1
Download Service Manual - Genie Industries
Transcript
Service Manual Serial Number Range TZ-50 TM from TZ5004-1 to TZ5012-253 Part No. 84577 Rev B1 September 2014 Introduction September 2014 INTRODUCTION Important Read, understand and obey the safety rules and operating instructions in the appropriate operator's manual on your machine before attempting any maintenance or repair procedure. This manual provides detailed scheduled maintenance information for the machine owner and user. It also provides troubleshooting fault codes and repair procedures for qualified service professionals. Basic mechanical, hydraulic and electrical skills are required to perform most procedures. However, several procedures require specialized skills, tools, lifting equipment and a suitable workshop. In these instances, we strongly recommend that maintenance and repair be performed at an authorized Genie dealer service center. Compliance Machine Classification Group B/Type 3 as defined by ISO 16368 Machine Design Life Unrestricted with proper operation, inspection and scheduled maintenance. Technical Publications Genie has endeavored to deliver the highest degree of accuracy possible. However, continuous improvement of our products is a Genie policy. Therefore, product specifications are subject to change without notice. Readers are encouraged to notify Genie of errors and send in suggestions for improvement. All communications will be carefully considered for future printings of this and all other manuals. Copyright © 2004 Terex Corporation 84577 Rev B May 2013 First Edition, Second Printing "Genie" and "TZ" are registered trademarks of Terex South Dakota, Inc. in the USA and many other countries. Printed on recycled paper Contact Us: Printed in U.S.A. http://www.genielift.com e-mail: [email protected] ii Genie TZ-50 Part No. 84577 September 2014 Revision History Revision Date A 11/2004 B 5/2013 B1 9/2014 Section Procedure / Schematic Page / Description New release Introduction Revision History Added 2 - Spec. Hydraulic Specifications SAE and Metric Fastener Torque Chart 3 - Maint. Added Specific maintenance to all axle procedures Revised procedures. 4 - Repair Revised procedures. 5 - Schem. Revised all schematics and grouped by Markets. 5 - Schem. 5-138, 5-139 REFERENCE EXAMPLES: Honda Engine_Section 2_Specifications. A-6,B-3,C-7_Section 3_Maintenance Procedure. 3-2, 6-4, 9-1_Section 4_Repair Procedure. 5-35, 5-56, 5-104_Section 5_Schematic Page #. Part No. 84577 Electronic Version Click on any procedure or page number highlighted in blue to view the update. Genie TZ-50 iii September 2014 REVISION HISTORY, CONTINUED Revision Date Section Procedure / Schematic Page / Description REFERENCE EXAMPLES: Honda Engine_Section 2_Specifications. A-6,B-3,C-7_Section 3_Maintenance Procedure. 3-2, 6-4, 9-1_Section 4_Repair Procedure. 5-35, 5-56, 5-104_Section 5_Schematic Page #. iv Electronic Version Click on any procedure or page number highlighted in blue to view the update. Genie TZ-50 Part No. 84577 September 2014 INTRODUCTION Serial Number Legend Part No. 84577 Genie TZ-50 v Section 1 • Safety Rules September 2014 Safety Rules Personal Safety Any person working on or around a machine must be aware of all known safety hazards. Personal safety and the continued safe operation of the machine should be your top priority. Read each procedure thoroughly. This manual and the decals on the machine, use signal words to identify the following: Danger Failure to obey the instructions and safety rules in this manual and the appropriate Operator's Manual on your machine will result in death or serious injury. Safety alert symbol—used to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Many of the hazards identified in the operator's manual are also safety hazards when maintenance and repair procedures are performed. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Do Not Perform Maintenance Unless: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. You are trained and qualified to perform maintenance on this machine. You read, understand and obey: - manufacturer’s instructions and safety rules - employer’s safety rules and worksite regulations - applicable governmental regulations Indicates a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, may result in property damage. You have the appropriate tools, lifting equipment and a suitable workshop. Be sure to wear protective eye wear and other protective clothing if the situation warrants it. Be aware of potential crushing hazards such as moving parts, free swinging or unsecured components when lifting or placing loads. Always wear approved steel-toed shoes. vi Genie TZ-50 Part No. 84577 September 2014 Section 1 • Safety Rules SAFETY RULES Workplace Safety Be sure to keep sparks, flames and lighted tobacco away from flammable and combustible materials like battery gases and engine fuels. Always have an approved fire extinguisher within easy reach. Be sure that all tools and working areas are properly maintained and ready for use. Keep work surfaces clean and free of debris that could get into machine components and cause damage. Be sure any forklift, overhead crane or other lifting or supporting device is fully capable of supporting and stabilizing the weight to be lifted. Use only chains or straps that are in good condition and of ample capacity. Be sure that fasteners intended for one time use (i.e., cotter pins and self-locking nuts) are not reused. These components may fail if they are used a second time. Be sure to properly dispose of old oil or other fluids. Use an approved container. Please be environmentally safe. Be sure that your workshop or work area is properly ventilated and well lit. Part No. 84577 Genie TZ-50 vii September 2014 Table of Contents Introduction Important Information ...................................................................................................... ii Revision History ............................................................................................................. iii Serial Number Legend ................................................................................................... v Section 1 Safety Rules General Safety Rules .................................................................................................... vi Section 2 Specifications Machine Specifications ............................................................................................. 2 - 1 Performance Specifications ...................................................................................... 2 - 2 Hydraulic Specifications ............................................................................................ 2 - 2 Manifold Component Specifications .......................................................................... 2 - 3 Machine Torque Specifications ................................................................................. 2 - 4 Honda GX160K1 Engine Specifications ................................................................... 2 - 5 Hydraulic Hose and Fitting Torque Specifications ..................................................... 2 - 6 SAE and Metric Fastener Torque Chart .................................................................... 2 - 8 Section 3 Scheduled Maintenance Procedures Introduction ............................................................................................................... 3 - 1 Pre-delivery Preparation Report ............................................................................... 3 - 3 Maintenance Inspection Report ................................................................................ 3 - 5 Checklist A Procedures viii A-1 Inspect the Manuals and Decals ..................................................................... 3 - 6 A-2 Perform Pre-operation Inspection ................................................................... 3 - 6 A-3 Perform Function Tests ................................................................................... 3 - 7 A-4 Perform Engine Maintenance (if equipped) ..................................................... 3 - 7 Genie TZ-50 Part No. 84577 September 2014 TABLE OF CONTENTS Section 3 Scheduled Maintenance Procedures, continued A-5 Torque the Lug Bolts - Electrical and Hydraulic Axles ..................................... 3 - 8 A-6 Torque the Lug Bolts - Mechanical Axle .......................................................... 3 - 8 A-7 Perform Hitch Maintenance - Hydraulic Axle ................................................... 3 - 9 A-8 Perform Engine Maintenance (if equipped) ..................................................... 3 - 9 A-9 Perform 30 Day Service ................................................................................ 3 - 10 A-10 Perform Engine Maintenance (if equipped) ................................................... 3 - 10 A-11 Grease the Turntable Rotation Bearing and Rotate Gear .............................. 3 - 11 A-12 Perform Engine Maintenance (if equipped) ................................................... 3 - 11 Checklist B Procedures B-1 Inspect the Batteries ..................................................................................... 3 - 12 B-2 Inspect the Electrical Wiring .......................................................................... 3 - 13 B-3 Test the Electrical Contactor ......................................................................... 3 - 14 B-4 Test the Emergency Stop ............................................................................. 3 - 14 B-5 Test the Key Switch ...................................................................................... 3 - 15 B-6 Test the Manual Override .............................................................................. 3 - 15 B-7 Perform Hydraulic Oil Analysis ...................................................................... 3 - 17 B-8 Perform Axle Maintenance - Electrical and Hydraulic Axles .......................... 3 - 18 B-9 Service the Tongue Jack .............................................................................. 3 - 18 B-10 Inspect the Parking Brake ............................................................................. 3 - 19 B-11 Check the Wheel Bearings - Mechanical Axle ............................................... 3 - 24 B-12 Service the Hitch - Mechanical Axle .............................................................. 3 - 25 B-13 Perform Axle Maintenance - Mechanical Axle ............................................... 3 - 26 B-14 Perform Engine Maintenance (if equipped) ................................................... 3 - 26 Part No. 84577 Genie TZ-50 ix September 2014 TABLE OF CONTENTS Section 3 Scheduled Maintenance Procedures, continued Checklist C Procedures C-1 Grease the Platform Overload Mechanism (if equipped) ............................... 3 - 27 C-2 Test the Platform Overload System (if equipped) .......................................... 3 - 27 C-3 Perform Axle Maintenance - Electrical and Hydraulic Axles .......................... 3 - 28 C-4 Replace the Hydraulic Tank Breather Cap Models with Optional Hydraulic Oil ................................................................ 3 - 29 C-5 Grease the Axle Wheel Bearings - Mechanical Axle ..................................... 3 - 29 C-6 Adjust the Brakes - Mechanical Axle ............................................................. 3 - 30 Checklist D Procedures D-1 Perform Axle Maintenance - Electrical and Hydraulic Axles .......................... 3 - 32 D-2 Check the Boom Wear Pads ......................................................................... 3 - 32 D-3 Replace the Hydraulic Tank Return Filter ...................................................... 3 - 33 D-4 Check the Turntable Rotation Bearing Bolts ................................................. 3 - 34 D-5 Inspect for Turntable Bearing Wear .............................................................. 3 - 35 Checklist E Procedures x E-1 Test or Replace the Hydraulic Oil .................................................................. 3 - 36 E-2 Perform Engine Maintenance (if equipped) ................................................... 3 - 37 Genie TZ-50 Part No. 84577 September 2014 TABLE OF CONTENTS Section 4 Repair Introduction ............................................................................................................... 4 - 1 Platform Components 1-1 Platform .......................................................................................................... 4 - 2 1-2 Platform Rotator .............................................................................................. 4 - 2 Jib Boom Components 2-1 Jib Boom ......................................................................................................... 4 - 4 2-2 Jib Boom Lift Cylinder ..................................................................................... 4 - 6 Primary Boom Components 3-1 Cable Track .................................................................................................... 4 - 9 3-2 Primary Boom ............................................................................................... 4 - 11 3-3 Primary Boom Lift Cylinder ........................................................................... 4 - 14 3-4 Platform Leveling Cylinders .......................................................................... 4 - 15 Secondary Boom Components 4-1 Secondary Boom .......................................................................................... 4 - 18 4-2 Secondary Boom Lift Cylinder ....................................................................... 4 - 21 Engine 5-1 Fuse Replacement ........................................................................................ 4 - 23 Ground Controls 6-1 Level Sensor ................................................................................................. 4 - 24 Hydraulic Pump 7-1 Function Pump .............................................................................................. 4 - 28 Manifolds Part No. 84577 8-1 Function Manifold Components ..................................................................... 4 - 30 8-2 Jib Manifold Components .............................................................................. 4 - 32 8-3 Drive Manifold Components (if equipped) ..................................................... 4 - 34 8-4 Valve Adjustments - Function Manifold ......................................................... 4 - 36 8-5 Valve Coils .................................................................................................... 4 - 38 Genie TZ-50 xi September 2014 TABLE OF CONTENTS Section 4 Repair, continued Hydraulic Tank 9-1 Hydraulic Tank .............................................................................................. 4 - 40 Axle Components 10-1 Axle ............................................................................................................... 4 - 41 Trailer Components 11-1 Hydraulic and Mechanical Brakes ................................................................. 4 - 42 11-2 Parking Brake ............................................................................................... 4 - 42 Outriggers 12-1 Outrigger Components .................................................................................. 4 - 43 12-2 Outrigger Cylinder ......................................................................................... 4 - 44 Platform Overload Components 13-1 Platform Overload System ............................................................................ 4 - 45 Drive Components 14-1 Drive Motor ................................................................................................... 4 - 47 14-2 Drive Control Box .......................................................................................... 4 - 48 xii Genie TZ-50 Part No. 84577 September 2014 TABLE OF CONTENTS Section 5 Schematics Introduction ............................................................................................................... 5 - 1 Electrical Abbreviations Legend ................................................................................ 5 - 2 Abbreviation Legend - Wire Colors ........................................................................... 5 - 4 Limit Switch Legend .................................................................................................. 5 - 5 Electrical Symbols Legend ....................................................................................... 5 - 6 Abbreviation Legend - Hydraulic Schematics ........................................................... 5 - 7 Hydraulic Symbols Legend ....................................................................................... 5 - 8 Honda GX160 Engine Wiring Diagram ..................................................................... 5 - 9 Trailer Lighting Wiring Diagram - ANSI / CSA ......................................................... 5 - 10 Trailer Lighting Wiring Diagram - Mechanical Axle, CE (to SN TZ5012-215) ...................................................................................... 5 - 11 Trailer Lighting Wiring Diagram - Mechanical Axle, CE (from SN TZ5012-216) .................................................................................. 