Download SD-22VB SD-22VE SD-22VL

FILE NO. 810-200213
SERVICE MANUAL
TM
DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER
SD-22VB
SD-22VE
SD-22VL
OCT., 2002
Specifications
DVD PLAYER
GENERAL
Power supply:
Power consumption:
AC 230-240V 50Hz
Operation: 23W
Stand by: 7W
Weight:
4.5 kg
Dimensions:
Width : 430 mm
Height : 99 mm
Depth : 314.5 mm
Input Level:
SCART-socket: VIDEO: 1 Vp-p, 75 Ω
AUDIO: 500 mV, 50 k Ω
Audio IN jack: 500 mV, 50 k Ω
Output Level:
SCART-socket: VIDEO: 1 Vp-p, 75 Ω
AUDIO: 500 mV, 1 k Ω
Audio OUT jack: 500 mV, 1 k Ω
Hi-Fi Frequency Response: 20Hz to 20,000Hz
Hi-Fi Dynamic Range:
More than 75dB
VCR section
Video Head:
Audio Track:
Channel coverage:
RF Channel Output:
F.FWD/REW Time at 25˚C:
DVD section
Signal system:
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
Pickup:
ACCESSORIES:
SD-22VB
USER’S GUIDE
Hi-Fi VIDEO
CASSETTE
RECORDER
4 Rotary Heads
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
2-12, X, Y, Z, S1-S41, 21-69
UHF channel 36 (23 to 69)
Approx. 1minute and 48 seconds (with E-180 Cassette Tape)
PAL
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22KHz
CD: 4Hz - 20KHz
90dB
0.1%
Below Measurable Level
90dB
Audio : (RCA) 500 mV, 1Kohm
Digital Audio : 0.5Vp-p/75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
DIGITAL VIDEO
Remote control x 1
75 ohm Coaxial Cable x 1
Battery AAA x 2
2A7A101A K
02/06
Safety Precautions
Safety Precautions
SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT
SAFETY FIRST
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
IMPORTANT
Please read the various precautions on page 2 and 3 before installing or operating the recorder.
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in
any literary, dramatic, musical, or artistic work embodied therein.
CAUTION
When you are not using the recorder for a long period of time, it is recommended that you disconnect the
power cord from the mains outlet.
Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock
or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal
lead or aerial.
IMPORTANT
Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this
equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to
reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.
In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your
nearest dealer.
If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow the instructions given below:
DO NOT make any connection to the Larger Terminal coded E or Green.
The wires in the mains lead are coloured in accordance with the following code:
Blue to N (Neutral) or Black
Brown to L (Live) or Red
If these colours do not correspond with the terminal identifications of your plug, connect as follows:
Blue wire to terminal coded N (Neutral) or coloured Black.
Brown wire to terminal coded L (Live) or coloured Red.
If in doubt – consult a competent electrician.
The STANDBY/ON
button does not completely shut off mains power from the unit, but switches operating
current on and off. “ ” shows electrical power standby and “ I ” shows ON.
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a singlespeed video recorder.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under
extremely humid conditions-just as water droplets form in the surface of a glass filled with cold liquid. Moisture
condensation on the head drum will cause damage to the tape. In conditions where condensation may occur,
keep the recorder turned on for a few hours to let the moisture dry.
2
This equipment has been designed and manufactured to meet international safety
standards but, like any electrical equipment, care must be taken if you are to obtain the
best results and safety is to be assured.
**************
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and
inter- connections between the pieces of equipment) are properly made and in accordance
with the manufacturer’s instructions. Switch off and withdraw the mains plug before making
or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of
your equipment.
DO be careful with glass panels or doors on equipment
**************
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T obstruct the ventilation openings of the equipment with items such as newspapers,
tablecloths, curtains, etc. Overheating will cause damage and shorten the life of the
equipment.
DON’T allow electrical equipment to be exposed to dripping or splashing, or objects filled
with liquids, such as vases, to be placed on the equipment.
DON’T place hot objects or naked flame sources such as lighted candles or nightlights on,
or close to equipment. High temperatures can melt plastic and lead to fires.
DON’T use makeshift stands and NEVER fix legs with wood screws - to ensure
complete safety always fit the manufacturer’s approved stand or legs with the fixings
provided according to the instructions.
DON’T use equipment such as personal stereos or radios so that you are distracted from
the requirements of traffic safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your
hearing.
DON’T leave equipment switched on when it is unattended unless it is specifically stated
that it is designed for unattended operation or has a stand-by mode. Switch off using the
switch on the equipment and make sure that your family know how to do this. Special
arrangements may need to be made for infirm or handicapped people.
DON’T continue to operate the equipment if you are in any doubt about it working
normally, or if it is damaged in any way -switch off, withdraw the mains plug and consult
your dealer.
ABOVE ALL
—NEVER let anyone especially children push anything into holes, slots or any other
opening in the case - this could result in a fatal electrical shock;
—NEVER guess or take chances with electrical equipment of any kind
—it is better to be safe than sorry!
*************
3
Features
Contents
Video Cassette Recorder
• High Quality (HQ) Images
• On-Screen Displays (OSD)
• Nicam Hi-Fi Stereo Audio
Recording and Playback
• Auto TV Station Tuning and Auto
Clock Set
• 80 Memory for presets
• Auto Time Setting
• 30 Minute Back-Up in case of
Power failure
• 6 Rotary Head (4 Video Head and
2 Hi-Fi Audio Head)
• Long play
• Programme Delivery Control
System
• Timer Recording of up to 8
Programme per Month
• VIDEO Plus+® rapid timer
programming
• One-touch Timer Recording
(OTR)
• Video index Search System
• Slow Motion
• NTSC Video Cassette Tape
Playback on PAL TV
• Real-Time Tape Counter with
ZERO RETURN-Function
• Digital AUTO Tracking (ATR
Function)
• Repeat Playback
• On-Screen Display in 3
Language
• AV-Front input jack
• Audio Mixing
DVD Player
• Digital Audio Jack (Coaxial)
• Multi-Language
• Multi-Angle
• Surround audio
• Repeat Playback
• Memory/Random Playback
• Zoom
• Video Aspect Ratio
• Parental Control
• 3 Scene memory
• Digital (Optical or Coaxial) output
for Dolby Digital (AC-3) and DTS
• Playback of DVD, Video-CD and
Audio-CD
• PAL & NTSC DVDs playback
• A-B Repeat playback
• MP3 CD playback
Before using your unit
Disc playback operation
Safety Precautions ........................................... 2
Features ........................................................... 4
Contents ........................................................... 5
Parts and functions .......................................... 6
Display ............................................................. 7
Remote control ................................................. 8
Connections and Installation .......................... 10
Playback connection ...................................... 11
DISC ............................................................... 36
Setting setup language .................................. 37
Playback procedure ....................................... 38
Special playback ............................................ 39
DVD Picture Signal Selection/Zooming .......... 40
Repeat playback ............................................ 41
Memory playback/Random playback ............. 42
MP3 Playback ................................................ 43
Changing soundtrack language /
Changing Subtitles language ......................... 44
Changing angles / Title selection /
DVD menu ...................................................... 45
Setting up the VCR section
Tuning the TV Stations and Setting the Time
and Date Automatically .................................. 13
On-screen Language Selection ...................... 14
Setting the Time and Date Manually .............. 15
Tuning the TV Stations Manually ................... 16
Setting the VIDEO Plus+ Channel Number
(Guide CH) ..................................................... 17
Advanced function of DVD section
Parental control .............................................. 46
Setting menu language .................................. 48
Setting audio soundtrack language ................ 49
Setting subtitle language ................................ 50
Setting the aspect ratio of TV screen /
Setting on Screen display .............................. 51
Setting Audio .................................................. 52
Setting Operation ........................................... 53
Selecting the sound enhancement (E.A.M.)/
Setting Background/Setting Screen Saver ..... 54
Setting initial setup/output sound
conversion table ............................................. 55
Status display of Disc ..................................... 56
Table of languages ......................................... 57
Tape playback operation
Loading and Unloading a Cassette Tape ....... 18
Cassette tape playback .................................. 19
Special playback/Playback sharpness/Skip Search ........ 20
Repeat Playback ............................................ 21
Counter Display .............................................. 22
Video Index Search System ........................... 23
Recording
Recording a TV Programme ........................... 24
One-touch Timer Recording (OTR) ................ 26
VIDEO Plus+® Recording ............................... 27
Timer Recording Manually ............................. 29
Additional information
Problems and troubleshooting ....................... 58
Video head cleaning ....................................... 59
Specifications ................................................. 60
Advanced function of VCR section
NICAM Stereo Recording and Playback ........ 32
Audio Mixing ................................................... 34
Duplicating a Video Tape ............................... 35
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation or other rights owners and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation or other rights
owners. Reverse engineering or disassembly is prohibited.
PAL
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording
is not possible with this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
• VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The VIDEO
Plus+ system is manufactured under license from Gemstar Development Corporation.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Certain audio features of this product manufactured under license from Desper Products,Inc. Spatializer and the
circle - in - square device are trademarks owned by Desper Products,Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe
the rights of copyright owners and be contrary to copyright laws.
4
5
Parts and functions
Display
Display window
Front
1
OPEN/CLOSE button
INPUT SELECT button
2
3
Cassette Loading Slot
VCR/DVD mode selector button
VCR
VCR indicator
EJECT button
8
SLP
7
No.
REC button
Display window
Remote sensor
CHANNEL buttons
AUDIO (L/R)/
VIDEO IN jacks
DVD indicator
STOP button
PLAY button
6
AC power cord
Description
VCR mode of TV/VCR switch
Clock display (colon[ : ] flashes)
01H 00M 00S Counter display by hour/minute/second
5
Rear
5
6
Play indicator (DVD)
10 : 00
REW (Rewind) button
S
Video tape is in the unit
VCR
4
FWD (Fast Forward) button
M
Play indicator (VCR)
2
3
CH
Display
1
ON/STANDBY
button
4
Disc tray
tr 2
Track number display for CD
2 CH
TV channel position display
L1/L2/L3
External input display
SP
Tape speed indicator (VCR)
7
Timer recording display
8
Normal recording display (flashes during Recording PAUSE mode)
Note:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
RF IN jack
RF OUT jack
DVD OPTICAL
DIGITAL AUDIO
OUT jack
DVD COAXIAL DIGITAL
AUDIO OUT jack
DVD AUDIO (L/R) OUT jacks
DVD S-VIDEO OUT jack
6
SCART-socket
(for VCR/DECODER)
SCART-socket
(for TV-RGB/Composite)
7
Remote control
VCR
Remote control
Page
VCR
Switch to operate VCR
14
DVD
Switch to operate DVD
37
On/Standby
14
0-9
Direct channel selection of TV
24,26
Input setting
16~17,24,26,42,43
Enter a password
46
OPEN/CLOSE
Open or Close the tray
38
CLOCK COUNTER Change the clock and tape counter
22
ANGLE
Change playback angle of a DVD disc
45
COUNTER RESET Reset the counter to 00:00
22
TV/VCR
Switches between TV and VCR
25
AUX
Scart input or AV-Front input
35
AUDIO
Change sound track language of DVD
44
AUDIO SELECT Switches sound
33
SUBTITLE
Set Subtitle of a DVD disc
44
ATR
Digital AUTO TRACKING
20
MEMORY
Index for DVD
42
ZOOM
Zoom (for DVD playback)
40
E.A.M
Switch a preferred audio enhancement
54
PLAY MODE
Select playback mode
41,42
SP/LP
Sets the tape speed for recording
24,26,35
TIMER REC
Set the unit to start recording at a preset time. 28,30
REC/OTR
Recording
24,26,35
RETURN
Remove DVD set up menu
46
DISPLAY CALL
Display VCR or DVD operation status
24~25,56
PLAY
Playback
19,38,43
REW
Rewind/Review playback
19,20,39
FWD
Fast Forward/Forward search playback 19,20,39
STOP
Stop
19,38,43
SLOW
Slow motion playback
20,39
PAUSE/STILL
Still picture/Recording pause on/off 20,24,35,39
/
Skip chapter to forward or reverse direction
39
SKIP
INDEX
/
Search for the INDEX mark of a tape
23
TITLE
Select title of a DVD disc
45
A-B RPT
Repeat playback between A and B (DVD/CD) 41
SET UP VCR MENU Display menu of setup
14~17,20~21,46~55
CH +/–
Select channel of the connected TV or VCR
15,24,26,35
▲/▼
Cursor buttons
MENU
Display menu of DVD software
45
ZERO RETURN Stop the tape when the counter reaches 00:00:00 22
SET –/+
Setting buttons
28~30
Manual tracking buttons in playback mode
20
/
Cursor buttons - To move Up in the VCR menu
you press the . To move Down in the VCR
menu you press the .
ENTER
Enter information in the menu/Select option in the menu
INSTANT SKIP
Skip the unwanted short material of a tape
20
CANCEL
Delete Timer program
31
Cancel input data in the setting mode 27,31,42~46
VIDEO Plus+
VIDEO Plus Recording
27
Confirmation of Timer Recording
31
DVD
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT
ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
PLAY
REW
FWD
SLOW
PAUSE/STILL
STOP
INDEX – SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET –
ENTER
CANCEL
CH –
VIDEO Plus+
How to install the batteries
Use micro batteries type AAA.
the battery compartment
1 Slide
cover in the direction of the
two "AAA" batteries (supplied),
Replace the compartment
2 Install
3 cover.
paying attention to the polarity
arrow.
diagram in the battery
compartment.
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
Distance of Remote
Control Operation
Effective angle:
approx. 60°
approx.
5m
Point the remote
control directly at the
remote sensor.
8
9
Connections and Installation
Playback connection
Connect your DVD/VCR to your home's aerial and to your TV-set as shown in the illustration.
When you have finished these connections you connect your DVD/VCR to the 230-240 V / 50 Hz mains.
Aerial
TV
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is
dependent on the model and features of each component. Check the Owner's Manual provided with each
component for the location of SCART socket.
Connection to a Satellite Receiver
If a Satellite Receiver is used, we recommend the following configuration:
SCART-cable (not supplied)
TV Scart Socket (A1)
Aerial-Input
VCR/DECODER
Scart Socket (A2)
To Scart socket
RF-Input (from
house antenna)
Satellite
Aerial
TV
DVD/VCR
DVD/VCR
RF-Output (to TV)
Satellite
Receiver
SCART-cable (not supplied)
AC power cord 230V/50 Hz
Scart cable (not supplied)
To record from Satellite Receiver press "AUX" on the remote control of DVD/VCR twice. "A2" will appear on the
front display. Select the desired TV-program at Satellite Receiver.
Supplied Coaxial cable
Connect to a TV with S-Video Output
TV
Connect a TV with the Scart socket
In addition to the coaxial cable connection, connect also with scart cable. The picture and sound will be transmitted
best through the scart cable. In this case, the TV need not be tuned to the video recorder. The Video channel also
need not be tuned. The video recorder switch the television to video operation through the scart cable automatically.
The stereo-playback is possible in only case through a scart cable!
If your TV-set does not switch to video-playback operation automatically, please
turn your TV's video switch to VIDEO position manually.
S-Video Cord (not supplied)
DVD/VCR
Audio (L) Output
Audio (R) Output
To S-Video Input
S-Video Output
To Audio (R) Input
To Audio (L) Input
AUDIO Cord (not supplied)
Notes:
• The S-VIDEO jack is useful only for DVD section.
• If you use the connection with S-Video Cord, set the “Video Out Select” (P.40) to “Video”.
10
11
Tuning the TV Stations and Setting the Time and
Date Automatically
Playback connection
Connect to a Stereo Amplifier with Audio Output
If your DVD/VCR is connected to a stereo amplifier, the video soundtrack can output through the loudspeakers of
the stereo system.
Plug your DVD/VCR into the mains supply and it will start to automatically tune
itself in and set the correct date and
time. After setting itself up, you must
set the TV to the video channel.
SCART-cable (not supplied)
your DVD/VCR's plug into the mains supply. "Auto"
1 Plug
will start to flash in the display. Your DVD/VCR will auto-
To SCART
input
SCART-Socket
(for TV-RGB/Composite)
DVD/VCR
Preparation
• Make sure that your DVD/VCR is connected properly to the TV.
• If a satellite receiver is connected with the coaxial lead, make
sure it’s switched ON and set to SKY ONE.
• Turn on the TV and select the channel you wish to allocate for
video use.
matically tune itself in and set the correct
time and date (This may take
VCR
SP
approx. 4 minutes).
Stereo Amplifier
Audio (L) Output
Audio (R) Output
2
TV
To Audio (L) Input
To Audio (R) Input
AUDIO Cord (not supplied)
used a 21PIN scart lead you now, simply se3 Iflectyouthehave
AV channel on your TV and go to step 5. Tune the
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
SCART-cable (not supplied)
DVD/VCR
To SCART
input
SCART-Socket
(for TV-RGB/Composite)
TV
Coaxial digital
Audio Output
Coaxial digital cable
(not supplied)
Press and hold the
button on the front of your DVD/
VCR in the Standby mode until "rF"
VCR
and RF output channel "36" will
SP
appear in the display.
AV Amplifier with
built-in various
decoder as above
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The OPTICAL, COAXIAL jacks are useful only for DVD section.
VHS signal is output only from the SCART-sockets, AUDIO L/R jacks and RF OUT jack.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• DTS audio will be output only from the COAXIAL output. To hear DTS audio, DTS-Decoder is necessary.
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
Notes:
• The DVD/VCR automatically corrects
the clock setting every hour and
automatically adjusts the clock setting
for Daylight Saving Time.
• Your DVD/VCR will tune the TV
stations as follows.
CH 1
BBC 1
CH 2
BBC 2
CH 3
ITV
CH 4
Channel 4
CH 5
Channel 5
CH 6
Satellite
CH 7
etc.
For VIDEO Plus+ recording to work
correctly, this order should not be
changed.
• If you want to change the RF output
channel or switch to "OFF", press and
hold the DVD/VCR
on the front of
your DVD/VCR in the Standby mode
until the current RF output channel
appears. Press CHANNEL on your
DVD/VCR to select the RF channel you
desire.
• Skipped channels still may be selected
directly through the 1 to 0 keys.
• To cancel skipping select the skipped
channel using the 1 to 0 keys, then
press CANCEL. The channel No. does
not blink any longer, and the channel
No. now may be selected again using
CHANNEL.
TV in the same way as tuning in a TV broadcast station
until the word "TEST" flashes on the TV screen. Refer to
the TV operating instructions for tuning.
Now the output from the DVD/VCR is
tuned to this channel. Whenever you
want to play back a tape, select this
channel.
4
TEST
If there is interference in the picture (wavy lines, picture
roll, etc.), press CHANNEL on your DVD/VCR to select
any RF channel between 23 and 69, retuning your TV until
the word "TEST" flashes on the TV screen.
If you connected a satellite receiver as explained on page
11, you must switch off the DVD/VCR’s transmitter. Press
the VCR’s CHANNEL repeatedly until OFF appears in the
display window (OFF will appear
VCR
after 69 or before 23).
SP
5
Press the
button to turn OFF the DVD/VCR.
Now the TV is tuned to your DVD/VCR.
To skip a channel position
Unwanted channels can be
skipped so that they cannot
be called up by pressing
CHANNEL. Select the
channel to be skipped,
CH 29
VCR
SP
CH
...e.g. channel 29. Select channel 29, then press
CANCEL.
This channel’s number will be flashing. That way you can
cancel further channels one after the other.
12
13
On-screen Language Selection
Turn on your TV and select the VCR
channel which you have already tuned
on your TV. The TV will switch to AV
(VCR mode) automatically by the Scart
lead connection. The on-screen menu
can display any of three languages;
English, German and French.
Press VCR MENU. Press ▲ or ▼ to select the SYSTEM
1 SETUP.
Then press ENTER.
VCR
Setting the Time and Date Manually
Preparation
button to turn on the DVD/VCR.
• Press the
• Press VCR to select the VCR mode. (The VCR indicator will
light)
Preparation
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
Example: Setting the clock to 11:30, 26 Oct. 2002.
VCR
Press VCR MENU. Press ▲ or ▼ to select the SYSTEM
1 SETUP.
Then press
DVD
TIMER REC SET
OPEN/CLOSE
AUTO REPEAT
DVD
You must set the date and time manually
for timer recordings if Automatic tuning
process did not set them correctly.
OFF
VCR SETUP
CLOCK
COUNTER
CHANNEL SETUP
TIMER REC SET
ENTER.
The step-2 will appear
when clock is not set.
AUTO REPEAT
OFF
VCR SETUP
CHANNEL SETUP
SYSTEM SETUP
SYSTEM SETUP
OPEN/CLOSE
ANGLE
COUNTER RESET
SELECT :
SELECT :
CLOCK
COUNTER
ENTER
: ENTER
EXIT
: MENU
AUDIO
SUBTITLE
AUDIO SELECT
ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
ENTER
: ENTER
EXIT
: MENU
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT
ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
Press ▲ or ▼ to select
2 the
LANGUAGE. Then
press ENTER.
SYSTEM SETUP
Press ▲ or ▼ to select
2 the
CLOCK SET. Then
SYSTEM SETUP
press ENTER.
CLOCK SET
CLOCK SET
LANGUAGE/SPRACHE/LANGUE
LANGUAGE/SPRACHE/LANGUE
PLAY
SELECT :
SELECT :
PLAY
ENTER
: ENTER
EXIT
: MENU
REW
FWD
SLOW
REW
FWD
SLOW
PAUSE/STILL
STOP
Press ▲ or ▼ to select
3 the
desired language.
STOP
LANGUAGE/SPRACHE/LANGUE
Then press ENTER.
INDEX – SKIP INDEX +
FRANCAIS
TITLE
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
Press
or
repeatedly
3 until
26 appears. Then
press ▼ to continue.
ENGLISH
DEUTSCH
INDEX – SKIP INDEX +
PAUSE/STILL
A-B RPT
SET UP
VCR MENU
CH +
SET –
CH +
SET –
MENU
ZERO RETURN
SET +
INSTANT SKIP
SELECT :
OK : ENTER
CANCEL
CH –
CH –
VIDEO Plus+
14
CLOCK SET
DAY
MONTH
YEAR
TIME
AUTO TIME
26 WED
1
2000
0: 00
ON
EXIT : MENU
year, hour and minute in the same way
4 asSetinthestepmonth,
3. Then press ENTER.
Press VCR MENU repeatedly until the TV picture
4 appears
on the screen.
• In case of an error,
press ▲ to go back to
one step and enter
again.
Notes:
• If the unit does not operate properly,
or No key operation (by the unit and /
or the remote control): Static electricity, etc., may affect the player’s operation. Disconnect the AC power cord once,
then connect it again.
• If you use the unit for the first time and
press VCR MENU, instead of the MENU
screen in steps 1 and 2, the one in step 3
may appear. This is normal for this DVD/
VCR and is no indication of a malfunction.
Please first select the language to operate this unit.
: MENU
VIDEO Plus+
ENTER
CANCEL
: ENTER
EXIT
SELECT :
SET
:
OK
: ENTER
ENTER
SET UP
VCR MENU
ENTER
CLOCK SET
DAY
MONTH
YEAR
TIME
AUTO TIME
SELECT :
SET
:
OK
: ENTER
Notes:
• The AUTO TIME function adjusts the
clock only if the error is within 5
minutes.
• The VCR automatically adjusts the
clock setting for Daylight Saving Time
once you set AUTO TIME to ON.
26 SAT
10
2002
11: 30
ON
EXIT : MENU
Press or
to select AUTO TIME ON or OFF.
5 The
VCR automatically corrects the clock setting every
hour once you set AUTO TIME to ON.
Press VCR MENU repeatedly until the TV picture
6 appears
on the screen.
7 The clock will begin operation.
VCR
SP
CH
15
15
Setting the VIDEO Plus +® Channel Number (Guide CH)
Tuning the TV Stations Manually
This VCR has one built-in tuner to
receive broadcasts. Before you
record a TV broadcast, you must set and
preset all channels. This VCR can preset
up to 80 channels.
Preparation
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
Example: Preset the BBC 2 on programme position 2.
VCR
VCR MENU.
1 Press
Press ▲ or ▼ to select the
DVD
AUTO REPEAT
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
REC/OTR
RETURN
DISPLAY
CALL
ENTER
: ENTER
EXIT
: MENU
Press ▲ or ▼ to select the
2 CH
TUNING.
ANGLE
COUNTER RESET
CHANNEL SETUP
CH TUNING
Press ENTER to select CH
TUNING screen.
GUIDE CH SET
TV/VCR
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
"
automatically ("
changes to " "). Press
or
repeatedly until
BBC 2 appears. Only in
case of receiving a weak
broadcast (drifting
picture), does search fail
to stop. If you want to
stop, press or .
Press ENTER to preset.
The search menu screen
will disappear if the next
mode is not activated in
less than 50 seconds.
PAUSE/STILL
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CH Ð
CANCEL
VIDEO Plus+
CH 01
BBC 1
CH 02
BBC 2
CH 03
ITV
CH 04
CH4
CH 05
CH5
CH 06
SATELLITE
AUDIO
SUBTITLE
AUDIO SELECT
ATR
AUX
ZOOM
MEMORY
SELECT :
ENTER
: ENTER
EXIT
ENTER
: ENTER
EXIT
: MENU
TIMER REC
: MENU
E.A.M
REC/OTR
DISPLAY
CALL
RETURN
"SAT" with ▲ or ▼ or
3 Enter
number keys.
PLAY
SLOW
SEARCH :
EXIT
: MENU
: MENU
GUIDE CH SET
GUIDE
INDEX – SKIP INDEX +
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET –
ENTER
CH –
CANCEL
CH
CH
:
OK
: ENTER
VIDEO Plus+
1
VCR
CH
8
6
PAUSE/STILL
SET UP
VCR MENU
"6" with ▲ or ▼ or
4 Enter
number keys.
:
/ 0-9
OK
: ENTER
EXIT
: MENU
GUIDE CH SET
GUIDE
Then press ENTER.
If you have connected your
satellite using the scart
socket, you must select "AV"
for the VCR CH number.
VCR
CH
CH
6
6
SET
:
/ 0-9
OK
: ENTER
CLEAR
: CANCEL
EXIT
: MENU
/ 0Ð9
5 For other Codes, repeat steps 3 and 4.
VCR MENU repeatedly until the TV picture
6 Press
pears.
EXIT : MENU
TV
CH 2
5
Press VCR MENU repeatedly until the TV picture
6 appears
on the screen.
ap-
GUIDE CH
STATION
BBC1
1
BBC2
2
ITV
3
CH4
4
CH5
5
Satellite
6
17
Loading and Unloading a Cassette Tape
Cassette tape playback
Preparation:
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
.
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording
is not possible with this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS
recordings with regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
• SQPB playback can be seen only at PAL SP mode.
a prerecorded tape
1 Load
(When loading a cassette tape
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
Push the centre of the tape until it is automatically
inserted.
: ENTER
EXIT
SET
STOP
Repeat the steps 3 and 4 to preset other TV stations.
Loading
ENTER
CH
CH 1
SEARCH :
OK
: ENTER EXIT : MENU
and
GUIDE CH SET
Then press ENTER.
enter 0 2 with the 1 to 0
numbered keys). Then
press ENTER.
Use only video cassette tapes marked
CH TUNING
FWD
GUIDE CHANNEL TABLE
16
CHANNEL SETUP
PLAY MODE
SP/LP
REW
Press ▲ or ▼ repeatedly
4 until
2 is displayed. (Or
Note:
Occasionally, the auto search might catch
a weak signal and stop. If the TV station
signal is weak, you shouldn't store this
station.
In that case restart the auto search
or .
using
2
Press ▲ or ▼ to select the
GUIDE CH SET. Then press
ENTER.
SELECT :
Press
(falling frequency) or
(rising frequency)
3 once
to start the search. It stops at each broadcast
FWD
STOP
OFF
VCR SETUP
CLOCK
COUNTER
PLAY
SLOW
AUTO REPEAT
SYSTEM SETUP
DVD
OPEN/CLOSE
SELECT :
REW
TIMER REC SET
CHANNEL SETUP
VCR
SELECT :
AUDIO
SUBTITLE
AUDIO SELECT ATR
TIMER REC
SETUP. Then press ENTER.
SYSTEM SETUP
ANGLE
COUNTER RESET
AUX
OFF
VCR SETUP
CHANNEL SETUP
CLOCK
COUNTER
TV/VCR
Preparation
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
Example: Satellite channel has been incorrectly stored on
channel 8 of your VCR.
VCR MENU. Press ▲
1 Press
or ▼ to select the CHANNEL
TIMER REC SET
CHANNEL SETUP. Then
press ENTER.
OPEN/CLOSE
The TV stations must be stored according
to the tuning guide given on page 13,
otherwise the VIDEO Plus+ feature will not
work. If for any reason you did not select
channels BBC1, BBC2, ITV, CH4, CH5 and
Satellite in channel positions 1 through to 6
respectively, you must set each VIDEO Plus+
channel number (GUIDE CH) manually.
Insert the cassette tape with its labeled side facing up
and the erase prevention tab positioned at your left.
An inverted cassette tape cannot be inserted.
ANGLE
COUNTER RESET
TV/VCR
AUDIO
SUBTITLE
AUDIO SELECT
ATR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
without the erase prevention
tab, playback will start automatically).
start playback
2 To
Press PLAY.
Playback will start.
If the cassette has not loaded
yet,
will blink for 4 seconds.
VCR
SP
H
M
S
VCR
SP
H
M
To stop playback
S
Erase prevention tab
Press STOP.
Automatic power ON
When you insert a cassette tape the DVD/VCR power will turn ON automatically.
PLAY
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
REW
FWD
VCR
SP
SLOW
H
M
S
PAUSE/STILL
STOP
Unloading
1
To rewind the tape or forward it rapidly
Press EJECT on the unit. Even if a tape is being
played, press this button only once.
2
Remove the cassette tape.
INDEX – SKIP INDEX +
SET UP
VCR MENU
CH +
SET –
Stop the playback or recording with STOP.
TITLE
A-B RPT
MENU
ZERO RETURN
To rewind the tape:
To forward the tape:
SET +
INSTANT SKIP
Press REW.
Press FWD.
ENTER
CANCEL
VIDEO Plus+
VCR
VCR
SP
CH –
H
M
SP
S
CH
To stop the tape-winding, press STOP. To switch to playback
directly (without 3), press PLAY.
Automatic tape eject
This VCR will automatically rewind the tape when the tape has ended. And when the tape is rewinded to its
beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure
Remove the erase prevention tab with a screwdriver.
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab
18
Forward/Reverse picture search mode
To record again
Adhesive tape
• This VCR selects the playback tape
speed SP or LP automatically.
• The Cassette tape and DVD disc can
be played back simultaneously. If you
press VCR or DVD, the tape playback
and DVD playback alternate with each
other on the screen.
When the tape is being winded, you can switch to picture search
mode (see next page). To do this, press REW or FWD and hold
it down. The unit will resume the tape winding as soon as the
button is released.
NTSC video cassette playback
When using a pre-recorded NTSC video cassette tape, the
connected TV set must operate with a 60 Hz vertical frequency.
Otherwise the on-screen picture will be affected by vertical
rolling. Even if your VCR set is capable of processing NTSC video
signals, the picture may be shortened vertically (appearance of
black bars at the top and at the bottom of the TV screen). The
dubbing of a NTSC video cassette tape to a standard PAL VCR
is not possible.
19
Special playback/Playback sharpness/Skip Search
Repeat Playback
Special playback
Playback sharpness
Picture Search
Adjust the sharpness of playback picture during
playback. During slow motion, still picture and picture
search, sharpness-adjusting is impossible.
Reverse picture search function
Press REW x 1 or x 2 during the playback.
Forward picture search function
Press FWD x 1 or x 2 during the playback.
To return to playback: Press PLAY.
1 Start the playback of video tape.
VCR MENU.
2 Press
Press
or
to select
VCR
TIMER REC SET
AUTO REPEAT
Still Picture
VCR SETUP. Then press
ENTER.
Press PAUSE/STILL during playback. To resume
normal playback: Press PLAY.
If the Repeat function is switched
on, the playback will continue until
it reaches the tape-end and then
rewind to the beginning of the tape.
This process will repeat until the
unit is turned off.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion,
press the SET + or – to reduce the noise bars.
If the still picture jitters excessively, press SET + or –
to stabilize the still picture.
Frame by Frame picture
Press
or
to select
PLAYBACK SHARPNESS. Then press
ENTER.
OPEN/CLOSE
CHANNEL SETUP
CLOCK
COUNTER
: ENTER
: MENU
ANGLE
COUNTER RESET
TV/VCR
AUX
AUDIO
SUBTITLE
AUDIO SELECT ATR
or
2 Press
[ON] or [OFF].
/
ENTER
: ENTER
EXIT
: MENU
to select
TIMER REC SET
AUTO REPEAT
ON
VCR SETUP
VCR SETUP
NICAM
[AUTO]
AUDIO MIX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
CHANNEL SETUP
SYSTEM SETUP
[OFF]
PLAYBACK SHARPNESS
SELECT :
/
SELECT :
ENTER
: ENTER
ENTER
: ENTER
EXIT
: MENU
EXIT
: MENU
Press
or
to adjust
the playback sharpness
to the level you reguire.
REW
FWD
VCR MENU repeatedly until the TV picture appears.
3 Press
If "ON" has been selected, the tape will be repeatedly
played.
PLAYBACK SHARPNESS
+ÐÐ+ÐÐ+ÐÐ+ÐÐ
SLOW
2
SET
:
EXIT : MENU
CENTRE : CANCEL
Adjusting tracking condition
softer
sharper
VCR MENU repeatedly until the TV picture
5 Press
appears on the screen.
Manual tracking adjustment
If automatic tracking cannot eliminate noises well during
playback, press SET + or SET – to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine
adjustment, or press and hold for a coarse adjustment.
Note:
To return to the initial sharpness setting, press CANCEL
while the sharpness setting screen is appearing.
To return to automatic tracking, press A. TRK.
Each time you press INSTANT SKIP while a tape is playing,
the unit will fast-forward ahead 30 seconds on the tape. You
may press the button up to six times in a row to move 180
seconds (three minutes) ahead.
Notes:
• The audio output is muted during SPEED SEARCH,
STILL, FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars
which are caused by the system.
• The Special Playback will automatically change to
playback after approx. 5 minutes to protect the video
tape against excessive wear.
OFF
VCR SETUP
SELECT :
SYSTEM SETUP
EXIT
AUTO REPEAT
SYSTEM SETUP
VCR SETUP
ENTER
TIMER REC SET
CHANNEL SETUP
PLAY
4
During playback, press PAUSE/STILL one by one:
The picture advances frame by frame.
To return to playback: Press PLAY.
Automatic tracking adjustment
Whenever you insert a tape and start playback,
automatic tracking starts working and continuously
analyzes the signal to enable optimum picture quality
during playback.
VCR MENU.
1 Press
Press ▲ or ▼
[OFF]
Slow Motion
3
Preparation
• Turn on the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode.
to select the AUTO
REPEAT.
DVD
SELECT :
During playback press SLOW.
You can change the slow speed by the additional
pressing of SLOW.
To return to playback: Press PLAY.
To set the Repeat function
PAUSE/STILL
STOP
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
ENTER
CH Ð
CANCEL
VIDEO Plus+
Skip Search
For example: 1 press: Approx. 30 seconds of tape
2 presses: Approx. 60 seconds of tape
3 presses: Approx. 90 seconds of tape
Note:
To cancel the auto repeat mode, follow the
above steps 1 and 2, then select "OFF"
and confirm by pressing VCR MENU.
20
21
Counter Display
ZERO RETURN function
This function makes tape-rewinding
stop at the counter 00:00:00 position
automatically.
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
Video Index Search System
Preparation:
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
DISPLAY.
1 Press
The counter display shows the
tape running time during
playback or recording.
The Recorder will indicate REC
during recording for itself.
00:04:38 SP
VCR
SP
H
M
The counter display will be reset
to the "00:00:00" position (e.g.
the beginning of recording).
REW
FWD
SLOW
PAUSE/STILL
STOP
CLOCK
COUNTER
CH 2
12:00 SUN
ANGLE
COUNTER RESET
00:00:00 SP
H
M
S
STOP when playback or recording is finished.
3 Press
Press ZERO RETURN.
SET UP
VCR MENU
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
The CLOCK COUNTER button
INSTANT SKIP
Press CLOCK COUNTER during the playback. The clock and tape
counter alternate with each other in the display.
SET +
ENTER
CANCEL
CH Ð
AUX
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
REW
FWD
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
H
M
S
the end of the TV commercial
is reached, then press STOP.
goes off, STOP may be pressed. This short recording
process will be sufficient to set an index mark.
This will result in about 10 seconds of the TV commercials to
be overwritten by another recording. Due to the system the
end of this recording will be followed by a recording gap (noise
signal) of approx. 5 seconds.
Recording several Index Marks
Due to the system only one index mark will be recorded at the
beginning of a recording. If you intend to set several index
marks during a single recording, follow the procedure below:
CH +
SET Ð
where an index mark is to be
set press PAUSE/STILL. The
unit will switch to the recording
pause mode.
PAUSE/STILL
STOP
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
VCR
SP
1 Start playback and wait until
1 At the point of the recording
PLAY
SLOW
VIDEO Plus+
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
MEMORY
The tape will be rewinded or fast forwarded and automatically
stop at the ”00:00:00” position.
4 Press DISPLAY once again to make the all indicator disappear.
INDEX Ð SKIP INDEX +
Example: Indexing of TV commercials.
2 Press REC/OTR. When the "INDEX" on-screen indication
DVD
OPEN/CLOSE
VCR
PLAY
VCR
S
COUNTER RESET at the
2 Press
desired tape position.
SP
CH 2
12:00 SUN
Whenever a recording is begun an
invisible index mark is recorded on the
tape.These index marks are all identical,
and each mark means: "Here starts a
new recording". Every DVD/VCR
equipped with the Video Index Search
System (VISS) can locate these marks
at the beginning of any recording.
2 Press CH repeatedly to switch
CH 2
back to the original TV
program. Press PAUSE/STILL
to resume recording.
ENTER
CANCEL
CH Ð
INDEX
VIDEO Plus+
VCR
SP
Notes:
• When you load a video cassette, the display indication changes to "00:00:00".
• The counter display does not function
on non-recorded (blank) sections of the
tape. When you rewind, fast forward or
play tapes through blank sections, the
counter display stops.
22
CH
Index Search
PM
Note:
You can set the tape counter to 00:00:00 with COUNTER RESET
anytime. Therefore, the counter display can also indicate 00:00:00,
even when the tape counter does not reach its beginning yet. Even if
the tape counter indicates 00:00:00, it can be rewinded moreover. If
the tape was rewinded over the point of 00:00:00, the minus mark (–
) appears in the counter display. Although the tape counter seems to
forward when you press REW, in fact the tape is being rewinded.
When the tape reaches the beginning, the tape-rewinding stops
automatically.
Notes:
• When you record an INDEX mark at
the very beginning of the tape, the
mark may not be found.
• During INDEX search, the tape may
stop and begin to play at a slightly
different location.
• INDEX may not function properly with
old or worn out video tapes.
• INDEX marks may not be found if it is
extremely close to the point where the
search began.
• In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape.
Press INDEX + or – during stop
or play mode.
For Succeeding programs:
Press INDEX +.
For Preceding programs:
Press INDEX –.
(Additional press increases the
INDEX NO. up to 9.)
When the INDEX + or – is
pressed, the unit starts
searching the INDEX NO.
selected and finds the portion,
then playback starts automatically.
To stop the Index Search, press
STOP.
+3
or
is displayed
INDEX NO. (up to 9)
23
Recording a TV Programme
Recording a TV Programme
Preparation:
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
VCR
DVD
OPEN/CLOSE
a blank cassette tape with the
1 Load
erase prevention tab intact. (The
DVD/VCR will automatically turn
on.)
CLOCK
COUNTER
ANGLE
COUNTER RESET
TV/VCR
AUX
AUDIO
SUBTITLE
AUDIO SELECT ATR
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
REW
FWD
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
CH Ð
SP
H
M
S
the VCR is recording press TV/VCR until the "VCR"
2 While
indicator on the display goes off. The TV set now displays
the program of its built-in receiving module. Select the TV
channel you want to watch on the TV set. Although the TV
set now shows another program the DVD/VCR will continue recording the previously selected programme.
DVD
SP
H
M
S
“VCR” indicator goes off.
4
On the VCR, press REC.
Or on the Remote, press REC/OTR.
" " will appear on the screen for
about 4 seconds and “ ” will
appear on the display.
ANGLE
COUNTER RESET
AUX
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
CH 29
H
M
TV/VCR you can switch the TV screen between the
3 Using
DVD/VCR picture and the TV picture. If the "VCR" indicator
is lit on the display, you will watch the DVD/VCR picture. This
has no trouble on the recording.
VCR
SP
H
M
S
“VCR” indicator goes on.
INDEX
SP
SUBTITLE
AUDIO
ATR
AUDIO SELECT
TV/VCR
MEMORY
PLAY
To Display VCR operation Status
S
If the erase prevention tab is removed, the tape will eject when
REC/OTR are pressed for recording. (see p.18)
REW
FWD
SLOW
PAUSE/STILL
STOP
VIDEO Plus+
VCR
“VCR” indicator goes on.
CLOCK
COUNTER
ENTER
CANCEL
1
Press TV/VCR until "VCR" appears on the display. Select
the program on the DVD/VCR you want to record. This
program can be watched on the screen and recorded by the
DVD/VCR.
OPEN/CLOSE
VCR
INDEX Ð SKIP INDEX +
VCR
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
PAUSE/STILL
STOP
SET UP
VCR MENU
You can record a programme using
the TV receiver of the DVD/VCR and at
the same time watch another programme on the TV set using its receiver. As the DVD/VCR automatically
switches the TV set the following
points should be observed:
a recording in Long Play mode is intended, press SP/LP to
3 Ifdisplay
"LP". (see Note below)
PLAY
SLOW
the program(e.g.29) you want to record with CH +/– or
2 Select
number keys.
Recording with a SCART Lead:
To Stop Recording
Press DISPLAY. The clock, day of the week and more
informations will be indicated.
To cancel the indicating: Press DISPLAY until all indicator
disappear.
Press STOP.
INDEX – SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
Day of the week
Time
SET –
ENTER
CH –
CANCEL
VIDEO Plus+
To Stop Recording Temporarily
To stop a recording for a short
period of time press PAUSE/STILL.
Press this button again if you want
to resume the recording.
Notes:
• Since the DVD/VCR has a built-in TV
tuner the TV set may be turned off when
recording. The TV set may only be used
to check for accurate program adjustments or to monitor recordings.
• You can confirm on the TV-screen
whether you selected SP or LP. Press
DISPLAY to see the status display. (see
page 25)
• If you wish to watch the DVD playback
during the normal recording on VCR,
press DVD to change to DVD mode and
perform the DVD playback (see page
38).
Indication for
Hi-Fi-playback
or stereoreception
23:59 MON
HI-FI
Audio Select
STEREO
Deck-status
here: Playback
Programme
number or
Scart input
CH 80
LINE1/LINE2/
LINE3
01:36:58 SP
Cassette in
Unit
Tape speed
Stand of Tape counter
Attention:
A safety circuit turns the pause mode off automatically after 5
minutes, and the DVD/VCR will stop the recording mode.
Auto Rewind Feature
The DVD/VCR will automatically rewind
when the tape has ended (except during
OTR and TIMER REC). It will also eject
the cassette tape.
24
25
VIDEO Plus+® Recording
One-touch Timer Recording (OTR)
The one-touch timer recording feature
provides a simple and convenient way
to make a timed recording.
Preparation:
• Turn ON the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
a blank cassette tape with the
1 Load
erase prevention tab intact. (The
VCR
DVD
CLOCK
COUNTER
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
REC/OTR
RETURN
DISPLAY
CALL
REW
FWD
PAUSE/STILL
STOP
INDEX Ð SKIP INDEX +
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET Ð
SET +
INSTANT SKIP
Press REC on the VCR or REC/OTR on the Remote to begin
recording. Press REC on the VCR again to stop recording after
30 minutes. Each additional press of REC will increase recording
time as shown in the chart below, up to a
maximum of 5 hours. The OTR and recording time will appear
on the screen for about 4 seconds.
OTR 0:30
CH 29
H
M
CH Ð
AUX
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
Tape speed: SP
Recording
0:30
5:00
1:00
3:00
4:00
Tape speed: LP
Recording
0:30
10:00
REW
FWD
PAUSE/STILL
STOP
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
.......
1:00
5:00
1:30
SET Ð
4:00
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
2:00
1:30
CH +
CH Ð
VIDEO Plus+
2:00
Press REC/OTR repeatedly until the
desired time appears on the display.
26
To stop the OTR
Press STOP.
the PlusCode
2 Enter
Number using number
• In case of an error, press
CANCEL and enter the
desired number again.
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE NO. : 0Ð9
SELECT
:
CLEAR
: CANCEL
OK
: ENTER
: VIDEO PLUS+
EXIT
57378
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE NO. : 0Ð9
SELECT
:
CLEAR
: CANCEL
OK
: ENTER
EXIT
: VIDEO PLUS+
3 Press ▲ or ▼ to select ONCE, DAILY or WEEKLY.
ONCE = To record a
programme only once
DAILY = To record TV
programmes transmitted
daily
WEEKLY = To record TV
programmes transmitted
once a week.
3:00
To Extend the Recording Time
Notes:
• If you wish to watch the DVD playback
during the OTR, press DVD to change
to DVD mode and perform the DVD playback (see page 38).
• If the tape supply has not sufficed for
OTR recording, the clock symbol ( ) will
blink at the tape-end and then VCR
mode will change to DVD mode.
In this case, press TIMER REC to cancel
blink or press EJECT to remove
the
the cassette tape.
Note: If any button is not
pressed within 60 seconds,
the Recorder switches
back to TV operation.
keys.
PLAY
SLOW
1 Press VIDEO Plus+.
S
INDEX
VIDEO Plus+
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
MEMORY
VCR
ENTER
CANCEL
CLOCK
COUNTER
ANGLE
COUNTER RESET
If a recording in Long Play mode is intended, press SP/LP (TAPE
3 SPEED)
to display "LP". (see note on page 28)
SP
SET UP
VCR MENU
OPEN/CLOSE
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
4
PLAY
DVD
the program (e.g.29) you want to record with CH +/– or
2 Select
number keys.
AUDIO
SUBTITLE
AUDIO SELECT ATR
TIMER REC
SLOW
VCR
VIDEO Plus+ and PlusCode are
registered trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under license
from Gemstar Development Corporation.
Preparation
• Turn on the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
DVD/VCR will automatically turn
on.)
OPEN/CLOSE
ANGLE
COUNTER RESET
Look up the PlusCode Number in an
appropriate TV programme magazine.
Select the desired TV programme for
recording and refer to the PlusCode
Number next to it.
57378
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE NO. : 0Ð9
SELECT
:
CLEAR
: CANCEL
OK
: ENTER
EXIT
: VIDEO PLUS+
Press ENTER. By the PlusCode Number, the entered data
4 appears
on the screen.
OTR 1 : 30
CH 29
Select your tape speed.
Notes:
• The built-in timer stores 8 memories. If
the "PROGRAM FULL" indication
appears, you must delete one memory
(see page 31).
• When the power supply is interrupted
for more than 30 minutes, the preset
programme is cleared. In this case,
you have to set the timer again.
• If the entered Number
is not correct, the
indicator "PLUS CODE
NO. ERROR" will
appear.
Enter the correct number.
PLUSCODE NO.
DATE
15 FRI
START
17:30
END
18:00
CH
3
SPEED
SP
PDC
OFF
57378
SELECT :
SET
:
EXIT
: MENU
OK : ENTER
27
VIDEO Plus+ Recording
Timer Recording Manually
If you have selected Daily or Weekly in step 3, then you
can select a recording date again. The date must blink.
If it does not blink, then press ▲ or ▼ repeatedly until
the DATE blinks. Then press
or
repeatedly until
the desired date appears. The following date options are
available:
SUN-SAT: all dates from Sunday to Saturday, or
MON-SAT: only from Monday to Saturday, or
MON-FRI: only from Monday to Friday.
WKL-MON: each Monday, WKL-TUE: each Tuesday
WKL-SUN: each Sunday, etc.
The built-in timer allows unattended
recording of up to 8 programmes
within 1 month.
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
Preparation
• Turn on the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
• Load a video cassette with the erase prevention tab intact.
Make sure that the time and date are correct.
Example: Timer recording for the 23rd, Friday, on channel 3,
19:30 to 21:30 and LP mode.
1 Press VCR MENU.
ANGLE
COUNTER RESET
TV/VCR
Recording period extension
The recording end-time will be set by VIDEO Plus+
automatically. However you can extend the recording
end-time manually. The time END must blink.
If it does not blink, then press ▲ or ▼ repeatedly until
to extend.
the time end blinks. Then press
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
FWD
SLOW
5
6
:
:
:
:
:
:
:
OFF
VCR SETUP
SYSTEM SETUP
ENTER
: ENTER
EXIT
: MENU
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
PAUSE/STILL
STOP
:
/ ENTER
SELECT :
EXIT : MENU
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
SELECT : / ENTER
EXIT : MENU
AUTO REPEAT
Each line stands for one
programme of the 8
memories. Select one
line with ▲ or ▼ .
Then press ENTER.
15 FRI 17:30 18:00 3SP
:
:
:
:
:
:
:
TIMER REC SET
CHANNEL SETUP
SELECT :
2
PLAY
REW
Press ENTER after the
confirmation. Then press
VCR MENU repeatedly until
the TV picture appears. To
enter another programme,
repeat
steps 1 - 5.
Press ▲ or ▼ to select
the TIMER REC SET.
Then press ENTER.
SUBTITLE
AUDIO
AUDIO SELECT ATR
AUX
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
dates with
3 Setorthe desired
. Then press ▼
to accept them.
ENTER
CH Ð
CANCEL
• Daily/weekly settings
can be found by
pressing
or
repeatedly (see page
30).
VIDEO Plus+
Although the data is stored in the timer memory, the timer
function is not yet ready for recording. To accomplish this,
activate it by pressing TIMER REC.
If no cassette tape is loaded,
the clock symbol is blinking.
VCR
TIMER REC SET
DATE
23 FRI
11:30
START
:
END
1
CH
SP
SPEED
OFF
PDC
SELECT :
SET
:
EXIT
: MENU
the Starting time (19:30), ending time (21:30)
4 Set
channel (3) and tape speed (LP) in the same way as in
Notes:
step 3.
• As long as the timer is activated (clock
symbol indicated on the display), you
cannot use the VCR. If you want to use
the VCR, first press TIMER REC to
deactivate the timer.
• Not all TV Stations transmit PDC signal
all of the time, therefore it is advisable to
check before setting PDC to ON, if you
do set PDC to ON and no signal is
received your recording might not take
place at all. To check PDC status,
change to the channel on your DVD/VCR
you wish to record from, if the word
"PDC" appears on the screen for a few
seconds then that channel is
broadcasting PDC and you can set the
feature to ON.
To record with the PDC (Programme
Delivery Control) system
The PDC system starts
TIMER REC SET
recording when it picks up
DATE
15 FRI
START 17:30
a special signal transmitted
END
18:00
CH
3
by the broadcaster with the
SPEED LP
PDC
ON
TV programme – even if
SELECT :
:
SET
the TV programme starts
: MENU
EXIT
OK : ENTER
early, late or runs on longer
than scheduled. In step 4, press ▼ repeatedly until PDC
OFF flashes, then press
or
to display "ON" for
recording with PDC.
Notes:
• When the power supply is interrupted for
more than 30 minutes, the preset
programme is cleared. In this case, you
have to set the timer again.
• If you want to set the timer with the PDC
function, see "To record with the PDC
system" on page 28.
• In case of an error,
press ▲ to go back to
the previous step and
repeat.
TIMER REC SET
DATE
23 FRI
19:30
START
21:30
END
3
CH
LP
SPEED
OFF
PDC
SELECT :
SET
:
EXIT
: MENU OK : ENTER
28
29
Timer Recording Manually
Timer Recording Manually
ENTER to accept
5 Press
them. To enter other pro-
19:30
23 FRI
grammes, repeat steps 2 to
4, or press VCR MENU
repeatedly until the TV picture appears.
:
:
:
:
:
:
:
:
:
EXIT
Confirmation/Cancellation of the Timer Recording
3 LP
the Timer has been activated, now press TIMER REC to
1 Ifdeactivate
the timer. The clock symbol will disappear. Then
VCR
:
:
SELECT :
Notes:
• In case of a timer recording from the Scart
socket, proceed as follows: When "CH" is
or
blinking in picture/step 4, press
repeatedly until "LINE" appears.
• If the clock symbol blinks when the timer
recording is completed, the TV programme
has not been completely recorded
because of an insufficient tape supply.
• As long as the timer is activated (clock
symbol indicated on the display), you
cannot use the DVD/VCR. If you want to
use the DVD/VCR, press TIMER REC to
deactivate the timer.
21:30
:
:
press VCR to change to VCR mode.
DVD
:
OPEN/CLOSE
/ ENTER
: MENU
CLOCK
COUNTER
6
Although the data is stored in the timer, it is not ready for
recording. To start timer recording, press TIMER REC to
turn it on. When no video cassette is loaded, the clock symbol is blinking.
VCR
ANGLE
COUNTER RESET
TV/VCR
AUX
MEMORY
ZOOM
TIMER REC
REC/OTR
All the timer programmes
will appear.
28 FRI
19:30
21:00
3 LP
30 SUN
12:15
13:00
1 SP
30 SUN
19:00
22:00
3 LP
:
:
:
:
:
:
AUDIO
SUBTITLE
AUDIO SELECT ATR
E.A.M
PLAY MODE
SP/LP
RETURN
DISPLAY
CALL
:
PLAY
REW
FWD
SLOW
PAUSE/STILL
STOP
Press ▲ or ▼ to select
the timer programme you
wish to cancel.
Then press CANCEL.
This line is now cancelled.
▼
:
/ ENTER
: CANCEL EXIT : MENU
28 FRI
19:30
21:00
3 LP
30 SUN
12:15
13:00
1 SP
:
:
:
:
:
:
:
:
:
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
:
:
SELECT :
EXIT
Follow the procedure for timer recording on the previous
page. In picture/step 3 (when date and day is blinking),
press
repeatedly until the desired setting appears
(weekly or daily).
:
:
SELECT :
CLEAR
3 To cancel a Timer programme.
When you turn the unit off, the timer will be switched on
automatically. The clock symbol will appear on the display.
If you still want to use the recorder, press TIMER REC
first. Then the clock symbol will disappear from the display.
Weekly (e.g. WKL-TUE: each Tuesday) or daily (e.g.
MON-SAT Monday to Saturday) Timer recording
To confirm a Timer programme.
2 Press
VIDEO Plus+ twice.
:
/ ENTER
: MENU
VCR MENU (or VIDEO Plus+) button repeatedly
4 Press
until the TV picture appears.
ENTER
CANCEL
DATE-DAY
SUN-SAT
WKL-FRI
MON-SAT
WKL-SAT
MON-FRI
WKL-SUN
WKL-THU
WKL-WED
CH Ð
VIDEO Plus+
WKL-MON
WKL-TUE
Set other START, END, CH, SPEED as previous pages.
In case of overlapping Timer programmes
• Do not overlap timer programmes as portions of the
conflicting programmes will be lost. The first recording
time has priority over the next recording time as
shown in the diagram below.
8 : 00
Notes:
• The daily/weekly recording can be
made continuously until the recording is
cancelled or the tape reaches the end.
• During timer recording, the automatic
rewinding mechanism does not function.
30
9 : 00
10 : 00
11 : 00
Program 1
Program 2
Deleted Parts
Program 3
Non Recorded Portion Parts
Recording
Control Settings
Prog.1
Prog.2
Prog.3
31
NICAM Stereo Recording and Playback
NICAM Stereo Recording and Playback
This DVD/VCR is capable of recording
sound in Hi-Fi system. The recording
will be performed automatically.
NICAM STEREO broadcasts are
recorded in its original sound system
regardless of the setting. If you wish
to record NICAM programmes, select
NICAM "AUTO" as follows.
Preparation:
• Turn ON the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
Playback
Use AUDIO to select under stereo/mono or bilingual playback.
See the table below for more information.
NICAM stereo sound reception:
On-screen indications Stereo playback
(for 4 sec.)
performed in:
VCR MENU. Press ▲
1 Press
or ▼ to select VCR SETUP.
VCR
TIMER REC SET
AUTO REPEAT
DVD
[OFF]
VCR SETUP
Then press ENTER.
ENTER
: ENTER
EXIT
: MENU
ANGLE
COUNTER RESET
OPEN/CLOSE
CLOCK
COUNTER
2
ANGLE
COUNTER RESET
TV/VCR
AUX
TV/VCR
Press ▲ or ▼ to select NICAM.
/ or ENTER to
Then press
select [AUTO].
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
AUDIO
SUBTITLE
AUDIO SELECT
ATR
AUX
VCR SETUP
[AUTO]
AUDIO MIX
SELECT :
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
/
ENTER
: ENTER
EXIT
: MENU
FWD
SLOW
PAUSE/STILL
STOP
Mono
One's mother
tongue dubbing
(Main sound)
PLAY
the VCR MENU repeatedly until the TV picture
3 Press
appears.
NICAM STEREO broadcast
"NICAM ST" illuminates when a
NICAM STEREO broadcast signal is
received.
Original sound
track (Sub sound)
R CH
NICAM programmes are divided into 4 types as
shown below.
PLAY
Right channel
signal output from
both loudspeakers
[OFF]
REW
REW
One's mother
tongue dubbing
(Main sound)
L CH
NICAM
PLAYBACK SHARPNESS
AUDIO
SUBTITLE
AUDIO SELECT ATR
Left channel signal
output from both
loudspeakers
STEREO
CLOCK
COUNTER
SELECT :
DVD
Simultaneously
both languages
from HiFi track
(Mixed sounds)
OPEN/CLOSE
CHANNEL SETUP
SYSTEM SETUP
VCR
Bilingual playback
performed as follows:
Stereo
FWD
SLOW
PAUSE/STILL
STOP
INDEX – SKIP INDEX +
NICAM ST
MONO
SET UP
VCR MENU
CH +
SET –
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
HiFi signal indication
It will be displayed for approx. 4
seconds when playing HiFi video
cassette tapes.
HI-FI
ENTER
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
ENTER
CH Ð
CANCEL
VIDEO Plus+
CANCEL
NICAM MONO A broadcast
"NICAM M1" illuminates when a
NICAM MONO A broadcast signal is
received.
VIDEO Plus+
NICAM M1
NICAM MONO A B broadcast
"NICAM M1/2" illuminates when a
NICAM MONO A and MONO B
broadcast signal is received.
Note:
When listening to a stereo broadcast or
playing back a tape Hi-Fi recorded in
stereo, you have to connect the DVD/
VCR with the stereo audio system or the
stereo TV. The sound which is output
from the RF OUT jack is monaural.
CH –
NICAM M1/2
NICAM OFF
It will be displayed for the NICAM
signal when the "NICAM [OFF]" is
selected in menu screen.
Note:
When playing HiFi cassette tapes recorded
on another VCR, the sound output may be
distorted. This is normal and no indication
of a unit malfunction. Try to minimize sound
distortions by using SET +/– or change to
MONO by pressing of AUDIO.
NICAM OFF
32
33
Audio Mixing
You can listen to both sound tracks (HiFi and MONO), by setting AUDIO MIXING mode.
VCR
Duplicating a Video Tape
Preparation:
• Turn ON the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
VCR MENU.
1 Press
to select
Press
or
DVD
VCR SETUP. Then press
ENTER.
OPEN/CLOSE
CLOCK
COUNTER
AUX
AUDIO
SUBTITLE
AUDIO SELECT ATR
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
AUTO REPEAT
a blank cassette tape with the erase prevention tab
REC/OTR and then PAUSE/STILL of Recording
3 Press
1 Load
intact into the recording DVD/VCR. Load the previously
unit.
recorded cassette tape into the playback VCR or a video
camera.
PLAY-button and then PAUSE/STILL-button of
4 Press
Playback unit. Now you can see the still picture of the
scene that you wish to duplicate.
[OFF]
VCR SETUP
SP
SYSTEM SETUP
ENTER
: ENTER
EXIT
: MENU
PAUSE/STILL of both units simultaneously to start
5 Press
the Duplicating.
VCR
CHANNEL SETUP
H
M
S
AUX or CH of the recording DVD/VCR to select the
2 Use
"LINE1", "LINE2" or "LINE3" instead of the preset channel.
SELECT :
ANGLE
COUNTER RESET
TV/VCR
TIMER REC SET
When you try to connect with a cable, make sure the power of both units have been turned off.
Connect the recording unit with the TV. Therefore you can just watch what the recording unit is recording.
Note:
Before starting the duplicating process, select the proper
tape speed using SP/LP. For a pre-recorded tape the
correct tape speed will be set automatically during
playback.
LINE1 = TV-RGB/Composite Scart Socket
2
Press
or
AUDIO MIX.
to select
LINE2 = VCR/DECODER Scart Socket
VCR SETUP
NICAM
[AUTO]
AUDIO MIX
SELECT :
PLAY
LINE3 = Front AV jacks
[OFF]
PLAYBACK SHARPNESS
Connection with second Video recorder or Video camera
/
ENTER
: ENTER
EXIT
: MENU
OR
REW
FWD
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
PAUSE/STILL
STOP
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
3
/
or ENTER to
Press
select [ON].
If you select [ON], the unit
will play both sound tracks
(Hi-Fi and MONO) until the
AUDIO MIXING mode is cancelled.
VCR SETUP
NICAM
[AUTO]
AUDIO MIX
Playback on
camera
Playback unit
[ON]
PLAYBACK SHARPNESS
SELECT :
/
ENTER
: ENTER
EXIT
: MENU
Recording unit
(not
supplied)
ENTER
CANCEL
CH Ð
VIDEO Plus+
4 Press VCR MENU repeatedly until the TV picture appears.
(not supplied)
Press AUX on the
recording unit repeatedly
until L3 appears.
Note:
To deactivate the AUDIO MIX function
follow the above procedure from steps 1
to 3, select [OFF], and confirm the setting
by pressing VCR MENU.
34
35
Disc
Setting setup language
The setup language can be selected.
This unit applies to DVD discs from Region 2 only.
The loaded Disc (DVD, Video-CD, Audio-CD and MP3-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Some CD-R/RW discs may be incompatible.
This DVD/VCR uses the PAL color system. The NTSC-DVDs can be playback on PAL 60Hz.
Do not play DVD-ROM, DVD-Audio, CDV, CD-G or Photo CD to prevent accidental erasure of prerecorded material.
VCR
Preparation:
• Turn ON the TV and set to the video input mode.
• When using an amplifier, switch on the amplifier.
DVD to select the DVD
1 Press
mode. (The DVD indicator will
DVD
light.)
“No Disc” will appear on the
screen. (If a DVD disc has already loaded, the playback will
start automatically.)
OPEN/CLOSE
Some DVDs is played back with a Copy guard system. In case of a dubbing on video tape, strong disturbance may
occur. This is not a defect of this DVD/VCR.
CLOCK
COUNTER
ANGLE
COUNTER RESET
Title
DVD DISC
When two or more movies are recorded on a disc,
the disc is divided into two or more sections. Each
section is called a “TITLE”.
TITLE1
CHAPTER 1
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
TITLE2
CHAPTER 2
CHAPTER 1
CHAPTER 2
CHAPTER 3
No Disc
SET UP in the stop mode.
2 Press
The SETUP MENU of DVD will
appear on the screen.
Then press
to select
or
“Language”.
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
Chapter
: Select
: Enter
PLAY
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Audio-CD
CD
Track
TRACK 1
TRACK 2
TRACK 3
REW
TRACK 4
TRACK 5
An Audio CD can contain several items.
These are assigned to the tracks.
FWD
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
ENTER
CH Ð
CANCEL
Press / to select On-Screen
3 Language,
then press ENTER.
VIDEO Plus+
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language ENG
PAUSE/STILL
STOP
: Select
/
to select desired
4 Press
language: English (English),
German (Deutsch) or French
(Français).
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
AB C
Language
On-Screen Language ENG English
Disc Menu Language ENG Fran ais
Audio Language
ENG Espa ol
Subtitle Language ENG
: Select
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
5
: Enter
: Enter
To make the SETUP screen disappear, press SET UP (or
RETURN).
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from centre to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
If the DVD/VCR does not operate
properly: Static electricity, etc., may
affect the player's operation. Disconnect
the AC power cord once, then connect
it again.
36
37
Playback procedure
Special playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
VCR
DVD
OPEN/CLOSE
1
Press OPEN/CLOSE.
The disc tray will open.
Note: There may be a slight delay between pressing the button and the
function activation.
VCR
DVD
TV/VCR
AUX
OPEN/CLOSE
a disc onto the tray.
2 Place
Hold the disc, position it with the
AUDIO
SUBTITLE
AUDIO SELECT ATR
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
printed label side up, align it with
the guides, and place it in its
proper position.
PLAY or OPEN/CLOSE.
3 Press
The disc tray closes automatically.
On the screen,
changes to
“
” and then playback will
commence.
PLAY
REW
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
ENTER
CANCEL
CH Ð
• A menu screen may appear on
the TV screen, if the disc has
a menu feature. In this case,
press , , ,
or ENTER
to operate a menu feature.
PAUSE/STILL
STOP
VIDEO Plus+
INSTANT SKIP
CLOCK
COUNTER
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
4
REW
SET UP
VCR MENU
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE/STILL during normal
playback.
PAUSE/STILL
STOP
CH +
SET Ð
Frame Advance
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
Press REW during normal playback.
Each press of REW will increase the speed of the search x2 ( ), x8
(
), x30 (
), x100 (
). (in case of Audio-CD: x4 ( ) and x8
) are available)
(
FWD
SLOW
INDEX Ð SKIP INDEX +
Press STOP to end playback.
• The DVD/VCR memorizes the stopped point, depending on
the disc. “To Return To The Last Scene Viewed, Press Play. To
Disable This Operation, Press STOP Again.” appears on the
screen for approx. 4 seconds. Press PLAY to resume playback
(from the scene point).
• If you press STOP again (“ ” appears on the screen) or
unload the disc, the DVD/VCR will clear the stopped point.
Review Playback
To resume normal playback, press
PLAY.
PLAY
FWD
Press FWD during normal playback.
Each press of FWD will increase the speed of the search x2 ( ), x8
), x30 (
), x100 (
). (in case of Audio-CD: x4 ( ) and x8
(
) are available)
(
• To resume normal playback, press PLAY.
