Download yright LASER Copyright LA Copyright LASER
Transcript
C op LA ht y SE C ri yr SE C o g LA ig R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R ht SE C r y S C ig op ri ER R o gh L h p y A t C ri yr t SE C ER op gh i op gh LA R y LA t C r y t S C i op ri gh SE ER o g L py yr LA ht A t S C ig op ri SE ER o g L h py yr LA ht A t R SE C ig r SE C ig op LA ht R o LA ht R y SE C ig ri SE C o g LA ht R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R ht SE C r y S C ig op ri ER R op gh L h yr A t SE C yr t SE C i o g i R op py gh LA ht R LA C r y t S C i op ri gh S ER op g L yr LA ht A t C y S C ig op ri SE ER op g L h yr LA ht A t R y SE C ig r SE C ig op LA ht R LA ht R ri yr S C gh SE C ER ig op L op LA ht A t R y SE C ri yr SE C o g LA i R op py LA ht R SE C ri yr S C o g LA ER ig R op py LA ht ht SE C r y S C i op ri gh ER R op gh L yr A t SE C yr t SE C i o g i R op py gh LA ht R C ri yr t SE C op gh i o g L R R Incorrect or out of phase engine timing can result in damage to the valves. The Tool Connection cannot be held responsible for any damage caused by using these tools in anyway. 3388 Safety Precautions – Please read LA SE R • Disconnect the battery earth leads (check radio code is available) • Remove spark or glow plugs to make the engine turn easier • Do not use cleaning fluids on belts, sprockets or rollers • Always make a note of the route of the auxiliary drive belt before removal py ri g ht • Turn the engine in the normal direction (clockwise unless stated otherwise) • Do not turn the camshaft, crankshaft or diesel injection pump once the timing chain has been removed (unless specifically stated) • Do not use the timing chain to lock the engine when slackening or tightening crankshaft pulley bolts • Mark the direction of the chain before removing • Crankshafts and Camshafts may only be turned with the chain drive mechanism fully installed. Part No. 1867 Diesel Timing Kit • Do not turn crankshaft via camshaft or other gears • Check the diesel injection pump timing after replacing the chain • Observe all tightening torques • Always refer to the vehicle manufacturer’s service manual or a suitable proprietary instruction book • Incorrect or out of phase engine timing can result in damage to the valves • It is always recommended to turn the engine slowly, by hand, and to re-check the camshaft and crankshaft timing positions A SE R R C op • Do not turn the crankshaft or camshaft when the timing belt/chain has been removed • It is always recommended to turn the engine slowly, by hand and to re-check the camshaft and crankshaft timing positions. LA 5 018341 018672 Guarantee If this product fails through faulty materials or workmanship, contact our service department direct on: +44 (0) 1926 818186. Normal wear & tear are excluded as are consumable items & abuse. www.lasertools.co.uk www.lasertools.co.uk C op LA ht y SE C ri yr SE C o g LA ig R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R ht SE C r y S C ig op ri ER R o gh L h p y A t C ri yr t SE C ER op gh i op gh LA R y LA t C r y t S C i op ri gh SE ER o g L py yr LA ht A t S C ig op ri SE ER o g L h py yr LA ht A t R SE C ig r SE C ig op LA ht R o LA ht R y SE C ig ri SE C o g LA ht R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R SE C ri yr SE C o g LA ig R op py LA ht R ht SE C r y S C ig op ri ER R op gh L h yr A t SE C yr t SE C i o g i R op py gh LA ht R LA C r y t S C i op ri gh S ER op g L yr LA ht A t C y S C ig op ri SE ER op g L h yr LA ht A t R y SE C ig r SE C ig op LA ht R LA ht R ri yr S C gh SE C ER ig op L op LA ht A t R y SE C ri yr SE C o g LA i R op py LA ht R SE C ri yr S C o g LA ER ig R op py LA ht ht SE C r y S C i op ri gh ER R op gh L yr A t SE C yr t SE C i o g i R op py gh LA ht R C ri yr t SE C op gh i o g L R Plan Layout Applications R The application list for this product has been compiled cross referencing the OEM Tool Code with the Component Code. SE R In most cases the tools are specific to this type of engine and are necessary for Cam belt or chain maintenance. If the engine has been identified as an interference engine valve to piston damage will occur if the engine is run with a broken Cam belt. LA A compression check of all cylinders should be performed before removing the cylinder head. Always consult a suitable work shop manual before attempting to change the Cam belt or Chain. The use of these engine timing tools is purely down to the user’s discretion and Tool Connection cannot be held responsible for any damage caused what so ever. B ALWAYS USE A REPUTABLE WORKSHOP MANUAL ri g ht C Manufacturer Model Style Citroën Berlingo 1.8 | 1.9D BX 1.7d | TD BX 1.9d C15 D R C op py A Ref Code A C062 7014-TN | TJ | 1860 863 000 8mm Cranked Setting Pin B C063 21-162B | 303-367 | 303-376B M8 x 35mm Set Screws C064 21-104 | 303-193 Description M8 x 40mm Set Screw Leyland Daf R C Oem Code A SE Peugeot Dispatch | Jumpy 1.9 | 2.1D | TD Relay | Jumper 1.9D | TD Synergie | Evasion 1.9 TD Synergie | Evasion 2.1TD Visa 1.7d Xantia 1.8 | 1.9d | TD Xantia 2.1 D | TD XM 2.1 | 2.2 TD Xsara 1.9 D | TD ZX 1.8 | 1.9 D | TD Sherpa DI 200 406 2.1 D Turbo 605 2.1 D Turbo 605 2.1D | Td 806 2.1 D Turbo LA Boxer Fiat Engine Code 161A 162 D8A D8B D8C D9B A8A A9A AJ2 DJY DJ2 DHV DHX DHW DHY XUD II BTE CP8C 2.5DT Ulyse E 1.90 D8B D8B Scudo 1.90 D9B D9B Ducato 1.90 DHX DHX DJY www.lasertools.co.uk www.eldontools. 2 www.lasertools.co.uk 3