5 - 12 Trailer Lighting Wiring Diagram - Electric Axle, AUS (to SN TZ5012-252) ...................................................................................... 5 - 13 Trailer Lighting Wiring Diagram - Electric Axle, AUS (from SN TZ5012-253) .................................................................................. 5 - 14 Trailer Lighting Wiring Diagram - Hydraulic Axle, AUS (from SN TZ5012-216) .................................................................................. 5 - 15 Part No. 84577 Genie TZ-50 xiii September 2014 TABLE OF CONTENTS Section 5 Schematics, continued Control Box Wiring Diagrams - ANSI/CSA Ground Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-181) ..................................................................... 5 - 16 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-182 to TZ5004-324) ......................................... 5 - 18 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-325 to TZ5005-284) ......................................... 5 - 20 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) ......................................... 5 - 22 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) ......................................... 5 - 24 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5011-132) ................................................................. 5 - 26 Platform Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-181) ..................................................................... 5 - 28 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-182 to TZ5005-284) ......................................... 5 - 29 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) ......................................... 5 - 30 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) ......................................... 5 - 31 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5011-132) ................................................................. 5 - 32 Drive Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-284) ..................................................................... 5 - 33 xiv Genie TZ-50 Part No. 84577 September 2014 TABLE OF CONTENTS Section 5 Schematics, continued Control Box Wiring Diagrams - AS/CE Ground Control Box Wiring Diagram - AS/CE (to serial number TZ5004-181) ..................................................................... 5 - 34 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-182 to TZ5004-324) ......................................... 5 - 36 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-325 to TZ5005-284) ......................................... 5 - 38 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5005-285 to TZ5010-144) ......................................... 5 - 40 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5010-145 to TZ5011-131) ......................................... 5 - 42 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5011-132) ................................................................. 5 - 44 Platform Control Box Wiring Diagram - AS/CE (to serial number TZ5004-181) ..................................................................... 5 - 46 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5004-182 to TZ5005-284) ......................................... 5 - 47 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5005-285 to TZ5010-144) ......................................... 5 - 48 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5010-145 to TZ5011-131) ......................................... 5 - 49 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5011-132) ................................................................. 5 - 50 Drive Control Box Wiring Diagram - AS/CE (to serial number TZ5004-284) ..................................................................... 5 - 51 Part No. 84577 Genie TZ-50 xv September 2014 TABLE OF CONTENTS Section 5 Schematics, continued Electrical Schematics - ANSI/CSA Electrical Schematic - ANSI/CSA (to serial number TZ5004-181) .......................... 5 - 54 Electrical Schematic - ANSI/CSA (from serial number TZ5004-182 to TZ5005-210) ......................................... 5 - 60 Electrical Schematic - ANSI/CSA (from serial number TZ5005-211 to TZ5005-284) ......................................... 5 - 66 Electrical Schematic - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) ......................................... 5 - 72 Electrical Schematic - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) ......................................... 5 - 78 Electrical Schematic - ANSI/CSA (from serial number TZ5011-132 to TZ5011-310) ......................................... 5 - 84 Electrical Schematic - ANSI/CSA (from serial number TZ5011-311) ...................... 5 - 90 Electrical Schematics - AS/CE Electrical Schematic - AS/CE (to serial number TZ5004-181) ................................ 5 - 96 Electrical Schematic - AS/CE (from serial number TZ5004-182 to TZ5005-210) ....................................... 5 - 102 Electrical Schematic - AS/CE (from serial number TZ5005-211 to TZ5005-284) ....................................... 5 - 108 Electrical Schematic - AS/CE (from serial number TZ5005-285 to TZ5010-144) ....................................... 5 - 114 Electrical Schematic - AS/CE (from serial number TZ5010-145 to TZ5011-131) ....................................... 5 - 120 Electrical Schematic - AS/CE (from serial number TZ5011-132 to TZ5011-310) ....................................... 5 - 126 Electrical Schematic - AS/CE (from serial number TZ5011-311) .......................... 5 - 132 Hydraulic Schematics Hydraulic Schematic (to serial number TZ5006-510) ............................................ 5 - 138 Hydraulic Schematic (from serial number TZ5006-511) ........................................ 5 - 139 xvi Genie TZ-50 Part No. 84577 September 2014 Section 2 • Specifications Specifications Machine Specifications Tires and wheels - Electric and Hydraulic Axles Batteries, models without drive option Axle Type 6V DC Group T-105 Quantity Battery capacity Reserve capacity @ 25A rate 4 225AH Tire size Load range 80 ft-lbs 108 Nm Tire pressure, maximum (cold) 65 psi 4.48 bar Tires and wheels - Mechanical Axle Type 6V DC Group T-145 Quantity Axle Tire size 530 minutes Fluid capacities Hydraulic system (including tank) C 244AH Lug bolt torque, dry Hydraulic tank 215/70R14 104/102N 4 Load range Reserve capacity @ 25A rate D Lug nut torque, dry 447 minutes Batteries, models with drive option Battery capacity ST225/75R15 Tire pressure, maximum (cold) 4.75 gallons 18 liters 8 gallons 30 liters 192 ft-lbs 260 Nm 66 psi 4.55 bar Tongue jack - all models To TZ5005-204 Tire size From TZ5005-205 Tire size 12 x 3.5 x 0.75 10 x 3 x 0.75 For operational specifications, refer to the Operator's Manual. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice. Part No. 84577 Genie TZ-50/30 2-1 Section 2 • Specifications September 2014 SPECIFICATIONS Performance Specifications Hydraulic Specifications Boom function speeds, maximum from platform controls (no weight in platform) Hydraulic Oil Specifications Primary boom up 18 to 26 seconds Hydraulic oil type Viscosity grade Viscosity index Primary boom down 17 to 26 seconds Cleanliness level, minimum Primary boom extend 13 to 20 seconds Water content, maximum Primary boom retract 16 to 24 seconds Secondary boom up 17 to 25 seconds Secondary boom up (with drive option) 20 to 30 seconds Secondary boom down 16 to 24 seconds Jib boom up 16 to 22 seconds Jib boom down 16 to 22 seconds Chevron Rando HD oil is fully compatible and mixable with Shell Donax TG (Dexron III) oils. Genie specifications require hydraulic oils which are designed to give maximum protection to hydraulic systems, have the ability to perform over a wide temperature range, and the viscosity index should exceed 140. They should provide excellent antiwear, oxidation, corrosion inhibition, seal conditioning, and foam and aeration suppression properties. Platform rotate (if equipped) Turntable rotate - 359° 8 to 12 seconds 110 to 140 seconds Airborne noise emissions 80 dB Maximum sound level at normal operation workstations (A-weighted) For operational specifications, refer to the Operators Manual. Chevron Rando HD equivalent Multi-viscosity 200 15/13 200 ppm Optional fluids Biodegradable Fire resistant Mineral based Petro Canada Environ MV 46 Statoil Hydra Way Bio Pa 32 BP Biohyd SE-S UCON Hydrolube HP-5046 Quintolubric 822 Shell Tellus S2 V 32 Shell Tellus S2 V 46 Chevron Aviation A Arnica 32 Note: Continued use of Chevron Aviation A hydraulic fluid when ambient temperatures are consistently above 32°F / 0°C may result in component damage. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice. 2-2 Genie TZ-50/30 Part No. 84577 September 2014 Section 2 • Specifications SPECIFICATIONS Note: Use Chevron Aviation A hydraulic fluid when ambient temperatures are consistently below 0°F / -17°C. Note: Use Shell Tellus S2 V 46 hydraulic oil when oil temperatures consistently exceed 205°F / 96°C. Note: Genie specifications require additional equipment and special installation instructions for the approved optional fluids. Consult the Genie Service Department before use. single section gear pump Displacement per revolution 0.244 cu in 4 cc Flow rate 2.8 gpm 10.6 L/min Hydraulic tank return line filter 10 micron Function pump (models with drive option) Type: System relief valve pressure 3000 psi 207 bar Turntable rotate relief valve pressure 600 psi 41 bar Primary boom down relief valve pressure 1600 psi 110 bar Manifold Component Specifications Function pump (models without drive option) Type: Function manifold 2 section pressure balanced gear pump Displacement per revolution 0.488 cu in 8 cc Flow rate 5.6 gpm 21.2 L/min Hydraulic tank return line filter 10 micron Plug torque SAE No. 2 36 in-lbs / 4 Nm SAE No. 4 10 ft-lbs / 13 Nm SAE No. 6 14 ft-lbs / 19 Nm SAE No. 8 38 ft-lbs / 51 Nm SAE No. 10 41 ft-lbs / 55 Nm SAE No. 12 56 ft-lbs / 76 Nm Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice. Part No. 84577 Genie TZ-50/30 2-3 Section 2 • Specifications September 2014 SPECIFICATIONS Machine Torque Specifications Platform rotator 3 /4 -10 center bolt, lubricated 3 /8 -16 bolts, lubricated 200 ft-lbs 271 Nm 32 ft-lbs 43 Nm Turntable rotate motor 1 /2 -13 bolts, dry 60 ft-lbs 81 Nm Turntable rotate motor pinion 5 /8 -18 bolt, dry 180 ft-lbs 244 Nm Turntable rotate bearing all bolts, lubricated 195 ft-lbs 264 Nm Hitch mounting bolts 5 /8 -11 bolts, dry 170 ft-lbs 230 Nm Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice. 2-4 Genie TZ-50/30 Part No. 84577 September 2014 Section 2 • Specifications SPECIFICATIONS Honda GX160K1 Engine Displacement Starter motor 9.9 cu in 163 cm2 Horsepower Ignition System Spark plug type 2.7 x 1.8 inches 68 x 45 mm BPR6ES (NGK) W20EPR-U (DENSO) Spark plug gap 0.028 to 0.031 inches 0.7 to 0.8 mm 5.4 hp @ 3600 rpm 4 kW @ 3600 rpm Engine idle - no load 3400 rpm Engine idle - under load (alternator) 3100 rpm Compression ratio Forced air 1 Number of cylinders Bore & stroke Cooling System 12 V DC Fuel Fuel tank capacity unleaded gasoline 86 octane minimum 0.95 gallons 3.6 liters 8.5:1 Valve Clearance, cold Intake 0.006 in (0.15 mm) Exhaust 0.008 in (0.20 mm) Lubrication system Oil capacity splash 0.63 quarts 0.6 liters Oil viscosity requirements Temperature below 30°F / 0°C 5W-30 -4°F to 100°F / -20°C to 38°C 10W-30 Temperature above 50°F / 10°C 30W Use oils meeting API classification SJ as they offer improved wear protection. Units ship with 10W-30 SJ. Continuous improvement of our products is a Genie policy. Product specifications are subject to change without notice. Part No. 84577 Genie TZ-50/30 2-5 Section 2 • Specifications September 2014 SPECIFICATIONS Hydraulic Hose and Fitting Torque Specifications SAE O-ring Boss Port (tube fitting - installed into Aluminum) (all types) Your machine is equipped with Parker Seal-Lok™ ORFS or 37° JIC fittings and hose ends. Genie specifications require that fittings and hose ends be torqued to specification when they are removed and installed or when new hoses or fittings are installed. SAE Dash size Seal-Lok™ Fittings (hose end - ORFS) SAE Dash size Torque Torque -4 14 ft-lbs / 19 Nm -6 23 ft-lbs / 31.2 Nm -8 36 ft-lbs / 54.2 Nm -10 62 ft-lbs / 84 Nm -12 84 ft-lbs / 114 Nm -16 125 ft-lbs / 169.5 Nm -4 10 ft-lbs / 13.6 Nm -20 151 ft-lbs / 204.7 Nm -6 30 ft-lbs / 40.7 Nm -24 184 ft-lbs / 249.5 Nm -8 40 ft-lbs / 54.2 Nm -10 60 ft-lbs / 81.3 Nm -12 85 ft-lbs / 115 Nm -16 110 ft-lbs / 150 Nm -20 140 ft-lbs / 190 Nm -24 180 ft-lbs / 245 Nm Jamb nut Non-adjustable fitting (Non-adj) Adjustable fitting (Adj) SAE O-ring Boss Port (tube fitting - installed into Steel) SAE Dash size JIC 37° Fittings -4 ORFS / 37° (Adj) ORFS (Non-adj) 37° (Non-adj) 15 ft-lbs / 20.3 Nm 26 ft-lbs / 35.3 Nm 22 ft-lbs / 30 Nm -6 ORFS (Adj / Non-adj) 37° (Adj / Non-adj) 35 ft-lbs / 47.5 Nm 29 ft-lbs / 39.3 Nm -8 ORFS (Adj / Non-adj) 37° (Adj / Non-adj) 60 ft-lbs / 81.3 Nm 52 ft-lbs / 70.5 Nm -10 ORFS (Adj / Non-adj) 37° (Adj / Non-adj) 100 ft-lbs / 135.6 Nm 85 ft-lbs / 115.3 Nm (swivel nut or hose connection) SAE Dash size 2-6 Thread Size Flats -4 7/16-20 2 -6 9/16-18 1 1/4 -8 3/4-16 1 -10 7/8-14 1 -12 1 1/16-12 1 -16 1 5/16-12 1 -20 1 5/8-12 1 -24 7/8-12 1 1 Torque -12 (All types) 135 ft-lbs / 183 Nm -16 (All types) 200 ft-lbs / 271.2 Nm -20 (All types) 250 ft-lbs / 339 Nm -24 (All types) 305 ft-lbs / 413.5 Nm Genie TZ-50/30 Part No. 84577 September 2014 Section 2 • Specifications SPECIFICATIONS Torque Procedure Seal-Lok™ fittings 1 Replace the O-ring. The O-ring must be replaced anytime the seal has been broken. The O-ring cannot be re-used if the fitting or hose end has been tightened beyond finger tight. a b c Note: The O-rings used in the Parker Seal Lok™ fittings and hose ends are custom-size O-rings. They are not standard SAE size O-rings. They are available in the O-ring field service kit (Genie part number 49612). Figure 1 a b c hex nut reference mark body hex fitting 3 Be sure that the face seal O-ring is seated and retained properly. 3 Working clockwise on the body hex fitting, make a second mark with a permanent ink marker to indicate the proper tightening position. Refer to Figure 2. 4 Position the tube and nut squarely on the face seal end of the fitting and tighten the nut finger tight. Note: Use the JIC 37° Fittings table on the previous page to determine the correct number of flats for the proper tightening position. 5 Tighten the nut or fitting to the appropriate torque per given size as shown in the table. Note: The marks indicate that the correct tightening positions have been determined. Use the second mark on the body hex fitting to properly tighten the joint after it has been loosened. 2 Lubricate the O-ring before installation. 6 Operate all machine functions and inspect the hoses and fittings and related components to confirm that there are no leaks. JIC 37° fittings 1 Align the tube flare (hex nut) against the nose of the fitting body (body hex fitting) and tighten the hex nut to the body hex fitting to hand-tight, approximately 30 in-lbs / 3.4 Nm. b a c 2 Make a reference mark on one of the flats of the hex nut, and continue it on to the body hex fitting with a permanent ink marker. Refer to Figure 1. b Figure 2 a b c body hex fitting reference mark second mark 4 Tighten the hex nut until the mark on the hex nut is aligned with the second mark on the body hex fitting. 5 Operate all machine functions and inspect the hoses and fittings and related components to confirm that there are no leaks. Part No. 84577 Genie TZ-50/30 2-7 Section 2 • Specifications September 2014 SPECIFICATIONS 4.6 2-8 8.8 Genie TZ-50/30 10.9 12.9 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures Scheduled Maintenance Procedures About This Section This section contains detailed procedures for each scheduled maintenance inspection. Each procedure includes a description, safety warnings and step-by-step instructions. Observe and Obey: Symbols Legend Safety alert symbol—used to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Maintenance inspections shall be completed by a person trained and qualified on the maintenance of this machine. Scheduled maintenance inspections shall be completed daily, quarterly and semi-annually as specified on the Maintenance Inspection Report. The frequency and extent of periodical examinations and tests may also depend on national regulations. Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Failure to properly complete each inspection when required may cause death, serious injury or substantial machine damage. Indicates a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Immediately tag and remove from service a damaged or malfunctioning machine. Repair any machine damage or malfunction before operating the machine. Indicates a potentially hazardous situation which, if not avoided, may result in property damage. Use only Genie approved replacement parts. Machines that have been out of service for a period longer than 3 months must complete the quarterly inspection. Unless otherwise specified, perform each maintenance procedure with the machine in the following configuration: Indicates that a specific result is expected after performing a series of steps. Indicates that an incorrect result has occurred after performing a series of steps. • Machine disconnected from tow vehicle • Machine parked on a firm, level surface • Boom in the stowed position with both latches secured • Key switch in the off position with the key removed • Wheels chocked • Parking brake applied Part No. 84577 Genie TZ-50 3-1 Section 3 • Scheduled Maintenance Procedures September 2014 SCHEDULED MAINTENANCE PROCEDURES Maintenance Symbols Legend Pre-delivery Preparation Report The pre-delivery preparation report contains checklists for each type of scheduled inspection. The following symbols have been used in this manual to help communicate the intent of the instructions. When one or more of the symbols appears at the beginning of a maintenance procedure, it conveys the meaning below. Make copies of the Pre-delivery Preparation report to use for each inspection. Store completed forms as required. Maintenance Schedule Indicates that tools will be required to perform this procedure. Indicates that new parts will be required to perform this procedure. Indicates that a cold engine will be required to perform this procedure. There are five types of maintenance inspections that must be performed according to a schedule— daily, quarterly, semi-annually, annually, and two year. The Scheduled Maintenance Procedures Section and the Maintenance Inspection Report have been divided into five subsections—A, B, C, D, and E. Use the following chart to determine which group(s) of procedures are required to perform a scheduled inspection. Inspection Checklist Daily or every 8 hours Quarterly or every 250 hours or every 3000 miles / 4800 km Indicates that a warm engine will be required to perform this procedure. Semi-annually or every 500 hours or every 6000 miles / 9600 km Indicates that dealer service is required to perform this procedure. Annually or every 1000 hours or every 12,000 miles / 19,300 km Two year or every 2000 hours A A+B A+B+C A+B+C+D A+B+C+D+E Maintenance Inspection Report The maintenance inspection report contains checklists for each type of scheduled inspection. Make copies of the Maintenance Inspection Report to use for each inspection. Maintain completed forms for a minimum of 4 years or in compliance with employer, jobsite and governmental regulations and requirements. 3-2 Genie TZ-50 Part No. 84577 Pre-Deliver Pre-Deliveryy Preparation September 2014 Section 3 • Scheduled Maintenance Procedures Fundamentals Instructions It is the responsibility of the dealer to perform the Pre-delivery Preparation. Use the operator’s manual on your machine. The Pre-delivery Preparation is performed prior to each delivery. The inspection is designed to discover if anything is apparently wrong with a machine before it is put into service. A damaged or modified machine must never be used. If damage or any variation from factory delivered condition is discovered, the machine must be tagged and removed from service. Repairs to the machine may only be made by a qualified service technician, according to the manufacturer's specifications. Scheduled maintenance inspections shall be performed by qualified service technicians, according to the manufacturer's specifications and the requirements listed in the responsibilities manual. The Pre-delivery Preparation consists of completing the Pre-operation Inspection, the Maintenance items and the Function Tests. Use this form to record the results. Place a check in the appropriate box after each part is completed. Follow the instructions in the operator’s manual. If any inspection receives an N, remove the machine from service, repair and re-inspect it. After repair, place a check in the R box. Legend Y = yes, completed N = no, unable to complete R = repaired Comments Pre-Delivery Preparation Y N Pre-operation inspection completed Maintenance items completed Function tests completed Model Serial number Date Machine owner Inspected by (print) Inspector signature Inspector title Inspector company Terex South Dakota, Inc USA 500 Oak Wood Road PO Box 1150 Watertown, SD 57201-6150 (605) 882-4000 Part No. 84577 Genie UK The Maltings, Wharf Road Grantham, Lincolnshire NG31- 6BH England (44) 1476-584333 Genie TZ-50 3-3 R Section 3 • Scheduled Maintenance Procedures September 2014 This page intentionally left blank. 3-4 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures Maintenance Inspection Report Model Checklist A Y N R Checklist B A-1 Manuals and Decals B-1 Batteries A-2 Pre-operation inspect B-2 Electrical wiring Date A-3 Function tests B-3 Electrical Contactor A-4 Engine maintenance (if equipped) B-4 Emergency Stop Hour meter A-5 Lug bolts B-6 Manual override A-6 Lug bolts B-7 Hydraulic oil analysis Inspected by (print) A-7 Hitch maintenance B-8 Axle maintenance Inspector signature A-8 Engine maintenance (if equipped) B-9 Tongue jack Serial number Machine owner Perform after 40 hours: Inspector title A-9 Perform 30 day service Perform every 50 hours: Inspector company A-10 Engine maintenance (if equipped) Instructions • Make copies of this report to use for each inspection. Perform every 100 hours: A-11 Grease rotate bearing • Select the appropriate checklist(s) for the type of inspection to be performed. Daily or 8 hours Inspection: A-12 Engine maintenance (if equipped) Y N R B-5 Key switch B-10 Parking brake B-11 Wheel bearings B-12 Hitch B-13 Axle maintenance Perform every 300 hours: B-14 Engine maintenance (if equipped) Checklist C Y N R C-1 Grease platform overload (if equipped) C-2 Test platform overload (if equipped) A Quarterly or 250 hours or 3000 mile / 4800 km Inspection: A+B C-3 Axle maintenance C-4 Breather Cap Semi-annually or 500 hours or 6000 mile / 9600 km Inspection: A+B+C C-5 Axle wheel bearings Annually or 1000 hours or 12,000 mile / 19,300 km Inspection: A+B+C+D Checklist D C-6 Brakes Y N R D-1 Axle maintenance D-2 Boom wear pads Two year or 2000 hours Inspection: A+B+C+D+E D-3 Hydraulic return filter D-4 Turntable bearing bolts • Place a check in the appropriate box after each inspection procedure is completed. • Use the step-by-step procedures in this section to learn how to perform these inspections. D-5 Turntable bearing wear Checklist E - Rev A Y N R E-1 Hydraulic oil E-2 Engine maintenance (if equipped) • If any inspection receives an “N”, tag and remove the machine from service, repair and re-inspect it. After repair, place a check in the “R” box. Legend Y = yes, acceptable N = no, remove from service R = repaired Comments Part No. 84577 Genie TZ-50 3-5 Section 3 • Scheduled Maintenance Procedures September 2014 Checklist A Procedures A-1 Inspect the Manuals and Decals Genie specifications require that this procedure be performed daily or every 8 hours, whichever comes first. Maintaining the operator’s and safety manuals in good condition is essential to safe machine operation. Manuals are included with each machine and should be stored in the container provided in the platform. An illegible or missing manual will not provide safety and operational information necessary for a safe operating condition. In addition, maintaining all of the safety and instructional decals in good condition is mandatory for safe machine operation. Decals alert operators and personnel to the many possible hazards associated with using this machine. They also provide users with operation and maintenance information. An illegible decal will fail to alert personnel of a procedure or hazard and could result in unsafe operating conditions. 3 Open the operator's manual to the decals inspection section. Carefully and thoroughly inspect all decals on the machine for legibility and damage. Result: The machine is equipped with all required decals, and all decals are legible and in good condition. Result: The machine is not equipped with all required decals, or one or more decals are illegible or in poor condition. Remove the machine from service until the decals are replaced. 4 Always return the manuals to the storage container after use. Note: Contact your authorized Genie distributor or Genie if replacement manuals or decals are needed. 1 Check to make sure that the operator's and safety manuals are present and complete in the storage container on the platform. 2 Examine the pages of each manual to be sure that they are legible and in good condition. Result: The operator's manual is appropriate for the machine and all manuals are legible and in good condition. Result: The operator's manual is not appropriate for the machine or all manuals are not in good condition or are illegible. Remove the machine from service until the manual is replaced. 3-6 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST A PROCEDURES A-2 Perform Pre-operation Inspection A-4 Perform Engine Maintenance (if equipped) Completing a Pre-operation Inspection is essential to safe machine operation. The Pre-operation Inspection is a visual inspection performed by the operator prior to each work shift. The inspection is designed to discover if anything is apparently wrong with a machine before the operator performs the function tests. The Pre-operation Inspection also serves to determine if routine maintenance procedures are required. Engine specifications require that this procedure be performed every 8 hours or daily, whichever comes first. Complete information to perform this procedure is available in the appropriate operator's manual. Refer to the Operator's Manual on your machine. Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630). • Check oil level • Check air cleaner Honda GX160 Owner's Manual Genie part number A-3 Perform Function Tests 97228 Completing the function tests is essential to safe machine operation. Function tests are designed to discover any malfunctions before the machine is put into service. A malfunctioning machine must never be used. If malfunctions are discovered, the machine must be tagged and removed from service. Complete information to perform this procedure is available in the appropriate operator's manual. Refer to the Operator's Manual on your machine. Part No. 84577 Genie TZ-50 3-7 Section 3 • Scheduled Maintenance Procedures CHECKLIST A September 2014 PROCEDURES A-5 Torque the Lug Bolts Electrical and Hydraulic Axles A-6 Torque the Lug Bolts Mechanical Axle Axle specifications require that this procedure be performed initially after 10, 25 and 50 miles. Axle specifications require that this procedure be performed initially after 50 km, or 50 km after a wheel change. Proper axle maintenance, following the axle manufacturer's maintenance schedule, is essential to good axle performance and service life. Failure to perform the maintenance procedures can lead to poor axle performance and component damage. 1 Check each lug bolt for proper torque. Refer to Section 2, Specifications. Proper axle maintenance, following the axle manufacturer's maintenance schedule, is essential to good axle performance and service life. Failure to perform the maintenance procedures can lead to poor axle performance and component damage. 1 Check each lug bolt for proper torque. Refer to Section 2, Specifications. Required maintenance procedures and additional axle information is available in the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). Dexter Axle Operation Maintenance Service Manual Genie part number 84376 KNOTT Axle Service Manual Genie part number 3-8 Genie TZ-50 84443 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST A PROCEDURES A-7 Perform Hitch Maintenance Hydraulic Axle A-8 Perform Engine Maintenance (if equipped) Hitch specifications require that this procedure be performed weekly. Engine specifications require that this procedure be performed initially at 20 hours or 30 days, whichever comes first. • Brake fluid level • Inspect actuator • Replace engine oil Required maintenance procedures and additional hitch information is available in the Demco Model 91 Brake Actuators Owner/Operator Manual (Demco part number BH20023). Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630). Demco Model 91 Owner/Operator Manual Genie part number Honda GX160 Owner's Manual Genie part number Part No. 84577 84592 Genie TZ-50 97228 3-9 Section 3 • Scheduled Maintenance Procedures CHECKLIST A September 2014 PROCEDURES A-9 Perform 30 Day Service A-10 Perform Engine Maintenance (if equipped) The 30 day maintenance procedure is a onetime procedure to be performed after the first 30 days or 40 hours of usage. After this interval, refer to the maintenance tables for continued scheduled maintenance. Engine specifications require that this procedure be performed every 50 hours or quarterly, whichever comes first. Perform this procedure more often if dusty conditions exist. 1 Perform the following maintenance procedures: • Air filter • A-11 Grease the Turntable Rotation Bearing and Rotate Gear • B-7 Check the Turnable Rotation Bearing Bolts • B-10 Inspect the Parking Brake • D-4 Replace the Hydraulic Tank Return Filter 3 - 10 Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630). Honda GX160 Owner's Manual Genie part number Genie TZ-50 97228 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST A PROCEDURES A-11 Grease the Turntable Rotation Bearing and Rotate Gear A-12 Perform Engine Maintenance (if equipped) Genie specifications require that this procedure be performed every 100 hours of operation. Engine specifications require that this procedure be performed every 6 months or every 100 hours, whichever comes first. Perform this procedure more often if dusty conditions exist. Regular application of lubrication to the turntable bearing and rotate gear is essential to good machine performance and service life. Continued use of an insufficiently greased bearing and gear will result in component damage. 1 Raise the boom enough to access the turntable bearing. 2 Before serial number TZ5004-391: Locate the grease fitting on the inside of the turntable rotation bearing. After serial number TZ5004-390: Locate the grease fitting below the ground control box. • Replace engine oil • Clean fuel sediment cup • Check/clean spark plug Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630). Honda GX160 Owner's Manual Genie part number 97228 3 Pump multipurpose grease into the turntable rotation bearing. Rotate the turntable in increments of 4 to 5 inches / 10 to 13 cm at a time and repeat this step until the entire bearing has been greased. 4 Apply grease to each tooth of the drive gear located under the turntable. Grease type Part No. 84577 Multipurpose grease Genie TZ-50 3 - 11 Section 3 • Scheduled Maintenance Procedures September 2014 Checklist B Procedures 3 Be sure that the battery retaining fasteners and cable connections are tight. B-1 Inspect the Batteries 4 Remove the battery vent caps from all batteries and check the specific gravity of each battery cell with a hydrometer. Proper battery condition is essential to good machine performance and operational safety. Improper fluid levels or damaged cables and connections can result in component damage and hazardous conditions. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. Result: If any battery cell displays a specific gravity of less than 1.026, the battery must be replaced. 5 Check the battery acid level of each battery. If needed, replenish with distilled water to the bottom of the battery fill tube. Do not overfill. 6 Install the battery vent caps. 7 Check each battery pack and verify that the batteries are wired correctly. Bodily injury hazard. Batteries contain acid. Avoid spilling or contacting battery acid. Neutralize battery acid spills with baking soda and water. Battery Charger Side Ground Control Side - - + Note: Perform this procedure after fully charging the batteries. + - + + - + - Motor Controller 3 + - Note: For a more accurate determination of battery condition, fully charge the batteries and allow the batteries to rest 24 hours before performing this procedure to allow the battery cells to equalize. Black Pump Motor Charger Red 1 A1 D1 M- B- A2 B+ 275A Fuse 1 Put on protective clothing and eye wear. 2 Be sure that the battery cable connections are free of corrosion. 3 - 12 8 Inspect the battery charger plug and pigtail for damage or excessive insulation wear. Replace as required. Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B 9 Connect the battery charger to a properly grounded 115V/60Hz or 230V/60Hz single phase AC power supply. PROCEDURES B-2 Inspect the Electrical Wiring Result: The charger should operate and begin charging the batteries. Result: Simultaneously, the charger alarm sounds and the LED's blink one time. Correct the charger connections at the fuse and battery. The charger will then operate correctly and begin charging the batteries. Result: Simultaneously, the charger alarm sounds and the LED's blink two times. The input voltage is too low or too high. Correct the voltage issue. The charger will then operate correctly and begin charging the batteries. Result: Simultaneously, the charger alarm sounds and the LED's blink three times. The charger is overheated. Allow the charger to cool. The charger will then operate correctly and begin charging the batteries. Note: If you have any further questions regarding the battery charger operation, please contact Genie Product Support. Maintaining electrical wiring in good condition is essential to safe operation and good machine performance. Failure to find and replace burnt, chafed, corroded or pinched wires could result in unsafe operating conditions and may cause component damage. Electrocution hazard. Contact with hot or live circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 1 Inspect the following areas for burnt, chafed, corroded and loose wires: • Turntable area • Ground controls • Power unit wiring 2 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 3 Raise the secondary boom until the platform is approximately 10 feet / 3 m off the ground. 