CLOCK
COUNTER
ANGLE
COUNTER RESET
Fast Forward Playback
CH Ð
VIDEO Plus+
Press PAUSE/STILL during still playback.
One frame is advanced each time
you press PAUSE/STILL.
To resume normal playback, press
PLAY.
Slow-motion Playback
press OPEN/CLOSE.
5 Then
The disc tray opens.
, (POWER).
Remove the disc and press
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
• If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manual
for further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. In
this case, check your disc again (See pages 36 and 46, 47).
• Some discs may take a minute or so to start playback.
may appear at the upper right of the screen. This symbol means either the feature you
• A “Prohibition” symbol
tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate
a problem with the DVD/VCR.
• When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,
"
" will appear and remain on the screen for approx. 30 seconds and then it will change to "Please Check Disc".
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be
available. Also refer to the instructions supplied with the DVDs.
• When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid
possible damage to the audio system, the consumer should take proper precautions when the analog stereo
outputs of the DVD/VCR are connected to an amplification system.
38
NOTES:
• The unit is capable of holding a still
video image or On screen display image
on your television screen indefinitely. If
you leave the still video image or On
screen display image displayed on your
TV for an extended period of time, you
risk permanent damage to your
television screen. Projection televisions
are very susceptible.
• Some titles may not display chapter
numbers.
• When you set “Title Stop” to “Off” (See
page 53), you can access chapter in
another title. If you go back to the
preceding title by pressing the SKIP, the
DVD/VCR locates the first chapter of the
title. When “Title Stop” is set to “On”.
you can access chapters only within the
current title.
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4,
x1/8.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
Locating a chapter or track
T 1C 1
Press SKIP (
) Forward or SKIP
(
) Reverse during playback to
locate a chapter or track that you
want to watch.
Each time you press the button, a
“C (chapter)” number or “T (track)”
number is skipped.
), playback starts from the beginning
When you press SKIP (
of the current chapter or track.
) twice, playback starts from the
When you press SKIP (
beginning of the preceding chapter or track.
39
DVD Picture Signal Selection/Zooming
Repeat playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will
light)
You can select the output signal of
DVD playback picture to the TV
screen as an VIDEO signal or a RGB
signal.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
VCR
VCR
SET UP in the stop
1 Press
mode.
DVD
Press
or
to select “Picor
to
ture”, then press
select “Video Out Select”.
OPEN/CLOSE
CLOCK
COUNTER
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
CLOCK
COUNTER
Picture
TV Shape 4:3LB
Video Out Select Video
ENTER.
2 Press
or
Press
TV/VCR
: Enter
Picture
TV Shape 4:3LB
Video Out Select Video
SLOW
: Enter
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
E.A.M
PLAY MODE
SP/LP
RETURN
DISPLAY
CALL
CD
DVD
Chapter Repeat
Track Repeat
playback repeat playback will start automatically.
2 During
To start repeat playback during stop mode, press PLAY within
REW
3 To make SETUP screen disappear, press SET UP.
about 5 seconds after you press PLAY MODE.
• To resume normal playback, press PLAY MODE repeatedly
until “Off” appears on the TV-screen.
FWD
SLOW
PAUSE/STILL
STOP
Notes:
• If you use the connection with S-Video cord, be sure to set the
“Video Out Select” at step 2 above to “Video”. If you select “RGB”,
the TV screen will be disturbed.
• If you selected “RGB” at step 2 above, press TV/VCR to select
VCR. (VCR indicator will appear on the display) Otherwise, the
TV screen will be disturbed when you select the channel with
TV’s CHANNEL UP/DOWN buttons.
PAUSE/STILL
STOP
ZOOM
REC/OTR
PLAY
: Select
FWD
MEMORY
Video
RGB
PLAY
REW
Repeat” or “ All Repeat” )
AUDIO
SUBTITLE
AUDIO SELECT
ATR
AUX
TIMER REC
AB C
to select the
desired picture signal, “Video”
or “RGB”.
PLAY MODE repeatedly to select “Chapter Repeat”,
1 Press
“Title Repeat” or “All Repeat”. (In case of CD, select “Track
ANGLE
COUNTER RESET
: Select
AUDIO
SUBTITLE
AUDIO SELECT ATR
REPEAT PLAYBACK
OPEN/CLOSE
ANGLE
COUNTER RESET
TV/VCR
DVD
AB C
INDEX – SKIP INDEX +
SET UP
VCR MENU
CH +
SET –
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
CH –
VIDEO Plus+
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two
selected points.
A-B RPT during playback.
1 Press
The start point is selected.
ENTER
CH Ð
CANCEL
VIDEO Plus+
Zooming
A-
This unit will allow you to zoom in on the frame image. You
can then make selections by switching the position of the
frame.
A-B RPT again.
2 Press
The end point is selected.
Playback starts at the point that
you selected. Playback stops at
the end point, returns to Point A
automatically, then starts again.
ZOOM during playback.
1 Press
The centre part of the image
will be zoomed in.
As you repeatedly press the
ENTER or ZOOM while
“ZOOM” is selected, the magnification level changes. Variation of the levels includes
image reduction.
Notes:
• Picture Signal Selection is only
available for connecting with a 21 pin
Scart Cable.
• Depending on your TV, NTSC disc
may not playback correctly in colour. In
this case, it is recommended to select
the Picture Signal RGB on step 2.
• Only use RGB setting if your TV is
RGB compatible.
ZOOM
EXIT
Zoom Off
: Select
: Change
/
or /
to view a different part of the frame.
2 Press
You may move the frame from the centre position to UP,
DOWN, LEFT or RIGHT direction.
• If you select “EXIT” and press the ENTER, you can turn off
the symbol mark, keeping the current magnification level.
• Press CANCEL to restore the zoom point to the centre
of the picture.
“ZOOM” is selected, press ZOOM repeatedly to re3 While
turn to a 1:1 view.
40
NOTES:
• Some discs may not work with the
repeat operation.
• In A-B repeat mode, subtitles near
point A or B may not appear.
• During the A-B Repeat Playback the
ANGLE feature will not operate.
• You may not be able to set A-B Repeat, depending on the scenes of the
DVD.
• A-B repeat does not work with an interactive DVD and MP3-CD.
• Random playback can not be combined with Repeat playback.
To resume normal playback,
press A-B RPT again.
“Repeat Off” appears on the screen.
41
Memory playback/Random playback
MP3 Playback
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
VCR
You can arrange the order of titles, chapters or tracks on the disc.
This player can play back the MP3-data
which has been recorded on CD-R or CDRW. To produce the MP3-data, you need a
Windows-PC with CD-ROM drive and a MP3encoding Software (not supplied).
The Apple-HFS-System can not be played.
1 Press MEMORY.
MP3 CD Information
Memory playback
DVD
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
TV/VCR
AUX
MEMORY
ZOOM
In stop mode
1 T:- 2 T:- 3 T:- 4 T:- 5 T:- 6 T:- 7 T:- -
AUDIO
SUBTITLE
AUDIO SELECT
ATR
CT:- - CT:- - CT:- - CT:- - CT:- - CT:- - CT:- - -
Memory
: Select 0-9 : Input
TIMER REC
REC/OTR
PLAY MODE
SP/LP
RETURN
DISPLAY
CALL
2
REW
FWD
SLOW
PAUSE/STILL
STOP
INDEX – SKIP INDEX +
SET UP
VCR MENU
CH +
SET –
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
CH –
: Select 0-9 : Input
: Play
Press
/
to
In stop mode
In playback
select “T” Title
number or “CT”
Chapter or Track
number. Use
Memory
Memory
number keys to
: Select 0-9 : Input
: Play
: Select 0-9 : Input
: Play
Input the favorite
number.
• If you input a large number than the number that is recorded
on the disc, the bar will be skipped.
• The input number into "T" for CD or MP3 is not effective.
or ENTER.
3 Press
Set the “T” and
“CT” in the next
bar as In step 2.
ENTER
CANCEL
: Play
1 T:01 CT:002
2 T:- - CT:- - 3 T:- - CT:- - 4 T:- - CT:- - 5 T:- - CT:- - 6 T:- - CT:- - 7 T:- - CT:- - -
PLAY
In playback
1 T:- - CT:- - -
Memory
E.A.M
VIDEO Plus+
1 T:01 CT:002
In stop mode
1 T:01
2 T:02
3 T:- 4 T:- 5 T:- 6 T:- 7 T:- -
CT:002
CT:004
CT:- - CT:- - CT:- - CT:- - CT:- - -
In playback
2 T:02 CT:004
Memory
: Play
: Select 0-9 : Input
: Play
• When you select another chapter In the same title, you do
not need to select the title number.
• To cancel the programmed selection, press CANCEL.
4 Press PLAY to start MEMORY playback.
• To resume normal playback, press CANCEL.
Random playback
1
NOTES:
• The memory playback is cancelled
when press STOP during memory
playback.
• Random playback can not be
combined with Repeat playback.
• You can program up to 30 selections
into the memory.
• Depending on the DVD, Chapter
Random operation may not work
during playback.
• You cannot use the random playback
with memory playback.
42
Press PLAY MODE repeatedly to select “ Chapter Random”
or “Title Random”.(In case of CD, select Track Random)
DVD
Chapter Random
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits
extension letters, “mp3”.
• The directory and file names of the MP3
CD must correspond to the ISO
standardized files.
• This unit can read 200 files per disc. If
one directory has more than 200 files, it
reads up to 200 files, the remaining files will
be omitted.
• As for multi-session disc, only the first
session can be played.
• If the CD has both audio tracks and MP3
files, only audio tracks are played.
• It may take more than one minute for this
unit to read MP3 files depending on its
structure.
• Music recorded by “Joliet Recording
Specification” can be played back, the file
name is displayed (within 8 letters) on the
screen. Long file names will be condensed.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Memory
: Select 0-9 : Input
A-B
CD
Track Random
playback random playback will start automatically.
2 During
To start random playback during stop mode, press PLAY
within about 5 seconds after you press the PLAY MODE.
• To resume normal playback, press PLAY MODE repeatedly
until “Off” appears on the TV-screen.
Limitations on display
The maximum number for display is 8
letters. Available letters for display are the
following: capital or small alphabets of A
through Z, numbers of 0 through 9, and _
(under score).
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data
alphabetically or numerically.
2. Name each file including a two-digit or threedigit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
• Some MP3 CDs can not be played back
depending on the recording conditions.
• The CD-R/RW that has no music data or
non-MP3 files can not be played back.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will
light)
OPEN/CLOSE.
1 Press
The disc tray will open.
Place a disc onto the tray.
PLAY or OPEN/CLOSE.
2 Press
The disc tray closes automatically.
T
11
On the TV-screen, “
” and then
reading file number will appear.
Then playback will commence.
• Reading will take as much time
as the number of file.
• Press STOP to end playback.
Press DISPLAY.
3 Then
/
press
to select
and press ENTER.
MP3
T 1
MP3
000:23
EAM
PCM
: Select
: Enter
Press / or / to select the desired track, then press
4 ENTER.
Track is selected and play commences.
/
• In case the folder includes more than 9 tracks, press
to display next track list.
• To remove track list, press CANCEL.
to select “T” and press number keys to
• Press /
input your desired track.
T 1
MP3
000:23
1. \ CRYINI~1
2. \ DANGER~1
3. \ GITARREN
4. \ LILYWA~1
5. \ MERCYS~1
6. \ OBSESS~1
7. \ PINKPA~1
8. \ RUNNIN~1
: Select
EAM
PCM
: Search
STOP to end playback.
5 Press
• The unit records the stopped track.
Press PLAY to resume playback (from the beginning of
track).
• If you press STOP again or unload the disc, the unit will
clear the stopped track.
OPEN/CLOSE.
6 Press
The disc tray opens.
.
Remove the disc and press
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
• During MP3-Playback, you can not use SEARCH, A-B
Repeat functions.
• You can use Repeat(Track or All), Memory and Random functions
for MP3 CD Playback.(See page 41 and 42)
43
Changing soundtrack language / Changing Subtitles language
Changing angles / Title selection / DVD menu
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
TV/VCR
AUDIO
SUBTITLE
AUDIO SELECT ATR
AUX
Changing soundtrack language
MEMORY
ZOOM
E.A.M
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
2CH
ENG2
5.1CH
FRE1
2CH
ANGLE
COUNTER RESET
TV/VCR
: Select
The on-screen display will disappear after a few seconds.
• To turn off the soundtrack
setting display, press the
CANCEL or ENTER button.
FWD
PAUSE/STILL
STOP
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
2CH
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
ENG1
ENG2
FRE1
: Return
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
CH Ð
Angle :1
: Select
PLAY
2CH
: Return
REW
2CH
SLOW
/
: Return
repeatedly until the desired angle is
• To turn off the angle number display, press the CANCEL.
• You can change the camera angle directly by pressing the
number keys corresponding to its angle number instead of
using the
/ buttons.
FWD
PAUSE/STILL
STOP
In case of VIDEO CD playback
Audio type changes as follows each time you press AUDIO.
Title Selection
INDEX – SKIP INDEX +
SET UP
VCR MENU
VIDEO Plus+
L.R
L.R
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
L.R
L
L
L
R
R
R
SET –
ENTER
CANCEL
NOTES:
• If the desired language is not heard after
pressing AUDIO several times, the
language is not recorded on the disc.
• Changing soundtrack or subtitle
language is cancelled when you open the
disc tray or turn the power off. The initial
default language or available language
will be heard and seen if the disc is
played back again.
• Depending on the DVD you may be
unable to turn on, turn off, or change the
subtitles, even if they are recorded on the
disc. While playing the DVD, the subtitle
may change while opening or closing the
disc tray, or while changing the title.
• During some scenes, the subtitles may not
appear immediately after you select “On”.
• The abbreviation of the language
appears instead of the language name.
Refer to the list of languages and their
abbreviations. (See on page 57.)
1
2
3
Press ANGLE or
2 selected.
ENTER
CANCEL
ANGLE during playback.
1 Press
The current angle will appear.
AUDIO
SUBTITLE
AUDIO SELECT
ATR
AUX
2CH
5.1CH
2CH
Audio:ENG1
: Select
When playing back a disc recorded with multi-angle facility, you
can change the angle that you are viewing the scene from.
2CH
AUDIO repeatedly until
2 Press
the desired language is selected.
REW
SLOW
OPEN/CLOSE
CLOCK
COUNTER
ENG1
Audio:FRE1
PLAY
Changing Angles
DVD
AUDIO during playback.
1 Press
The current soundtrack language
is displayed.
PLAY MODE
SP/LP
VCR
You can select the language when you play a multilingual disc.
CH –
TITLE during playback.
1 Press
Title menu appears on the screen.
VIDEO Plus+
• Press TITLE again to resume playback at the scene
when you pressed TITLE.
2 Press / or / to select the desired title.
ENTER or PLAY.
3 Press
The playback of the selected title will start.
Changing Subtitles language
You can select the language when playing back a disc recorded
with multi-lingual subtitles.
SUBTITLE during
1 Press
playback.
/
to select the
Then press
desired language.
• To turn off the subtitle setting
display, press the CANCEL
or ENTER button.
• To turn the subtitles off, select
“Off”.
Two or more titles are recorded on some discs. If the title menu
is recorded on the disc, you can select the desired title.
DVD Menu
Some DVDs allow you to select the disc contents using the
menu.
When you play back these DVDs, you can select the subtitle
language and sound-track language,etc. using the DVD menu.
Off
GER 1
DUT 1
SV 1
NO 1
Subtitle:- - - Off
: Select
: Return
MENU during playback.
1 Press
The DVD menu appears on the screen.
NOTE:
Depending on the DVD, you may not
be able to change the angles even if
multi-angles are recorded on the disc,
or you may be unable to select the title,
and a “title menu” may simply be called
a “menu” or “title” in the instructions
supplied with the disc.
SUBTITLE repeatedly to
2 Press
turn Subtitles on or off.
Off
GER 1
DUT 1
SV 1
NO 1
Subtitle:- - - Off
: Select
: Return
• Press MENU again to resume playback at
the scene when you pressed MENU.
2 Press
3
/
or
/
to select the desired item.
Press ENTER.
The menu continues to another screen. Repeat steps 2 and 3 to
set the item completely.
44
45
Parental control
Some discs are specified not suitable
for children. Such discs can be
prevented from play back with the
unit.
Parental control
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
Parental control setting
VCR
SET UP in the stop mode.
1 Press
Press or to select “Opera-
DVD
AB C
Picture
TV Shape 4:3LB
Video Out Select
tion”.
OPEN/CLOSE
CLOCK
COUNTER
: Select
ANGLE
COUNTER RESET
TV/VCR
AUX
SUBTITLE
AUDIO
AUDIO SELECT ATR
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
2
Press
or
to select
“Parental Lock”, then press
ENTER.
: Enter
Auto Off
Off On
Off
On
: Select
Code
AU
BE
CA
CN
HK
DK
FI
FR
DE
ID
IT
JP
MY
Country/Area
NETHERLANDS
NORWAY
PHILIPPINES
RUSSIAN FEDERATION
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
/ to select the paren6 Press
tal lock level, then press ENTER.
AB C
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Country/Area
AUSTRALIA
BELGIUM
CANADA
CHINA
CHINA HONG KONG
DENMARK
FINLAND
FRANCE
GERMANY
INDONESIA
ITALY
JAPAN
MALAYSIA
AB C
Operation
Pause/Still
Parental Lock
Title Stop
PBC
: Select
FWD
SLOW
PAUSE/STILL
STOP
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
CH Ð
VIDEO Plus+
3 Press
or
NOTES:
• If each setup (page 46~55) has been
completed, the unit can always be
worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the
memory if you turn the power off.
• Depending on the discs, the unit cannot limit playback.
• Some discs may not be encoded with
specific rating level information though
its disc jacket says "adult". For those
discs, the age restriction will not work.
• Do not forget the security code. If you
forget the security code, delete it. (See
step 7 on next page)
GB
7
: Enter
to select Off or On.
Off: The parental lock feature
does not function.
After pressing ENTER,
follow step 4 and 6 below.
On: To activate the parental lock
feature or change the
setting, press ENTER and
follow steps 4-6 below.
AB C
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Example: Set to GB (UNITED
KINGDOM).
or
to select “G” then
Press
press
to move to the right
character. Then select “B” same
as above. Then press ENTER.
: Enter
• Level 1: DVD software for adults cannot be played back.
• Level 8: All DVD software can be played back.
• Select from the level 1 to level 8. The limitation will be more severe
as the level number is lower.
AB C
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto Off
Off On
Off Security Code ---On
: Select
the code of a country/area
5 Enter
whose standards were used to
rate the DVD disc. (See the list
on the page 47)
You cannot play DVD discs rated higher than the level you selected
unless you cancel the parental lock function.
For example, when you select level 7, discs rated higher than level
7 are locked out and cannot be played.
Auto Off
Off On
Off
On
: Select
number keys to input a
4 Press
4-digits security code then
press ENTER.
• If you input a wrong number,
press CANCEL.
• To return to the before step,
press RETURN.
46
Auto Off
Off On
Off Area Code
On Level
: Enter
PLAY
REW
Code
NL
NO
PH
RU
SG
ES
SE
CH
TW
TH
GB
US
7 To make the SETUP screen disappear, press SET UP.
To change the parental lock level
Follow steps 1- 6.
: Enter
To change your 4-digit security code
AB C
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto Off
Off On
Off Area Code
On
: Select
GB
1) After selecting “On” or “Off” at step 3 press STOP four times, then
press ENTER.
The 4-digit security code is deleted.
2) Press number keys to create a new 4-digit security code at step 4.
: Enter
47
Setting menu language
You can select the language of the
disc menu messages of DVDs.
Setting audio soundtrack language
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
SET UP in the stop mode.
1 Press
or
to select “LanPress
DVD
VCR
: Select
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
“Language”.
DVD
OPEN/CLOSE
CLOCK
COUNTER
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
SET UP in the stop mode.
1 Press
Press
or
to select
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
guage”.
VCR
The same audio soundtrack language
can always be selected by your unit
even if you replace the disc or turn
the power off.
OPEN/CLOSE
: Enter
CLOCK
COUNTER
Press
or
to select “Disc
2 Menu
Language”.
Language
On-Screen Language ENG English
Disc Menu Language ENG Fran ais
Audio Language
ENG Espa ol
Subtitle Language ENG
: Select
: Select
: Enter
ANGLE
COUNTER RESET
AB C
: Enter
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
or
2 Press
Language”.
to select “Audio
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language ENG
: Select
ENTER.
3 Press
Press
or
PLAY
REW
to select your
desired language, then press
ENTER.
FWD
SLOW
PAUSE/STILL
STOP
Language
On-Screen Language ENG English
Disc Menu Language DE French
Audio Language
ENG German
Subtitle Language ENG Others
Code D E
: Select
: Enter
PLAY
AB C
REW
FWD
SLOW
PAUSE/STILL
STOP
: Enter
ENTER.
3 Press
Press
or
to select your
desired Audio Language, then
press ENTER.
AB C
Language
On-Screen Language ENG English
Disc Menu Language ENG French
Audio Language
DE German
Subtitle Language ENG Others
Code D E
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
SET Ð
English, French, German
The selected language is the first-priority Menu language.
Others:
ENTER
CH Ð
CANCEL
VIDEO Plus+
Other languages can be selected (See the Table of
languages on page 57).
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
TITLE
A-B RPT
MENU
ZERO RETURN
SET Ð
INSTANT SKIP
SET +
ENTER
CH Ð
CANCEL
VIDEO Plus+
Example:
Set to EN (ENGLISH).
Press
or
to select “E” then press
to move to
the right character. Then select “N” same as above.
Then press ENTER.
: Select
: Enter
English, French, German
The language you have selected will play if it is recorded on
the disc.
Others:
If you want to select another language, enter the language code (See the Table of languages on page 57).
Example:
Set to EN (ENGLISH).
Press
or
to select “E” then press
to move to
the right character. Then select “N” same as above.
Then press ENTER.
4 To make the SETUP screen disappear, press SET UP.
4 To make the SETUP screen disappear, press SET UP.
NOTES:
• If the selected language is not recorded on the disc, the original language will be heard.
• Some DVD discs may be played in a
different language than you selected.
A prior language may be programmed
on the disc.
48
49
Setting subtitle language
The same subtitle language can
always be selected even if you replace
the disc or turn the power off.
Setting the aspect ratio of TV screen / Setting on Screen display
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
SET UP in the stop mode.
1 Press
or
to select
Press
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
OPEN/CLOSE
CLOCK
COUNTER
ANGLE
COUNTER RESET
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
AUX
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
: Select
or
2 Press
Language”.
TV/VCR
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language ENG
: Select
FWD
ENTER.
3 Press
or
Press
to select your
desired language, then press
ENTER.
PAUSE/STILL
STOP
CH +
SET Ð
TITLE
A-B RPT
CH Ð
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
REC/OTR
RETURN
DISPLAY
CALL
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
: Select
ENTER.
2 Press
Press
or
to select your
desired screen type.
: Enter
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
4:3 Letterbox
4:3 Normal
16:9 Widescreen
: Select
REW
English
French
German
No Subtitle
Others
MENU
ZERO RETURN
SET +
INSTANT SKIP
FWD
: Enter
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
CH +
SET Ð
English, French, German
The subtitle is displayed with the selected language if it is
recorded on the disc.
VIDEO Plus+
PAUSE/STILL
STOP
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
CH Ð
VIDEO Plus+
: Enter
NOTES:
• If the selected language is not recorded
on the disc, the first-priority language is
selected.
• Some DVD discs may be set to display
subtitles in a different language than you
selected. A prior subtitle language may
be programmed on the disc.
4
To make the SETUP screen disappear, press SET UP.
4:3 Normal:
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen. Either or both
sides of the picture are cut off.
16:9 Widescreen:
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
Setting on Screen display
Others:
If you want to select another language, enter the
language code (See the Table of languages on
page 57).
Example: Set to EN (ENGLISH).
or
to select “E” then press PLAY to move
Press
to the right character. Then select “N” same as above.
Then press ENTER.
4:3 Letterbox:
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars above and below
the picture.
3 To make the SETUP screen disappear, press SET UP.
No Subtitle:
Subtitles do not appear.
50
or
PLAY
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language
ENG
Subtitle Language
AA
: Select
ENTER
CANCEL
AUDIO
SUBTITLE
AUDIO SELECT ATR
TIMER REC
: Enter
Code A A
SET UP
VCR MENU
“Picture”, then press
to select “TV shape”.
You have the following screen sizes to choose from:
REW
INDEX Ð SKIP INDEX +
AUX
to select “Subtitle
AB C
SET UP in the stop mode.
1 Press
or to select
Press
ANGLE
COUNTER RESET
: Enter
PLAY
SLOW
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
Setting the aspect ratio of TV screen
VCR
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
“Language”.
DVD
You can select the aspect ratio for
your TV.
NOTES:
• The displayable picture size is preset on
the DVD video disc. Therefore, the
playback picture of some DVD video
discs may not conform to the picture size
you select.
• When you play DVD video discs recorded in the 4:3 picture size only, the
playback picture always appears in the
4:3 picture size regardless of the TV
shape setting.
• If you select “16:9 widescreen” and you
own a 4:3 TV set, the DVD playback
picture will be horizontally distorted during playback. Images will appear to be
horizontally compressed. Always be
sure that your TV shape conforms to the
actual TV in use.
SET UP in the stop mode.
1 Press
Press
or
to select “Display”
or
to select “On2 Press
Screen Displays”.
AB C
Display
On-Screen Displays On
Background
Picture
Screen Saver
On
: Select
ENTER.
3 Press
Press
or
to select “On” or
“Off”.
On:
Off:
: Enter
AB C
Display
Off
On-Screen Displays Off
Background
Picture On
Screen Saver
On
Operational modes (e.g.
“ ”, “ ”) appear when you
press the buttons (factory
setting).
Operational modes (e.g. “ ”, “
you press any buttons.
: Select
: Enter
”) do not appear when
4 To make the SETUP screen disappear, press SET UP.
51
Setting Audio
Setting Operation
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
Audio Out Select
Select the output sound format corresponding to your system connection.
For details of sound recording systems, see on page 55.
VCR
DVD
OPEN/CLOSE
CLOCK
COUNTER
SET UP in the stop mode.
1 Press
or
to select “Audio”.
Press
or
to select “Audio Out
2 Press
Select”, then press ENTER. Press
or
to select your desired output sound.
ANGLE
COUNTER RESET
TV/VCR
AUX
AUDIO
SUBTITLE
AUDIO SELECT ATR
MEMORY
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
PLAY
REW
FWD
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
PAUSE/STILL
STOP
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
SET +
INSTANT SKIP
ENTER
CANCEL
CH Ð
VIDEO Plus+
: Select
Bitstream
Analog 2ch
PCM
3 To make the SETUP screen disappear, press SET UP.
Dynamic Range Control
Turn on or off a function that makes faint sounds easier to hear
even if you lower the volume during late hours playback.
AB C
Audio
Audio Out Select
Bitstream
Dynamic Range Control On
Karaoke Vocal
Off
Press
Off:
On:
or
: Select
Off
On
: Enter
to select “On” or “Off”.
or
to
2 Press
select “Pause/Still”,
2
Operation
Pause/Still
Auto
Parental Lock Off
Title Stop
Off
PBC
On
then press ENTER.
Press
or
to
select “Auto” or
“Frame”, then press
ENTER.
: Select
SET UP in the stop mode.
1 Press
or
to select “Audio”.
Press
AB C
Audio
Audio Out Select
Bitstream
Dynamic Range Control On
Karaoke Vocal
Off
or
to select “Karaoke
2 Press
Vocal”, then press ENTER.
Press
Off:
On:
or
: Select
Off
On
: Enter
to select “On” or “Off”.
3 To make the SETUP screen disappear, press SET UP.
: Enter
AB C
Operation
Pause/Still
Auto
Parental Lock Off
Title Stop
Off
PBC
On
Off
On
: Select
: Enter
Auto: For normal use. Still and fast motion images
can be paused.
Frame: The resolution of still pictures is improved,
so that you can make a motionless picture
clearer when you pause it.
: Enter
Off: When playing a VIDEO CD without using
the menu.
On: To use the menu when playing a PBCfeatured VIDEO CD.
make the SET UP screen disappear, press SET
3 To make the SETUP screen disappear, press SET UP. 3 To
UP.
Title Stop
Turn on or off a feature that automatically stops
playback after a title has been viewed.
SET UP in the
1 Press
stop mode.
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
or
to
2 Press
select “Title Stop”,
Operation
Pause/Still
Parental Lock
Title Stop
PBC
Auto
Off
Off
On
Off
On
: Select
Off:
: Enter
AB C
then press ENTER.
Press or
to
select “On” or “Off”,
then press ENTER.
On:
The primary vocal is not output.
The primary vocal is output when
it is recorded on the disc.
: Enter
to select “PBC”, then press ENTER.
to select “On” or “Off”, then press
Auto
Frame
: Select
Karaoke Vocal
Turn on or off the vocal output during DVD KARAOKE disc
playback.
Press
or
Press
or
ENTER.
AB C
make the SETUP screen disappear,
3 To
press SET UP.
NOTES:
• The Dynamic Range Control function
works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Control
may differ depending on the DVD video
disc.
• The vocal output feature is used during
playback of Dolby Digital (multi-channel)
recorded DVD KARAOKE discs. This
feature allows you to turn off vocal audio
tracks, or restore them for background
accompaniment.
• When playing KARAOKE, connect the
appropriate audio equipment such as an
amplifier to the DVD player.
Picture
TV Shape 4:3LB
Video Out Select Video
: Select
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
to
Press or
select “Operation”.
Press
or
to select “Operation”.
Full dynamic range is maintained.
Dynamic range is reduced.
AB C
or to
Press
select “Operation”.
: Select
Select when connected to an amplifier equipped with a Dolby
Digital, DTS, MPEG1 or MPEG2 decoder. The DVD/VCR outputs
digital audio information in the bitstream format when you play a
DVD video disc recorded on the Dolby Digital, DTS, MPEG1 or
MPEG2 recording system.
Analog 2ch: Select when connected to a TV, Dolby Pro Logic or stereo system
via the analog audio jacks.
PCM:
Select when connected to a 2 channel digital stereo amplifier.
The DVD/VCR outputs sounds in the PCM 2ch format when you
play a DVD video disc recorded on the Dolby Digital. MPEG1 or
MPEG2 recording system.
or
to select “Dynamic
2 Press
Range Control”, then press ENTER.
SET UP in
1 Press
the stop mode.
: Enter
Bitstream:
SET UP in the stop mode.
1 Press
or
to select “Audio”.
Press
PBC
Pause/Still
Select the resolution of still pictures.
SET UP in the
1 Press
stop mode.
AB C
Audio
Audio Out Select
Bitstream
Dynamic Range Control On
Karaoke Vocal
On
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD
indicator will light)
: Enter
The DVD/VCR continues after playback of
a title is completed.
The DVD/VCR stops after playback of a title
is completed.
make the SETUP screen disappear,
3 To
press SET UP.
52
53
Selecting the sound enhancement (E.A.M.)/Setting Background/
Setting Screen Saver
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD
indicator will light)
Setting Background
Select the background color or background picture.
or
to sePress
lect “Display”.
You can easily switch a preferred audio enhancement.
AB C
: Select
or
2 Press
select “Back-
2
Dialogue:
To control critical centre channel information
to make dialogue more intelligible (only
when playing a DVD video disc recorded on
the Dolby Digital recording system).
• To use this enhancement on sounds output
from the BITSTREAM/PCM jack, be sure to
set “Audio Out Select” to “PCM.” (see page 55).
54
ZOOM
E.A.M
PLAY MODE
SP/LP
TIMER REC
REC/OTR
RETURN
DISPLAY
CALL
Setup”.
Blue
Gray
Screen Saver
Picture
On
: Enter
PLAY
Jacket
: Select
AB C
Picture
TV Shape 4:3LB
Video Out Select Video
: Select
Display
On-Screen Display On
Background Picture
REW
ENTER, then press
2 Pressto select
“On-Screen
FWD
SLOW
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
PAUSE/STILL
STOP
CH +
SET Ð
TITLE
A-B RPT
MENU
ZERO RETURN
CH Ð
SET +
INSTANT SKIP
AB C
Initial Setup
On-Screen Language ENG
TV Shape
4:3LB
Audio Out Select
Bitstream
: Select
On-Screen Language:
TV Shape:
Audio Out Select:
ENTER
CANCEL
or
Language”, “TV Shape” or
“Audio Out Select”.
: Enter
English
Fran ais
Deutsch
Espa ol
: Enter
See on page 37.
See on page 51.
See on page 52.
VIDEO Plus+
3 To make the SETUP screen disappear, press SET UP.
Output sound conversion table (sampling frequency/quantization bit)
You can select the output sound format corresponding to your system connection (see page 52).
Setting Screen Saver (DVD only)
To turn the screen saver on or off.
or to
Press
select “Display”.
Bitstream
Discs
SET UP in the
1 Press
stop mode.
Dolby Digital
Picture
TV Shape 4:3LB
Video Out Select Video
: Select
or
to
2 Press
select “Screen
Saver”, then press
ENTER.
Press or
to
select “On” or “Off”,
then press ENTER.
3
Recording system
AB C
CANCEL.
Spatializer® 3-Dimensional Sound Processing provided by
Desper Products. Inc.
Certain audio features of this product manufactured under
a license from Desper Products, Inc., Spatializer® and the
circle-in-square device are trademarks owned by Desper
Products, Inc.
MEMORY
make the SETUP screen disappear, press SET
3 To
UP.
To exit the audio enhancement selection Press
Notes:
• Actual effects to sounds may vary depending on the speaker
system. Make selection according to your preference.
• Actual effects to sounds may vary depending on the disc.
• When the DVD/VCR is connected to an amplifier equipped
with Dolby Pro Logic Surround, select “Normal”.
Otherwise, Dolby Pro Logic Surround may function
differently than usual.
• Selecting “Dialogue” disables “Dynamic Range Control”
function (see page 52).
• During MP3 playback, the sound enhancement is not
effective.
AUX
AB C
Blue:
Blue background.
Gray:
Gray background.
Picture: Use the picture which appears when you
turn on the DVD/VCR as a background.
Jacket: Use the jacket picture included on some
discs as a background. If it is not included,
a gray background will be substituted.
Normal:
Normal sound.
3D:
To obtain expansive virtual surround sound
effects from just two speakers.
: Enter
SET UP in the stop mode.
1 Press
to select “Initial
Press or
AUDIO
SUBTITLE
AUDIO SELECT ATR
TV/VCR
to
ground”, then press
ENTER. Press
or
to select your
desired background, then press
ENTER.
Select the sound enhancement by pressing / .
Each time you press the button, the sound enhancement changes.
Setting initial setup
ANGLE
COUNTER RESET
Picture
TV Shape 4:3LB
Video Out Select Video
*E.A.M.: Enhanced Audio Mode
1 Press E.A.M.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press DVD to select the DVD mode. (The DVD indicator will light)
CLOCK
COUNTER
SET UP in the
1 Press
stop mode.
Selecting the sound enhancement (E.A.M.*)
Setting initial setup/output sound conversion table
You can install the initial system
setting.
: Enter
AB C
Display
On-Screen Display On
Background Picture
Screen Saver On
Off
On
48 kHz/16 bit
48 kHz/20 bit
DVD video
48 kHz/24 bit
Linear PCM
discs
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG1, MPEG2
CDs
: Select
Linear PCM 44.1 kHz/16 bit
DTS
Analog 2ch
PCM
DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO DIGITAL AUDIO ANALOG AUDIO
OUT jack
OUT jack
OUT jack
OUT jack
OUT jack
OUT jack
Bitstream
48 kHz/20 bit
48 kHz/16 bit 48 kHz/16 bit
48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/24 bit
48 kHz/16 bit 48 kHz/16 bit
48 kHz/16 bit 48 kHz/20 bit
48 kHz/16 bit 48 kHz/24 bit
Bitstream
—
Bitstream 48 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit
Bitstream
(Noise)
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
—
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
—
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
—
—
—
—
Bitstream
Bitstream
48 kHz/16 bit 48 kHz/16 bit 48 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit 44.1 kHz/16 bit
Bitstream
(Noise)
Bitstream
(Noise)
: Enter
Off: The screen saver is disengaged.
On: The screen saver operates in 10
minutes after you press PAUSE/
STILL.
To make the SETUP screen disappear, press SET
UP.
55
Status display of Disc
Table of languages
You can view information on the operation status and access and settings.
1
Enter the appropriate code for the initial settings"Menu", "Audio" and/or "Subtitle" (see pages 48~50).
With each press of DISPLAY, the status of the disc will appear on the screen and change as follows.
Symbol mark of the feature
you selected is displayed.
DVD
T 2C 3
T 2C 3
0:08:16
-0:21:28
Audio/
Video CD
ZOOM
T 1
-03:38
EAM
EPM
EAM
EAM
EAM
2CH
2CH
PCM
PCM
ZOOM
X
C
C
1
1
OFF
OFF
0:08:16
T 1
00:30
–––
ZOOM
X
EAM
T 2C 3
Abbreviation Language
mark is only for
Video CD.
BIT
RATE
9.2Mbps
T 2C3
T 1
EAM
EAM
2CH
2CH
ZOOM
X
ZOOM
X
C
C
1
1
T 1
01:14
----- CD TEXT ----Disc Title:
No Text
Track Title:
No Text
EAM
EAM
PCM
PCM
(Audio CD only)
2
Press
or
to select the desired symbol mark, then press ENTER.
T : Title number (Track number)
/
or number keys to locate a title or
Press
track, then press ENTER.
: Elapsed (remaining) time of the current title
Press number keys to locate a desired Location,
then press ENTER.
C : Chapter number
Press
/
or number keys to locate a Chapter,
then press ENTER.
Audio setting
See page 44.
: Angle setting
See page 45.
: Subtitle setting
See page 44.
: E.A.M. (Enhanced Audio Mode)
See page 54.
ZOOM
: To zoom a picture
See page 40.
: Audio Out Select setting
BST: Bitstream 2CH:Analog 2ch PCM:PCM
See page 52.
: To stop playback
See page 38.
: Playback starts from the beginning of the
current chapter or track.
See page 39.
: Fast reverse playback
See Page 39.
: To start playback
See page 38.
: Fast forward playback
See page 39.
: To locate succeeding chapters or tracks.
: To begin slow motion playback
See page 39.
See page 39.
: To pause playback
See page 39.
: To turn off the display
CD TEXT
Displays CD text data if included on the audio
CDs. (Some letters may not be displayed
properly depending on the disc.)
Data transfer rate (Mbit/s)
Amount of picture, sound and subtitle data in the DVD
video disc transferred per second.
The larger the value is, the more data processed, but
this does not necessarily insure better picture quality.
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
AY
AZ
BA
BE
BG
BH
BI
BN
BO
BR
CA
CO
CS
CY
DA
DZ
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
No alternate
language
Chinese
Dutch
English
French
German
ltalian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
Abbreviation Language
GN
GU
HA
HI
HR
HU
HY
IA
IE
IK
IN
IS
IW
JI
JW
KA
KK
KL
KM
KN
KS
KU
KY
LA
LN
LO
LT
LV
MG
MI
MK
ML
MN
MO
MR
MT
MY
NA
NE
NO
OC
OM
OR
PA
PL
PS
Abbreviation Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
PT
QU
RM
RN
RO
RU
RW
SA
SD
SG
SH
SI
SK
SL
SM
SN
SO
SQ
SR
SS
ST
SU
SV
SW
TA
TE
TG
TH
TI
TK
TL
TN
TO
TR
TS
TT
TW
UK
UR
UZ
VI
VO
WO
XH
YO
ZU
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
56
57
Problems and troubleshooting
Problems and troubleshooting / Video head cleaning
Use the following check list for troubleshooting when you have problems with your unit. Consult your local
dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
SYMPTOMS
POSSIBLE SOLUTIONS
SYMPTOMS
PAGE
DVD/VCR
DVD/VCR does not operate.
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
• Select the DVD or VCR mode before operating.
No picture.
• Antenna connection is not correct or antenna cable is disconnected.
10
• The video channel is not in the correct position or the TV is not
13
set to the video channel.
• Check the unit is connected correctly.
10~12
• The video input selector of the TV is not set to VIDEO. Set to
–
VIDEO (or equivalent).
• Channel is set to the external mode.
–
No sound.
The remote control does not
function.
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
• Aim the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
–
–
–
–
14,37
POSSIBLE SOLUTIONS
PAGE
No 4:3 (16:9) picture
• The setup does not match your TV.
51
No on-screen display
• Select Display On.
51
No surround sound
• The setup does not match your stereo system.
12
The unit or remote operation key
is not functioning.
• Turn off the unit and unplug the AC power cord for several
minutes, then replug it.
14
Playback does not start when the
title is selected.
Audio soundtrack and/or subtitle
language is not changed when
you play back a DVD.
• Check the Parental control setting.
46
• Multilingual language is not recorded on the DVD disc.
49,50
No subtitle
• Some discs have no subtitles.
• Subtitles are cleared. Press SUB TITLE.
50
44
Angle cannot be changed.
• Multi-angles are not recorded on the DVD disc.
45
• The function is prohibited with the unit or the disc.
–
appears on the screen.
10~12
–
20,39
Video head cleaning
9
VCR
TV recording does not work.
• The erase prevention tab of the video cassette is broken off.
• The unit is in the external input mode.
18
Timer recording does not work.
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER REC has not been pressed ( is not lit).
15
29
30
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
• The tape is worn or damaged.
20
Noise bars on screen.
59
–
Video head clogging
The video heads are the means by which the DVD/VCR reads
the picture from the tape during playback. In the unlikely event
that the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if,
during playback of a known good tape, there is good sound,
but no picture (picture is extremely snowy). If this is the case,
have the DVD/VCR checked by qualified service personnel.
Good Picture
Snowy Picture
NOTES: • DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
REAR COVER.
• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
DVD
Display is not shown in your
language.
• Select proper language in the menu options.
37
Playback doesn’t start.
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
38
36
36
Stopping playback, slow-motion
play, repeat play, or memory play,
etc. cannot be performed.
• Some discs may not do some of the functions.
–
58
59
IMPORTANT WARNING
CAUTION:
DVD PLAYER IS A CLASS 1 LASER PRODUCT. HOWEVER THIS PLAYER USES A VISIBLE LASER
BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO
OPERATE THE PLAYER CORRECTLY AS INSTRUCTED.
THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE PLAYER.
CLASS 1
LASER PRODUCT
(Printed on the Rear Panel)
WHEN THIS PLAYER IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE
TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF
THIS PLAYER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED
PERSONNEL.
SERVICING NOTICES ON CHECKING
1. KEEP THE NOTICES
As for the places which need special attentions,
they are indicated with the labels or seals on the
cabinet, chassis and parts. Make sure to keep the
indications and notices in the operation manual.
2. USE THE DESIGNATED PARTS
The parts in this equipment have the specific
characters of incombustibility and withstand
voltage for safety. Therefore, the part which is
replaced should be used the part which has
the same character.
Especially as to the important parts for safety
which is indicated in the circuit diagram or the
table of parts as a
mark, the designated
parts must be used.
3. PUT PARTS AND WIRES IN THE
ORIGINAL POSITION AFTER
ASSEMBLING OR WIRING
There are parts which use the insulation
material such as a tube or tape for safety, or
which are assembled in the condition that
these do not contact with the printed board.
The inside wiring is designed not to get closer
to the pyrogenic parts and high voltage parts.
Therefore, put these parts in the original
positions.
4. PERFORM A SAFETY CHECK AFTER
SERVICING
Confirm that the screws, parts and wiring which
were removed in order to service are put in the
original positions, or whether there are the
portions which are deteriorated around the
serviced places serviced or not. Check the
insulation between the antenna terminal or
external metal and the AC cord plug blades.
And be sure the safety of that.
HOW TO ORDER PARTS
Please include the following informations when you order parts. (Particularly the VERSION LETTER.)
1. MODEL NUMBER and VERSION LETTER
The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be
found at the end of the SERIAL NUMBER.
2. PART NO. and DESCRIPTION
You can find it in your SERVICE MANUAL.
A1-1
TAPE REMOVAL METHOD AT NO POWER SUPPLY
1. Remove the Top Cabinet, Front Cabinet and DVD Block and the Fig. 1 below can be seen.
(Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)
2. Remove one screw of the Loading Motor from the insert hole for screw driver and remove the Loading
Motor.
3. Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.
(Refer to Fig. 2)
4. Rotate the Clutch Ass'y either of the directions to wind the Video Tape in the Cassette Case.
5. Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not to
scratch on the tape.
Loading Motor
Screw
Capstan DD Unit
Pinch Roller Cam
Main Cam
Insert hole for screw driver
Clutch Ass'y
Main Chassis (Front Side)
Fig. 1
Fig. 2
DISC REMOVAL METHOD AT NO POWER SUPPLY
1. Remove the Top Cabinet and Front Cabinet. (Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)
2. Rotate the gear of Deck CD section in the direction of the arrow by hand, remove the disc from Deck
CD. (Refer to Fig. 3)
Gear
Deck CD
Fig. 3
PARENTAL CONTROL - RATING LEVEL
4-DIGIT SECURITY CODE CANCELLATION
If the stored 4-digit security code in the Rating Level menu needs to be cancelled, please follow the steps below.
1. Connect the set to TV Monitor.
2. Turn on the power, and set to the DVD stop mode.
3. Press the SET UP button to display the DVD menu.
4. Press the SET +/- button to select the "Operation" menu.
5. Press the CH UP/DOWN button to select the Parental Lock, then press the ENTER button.
6. Press the CH UP/DOWN button to select the ON or OFF, then press the ENTER button.
7. Press the STOP button four times on the remote control, then press the ENTER button.
The 4-digit security code is cleared.
8. Press the SET UP button to disappear the DVD menu.
A1-2
CONTENTS
• OWNER'S MANUAL
IMPORTANT WARNING ............................................................................................................
SERVICING NOTICES ON CHECKING ....................................................................................
HOW TO ORDER PARTS ..........................................................................................................
TAPE REMOVAL METHOD AT NO POWER SUPPLY ............................................................
DISC REMOVAL METHOD AT NO POWER SUPPLY .............................................................
PARENTAL CONTROL-RATING LEVEL ..................................................................................
CONTENTS .................................................................................................................................
GENERAL SPECIFICATIONS ...................................................................................................
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS ............................................
2. REMOVAL OF VCR DECK PARTS ...................................................................................
3. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ...............................................
KEY TO ABBREVIATIONS ........................................................................................................
SERVICE MODE LIST ................................................................................................................
PREVENTIVE CHECKS AND SERVICE INTERVALS ..............................................................
RE-WRITE FOR DVD FIRMWARE ............................................................................................
WHEN REPLACING EEPROM (MEMORY) IC ..........................................................................
SERVICING FIXTURES AND TOOLS .......................................................................................
PREPARATION FOR SERVICING .............................................................................................
MECHANICAL ADJUSTMENTS ................................................................................................
ELECTRICAL ADJUSTMENTS ..................................................................................................
TROUBLESHOOTING GUIDE ...................................................................................................
BLOCK DIAGRAMS
DVD ..........................................................................................................................................
Y/C/AUDIO/HEAD AMP ..........................................................................................................
MICON .....................................................................................................................................
REGULATOR ...........................................................................................................................
OPERATION/DISPLAY ...........................................................................................................
TUNER/JACK/Hi-Fi/21PIN/OSD .............................................................................................
DVD IN/OUT ............................................................................................................................
POWER ...................................................................................................................................
SUB MICON/OSD/VPS ...........................................................................................................
PRINTED CIRCUIT BOARDS
DVD ..........................................................................................................................................
VCR .........................................................................................................................................
DISPLAY/OPERATION1/OPERATION2 ................................................................................
POWER ..................................................................................................................................
SCHEMATIC DIAGRAMS
READ CHANNEL ....................................................................................................................
DSP .........................................................................................................................................
MPEG ......................................................................................................................................
MEMORY ................................................................................................................................
AUDIO/VIDEO ........................................................................................................................
SYSCON 1 ..............................................................................................................................
Y/C/AUDIO/HEAD AMP ..........................................................................................................
VCR SYSCON .........................................................................................................................
TUNER/JACK ..........................................................................................................................
REGULATOR ...........................................................................................................................
OPERATION/DISPLAY ...........................................................................................................
Hi-Fi/DEMODULATOR ............................................................................................................
DVD IN/OUT ............................................................................................................................
SUB MICON/OSD/VPS ...........................................................................................................
POWER ...................................................................................................................................
DISPLAY ..................................................................................................................................
OPERATION ............................................................................................................................
INTERCONNECTION DIAGRAM ...............................................................................................
WAVEFORMS .............................................................................................................................
MECHANICAL EXPLODED VIEW .............................................................................................
PACKING DIAGRAM ..................................................................................................................
CHASSIS EXPLODED VIEWS ...................................................................................................
REPLACEMENT PARTS LIST ...................................................................................................
A2-1
A1-1
A1-1
A1-1
A1-2
A1-2
A1-2
A2-1
A3-1~A3-19
B1-1, B1-2
B2-1~B2-6
B3-1, B3-2
C1-1, C1-2
C2-1
C3-1, C3-2
C4-1
C4-2
D1-1
D1-1
D2-1~D2-4
D3-1, D3-2
E-1~E-35
F-1, F-2
F-3~F-8
F-9~F-12
F-13~F-16
F-17, F-18
F-19~F-24
F-25~F-28
F-29~F-32
F-33~F-36
G-1,G-2
G-3~G-14
G-15, G-16
G-17, G-18
H-1, H-2
H-3, H-4
H-5, H-6
H-7, H-8
H-9, H-10
H-11, H-12
H-13~H-18
H-19~H-24
H-25~H-30
H-31~H-36
H-37, H-38
H-39, H-40
H-41~H-44
H-45~H-48
H-49~H-52
H-53, H-54
H-55, H-56
H-57~H-60
I-1~I-3
J1-1
J2-1, J2-2
J3-1, J3-2
K1-1~K1-8
GENERAL SPECIFICATIONS
(SD-22VB)
G-1
G-2
Outline of the product
DVD System
Color System
Disc
Disc Diameter
Deck
Video Head
DVD VIDEO PLAYER & VHS Player / Recorder
PAL
DVD, CD-DA, CD-R/RW, VIDEO CD
120 mm , 80 mm
Front Disc Loading
3 Motors
1-Lens 2-Beams System
135min (4.7GB)
245min (8.5GB)
74min
74min
Fwd
2-100 times / 4 steps (DVD)
4-8 times / 2 steps (CD)
5-15 times / 2 steps (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Rev
2-100 times / 4 steps (DVD)
4-8 times / 2 steps (CD)
5-15 times / 2 steps (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Fwd
1/8-1/2 times (DVD, VIDEO CD)
1/7-1/2 times (DVD, VIDEO CD)
Rev
--VHS Player / Recorder
PAL
Yes
Yes
OVD-7
Front
3
4Head
FM Audio Head
2Head
Disc Loading System
Motor
Pick up
Playback time (Max)
DVD 1-Layer
DVD 2-Layer
CD
VIDEO CD
Search speed
Actual
Actual
Slow speed
Actual
Actual
G-3
VCR
System
System
Video System
Hi-Fi STEREO
NTSC PB(PAL60Hz)
Deck
Heads
DECK
Loading System
Motor
Audio /Control
Erase(Full Track Erase)
Tape
Rec
PAL
Speed
NTSC
Play
PAL
NTSC
Fast Forward / Rewind Time (Approx.) at 25oC
with Cassette
G-4
Tuning
System
Forward/Reverse
Picture Search
Frame Advance
Slow Speed
Broadcasting System
Tuner and
Receive CH
NTSC or PAL-M
PAL or SECAM
System
Destination
Tuning System
Input Impedance
CH Coverage
Intermediate
Frequency
G-5
Power
G-6
Regulation
G-7
Temperature
G-8
Operating Humidity
Picture(FP)
Sound(FS)
FP-FS
Preset CH
RF Converter Output
Channel
Level/Impedance
Sound Selector
Stereo/Dual TV Sound
Tuner Sound Muting
Power Source
AC
DC
Power Consumption
Stand by
Per Year
Protector
Power Fuse
Safety
Radiation
Operation
Storage
A3-1
Mono/Yes
Yes
SP/LP
SP/LP
SP
FF:1'48"/REW:1'48"
E-180
SP=3x, 5x
SP/LP=5x, 7x / 7x, 13x
1/10
1/5, 1/10,1/30
U.K./I.R. System I/I
1Tuner
I.R. + CCIR Hyper
F-Synth
VHF/UHF 75 OHM
IreE2~E4,X~Z+2,S1~S10,E5~E12,
S11~S41,E21~E69
39.5MHz
33.5MHz
6.0MHz
80CH
Yes
23~69 CH
73 dBu / 75 Ohm
No
NICAM
Yes
230~240V 50Hz
23 W at 230V 50Hz
7 W at 230V 50Hz
-- W
Yes
BEAB
CE
5oC - 40oC
-20oC - 60oC
Less than 80% RH
GENERAL SPECIFICATIONS
(SD-22VB)
G-9
Signal
G-10 On Screen
Display
Video Signal
Output Level
S/N Ratio (Weighted)
Horizontal Resolution
RGB Signal
Output Level
Audio Signal
Input Level Microphone
Input Level Line
(0dB=0.775Vrms) Output Level Line
Digital Output Level
S/N Ratio at (Weighted)
Harmonic Distortion (1KHz)
Typical
Frequency Response : DVD Mode at DVD
DVD Mode at VIDEO CD
DVD Mode at CD
VCR Mode at SP
VCR Mode at LP
VCR Mode at SLP
Hi-Fi Audio Signal
Dynamic Range : More than
Frequency Response
Wow And Flutter : Less than
Channel Separation : More than
Harmonic Distortion : Less than
Menu
(DVD)
Menu Type
Picture
TV Shape
PAL/Auto
Video Out Select
Output Sound
Audio Out Select
Dynamic Range Control
Karaoke Vocal
Language
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
Display
On-Screen Displays
Background
Screen Saver
Operational
Pause/Still
Parental Lock
Title Stop
PBC
Initial Setup
On-Screen Displays
TV Shape
Audio Out Select
Open
Close
No disc
Reading
Play
Still/Pause
Stop
Prohibit Mark
Step
Skip+
SkipRandom
Repeat
A-B Repeat
Slow+ ##
Slow- ##
Search+ ##
Search- ##
Resume
Title No.
Chapter No.
Track No.
Time
Sub Title No.
Angle No.
Audio No.
Zoom
Enter
Exit
Bit Rate
Memory
Screen Saver
E.A.M
A3-2
1 V p-p/75 ohm (DVD,VCR)
65 dB(DVD)
53 dB(VCR)
500 Lines (DVD)
240 Lines(VCR at SP)
0.7V p-p / 75 ohm
-3.8 dBm/ 50k ohm(VCR)
-3.8 dBm/ 1k ohm(DVD,VCR)
0.5 V p-p / 75 ohm(DVD)
90dB(DVD)
42dB(VCR at SP)
0.1% (DVD)
1.5% (VCR at SP)
4 Hz - 22 KHz
4 Hz - 20 KHz
4 Hz - 20 KHz
100Hz - 10 KHz
100Hz - 5 KHz
75dB
20Hz ~20kHz
0.01 %Wrms
60 dB
0.01
Yes
Icon
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VB)
On Screen
Display(VCR)
G-11 OSD Language
G-12 Clock,Timer
and Timer
Back-up
Menu
Menu
Type
ATS
Timer Rec Set
VCR Extension
Auto Repeat On/Off
Scene Repeat
Audio Dubbing
VCR Set-Up
NICAM Auto/Off
Audio Mix On/Off
Color System
Sharpness
BBE On/Off
CH Set-Up
CH Tuning
Auto Tuning
CH Mapping
Guide CH Set
Pin Code Registration
System Set-Up
Clock Set
Language
AV2 DEC/AV
G-CODE(or SHOWVIEW or PLUSCODE)No. Entry
NICAM 1/2,NICAM Off,Audio Output
Stereo,Audio Output,Bilingual
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark)
CH/AV
Others
Clock/Date
Repeat
Pin Code
Tape Counter
Index
Hotel Lock
Tape Speed
Manual Tracking (Bar Setting)
Hi-Fi
S-Repeat/SR-R/SR-Play
VPS
PDC
TEST Signal
DVD OSD
VCR OSD
Calendar
Timer Events
One Touch Recording Max Time
OTPB Valid Time
Timer Back-up (at Power Off Mode)
A3-3
Yes
Character
No
Yes
No
Yes
No
No
Yes
Yes
Yes
No
Yes
No
Yes
Yes
No
No
Yes
No
Yes
Yes
Yes
(Calendar 24H)
No
Yes
Yes
No
Yes
Yes
Yes
No
No
Yes
Yes
No
Yes
Yes
Yes
No
No
Yes
Yes
Eng Ger Fre
Eng Ger Fre
1990/1/1 ~ 2081/12/31
8 Program/ 1 Month
SP:5Hours
LP:10 Hours
No
30
Min
GENERAL SPECIFICATIONS
(SD-22VB)
G-13 Display
DISPLAY
DISPLAY type
Clock/Counter,CH,Timer Rec,OTR, Play
Rec,FF(Cue),Rew(Rev),Stop,ATR,Eject
VCR
DVD
CD
Clock
AM
PM
Counter
VCR
DVD
CD
Counter Remain
Play
Stop
Rec
FF / Cue
REW /Review
Pause/Still
OTR
T-Rec
Chapter
TITLE
TRACK
Repeat
Hi-Fi
SP
LP
SLP(EP)
CH
RF Output CH
Auto Tuning
Eject
Tape In
PBC(Play Back Control)
A3-4
Yes
Fluorescent Indicator
No
Yes
No
No
Yes (24h)
No
No
Yes (hour:min:sec)
Yes (hour:min:sec)
Yes (min:sec)
No
Yes
No
Yes
No
No
No
No
Yes
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VB)
G-14 Remote
Control
Unit
Glow in Dark Remocon
Power Source
Total Keys
Keys
Voltage(D.C)
UM size x pcs
Power
VCR
DVD
1
2
3
4
5
6
7
8
9
0/AV
DVD MENU
MEMORY
RETURN
OPEN/CLOSE
CLOCK / COUNTER
SUB TITLE/ATR
ANGLE/COUNTER RESET
ZERO RETURN
PLAY MODE/SPEED
ZOOM
TITLE
REPEAT A-B
PROGRAM/G-CODE
T-REC
TV/VCR
FF(Cue)/SEARCH+
REW(Review)/SEARCHPLAY
STOP
PAUSE/STILL
REC/OTR
SKIP+ / INDEX+
SKIP- / INDEXUP/CH+
DOWN/CHLEFT/ SET- / TRACKINGRIGHT/ SET+ / TRACKING+
SELECT/ENTER
SET UP MENU/ VCR MENU
CLEAR/CANCEL
DISPLAY/CALL
AUDIO / AUDIO SELECT
SLOW(Forward)
E.A.M.
CM SKIP(Skip search)
REC END SEARCH/ONE TOUCH REPLAY
A3-5
RC-FW
Yes
3V
UM-4 x 2 pcs
48 Keys
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
GENERAL SPECIFICATIONS
(SD-22VB)
G-15 Features
(DVD)
Auto Power Off
Parental Lock
Video CD Playback
MP3 Playback
Digital Out
Down Mix Out
Self Diagnostic
Features
(VCR)
G-16 Accessories
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Dolby Digital
PCM
DTS
MPEG1,MPEG2
(Dolby Digital, MPEG1,MPEG2)
No
Yes
Yes
Yes
Spatializer (N-2-2)
Screen Saver
Frame Advance
One Touch Replay (10 Sec reverse)
Auto Head Cleaning
Auto Tracking
Index Search
HQ (VHS Standard High Quality)
Auto Power On, Auto Play, Auto Rewind, Auto Eject
Auto Repeat
Auto Power Off
VIDEO PLUS+(SHOWVIEW,G-CODE)
ATS
Auto Set Up (CH Auto Set-Up/Auto Clock)
PDC
VPS
Reverse Slow
One Touch Playback
Picture Control(Sharpness)
Channel Lock
Hotel Lock
Anti Theft
Audio Dubbing
Remote Control Code 1/2
BBE Audio
Rec END Search
SQPB(PAL SP MODE)
CATV
CM Skip(30sec x 6 Times)
Owner's Manual
Language
w/Guarantee Card
Buyer Model No
Remote Control Unit
Dew Caution Sheet
Battery
UM size x pcs
Tape Rewinder
Safety Tip
Toll Free Insert Sheet
Quick Set-Up Sheet
Information Sheet
75 Ohm Coaxial Cable
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
No
No
No
Yes
No
No
No
No
No
No
No
Yes
Yes
Yes
Yes
English
No
SD-22VB
Yes
No
Yes
UM-4 x 2 pcs
No
No
No
Yes
No
type
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
AC Cord
AV Cord (2Pin-1Pin)
Registration Card
21pin Cable
300 ohm to 75 ohm Antenna Adapter
Yes
(0.9m)
Single shield
No
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
A3-6
GENERAL SPECIFICATIONS
(SD-22VB)
G-17 Interface
Switch
Front
Rear
Volume
Terminals
Front
Rear
Indicator
G-18 Set Size
G-19 Weight
G-20 Carton
Power
Play
Eject (VCR)
Stop
Rec/OTR
Open/Close (DVD)
CH +
CH FF/ Search(>>)
Rew/Search(<<)
Still/Pause
Shuttle(Search/REV/FWD)
DVD/VCR
Input Select
Main Power SW
Attenuator
Video/RGB Selector
RF Out(Slide SW)
Main Power SW
Phones Volume
Mic Volume
Echo Volume
Rec/OTR
Video In
Audio In
Video Output
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Audio Output
Video Input
RCA x 2(Stereo, White/Red)
Coaxial x 1 (Digital Audio,DVD Signal Only)
No
Audio Input
No
Optical Digital Audio Out (Option)
Euro Scart
S-Video Output
Ext Speaker
VHF/UHF Antenna Input/Output
AC Inlet
LED
Power
Rec
T-Rec
TV/VCR
DVD
VCR
Surround
Level Meter
Approx.
W x D x H (mm)
Net (Approx.)
Gross (Approx.)
Master Carton
Content
Material
Dimensions
W x D x H(mm)
Description of Origin
Gift Box
Material
W/Color Photo Label
Dimensions
W x D x H(mm)
Pulp Package
Design
Description of Origin
Buyer Model No
Drop Test
G-21 Cabinet Material
Height (cm)
Container Stuffing
Cabinet Front
A3-7
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
RCA x1(Black)
RCA x 2(Stereo, Black)
No
Yes
2SCART
Yes (DVD Signal Only)
No
DIN Type
No
No
No
No
No
Yes (GREEN)
Yes (GREEN)
No
No
430 x 314.5 x 99
4.5 kg( 9.9lbs)
5.5 kg( 12.1lbs)
No
--- Sets
--- / ------Yes
Single Full Color Carton
No
500 x 430 x 180
No
As Per BUYER 's
Yes
SD-22VB
Natural Dropping At 1 Corner / 3 Edges / 6
Surfaces
80 cm
1,623 Sets/40' container
PS 94HB
GENERAL SPECIFICATIONS
(SD-22VE)
G-1
G-2
Outline of the product
DVD System
Color System
Disc
Disc Diameter
Deck
Video Head
DVD VIDEO PLAYER & VHS Player / Recorder
PAL
DVD, CD-DA, CD-R/RW, VIDEO CD
120 mm , 80 mm
Front Disc Loading
3 Motors
1-Lens 2-Beams System
135min (4.7GB)
245min (8.5GB)
74min
74min
Fwd
2-100 times / 4 step (DVD)
4-8 times / 2 step (CD)
5-15 times / 2 step (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Rev
2-100 times / 4 step (DVD)
4-8 times / 2 step (CD)
5-15 times / 2 step (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Fwd
1/8-1/2 times (DVD, VIDEO CD)
1/7-1/2 times (DVD, VIDEO CD)
Rev
--VHS Player / Recorder
PAL/SECAM/MESECAM
Yes
Yes
OVD-7
Front
3
4Head
FM Audio Head
2Head
Disc Loading System
Motor
Pick up
Playback time (Max)
DVD 1-Layer
DVD 2-Layer
CD
VIDEO CD
Search speed
Actual
Actual
Slow speed
Actual
Actual
G-3
VCR
System
System
Video System
Hi-Fi STEREO
NTSC PB(PAL60Hz)
Deck
Heads
DECK
Loading System
Motor
Audio /Control
Erase(Full Track Erase)
Tape
Rec
PAL
Speed
NTSC
Play
PAL
NTSC
Fast Forward / Rewind Time (Approx.) at 25oC
with Cassette
G-4
Tuning
System
Forward/Reverse
Picture Search
Frame Advance
Slow Speed
Broadcasting System
Tuner and
Receive CH
NTSC or PAL-M
PAL or SECAM
System
Destination
Tuning System
Input Impedance
CH Coverage
(SECAM)
(PAL)
G-5
Power
G-6
Regulation
G-7
Temperature
Intermediate
Picture(FP)
Frequency
Sound(FS)
FP-FS
Preset CH
RF Converter Output
Channel
Level/Impedance
Sound Selector
Stereo/Dual TV Sound
Tuner Sound Muting
Power Source
AC
DC
Power Consumption
Stand by
Per Year
Protector
Power Fuse
Safety
Radiation
Operation
Storage
A3-8
Mono/Yes
Yes
SP/LP
SP/LP
SP
FF:1'12"/REW:1'12"
E-180
SP=3x, 5x
SP/LP=5x, 7x / 7x, 13x
1/10
1/5, 1/10,1/30
CCIR,FRENCH System BG,L
1Tuner
Oscar(W/HYPER), France CATV
F-Synth
VHF/UHF 75 OHM
F2~F4, FB~FQ, F21~F69
E2~E4, X~Z+2, S1~S10,
E5~E12,S11~S41,E21~E69
PAL/SECAM(U&VH)/SECAM(VL)
38.9 / 38.9 / 34.4MHz
33.4 / 32.4 / 40.9MHz
5.5 / 6.5 / 6.5MHz
80CH
No
No
G.ST/NICAM DUAL
Yes
230V 50Hz
23 W at 230V 50Hz
7 W at 230V 50Hz
-- W
Yes
CE
CE
5oC - 40oC
-20oC - 60oC
GENERAL SPECIFICATIONS
(SD-22VE)
G-8
G-9
Operating Humidity
Signal
Video Signal
G-10 On Screen
Display
Output Level
S/N Ratio (Weighted)
Horizontal Resolution
RGB Signal
Output Level
Audio Signal
Input Level Microphone
Input Level Line
(0dB=0.775Vrms) Output Level Line
Digital Output Level
S/N Ratio at (Weighted)
Harmonic Distortion (1KHz)
Typical
Frequency Response : DVD Mode at DVD
DVD Mode at VIDEO CD
DVD Mode at CD
VCR Mode at SP
VCR Mode at LP
VCR Mode at SLP
Hi-Fi Audio Signal
Dynamic Range : More than
Frequency Response
Wow And Flutter : Less than
Channel Separation : More than
Harmonic Distortion : Less than
Menu
(DVD)
Menu Type
Picture
TV Shape
PAL/Auto
Video Out Select
Output Sound
Audio Out Select
Dynamic Range Control
Karaoke Vocal
Language
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
Display
On-Screen Displays
Background
Screen Saver
Operational
Pause/Still
Parental Lock
Title Stop
PBC
Initial Setup
On-Screen Displays
TV Shape
Audio Out Select
Open
Close
No disc
Reading
Play
Still/Pause
Stop
Prohibit Mark
Step
Skip+
SkipRandom
Repeat
A-B Repeat
Slow+ ##
Slow- ##
Search+ ##
Search- ##
Resume
Title No.
