen appears on any monitor
viewing that camera. When video is restored to that camera, the camera view appears on the monitor(s) again. If the system is programmed for
a video loss alarm, the alarm icon appears.
DEFINE ZONES
A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is associated. When the associated camera is panned
through or remains within this defined zone the zone label appears on the monitor.
Refer to the appropriate keyboard manual for detailed instructions on defining zones.
C1528M-G (9/06)
67
Appendix
CM6800E DIP SWITCHES
Figure 52. CM6800E DIP Switches – Factory Default Settings
Table G. CM6800E DIP Switch Settings
CM6800E DIP Switch
68
Default Setting
Switch 1
OFF (0) = NTSC
ON (1) = PAL
CM6800E-48X8: OFF
CM6800E-48X8-X: ON
Switch 2
RESERVED – must be in the OFF position for proper operation
OFF
Switch 3
RESERVED – must be in the OFF position for proper operation
OFF
Switch 4
RESERVED – must be in the ON position for proper operation
ON
Switch 5
RESERVED – must be in the OFF position for proper operation
OFF
Switch 6
RESERVED – must be in the OFF position for proper operation
OFF
Switch 7
USED TO RESET SOFTWARE. Refer to Software Reset in the Troubleshooting
section.
CAUTION: Resetting the software restores the system software to
original settings, programmed by Pelco. All user programming is lost.
OFF
Switch 8
RESERVED – must be in the OFF position for proper operation
OFF
C1528M-G (9/06)
ALARM GROUP DISPLAY OPTIONS
To display on a monitor, an alarm must be assigned to an alarm group (A-H). Before programming alarms you may want to determine the alarm
display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display as a part of each alarm.
A priority alarm appears on system monitors before non-priority alarms, despite the order specified by the alarm group assignment. In the
examples below, all alarms are at the same priority level. Refer to the PRIORITY description in Program an Internal or External Alarm Contact.
BLOCK BUILD
Alarmed cameras are displayed across a block of alarm monitors in a sequential order. All steps programmed for the alarm contact appear on the
designated monitor.
Example: Eight alarms set to display on monitors 02-07 will appear in the following order:
Monitor
1st Display
Cycle
Next Display
Cycle
Acknowledging
Alarms 1 & 2
Next Display
Cycle
02 B
1st alarm
1st and 7th
alarms cycle
Acknowledge
1st alarm
7th alarm
ALARM MONITOR GROUP SETUP
03 B
2nd alarm
2nd and 8th
alarms cycle
Acknowledge
2nd alarm
8th alarm
04 B
3rd alarm
3rd alarm
3rd alarm
3rd alarm
05 B
4th alarm
4th alarm
4th alarm
4th alarm
06 B
5th alarm
5th alarm
5th alarm
5th alarm
07 B
6th alarm
6th alarm
6th alarm
6th alarm
MON
A
B
C
D
E
F
G
H
01
02
03
04
05
06
07
08
–
B
B
B
B
B
B
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
HELP
00638
New alarms display on the lowest monitor number with the fewest alarms cycling.
CHRONOLOGICAL PAIR: D AND Q
The oldest alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on the second
designated monitor. All steps programmed for the alarm contact appear on the designated monitor.
Example: Four alarms set to display on monitors 04 and 05 will appear in the following order:
Monitor
1 Alarm
2 Alarms
3 Alarms
4 Alarms
04 D
1st alarm
1st alarm
1st alarm
1st alarm
05 Q
2nd alarm
2nd and 3rd
alarms cycle
2nd, 3rd, and 4th
alarms cycle
You must acknowledge alarms in a chronological pair from the display monitor (D). Then the
next oldest alarm moves to the display monitor and the remaining alarms continue to cycle
through the queue monitor (Q). This format requires you to acknowledge each alarm in the
order in which they occur.
Acknowledging alarms in this example:
A
B
C
D
E
F
G
H
01
02
03
04
05
06
07
08
–
–
–
–
–
–
–
–
–
–
–
D
Q
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
HELP
00640
Monitor
1st Cycle
Next Cycle
Next Cycle
Next Cycle
04 D
Acknowledge
1st alarm
Acknowledge
2nd alarm
Acknowledge
3rd alarm
Acknowledge
4th alarm
05 Q
2nd, 3rd, and 4th
alarms cycle
3rd and 4th
alarms cycle
4th alarm
C1528M-G (9/06)
ALARM MONITOR GROUP SETUP
MON
69
REVERSE CHRONOLOGICAL PAIR: M AND L
The most recent alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on the
second designated monitor. All steps programmed for the alarm contact appear on the designated monitor.
Example: Four alarms set to display on monitors 06 and 07 will appear in the following order:
Monitor
06 M
1 Alarm
2 Alarms
1st alarm
3 Alarms
2nd alarm
07 L
3rd alarm
1st alarm
1st and 2nd
alarms cycle
4 Alarms
1st alarm
1st, 2nd, and 3rd
alarms cycle
You must acknowledge alarms in a reverse chronological pair from the display monitor (M).
Then the next most recent alarm moves to the display monitor and the remaining alarms
continue to cycle through the queue monitor (L). This format requires you to acknowledge each
alarm in the reverse order from which they occurred.
ALARM MONITOR GROUP SETUP
MON
A
B
C
D
E
F
G
H
01
02
03
04
05
06
07
08
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
M
L
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
HELP
00641
Acknowledging alarms in this example:
Monitor
1st Cycle
Next Cycle
Next Cycle
Next Cycle
06 M
Acknowledge
Alarm 4
Acknowledge
Alarm 3
Acknowledge
Alarm 2
Acknowledge
Alarm 1
07 L
Alarms 1, 2,
and 3 cycle
Alarms 1 and 2
cycle
Alarms 1
SALVO GROUP
Multiple camera views within the alarm contact programming (the “steps”) are displayed simultaneously as a group across a set of monitors.
When a new alarm triggers, all monitors switch to the new alarm at the same time.
When programming a Salvo Group:
•
Program the Salvo Group to display across a number of monitors equal to the number of steps in the alarm contact(s); for example if the
alarm contact has six steps, set the Salvo Group to display on six monitors. If an alarm contact contains more steps than monitors defined
for the Salvo Group, the additional steps do not appear on a monitor during the alarm.
•
Each alarm contact assigned to the Salvo Group should contain the same number of steps.
•
The Salvo Group switches based on the dwell time entered for the first step in the alarm contact.
Example: Two alarm contacts with three steps display on three monitors will appear as follows:
After
Acknowledging
1st Alarm
Monitor
1 Alarm
2 Alarms
Next Display
Cycle
06 S
1st alarm, step 1
2nd alarm, step 1
1st alarm, step 1
2nd alarm, step 1
07 S
1st alarm, step 2
2nd alarm, step 2
1st alarm, step 2
2nd alarm, step 2
08 S
1st alarm, step 3
2nd alarm, step 3
1st alarm, step 3
2nd alarm, step 3
ALARM MONITOR GROUP SETUP
MON
A
B
C
D
E
F
G
H
01
02
03
04
05
06
07
08
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
S
S
S
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
HELP
00639
70
C1528M-G (9/06)
MACRO COMMANDS
Table H provides a description of each macro command and the additional fields required for each command. Refer to the Macros section for
instructions on programming macros.
Table H. Macro Commands
Command
Description
Specify
GON
Activate an auxiliary.
Auxiliary
GOFF
Turn off an auxiliary.
Auxiliary
Auxiliary Notes:
• “Global” includes both internal and external auxiliaries.
• Auxiliaries on the rear panel of the CM6800E Matrix Switcher are activated by global auxiliary numbers 1, 2 and 3.
CON
Activate a camera auxiliary.
Camera auxiliary
Camera
Monitor
COFF
Turn off a camera auxiliary.