4 Inspect the boom storage area for burnt, chafed and pinched cables. 5 Lower the boom to the stowed position and turn the machine off. 6 Inspect the following areas for burnt, chafed, corroded, pinched and loose wires: • Boom to platform cable harness • Primary and secondary booms Part No. 84577 Genie TZ-50 3 - 13 Section 3 • Scheduled Maintenance Procedures CHECKLIST B September 2014 PROCEDURES B-3 Inspect the Electrical Contactor A properly functioning Emergency Stop is essential for safe machine operation. An improperly operating red Emergency Stop button will fail to shut off power and stop all machine functions, resulting in a hazardous situation. Genie requires that this procedure be performed every 250 hours or quarterly, whichever comes first. Maintaining the electrical contactor in good condition is essential to safe machine operation. Failure to locate a worn or damaged contactor could result in an unsafe working condition and component damage. 1 At the ground controls, turn the key switch to the off position and push in the red Emergency Stop button to the off position. 2 Disconnect the batteries. 3 Locate the electrical contactor mounted on the fuse bracket. 4 Visually inspect the contact points of the contactor for the following items: 1 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. Pull out the red Emergency Stop button to the on position at the drive controls (if equipped). 2 Push in the red Emergency Stop button at the ground controls to the off position. Result: No machine functions should operate. Note: The red Emergency Stop button at the ground controls will stop all machine operation without regard to the position of the key switch. 3 Turn the key switch to platform control and pull out the red Emergency Stop button to the on position at the ground controls. • Excessive burns 4 Push down the red Emergency Stop button at the platform controls to the off position. • Excessive arcs • Excessive pitting Electrocution/burn hazard. Contact with hot or live circuits could result in death or serious injury. Remove all rings, watches and other jewelry. Note: Replace the contactor if any damage is found. B-4 Test the Emergency Stop Result: No machine functions should operate. Models with drive (option): 5 Pull out the red Emergency Stop button to the on position at the platform controls. 6 Push down the red Emergency Stop button at the drive controls to the off position. Result: The drive function should not operate. 3 - 14 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B PROCEDURES B-5 Test the Key Switch B-6 Test the Manual Override Proper key switch action and response is essential to safe machine operation. The machine can be operated from the ground or platform controls and the activation of one or the other is accomplished with the key switch. Failure of the key switch to activate the appropriate control panel could cause a hazardous operating situation. Testing the manual override for malfunctions is essential for safe machine operation. An unsafe working condition exists if the manual override function does not operate in the event of a main power loss. Note: Perform this procedure from the ground using the platform controls. Do not stand in the platform. 1 Locate the turntable rotate valve coils on the function manifold. Push in and hold the red thumbscrew at the center of the valve stem. 1 Pull out the red Emergency Stop button to the on position at both the ground and platform controls. Pull out the red Emergency Stop button to the on position at the drive controls (if equipped). Turntable Rotate Result: The head of the thumbscrew should move 1/4 inch / 6 mm inwards. 2 Turn the key switch to platform control. a 3 Check the machine functions from the ground controls. b Result: The machine functions should not operate. c 4 Check the machine functions from the drive controls. d Result: The drive functions should operate. 5 Turn the key switch to ground control. 6 Check the machine functions from the platform controls. e Result: The machine functions should not operate. a b c d e 7 Check the machine functions from the drive controls. Result: The drive functions should operate. 8 Turn the key switch to the off position. Result: No function should operate. Part No. 84577 turntable rotate valve secondary boom down valve primary boom down valve primary boom up valve boom extend/retract valve 2 Release the red thumbscrew at the center of the valve stem, to reset the valve. Note: The valve spool must be reset for the turntable rotate function to operate from the machine controls. Genie TZ-50 3 - 15 Section 3 • Scheduled Maintenance Procedures CHECKLIST B September 2014 PROCEDURES 3 Pull out and hold the red thumbscrew at the center of the valve stem. Primary Boom Down Result: The head of the thumbscrew should move 1/4 inch / 6 mm outwards. 4 Release the red thumbscrew at the center of the valve stem, to reset the valve. Note: The valve spool must be reset for the turntable rotate function to operate from the machine controls. 7 Locate the primary boom down valve coil on the function manifold. Push in and turn fully in a counter clockwise direction the red thumbscrew at the center of the valve stem. Result: The head of the thumbscrew should rotate one-quarter turn in a counter clockwise direction. 8 Push in and turn fully in a clockwise direction the red thumbscrew at the center of the valve stem, to reset the valve. Secondary Boom Down 5 Locate the secondary boom down valve coil on the function manifold. Push in and turn fully in a counter clockwise direction the red thumbscrew at the center of the valve stem. Result: The head of the thumbscrew should rotate one-quarter turn in a counter clockwise direction. 6 Push in and turn fully in a clockwise direction the red thumbscrew at the center of the valve stem, to reset the valve. Note: The valve spool must be reset for the secondary boom down function to operate from the machine controls. Note: The valve spool must be reset for the primary boom down function to operate from the machine controls. Primary Boom Up 9 Locate the primary boom up valve coil on the function manifold. Push in and turn fully in a counter clockwise direction the red thumbscrew at the center of the valve stem. Result: The head of the thumbscrew should rotate one-quarter turn in a counter clockwise direction. 10 Push in and turn fully in a clockwise direction the red thumbscrew at the center of the valve stem, to reset the valve. Note: The valve spool must be reset for the primary boom up function to operate from the machine controls. 3 - 16 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B Boom Extend/Retract 11 Locate the boom extend/retract valve coils on the function manifold. Push in and hold the red thumbscrew at the center of the valve stem. Result: The head of the thumbscrew should move 1/4 inch / 6 mm inwards. 12 Release the red thumbscrew at the center of the valve stem, to reset the valve. Note: The valve spool must be reset for the turntable rotate function to operate from the machine controls. 13 Locate the boom extend/retract valve coils on the function manifold. Pull out and hold the red thumbscrew at the center of the valve stem. Result: The head of the thumbscrew should move 1/4 inch / 6 mm outwards. 14 Release the red thumbscrew at the center of the valve stem, to reset the valve. PROCEDURES B-7 Perform Hydraulic Oil Analysis Replacement or testing of the hydraulic oil is essential for good machine performance and service life. Dirty oil may cause the machine to perform poorly and continued use may cause component damage. Extremely dirty conditions may require oil changes to be performed more often. Note: Before replacing the hydraulic oil, the oil may be tested by an oil distributor for specific levels of contamination to verify that changing the oil is necessary. If the hydraulic oil is not replaced at the two year inspection, test the oil quarterly. Replace the oil when it fails the test. See E-1, Test or Replace the Hydraulic Oil. Note: The valve spool must be reset for the turntable rotate function to operate from the machine controls. Part No. 84577 Genie TZ-50 3 - 17 Section 3 • Scheduled Maintenance Procedures CHECKLIST B September 2014 PROCEDURES B-8 Perform Axle Maintenance Electrical and Hydraulic Axles B-9 Service the Tongue Jack Axle specifications require that this procedure be performed quarterly or every 3000 miles, whichever comes first. • Brake Adjustment Required maintenance procedures and additional axle information is available in the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). Dexter Axle Operation Maintenance Service Manual Genie part number 84376 Maintaining the tongue jack in good condition is essential to safe operation and good machine performance. Failure to lubricate the internal gears and bearings of the jack and axle bolt could result in unsafe operating conditions and may cause component damage. Jack specifications require that this procedure be performed quarterly or every 3000 miles, whichever comes first. 1 Remove the cap from the top of the jack housing and, using automotive grease, lightly grease the internal gears. Rotate the handle to evenly distribute the lubricant to the internal gears. 2 Securely install the cap onto the jack. 3 - 18 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B 7 Loosen the set screw at the side of the parking brake handle. B-10 Inspect the Parking Brake A properly functioning parking brake is essential to safe machine operation. The parking brake is manually activated. An improperly functioning parking brake will prevent the operator from properly securing the machine when not in use. ANSI models without drive option: 1 Visually inspect the parking brake cables and components for damage. 2 Visually inspect the parking brake cables to ensure both are properly secured and installed into the brake backing plate. 3 Set the parking brake. Note: If the brake cables are too tight the parking brake assembly will be difficult to apply. If the brake cables are too loose, the brakes will not activate when the lever is set. Result: The machine should not move. Result: The machine moves. Proceed to step 5. 6 Release the parking brake. 8 Adjust the handle just to the point where it is difficult to apply the parking brake, then rotate the top of the parking brake handle counterclockwise one full turn. 9 Tighten the set screw. Do not overtighten. 10 Engage the parking brake. Attempt to move the machine in both directions. Result: The parking brake should prevent the machine from moving. If the parking brake does not prevent the machine from moving, repeat steps 5 through 8 until the adjustment is correct OR see B-8, Perform Axle Maintenance Electrical and Hydraulic Axles CE models without drive option: 1 Visually inspect the parking brake cables and components for damage. 2 Visually inspect the parking brake cables to ensure both are properly secured and installed into the brake backing plate. 3 Set the parking brake. 4 Attempt to manually push the machine. 5 Chock the wheels PROCEDURES Note: If the brake cables are too tight the parking brake assembly will be difficult to apply. If the brake cables are too loose, the brakes will not activate when the lever is set. 4 Attempt to manually push the machine. Result: The machine should not move. Result: The machine moves. Proceed to step 5. Part No. 84577 Genie TZ-50 3 - 19 Section 3 • Scheduled Maintenance Procedures CHECKLIST B September 2014 PROCEDURES 5 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 6 Release the parking brake. 7 Pull out the nose of the hitch as far as it will go. 8 Loosen the lock nuts at the tension equalizer. 16 Engage the parking brake. Attempt to move the machine in both directions. Result: The parking brake should prevent the machine from moving. If the parking brake does not prevent the machine from moving, repeat steps 5 through 16 until adjustment is correct OR see B-13, Perform Axle Maintenance - Mechanical Axles. 9 Turn the wheel in a forward motion, adjusting the wheel brakes until the wheel turns with difficulty or not at all. ANSI models with drive option: 10 Adjust the wheel brakes until the wheel turns freely. 1 Visually inspect the parking brake cables and components for damage. Note: Slight rubbing noises, which do not affect the free turning of the wheel, are permitted. 11 Repeat steps 9 and 10 for the other wheel. 2 Visually inspect the parking brake cables to ensure all are properly secured and installed into the brake backing plate and parking brake balance bar. 12 Engage and release the parking brake 4 times. 3 Set the parking brake. 13 Tighten the nuts on the tension equalizer bracket until the bracket is balanced. Securely tighten the lock nuts. Note: If the brake cables are too tight the parking brake assembly will be difficult to apply. If the brake cables are too loose, the brakes will not activate when the lever is set. 14 Adjust the linkage until it is free of play and without initial tension. 4 Attempt to manually push the machine. 15 Lower the machine and return the outriggers to the stowed position. Result: The machine should not move. Result: The machine moves. Proceed to step 5. 3 - 20 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B PROCEDURES 5 Adjust the brakes. See B-8, Perform Axle Maintenance - Electrical and Hydraulic Axles Models to TZ5006-510 a 6 Chock the wheels b c d e f g h 7 Release the parking brake. 8 Loosen the set screw at the side of the parking brake handle. 9 Adjust the handle just to the point where it is difficult to apply the parking brake, then rotate the top of the parking brake handle counterclockwise one full turn. 10 Tighten the set screw. Do not overtighten. 11 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. Models from TZ5006-511 h 12 Engage the parking brake. I b c a 13 Remove the parking brake cylinder inspection cover. 14 Adjust the parking brake cylinder input cable until the cylinder flange just contacts the cylinder slider assembly. a b c d e f g h i Part No. 84577 Genie TZ-50 rear (chassis) parking brake cable cylinder output rod / threaded rod tension equalizer bracket parking brake cylinder cylinder flange slider assembly drive motor brake cable cylinder input cable / parking brake cable threaded rod 3 - 21 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST B PROCEDURES 15 Release the parking brake. CE models with drive option: 16 Adjust both rear parking brake cables at the tension equalizer bracket until, when turning the wheel in the direction of travel, a slight rubbing noise can be heard from the brakes. Loosen the cables just until no noise can be heard when turning the wheels. 1 Visually inspect the parking brake cables and components for damage. Note: Be sure a minimum of one full thread of the cable end is showing through the adjustment nut at the tension equalizer bracket. 17 Tighten the nuts on the tension equalizer bracket until the bracket is balanced. Securely tighten the lock nuts. 2 Visually inspect the parking brake cables to ensure all are properly secured and installed into the brake backing plate and parking brake balance bar. 3 Set the parking brake. Note: If the brake cables are too tight the parking brake assembly will be difficult to apply. If the brake cables are too loose, the brakes will not activate when the lever is set. 4 Attempt to manually push the machine. 18 Engage the parking brake. 19 Engage both drive motors. Result: The machine should not move. 20 Working from the front end of the parking brake cylinder, adjust the drive motor brake cables by hand until they have zero play and zero resistance. Be sure the brake cylinder balancebar is square to the parking brake input cable. Result: The machine moves. Proceed to step 5. 5 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 21 Disengage both drive motors. 7 Pull out the nose of the hitch as far as it will go. 22 Engage the parking brake. Attempt to move the machine in both directions. 8 Remove the parking brake cylinder inspection cover. 6 Release the parking brake. Result: The parking brake should prevent the machine from moving. If the parking brake does not prevent the machine from moving, repeat this procedure beginning with step 5. 3 - 22 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B PROCEDURES 9 Visually inspect the parking brake cables to ensure all are properly secured and installed into the brake backing plate and tension equalizer bracket. Models to TZ5006-510 a b c d e f g 10 Loosen the lock nuts at the tension equalizer bracket. 11 Turn the wheel in a forward motion, adjusting the wheel brakes until the wheel turns with difficulty or not at all. 12 Adjust the wheel brakes until the wheel turns freely. h Note: Slight rubbing noises, which do not affect the free turning of the wheel, are permitted. 