Chapter No.
Track No.
Time
Sub Title No.
Angle No.
Audio No.
Zoom
Enter
Exit
Bit Rate
Memory
Screen Saver
E.A.M
A3-9
Less then 80% RH
1 V p-p/75 ohm (DVD,VCR)
65 dB(DVD)
53 dB(VCR)
500 Lines (DVD)
240 Lines(VCR at SP)
0.7V p-p / 75 ohm
-3.8 dBm/ 50k ohm(VCR)
-3.8 dBm/ 1k ohm(DVD,VCR)
0.5 V p-p / 75 ohm(DVD)
90dB(DVD)
42dB(VCR at SP)
0.1% (DVD)
1.5% (VCR at SP)
4 Hz - 22 KHz
4 Hz - 20 KHz
4 Hz - 20 KHz
100Hz - 10 KHz
100Hz - 5 KHz
75dB
20Hz ~20kHz
0.01 %Wrms
60 dB
0.01
Yes
Icon
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VE)
On Screen
Display(VCR)
G-11 OSD Language
G-12 Clock,Timer
and Timer
Back-up
G-13 Display
Menu
Menu
Type
ATS
Timer Rec Set
VCR Extension
Auto Repeat On/Off
Scene Repeat
Audio Dubbing
VCR Set-Up
NICAM Auto/Off
Audio Mix On/Off
Color System
Sharpness
BBE On/Off
CH Set-Up
CH Tuning
Auto Tuning
CH Mapping
Guide CH Set
Pin Code Registration
System Set-Up
Clock Set
Language
AV2 DEC/AV
G-CODE(or SHOWVIEW or PLUSCODE)No. Entry
NICAM 1/2,NICAM Off,Audio Output
Stereo,Audio Output,Bilingual
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark)
CH/AV
Others
Clock/Date
Repeat
Pin Code
Tape Counter
Index
Hotel Lock
Tape Speed
Manual Tracking (Bar Setting)
Hi-Fi
S-Repeat/SR-R/SR-Play
VPS
PDC
TEST Signal
DVD OSD
VCR OSD
Calendar
Timer Events
One Touch Recording Max Time
OTPB Valid Time
Timer Back-up (at Power Off Mode)
DISPLAY
DISPLAY type
Clock/Counter,CH,Timer Rec,OTR, Play
Rec,FF(Cue),Rew(Rev),Stop,ATR,Eject
VCR
DVD
CD
Clock
AM
PM
Counter
VCR
DVD
CD
Counter Remain
Play
Stop
Rec
FF / Cue
REW /Review
Pause/Still
OTR
T-Rec
Chapter
TITLE
TRACK
Repeat
Hi-Fi
SP
LP
SLP(EP)
CH
RF Output CH
Auto Tuning
Eject
Tape In
PBC(Play Back Control)
A3-10
Yes
Character
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(Calendar 24H)
No
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Eng Ger Fre
Eng Ger Fre
1990/1/1 ~ 2081/12/31
8 Program/ 1 Month
SP:5Hours
LP:10 Hours
30
Yes
Fluorescent Indicator
No
Min
No
Yes
No
No
Yes (24h)
No
No
Yes (hour:min:sec)
Yes (hour:min:sec)
Yes (min:sec)
No
Yes
No
Yes
No
No
No
No
Yes
No
No
Yes
No
No
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VE)
G-14 Remote
Control
Unit
Glow in Dark Remocon
Power Source
Total Keys
Keys
Voltage(D.C)
UM size x pcs
Power
VCR
DVD
1
2
3
4
5
6
7
8
9
0/AV
DVD MENU
MEMORY
RETURN
OPEN/CLOSE
CLOCK / COUNTER
SUB TITLE/ATR
ANGLE/COUNTER RESET
ZERO RETURN
PLAY MODE/SPEED
ZOOM
TITLE
REPEAT A-B
PROGRAM/G-CODE
T-REC
TV/VCR
FF(Cue)/SEARCH+
REW(Review)/SEARCHPLAY
STOP
PAUSE/STILL
REC/OTR
SKIP+ / INDEX+
SKIP- / INDEXUP/CH+
DOWN/CHLEFT/ SET- / TRACKINGRIGHT/ SET+ / TRACKING+
SELECT/ENTER
SET UP MENU/ VCR MENU
CLEAR/CANCEL
DISPLAY/CALL
AUDIO / AUDIO SELECT
SLOW(Forward)
E.A.M.
CM SKIP(Skip search)
REC END SEARCH/ONE TOUCH REPLAY
A3-11
RC-FW
Yes
3V
UM-4 x 2 pcs
48 Key
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
GENERAL SPECIFICATIONS
(SD-22VE)
G-15 Features
(DVD)
Auto Power Off
Parental Lock
Video CD Playback
MP3 Playback
Digital Out
Down Mix Out
Self Diagnostic
Features
(VCR)
G-16 Accessories
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Dolby Digital
PCM
DTS
MPEG1,MPEG2
(Dolby Digital, MPEG1,MPEG2)
No
Yes
Yes
Yes
Spatializer (N-2-2)
Screen Saver
Frame Advance
One Touch Replay (10 Sec reverse)
Auto Head Cleaning
Auto Tracking
Index Search
HQ (VHS Standard High Quality)
Auto Power On, Auto Play, Auto Rewind, Auto Eject
Auto Repeat
Auto Power Off
VIDEO PLUS+(SHOWVIEW,G-CODE)
Auto Tuning/Auto Clock/Auto Guide ch
Auto Set Up (CH Auto Set-Up/Auto Clock)
PDC
VPS
Reverse Slow
One Touch Playback
Picture Control(Sharpness)
Channel Lock
Hotel Lock
Anti Theft
Audio Dubbing
Remote Control Code 1/2
BBE Audio
Rec END Search
SQPB(PAL SP MODE)
CATV
CM Skip(30sec x 6 Times)
Copy Disc to Tape
Owner's Manual
Language
w/Guarantee Card
Buyer Model No
Remote Control Unit
Dew Cation Sheet
Battery
UM size x pcs
Tape Rewinder
Safety Tip
Toll Free Insert Sheet
Quick Set-Up Sheet
Information Sheet
75 Ohm Coaxial Cable
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
No
Yes
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes (by Conditioning)
Yes
French/ German
No
SD-22VE
Yes
No
Yes
UM-4 x 2 pcs
No
No
No
Yes(English)
No
type
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Warning Sheet
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
AC Cord
AV Cord (2Pin-1Pin)
Registration Card
21pin Cable(Double Shield)
300 ohm to 75 ohm Antenna Adapter
Yes
(0.9m)
Single shield
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
A3-12
GENERAL SPECIFICATIONS
(SD-22VE)
G-17 Interface
Switch
Front
Rear
Volume
Terminals
Front
Rear
Power
Play
Eject (VCR)
Stop
Rec/OTR
Open/Close (DVD)
CH +
CH FF/ Search(>>)
Rew/Search(<<)
Still/Pause
Shuttle(Search/REV/FWD)
DVD/VCR
Input Select
Main Power SW
Attenuator
Video/RGB Selector
RF Out(Slide SW)
Main Power SW
Phones Volume
Mic Volume
Echo Volume
Rec/OTR
Video In
Audio In
Video Output
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Audio Output
RCA x 2(Stereo, White/Red)
Coaxial x 1 (Digital Audio,DVD Signal Only)
No
Video Input
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
RCA x1(Black)
RCA x 2(Stereo, Black)
No
Audio Input
Indicator
G-18 Set Size
G-19 Weight
G-20 Carton
No
Optical Digital Audio Out (Option)
Euro Scart
S-Video Output
Ext Speaker
VHF/UHF Antenna Input/Output
AC Inlet
LED
Power
Rec
T-Rec
TV/VCR
DVD
VCR
Surround
Level Meter
Approx.
W x D x H (mm)
Net (Approx.)
Gross (Approx.)
Master Carton
Content
Material
Dimensions
W x D x H(mm)
Description of Origin
Gift Box
Material
W/Color Phote Label
Dimensions
W x D x H(mm)
Pulp Package
Design
Description of Origin
Buyer Model No
Drop Test
G-21 Cabinet Material
Height (cm)
Container Stuffing
Cabinet Front
A3-13
Yes
2SCART
Yes (DVD Signal Only)
No
DIN Type (France)
No
No
No
No
No
Yes (GREEN)
Yes (GREEN)
No
No
430 x 314.5 x 99
4.5 kg( 9.9lbs)
5.5 kg( 12.1lbs)
No
--- Sets
--- / ------Yes
Single Full Color Carton
No
500 x 430 x 180
No
As Per BUYER 's
Yes
SD-22VE
Natural Dropping At 1 Corner / 3 Edges / 6
Surfaces
80 cm
1,623 Sets/40' container
PS 94HB
GENERAL SPECIFICATIONS
(SD-22VL)
G-1
G-2
Outline of the product
DVD System
Color System
Disc
Disc Diameter
Deck
Video Head
DVD VIDEO PLAYER & VHS Player / Recorder
PAL
DVD, CD-DA, CD-R/RW, VIDEO CD
120 mm , 80 mm
Front Disc Loading
3 Motors
1-Lens 2-Beams System
135min (4.7GB)
245min (8.5GB)
74min
74min
Fwd
2-100 times / 4 step (DVD)
4-8 times / 2 step (CD)
5-15 times / 2 step (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Rev
2-100 times / 4 step (DVD)
4-8 times / 2 step (CD)
5-15 times / 2 step (VIDEO CD)
2-70 times (DVD)
4-12times (CD)
4-18times (VIDEO CD)
Fwd
1/8-1/2 times (DVD, VIDEO CD)
1/7-1/2 times (DVD, VIDEO CD)
Rev
--VHS Player / Recorder
PAL
Yes
Yes
OVD-7
Front
3
4Head
FM Audio Head
2Head
Disc Loading System
Motor
Pick up
Playback time (Max)
DVD 1-Layer
DVD 2-Layer
CD
VIDEO CD
Search speed
Actual
Actual
Slow speed
Actual
Actual
G-3
VCR
System
System
Video System
Hi-Fi STEREO
NTSC PB(PAL60Hz)
Deck
Heads
DECK
Loading System
Motor
Audio /Control
Erase(Full Track Erase)
Tape
Rec
PAL
Speed
NTSC
Play
PAL
NTSC
Fast Forward / Rewind Time (Approx.) at 25oC
with Cassette
G-4
Tuning
System
Forward/Reverse
Picture Search
Frame Advance
Slow Speed
Broadcasting System
Tuner and
Receive CH
NTSC or PAL-M
PAL or SECAM
System
Destination
Tuning System
Input Impedance
CH Coverage
Intermediate
Frequency
G-5
Power
G-6
Regulation
G-7
Temperature
Picture(FP)
Sound(FS)
FP-FS
Preset CH
RF Converter Output
Channel
Level/Impedance
Sound Selector
Stereo/Dual TV Sound
Tuner Sound Muting
Power Source
AC
DC
Power Consumption
Stand by
Per Year
Protector
Power Fuse
Safety
Radiation
Operation
Storage
A3-14
Mono/Yes
Yes
SP/LP
SP/LP
SP
FF:1'12"/REW:1'12"
E-180
SP=3x, 5x
SP/LP=5x, 7x / 7x, 13x
1/10
1/5, 1/10,1/30
CCIR System BG
1Tuner
Oscar(W/HYPER)
F-Synth
VHF/UHF 75 OHM
E2~E4, X~Z+2, S1~S10,
E5~E12,S11~S41,E21~E69
38.9 MHz
33.4 MHz
5.5 MHz
80CH
Yes
23~69 CH
73 dBu / 75 Ohm
No
G.ST/NICAM DUAL
Yes
230V 50Hz
23 W at 230V 50Hz
7 W at 230V 50Hz
-- W
Yes
CE
CE
5oC - 40oC
-20oC - 60oC
GENERAL SPECIFICATIONS
(SD-22VL)
G-8
G-9
Operating Humidity
Signal
G-10
On Screen
Display
Video Signal
Output Level
S/N Ratio (Weighted)
Horizontal Resolution
RGB Signal
Output Level
Audio Signal
Input Level Microphone
Input Level Line
(0dB=0.775Vrms) Output Level Line
Digital Output Level
S/N Ratio at (Weighted)
Harmonic Distortion (1KHz)
Typical
Frequency Response : DVD Mode at DVD
DVD Mode at VIDEO CD
DVD Mode at CD
VCR Mode at SP
VCR Mode at LP
VCR Mode at SLP
Hi-Fi Audio Signal
Dynamic Range : More than
Frequency Response
Wow And Flutter : Less than
Channel Separation : More than
Harmonic Distortion : Less than
Menu
(DVD)
Menu Type
Picture
TV Shape
PAL/Auto
Video Out Select
Output Sound
Audio Out Select
Dynamic Range Control
Karaoke Vocal
Language
On-Screen Language
Disc Menu Language
Audio Language
Subtitle Language
Display
On-Screen Displays
Background
Screen Saver
Operational
Pause/Still
Parental Lock
Title Stop
PBC
Initial Setup
On-Screen Displays
TV Shape
Audio Out Select
Open
Close
No disc
Reading
Play
Still/Pause
Stop
Prohibit Mark
Step
Skip+
SkipRandom
Repeat
A-B Repeat
Slow+ ##
Slow- ##
Search+ ##
Search- ##
Resume
Title No.
Chapter No.
Track No.
Time
Sub Title No.
Angle No.
Audio No.
Zoom
Enter
Exit
Bit Rate
Memory
Screen Saver
E.A.M
A3-15
Less than 80% RH
1 V p-p/75 ohm (DVD,VCR)
65 dB(DVD)
53 dB(VCR)
500 Lines (DVD)
240 Lines(VCR at SP)
0.7V p-p / 75 ohm
-3.8 dBm/ 50k ohm(VCR)
-3.8 dBm/ 1k ohm(DVD,VCR)
0.5 V p-p / 75 ohm(DVD)
90dB(DVD)
42dB(VCR at SP)
0.1% (DVD)
1.5% (VCR at SP)
4 Hz - 22 KHz
4 Hz - 20 KHz
4 Hz - 20 KHz
100Hz - 10 KHz
100Hz - 5 KHz
75dB
20Hz ~20kHz
0.01 %Wrms
60 dB
0.01
Yes
Icon
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VL)
On Screen
Display(VCR)
G-11
OSD Language
G-12
Clock,Timer
and Timer
Back-up
G-13
Display
Menu
Menu
Type
ATS
Timer Rec Set
VCR Extension
Auto Repeat On/Off
Scene Repeat
Audio Dubbing
VCR Set-Up
NICAM Auto/Off
Audio Mix On/Off
Color System
Sharpness
BBE On/Off
CH Set-Up
CH Tuning
Auto Tuning
CH Mapping
Guide CH Set
Pin Code Registration
System Set-Up
Clock Set
Language
AV2 DEC/AV
G-CODE(or SHOWVIEW or PLUSCODE)No. Entry
NICAM 1/2,NICAM Off,Audio Output
Stereo,Audio Output,Bilingual
Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark)
CH/AV
Others
Clock/Date
Repeat
Pin Code
Tape Counter
Index
Hotel Lock
Tape Speed
Manual Tracking (Bar Setting)
Hi-Fi
S-Repeat/SR-R/SR-Play
VPS
PDC
TEST Signal
DVD OSD
VCR OSD
Calendar
Timer Events
One Touch Recording Max Time
OTPB Valid Time
Timer Back-up (at Power Off Mode)
DISPLAY
DISPLAY type
Clock/Counter,CH,Timer Rec,OTR, Play
Rec,FF(Cue),Rew(Rev),Stop,ATR,Eject
VCR
DVD
CD
Clock
AM
PM
Counter
VCR
DVD
CD
Counter Remain
Play
Stop
Rec
FF / Cue
REW /Review
Pause/Still
OTR
T-Rec
Chapter
TITLE
TRACK
Repeat
Hi-Fi
SP
LP
SLP(EP)
CH
RF Output CH
Auto Tuning
Eject
Tape In
PBC(Play Back Control)
A3-16
Yes
Character
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
Yes
Yes
Yes
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
(Calendar 24H)
No
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Ger Spa Ita
Ger Spa Ita
1990/1/1 ~ 2081/12/31
8 Program/ 1 Month
SP:5Hours
LP:10 Hours
30
Yes
Fluorescent Indicator
No
Min
No
Yes
No
No
Yes (24h)
No
No
Yes (hour:min:sec)
Yes (hour:min:sec)
Yes (min:sec)
No
Yes
No
Yes
No
No
No
No
Yes
No
No
Yes
No
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
GENERAL SPECIFICATIONS
(SD-22VL)
G-14
Remote
Control
Unit
Glow in Dark Remocon
Power Source
Total Keys
Keys
Voltage(D.C)
UM size x pcs
Power
VCR
DVD
1
2
3
4
5
6
7
8
9
0/AV
DVD MENU
MEMORY
RETURN
OPEN/CLOSE
CLOCK / COUNTER
SUB TITLE/ATR
ANGLE/COUNTER RESET
ZERO RETURN
PLAY MODE/SPEED
ZOOM
TITLE
REPEAT A-B
PROGRAM/G-CODE
T-REC
TV/VCR
FF(Cue)/SEARCH+
REW(Review)/SEARCHPLAY
STOP
PAUSE/STILL
REC/OTR
SKIP+ / INDEX+
SKIP- / INDEXUP/CH+
DOWN/CHLEFT/ SET- / TRACKINGRIGHT/ SET+ / TRACKING+
SELECT/ENTER
SET UP MENU/ VCR MENU
CLEAR/CANCEL
DISPLAY/CALL
AUDIO / AUDIO SELECT
SLOW(Forward)
E.A.M.
CM SKIP(Skip search)
REC END SEARCH/ONE TOUCH REPLAY
A3-17
RC-FW
Yes
3V
UM-4 x 2 pcs
48 Keys
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
GENERAL SPECIFICATIONS
(SD-22VL)
G-15
Features
(DVD)
Auto Power Off
Parental Lock
Video CD Playback
MP3 Playback
Digital Out
Down Mix Out
Self Diagnostic
Features
(VCR)
G-16
Accessories
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Dolby Digital
PCM
DTS
MPEG1,MPEG2
(Dolby Digital, MPEG1,MPEG2)
No
Yes
Yes
Yes
Spatializer (N-2-2)
Screen Saver
Frame Advance
One Touch Replay (10 Sec reverse)
Auto Head Cleaning
Auto Tracking
Index Search
HQ (VHS Standard High Quality)
Auto Power On, Auto Play, Auto Rewind, Auto Eject
Auto Repeat
Auto Power Off
VIDEO PLUS+(SHOWVIEW,G-CODE)
Auto Tuning/Auto Clock/Auto Guide Ch
Auto Set Up (CH Auto Set-Up/Auto Clock)
PDC
VPS
Reverse Slow
One Touch Playback
Picture Control(Sharpness)
Channel Lock
Hotel Lock
Anti Theft
Audio Dubbing
Remote Control Code 1/2
BBE Audio
Rec END Search
SQPB(PAL SP MODE)
CATV
CM Skip(30sec x 6 Times)
Copy (Disc to Tape)
Owner's Manual
Language
w/Guarantee Card
Buyer Model No
Remote Control Unit
Dew Cation Sheet
Battery
UM size x pcs
Tape Rewinder
Safety Tip
Toll Free Insert Sheet
Quick Set-Up Sheet
Information Sheet
75 Ohm Coaxial Cable
No
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
Yes
No
No
Yes
No
No
No
Yes
No
No
No
Yes
Yes
Yes
Yes (by Conditioning)
Yes
German/ Italian/ Spanish
No
SD-22VL
Yes
No
Yes
UM-4 x 2 pcs
No
No
No
Yes (English)
No
type
U/V Mixer
DC Car Cord (Center+)
Guarantee Card
Service Extended Plan
Circuit Diagram
Antenna Change Plug
Service Facility List
Important Safeguard
Dew/AHC Caution Sheet
AC Plug Adapter
AC Cord
AV Cord (2Pin-1Pin)
Registration Card
21pin Cable
300 ohm to 75 ohm Antenna Adapter
Yes
(0.9m)
Single shield
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
A3-18
GENERAL SPECIFICATIONS
(SD-22VL)
G-17
Interface
Switch
Front
Rear
Volume
Terminals
Front
Rear
Power
Play
Eject (VCR)
Stop
Rec/OTR
Open/Close (DVD)
CH +
CH FF/ Search(>>)
Rew/Search(<<)
Still/Pause
Shuttle(Search/REV/FWD)
DVD/VCR
Input Select
Main Power SW
Attenuator
Video/RGB Selector
RF Out(Slide SW)
Main Power SW
Phones Volume
Mic Volume
Echo Volume
Rec/OTR
Video In
Audio In
Video Output
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Audio Output
RCA x 2(Stereo, White/Red)
Coaxial x 1 (Digital Audio,DVD Signal Only)
No
Video Input
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
RCA x1(Black)
RCA x 2(Stereo, Black)
No
Audio Input
Indicator
G-18
G-19
Set Size
Weight
G-20
Carton
Optical Digital Audio Out (Option)
Euro Scart
S-Video Output
Ext Speaker
VHF/UHF Antenna Input/Output
AC Inlet
LED
Power
Rec
T-Rec
TV/VCR
DVD
VCR
Surround
Level Meter
Approx.
W x D x H (mm)
Net (Approx.)
Gross (Approx.)
Master Carton
Content
Material
Dimensions
W x D x H(mm)
Description of Origin
Gift Box
Material
W/Color Photo Label
Dimensions
W x D x H(mm)
Pulp Package
Design
Description of Origin
Buyer Model No
Drop Test
G-21
Cabinet Material
Height (cm)
Container Stuffing
Cabinet Front
A3-19
No
Yes
2SCART
Yes (DVD Signal Only)
No
DIN Type
No
No
No
No
No
Yes (GREEN)
Yes (GREEN)
No
No
430 x 314.5 x 99
4.5 kg( 9.9lbs)
5.5 kg( 12.1lbs)
No
--- Sets
--- / ------Yes
Single Full Color Carton
No
500 x 430 x 180
No
As Per BUYER 's
Yes
SD-22VL
Natural Dropping At 1 Corner / 3 Edges / 6
Surfaces
80 cm
1,623 Sets/40' container
PS 94HB
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS
AND P.C. BOARDS
(A)
1-1: TOP CABINET AND FRONT CABINET
(Refer to Fig. 1-1)
1.
2.
3.
4.
5.
(C)
Remove the 5 screws 1.
Remove the Top Cabinet in the direction of arrow (A).
Disconnect the following connectors: (CP681, CP601).
Unlock the 8 supports 2.
Remove the Front Cabinet in the direction of arrow (B).
(B)
Flap
1
Top Cabinet
1
Fig. 1-3
1
1
1-4: DECK CD AND DVD PCB (Refer to Fig. 1-4)
1. Make the short circuit on the position as shown Fig. 1-4
using a soldering. If you remove the Deck CD with no
soldering, the Laser may be damaged.
2. Disconnect the following connectors:
(CP503,CP8001, CP8002).
3. Remove the 4 screws 1.
4. Remove the Deck Angle in the direction of arrow (A).
5. Remove the 2 screws 2.
6. Remove the Front-DVD Shield in the direction of arrow
(B).
7. Remove the 4 screws 3.
8. Disconnect the following connectors: (CP2601, CP2602
and CP2603).
9. Remove the Deck CD in the direction of arrow (C).
10. Remove the 4 screws 4.
11. Remove the DVD PCB in the direction of arrow (D).
(A)
1
Front Cabinet
2
(B)
2
2
2
2
2
2
2
Fig. 1-1
1-2: DISPLAY PCB AND OPERATION 1/2 PCB
(Refer to Fig. 1-2)
1. Remove the 11 screws 1.
2. Remove the Display PCB and Operation 1/2 PCB in the
direction of arrow.
Pick Up PCB
3
Display PCB
1
3
1
1
1
1
Deck CD
1
1
3
Operation 2 PCB
1
1
3
1
1
1
Deck Angle
(C)
Front-DVD Shield
1
Make the sort circuit
using a soldering.
1
(B)
1
(D)
Operation 1 PCB
Front Cabinet
DVD PCB
2
Fig. 1-2
2
4
4
4
1-3: FLAP (Refer to Fig. 1-3)
1. Open Flap to 90˚ and flex in direction of arrow (A), at
the same time slide in direction of arrow (B).
2. Then lift in direction of arrow (C).
4
(A)
Fig. 1-4
NOTE
When the installation of the Deck CD, remove all the
soldering on the short circuit position after the connection of
Pick Up PCB and DVD PCB connector.
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: VCR DECK (Refer to Fig. 1-5)
1-7: POWER PCB (Refer to Fig. 1-7)
1. Unlock the 2 supports 1 and remove the Top Holder.
2. Remove the 3 screws 2.
3. Disconnect the following connectors: (CP101, CP102,
CP103 and CP3001).
4. Remove the AC Head Cover and VCR Deck in the
direction of arrow.
1. Remove the 3 screws 1.
2. Remove the Power PCB in the direction of arrow.
2
1
1
1
2
Power PCB
2
AC Head Cover
Bottom Plate
VCR Deck
Top Holder
1
1
Fig. 1-7
Fig. 1-5
1-6: VCR PCB (Refer to Fig. 1-6)
1.
2.
3.
4.
Remove the screw 1 and Fiber Washer.
Remove the 5 screws 2.
Disconnect the following connector: (CP1701).
Remove the VCR PCB in the direction of arrow.
2
VCR PCB
Fiber Washer
1
2
22
2
2
Fig. 1-6
B1-2
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DECK PARTS
NOTE
2-1: TOP BRACKET (Refer to Fig. 2-1)
1. In case of the Locker R installation, check if the two
positions of Fig.2-3-B are correctly locked.
2. When you install the Cassette Side R, be sure to move
the Locker R after installing.
1. Extend the 2 supports 1.
2. Slide the 2 supports 2 and remove the Top Bracket.
NOTE
1. After the installation of the Top Bracket, bend the
support 1 so that the Top Bracket is fixed.
Locker R
Top Bracket
Check if these
positions are locked.
Cassette Side R
1
1
Top Bracket
2
Fig. 2-3-B
2
Main Chassis
2-4: LINK UNIT (Refer to Fig. 2-4)
Main Chassis
1. Set the Link Unit to the Eject position.
2. Unlock the support 1.
3. Remove the (A) side of the Link Unit first, then remove
the (B) side.
Fig. 2-1
2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2)
1. Move the Cassette Holder Ass'y to the front side.
2. Push the Locker R to remove the Cassette Side R.
3. Remove the Cassette Side L.
Main Chassis
Link Unit
Cassette Side R
Locker R
Main Chassis
(A)
(B)
Link Unit
1
Main Chassis
Fig. 2-4
Link Unit
2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5)
Main Chassis
Cassette Side L
1. Extend the support 1.
2. Remove the Link Lever.
3. Remove the Flap Lever.
Fig. 2-2
2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)
1. Remove the Locker Spring.
2. Unlock the 4 supports 1 and then remove the Cassette
Side L/R.
3. Unlock the support 2 and then remove the Locker R.
Flap Lever
Locker Spring
1
1
1
Cassette Holder
Link Lever
2
Fig. 2-5
Locker R
1
1
Cassette Side R
Cassette Side L
Fig. 2-3-A
B2-1
DISASSEMBLY INSTRUCTIONS
2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)
2-7: TENSION ASS'Y (Refer to Fig. 2-7-B)
1. Remove the screw 1.
2. Remove the Loading Motor.
3. Remove the Worm.
1. Turn the Pinch Roller Cam clockwise so that the
Tension Holder hook is set to the position of Fig. 2-7-A
to move the Tension Arm Ass'y.
2. Remove the Tension Spring.
3. Unlock the 2 supports 1 and remove the Tension
Band.
4. Unlock the support 2 and remove the Tension Arm
Ass'y.
5. Unlock the support 3 and remove the Tension
Connect.
6. Float the hook 4 and turn it clockwise then remove the
Tension Holder.
Loading Motor
Worm
Main Chassis
Tension Arm Ass'y
• Screw Torque: 3 ± 0.5kgf•cm
1
Fig. 2-6-A
Fig. 2-7-A
NOTE
1
1. In case of the Worm installation, check if the value of
the Fig. 2-6-B is correct.
2. In case of the Loading Motor installation, hook the wire
on the Cassette Opener as shown Fig. 2-6-C.
3. When installing the wires between Capstan DD Unit
and Loading Motor, connect them correctly as shown
Fig. 2-6-D.
Tension Connect
Tension Band
1
3
Tension Spring
Tension Arm Ass'y
Tension Holder
2
4
19.2 ± 0.1mm
Fig. 2-7-B
NOTE
Safety surface for pressing
of the insert.
1. In case of the Tension Band installation, note the
direction of the installation. (Refer to Fig. 2-7-C)
2. In case of the Tension Band installation, install correctly
as Fig. 2-7-D.
3. In case of the Tension Connect installation, install as
the circled section of Fig. 2-7-E.
Fig. 2-6-B
Loading Motor
Tension Band
Tension Connect
Fig. 2-7-C
Cassette Opener
[OK]
Tension Connect
Fig. 2-6-C
Tension Band
[NG]
Tension Connect
Tension Band
Pink
Loading Motor
Capstan DD Unit
-
L2
+
L1
White
Fig. 2-7-D
Tension Connect
Fig. 2-6-D
Main Chassis
B2-2
Fig. 2-7-E
DISASSEMBLY INSTRUCTIONS
2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A)
1. Remove the T Brake Spring.
2. Turn the T Brake Arm clockwise and bend the hook
section to remove it.
3. Unlock the 2 supports 1 and remove the T Brake
Band.
Idler Gear
Idler Arm Ass'y
(B)
S Reel
T Brake Band
(A)
1
Hook section
1
T Reel
(A)
T Brake Arm
1
T Brake Spring
1
Fig. 2-8-A
Fig. 2-9-A
NOTE
NOTE
1. In case of the S Reel and T Reel installation, check if the
correct parts are installed. (Refer to Fig. 2-9-B)
2. In case of the Idler Arm Ass'y installation, install correctly
as Fig. 2-9-C. And also set it so that the section "B" of
Fig. 2-9-A is placed under the Main Chassis tab.
1. In case of the T Brake Band installation, install correctly
as Fig. 2-8-B.
[OK]
T Brake Arm
T Brake Band
T Brake Arm
[NG]
T Brake Band
Fig. 2-8-B
2-9: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR
(Refer to Fig. 2-9-A)
Big Hole
(S Reel)
1. Remove the S Reel and T Reel.
2. Remove the 2 Polyslider Washers 1.
3. Remove the Idler Arm Ass'y and Idler Gear.
Small Hole
(T Reel)
Fig. 2-9-B
[OK]
Clutch Gear
Idler Arm Ass'y
NOTE
1. Take care not to damage the gears of the S Reel and T
Reel.
2. The Polyslider Washer may be remained on the back of
the reel.
3. Take care not to damage the shaft.
4. Do not touch the section "A" of S Reel and T Reel. (Use
gloves.) (Refer to Fig. 2-9-A) Do not adhere the stains
on it.
5. When you install the reel, clean the shaft and grease it.
(If you do not grease, noise may be heard in FF/REW
mode.)
6. After installing the reel, adjust the height of the reel.
(Refer to MECHANICAL ADJUSTMENT)
[NG]
Idler Arm Ass'y
Clutch Gear
Fig. 2-9-C
B2-3
DISASSEMBLY INSTRUCTIONS
2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/
P5 ARM ASS'Y (Refer to Fig. 2-10-A)
1. Unlock the support 1 and remove the Cassette
Opener.
2. Remove the Pinch Roller Block and P5 Arm Ass'y.
Cassette Opener
1
Spring Position
Fig. 2-11-B
2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12)
Pinch Roller Block
1. Remove the screw 1.
2. Remove the FE Head.
P5 Arm Ass'y
1
Main Chassis
FE Head
Fig. 2-10-A
NOTE
1. Do not touch the Pinch Roller. (Use gloves.)
2. In case of the Pinch Roller Block and the Pinch Roller
Cam installation, install correctly as Fig. 2-10-B.
Pinch Roller Block
• Screw Torque: 5 ± 0.5kgf•cm
• The FE Head is not installed on the Video Cassette Player.
Can be seen the hole of
the Pinch Roller Cam.
2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y
(Refer to Fig. 2-13)
P5 Arm Ass'y
Can be seen the hole of the
Main Cam.
1. Unlock the support 1 and remove the AHC Ass'y.
2. Disconnect the following connector:
(CD2001)
3. Remove the 3 screws 2.
4. Remove the Cylinder Unit Ass'y.
Fig. 2-10-B
2-11: A/C HEAD (Refer to Fig. 2-11-A)
1.
2.
3.
4.
Fig. 2-12
NOTE
Remove the screw 1.
Remove the A/C Head Base.
Remove the 3 screws 2.
Remove the A/C Head and A/C Head Spring.
1. When you install the Cylinder Unit Ass'y, tighten the
screws from (1) to (3) in order while pulling the Ass'y
toward the left front direction.
NOTE
1. Do not touch the A/C Head. (Use gloves.)
2. When you install the A/C Head Spring, install as shown in
Fig. 2-11-B.
3. When you install the A/C Head, tighten the screw (1) first,
then tighten the screw (2), finally tighten the screw (3).
(1)
2
Cylinder Unit Ass'y
AHC Ass'y
1
(3)
2
2
(2)
A/C Head
(3)
2
(2)
2
(1)
A/C Head Spring
2
• Screw Torque: 3 ± 0.5kgf•cm
1
A/C Head Base
• Screw Torque: 5 ± 0.5kgf•cm (Screw 1)
Fig. 2-11-A
B2-4
Fig. 2-13
DISASSEMBLY INSTRUCTIONS
2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14-A)
2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR
(Refer to Fig. 2-15-A)
1. Remove the Capstan Belt.
2. Remove the 3 screws 1.
3. Remove the Capstan DD Unit.
1. Remove the E-Ring 1, then remove the Main Cam.
2. Remove the E-Ring 2, then remove the Pinch Roller
Cam and Joint Gear.
1
Main Cam
Capstan Belt
Capstan DD Unit
2
Pinch Roller Cam
Joint Gear
1
• Screw Torque: 4 ± 0.5kgf•cm
Fig. 2-15-A
1 1
NOTE
Fig. 2-14-A
1. In case of the Pinch Roller Cam and Main Cam
installation, install them as the circled section of Fig. 215-B so that the each markers are met. (Refer to Fig.
2-15-B)
NOTE
1. In case of the Capstan DD Unit installation, apply the
silicon bond (TSE3843-W) on the position Fig. 2-14-B
correctly. (If no silicon bond applied, abnormal noise will
be heard on the deck operation.)
(Refer to Fig. 2-14-B, C)
Pinch Roller Cam
Applied position of
silicon bond
Marker
Be careful not to apply the silicon
bond to the Pinch Roller.
Main Cam
Fig. 2-15-B
Fig. 2-14-B
2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A)
1. Remove the E-Ring 1 and remove the Main Loading
Gear.
2. Remove the Main Rod, Tension Lever, Loading Arm S
Unit and Loading Arm T Unit.
Silicon Bond
Main Chassis
1
Main Rod
Main Loading Gear
Capstan DD Unit
Fig. 2-14-C
Loading Arm T Unit
Tension Lever
Loading Arm S Unit
Fig. 2-16-A
B2-5
DISASSEMBLY INSTRUCTIONS
2-18: CASSETTE GUIDE POST/INCLINED BASE S/T
UNIT/P4 CAP (Refer to Fig. 2-18-A)
NOTE
1. When you install the Loading Arm S Unit, Loading Arm
T Unit and Main Loading Gear, align each marker.
(Refer to Fig. 2-16-B)
1. Remove the P4 Cap.
2. Unlock the support 1 and remove the Cassette Guide
Post.
3. Remove the Inclined Base S Unit and Inclined Base T
Unit.
Marker
Main Loading Gear
Cassette Guide Post
1
Marker
Inclined Base S
Unit
Loading Arm T Unit
Inclined Base T
Unit
P4 Cap
Loading Arm S Unit
Fig. 2-16-B
2-17: CLUTCH ASS'Y/RING SPRING/CLUTCH LEVER/
CLUTCH GEAR (Refer to Fig. 2-17-A)
1.
2.
3.
4.
Remove the Polyslider Washer 1.
Remove the Clutch Ass'y and Ring Spring.
Remove the Clutch Lever.
Remove the Coupling Gear, Coupling Spring and
Clutch Gear.
Fig. 2-18-A
NOTE
1. Do not touch the roller of Guide Roller.
2. In case of the P4 Cap installation, install it with parallel
for "A" and "B" of Fig. 2-18-B.
3. In case of the Cassette Guide Post installation, install
correctly as the circled section of Fig. 2-18-C.
1
Clutch Ass'y
Ring Spring
"A"
Coupling Gear
"B"
Clutch Lever
Coupling Spring
Clutch Gear
P4 Cap
Cassette Opener
Fig. 2-18-B
Fig. 2-17-A
NOTE
[OK]
1. In case of the Clutch Ass'y installation, install it with
inserting the spring of the Clutch Ass'y into the dent of
the Coupling Gear. (Refer to Fig. 2-17-B)
Cassette Guide Post
Clutch Ass'y
[NG]
Cassette Guide Post
Coupling Gear
Fig. 2-18-C
Fig. 2-17-B
B2-6
DISASSEMBLY INSTRUCTIONS
3. When IC starts moving back and forth easily after
desoldering completely, pickup the corner of the IC using
a tweezers and remove the IC by moving with the IC
desoldering machine. (Refer to Fig. 3-3.)
3. REMOVAL AND INSTALLATION OF
FLAT PACKAGE IC
REMOVAL
NOTE
1. Put the Masking Tape (cotton tape) around the Flat
Package IC to protect other parts from any damage.
(Refer to Fig. 3-1.)
Some ICs on the PCB are affixed with glue, so be
careful not to break or damage the foil of each IC
leads or solder lands under the IC when removing it.
NOTE
Masking is carried out on all the parts located within
10 mm distance from IC leads.
Masking Tape
(Cotton Tape)
Blower type IC
desoldering
machine
IC
Tweezers
Fig. 3-1
IC
Fig. 3-3
2. Heat the IC leads using a blower type IC desoldering
machine. (Refer to Fig. 3-2.)
4. Peel off the Masking Tape.
NOTE
5. Absorb the solder left on the pattern using the Braided
Shield Wire. (Refer to Fig. 3-4.)
Do not add the rotating and the back and forth
directions force on the IC, until IC can move back and
forth easily after desoldering the IC leads completely.
NOTE
Do not move the Braided Shield Wire in the vertical
direction towards the IC pattern.
Blower type IC
desoldering machine
Braided Shield Wire
Soldering Iron
IC
IC pattern
Fig. 3-2
B3-1
Fig. 3-4
DISASSEMBLY INSTRUCTIONS
INSTALLATION
4. When bridge-soldering between terminals and/or the
soldering amount are not enough, resolder using a Thintip Soldering Iron. (Refer to Fig. 3-8.)
1. Take care of the polarity of new IC and then install the
new IC fitting on the printed circuit pattern. Then solder
each lead on the diagonal positions of IC temporarily.
(Refer to Fig. 3-5.)
Thin-tip Soldering Iron
IC
Soldering Iron
Fig. 3-8
5. Finally, confirm the soldering status on four sides of the
IC using a magnifying glass.
Confirm that no abnormality is found on the soldering
position and installation position of the parts around the
IC. If some abnormality is found, correct by resoldering.
Solder temporarily
Solder temporarily
Fig. 3-5
2. Supply the solder from the upper position of IC leads
sliding to the lower position of the IC leads.
(Refer to Fig. 3-6.)
Solder
IC
NOTE
When the IC leads are bent during soldering and/or
repairing, do not repair the bending of leads. If the
bending of leads are repaired, the pattern may be
damaged. So, be always sure to replace the IC in this
case.
Soldering Iron
Supply soldering
from upper position
to lower position
Fig. 3-6
3. Absorb the solder left on the lead using the Braided
Shield Wire. (Refer to Fig. 3-7.)
NOTE
Do not absorb the solder to excess.
Soldering Iron
IC
Braided Shield Wire
Fig. 3-7
B3-2
KEY TO ABBREVIATIONS
A A/C
ACC
AE
AFC
AFT
AFT DET
AGC
AMP
ANT
A.PB
APC
ASS’Y
AT
AUTO
A/V
B BGP
BOT
BPF
BRAKE SOL
BUFF
B/W
C C
CASE
CAP
CARR
CH
CLK
CLOCK (SY-SE)
COMB
CONV
CPM
CTL
CYL
CYL-M
CYL SENS
D DATA (SY-CE)
dB
DC
DD Unit
DEMOD
DET
DEV
E E
EF
EMPH
ENC
ENV
EOT
EQ
EXT
F F
FBC
FE
FF
FG
FL SW
FM
FSC
FWD
G GEN
GND
H H.P.F
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Audio/Control
Automatic Color Control
Audio Erase
Automatic Frequency Control
Automatic Fine Tuning
Automatic Fine Tuning Detect
Automatic Gain Control
Amplifier
Antenna
Audio Playback
Automatic Phase Control
Assembly
All Time
Automatic
Audio/Video
Burst Gate Pulse
Beginning of Tape
Bandpass Filter
Brake Solenoid
Buffer
Black and White
Capacitance, Collector
Cassette
Capstan
Carrier
Channel
Clock
Clock (Syscon to Servo)
Combination, Comb Filter
Converter
Capstan Motor
Control
Cylinder
Cylinder-Motor
Cylinder-Sensor
Data (Syscon to Servo)
Decibel
Direct Current
Direct Drive Motor Unit
Demodulator
Detector
Deviation
Emitter
Emitter Follower
Emphasis
Encoder
Envelope
End of Tape
Equalizer
External
Fuse
Feed Back Clamp
Full Erase
Fast Forward, Flipflop
Frequency Generator
Front Loading Switch
Frequency Modulation
Frequency Sub Carrier
Forward
Generator
Ground
High Pass Filter
I
K
L
M
N
O
P
R
S
C1-1
H.SW
Hz
IC
IF
IND
INV
KIL
L
LED
LIMIT AMP
LM, LDM
LP
L.P.F
LUMI.
M
MAX
MINI
MIX
MM
MOD
MPX
MS SW
NC
NR
OSC
OPE
PB
PB CTL
PB-C
PB-Y
PCB
P. CON
PD
PG
P-P
R
REC
REC-C
REC-Y
REEL BRK
REEL S
REF
REG
REW
REV, RVS
RF
RMC
RY
S. CLK
S. COM
S. DATA
SEG
SEL
SENS
SER
SI
SIF
SO
SOL
SP
STB
SW
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Head Switch
Hertz
Integrated Circuit
Intermediate Frequency
Indicator
Inverter
Killer
Left
Light Emitting Diode
Limiter Amplifier
Loading Motor
Long Play
Low Pass Filter
Luminance
Motor
Maximum
Minimum
Mixer, mixing
Monostable Multivibrator
Modulator, Modulation
Multiplexer, Multiplex
Mecha State Switch
Non Connection
Noise Reduction
Oscillator
Operation
Playback
Playback Control
Playback-Chrominance
Playback-Luminance
Printed Circuit Board
Power Control
Phase Detector
Pulse Generator
Peak-to Peak
Right
Recording
Recording-Chrominance
Recording-Luminance
Reel Brake
Reel Sensor
Reference
Regulated, Regulator
Rewind
Reverse
Radio Frequency
Remote Control
Relay
Serial Clock
Sensor Common
Serial Data
Segment
Select, Selector
Sensor
Search Mode
Serial Input
Sound Intermediate Frequency
Serial Output
Solenoid
Standard Play
Serial Strobe
Switch
KEY TO ABBREVIATIONS
S SYNC
SYNC SEP
T TR
TRAC
TRICK PB
TP
U UNREG
V V
VCO
VIF
VP
V.PB
VR
V.REC
VSF
VSR
VSS
V-SYNC
VT
X X’TAL
Y Y/C
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Synchronization
Sync Separator, Separation
Transistor
Tracking
Trick Playback
Test Point
Unregulated
Volt
Voltage Controlled Oscillator
Video Intermediate Frequency
Vertical Pulse, Voltage Display
Video Playback
Variable Resistor
Video Recording
Visual Search Fast Forward
Visual Search Rewind
Voltage Super Source
Vertical-Synchronization
Voltage Tuning
Crystal
Luminance/Chrominance
C1-2
SERVICE MODE LIST
This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.
To enter to the SERVICE MODE function, press and hold both buttons simultaneously on the main unit or on the main unit
and on the remote control for more than a standard time (second).
Set Key
Set Key
FF
CH UP
Standard Time
(seconds)
2
Operations
PLAY/REC total hours are displayed on the screen.
Refer to the “PREVENTIVE CHECKS AND SERVICE INTERVALS”
(CONFIRMATION OF HOURS USED).
Can be checked of the INITIAL DATA of MEMORY IC.
Refer to the “WHEN REPLACING EEPROM (MEMORY) IC”.
CH UP
STOP
CH UP
PLAY
2
Adjust the PG SHIFTER automatically.
Refer to the “ELECTRICAL ADJUSTMENT” (PG SHIFTER).
2
Initialization of the factory on VCR.
NOTE: Do not use this for the normal servicing.
If you set a factory initialization, the memories are reset such as
the clock setting, the channel setting, and PLAY/REC total hours.
VCR operation mode at no connection of DVD.
Refer to the “PREPARATION FOR SERVICING”
NOTE: Although the DVD is connected, the DVD mode cannot be
selected.
CH DOWN
POWER
2
Set Key
Remocon Key
Standard Time
(seconds)
REC
4
REC
6
STOP
1
Operations
2
Initialization of the factory on DVD.
NOTE: Do not use this for the normal servicing.
The function will only work without the setting of DVD disc at
DVD mode.
While pressing the Remocon Key for more than the Standard
Time, press the Set Key simultaneously.
2
DVD Write mode.
Refer to the “RE-WRITE FOR DVD FIRMWARE”.
NOTE: Do not use this for the normal servicing.
The function will only work at the DVD stop mode.
3
Check for the firmware version.
Refer to the “RE-WRITE FOR DVD FIRMWARE”.
NOTE: Do not use this for the normal servicing.
The function will only work at the DVD stop mode.
Method
Operations
Press the ATR button on the
remote control for more than
2 seconds during PLAY.
Adjusting of the Tracking to the center position.
Refer to the “MECHANICAL ADJUSTMENT” (GUIDE ROLLER) and “ELECTRICAL
ADJUSTMENT” (PG SHIFTER).
Make the short circuit
between the test point of
SERVICE and the GND.
The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated
without a cassette tape.
Refer to the “PREPARATION FOR SERVICING”
C2-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
The following standard table depends on environmental conditions and usage.
Parts replacing time does not mean the life span for individual parts.
Also, long term storage or misuse may cause transformation and aging of rubber parts.
The following list means standard hours, so the checking hours depends on the conditions.
Time
Parts Name
500
hours
1,000
hours
1,500
hours
2,000
hours
Audio Control Head
2,500
hours
Notes
Clean those parts in
contact with the tape.
Full Erase Head
(Recorder only)
Capstan Belt
Clean the rubber, and parts
which the rubber touches.
Pinch Roller
Capstan DD Unit
Loading Motor
Tension Band
T Brake Band
Clutch Ass’y
Idler Arm Ass’y
Capstan Shaft
Tape Running
Guide Post
Replace when rolling
becomes abnormal.
Cylinder Unit
Clean the Head
: Clean
: Check it and if necessary, replace it.
CONFIRMATION OF HOURS USED
PLAY/REC total hours can be checked on the FIP.
Total hours are displayed in 16 system of notation.
NOTE: If you set a factory initialization, the total hours is reset to “0”.
1. Turn on the POWER.
2. While pressing the CH UP button on the set, press the FF button on the set for more than 2 seconds.
3. Adjust the ADDRESS to "FD" by SET + or - button and read the DATA.
(This DATA becomes the thousands digit and hundreds digit value of the following formula.)
4. Adjust the ADDRESS to "FE" by SET + or - button and read the DATA.
(This DATA becomes the tens digit and ones digit value of the following formula.)
5. After the confirmation of using hours, turn off the power.
ADDRESS
DATA
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
PREVENTIVE CHECKS AND SERVICE INTERVALS
2. TAPE RUNNING SYSTEM
CLEANING
When cleaning the tape transport system, use the
gauze moistened with isopropyl alcohol.
NOTE
After cleaning the heads with isopropyl alcohol, do not
run a tape until the heads dry completely. If the heads
are not completely dry and alcohol gets on the tape,
damage may occur.
3. CYLINDER
Wrap a piece of chamois around your finger. Dip it in
isopropyl alcohol. Hold it to the cylinder head softly.
Turn the cylinder head counterclockwise to clean it (in
the direction of the arrow). (Refer to the figure below.)
1. AUDIO CONTROL HEAD
Clean the Audio Control Head with the cotton stick
soaked by alcohol. Clean the full erase head in the
same manner. (Refer to the figure below.)
NOTE
Do not exert force against the cylinder head. Do not move
the chamois upward or downward on the head.
Use the chamois one by one.
Cylinder Head
Audio Control Head
C3-2
RE-WRITE FOR DVD FIRMWARE
1. Turn on the power, and set the DVD mode.
2. Open the DVD tray.
3. Press both Channel button (6) on the remote control and the REC button on the set for more than 2 seconds.
4. Press OPEN/CLOSE button on the unit to check if all the keys on the unit do not function.
NOTE: To check if DVD Write mode is set.
When inserting Up-Date Disc at Non DVD Write mode, the read error will happen.
5. Place the Up-Date Disc and close the tray by hand. (Refer to SERVICING FIXTURE AND TOOLS)
6. Automatic read will start and "ROM_WRITE_START" will be displayed on the screen.
At this time, the horizontal noise lines may appear. But no problem.
7. Approxi. 60 seconds later, the tray will open automatically.
8. Remove the Up-Date Disc and close the tray by hand.
9. Unplug the AC cord, then plug it in.
10. After the write, set to the initializing of shipping.
Set to the DVD mode, press both Channel button (4) on the remote control and the REC button on the set for more than 2
seconds.
11. The "COMPLETE" will appear on the screen.
Then unplug the AC cord, and plug it in.
12. CHECK FOR THE FIRMWARE VERSION
Set to the DVD mode, press both Channel button (1) on the remote control and the STOP button on the set for more than
3 seconds.
Firmware version will be displayed on the top left of the screen.
(SD-22VB, SD-22VE)
Version OSD : TG025150
T G 0 2 5 1 5 0
Fixed
Released times on the same date
Release date (Example: 2002.5.15)
When the changed version displays, the Re-write will be completed.
(SD-22VL)
Version OSD : TG125150
A = October
B = November
C = December
T G 1 2 5 1 5 0
Fixed
Released times on the same date
Release date (Example: 2002.5.15)
When the changed version displays, the Re-write will be completed.
13. Turn off the power
C4-1
A = October
B = November
C = December
WHEN REPLACING EEPROM (MEMORY) IC
If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to
ensure correct data settings while making reference to TABLE 1.
NOTE: INI FD and INI FE cannot be set. Because, the total time for the PLAY/REC of the main unit is recorded.
(SD-22VB)
INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
C0
---
---
---
---
8B
C9
D2
01
FF
FF
FF
FF
F1
64
2D
8A
D0
9B
17
81
00
02
FF
03
01
7D
9F
02
02
42
35
23
5B
E0
76
5F
08
F8
04
FB
B2
9A
92
8C
51
5F
09
F0
05
F3
F0
B2
2F
9C
42
42
80
3D
6B
0B
7E
04
3A
00
---
---
---
(SD-22VE)
INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
B0
---
---
---
---
---
---
---
---
---
8B
C9
D2
71
6F
A9
00
C0
B2
17
90
50
60
F1
58
51
51
D1
B2
9F
97
8E
07
FA
D0
DD
66
2A
08
02
FF
40
00
7D
9F
82
02
42
35
63
5B
E0
76
5F
08
F0
0A
FB
5E
08
F0
00
F2
5F
09
F0
05
F3
F0
16
2F
9F
42
42
80
3D
68
08
89
04
3A
00
---
---
---
(SD-22VL)
INI
+0
+1
+2
+3
+4
+5
+6
+7
+8
+9
+A
+B
+C
+D
+E
+F
B0
---
---
---
---
---
---
---
---
---
8B
C9
D2
71
6F
A9
00
C0
B2
17
00
00
00
F1
58
51
00
D1
B2
9F
97
8E
07
CA
D0
DF
E2
45
08
02
FF
00
00
7D
9F
82
02
42
35
23
5B
E0
76
5F
08
F0
0A
FB
5E
00
00
00
F2
5F
09
F0
05
F3
F0
12
2F
9F
42
42
80
3D
68
08
89
04
3A
00
---
---
---
Table 1
1. Turn on the POWER.
2. Press both CH UP button on the set and the FF button on the set for more than 2 seconds.
ADDRESS and DATA will appear on FIP as Fig 1.
3.
4.
5.
6.
7.
8.
ADDRESS
DATA
Fig. 1
ADDRESS is now selected and should “blink”. Using the SET + or - button on the remote, step through the ADDRESS until
required ADDRESS to be changed is reached.
Press ENTER to select DATA. When DATA is selected, it will “blink”.
Again, step through the DATA using SET + or - button until required DATA value has been selected.
Pressing ENTER will take you back to ADDRESS for further selection if necessary.
Repeat steps 3 to 6 until all data has been checked.
When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.
After the data input, set to the initializing of shipping.
9. Turn POWER on.
10.Press both CH UP button on the set and the PLAY button on the set for more than 2 seconds.
11. After the finishing of the initializing of shipping, the unit will turn off automatically.
The unit will now have the correct DATA for the new MEMORY IC.
C4-2
SERVICING FIXTURES AND TOOLS
Alignment Tape
Back tension cassette gauge
Torque cassette gauge
(KT-300NR)
Taper nut driver
ST-C6
ST-C7
70909103
70909199
70909228
VTR cleaning kit
VTR lubrication kit
Grease
JG002B Adapter
JG002E Dial Torque Gauge
(10~90gf•cm)
JG002F (60~600gf•cm)
JG022 Master Plane
JG024A Reel Disk Height
Adjustment Jig
JG153 X Value Adjustment
Screwdriver
JG154 Cable
JG176 Up-Date Disc
Tentelometer
Ref. No.
Part No.
JG002B
APJG002B00
Adapter
VSR Torque, Brake Torque (S Reel/T Reel Ass'y)
JG002E
APJG002E00
Dial Torque Gauge (10~90gf•cm)
Brake Torque (T Reel Ass'y)
JG002F
APJG002F00
Dial Torque Gauge (60~600gf•cm)
VSR Torque, Brake Torque (S Reel)
Parts Name
Remarks
JG022
APJG022000
Master Plane
Reel Disk Height Adjustment
JG024A
APJG024A00
Reel Disk Height Adjustment Jig
Reel Disk Height Adjustment
JG153
APJG153000
X Value Adjustment Screwdriver
X Value Adjustment
JG154
APJG154000
Cable
Used to connect the test point of SERVICE and GROUND
APJG176013
Up-Date Disc (SD-22VB, SD-22VE)
APJG176013
Up-Date Disc (SD-22VL)
JG176
Up-Date of the Firmware
PREPARATION FOR SERVICING
How to use the Servicing Fixture
1. Short circuit between TP3001 and Ground with the cable JG154.
(The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape.)
2. In case of using a cassette tape, press the EJECT button to insert or eject a cassette tape.
Turn on the power and re-check the cable before checking the trouble points.
When you servicing without the connection of DVD, perform the following operations before step 1.
While pressing the POWER button on the set for more than 2 seconds, press the CH DOWN button on the set simultaneously
at the Power OFF. Although the DVD is connected, the DVD mode cannot be selected.
D1-1
MECHANICAL ADJUSTMENTS
1-2: CONFIRMATION AND ADJUSTMENT OF TENSION
POST POSITION
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work.
1. Set to the PLAY mode.
2. Adjust the adjusting section for the Tension Arm
position so that the Tension Arm top is within the
standard line of Main Chassis.
3. While turning the S Reel clockwise, confirm that the
edge of the Tension Arm is located in the position
described above.
• Place an object which weighs between 450g~500g on
the Cassette Tape to keep it steady when you want to
make the tape run without the Cassette Holder. (Do not
place an object which weighs over 500g.)
1-1: CONFIRMATION AND ADJUSTMENT OF REEL
DISK HEIGHT
1. Turn on the power and set to the STOP mode.
2. Set the master plane (JG022) and reel disk height
adjustment jig (JG024A) on the mechanism framework,
taking care not to scratch the drum, as shown in Fig. 11-A.
3. While turning the reel and confirm the following points.
Check if the surface "A" of reel disk is lower than the
surface "B" of reel disk height adjustment jig (JG024A)
and is higher than the surface "C". If it is not passed,
place the height adjustment washers and adjust to
10(+2, -0)mm.
4. Adjust the other reel in the same way.
Standard line of Main Chassis
Tension Arm
0.5mm (Adjusting range)
Fig. 1-2-A
Adjusting section for the
Tension Arm position
Master Plane (JG022)
Tension Band
Reel Disk Height Adjustment Jig
(JG024A)
The Tension Arm top will
move to the inside direction
of the Main Chassis.
The Tension Arm top will
move to the outside direction
of the Main Chassis.
Bend
1-3: CONFIRMATION OF PLAYBACK TORQUE AND
BACK TENSION TORQUE DURING PLAYBACK
Fig. 1-1-A
Master Plane (JG022)
1. Load a video tape (E-180) recorded in standard speed
mode. Set the unit to the PLAY mode.
2. Install the tentelometer as shown in Fig. 1-3. Confirm that
the meter indicates 20 ± 2gf in the beginning of playback.
Reel Disk Height
Adjustment Jig
(JG024A)
Reel Disk
• USING A CASSETTE TYPE TORQUE TAPE (KT-300NR)
(B)
1. After confirmation and adjustment of Tension Post
position (Refer to item 1-2), load the cassette type
torque tape (KT-300NR) and set to the PLAY mode.
2. Confirm that the right meter of the torque tape indicates
50~90gf•cm during playback in SP mode.
3. Confirm that the left meter of the torque tape indicates
25~40gf•cm during playback in SP mode.
10(+0.2, -0)mm
(C)
(A)
Height Adjustment
Washer
2.6x4.7xT0.13
2.6X4.7xT0.25
Fig. 1-2-B
Tentelometer
Fig. 1-1-B
Video Tape
P1 Post
D2-1
Guide Roller
Fig. 1-3
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE
NOTE
1. Install the Torque Gauge (JG002F) and Adapter (JG002B)
on the S Reel. Set to the Picture Search (Rewind) mode.
(Refer to Fig.1-4-B)
2. Then, confirm that it indicates 120~180gf•cm.
If the torque is out of the range, replace the following
parts.
NOTE
Check item
Replacement Part
1-4
Idler Ass'y/Clutch Ass'y
1-5
Install the Torque Gauge on the reel disk firmly. Press the
REW button to turn the reel disk.
S Reel side: S Reel/Tension Band/Tension
Connect/Tension Arm Ass'y
T Reel side: T Reel/T Brake Band//T Brake
Spring/T Brake Arm
1-5: CONFIRMATION OF REEL BRAKE TORQUE
(S Reel Brake) (Refer to Fig. 1-4-B)
2. CONFIRMATION AND ADJUSTMENT
OF TAPE RUNNING MECHANISM
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Ass'y from the S Reel.
3. Install the Torque Gauge (JG002F) and Adapter
(JG002B) on the S Reel. Turn the Torque Gauge
(JG002F) clockwise.
4. Then, confirm that it indicates 60~100gf•cm.
Tape Running Mechanism is adjusted precisely at the
factory. Adjustment is not necessary as usual. When you
replace the parts of the tape running mechanism because
of long term usage or failure, the confirmation and
adjustment are necessary.
(T Reel Brake) (Refer to Fig. 1-4-B)
2-1: GUIDE ROLLER
1. Once set to the Fast Forward mode then set to the Stop
mode. While, unplug the AC cord when the Pinch Roller
Block is on the position of Fig. 1-4-A.
2. Move the Idler Ass'y from the T Reel.
3. Install the Torque Gauge (JG002E) and Adapter
(JG002B) on the T reel. Turn the Torque Gauge
(JG002E) counterclockwise.
4. Then, confirm that it indicates 30~50gf•cm.
1. Playback the VHS Alignment Tape.
2. Connect CH-1 of the oscilloscope to TP102 (Envelope)
and CH-2 to TP101 (SW Pulse).
3. Press and hold the ATR button on the remote control
more than 2 seconds to set tracking to center.
4. Trigger with SW Pulse and observe the envelope. (Refer
to Fig. 2-1-A)
5. When observing the envelope, adjust the Taper Nut
Driver slightly until the envelope will be flat.
Even if you press the Tracking Button, adjust so that
flatness is not moved so much.
6. Adjust so that the A : B ratio is better than 3 : 2 as shown
in Fig. 2-1-B, even if you press the Tracking Button to
move the envelope (The envelope waveform will begin to
decrease when you press the Tracking Button).
7. Adjust the PG shifter during playback.
(Refer to the ELECTRICAL ADJUSTMENTS)
The position at FF mode.
Pinch Roller Block
Stop at this position.
Cassette
Opener
The position at
STOP mode.
Capstan DD Unit
NOTE
After adjustment, confirm and adjust A/C head.
(Refer to item 2-2)
Cassette Holder Ass'y
Fig. 1-4-A
CH-1
Envelope
(TP102)
Torque Gauge/Adapter
(JG002F/JG002B)
CH-1
Track
Torque Gauge/Adapter
(JG002E/JG002B)
CH-2
Track
CH-2
SW Pulse (TP101)
Fig. 2-1-A
Entrance
Exit
S Reel
Max
T Reel
A
B
A:B≥3:2
Fig. 1-4-B
D2-2
Max
Fig. 2-1-B
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/
CONTROL HEAD
2-3: TAPE RUNNING ADJUSTMENT
(X VALUE ADJUSTMENT)
When the Tape Running Mechanism does not work well,
adjust the following items.
1. Confirm and adjust the height of the Reel Disk.
(Refer to item 1-1)
2. Confirm and adjust the position of the Tension Post.
(Refer to item 1-2)
3. Adjust the Guide Roller. (Refer to item 2-1)
4. Confirm and adjust the Audio/Control Head.
(Refer to item 2-2)
5. Connect CH-1 of the oscilloscope to TP101 and CH-2 to
TP102.
6. Playback the VHS Alignment Tape (Monoscope of ST-C6
MODE1).
7. Press and hold the Tracking-Auto button on the remote
control more than 2 seconds to set tracking to center.
8. Set the X Value adjustment driver (JG153) to the 4 of
Fig. 2-2-B. Adjust X value so that the envelope waveform
output becomes maximum. Then, check if the 5 section
of Fig. 2-2-B is on the center position (or rather to the
cylinder side). In case of the envelope maximum at the
difference position from the center, adjust the matching of
picture and sound again.
1. Playback the VHS Alignment Tape.
2. Confirm that the reflected picture of stamp mark is
appeared on the tape prior to P4 Cap as shown in Fig. 22-A.
a) When the reflected picture is distorted, turn the screw
1 clockwise until the distortion is disappeared.
b) When the reflected picture is not distorted, turn the
screw 1 counterclockwise until little distortion is
appeared, then adjust the a).
3. Turn the screw 2 to set the audio level to maximum.
4. Confirm that the bottom of the Audio/ Control Head and
the bottom of the tape is shown in Fig. 2-2-C.
c) When the height is not correct, turn the screw 3 to
adjust the height. Then, adjust the 1~3 again.
Audio/Control Head
Reflected picture of
Stamp Mark
P4 Cap
Stamp Mark
Fig. 2-2-A
Audio/Control Head
5
[OK]
[NG]
1
3
2
4
Fig. 2-2-B
Audio/Control Head
Tape
0.25±0.05mm
Fig. 2-2-C
D2-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
4
5
6
3
2
7
1
10
9
1. Tension Connect
2. Tension Arm
3. Guide Roller
4. Audio/Control Head
5. X value adjustment driver hole
8
6. P4 Post
7. T Brake Spring
8. T Reel
9. S Reel
10. Adjusting section for the Tension Arm position
D2-4
ELECTRICAL ADJUSTMENTS
Read and perform this adjustment when repairing the
circuits or replacing electrical parts or PCB assemblies.
1. BASIC ADJUSTMENT
CAUTION
When you exchange IC and Transistor for a heat sink,
apply the silicon grease on the contact section of the
heat sink. Before applying new silicon grease, remove
all the old silicon grease. (Old grease may cause
damages to the IC and Transistor.)
1-1: PG SHIFTER
CONDITIONS
MODE-PLAYBACK
Input Signal-Alignment Tape
INSTRUCTIONS
1. Connect CH-1 on the oscilloscope to TP101 and CH-2
to pin 19 of J8005.
2. Playback the alignment tape.
3. Press and hold the ATR button on the remote control
more than 2 seconds to set tracking to center.
4. Press both CH UP button on the set and the STOP
button on the set for more than 2 seconds.
CH-2
6.5H
CH-1
Fig. 1-1-A
CH-2
CH-1
6.5H
Fig. 1-1-B
D3-1
ELECTRICAL ADJUSTMENTS
2. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)
AC IN
POWER PCB
CP502
CP503
CD502
OS8001
J8001
J8002
J8003
CP1701
J8005
TP3001
CD8002
CD8502
CP8502
A/C HEAD
CD8501
CP8002
102
CD
TU301
CP8001
CP102
TP102
CP2602
CP653
TP101
CD651
CP651
CP2601
CP2603
VCR PCB
DVD PCB
CD652
CD4001
OPERATION 1 PCB
CD2601
CP601
OPERATION 2 PCB
DISPLAY PCB
DECK CD
D3-2
CD2603
CP681
TROUBLESHOOTING GUIDE
(VCR SECTION)
POWER DOES NOT TURN ON
Does display light?
