Download BSF1614CR-CN

pure indoor living
16-inch (40cm)
Stand FAN
MODEL: BSF1614 Series
Instruction Leaflet
Read instructions before operating. Retain for future reference.
Questions? Comments? Call 1-800-253-2764 in North America
or visit our website at www.bionairecanada.com.
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
Whenusingelectricalappliances,basicsafetyprecautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse
unit, plug or cord in water or spray with liquids. Plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used by or near children.
5. Unplug from outlet when not in use, when moving
fan from one location to another, before putting on
or taking off parts and before cleaning.
6. Avoid contact with moving parts.
7. DO NOT operate in the presence of explosives and/or
flammable fumes.
8. To avoid fire hazard, NEVER place the cord under
rugs or any parts near an open flame, cooking or
other heating appliance.
9. DO NOT operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner.
10. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
tripped over.
11. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
12. DO NOT let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
13. DO NOT use outdoors.
14. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
15. Always use on a dry, level surface.
16. DO NOT operate fan until fully assembled with all
parts properly in place.
17. This product is intended for household use only and
not for commercial or industrial applications.
18. WARNING: To reduce the risk of electrical shock
and avoid injury to persons, DO NOT use your fan in
the window.
19. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
This product is for use on 120 volts. The cord has a plug (A) as shown. An
adapter (C) (not included) is available for connecting three-blade groundingtype plugs to two-slot receptacles (B). The green grounding lug extending
from the adapter must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be used if a three-slot
grounded receptacle is available.
CAUTION: Use Only with GFCI Protected Receptacles.
F E AT U R E S - O P E R AT I O N S
ASSEMBLY INSTRUCTIONS
3. Turn the L-shaped locking lever clockwise to securely
attach the pole to the base.
Assembly Time: 10-15 minutes.
4. Set the base on the floor.
Tools Required: Phillips head screw driver.
Fan Head Assembly
NOTE: MAKE SURE YOU REMOVE ALL CONTENTS FROM
THE PACKAGE. PLEASE CHECK PACKAGING MATERIALS FOR You are now ready to assemble the fan head.
PARTS THAT COULD BE REQUIRED TO OPERATE YOUR FAN. 1. Loosen the Rear Grill Securing Screw and Nut (E)
from the motor housing. Position the rear grill (F)
Base/Pole Assembly
over the motor shaft (G), making certain that the 2
You will need the base (P), lower outer pole (O), and
guiding posts at top of the rear grill centre aligns
L-shaped locking lever (Q).
with the 2 top holes on the outer ring of the motor
housing (J). First insert the 2 guilding posts into the 2
1. Insert the threaded end of the L-shaped locking lever
holes at top and pull down the 2 slots to lock in
into the hole through the base cover.
place. Then align the bottom screw post onto the
2. Whileholdingthebasecoverwithonehandvertically,
bottom hole and replace the rear grill securing screw
connect the outer pole to the base, sliding the
and nut (E) and tighten the screw.
L-shaped locking lever into the bottom of the outer
pole with your other hand.
Guiding
Posts
F
Fig. 1
G H I
C
D E
B
J
E
K
A
R
L
S
M
A. Logo Plate
2. Loosen the blade securing screw (R) on side of the
B. Front Grill
fan blade (D) to slide the fan blade onto the motor
C. Grill Clips (6)
shaft (G) through the rear protrusion. Make sure the
N
D. Fan Blade
blade securing screw (R) rest on the notch (flat side)
E. Rear Grill Securing Screw
of motor shaft and tighten the screw (R).
and Nut
O
CAUTION: Avoid contact with sharp end of blades.
F. Rear Grill
3. Remove the grill screw and nut located on the bottom
G. Motor Shaft
of the grill.
H. Speed Control Knob
4. Centre the front grill (B) by aligning the Bionaire®
I. Oscillation Knob
logo on the logo plate so that it is horizontal and
P
J. Motor Housing
parallel with the floor. Then place the bracket at the
K. Tilt Adjustment Knob
top over the front and rear grills with the hole on the
Q
L. Locking Screw and Nut
bracket going through the center vertical bar. Fasten
M. Inner Extension Pole
R. Blade Securing
the other clips, making sure they go over both the
N. Height Adjustment Collar
Screw
front and rear grills.