13 Repeat steps 11 and 12 for the other wheel. 14 Engage and release the parking brake 4 times. 15 Engage the parking brake. 16 Adjust the parking brake cylinder input cable until the cylinder flange just contacts the cylinder slider assembly. 17 Release the parking brake. Models from TZ5006-511 h I b c 18 Adjust both rear parking brake cables at the tension equalizer bracket until, when turning the wheel in the direction of travel, a slight rubbing noise can be heard from the brakes. Loosen the cables just until no noise can be heard when turning the wheels. a Note: Be sure a minimum of one full thread of the cable end is showing through the adjustment nut at the tension equalizer bracket. a b c d e f g h i Part No. 84577 rear (chassis) parking brake cable cylinder output rod / threaded rod tension equalizer bracket parking brake cylinder cylinder flange slider assembly drive motor brake cable cylinder input cable / parking brake cable threaded rod Genie TZ-50 3 - 23 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST B PROCEDURES 19 Tighten the nuts on the tension equalizer bracket until the bracket is balanced. Securely tighten the lock nuts. 20 Engage the parking brake. B-11 Check the Wheel Bearings Mechanical Axle 21 Engage both drive motors. 22 Working from the front end of the parking brake cylinder, adjust the drive motor brake cables by hand until they have zero play and zero resistance. Be sure the brake cylinder balance bar is square to the parking brake input cable. 23 Disengage both drive motors. 24 Engage the parking brake. Attempt to move the machine in both directions. Result: The parking brake should prevent the machine from moving. If the parking brake does not prevent the machine from moving, repeat this procedure beginning with step 5. Axle specifications require that this procedure be performed quarterly or every 5000 km, whichever comes first. Proper axle maintenance, following the axle manufacturer's maintenance schedule, is essential to good axle performance and service life. Failure to perform the maintenance procedures can lead to poor axle performance and component damage. 1 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 2 Check for wheel bearing wear by attempting to move the wheel hub side to side, then up and down. Result: There should be no side to side or up and down movement. Result: There is side to side or up and down movement. See C-5, Grease the Axle Wheel Bearings - Mechanical Axle. Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). KNOTT Axle Service Manual Genie part number 3 - 24 Genie TZ-50 84443 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST B PROCEDURES 5 Lightly grease the ball mount. B-12 Service the Hitch Mechanical Axle 6 Confirm that the brake cable is securely installed into the brake handle linkage. 7 Apply the hand brake. 8 Attempt to manually push the machine. Axle specifications require that this procedure be performed quarterly or every 5000 km, whichever comes first. Proper axle maintenance, following the axle manufacturer's maintenance schedule, is essential to good axle performance and service life. Failure to perform the maintenance procedures can lead to poor axle performance and component damage. 1 Clean all visible surfaces of the ball coupler. 2 Lubricate the hitch at both grease fittings at the top of the over-run hitch. Result: The machine does not move. Result: The machine moves. Adjust the brakes. See Maintenance procedure C-6, Adjust the Brakes - Mechanical Axle. Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). KNOTT Axle Service Manual Genie part number 84443 3 Lubricate all bolts and articulated points on the hand brake lever using commonly available machine oil or motor oil. 4 Lubricate all bolts and movable parts of the coupler using commonly available machine oil or motor oil. Part No. 84577 Genie TZ-50 3 - 25 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST B PROCEDURES B-13 Perform Axle Maintenance Mechanical Axles B-14 Perform Engine Maintenance (if equipped) Axle specifications require that this procedure be performed annually or every 5000 km, whichever comes first. Engine specifications require that this procedure be performed every 300 hours or annually, whichever comes first. • Brake Inspection • Axle Inspection • Fuel tank and strainer • Valve clearance Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630) and the Honda GX160 Engine Shop Manual (Honda part number 61ZH700). KNOTT Axle Service Manual Genie part number 3 - 26 84443 Honda GX160 Owner's Manual Genie part number 97228 Honda GX160 Shop Manual Genie part number 97229 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures Checklist C Procedures C-1 Grease the Platform Overload Mechanism (if equipped) C-2 Test the Platform Overload System (if equipped) Genie specifications require that this procedure be performed every 500 hours or 6 months, whichever comes first. Perform this procedure more often if dusty conditions exist. Genie specifications require that this procedure be performed every 500 hours or 6 months, whichever comes first. Application of lubrication to the platform overload mechanism is essential to safe machine operation. Continued use of an improperly greased platform overload mechanism could result in the system not sensing an overloaded platform condition and will result in component damage. Testing the platform overload system regularly is essential to safe machine operation. Continued use of an improperly operating platform overload system could result in the system not sensing an overloaded platform condition. Machine stability could be compromised resulting in the machine tipping over. 1 Locate the grease fittings on each pivot pin of the platform overload assembly. Note: Perform this procedure with the machine on a firm, level surface. 2 Thoroughly pump grease into each grease fitting. 1 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. Grease type Multipurpose grease 2 Release the boom hold down latch. 3 Turn the key switch to platform control. 4 Level the platform. 5 Determine the maximum platform capacity. Refer to the machine serial plate. 6 Using a suitable lifting device, place an appropriate test weight equal to that of the maximum platform capacity in the center of the platform floor. Result: The platform overload indicator light should be off at both the ground and platform controls. Part No. 84577 Genie TZ-50 3 - 27 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST C PROCEDURES 7 Add an additional 44 lbs / 20 kg of weight to overload the platform. C-3 Perform Axle Maintenance Electrical and Hydraulic Axles Result: The platform overload indicator light should be flashing at both the ground and platform controls. 8 Test all machine functions from the platform controls. Result: All platform control functions should not operate. 9 Turn the key switch to ground control. Axle specifications require that this procedure be performed every 6 months or 6000 miles, whichever comes first. • Brake Magnets • Brake Controller • Suspension Components 10 Test all machine functions from the ground controls. Result: All ground control functions should not operate. 11 Lift the test weight off the platform floor using a suitable lifting device. Result: The platform overload indicator light should turn off at both the ground and platform controls. Required maintenance procedures and additional axle information is available in the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). Dexter Axle Operation Maintenance Service Manual Genie part number 84376 12 Test all machine functions from the ground controls. Result: All ground control functions should operate normally. 13 Turn the key switch to platform control. 14 Test all machine functions from the platform controls. Result: All platform control functions should operate. Note: If the platform overload system is not operating properly, refer to Repair Procedure 13-1, Calibrate the Platform Overload System (if equipped). 3 - 28 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST C PROCEDURES C-4 Replace the Hydraulic Tank Breather Cap Models with Optional Hydraulic Oil The hydraulic tank is a vented-type tank. The breather cap has an internal air filter that can become clogged or, over time, can deteriorate. If the breather cap is faulty or improperly installed, impurities can enter the hydraulic system which may cause component damage. Extremely dirty conditions may require that the cap be inspected more often. 1 Remove and discard the hydraulic tank breather cap. 2 Install a new cap onto the tank. C-5 Grease the Axle Wheel Bearings Mechanical Axle Axle specifications require that this procedure be performed every 6 months or 10,000 km, whichever comes first. Maintaining the axle wheel bearings is essential to safe operation and good machine performance. Towing the machine with loose or worn wheel bearings may cause an unsafe towing condition and continued use may result in component or property damage. Regular steam cleaning and pressure washing of the machine may require that this procedure be performed more often. 1 Loosen the wheel lug bolts. Do not remove them. 2 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 3 Remove the lug bolts and remove the tire and wheel assembly from the machine. 4 Remove, wash and inspect the axle wheel bearings and spacer ring. 5 Pack both bearings with clean, fresh grease. 6 Install the bearings and spacer ring onto the axle and reassemble the axle. Part No. 84577 Genie TZ-50 3 - 29 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST C PROCEDURES 7 Tighten the castle nut until the wheel runs with a little bite. 8 Loosen the castle nut just until the cotter pin fits into the next hole. Install a new cotter pin and lock into position. Install the dust cap. Note: Always replace the cotter pin with a new one when removing the castle nut or when checking the torque of the castle nut. 9 Install the tire and wheel onto the axle. Install and torque the lug bolts to specification. Refer to Section 2, Specifications. 10 Perform steps 3 through 9 for the other side of the machine. 11 Return the outriggers to the stowed position. Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). C-6 Adjust the Brakes Mechanical Axle Axle specifications require that this procedure be performed every 6 months or 10,000 km, whichever comes first. Proper axle maintenance, following the axle manufacturer's maintenance schedule, is essential to good axle performance and service life. Failure to perform the maintenance procedures can lead to poor axle performance and component damage. 1 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 2 Release the parking brake. KNOTT Axle Service Manual Genie part number 84443 3 Working from the exposed inside face of the brake plate, opposite the cable entry, tighten the adjusting screw until the wheel can only be turned with difficulty or not at all. Note: When tighten the adjusting screw, turn the wheel only in the direction of travel. 4 Ease off the adjusting screw approximately onehalf turn in a counterclockwise direction, until the wheel turns freely. 3 - 30 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST C PROCEDURES 5 Repeat steps 3 through 4 for the other brake. 6 Inspect the balance plate at the control cables. Result: The balance plate is at a right angle to the direction of towing. Result: The balance plate is not at a right angle to the direction of towing. Tighten or loosen the brake cable ends coming from the axle until the balance plate is at a right angle to the direction of towing. Note: The balance plate is located beneath the diamond plate cover in front of the turntable. 7 Return the outriggers to the stowed position. 8 Apply the parking brake. 9 Attempt to manually push the machine. Result: The machine does not move. Result: The machine moves. Repeat this procedure beginning with step 1. Result: One wheel rolls and the other one doesn’t. Repeat step 6 and adjust the balance plate to tighten the brake cable from the wheel which is rolling. Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). KNOTT Axle Service Manual Genie part number Part No. 84577 84443 Genie TZ-50 3 - 31 Section 3 • Scheduled Maintenance Procedures September 2014 Checklist D Procedures D-1 Perform Axle Maintenance Electric and Hydraulic Axles D-2 Check the Boom Wear Pads Axle specifications require that this procedure be performed every 12 months or 12,000 miles, whichever comes first. • Brake lining • Brake cylinders • Brake lines • Trailer brake wiring • Hub/Drum • Wheel bearings • Seals • Springs • Hangers Maintaining the boom wear pads in good condition is essential to safe machine operation. Wear pads are placed on boom tube surfaces to provide a low friction, replaceable wear pad between moving parts. Improperly shimmed wear pads or continued use of extremely worn wear pads may result in component damage and unsafe operating conditions. Note: If the wear pads are within specification, refer to Repair Procedure 3-2, How to Shim the Boom. 1 Extend the boom until the wear pads are accessible. Required maintenance procedures and additional axle information is available in the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). Dexter Axle Operation Maintenance Service Manual Genie part number 84376 2 Measure the thickness of the top, side and bottom wear pads. If the wear pad is within specification, shim as necessary to obtain zero clearance and zero drag. 3 Extend and retract the boom through the entire range of motion to check for tight spots that may cause binding or scraping of the boom. Note: Always maintain squareness between the outer and inner boom tubes. Boom wear pad specifications Wear pad thickness, minimum 3 - 32 Genie TZ-50 7/16 inch 11 mm Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST D PROCEDURES 3 Install the filter and tighten it securely by hand. D-3 Replace the Hydraulic Tank Return Filter 4 Use a permanent ink marker to write the date and number of hours from the hour meter on the new filter. Replacement of the hydraulic tank return filter element is essential for good machine performance and service life. A dirty or clogged filter element may cause the machine to perform poorly and continued use may cause component damage. Extremely dirty conditions may require that the filter element be replaced more often. 5 Clean up any oil that may have spilled during the replacement procedure. Properly discard the used filter. 6 Turn the key switch to ground controls and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 7 Raise the platform approximately 3 ft / 1 m. 8 Inspect the filter and related components to be sure that there are no leaks. Burn hazard. Beware of hot oil. Contact with hot oil may cause severe burns. Note: The hydraulic filter is mounted on the bulkhead next to the hydraulic tank. 1 Clean the area around the hydraulic oil filter. Remove the filter with an oil filter wrench. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 2 Apply a thin layer of fresh oil onto the gasket of the new oil filter. Part No. 84577 Genie TZ-50 3 - 33 Section 3 • Scheduled Maintenance Procedures September 2014 CHECKLIST D PROCEDURES 2 Working from underneath the turntable, be sure that each turntable rotation bearing mounting bolt is torqued in sequence to specification. Refer to Illustration 2. D-4 Check the Turntable Rotation Bearing Bolts Maintaining proper torque on the turntable bearing bolts is essential to safe machine operation. Improper bolt torque or torque sequence could result in an unsafe operating condition and component damage. Tongue 1 1 Be sure that each turntable rotation bearing mounting bolt above the turntable is torqued in sequence to specification. Refer to Illustration 1. 9 7 5 4 3 Tongue 6 2 8 9 5 1 Illustration 2 Bearing-to-chassis bolt torque sequence 11 3 Turntable rotation bearing bolt torque specifications 8 7 12 4 2 Bearing to chassis, lubricated 195 ft-lbs 264 Nm Bearing to swing chassis, lubricated 195 ft-lbs 264 Nm 6 10 Illustration 1 Bearing-to-swing chassis bolt torque sequence 3 - 34 Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST D PROCEDURES D-5 Inspect for Turntable Bearing Wear a b Periodic inspection of turntable bearing wear is essential to safe machine operation, good machine performance and service life. Continued use of a worn turntable bearing could create an unsafe operating condition, resulting in death or serious injury and component damage. c d a b c d Note: Perform this procedure with the machine on a firm, level surface and the boom in the stowed position. 1 Grease the turntable bearing. See A-13, Grease the Turntable Rotation Bearing and Rotate Gear. 2 Torque the turntable bearing bolts to specification. See D-2, Check the Turntable Rotation Bearing Bolts. 6 Lower the secondary boom to the stowed position and lower the primary boom to a horizontal position. Fully extend the primary boom. 7 Note the reading on the dial indicator. 3 Start the machine from the ground controls and raise the primary and secondary booms to full height. Do not extend the primary boom. 4 Place a dial indicator between the drive chassis and the turntable at a point that is directly under, or inline with, the boom and no more than 1 inch / 2.5 cm from the bearing. Note: To obtain an accurate measurement, place the dial indicator no more than 1 inch / 2.5 cm from the turntable rotation bearing. 