NO
Is the voltage at pin
15,16 of CP502?
NO
Check peripheral circuit of T501.
YES
YES
Check IC3001.
Is there voltage at
pin 20 of IC 3001?
YES
Check Q506, Q504.
NO
Check IC3001.
E-1
TROUBLESHOOTING GUIDE
THE POWER SUPPLY CUT
Inserting a cassette
and push play button.
Does the power cut
after 3 seconds?
YES
Check CAPSTAN DD UNIT
and CYLINDER UNIT.
NO
Does the power cut
after about 6 seconds?
YES
Check Q3006, Q3007
and CAPSTAN BELT.
NO
Does intermittently
the power cut?
YES
Check Q3006, Q3007, IC3001
and sag of CAPSTAN BELT.
NO
Check the POWER BLOCK.
E-2
TROUBLESHOOTING GUIDE
AT PLAYBACK AND RECORDING,
CYLINDER MOTOR UNLOAD
Is the voltage at pin 8 of
CP3001 about DC12.6V?
Check at 12.6V line,
power block.
NO
YES
In playback, is at pin 12 of
NO
Check IC3001.
CP3001 about DC2.6V?
YES
Change CYLINDER MOTOR.
E-3
TROUBLESHOOTING GUIDE
AUDIO SHAKES
Is AUDIO HEAD
scratched?
YES
Change AUDIO HEAD.
NO
At playback, is input about
4.5Vp-p of a rectangular
NO
Change CAPSTAN DD UNIT.
wave at pin 85 of IC3001?
YES
At playback, is pin 5 of
CP3001 3.5V?
NO
Check IC3001.
YES
Check AUDIO BLOCK.
E-4
TROUBLESHOOTING GUIDE
The CASSETTE TAPE
CAN NOT BE INSERTED
When a CASSETTE can
NO
Check LED of DECK,
PHOTO SENSOR.
YES
Change
not inserted, is pin 10 of
IC3001 5V ?
YES
When a CASSETTE is
inserted, is pin 8 of
CP3001 12.6V ?
LOADING MOTOR.
NO
When a CASSETTE is
inserted, is pin 47 of
IC3001 5V ?
NO
Change IC3001.
YES
Check circuit of loading motor.
E-5
TROUBLESHOOTING GUIDE
When inserting a CASSETTE,
it ejects immediately.
Does another CASSETTE
Defective CASSETTE
or cassette loading
block.
NO
insert?
YES
Does SW3001 and
NO
Correctly SW3001
and REC LEVER set.
REC LEVER
correctly set ?
YES
After inserting
CASSETTE, is pin 81
of IC3001 0V ?
NO
Check SW3001.
YES
Check IC3001.
E-6
TROUBLESHOOTING GUIDE
Can not FF/REW
At FF/REW, does voltage
at pin 11 of IC3001
Check line of IC3001
at pin 3 and pin 4.
NO
change?
YES
Check DECK MECHANISM.
E-7
TROUBLESHOOTING GUIDE
TAPE loading is ok, but
unloads immediately.
Does CYLINDER
NO
rotate?
Is the voltage
at pin 8 of CP3001
12.6V?
YES
YES
At play, is the voltage
at pin 12 of CP3001 2.6V?
YES
Change CYLINDER unit.
NO
Is there HEAD SW
PULSE at TP101?
YES
NO
NO
Is PG PULSE signal
inputted to pin 81
of IC3001?
YES
Change IC3001.
Check Q3006 and Q3007.
E-8
NO
Check power block.
TROUBLESHOOTING GUIDE
At play,the picture
jitters vertical minutely
Is FG wave of CP3001
at pin 11 5V?
NO
Change
CYLINDER MOTOR.
5V
YES
NO
Is pin 12 of CP3001 2.6V?
Change IC3001.
YES
Change CYLINDER MOTOR
E-9
TROUBLESHOOTING GUIDE
Auto tracking
does not operate
In auto tracking, is the
voltage at pin 8 of IC3001
more than DC 0.2V?
YES
Does the CLT pulse
NO
signal (about 2.5Vp-p)
appear at pin 97 of IC3001?
2.5Vp-p
YES
CHANGE IC3001.
E-10
NO
Check CONTROL HEAD.
TROUBLESHOOTING GUIDE
WHEN PLAYBACK, FF OR REW
MODE IS ACTIVE , UNIT STOPS
IMMEDIATELY
Does CAPSTAN DD
Refer to section "CAPSTAN
DD MOTOR NOT
ROTAING".
NO
MOTOR rotate?
YES
Is there REEL SENSOR
PULSE signal at pin 79
and pin 80 of IC3001?
NO
Check Q3006 and Q3007.
YES
Change IC3001.
E-11
TROUBLESHOOTING GUIDE
AT PLAY, PICTURE JITTERS
HORIZONTALLY
NO
Does a noise on the picture
appear?
YES
By adjusting the MANUAL
TRACKING UP/DOWN
BUTTONS, will the line
NO
Check P/B ENVELOPE.
disappear?
YES
Is a height of GUIDE POST
maximum?
NO
The height of GUIDE POST
readjust.
YES
Is PG SHIFTER
adjustment 6.5H?
NO
Adjust PG SHIFTER.
YES
Is a wave of PB-Y unusual?
NO
Change IC101.
YES
Change IC3001.
E-12
TROUBLESHOOTING GUIDE
AT PLAYBACK, THE PICTURE
DOES NOT APPEAR
NO
Is E-E appearing on
the MONITOR TV?
NO
Is the voltage of IC101 at
pin 12, 36, 61, 90 and 96
Check POWER BLOCK.
5V?
YES
YES
Check video out line and
IC101.
Is there FM signal at pin
78 and 79 of IC101?
Check connection of the
CYLINDER.
NO
YES
Is there video signal
NO
Change IC101.
at pin 52 of IC101?
YES
Check IC4501.
E-13
TROUBLESHOOTING GUIDE
AT PLAYBACK, THE COLOR DOES
NOT APPEAR
Does composite signal
appear at pin 52 of
NO
Change IC101.
IC101?
YES
Check pin 21 and 19 of
IC4501.
E-14
TROUBLESHOOTING GUIDE
PLAYBACK PICTURE IS NOISY
(EVEN AFTER CLEANING HEADS)
Is FM signal at pin 79 of
NO
Check CYLINDER.
IC101 270 mVp-p ?
YES
Is FM signal at pin 8 of IC3001
YES
Perform the interchange
more than 1V?
able adjustment of DECK.
NO
Is VIDEO output at pin 19 of
NO
Check IC101 and IC4501.
IC4501 2Vp-p, and are
there any noises?
YES
Change J8005.
E-15
TROUBLESHOOTING GUIDE
NO COLER DURING SELF
RECORDING AND PLAYBACK
Does VIDEO signal appear
at pin 31 of IC101?
Check IC8001
NO
circuit around it.
YES
Does COLOR signal at pin 52
of IC101?
NO
Change IC101.
YES
Check pin 20 and pin 19 of IC4501.
E-16
TROUBLESHOOTING GUIDE
AT PLAY, AUDIO DOES NOT
APPEAR
At E-E, does audio appear?
Refer to section "E-E DOES
NOT APPEAR".
NO
YES
Does AUDIO signal
appear at pin 2 of IC101
6mVp-p?
Check C117 and peripheral
circuit.
NO
YES
Does AUDIO signal
appear at pin 11 of IC101
1Vp-p?
NO
Change IC101.
YES
Check AUDIO HEAD for DEBRIS
STAINS. Check the connector from
AUDIO HEAD is fully inseted into
CP102. Replace IC101.
E-17
TROUBLESHOOTING GUIDE
CAPSTAN DD MOTOR NOT
ROTATING
In playback, is there voltage
at pin 2 of CP3001 12V?
NO
Check POWER BLOCK.
YES
Is the voltage at pin 8 of
CP3001 5V?
NO
Check POWER BLOCK.
YES
In playback, Check the
voltage at pin 5 of CP3001
NO
Change IC3001.
is 2V or at pin 12 of IC3001 is
2.5V?
YES
In playback, is there voltage
NO
Check pin 77, 78 of IC3001
and peripheral circuit.
at pin 9 of CP3001 2.5V?
YES
Replace IC3001. Does DD MOTOR
rorate now? If not, Replace DD
MOTOR.
E-18
TROUBLESHOOTING GUIDE
THE AUDIO CAN NOT
RECORD
Is bias level at L104 OK?
NO
Is the voltage at pin 2
NO
Check POWER circuit.
of L104 5V?
YES
YES
Is the voltage at pin 29
of IC3001 about 5V?
NO
Change IC3001.
L104 is broken or shorted.
Is there audio signal
at pin 5 of CP102?
Check the circuit between
pin 4 of IC101 to pin 5 of
NO
CP102.
YES
Is there audio signal
NO
Change IC101.
at pin 11 of IC101?
YES
Check lead wire of A/C HEAD
and CONNECTOR.
E-19
TROUBLESHOOTING GUIDE
THE CASSETTE INSERT, BUT
THE TAPE DOES NOT MOVE
Does the mode
appear at display?
Check LOADING MOTOR
and MODE SENSOR
NO
RELATION DEPARTMENT.
YES
Does operate with
NO
Check IC3001.
remote control?
YES
Check operation PCB.
E-20
TROUBLESHOOTING GUIDE
RECORDING MECHANISM WORKS,
BUT NO VIDEO RECORD FROM
INPUT JACK OR TUNER
Is there video signal at
Check circuit of video signal from
VIDEO IN or IC8001
to IC3001.
NO
pin 31of IC101?
YES
Does the VIDEO signal
appear at pin 52 of
IC101?
NO
Change IC101.
YES
Check CYLINDER UNIT and
circuit around of CP101.
E-21
TROUBLESHOOTING GUIDE
E-E DOES NOT APPEAR
(THE PICTURE DOES NOT
APPEAR FROM TUNER)
Does normality AU
DIO JACK CONNECT?
NO
Connection is done over again.
YES
Are there the voltage of
MB(5V), PB(5V), TU(32V)
NO
Check POWER BLOCK.
of TU301?
YES
Check the picture.
Is there video signal at
NO
Change TU301.
pin 24 of TU301?
YES
Is there video signal at
NO
Change IC101.
pin 28 of IC101?
YES
Is there video
waveform at pin 52 of
NO
Check IC101.
IC101?
YES
NO
Check pin19 and 21
of IC4501?
Change IC4501.
YES
Check pin 7 of IC8001.
E-22
TROUBLESHOOTING GUIDE
E-E AUDIO(MONO)
DOES NOT APPEAR
Is the voltage at pin 40
NO
Check POWER BLOCK.
of IC701 5V?
YES
Is the voltage at pin 34
of IC701 12V?
NO
Check POWER BLOCK.
YES
Does audio signal
appear at pin 36, 37, 42
and 43 of IC8001?
NO
Check J8002, J8005 and
peripheral circuit.
YES
Does audio signal appear
at pin 21 of IC701?
NO
Change IC701.
YES
Does audio signal appear
at pin 22 of IC701?
NO
Check IC101.
YES
Does audio signal appear
at pin 15 and 18 of
NO
Change IC701.
IC701?
YES
Check circuit around of J8005
and IC8001.
E-23
TROUBLESHOOTING GUIDE
E-E AUDIO (STEREO)
DOES NOT APPEAR
Is the voltage at pin 40
of IC701 5V?
NO
Check POWER BLOCK.
YES
Is the voltage at pin
NO
Check POWER BLOCK.
34 of IC701 12V?
YES
Is there video signal at
NO
Change IC701.
pin 10, 11 of IC701?
YES
Is there video signal at
NO
Change IC701.
pin 15, 18 of IC701?
YES
Check circuit around of IC8001
and J8005.
E-24
TROUBLESHOOTING GUIDE
TUNER AUDIO(MONO)
DOES NOT APPEAR
Does E-E AUDIO
(MONO) appear?
NO
Refer to section "E-E AUDIO
(MONO) DOES NOT APPEAR".
YES
Does audio signal
appear at pin 38 of
NO
Check pin 21 of TU301.
IC801?
YES
Does audio signal appear
NO
Change IC801.
at pin 1 and 2 of IC801?
YES
Does audio signal
appear at pin 15 and
18 of IC701?
NO
Change IC701.
YES
Check IC8001, J8005 and
peripheral circuit.
E-25
TROUBLESHOOTING GUIDE
TUNER AUDIO(STEREO)
DOES NOT APPEAR
Does signal appear at
pin 25 of IC801?
NO
Change TU301.
YES
Refer to section "TUNER AUDIO
(MONO) DOES NOT APPEAR".
E-26
TROUBLESHOOTING GUIDE
PB AUDIO (Hi-Fi)
DOES NOT APPEAR
Does E-E AUDIO
NO
Refer to section "E-E AUDIO
(STEREO) appear?
(STEREO) DOES NOT APPEAR".
YES
Does NORMAL PB
AUDIO appear?
NO
Refer to section "AT PLAY,
AUDIO DOES NOT APPEAR".
NO
Check circuit of HEAD AMP
and CYLINDER UNIT.
YES
Is there audio signal at
pin 35, 37 of IC701?
YES
Is there audio signal at
pin 15, 18 of IC701?
NO
Change IC701.
YES
Check IC8001, J8005 and
peripheral circuit.
E-27
TROUBLESHOOTING GUIDE
Hi-Fi AUDIO
CAN NOT RECORD
Does E-E AUDIO appear?
NO
Refer to section "E-E AUDIO
(MONO) DOES NOT APPEAR".
NO
Check circuit around of J602,
YES
AT state of video recording,
is there audio signal at pin 10
and 11 of IC701?
J603 and TU301.
YES
Is there audio signal at
NO
Change IC701.
pin 15, 18 of IC701?
YES
At recording and play, is
there signal at pin 7, 8
NO
Check CYLINDER UNIT.
and 9 of CP101?
YES
Check IC101.
E-28
TROUBLESHOOTING GUIDE
(DVD SECTION)
Deck does not accept
open/close
Is the DVD
NO
display out ?
Refer to section "DVD screen without
going out".
YES
Can it open and close
NO
Change DVD LOADER.
it manually? (*1)
YES
YES
Is there OSD display ?
Is the voltage
at pin 7, 8 and 20 of IC2602
8V?
NO
Change DVD LOADER
YES
Check IC2602 ,CP2603
and peripheral circuit.
NO
Check POWER BLOCK
*1:Turn GEAR of DVD DECK front lower part,
to open and close TRAY manually
E-29
TROUBLESHOOTING GUIDE
DVD screen without going out
Is there video signal
at pin 27 of IC8504?
YES
Check IC8001
and peripheral circuit.
YES
Check IC8504
and peripheral circuit.
NO
Is there waveform
at pin 102, 103, 105 and
106 of IC4001?
NO
Is there waveform
at pin 120 of IC4001?
NO
Is X8501 oscillating?
YES
YES
Change IC8501.
Are there waveform
at line HA1-HA17?
YES
Change IC4001.
NO
Change IC4006.
E-30
NO
Change X8501.
TROUBLESHOOTING GUIDE
Do not playback DVD
Does display "Please
YES
Check Disc" after
reading ?
NO
Is the voltage
at pin 6 of IC2603
about 1V?
YES
Change DVD LOADER
NO
Check IC2603
and peripheral circuit.
Are there oscillate
NO
Check IC2603
and peripheral circuit.
at pin 29, 30 of IC2603 ?
YES
Are there waveform
at line of DVD DATA 0-7 ?
YES
Check IC4001 and
peripheral circuit.
NO
Check IC2001
and peripheral circuit.
E-31
TROUBLESHOOTING GUIDE
DVD/CD ANALOG AUDIO DOES
NOT APPEAR
Are there waveform
at pin 136, 139 and 141
NO
Are there waveform
at line of DVD DATA 0-7?
YES
Change IC4001.
of IC4001?
YES
NO
Check IC2001
and peripheral circuit.
Are there waveform
NO
Change IC8503.
at pin 20, 23 of IC8503?
YES
Is the voltage at pin 3
NO
Check IC8004
and peripheral circuit.
of CP8502 about 5V?
YES
Check IC8503
and peripheral circuit.
E-32
TROUBLESHOOTING GUIDE
No digital audio on playback
Is there waveform
at pin 13 of CD8501?
YES
Check OS8001 and peripheral
circuit of J8001.
NO
Refer to section "DVD/CD
ANALOG AUDIO DOES NOT
NO
Is the Analog Audio
Sound?
APPEAR".
YES
Change IC2001.
E-33
TROUBLESHOOTING GUIDE
NO PLAYBACK PICTURE
OF Y.U.V OUT
Is there Y.U.V waveform at
pin 16, 18, 20 of IC8504?
YES
NO
Is there Y.U.V
waveform at pin 7, 9
and 11 of CP8002?
YES
Check circuit around of J8005.
NO
Check circuit around of CP8002.
Are there signals at pin
4, 11 and 13 of IC8504?
YES
Check circuit around of IC8504.
NO
Refer to section "DVD screen
without going out".
E-34
TROUBLESHOOTING GUIDE
No playback picture of
S-VIDEO jack
Are there Y signal at pin 23
YES
Check D8501 and circuit
around of D8502.
and C signal at pin 25 of
IC8504?
NO
Is the voltage at pin
1 of IC8504 about 8V?
NO
Check circuit around of Q8508.
YES
Are there signals at pin
4, 11 and 13 of IC8504?
YES
Check circuit around of IC8504.
NO
Refer to section "DVD screen
without going out".
E-35
MECHANICAL EXPLODED VIEW
704
704
704
704
635
630
CD102
629
631
701
701
703
703
701
704
703
703
640
703
637
625
623
703
PCB010
(VCR PCB ASS'Y)
636
703
627
703
628
616
PCB130
(DVD PCB ASS'Y)
703
624
703
CD8002
605
603
703
CD2603
703
606
CD652
CD2601
703
604
642
708
603
607
602
PCB240
703 (POWER PCB ASS'Y)
705
621 708
606
705
632
616
705
702
CD651
703
702
622
707
643
703
PCB390
(DISPLAY PCB ASS'Y)
626
620
619
702
706
641
706
618
634
702
617
614
639
706
613
609
610
612
PCB280
(OPERATION 2 PCB ASS'Y)
611
706
615
608
601
706
PCB270
(OPERATION 1 PCB ASS'Y)
J1-1
618
634
702
638
633
PACKING DIAGRAM
(SD-22VB, SD-22VL)
SD-22VB
INSTRUCTION BOOK
QUICK SET UP SHEET
REGISTRATION CARD
POLYBAG,INSTRUCTION(RED CAUTION)
SD-22VL
INSTRUCTION BOOK(G)
INSTRUCTION BOOK(I)
INSTRUCTION BOOK(S)
QUICK SET-UP SHEET
POLYBAG,INSTRUCTION(RED CAUTION)
CABLE, PAL
TRANSMITTER
PACKAGE, BACK
PAD,DVD/VR
GIFT SHEET
PACKAGE, BACK
PACKAGE, FRONT
GIFT BOX
J2-1
PACKING DIAGRAM
(SD-22VE)
INSTRUCTION BOOK (F)
INSTRUCTION BOOK (G)
QUICK SET-UP SHEET
POLYBAG,INSTRUCTION(RED CAUTION)
TRANSMITTER
CABLE,SECAM
CABLE,21PIN
PACKAGE, BACK
PAD,DVD/VR
GIFT SHEET
PACKAGE, BACK
PACKAGE, FRONT
GIFT BOX
J2-2
CHASSIS EXPLODED VIEW (TOP VIEW)
300
502
CD1501
348
M2003
UN4001
333
334
504
501
335
H5002
342
H5001
336
314
324
341
347
503
315
306
323
331
508
322
508
305
301
302
312
AA
313
AA
332
AA
AA
AA
AA
CD1502
M101
318
304
325
309
AA 319
AA
307
AA
506
AA
345
320
AA
346
AA
507
AA
316
317
AA
321
AA
AA
AA
CLASS
MARK
GREASE
AA
NOTE: Applying positions AA for the grease are
displayed for this section.
Check if the correct grease is applied for
each position.
J3-1
AA
CHASSIS EXPLODED VIEW (BOTTOM VIEW)
300
303
CD1501
M2001
510
AA
339
CD1502
338
AA
510
AA
329
337
AA
AA
AA
509
AA
510
AA
340
AA
311
310
AA
308
AA
344
327
343
AA
326
AA
328
AA
505
330
CLASS
MARK
GREASE
AA
NOTE: Applying positions AA for the grease are
displayed for this section.
Check if the correct grease is applied for
each position.
J3-2
REPLACEMENT PARTS LIST
Location
Part No.
No.
601
601
601
602
603
604
605
607
613
618
623
625
629
630
631
634
637
640
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
79097739
79097731
79097746
79099161
79099162
79099163
79099164
79099166
79099167
79099168
79099169
79097709
79099170
79099171
79099172
79097713
79097710
79097712
79097781
79097779
79097781
79097784
79097785
79097786
79097782
79097780
79097778
79097783
79097730
79099178
79099179
79099180
79099181
79099182
79099183
79099184
79099185
79099186
79099187
79099188
79099189
79099190
79099191
79099192
79099193
79099194
79099195
79099196
LG PART No.
A2A7A1E720
A2A7A0E720
A2A7A2E720
701WPA0686
701WPA0751
752WSA0230
753WUAA006
85OP700037
7235490018
704WPC0001
752WSA0275
753WUA0060
702WSB0066
712WPB0107
7235630003
800WR0A023
753WUA0062
800WFAA013
J2A7A101A
J2A7A001A
J2A7A101A
J2A7A201A
J2A7A210A
J2A7A211A
J2A7A107A
J2A7A007A
J2A78807A
J2A7A117A
A2A7A0E420A
85OA400234
85OA500026
85OP200290
85OP600581
85OP500083
85OP800324
85OA000459
85OA200089
85OA200090
85OA300065
85OA300066
85OA400223
85OA400232
85OA400235
85OA400231
85OP800358
85OP900736
85OP900748
85OP900749
Description
CABINET,FRONT ASSY, SD-22VB
CABINET,FRONT ASSY, SD-22VE
CABINET,FRONT ASSY, SD-22VL
HOLDER,DECK
HOLDER,DECK
SHIELD,CASE HEAD AMP
SPRING,EARTH HEAD AMP
HOLDER,LED
BADGE,BRAND
LEG,BOTTOM
COVER,AC HEAD
SPRING,EARTH
CABINET,TOP
PLATE,TRAY FRONT
SHEET,DVD
CUSHION
23x13xT3
SPRING,EARTH-TOP
CUSHION,LEG
INSTRUCTION BOOK, SD-22VB
INSTRUCTION BOOK, SD-22VE
INSTRUCTION BOOK, SD-22VL
INSTRUCTION BOOK, SD-22VL
INSTRUCTION BOOK, SD-22VL
INSTRUCTION BOOK, SD-22VL
QUICK SET-UP SHEET, SD-22VB
QUICK SET-UP SHEET, SD-22VE
QUICK SET-UP SHEET, SD-22VL
REGISTRATION CARD, SD-22VB
DECK ASSY A2A7A0E420A
PINCH ROLLER BLOCK
AHC ASS'Y
BELT,CAPSTAN (S)
WORM
BASE,AC HEAD
SPRING,AC HEAD
MAIN CHASSIS ASS'Y
CLUTCH ASS'Y
ARM IDLER ASS'Y
LOADING ARM S UNIT
LOADING ARM T UNIT
INCLINED BASE T UINT 3S
P5 ARM ASS'Y 2
TENSION ARM ASS'Y 2
INCLINED BASE S UNIT
SPRING,LOCKER
CASS,HOLDER
CASS,SIDE L
CASS,SIDE R
K1-1
Location
No.
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
501
502
503
504
505
506
507
508
509
510
CD1501
CD1502
H5001
H5002
M101
M2001
M2003
UN4001
R502
R504
R512
R516
R517
Part No.
LG PART No.
79099197
79099198
79099199
79099200
79099201
79099202
79099203
79099204
79099205
79099206
79099207
79099208
79099209
79097714
79099211
79099212
79097715
79099214
79099215
79099216
79099217
79099218
79099219
79099220
79099221
79099222
79099223
79099224
79099225
79099226
79099230
79099228
79099229
79099230
79099231
79099232
79099233
79099234
79099235
79099236
79099237
79099238
79099239
79097706
79099241
79099242
79097716
79097788
AD301141
79097789
79099005
79097787
85OP900739
85OA900228
85OP000496
85OP200316
85OP200317
85OP200308
85OP200311
85OP200312
85OP200313
85OP300194
85OP400490
85OP400492
85OP400520
85OP400542
85OP400533
85OP600573
85OP600584
85OP600577
85OP600578
85OP600579
85OP600582
85OP800322
85OP800360
85OP800355
85OP800356
85OP900750
85OP900744
85OP900745
85OP900746
8107226804
8109126604
8107226404
8102120604
8109126604
810A130404
810A126504
82Q264713N
82P184505N
83ETW30000
122H071603
122Y021902
1523D91034
1543D02013
1596S98001
1510S98036
1589S11017
A2A752B500
R3X1811R5J
R3X181561J
R3X18A823J
R63581R22J
R002T2681J
Description
LOCKER,R
LINK UNIT
POST,CASS GUIDE
REEL,S (S)
REEL,T (S)
GEAR,IDLER
GEAR,CLUTCH
GEAR,COUPLING
LEVER,CLUTCH
GEAR,MAIN LOADING
LEVER,TENSION
HOLDER,TENSION
CAP.P4
BAND,TENSION
CONNECT,TENSION
ARM,BRAKE T
BAND,BRAKE T
CAM,PINCH ROLLER
CAM,MAIN
ROD,MAIN
GEAR,JOINT
SPRING,TENSION
SPRING,BRAKE T
SPRING,COUPLING
SPRING,RING
LEVER,LINK 2
LEVER,FLAP
CASS,OPENER
BRACKET,TOP 3V
SCREW,TAP TITE(S) BIND 2.6x8
SCREW,TAP TITE(B) PAN 2.6x6
SCREW,TAP TITE(S) BIND 2.6x4
SCREW,PAN M2x6
SCREW,TAP TITE(B) PAN 2.6x6
SCREW/WASHER(A) M3x4
SCREW/WASHER(A) M2.6x5
POLYSLIDER WASHER 2.6x4.7xT0.13
POLYSLIDER WASHER(CUT) 1.8x4.5xT0.5
E-RING 3.0
CORD JUMPER SMCD-7X151
CORD JUMPER 2Y021902
HEAD (AUDIO CONTROL) HVMXA1072A
HEAD (FULL ERASE) HVFHP0032A
MOTOR (LOADING) MDB2B66
CAPSTAN DD UNIT F2QVB08
MICRO MOTOR I2OAL05
CYLINDER UNIT ASS'Y A2A752B500
R,METAL OXIDE 1.5 OHM 1W
R,METAL OXIDE 560 OHM 1W
R,METAL OXIDE 82K OHM 2W
R,FUSE 0.22 OHM 1W
RC 680 OHM 1/2W
K1-2
Location
No.
C501
C502
C505
C511
C516
C518
C522
C529
D101
D502
D503
D505
D506
D507
D508
D509
D510
D512
D515
D518
D521
D522
D523
D524
D525
D526
D529
D530
D531
D532
D601
D681
D685
D1702
D1703
D1708
D1709
D1710
D1711
D1712
D2601
D2602
D3001
D3002
D4001
D4601
D8001
D8004
D8005
D8006
D8007
D8009
Part No.
LG PART No.
79099006
79099007
79099008
79097757
AD301391
79099012
79097756
79097755
79099033
79099015
79099015
79099015
79099015
79099016
79097747
79097748
79097751
79099019
79099019
AD300075
79099021
AD300075
79099023
79099033
79099025
79099028
79099016
AD300075
79097750
79099021
79099027
79099024
79099024
79097749
79099033
79099031
79099033
79099032
79099025
79099033
79099003
79099003
79099030
79099033
79099025
79099033
79097754
79099032
79099032
79099033
79099033
79099033
E02L03222M
P2472B104M
E02LU2221M
E62QFH101M
CD39E0MQ3M
E02LF1332M
E50HU5100M
E02LT0102M
D1VT001330
D2WTRM11C0
D2WTRM11C0
D2WTRM11C0
D2WTRM11C0
D2WXB290S0
D23T0UG2D0
D2WXGP10K0
D97U02201B
D2LKB340L0
D2LKB340L0
D28TELS6N6
D28TELS2N2
D28TELS6N6
D97U03301B
D1VT001330
D2WXN40050
D97U02401B
D2WXB290S0
D28TELS6N6
D97U01501B
D28TELS2N2
D97U05R11C
0021E5Q210
0021E5Q210
D97U01201B
D1VT001330
D97U01301B
D1VT001330
D97U01001B
D2WXN40050
D1VT001330
DD5R003680
DD5R003680
0010100320
D1VT001330
D2WXN40050
D1VT001330
D97U06R81B
D97U01001B
D97U01001B
D1VT001330
D1VT001330
D1VT001330
Description
CE 2200 UF 25V
CMP 0.1 UF 275V PHE840
CE 220 UF 16V
CE 100 UF 400V
CC 0.0047UF 250V
CE 3300 UF 10V
CE 10 UF 50V
CE 1000 UF 6.3V
DIODE,SILICON 1SS133T-77
DIODE,SILICON RM11C-EIC
DIODE,SILICON RM11C-EIC
DIODE,SILICON RM11C-EIC
DIODE,SILICON RM11C-EIC
DIODE,SILICON SB290S
DIODE,SILICON UG2D-G23, SD-22VE/VL
DIODE,RECTIFIER RGP10K-EIC
DIODE,ZENER MTZJ22B T-77
DIODE,SCHOTTKY SB340L-6737
DIODE,SCHOTTKY SB340L-6737
DIODE,RECTIFIER 10ELS6N-TA1B2
DIODE,RECTIFIER 10ELS2N-TA1B2
DIODE,RECTIFIER 10ELS6N-TA1B2
DIODE,ZENER MTZJ33B T-77
DIODE,SILICON 1SS133T-77
DIODE,SILICON 1N4005-EIC
DIODE,ZENER MTZJ24B T-77
DIODE,SILICON SB290S
DIODE,RECTIFIER 10ELS6N-TA1B2
DIODE,ZENER MTZJ15B T-77
DIODE,RECTIFIER 10ELS2N-TA1B2
DIODE,ZENER MTZJ5.1C T-77
LED LTL-1CHGE-002A
LED LTL-1CHGE-002A
DIODE,ZENER MTZJ12B T-77
DIODE,SILICON 1SS133T-77
DIODE,ZENER MTZJ13B T-77
DIODE,SILICON 1SS133T-77
DIODE,ZENER MTZJ10B T-77
DIODE,SILICON 1N4005-EIC
DIODE,SILICON 1SS133T-77, SD-22VE/VL
DIODE,SILICON 1SS368(TPH3)
DIODE,SILICON 1SS368(TPH3)
INFRARED LED LNA2702L010R
DIODE,SILICON 1SS133T-77
DIODE,SILICON 1N4005-EIC
DIODE,SILICON 1SS133T-77, SD-22VE
DIODE,ZENER MTZJ6.8B T-77
DIODE,ZENER MTZJ10B T-77
DIODE,ZENER MTZJ10B T-77
DIODE,SILICON 1SS133T-77
DIODE,SILICON 1SS133T-77
DIODE,SILICON 1SS133T-77
K1-3
Location
No.
D8010
D8013
D8501
D8502
D8503
D8504
D8505
IC101
IC102
IC501
IC502
IC503
IC601
IC701
IC801
IC1001
IC1002
IC1005
IC1006
IC2001
IC2002
IC2002
IC2601
IC2602
IC2603
IC3001
IC3001
IC3004
IC3005
IC3099
IC3099
IC3099
IC4001
IC4002
IC4003
IC4003
IC4004
IC4004
IC4005
IC4005
IC4006
IC4006
IC4006
IC4501
IC4601
IC8001
IC8002
IC8003
IC8004
IC8501
IC8503
IC8504
Part No.
LG PART No.
79099033
79097752
79099034
79099034
79099034
79099034
79099034
79097760
79097766
79099036
79099037
79099038
79099039
79097762
79097763
79099041
79099042
79099043
79099044
79099045
79099046
79097774
79099047
79099048
79099049
79097768
79097769
79099051
79097767
79097733
79097725
79097741
79099053
79099054
79099055
79040348
79099055
79040348
79099046
79097775
79097770
79097772
79097773
79097764
79097759
79097758
79099058
79097761
79099059
79099060
79099061
79099062
D1VT001330
D97U04R71B
DD5R002260
DD5R002260
DD5R002260
DD5R002260
DD5R002260
I04F38217F
I55F0384FU
I1KJ9A4310
I1KA97809A
0002E00610
I07F529770
I0KF79605H
I0KFA9874A
I55K0251AF
I5HJ001BF0
I55F07S08F
I55F0W2410
I05F094A03
I59J0258B3
ICUJ0256A2
I55F07S04F
I07FV58130
I05FR1323F
I56F57078C
I56F57079D
I9UF032310
I56F07080A
A2A7A1E015
A2A7A0E015
A2A7A2E015
ICQF067320
I5HF96A250
I59J0160FB
ICLJ0610DB
I59J0160FB
ICLJ0610DB
I59J0258B3
ICUJ0256A2
I5QJ0F8325
I5QJ0F8U15
I5QJ0F8V15
I53J4775MA
I03F073580
I03F030260
I0QF02533V
I07F033080
I0QF045800
I55F0H08F0
I1BF019590
I0UFG540A0
Description
DIODE,SILICON 1SS133T-77
DIODE,ZENER MTZJ4.7B T-77, SD-22VE/VL
DIODE,SILICON 1SS226(TE85L)
DIODE,SILICON 1SS226(TE85L)
DIODE,SILICON 1SS226(TE85L)
DIODE,SILICON 1SS226(TE85L)
DIODE,SILICON 1SS226(TE85L)
IC HA118217F
IC TC7SB384FU
IC KIA431
IC KIA7809API
PHOTO COUPLER LTV-817M-VB
IC BU2977FS
IC TDA9605H
IC TDA9874AH
IC OEC6069A
IC S-24C01BFJ-TB
IC TC7S08F-TE85L
IC TC7W241FU-TE12L
IC OEC6068A
IC MSM5416258B-30
IC M11B416256A-25T
IC TC7S04F(TE85L)
IC BA5813FM
IC OEC6067A
IC OEC7078C, SD-22VB
IC OEC7079D, SD-22VE/VL
IC PST3231NR
IC OEC7080A
IC S-24C08ADPA-01, SD-22VB
IC S-24C08ADPA-01, SD-22VE
IC S-24C08ADPA-01, SD-22VL
IC ZR36732
IC S-816A25AMC-BAA-T2
IC MSM56V16160F-8
IC HY57V161610DTC-8
IC MSM56V16160F-8
IC HY57V161610DTC-8
IC MSM5416258B-30
IC M11B416256A-25T
IC MBM29F800BA-55PFTN-SFK-32, SD-22VB
IC MBM29F800BA-55PFTN-SFK-U1, SD-22VE
IC MBM29F800BA-55PFTN-SFK-V1, SD-22VL
IC LC74775M-9839
IC LA7358M, SD-22VE
IC LA73026V
IC NJN2533V(TE2), SD-22VE/VL
IC BA3308F, SD-22VB/VL
IC NJM4580M
IC TC7SH08FU(TE85L)
IC AD1959YRSRL
IC MM1540AFBE
K1-4
Location
No.
Q101
Q102
Q103
Q104
Q105
Q106
Q107
Q108
Q109
Q110
Q111
Q111
Q112
Q113
Q501
Q502
Q504
Q505
Q506
Q601
Q651
Q652
Q1003
Q1004
Q1701
Q1702
Q1703
Q1705
Q1705
Q1706
Q1707
Q1707
Q1708
Q1709
Q1711
Q1712
Q1713
Q1714
Q2001
Q2601
Q2602
Q2603
Q2604
Q2605
Q3001
Q3002
Q3003
Q3004
Q3005
Q3006
Q3007
Q3008
Part No.
LG PART No.
79099065
79099065
79097793
79099065
79099064
79099063
79099063
79097793
79099069
79097793
79099099
79099068
79097796
79097793
79097790
79099065
79097791
79099073
79099074
79099063
79099064
79099075
79099086
79099086
79099065
79099073
79099073
79099099
79099068
79097791
79099099
79099068
79099073
79099069
79099069
79099073
79099087
79099069
79099088
79099089
79099090
79099091
79099091
79099092
79097377
79097377
79099069
79099094
79099094
79099093
79099093
79099069
TCAT032034
TCAT032034
TNYJA05001
TCAT032034
TPAAC05002
TCATC31980
TCATC31980
TNYJA05001
TNAAC05002
TNYJA05001
TCAA3875SY
T8YJ2412K0
TPATC03002
TNYJA05001
T410K26470
TCAT032034
TAAT01241Y
TCAT03209Y
TNATA03002
TCATC31980
TPAAC05002
TPAAB05001
TPYJB05001
TPYJB05001
TCAT032034
TCAT03209Y
TCAT03209Y
TCAA3875SY
T8YJ2412K0
TAAT01241Y
TCAA3875SY
T8YJ2412K0
TCAT03209Y
TNAAC05002
TNAAC05002
TCAT03209Y
TAAT012714
TNAAC05002
T85A03326B
TNAAB05003
TS5M000037
TS5M000036
TS5M000036
T65A01213Y
0000M00390
0000M00390
TNAAC05002
0002700680
0002700680
0002700690
0002700690
TNAAC05002
Description
TRANSISTOR,SILICON KTC3203_Y-AT, SD-22VE/VL
TRANSISTOR,SILICON KTC3203_Y-AT
COMPOUND TRANSISTOR DTC143EKAT146, SD-VE/VL
TRANSISTOR,SILICON KTC3203_Y-AT
COMPOUND TRANSISTOR KRA103SRTK
TRANSISTOR,SILICON KTC3198-AT(Y,GR)
TRANSISTOR,SILICON KTC3198-AT(Y,GR)
COMPOUND TRANSISTOR DTC143EKAT146
COMPOUND TRANSISTOR KRA103SRTK, SD-22VE
COMPOUND TRANSISTOR DTC143EKAT146
TRANSISTOR,SILICON
KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
COMPOUND TRANSISTOR KRA103MAT, SD-22VE
COMPOUND TRANSISTOR DTC143EKAT146
FET 2SK2647-01MR
TRANSISTOR,SILICON KTC3203_Y-AT
TRANSISTOR,SILICON KTA1241_Y-AT
TRANSISTOR,SILICON KTC3209_Y-AT
COMPOUND TRANSISTOR KRC101MAT
TRANSISTOR,SILICON KTC3198-AT(Y,GR)
COMPOUND TRANSISTOR KRA103SRTK
COMPOUND TRANSISTOR KRA102SRTK
COMPOUND TRANSISTOR DTA114EKAT146
COMPOUND TRANSISTOR DTA114EKAT146
TRANSISTOR,SILICON KTC3203_Y-AT
TRANSISTOR,SILICON KTC3209_Y-AT
TRANSISTOR,SILICON KTC3209_Y-AT
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
TRANSISTOR,SILICON KTA1241_Y-AT
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
TRANSISTOR,SILICON KTC3209_Y-AT
COMPOUND TRANSISTOR KRC103SRTK
COMPOUND TRANSISTOR KRC103SRTK
TRANSISTOR,SILICON KTC3209_Y-AT
TRANSISTOR,SILICON KTA1271_Y-AT
COMPOUND TRANSISTOR KRC103SRTK
TRANSISTOR,SILICON 2SC3326_B(TE85L)
COMPOUND TRANSISTOR KRC102SRTK
COMPOUND TRANSISTOR HN1C03F_B(TE85L)
COMPOUND TRANSISTOR HN1B01F_Y(TE85L)
COMPOUND TRANSISTOR HN1B01F_Y(TE85L)
TRANSISTOR,SILICON 2SA1213_Y(TE12L,C)
PHOTO TRANSISTOR ST-304L
PHOTO TRANSISTOR ST-304L
COMPOUND TRANSISTOR KRC103SRTK
PHOTO COUPLER RPI-352C40N
PHOTO COUPLER RPI-352C40N
PHOTO COUPLER RPI-303
PHOTO COUPLER RPI-303
COMPOUND TRANSISTOR KRC103SRTK, SD-22VB/VE/VL
K1-5
Location
No.
Q3009
Q4001
Q4501
Q4501
Q4601
Q4602
Q4603
Q4604
Q4605
Q4606
Q8001
Q8001
Q8002
Q8002
Q8003
Q8004
Q8005
Q8005
Q8006
Q8006
Q8012
Q8013
Q8014
Q8014
Q8015
Q8015
Q8501
Q8502
Q8503
Q8505
Q8507
Q8508
Q8509
Q8510
Q8511
Q8512
Q8513
L501
L503
T501
J601
J602
J603
J8001
J8002
J8003
J8005
SW601
SW602
SW603
SW604
SW605
Part No.
LG PART No.
79099069
79099092
79099098
79099067
79099099
79099098
79099099
79099069
79099099
79099099
79099098
79099067
79099099
79099068
79097795
79099075
79097792
79097873
79099099
79099068
79099069
79099097
79099099
79099068
79099099
79099068
79099098
79099098
79099098
79099098
79097794
79099090
79099099
79099075
79099075
79099088
79099088
79097384
79099101
79097385
79099103
79099103
79099104
79099108
79099110
79099107
79097387
79099112
79099112
79099112
79099112
79099112
TNAAC05002
T65A01213Y
TAAA1504SY
T6YJ1037K0
TCAA3875SY
TAAA1504SY
TCAA3875SY
TNAAC05002
TCAA3875SY
TCAA3875SY
TAAA1504SY
T6YJ1037K0
TCAA3875SY
T8YJ2412K0
TNYJD05001
TPAAB05001
TCATC3199Y
TCYT1740S0
TCAA3875SY
T8YJ2412K0
TNAAC05002
TPAAA05001
TCAA3875SY
T8YJ2412K0
TCAA3875SY
T8YJ2412K0
TAAA1504SY
TAAA1504SY
TAAA1504SY
TAAA1504SY
TNYJB05001
TS5M000037
TCAA3875SY
TPAAB05001
TPAAB05001
T85A03326B
T85A03326B
029T000083
02167E220K
048129102S
060Q401086
060Q401086
060Q421024
060J401082
060J411020
063D700005
063G000072
0504201T32
0504201T32
0504201T32
0504201T32
0504201T32
Description
COMPOUND TRANSISTOR KRC103SRTK, SD-22VB/VE/VL
TRANSISTOR,SILICON 2SA1213_Y(TE12L,C)
TRANSISTOR,SILICON KTA1504S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON 2SA1037AKT146R,S, SD-22VL
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VE
TRANSISTOR,SILICON KTA1504S_Y_RTK, SD-22VE
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VE
COMPOUND TRANSISTOR KRC103SRTK, SD-22VE
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VE
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VE
TRANSISTOR,SILICON KTA1504S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON 2SA1037AKT146R,S, SD-22VL
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
COMPOUND TRANSISTOR DTC144EKAT146, SD-22VB/VE/VL
COMPOUND TRANSISTOR KRA102SRTK
TRANSISTOR,SILICON KTC3199_Y-AT, SD-22VB
TRANSISTOR,SILICON 2SC1740SP TP, SD-22VL
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
COMPOUND TRANSISTOR KRC103SRTK
COMPOUND TRANSISTOR KRA101SRTK
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
TRANSISTOR,SILICON KTC3875S_Y_RTK, SD-22VB/VE
TRANSISTOR,SILICON
2SC2412KT146 R,S, SD-22VL
TRANSISTOR,SILICON KTA1504S_Y_RTK
TRANSISTOR,SILICON KTA1504S_Y_RTK
TRANSISTOR,SILICON KTA1504S_Y_RTK
TRANSISTOR,SILICON KTA1504S_Y_RTK
COMPOUND TRANSISTOR DTC114EKAT146
COMPOUND TRANSISTOR HN1C03F_B(TE85L)
TRANSISTOR,SILICON KTC3875S_Y_RTK
COMPOUND TRANSISTOR KRA102SRTK
COMPOUND TRANSISTOR KRA102SRTK
TRANSISTOR,SILICON 2SC3326_B(TE85L)
TRANSISTOR,SILICON 2SC3326_B(TE85L)
COIL,LINE FILTER 0R3A433F20
COIL 22 UH
TRANSFORMER,SWITCHING
8129102S
RCA JACK AV1-06DG-1
RCA JACK AV1-06DG-1
RCA JACK AV1-06DSG-1
RCA JACK MSP-251V-05PBSN
RCA JACK MSP-242V2-01PBSN
JACK MDC-070V
SOCKET,21PIN 035_0_8183_00
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
K1-6
Location
No.
SW681
SW682
SW684
SW686
SW687
SW688
SW689
SW3001
SW3001
PCB010
PCB010
PCB010
PCB130
PCB130
PCB240
PCB240
PCB270
PCB270
PCB270
PCB280
PCB280
PCB280
PCB390
PCB390
PCB390
CD102
CD102
CD501
CD501
CD502
CD601
CD651
CD652
CP102
CP502
CP503
CP601
CP651
CP653
CP681
CD2601
CD2603
CD6002
CD8002
CD8501
CD8502
CP1701
CP2601
CP2602
CP2603
CP3001
CP8001
Part No.
LG PART No.
79099112
79099112
79099112
79099112
79099112
79099112
79099112
79097386
79099113
79097732
79097724
79097740
79097734
79097742
79097735
79097726
79097736
79097727
79097743
79097737
79097728
79097744
79097738
79097729
79097745
79099120
79097703
79097599
79097597
79099122
79097389
79099123
79099124
79099126
79099128
79099129
79099130
79099132
79099131
79099133
79099134
79099135
79097388
79099138
79099139
79099140
79099141
79099142
79099143
79099126
79099011
79099144
0504201T32
0504201T32
0504201T32
0504201T32
0504201T32
0504201T32
0504201T32
0508S11001
0508A11001
A2A7A1E010
A2A7A0E010
A2A7A2E010
A2A7A1E130
A2A7A2E130
A2A7A1E240
A2A7A0E240
A2A7A1E270
A2A7A0E270
A2A7A2E270
A2A7A1E280
A2A7A0E280
A2A7A2E280
A2A7A1E390
A2A7A0E390
A2A7A2E390
122F061502
122F061501
120G639803
1206459801
122Y0G1701
06CDVA5003
122H072402
122S0I0802
069J760029
067U016019
069S260629
069R7I0479
069J7I0029
069J770019
069R770479
122H081006
122H060806
06CDL02003
122H0I1801
06CU2D3001
06CU262501
069R2G0589
069EV8T020
069EVNT020
069J760029
06972C0010
069S2D0629
Description
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH,TACT SKQNAED010
SWITCH (LEAF) LSA-1144EAU, SD-22VB
SWITCH (LEAF) MXS01350MVP0, SD-22VL
PCB ASS'Y VMB252A, SD-22VB
PCB ASS'Y VMB252A, SD-22VE
PCB ASS'Y VMB252A, SD-22VL
PCB ASS'Y VMA249B, SD-22VB/VE
PCB ASS'Y VMA249B, SD-22VL
PCB ASS'Y VPA152B, SD-22VB
PCB ASS'Y VPA152B, SD-22VE/VL
PCB ASS'Y VEA978A, SD-22VB
PCB ASS'Y VEA978A, SD-22VE
PCB ASS'Y VEA978A, SD-22VL
PCB ASS'Y VEA979A, SD-22VB
PCB ASS'Y VEA979A, SD-22VE
PCB ASS'Y VEA979A, SD-22VL
PCB ASS'Y VEA972A, SD-22VB
PCB ASS'Y VEA972A, SD-22VE
PCB ASS'Y VEA972A, SD-22VL
CORD,JUMPER 2F061502, SD-22VB/VE
CORD,JUMPER 2F061501, SD-22VL
CORD,AC BUSH 0G639803, SD-22VB
CORD,AC BUSH 06459801, SD-22VE/VL
CORD,JUMPER 2Y0G1701
CABLE,21PIN S-1002B, SD-22VE
CORD,JUMPER 2H072402
CORD,JUMPER 2S0I0802
CONNECTOR PCB SIDE
IMSA-9604S-06Z14
WIRE HOLDER B2013H02-16P
CONNECTOR PCB SIDE A2001WV2-6P
CONNECTOR PCB SIDE 52492-1820
CONNECTOR PCB SIDE IMSA-9604S-18Z14
CONNECTOR PCB SIDE IMSA-9604S-07Z13
CONNECTOR PCB SIDE 52492-0720
CORD,JUMPER 2H081006
CORD,JUMPER 2H060806
CABLE,PAL CDL02003
CORD,JUMPER 2H0I1801
CORD,CONNECTOR CU2D3001
CORD,CONNECTOR CU262501
CONNECTOR PCB SIDE 52147-1610
CONNECTOR PCB SIDE 04_6232_108_015
CONNECTOR PCB SIDE 04_6232_123_015
CONNECTOR PCB SIDE IMSA-9604S-06Z14
CONNECTOR PCB SIDE TMC-J12P-B2
CONNECTOR PCB SIDE A2001WV2-13P
K1-7
Location
No.
CP8002
CP8502
CUS011
CUS131
CUS811
DK4001
DK4001
DK4001
EL001
EL002
F501
F501
OS601
OS8001
TM601
TM601
TU301
TU301
TU301
V601
X101
X801
X1001
X3001
X3002
X3003
X8501
Part No.
LG PART No.
79099145
79099145
79097711
79099146
79099146
79097707
79097708
79099147
79097705
79097704
79097394
79097395
79099149
79099150
79097391
79097392
79097381
79097383
79097382
79097396
79097596
79097399
79099155
79099157
79097398
79097397
79099159
069J7I0019
069J7I0019
800WFAA008
800WFAA006
800WFAA006
169J00017A
169J00018A
169J00010A
124120301A
124116281A
080NT04003
080NT04004
077Q037002
07A9000004
076D0FW010
076D0FW020
0162K01022
0162K17001
0162K01029
096F90R403
100CT4R407
100CT02401
1002T00901
100DA32R01
100CT01207
1001T4R010
100WT02706
Description
CONNECTOR PCB SIDE IMSA-9604S-18Z13
CONNECTOR PCB SIDE IMSA-9604S-18Z13
CUSHION C
CUSHION A, SD-22VB/VE/VL
CUSHION A
DECK CD TU2120R
DECK CD TU2320R
DECK CD TU2020R
EYE LET XRY20X30BD
EYE LET XRY16X28BD
FUSE 50T040HCC, SD-22VB
FUSE 50T040H, SD-22VE/VL
REMOTE RECEIVER PIC-37143TH5
OPTICAL DEVICE GP1FA550TZ
TRANSMITTER ORV202N33010, SD-22VB
TRANSMITTER ORV202N33020, SD-22VE/VL
RF UNIT TCMI0600PD08D, SD-22VB
RF UNIT TCPL0601PD08D, SD-22VE
RF UNIT TCMB0601PD13D, SD-22VL
TUBE FLUORSCENT DISPLAY
HNV-09SS33
CRYSTAL HC-49/U
CRYSTAL HC-49/U
CERAMIC OSCILLATOR CSTCC9M00G53-R0
CRYSTAL DT-26
CRYSTAL HC-49/U-S
CERAMIC OSCILLATOR EFOMC4004T4
CRYSTAL HC-49/U-S
K1-8
FILE NO. 810-200213
SERVICE MANUAL
TM
DVD VIDEO PLAYER & VIDEO
CASSETTE RECORDER
SD-22VB
SD-22VE
SD-22VL
OCT., 2002
DVD BLOCK DIAGRAM
B
B
X8501
27MHz
A
VCR BLOCK
PUDET2,LSRDVD
E
DACSOX,DACDATA,DACCLK
AUDIO_DAC
IC8503
AD1959YRSRL
C
/BWL,/BWU,/BCAS
/BRAS,/BDE
RF OUT
A+3V
D-RAM
IC2002
MSM5416258B-30
2.5V REG.
IC4002
S-816A25AMC
MMPEG+1.8V
RF_AMP
IC2603
OEC6067A
DPD 0~15
DPA 0~7
RF,FO,EO,AO
DO,CO,BO
LDMP,LDMN
FMN,FMP,DMN,DMP
F+,T-,T+,F-
LMT,TOPN,TCLS
DECK
DK4001
TT-4000
(TU2020R)
AUDIO OUT L
AUDIO OUT R
ZERO
ABCLK,ALRCLK,ASDATA 0
SCLK 2
GCLK
GCLK 1
MOTOR
DRIVER
IC2602
BA5813FM
A, C
B, F
DVD DAT 0~7
DVDSTB,VALID,SOS,ERR
DSP
IC2001
OEC6068A
D
DVD OUT
MPEG
IC4001
ZR36732
VIDEO_DRIVER
IC8504
MM1540AFBE
DAC,A,B,C,D
HD 0~15
C
LDMN,LDMP
HA 1~4
SCL,SDA,WP
SD-RAM
IC4004
MSM56V16160F-8
MPGCS#,MPGIRQ,I45RSTX
MICON
IC1001
OEC6069A
A
A
HA 1~19
HA 1~8
LCAS,UCAS
OE,WE,RAS
FLASHCS
D-RAM
IC4005
MSM5416258B-30
F-1
MWR,MRD
FLASH
IC4006
MBM29F800BA-55
MCSO#,MRAS#,MCAS#,MWE#,MDQM
C
MA 0~11
HA 8
MWR
MRD
MD 0~15
V_SYNC
CONTROL
IC1006
TC7W241FU
DISKWD1
FCSEAR
SVCEX
SPDIF-134
RESET
A
DVD R
DVD G
DVD B
DVD RESET
TX,RX
SD-RAM
IC4003
MSM56V16160F-8
C
MPCLK
HD 0~15
A
A---P.CON+D5V
B---P.CON+5V A
C---P.CON+3.3V
D---P.CON+9V
E---P.CON+5V D
F---P.CON+9V A
F-2
IC102
TC7SB384FU
Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM
(SD-22VB)
SINGLE SW IC
2
CP101
9
HF1 (R)
8
HF_COM
7
HF2 (L)
89
6
SP-CH1 (R)
88
5
SP_COM
87
79
4
SP-CH2 (L)
86
3
EP/LP-CH1 (R)
94
2
EP/LP_COM
92
1
EP/LP-CH2 (L)
93
HF2
91
TUNER/JACK/
HI-FI/21PIN/OSD
75
78
X TAL VCO/OSD
73
60
58
VCA
CTL TRAP
FH HPF
ACC
R
6db AMP
P
DELAY
CLPF
CLPF
R
TRAP
HPF
MICON
IIC_DATA
63
V. H_SW
81
ENV. DET
84
R
MAIN
CONV1
P
C SQUELCH
MAIN
CONV2
R
R
N
P
REC
MUTE
B.D
SQUELCH
BPF
VIDEO ALC
ENV
DET
P
HPF
MIX
LEVELADJ
NA_REC-H
FBC
R
B.E
C.K
46
P
1
FE HEAD (GND)
2
FE HEAD (HOT)
SQPB
629
TRAP
FM AGC
P.EQ
C CCD
S DL
G EQ
NL EMPH
R
NL DE EMPH
P
R
1M HPF
SQPB
D LIM
CP102
1
AE HEAD (–)
2
AE HEAD (+)
5
AUDIO REC
P
PRE
AMP
Q105,Q106,
Q107
6
CLEAR
SYNC
P
LPF
CP103
HEAD AUDIO
CONTROL
6db AMP
C.K
R
P
62
51
CCD
LPF
P
HF_COM
IIC_CLK
52
54
55
CR DET 2FSC
2MLPF
HF1
Q111
AMP
P
H.AMP
CYL
5
X101
4.433619MHz
REC
EQ
PB SW
3
Q102
NORMAL A.
REC ST SW
1
6
ATT
P
28
FO/DEV ADJ
YLPF
MAIN EMPH
CARRIER
OFFSET
W.C/DC
R
P
3
VIDEO
AGC
R
D.E
N.C
5
YNP
CLAMP
CLAMP
LPF
4
ATT
NORMAL_A_IN
9
SWD_VIDEO
39
R
P
MAIN
DE-EMPH
4
69
NORMAL_A_OUT
LAG LEAD
LPF
S-DET
2FSC
TUNER/JACK/
HI-FI/21PIN/OSD
DEMO
SLPF
Y CCD
Y APA
COIL, BIAS OSC
L104
OSC
FBC
ALC
FM MOD
AUDIO PB
Q104
42
7M LPM
VCA
R
35
11
LINE
AMP
Y/C/AUDIO/CCD/HEAD AMP IC
IC101 HA118217F
ATT
BAND
GAP
6
18
19
21
23
24
26
30
31
EE/VV_V_OUT
TU_V_OUT
F-3
MICON
DUMMY_V. SYNC
OPERATION/
DISPLAY
FRONT_V_IN
E-4
Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM
(SD-22VE)
SECAM CHROMA
IC4601 LA7358M
VV-H
MICON
SECAM_H
SYNC
SP-H
AGC
AMP
14
CP103
FE HEAD (HOT)
1
FE HEAD (GND)
1.1MHz
BPF
1
9
4
29
PB
ON
SINGLE SW IC
2
5
Q112
P.CON SW
Q111
B
AMP
Q4603
VV SW
PB SW
BUFFER
FE OSC
Fo
ADJ
Q4604
Q4606
Q101
1.1MHz
OSC
11
PB
MUTE
REC/
PB
IC102
TC7SB384FU
SYNC GATE
GEN / V-SEP
B
IREF
12
PB
MUTE
VA
Fo
ADJ
CONTROL
LOGIC
VA
REC
ON
3
4
4.43MHz
OSC
MODE
CTL
PB
B
1
2
28
REC
SYNC
GATE
REC
MUTE
FE OSC COIL
L101
MICON
SECAM_IN
22
17
18
16
Q109
2
SECAM SW
Q4605
Q4602
SECAM PB
VV SW
Q103
9
HF1 (R)
8
HF_COM
7
HF2 (L)
89
6
SP-CH1 (R)
88
79
SP_COM
5
SP-CH2 (L)
86
3
EP/LP-CH1 (R)
94
2
EP/LP_COM
92
1
EP/LP-CH2 (L)
93
HF2
91
60
73
P
2MLPF
ACC
6db AMP
DELAY
CLPF
CLPF
R
HPF
R
P
IIC_CLK
62
63
V. H_SW
81
ENV. DET
84
REC
MUTE
AUDIO REC
6
AUDIO PB
P
CLEAR
SYNC
P
B.D
SQUELCH
BPF
VIDEO ALC
ENV
DET
P
HPF
MIX
LEVELADJ
FBC
R
B.E
C.K
DUMMY_V. SYNC
PICTURE_CTL
17
SQPB
FM AGC
P.EQ
S DL
G EQ
1M HPF
P
PRE
AMP
SQPB
3
REC
EQ
1
6
3
4
FO/DEV ADJ
69
NORMAL_A_IN
9
11
35
42
39
16
R
P
P
ATT
Y APA
YLPF
MAIN EMPH
CARRIER
OFFSET
W.C/DC
R
COMPOUND
28
FRONT_V_IN
CLAMP
LPF
ATT
18
Q108, Q110
YNR
P
BAND
GAP
6
COMPOUND
VIDEO
AGC
R
D.E
N.C
CLAMP
LINE
AMP
Q113
Y CCD
FBC
ALC
FM MOD
4
2FSC
C CCD
14
MAIN
DE-EMPH
S-DET
NORMAL_A_OUT
P
DEMO
SLPF
5
Q102
NORMAL A.
REC ST SW
NL DE EMPH
7M LPM
LAG LEAD
LPF
COIL, BIAS OSC
L104
OSC
R
D LIM
VCA
R
Q104
NL EMPH
MICON
S.DET-H
46
R
PB SW
5
R
R
N
P
CP102
AE HEAD (+)
MAIN
CONV1
P
C SQUELCH
MAIN
CONV2
LPF
Q105,Q106,
Q107
2
6db AMP
C.K
TRAP
629
TRAP
TUNER/JACK/
HI-FI/21PIN/OSD
CCD
LPF
P
R
P
V.REC_ST-H
NA_REC-H
AC HEAD
CTL TRAP
FH HPF
R
51
52
54
55
SYNC.SEP
CR DET 2FSC
HF_COM
IIC_DATA
58
50
VCA
HF1
MICON
Q4601
BUFFER
X TAL VCO/OSD
87
4
TUNER/JACK/
HI-FI/21PIN/OSD
75
78
H.AMP
CYL
X4001
4.433619MHz
V.REC_ST_SW
CP101
19
21
23
24
26
30
OPERATION/
DISPLAY
ATT
31
TU_V_OUT
TUNER/JACK/
EE/VV_V_OUT HIFI/21PIN/
OSD
SWD_VIDEO
Y/C/AUDIO/CCD/HEAD AMP IC
IC101 HA118217F
F-5
F-6
Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM
(SD-22VL)
IC102
TC7SB384FU
SINGLE SW IC
2
CP101
9
HF1 (R)
8
HF_COM
7
HF2 (L)
89
6
SP-CH1 (R)
88
5
SP_COM
87
79
4
SP-CH2 (L)
86
3
EP/LP-CH1 (R)
94
2
EP/LP_COM
92
1
EP/LP-CH2 (L)
93
HF2
91
TUNER/JACK/
HI-FI/21PIN/OSD
75
78
X TAL VCO/OSD
60
58
VCA
CTL TRAP
FH HPF
62
IIC_DATA
63
V. H_SW
81
ENV. DET
84
NA_REC-H
V.REC_ST_H
Q103
V.REC_ST_SW
FE OSC COIL
L101
Q101
FE OSC
1
4
ACC
R
6db AMP
DELAY
CLPF
CLPF
R
TRAP
HPF
FE HEAD (GND)
1
FE HEAD (HOT)
R
5
AUDIO REC
6
ENV
DET
P
PRE
AMP
P.EQ
C CCD
S DL
G EQ
SQPB
NL EMPH
R
NL DE EMPH
P
REC
EQ
FBC
ALC
DEMO
SLPF
LAG LEAD
LPF
35
42
7M LPM
VCA
R
Y CCD
39
R
P
MAIN
DE-EMPH
ATT
P
FM MOD
28
Y APA
FO/DEV ADJ
1
6
S-DET
YLPF
MAIN EMPH
CARRIER
OFFSET
W.C/DC
R
P
5
3
VIDEO
AGC
R
D.E
N.C
4
YNP
CLAMP
CLAMP
LPF
4
ATT
NORMAL_A_IN
9
SWD_VIDEO
FM AGC
1M HPF
69
NORMAL_A_OUT
46
SQPB
R
2FSC
TUNER/JACK/
HI-FI/21PIN/OSD
VIDEO ALC
R
B.E
C.K
50
FBC
BPF
MIX
LEVELADJ
3
Q102
NORMAL A.