Camera auxiliary
Camera
Monitor
SEQ
Start a sequence. A sequence runs continuously until a system operator selects a
Sequence
different camera, or an event timer starts another sequence or macro.
Monitor
SWT
Switch a camera to a monitor.
COPY
Copy a camera view to a monitor.
Go To
Go to step number specified.
Loop
Loop a macro.
?AUX
Check a local auxiliary; if the auxiliary is active, the next step is executed; if the
auxiliary is not active, the next step is skipped.
Check an internal alarm; if the alarm is active, the next step is executed; if not, the
next step is skipped.
Check whether a camera is displayed on a monitor; if it is, the next step is
executed; if not, the next step is skipped.
?ALM
?SW
STPM
End
DON
DOFF
MSWT
Stop a macro.
Exit the macro; no further steps are executed. Any macro or sequence started by
this macro will continue to run.
Displays on-screen text on the specified monitor.
Removes on-screen text from the specified monitor.
Switch a camera connected through the multiplexer.
PIPB
Display multiplexer picture-in-picture view with the designated camera in the
background.
PIPF
Display multiplexer picture-in-picture view with the designated camera in the
foreground.
Camera
Monitor
Monitor to copy from
Monitor to copy to
Step
Field(s)
Command #
Command #
Command #
Camera
Monitor
Command #
Camera
Monitor
Command #
Monitor
Command #
Monitor
Command #
Monitor
Command #
0 = loop continuously
1-999 = loop the specified
number of times
Local auxiliary
Command #
Alarm
Command #
Camera
Monitor
Macro
None
Camera
Monitor
Command #
None
Monitor
Monitor
Camera to switchu
Monitor
Monitor
Multiplexer input
Monitor
Background camerau
Multiplexer input
Monitor
Foreground camerau
Multiplexer input
Monitor
Command #
Command #
Camera
Monitor
Command #
Camera
Monitor
Command #
Camera
Monitor
u
For multiplexer functions, the camera number is the number of the video input on the multiplexer. The multiplexer input number is the number of the
video input on the rear panel of the CM6800E.
(Continued on next page)
C1528M-G (9/06)
71
Table H. Macro Commands (Continued)
Command
PIPO
Description
Turn off multiplexer picture-in-picture view.
QUAD
Display multiplexer four-camera mode.
NANO
Display multiplexer nine-camera mode.
HEX
Display multiplexer sixteen-camera mode.
Zoom
Zoom multiplexer camera view.
AAI
DAI
AAE
DAE
AAV
Arm internal alarm.
Disarm internal alarm.
Arm external alarm.
Disarm external alarm.
Arm video loss detection for a camera.
DAV
Disarm video loss detection for a camera.
MACR
PATT
Start a specific macro. A macro runs until the last step is completed (unless you
specify a loop in the macro).
Start a pattern.
PRES
Start a preset.
RSCN
Start a random scan.
FSCN
Start a frame scan.
SSCN
Stop a scan.
Specify
Multiplexer input
Monitor
Camera group*
Multiplexer input
Monitor
Camera group*
Multiplexer input
Monitor
Multiplexer input
Monitor
1 = zoom once
2 = zoom twice
Multiplexer input
Monitor
Internal alarm
Internal alarm
External alarm
External alarm
Physical camera number
OR
Logical camera number
Physical camera number
OR
Logical camera number
Macro
Pattern**
Camera
Monitor
Preset**
Camera
Monitor
Camera
Monitor
Camera
Monitor
Camera
Monitor
Field(s)
Camera
Monitor
Command #
Camera
Monitor
Command #
Camera
Monitor
Camera
Monitor
Command #
Camera
Monitor
Command #
Command #
Command #
Command #
Command #
Camera
Command #
Camera
Command #
Command #
Camera
Monitor
Command #
Camera
Monitor
Camera
Monitor
Camera
Monitor
Camera
Monitor
*Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual for information on multiple camera displays.
**The number of patterns and presets available is determined by the camera positioning system. Refer to the appropriate camera positioning system
manual.
72
C1528M-G (9/06)
USING THE CM6800E-48X8 AS A SATELLITE DEVICE IN A 9700 SYSTEM
The CM6800E-48X8 can function as a remote satellite switcher in a 9700 System (a “9700 System” is any matrix system using a CM9700-CC1;
the CM9740/9760 systems are also supported). You can view and control up to 96 video inputs on the CM6800 either locally (from the CM6800),
or remotely (from 9700 System keyboard operators).
The following connection instructions refer to the CM9700-CC1; the same instructions also apply to the CM9760-CC1 and the CM9740-CC1.
Instructions are also provided for programming the CM6800E-48X8 as a satellite device within the 9700 System configuration files. Note that the
programming steps differ, depending on whether you are using the CM9760-MGR System Manager software or the CM9700-MGR System
Manager software. Instructions for both applications are provided.
INSTALL THE CM6800E AS A SATELLITE DEVICE
1. Install the CM6800E-48X8, in either a 48 x 8 or 96 x 16 configuration, and then connect the cameras. Refer to the instructions in the
Installation section.
You can also connect the following optional components:
•
PTZ receivers
•
internal alarms
•
external alarms; up to four ALM2064 units can be connected, using COM 3
•
local monitor and keyboard for programming the CM6800E-48X8 (or you can program the CM6800E from a keyboard connected to the
CM9760 system)
2. Use a straight data cable to connect port 7 on the CM6800E-48X8 to the next available sercom port on the CM9760-CC1. Refer to the port
assignment table in the CM9740/CM9760 System documentation.
If the CM6800E-48X8 is more than 6 feet away from the CM9760-CC1, use two wall blocks and additional cables as needed. Connect the
wall block pins 1, 2, 5, 7, and 8 at each end.
3. Connect video cable tie lines from the CM6800E-48X8 monitor output ports to the video input BNC receptacles on the CM9760-MXB.
The number of CM6800E cameras that the 9700 System can control at any one time, depends on the number of tie lines connected
between the two systems. If you connect two tie lines, the 9700 System can control a maximum of two CM6800E cameras at one time. You
can connect a maximum of eight tie lines.
Note that you must use the CM6800E-48X8 monitor outputs in sequential order, starting with monitor output 1. If you use a local monitor to
program the CM6800E-48X8, the local monitor must have the highest assigned number.
C1528M-G (9/06)
73
Figure 53. Data and Tie Line Connections Between CM6800E-48X8 and CM9700/CM9740/CM9760
4. After completing system installation and power-up, select the appropriate CM6800E satellite settings in programming mode. In addition,
you must configure satellite settings in the CM9700/CM9740/CM9760 system. Refer to the following section.
74
C1528M-G (9/06)
CONFIGURE THE CM6800E AS A SATELLITE DEVICE
In addition to any programming needed for the devices connected to the CM6800E-48X8 (such as camera control and monitor settings), you must
configure the following CM6800E satellite settings.
•
Monitor Access: Change the appropriate monitor access to TIE LINE
•
Port: Change the Port 7 device setting to SATELLITE
•
Alarms (optional): Enable the appropriate internal and external alarm contacts, and then set them to report to the CM740/CM9760 system.
Satellite programming instructions are provided in the following sections. Refer to the Programming the CM6800E section for basic instructions
on programming the CM6800E matrix switcher.
Once the CM6800E programming is complete, then you must configure the CM6800E-48X8 as a satellite device within the 9700 System
configuration files. If you are using the CM9700-MGR System Manager software, refer to the Configure CM9700-MGR System Manager Settings
section. If you are using the CM9760-MGR System Manager software, refer to the Configure CM9760-MGR System Manager Settings section.
Satellite Monitor Access
Change the setting to TIE LINE for each monitor output connected to the 9700 System matrix bay, as shown below. Note that you must use the
CM6800E-48X8 monitor outputs in sequential order, starting with monitor output 1.