O. Lower Outer Pole
S. Grill Screw and Nut
5. Replace grill screw and nut (S) and tighten with screw
P. Base
driver.
Q. L-Shaped Locking Lever
F E AT U R E S - O P E R AT I O N S
Final Assembly
1. Slide the inner extension pole (M) up from the lower
outer pole (O), first loosening the height adjustment
collar (N). To securely hold this position, tighten the
height adjustment collar (N).
2. Place the fan head assembly into this extension pole,
inserting the fan’s head neck into the pole opening.
Lock the neck into the extension pole by using the
locking screw and nut (L) and secure tightly.
Height Adjustment
Follow these instructions to adjust the height of the fan.
1. Whileholdingtheinnerextensionpole(M)withone
hand, turn the height adjustment collar (N) counterclockwise to loosen the pole.
2. Adjust the pole to the desired height and firmly
tighten the height adjustment collar in a clockwise
direction.
OPERATING INSTRUCTIONS
CLEANING/MAINTENANCE INSTRUCTIONS
1. Set fan base on a dry, level surface.
2. Plug cord into any standard 120 volt AC outlet.
Please make sure the Speed Control Knob is in the
OFF (O) position. Speed Control Knob (H) is located
on the Fan Motor Housing.
3. The SPEED is adjusted by turning the Speed Control
Knob (H) to the desired setting, O-1-2-3.
4. The OSCILLATION control knob (I) is located on the
top of the Fan Motor Housing. To start Oscillation,
push Control knob down. To stop Oscillation, pull
Speed Control Knob up.
ADJUSTMENT INSTRUCTIONS
Tilt-Adjustment
Follow these instructions to tilt the Fan Head for upward
angle air movement.
1. To change the tilting angle of the fan head, simply
loosen the tilt-adjustment knob (K).
2. Move the fan head to the desired angle and firmly
tighten the tilt-adjustment knob to lock into place.
Follow these instructions to correctly and safely care for
your fan. Please remember:
FAN CLEANING
• Alwaysunplugthefanbeforecleaningor
disassembling.
• Donotallowwatertodriponorintothefanmotor
housing.
• Donotuseanyofthefollowingasacleaner:
gasoline, thinner, benzine.
Fan Blade Cleaning
1. To access the fan blade, remove the front grill and
securing screw.
2. Clean the fan blade, front and rear grills with a soft,
moist cloth.
3. Replace blade, tighten securing screw and securely
fasten the front grill (see detailed instructions in the
Fan Head Assembly section).
Fan Head, Base and Pole Cleaning
Using a soft, moist cloth, with or without a mild soap
solution, carefully clean the fan base, pole and head.
Please use caution around the motor housing area. Do
not allow the motor or other electrical components to be
exposed to water.
F E AT U R E S - O P E R AT I O N S
FAN STORAGE INSTRUCTIONS
Your fan should be stored in the off-season in its original
box. It is important to keep it in a safe, dry location.
• Werecommendusingtheoriginal(orappropriately
sized) box.
• Pleaseremembertoprotectthefanfromdustor
moisture.
If you have any questions regarding your product or
would like to learn more about other Bionaire®
products, please contact our Consumer Service
Department at 1-800-253-2764 or visit our website
at www.bionairecanada.com.
© 2013 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All rights reserved. Imported and
distributed by Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions, 20 B Hereford
Street, Brampton, Ontario L6Y 0M1.
Printed In China
WA R R A N T Y I N F O R M AT I O N
1 Y E A R L I M I T E D WA R R A N T Y
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of one year from
the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will repair
or replace this product or any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service
centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and
conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly,
repair or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not
cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
What are the limits on JCS’s Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a
particular purpose is limited in duration to the duration of the above warranty.
JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the
product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract,
fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
In the U.S.A.
If you have any questions regarding this warranty or would like to obtain warranty service, please call
1-800-253-2764 and a convenient service center address will be provided to you.
In Canada
If you have any questions regarding this warranty or would like to obtain warranty service, please call
1-800-253-2764 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located
in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any
other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO
NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.