REC ST SW
SQUELCH
P
HPF
COIL, BIAS OSC
L104
OSC
B.D
P
D LIM
AUDIO PB
Q104
CLEAR
SYNC
P
SYNC SEP
REC
MUTE
629
TRAP
PB SW
AE HEAD (+)
R
R
N
P
Q105,Q106,
Q107
2
MAIN
CONV1
P
C SQUELCH
MAIN
CONV2
LPF
3
CP101
6db AMP
C.K
R
P
CP103
2
51
CCD
LPF
P
P
IIC_CLK
52
54
55
CR DET 2FSC
HF_COM
MICON
HEAD AUDIO
CONTROL
73
2MLPF
HF1
Q111
AMP
P
H.AMP
CYL
5
X101
4.433619MHz
4
11
LINE
AMP
Y/C/AUDIO/HEAD AMP IC
IC101 HA118217F
ATT
BAND
GAP
6
18
19
21
23
24
26
30
31
EE/VV_V_OUT
TU_V_OUT
MICON
F-7
OPERATION/
DISPLAY
DUMMY_V. SYNC
SYNC
FRONT_V_IN
F-8
MICON BLOCK DIAGRAM
(SD-22VB)
P. CON + 5V
REEL SENS
Q3007
2
1
2
SYSCON/SOFTWARE/SERVO IC
IC3001 OEC7078C
1
REEL SENS
Q3006
4
3
4
IIC_CLK
79 REEL-S
3
IIC_DATA
TUNER/JACK/
HI-FI/21PIN/OSD
80 REEL-T
X3001
32.768KHz
IC3004
PST3231NR
SYSTEM
RESET IC
41 XC IN
42 XC OUT
43 RESET
1
SW3001
X3002
12MHz
Q3009
FF/REW SW
FF/REW SW
38 X IN
KEY-A
KEY-A
KEY-B
4
KEY-B
IIC-SDA 72
5
IIC-CLK 71
6
IIC_DATA
81 TAB_SW
IIC_CLK
8
97
CTL AMP OUT
V. ENV
93
CTL SW OUT
VH SW 18
ENV. DET
V. H_SW
NA_REC-H 29
MS_SEN B
OPERATION/
DISPLAY
EEP ROM IC
IC3099
S-24C08ADPA-01
FF/REW-L
Q3004
AT + 5.2V
REM_IN
3
39 X OUT
25
Q3008
REMOCON 14
Y/C/AUDIO/
HEAD AMP
NA_REC-H
1
MSSW_B
D.V.SYNC 13
2
MSSW_A
CG-CLK 70
CG_CLK
CG_CS 69
CG_CS
DUMMY_V.SYNC
Q3005
D3001
MS_SEN A
Q3003
CENT SW
DVD_POWER_A
REGULATOR
POWER_FAIL
21 CENT LED
31 DVD_POWER_A
CG_CLK
CG_DATA
Q3001
BOT SENSOR
SUB_CLK
SUB DATA IN
SUB/MICON/
OSD/VPS
SUB DATA OUT
SUB RESET
TUNER/JACK/
HI-FI/21PIN/OSD
OPERATION/
DISPLAY
FL_CS
FL_CS 27
10 BOT
Q3002
EOT SENSOR
CG_DATA
82 P. FAIL
20 POWER ON-H A
VCR_POWER_ON_H
CG-DATA 68
LDM CTL 47
6 EOT
67 SUB_CLK
66 SUB DATA IN
DFG 87
65 SUB DATA OUT
49 SUB RESET
CYL CTL 78
DVD_MUTE 28
CAP_FG 1
CAP/M/F/R 4
I_LIMIT 5
CAP_CTL 9
LDM_CTL 10
CYL_FG/PG 11
CYL_CTL 12
CP3001
DVD MUTE
DVD IN/OUT
DVD_RESET 17
OPERATION/
DISPLAY
SEG10
DVD_RESET
59 SEG 10
CAP_FWD 11
CFG 85
CAP CTL 77
CAP_LIMIT 12
SUB CS. 46
F-9
SUB_CS
SUB MICON/
OSD/VPS
F-10
MICON BLOCK DIAGRAM
(SD-22VE, SD-22VL)
P. CON + 5V
REEL SENS
Q3007
2
1
2
SYSCON/SOFTWARE/SERVO IC
IC3001 OEC7079D
1
REEL SENS
Q3006
4
3
4
IIC_CLK
79 REEL-S
3
IIC_DATA
TUNER/JACK/
HI-FI/21PIN/OSD
80 REEL-T
X3001
32.768KHz
IC3004
PST3231NR
SYSTEM
RESET IC
42 XC OUT
43 RESET
1
SW3001
X3002
12MHz
Q3009
FF/REW SW
FF/REW SW
AT + 5.2V
MS_SEN B
D3001
41 XC IN
MS_SEN A
38 X IN
Q3004
Q3005
DVD_POWER_A
KEY-A
KEY-B
4
KEY-B
IIC-SDA 72
5
IIC-CLK 71
6
IIC_DATA
81 TAB_SW
IIC_CLK
8
97
CTL AMP OUT
V. ENV
93
CTL SW OUT
VH SW 18
1
MSSW_B
2
MSSW_A
21 CENT LED
20 POWER ON-H A
Q3001
BOT SENSOR
EOT SENSOR
SUB_CLK
SUB DATA IN
SUB DATA OUT
SUB RESET
NA_REC-H
D.V.SYNC 13
DUMMY_V.SYNC
CG-CLK 70
CG_CLK
CG_CS 69
CG_CS
CG-DATA 68
CG_DATA
10 BOT
CG_DATA
FL_CS 27
FL_CS
SEG10 59
SEG10
LDM CTL 47
6 EOT
67 SUB_CLK
66 SUB DATA IN
VV-H
DFG 87
65 SUB DATA OUT
49 SUB RESET
SECAM_H
SYNC
SP-H
SECAM_IN
PICTURE_CTL
S.DET-H
30 VV-H
23 SECAM_H
Y/C/AUDIO/
HEAD AMP
TUNER/JACK/
HI-FI/21PIN/OSD
CG_CLK
CYL CTL 78
Y/C/AUDIO/
HEAD AMP
V. H_SW
NA_REC-H 29
Q3002
SUB/MICON/
OSD/VPS
ENV. DET
82 P. FAIL
VCR_POWER_ON_H
OPERATION/
DISPLAY
EEP ROM IC
IC3099
S-24C08ADPA-01
31 DVD_POWER_A
POWER_FAIL
REGULATOR
KEY-A
FF/REW-L
Q3003
CENT SW
REM_IN
3
39 X OUT
25
Q3008
REMOCON 14
DVD_MUTE 28
OPERATION/
DISPLAY
CAP_FG 1
CAP/M/F/R 4
I_LIMIT 5
CAP_CTL 9
LDM_CTL 10
CYL_FG/PG 11
CYL_CTL 12
CP3001
DVD MUTE
DVD IN/OUT
DVD_RESET 17
DVD_RESET
84 C.SYNC
24 SP-H
15 SECAM_IN
76 PICTURE_CTL
16 S.DET-H
CAP_FWD 11
CFG 85
CAP CTL 77
CAP_LIMIT 12
SUB CS. 46
F-11
SUB_CS
SUB MICON/
OSD/VPS
F-12
REGULATOR BLOCK DIAGRAM
(SD-22VB)
CAP_VCO
AT+5V[M-CON]
AT+12.6V
MICON
MOTOR_GND
Q1703
P.CON 5V SW.
Q1702
P.CON 5V SW.
Q1713
M-CON + 5V SW.
-22V
HEATER_DC-
Q1714
M-CON POWER
SW.
OPERATION/
DISPLAY
HEATER_DC+
Q1709, Q1711
P.CON SW.
CP1701
1
POWER
Q1712
NC
2
MOTOR +12V
3
MOTOR GND
4
AT +13V
5
AT 5.2V
6
AT 5.2V
7
UNREG 3.3V
8
UNREG 3.3V
9
POWER ON H
10
GND
11
GND
12
P.FAIL
13
14
TUNER 32V
15
HEATER_DC-
16
HEATER_DC+
P.CON +9V SW.
Q1708
P.CON +12V SW.
Q1701
12V REG
VCR POWER ON-H
MICON
POWER FAIL
DVD_POWER_A
-22V
Q1705
3.3V CTL
P.CON+12V
Q1707
AT+5.2V
3.3V CTL
P.CON+5V DH
3.3V OUT
Q1706
DVD IN/OUT
P.CON+3.3V
P.CON+9V
P.CON+5V
+32V
TUNER/JACK/HI-FI/
21PIN/OSD
AT+12V
F-13
F-14
REGULATOR BLOCK DIAGRAM
(SD-22VE, SD-22VL)
CAP_VCO
AT+5V[M-CON]
AT+12.6V
MICON
MOTOR_GND
Q1703
P.CON 5V SW.
Q1702
P.CON 5V SW.
Q1713
M-CON + 5V SW.
-22V
HEATER_DC-
Q1714
M-CON POWER
SW.
OPERATION/
DISPLAY
HEATER_DC+
Q1709, Q1711
P.CON SW.
CP1701
1
MOTOR +24V
POWER
2
MOTOR +12V
3
MOTOR GND
4
AT +13V
5
AT 5.2V
6
AT 5.2V
7
UNREG 3.3V
8
UNREG 3.3V
9
POWER ON H
10
GND
11
GND
12
P.FAIL
13
14
Q1712
P.CON +9V SW.
Q1708
P.CON +12V
SW.
Q1701
12V REG
VCR POWER ON-H
MICON
POWER FAIL
TUNER 32V
DVD_POWER_A
-22V
15
HEATER -
16
HEATER +
Q1705
3.3V CTL
P.CON+12V
Q1707
AT+5.2V
3.3V CTL
P.CON+5V DH
3.3V OUT
Q1706
DVD IN/OUT
P.CON+3.3V
P.CON+9V
P.CON+5V
+32V
TUNER/JACK/HI-FI/
21PIN/OSD
AT+12V
F-15
F-16
OPERATION/DISPLAY BLOCK DIAGRAM
V601
HNV-09SS33
32 12 11 10
24 25
4
2
1 34 35
HEATER_DC+
HEATER_DC-
REGULATOR
-22V
17 8
16 31 30 7
FIP DRIVER IC
IC601
BU2977FS
1
10
23 24 26
28
Q601
CG_DATA
RESET
CG_CLK
MICON
FL_CS
FRONT AUDIO IN R
J603
2
FRONT _A_IN_R
1
3
FRONT _A_IN_L
FRONT AUDIO IN L
J602
FRONT _V_IN
1
2
FRONT VIDEO IN
J601
1
TUNER/JACK/HI-FI/
21PIN/OSD
Y/C/AUDIO/CCD/
HEAD AMP
VCR EJECT
2
POWER
VCR/DVD
CH UP
CH DOWN
CP681
STOP
REC/OTR
FF/CUE
DVD LED
D681
PLAY
REW/REV
CP653
KEY-B
1
7
KEY-A
2
6
AT+5.2V
3
5
DVD LED
5
3
VCR LED
6
2
KEY-B
KEY-A
1
REM_IN
MICON
SEG 10
VCR_LED
SUB MICON/OSD/VPS
DVD_LED
VCR LED
D685
Q652
Q651
DVD/VCR
OS601
DVD/HDD LED SW
FIP ON SW
AT+5.2V
OPEN/CLOSE
F-17
F-18
TUNER/JACK/Hi-Fi/21PIN/OSD BLOCK DIAGRAM
(SD-22VB)
NICAM IC
IC801 TDA9874AH
SWD_VIDEO
Y/C/AUDIO/
HEAD AMP
EE/VV_V_OUT
25
15
29
14
30
2
38
1
2FSC
J8005
TU301
Q4501
5
3
11
12
22
21
2
22
24
BUFFER
8
DVD_B
7
DVD_G
11
15
DVD_R
DVD IN/OUT
7
DVD_V_OUT
10
J8003
Y_OUT
3
C_OUT
4
IC8003
BA3308F
W/ACL DUAL
PRE-AMP
40
9
Q8006
5
23
Q8003, Q8004
DVD RGB
H OUT
Q8005
OSD/VPS/PDC IC
IC4501
LC74775M-9839
2
21
19
10
6
9
1
2
DVD_A_OUT_R
DVD_A_OUT_L
7
19
SPDIF-134
13
30
42
31
41
44
CG_DATA
36
25
43
CG_CS
5
28
IIC_DATA
1
33
21
34
Q8001, Q8002
D AUDIO
DRIVER
F-19
3
23
CG_CLK
IIC_CLK
OPERATION/
DISPLAY
27
19
MIXER
AV SWITCHES IC
IC8001 LA73026V
Y/C/AUDIO/
HEAD AMP
41
20
11
MICON
16
24
MIXER
DVD IN/OUT
X801
24.576MHz
2
J8001
COAXIAL
37
22
26
2
20
HI-FI/AUDIO/CANAL SW IC
IC701 TDA9605H
HF1
35
42
HF_COM
36
43
HF2
37
6
NORMAL_A_IN
21
3
NORMAL_A_OUT
TU_V_OUT
22
7
17
2
18
15
FRONT_A_IN_L
10
16
FRONT_A_IN_R
11
3
2
J8002
AUDIO OUT
F-20
TUNER/JACK/Hi-Fi/21PIN/OSD BLOCK DIAGRAM
(SD-22VE)
Y/C/AUDIO/
HEAD AMP
NICAM IC
IC801 TDA9874AH
SWD_VIDEO
25
15
29
14
EE/VV_V_OUT
30
2
38
1
2FSC
J8005
TU301
Q4501
5
3
11
12
22
21
22
24
BUFFER
8
7
DVD_B
DVD IN/OUT
DVD_G
11
DVD_R
15
DVD_V_OUT
16
J8003
Y_OUT
3
C_OUT
4
TU/REAR VIDEO IN SW IC
IC8002 NJM2533V
OSD/VPS/PDC IC
IC4501
LC74775M-9839
40
2
21
23
2
7
Q8003, Q8004
DVD RGB
H OUT
19
AV SWITCHES IC
IC8001 LA73026V
11
10
1
35
2
19
SPDIF-134
13
30
42
41
44
OPERATION/
DISPLAY
F-21
36
25
CG_CS
5
28
IIC_DATA
1
33
IIC_CLK
21
34
22
26
2
20
HF1
Y/C/AUDIO/
HEAD AMP
31
43
J8001
COAXIAL
3
23
CG_CLK
2
19
18
7
Q8001, Q8002
D AUDIO
DRIVER
27
6
DVD_A_OUT_L
CG_DATA
41
20
9
DVD_A_OUT_R
MICON
24
1
3
DVD IN/OUT
X801
24.576MHz
37
HI-FI/AUDIO/CANAL SW IC
IC701 TDA9605H
35
42
HF_COM
36
43
HF2
37
6
NORMAL_A_IN
21
3
NORMAL_A_OUT
TU_V_OUT
22
17
7
18
15
FRONT_A_IN_L
10
16
FRONT_A_IN_R
11
2
3
2
J8002
AUDIO OUT
F-22
TUNER/JACK/Hi-Fi/21PIN/OSD BLOCK DIAGRAM
(SD-22VL)
NICAM IC
IC801 TDA9874AH
SWD_VIDEO
Y/C/AUDIO/
HEAD AMP
EE/VV_V_OUT
25
15
29
14
30
2
38
1
2FSC
J8005
TU301
Q4501
5
3
11
12
22
21
22
24
2
BUFFER
8
7
DVD_B
DVD IN/OUT
DVD_G
11
DVD_R
15
7
DVD_V_OUT
10
J8003
Y_OUT
3
C_OUT
4
IC8003
BA3308F
W/ALC
PRE-AMP
9
Q8006
40
5
23
Q8003, Q8004
DVD RGB
H OUT
Q8005
OSD/VPS/PDC IC
IC4501
LC74775M-9839
2
21
19
MIXER
10
DVD_A_OUT_R
19
SPDIF-134
13
30
42
31
36
44
25
CG_CLK
43
CG_CS
5
28
IIC_DATA
1
33
IIC_CLK
21
34
22
26
37
20
35
2
J8001
COAXIAL
3
23
2
18
HI-FI/AUDIO/CANAL SW IC
IC701 TDA9605H
HF1
35
42
HF_COM
36
43
HF2
37
6
NORMAL_A_IN
21
3
NORMAL_A_OUT
TU_V_OUT
22
17
7
18
15
FRONT_A_IN_L
10
16
FRONT_A_IN_R
11
2
3
2
1
F-23
1
7
CG_DATA
OPERATION/
DISPLAY
19
2
DVD_A_OUT_L
41
Y/C/AUDIO/
HEAD AMP
27
6
9
AV SWITCHES IC
IC8001 LA73026V
Q8001, Q8002
D AUDIO
DRIVER
41
20
11
MICON
16
24
MIXER
DVD IN/OUT
X801
24.576MHz
3
7
2
TU/REAR VIDEO IN SW
IC8002 NJM2533V
2
J8002
AUDIO OUT
F-24
DVD IN/OUT BLOCK DIAGRAM
(SD-22VB, SD-22VE)
CP8001
FROM/TO
DVD BLOCK
1
TX
TX
2
RX
RX
3
GND
4
GND
SUB MICON/
OSD/VPS
DVD RESET
MICON
DVD_MUTE
5
PCON+9V
6
PCON+9V
P.CON +9V
7
PCON+D5V
AT+5.2V
8
PCON+D5V
P.CON +5V DH
9
GND
10
PCON+3.3V
P.CON+3.3V
11
PCON+3.3V
P.CON+12V
12
GND
13
SPDIF-134
REGULATOR
SPDIF-134
Y_OUT
C_OUT
DVD_V_OUT
CP8002
FROM/TO
DVD BLOCK
1
Y(G)
DVD_B
2
GND
DVD_R
3
C(CVBS)
DVD_G
4
GND
DVD_A_OUT-L
5
CVBS
DVD_A_OUT-R
6
GND
7
DVD B
8
GND
9
DVD R
10
GND
11
DVD G
12
GND
13
AUDIO-L
14
GND
15
AUDIO-R
16
ZERO
17
DVD RESET
Q8015
MUTE SW
Q8014
MUTE SW
TUNER/JACK/HI-FI/
21PIN/OSD
Q8012, Q8013
MUTE SW
AMP
IC8004 NJM4580M
3
1
5
7
8
18
F-25
F-26
DVD IN/OUT BLOCK DIAGRAM
(SD-22VL)
CP8001
FROM/TO
DVD BLOCK
1
TX
TX
2
RX
RX
3
GND
DVD RESET
4
GND
SUB MICON/
OSD/VPS
MICON
DVD_MUTE
5
PCON+9V
6
PCON+9V
P.CON +9V
7
PCON+D5V
AT+5.2V
8
PCON+D5V
P.CON +5V DH
9
GND
10
PCON+3.3V
P.CON+3.3V
11
PCON+3.3V
P.CON+12V
12
GND
13
SPDIF-134
REGULATOR
SPDIF-134
Y_OUT
C_OUT
DVD_V_OUT
CP8002
FROM/TO
DVD BLOCK
F-27
1
Y(G)
DVD_B
2
GND
DVD_R
3
C(CVBS)
DVD_G
4
GND
DVD_A_OUT-L
5
CVBS
DVD_A_OUT-R
6
GND
7
DVD B
8
GND
9
DVD R
10
GND
11
DVD G
12
GND
13
AUDIO-L
14
GND
15
AUDIO-R
16
ZERO
17
DVD RESET
Q8015
MUTE SW
Q8014
MUTE SW
TUNER/JACK/HI-FI/
21PIN/OSD
Q8012, Q8013
MUTE SW
AMP
IC8004 NJM4580M
3
1
5
7
8
F-28
POWER BLOCK DIAGRAM
(SD-22VB, SD-22VE)
CP502
T501
16
HEATER_DC-
15
-22V
14
20
TUNER 32V
13
11
P.FAIL
12
12
13
14
7
2
HEATER_DC+
18
6
GND
11
GND
10
POWER ON H
9
UNREG 3.3V
8
UNREG 3.3V
7
AT 5.2V
6
AT 5.2V
5
AT +13V
4
MOTOR GND
3
MOTOR +12V
2
REGULATOR
1
NC
4
15
9V REG
IC502
KIA7809API
D505, D506
D502, D503
IC501
KIA431
Q501
SW.
Q502
PROTECT
CONTROL
IC503
LTV-817M-VB
PHOTO
COUPLER
VOLTAGE
CTL. IC
3
1
1
2
3
Q504
P.CON+B
SW.
Q505
P.CON5V
SW.
Q506
P.CON SW.
L501
AC IN
CP503
F-29
P.CON+5V D
1
GND
2
P.CON+5V A
3
GND
4
P.CON+9V A
5
MOTOR GND
6
DVD DRIVE
F-30
POWER BLOCK DIAGRAM
(SD-22VL)
CP502
T501
16
HEATER_DC-
15
-22V
14
20
TUNER 32V
13
11
P.FAIL
12
12
13
14
7
GND
11
GND
10
POWER ON H
9
UNREG 3.3V
8
UNREG 3.3V
7
AT 5.2V
6
AT 5.2V
5
AT +13V
4
MOTOR GND
3
18
MOTOR +12V
2
19
MOTOR + 24V
1
2
6
HEATER_DC+
REGULATOR
4
15
9V REG
IC502
KIA7809API
D505, D506
D502, D503
IC501
KIA431
Q502
Q501
SW.
PROTECT
CONTROL
IC503
LTV-817M-VB
PHOTO
COUPLER
VOLTAGE
CTL. IC
3
1
1
2
3
Q504
P.CON+B
SW.
Q505
P.CON5V
SW.
Q506
P.CON SW.
L501
AC IN
CP503
F-31
P.CON+5V D
1
GND
2
P.CON+5V A
3
GND
4
P.CON+9V A
5
MOTOR GND
6
DVD DRIVE
F-32
SUB MICON/OSD/VPS BLOCK DIAGRAM
(SD-22VB)
TX
DVD IN/OUT
RX
MICON
SUB_CS
32
OPERATION/
DISPLAY
MICON
DVD_LED
1
VCR_LED
2
SUB_CLK
6
SUB_DATA_IN
7
SUB_DATA_OUT
8
9
31
SUB MICON
IC3005 OEC7080A
30
11
12
16
SUB_RESET
X3003
4 MHz
F-33
F-34
SUB MICON/OSD/VPS BLOCK DIAGRAM
(SD-22VE, SD-22VL)
TX
DVD IN/OUT
RX
31
OPERATION/
DISPLAY
DVD_LED
1
VCR_LED
2
SUB_CLK
6
SUB_DATA_IN
7
SUB_DATA_OUT
8
SUB MICON
IC3005 OEC7080A
30
MICON
SUB_CS
32
9
11
12
16
SUB_RESET
X3003
4 MHz
F-35
F-36
PRINTED CIRCUIT BOARDS
DVD (BOTTOM SIDE)
DVD (TOP SIDE)
D8502
D8505 D8504D8503
D8501
R8541
R8523
R8522
R8542
R8540
C1019
B8503
C8518
C8528
R2028
R2030
R2033
R2035
C2030
R2037
R2039
R8504
R4004
Q8502
Q8501
R4003
R4010
IC4002
C2046
C2051
81
121
W203
IC4001
C4012
R2611 D2601
C2635
R2018
C2611
C2612
C4010
IC1005
C1018
C4048 R4034
W104
R1099
NR1001
R1060
C1011
37
73
IC1002
IC1001
R1027 C1003
R1026
1
109
W102
R1002
R1003
R1012
R1016
R1014
R1037
R1025
C2604
IC4006
C1007
R1095
IC2601
CP2603
IC2602
R1047
C4044
R2632
C2626
W262
C2605
X1001
C1012
R1024
Q2602
R2638
R2639
17
1
W103
R1033
R2637
R2607
R1058
NR1003
IC2603
NR1009
NR1005
NR1010
NR1011
NR1007 NR1008
R2635
R4029
33
49
NR1006
IC1006 NR1004
W261
R4020
C2640
NR1002
Q2001
R4030
R4031
R4016
R4017
R4018
R4019
R2608
R2046
C2038
R2047
R4028
R4027
R4026
R4025
R4024
R4023
R4022
R4021
R2031
R2002
R2044
C2029
C2041
45
C2039
C2037
R2045
R2617
C2606
41
1
1
R2049
R2015
C2028
C2633
R2614
C2601
C2603
Q2603
Q2604
R2619
C2624
Q2605
R1049
R1050
R2623
W406
R2603
W403
C2614
R2642
C4045
R2627
R1036
R1031
R1040
R1030
R1041
R1021
L4001
C4033
R4005
CP2601
C2615
R2625
R1044
R1042
R2633 C2628
R1005
R2636
R2610
Q2601
R8507
IC2001
C2610
R2601
C2619
R1022
R1017
IC4005
R1034
R1035
R2628
R2626
R2634
C2639
C2613
C2620
C2638
R1011
W101
R1001
G-1
C2625
C1013
R1029
R1028
R1015
R1013
R1018
C2020
C2015
C2014
R2616
C2010
R2010
C2609
R2008
R2612
R2622
C2616
R2621
R2615
C2623 C2607
R2629
C2630
C2632
C2631
C2634
C2629
C2622
C2621
C2617
R2048
R1009
R1006 R1010
R4007
Q1003Q1004
R2023
R2624
C2618
R2630
R1038 R1039
R2014
R2022
R2618
C2608
C2026
R2019
C4006
C4005
C2035
R2013
R2613
R2042
D2602
R2006
R2050
W851
R8501
R2024
R2609
R2641
R2012
C2602
W205 W204
C2006
R8503
R8502
Q4001
B8502
89
R8505
R4015
C4003
133
C2024
C2060
CP2602
C2050
C2048
C2047
C2001
R2026
C2005
IC2002
IC4003
C2025
R2020
R2005
W207
W206
C2049
R2052
C4037
R2036
C2019 C2018
R2016 C2027
C2004
C2011
C2023
R2009
W208
C2007
R2001
R2004
C2021
C2002
R2011
C2008
C2003
R2021
C2040
R4001
W202
W201
C2036
R4002
R4006
C4020
C2042
C4008
R2631
R2038
C2031
C2045
IC4004
R2027
R2029
R2032
R2034
C4031
D4001
C4041
R4013
R4012
R4009
C2044
C4038
R8509
R4011
W867
C1027
Q8505
R8506
C1009
C1010
C8503
W866
W869
C4007
C8506
R8518
R8519
C1025
Q8503
C8526
C4029
C4004
R8544
C8525
B8501
X8501
R8545
C1029
C1028
R8511
C8501
R8513
R8548
C8510
R8546 R8508
Q8507
C8523
R8515
R8512
C8509 W858
C8502
C8514
R8517
IC8503
C8529
C1021
C8508
W857
C1020
C1022
C8524
R8521
C8504
R8520
R8516
R8529
R8530
C1030
R8526
C8517
R8525 C8519
W855
C8507
R8532
C8521
C8505
IC8501
C8516
C8520
Q8513
R8531
W861
C8513
C8539
Q8511
R8527
C8542 R8514
C8522
L8501
C8515
Q8510 Q8512
C8543
R8510
W856
CP8502
C8512
R8524
Q8508 Q8509
IC8504
C8511
R8528
C8537
CD8502
CD8501
W854
G-2
PRINTED CIRCUIT BOARDS
VCR (INSERTED PARTS)
SOLDER SIDE
C8096
C8099
C1703
C8084
C8087
R1709
C1712
D1708
R1712
D1709
W015
C1707
R8076
R8077
W057
W132
W133
W136
W139
W140
W138
W137
R3024
W135
W213
W258
W260
W261
W264
W265
W266
C3033
C3019
W011
C8020
W006
W008
W820
C191
W007
W009
C3030
C3020
C106
C3032
W074
W073
W070
W200
W199
W203
C8030
CP102
C8043
W151
W149
C8038
C8045
C8041
C8053
C128
C126
L112
C167
C4503
C4507
C4516
C4515
W043
C8059
W861
C8048
C8051
C8033
L8004
C8028
C8021
C8025
C117
C137
L109
C142
C147
W145
W148
W272
L4505
W018
C203
W146
L113
W221
W147
L116
W225
W218
R145
L124
W226
W224
C193
C184
C179
L8007
L8006
W093
C8008
R112
C161
C153
C174
W154
W286
W284
W285
W281
W253
W282
W283
W229
W886
W152
W194
W198
W201
C115
C113
C187
C8040
W069
W068
C8014
W005
W204
W195
W196
W206
W208
W209
W202
W197
L8005
W309
W193
J8002
D8005
L8001
C1713
C1710
C1711
C8115
L8003
W016
R1708
C1714
Q1702
W890
C1708
W818
W063
W061
W062
B8005
W059
W110
W111
C3002
W180
W179
W177
W109
D8010
W065
W117
C8085
W119
W807
W185
C3028
W064
W307
R8049
C8097
C8098
C8091
C8101
C8088
W121
W122
W191
W186
W187
W190
Q1703
R3020
5
00
Q3
OS8001
W079
C3022
W809
W808
W098
CP101
C8032
W037
W230
W232
W231
C651
W292
C8017
C809
W868
C143
W844
L8017
D8007
C716
C719
C722
C729
C727
C730
C726
C724
C708
C821
C801
W826
C802
W287
W288
W873
W843
W158
C718
R708
C720
W033
C703
C715
C714
W096
C713
C711
C8016
C155
C130
X101
C154
W308
C163
W296
C4511
W049
W171
C302
C301
C308
C304
C8083
C8075
W104
R8074
W172
W173
W167
W170
W241
W831
W830
C812
W166
L8016
C8060
C8069
C8065
L8011
D8006
C731
C728
C725
C721
C717
L802
C810
W240
W865
R303
W045
W099
W237
W102
W101
W168
W169
W238
TP102
W239
TP701
TP101
W836
W835
W834
W832
W046
W047
W100
TU301
R1721
W298
G-4
G-3
X801
W053
J8005
W030
W813
W048
Q8005
Q3002
W299
W032
W095
W883
W050
W840
W301
CP1
03
W300
W051
W839
W801
W838
R8031
W829
W034
CP651
W845
W054
W846
W028
C8118
W108
W242
W052
W174
W837
W303
W161
W029
W828
SW3001
L8015
W036
W160
W289
C825
W035
L702
Q3006
W827
L701
W291
W164
R4514
W162
W290
W039
W038
R3018
W856
W040
W293
W020
W862
W234
W235
W019
W863
W041
R4513
L8002
W165
L4503
L107
W044
W236
W297
W860
W881
W216
W269
L108
W219
L105
W268
J8003
L106
L4507
W852
W215
R8004
W222
S805X
W882
W270
W271
W220
W273
W091
D3001
W089
R3004
W022
W311
L103
W023
W869
R127
S805Y
W072
W025
W276
W277
W227
W275
W274
W092
W310
L111
J8001
L110
D8004
Q106
W153
W885
L104
C3015
W278
Q107
W280
TP3001
W125
B8001
W124
W254
Q102
W305
W205
D8001
D101
W126
W210
W076
Q104
W211
W257
W012
W010
W077
W078
W887
W212
W851
W192
W251
W247
W267
R3031
W810
W255
D8009
W259
Q3007
W013
R1711
W080
W131
W130
TP3002
W014
R1706
W867
D1710
Q1706
W082
W081
W866
W134
W263
W017
R1720
W083
W143
R3045
W085
R1713
W084
W144
W214
W150
W279
IC3099
X3002
W243
W141
W262
R3005
C8004
Q1713
R1717
Q1712
W086
W803
W056
R3017
R3044
W822
R3040
W244
Q1701
D1711
R8063
Q1708
CP
W175
W176
W112
W178
W058
R3006
X3001
1
0
30
Q3004
S804Y
C3038
D3002
R1722
W116
W184
W113
W181
R1703
D1702
W115
W183
W002
W001
W066
X3003
W114
W182
W003
D1703
W004
W118
W850
W067
W120
CP1701_1
S804X
CP8001
CP8002
Q3001
CP653
(SD-22VB)
PRINTED CIRCUIT BOARDS
VCR (CHIP MOUNTED PARTS)
SOLDER SIDE
C310_1
R304
C303
(SD-22VB)
C307
C8072
R8020
W902
R814
R717
R716
12
R714
C815 C808
C824
C701
Q652
51
C4501_1
R4502
IC102
R146 C201_1
C204
IC4501_1
R110
C8012
R3022
R3015
R702
C188
C3034
R3039
C3027
C3023
R3026 R3025
R3049
R3047
R3048
R3050
17
R8067
R3001
C8090
R8052
R8050
R8060
R8051
R8054
R8048
C3025 R3037 C3026
C3039
R8055
R8053
R8062 C8089
R8047
R8059
C8095
C8092
C8094
1
9
R8061
R8056
C8093
R8058
R8057 C8100
05
30
IC
IC8004
C8117
R3052
25
C3036
R3016
R3014
R3036
R3046
Q1714
R3030
R3012
51
81
R3032
C3016 C3010
IC3004
IC
30
01
C3011
C3009 R3009
Q8012
R3051
C3040
Q1709 Q1711
C3007 R3011
R3008 C3008
R3010
R8082
31
R3007
R3013
C8002
R1715
R3033
R1714
R3029
R3054
1
R3034
R3035
C3018
C3037
R3043
Q8013
Q3009
R3028
C3035
C3024
W894
W893
R3038
R3041
R666
R667
R101
R105
R1707
R1716
Q3008
Q105
C3029
C3021 C3031
C111
R106
C109
C108
Q1707 Q1705
G-5
R4508
C183
W857
C168
C171
C166
C181
C172
R3021
Q8015
Q8014
C8003
C175
C4517_1
R4511
Q110
R8006
C8018 R8002
C8010
R8005
C8006
C190
Q113 Q108
Q8002
R8007
L4502
C4506
C4508
R3019
C164 R126
R111
C4504
Q3003
C116
R109
R8003
R4503
R122
C150
C192
C8013
C8015
C194
R115
C140
R117
R132 C157
R123
C162 C156
C8036
R8010
C8027
C8029
C8049
C8047
C8031
C8026
C8005
C189
31
R8001
C8035
R8009
Q8001
L4501
C8009
R8070
C8019
R8015
R8013
IC8001
R4510
R4512
C4512
C177
C8023
R107
Q4501
W892
1
R113
Q111
R144
C170
C186
C205_1
R148
R134
R135
C158
C159
R125
C135
C127
R114
81
1
10
IC
C144
C131
C107
C136
C804
C118
C120
C165
R706
C148
C169
C173
R8023
C129
C8011
R8017
C837
C139
C125
C134
C122 C121
R8032
34
C149
R8041
R8030
C822
C119
R8034
C709
C710
C123
C132
C124
C133
R121
R119
C145
C712
C8102
1
R116
R707
23
C141
C146
C152
R118
34
C151
R120
R8036
R8045
R8043
R8035
1
R705
C705 C702
23
W901
C8007
C8081 C8073
C8078 C8067
C8082
C8062
C8079
R8040
12
1
70
IC
C8068
C723
R709
R711
C8116
Q8003
R8021
1
80
IC
R8068
Q8004
C4514
R4509
R701
R8018
C816
C835
C807
R710
R715
W903
C4505
R4505
R8026
C8039 R8075
R8037
R8019
R718
R719
R720
R721
R713 R712
Q8006
R8024
R8029
R8022
R8042
R8025
C8057
IC8003
R8033
R8028
R8046
R8027
C305
C8080
R3003
R8044
R302
C306
R305
Q651
G-6
PRINTED CIRCUIT BOARDS
VCR (INSERTED PARTS)
SOLDER SIDE
(SD-22VE)
C8096
C8098
C8099
R1709
C8004
C1707
L8001
L8003
C1713
R8076
R8077
C8020
W011
W006
W008
W820
W007
W009
C191_1
C8014
C8040
W068
W074
W073
W069
W070
C8030
CP102
R112
C153
D8005
J8002
C8043
W093
C8045
C8053
C8051
W018
C8059
W043
C126
C8048
C8033
C128
C8025
L8004
C8041
J8003
W044
L8002
L8006
L8007
C8038
C8021
C8028
C117
C137
C147
W147
C142
C8008
W023
W020
W019
CP101
W098
W042
W041
W861
W862
W863
W040
C8050
L702
W039
W038
C8032
L701
C8017
W096
C715
C714
C713
C711
C8016
C155
W097
W037
W036
L8015
W035
W034
J8005
R708
C720
W158
C718
W033
W032
W095
W030
W029
W028
C8118
W054
L8008
D8007
W171
W170
S806Y
W049
W815
W100
W047
C302
W048
W046
W865
W864
W045
W099
W102
W101
W172
W237
W173
W167
W166
W168
W169
C308
W104
W883
Q112
W816
L8011
W053
W052
D8006
C728
C725
C721
C717
C731
W106
D8013
L8017
C8022
C8024
C726
C708
C724
C730
C727
C729
C722
C719
C716
W108
S807X
03
CP1
R1708
C1714
C1712
D1709
C1710
C1711
C8115
W057
C115
B8001
R8004
TU301
G-7
D1708
R1712
W063
W823
W061
W062
W059
C113
C161
L105
W105
L101
W238
TP102
W239
TP701
TP101
W835
W836
W834
W832
Q3002
W890
W818
C1702
B8005
C8085
C106
W089
J8001
D8004
W022
W091
W840
X801
W005
W025
W860
C130
C703
C143
C4615
C105
W241
Q101
W174
D8001
W878
W846
C101_1
C1708
C8084
C8087
W132
W133
W139
W140
X101
C154
W845
OS8001
W012
W026
L109
L112
R4617
L4603
W013
W027
W802
L4605
W838
W301
C187
C174
W145
W148
W308
C163
C4622
C4625
L102
C4605
D4601
L802
W831
W830
C812
W839
W869
L107
W157
W015
W010
L8005
L108
W161
W159
W871
R1711
L106
W160
W870
C821
C801
W826
C802
C810
W837
W150
W162
C825
W242
Q107
R131
W827
L103
Q106
W153
W151
W149
L116
W164
L4604
R4603
W828
W072
W165
L4602
C4609
W844
W287
W288
CP651
W873
W843
Q3006
R4623
C809
W868
W290
L4601
C4626
C4601
W292
C651
W230
W232
C4511
R3018
L104
L111
C184
W146
W852
W233
W293
W154
W152
W886
W882
W016
D1710
Q1706
W014
TP3001
R127
C167
W234
L4503
W300
Q102
W881
S807Y
W236
W235
W082
W081
Q1713
W017
R1720
R1706
Q104
L110
W885
Q1702
R1721
R1713
R1703
Q1703
Q1712
W080
W311
W221
L113
S806X
C203
W296
C4503
C4507
C4516
W216
W215
W224
W270
C193
C179
R145
W218
W272
L4505
C4515
W225
W226
R3004
W220
W219
W829
D101
W200
W199
W198
W222
W273
W201
W194
W207
W203
W204
W195
W196
W206
W208
W209
W202
W197
W309
W193
W229
W228
W281
W274
L4507
W136
C3030
C3020
W809
W808
W275
W227
W085
W076
W124
D3001
R1717
W803
W867
C1703
C8097
Q1708
D1712
W002
W003
W079
W078
W125
W305
W205
Q1701
W817
W077
W128
W127
W126
W210
W253
W282
W283
W284
W285
W310
W084
D1703
D1702
W086
W887
W211
W276
SW3001
W138
C3033
C3019
C3032
W286
W278
R4514
W135
W258
W212
W810
W279
L4504
W137
W213
W260
W261
W265
W264
W266
C3015
W280
W299
W004
D1711
W056
W866
W130
Q3007
W255
W134
W083
W875
W131
W257
W303
W141
D8009
TP3002
W254
W144
W143
C3022
R3031
CP3001
W214
X3002
R3024
W267
W262
W289
W065
W117
W110
R3040
R3017
05
W259
W856
W291
R8049
R3006
0
Q3
R3045
W297
W066
W064
W112
CP1701_1
W850
W067
R8063
D8010
C3038
W175
R3005
W269
W268
R1701
W058
R3044
W271
W115
W111
W109
W179
W180
W177
R3020
W176
W243
W277
W851
W113
X3001
IC3099
CP8001
W114
D3002
W178
W244
W263
W116
C3002
W181
Q3004
W118
W307
W807
W247
W183
W182
W120
C3028
W119
W185
S804Y
C8088
X3003
W184
W121
W122
W191
W186
W187
W190
W251
Q3001
C8091
C8101
W192
S804X
CP8002
R1
70
2
CP653
G-8
PRINTED CIRCUIT BOARDS
VCR (CHIP MOUNTED PARTS)
SOLDER SIDE
C310_1
(SD-22VE)
C306
R3003
C8072
C305
S808Y
C103
W902
R814
R114
C204
R3015
C181
C168
C171
C166
S808X
C3034
17
C3027
C3023
W892
R3036
R3034
R3035
C3018
R3012
R3054
R3026 R3025
R3049
R3047
R3048
R8067
R3001
C8090
R8050
R8052
R8062
R8060
R3055
R8047
C3025 R3037 C3026
C3039
R8055
R8053
C8089
R8059
C8095
C8092
C8094
R8056
C8093
R8058
R8057 C8100
05
30
IC
9
C3036
R3016
R3014
R3050
25
1
R3030
R3032
R3046
Q1714
R3052
81
51
R3051
C3040
IC3004
R3007
R3013
C3016 C3010
C3007 R3011
R3008 C3008
R3010
C3009 R3009
Q8012
IC
30
01
C3011
R3033
31
R3029
R3039
1
R8082
R8048
Q3009
R3028
C3035
C3024
R3021
R101
R105
W894
W893
R3038
R3041
Q3008
Q105
C3029
C3021 C3031
R667
C116
R109
R138
R1707
R1715
C4514
R4509
R702
Q8013
R8051
R8054
S805Y
Q109
C188
C3037
R3043
R8061
C4517_1
R4511
W857
R666
C164 R126
C114
L4502
C4506
C4508
R4508
C183
C194
R115
R4503 C4504
Q3003
R1714
C8002
R4510
R4512
C4512
S805X
Q1707 Q1705
G-9
Q4501
C4510
C201_1
R4507
R4625
R4624
C4501_1
R4502
R146
Q652
C4505
R4505
Q4605
C175
C172
Q113 Q108 Q110
C111
R106
C109
C108
IC8004
C804
R3019
C190
C8012
C8117
C807
C824
R4607
R4604
C4617
C4614
C4612
IC102 Q111
R122
Q8015
R1716
C837
C177
C150
R110
Q1709 Q1711
34
IC4501_1
51
31
R111
R8006
C822
C4602
R4605
C4607
R4606
C4606
R4602
C4613
R4612
C4611 R4621 C4619
R4610 R4616 C178
C4604
R130
R4618
R4601
C169
C173
C165
C158
C159
R125
Q4602
R134
R135
C149
C119
1
1
C4603
C4621
C4623
R4626
C138
C4624
R116
R4615
C170
C136
C4608
R4619
C701
C141
C146
C152
R118
C4620
C186
R113
Q8014
C8003
R705
C705 C702
C712
81
Q8002
R8007
C118
Q4606
Q4601
IC4601
23
L4501
R8072
C8036
C8027
C8029
C8049
C8047
R8003
C8013
C8015
C112
C140
W896
C8009
R8070
C8019
R8015
Q8001
R117
R8001 R8073
R8010
C8018 R8002
C8010
R8005
C8006
IC8001
C8035
R8009
C8031
C8026
R8013
R107
R4622
C148
1
10
IC
C8023
C131
C135
C127
C129
C8011
C144
C120
R4620
C4616
C139
C125
C134
C122 C121
C107
Q4603
C709
C710
C123
C132
C124
C133
R121
R119
C145
W895
C8007
R8011
R8071
R8023
R706
R707
R8041
R8030
C8005
1
34
C8102
R8034
R8017
23
C151
R120
R8036
R8045
R8043
R8035
R8032
R711
W901
C8046
IC8002
R8066
12
R132 C157
R123
C162 C156
R8068
C8116
R8040
C8081 C8073 R8039
C8078 C8067
C8082
C8068
C723
R709
1
70
IC
C8079 C8062
R8021
R4609
C815 C808
1
80
IC
R4614
12
R144
R716 R714
Q8004
Q8003
C835
Q4604
R4611
R701
C8109
Q103
R102 C102
C205_1
R148
R717
R103
C4610
R4608
R104
C104
R8029
R710
R8028
R715
R8027
R8022
W903
16
C8057
C8
R718
R719
R720
R721
R713 R712
Q651
G-10
PRINTED CIRCUIT BOARDS
VCR (INSERTED PARTS)
SOLDER SIDE
(SD-22VL)
CP8002
C8096
C8098
C8099
R1709
Q1702
D1708
R1712
W063
W823
W061
R1708
C1714
C1712
W890
C1708
W818
C1702
D1709
L8001
C1713
C1710
C1707
C8020
W008
W011
W006
W820
C8040
C8030
D8005
J8002
C8043
L8007
C8038
C8045
W020
C8059
C8048
W018
C8053
C8051
C8033
L8004
L105
C126
C128
C8025
C8028
C8021
J8003
W861
W043
C155
W098
W042
L8002
L8006
C8008
W022
R8004
C8041
W044
W041
W862
W863
W040
W097
C8016
C8032
W039
W038
W037
C8017
C8050
W096
L8015
W036
W035
W034
C720
W033
W032
W095
J8005
D8013
W029
D8007
W108
C8022
C8024
C726
C730
C724
L8017
C708
W878
W030
W028
C8118
W106
W054
W053
C8065
W051
Q8005
W047
C304
C301
C302
W046
W865
R303
TU301
W048
W049
L301
W045
W099
W102
W101
W237
W100
W050
C308
C8083
C8075
W104
R8074
C8060
C8069
W172
W173
W166
W167
L8016
W171
L8008
W052
R8031
L8011
D8006
C731
C728
C725
C721
C717
03
W007
W009
C8014
W074
W068
W073
W069
C117
L109
R708
C727
C729
C722
C716
W168
W169
CP1
B8001
D8004
W019
L702
C718
W158
W170
W238
W239
TP101
TP102
TP701
W836
W835
W834
W832
X801
W070
C191
C137
L106
W105
L101
W840
Q3002
R8076
R8077
CP102
W093
C714
C715
C703
C143
C105
W241
L102
L802
W831
W830
C812
C810
W174
W005
W025
L701
C713
W161
D8001
W023
W089
CP101
C130
C154
X101
C163
W308
C821
C801
W826
C802
W301
W062
B8005
C8115
W057
R112
W802
W091
W860
L112
W146
C167
W868
C809
W844
W843
W287
W288
W873
CP651
C101
Q101
D1702
C8084
C8085
W059
C113
C153
C147
W147
W148
W145
W221
L107
C719
W839
R1
70
2
C8097
C161
L116
C142
W852
C825
W838
OS8001
W010
W077
L8005
L108
W846
G-11
W132
C106
C174
W151
W149
C184
W224
W226
L113
W225
W882
W828
W300
C8091
W065
W117
W110
W133
W139
W154
W152
W886
C193
C179
W311
W242
W299
C115
W869
R127
W160
W837
W013
J8001
Q107
W150
W162
W829
L8003
W015
W012
Q106
L111
W845
W303
R8049
D8010
W153
W885
W827
SW3001
W136
C187
C711
Q3006
D1710
W072
W165
W164
W016
Q1706
L104
W124
W201
W194
W198
W230
W292
C651
R3018
W290
W289
W234
W232
W293
R4514
L110
W200
W199
W203
W235
R1720
W014
Q102
W881
W236
C4503
C4511
W296
R4513
L124
W215
C8004
W017
R1713
R1711
TP3001
L103
C203
W216
L4503
W856
W291
W218
W270
C4507
W297
W272
C4515
W268
R3004
W219
C4516
W269
W220
R145
L4505
W271
W204
W195
W196
W206
W208
W209
W202
W197
W309
L4507
W273
W193
W228
W809
W808
W227
R1706
Q1713
R1721
Q1712
W080
Q104
W305
W274
W082
W081
Q1703
W076
D101
D3001
W085
W803
W867
W126
W205
W222
W084
R1703
W079
W125
W229
W275
W140
C3020
W310
W276
W277
R1717
W086
W887
W211
W210
C3030
W278
Q1708
C1711
W056
W866
W137
C3033
C3019
W279
IC3099
D1712
W003
C1703
W817
W078
W810
W281
W253
W282
W283
W284
W285
W280
W138
W258
W130
W212
W286
W254
R3024
D8009
C3032
W255
W134
W083
W002
D1703
Q1701
R8063
W875
W135
W213
W260
W261
C3015
W257
W141
W131
Q3007
D1711
C8087
W144
W143
C3022
TP3002
W111
W109
W214
W264
R3031
W265
W266
W259
W004
W066
W058
5
W267
W263
3
CP1701_1
W851
W067
R3040
00
Q3
X3002
W262
W064
W179
W180
W177
R3020
CP
1
00
R1701
W850
W113
R3006
R3045
R3005
W115
C3038
W112
W175
X3001
R3017
R3044
C3002
D3002
W244
W243
W116
W178
W176
W307
W247
W181
Q3004
W118
W114
W119
W807
W183
W120
C3028
W185
S804Y
C8088
Q3001
W184
W182
W121
W122
W186
X3003
W191
W187
W251
W190
CP653
C8101
W192
S804X
CP8001
G-12
PRINTED CIRCUIT BOARDS
VCR (CHIP MOUNTED PARTS)
SOLDER SIDE
C310_1
R304
C303
(SD-22VL)
C307
C8072
R8020
C103
R717
R701
R716 R714
R103
Q103
C835
W902
R814
R102 C102
12
C815 C808
C824
C701
R705
C705 C702
R116
C110
C3035
C3024
R3021
C3034
R3039
C3027
C3023
C3025
R3037
W892
R3012
R3036
C3026
R3026 R3025
R3049
R3047
R3048
R3055
R8067
R3001
C8090
R8052
R8050
R8060
R8051
R8054
R8048
R3016
R3014
C3039
R8055
R8053
R8062 C8089
R8047
R8059
C8095
C8092
C8094
R8056
C8093
R8058
R8057 C8100
17
9
C3036
R3050
05
30
IC
G-13
25
1
R3030
R3032
R3046
Q1714
R3052
81
51
R3051
C3040
IC3004
R3007
R3013
C3016 C3010
C3007 R3011
R3008 C3008
R3010
C3009 R3009
Q8012
IC
30
01
C3011
R3033
R1715
C8002
R8082
31
R3029
R3054
R1707
1
R1714
IC8004
Q3009
R3034
R3035
C3018
R101
R105
W894
W893
R3028
R667
Q3008
Q105
Q1707 Q1705
C8117
C4514
R4509
R702
C3037
R3043
R8061
W857
C188
C116
R109
C111
R106
C109
C108
Q1709 Q1711
C4505
R4505
R144
R3022
S805Y
C4517_1
R4511
R3038
R3041
Q113 Q108 Q110
R3015
C166
C181
C172
C3029
C3021 C3031
C8012
L4502
C4506
C4508
S805X
R666
R110
C175
C168
C171
C114
R111
Q8013
R4510
R4512
C4512
R4508
C183
R4503 C4504
Q3003
R3019
C190
Q8015
R1716
C4501_1
R4502
C169
C173
C165
R134
R135
C205_1
R148
C149
C158
C159
R125
C194
R115
C112
C140
C8009
C204
R122
Q8014
C8003
C201_1
C177
C150
Q8002
R8007
R146
IC4501_1
51
31
C164 R126
C8036
C8027
C8029
C8049
C8047
R8003
IC102 Q111
Q4501
L4501
C8013
C8015
R8006
C8006
R8070
C8019
R8015
Q8001
R117
R8001
R8010
C8018 R8002
C8010
R8005
C8005
IC8001
C8035
R8009
C8031
C8026
R8013
R107
C186
C136
1
C804
Q652
C170
1
10
IC
C8023
81
R113
R114
C144
C135
C127
C129
C8011
R8071
R8023
C131
C107
C148
C118
C134
C122 C121
34
C837
C125
C120
1
C139
C119
R8011
R8041
R8030
C822
C709
C710
C123
C132
C124
C133
R121
R119
C145
C712
C8102
R706
R707
R8034
R8017
1
34
C151
R120
R8036
R8045
R8043
R8035
R8032
23
23
C141
C146
C152
R118
R711
C8046
W901
C8007
R8040
C8081 C8073 R8039
C8078
C8067
C8082
C8068
R8066
12
C723
R709
IC8002
1
70
IC
C8079 C8062
R8021
R132 C157
R123
C162 C156
R8068
Q8003
1
80
IC
C8116
Q8004
C807
R104
C104
R8024
Q8006
C8109
R8018
W903
R715
R8044
R8026
R718
R719
R720
R721
R713 R712
R710
R8029
C8039 R8075
R8037
R8019
R8025
R8046
R8028
R8022
R8042
16
C8057
IC8003
C8
R8027
C305
C8080
R3003
R8033
R302
C306
R305
Q651
G-14
PRINTED CIRCUIT BOARDS
DISPLAY (INSERTED PARTS)
SOLDER SIDE
C616
B
V601
B
OS601
SW602
B
SW605
CP601
SW603
SW604
C604
W016
C613
W001
W002
W003
W006
R610
W008
W009
W010
R607
W011
R603
W015
W012
W013
AUDIO_R
R605
AUDIO_L
C615_1
VIDEO
J602
W004
W005
W007
W017
J603
J601
C614_1
R606
R611
R608
C607
D601
C608
C609
R604
R602
R601
Q601
SW601
DISPLAY (CHIP MOUNTED PARTS)
SOLDER SIDE
IC601
OPERATION1/OPERATION2
SOLDER SIDE
CP681
SW682
SW688
R690
SW681
R685
R694
R688
D681_1
R689
D685_1
R686
SW687
R681
R683
SW684
R687
SW686
SW689
S682X
S681X
S682Y
G-15
S681Y
G-16
PRINTED CIRCUIT BOARDS
POWER
POWER
SOLDER SIDE
SOLDER SIDE
(SD-22VE, SD-22VL)
(SD-22VB)
CP503
CP503
CP502
CP502
C527
C517
C510
W808
W002
W001
C505_1
C518
D512
L505
L503
C519_1
C501
C521
C501
W802
D522
D507
C507
D532
R519
R533
R518
C506
D521
IC501
D508
C516
IC503
C516
IC503
C524
R525
02
_1
25
_1
25
C5
5
F501
D502
FH501
D506
L501
D505
_1
02
S502_1
S501_1
2
D503
C5
+
CD501
D502
D506
FH502
D505
D503
1
2_
0
C5
F501
C 51
Q502
L501
D509_1
5
CP501
R51
C513_1
W805
R508
C 51
C508_1
2
HS501
R505
Q502
R51
C513_1
R505
D509_1
R508
R504
+
Q501
R506
R504
HS501
C511_1
B501
W007
Q501
R506
T501
R516
W004
D510
C509
R507
W011
C5
D524
R524
C528
B501
W004
C509
D510
W011
C528
W007
C511_1
T501
R5
D531
D531
R516
D524
R507
02
D530
R5
W805
D525
IC502_1
L507
R531_2
R517_2
L503
R522
R525
C508_1
D529
B503
W003
R520
D507
D530
R524
C514_2
R510
R536
C510
R521
R533
R519
IC501
C529
W804
C523
W008
D522
L506
C522
D529
W802
W003
W811
R509
D515
W009
W804
D521
C524
D523
W010
L505
C521
D532
R522
R518
R520
C523
C520
D526
B503
W008
R521
C518
D512
C522
W814
Q504
D518_1
C505_1
C519_1
R531_2
R517_2
D515
W009
Q505
R513
HS502
W005
L506
C529
C520
D523
W010
W808
W811
W001
W002
R509
D526
C527
C517
D525
D518_1
Q504
C530
Q506
W814
L507
R536
R510
W005
Q505
R513
HS502
IC502_1
C514_2
C530
Q506
FH502
FH501
RISK OF FIRE - REPLACE AS MARKED .
G-17
RISK OF FIRE - REPLACE AS MARKED.
G-18
B
C
D
R2601
E
F
G
H
READ CHANNEL SCHEMATIC DIAGRAM
4.7K
R2642
A
(DVD PCB)
10K
R2615
R2623
5.0
10
GNDS
LVL
5
3.6
6
0.2
1.7
7
8
1.3
1
1
DMFG
14
0
VRC
SCO
SCL
BCB
DPO2
DPO1
VCCP
15
0
32
31
30
29
28
27
26
25
24
0.0022 B
23
SCB
22
DMFG
21
20
PUDET2
LSRDVD
LVL
DMFG
LDMN
0.1 F
16
C2638
LDMP
RESET
TOPN
TCLS
LMT
PUDET1
F
A
4
18
4.6
19
0
21
5.1
22
30
0
1.7
23
100
0
25
1.2
3.3
2K +-1%
2.2K
28
4.9
0.1 F
0
R2633
BIAS
27
R2634
REV
26
4.3
4.3
MOTOR DRIVER IC
IC2602
BA5813FM
1
RVCC
REG-B
REG-P
24
1.8
R2627
2.2 F
R2625
C2611
RGND
IN4
IN3
MUTE2
20
8.9
C2629
5.1
2
LOCONT
MUTE1
IN1
5.1
3
FWD
2.3
4
W262
17
4.5
16V 100 KA
C2639
0.001 B
C2625
1 F
(21-25)
C2621
2.2 F
(21-25)
100
R2628
5.1
5
IN2
PAEVCC
VOL(-)
2.0
6
1.7
2
4.3
REG.
Q2605
2SA1213_Y
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
R2636
PCB130
VMA249
ARE
4.7
CAUTION: DIGITAL TRANSISTOR
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
C2612
0.1 F
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
H-1
5
FROM/TO SYSCON1
C2634
2.3
C2628
VCC
0.1 F
SCL
ASLCO
0.1 B
DMP
2
C2635
RESET
D_GND
GND
5.1
0.1 B
DMN
3
13
0
16V 100 KA
C2626
4
12
3.6
C2624
LMT
3.6
1.5K
GND
5
SCO
220P CH
C2632
VDD+5V_A
M+8V
M_GND
R2631
6
11
2.3
R2632
FMP
10
2.3
820
16
4.7
(21-25)
FMN
7
1.7
7
29
FROM/TO DECK
CP2601
04_6232_108_015
8
NC
100
R2626
15
POWVCC34
2.9
4.7
FFC(1.25P)
VRCK
FROM AUDIO/VIDEO
F (21-25)
0 8.9
8
2
CD2601 2H081006
1K
3
POWVCC12
VOL(+)
VO2(-)
VO2(+)
VO1(-)
VO1(+)
8.9
9
5.1
VCC
GND
DFCT
C2633
2.2
C2614
0
0
10
GND
1.3
0
11
VO3(-)
0.1
NC
4.6
12
VO3(+)
C2605
2.2 F
(21-25)
INVERTER IC
IC2601
TC7S04F
4.7
13
VO4(-)
NC
1
3.4
VO4(+)
TGL5
EQBC
4.7K
1.5
5
LDMN
2
R2635
0.1
C2619
1
6
47K
4.8
14
F
9
3.3
C2622
4
3
2.2
R2622
4.2
4
TOPN
3
0.1
R2637
0.001 B
2
2.2
DPB0
P2FP
17 VCKF
DPAC
64 P2FN
F (21-25)
62
F
DPDC
2.6
C2609 0.1 F
1
0.001 B
6
FEBC
1
R2618
0.001 B
1.7
C2620
4.8
5
4
FEB
TED
C2615
47K
5.9
1
LDMP
DPO0
P2DI
DMO
TEBC
C2631
1.7
C2608
R2616
C2604
2
5
VCC2
FED
FMO
C2630
19
61
2.3
3
FFC(1.25P)
100K
P2CI
FROM/TO DECK
CP2603
IMSA-9604S-06Z14
M_GND
NC
DFTN
64
JG2602
3.0
6
NC
P2BI
1
DVD/LD DRIVER
Q2603
HN1B01F_Y
TRO
W261
3.2
0
3.0
CD2603 2H060806
GND2
VCCS
2.2
63
R2617
2.2M
2.2M
R2612
JG2601
DK4001
TU2020R
3
TCC1
RFDC
VRA
EQB
EQF
MDI1
LDD1
P2AI
2.2
DVD
DECK
FOO
51
5.1
0
3
VDR
NC
RFRP
50
2.1
LDP2
RESB
2
1
RPZ
TEI
10K
1.7
GNDR
1SS368
MDN
OEC6067A
2.3
D2601
2
RPO
2.3
3.3
LD
0.022 B
2.3
IC2603
P1AI
2.3
4
GND
3
RF_AMP IC
2.3
2.3
1SS368
4
RPB
5.1
R2609
VCC
VCCR
FEI
R2639
3.3K
18
4.7
P1BI
0
D2602
F-
5
AFS
R2638
C2640
17
50
51
C2606
0.1
R2614
T+
6
4
4.7
F
C2602
7
5
1.6
2.9
VDD
T-
33
RPP
100
8
TEZI
1.7
34
P1CI
F (21-25)
F+
1.6
35
3.7
2.2
9
1.9
36
RF ON
VRFJL
B0
37
P1DI
VRO
10
38
1.8
C2617
C0
0 NC2.1 NC 5.1
39
RF OP
16V 100 KA
11
RFZI
0
LDP1
MIDI2
D0
40
1.8
LDO2
12
0.1 F
4.2
41
33 TEB
P2TN
A0
2.4
42
5.1
P2TP
13
2.1
43
SLCD1
49 P1FN
GND
E0
P1TN
49
14
0.1 F
0.1
52
F0
53
VCC
15
R2613
54
16
C2601
55
VREF
2.4
44
7
RFCD_DVD
2.3
56
17
C2603
57
GND
3.1
45
A+3V
C2623
2.3
58
VDR2
18
0.3
46
GND
VRFD
2.3
2.2 F
(21-25)
59
19
C2607
60
MDN2
P1FP
5.1
1K
20
4.7
R2641
LD2
2.2
0.1 F
6
F
R2608
5.0
47
P1TP
2.2
RF
2.2
48
FROM/TO DECK
VCC
0.001 B
2.2 F
(21-25)
C2616
C2618
3.3
R2611
2.2
JG2604
CP2602 (CD4001)
04_6232_123_015
R2630
5.1
JG2603
21
10K
1
A_GND
91
R2607
91
R2610
-1.2
7
22
FROM/TO DSP
47K
10K
23
A+3V
5.6K
R2629
C2613
0.1 F
1 F
(21-25)
C2610
R2624
3
2
4
5
-1.2
10
R2619
47K
CD/LD DRIVER
Q2604
HN1B01F_Y
0.5
5.1
R2603
8
R2621
47K
0
0
0
PROTECT 6
5
4
Q2602
SW.