NOTE: You cannot change the access setting of the monitor you are currently viewing.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SATELLITE VIEW
ACCESS
1
2
3
4
MON
1
2
3
4
5
6
7
8
KEYBOARD TO MONITOR
CAMERA TO KEYBOARD
CAMERA TO MONITOR
SATELITE VIEW
PTZ TIME OUT: ON
RETURN
VIEW
TIE LINES
TIE LINES
TIE LINES
TIE LINES
TIE LINES
TIE LINES
TIE LINES
LOCAL
RETURN
Figure 54. Set Satellite Access
Satellite Port Settings
Change the device setting to SATELLITE for Port 7. The REPORT ALARMS setting changes to ON by default. If you do not want to report alarms to
the CM9740/CM9760 system, change this field to OFF (refer to the Satellite Alarms section for information on reporting alarms).
NOTE: You must also configure the appropriate CM9760-CC1 port with a baud rate of 9600 and odd parity.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
SET SERIAL PORT 07
DEVICE:
TYPE:
BAUD RATE:
PARITY:
DATA BITS:
STOP BITS:
REPORT ALARMS:
SATELLITE
RS485
9600
ODD
8
1
ON
RETURN
Figure 55. Change the Port Setting
C1528M-G (9/06)
75
Satellite Alarms
This procedure is optional.
1. Enable the appropriate internal and external alarm contacts. Refer to the Program an Internal or External Alarm Contact section for detailed
instructions.
INTERNAL ALARM MENU
CONTACT:
ACK TYPE:
TYPE:
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
ENABLE:
OFF
TIME OUT: 10
PRIORITY: 0
STP
CAM
DWL
CMD
##
AUX
##
1
2
3
4
5
6
7
8
0001
0001
0001
0001
0001
0001
0001
0001
01
00
00
00
00
00
00
00
PRES
––––
––––
––––
––––
––––
––––
––––
13
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
000
000
000
000
000
000
000
000
ALARM CONTACTS
1
2
3
4
5
1
MANUAL
NO
A
B
Y
N
GROUP ENABLE
C D E F G
N
N
N
N
N
H
N
RETURN
INTERNAL CONTACT
EXTERNAL CONTACT
VIDEO LOSS
ALARM GROUP
LOGICAL ALARM NUMBER
EXTERNAL ALARM MENU
RETURN
CONTACT:
ACK TYPE:
PRIORITY:
001
MANUAL
0
ENABLE:
OFF
TIME OUT: 10
STP
CAM
DWL
CMD
##
AUX
##
1
2
3
4
5
6
7
8
0001
0001
0001
0001
0001
0001
0001
0001
00
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
00
00
00
00
00
00
00
00
––––
––––
––––
––––
––––
––––
––––
––––
000
000
000
000
000
000
000
000
A
B
N
N
GROUP ENABLE
C D E F G
N
N
N
N
N
H
N
RETURN
Figure 56. Enable Alarm Contacts
2. In the appropriate Logical Alarm Number screen, assign a logical number for each alarm contact, in sequential order. The logical numbers
assigned in this screen are reported to the CM9740/CM9760 system and they must match the physical numbers configured in the CM9740/
CM9760 system (refer to Program the Alarms File in the Configure CM9760-MGR System Manager Settings section). These numbers are
used by the CM9760-KBD keyboard to arm or acknowledge an alarm.
LOGICAL ALARM NUMBER CONSIDERATIONS:
•
If you set the CM6800E to report any CM6800E alarms to the CM9740/CM9760 system, you must assign each CM6800E alarm a logical
alarm number that is unique within the CM9740/CM9760 system (i.e. when used as a satellite device, the CM6800E shares the same pool
of logical alarms numbers as the CM9740/CM9760 system).
•
To configure a CM6800E alarm(s) to report only within the CM6800E system, and not to the CM9740/CM9760 system, assign the alarm(s) a
logical alarm number of 0. When the alarm(s) is triggered, the physical number of the alarm(s) appears on the CM6800E system monitor(s).
LOGICAL ALARM NUMBER MENU
1 LOGICAL INTERNAL ALARM
2 LOGICAL EXTERNAL ALARM
3 LOGICAL VIDEO LOSS
RETURN
LOGICAL INTERNAL ALARM
LOG
0001
0002
0003
0004
0005
0006
0007
0008
PHY
1
2
3
4
5
6
7
8
RETURN
Figure 57. Assign Satellite Logical Alarm Numbers
3. Configure a CM9760-MGR Alarms file for each satellite alarm. Refer to Configure CM9760-MGR System Manager Settings in this section.
76
C1528M-G (9/06)
CONFIGURE CM9700-MGR SYSTEM MANAGER SETTINGS
Instructions for configuring the CM6800-E-48X8 as a satellite device with the CM9700-MGR System Manager software are provided here. If you
are using the CM9760-MGR System Manager software, refer to the Configure CM9760-MGR System Manager Settings section.
To add a satellite device to a 9700 system, simply add the satellite device in the CM9700-MGR. Detailed instructions for adding a satellite device
in the CM9700-MGR are provided in the CM9700-MGR Software Guide.
Note that you cannot program camera titles for satellite cameras through the 9700 System Manager. Program these camera titles directly from
the satellite device. When a 9700 System monitor displays a satellite camera, the title received from the satellite device is displayed.
Figure 58. Add a Satellite Device in the CM9700-MGR
Once the CM9700-MGR system configuration file programming is complete, you must transfer the configuration files (the “flat files”) to the
CM9700-CC1. Refer to the CM9700-MGR Software Guide for instructions.
CONFIGURE CM9760-MGR SYSTEM MANAGER SETTINGS
Instructions for configuring the CM6800-E-48X8 as a satellite device with the CM9760-MGR System Manager software are provided here. If you
are using the CM9700-MGR System Manager software, refer to the Configure CM9700-MGR System Manager Settings section.
To control the CM6800E-48X8 as a satellite device from the CM9740/CM9760 system, program the following CM9740/CM9760 system
configuration files:
•
COMMS file
•
CAMERAS file
•
LINK CAMERAS file
•
ALARMS file (optional; only required if the CM6800E-48X8 reports alarms to the CM9740/CM9760 system)
Once the CM9740/CM9760 system configuration file programming is complete, you must transfer the configuration files (the “flat files”) to the
CM9760-CC1. Refer to the CM9740/CM9760 System documentation for instructions.
CAUTION: Before programming any CM9740/CM9760 configuration file, or cycling power to the CM6800E, ensure that only CM9740/
CM9760 cameras are displayed on CM9740/CM9760 system monitors. The CM9740/CM9760 system should not have any CM6800E
satellite cameras displayed on CM9740/CM9760 system monitors.
Use the CM9760-MGR System Manager software to program these files. The illustrations provided on the following pages document the
8.03.006 version of the software. Instructions are also provided for the lower software versions (7.08.029 and below).
NOTE: Refer to the CM9740/CM9760 System documentation for additional instructions on programming the CM9740/CM9760 system.
Complete the following steps to open the CM9760-MGR Setup System Configuration window:
1. Start the CM9760-MGR and log in.
2. Click the 9760-Setup icon. The Configuration Files dialog box appears.
3. Click Setup Files. The Setup System Configuration window appears.
C1528M-G (9/06)
77
Program the Comms File
1. Click the Comms tab. The Comms page appears.
COMMS TAB
SERCOMM PORT
EQUIPMENT NUMBER
DESCRIPTION
BAUD RATE PARITY
Figure 59. CM9760-MGR Comms Page
2. In the list of Defined Ports, select the Sercom controller port used for connecting the CM6800E-48X8.
3. Click the arrow on the equipment number field, and then select the CM6800E equipment number.
•
If the CM9760-MGR software is version 7.08.029 or lower, select equipment number 31.
