Download Hawker SEA FURY

Thank you for choosing CYmodel
Global : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Hawker SEA FURY
Item Nr: Cy8029
Instruction Manual
Before commencing assembly,please read these instructions thoroughly.
SAFETY PRECAUTIONS
This radio control model is not a toy!
lFirst-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce
its performance to full extent.
lAssemble this kit only in places out of children ,s reach!
lTake enough safety precautions prior to operating this model.
,
You are responsible for this models ass embly and safe operation!
lAlways keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
lCould cause serious injury or even death
SPECIFICATION
Wing Span.......2420 mm (95.2 in)
Wing Area.......91.4 dm2(1418 sq.in)
Takeoff weight....9.4 kg
Length..............2204 mm (86.7in)
Engine..............100-150cc gas engine
Radio................6 channels, 10 servos
Designed and Manufactured by : CYmodel
Http : // www.cymodel.com
REQUIRED FOR OPERATION (Purchase separately)
A minimum 6 channel radio for airplanes (with 10 servos).
And dry batteries.
1
!
4
CAUTION: Only use a minimum 6 channel radio for
airplanes! (No other radio may be used!)
5
A minimum 6 channel
transmitter for airplanes.
Silicone Tube
Fuel Filter
Glow engine fuel only.
required for engine starting
!
WARNING: Normal gasoline cannot
be used with glow engines.
Fuel Pump
Plug Wrench
12 AA-size Batteries
For handing the radio properly.refer to its instruction manual.
36
Engine and Muffler
2
Glue
Model Airplane engine
100-150 cc gas engine
3
37
Ignition
Muffler
Epoxy Glue
Instant glue
Other equipment for enhancing
airplane operation & perormance
Purchase a propeller that
will match your engine
Propeller splinner
Engine Starter
12V Battery (for starter)
TOOLS REQUIRED ( Purchase separately)
Sharp Hobby Knife
Needle Nose Pliers
Phillips Screw Driver
Awl
Wire Cutters
Scissors
BEFORE YOU BEGIN
. Read through the manual before you begin ,so you will have an overall idea of what to do.
2 . Check all parts .if you find any defective or missing parts .contact your local deater.
3 . Symbols used throughout this instruction manual,comprise.
1
A
B
Apply epoxy glue.
Drill holes with the specified
Diameter(here:2mm)
Must be purchased
separately!
Apply instant glue
(CA glue,super glue).
Ensure smooth non-binding
movement while assembling.
Pay close attention
here!
Assemble left and right
Sides the same way.
Cut off shaded portion.
2mm
Cut off excess.
2
£¡Warning!
!
Do not overlook this symbol.
!
3
Accessory list for this page.
Apply instant type A/B glue to aileron and pin hinge
2.3x8mm Tp Screw
Make sure hings are
mounted in the same line
----4
Pin hings
---8
Hinge
A
-----8
B
Pin hings
-----------8
1
4
Install the navigation lights to the wing
Install the aileron
Aileron
Tie a weight to a piece of string.
Lower the string into the wing from
the root, Let the weight drop out
through the wing
.A
Tailing
edge
C
A
B
Warning!
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
2
5
Install the lamp-chimuey to the wings
Blcak line
Epoxy the flap to the wing as illustration
Battery
1.5V
1.5V
Red line
2.3x8mm
Tp Screw
A
--4
B
Hinge
--------8
3
8
Accessory list for this page.
!
Rod adjuster
Rod (2.5x100mm)
- - - 12
Connecting rod head
----6
---2
M3X35mm Screw
----4
M3X30mm Screw
Rod (2.5x85mm)
---4
----2
Rod adjuster
M2X8mm Screw
Horn
----6
----2
- - - - 12
- - - 12
Rod (2.5x100mm)
Horn
---2
M3X30mm Screw
- - - - 12
Connecting rod head
M4X35mm Screw
----6
----6
----2
M3X35mm Screw
---4
6
Install the nylon control horn and
connect the linkage
Rod (2.5x85mm)
---4
9
Assemble of the servo
----4
M3X30mm Screw
- - - - 12
M3X30mm Screw
----2
M2X8mm Screw
M4X35mm Screw
- - - - 12
---4
Install the nylon control horn and
connect the linkage
A
10
Epoxy the wheel wells to the holes
Trim the holes if necessary
2
Assemble of the servo
50
7
C.A
4
B
!
5X45mm Axletree
----2
3X20mm Tp screw
-----8
5.2mm Collar
-----2
3X3mm screw
-----2
4X4mm screw
-----2
Rod adjuster
-----1
2X8mm
Horn
screw
-----1
2000mm Air line
-----2
Make sure hings are
mounted in the same line
Rod adjuster
---4
Connecting rod head
----2
Retainer
-----1
M2X8mm Screw
----4
Rod (1.8X80mm)
-----1
M3X35mm Screw
----4
Pin hings
A
B
M3X30mm Screw
----6
Rod (2.5x85mm)
Epoxy pin hinges to elevator
----2
----2
----2
Pin hings
M4X35mm Screw
-----------6
----2
----2
11
13
Accessory list for this page.