HN1C03F_B
Q2601
KRC102SRTK
1
2
3
0
0 0.7 0.3
0
5.0
6
8
B
C
D
E
F
G
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
H
H-2
A
B
C
D
E
F
G
H
DPA4
DPA5
DPA6
DPA7
/BDE
/BCAS
/BWL
DPD8
DPD9
DPD10
DPD11
DPD12
DPD13
(DVD PCB)
8
DPD14
DPD15
DSP SCHEMATIC DIAGRAM
8
R2006
47K
C2019
0.1 F
C2025
A_GND
VRFD
C2060
A+3V
0.1 B
RFCD_DVD
SLCD1
C2004 0.001 B
RFZI
TEZI
4
3.3K
R2001
W208
0
C2005 0.001 B
FEI
TEI
RESB
RFRP
C2002
C2006
C2007
0.001 B
0.001 B
FOO
TRO
330P
CH
FMO
DMO
TEBC
FEBC
DPDC
EQBC
3
2.2 F
(21-25)
C2001
C2003 0.022 B
C2008 0.1 B
DFCT
VRCK
SCO
SCL
SCB
DMFG
ASLCO
30
0.3
29
0
28
0.6
27
0.6
26
0.6
25
0.6
0
24
23
VSS
4.6
A4
31
A5
4.6
A6
32
A7
0
35
A8
2.5
/DE
36
/UCES
2.5
/LCAS
VSS
37
NC
2.5
DQ9
38
DQ10
2.5
39
DQ11
0
DQ12
40
DQ13
2.5
DQ14
DQ15
DQ16
VSS
41
IC2002
1
2
2.5
2.5
3
2.5
4
2.5
5
5.1
6
2.5
7
2.5
8
9
2.5
2.5
10
0
13
NC
0
14
NC
4.8
15
3.9
16
0
17
NC
0.6
18
0.6
19
0.6
20
VCC
A3
A2
A1
A0
NC
/RAS
/WE
NC
NC
DQ8
DQ7
DQ6
DQ5
VCC
DQ4
DQ3
DQ2
VCC
DQ1
18K
5.1
0.6
21
5.1
22
C2049
10P CH
C2048
DPA3
DPA2
DPA1
DPA0
0.1 F
/BWU
/BWL
/BCAS
/BRAS
/BDE
C2031
/BRAS
/BWU
DPD7
DPD6
DPD5
DPD4
0.1 F
DPD3
C2040
DPD2
DPD0
DPD1
C2036
0.1 F
16V 100 KA
C2045
6
(21-25)
150P
CH
0
NC
1.7
1.7
1.7
1.0
C2024 100P CH 1.0
3.3
3.8
NC 2.5
3.3
W207
1.8
W206
1.8
3.3
0
C2027 2.2 F
1.7
R2016
100 (21-25)
1.7
1.7
C2023 0.1 B
1.7
0
1.7
1.7
1.7
1.7
0
W205
1.7
W204
1.7
0
1.7
0
1.7
R2026
2.2K
1.7
R2018
2.2K
3.3
R2004 10K
1.0
R2011
22K
R2021
10K 1.7
2.3
R2012
10K
R2022
10K 1.7
1.7
R2013
10K
R2023
10K 2.0
2.5
R2014
10K
R2024
10K 0.8
3.2
R2015
3.3K 1.6
0
1.0
0
0
R2010
C2026
1.3
1.7
10K
0.1 F
NC NC
NC
NC NC
132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 104 103 102 101 100 99
98 97 96 95 94 93 92 91 90 89
PVREF
VCOREF 133
LPFN
VCOF 134
LPFO
PVOO
SLCO1
SLCO2
TEST2
RFCD
RFDVD
AVDD
RFCT
RFZI
TEZI
AWIN
AVSS
FEI
TEI
RFSB
RFRP
AVSS
TEPI
EXTED
VREF
FOO
TRO
AVDD
AWCTL
FMO
DMO
TEBC
FEBC
DPDC
EQBC
ANMON
/DFCT
VRCK
VSS1
175 FGIN
SCO
176 ASLCP
SCL
SCB
88
87
DSP IC
IC2001
OEC6068A
46
45
BA6
BA5
BA8
BA4
BA7
VSS2
BA3
BA2
BA1
BA0
VDD1
BUFXG
DIGI
/PDAK
VDD2
PDCK
/PDRQ
/PSYC
PD8
PD7
PD6
PD5
VSS1
PD4
PD3
PD2
PD1
VSS2
PD0
VDD1
VMCK
SMCK
NC
NC
VDD2
MD7
MD6
MD5
MD4
MD0
MD3
/MDNT
MD2
MD1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44
FROM AUDIO/VIDEO
0 NC
0.7
DPA7
0.7
DPA6
0.7
DPA5
0.7
DPA4
0
0.6
DPA3
DPA2
0.6
0.6
DPA1
0.7
DPA0
3.2
W203
5.1
0
0
R2052
0
5.1
2.6
3.3
5.1
5.1
0.9
0.9
0.9
0
0.9
0.9
0.9
0.9
0
0.9
3.2
2.7
NC
2.6
NC
0.1
NC
0.2
NC
5.1
2.5
HD7
2.2
HD6
2.2
HD5
2.2
HD4
2.3
HD3
2.0
HD2
2.6
HD1
1.9
HD0
5.1
R2050
4.7K
D_GND
A_GND
D_GND
NC
NC NC
NC
NC NC NC NC NC NC
NC NC NC
NC NC
C2046
52
0.1 F
10K
TO MPEG
DVDSTB
DVDVALID
DVDSOS
DVDERR
DVDDAT7
DVDDAT6
DVDDAT5
DVDDAT4
DVDDAT3
DVDDAT2
DVDDAT1
DVDDAT0
C2050
3
0.1 F
C2051
FROM/TO SYSCON1
0.1 F
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
DNT
MWR
MRD
HA8
SVCEX
DISKWDI
FCSEAR
NC
10K
R2049 3.3K
C2041
0.1 F
1K
R2048
C2039
0.001 B
10K
R2045
C2037
0.1 F
100P CH
C2035
22K
R2002
0.015 B 4.7K
470K
0
C2038 R2047
R2044
1M
0.1 B
C2028
0.1 B
C2029
10K
100
R2019
0.1 F
R2008
0.1 F
C2021
0.1 F
C2020
0.1 F
C2015
C2010
1.7
4
2
R2046
R2042
1.9
0.1 F
C2014
SERVO SHUT DOWN
Q2001
2SC3326_B
5
GND
1 F
(21-25)
R2031
2
GND
VDD+5V
VDD+3.3V
SCLK2
C2047
1.7
1.6
100 0
1.6
3.2
1.6
1.6
0
0
2.3
1.0
3.2
0
3.2
3.2
0
0
1.6
3.2
1.6
1.3
0
1.2
3.2
0
3.2
0
3.2
3.2
3.2
0
0
3.2
0
0
3.2
0
5.1
0
5.1
2.4
1.7
5.1
5.1
RESET
GND
2.5
ASLCN
PDON2
ASLC0
PDOP2
DVSS
PDON1
R0
PDOP1
DVDD
PESP
DVR
PVSS
L0
PESV
DVSS
PPW
XVSS
CFC2
XI
CFC1
XO
VSS1
XVDD
PSE
PXI
PSS
PXO
EHAO
CKSE
EHAI
VDD1
PLCK
VSS1
VDD1
VPFC
NC
TEST0
NC
VLPF1
BO15
VLPF0
BO14
VSS1
BO13
MON0
VSS1
MON1
BO12
MON2
BO11
MON3
BO10
MON4
BO9
MON5
VSS1
RFSBOK
BO8
MON7
BO7
MON8
BO6
MON9
BO5
VDD1
BO4
NC
BO3
NC
BO2
TEST1
BO1
FLGA
BO0
FLGB
VDD2
VSS1
/BWU
/RST
/BWL
/MA
/BCAS
/MRD
/BRAS
/MWR
/BOE
/MCE
VDD1
45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
GND
R2005
42
W202
176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133
FROM/TO READ CHANNEL
5
2.5
0
C2018
2.2 F
(21-25)
43
W201
4.7K
47K
R2020
R2009
1 F
(21-25)
0.015 B
C2011
2.5
1.3
R2028
1K
0.2
R2030 2.2K
1.7
R2033 1K
1.7
R2035 3.3K
1.7
0
2.0
C2030 0.01 B
2.0 R2037 33K
1.7
R2039
10K
1.5
0
1.4
0
0
0
1.7
3.2
0
0
2.4
DPD15
2.4
DPD14
2.4
DPD13
0
2.4
DPD12
2.4
DPD11
2.4
DPD10
2.4
DPD9
0
2.4
DPD8
2.4
DPD7
2.4
DPD6
2.4
DPD5
2.4
DPD4
2.4
DPD3
2.4
DPD2
2.5
DPD1
2.5
DPD0
5.1
C2042 1 F
4.8
(21-25)
4.6
4.6
4.0
0.3
3.2
C2044 1 F
6
44
1K
7
D-RAM IC
R2036
R2038
330K
+-1%
R2029
33K
R2032
22K +-1%
+-1%
R2034
33K
+-1%
7
22K
R2027
MSM5416258B-30
0
NC
PCB130
VMA249
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
H-3
B
C
D
E
F
G
H
H-4
A
B
C
D
E
F
G
H
MPEG SCHEMATIC DIAGRAM
SPDIF
I45RSTX
GNDC
GND
10K
R4002
0.1 F
C4020
100
R4005
100
R4004
VDD+3.3VMPEG
7
50
51
52
53
54
55 56
57
58
59
60
0 3.0 3.2 3.0 3.0
61
62
63
64
3.1 3.1 1.7 0.1
65
66
67
68
0 3.7 3.2 1.4
69
70
71
72
0 1.3 3.2 1.8
73
74
75
76
77
78
79
0 1.2 1.4 1.7 3.2 1.6 1.1
VDDA
90
89
88
87
86
10K
R4006
99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120
98
91
GND
49
0 0.3 0.2 3.2 1.7 0.2 0.7
RDA4
48
RDA11
47
VDDP
46
RDA5
45
RDA10
44
RDA6
43
RDA3
GND
42
RDA9
41
0.5 0.5 0.5 3.2 0.5 0.5 0.5 0.5
VDDP
HACK
VDDP
85
VDDP
84
RDA13
83
RDA2
HIRQ
81 RDA12
97
92
RDA0
RDA15
HROY
40 GND
96
95
94
VCLK
93
VDDP
VSYNC
82
AGND
STBYX
RESTX
SCNENABL
VDDP
GND
VCLKX2
TEST
VDDAM
AMCLK
AGND
GPIO
SPDIF
VDDP
AOUT1
AOUT0
AOUT2
ALRCK
VDDP
ABCK
VDDC
GND
GPS0
GPS1
GND
DVDERR
DVDSOS
DVDSTRB
DVDVALIO
DVDREQ
DVDDA0
DVDDA1
DVDDA2
GND
HSYNC
81
4
5
6
7
8
9
10
11
12
13
14
15
16
GND
RDA7
3.2
3.4
NC
0
RDA14
GND
D
C4010
0.1 F
HRD
RDA8
MPGIRQ#
RDA1
VDDP
0
3.2
NC
5.1
VDDP
VDDC
PCLK
1.6
MRD
HCS
GND
1.7
HWR
RAMDQM
5.1
MPGCS#
HA0
VDDC
5.1
RAMWE
2.5
RAMCAS
HA1
MWR
HA1
RAMRAS
2.6
HA2
RAMCS1
HA2
HA3
FI
VDDP
2.5
VDDP
RAMCS0
2.4
HA3
VGND
HD0
GND
HA4
GND
RAD11
3.2
HD1
RAD9
1.9
HD0
C4008
0.1 F
VDDP
RAD10
2.6
VDDIP
HD2
VDDP
HD1
HD3
RAD8
2.0
RAD0
2.3
HD2
CSYNC
CVBS-G-Y
ZR36732
GND
HD3
HD4
MPEG IC
IC4001
RAD7
C4007
16V 100 KA
HD5
RAD1
2.2
VDDIP
RAD6
HD4
Y-R-V
CVBS-C
RAD2
HD15
HD14
HD13
HD12
HD11
HD10
HD9
HD8
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
HA4
HA3
HA2
HA1
MWR
MPGCS#
MRD
MPGIRQ#
I45RSTX
V_SYNC
GND
2.2
HD6
C-B-U
VDDD
VOOP
16V 100 KA
HD5
HD7
RAD5
FROM/TO SYSCON1
3.2
C4004
1N4005-EIC
2.8
VDOP
RAD3
3.9 1/4W
D4001
HD6
HD8
17
2.2 F
(21-25)
2.5
VGND
18
R4009
HD7
GND
19
C4003
RSET
20
3.2
HD9
21
HD8
3.2
VGND
22
VIN
0
1.7
4
2.5
2.5
23
GNDC
Vref
5
0.1 F
VGND
VDOC
24
VSS
HD9
1.7
VREF
HD10
25
EXT
+
C4006
3
GND
26
2
3.2
ON/OFF
1
VOUT
2.5V REG.IC
IC4002 S-816A25AMC
0
27
2.0
HD10
2.5
AIN
ICEMODE
28
2.5
0
HD11
29
GNDP
HD12
30
2.2
31
HD11
GND
32
2.1
HD13
33
HD12
PLLCFG
34
2.0
VDDC
HD14
35
HD13
HD15
36
2.8
GCLK1
37
3.2
HD14
HTYPE
38
2.5
2.6
39
REG
Q4001
2SA1213_Y
0.1 F
40
6
3.2
X0
PLLCFG0
120 GCLK
1 H0RD
RAD4
HD15
C4005
DVDDA3
VDDP
DVDDA4
1
HWIO
3.2
DVDDA5
DVDDAT7
DVDDA6
3.2
2
0
DVDDAT6
3
DVDDAT5
IDLE
DVDDAT4
DVDDA7
NC
NC NC
NC
NC
NC
NC
NC
0 1.8
0 1.6
0 1.7 3.2
0
0 1.7 3.2
0 5.1
0 3.2 1.7
0 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0.9 0 2.6 3.3 5.1 5.1
0 0 1.7 1.6 3.2 1.6 0
0 1.1 3.2
160 159 158 157 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121
DVDDAT3
3
GND
DVDDAT1
DVDDAT2
4
GNDP
MPEG+1.8V
DVDDAT0
5
53
4.7K
DVDERR
7
8
R4010
DVDSOS
DVDVALID
G+6DB
ALRCLK
ABCLK
DVDSTB
GNDA
100
R4003
DVDERR
DVDSOS
DVDSTB
DVDVALID
DVDDAT0
DVDDAT1
DVDDAT2
DVDDAT3
DVDDAT4
DVDDAT5
DVDDAT6
DVDDAT7
FROM DSP
ASDATA0
(DVD PCB)
GNDA
8
54
2.3
1.7
NC
0
B8502
FROM/TO AUDIO/VIDEO
FCM2012H-102T04
GCLK
GCLK1
VDD+3.3V
SPDIF
55
2.5
1.7
3.2
ABCLK
0
3.2
47K
ASDATA0
G+6DB
DAC_A
DAC_B
DAC_C
DAC_D
1.0
NC
0
GND_A
0
GND
R4011
1.2
1.2K +-1%
0
0.9
56
0.8
57
DAC_C
5
DAC_B
3.2
0.8
58
0.7
59
DAC_D
DAC_A
0
R4012
0.3
NC
3.2
22K +-1%
R4013
3.2
1.2K +-1%
0
FROM/TO MEMORY
1.6
NC
3.0
NC
3.2
MA4
MA3
MA5
MA2
MA6
MA1
MA7
MA0
MA8
MA10
MA9
MA11
MCS0#
MCSO#1
MRAS#
MPCLK
MCAS#
MWE#
MDQM
MD8
MD7
MD9
MD6
MD10
MD5
MD11
MD4
MD12
MD3
MD13
MD2
MD14
MD1
MD15
MD0
VDD+3.3VMPEG
C4029
10V 1000 YK
3.2
C4031
1.6
NC
1.3
0.1 F
MD0
0.9
MD15
3.2
1.3
MD1
1.2
MD14
0
1.4
MD2
2.4
MD13
3.2
C4033
1.2
0.1 F
2.1
MD3
MD12
80
0
D
3
GND
2
PCB130
VMA249
MD4
MD11
MD5
MD10
MD6
MD9
MD7
MD8
100
R4001
MPCLK
MDQM
MWE#
MCAS#
MRAS#
MCSO#1
MCS0#
MA11
MA10
MA9
MA8
MA0
MA7
MA1
MA6
MA2
MA5
MA3
4
0.1 F
C4012
2
MA4
6
ALRCLK
0.1
R4015
1
1
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A
H-5
B
C
DIGITAL AUDIO SIGNAL(PB)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
F
G
H
H-6
A
B
C
D
E
F
G
H
MEMORY SCHEMATIC DIAGRAM
8
R4021
10K
R4022
10K
R4023
10K
R4024
10K
R4025
10K
R4026
10K
R4027
10K
R4028
10K
R4029
10K
R4030
10K
R4031
10K
(DVD PCB)
8
7
7
0
A9
BS
A8
A10
A7
A0
A6
A1
A5
A2
1.7
HA8
2.4
HA7
2.9
HA6
2.8
HA5
2.6
0.5
0
A4
VSS
A3
VCC
13
32
A7
A0
A6
A1
A5
A2
A4
A3
VSS
14
15
31
30
NC
4.8
0
NC
0.4
2.6
HD8
1.6
HD0
1.8
MRD
1.6
RAS
2.5
HA1
2.6
HA2
2.5
HA3
2.4
HA4
MA0
0.4
HD1
WE
MA10
MA1
0.4
0
MA2
FLASHCS
0
MA4
A8
5.1
16
MA11
0.6
VCC
MA3
48
1
47
2
3
4
5
6
7
8
9
10
WEX
11
5.1 MWR
VCC
RPX
12
5
5.1
0
NC
DQ11
DQ3
DQ10
DQ2
A18
DQ9
A17
DQ1
A7
DQ8
A6
DQ0
A5
OEX
A4
GND
A3
CEX
A2
A0
A1
NC
13
0.5
0.6
DQ4
NC
14
0.5
MCSO#1
0.5
NC
0.2
NC
15
MA5
0.5
3.0
HD9
2.5
NC
1.8
NC
16
MA6
0.2
CSX
/RAS
2.0
DQ12
1.4 HA19
17
MA7
0.2
NC
/DE
HD2
0
NC
RY/BY
1.3 HA18
2.4 HA8
2.9 HA7
2.8 HA6
2.6 HA5
2.4 HA4
2.5 HA3
2.6 HA2
NC
17
0.2
NC
/WE
29
5.0
/UCES
28
38
13
15
16
17
4.9
NC
18
3.2
UCAS
DQ5
19
MA3
MRAS#
2.0
2.2 HA9
20
0.5
3.1
NC
HD10
A8
NC
0
/LCAS
2.3
DQ13
21
MA2
MCAS#
4.9
NC
HD3
2.5 HA10
22
0.4
RASX
CKE
3.2
LCAS
0
NC
2.2
A9
23
MA1
0
NC
HD11
DQ6
6
24
0.4
MWE#
18
MA0
3.1
19
0.4
MDQM
20
MA10
0
46
5.1
3.2
45
HD7
44
2.5
2.2
43
DQ8
DQ9
HD4
2.3 HA11
42
1.6
2.1
A10
41
MD7
HD12
DQ14
40
HD6
2.3 HA12
39
2.8
A11
38
1.1
DQ7
DQ7
37
MD6
DQ6
DQ10
2.2
2.1 HA13
36
1.3
DQ11
HD5
A12
35
4.5
2.1
DQ15
34
HD9
0
HD13
3.1 HA14
33
HD5
2.7
A13
32
2.2
HD6
GND
31
2.0
2.8
2.4 HA15
30
HD10
MD5
HD14
A14
29
2.2
2.5
BYTE
28
1.1
HD11
HD7
1.9 HA16
27
HD4
8
2
7
2.2
9
3
4
5
6
5.1
HD3
3.0
A15
26
1
44
43
42
41
4
5
7
8
9
10
12
2.3
HD2
HD15
A16
25
1
2
50
49
48
47
44
43
42
41
DQ5
2.0
MD4
OE
MA8
VCC
DQ12
HD1
21
VSS
VCC
2.6
22
A3
VSS
27
A4
DQ4
26
A2
19
0
A5
20
0.5
A1
1.7
21
MA4
A6
MA11
22
0.5
A0
0.6
23
MA5
A7
DQ13
25
MCS0#
24
0.5
A10
DQ3
24
3.0
25
MA6
32
0.5
31
MA7
A8
30
0.2
BS
29
MA8
A9
28
0.2
DQ14
23
MRAS#
MA9
MA9
DQ2
1.0
5.1
HA1
2.5
4
3
3.2
C4045
C4041
C4037
0.1 F
1K
CSX
2.1
R4007
NC
3.0
18
RASX
3.2
CASX
CLK
19
0.2
NC
CKE
1.7
WEX
20
MCAS#
0
21
3.1
UDQM
LDQM
22
MWE#
NC
23
3.1
VCCQ
VCCQ
24
3.2
CASX
HD12
3.3
MDQM
17
1.7
DQ7
14
0
NC
MDQM
18
60
2.1
HD8
MPCLK
MPCLK
DQ8
25
14
0
15
CLK
WEX
HD13
DQ15
HD0
MD7
16
36
10K
35
R4020
UDQM
34
10K
0
MDQM
33
10K
R4019
LDQM
NC
DQ6
5.1
1.9
10
1.1
DQ9
1.1
1.7
5.1
3.2
MD6
3.3
10K
R4018
37
0
NC
10K
MD3
11
MD8
VSSQ
VSSQ
40
1.6
DQ5
DQ10
37
11
1.1
MD9
DQ4
DQ11
39
1.1
0
3.2
2.8
DQ1
40
0
HD14
DQ16
39
MD5
2.6
38
1.1
1.3
36
VCCQ
1.4
VCC
37
MD4
35
VCCQ
MD2
VSS
36
1.1
VCCQ
VCCQ
HD15
0
3.2
3.2
DQ3
1.1
HA17
MSM5416258B-30
0
0
MD3
3.2
0.1
DQ12
34
DQ7
MD1
6
1.8
46
MD12
VSSQ
VSSQ
DQ2
33
DQ8
1.1
0.1 F
D-RAM IC
IC4005
35
3.2
12
DQ6
DQ1
DQ14
DQ13
32
1
2
3
4
1.1
13
42
41
40
DQ9
39
1.1
MD8
VSSQ
38
0.2
MD9
DQ5
VSSQ
MD0
MD2
MD10
DQ10
DQ0
DQ15
45
1.1
31
DQ4
1.2
MD13
30
DQ11
1.1
0
29
VCCQ
1.3
28
VCCQ
MD14
27
DQ3
0.5
26
DQ12
MD15
0
5
DQ2
0
6
50
49
48
47
46
DQ13
3.2
MD1
7
0
VSSQ
1.2
8
1.1
VSSQ
VCC
VSS
FLASH IC
IC4006 MBM29F800BA-55
C4044
MD0
9
MD10
DQ1
1.2
10
1.2
DQ14
45
MD11
DQ0
44
3.2
DQ15
MSM56V16160F-8
3.2
MD11
MA4
MA3
MA5
MA2
MA6
MA1
MA7
MA0
MA8
MA10
MA9
MA11
MCS0#
MCSO#1
MRAS#
MPCLK
MCAS#
MWE#
MDQM
MD8
MD7
MD9
MD6
MD10
MD5
MD11
MD4
MD12
MD3
MD13
MD2
MD14
MD1
MD15
MD0
VDD+3.3VMPEG
0.1 F
0.1 F
R4034
W406
0
(21-25)
2
C4048
220P CH
MEMORY_3.3V
15uH
D
16V 100 KA
L4001
10K
C4038
GND
1.8
MD12
FROM/TO MPEG
2
1.3
MD13
0
VCC
43
0
R4017
3
1.1
MD14
R4016
4
1.7
MD15
MSM56V16160F-8
VSS
27
5
IC4003
0
26
6
SD-RAM IC
IC4004
SD-RAM IC
LCAS
UCAS
OE
RAS
WE
FLASHCS
MRD
MWR
HD8
HD9
HD10
HD11
HD12
HD13
HD14
HD15
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
HA19
HA18
HA17
HA16
HA15
HA14
HA13
HA12
HA11
HA10
HA9
HA8
HA7
HA6
HA5
HA4
HA3
HA2
HA1
3
FROM/TO SYSCON1
FROM AUDIO/VIDEO
VDD+5V
W403
0
PCB130
VMA249
(32-16)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
A
H-7
B
C
D
E
F
1
G
H
H-8
A
B
C
D
E
F
AUDIO/VIDEO SCHEMATIC DIAGRAM
G
H
(DVD PCB)
8
8
FROM POWER
FROM/TO SYSCON1
28
1
ZERO
LRCK
25
4
1.6
FILTB
BCLK
24
5
1.6
AVDD
6
1.1
SDATA
23
R8546
OUTL
3.2
C8542
R8525
C8517
5.1
2.4
0
21
0
FILTR
DGND
2.4
16V
6
VDD+5V
5.1
5.1
0
61
2.5
R8515
2.6
VDD+5V
18
XOUT
LF1
XIN
LF0
SCLK1
PGND
C8523
2.9
1.9
R8520
0.0018 M M
C8524
680
0.0033 M M
0
AUDIO GAIN CONTROL
Q8511
KRA102SRTK
0
0.1 F
0
5.1
C8529
R8530
19
10
0
16V 100 KA
20P CH
27MHz HC-49-US
2.4
C8539
33P CH
150
AGND
17
C8504
MCLK
16
C8503
2.5
X8501
11
R8508
2.3
12
33P CH
DUTR
KA
100
W858
13
SCLK2
PVDD
C8520
5
W869
(21-25)
0.0033 M M
6
P.CON+D5V
7
P.CON+D5V
8
GND
9
P.CON+3.3V
10
P.CON+3.3V
11
GND
12
SPDIF-134
13
6
L8507
63
64
AUDIO_R
5
5.1K +-0.5%
9.2
KA
4.4
CIN
COUT
27
25
C8515
VIDEO BUFFER
Q8501
KTA1504S_Y_RTK
4
10K
0
NC
3.9
C8518
PS1
YCMIX
26
5.7
3
R8518
CLP
VEE2
YIN1
YOUT1
23
6
4.8
VEE2
22
MUTE2
21
20
9
VEE2
11
CBIN
CBOUT
19
10
GND
D/S
CRIN
CROUT
VEE1
VEE2
PS2
17
12
0
13
C8514
R8523
5.1
W861
0
0
R8540
5.0
13
4
12
11
10
9
8
GND
7
AUDIO-L
6
GND
5
AUDIO-R
4
ZERO
3
DVD RESET
2
RGB-H
1
3
+-1%
0
R8541
3.9
69
CB
75 +-1%
0.1
NC
+-1%
D8501
1SS226
0
D8502
1SS226
2
D8503
1SS226
2
D8504
1SS226
2
D8505
1SS226
2
CR
2
2
8.2
3.9
0
1
3
1
3
1
3
1
3
1
3
W866
0 (21-25)
W867
F
16
70
R8542
3.9
75
0
15
RGB CTL
Q8507
DTC114EKA
68
Y_2
C8537
R8507
75 +-1%
75 +-1%
0.9
DAC_B
R8504
67
Y_1
0
16V 10 KA
VIDEO BUFFER
Q8505
KTA1504S_Y_RTK
14
GND
0.1 F
C8508
4.4
1.5
15
2H0I1801
0.01 B
18
4.5
16V 10 KA
0
GND
CVBS
CD8002
16V 100 KA
C8507
VIDEO BUFFER
Q8503
KTA1504S_Y_RTK
16
DVD Y(G)
75
C8516
4.1
2.2K
R8509
YOUT2
14
0.8
16V 10 KA
YIN2
17
GND
C8528
0
RGBON
4.7
2.2K
R8506
R8502
75 +-1%
VEE2
C8513
VIDEO BUFFER
Q8502
0 KTA1504S_Y_RTK
1.5
DAC_C
MUTE1
GND
C(CVBS)
DVD V(R)
10K
5.7
2
7
6.8
8
2.2K
R8505
R8519
18
GND
R8522
FFC(1.25P)
Y(G)
DVD U(B)
0
75 +-1%
1.5
0.8
66
CVBS
W856
16V 10 KA
DAC_D
680
C
10V 1000 YK
C8512
3
R8524
75 +-1%
0
65
150 +-1%
0.1 F
24
0
R8510
5.0
16V 10 KA
C8522
VOUT
4
5
6
8.2 9.0 9.2
8.2
0.1 F
2
VIN
CP8502 (CP8002)
IMSA-9604S-18Z13
REG.
Q8508
HN1C03F_B
16V 100 KA
VCC2
28
1
VCC
5
R8501
75 +-1%
DAC_A
5.4
2.2K
R8503
W851
1.3
8.9 8.2
3
2
1
VIDEO DRIVER IC
IC8504
MM1540AFBE
C8511
0.7
FROM/TO DVD IN/OUT
VCC+9V
F
C8506
0 (21-25)
0.1
0.1
2.3
100
8.2
GND_A
5
P.CON+9V
ZERO
L8501
680
4
P.CON+9V
W5T29X7.5X19
RSTOX
2.4 5.1K
+-0.5%
R8526
R8521
3
GND
GND_A
16V 100
ALRCLK
ASDATA0
G+6DB
DAC_A
DAC_B
DAC_C
DAC_D
GND
R8532
AUDIO_L
C8525
0.0018 M M
C8526
2
GND
C8505
4
R8548
62
1
RX
W854
0.1 F
C8501
GND
OUT
5
5.1
VDD+3.3V
GCLK
GCLK1
SPDIF
ABCLK
3
IN_A
IN_B
0
2
C8510
5.1
1
2.2 F (21-25)
2.3
VCC
FROM/TO MPEG
IC8501
2INOUT AND GATE IC
M_GND
M+8V
TC7SH08FU
TO READ CHANNEL
FCM2012H-102T04
TX
(21-25)
5.1
100
B8503
SPDIF
2.4
16V 100 KA
14
3.4
SCLK2
15
R8544
SO2
5.1K +-0.5%
AUDIO GAIN CAONTROL
0
Q8513
2SC3326_B
100
VDD+3.3V
7
CD8501(CP8001) CU2D3001
SI2
C8543
B8501
A_GND
GND
D_GND
GND
FCM2012H-102T04
TO DSP
SCLKO
10
AUDIO GAIN CONTROL
Q8509
KTC3875S_Y_RTK
5.1
R8545
C8502
9
2.6
NC
20
0.1 F
TO MEMORY
R8527
22
7
AGND
AUDIO GAIN CONTROL
0
Q8510
KRA102SRTK
5.1
0
C8521
8
10K
R8511
C8509
DVDD
5
FROM/TO DVD IN/OUT
W857
5.1K +-0.5%
AUDIO GAIN CONTROL
Q8512
2SC3326_B
R8531
2.4
2.4
100
5.1
4
P.CON+9V_A
W855
C8519
0.1 F
ASDATA0
3
GND
MOTOR_GND 6
0
16V 10 KA
ABCLK
P.CON+5V_A
15uH
RSTX
10K
5.1
ALRCLK
RGBON
RSTX
4
G+6DB
10K
4.7K
GND
AT+5V
DACSOX
DACDATA
DACCLK
0.01 B
R8514
0
2
GND
10K
RSTX
MUTE
1
P.CON+5V_D
10K
100
R8517
CLATCH
R8529 R8528
VDD+5V
VDD+5V_A
5.1
5.1
(CP503) CD8502
CU262501
10K
DACSOX
27
220
R8513
CDATA
CCLK
26
SO2
VDD+3.3V
ATDIO DAC/PLL CLOCK GNERATOR IC
IC8503
AD1959YRSRL
5.1
2
DACCLK
SI2
AUDIO_GND
100
R8512
3
M+8V
M_GND
RSTOX
7
R8516
DACDATA
0
PCB130
VMA249
RGBON
1
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A
H-9
B
C
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
F
1
DIGITAL AUDIO SIGNAL(PB)
AUDIO SIGNAL(PB)
PLAYBACK LUMINANCE SIGNAL
PLAYBACK COLOR SIGNAL
PLAYBACK VIDEO SIGNAL
G
H
H-10
A
B
C
D
E
F
G
H
SYSCON1 SCHEMATIC DIAGRAM
(DVD PCB)
DACDATA
HA7
2.8
W102
DVCC
DSPSI
DVSS
DSPCK
D15
TXD
D14
RXD
D13
RTS
D12
DVCC
D11
VSYNC
D10
WAITX
D9
AM0
D8
CLK
DVCC
D7
TEST0
35 NC
73
D6
D3
36 CLVCC
D2
D1
D0
DVSS
RDX
WRX
NC
NC
NC
NC
NC
DVCC
D4
NC
RASOX
ROMC5X
ZRC5X
TBFC5X
SVCEX
D5
DVSS
CLVSS
2.0
2.5
1.9
0
100 1.7
R1060
5.1
5.1
100 5.1
0
3.7
5.1
5.1
1.0
4.8
5.1
5.1
5.1
0
5.1
5.1
5.0
1.6
NC NC NC NC NC
NR1005 CAY16-101-J-4R
0
W104
X1001
CSTCC9M00G
1
NC
R1058
0
RSTOX1
NC
NC
NR1002
CAY16-101-J-4R
71
W103
5.0
5.1
5.1
NC
5.1
NR1001 CAY16-101-J-4R 5.0
NC
0
5.1
5.1
5.1
5.1
0
2.2
0
37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72
4.7K
NR1007
2.1
HA12
C1028
HA13
0.1 F
3.1
HA14
2.5
HA15
5.1 CAY16-101-J-4R
NR1008
1.9
HA16
1.7
HA17
1.2
1.4
HA19
C1029
4.7 CAY16-101-J-4R
NC
4.7
NC
5.1
NC
5.1
NC
0
5.1
0
C1019
C1020
NR1009
HD15
2.8
HD14
2.2
16V 100 KA
C1021
HD13
2.1
HD12
NR1010
4
0.1 F
HD11
2.0
HD10
2.5
1.6
HD9
C1022
16V 100 KA
HD8
5.1 CAY16-101-J-4R
NR1011
2.5
HD7
2.8
HD6
22K
C1018
2.2
HD5
0.1 F
2.2
HD4
R1095
RSTX
2.3 CAY16-101-J-4R
5.1
5.0
8
5.1
7
FROM/TO AUDIO/VIDEO
5.1
6
5
M+8V
M_GND
VDD+3.3V
5.1
2
3.2
V_SYNC
3
5.1
VDD+5V_A
RSTOX
SI2
SO2
DACSOX
DACDATA
DACCLK
RGBON
4
0
VSYNC
2
RSTX
5.1
AT+5V
GND
2
HD3
HD2
HD1
HD0
MRD
MWR
0.1 F
C1013
RAS
MPGCS#
SVCEX
WE
1K
OE
5.1
C1030
RGBON
R1039
R1038
1K
D1/ASP_COTROL
Q1004
0
DTA114EKA
UCAS
D1/ASP_CONTROL
Q1003
5.1
DTA114EKA
LCAS
4P CH
0
FLASHCS
5.1
C1011
3
VDD+5V
1
3
5
0.0022 B
2.6 CAY16-101-J-4R
2.1
PUDET2
LSRDVD
LVL
DMFG
LDMN
LDMP
RESET
TOPN
TCLS
LMT
PUDET1
16V 100 KA
HA18
V_SYNC COTROL IC
IC1006 TC7W241FU
TEST1
2.3
FROM/TO READ CHANNEL
A2
DSPSO
HA11
Y1
DVSS
2.3
Y2
NC
DSTBX
HA10
G
SVINTX
HA9
2.5
VCC
NC
2.3
6
C1027
16V 100 KA
HA8
A1
A21
NC
NR1006
2.4 CAY16-101-J-4R
/G
DISKWOI
73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108
A5
A4
A3
A2
A1
A0
DVCC
SCLK
SO
DACSOX
PLLCSX
NC
NTPLX
NC
LOMP
LOMN
SVRSTX
I45RSTX
DVSS
SBADD
NC
A20
0
3.0
0
GND
2.6
2.4
2.5
2.6
2.5
0.4
5.1
5.1
5.1
5.1
5.1
0
5.1
0
0
5.0
5.1
5.1
5.1
0.3
0
2.7
5.0
1.7
FCSERR
PUDET2
TOPN
PUDET1
TCLS
LSRDVD
A19
IC1001
OEC6069A
TBFINTX
VDD+5V
NR1004 CAY16-101-J-4R
NR1003 CAY16-101-J-4R
100
R1050
100
R1049
R1047
10K
2.2K
R1044
1K
1K
R1042
R1041
1K
R1040
2.4
5.1
5.1
5.1
PUHQME
BOOTX
VREFH
VREFL
MICON IC
CTS
R1099
GND
0.1
PCB130
VMA249
F
CAUTION: DIGITAL TRANSISTOR
1
1
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A
H-11
HA6
HA5
HA4
HA3
HA2
DACCLK
DACSOX
HA1
LDMP
LSRDVD
LDMN
I45RSTX
LVL
FCSEAR
PUDET2
TOPN
PUDET1
TCLS
LMT
10K
10K
R1037
5.1
5.1
0
ADVSS
ADVCC
1
2
3
4
A18
WEOX
5.1
DVSS
NC
NC
0
1.8
A17
OEOX
0
VSYNC
NC
UCA50X
2.5
NC 0
A16
LCA50X
5.1
DVCC
DMFG
S1X
5.1
NC
S2X
10K
A15
CVSX
5.1
R1029
A14
NC
RGBSX
10K
I45INTX
2.4
4.7K
R1024
4.7K
R1021
10K
5.1
R1028
A13
NMI_INH
5.1
0
10K
10K
R1036
5.1
A12
WP
DVCC
1K 5.1
PROMDA
NC
SI2 R1031
A11
RESET
1K 5.1
NC
R1018
RESET
OUT
5.1
SO2 R1030
A10
PROMCK
AM1
5.1
NC
5.1
A8
A9
144 DAVCC
X2
5.1
3.2
RSTOX
5.1
0
5.1
0
0
0
5.1
R1013
10K
0.001 B
C1010
NC
143 DAVSS
DVCC
DVSS
10K
109 A6
5
0
NC
3.0
R1005
DAOUT1
DVSS
6
5.1
0
NC
DAOUT0
A7
7
0.1
DAREFL
4P CH
C1012
2
RSTOX1
8
10K
5.1
FROM/TO MEMORY
3
R1033
0.001 B
5.1
5.1
4
C1025
16V 100 KA
36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
10K
R1022
10K
R1015
R1017
2.2K
R1002
NC 0
5.1
DAREFH
X1
4.7K
R1014
5.1
0
MPGIRQ#
LCAS
UCAS
OE
RAS
WE
FLASHCS
MRD
MWR
HD8
HD9
HD10
HD11
HD12
HD13
HD14
HD15
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
HA19
HA18
HA17
HA16
HA15
HA14
HA13
HA12
HA11
HA10
HA9
HA8
HA7
HA6
HA5
HA4
HA3
HA2
HA1
NC
144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109
4.7K
NC 0
5
0
NC NC NC NC NC
R1025
FROM/TO MPEG
DMFG
3
5.1
8
7
6
HD15
HD14
HD13
HD12
HD11
HD10
HD9
HD8
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
HA4
HA3
HA2
HA1
MWR
MPGCS#
MRD
MPGIRQ#
I45RSTX
V_SYNC
GND
R1034
100
2
10K R1035
R1027
4
GND
5.1
IN_B
100
VCC
RESET AND_GATE IC
IC1005 TC7S08F
C1007
0
0.1 F
W101
C1003
R1026
1
5.1
C1009
SDA
5.1
5.1
5
4.7K
SCL
A3
0.1
R1016
A2
8
TEST
7
A1
5.1
6
0
VCC
5
0
2
0
A0
3
HD7
HD6
HD5
HD4
HD3
HD2
HD1
HD0
DISKWDI
FCSEAR
SVCEX
MRD
MWR
DNT
HA8
7
0
4
FROM/TO DSP
1
EEPROM IC
IC1002 S-24C01BFJ-TB
0.1 F
5.1
IN_A
2.2K
2.2K
R1012
2.2K
R1003
R1001
8
B
C
D
E
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
F
G
H
H-12
R146
FE_HEAD(GND)
2
FE_HEAD(HOT)
B
0.1 B
C165
4.7K
SINGLE SW IC
IC102
TC7SB384FU
W882
W881
W852
F
F
0.01
C201_1
C177
C173
0.1 F
0.01 B
B
C170
0.1
C169
50V 4.7 KA
12uH
0.001 B
24
25
26
0
C175
0.01 F
2.0
4.9
5
6.3V
0.1
30
0.01 F
C193
4.9
C194
3.0
47 KA
4.9
L116
4.9
P.CON+5V
100uH 0305
0
0
0
16V 10 KA
3.0
C187
34
C183
4.9
2.8
SWD_VIDEO
C181
1
B
4
FRONT_V_IN
C191
50V
TU_V_OUT
1 KA
KA
0
0
5.15
5.12
COMPOUND
Q113
DTC143EKA
C179
4.7K
CH
COMPOUND 0
Q110
DTC143EKA
0
29
2.8 1.9 2.8
R132
91P
0
2.6
AGC
28
50V 3.3 KA
C174
B
C172
1
F
27
0.01 F
C186
50
49
48
47
46
39
38
37
36
35
YGND
23
0.1
0.1 F
33
LPF
R
22
C171
5.6K
47P CH
ATT
(-10dB)
0
1.9
16V 10 KA
21
ATT
(-10dB)
6
0
C184
P
20
C168
0.1 F
C166
B
R127
C188
C164
45
44
43
42
41
40
19
ATT
(-10dB)
SW15 CLAMP
CLAMP
18
CH1
CH2
32
SW12
Y LPF
R P
SW115
VIDEO AGC
CH3
SW14
YNR
REC
DO
DO
31
R
SYNC
50V 2.2
P
R
1/4W
0
47P CH
P
2.2M
1/4W
L111
VCC=5V
FBC/ALC
SW10
17
0.1
6.8K
C162
MODE
CONT CCD
10
0.3
3
820
R121
22K
C151
0.018 B
0
5.5
0
COMPOUND
Q108
DTC143EKA
R111
4.7K 0.7
2
0
0
PB SW
Q107
KTC3198
0
S.DET-H
1SS133
NA_REC-H
D101
0.5
7
PICTURE_CTL
0.7
L110
4.7K
4.9
PB SW
Q106
KTC3198
100uH
0305
4.9
470P CH
0
NORMAL_A_OUT
R110
P.CON+5V
5.6K
PB SW
Q105
KRA103SRTK
PCB010
VMA252
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
A
2.2K
C145
NORMAL_A_IN
220P B
P.CON+5V
COIL,BIAS OSC
L104
1616003
C115
4
100V 0.022 MMTV
5
3
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
H-13
16
REC
AGC DEL
PB ALC
4.86
R145
10K
R119
47K
R107
0.0047 B
15
R
D.E.
N.C.
5
6
2
10V 220 YK
10K
C109
100uH 0305
C106
0
10V 33 KA
NORMAL AUDIO
REC ST SW
Q102
KTC3203_Y
C108
NA_REC-H
2.2K
0
1
C144
R120
R109
14
Y
CCD
P SW17
P
SW11
13
0.1 F
C150
1
R106
4.6
R101
W801
C189
CP103
TMC-T02X-E1
820P CH
TO
FULL ERASE HEAD
4.9
OSC
Q104
KTC3203_Y
C113
4.9
C111
4.6
AUDIO_PB
C192
6
AUDIO_REC
47P CH
5
6
CTL+
0.01 B
CTL+
L103
CTL-
4
R125
KA
C154
50V 4.7
12
R117
470P CH
C116
P.CON+5V
3
18K 1/4W
16V 10 KA
CTL-
0.01 B
AE_HEAD(+)
3.3
AE_HEAD(-)
2
R105
1
47 KA
6.3V
L112
B
0.022
C152
1K
100CT4R407
1
R115
C117
CP102
IMSA-9604S-06Z14
FEED BACK
CLAMP
VIDEO ALC
2.8 2.5 2.6 2.5 2.4 2.4 4.9 1.2 1.2 3.0 0.6 0.6 2.2 3.1 2.7 2.4 2.0 3.1 2.1 1.5 2.1
NC NC
R112
FROM/TO HEAD AUDIO CONTROL
C163
C167
B
C149
C148
0.47 B
50V 2.2 KA
0.1
11
16V 10 KA 180
3
2
10
9
SW16
R
NL NL
EMPH DE EMPH
220uH
8.2K
0
1
8
CCD
GND
SQUELCH
B.D
Y APA
DO EDGE
DET DELAY
SW9
R126
R114
C137
SW6
3 2
LMIT
WHAITH
N P
P
C
CCD
6.3V 47 KA
EP-L
X101
81
82
83
84
85
2.5
FO/DEV
ADJ
S-DET
YVCC
150P CH
EP-R
EP_COM
FM MOD
7
P
MAIN
DE EMPH
MAIN
EMPH
CARRIER
OFFSET
W.C/DC
1.5K
EP/LP-CH2 (L)
0
6
5
C.K
CLPH
CLPH
SW24
R
MAIN
CONV2
MAIN +
CONV1 SW22
P
SW23
R
R
P
P SW21
R
BPF
CLEAR SYNC
SW18
TRAP
SUB LPF
LAG LERD
LPF
R123
1
2.5
C142 0.22uH
EP/LP_COM
4
L109
EP/LP-CH1 (R)
2
SP-L
3
DELAY
7M HPF
VCA
BAND
A.GND GAP
APC
SW
DEMO
P SW2
R
PRE
AMP
REC EQ
0.22uH
3
MUTE
L108
SP-CH2 (L)
AVCC
C140
4
SP_COM
+
DLIM
1M HPF
SW4 SW5
L107
SP_COM
LEVEL DET2
R
PULSE
GEN
G
EQ
SQPB
+
2.5
270K
5
SP-R
R113
SP-CH1 (R)
SW39
2
SW26R
SW25
DL
SYNC.SEP.
C SQUELCH
CLOCK
DEIVER
B.E
S SQPB
DL
P
EQ
2.07
5.0
6dB AMP
7
1
C190
6dB AMP
R
FM
AGC
DET
DET
HF2
0.01 B
6
HF_COM
C129
HF2 (L)
0.01 F
HF_COM
7
+
1
C136
8
100uH 0305
HF1
6.3V 47 KA
HF1 (R)
2.5
-
CTL TRAP
HPF
FHTRAP
+
629
TRAP
R
0.1 F
TOC-C09X-A1
9
0.9
B
C128
CP101
1
A_MUTE/TRICK-H
L106
P.CON+5V
FROM/TO CYL
NTSC/PAL
N-P CONT
OUT
CCD
LPF
VCA
LEVEL DET1
P
ACC
DET
C161
C107
EE/VV_V_OUT
4
4.9
CH1
FROM
MESECAM
DET
LPF
R122
0
W860
MSECAM-M/AGC/S.DET
EP1
SW38 EP1
L SECAM
C156
4.9
2FSC
SW37
97
TO SUB MICON/OSD/VPS
B
REC
MUTE
P SW7
16V 10 KA
0.5
FRONT_V_IN
1
-
1/2
PHASE SW
C157
C131 0.01 F
SERIAL CONT
INTERFACE
COLOR
KILLER
ID DET
PB
APC
MIX
LEVEL C.K
ADJ
6.3V 22 KA
0.01 F 0
C122
EP-R
SW36 EP2
C155
FROM OPERATION/DISPLAY
0
SW31
CH2
C153
0.01 F C135
EP2
+
L SECAM
SW27
W869
0.01 F 0
C121
EP_COM
0
CVCC
KIL
SEP
HPF
COMP SW19
EP
VCA
SW3
REC ON
P.CON+5V
GND
B
C141
C134
CH1
SW35 SP1
HA VCC
C147
0305
REC
APC
2.06
2
4
FH SYNC
P SW20
ACC
R
2M LPF
+
16V 10 KA
22uH
DOWN
CONV.
SW28
SW29
SP
SW34
SW40
SP ON
EP-L
4PHASE GEN
50V 4.7 KA
5
0.01 F 4.9
C127 0.1 F
-
SW1EP ON
L105
P.CON+5V
FROM REGULATOR
2.2
PB/REC REC
DISCRI AFC
1/2
2FL VCO
SP1 SW30
CH2
0.001 B
0.01 F C133
0
0.022 B
CR DET 2FSC
+ SP2
SW33
6.3V 47 KA
3
DET
0.22uH
SP-R
0.01 F 2.2
C132
ME
SECAM
DET
C203
180P CH
2FSCVCO
COMP DET
SW32 SP2
91
HF_COM
2.2
92
C126
HF2
C124
93
6.3V 47 KA
SP_COM
2.2
0.01 F
86
C123
SP-L
HF1
ENV HPF
DET
HA GND
94
NORMAL_A_OUT
0
C159
KILLER
DET OUT
87
C120 0.1 F
NORMAL_A_IN
5P CH
C GND DO
X TAL VCO/OSD
88
50V 3.3 KA 0.9
ENV.DET
FROM/TO HI-FI/DEMODULATOR
2.4
0.1 B
C158
HEAD SW1
HEAD SW2 TANC
LIMITTER
89
C130
B
90
0.033
1.1
95
C125
5
96
V.H_SW
TU_V_OUT
2.2K
C204
NC
0 2.1 2.8 4.7 2.1 2.1 1.7 1.7 1.9 2.1 2.5 2.8 1.4 5.0 5.0 5.0 2.2 4.2 3.2 3.0 5.0 2.1 0.1 3.3 2.8 2.1 2.0 2.8 2.7 0
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
98
SWD_VIDEO
NC
FRONT_V_IN
6
0.001 B
Y/C/AUDIO/CCD
/HEAD AMP IC
IC101
HA118217F
2.6
100 99
FROM TUNER/JACK
0.001 B
C118
C119
H.SW
TP101
27K
C139
S.DET-H
0.01
MSECAM-M/AGC/S.DET
F
V.ENV
TP102
NC
CTL-
R116
W886
CTL+
100uH 0305
1
2
0.1
4
R118
ENV.DET
7
C146
W885
IIC_CLK
B
C143
IIC_DATA
R148
1K
4.86
L124
A_MUTE/TRICK-H
8
AMP
Q111
KTC3875S_Y_RTK
2.07
DUMMY_V.SYNC
SYNC
1.8K
2.8
C205_1
100
R144
P.CON+5V
EE/VV_V_OUT
IIC_CLK
H
0.01
NA_REC-H
3
(SD-22VB)
(VCR PCB)
100
V.H_SW
PICTURE_CTL
R135
FROM/TO VCR SYSCON
L113
Y/C/AUDIO/HEAD AMP
SCHEMATIC DIAGRAM
8
G
DUMMY_V.SYNC
F
IIC_DATA
E
R134
D
P.CON+5V
C
22uH
0305
B
2FSC
A
C
D
E
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
F
G
H
H-14
A
B
C
D
E
F
G
H
Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM
(VCR PCB)
1
FE HEAD(GND)
2
FE HEAD(HOT)
A
C
100
R135
17
SW15 CLAMP
CLAMP
18
19
P
20
21
R
23
24
1.8K
R148
1K
0.01 F
F
C201_1
0.01
C174
C175
0.1
0
91P CH
34
29
C194
0.01 F
P.CON+5V
100uH
0305
3.0
0
0
0
4
2.8
2.8 1.9 2.8
5
5.0
L116
4.9
30
SINGLE SW
IC102
TC7SB384FU
S807X S807Y
S808X S808Y
0.1
SWD_VIDEO
AGC
28
47 KA
C193
4.9
C181
1
FRONT_V_IN
C191_1
B
50V
COMPOUND
Q113
DTC143EKA
5.12
0
COMPOUND 0
Q110
DTC143EKA
0
0
3.0
50V 3.3 KA
B
C172
F
1
F
C171
R132
27
4.9
6.3V
46
44
37
38
26
0.01 F
C186
50
25
4.9
1
TU_V_OUT
KANP
3
0
4.2
50V
47P CH
220uH
C164
L111
0.1 F
35
YGND
22
4.7K
ATT
(-10dB)
LPF
0.1
C168
C166
5.6K
R126
0.1 B
6.8K
C162
150P CH
2.2M
1/4W
C188
1.5K
R122
C156
16V 10 KA
R123
R127
ATT
(-10dB)
0
5.0
16V 10 KA
SW12
ATT
(-10dB)
0.01 F
2.0
3.3K
Y LPF
R P
R
C183
4.9
C187
P
CH1
CH2
2.6
0
5.15
SECAM_IN
SECAM SW
Q109
KRC103SRTK
0.1 F
C161
820
47 KA
C151
0.018 B
0
6.3V
2.2K
C145
C157
10K
470P CH
22K
C144
43
40
R
SW115
VIDEO AGC
CH3
SW14
YNR
REC
DO
DO
33
P
32
SW10
2.8 2.5 2.6 2.5 2.4 2.4 4.9 1.2 1.2 3.0 0.6 0.6 2.2 3.1 2.7 2.4 2.0 3.1 2.1 1.5 2.1
NC NC
R117
VCC=5V
31
SW9
16
MODE
CONT CCD
FBC/ALC
MAIN
DE EMPH
15
REC
AGC DEL
PB ALC
P
SW11
14
D.E.
N.C.
NL NL
EMPH DE EMPH
SUB LPF
13
R
36
SW16
R
DLIM
MAIN
EMPH
CARRIER
OFFSET
W.C/DC
P SW17
Y APA
DO EDGE
DET DELAY
Y
CCD
39
C
CCD
P.CON SW
Q112
KRA103MAT
S806X S806Y
0
C184
12
41
42
FEED BACK
CLAMP
VIDEO ALC
0
1.9
16V 10 KA
11
R115
R109
B.D
CCD
GND
SYNC
0
R138
0
9
SQUELCH
6
10 1/4W
0
KA
1
8
C153
C142 0.22uH
0
3 2
6.3V 22 KA
2.5
FO/DEV
ADJ
S-DET
YVCC
SW6
7
LMIT
WHAITH
N P
5
4.86
R145
0.3
2.2
FM MOD
C155
0
16
5
C.K
CLPH
CLPH
SW24
R
MAIN
CONV2
MAIN +
CONV1 SW22
P
SW23
R
R
P
P SW21
R
BPF
P
CLEAR SYNC
SW18
TRAP
P
G
EQ
SQPB
LAG LERD
LPF
W869
2.5
DELAY
7M HPF
VCA
16V 10 KA
2.5
L109
4
0.22uH
3
APC
SW
DEMO
P SW2
R
BAND
A.GND GAP
49
48
+
CLOCK
DEIVER
B.E
1M HPF
REC EQ
47
R
CTL TRAP
HPF
FHTRAP
S SQPB
DL
P
EQ
SYNC.SEP.
C SQUELCH
LEVEL DET2
PULSE
GEN
ACC
DET
1/2
PHASE SW
DET
SW3
REC ON
MUTE
PRE
AMP
1
W882
W881
-
SW26R
SW25
DL
6dB AMP
47P CH
AVCC
2.07
2
4.84
45
P
6dB AMP
R
SW4 SW5
C205_1
0.1 B
0.1
C173
F
0.01 B
C170
W852
NTSC/PAL
N-P CONT
OUT
CCD
LPF
VCA
LEVEL DET1
C179
LPF
+
R144
P.CON+5V
EE/VV_V_OUT
1K
R130
C177
B
0.1
C169
50V 4.7 KA
C165
4.7K
DUMMY_V.SYNC
REC_IN
0.01 B
C178
IIC_CLK
IIC_DATA
100
R134
P.CON+5V
L113
C163
12uH
R125
C167
6.3V 47 KA
L112
KA
50V 4.7
C154
0.001 B
CVCC
SERIAL CONT
INTERFACE
COLOR
KILLER
ID DET
PB
APC
+
R121
C114
22uH
0305
2FSC
C4608
0.1 F
C152 0.1 B
0.47 B
C149
27K
100CT4R407
R
DET
18K 1/4W
5.5
0
COMPOUND
Q108
DTC143EKA
2
4.9
470P CH
0
0.7
4.7K
0.5
R111
4.7K 0.7
PB SW
Q106
KTC3198
7
0
0
PB SW
Q107
KTC3198
0
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
S.DET-H
4.9
3.9K
R110
PICTURE_CTL
560P B PB SW
Q105
KRA103SRTK
100uH
0305
4
1SS133
5
3
D101
100uH 0305
L103
0.022 B
R4603
1.8K 1/4W
FSC
C148
0.1 B
R118
C143
C146 50V 2.2
1K
R116
B
C141
81
82
83
SW39
2
REC
APC
MIX
LEVEL C.K
ADJ
FM
AGC
2.08
6
2
COIL,BIAS OSC
L104
1616004
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
B
+
L SECAM
629
TRAP
R120
C115
1
C113
0.0047 B
P.CON+5V
0
10K
C109
0.01 B
NORMAL AUDIO
REC ST SW
Q102
KTC3203_Y
10V 33 KA
0
C108
NA_REC-H
CP103
TMC-T02X-E1
2.2K
C106
W802
4.6
R101
SW38 EP1
16V 10 KA
100V 0.082 MMTV
4.9
OSC
Q104
KTC3203_Y
10V 220 YK
4.9
AUDIO PB
TO
FULL ERASE HEAD
H-15
47K
R107
C112
4.6
CH1
FROM
MESECAM
DET
R112
0.01 B
6
EP1
-
P.CON+5V
C116
C111
AUDIO REC
REC
MUTE
P SW7
SW37
8.2K
C117
C203
6.3V 47 KA
4
FH SYNC
P SW20
ACC
R
16V 10 KA 220
150
CTL+
CTL+
5
-
R114
100uH 0305
3
SW31
CH2
SW36 EP2
L108
C129
L102
L SECAM
SW27
B
3
KIL
SEP
HPF
COMP SW19
EP
VCA
EP2
+
1
C137
DOWN
CONV.
NORMAL_A_OUT
L110
P.CON+5V
R102
3.3
CTL-
B
V.REC_ST-H
R106
1
50V 0.47 KA
100uH
L4605
82K 1/4W
V.REC_ST_SW
Q103
DTC143EKA
0.9
CH1
SW35 SP1
HA VCC
C150
0
4.9
2.5
S_REC_IN/PB_OUT
CTL-
4
6
C4625
C4622
16V 10 KA
120P CH
39K
C4620
R4619
BUFFER
Q4606
KTC3875S_Y_RTK
0
R105
3
0
1
NA_REC-H
AE HEAD(+)
W860
A_MUTE/TRICK-H
L106
P.CON+5V
P.CON+5V
AE HEAD(-)
2
4.9
SP-H
0
CP102
IMSA-9604S-06Z14
1
B
100uH
0305
820P CH
FROM/TO HEAD AUDIO CONTROL
4
4.27
4.7
0.5
PB/REC REC
DISCRI AFC
2M LPF
R119
C101_1
2
4.9
C131 0.01 F
2.0
4.9
0.01 F 0
C122
1
0
0.1
0.022 B
SW28
SW29
SP
NORMAL_A_IN
100V
6
FE OSC COIL
C102
L101
1616002
0.01 F
1
3.3
0.01 B
KA
FE OSC
Q101
KTC3203_Y 4.7
0
0.01 F 0
C121
1K
8.2K
R103
EP_COM
EP-L
C134
EP-R
47K
R4626
EP/LP-CH2 (L)
0.01 F 4.9
0.01 F C135
1K
W871
1
EP-R
0.1 F
EP_COM
100P CH
R4622
SP SW
0
Q4604
KRC103SRTK
10V 33 KA
EP/LP_COM
C105
EP/LP-CH1 (R)
2
C103
3
0
SP-L
R104
SP-CH2 (L)
MMTV
SP_COM
4
L105
22uH 0305
C107
C4623
SP_COM
0.027
5
EP-L
R4615
5.0
VV SW
Q4603
KTC3875S_Y_RTK
HF2
SP-R
SP-CH1 (R)
P.CON+5V
W870
HF_COM
0.01 B
HF2 (L)
0.0047 B
HF_COM
7
10K
C104
8
15
3.05
MSECAM-M/AGC/S.DET
0
HF1
HF1 (R)
R4617
0
R4612
680P CH
C4613
C4604
10P CH
TOC-C09X-A1
9
6
FSC
R4609
FROM/TO CYL
27K
SECAM_H
10K
R4614
2FSC
CP101
14
2.36
F
C4616
0.01
L4603
TO SUB MICON/OSD/VPS
EE/VV_V_OUT
13
4.3
2
7
C204
1
C190
+
C140
12
2.31
R146
0
4PHASE GEN
SP1 SW30
CH2
SW34
91
11
2.19
2.2
4.86
2.2K
CR DET 2FSC
1/2
2FL VCO
-
92
10
2.38
C127 0.01 F C133
1K 1/4W
DET
+ SP2
SW33
93
9
2.62
2.2
0.01 F 2.2
COMP DET
SW32 SP2
270K
8
0
C124
C132
C128
C4615
3.3K
220P CH
R4608
2.7K
C4606
0.022 B
C4610
C4605
FRONT_V_IN
22K
R4602
FROM OPERATION/DISPLAY
50V 1 KA
D4601
GND
1SS133
R4606
P.CON+5V
7
0
0.001 B
6
2.77
C4624
5
0
SP_COM
AGC
DET
SP-R
1K
4
0
IREF
R4620
3
0
27uH
2
1.87
50V 0.47
KA
1
2.4
REC
AGC
AMP
REG
4.3V
REC ON
C126
B
PB
2.2
94
HF1
1.1MHz
OSC
C123 0.01 F
SP-L
ENV HPF
DET
HA GND
97
REC
MUTE
KA
VA
6.3V 47
CA
B
0
2.8
180P CH
2FSCVCO
ME
SECAM
DET
AMP
Q111
KTC3875S_Y_RTK
2.07
R131
C159
KILLER
DET OUT
SW1EP ON
C120 0.1 F
5P CH
C GND DO
X TAL VCO/OSD
0.22uH
ENV.DET
PB
4.43MHz
VCO
HF2
2.4
84
1.1MHz
BPF
C130
50V 3.3 KA 0.9
85
1
4
SYNC
GATE
C158
HEAD SW1
HEAD SW2 TANC
LIMITTER
86
0.033 B
NORMAL_A_IN
FROM REGULATOR
1.1
87
PB
REC
Fo
ADJ
HF_COM
C125
5
88
X2
LIM
89
4.3MHz
BPF-B
Filter Adj
AFC
NORMAL_A_OUT
V.H_SW
REC
2.2MHz
BPF
X2
90
CONTROL
LOGIC
NC
95
4.3MHz
BPF-A
to MUTE
FROM/TO HI-FI/DEMODULATOR
SYNC
GATE
3
8
NC
0 2.1 2.8 4.7 2.1 2.1 1.7 1.7 1.9 2.1 2.5 2.8 1.4 5.0 5.0 5.0 2.2 4.2 3.2 3.0 5.0 2.1 0.1 3.3 2.8 2.1 2.0 2.8 2.7 0
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
96
VA
Y/C/AUDIO/CCD
/HEAD AMP IC
IC101
HA118217F
2.6
98
CA
0.001 B
H.SW
TP101
100 99
PB
MUTE
0.01 F
MODE
CTL
PB
C118
to PB AGC
to REC KILLER
L107
REC
Fo
ADJ
47P CH
TU_V_OUT
LA7358M
SWD_VIDEO
FRONT_V_IN
BGP
GEN
IC4601
SECAM_CHOMA_IC
FROM TUNER/JACK
C119
to MUTE
to SYNC GATE
SYNC GATE GEN
/ V-SEP
S.DET-H
6
REC
/PB
B
4.43MHz
OSC
0.001 B
SP-H
PB ON
IREF
SECAM
DET
SECAM_H
X101
16
Vcc
SECAM_IN
4
C138
2.68
17
C147
0
18
1
2.4
19
SW40
SP ON
680
0.1 F
R4621
2.11
20
50V 4.7 KA
2.22
21
0.0022 B
2.4
22
0.01 F
2.7
23
C139
4.87
24
27K
C4619
R4618
4.82
25
4
W886
C136
2.97
26
47K
R4616
C4614
1.92
27
W885
0.01 B R113
4.4
28
VV-H
REC_IN
6.3V 47 KA
4.5
29
0.0022 B
50V 2.2 KA
C4612
2.2K
4.5
30
MSECAM-M/AGC/S.DET
5
3.3K
0.01 B
V.ENV
TP102
NC
3.2
0.0022 B
CTLV.REC_ST-H
C4609
CTL+
R4605
C4602
ENV.DET
220P CH
IIC_CLK
18K
R4604
A_MUTE/TRICK-H
IIC_DATA
2
R4601
C4626
0
SYNC
7
3
S_REC_IN/PB_OUT
R4623
10K 1/4W
2.0
BUFFER
Q4601
KTC3875S_Y_RTK
2.0
4.8
1.0
1.8K
10K
0.01 B
R4625
5.0
SECAM PB
SW
Q4605
KTC3875S_Y_RTK
2.9
15K
R4611 0
C4621
R4624
8.2K
0
C4617 L4604
150P CH
R4610
0.01 B C4611
2.2K
C4607
R4607
VV SW
Q4602
KTA1504S_Y_
RTK
75P CH 68uH
DUMMY_V.SYNC
0.1 F
6.3V
NA_REC-H
C4603
C4601
V.H_SW
PICTURE_CTL
47 KA
VV-H
L4602
FROM/TO VCR SYSCON
6.8uH
SYNC
47uH
0305
SECAM_IN
P.CON+5V
(SD-22VE)
L4601
0.1 F
8
PCB010
VMB252
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
F
G
H
H-16
1
FE HEAD(GND)
2
FE HEAD(HOT)
R148
1.8K
C205_1
F
0.01
1
SINGLE SW IC
IC102
TC7SB384FU
C201_1
W882
W881
W852
F
B
0.1
C173
F
0.01 B
C170
0.1
C177
B
0.1
C169
KA
50V 4.7
B
C165
4.7K
0.001
12uH
R125
2
19
P
20
21
91P
24
25
26
C174
C175 50V 3.3 KA
B
0.1
F
1
C172
F
27
0
4.7K
5.15
0
2.6
C183
4.9
0.01 F
2.0
4.9
4.9
29
F
0.01
6.3V
0.1
C194
C193
4.9
47 KA
5
3.0
L116
4.9
0
0
16V 10 KA
0
2.8
30
2.8 1.9 2.8
P.CON+5V
100uH 0305
3.0
SWD_VIDEO
AGC
28
0.01 F
C186
34
0
1.9
C181
1
4
FRONT_V_IN
B
C191
50V
0
0
6
C187
50
49
48
47
46
39
38
37
YGND
23
CH
COMPOUND 0
Q110
DTC143EKA
0
220uH
47P CH
C171
5.6K
R126
C164
45
44
43
42
R
22
R132
C188
L111
ATT
(-10dB)
LPF
0.1
C168
0.1 F
R127
ATT
(-10dB)
SYNC
0
C184
18
ATT
(-10dB)
SW15 CLAMP
CLAMP
C166
0.1 B
6.8K
C162
41
40
SW12
CH1
CH2
10 1/4W
0
16V 10 KA
17
R
33
P
R
32
P
SW115
VIDEO AGC
CH3
SW14
YNR
REC
DO
DO
31
SW10
2.2M 1/4W
150P CH
VCC=5V
35
REC
AGC DEL
PB ALC
36
R
D.E.
N.C.
MODE
CONT CCD
R145
0.3
1
TU_V_OUT
KA
5.12
COMPOUND
Q113
DTC143EKA
50V 2.2 KA
16
P SW17
C179
15
Y
CCD
FBC/ALC
Y LPF
SW9 R P
1.5K
R122
CCD
GND
5
47P CH
14
4
3
KA
0.1 F
C161
820
C157
0
0
5.5
COMPOUND
Q108
DTC143EKA
7
2
PB SW
Q107
KTC3198
0
S.DET-H
4.7K 0.7
PB SW
Q106
KTC3198
0
0
B.D
P
PICTURE_CTL
R111
SW16
R
NL NL
EMPH DE EMPH
MAIN
DE EMPH
6.3V
0.018 B
470P CH
0.5
C156
R123
16V 10 KA
C153
C155
22K
R121
R119
C145
3.9K
4.7K
3
C190
180P CH
7
0305
4.9
SQUELCH
FEED BACK
CLAMP
VIDEO ALC
Y APA
DO EDGE
DET DELAY
SW11
13
100uH
4.9
R109
0
KA
10K
C151
0.7
LMIT
WHAITH
N P
C
CCD
SUB LPF
MAIN
EMPH
CARRIER
OFFSET
W.C/DC
R117
C144
CLEAR SYNC
SW18
TRAP
P
DLIM
0.1 F
C150
COIL,BIAS OSC
L104
1616004
47 KA
6.3V
L112
50V 4.7 KA
C154
SW3
REC ON
R115
2.2K
R110
C.K
CLPH
CLPH
SW24
R
MAIN
CONV2
MAIN +
CONV1 SW22
P
SW23
R
R
P
P SW21
R
BPF
P
2.8 2.5 2.6 2.5 2.4 2.4 4.9 1.2 1.2 3.0 0.6 0.6 2.2 3.1 2.7 2.4 2.0 3.1 2.1 1.5 2.1
NC NC
NORMAL_A_OUT
L110
P.CON+5V
4
1SS133
3
C163
C167
B
0.1
27K
C152
0.022 B
12
6.3V 22 KA
C142 0.22uH
B
C136
11
47
PCB010
VMB252
CAUTION: DIGITAL TRANSISTOR
A
0
10
9
W869
2.5
FO/DEV
ADJ
S-DET
YVCC
1
8
DELAY
47
82
83
84
0
3 2
7
470P CH
560P B PB SW
Q105
KRA103SRTK
CAUTION: DIGITAL TRANSISTOR
1
H-17
C149
B
C128
47P CH
47K
C114
5
D101
L103
100uH 0305
C113
0.0047 B
P.CON+5V
0
C109
0.01 B
NORMAL AUDIO
REC ST SW
Q102
KTC3203_Y
C108
NA_REC-H
CP103
TMC-T02X-E1
C106
W802
TO FULL ERASE HEAD
2.2K
0
10V 33 KA
10K
4.6
R101
6
2
NA_REC-H
R106
1
P.CON+5V
4.9
R107
C112
820P CH
4.9
6
CTL+
MMTV
AUDIO PB
4.6
CTL-
FM MOD
R120
100V 0.082
AUDIO REC
6
2.5
16V 10 KA
C115
5
2.5
6
5
APC
SW
DEMO
SW6
R112
10V 220 YK
CTL+
4
18K 1/4W
C116
C111
CTL-
4
3.3
3
R105
2
AE HEAD(+)
3
8.2K
C117
PULSE
GEN
G
EQ
SQPB
LAG LERD
LPF
P.CON+5V
150
+
7M HPF
VCA
BAND
A.GND GAP
100uH 0305
OSC
Q104
KTC3203_Y
PRE
AMP
B.E
1M HPF
P SW2
R
6.3V
C110
SYNC.SEP.
CLOCK
DEIVER
S SQPB
DL
P
EQ
DET
NORMAL_A_IN
R102
3
FM
AGC
B
C203
47P CH
6dB AMP
C SQUELCH
R
16V 10 KA 220
0
L102
LPF
6dB AMP
LEVEL DET2
R
CTL TRAP
HPF
FHTRAP
+
629
TRAP
R
REC EQ
R114
C137
V.REC_ST-H
0
0.47 B
KA
4.7
CP102
IMSA-9604S-06Z14
AE HEAD(-)
6.3V 47 KA
KA
C103
V.REC_ST_SW
Q103
DTC143EKA
0.01 B
C101
FROM/TO HEAD AUDIO CONTROL
10V 33
4.9
2
4
4.9
0.0047 B
6
4.7
10K
C104
100V 0.027 MKT
FE OSC COIL
C102
L101
1616002
0.01 F
1
3.3
0.01 B
C105
R103
FE OSC
Q101
KTC3203_Y
EP-L
3
MUTE
L109
EP/LP-CH2 (L)
EP-R
EP_COM
L SECAM
SW4 SW5
AVCC
2
-
SW26R
SW25
DL
ACC
DET
1/2
PHASE SW
MIX
LEVEL C.K
ADJ
+
0.22uH
1
SW39
L108
EP/LP_COM
CH1
FROM
MESECAM
DET
+
C140
EP/LP-CH1 (R)
2
EP1
SW38 EP1
L107
3
SP-L
REC
MUTE
P SW7
SW37
270K
SP-CH2 (L)
0.01 F
4
0.01 B R113
C129
SP_COM
-
DET
HF2
SP_COM
SW31
CH2
SW36 EP2
1
SP-R
5
2
2.5
HF_COM
SP-CH1 (R)
1
0.9
B
100uH 0305
HF1
R104
6
1
A_MUTE/TRICK-H
L106
P.CON+5V
CP101
TOC-C09X-A1
HF2 (L)
0
4.9
C107
FROM/TO CYL
HF_COM
4.9
W860
MSECAM-M/AGC/S.DET
EE/VV_V_OUT
EP2
+
L SECAM
SW27
16V 10 KA
TO SUB MICON/OSD/VPS
7
0.5
1 B
2FSC
100CT4R407
B
C131 0.01 F
FRONT_V_IN
P
COLOR
KILLER
ID DET
PB
APC
SEP
HPF
COMP SW19
EP
C147
EP-R
0
0.01 F 0
C122
REC
APC
P SW20
ACC
R
2M LPF
VCA
SW40
SP ON
0.01 F C135
FROM OPERATION/DISPLAY
SW28
SW29
SP
CH1
SW35 SP1
HA VCC
KA
0.01 F 0
C121
EP_COM
0
DOWN
CONV.