•
If the CM9760-MGR software is version 8.03.006 or higher, select equipment number 35.
4. Click the arrow on the baud rate drop-down box, and then select 9600.
5. Click the arrow on the parity drop-down box, and then select Odd.
6. Save the changes. You will need to transfer the changes to the CM9760-CC1 by floppy disk. Refer to the CM9740/CM9760 System
documentation for instructions.
78
C1528M-G (9/06)
Program the Cameras File
1. Click the Cameras tab. The Cameras page appears.
CAMERAS TAB
PHYSICAL NUMBER
LOGICAL NUMBER
DESCRIPTION
CM9760-CC1 PORT
6800 MONITOR OUTPUT
Figure 60. CM9760-MGR Cameras Page
Complete the following steps for each CM6800E-48X8 tie line:
2. In the list of Defined Cameras, click the Physical Number (the number of the CM9760-MXB port used for connecting the tie line from the
CM6800E-48X8).
3. Enter a 0 in the logical number field.
4. If desired, enter a description in the description field.
5. Enter the sercomm port number on the CM9760-CC1 to which the CM6800E-48X8 is connected.
6. Enter the appropriate value in the Port Addr field, depending on the CM9760-MGR software version level:
•
If the CM9760-MGR software is version 7.08.029 or lower, enter 0.
•
If the CM9760-MGR software is version 8.03.006 or higher, enter the number of the CM6800E monitor output used to connect the tie
line to the CM9760-MXB. Note that you must use the monitor outputs in sequential order, starting with monitor output 1.
7. Save the changes (you must save changes for each tie line, before programming the next tie line).
C1528M-G (9/06)
79
Program the Link Cameras File
1. Click the Link Cameras tab. The Link Cameras page appears.
LINK CAMERAS TAB
LINK CAMERA NUMBER
LOGICAL NUMBER
DESCRIPTION
CC1 PORT NUMBER
CAMERA PORT ADDRESS
(6800 PHYSICAL
CAMERA NUMBER)
OPERATOR ACCESS
Figure 61. CM9760-MGR Link Cameras Page
Complete the following steps for each CM6800E-48X8 camera:
2. In the list of Link Cameras, click one of the available Link camera numbers.
•
If the CM9760-MGR software is version 7.08.029 or lower, you must use the link camera numbers in sequential order.
•
If the CM9760-MGR software is version 8.03.006 or higher, you can use the link camera numbers in non-sequential order.
3. Enter a unique logical number in the logical number field. This number is used by the CM9760-KBD keyboard to call a camera connected to
the CM6800E.
4. If desired, enter a description in the description field.
5. In the Port Num field, enter the sercomm port number on the CM9760-CC1 to which the CM6800E is attached. The port number is the same
for all link cameras connected to a particular CM6800E.
6. In the Port Addr field, enter the camera’s port address. This is the physical number of the camera connected to the CM6800E-48X8 rear
panel. In a 48 x 8 system, this number is between 1 and 48; in a 96 x 16 system, this number is between 1 and 96.
•
If the CM9760-MGR software is version 7.08.029 or lower, use the cameras in sequential order.
•
If the CM9760-MGR software is version 8.03.006 or higher, you can use non-sequential cameras.
7. Click the Oper Acc button to allow appropriate operator access. Refer to the CM9760-MGR Installation/User Manual for instructions on
configuring operator access.
8. Save the changes (you must save changes for each Link camera, before programming the next Link camera).
80
C1528M-G (9/06)
Program the Alarms File
This procedure is optional.
1. Click the Alarms tab. The Alarms page appears.
ALARMS TAB
PHYSICAL NUMBER
LOGICAL NUMBER
DESCRIPTION
DWELL
TIME
ALARM OPERATOR
CAMERA ACCESS
Figure 62. CM9760-MGR Alarms Page
Complete the following steps for each CM6800E-48X8 alarm:
2. In the list of Defined Alarms, click the Physical Number. This number must match the
CM6800E Logical Alarm Number assigned to the alarm contact.
3. Enter the CM6800E Logical Alarm Number in the logical number field. This number is
used by the CM9760-KBD keyboard to arm or acknowledge an alarm.
4. If desired, enter a description in the description field. This text flashes on the
CM9740/CM9760 system monitor screen when the alarm is triggered.
5. Enter a dwell time. This sets the amount of time each camera appears on a monitor
before the next camera is displayed.
6. Set at least one camera to display on the CM9740/CM9760 system for each alarm.
Click the Alm Cam button to open the Alarm Camera Switches dialog box, and then
enter a camera number in the Logical Cam Num field. You can enter up to five
cameras, and they can be any combination of CM9740/CM9760 system cameras and
CM6800 system cameras (Link cameras). If desired, enter a preset number in the
Preset Num field.
7. Click OK to close the Alarm Camera Switches dialog box.
Figure 63. Alarm Camera Switches Dialog Box
8. On the Alarms page, click the Oper Acc button to allow appropriate operator
access. Refer to the CM9760-MGR Installation/User Manual for instructions.
9. Save the changes (you must save changes for each alarm, before programming the next alarm).
C1528M-G (9/06)
81
NAVIGATE WITH THE CM9740/CM9760 KEYBOARD
When using the CM6800E as a satellite device in a CM9740/CM9760 system, you can navigate the CM6800E programming screens from the
following keyboards:
•
a local keyboard connected to the CM6800E-48X8 – either a KBD100/200A/300A Series keyboard or a KBD960/KBR960 Series keyboard;
navigation instructions are provided in the Programming the CM6800E section.
•
a CM9740/CM9760 system keyboard connected to the CM9740/CM9760-CC1 – either a CM9760-KBD or CM9760-KBR keyboard; most of
the CM9740/CM9760 keyboard instructions are identical to the KBD960/KBR960 keyboard instructions provided in the Programming the
CM6800E section. The following navigation instructions are unique to the CM9740/CM9760 keyboard.
How to Display the CM6800E Programming Main Menu
M9740/CM9760 System Keyboard
1. If the Camera menu appears, press
to exit).
2. If you have not already done so, select the monitor.
3. Switch to a CM6800E camera.
4. Select
DEF
.
5. Enter the Define PIN (Default: 1234), and then select
MENU
.
6. Press 89, and then select the Preset button or the Set Preset icon.
7. The CM6800E Main Menu appears.
PELCO SWITCHER
MODEL CM6800E
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 SYSTEM
15 ABOUT CM6800E
ENGLISH
RETURN
Figure 64. CM6800E Main Menu
How to Exit Programming Mode
M9740/CM9760 System Keyboard
• Press 89 Preset.
How to Select a Numerical Value in an Option Field
M9740/CM9760 System Keyboard
• Use the Open and Close keys to increment/decrement a number by 1.
• Use the Near and Far keys to increment/decrement a number by 10.
• Use the In and Out keys to increment/decrement a number by 100.
82
C1528M-G (9/06)
LOGICAL NUMBER ASSIGNMENT TABLE – FOR LINK CAMERAS
Link Camera Name
C1528M-G (9/06)
Link Camera Number in the
CM9740/CM9760 System
(Link Camera page:
“Phy Num” column)
Physical Camera Number on the
CM6800E-48X8
(Link Camera page:
“Port Addr” field)
CM9740/CM9760-CC1
Port Number
(Link Camera page:
“Port Num” field)
83
ASCII OPERATING COMMANDS
ASCII protocol uses the ASCII character set to transmit and receive commands between an ASCII device (such as a personal computer or ASCII
keyboard) and the CM6800E.
The ASCII protocol communicates in a standard asynchronous, byte-oriented protocol that includes: 1 start bit, 8 data bits, 1 parity bit (odd
parity), and 1 stop bit. The default communication rate is 9600 baud.