14
Assemble of the landing gear
Epoxy elevator hinges to horizontal tail
A
5X45mm
B
Axletree
-----2
3X20mm Tp screw
-----8
5.2mm Collar
-----2
!£¡Warning!
3X3mm screw
-----2
Securely glue together ,if coming
off during . You will lose control
of your airplane which leads to accidents!
4X4mm screw
-----2
12
15
Two wheel retract system
Install the elevator servos
M3X35mm Screw
----4
M3X30mm Screw
Horn
2000mm Air line
Please insure the sealing of the retract
system before flight .
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
----2
-----2
Rod adjuster
-----1
Retainer
2X8mm
Rod (1.8X80mm)
screw
-----1
Connecting rod head
----2
M4X35mm Screw
----2
-----1
Rod adjuster
---4
-----1
5
----2
M2X8mm Screw
----4
----2
Rod (2.5x85mm)
----2
18
Accessory list for this page.
!
Install the tail wheel
M3X16mm Cap screw
Pin hings
- - - - -4
4
Horn
M4X45mm
----2
3X3mm Screw
----4
Connecting rod head
----2
3.2mm Nylon Collar
----1
----1
3.2mm Metal Collar
Screw
----3
-----1
----3
Rod adjuster
M2X8mm
Rod
-----1
3.2mm Nylon Collar
3.2mm Rocker
M3X35mm
----2
3.2mm Rocker
3X3mm Screw
----4
----3
M3X16mm Cap screw
4
Screw
------2
Screw
----2
Set Nut
-------3
10mm tube
------2
8mm prapilionaceous Nut
3.2mm Metal Collar
----3
16
-----4
19
Epoxy pin hings to rudder
Rudder . Connect the linkage
rod to the horn
Horn
Pin hings
----2
------4
Connecting rod head
----2
Make sure hings are
mounted in the same line
Rod adjuster
----2
Rod
------2
10mm tube
------2
M4X45mm
Screw
----3
M3X35mm
Screw
----3
M2X8mm
A
B
Screw
----2
Set Nut
-------3
20 Mount the main wing on the fuselage
Install the rudder
Tailing edge
8mm prapilionaceous Nut
-----4
4mm
17
Rudder
A B
Warning!
Securely glue together. If coming off during flights,you'll
lose control of your airplane which leads to accidents!
6
!
23
Accessory list for this page.
Assembly of the engine
Aluminium tube
M4X10mm screw
------2
- - - - 16
Aluminium tube
- - - - 16
3mm Blind Nut
- - - - - - - - - 12
M3X20mm screw
- - - - - - 12
21
A
24
Epoxy the horizontal tail to fuselage
B
Assembly of the engine
A
B
M4X10mm screw
------2
10mm
3mm Blind Nut
- - - - - - - - - 12
securely glue together,if coming off
during flights, you'll lose control of your
airplane which leads to accidents.
22
M3X20mm screw
- - - - - - 12
Assemble horizontal tail,vertical tail,
tail gear separately
A
A
A
25
A
Make sure to glue securely.
If not properly glued,a failure
in flight may occur
Securely glue together, If coming off
during flihts .you’ll lose control of your
airplane which leads to accidents!
Temporarily fasten down the main wing
and check its correct position.
7
Assembly of the engine
28 Assemble the servos and switch in the fuselage
Accessory list for this page.
!
Rod adjuster
-----2
Aluminium tube
-----2
2X8mm
screw
-----2
Rod
---2
M3X15mm screw
------5
3mm Washer
---------6
Rod adjuster
-----2
26
Epoxy the wheel wells to the holes
29
Trim the holes if necessary
Aluminium tube 2X8mm
-----2
screw
-----2
Rod
-----2
Trim the surplus shaded portion away from the canopy
After confirming the
position(see front of
fuel tank).
Insert and tighten
the screw.
3X20mm
Screw
----1
27
30
Assemble of the landing gear
Install the cowling
Fuel tank
M3X15mm screw
------5
3mm Washer
---------6
8
33
Adjustment.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
AILERON
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
Side view
75mm 75mm
AILERON
Adjustment.
Top view
85mm
FLAP
32
Adjustment.
34
95mm 95mm
31
Centre of Gravity.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the
receiver and battery.
Adjust the travel of each control surface to the
values in the diagrams.
These values fit general flight capabilities.
Readjust according to your needs and flight level.
80mm 80mm
170-180mm
ELEVATOR
!
Warning!
NEVER fly the model
without well balancing.
35
Centre of Gravity.
9
CG