+
50V 4.7
GND
C134
SP1 SW30
CH2
SW1EP ON
EP-L
0.01 F 4.9
0.1 F
4PHASE GEN
0.0022
P.CON+5V
L105
22uH 0305
1/2
2FL VCO
-
SW34
91
P.CON+5V
2.2
92
FROM REGULATOR
C127 0.01 F C133
93
SP-R
PB/REC REC
DISCRI AFC
+ SP2
SW33
94
HF_COM
2.2
0.01 F 2.2
C132
6.3V 47
C126
HF2
C124
FH SYNC
N-P CONT
OUT
CCD
LPF
LEVEL DET1
DET
SW32 SP2
97
SP_COM
2.2
ME
SECAM
DET
VCA
SERIAL CONT
INTERFACE
CR DET 2FSC
2FSCVCO
COMP DET
0.22uH
KA
HF1
1
81
C123 0.01 F
SP-L
85
NORMAL_A_IN
86
0
ENV HPF
DET
HA GND
87
C120 0.1 F
NORMAL_A_OUT
0.1
C159
KILLER
DET OUT
88
2.4
50V 3.3 KA 0.9
ENV.DET
FROM/TO HI-FI/DEMODULATOR
C130
89
B
90
0.033
X TAL VCO/OSD
2.2K
C204
0.022 B
HEAD SW1
HEAD SW2 TANC
LIMITTER
95
5
TU_V_OUT
1.1
96
C125
98
FRONT_V_IN
100 99
C118
V.H_SW
5P
CH
2
R146
100uH 0305
1
0.001 B
Y/C/AUDIO/HEAD AMP IC
NC
IC101
0 2.1 2.8 4.7 2.1 2.1 1.7 1.7 1.9 2.1 2.5 2.8 1.4 5.0 5.0 5.0 2.2 4.2 3.2 3.0 5.0 2.1 0.1 3.3 2.8 2.1 2.0 2.8 2.7 0
NC
HA118217F
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51
TP101
2.6
C GND DO
CVCC
KIL
NTSC/PAL
H.SW
0.001 B
SWD_VIDEO
X101
C119
FROM TUNER/JACK
8
R118 0.1
R116
F
C139
C141
S.DET-H
HF1 (R)
C158
0.01
V.ENV
NC
TP102
V.REC_ST-H
MSECAM-M/AGC/S.DET
9
C146
4
W886
CTL+
1K
ENV.DET
C148
C143
W885
CTL-
4
50V 2.2
IIC_DATA
5
2.07
L124
A_MUTE/TRICK-H
6
1K
R144
P.CON+5V
EE/VV_V_OUT
IIC_CLK
100
2.8
4.86
SYNC
7
8
AMP
Q111
2SC2412K
DUMMY_V.SYNC
IIC_CLK
0.01
NA_REC-H
3
H
100
(VCR PCB)
(SD-22VL)
V.H_SW
PICTURE_CTL
R134
FROM/TO SYSCON2
2FSC
Y/C/AUDIO/HEAD AMP
SCHEMATIC DIAGRAM
G
DUMMY_V.SYNC
F
IIC_DATA
E
R135
D
P.CON+5V
C
L113
8
B
22uH 0305
A
B
C
D
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
E
RECORD COLOR SIGNAL
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
F
1
RECORD LUMINANCE SIGNAL
G
H
H-18
A
B
C
D
E
F
G
H
VCR SYSCON SCHEMATIC DIAGRAM
(VCR PCB)
FROM/TO REGULATOR
(SD-22VB)
W810 MSECAM-M/AGC/S.DET
MSSW_B
KEY-A
MSSW_A
KEY-B
EOT
AFT_S.CURVE
ENV.DET
HIFI_ENV.DET
BOT
CAP_F/R
1K
R3022
R3024
7
18K
R3021
R3019
CAP_VCO
AT+12.6V
27K
AT+5V[M-CON]
CAP_LIMIT
REM_IN
S.DET-H
V.H_SW
DVD_RESET
HIFI_H.SW
CENT_LED
POWER_FAIL
FROM/TO TUNER/JACK
IIC_CLK
IIC_DATA
AFT_S.CURVE
1K 1/4W
VCR_POWER_ON-H
VCR_POWER_ON-H
DVD_POWER_A
A_MUTE/TRICK-H
AT+5.2V
P.CON+5V
FL_CS
MOTOR_GND
NA_REC-H
DUMMY_V.SYNC
(S/S)
CAP_ON
8
GND
DVD_MUTE
8
FROM/TO SUB MICON/OSD/VPS
7
SUB_CS
SUB_CLK
R3015
SUB_DATA_IN
C3033
SUB_DATA_OUT
27K
6.3V
C3002
R3035
R3032
100
F
2.6 50V 4.7
560
PICTURE_CTL
NA_REC-H
DUMMY_V.SYNC
C3032
KA
A_MUTE/TRICK-H
6.3V
0
FROM/TO Y/C/AUDIO/HEAD AMP
V.H_SW
R3041
C3020
2.6
FF/REW SW
Q3009
KRC103SRTK
0.001 B
560
0
10K
0
0.1
6
C3037
R3038
GND
5.1
R3043
IIC_DATA
47 KA
IIC_CLK
1.3
5
ENV.DET
0
R3039
2.2
10K
C3036
MSECAM-M/AGC/S.DET
CTL+
0.0022 B
CTL-
0.3
SYNC
R3054
0
10K
S.DET-H
1K 1/4W
98
95
94
93
92
91
90
89
88
85
84
0
NC
C3018
1K 1/4W
R3045
FROM/TO OPERATION/DISPLAY
4
CG_CLK
CG_DATA
FL_CS
0.1
22K
B
C3025
KEY-A
KEY-B
0.0068 B
REM_IN
C3026
SEG_10
CYL_FG/PG
CAP_FG
POWER_FAIL
50V 1 KA
PICTURE_CTL
C3015
100
0.0033 B
HIFI_REC_MUTE
R3029
C3031
CLOCK
TP3002
5.6K
1/4W
IIC_DATA
IIC_CLK
CG_CLK
1K
R3026
CG_CS
CG_DATA
SUB_CLK
SEG_10
SUB_DATA_IN
SUB_DATA_OUT
270 1/4W
CENT_LED
16V 10 KA
CG_DATA
5.1
0
0
C3019
80
4.9
R3034
R3031
0.1
79
F
TAB_SW
R3028
1K
R3025
78
F
R3044
77
0
150P CH
76
C3034
0 16V 10 KA
2.6
CG_CLK
FF/REW SW
Q3008
KRC103SRTK
C3030
C3023
75
0 0.5 2.6 2.5 4.9
NC
1K
D3001
LNA2702L010R
97
74
0
3.3K
R3004
220K
R3003
SW3001
LSA-1144EAU
330K
R3001
TAB SW
96
73
0
R3030
5.1
87
86
72
0
0.1
0
0.0039 B C3027
71
F
2.6
22K
70
2.5
C3021
C3029 0.1
0.0039 B
CAP_ON
69
0 1.3 1.2
0.1
R3037
68
5.1
4.7K
67
C3024
CAP_CTL
66
83
65
CG_CS
5.1
82
64
IIC_DATA
B
81
63
R3036
62
REEL-T
61
CYL_CTL
60
4.1 4.1 4.1 4.1 4.1 5.1 5.1 5.1 5.0
NC NC NC NC NC
0.01
5.1
TAB_SW
33K
59
0
5.2
P.FAIL
REEL-S
58
HIFI REC MUTE
57
32KHz MONITER
56
IIC-SDA
55
47K 1/4W
CENT SW
Q3003
KRC103SRTK 0
99 100
KEY-B
EOT
AFT SC
A.ENV
V.ENV
PERI_CTL/AGC
BOT
CAP_FWD
CAP_LIMIT
D.V SYNC
REMOCON
S.DET-H
SECAM_IN
DVD_RESET
VH SW
AH SW
POWER ON-H A
A.MUTE
CENT LED
SECAM_H
SP-H
54
CAP CTL
53
PICTURE_CTL
52
C SYNC
V.REC ST-H
51
1.0 2.0 3.0 3.0 4.0
0 2.0 5.0 3.0
NC NC NC NC NC NC NC NC
TAB_SW
IIC-CLK
SEG 1
NC
CG-CLK
SUB_RESET
R3005
4
LDM CTL
ZERO MUTE
CFG
80 REEL-T
CG_CS
0
NC
SERVICE 1
TP3001
BOT
SEG 4
CG-DATA
EOT
53
79 REEL-S
SUB_CLK
0
SEG 3
SUB DATA IN
SUB_RESET
52
DFG
78 CYL CTL
SUB DATA OUT
0
NC
5.1
SEG 2
GRID5
0
EOT SENSOR
Q3002
ST-304L
51
GRID4
BOT SENSOR
Q3001
ST-304L
5.1
2.5
SERVICE2
SUB_CS
47
5.1
FF/REW-L
32
33
34
35
36
44
4.5
45
10K
SUB_CS
CTL -
SERVICE1
46
5.1
48
R3013
CTL +
RESET
5.1
10K
KEY-A
AMP VSS
GRID3
R3007
5
37
5.1
GRID2
100
3
CTL VSS
AMP V.OUT
SEG 10
RESET
XC OUT
1.2
GRID1
18P CH
R3008
SEG 9
C3007
MSSW_A
AMP V.IN
SEG 8
CYL_CTL
XC IN
SEG 7
CYL_CTL
49
12
CYL_FG/PG
VSS
1.1
MSSW_B
2
SYSCON/SOFTWARE/SERVO IC
IC3001
OEC7078C
X OUT
50
11
CYL_FG/PG
1
CTL AMP OUT
100 MSECAM-M/AGC /
CTL SW OUT
MSECAM-M/S.DET
SEG 6
LDM_CTL
0
A VCC
CTL AMP IN
X IN
2.4
C3035
AMP C
30 VV-H
SEG 5
10
18P CH
CAP_CTL
VCC
2.4
C3010
W807
CLKSEL
NA_REC-H
SUB_RESET
47 KA
IIC_CLK
0 4.3 5.1 5.1 4.8 4.8
5
4
3
2
1
6
AMP VCC
28 DVD_MUTE
29
5.1
38
CAP_CTL
NC
39
9
NC
40
LD/CY_VCO
470
DVD_POWER_C
41
8
R3009
18P CH
NC/PERI_CTL-L
43
GND
C3009
0.1 F
7
3.3K 1/4W CAP_LIMIT
C3038
0.1 F
0
5.1
C3011
GND[M]
1M
I_LIMIT
6
CAP_F/R
R3011
5
R3006
10M
CAP/M/F/R
X3002
VCC
4
100CT01207
3
18P CH
R3010
CAP_VCO
CAP_FG
X3001
2
C3008
100DA32R01
6
CAP_FG
0
NC
0
NC
0
DVD_POWER_A
42
CP3001
TMC-J12P-B2
31
DVD_POWER_A
FROM/TO DECK
1
5.0
FL_CS
35V 330 YK
CAP_ON
NC
NC NC
NC
0 3.5
0 0 2.6 5.1
0
0
5.1
0
0 5.1 5.1 2.6 2.6 5.1 0
0
0
0 0.9 4.2
0 5.1
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
3
3
RESET
REEL-T
MS_SEN A
Q3005
RPI-352C40N
NC
33K
100
R3016
R3014
33K
MSSW_B
R3012
PST3231NR
IIC_CLK
IIC_DATA
IN
GND
2
3
0
1
5.1
TO DVD IN/OUT
DVD_RESET
2
DVD_MUTE
17
3
4.9
4
0
R3033
3
5
6
7
8
SDA
SCL
TEST
VCC
VSS
A2
A1
A0
4
4.9
0
4
18
0
3
0
2
0
1
0
47K
D3002
5.1
0
R3040
1.3
F
1.3
18K 1/4W
0
1
1SS133
MSSW_A
2
C3028
4
4.8
1.2
1
0.047F
2.6
HIFI_H.SW
5.5V
1
4
4.8
1.2
2
C3022
1
REEL SENSOR
Q3006 RPI-303
2.4
3.8
HIFI_ENV.DET
NC
W887
3
C3016
2
3
0
4.9
0.47
2
3.8
EEP ROM IC
IC3099
S-24C08ADPA-01
4.9
4.9
4
OUT
5.1
REEL SENSOR
Q3007 RPI-303
2
HIFI_REC_MUTE
NC
0
NC
PCB010
VMA252
16V 10 KA
MS_SEN B
Q3004
RPI-352C40N
5
IC3004
SYSTEM RESET IC
NC
W809
REEL-S
IIC_CLK
W808 IIC_DATA
R3020
47K 1/4W
R3018
120 1/4W
47K 1/4W
R3017
FROM/TO HI-FI/DEMODULATOR
CAUTION: DIGITAL TRANSISTOR
1
1
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A
H-19
B
C
D
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
F
G
H
H-20
A
B
C
D
E
F
G
H
VCR SYSCON SCHEMATIC DIAGRAM
(VCR PCB)
FROM/TO REGULATOR
(SD-22VE)
W810 MSECAM-M/AGC/S.DET
MSSW_B
KEY-A
MSSW_A
KEY-B
EOT
AFT_S.CURVE
ENV.DET
HIFI_ENV.DET
BOT
PERI_CTL-L
CAP_F/R
CAP_LIMIT
REM_IN
S.DET-H
SECAM_IN
V.H_SW
DVD_RESET
HIFI_H.SW
CENT_LED
VCR_POWER_ON-H
SP-H
VCR_POWER_ON-H
A_MUTE/TRICK-H
DVD_POWER_A
SECAM_H
P.CON+5V
FL_CS
AT+5.2V
CAP_ON
MOTOR_GND
VV-H
DUMMY_V.SYNC
(S/S)
DVD_MUTE
8
GND
NA_REC-H
8
POWER_FAIL
AT+5V[M-CON]
IIC_CLK
IIC_DATA
AFT_S.CURVE
W875
R3024
PERI_CTL-L
FROM/TO SUB MICON/OSD/VPS
SUB_CS
1K
18K
R3021
27K
R3019
7
1/4W
CAP_VCO
AT+12.6V
FROM/TO TUNER/JACK
6.3V
73
74
75
76
77
0 0.5 2.6 2.5 4.9
R3035
R3032
100
NA_REC-H
0.001 B
560
10K
C3020
PICTURE_CTL
C3037
94
93
92
91
89
88
85
84
R3041
V.H_SW
DUMMY_V.SYNC
A_MUTE/TRICK-H
C3032
2.6 50V 4.7 KA
IIC_DATA
IIC_CLK
6.3V 47 KA
0
ENV.DET
1.3
R3039
C3036
10K
0.0022 B
2.2
MSECAM-M/AGC/S.DET
CTL+
CTL-
0.3
SYNC
R3054
0
10K
82
81
SECAM_IN
SECAM_H
SP-H
S.DET-H
FROM/TO OPERATION/DISPLAY
CG_CLK
C3025
0.0068 B
R3037
0.1 B
KEY-A
KEY-B
REM_IN
C3026
SEG_10
FROM/TO HI-FI/DEMODULATOR
CYL_FG/PG
CAP_FG
POWER_FAIL
TAB_SW
CAP_ON
50V 1 KA
C3015
4
CG_DATA
FL_CS
R3034
PICTURE_CTL
5
V.REC_ST-H
0
0.0033 B
V.REC_ST-H
100
560
NC
22K
HIFI_REC_MUTE
R3029
IIC_DATA
0
C3018
5.6K
1/4W
1K
IIC_CLK
0
VV-H
FF/REW SW
Q3009
KRC103SRTK
0.1 F
CLOCK
TP3002
4.9
R3036
R3028
1K
R3025
R3026
CG_CLK
CG_CS
CG_DATA
SUB_CLK
SUB_DATA_OUT
SEG_10
CENT_LED
SUB_DATA_IN
0.1
0
R3043
98
95
97
0
1/4W
270 1/4W
R3004
96
0
R3030
5.1
C3031
R3038
CAP_CTL 4.7K
0
16V 10 KA
0 16V 10 KA
2.6
6
0
0
FROM/TO Y/C/AUDIO/HEAD AMP
C3019
2.6
80
REEL-T
0 1.3 1.2
79
CYL_CTL
4.1 4.1 4.1 4.1 4.1 5.1 5.1 5.1 5.0
NC NC NC NC NC
78
F
C3030
2.6
GND
1/4W
72
F
CG_DATA
1K
71
0.1
0
0.1
CG_CLK
1K 1/4W
70
C3021
C3029
0.0039 B
2.5
R3045
69
C3034
R3044
68
F
CG_CS
FF/REW SW
Q3008
KRC103SRTK
5.1
0
CH
67
0.1
IIC_DATA
B
150P
66
5.1
C3023
65
C3024
0.0039 B C3027
64
5.1
22K
63
0.01
5.1
TAB_SW
R3031
5.1
87
86
62
83
CAP CTL
61
3.3K
CENT SW
Q3003
KRC103SRTK 0
99 100
KEY-B
EOT
AFT SC
60
0
5.2
P.FAIL
1K
D3001
LNA2702L010R
R3003
220K
LSA-1144EAU
R3001
330K
TAB SW
SW3001
47K
A.ENV
59
10K
4
V.ENV
PERI_CTL/AGC
BOT
CAP_FWD
CAP_LIMIT
REMOCON
D.V SYNC
SECAM_IN
S.DET-H
VH SW
DVD_RESET
AH SW
POWER ON-H A
A.MUTE
PICTURE_CTL
58
V.REC ST-H
57
HIFI REC MUTE
56
32KHz MONITER
55
IIC-SDA
53
IIC-CLK
52
1.0 2.0 3.0 3.0 4.0
0 2.0 5.0 3.0
NC NC NC NC NC NC NC
NC
R3055
R3005
CENT LED
SP-H
54
SEG 1
CG-CLK
SUB_RESET
C SYNC
33K
45
ZERO MUTE
CFG
80 REEL-T
LDM CTL
51
TAB_SW
79 REEL-S
CG_CS
BOT
SEG 4
CG-DATA
NC
SERVICE 1
TP3001
NC
0
SEG 3
SUB_CLK
EOT
52
53
DFG
78 CYL CTL
SUB DATA IN
5.1
SUB_RESET
SEG 2
SUB DATA OUT
0
0
46
47
2.5
EOT SENSOR
Q3002
ST-304L
SUB_CS
51
REEL-S
44
0
4.5
SERVICE2
48
5.1
AMP VSS
49
BOT SENSOR
Q3001
ST-304L
AMP V.OUT
SERVICE1
50
5.1
AMP V.IN
5.1
10K
SUB_CS
90
RESET
5.1
R3013
SECAM_H
32
33
34
35
36
XC OUT
5.1
10K
FF/REW-L
31
100
R3007
5
XC IN
GRID5
RESET
VSS
1.2
CTL VSS
CTL -
GRID4
18P CH
37
1M
R3011
R3008
CTL AMP OUT
CTL +
GRID3
CYL_CTL
C3007
KEY-A
GRID2
CYL_CTL
3
GRID1
CYL_FG/PG
MSSW_A
SYSCON/SOFTWARE/SERVO IC
IC3001
OEC7079D
X OUT
1.1
MSSW_B
2
SEG 10
CYL_FG/PG
A VCC
100 MSECAM-M/AGC /
CTL SW OUT
MSECAM-M/S.DET
SEG 9
LDM_CTL
0
IIC_CLK
CTL AMP IN
SEG 8
W807
2.4
39
CAP_CTL
X IN
2.4
1
SUB_RESET
C3035
AMP C
30 VV-H
SEG 7
12
18P CH
CAP_CTL
VCC
5.1
C3010
LD/CY_VCO
CLKSEL
NA_REC-H
SUB_DATA_OUT
47 KA
0 4.3 5.1 5.1 4.8 4.8
5
4
3
2
1
6
AMP VCC
28 DVD_MUTE
29
SEG 6
11
0.1 F
NC
SEG 5
10
470
NC
40
9
R3009
18P CH
DVD_POWER_C
41
GND
8
C3009
NC/PERI_CTL-L
42
7
3.3K 1/4W CAP_LIMIT
C3038
DVD_POWER_A
43
GND[M]
5.1
0.1 F
I_LIMIT
6
0
C3011
5
CAP_F/R
10M
CAP/M/F/R
R3006
X3002
VCC
4
100CT01207
CAP_VCO
3
R3010
2
18P CH
X3001
CAP_FG
C3008
CAP_FG
100DA32R01
6
1
0
NC
0
NC
0
38
FROM/TO DECK
FL_CS
5.0
DVD_POWER_A
CAP_ON
5.1
0
0 5.1 5.1 2.6 2.6 5.1 0
0
0
0 0.9 4.2
0 3.5
0 0 2.6 5.1
0
0
0 5.1
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
35V 330 YK
TMC-J12P-B2
SUB_DATA_IN
C3033
27K
C3002
CP3001
7
SUB_CLK
R3015
HIFI_REC_MUTE
HIFI_ENV.DET
HIFI_H.SW
3
3
IIC_CLK
RESET
MS_SEN A
Q3005
RPI-352C40N
NC
IN
GND
2
3
0
1
5.1
2
3
VCC
4.9
VSS
A2
A1
A0
0
4
18
0
3
0
2
0
1
0
1SS133
TEST
4
47K
D3002
SCL
R3040
SDA
18K 1/4W
8
F
5.1
0
7
5.5V 0.047F
4
4.9 0
1.3
6
C3028
17
3
1.3
5
PCB010
VMB252
16V 10 KA
33K
100
R3016
R3014
OUT
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
H-21
33K
R3012
MSSW_B
1
DVD_MUTE
R3033
0
1
C3022
4.8
MSSW_A
2
0.47
2.6
4
1.2
1
C3016
3.8
1
4
4.8
1.2
2
IC3099
S-24C08ADPA-01
2.4
1
TO DVD IN/OUT
0
W887
3
EEP ROM IC
2
3
4
4.9
REEL SENSOR
Q3007 RPI-303
2
3.8
REEL SENSOR
Q3006 RPI-303
MS_SEN B Q3004
RPI-352C40N
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
4.9
0
DVD_RESET
5.1
2
4.9
PST3231NR
SYSTEM RESET IC
REEL-T
5
IC3004
W809
REEL-S
IIC_CLK
W808 IIC_DATA
R3020
47K 1/4W
R3018
120 1/4W
CAUTION: DIGITAL TRANSISTOR
47K 1/4W
R3017
IIC_DATA
NC
NC
B
C
D
E
F
G
H
H-22
A
B
C
D
E
F
G
H
VCR SYSCON SCHEMATIC DIAGRAM
(VCR PCB)
FROM/TO REGULATOR
(SD-22VL)
MSSW_B
KEY-A
MSSW_A
KEY-B
EOT
AFT_S.CURVE
ENV.DET
HIFI_ENV.DET
BOT
PERI_CTL-L
1K
AT+5V[M-CON]
27K
R3015
1/4W
R3024
IIC_CLK
AFT_S.CURVE
FROM/TO SUB MICON/OSD/VPS
SUB_CLK
SUB_DATA_IN
C3033
6.3V
C3002
R3035
R3030
R3032
100
B
10K
C3037
NA_REC-H
0.001
PICTURE_CTL
R3043
6.3V
0
V.H_SW
DUMMY_V.SYNC
A_MUTE/TRICK-H
IIC_DATA
IIC_CLK
47 KA
ENV.DET
1.3
0
C3036
10K
2.2
MSECAM-M/AGC/S.DET
CTL+
0.0022 B
CTL-
0.3
SYNC
10K
CH
C3018
R3045
150P
S.DET-H
1K 1/4W
R3054
0
5
V.REC_ST-H
R3039
1K1/4W
94
93
92
91
90
89
88
85
84
F
C3032
2.6 50V 4.7 KA
FROM/TO Y/C/AUDIO/HEAD AMP
FF/REW SW
Q3009
KRC103SRTK
FROM/TO OPERATION/DISPLAY
4
CG_CLK
CG_DATA
FL_CS
0.1 B
R3034
C3025
0.0068
KEY-A
KEY-B
B
REM_IN
C3026
SEG_10
CYL_FG/PG
CAP_FG
FROM/TO HI-FI/DEMODULATOR
POWER_FAIL
C3015
50V 1 KA
PICTURE_CTL
0.0033 B
V.REC_ST-H
100
0.1
C3020
CLOCK
NC
TP3002
22K
HIFI_REC_MUTE
R3029
IIC_DATA
IIC_CLK
CG_CLK
2.6
80
4.9
5.6K
1/4W
1K
R3026
CG_CS
CG_DATA
0
SUB_CLK
SEG_10
CENT_LED
SUB_DATA_IN
SUB_DATA_OUT
270 1/4W
0.1
79
0
C3031
TAB_SW
R3028
1K
R3025
78
5.1
R3041 560
0
C3023
77
6
0
16V 10 KA
0 R3038 560
GND
5.1
R3044
98
95
97
76
1K
D3001
LNA2702L010R
96
75
0 0.5 2.6 2.5 4.9
R3031
CENT SW
Q3003
KRC103SRTK
87
86
74
0
3.3K
5.1
99 100
KEY-B
EOT
AFT SC
73
0
47K 1/4W
R3004
220K
R3003
SW3001
MXS01350MVP0
R3001
330K
A.ENV
72
0
C3019
0 16V 10 KA
CG_DATA
0
C3030
0.0039 B C3027
71
2.6
0
0.1 F
0.1 F
0
2.6
22K
70
C3034
CAP_ON
69
0 1.3 1.2
F
C3021
C3029
0.0039 B
2.5
R3037
68
0.1
5.1
CAP_CTL 4.7K
67
83
66
CG_CS
CG_CLK
FF/REW SW
Q3008
KRC103SRTK
82
65
IIC_DATA
B
C3024
5.1
81
64
TAB_SW
R3036
63
0.01
5.1
33K
62
0
5.2
P.FAIL
REEL-S
61
CAP CTL
60
4.1 4.1 4.1 4.1 4.1 5.1 5.1 5.1 5.0
NC NC NC NC NC
PICTURE_CTL
59
C SYNC
V.REC ST-H
58
32KHz MONITER
57
IIC-SDA
56
IIC-CLK
55
10K
TAB SW
V.ENV
PERI_CTL/AGC
BOT
CAP_FWD
CAP_LIMIT
REMOCON
D.V SYNC
S.DET-H
SECAM_IN
DVD_RESET
VH SW
AH SW
POWER ON-H A
A.MUTE
CENT LED
SP-H
SECAM_H
FF/REW-L
54
CG-CLK
53
CG-DATA
52
SUB_CLK
51
1.0 2.0 3.0 3.0 4.0
0 2.0 5.0 3.0
NC NC NC NC NC NC NC NC
R3055
SUB DATA IN
NC
SUB DATA OUT
SEG 1
CFG
80 REEL-T
CG_CS
45
46
SUB_RESET
R3005
4
SEG 4
LDM CTL
ZERO MUTE
TP3001
53
79 REEL-S
GRID5
SERVICE 1
BOT
TAB_SW
SEG 3
GRID4
0
NC
52
DFG
78 CYL CTL
GRID3
5.1
SUB_RESET
EOT
SEG 2
GRID2
0
0
SERVICE2
SUB_CS
51
HIFI REC MUTE
44
0
AMP VSS
SERVICE1
47
EOT SENSOR
Q3002
ST-304L
5.1
BOT SENSOR
Q3001
ST-304L
2.5
CTL -
AMP V.OUT
48
4.5
CTL +
AMP V.IN
49
10K
SUB_CS
5.1
KEY-A
RESET
50
5.1
3
CTL VSS
REEL-T
XC OUT
5.1
R3013
MSSW_A
CYL_CTL
38
39
XC IN
5.1
10K
CAP_ON
32
33
34
35
36
F
100
R3007
5
VSS
1.2
MSSW_B
2
CTL AMP OUT
SYSCON/SOFTWARE/SERVO IC
IC3001
OEC7079D
SEG 10
RESET
X OUT
1.1
R3008
18P CH
37
1M
0
A VCC
100 MSECAM-M/AGC /
CTL SW OUT
MSECAM-M/S.DET
X IN
2.4
IIC_CLK
CTL AMP IN
GRID1
C3007
2.4
1
SUB_RESET
KA
C3035
AMP C
30 VV-H
SEG 9
CYL_CTL
VCC
5.1
SEG 8
CYL_CTL
CLKSEL
NA_REC-H
SUB_DATA_OUT
47
0 4.3 5.1 5.1 4.8 4.8
5
4
3
2
1
6
AMP VCC
28 DVD_MUTE
29
SEG 7
CYL_FG/PG
NC
SEG 6
CYL_FG/PG
NC
SEG 5
W807
DVD_POWER_C
40
LDM_CTL
18P CH
CAP_CTL
NC/PERI_CTL-L
41
10
C3010
DVD_POWER_A
43
CAP_CTL
F
470
0.1
LD/CY_VCO
9
0.1
R3009
18P CH
10M
8
C3009
CAP_LIMIT
C3038
0
5.1
C3011
1/4W
R3011
CAP_F/R
GND[M]
GND
12
3.3K
I LIMIT
7
11
R3006
X3002
CAP/M/F/R
100CT01207
VCC
4
R3010
3
18P CH
X3001
CAP_VCO
CAP_FG
100DA32R01
2
6
0
NC
0
NC
0
C3008
CAP_FG
5
31
DVD_POWER_A
CP3001
TMC-J12P-B2
6
5.0
FL_CS
YK
FROM/TO DECK
1
NC NC
NC
5.1
0
0 5.1 5.1 2.6 2.6 5.1 0
0
0
0 0.9 4.2
0 3.5
0 0 2.6 5.1
0
0
0 5.1
30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
8
7
42
35V 330
7
SUB_CS
1K
18K
R3021
27K
R3019
7
PERI_CTL-L
IIC_DATA
W875
CAP_VCO
AT+12.6V
FROM/TO TUNER/JACK
W810 MSECAM-M/AGC/S.DET
POWER_FAIL
CAP_F/R
CAP_LIMIT
REM_IN
S.DET-H
V.H_SW
DVD_RESET
CENT_LED
HIFI_H.SW
R3022
VCR_POWER_ON-H
VCR_POWER_ON-H
A_MUTE/TRICK-H
FL_CS
AT+5.2V
P.CON+5V
DVD_POWER_A
CAP_ON
MOTOR_GND
NA_REC-H
GND
DVD_MUTE
8
DUMMY_V.SYNC
8
HIFI_REC_MUTE
HIFI_ENV.DET
HIFI_H.SW
3
3
IIC_CLK
RESET
IIC_CLK
REEL-T
4
0
4.9
3
IN
GND
2
3
0
5.1
2
7
8
TEST
VCC
VSS
A2
A1
A0
4
0
4
18
0
3
0
2
0
1
0
47K
1SS133
6
SCL
F
5
SDA
D3002
5.1
0
R3040
17
3
1.3
18K 1/4W
33K
100
R3016
R3014
33K
4.9
1.3
1
C3028
MSSW_B
2
16V 10 KA
MSSW_A
R3012
DVD_MUTE
OUT
R3033
0
1.2
5.5V 0.047F
4
4.8
1.2
1
C3022
2.6
2
C3016
1
4
4.8
2.4
0.47
3
IC3099
S-24C08ADPA-01
1
3.8
2
3
TO DVD IN/OUT
4.9
EEP ROM IC
2
MS_SEN B
Q3004
RPI-352C40N
3.8
0
DVD_RESET
5.1
REEL SENSOR
Q3007 RPI-303
4.9
4
W887
NC
REEL SENSOR
Q3006 RPI-303
4.9
0
1
MS_SEN A
Q3005
RPI-352C40N
2
5
SYSTEM RESET IC
IC3004
PST3231NR
REEL-S
NC
NC
W809
W808 IIC_DATA
1/4W
47K
R3020
120 1/4W
R3018
47K 1/4W
R3017
IIC_DATA
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
PCB010
VMB252
CAUTION: DIGITAL TRANSISTOR
1
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
A
H-23
B
C
D
E
F
G
H
H-24
3
(0.6dB)
Gin CTL
CH
16
14
17
12
15
13
28
30
470P CH
25
26
8
10
23
24
4
6
9
11
7
22
2
3
5
1
10 AS
R303
IIC_CLK
IIC_DATA
470P CH
C8082
C8068
75
R8022
470P CH
31
12 SDA
14 +B
C303
CH
C307
16 TU
32
R8017
C8053
470 YK
470P CH
C8079
680
6.3V
6.3V
470 YK
470 YK
W861
2.2
R8023
R8032
2.2
W862
180
21 A.OUT
22 SIF
AFT_S.CURVE
C8065
23 AFT
24 V.OUT
R8037
1
2
0
3
NC
0
4
0
6
R8042
180
C8069
18K
10V 33 KA
OUTPUT2
INPUT2
NC
5
9.3
NC
8
0
9
NC
0
NF2
NF1
ALC
NC
GND
0
NC
1.8
1.8
12
11
10
NC
INPUT1
NC
OUTPUT1
100
W/ALC DUAL PRE-AMP IC
IC8003
BA3308F
0.1 B
C8039
1.8
R8074
0
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
1.8
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
16V 47 YK
C8083
0.022 B
100K
C8080
R8044
4.7K
C8075
10K
ARE
7
NC
10K 1/4W
R8026
16V 22 KA
4.2
4.9
R8075
KA
C8060
10K
13
3
C8072
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
100P CH
C8048
50V 1 KA
FRONT_V_IN
PERI_A_OUT-R
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
2
D
E
F
TU_V_OUT
PCB010
VMA252
FRONT_V_IN
SWD_VIDEO
TO Y/C/AUDIO/H.AMP
OSD_VIDEO
FROM SUB MICON/OSD/VPS
C_OUT
Y_OUT
DVD_B
DVD_G
DVD_R
SPDIF-134
DVD_A_OUT-R
DVD_A_OUT-L
DVD_V_OUT
FROM DVD IN/OUT
DEC_A-R
DEC_A-L
HIFI_A_OUT-R
HIFI_A_OUT-L
SWD_A-R
SWD_A-L
SIF_OUT
TU_A_OUT
FROM/TO HI-FI/DEMODULATOR
IIC_CLK
AFT_S.CURVE
IIC_DATA
FROM/TO VCR SYSCON
AT+12V
P.CON+5V
+32V
P.CON+9V
CAUTION: DIGITAL TRANSISTOR
FROM REGULATOR
PERI_A_OUT-L
4.2
MIXER
Q8006
KTC3875S_Y_RTK
R8025
50V 4.7
MIXER
Q8005
KTC3199_Y-AT 9.3
4.9
R8024
4.9
44
9.3
4.9
4.7K
43
100uH 0305
0
4
27
R8046
VCC
NC
14
3.9K
50V 1 KA
C8045
TUNER/DVD_VIDEO
SWD_A-R
C8041
50V 1 KA
50V 1 KA
SWD_A-L
PERI_A_IN-R
PERI_A_IN-L
C8033
C8038
50V 1 KA
C8032
50V 1 KA
50V 1 KA
C
20 SW2
SIF_OUT
16V 10 KA
0
L8016
10K
AMP
42
4.9
19 SW1
NC
TU_A_OUT
L8015
2.2
P.CON+9V
100K OHM
4.9
IC8001
LPF
LPF
4.9
NC
5
W863
R8031
R8020
4.9
18 NC
28
0.2,4,6dB
Gin CTL
41
17 NC
NC
TU_V_OUT
GND
0
40
NC
R8041
C8062
6.3V
AT+5.2V
5.5
39
15 NC
NC
CH
R8030
10K 1/4W
BUF
6
11 SCL
1K 1/4W
W865
R8033
R8018
38
9 NC
NC
10K
680
10K
4.5 NC 5.5
37
BUF
LPF
36
8 AGC
NC
NC
R8040
30
75
LA73026V
LPF
BUF
TCMI0600PD08D
6.3V
100K
1000 YK
R304
220P CH
C308
C302
0.01 F
C305
C8078
27
29
B
10K
BUF
MUTE
LPF
BUF
35
50V 1 KA
C8028
DEC_A_IN-R
31
32
0.022
NC
10uH
AV SWITCHES IC
BUF
W813
B
470P CH
C8081
C8073
18
19
R8027
DVD_G
B
A CD
SW2R
BUF
1
A
7 TU(MD)
1
R8019
5.5
34
36
29
C8051
AMP
5.5
DEC_A_IN-L
DEC_A_OUT-R
50V 1 KA
50V 1 KA
C8017
DVD_V_OUT
DEC_A_OUT-L
0305
100uH
C8016
AT+5.2V
0.01 B
L8004
C8023
0
34
1K
100P
B
4.9
33
100 YK
MUTE
EXT CTL4
32
0.1
4.9
31
38
33
R8034
FSS_OUT
NC
C8025
30
6 V.IN
6.3V
100P
C8059
ABC
SW1R
B
A CD
SW2L
AMP
Always Vcc
(5V -+ 0.5V)
5.1
AMP
CLAMP
2.0
C8011
DEC_V_OUT
AT+5.2V
PERI_VIDEO_OUT
L8002
0.01 B
0
29
6.3V 330 YK
2.1
C8009
47P CH
2.1
28
DEC_V_IN
5.1
6.3V 330 YK
C8102
PERI_VIDEO_IN
C8118
W901
C8008
2.2
27
0.2,4,6dB
Gin CTL
35
NC
DVD_B
LPF
NC NC NC
37
40
21
DVD_R
MUTE
BUF
7
R305
PERI_VIDEO_OUT
DECORDER/PERITEL
J8005 035_0_8183_00
C8057
10P CH
42
20
R8029
HIFI_A_OUT-R
1 B
2
ABC
SW3R
ABC
SW3L
Serial Control
ABC
SW1L
26
4
MUTE
MUTE
C8021
Control Vcc
(5V +
- 0.5V)
24
0.1 B
CLAMP
23
100uH 0305
3
H-25
39
41
5.5
100K OHM
AB C
SW3
AB CD
SW2
AMP
6dB
DR
75OHM LPF
AB C
SW1
AMP
6dB
DR
75OHM LPF
25
6
MUTE
MUTE
MUTE
2
75
R8021
C8116
10uH
D8007
1SS133
L8011
Y_OUT
1 B
C8049
C8047
C8040
50V 1 KANP
NC NC
-0.2
PERI_A_IN-L
Video SW3
MUTE
4
5
EXT CTL1
7
EXT CTL2
8
0 NC 5.5
LPF BUF
9
0 NC
MB
13 PB
AMP
10
470P
C8067
4.7
PERI_A_IN-R
1.6
4
C306
10K
HIFI_A_OUT-L
SWD_VIDEO
C_OUT
0.01 B
OSD_VIDEO
1 B
1 B
C8029
11
2.2
CLAMP
12
0 NC 0.2 NC 2.2
5.5
(Power Save CTL)
PWRSAV
13
5.5
C304
4.7
PERI_VIDEO_IN
(EXT MUTE CTL)
AUMUTE
14
4.9
To Audio Vcc
15
2.1
10.5V_REG
16
11.7
CLAMP
17
5.5
100K 110K
(L,M,H)
FCC_Control
18
5.5
CLAMP
19
0
To REF DC
(12V +- 0.5V)
Vcc 12V
2.1
EXT CTL3
20
CLOCK
DATA
21
0.2
SDA
5 SCL
R8068
4.7K
R8070
22
11.2
A.IN
3
W883
P.CON+5V
+32V
PERI_A_OUT-R
1.2
2
10K
4.7
-0.2
DVD_A_OUT-R
P.CON+5V
DVD_A_OUT-L
33P CH
1SS133
10K
1uH
75
C8043
D8006
10K
470P CH
L8007
0.27uH
2.2
R8015
D8005
D8004
MTZJ10B
L8006
0.27uH
15
R8013
B
470 YK
L8017
DVD RGB H OUT
Q8004
KRA102SRTK
PERI_A_OUT-L
1.3
KA
TU301
0.001 B
C8031
470
R8010
R8036
DEC_A_IN-L
P.CON+5V
10
25
1 BB
R302
R8045
DEC_A_IN-R
PERI_VIDEO_OUT
5
26
16V
75
DEC_V_IN
50V 1 KA
0.01 B
680
R8028
DEC_V_OUT
0.2
C8030
C8012 16V 470 YK
8
C301
RGB-H
C8027
0.01 B
AT+12V
100uH 0305
C8019
DVD_V_OUT
DEC_A-R
1 B
L8005
DEC_A-L
1 B
C8015
C8013
C8014
H
(SD-22VB)
680
DVD RGB H OUT
Q8003
DTC144EKA
C8036
100
0.01 B
RGB-H
1K
R8004
1.8K 1/4W
C8007
TUNER/DVD_VIDEO
FSS_OUT
R8001
470
R8009
6.3V
C8020
R8006
PERI_A_OUT-L
1.5
SPDIF-134
IIC_DATA
3
100uH
1.5
R8043
R8035
DEC_A_OUT-L
G
AT+5.2V
R8007
5.1
100P CH
IIC_CLK
1
10
C8005
6
2
0.001 B
C8026
1.1
10
MTZJ6.8B
5
6.3V
1.1
F
TUNER/JACK SCHEMATIC DIAGRAM (VCR PCB)
0.1
0
E
DEC_A_OUT-R
2
H2 H1
C8035
R8003
L8003
0.1 F
D8001
D AUDIO DRIVER
Q8002
KTC3875S_Y_RTK
120
R8005
C8002
6
PERI_A_OUT-R
100uH
L8001
68
D AUDIO
DRIVER
Q8001
KTA1504S_Y_RTK
1
4
47 KA
R8002
6.3V 47 KA
7
C8010
0.1 F
C8004
3
34
H
C8018
B8001
220P CH
E
0.022 B
2
C8006
C8003
E
1
0.1 F W4BRH3.5X6X1
3 GND
2 VCC
1 INPUT
COAXIAL
J8001
MSP-251V-05PBSN
OPT TRNSFORMER
OS8001
GP1FA550TZ
8
D
Y/C SEPA
J8003
MDC-070V
6.3V 100 YK
C310_1
C
AUDIO OUT
J8002
MSP-242V2-01PBSN
470P CH
B
MTZJ10B
A
CAUTION: DIGITAL TRANSISTOR
1
G
H
H-26
H-27
A
B
50V 4.7 KA
C8022
0
NC
4.2
16V 10 KA
BUFFER
4.8
BAIAS
VCC
4.0
9.3
0.8
C
16V
0
C8050
22 KA
NC
D
R8023
R8032
2.2
E
R8027
13
2.2
12
NC
R8034
30
680
30
11
10
9
27
28
8
7
R8040
31
680
25
26
6
5
23
24
4
22
3
2
1
DECORDER/PERITEL
J8005 035_0_8183_00
C8073
470P CH
10K
NC
IIC_DATA
W861
W862
W863
10uH
LPF
F
TU_V_OUT
2.2
14
4.7
4.7
NC
IIC_CLK
4.9
44
FRONT_V_IN
6.3V 1000 YK
0.01 F
C310_1
220P CH
C308
C305
C8078
26
1 BB
R8028
R8039
NC
33K
P.CON+5V
NC
+32V
W864
W865
NC
10K
R8030
32
1
SW1
W815
SW2
W816
L8015
TU_V_OUT
MUTE
28
G
25
2
A.IN
3
SDA
4
MB
W883
NC
8 AGC
NC
9 NC
NC
17 NC
NC
18 NC
TU_A_OUT
21 A.OUT
SIF_OUT
22 SIF
AFT_S.CURVE
23 AFT
TCPL0601PD08D
F
TU301
C302
C8067
470P CH
6.3V 100 YK
AT+5.2V
FRONT_V_IN
R8017
15
32
470P CH
C8081
680
SWD_VIDEO
29
680
TO Y/C/AUDIO/HEAD AMP
PERI_A_OUT-R
16
22K
R8045
OSD_VIDEO
PERI_A_IN-L
34
29
C_OUT
PERI_VIDEO_IN
17
R8066
W878
FROM SUB MICON/OSD/VPS
75
18
31
Y_OUT
19
36
470P CH
E
DVD_B
PERI_A_IN-R
38
33
DVD_G
PERI_A_OUT-L
40
35
DVD_R
20
37
470P CH
21
39
NC NC NC
C8082
10K
10K
470P CH
NC NC
C8079
-0.2
(VCR PCB)
SPDIF-134
6.3V 470 YK
1uH
D8013
MTZJ4.7B
R8036
DVD_A_OUT-R
6.3V 470 YK
42
C8068
L8017
470P CH
DEC_A_IN-R
DVD_A_OUT-L
5.5
C8062
75
DVD_V_OUT
C8053
75
R8035
CH
C8072
C8051
41
470P CH
PERI_VIDEO_OUT
10P CH
DEC_A_IN-L
R8043
100P
FSS_OUT
C8116
DEC_A_OUT-R
FROM DVD IN/OUT
C8059
33P CH
R8021
PERI_CTL-L
DEC_A-R
6.3V 470 YK
10uH
C8057
DEC_A_OUT-L
DEC_A-L
DVD_B
L8011
5
HIFI_A_OUT-R
DVD_G
75
R8022
L8007
0.27uH
TUNER/JACK SCHEMATIC DIAGRAM
SWD_A-R
LPF
D8007
-0.2
R8068
1SS133
2.2
R8015
3
SWD_A-L
DVD_R
75
C8043
6.3V 470 YK
L8006
0.27uH
D
HIFI_A_OUT-L
0.2,4,6dB
Gin CTL
R8029
0.2
SIF_OUT
43
B
Y_OUT
DEC_V_OUT
TU_A_OUT
4.9
1
HIFI_A_OUT-R
HIFI_A_OUT-L
MTZJ10B
D8005
MTZJ10B
D8004
15
R8013
DEC_V_IN
FROM/TO HI-FI/DEMODULATOR
42
1 B
C8049
C8047
SW1
RGB-H
IIC_CLK
BUF
DVD RGB H OUT
Q8004
KRA102SRTK
AFT_S.CURVE
NJM2533V
4.9
BUF
1SS133
IIC_DATA
TU/REAR VIDEO IN SW IC
W896
DVD RGB H OUT
Q8003
DTC144EKA 4.7
PERI_CTL-L
MUTE
BUF
D8006
FROM/TO VCR SYSCON
C8109
47K
SW2
SWD_VIDEO
B
C
GND
Video SW3
AT+5.2V
47P CH
41
2
AT+12V
MUTE
P.CON+5V
P.CON+5V
4.9
5.5
+32V
BUF
3
IC8001 LA73026V
MUTE
EXT CTL1
EXT CTL2
50V 1 KA
P.CON+9V
40
1
FROM REGULATOR
4.9
0
100K OHM
LPF
ABC
SW3R
4
AV SWITCHES IC
MUTE
B
A CD
SW2R
0
AMP
LPF
ABC
SW1R
C8040
50V 1 KANP
W895
10
47uH
0305
39
5
50V 1 KA
AMP
1.6
3.3K
R8073
R8072
0.1
C8035
2
PERI_A_OUT-R C8048
4.9
4
P.CON+9V
38
J8003
MDC-070V
L8008
0
100K OHM
LPF BUF
C_OUT
0.001 B
6
F
4.8
6
KA
37
(0.6dB)
Gin CTL
AMP
OSD_VIDEO
C8031
0.001 B
H2 H1
2
0.1
IC8002
5.5
0.01 B
C8036
470
R8010
1
50V 1
36
Y/C SEPA
PERI_A_OUT-L C8045
5.5
2.2
TUNER/DVD_VIDEO
35
7
LPF
BUF
CLAMP
C8030
BUF
BUF
8
50V 1 KA
LPF
MUTE
(Power Save CTL)
PWRSAV
9
C8041
4.5
470
R8009
C8026
AUDIO OUT J8002
MSP-242V2-01PBSN
SWD_A-R
NC
BUF
MUTE
PERI_A_OUT-R
PERI_A_OUT-L
6.3V 47 KA
B
C8046
C8024
0 NC 0.2 NC 2.2
50V 1 KA
34
1 B
100uH
5.1 R8007
C8038
5.5
10
SWD_A-L
33
5.5
8
5.5
(EXT MUTE CTL)
AUMUTE
11
50V 1 KA
C8033
50V 1 KA
32
DVD_A_OUT-R
DVD_A_OUT-L
C8018
C8020 0.022 B
3
PERI_A_IN-R
0
5.5
4.7K
31
12
R8071
4.9
4.9
1.8K
C8032
0.01 B
PERI_A_IN-L
0.2,4,6dB
Gin CTL
EXT CTL4
MUTE
ABC
SW3L
13
1 B
C8029
L8003
34
7
1
B
A CD
SW2L
2.1
C8027
P.CON+5V
B8001
0.1 F W4BRH3.5X6X1
C8010
E
6
2
30
DVD_V_OUT
120
R8005
COAXIAL
J8001
MSP-251V-05PBSN
3 GND
2 VCC
1 INPUT
E
5
3
ABC
SW1L
14
R8011
11.7
To Audio Vcc
15
10.5V_REG
C8012 16V 470 YK
0.01 B
AT+12V
100
SW3
4.9
R8006
50V 1 KA
C8028
50V 1 KA
29
D AUDIO DRIVER
Q8002
KTC3875S_Y_RTK
DEC_A_IN-R
5.1
5.5
DEC_A_IN-L
16
100uH
0305
100P CH
CLAMP
C8014
C8019
1.5
B
28
1.1
0.1
2.0
DEC_A-R
10
C8025
5.5
AMP
17
1 B
L8005
1.5
H
TU_V_OUT
27
C8023
0
1.1
50V 1 KA
18
To REF DC
(12V +- 0.5V)
Vcc 12V
DEC_A-L
68
D AUDIO
DRIVER
Q8001
KTA1504S_Y_RTK
1 B
C8015
R8002
AMP
MUTE
Serial Control
0.1 F
C8004
DEC_A_OUT-R
0
C8013
C8006
50V 1 KA
C8017
26
0.01 B
C8005
2
DEC_A_OUT-L
2.1
0
Always Vcc
(5V -+ 0.5V)
RGB-H
220P CH
100uH 0305
C8016
25
R8003
AT+5.2V
2.1
2.1
100K 110K
19
CLAMP
0.2
1.8K 1/4W
C8007
TUNER/DVD_VIDEO
1K
R8004
MTZJ6.8B
CLAMP
20
EXT CTL3
D8001
0.01 B
L8004
24
F
6.3V 330 YK
AB C
SW3
C8002
DEC_V_IN
4
AB CD
SW2
6.3V 47 KA
C8021
AB C
SW1
11.2
C8011
AMP
6dB
FSS_OUT
100uH
L8001
C8003
1
4
1
DR
75OHM LPF
(L,M,H)
FCC_Control
21
0.1 B
5.1
AMP
6dB
R8001
SPDIF-134
0.1
DEC_V_OUT
23
DR
75OHM LPF
1.2
C8009
2.2
IIC_DATA
IIC_CLK
7
PERI_VIDEO_OUT
22
100uH
0305
CLOCK
DATA
1.3
Control Vcc
(5V +
- 0.5V)
CLAMP
OPT TRNSFORMER
OS8001 GP1FA550TZ
SW3
DVD_V_OUT
2
4.7K
8
AT+5.2V
3
W901 6.3V 330 YK
C8102
0
0.01 B
L8002
47P CH
C8118
5
R8070
6
PERI_VIDEO_IN
C8008
A
(SD-22VE)
G
H
8
5 SCL
6 V.IN
7
C306
7 TU(MD)
0.022 B
10 AS
11 SCL
12 SDA
6
13 PB
15 NC
14 +B
10K
16 TU
R8041
5
19 SW1
20 SW2
24 V.OUT
27
4
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
3
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
2
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
PCB010
VMB252
1
H
H-28
E
F
5
(0.6dB)
Gin CTL
3
C307
17 NC
NC
18 NC
470P CH
C8068
470P CH
C8082
5
470P CH
NC
19 SW1
NC
20 SW2
TU_A_OUT
21 A.OUT
SIF_OUT
22 SIF
AFT_S.CURVE
180
C8065
R8037
16V 10 KA
3.9K
23 AFT
24 V.OUT
10K
PERI_A_OUT-L
0
4
5
0
9.3
6
NC
180
R8042
C8069
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
10V 33 KA
NC
NC
OUTPUT2
INPUT2
NF2
ALC
NC
3
NC
VCC
NF1
NC
INPUT1
NC
W/ALC DUAL PRE-AMP IC
IC8003
BA3308F
100
R8075
GND
0
18K
NC
8
7
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
1.8
10K
16V 47 YK
10K 1/4W
R8026
3
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
2
E
F
PCB010
VMB252
FRONT_V_IN
TU_V_OUT
SWD_VIDEO
TO Y/C/AUDIO/HEAD AMP
OSD_VIDEO
FROM SUB MICON/OSD/VPS
C_OUT
Y_OUT
DVD_B
DVD_G
DVD_R
SPDIF-134
DVD_A_OUT-R
DVD_V_OUT
DVD_A_OUT-L
DEC_A-R
DEC_A-L
HIFI_A_OUT-R
HIFI_A_OUT-L
SWD_A-R
SWD_A-L
SIF_OUT
IIC_CLK
AFT_S.CURVE
IIC_DATA
PERI_CTL-L
GND
AT+12V
P.CON+5V
AT+5.2V
D
FROM/TO SYSCON2
C8050
FROM/TO HI-FI/DEMODULATOR
RECORD LUMINANCE SIGNAL
47uH 0305
L8008
0.1 F
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
P.CON+9V
TUNER/DVD_VIDEO
C8046
C
2
0
RECORD COLOR SIGNAL
FROM REGULATOR
5
NC
0
9
FRONT_V_IN
16V 22 KA
0.8
1
0
0.022 B
C8083
4.9
1.8
NC
1.8
1.8
12
11
10
100K
C8080
4.2
R8074
0
R8044
4.9
0.1 B
R8025
50V 4.7
4.2
13
CH
50V 1 KA
C8048
4.9
C8060
MIXER
Q8005
2SC1740SP 9.3
MIXER
Q8006
2SC2412K
0
100P
50V 1 KA
C8045
9.3
14
C8072
50V 1 KA
C8041
SWD_A-R
KA
L8016
100uH 0305
0
4
27
R8046
PERI_A_OUT-R
50V 1 KA
C8038
SWD_A-L
BAIAS
TU301
16 TU
NC
L8015
C8039
44
6
VCC
15 NC
NC
32
W863
16V 22 KA
4.9
TCMB0601PD13D
6.3V
100K
1000 YK
R304
220P CH
C308
0.01 F
C305
100 YK
C310_1
C302
6.3V
CH
470P
C8073
22K
R8066
MTZJ4.7B
D8013
75
R8021
75
2.2
2.2
8
7
2
9.3
4.8
4
14 +B
C303
W862
C8075
4.9
50V 1 KA
4.0
BUFFER
3
B
R8023
4.7K
AMP
43
P.CON+9V
R8024
4.9
42
C8033
PERI_A_IN-R
PERI_A_IN-L
SW3
1
4.2
NC
2.2
6.3V 470 YK R8032
0
16V 10 KA
A
41
1.8K
50V 1 KA
NJM2533V
4.8
0
12 SDA
W861
NC
4.7K
4.9
100K OHM
40
4.9
LPF
0.2,4,6dB
Gin CTL
C8032
R8071
R8011
50V 1 KA
C8028
DEC_A_IN-R
50V 1 KA
DEC_A_IN-L
TU_V_OUT
SW3
DVD_V_OUT
C8025
0.1 B
C8023
1 KA
C8017 50V
DEC_A_OUT-R
1 KA
50V
C8016
DEC_A_OUT-L
IC8002
50V 4.7 KA
31
680
OUTPUT1
BUF
BUF
6
1K 1/4W
R8041
R8031
R8020
0
39
C8109
C8022
11 SCL
W865
R8030
R8017
6.3V 470 YK
10K
5.5
38
TU/REAR VIDEO IN SW IC
1
C8059
R8019
5.5
37
47P CH
C8024
R303
IIC_CLK
IIC_DATA
R8040
680
6.3V 470 YK C8053
10K
36
4.5
1
TU_V_OUT
R8018
35
5.5
3
10K
10K 1/4W
LPF
LPF
EXT CTL4
5.5
2
5
9 NC
10 AS
R8033
+32V
0
34
7
22
8 AGC
NC
NC
30
75
C8051
P.CON+9V
4.9
33
4
6
9
NC
10K
IC8001
MUTE
LPF
NC
32
LPF
4.7K
4.9
31
8
10
11
24
B
28
AMP
BUF
BUF
30
26
23
10uH
AV SWITCHES IC
B
A CD
SW2R
BUF
BUF
AMP
Always Vcc
(5V +
- 0.5V)
AT+5.2V
DEC_V_IN
DEC_V_OUT
5.1
L8004 100uH 0305
C8021
2.0
AMP
CLAMP
29
C8011
0.01 B
100uH 0305
0
28
6.3V 330 YK
2.1
C8009
2.1
27
7 TU(MD)
MUTE
ABC
SW1R
B
A CD
SW2L
ABC
SW1L
AMP
6dB
DR
75OHM LPF
26
PERI_VIDEO_OUT
AT+5.2V
PERI_VIDEO_IN
C8008
5.1
C8118 W901 6.3V 330 YK
C8102
0.01 B
L8002
47P
CH
2.2
3
25
0.1 B
Control Vcc
(5V -+ 0.5V)
24
DR
75OHM LPF
CLAMP
23
0.2,4,6dB
Gin CTL
12
13
25
DECORDER/PERITEL
J8005 035_0_8183_00
R8029
R8022
29
LA73026V
ABC
SW3R
ABC
SW3L
Serial Control
MUTE
14
15
R8027
DVD_G
100K OHM
AB C
SW3
AB CD
SW2
AB C
SW1
MUTE
6 V.IN
100P CH
FSS_OUT
MUTE
7
1K
6.3V 100 YK
1
BUF
MB
R305
+32V
100P CH
DVD_B
LPF
C304
0.022
28
30
R8034
DVD_R
MUTE
BUF
4
5 SCL
PERI_VIDEO_OUT
27
29
32
NC
5.5
2
34
16
17
C8062
0 NC 5.5
4
SDA
22uH 0305
NC
31
470P CH
0 NC
1.6
6
EXT CTL1
2.2
7
MUTE
MUTE
AMP
6dB
2.2
8
Video SW3
MUTE
4
NC
0.2
9
EXT CTL2
NC
0
10
LPF BUF
5.5
11
AMP
5.5
12
CLAMP
4.9
13
(Power Save CTL)
PWRSAV
2.1
14
33
36
18
PERI_VIDEO_IN
(EXT MUTE CTL)
AUMUTE
11.7
15
To Audio Vcc
5.5
16
10.5V_REG
5.5
17
38
19
PERI_A_IN-R
50V 1 KA
CLAMP
0
18
To REF DC
(12V +- 0.5V)
Vcc 12V
(L,M,H)
FCC_Control
CLOCK
DATA
2.1
19
100K 110K
0.2
20
CLAMP
11.2
21
EXT CTL3
R8070
10P CH
10uH
C8057
L8011
1SS133
D8007
Y_OUT
HIFI_A_OUT-R
C8047
20
21
35
PERI_A_IN-L
4.7K
1.2
A.IN
3
13 PB
1B
C8049
HIFI_A_OUT-L
SWD_VIDEO
50V 1 KANP
C8040
10K
NC NC NC
37
40
PERI_A_OUT-R
22
H-29
42
PERI_A_OUT-L
1.3
2
39
41
75
R8015
D8005
MTZJ10B
D8004
MTZJ10B
R8013
B
C_OUT
0.01 B
OSD_VIDEO
C8036
1B
1B
C8029
NC NC
-0.2
R8068
2
10K
C306
PERI_VIDEO_OUT
5
470P CH
C8067
4.7
4.7
-0.2
C8030
C8116
1SS133
33P CH
D8006
1uH
25
L301
P.CON+5V
470P
CH
C8081
L8007
L8006
0.27uH
0.001 B
C8031
0.27uH
P.CON+5V
26
R302
10 KA
10K
10K
L8017
TU_A_OUT
0.01 B
R8045
0.2
DVD_A_OUT-R
P.CON+5V
C8019
C8012
DVD_A_OUT-L
YK
C8027
100uH 0305
470
DVD_V_OUT
1
B
L8005
16V
0.01 B
1 B
C8015
AT+12V
DEC_A-R
C8013
DEC_A-L
TUNER/DVD_VIDEO
0.01 B
C8014
16V
R8036
DVD RGB H OUT
Q8004
KRA102SRTK
8
33K
DEC_A_IN-L
RGB-H
PERI_A_OUT-R
100
R8004
C8007
1.8K
1/4W
RGB-H
FSS_OUT
1K
R8001
R8039
75
H
1 BB
C301
R8028
DVD RGB H OUT
Q8003
4.7
DTC144EKA
PERI_A_OUT-L
L8003
R8006
AT+5.2V
W878
PERI_CTL-L
100uH
1.5
SPDIF-134
IIC_DATA
470
R8010
R8007
5.1
100P CH
IIC_CLK
680
DEC_A_IN-R
10
1.5
C8005
6
0.001 B
C8026
1.1
G
(SD-22VL)
680
R8035
DEC_A_OUT-L
3
1B
1.1
R8043
DEC_A_OUT-R
1
4
DEC_V_OUT
470
C8010
0
2
C8043
MTZJ6.8B
10
Y/C SEPA
J8003
MDC-070V
5
6.3V 470 YK 2.2
R8003
6
C8035
D8001
2
H2 H1
R8009
0.1 F
D AUDIO DRIVER
Q8002
2SC2412K
6.3V 47 KA
C8002
L8001
7
D AUDIO
DRIVER
Q8001
2SA1037AK
120
68
R8005
100uH
R8002
47 KA
1
DEC_V_IN
C8018
B8001
220P CH
3
H
C8020 0.022 B
2
0.1 F
C8004
6.3V
E
34
C8006
C8003
E
15
1
0.1 F W4BRH3.5X6X1
3 GND
2 VCC
1 INPUT
OS8001 GP1FA550TZ
0.1
COAXIAL
J8001
MSP-251V-05PBSN
8
AUDIO OUT
J8002
MSP-242V2-01PBSN
TUNER/JACK SCHEMATIC DIAGRAM
OPT TRNSFORMER
(VCR PCB)
C8078
D
470P CH
C
C8079
B
FROM DVD IN/OUT
A
CAUTION: DIGITAL TRANSISTOR
G
CAUTION: DIGITAL TRANSISTOR
1
H
H-30
A
B
C
D
E
F
G
H
REGULATOR SCHEMATIC DIAGRAM
(VCR PCB)
(SD-22VB)
8
8
W822
CAP_VCO
R1722
2.2K 1/2W
D1711
7
1N4005-EIC
AT+12.6V
7
MOTOR_GND
AT+5.2V
5.2
5.0
5.9
P.CON+5V
P.CON+12V
GND
180 1/2W
5.2
P.CON+5V_DH
P.CON+5V SW
Q1702
KTC3209_Y
5.2
R1709
M-CON +5V SW
Q1713
KTA1271_Y
AT+5V[M-CON]
4.5
TO OPERATION/DISPLAY
M-CON POWER SW
Q1714
KRC103SRTK
0
6
-22V
0
6.3V
C1713
100 YK
390 1/4W
6
5.1
1K
1/4W
5.9
AT+12V
R1708
R1721
5.2
TO HI-FI/DEMODULATOR
P.CON+5V
P.CON+5V SW
Q1703
KTC3209_Y
HEATER_DC+
5.2
HEATER_DC-
POWER_FAIL
AT+5.2V
GND
DVD_POWER_A
3.3V OUT
Q1706
KTA1241_Y
R1714
100
R1715
820
+-1%
C1707
GND
5
FROM/TO VCR SYSCON
CAP_VCO
AT+12.6V
470 YK
AT+5.2V
6.3V
C1711
C1710
6.3V 470 YK
AT+5V[M-CON]
R1711
2.2K
R1707
1.2
3.3V CTL
Q1705
KTC3875S_Y_RTK
R1716
1.8
3.3V CTL 4.1
Q1707
KTC3875S
1.9
Y_RTK
1.2
P.CON+5V
1.2K +-1%
3.5
35V 22 YK
3.5
100 1/4W
R1706
3.9K 1/4W
5
TO Y/C/AUDIO/HEAD AMP
P.CON+3.3V
3.4
4.1
MOTOR_GND
P.CON+5V
POWER_FAIL
VCR_POWER_ON-H
GND
4
4
CP1701_1 (CP502)
52147-1610
8
UNREG+3.3V
9
POWER_ON_H
10
GND
11
GND
12.4
R1703
10K 1/4W
C1712
50V 10 YK
MTZJ10B
D1710
12.6
TO DVD IN/OUT
AT+5.2V
R1720
P.CON+9V
560 1/4W
P.CON+5V_DH
9.9
GND
9.3
P.CON+12V
220
1/4W
12.6
TO TUNER/JACK
TUNER+32V
14
-22V
15
HEATER -
16
HEATER +
3
GND
AT+5.2V
P.CON+5V
AT+5.2V
AT+12V
P.CON+9V
+32V
TO SUB MICON/OSD/VPS
AT+12V
P.FAIL
13
P.CON+3.3V
P.CON+9V
10K
1/4W
UNREG+3.3V
1SS133
R1713
AT+5.2V
7
12V REG.
Q1701
KTC3203_Y
C1714
6
12
2
AT+5.2V
W890
16V 470 YK
5
11.8
P.CON+9V SW
Q1712
D1709 KTC3209_Y
POWER_FAIL
P.CON+12V
13.5
13.5
AT+13V
C1703
4
D1703
MOTOR_GND
MTZJ12B 1SS133
MOTOR+12V
3
D1702
2
W818
16V 10 KA
3
5.1
P.CON+12V SW
Q1708
13.2
KTC3209_Y
R1712
NC
0
P.ON SW
Q1709
KRC103SRTK
0
0
22K 1/4W
13.6
FROM/TO POWER
1
0
R1717
50V 1 YK
C1708
MTZJ13B
D1708
DVD_POWER_A
P.ON SW
Q1711
KRC103SRTK
+32V
W820
GND
-22V
P.CON+5V
HEATER_DC-
AT+5.2V
HEATER_DC+
2
PCB010
VMA252
CAUTION: DIGITAL TRANSISTOR
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
A
H-31
B
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
D
E
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
F
ARE
1
G
H
H-32
A
B
C
D
E
F
G
H
REGULATOR SCHEMATIC DIAGRAM
(VCR PCB)
(SD-22VE)
8
R1702
D1712
CAP_VCO
1SS133
C1702
W823
35V 100 YK
R1701
W817
2W
3.3K 1/2W
2.7
8
+32V
D1711
AT+12.6V
1N4005-EIC
MOTOR_GND
7
7
AT+5.2V
5.2
5.0
P.CON+5V
P.CON+5V SW
Q1703
KTC3209_Y
5.9
R1708
5.2
GND
P.CON+5V_DH
P.CON+5V SW
Q1702
KTC3209_Y
5.9
P.CON+5V
P.CON+12V
180 1/2W
5.2
R1709
5.1
M-CON +5V SW
Q1713 KTA1271_Y
100 YK
M-CON POWER SW
Q1714
KRC103SRTK
6.3V
C1713
R1721
390 1/4W
6
AT+5V[M-CON]
4.5
TO OPERATION/DISPLAY
1K 1/4W
5.2
TO HI-FI/DEMODULATOR
AT+12V
-22V
0
HEATER_DC+
6
HEATER_DC-
POWER_FAIL
5.2
AT+5.2V
GND
DVD_POWER_A
3.3V OUT
Q1706
KTA1241_Y
100
GND
820
+-1%
3.3V CTL 4.1
Q1707
KTC3875S
1.9
Y_RTK
1.2
P.CON+5V
5
FROM/TO VCR SYSCON
CAP_VCO
AT+12.6V
AT+5.2V
C1711
6.3V 470 YK
C1710
1.2K
+-1%
R1716
R1711
100 1/4W
AT+5V[M-CON]
2.2K
R1707
1.2
3.3V CTL
Q1705
KTC3875S_Y_RTK
6.3V 470 YK
1.8
R1715 R1714
C1707
3.5
3.5
35V 22 YK
R1706
3.9K 1/4W
5
TO Y/C/AUDIO/HEAD AMP
P.CON+3.3V
3.4
4.1
P.CON+5V
POWER_FAIL
MOTOR_GND
VCR_POWER_ON-H
GND
13.6
POWER ON H
10
GND
11
GND
13
14
C1712
50V 10 YK
D1710
AT+5.2V
R1720
P.CON+9V
560 1/4W
P.CON+5V_DH
9.9
GND
9.3
TO TUNER/JACK
AT+5.2V
AT+12V
P.CON+9V
+32V
HEATER +
TO SUB MICON/OSD/VPS
AT+12V
+32V
W820
-22V
16
3
GND
P.CON+5V
P.FAIL
HEATER -
P.CON+12V
AT+5.2V
TUNER+32V
15
P.CON+3.3V
P.CON+9V
220 1/4W
9
10K 1/4W
TO DVD IN/OUT
10K 1/4W
UNREG+3.3V
12.6
R1713
UNREG+3.3V
8
C1714
7
12.4
R1703
D1703
AT+5.2V
12V REG.