A lowercase “a” ends each command. The ASCII translator acknowledges accepted commands and rejected commands with the following
responses:
AKa
NAa
command accepted
command rejected or the ASCII translator does not recognize the command
If the command requires a numeric value, enter the number first.
Table I provides examples of ASCII commands. Table J lists all of the commands.
Table I. Examples of ASCII Commands
Functional Procedure
Commands
Result
Select a pan and tilt device labeled “CAMERA # 16” and
switch it to monitor # 3.
3Ma16#a
Switch camera 16 to currently selected monitor 3.
Manipulate the pan and tilt device.
1Ma3#a
Switch camera 3 to monitor 1.
5Ma2#a3\a
Go to camera 2, preset 3, on monitor 5.
47Ra33Da
Pan right at speed 47, tilt down at speed 33.
sa
Stop all image motion.
Switch a camera.
1Ma3#a
Switch camera 3 to monitor 1.
Call a preset.
5Ma2#a3\a
Go to camera 2, preset 3, on monitor 5.
Pan and tilt.
47Ra33Da
Pan right at speed 47, tilt down at speed 33.
Number ranges are enclosed in brackets – do not enter the brackets. When you control a fixed speed pan and tilt, omit the speed information.
NOTE: In a 96 x 16 system the numbers for cameras, monitors, alarms, and relays can be doubled.
Table J. ASCII Commands
Desired Action
Command
Result
Select monitor
[1-9999]Ma
Calls a monitor to use for camera operation.
Select camera
Next camera
Previous camera
[1-9999]#a
+a
-a
Selects a camera to display on the current operating monitor. The NEXT key (+) and PREV
key (-) commands switch to the next numbered camera in the system.
Start a sequence forward
[1-99]qa
Starts the selected sequence going forward (incrementing camera numbers).
Start a sequence backward
[1-99]ba
Starts the selected sequence going backward (decrementing camera numbers).
Hold a sequence
ea
Places the running sequence on hold, freezing the currently selected camera on the
monitor. It lets you control the camera or switch. The sequence is still “armed” on the
monitor, but inactive.
Hold a macro
[1-64]ea
Places the running macro on hold.
(Continued on next page)
84
C1528M-G (9/06)
Table J. ASCII Commands (Continued)
Desired Action
Command
Result
Pan left
Pan right
Stop pan left
Stop pan right
[1-64]La
[1-64]Ra
~La
~Ra
Moves the currently selected pan and tilt device left or right at the speed indicated. If
you omit the speed, some devices move at their default speed and others move at their
slowest possible speed. Speed information has no effect on fixed speed devices.
Tilt up
Tilt down
Stop tilt up
Stop tilt down
[1-63]Ua
[1-63]Da
~Ua
~Da
Moves the currently selected pan and tilt device up or down at the speed indicated. If
you omit the speed, some devices move at their default speed and others move at their
slowest possible speed. Speed information has no effect on fixed speed devices.
Zoom telephoto
Zoom wide
Stop zoom telephoto
Stop zoom wide
Ta
Wa
~Ta
~Wa
Makes the currently selected camera zoom in (close up view) or zoom out (wide view).
Focus near
Focus far
Stop focus near
Stop focus far
Na
Fa
~Na
~Fa
Changes the good focus range nearer or farther on the currently selected camera.
Iris open
Iris close
Stop iris open
Stop iris close
Oa
Ca
~Oa
~Ca
Opens (brighter image) or closes (darker image) the iris on the currently selected camera.
Stop all PTZ motion
sa
Stops all image motion (stops pan, tilt, zoom, focus, and iris). Does not stop a pattern.
Record pattern
Execute pattern
End pattern
[1-99]/a
[1-99]pa
[1-99]na
On receivers that do patterns, these commands let you record your motions and
operations (for a limited time) and then have the system repeat them.
Go to preset position
[1-99]\a
Recalls a stored preset position.
Set preset with a label
la[string]!a
[1-9999]^a
Sets a preset location with an embedded label, where the ASCII string must be
UPPERCASE characters.
The [string] is an alphanumeric label up to 20 characters long and [1-9999] is the
associated preset number.
NOTE: All transmitted characters must be ASCII.
Set preset without a label
[1-9999]-^a
Sets a preset location without an embedded label.
Begin zone
[1-8](a
Begins a zone without a label.
Begin zone with a label
la[string]!a[1-8](a
Begins a zone with an embedded label. The ASCII string must be uppercase characters.
End zone
[1-8])a
Ends the zone program
Begin random scan
Begin frame scan
Stop scan
[email protected]
[email protected]
[email protected]
These commands start and stop scans.
Auxiliary on
Auxiliary off
[1-256]xa
[1-256]~xa
Auxiliaries are relay outputs that can be controlled through the protocol 1-3 operate the
AUX 1-2 and F3 auxiliaries on the rear panel of the CM6800E (and the first three
auxiliaries on an external REL2064). 4-256 operate the external auxiliaries on up to four
REL2064 Relay Interface Units.
Camera auxiliary on
Camera auxiliary off
[1-8]Aa
[1-8]Ba
Operates auxiliaries at the camera (receiver).
Start macro
[1-64]Sa
Starts the selected macro.
Stop macro
[1-64]Ha
Stops the selected macro.
(Continued on next page)
C1528M-G (9/06)
85
Table J. ASCII Commands (Continued)
Desired Action
Command
Result
Acknowledge alarm
[1-9999]Ia
Acknowledges an existing alarm.
Arm internal alarm
Arm external alarm
Arm video loss alarm
Disarm internal alarm
Disarm external alarm
Disarm video loss alarm
[1-8]Jia
[1-256]Jea
[1-48]Jva
[1-8]~Jia
[1-256]~Jea
[1-48]~Jva
These commands arm and disarm system alarms.
Trigger an alarm
Clear an alarm
Acknowledge an alarm
#Ea
#Ia
#Ka
An ASCII device can send these commands through the CM6800E to control alarms in an
external alarm device, such as an ALM2064 Alarm Interface Unit.
An alarm is triggered
An alarm is cleared
An alarm is acknowledged
#Ea
#Ia
#Ka
If you configure a CM6800E port to report alarms to an ASCII device, the CM6800E
reports the alarm information using these commands.
Select a MUX camera
Display picture-in-picture
view
Display four-camera mode
Display nine-camera mode
Display 16-camera mode
Digital mode zoom
Digital mode pan left
Digital mode pan right
Digital mode tilt up
Digital mode tilt down
[1-9999]#m
im
Send camera title
[1-48]Ya[string]!a
NOTE: These commands do not affect internal alarms on the CM6800E rear panel.
NOTE: The alarm number (#) reported by the CM6800 is based on the logical alarm
number defined in the Logical Alarm Number screen. Refer to Assign a Logical Alarm
Number in the Alarm Programming section.
These commands control a Genex multiplexer connected to the CM6800.
um
om
xm
ym
dLm
dRm
dUm
dDm
Sends a camera title to the matrix switching system. You can only send one camera title
at a time.
Valid characters in the string are A-Z, a-z, space, and 0-9 in ASCII representation. Strings
are limited to 20 characters.
Version
va
Returns the version number of the device.
Set date and time
ZaMM/DD/YY/
HH:
MM:Ssa
Sets the date and time. Since the date and time string could be confused with other
commands, the command Za comes first. This puts the receiving device into a mode that
can accept the specialized string.
NOTE: All transmitted characters must be ASCII.
86
C1528M-G (9/06)
TROUBLESHOOTING
GAINING INITIAL CONTROL
If you are having problems gaining control of your system for the first time:
•
Confirm that all system equipment is plugged in and has power.
•
Confirm that each keyboard and peripheral device in your system has a unique local address. Refer to the Switch Settings section in the
appropriate keyboard manual.
•
Be sure data cables have not been mixed up.
•
Cycle the data cable to the keyboard:
1.
2.
3.
4.
Unplug the data cable from the rear of the keyboard.
Plug the data cable back into the rear of the keyboard.
WAIT AT LEAST FIVE SECONDS.
Select a monitor.
If you still cannot gain control of the system:
•
Confirm the wiring is correct and the user-supplied cable between wall jacks is appropriate for the application.
•
Confirm that when the keyboard data cable is cycled, the keyboard LED flashes momentarily (indicating power).
If you still cannot gain control of the system, call Pelco’s 24-hour technical support at 1800-289-9100 or 1-559-292-1981.
NOTE: There are no user-serviceable parts inside the CM6800E. Only authorized service personnel may open the unit.
C1528M-G (9/06)
87
SOFTWARE RESET
Pelco strongly recommends uploading system settings to the CM6800E-MGR before the software reset – this will allow you to restore system
settings after the software reset.
CAUTION: Resetting the software restores the system to default settings.
1. Remove the two screws and the DIP switch cover plate from the rear of the switcher.
010101
1 2 3 4 5 6 7 8
16
1
5
2
6
3
7
4
8
CONTROL
A T T
+ -
31
32
2
3
4
6
7
8
1
R R T T
- + + -
2
R R B
- +
F
3
1
120/230~
50/60 HZ
25 WATTS
DIP SWITCH
COVER PLATE
Figure 65. DIP Switch Cover Plate
2. Move DIP switch 7 to the ON position (to “0”).
3. Cycle power.
The switcher will go through a software clear cycle and reset to factory defaults.
4. Move DIP switch 7 to the OFF position.
Failure to move DIP switch 7 to the OFF position could result in loss of system settings during a power outage.
SWITCH 7:
ON = SOFTWARE RESET
OFF = NORMAL SYSTEM
OPERATION
Figure 66. CM6800E DIP Switch 7
5. Re-initialize keyboards by entering the monitor number and then pressing the MON key.
6. Download your previous system settings (revise settings as necessary) from the CM6800-MGR.
88
C1528M-G (9/06)
SOLUTIONS TO COMMON PROBLEMS
Refer to Table K for a list of common problems and their solutions.
Table K. Solutions To Common Problems
Problem
Remedy
CM6800E does not have power.
Make sure the power cord is plugged in.
You can see some cameras and not others from
your location.
Confirm that the camera is properly connected and has power.
The CM6800E does not respond to keyboard
commands.
Confirm that the monitor the keyboard is addressing is the same as the monitor in front
of you.
The keyboard and monitor may have been denied access to the cameras.
Access to that monitor may be restricted from that keyboard. Select another monitor.
Pressing the PGM key displays a P on the
keyboard LED, but the Password menu does not
appear on the monitor. (KBD100/200A/300A
Keyboards only)
Confirm that the keyboard transformer is plugged in and all electrical connections are
in order.
Keyboards do not function after installation and
initial power-up.
Confirm that all wiring is correct and that keyboards have power and are connected.
Previous system control has been lost.
SOLUTION 1
Confirm that the monitor the keyboard is addressing is the same as the monitor in front
of you.
Confirm that each keyboard has been set for a unique address.
Initialize the keyboard:
1. Enter the monitor number.
2. Press the MON key.
SOLUTION 2
1. Unplug the data cable from the rear of the keyboard.
2. Plug the data cable back into the rear of the keyboard.
3. Wait five seconds.
4. Re-initialize the keyboard.
SOLUTION 3
1. Power down the CM6800E.
2. Power up the system.
3. Wait five seconds.
4. Re-initialize keyboards.
SOLUTION 4
Perform a software reset (refer to Software Reset in this section).
CAUTION: Resetting the software restores the system to default settings. All user
programming is lost. Uploading system settings to the CM6800-MGR before the
software reset allows you to restore system settings after the software reset.
SOLUTION 5
Call Pelco’s 24-hour technical support at 1-800-289-9100 or 1-559-292-1981.
The unit malfunctions and you cannot restore it
to satisfactory operation.
C1528M-G (9/06)
Perform a software reset (refer to Software Reset in this section).
CAUTION: Resetting the software restores the system to default settings. All user
programming is lost. Uploading system settings to the CM6800-MGR before the
software reset allows you to restore system settings after the software reset.
89
KBD960/KBR960 ICON/BUTTON LEGEND
LOG
OFF
LOG
OFF
JSTK
JOYSTICK
ADJUST
4
AUX 4, RELAY 4
MUX
QUAD
YES
LOG OFF
YES
ADV
ADVANCE
MENUS
5
AUX 5, RELAY 5
MUX
NINE
NO
LOG OFF
NO
SERIAL PORT
TEST
6
AUX 6, RELAY 6
MUX
SIXTEEN
PIN
SETUP/DEFINE
PIN
KEYBOARD
DOWNLOAD
7
AUX 7, RELAY 7
MUX
LIVE
SAVE
SELECTION
KEYBOARD
UPLOAD
8
AUX 8, RELAY 8
MUX
CAMERA CONTROL
DEL
DELETE
G0
TEST GRAPHIC
PAGE 0
RESET
ALARM
SEQ
SEQUENCE
MENU
MORE
MENU
G1
TEST GRAPHIC
PAGE 1
RESET
ALL ALARMS
PRST
CAMERA
PRESET
EXIT
G2
TEST GRAPHIC
PAGE 2
MUTE
PATTERN
CAMERA
SELECTION
T0
TEST TEXT
PAGE 0
ALARM
ZONE
MONITOR
SELECTION
PARITY
SCROLL UP
SCROLL FIELD UP
DIP SWITCH
TEST
MTRY RELAY
DISPLAY
BRIGHTNESS
MAC
SCROLL DOWN
SCROLL FIELD DOWN
LCD
GPI
DEF
DEFINE
MENU
PGM
PROGRAM
MENU
MACRO
SELECT
DEF
NUM
DEFINE
NUMBER
MENU PROGRAMMING
GPI
MENU
MOMENTARY
PLAY FWD
SCROLL RIGHT
COM1 COM PORT 1
DEVICE
PAUSE
PLAY BWD
SCROLL LEFT
COM2 COM PORT 2
STOP
SCROLL OPTION
UP
COM3 COM PORT 3
MUX
MENU
MUX
MENU
SCROLL OPTION
DOWN
1
AUX 1, RELAY 1
MUX
TAPE
KEYBOARD
SELECT
2
AUX 2, RELAY 2
MUX
ZOOM
KEYBOARD
KEY TEST
3
AUX 3, RELAY 3
MUX
PIC IN PIC
IN/OUT
FUNCTION
CONTROLS
FORWARD
BACKWARD
RECALL/ALTERNATE
RUN
MACRO
PRESET/LOCK
IRIS
CONTROLS
NEAR/FAR
OPEN/CLOSE
OTHER
CONTROLS
CAMERA
TURBO
MONITOR
ESCAPE
00665
Figure 67. Icon/Button Legend
90
C1528M-G (9/06)
UPGRADE THE CM6800 SWITCHER SOFTWARE
When you expand a CM6800E-48X8 system to a 96 x 16 system, verify that all system software is up-to-date and in the appropriate
configuration. CM6800E-48X8 software includes both the CM6800E-48X8 switcher software and the CM6800- MGR software.
VERIFY THAT EACH CM6800E-48X8 UNIT CONTAINS THE SAME LEVEL OF SOFTWARE
To determine switcher software version, select “About CM6800” from the CM6800 Programming Main Menu. Verify the version level for each
CM6800E-48X8 unit. If one unit contains a lower software level, complete the following steps to upgrade the unit:
1. Connect a PC to the CM6800E unit (Note: you cannot connect a PC to the “Expansion” unit; if this is the unit to be updated, disconnect it
from the “Main” unit before connecting the PC).