Q1701
KTC3203_Y
1SS133
AT+5.2V
6
W890
11.8
MTZJ12B
5
12
13.5
AT+13V
16V 470 YK
MOTOR GND
D1702
4
12.6
4
POWER_FAIL
P.CON+12V
13.5
16V 10 KA
3
3
W818
MOTOR+12V
C1703
2
P.CON+9V SW
Q1712
D1709 KTC3209_Y
1SS133
P.CON+12V SW
Q1708
13.2
KTC3209_Y
R1712
CP1701_1 (CP502)
52147-1610
1
MOTOR+24V
5.1
0
22K 1/4W
P.ON SW
Q1709
KRC103SRTK
0
R1717
50V 1 YK
C1708
MTZJ13B
D1708
0
0
FROM/TO POWER
P.ON SW
Q1711
KRC103SRTK
MTZJ10B
DVD_POWER_A
4
GND
-22V
HEATER_DC-
AT+5.2V
HEATER_DC+
2
2
PCB010
VMB252
CAUTION: DIGITAL TRANSISTOR
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
A
H-33
B
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
D
E
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
F
ARE
1
G
H
H-34
A
B
C
D
E
F
G
H
REGULATOR SCHEMATIC DIAGRAM
(VCR PCB)
(SD-22VL)
8
R1702
CAP_VCO
D1712
1SS133
C1702
W823
35V 100 YK
W817
2W
3.3K 1/2W
R1701
2.7
8
+32V
D1711
7
7
AT+12.6V
1N4005-EIC
MOTOR_GND
AT+5.2V
5.2
5.0
5.9
P.CON+5V SW
Q1703
KTC3209_Y
GND
P.CON+5V_DH
5.2
C1713
390 1/4W
M-CON +5V SW
Q1713
KTA1271_Y
6.3V 100 YK
R1709
5.1
AT+5V[M-CON]
4.5
-22V
0
M-CON POWER SW
Q1714
KRC103SRTK
6
TO OPERATION/DIPLAY
1K
1/4W
P.CON+5V SW
Q1702
KTC3209_Y
5.9
P.CON+5V
P.CON+12V
180 1/2W
5.2
6
TO HI-FI/DEMODULATOR
AT+12V
R1708
R1721
5.2
P.CON+5V
HEATER_DC+
HEATER_DC-
POWER_FAIL
5.2
AT+5.2V
0
GND
DVD_POWER_A
3.3V OUT
Q1706
KTA1241_Y
R1714
100
820
+-1%
GND
FROM/TO SYSCON2
CAP_VCO
1.2
AT+12.6V
470 YK
AT+5.2V
P.CON+5V
POWER_FAIL
6.3V
C1711
470
YK
AT+5V[M-CON]
6.3V
C1710
+-1%
R1711
100 1/4W
2.2K
5
P.CON+5V
1.9
1.2
3.3V CTL
Q1705
2SC2412K
R1707
R1715
C1707
4.1
3.3V CTL
Q1707
2SC2412K
R1716
3.5
1.8
35V 22 YK
1/4W
R1706
3.9K
3.4
3.5
1.2K
4.1
5
TO Y/C/AUDIO/HEAD AMP
P.CON+3.3V
MOTOR_GND
VCR_POWER_ON-H
4
CP1701_1 (CP502)
52147-1610
2
8
UNREG+3.3V
9
POWER ON H
10
GND
11
GND
12
P.FAIL
13
TUNER+32V
14
-22V
15
HEATER -
16
HEATER +
22K 1/4W
R1717
C1712
50V 10 YK
D1710
YK
MTZJ10B
P.CON+9V
9.9
P.CON+5V_DH
11.8
12.4
R1703
10K 1/4W
W890
12V REG.
Q1701
KTC3203_Y
P.CON+3.3V
P.CON+9V
GND
9.3
P.CON+12V
12.6
3
TO TUNER/JACK
220 1/4W
UNREG+3.3V
AT+5.2V
R1720
560 1/4W
GND
AT+5.2V
P.CON+5V
AT+5.2V
10K 1/4W
7
12.6
TO DVD IN/OUT
13.2
R1712
AT+5.2V
P.CON+9V SW
Q1712
D1709 KTC3209_Y
1SS133
R1713
AT+5.2V
6
13.5
13.5
C1714
5
POWER_FAIL
P.CON+12V
16V 470 YK
AT+13V
D1703
MOTOR GND
4
MTZJ12B1SS133
3
5.1
DVD_POWER_A
W818
16V 10 KA
MOTOR+12V
D1702
2
P.CON+12V SW
Q1708
KTC3209_Y
C1703
3
MOTOR+24V
0
13.6
FROM/TO POWER
1
0
50V 1
MTZJ13B
C1708
D1708
0
P.ON SW
Q1709
KRC103SRTK 0
4
GND
P.ON SW
Q1711
KRC103SRTK
AT+12V
P.CON+9V
+32V
TO SUB MICON/OSD/VPS
AT+12V
+32V
W820
GND
-22V
HEATER_DC-
2
AT+5.2V
HEATER_DC+
PCB010
VMB252
CAUTION: DIGITAL TRANSISTOR
1
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
A
H-35
B
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
C
D
E
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
F
1
ARE
G
H
H-36
A
B
C
D
E
F
G
H
OPERATION/DISPLAY SCHEMATIC DIAGRAM
(VCR PCB)
8
8
7
7
FROM/TO DISPLAY PCB
CP651 (CP8501)
IMSA-9604S-18Z14
1
6
GND
3
FRONT_A_IN_L
4
GND
5
FRONT_A_IN_R
6
GND
7
KEY-A
8
KEY-B
REM_IN
11
AT+5.2V
12
GND
14
15
16
FROM SUB MICON/OSD/VPS
FRONT_A_IN-L
DVD_LED
FRONT_A_IN-R
W873
VCR_LED
KEY-A
CG_CLK
REM_IN
FL_CS
SEG_10
KEY-A
HEATER_DC+
HEATER_DC+
-22V
KEY-B
FL_CS
FL_CS
HEATER_DC-
REM_IN
CG_DATA
FL_DATA
18
CG_DATA
CG_CLK
FL_CLK
17
6
FROM/TO VCR SYSCON
KEY-B
NC
9
10
13
FRONT_V_IN
FRONT_V_IN
2
HEATER_DC-22V
C651
5
5
SEG_10
5.0
35V 47 YK
5.2
5.2
TO HI-FI/DEMODULATOR
FIP ON SW
Q652
KRA102SRTK
FRONT_A_IN-L
FRONT_A_IN-R
TO Y/C/AUDIO/HEAD AMP
S804X
S804Y
VCR_LED
FRONT_V_IN
FROM/TO OPERATION1/LED
4
NC
1
VCR_LED
3
DVD_LED
4
GND
5
AT+5.2V
6
KEY-A
7
KEY-B
0
DVD_LED
FROM REGULATOR
GND
5.2
-22V
KEY-A
W892
W893
W894
HEATER_DC+
KEY-B
HEATER_DCR666
2
DVD/HDD LED SW
Q651
KRA103SRTK
5.1
R667
3
10K
CP653 (CP8502)
IMSA-9604S-07Z13
AT+5.2V
3
10K
4
2
2
CAUTION: DIGITAL TRANSISTOR
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
PCB010
VMA252
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
1
A
H-37
B
C
D
E
F
G
H
H-38
A
B
C
D
E
F
G
H
HI-Fi/DEMODULATOR SCHEMATIC DIAGRAM
(VCR PCB)
DVD_A_OUT-R
DVD_A_OUT-L
FROM DVD IN/OUT
FRONT_A_IN-R
FRONT_A_IN-L
FROM OPERATION/DISPLAY
SIF_OUT
TU_A_OUT
DEC_A-R
DEC_A-L
HIFI_A_OUT-R
HIFI_A_OUT-L
SWD_A-R
SWD_A-L
FROM/TO TUNER/JACK
HF_COM
HF2
HF1
NORMAL_A_OUT
NORMAL_A_IN
GND
FROM/TO Y/C/AUDIO/HEAD AMP
IIC_DATA
IIC_CLK
HIFI_H.SW
HIFI_ENV.DET
HIFI_REC_MUTE
GND
AT+12V
FROM/TO VCR SYSCON
7
P.CON+5V
8
FROM REGULATOR
8
7
C724
2.7K
50V 1 KA
C727
DEC_A-R
22
20
21
NORMAL_A_IN
4.6
19
18
17
16
15
14
13
C731
DEC_A-L
6.1
16V 10 KA
HIFI_A_OUT-R
0
4
C729
6.1
C728
16V 10 KA
HIFI_A_OUT-L
6.1 16V 10 KA
0
NC
0
NC
3.9
NC
0
3
180K
180K
R701
R713
16V 10 KA
16V 10 KA C725
R710
47K
R712
C722
50V 1 KA C721
C730
10
11
3.9 3.9
47K
9
3.9
50V 1 KA
3.9
12
M
REC
mute
50V 1 KA
2
FRONT_A_IN-R
TUNER_AUDIO-R
TUNER_AUDIO-L
TU_A_OUT
3.9
8
R720
R714
TUNER_AUDIO-L
7
R721
3.9
3.8 NC3.8
NC
TUNER_AUDIO-R
16V 10 KA
C723
6.3V
R709
16V 10 KA
TULSAP
M
TUR
nomal
E2L
select
E2R
M
6
SWD_A-L
3.8
5
C716
W836
3.8 NC 3.8
HI-FI/AUDIO/
CANAL SW IC
IC701
TDA9605H
4
auto
mute
MUTE
E2L E2R
E1R
3
line select
FRONT_A_IN-L
36
C718
39K +-1%
M
TUR
2
10K
TUL
DCR
INPUT
SELECT
SAP
1
W845
Dub
+ +
vol.
right
+
park
hold
E2R
DCL
DCR vol.
L Dub left
DCL
NORMAL_A_OUT
3.8
6.1 16V 10 KA
+
10K
34
35
A env.select(pb)
park
hold
E2L
+
M
W846
IIC_CLK
2
+
L
R
N
+
compressor CCA 32pin
expandor
33pin
RM
HID
Hifi detector
AUTN DOC
AUNToutput
select
SWD_A-R
4.2
47 KA
C720
KA
2.2
50V
R708
2.7K
R707
C713
16V 10 KA
C711
C709
0.1 F
0.1 F
37
38
39
40
41
16
I 2C
rectifier
5th order
audio LPF W+FM detector
W835
B
W834
0.1
1.3
0.1 F
HIFI_ENV.DET
IIC_DATA
4.8
NC
C816
B
noise
suppr.
47K
4.8
4.8
NC
C701
TP701
CCO
24pin
23pin
DVD_A_OUT-L
0
NC
compressor CCA
expandor
audio
clipper
10K
0
1.7MHz
1.8MHz
L
R
47K
R718
NC
1.2
rectifier
5th order
audio LPF W+FM detector
audio
clipper
47K
R717
4.8
R702
HIFI_REC_MUTE
noise
suppr.
47K
R716
0
W832
C815
0.1
4.8
0.9
HIFI_H.SW
PLL
HF LPF
R715
0
W831
0
4.9
level
detector
HF
limiter
50V 1 KA
11
47 KA
CCO
C719
10
0
100uH 0305
100CT02401
W903
6.3V
470
PLL
10K
NICAM
9
W902
X801
3.6
0.01 B
carrier ratio
record-mute
BPF
1.7MHz
1.8MHz
decoder
select
TUL
+1db 12V
E1L
SAP
TUR
E1R
M
SAP
1.3MHz
1.4MHz
HF LPF
M+
HID
0
level
detector
HF
1.3MHz
limiter
1.4MHz
50V 1 KA C717
TP2
8
L701
R705
RM
M
A
R719
NC
7
0.1 F
C703
8.2K
C705
record current
C726
Supply
10K
VSSD2
6
C702
Iref
DVD_A_OUT-R
VDDD1
5
HF2
0.6
HF AGC
R814
W840
4.7
0.6
33K
0 0.8 3.9 3.9 3.9
27
26
25
24
23
BPF
B
2.3
0
HF_COM
HID
42
22
21
20
18
W839
0.6
Vref
5
R711
E1L
VSSD1
4
4.8
220 YK
16V
C708
C809
VSSA1
3
TP1
VDDA1
2
W830
0.3
50V 2.2 KA C812
0.01 B
C810
0.01 B
C808
2.4
PCLK
50V 2.2 KA
1
ADDR1
W829
OUTL
VSSA4
NICAM IC
IC801
TDA9874AH
C807
0
0.1
HF1
playback
amplification
43
OUTM
15
XTALO
14
P2
13
XTALI
12
VREF2
44
W828
4.8
NC
0
TP3
OUTR
0
NC
EXTIL
41
2.4
6.3V 47 KA
W838
active s-by
passive s-by
100uH 0305
C835
4.8
3.0
40
2.4
NC
C801
IREF
TEST2
17
2.4
NC
11.6
44
38
39
EXTIR
ADDR2
L702
W837
0
3.8 3.9 3.9 0.8 3.9
3.8
33
32
31
30
29
28
C710
37
P1
MONOIN
6.3V 47 KA
C824
47P CH
SIF2
VREF1
SIF1
CRESET
VSSA3
VDDA3
SDA
SCL
VSSA2
42
50V 1 KA
3
TEST1
VDEC
VSSD3
0
2.4
43
4
VDDD3
0
0
NC
C802
0 4.8 2.4 2.4 2.4
27
26
25
24
23
19
B
36
0.1
SDO
SYSCLK
35
C804
WS
SCK
34
0
NC
4.8
R706
33K
NC
NC
NC
4.8 4.8 2.5 1.2 1.3 4.8
33
32
31
30
29
28
W826
C822
0.1 B
W827
0.01 B
C821
50V 1 KA
W868
C837
5
22uH 0305
C715
SIF_OUT
L802
16V 10 KA
C825
47P SL
6.3V 47 KA
IIC_CLK
C714
W844
C712
IIC_DATA
0.0068 B
6
W843
0.0068 B
6
PCB010
VMA252
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
A
H-39
B
C
D
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
F
1
G
H
H-40
A
B
C
D
E
F
G
H
DVD IN/OUT SCHEMATIC DIAGRAM
(VCR PCB)
8
8
(SD-22VB, SD-22VE)
7
7
FROM/TO AUDIO/VIDEO
TO TUNER/JACK
CP8001 (CD8501)
A2001WV2-13P
6
1
TX
2
RX
3
GND
4
GND
5
P.CON+9V
6
P.CON+9V
7
P.CON+D5V
8
P.CON+D5V
9
GND
10
P.CON+3.3V
11
P.CON+3.3V
12
GND
13
SPDIF-134
TX
B8005
DVD_G
DVD_B
W803
P.CON+9V
Y_OUT
W4BRH3.5X6X1
C_OUT
6
DVD_A_OUT-L
P.CON+5V_DH
DVD_A_OUT-R
C8117
0.01
DVD_V_OUT
F
P.CON+3.3V
W850
FROM/TO SUB MICON/OSD/VPS
RX
TX
SPDIF-134
SPDIF-134
C8084
16V 100 YK
C8085
FROM VCR SYSCON
6.3V
5
DVD_R
RX
W851
470 YK
DVD_RESET
FROM/TO AUDIO/VIDEO
5
ZERO
17
ZERO_MUTE
4.7K
50V 2.2
100K
5
6.1
NC
FFC
CD8002 2H0I1801
R8054
R8056
10K
10K
C8093
6
6.2
C8090
820P CH
6.2
10 1/4W
R8063
12.5
R8082
MUTE SW
Q8015
KTC3875S_Y_RTK
0
C8098
W867
MUTE SW. 0
Q8012
KRC103SRTK
0
R8076
0.7
1K 1/4W
0
3.3K
12K
8
16V
R8057
18K
R8060
4.7K
22 KA
37
0
MUTE SW 0
Q8014
KTC3875S_Y_RTK
R8077
0.7
1K 1/4W
4
GND
5.1
TO FI-HI/DEMODULATOR
DVD_A_OUT-L
D8010
4.6
DVD_A_OUT-R
ZERO_MUTE
1SS133
D8009
0.0015 B
3
7
DVD_A_OUT-R
P.CON+12V
50V 2.2 KA
C8099
C8095
100P CH
1K
R8050
10V 33 KA
+
-
DVD_RESET
DVD_RESET
18
+
100K 1/4W
R8051
NA
1
C8115
AUDIO-R
16
2
AT+5.2V
50V 4.7 KA
15
4.7K 50V 2.2 NA
R8048
C8088
3
P.CON+5V_DH
1.8
36
16V 330 YK
GND
R8049
P.CON+12V
5.2
22 KA
C8101
AUDIO-L
14
C8087
16V
P.CON+3.3V
W866
0.1 F
13
4
R8047
6.2
C8100
GND
6.2
50V 2.2 KA
DVD_Y(G)
12
6.1
0
DVD_G
NJM4580M
11
10K
FROM REGULATOR
MUTE SW.
Q8013
KRA101SRTK
IC8004
GND
10K
DVD_R
AT+5.2V
P.CON+9V
C8097
AMP IC
10
R8053
R8061
DVD_V(R)
4.7K
VCC
9
18K
C8092
0.0015 B
R8055
12K
GND
R8062
C8096
8
R8059
DVD_B
R8058
DVD_U(B)
100P CH
GND
7
A_GND
6
1K
C8091
CVBS
R8052
GND
5
C8089
4
C_OUT
820P CH
C(CVBS)
150
3
Y_OUT
R8067
GND
DVD_V_OUT
Y(G)
2
C8094
4
1
DVD_A_OUT-L
DVD_MUTE
CP8002 (CP8502)
IMSA-9604S-18Z13
DVD_MUTE
1SS133
3
2
2
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
PLAYBACK VIDEO SIGNAL
RECORD LUMINANCE SIGNAL
AUDIO SIGNAL(REC)
PLAYBACK COLOR SIGNAL
PLAYBACK LUMINANCE SIGNAL
DIGITAL AUDIO SIGNAL(PB)
CAUTION: DIGITAL TRANSISTOR
CAUTION: DIGITAL TRANSISTOR
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PCB010
VMA252
1
1
A
H-41
B
C
D
E
F
G
H
H-42
A
B
C
D
E
F
G
H
DVD IN/OUT SCHEMATIC DIAGRAM
(VCR PCB)
(SD-22VL)
8
7
8
FROM/TO AUDIO/VIDEO
CP8001 (CD8501)
A2001WV2-13P
6
1
TX
2
RX
3
GND
4
GND
5
P.CON+9V
6
P.CON+9V
7
P.CON+D5V
8
P.CON+D5V
9
GND
10
P.CON+3.3V
11
P.CON+3.3V
12
13
SPDIF-134
TX
DVD_R
RX
DVD_G
W851
B8005
W803
DVD_B
P.CON+9V
Y_OUT
W4BRH3.5X6X1
C_OUT
DVD_A_OUT-L
P.CON+5V_DH
DVD_A_OUT-R
C8117
0.01
DVD_V_OUT
F
P.CON+3.3V
RX
GND
TX
SPDIF-134
SPDIF-134
C8084
C8085
6.3V
FROM SYSCON2
470 YK
DVD_RESET
FROM/TO AUDIO/VIDEO
AUDIO-R
16
ZERO
17
DVD RESET
ZERO_MUTE
4.7K
DVD_RESET
CD8001
2S0I2001
R8054
R8056
10K
10K
C8093
6
6.2
C8090
0.0015 B
820P CH
7
6.2
R8057
8
12.5
AT+5.2V
R8082
MUTE SW
Q8015
2SC2412K
0
W867
37
0.7
MUTE SW. 0
Q8012
KRC103SRTK
0
R8076
1K 1/4W
0
3.3K
GND
5.1
16V 22 KA
P.CON+5V_DH
1.8
36
C8098
R8060
18K 4.7K
DVD_A_OUT-R
P.CON+12V
R8063
12K
R8061
5
6.1
FFC
10 1/4W
C8099
50V 2.2 KA
C8095
100P CH
1K
10V 33 KA
1K
C8091
R8050
+
-
100K
NC
18
+
100K 1/4W
R8051
50V 2.2 NA
1
FROM FI-HI/DEMODULATOR
4
DVD_A_OUT-L
D8010
4.6
DVD_A_OUT-R
ZERO_MUTE
1SS133
D8009
MUTE SW 0
R8077
Q8014
2SC2412K
0.7 1K 1/4W
0
DVD_MUTE
1SS133
C8115
15
C8087
4.7K
50V 2.2 NA
R8048 C8088
5.2
MUTE SW.
Q8013
KRA101SRTK
50V 4.7 KA
GND
R8049
16V 22 KA
6.2
2
C8101
AUDIO-L
14
6.2
3
16V 330 YK
13
4
R8047
W866
0.1 F
GND
6.1
0
C8100
12
C8097
10K
DVD_G
5
P.CON+12V
AMP IC
NJM4580M
DVD Y(G)
10K
FROM REGULATOR
P.CON+3.3V
IC8004
GND
11
DVD_R
50V 2.2 KA
10
0.0015 B
R8055
VCC
DVD V(R)
R8053
AT+5.2V
P.CON+9V
4.7K
C8096
9
18K
C8092
12K
GND
R8062
DVD_B
R8058
8
R8059
A_GND
DVD U(B)
100P CH
GND
7
C8094
6
R8052
CVBS
820P CH
GND
5
C8089
4
150
C(CVBS)
3
4
Y_OUT
C_OUT
DVD_V_OUT
GND
R8067
Y(G)
2
DVD_A_OUT-L
DVD_MUTE
CP8002 (CP8502)
IMSA-9604S-18Z13
1
6
FROM/TO SUB MICON/OSD/VPS
W850
16V 100 YK
5
7
TO TUNER/JACK
3
3
2
2
CAUTION: DIGITAL TRANSISTOR
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
CAUTION: DIGITAL TRANSISTOR
PCB010
VMB252
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
1
A
H-43
B
C
D
E
F
G
H
H-44
A
B
C
D
E
F
G
H
SUB MICON/OSD/VPS SCHEMATIC DIAGRAM
(VCR PCB)
8
8
(SD-22VB, SD-22VL)
7
7
C4514
L4503
390
22uH
6.3V
47 KA
BUFFER
Q4501
KTA1504S_Y_RTK
50V 1
0
AT+5.2V
S805X S805Y
FROM Y/C/AUDIO/HEAD AMP
R4509
3.1
OSD_VIDEO
EE/VV_V_OUT
100
2FSC
2.4
R4513
TX
470
1/4W
TO OPERATION/DISPLAY
RX
R4514
EE/VV_V_OUT
10 1/4W
5
R4512
DVD_LED
R3046
SUB_CS
VCR_LED
220
3.1
3.1
0
L4507
R3048
SUB_CLK
22uH
220
SUB_DATA_IN
10K
0.1 F
5.1
P21/SOUT
9
10
0
24
P10
12
13
14
2.3
23
P11
11
2.5
22
P12
15 VDCE
AIN0/CMP0-
10 CNVSS 16 P30/INT0
P22/SIN
21
D0
AIN1/CMP0+
9 RESET
5.1
SUB_RESET
P13
1
2
P20/SCK
AIN2/CMP1-
0
5.1
P31/INT1
0
FROM/TO DVD IN/OUT
0
TX
RX
0
0
FROM/TO VCR SYSCCON
0
47
4
SUB_CS
0
SUB_RESET
0
SUB_DATA_OUT
SUB_DATA_IN
15
0
50V 4.7 YK
16
SUB_CLK
5.1
IIC_DATA
IIC_CLK
AT+5.2V
CG_DATA
KA
22P CH
C4508
22P CH
C4506
W857
39uH
100
220
5.1
D7/CNTR1
OSD_VIDEO
C4515
6.3V
1
CG_CLK
CG_CS
3
2
3
IIC_CLK
GND
2FSC
IIC_DATA
CG_DATA
CG_CS
CG_CLK
R4503
3
L4501
W856
33uH
220
C4516
2.7K
C4512
R3047
R3049
R3051
L4502
SUB_DATA_OUT
0.001 Y
R4511
33P CH
C4504
R4508
C4517_1
5.1
20
5.2
P00
19
4.9
P01
TO TUNER/JACK
0
0.1 B
4.9
P02
AIN3/CMP1+
C3039
0.2
NC
D6/CNTR0
4.7K
0
25
25 P03
X3003
1001T4R010
5.1
D5
0.01 B
2.6
4
32 D2
0
0
0
26
18
15
0
27
17
14
0
28
VDD
13
0
29
VSS
12
30
XIN
11
D4
0
3
10
0.3
4
9
VCR_LED
D3
5
8
DVD_LED
5.1
5.1
31
6
7
5.1
32
7
6
NC
4.5
16
D1
1.3
8
17
4.7K
NC
47K
C3040
0
18
R3050
5.2
CVout
19
VCOR
2.1
NC
20
Vdd3
0
CVin
21
Vss2
2.1
CVcr
Vdd1
SEPc
2.5
22
Vss3
3.0
NC
VCO IN
5.1
2.0
CPout
5.1
23
Vdd2
5
5.1
24
SIN
CS2
4
3.0
SCLK
CTRL1
3
25
CS1
X’talOUT
2
NC
SYNCldg
X’talIN
1
2.8
2.6
SYNin
NC
26
SCLK2
0
SDA
27
DOUT
2.5
SEPout
28
Vss1
0
3.8
RST
29
CDLR
5.1
Vdd1
LC74775M-9839
IC4501_1
OSD/VPS/PDC IC
30
5
R3052
SUB MICON IC
IC3005
OEC7080A
XOUT
5.6K
5.1
6
AT+5.2V
100uH
0305
0.1 F
C4511
KA
CH
C4507
10P
R4505
GND
100
C4505
R4510
50V 1 KA
10K
C4503
R4502
6
0.001 Y
C4501_1
FROM REGULATOR
L4505
2
2
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
PCB010
VMA252
1
1
A
H-45
B
C
D
E
F
G
H
H-46
A
B
C
D
E
F
G
H
SUB MICON/OSD/VPS SCHEMATIC DIAGRAM
(VCR PCB)
8
8
(SD-22VE)
7
7
FROM REGULATOR
L4505
C4514
390
22uH
6.3V 47 KA
BUFFER
Q4501
KTA1504S_Y_RTK
C4510
100uH
0305
AT+5.2V
AT+5.2V
S805X S805Y
FROM Y/C/AUDIO/HEAD AMP
OSD_VIDEO
2.2uH
0
L4504
C4507
50V 1 KA
0.1 F
C4511
100
L4503
270P CH
R4505
R4510
10P CH
EE/VV_V_OUT
3.1 R4509
100
2FSC
2.4
TX
R4507
5
TO OPERATION/DISPLAY
1.2K
EE/VV_V_OUT
SUB_CS
DVD_LED
R3046
VCR_LED
220
15
5.1
3.0
2.5
2.6
5.1
0.2
4.9
4.9
5.2
3.1
3.1
0
NC
0
L4507
SUB_CLK
22uH
R3048
220
SUB_DATA_IN
10K
C4516
0.001 Y
L4502
C4512
2.7K
0.1 F
C4515
5.1
P11
P10
P20/SCK
AIN1/CMP0+
9 RESET
P21/SOUT
9
10
0
15 VDCE
AIN0/CMP0-
10 CNVSS 16 P30/INT0
P22/SIN
11
12
13
14
2.5
2.3
24
P12
AIN2/CMP1-
23
D0
P13
D1
D7/CNTR1
5.1
SUB_RESET
0
5.1
P31/INT1
15
0
0
OSD_VIDEO
0
FROM/TO DVD IN/OUT
0
TX
RX
0
4
0
FROM/TO VCR SYSCON
0
SUB_CS
0
SUB_RESET
SUB_DATA_OUT
0
SUB_DATA_IN
SUB_CLK
16
IIC_DATA
5.1
50V 4.7 YK
AT+5.2V
KA
22P CH
C4508
22P CH
C4506
W857
100
39uH 33P CH
6.3V 47
220
AIN3/CMP1+
TO TUNER/JACK
1
3
2
IIC_CLK
CG_DATA
CG_CLK
CG_CS
3
GND
IIC_CLK
2FSC
IIC_DATA
CG_DATA
CG_CLK
CG_CS
W856
3
R4503 L4501
C4504
33uH
220
C4517_1
R4511
R3047
5.1
R3051
R4508
SUB_DATA_OUT
5.1
R3049
D6/CNTR0
22
Vss3
14
P00
21
VCO IN
13
P01
25 P03
20
CPout
12
P02
19
Vdd2
11
32 D2
4.7K
0
25
18
SIN
10
0
26
17
SCLK
9
0
27
0.1 B
CS1
8
D5
0
28
VDD
SYNCldg
7
D4
0
29
VSS
DOUT
6
0
D3
30
C3039
SCLK2
5
NC
VCR_LED
0.3
5.1
31
X3003
1001T4R010
CS2
4
5.1
5.1
4.7K
CTRL1
3
2.8
DVD_LED
R3050
X’talOUT
2
5.1
32
0
1
4.5
XOUT
5.6K
16
0.01 B
1.3
1
17
2
NC
3
0
18
4
5.2
5
19
6
2.1
7
20
8
0
47K
C3040
21
VCOR
2.1
NC
22
Vdd3
2.0
CVout
23
Vss2
5.1
X’talIN
24
CVin
NC
3.0
25
CVcr
2.6
SEPout
26
Vdd1
NC
SYNin
0
SDA
27
SEPc
2.5
CDLR
28
Vss1
0
3.8
RST
29
Vdd1
OSD/VPS/PDC IC
IC4501_1
LC74775M-9839
4
5.1
R3052
SUB MICON IC
IC3005
OEC7080A
XIN
R4512
30
5
RX
R4514
10 1/4W
5.1
6
GND
C4505
50V 1 KA
10K
C4503
R4502
0.001 Y
C4501_1
6
2
2
PCB010
VMB252
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
1
A
H-47
B
C
D
E
F
G
H
H-48
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM
(POWER PCB)
(SD-22VB)
8
R533
D526
D503
W4BRH3.5X6X1.0X2
UNREG+3.3V
7
AT+5.2V
6
AT+5.2V
5
AT+13V
4
MOTOR GND
3
MOTOR+12V
2
6
WIRE
CD502 2Y0G1701
1
R518
220 YK
390 1/4W
5.1
11.3
4
W808
R509
P.CON5V SW
Q505
KTC3209_Y
5.2
R513 5.8
C530
0
C520
0.1
C514_2
P.CON SW
Q506
KRC101MAT
C527
2
P.CON +B SW
Q504
KTA1241_Y
12.0
11.9
16V 100 YK
C501
1
4
W805
CP503 (CD8502)
A2001WV2-6P
1K 1/4W
R521
VOLTAGE CTL IC
IC501
KIA431
B
330 1/4W
C524
0.1
GND
GND
IN
2
1
0
2.5
R522
2.3
+-1%
2
P.CON+5V_A
3
GND
4
P.CON+9V_A
5
MOTOR_GND 6
6.3V 1000 YK
2
+-1%
3
1
GND
3.3K
OUT
MOTOR_GND
P.CON+5V_D
3.3K
R520
C517
2
3
TO AUDIO/VIDEO
R519
820 1/4W
8
5.1
150 1/4W
C528
16V 100 YK
R525
M
10K 1/4W
MTZJ15B
9
UNREG+3.3V
0.4
HS502
763WAA0186
D531
R507
C508_1
0.0082
3.3
2.3
3
D530
10ELS6N
D524
1SS133
820 1/4W
R524
R508
16.4
3.8
10K 1/4W
D510
MTZJ22B
1W
R502
1.5
PROTECT CONTROL
Q502
0.5 KTC3203_Y
3.8
OUT
3
9.0
22uH
TSL0808
SB290S
10ELS6N
PHOTO COUPLER
IC503
LTV-817M-VB
GND
2
0
10K 1/4W
D522
W811
12.4
R510
0
4
NC
6.3V
D507
20
IN
1
L503
470 1/2W
0.018 M
10
POWER ON H
NC
10V 330 YK
19 NC
W814
D529
SB290S
0
C510
C509
11
GND
F
R517_2
25V 470 YK
142.0
12
GND
9V REG. IC
IC502_1
KIA7809API
22uH
0305
18
13
P.FAIL
680 1/2W
L505
0.22 1W
R516
C525_1
2KV 220P RR
NC 3
14
5
MTZJ33B
0
17
15
D523
0
4
C529
15
6.3V 1000
YK
6
C505_1
0
14
D525
16V 220 YK
7
0
2
0
L506
1N4005-EIC
50V 10 KA
13
25V 2200 YK
R506
470K 1/2W
8
10V 3300 YK
0
0
HS501
763WSA0016
C519_1
12
0
16
560 1W
-22V
22uH TSL0808
SB340L-6737
-18.9
139.3
R504
HEATER_DC -
11
38
39
1K 1/4W
10ELS6N
KX
-18.9
0
SWITCHING
Q501
151.0
D
2SK2647-01MR
G
0.5
S 0.1
HEATER_DC + 16
R536
D512
0
5
D518_1
C518
B501
R505
560K 1/4W
250V 0.0047
T501
8129102S
NC 9
3
B503
W4BRH3.5X6X1
C516
RM11C-EIC
6.3V 2200 YK
500V 0.01 E
D509_1
C513_1
4
COIL,LINE FILTER
L501
0R3A433F20
CP502 (CP1701_1)
B2013H02-16P
TUNER+32V
D505
4A 125V
FROM/TO REGLATOR
22uH TSL0808
C522
3
1KV 220P B
C511_1
PHE840
RM11C-EIC
2
7
L507
D515
SB340L-6737
W802
6
1
400V 100 PK
FH502
EYF-52BC
D502
275V 0.1
FH501
EYF-52BC
C502_1
F501
T4A_L_250V
W804
RGP10K-EIC
R512
82K 2W
C515
RM11C-EIC
MTZJ24B
D506
1
1
R531_2
680 1/2W
C521
7
D521
10ELS2N
RM11C-EIC
2
BROWN
CP501
A3963WV2-3PD
2
BLUE
10ELS2N
50V 10 YK
AC230-240V_50Hz
CD501_6
0G639803
D532
1/4W
10V 330
YK
1.8
C523
8
PCB240
4A 125V
VPA152
1
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE 4A 125V(F501).
ATTENTION:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE
N’UTOLISER QUE DES FUSIBLE DE MEME TYPE 4A 125V(F501).
A
H-49
B
CAUTION: DIGITAL TRANSISTOR
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
C
ARE
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
D
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
1
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
F
G
H
H-50
A
B
C
D
E
F
G
H
POWER SCHEMATIC DIAGRAM
(POWER PCB)
(SD-22VE, SD-22VL)
R533
10ELS2N
S502_1
R531_2
D521
C521
7
FROM/TO REGLATOR
7
0
14
6
15
0
1000
YK
F
C520
0.1
10
UNREG+3.3V
8
UNREG+3.3V
7
AT+5.2V
6
AT+5.2V
5
AT+13V
4
MOTOR_GND
3
MOTOR+12V
2
MOTOR+24V
1
6
WIRE
CD502 2Y0G1701
5
0
9.0
12.0
16V 220 YK
C505_1
R510
C514_2
16V 100 YK
P.CON SW
Q506
KRC101MAT
C527
W814
C510
25V 470 YK
4
5.1
3
10V 330 YK
500V 470P B
390 1/4W
11.3
5.1
0
HS502
763WAA0186
C506
11.9
P.CON5V SW
Q505
KTC3209_Y
5.2
R513 5.8
W808
12.4
P.CON +B SW
Q504
KTA1241_Y
OUT
3
0.4
2
2.3
150 1/4W
25V 2200 YK
C501
R518
1
3.3
16V 100 YK
TO AUDIO/VIDEO
(CD8502)
CP503
A2001WV2-6P
UG2D
R519
1K 1/4W
B
R521
VOLTAGE CTL IC
IC501
KIA431
R520
2
OUT
GND
3
0
C517
6.3V
MOTOR_GND
P.CON+5V_D
1
GND
2
P.CON+5V_A
3
GND
4
P.CON+9V_A
5
MOTOR_GND 6
1000 YK
2
1
2.5
R522
2.3
IN
2
GND
+-1%
0.1
330 1/4W
C524
3.3K
C528
4
16.4
3
D530
10ELS6N
D524
1SS133
R524
10K 1/4W
R525
10K 1/4W
C508_1
0.0082 M
R507
820 1/4W
MTZJ22B
D510
1W
R502
1.5
PHOTO COUPLER
IC503
LTV-817M-VB
D508
W805
W811
GND
2
22uH
TSL0808
SB290S
10ELS6N
MTZJ15B
820 1/4W
L503
D507
D522
IN
1
R509
19
3.8
NC
R508
C530
D529
SB290S
0
20
0
11
GND
9V REG.IC
IC502_1
KIA7809API
470 1/2W 10K 1/4W
18
R517_2
0
D531
12
GND
680 1/2W
L505
NC 3
0.018 M
PROTECT CONTROL
Q502
0.5 KTC3203_Y
3.8
1N4005-EIC
22uH
0305
17
50V 10 KA
MTZJ33B
C507
1W
13
P.FAIL
D523
0
4
142.0
C509
14
0
2
560
15
6.3V
13
D525
C529
8
C522
470K 1/2W
R506
G
0.5
S 0.1
2200 YK
0
0
HS501
763WSA0016
3
C518
12
10V 3300 YK
NC 9
139.3
R504
L506
22uH TSL0808
-18.9
0
16
39
16
HEATER -22V
11
0.22 1W
R516
C525_1
2KV 220P RR
4
D
SB340L-6737
-18.9
0
SWITCHING
Q501
2SK2647-01MR
HEATER +
POWER_ON_H 9
1K 1/4W
D512
38
151.0
CP502
(CP1701_1)
B2013H02-16P
R536
10ELS6N
T501
8129102S
0
5
D518_1
250V 0.0047 KX
W4BRH3.5X6X1.0X2
R505
B501
RM11C-EIC
6.3V
C519_1
500V 0.01 E
D509_1
1KV 220P B
C516
D505
COIL,LINE FILTER
L501
0R3A433F20
B503
W4BRH3.5X6X1
50V 330 YK
RM11C-EIC
4
C513_1
D502
22uH
TSL0808
TUNER+32V
W802
3
C511_1
2
400V 100 PK
1
560K 1/4W
FH502
EYF-52BC
C502_1
FH501
EYF-52BC
275V 0.1 PHE840
F501
50T040H
RGP10K-EIC
4A 125V
82K 2W
C515
SB340L-6737
R512
RM11C-EIC
6
L507
D515
W804
7
6.3V 220 YK
D503
680 1/2W
50V 10 YK
10ELS2N
D526
RM11C-EIC
MTZJ24B
D506
S501_1
BROWN
+-1%
BLUE
330
YK
D532
1/4W
C523
1.8
3.3K
AC230V_50Hz
CD501_2
06459801
8
10V
8
PCB240
VPA152
4A 125V
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
CAUTION:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE FUSE 4A 125V(F501).
1
ARE
ATTENTION:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIE
N’UTOLISER QUE DES FUSIBLE DE MEME TYPE 4A 125V(F501).
A
H-51
B
C
CAUTION: DIGITAL TRANSISTOR
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
D
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
F
1
G
H
H-52
A
B
C
D
E
F
G
H
DISPLAY SCHEMATIC DIAGRAM
(DISPLAY PCB)
8
V601
HNV-09SS33
8G
9G
7G
SLP
HQ
7
2
6G
4
5
6
5G
2G
3G
4G
1G
C
VCR
1
8
CH
7
8
M
9 10 11 12
S PM
24 25 26 27 28 29 30 31 32
7
34 35
HEATER_DC+
8.2 1/2W
P9
P8
P7
P6
P5
P4
P3
P2
P1
9G
8G
7G
6G
5G
4G
3G
2G
1G
R603
HEATER_DCD601
MTZJ5.1C
-22V
25
26
0
4.9
27
0
28
FRONT_V_IN
G5
VDD
G4
G3
R605
R604
C609
0.1 F
R602
0
100K 1/4W
6.3V 100 KA
C608
2.5
R601
0
RESET
Q601
KTC3198
1K 1/4W
AT+5.2V
1/4W
4
FL_DATA
FL_CLK
FL_CS
4
0.1 F
C607
R611
10
75 1/4W
0.001 B
0.001 B
C615_1
16V 10 KA
C614_1
47K 1/4W
8G
29
30
31
32
0 -20.5 -20.5
4.9
2.5
C604
NC
VSS
OSC
SO
SI
VSS
SCK
22
23
24
0
0.3
5.0
FIP DRIVER IC
IC601
BU2977FS
G6
G7
G8
G9
S16/G11
S15/G12
S14/G13
S13/G14
S10
VEE
CS
21
0
K1
K2
20
0
5
0.001 B
2
H
1
19
0
FRONT_A_IN-L
C616
E
18
4.9
K3
2
-18.0
FRONT VIDEO IN
J601 AV1-06DG-1
K4
17
H
1
E
FRONT_A_IN-R
9G
1G
2G
3G
4G
5G
6G
7G
P2
P3
P4
P5
S9
P6
P7
2
NC
1
3
E
FRONT AUDIO IN L
J602 AV1-06DG-1
5
6
-8.5
-6.3 -20.4 -20.3 -20.4 -20.4 -20.4
0 -16.7 -22.0
-9.2 -14.5
12
11
10
2
1
9
8
7
6
5
4
3
H
S6
-12.8 -10.9
-4.9
16
15
14
13
S8
-19.4
FRONT AUDIO IN R
J603 AV1-06DSG-1
P8
P9
P1
6
AT+5.2V
REM_IN
KEY-A
KEY-B
FROM/TO DISPLAY
CP601
52492-1820
FRONT_V_IN
FRONT_V_IN 18
GND
FRONT_A_IN-L
3
GND
GND 3
100 1/4W
5.0
GND
13
KEY-A
12
KEY-B
11
NC
0
SKQNAED010
CH DOWN
SW605
SKQNAED010
CH UP
SW604
SKQNAED010
KEY-B
10
REM_IN
REM_IN
9
AT+5.2V
8
GND
7
FL_CLK
6
FL_DATA
5
FL_CS
4
HEATER_DC+
3
HEATER_DC-
2
-22V
1
AT+5.2V
100 KA
B+ 2
1.5K 1/4W
VCR/DVD(HDD)
CS
SW603
1
2
FL_CLK
FL_DATA
FL_CS
HEATER_DC+
HEATER_DC-
3
15
FRONT_A_IN_R 14
KEY-A
6.3V
R608
1.8K 1/4W
SKQNAED010
1/4W
POWER
SW602
SKQNAED010
VCR EJECT
SW601
2.7K
R607
C613
Vout
R606
5.1
R610
FRONT_A_IN-R
OS601
PIC-37143TH5
17
FRONT_A_IN_L 16
-22V
2
PCB390
VEA972
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
1
A
H-53
B
C
RECORD COLOR SIGNAL
RECORD LUMINANCE SIGNAL
AUDIO SIGNAL(REC)
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
D
E
F
1
G
H
H-54
A
B
C
D
E
F
G
H
OPERATION SCHEMATIC DIAGRAM
8
8
7
7
(OPERATION1 PCB)
(OPERATION2 PCB)
SKQNAED010
6
OPEN/CLOSE
SW689
6
GND
S681Y
S681X
WIRE RED
KEY B
S682Y
S682X
WIRE BLUE
5
5
PCB280
VEA979
R685
R687
R688
2.7K 1/4W
STOP
SW688
R694
3.3K 1/4W
SKQNAED010
1/4W
SKQNAED010
3.9K
SKQNAED010
FF/CUE
SW684
6.8K 1/4W
SKQNAED010
PLAY
SW682
SKQNAED010
REW/REV
SW681
4
R683
1/4W
REC/OTR
SW686
R681
13K
330 1/4W
R690
LTL-1CHGE-002A
4
DVD LED
D681_1
LTL-1CHGE-002A
SKQNAED010
DVD/VCR
SW687
330 1/4W
VCR LED
D685_1
FROM/TO DISPLAY
CP681
52492-0720
R686
NC
R689
1/4W
3
10K 1/4W
6.8K
PCB270
VEA978
7
VCR_LED
6
DVD_LED
5
GND
4
AT+5.2V
3
KEY-A
2
KEY-B
1
3
2
2
NOTE:THE DC VOLTAGE EACH PART WAS
MEASURED WITH THE DIGITAL TESTER
DURING PLAYBACK.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
1
1
A
H-55
B
C
D
E
F
G
H
H-56
D
E
F
INTERCONNECTION DIAGRAM
4
RF
22
RF
P.CON+9V
5
5
GND
P.CON+9V
VCC
23
VCC
P.CON+9V
6
6
P.CON+9V
P.CON+D5V
7
7
P.CON+D5V
P.CON+D5V
8
8
P.CON+D5V
GND
9
9
GND
TGL5
2
2
2
TGL5
P.CON+3.3V
10
10
P.CON+3.3V
LDMN
3
3
3
LDMN
P.CON+3.3V
11
11
P.CON+3.3V
TOPN
4
4
4
TOPN
LDMP
5
5
5
LDMP
M_GND
6
6
6
M_GND
3
DMP
4
4
DMN
LMT
5
5
5
LMT
GND
6
6
6
GND
FMP
7
7
7
FMP
FMN
8
8
8
FMN
MOTOR GND
GND
P.CON+9V A
GND
P.CON+5V D
P.CON+5V A
2
GND
3
3
C(CVBS)
GND
15
15
4
4
GND
CVBS
14
14
5
5
CVBS
GND
13
13
6
6
GND
12
12
7
7
DVD_U(B)
11
11
8
8
GND
10
10
9
9
DVD_V(R)
9
9
10
10
GND
8
8
11
11
DVD_Y(G)
GND
7
7
12
12
GND
AUDIO-L
6
6
13
13
AUDIO-L
GND
5
5
14
14
GND
AUDIO-R
4
4
15
15
AUDIO-R
ZERO
3
3
16
16
ZERO
DVD_RESET 2
2
17
17
DVD_RESET
1
1
18
20 SW2
NC
19 SW1
NC
18 NC
NC
CYL_CTL
12
CP101
15 NC
9
9
8
8
8
HF2 (L)
7
7
7
SP-CH1 (R)
6
6
6
5
5
5
SP-CH2 (L)
4
4
4
EP/LP-CH1 (R)
3
3
3
2
2
2
1
1
1
5
5
5
5
AT+5.2V
AT+13V
4
MB
3
SDA
DEC.A.OUT(R)
DECORDER/PERITEL
J8005
5 SCL
AT+13V
4
4
4
4
MOTOR_GND 3
3
3
3
MOTOR_GND
MOTOR+12V
2
2
2
2
MOTOR+12V
MOTOR+24V
1
1
1
1
MOTOR+24V
2
A.IN
1 BB
25
24
2
1
A.OUT(R)
25
23
22
27
26
4
3
6
5
7
D
33
32
30
8
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
C
31
29
28
10
9
35
34
12
11
37
36
14
39
38
16
13
15
DEC.VIDEO IN
AT+5.2V
AT+5.2V
41
40
18
17
42
VCR PCB
PCB010
VMB252
20
19
CD102
FFC
CP102
GND
UNREG+3.3V
6
SP HEAD
3
HEAD AUDIO CONTROL ASS’Y
H5001
AUDIO_PB
6
6
AUDIO_PB
AUDIO_REC
5
5
AUDIO_REC
CTL+
4
4
CTL+
CTL-
CTL-
3
3
AE_HEAD(+)
2
2
AE_HEAD(-)
AE_HEAD(-)
1
1
AE_HEAD(+)
AUDIO
2
CONTROL
AE
21
GND
7
6
DEC.VIDEO OUT
7
6
VIDEO IN
7
6
GND
7
AT+5.2V
GND
UNREG+3.3V
6 V.IN
VIDEO OUT
UNREG+3.3V
NC
8
GND
8
GND
8
NC
8
DVD RGB H
UNREG+3.3V
7 TU(MD)
GND
GND
POWER_ON_H
GND
9
DVD_R
9
NC
9
GND
POWER_ON_H 9
GND
GND
10
NC
11
10
NC
11
10
DVD_G
11
10
PERI CTL_L
11
GND
8 AGC
NC
GND
NC
GND
P.FAIL
NC
12
GND
13
12
TV-L/VCR-H
13
12
DEC.A.IN(L)
13
12
HI-FI HEAD
EP/LP HEAD
NC
TUNER+32V
13
P.FAIL
9 NC
DVD_B
TUNER+32V
NC
GND
-22V
A.IN(L)
14
GND
14
GND
14
GND
14
DEC.A.OUT(L)
HEATER-
-22V
A.OUT(L)
HEATER+
15
EP/LP-CH2 (L)
10 AS
DEC.A.IN(R)
16
15
EP/LP_COM
A.IN(R)
16
15
ARE
FPC
9
HF1 (R)
HF_COM
CP1701_1
16
G
16 TU
SP_COM
15
LOADING MOTOR
M101
4
13 PB
16
WHITE
CYLINDER UNIT ASS’Y
UN4001
14 +B
HEATER-
5
LM
17 NC
NC
HEATER+
O
VCC
2
FE_HEAD (HOT)
2
H5002
KEY-B
AT+5.2V
GND
DVD_LED
VCR_LED
CP103
2
1
KEY-B
3
KEY-A
4
AT+5.2V
CP681
CD651
FFC
5
18
1
GND
17
2
GND
FRONT_V_IN
6
GND
FRONT_V_IN
16
3
GND
FRONT_A_IN_L
DVD_LED
GND
FRONT_A_IN_L
15
4
7
GND
FRONT_A_IN_R
14
5
FRONT_A_IN_R
VCR_LED
KEY-A
KEY-A
KEY-B
REM_IN
AT+5.2V
GND
GND
NC
18
CD502
FFC
6
MOTOR_GND
5
4
GND
P.CON+9V_A
3
P.CON+5V_A
12
CAPSTAN DD UNIT ASS’Y
M2001
RED
6
5
4
3
2
2
GND
1
CP503
P.CON+5V_D
11
7
2
16
GND
CP501
1
1
CYL_FG/PG
6
17
16
2
2
11
21 A.OUT
17
GND
B
10
5
GND
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
A
H-57
LDM_CTL
22 SIF
26
1
9
10
Y(G)
C(CVBS)
CP502
BROWN
CAP_CTL
4
1
DVD_V(R)
POWER PCB
PCB240
VPA152
9
3
1
11 SCL
BLUE
8
LD/CY_VCO
1
18
RGB-H
1
CD8502
FFC
18
12 SDA
AC230-240V_50Hz
CD501_6
0G639803
7
8
23 AFT
CP8002
Y(G)
DVD_Y(G)
2
GND
CD8002
DVD_U(B)
3
6
7
7
3
4
MOTOR_GND
D-U_OUT
3
DMN
5
6
6
DMP
I_LIMIT
D-V_OUT
VCC
4
5
5
2
CAP/M/F/R
D-W_OUT
2
3
4
4
2
VCC
D-COM
VCC
2
3
3
DMFG
1
CAP_VCO
M-GND
1
24 V.OUT
CAP_FG
2
FFC
CP2601
1
SPDIF-134
27
1
2
1
13
TU301
28
6
CP3001
1
DMFG
CD2601
FFC
GND
3
2
13
L8507
12
OUT
HALL HALL
SWITCH
VCC
IN
LOGIC
7
4
VCC
1 INPUT
H2 H1
MR
FG SENSOR
ROTOR
MAGNET
6
GND
2
GND
2
5
LD2
3
H
3
MAIN
COIL
4
21
2
1
1
3
LD2
SPDIF-134
2
OPT TRNSFORMER
OS8001
2
GND
E
HALL
SENSOR
7
3
6
3
AUDIO OUT
J8002
COAXIAL
J8001
E
1
5
4
5
GND
7
FULL ERASE HEAD ASS’Y
6
4
MDN2
TX
3
20
12
S682X
Y/C SEPA
J8003
2
RX
MDN2
GND
FL_CLK
FL_CS
2
1
FL_DATA
HEATER_DC-
1
2
1
13
1
18
1
RX
CP2603
KEY B
WIRE BLUE
S681X
KEY-A
B+ 3
1
GND 2
OS601
TX
VDR2
CP8502
4
Vout
CP601
GND
19
CD2603
FFC
S682Y
CP8001
18
8
1
SLED MOTOR
CD8501
GND
1
5
DVD PCB
PCB130
VMA249
VDR2
SPINDLE MOTOR
6
VREF
KEY-B
17
12
VREF
11
VCC
7
16
8
VCC
REM_IN
F0
9
E0
15
10
14
F0
9
E0
S681Y
GND
WIRE RED
10
A0
GND
13
AT+5.2V
D0
A0
8
12
11
C0
D0
7
B0
11
6
10
C0
12
B0
13
F+
FL_CS
9
5
T-
F+
4
8
14
T+
T-
15
F-
7
HEATER_DC+
6
T+
HEATER_DC-
F-
3
VCC
2
5
17
VCC
H
FRONT AUDIO IN R
J603
OPERATION1 PCB
PCB270
VEA978
HEATER_DC+ 16
GND
-22V
4
2
DISPLAY PCB
PCB390
VEA972
D-PG_OUT
LM
LD
GND
FRONT AUDIO IN L
J602
NC
(SD-22VB)
D-PG_GND
LOADING MOTOR
3
3
2
1
1
6
MDN
LD
-22V
OPTICAL PICK-UP
VDR
2
E
1
CD652
FFC
DVD
DRIVE
1
MDN
H
FRONT VIDEO IN
J601
CP651
7
VDR
2
FL_CLK
COMMAND TRANSMITTER
TM601
H
CP2602
E
1
H
OPERASTION2 PCB
PCB280
VEA979
CP653
E
FL_DATA
8
G
1
C
FE_HEAD (GND)
B
1
A
1
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
F
G
H
H-58
D
E
F
INTERCONNECTION DIAGRAM
4
4
RF
22
RF
P.CON+9V
5
5
GND
P.CON+9V
VCC
23
VCC
P.CON+9V
6
6
P.CON+9V
P.CON+D5V
7
7
P.CON+D5V
P.CON+D5V
8
8
P.CON+D5V
GND
9
9
GND
TGL5
2
2
2
TGL5
P.CON+3.3V
10
10
P.CON+3.3V
LDMN
3
3
3
LDMN
P.CON+3.3V
11
11
P.CON+3.3V
TOPN
4
4
4
TOPN
LDMP
5
5
5
LDMP
M_GND
6
6
6
M_GND
3
DMP
4
4
DMN
LMT
5
5
5
LMT
GND
6
6
6
GND
FMP
7
7
7
FMP
FMN
8
8
8
FMN
MOTOR GND
GND
P.CON+9V A
GND
P.CON+5V A
P.CON+5V D
17
2
2
GND
16
16
3
3
C(CVBS)
GND
15
15
4
4
GND
CVBS
14
14
5
5
CVBS
GND
13
13
6
6
GND
12
12
7
7
DVD_U(B)
11
11
8
8
GND
10
10
9
9
DVD_V(R)
9
9
10
10
GND
8
8
11
11
DVD_Y(G)
GND
7
7
12
12
GND
AUDIO-L
6
6
13
13
AUDIO-L
GND
5
5
14
14
GND
AUDIO-R
4
4
15
15
AUDIO-R
ZERO
3
3
16
16
ZERO
DVD_RESET 2
2
17
17
DVD_RESET
1
1
18
1
2
3
1
KEY-B
AT+5.2V
GND
DVD_LED
NC
19 SW1
NC
18 NC
NC
17 NC
CYL_CTL
12
CP101
15 NC
9
9
8
8
8
HF2 (L)
7
7
7
SP-CH1 (R)
6
6
6
HF_COM
14 +B
CP1701_1
5
5
5
SP-CH2 (L)
4
4
4
EP/LP-CH1 (R)
3
3
3
2
2
2
1
1
1
AT+5.2V
AT+5.2V
5
5
5
5
AT+5.2V
AT+13V
4
4
4
4
MOTOR_GND 3
3
3
3
MOTOR_GND
MOTOR+12V
2
2
2
2
MOTOR+12V
MOTOR+24V
1
1
1
1
MOTOR+24V
5 SCL
4
MB
3
SDA
AT+13V
2
A.IN
25
CAUTION: SINCE THESE PARTS MARKED BY
CRITICAL FOR SAFETY,USE ONES
DESCRIBED IN PARTS LIST ONLY
ARE
25
24
2
1
A.OUT(R)
26
23
22
27
26
4
3
6
5
7
D
33
32
30
8
ATTENTION: LES PIECES REPAREES PAR UN
ETANT
DANGEREUSES AN POINT DE VUE SECURITE
N’UTILISER QUE CELLS DECRITES
DANS LA NOMENCLATURE DES PIECES
C
31
29
28
10
35
34
12
9
11
37
36
14
13
39
38
16
15
DEC.VIDEO IN
UNREG+3.3V
6
41
40
18
17
42
VCR PCB
PCB010
VMB252
20
19
CD102
FFC
CP102
GND
7
6
G
HI-FI HEAD
SP HEAD
3
HEAD AUDIO CONTROL ASS’Y
H5001
AUDIO_PB
6
6
AUDIO_PB
AUDIO_REC
5
5
AUDIO_REC
CTL+
4
4
CTL+
CTL-
3
3
AE_HEAD(+)
2
2
AE_HEAD(-)
AE_HEAD(-)
1
1
AE_HEAD(+)
CTL-
AUDIO
2
CONTROL
AE
21
GND
7
6
DEC.VIDEO OUT
7
6
VIDEO IN
7
AT+5.2V
GND
UNREG+3.3V
6 V.IN
VIDEO OUT
UNREG+3.3V
GND
8
GND
8
NC
8
GND
8
NC
UNREG+3.3V
7 TU(MD)
GND
DVD RGB H
POWER_ON_H
GND
9
DVD_R
9
GND
9
GND
POWER_ON_H 9
NC
GND
10
GND
11
10
NC
11
10
NC
11
10
NC
11
GND
8 AGC
NC
GND
NC
DVD_G
P.FAIL
PERI CTL_L
12
GND
13
12
GND
13
12
TV-L/VCR-H
13
12
4
EP/LP HEAD
DEC.A.IN(L)
TUNER+32V
13
P.FAIL
9 NC
NC
TUNER+32V
NC
DVD_B
-22V
GND
14
GND
14
A.IN(L)
14
GND
14
GND
-22V
EP/LP-CH2 (L)
10 AS
DEC.A.OUT(L)
HEATER-
A.OUT(L)
HEATER+
15
DEC.A.IN(R)
16
15
A.IN(R)
16
15
EP/LP_COM
DEC.A.OUT(R)
16
15
LOADING MOTOR
M101
FPC
9
HF1 (R)
SP_COM
16
WHITE
LM
16 TU
NC
18
HEATER-
5
CYLINDER UNIT ASS’Y
UN4001
13 PB
HEATER+
O
2
FE_HEAD (HOT)
2
VCC
1
H5002
KEY-B
KEY-A
CP681
CD651
FFC
4
18
1
FRONT_V_IN
AT+5.2V
17
2
5
16
3
GND
GND
FRONT_V_IN
15
4
GND
GND
FRONT_A_IN_L
6
GND
FRONT_A_IN_L
14
5
GND
DVD_LED
GND
FRONT_A_IN_R
13
6
7
KEY-A
12
KEY-A
VCR_LED
KEY-B
11
7
REM_IN
8
20 SW2
DECORDER/PERITEL
J8005
CD502
FFC
6
MOTOR_GND
5
4
GND
P.CON+9V_A
3
P.CON+5V_A
12
CAPSTAN DD UNIT ASS’Y
M2001
21 A.OUT
NC
6
5
4
3
1
CD8502
2
2
GND
1
CP503
P.CON+5V_D
11
7
17
GND
B
CYL_FG/PG
RED
1 BB
A
11
6
GND
C(CVBS)
CP502
H-59
10
22 SIF
11 SCL
1
LDM_CTL
Y(G)
3
BROWN
9
10
5
1
DVD_V(R)
POWER PCB
PCB240
VPA152
CAP_CTL
4
1
RGB-H
S501_1
9
3
18
12 SDA
BLUE
8
LD/CY_VCO
1
18
GND
S502_1
7
8
23 AFT
CP8002
FFC
Y(G)
DVD_U(B)
AC230V_50Hz
CD501_2
GND
CD8002
DVD_Y(G)
2
6
7
7
3
4
MOTOR_GND
D-U_OUT
3
DMN
5
6
6
DMP
I_LIMIT
D-V_OUT
VCC
4
5
5
2
CAP/M/F/R
D-W_OUT
2
3
4
4
2
VCC
D-COM
VCC
2
3
3
DMFG
1
CAP_VCO
M-GND
1
24 V.OUT
CAP_FG
2
FFC
CP2601
1
SPDIF-134
27
1
2
1
13
TU301
28
6
CP3001
1
DMFG
CD2601
FFC
GND
3
2
L8507
12
OUT
HALL HALL
SWITCH
VCC
IN
LOGIC
7
GND
VCC
1 INPUT
H2 H1
MR
FG SENSOR
ROTOR
MAGNET
6
LD2
2
GND
2
5
21
3
H
3
MAIN
COIL
4
LD2
2
1
1
3
GND
13
2
OPT TRNSFORMER
OS8001
2
3
E
HALL
SENSOR
7
3
6
GND
AUDIO OUT
J8002
COAXIAL
J8001
E
1
5
4
5
MDN2
SPDIF-134
6
4
20
TX
3
RX
MDN2
12
FULL ERASE HEAD ASS’Y
Y/C SEPA
J8003
2
2
GND
KEY-B
HEATER_DC-
1
2
1
9
1
18
1
RX
1
S682X
7
KEY-A
B+ 3
1
GND 2
OS601
TX
VDR2
CP8502
4
Vout
GND
19
CP2603
S681X
1
SLED MOTOR
CP601
18
CD2603
FFC
KEY B
WIRE BLUE
CP8001
GND
1
5
CD8501
VDR2
SPINDLE MOTOR
10
VREF
9
17
10
VREF
REM_IN
VCC
GND
16
AT+5.2V
VCC
8
F0
11
E0
15
AT+5.2V
14
F0
FL_CLK
E0
7
A0
6
13
12
D0
A0
13
12
GND
C0
D0
FL_CLK
B0
11
FL_CS
10
C0
FL_DATA
B0
5
F+
4
T-
9
14
8
F+
15
T-
DVD PCB
PCB130
VMA249
FL_CS
T+
FL_DATA
F-
7
HEATER_DC+
6
T+
HEATER_DC-
F-
3
VCC
2
5
17
VCC
S682Y
GND
WIRE RED
OPERATION1 PCB
PCB270
VEA978
HEATER_DC+ 16
GND
-22V
4
S681Y
H
FRONT AUDIO IN R
J603
D-PG_OUT
LM
LD
GND
2
8
D-PG_GND
LOADING MOTOR
3
NC
H
OPERATION2 PCB
PCB280
VEA979
DISPLAY PCB
PCB390
VEA972
FRONT_A_IN_R
6
MDN
LD
-22V
OPTICAL PICK-UP
VDR
2
3
1
CD652
FFC
DVD
DRIVE
1
MDN
CP651
7
VDR
E
1
2
2
H
H
FRONT VIDEO IN FRONT AUDIO IN L
J601
J602
COMMAND TRANSMITTER
TM601
CP2602
E
1
VCR_LED
E
CP653
8
G
(SD-22VE, SD-22VL)
FE_HEAD (GND)
C
1
B
CP103
A
1
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME
OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
E
F
G
H
H-60
WAVEFORMS
Y/C/AUDIO/HEAD AMP
REC
REC
10µs
0.5V
5µs
10V
10µs
500mV
30
6
1
PB
REC
10µs
200mV
5µs
10V
10µs
500mV
7
2
31
VCR SYSCON
POWER ON
50ns
100mV
3
PB
5ms
100mV
4
PB
200ms
10µs
500mV
1.0V
32
17
PB
200ms
500ns
100mV
1.0V
34
18
TUNER/JACK
REC, PB
5ms
1V
DVD IN/OUT
10µs
500mV
36
5
29
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
I-1
WAVEFORMS
20ns
10µs
20mV
100mV
37
52
POWERPOWER
5µs
57
MPEG
10µs
500ns
50mV
500mV
38
20mV
58
53
5µs
5.0V
10µs
20mV
20ns
100mV
39
59
54
MEMORY
READ CHANNEL
100ns
50mV
50
5ns
20mV
20ns
100mV
60
55
AUDIO/VIDEO
100ns
10µs
20ns
50mV
20mV
50mV
51
61
56
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
I-2
WAVEFORMS
500ns
50mV
62
10µs
50mV
67
500µs
10µs
50mV
50mV
63
500µs
50mV
64
10µs
50mV
65
68
10µs
50mV
69
10µs
50mV
70
SYSCON1
10µs
50mV
66
50ns
100mV
71
NOTE: The following waveforms were measured at the point of the corresponding
balloon number in the schematic diagram.
I-3