Refer to Connecting a PC in the Installation section for instructions.
2. Insert the CM6800 Resource CD into the CD drive on the PC.
3. When the CM6800 Resources window appears, click Utilities.
4. On the Utilities page click the link to download the current CM6800E-48X8 software.
5. Follow the instructions provided on the screen during the download. For additional instructions, open the file named ReadMe.txt provided
on the CM6800 Resource CD in the Utilities folder.
NOTE: If you have previously used the CM6800-MGR software in a 48 x 8 configuration, you must uninstall and then reinstall the software
before you can use it in a 96 x 16 configuration. Refer to the CM6800-MGR Installation/Operation manual, or the CM6800-MGR online help for
instructions.
DOWNLOAD CURRENT SOFTWARE
TO THE SWITCHER
DATA CABLE
VIDEO RIBBON CABLE
CM6800E-48X8 MAIN UNIT
CM6800E-48X8 EXPANSION UNIT
TO UPDATE SWITCHER SOFTWARE
IN THE EXPANSION UNIT, DISCONNECT
THESE CABLES AND CONNECT THE PC
DIRECTLY TO THE EXPANSION UNIT.
Figure 68. Upgrade the CM6800 Switcher Software
C1528M-G (9/06)
91
Glossary
92
Access
The CM6800E allows you to restrict system control by (1) limiting the monitors or cameras a
keyboard can access, or (2) limiting the cameras that can be viewed on a monitor.
Alarm display format
The CM6800E Matrix Switcher provides four formats for displaying alarmed cameras on system
monitors: Block Build, Chronological Pair, Reverse Chronological Pair, and Salvo Group.
Alarm group
To display on a monitor, an alarm must be assigned to one or more alarm groups. The
CM6800E-48X8 Matrix Switcher provides eight alarm groups (A through H). The CM6800-32X6
Matrix Switcher provides six alarm groups (A through F). Refer to Program Alarm Groups and Alarm
Group Display Options.
Alarm priority
A priority alarm appears on system monitors before a non-priority alarm.
ASCII
The binary, 7-bit, 128-character set implemented as the standard in communications.
Auxiliary
Output relays can be used to control external devices based on matrix switcher activities. External
devices can include VCRs, alarm devices, and triggers for audio circuits.
Baud rate
In video, the greater the speed, the larger amount of information passed. In digital systems, this
capacity is given in bits per second, or baud rates.
Bit
An abbreviation for “binary digit” – the smallest unit of information a computer can use. A bit is
either a 1 or a 0 (a high or low voltage state).
Byte
An abbreviation for “binary term” – bytes are strings of bits, operated upon as a unit. A byte is
equal to eight bits (256 possibilities) and is large enough to hold one character (like an “A” or the
number “1”.)
Camera auxiliary
Some cameras contain an auxiliary output relay, which can be used to operate a device connected to
the relay.
Coaxitron
This is Pelco’s “up the coax” control technology. Control signals are sent back up the coaxial cable
that the video signal travels down on.
COM port
This is a communication port input on the rear panel of the matrix switcher.
Cross-point video matrix switcher
A matrix switcher that can select any video input onto any video output at any time.
Daisy-chain
This is a way of providing multiple connections in a series, from one source. A daisy-chain
configuration connects multiple, linked devices from one output. When connecting PTZ cameras to a
matrix switcher, for example, one set of cables connects the matrix switcher to each receiver, and
then each receiver is connected to the next receiver.
Dwell
This is the amount of time something happens in the system, such as the amount of time a camera
view displays on a monitor, or an auxiliary is on.
Event timer
The matrix switcher can automatically initiate macros or sequences based on time and date.
Extended Coaxitron
This is Pelco’s Coaxitron control technology that uses 32 bits to send a command.
Frame scan
A three-second camera scan (pan) followed by a three-second pause.
Latching operation
The auxiliary device remains on until a command is given (by a system operator or system
automation) to turn it off.
Logical camera number
A user-selectable, variable number, which is associated with an actual physical camera input on the
rear panel of the matrix switcher.
Macro
A sequence of commands or steps. Macros can be operated automatically or manually. Automatic
operation can be based on specific times or dates (set through the Event Timer).
C1528M-G (9/06)
Matrix switcher
This is also known as a cross-point switcher. The cross-points are actually electronic switches that
select any video input onto any video output at any one time, preserving the video impedance
matching. One video signal can simultaneously be selected on more than one output. More than one
video input can be selected on one output, in a sequential switching between inputs (unless the
input is routed through a multiplexer, which allows more than one input to be viewed on the output
monitor at any one time).
Momentary operation
The auxiliary output operation is activated briefly and then turns off.
Multiplexer (MUX)
A multiplexer allows an operator to view more than one video signal (usually either four, nine or
sixteen signals) at one time on a single monitor. A multiplexer can also send these multiple images
to the video recorder, switching rapidly between image from each camera.
NTSC
The American color TV standard, used in North America, Japan, and a few other countries. It
specifies 525 lines/screen, and 29-30 frames/sec.
Null modem cable
A null modem cable allows you to connect your PC to another nearby PC or serial device by “crossing
over” (reversing) their respective pin contacts. (A null modem cable is limited to 30 feet in length.)
PAL
The color TV standard (50Hz) used by European, Asian, and some Latin American countries. It
specifies 768 pixels/line, 576 lines/screen and 25 frames/sec.
Parity type
The parity bit is used to identify whether the bits being moved arrived successfully. Parity bit
checking can be based on odd or even bits. No parity means that a parity bit is not transmitted or
checked.
Partitioning (access)
The CM6800E allows you to restrict system control by (1) limiting the monitors or cameras a
keyboard can access, or (2) limiting the cameras that can be viewed on a monitor.
Pattern
A pattern is a user-defined, viewable camera path with a definite beginning and end. The pattern
can consist of any standard pan and tilt or lens command. Once defined, the pattern is easily
activated by a system operator or through an automated event. The pattern will run continuously
until it is deactivated. The number and time length of patterns varies with different positioning
systems.
Physical input
A number representing an actual BNC camera input on the rear panel of the matrix switcher. This
number cannot be changed.
Preset
A preset allows operators to direct a PTZ (camera positioning system) to move to a predetermined
scene on keyboard command or as a result of an alarm. In addition to moving the camera, a
descriptive title can appear on the screen. The type of camera positioning system determines the
number of presets available.
Priority control
This is the level of priority a system keyboard has to control a PTZ camera positioning system and to
access CM6800E Matrix Switcher on-screen programming menus.
PTZ
This is a camera positioning system with pan, tilt, and zoom capabilities.
Random scan
This is a camera scan moving in a random pattern.
RJ-45 wall block
This is a wall block with eight terminals for connecting RS-232, RS-422, and RS-485 communication
lines. (This is Pelco part number CON12J00820360Z.)
RS-232
This is an Electronics Industry Association (EIA) interface standard used for data communication; the
normal connection distance is 50 feet (15 m). Pelco uses this standard for communication from a
controller to a PC or RS-232 network. The Pelco three-wire connection provides one wire for
transmit, one wire for receive, and one wire for common.
C1528M-G (9/06)
93
RS-422
This is an Electronics Industry Association (EIA) interface standard. Pelco uses this standard for
communication from a controller to one or more camera receivers (on the same line); the maximum
recommended distance is 4,000 feet (1,219 m).
The four-wire connection provides two wires for transmit and two wires for receive. Pelco receiver/
driver communication uses only the two transmit wires (commands are sent from the controller to
the receiver only; the receiver does not “talk” back to the controller). Pelco keyboard communication
uses all four wires.
NOTE: The electrical communication scheme used by Pelco is a direct-coupled method, not an
AC-coupled method. Therefore, if the ground potential of the wire at its two end points is different
(other than zero volts), an additional wire is required as a ground.
RS-485
This is an Electronics Industry Association (EIA) interface standard used for communication between
multiple transmitters and receivers; the maximum recommended distance is 4,000 feet (1,219 m).
The four-wire connection provides two wires for transmit and two wires for receive.
NOTE: The electrical communication scheme used by Pelco is a direct-coupled method, not an
AC-coupled method. Therefore, if the ground potential of the wire at its two end points is different
(other than zero volts), an additional wire is required as a ground.
94
Scratchpad sequence
A scratchpad sequence can be run on an individual system monitor, without entering the
password-protected CM6800E Matrix Switcher on-screen programming menus. You can program
scratchpad sequences from the CM6800E Matrix Switcher on-screen programming menus only, not
from the CM6800-MGR software.
Sequence
Allows an operator to see a routine of 72 camera views on any system monitor, over and over again.
The sequence can be operated automatically or manually. The order in which the camera views
appear and the time each view remains can be programmed.
Standard Coaxitron
This is Pelco’s Coaxitron control technology that uses 15 bits to send a command.
Star configuration
This is a way of providing multiple direct connections from one source. A star configuration uses a
separate cable for each direct connection, with all of the cables connected to a central device.
When connecting PTZ cameras to a matrix switcher, for example, the central device can be a code
distribution unit, such as the CM9760-CDU-T. Each camera has a direct connection to the
CM9760-CDU-T, which is the central device.
Synchronize
Since the CM6800E Matrix Switcher can be programmed from either the CM6800-MGR software or
the CM6800E Matrix Switcher on-screen programming menus, you could potentially have different
settings in the two programming sources. Pelco recommends transmitting any programming
changes from the updated programming source so that the next time you make changes from either
programming source, you will be modifying the current system settings. Refer to Transmit
Programming Settings in the CM6800-MGR Installation/Operation manual.
System keyboard
This is a keyboard compatible with and connected to the matrix switcher, allowing a system
operator manual control over the system.
System reset
This restores the system to the default settings, as shipped from the factory.
Vertical drive/synchronization
This option sends a timing pulse from the matrix switcher to a compatible camera. The camera
aligns the vertical synchronization with the timing pulse.
Zone
A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is
associated. When the associated camera is panned through or remains within this defined zone, the
zone label appears on the monitor. With some camera systems, a zone can be blanked to prevent
viewing while the camera is positioned in the zone.
C1528M-G (9/06)
Specifications
GENERAL
Memory Protection
Keyboards
Receiver/Dome Control
Alarm Inputs
Control Outputs on Rear Panel
AUX 1, 2
F3
Additional Outputs
Communication Ports
Lithium battery, five years of data protection
Eighteen: Sixteen KBD100/200A/300A Series keyboards and two KBD960/KBR960 Series keyboards. (Switcher
can provide power for two KBD100/200A/300A Series keyboards. Additional keyboards will require a remote
power supply.)
Coaxitron and RS-422
Eight individually programmable for N.O. or N.C. on rear panel (plus an additional 256, via ALM2064, Alarm
Interface Units)
Two relays (SPDT), rated at 0.5 amp @ 125 V, 1 amp @ 30 VDC, 60 milliohms contact resistance
One open collector (TTL); 15 VDC maximum, 25 mA maximum
Four REL2064, Relay Interface Units, may be connected to expand relay outputs to a maximum of 256
Eight data ports, two PTZ control ports, all programmable by the user; two ports provide power for keyboards
ELECTRICAL
Input Power
Power Consumption
120 V or 230 V, 50/60Hz
25W
SWITCHER CHARACTERISTICS
Video Inputs, Looping
Video Inputs, Terminating
Video Outputs
Switching Type
Switching Method
Switching Time
40 BNC, terminating or looping (individually selectable per camera), .5 to 2.0 Vp-p composite video, video loss
detection
Eight, BNC, terminating, .5 to 2.0 Vp-p composite video, video loss detection
Eight outputs, BNC
Cross-point video matrix, NTSC and PAL compatible
Vertical interval switching
Less than 16 milliseconds (typical)
VIDEO
Bandwidth
Frequency Response
Signal-to-Noise Ratio
Adjacent Channel Crosstalk
Differential Gain
Differential Phase
Gain
DC Output
15 MHz
Flat to 8 MHz, ±1dB to 13 MHz
-50 dB (peak-to-peak vs. RMS noise)
-55 dB typical at 3.58 MHz
0.03% typical
0.24° typical
Unity (±1dB)
Zero volts
CHARACTER GENERATION
Character Type
Camera Identification
Programmable
White with black outline; adjustable brightness
Two lines, twenty-character title, plus camera number, monitor number, date (four formats) and time (24-hour or
AM/PM formats)
On-screen, menu-driven
ENVIRONMENTAL
Ambient Operating
Temperature
Humidity
20° to 120°F (-7° to 49°C)
10-90% non-condensing
MECHANICAL
Dimensions
Mounting
Unit Weight
17.40" (W) x 5.25" (H) x 12.25" (D) inches (without rack ears)
(44.20 x 13.34 x 31.12 cm)
Factory-configured for EIA rack mount (3 RU); rack ears can be removed for versatile wall mount or freestanding
applications
12.7 lb (5.76 kg)
(Design and product specifications subject to change without notice.)
C1528M-G (9/06)
95
Regulatory Notices
48 x 8 System
In a 48 x 8 system, this equipment complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.”
This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
96 x 16 System
In a 96 x 16 system, this equipment complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
96
C1528M-G (9/06)
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
• Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted
pair transmission products.
• Three years on Genex ® Series products (multiplexers, server, and keyboard).
• Three years on Camclosure ® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
• Three years on PMCL200/300/400 Series LCD monitors.
• Two years on standard motorized or fixed focal length lenses.
• Two years on Legacy ®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
®
®
™
• Two years on Spectra , Esprit , ExSite , and PS20 scanners, including when used in
continuous motion applications.
• Two years on Esprit ® and WW5700 Series window wiper (excluding wiper blades).
• Two years (except lamp and color wheel) on Digital Light Processing (DLP ®) displays.
The lamp and color wheel will be covered for a period of 90 days. The air filter is not
covered under warranty.
• Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura ™ Series distributed network-based video products.
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such
Products. In no event will Pelco be liable for any special, incidental or consequential damages
(including loss of use, loss of profit and claims of third parties) however caused, whether by
the negligence of Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product when
returned.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C1528M
C1528M-A
C1528M-B
C1528M-C
C1528M-D
Date
11/02
3/03
4/03
5/03
6/04
C1528M-E
2/05
C1528M-F
C1528M-G
6/05
9/06
Comments
Original version.
Updated to describe revised satellite functionality (at the 3.01 software level).
Software updated to 3.02 level.
Software updated to 3.03 level; revised report alarms description; added instructions on updating switcher software.
Removed reference to use 18-gauge wire for EIA RS-485 communication. Updated Important Safeguards and Warnings. Revised Tables B, G, and J, and Figures 52
and 64.
Added information on using the CM6800E as a satellite device in a 9700 System (as a result of CAR 050103). Added information on new feature allowing the use of
macros for up to three alarm steps and revised memory protection timeframe (as a result of ECO 04-10477). Revised Figure 16 and replaced Figure 22 with previous
version from C1528M-C.
Revised 96 x 16 configuration connection instructions (as a result of ECO 03-9568 / CAR 031201).
Revised Access screen graphic and instructions to reflect new PTZ time out functionality (as a result of ECO 06-15055).
Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
DLP is a registered trademark of Texas Instruments, Inc.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries.
©Copyright 2006, Pelco. All rights reserved
®
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
Australia
| Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherlands | United Arab Emirates | United Kingdom | United States