5 At the dial indicator, adjust it to "zero" the indicator. turntable dial indicator drive chassis turntable rotation bearing Result: The measurement is less than 0.025 inch / 0.635 mm. The bearing is good. Result: The measurement is more than 0.025 inch / 0.635 mm. The bearing is worn and needs to be replaced. 8 Fully retract the primary boom. Raise the primary and secondary booms to full height. Visually inspect the dial indicator to be sure the needle returns to the "zero" position. 9 Remove the dial indicator and rotate the turntable 90°. 10 Repeat steps 4 through 9 until the rotation bearing has been checked in at least four equally spaced areas 90° apart. 11 Lower the primary and secondary booms to the stowed position and turn the machine off. 12 Remove the dial indicator from the machine. Part No. 84577 Genie TZ-50 3 - 35 Section 3 • Scheduled Maintenance Procedures September 2014 Checklist E Procedures E-1 Test or Replace the Hydraulic Oil Replacement or testing of the hydraulic oil is essential for good machine performance and service life. Dirty oil and suction strainers may cause the machine to perform poorly and continued use may cause component damage. Extremely dirty conditions may require oil changes to be performed more often. Note: Before replacing the hydraulic oil, the oil may be tested by an oil distributor for specific levels of contamination to verify that changing the oil is necessary. If the hydraulic oil is not replaced at the two year inspection, test the oil quarterly. Replace the oil when it fails the test. Note: When removing a hose assembly or fitting, the O-ring on the fitting and/or hose end must be replaced and then torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. Note: Perform this procedure with the machine in the stowed position. 1 Disconnect the battery pack from the machine. Electrocution hazard. Contact with hot or live circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 3 - 36 2 Remove the drain plug from the hydraulic tank and completely drain the tank into a suitable container. Refer to Section 2, Specifications, for capacity information. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 3 Tag and disconnect the hydraulic return line from the filter head to tank. 4 Tag and disconnect the hydraulic inlet line to the filter head. Cap the fitting on the line. 5 Remove the filter head from the machine. 6 Tag and disconnect the hydraulic line from the tank to the pump. Cap the fitting on the pump. 7 Remove the hydraulic tank mounting fasteners. Remove the hydraulic tank from the machine. 8 Clean the inside of the hydraulic tank using a mild solvent. 9 Install and tighten the hydraulic tank drain plug using thread sealer on the threads. Torque to specification. Torque specifications Hydraulic tank drain plug, dry 150 in-lbs 16.9 Nm Hydraulic tank drain plug, lubricated 112 in-lbs 12.6 Nm Genie TZ-50 Part No. 84577 September 2014 Section 3 • Scheduled Maintenance Procedures CHECKLIST E PROCEDURES 10 Install the hydraulic tank and install and tighten the hydraulic tank mounting fasteners. Torque to specification. E-2 Perform Engine Maintenance (if equipped) Torque specifications Hydraulic tank mounting fasteners, dry 35 in-lbs 4 Nm Hydraulic tank mounting fasteners, lubricated 26 in-lbs 2.9 Nm Engine specifications require that this procedure be performed every two years. • Fuel line 11 Install the hydraulic line onto the inlet side of the hydraulic pump. 12 Install the hydraulic filter head onto the machine and securely tighten the fasteners. Do not over tighten. Required maintenance procedures and additional engine information is available in the Honda GX160 Engine Shop Manual (Honda part number 61ZH700) Honda GX160 Shop Manual Genie part number 13 Install the hydraulic lines into the filter head. 97229 14 Connect the battery pack to the machine. 15 Fill the hydraulic tank with hydraulic oil until the fluid is at the FULL mark on the tank. Do not overfill. Refer to Section 2, Specifications. 16 Activate the pump to fill the hydraulic system with oil and bleed the system of air. Component damage hazard. The pump can be damaged if operated without oil. Be careful not to empty the hydraulic tank while in the process of filling the hydraulic system. 17 Repeat steps 15 through 16 until the hydraulic system and tank are both full. Inspect for leaks. 18 Clean up any oil that may have spilled. Part No. 84577 Genie TZ-50 3 - 37 Section 3 • Scheduled Maintenance Procedures September 2014 This page intentionally left blank. 3 - 38 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures Repair Procedures About This Section Most of the procedures in this section should only be performed by a trained service professional in a suitably equipped workshop. Select the appropriate repair procedure after troubleshooting the problem. Observe and Obey: Repair procedures shall be completed by a person trained and qualified on the repair of this machine. Perform disassembly procedures to the point where repairs can be completed. Then to re-assemble, perform the disassembly steps in reverse order. Symbols Legend Immediately tag and remove from service a damaged or malfunctioning machine. Safety alert symbol—used to alert personnel to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Repair any machine damage or malfunction before operating the machine. Before Repairs Start: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Read, understand and obey the safety rules and operating instructions in the appropriate Genie TZ-50 Operator's Manual on your machine. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Be sure that all necessary tools and parts are available and ready for use. Use only Genie approved replacement parts. Indicates a potentially hazardous situation which, if not avoided, may cause minor or moderate injury. Read each procedure completely and adhere to the instructions. Attempting shortcuts may produce hazardous conditions. Unless otherwise specified, perform each repair procedure with the machine in the following configuration: • Machine disconnected from tow vehicle • Machine parked on a firm, level surface • Boom in the stowed position with both latches secured • Key switch in the off position with the key removed Indicates a potentially hazardous situation which, if not avoided, may result in property damage. Indicates that a specific result is expected after performing a series of steps. Indicates that an incorrect result has occurred after performing a series of steps. • Wheels chocked • Parking brake applied Part No. 84577 Genie TZ-50 4-1 Section 4 • Repair Procedures September 2014 Platform Components 1-1 Platform 1-2 Platform Rotator How to Remove the Platform The platform rotator is a hydraulically-operated helical gear assembly used to rotate the platform 160°. 1 Tag and disconnect the taillight control cable at the front of the platform. 2 Remove the platform control box retaining fasteners. Remove the platform control box from the platform and set it to the side. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. How to Remove the Platform Rotator (if equipped) 1 Remove the platform. See 1-1, How to Remove the Platform. 2 Raise the jib boom 4 to 5 feet / 1.2 to 1.5 m. 3 Lower the jib boom until the platform mount rests on sawhorses or a work table of sufficient capacity. 3 Support and secure the platform to an appropriate lifting device. Do not apply any lifting pressure. 4 Remove the fasteners securing the platform to the lower side of the platform mount. 5 Remove the fasteners and pin securing the platform to the platform mount. Crushing hazard. The platform could become unbalanced and fall if not properly supported when the pin is removed. 4 Remove the wire harness from the platform mount. Set the platform controls and wire harness cables to the side. 5 Tag, disconnect and plug the hydraulic hoses to the platform rotator. Cap the fittings on the rotator. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 6 Remove the platform from the platform mount. 6 Attach a lifting strap of suitable capacity from an overhead crane to the platform mount. Support the mount. Do not apply any lifting pressure. 4-2 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures PLATFORM COMPONENTS 7 Remove the pin retaining fasteners securing the platform mount pivot pins. 8 Using a soft metal drift, remove the platform mount pivot pins. Remove the platform mount from the machine. Crushing hazard. The platform mount could fall if not properly supported when the pivot pin is removed. Part No. 84577 How to Bleed the Platform Rotator 1 Activate the platform rotate right function and rotate the platform completely to the right. Continue to activate the rotate right function for 3 seconds. 2 Activate the platform rotate left function and rotate the platform completely to the left. Continue to activate the rotate left function for 3 seconds. Genie TZ-50 4-3 Section 4 • Repair Procedures September 2014 Jib Boom Components 2-1 Jib Boom a b c d e f g h i j The jib boom lift cylinder raises and lowers the jib boom. The jib boom lift cylinder is equipped with a counterbalance valve to prevent movement in the event of a hydraulic line failure. How to Remove the Jib Boom Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. a b c d e f g h i j 1 Remove the platform. See 1-1, How to Remove the Platform. 2 Raise the jib boom 4 to 5 feet / 1.2 to 1.5 m. 3 Lower the jib boom until the platform mount rests on sawhorses or a work table of sufficient capacity. 4 Tag and disconnect the wire harness from the platform control box. 5 Tag and disconnect the wires from the jib manifold. 8 Tag, disconnect and plug the hydraulic hoses to the platform rotator. Cap the fittings on the rotator. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 6 Remove the wire harness from the platform mount and the jib boom. 7 Pull the all harness cables through the jib boom and lay them off to the side of the primary boom. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. 4-4 platform mount jib boom cylinder barrel-end pivot pin jib link pivot pin jib link jib boom lift cylinder jib boom jib boom cylinder rod-end pivot pin jib boom pivot pin jib mount pivot pin platform level slave cylinder rod end pivot pin 9 Tag, disconnect and plug the hydraulic hoses to the jib cylinder. Cap the fittings on the cylinder. Genie TZ-50 Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Part No. 84577 September 2014 Section 4 • Repair Procedures JIB BOOM COMPONENTS 10 Attach a lifting strap of suitable capacity from an overhead crane to the platform mount. Support the mount. Do not apply any lifting pressure. 11 Remove the pin retaining fasteners securing the platform mount pivot pins. 12 Using a soft metal drift, remove the platform mount pivot pins. Remove the platform mount from the machine. Crushing hazard. The platform mount could fall if not properly supported when the pivot pin is removed. 13 Remove the jib manifold retaining fasteners. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. 14 Attach a lifting strap of suitable capacity from an overhead crane to the jib boom. Support the jib boom. Do not apply any lifting pressure. 15 Remove the pin retaining fasteners securing the jib boom pivot pins. 16 Using a soft metal drift, remove the jib boom pivot pins. Remove the jib boom from the machine. Crushing hazard. The platform mount could fall if not properly supported when the pivot pin is removed. 17 Lay the jib manifold and hoses off to the side of the primary boom. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. Part No. 84577 18 Attach a lifting strap of suitable capacity from an overhead crane to the jib link at the ground control side of the machine. Support the jib link. Do not apply any lifting pressure. 19 Working from the ground control side of the machine, use a soft metal drift to tap the jib link pivot pin halfway out. Remove the jib link from the machine. Crushing hazard. The jib link could fall if not properly supported when the pivot pin is removed. 20 Attach a lifting strap of suitable capacity from an overhead crane to the remaining jib link. Support the jib link. Do not apply any lifting pressure. 21 Working from the side of the machine opposite the ground controls, use a soft metal drift to tap the jib link pivot pin halfway out. Remove the jib link from the machine. Crushing hazard. The jib link could fall if not properly supported when the pivot pin is removed. 22 Attach a lifting strap of suitable capacity from an overhead crane to the jib cylinder. Support the cylinder. Do not apply any lifting pressure. 23 Using a soft metal drift, remove the jib cylinder pivot pin. Remove the cylinder from the machine. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 24 Attach a lifting strap of suitable capacity from an overhead crane to the jib mount. Support the mount. Do not apply any lifting pressure. Genie TZ-50 4-5 Section 4 • Repair Procedures September 2014 JIB BOOM COMPONENTS 25 Remove the pin retaining fasteners securing the jib mount pivot pin and the platform level slave cylinder rod end pivot pin. 2-2 Jib Boom Lift Cylinder 26 Place a wooden block between the primary boom and the platform level slave cylinder. How to Remove the Jib Boom Lift Cylinder 27 Using a soft metal drift, remove the platform level slave cylinder rod end pivot pin. Rest the cylinder on the block. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 28 Using a soft metal drift, remove the jib mount pivot pin. Remove the jib mount from the machine. Crushing hazard. The jib mount could fall if not properly supported when the pivot pin is removed. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Raise the jib boom 4 to 5 feet / 1.2 to 1.5 m. 2 Lower the jib boom until the platform mount rests on sawhorses or a work table of sufficient capacity. 3 Tag, disconnect and plug the hydraulic hoses to the jib cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 Attach a lifting strap of suitable capacity from an overhead crane to the platform mount. Support the mount. Do not apply any lifting pressure. 5 Attach a lifting strap of suitable capacity from an overhead crane to the jib boom. Support the jib boom. Do not apply any lifting pressure. 4-6 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures JIB BOOM COMPONENTS 6 Place a wooden block between the jib cylinder and the jib links. 7 Remove the pin retaining fasteners securing the jib boom cylinder barrel end pivot pin. 8 Using a soft metal drift, remove the jib boom cylinder barrel end pivot pin. Lower the cylinder onto the wooden block. Crushing hazard. The jib cylinder could fall if not properly supported when the pivot pin is removed. Crushing hazard. The jib boom could fall if not properly supported when the pivot pin is removed. 9 Install the jib boom onto the platform mount. Install the pivot pin securing the jib boom to the platform mount. 10 Attach a lifting strap of suitable capacity from an overhead crane to the jib link at the ground control side of the machine. Support the jib link. Do not apply any lifting pressure. 11 Working from the ground control side of the machine, use a soft metal drift to tap the jib link pivot pin halfway out. Lower the jib link. Crushing hazard. The jib link could fall if not properly supported when the pivot pin is removed. 12 Working from the ground control side of the machine, use a soft metal drift to tap the jib link pivot pin out just enough to release the jib cylinder. Remove the cylinder from the machine. Crushing hazard. The jib cylinder could fall if not properly supported when the pivot pin is removed. Part No. 84577 Genie TZ-50 4-7 Section 4 • Repair Procedures September 2014 Primary Boom Components e g f h j i k l m d c b a a b c d e f g h i j k l mid-pivot primary boom lift cylinder barrel-end pivot pin platform level master cylinder primary boom pivot pin platform level master cylinder rod-end pivot pin extension cylinder barrel-end pivot pin primary boom lift cylinder primary boom lift cylinder rod-end pivot pin primary boom primary boom latch extension boom platform level slave cylinder m n o p q r s t u v w jib boom secondary boom pivot pin secondary boom link pivot pin secondary boom latch secondary boom secondary boom link secondary lift cylinder rod-end pivot pin secondary boom lift cylinder secondary lift cylinder barrel-end pivot pin (located behind ground control box) turntable secondary boom pivot pin a n o p w 4-8 v u t s Genie TZ-50 r q Part No. 84577 September 2014 Section 4 • Repair Procedures PRIMARY BOOM COMPONENTS 3-1 Cable Track The boom cable track guides cables and hoses running up the boom. It can be repaired link by link without removing the cables and hoses that run through it. Removing the entire boom cable track may be necessary when performing major repairs that involve removing the boom. 5 Tag, disconnect and plug the hydraulic hoses at the jib boom end of the cable bridge. Cap the fittings on the hydraulic hard lines. Refer to 'XX' in the illustration below. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. How to Remove the Cable Track Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Tag and disconnect the wire harness from the platform control box. XX a YY f 2 Tag and disconnect the wires from the jib manifold. e d a b c d e f 3 Remove the wire harness from the platform mount and the jib boom. 4 Pull the all harness cables through the jib boom and lay them off to the side of the primary boom. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. c b extension boom cable bridge cable track track support platform level slave cylinder jib boom 6 Tag, disconnect and plug the hydraulic hoses at the lower end of the cable track. Cap the fittings on the hydraulic hard lines. Refer to 'YY' in the illustration above. 7 Place blocks between the cable bridge and the cable track and secure them together. Crushing hazard. If the cable bridge and the cable track are not properly secured together, the combination could become unbalanced and fall when removed from the machine. Part No. 84577 Genie TZ-50 4-9 Section 4 • Repair Procedures September 2014 PRIMARY BOOM COMPONENTS 8 Attach a lifting strap of suitable capacity from an overhead crane to the rod end of the primary lift cylinder. Support the cylinder. Do not apply any lifting pressure. 9 Remove the pin retaining fastener from the primary lift cylinder rod end pivot pin. 10 Using a soft metal drift, remove the primary lift cylinder rod end pivot pin. Crushing hazard. The cylinder will fall if not properly supported when the pivot pin is removed. 11 Lower the cylinder onto the secondary boom. 12 Remove the wire harness cables from the bottom of the primary boom. Secure the hydraulic hard lines to the boom. 13 Place blocks between the cable bridge and the cable track. Secure the cable bridge and the cable track together. Crushing hazard. If the cable bridge and the cable track are not properly secured together, the combination could become unbalanced and fall when removed from the machine. 14 Attach a lifting strap from an overhead crane to the cable track. 15 Remove the mounting fasteners that attach the lower cable track to the boom. 16 Remove the cable track from the machine and place it on a structure capable of supporting it. Crushing hazard. The cable track could become unbalanced and fall if not properly attached to the overhead crane. 4 - 10 How to Repair the Cable Track Component damage hazard. The cable track can be damaged if it is twisted. 1 Visually inspect the cable track and determine which 7 link section needs to be replaced. 2 Using a flat blade screwdriver, pry open the hinge bar on each link of the 7 link section, plus one more on each end making a total of 9. 3 Using a flat blade screwdriver at one side of the link to be replaced, separate the connection and open the joint slightly by sliding the link over the link pivot. Repeat for the other side of the link to separate the link sections. 4 Repeat step 3 for the other end of the section to be replaced. 5 Lift up the hoses and cables and carefully remove the damaged section of cable track. Component damage hazard. Hoses and cables can be damaged if they are kinked or pinched. 6 Lift up the hoses and cables and carefully insert the new section of cable track. 7 Install the new section of cable track onto the existing track. Be sure the link pivot on both sides of the link are in place and that the track hinges correctly 8 Securely lock the hinge bar for each link. 9 Operate the boom extend/retract function through a full cycle to ensure smooth operation of the new section of cable track. Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures PRIMARY BOOM COMPONENTS 3-2 Primary Boom How to Remove the Primary Boom This procedure requires specific repair skills, lifting equipment and a suitable workshop. Attempting this procedure without these skills and tools could result in death or serious injury and significant component damage. Dealer service is required. How to Shim the Primary Boom 1 Extend the boom until the wear pads are accessible. 2 Loosen the wear pad mounting fasteners. 3 Install the new shims under the wear pad to obtain zero clearance and zero drag. 4 Securely tighten the mounting fasteners. Do not over tighten. 5 Extend and retract the boom through an entire cycle. Check for tight spots that could cause binding or scraping. Note: Always maintain squareness between the outer and inner boom tubes. Follow the disassembly steps to the point required to complete the repair. Then re-assemble the secondary boom by following the disassembly steps in reverse order. Note: When removing a hose assembly or fitting, the O-ring on the fitting and/or hose end must be replaced and then torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Remove the platform. See 1-1, How to Remove the Platform. 2 Remove the jib boom. See 2-1, How to Remove the Jib Boom. 3 Remove the wire harness cables from the bottom of the secondary boom. Secure the hydraulic hard lines to the boom. 4 Tag and disconnect the wire harness cables from the ground controls. Pull the cables to the mid pivot. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. Note:For ease of assembly, pay close attention to how the cables are routed when pulling the cables to the mid pivot. Part No. 84577 Genie TZ-50 4 - 11 Section 4 • Repair Procedures September 2014 PRIMARY BOOM COMPONENTS 5 Remove the harness clamps inside the mid pivot. Pull the wire harness cables through the mid pivot and lay them off to the side of the primary boom. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. 6 Tag, disconnect and plug the hoses from the platform level master cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 7 Tag, disconnect and plug the hoses from the primary boom extension cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 8 Attach a lifting strap of suitable capacity from an overhead crane to the rod end of the primary lift cylinder. Support the cylinder. Do not apply any lifting pressure. 10 Using a soft metal drift, remove the primary lift cylinder rod end pivot pin. Crushing hazard. The cylinder will fall if not properly supported when the pivot pin is removed. 11 Lower the cylinder onto the secondary boom. 12 Remove the pin retaining fastener from the platform level master cylinder rod end pivot pin. 13 Using a soft metal drift, remove the platform level master cylinder rod end pivot pin. 14 Attach a lifting strap of suitable capacity from an overhead crane to the primary boom. Support the boom. Do not apply any lifting pressure. Component damage hazard. The cable track can be damaged if not protected when lifting the boom. 15 Remove the pin retaining fasteners securing the primary boom pivot pin. 16 Using a soft metal drift, remove the primary boom pivot pin. Crushing hazard. The primary boom could become unbalanced and fall if not properly supported when the pin is removed. 17 Release the latch at the turntable end of the machine. 18 Remove the primary boom from the machine. 9 Remove the pin retaining fastener from the primary lift cylinder rod end pivot pin. 4 - 12 Genie TZ-50 Crushing hazard. The primary boom could become unbalanced and fall if not properly supported when removed from the machine. Part No. 84577 September 2014 Section 4 • Repair Procedures PRIMARY BOOM COMPONENTS 7 Remove the pin retaining fastener from the platform level slave cylinder barrel-end pivot pin. How to Remove the Boom Extension This procedure in this section requires specific repair skills, lifting equipment and a suitable workshop. Attempting this procedure without these skills and tools could result in death or serious injury and significant component damage. Dealer service is required. Follow the disassembly steps to the point required to complete the repair. Then re-assemble the secondary boom by following the disassembly steps in reverse order. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Remove the platform. See 1-1, How to Remove the Platform. 2 Remove the jib boom. See 2-1, How to Remove the Jib Boom. 3 Remove the primary boom. See 3-2, How to Remove the Boom. 4 Set the primary boom assembly on a suitable structure capable of supporting it. 5 Place a block between the platform level slave cylinder and the extension boom. 6 Remove the fasteners and hose clamp securing the platform level slave cylinder hoses to the extension boom. Part No. 84577 8 Using a soft metal drift, remove the platform level slave cylinder barrel-end pivot pin. 9 Tag, disconnect and plug the hoses from the platform level slave cylinder. Cap the fittings on the cylinder. 10 Remove the platform level slave cylinder from the boom. 11 Remove the primary boom upper wear pad retaining fasteners. Remove the upper wear pads from the primary boom. 12 Remove the primary boom side wear pad retaining fasteners. Remove the side wear pads and shims from the primary boom. Note: For ease of assembly, note the quantity and location of shims during disassembly. 13 Remove the primary boom lower wear pad retaining fasteners. Remove the lower wear pads from the primary boom. 14 Remove the pin retaining fastener from the primary boom extension cylinder barrel-end pivot pin. 15 Using a soft metal drift, remove the primary boom extension cylinder barrel-end pivot pin. 16 Remove the boom extension from the primary boom. 17 Remove the pin retaining fasteners from the primary boom extension cylinder rod-end pivot pins. 18 Using a soft metal drift, remove the primary boom extension cylinder rod-end pivot pins. 19 Remove the primary boom extension cylinder from the boom extension. Genie TZ-50 4 - 13 Section 4 • Repair Procedures September 2014 PRIMARY BOOM COMPONENTS 3-3 Primary Boom Lift Cylinder 5 Lower the cylinder onto the secondary boom. How to Remove the Primary Boom Lift Cylinder 7 Using a soft metal drift, remove the lift cylinder barrel end pivot pin. 6 Remove the pin retaining fastener from the lift cylinder barrel end pivot pin. The primary boom lift cylinder raises and lowers the primary boom. The primary boom lift cylinder is equipped with a counterbalance valve to prevent movement in the event of a hydraulic line failure. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 8 Carefully remove the cylinder from the machine. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. Crushing hazard. The lift cylinder could become unbalanced and fall if not properly supported when removed from the machine. 1 Tag, disconnect and plug the hydraulic hoses on the lift cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 2 Attach a lifting strap of suitable capacity from an overhead crane to the lift cylinder. 3 Remove the pin retaining fastener from the lift cylinder rod end pivot pin. 4 Using a soft metal drift, remove the lift cylinder rod end pivot pin. Crushing hazard. The cylinder will fall if not properly supported when the pivot pin is removed. 4 - 14 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures PRIMARY BOOM COMPONENTS 3-4 Platform Leveling Cylinders a b How to Remove the Master Cylinder The master cylinder, located inside the mid pivot, acts as a pump for the slave cylinder, which is located at the platform end of the extension boom. The master cylinder operates in a closed-circuit hydraulic loop with the slave cylinder, keeping the platform level through the entire range of boom motion. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Tag, disconnect and plug the master cylinder hydraulic hoses. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Part No. 84577 a b platform level master cylinder platform level slave cylinder 2 Remove the pin retaining fastener from the master cylinder barrel end pivot pin. 3 Using a soft metal drift, remove the master cylinder barrel end pivot pin. 4 Attach a lifting strap from an overhead crane to the lug on the rod end of the master cylinder. 5 Remove the pin retaining fastener from the rod end pivot pin. 6 Using a soft metal drift, remove the master cylinder rod end pivot pin. Remove the master cylinder from the machine. Genie TZ-50 Crushing hazard. The master cylinder could become unbalanced and fall if not properly supported when removed from the machine 4 - 15 Section 4 • Repair Procedures September 2014 PRIMARY BOOM COMPONENTS How to Remove the Slave Cylinder a The slave cylinder, via a closed-circuit hydraulic loop, works in tandem with the master cylinder to maintain the platform in a level condition through the entire range of boom motion. The slave cylinder, located at the platform end of the extension boom, is equipped with counterbalance valves to prevent movement in the event of a hydraulic line failure. b a b platform level master cylinder platform level slave cylinder Before cylinder removal is considered to correct a malfunction, bleed the slave cylinder to be sure there is no air in the closed loop hydraulic circuit. 3 Remove the pin retaining fastener from the slave cylinder rod end pivot pin. Do not remove the pin. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 4 Remove the external retaining rings from the barrel end pivot pin. 5 Using a soft metal drift, remove the rod end pivot pin. 6 Carefully pull the cylinder out of the boom. Component damage hazard. Hoses can be damaged if they are kinked or pinched. 1 Extend the boom approximately 12 inches / 30 cm. 2 Tag, disconnect and plug the slave cylinder hydraulic hoses from the tee fittings on the jib manifold, and connect them together using a connector. Cap the fittings on the manifold. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 - 16 How to Bleed the Slave Cylinder 1 Raise the boom to a horizontal position. 2 Activate the platform level function in both up and down directions through two complete platform leveling cycles to remove any air that might be in the system. The master cylinder acts as a pump for the slave cylinder. It is part of the closed loop hydraulic circuit that keeps the platform level through the entire range of boom motion. The master cylinder is located inside the mid pivot. Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures This page intentionally left blank. Part No. 84577 Genie TZ-50 4 - 17 Section 4 • Repair Procedures September 2014 Secondary Boom Components e g f h j i k l m d c b a a b c d e f g h i j k l mid-pivot primary boom lift cylinder barrel-end pivot pin platform level master cylinder primary boom pivot pin platform level master cylinder rod-end pivot pin extension cylinder barrel-end pivot pin primary boom lift cylinder primary boom lift cylinder rod-end pivot pin primary boom primary boom latch extension boom platform level slave cylinder m n o p q r s t u v w jib boom secondary boom pivot pin secondary boom link pivot pin secondary boom latch secondary boom secondary boom link secondary lift cylinder rod-end pivot pin secondary boom lift cylinder secondary lift cylinder barrel-end pivot pin (located behind ground control box) turntable secondary boom pivot pin a n o p w 4 - 18 v u t s Genie TZ-50 r q Part No. 84577 September 2014 Section 4 • Repair Procedures SECONDARY BOOM COMPONENTS 5 Remove the pin retaining fasteners securing the primary lift cylinder barrel end pivot pin. 4-1 Secondary Boom 6 Using a soft metal drift, remove the primary lift cylinder barrel end pivot pin. Remove the cylinder from the machine. How to Remove the Secondary Boom This procedure requires specific repair skills, lifting equipment and a suitable workshop. Attempting this procedure without these skills and tools could result in death or serious injury and significant component damage. Dealer service is required. Follow the disassembly steps to the point required to complete the repair. Then re-assemble the secondary boom by following the disassembly steps in reverse order. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 7 Attach a lifting strap of suitable capacity from an overhead crane to the mid-pivot. Support the mid pivot. Do not apply any lifting pressure. 8 Remove the pin retaining fasteners securing the secondary boom pivot pin at the mid-pivot. 9 Remove the pin retaining fasteners securing the secondary link pivot pin at the mid-pivot. 10 Tag, disconnect and plug the hydraulic hoses to the hydraulic hard lines at the mid-pivot end of the secondary boom. Cap the fittings. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 1 Remove the platform. See 1-1, How to Remove the Platform. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. 2 Remove the jib boom. See 2-1, How to Remove the Jib Boom. 3 Remove the primary boom. See 3-2, How to Remove the Primary Boom. 11 Using a soft metal drift, remove the secondary boom pivot pin at the mid-pivot. Remove the mid-pivot 4 Attach a lifting strap of suitable capacity from an overhead crane to the rod end of the primary lift cylinder. Raise the cylinder to a horizontal position. Part No. 84577 Genie TZ-50 Crushing hazard. The mid-pivot could become unbalanced and fall if not properly supported when the pin is removed. 4 - 19 Section 4 • Repair Procedures September 2014 SECONDARY BOOM COMPONENTS 12 Using a soft metal drift, remove the secondary link pivot pin at the mid-pivot. Crushing hazard. The secondary link could become unbalanced and fall if not properly supported when the pin is removed. 20 Tag, disconnect and plug the hydraulic hoses to the hydraulic hard lines at the turntable end of the secondary boom. Cap the fittings. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 13 Remove the mid-pivot from the machine. Crushing hazard. The mid-pivot could become unbalanced and fall if not properly supported when removed from the machine. Component damage hazard. Cables and hoses can be damaged if they are kinked or pinched. Remove the secondary boom 14 Attach a lifting strap of suitable capacity from an overhead crane to the secondary boom. Support the secondary boom. Do not apply any lifting pressure. 21 Remove the pin retaining fasteners securing the secondary boom pivot pin to the turntable. 22 Using a soft metal drift, remove the secondary boom pivot pin. 15 Remove the pin retaining fasteners securing the lift cylinder pivot pin to the secondary boom. Crushing hazard. The secondary boom could become unbalanced and fall if not properly supported when the pin is removed. 16 Place a wooden block between the secondary link and the secondary lift cylinder. 17 Using a soft metal drift, remove the lift cylinder pivot pin from the secondary boom. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 18 Lower the cylinder onto the wooden block. 19 Raise the secondary boom to a horizontal position. 23 Remove the secondary boom from the machine. Remove the secondary link 24 Working at the ground controls, remove the power to platform wiring from the ground control box. 25 Remove the ground controls from the machine. 26 Rotate the rod end of the secondary boom lift cylinder approximately 90°. 27 Attach a lifting strap of suitable capacity from an overhead crane to the rod end of the lift cylinder. Raise the cylinder slightly, remove the block and lower the cylinder through the secondary link and onto the front bulkhead. 4 - 20 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures SECONDARY BOOM COMPONENTS 28 Remove the pin retaining fasteners securing the secondary link pivot pin to the turntable. 29 Using a soft metal drift, remove the secondary link pivot pin. Crushing hazard. The secondary link could become unbalanced and fall if not properly supported when the pin is removed. 4-2 Secondary Boom Lift Cylinder The secondary boom lift cylinder raises and lowers the secondary boom. The secondary boom lift cylinder is equipped with a counterbalance valve to prevent movement in the event of a hydraulic line failure. 30 Release the latch at the tongue end of the machine. 1 Release the boom latch at both the tongue end and turntable end of the boom. 31 Remove the secondary link from the machine. 2 Raise the secondary boom to a horizontal position. Crushing hazard. The secondary link could become unbalanced and fall if not properly supported when removed from the machine. 3 Attach a lifting strap of suitable capacity from an overhead crane to the mid-pivot. Support the mid-pivot. Do not apply any lifting pressure. 32 Tag, disconnect and plug the hoses from the secondary lift cylinder. Cap the fittings on the cylinder. 4 Attach a lifting strap of suitable capacity from an overhead crane to the lift cylinder. Support the cylinder. Do not apply any lifting pressure. 33 Attach a lifting strap of suitable capacity from an overhead crane to the secondary lift cylinder. Raise the cylinder to a horizontal position. 5 Remove the pin retaining fasteners securing the lift cylinder rod end pivot pin. 34 Remove the pin retaining fasteners securing the secondary lift cylinder pivot pin to the mid-pivot. 35 Using a soft metal drift, remove the secondary lift cylinder pivot pin. Remove the cylinder from the machine. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 6 Place a wooden block between the secondary link and the lift cylinder. 7 Using a soft metal drift, remove the lift cylinder pivot pin. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 8 Lower the cylinder onto the wooden block. 9 Rotate the rod end of the secondary boom lift cylinder approximately 90°. 10 Raise the cylinder slightly, remove the block and lower the cylinder through the secondary link and onto the front bulkhead. Part No. 84577 Genie TZ-50 4 - 21 Section 4 • Repair Procedures September 2014 SECONDARY BOOM COMPONENTS 11 Tag, disconnect and plug the hydraulic hoses on the lift cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Note: Place rags beneath the barrel end of the lift cylinder before loosening the hydraulic lines. Note: It may be helpful to remove the turntable rotate motor. 12 Remove the pin retaining fasteners securing the lift cylinder barrel end pivot pin. 13 Using a soft metal drift, remove the lift cylinder barrel end pivot pin. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed. 14 Carefully remove the cylinder from the machine. Crushing hazard. The lift cylinder could become unbalanced and fall if not properly supported when removed from the machine. 4 - 22 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures Engine 5-1 Fuse Replacement The electric engine starter circuit is protected by both a 5 amp and 50 amp fuse. If either fuse burns out, the electric starter will not operate. The engine can, however, still be manually started. Additional engine information is available in the Honda GX160 Engine Owner Manual (Honda part number 31ZH7630) OR the Honda Engines Shop Manual (Honda part number 61ZH700). Honda GX160 Owner's Manual Genie part number 97228 Honda Engines Shop Manual Genie part number 97229 a c b a b c Part No. 84577 5 amp fuse - starter circuit (inside cover) 50 amp fuse - starter circuit 50 amp fuse - alternator circuit Genie TZ-50 4 - 23 Section 4 • Repair Procedures September 2014 Ground Controls 3 Push and hold the yellow function enable button. Push and hold the auto level button. 6-1 Level Sensor Each machine is equipped with two types of level sensors: Tilt level sensor One level sensor monitors the incline of the turntable after the outriggers are deployed and the machine is level. When this level sensor activates, an alarm will sound, making the operator aware of a potentially hazardous situation. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. Use the bubble level located below the ground controls to confirm that the machine is level. 4 Turn the key switch to the off position. 5 Locate the tilt level sensor beneath the ground control panel. Refer to the following illustrations. a b c b The tilt alarm sounds when the incline of the chassis exceeds 2.5° in any direction. CR66 Outrigger auto level system When deploying the outriggers using the autolevel function, outrigger level sensors are used to monitor the incline of the turntable and assist in leveling the machine. AUTO LEVEL RELAY Y X Y Y In early production, two level sensors are components of the outrigger auto level circuit. Later in production, a single autolevel module was used. How to Install and Calibrate the Tilt Level Level Sensor Tip-over hazard. Failure to install or calibrate the level sensor as instructed could result in the machine tipping over causing death or serious injury. Do not install or calibrate the level sensor other than specified in this procedure. 1 Perform this procedure with the machine on a firm, level surface that is free of obstructions. 2 Turn the key switch to ground control and pull out the red Emergency Stop buttons to the on position at both the ground and platform controls. 4 - 24 X X d d a b c d e e d tilt level sensor outrigger level sensor autolevel relay (early production) "X" indicator adjusting fastener If you are not installing a new level sensor, proceed to step 10. Install the level sensor: 6 Tag and disconnect the wire harness from the tilt level sensor. 7 Remove the three level sensor retaining fasteners. Remove the level sensor from the machine. Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures GROUND CONTROLS 8 Install the new level sensor onto the machine with the "X" on the level sensor housing located as shown in the illustrations. Install and tighten the level sensor retaining fasteners. 9 Connect the wire harness to the level sensor. 10 Tighten the level sensor adjusting fasteners until the bubble in the top of the level sensor is centered in the circles. Note: Be sure there are threads showing through the top of the adjusting fasteners. 11 Turn the key switch to ground control and pull out the red Emergency Stop buttons to the on position at both the ground and platform controls. 12 Raise the secondary boom approximately 12 inches / 30 cm. Result: The tilt sensor alarm should not sound. 13 Using a digital level, lower the tank side of the machine until the turntable is 2.4° out of level. Result: The tilt sensor alarm should not sound. Result: The tilt alarm will sound at 180 beeps per minute. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 14 Continue to lower the tank side of the machine until the turntable is 2.7° out of level. Result: The tilt alarm will sound at 180 beeps per minute. Result: The tilt alarm does not sound. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 15 Push and hold the yellow function enable button. Push and hold the auto level button. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. Use the bubble level located below the ground controls to confirm that the machine is level. 16 Using a digital level, lower the ground control side of the machine until the turntable is 2.4° out of level. Result: The tilt sensor alarm should not sound. Result: The tilt alarm will sound at 180 beeps per minute. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 17 Continue to lower the ground control side of the machine until the turntable is 2.7° out of level. Result: The tilt alarm will sound at 180 beeps per minute. Result: The tilt alarm does not sound. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 18 Push and hold the yellow function enable button. Push and hold the auto level button. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. Use the bubble level located below the ground controls to confirm that the machine is level. 19 Using a digital level, lower the platform end of the machine until the turntable is 2.4° out of level. Result: The tilt sensor alarm should not sound. Result: The tilt alarm will sound at 180 beeps per minute. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. Part No. 84577 Genie TZ-50 4 - 25 Section 4 • Repair Procedures September 2014 GROUND CONTROLS 20 Continue to lower the platform end of the machine until the turntable is 2.7° out of level. How to Install and Calibrate the Outrigger Level Sensor Result: The tilt alarm will sound at 180 beeps per minute. Tip-over hazard. Failure to install or calibrate the level sensor as instructed could result in the machine tipping over causing death or serious injury. Do not install or calibrate the level sensor other than specified in this procedure. Result: The tilt alarm does not sound. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 21 Push and hold the yellow function enable button. Push and hold the auto level button. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. Use the bubble level located below the ground controls to confirm that the machine is level. 22 Using a digital level, lower the tongue end of the machine until the turntable is 2.4° out of level. Result: The tilt sensor alarm should not sound. Result: The tilt alarm will sound at 180 beeps per minute. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 1 Perform this procedure with the machine on a firm, level surface that is free of obstructions. 2 Turn the key switch to ground control and pull out the red Emergency Stop buttons to the on position at both the ground and platform controls. 3 Lower all four outriggers and raise the machine off the ground. Level the machine. Use the bubble level located below the ground controls to confirm that the machine is level. 4 Turn the key switch to the off position. 23 Continue to lower the tongue end of the machine until the turntable is 2.7° out of level. Result: The tilt alarm will sound at 180 beeps per minute. Result: The tilt alarm does not sound. The level sensor is faulty and must be replaced. Repeat this procedure beginning with step 6. 24 Return the outriggers to the stowed position. 4 - 26 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures GROUND CONTROLS 5 Locate the outrigger level sensors located below the ground control panel. Refer to the following illustrations. a b c b AUTO LEVEL RELAY 8 Install the new level sensor onto the machine with the "X" on the level sensor housing located as shown in the illustrations. Install and tighten the level sensor retaining fasteners. X Y Y X 9 Connect the wire harness to the level sensor. X d 10 Tighten the level sensor adjusting fasteners until the bubble in the top of the level sensor is centered in the circles. d a b c d e 6 Tag and disconnect the wire harness from the outrigger level sensor. 7 Remove the three level sensor retaining fasteners. Remove the level sensor from the machine. CR66 Y If you are not installing a new level sensor, proceed to step 10. e d tilt level sensor outrigger level sensor autolevel relay (early production) "X" indicator adjusting fastener a Note: Be sure there are threads showing through the top of the adjusting fasteners. 11 Turn the key switch to ground control. 12 Raise the outriggers until all of the outriggers are off the ground. 13 Push and hold the yellow function enable button. Push and hold the auto level button. b Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. Use the bubble level located below the ground controls to confirm that the machine is level. Y X Y X d Part No. 84577 e d Genie TZ-50 4 - 27 Section 4 • Repair Procedures September 2014 Hydraulic Pump 4 Activate the platform up function from the ground controls. 7-1 Function Pump Result: If the pressure gauge reads 3200 psi / 221 bar, immediately stop. The pump is good. The hydraulic pumps are attached to the motor which makes up the hydraulic power unit. How to Test the Hydraulic Pump Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. Result: If pressure fails to reach 3200 psi / 221 bar, the pump is bad and will need to be serviced or replaced. Component damage hazard. There is no relief valve in the hydraulic pump and the pump can be damaged if the pressure is allowed to exceed 3200 psi / 221 bar. When testing the pump, activate the pump in one second intervals until 3200 psi / 221 bar is confirmed. Do not over-pressurize the pump. 1 Tag, disconnect and plug the high pressure hydraulic hose from the hydraulic pump. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 5 Remove the pressure gauge and reconnect the hydraulic hose. Torque to specification. 2 Connect a 0 to 5000 psi / 0 to 350 bar pressure gauge to the high pressure port on the pump. 3 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 4 - 28 Genie TZ-50 Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Part No. 84577 September 2014 Section 4 • Repair Procedures HYDRAULIC PUMP 7 Remove the pump mounting bolts. Carefully remove the pump. How to Remove the Hydraulic Pump Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Disconnect the battery pack from the machine. Tip-over hazard. After replacing the hydraulic pump, it is critical to return the function speed settings to original factory specifications. Failure to restore the machine to original factory specifications could cause the machine to tip over resulting in death or serious injury. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 2 Tag and disconnect the hydraulic power unit cables at the motor controller. 3 Remove the hydraulic power unit retaining fasteners. 5 Tag, disconnect and plug the hydraulic hard line at the pump. Cap the fitting on the pump. 6 Tag, disconnect and plug the high pressure hose at the pump. Cap the fitting on the pump. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Part No. 84577 Genie TZ-50 4 - 29 Section 4 • Repair Procedures September 2014 Manifolds 8-1 Function Manifold Components The function manifold is located under the turntable cover at the ground controls side of the machine. Index No. Description Schematic Item Function Torque — Coil nut (items F, H, J, K, N, P and R) ....................................................................................... 4-5 ft-lbs / 7-9 Nm 1 Hand pump ............................................ A ........ Auxiliary down ..................................... 25-27 ft-lbs / 34-36 Nm 2 Relief valve, 600 psi / 41 bar ................. B ........ Turntable rotate circuit ........................ 18-20 ft-lbs / 25-27 Nm 3 Differential sensing valve ..................... C ........ Returns extra hydraulic fluid to tank when operating turntable rotate function ...................................... 25-27 ft-lbs / 34-36 Nm 4 Shuttle valve, 2 position 3 way ............. D ........ Turntable rotate circuit ................................... 4-5 ft-lbs / 6 Nm 5 — Orifice - plug, 0.040 inch / 1 mm ............ E ........ Restricts turntable rotate fluid flow Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 6 Solenoid valve, 2 position 3 way with manual override ............................. F ........ Secondary boom down ....................... 18-20 ft-lbs / 25-27 Nm 7 Diagnostic nipple .................................. G ........ Testing 8 Solenoid valve, 2 position 3 way with manual override ............................ H ........ Primary boom down ............................ 18-20 ft-lbs / 25-27 Nm 9 Relief valve, 1600 psi / 110 bar ............. I ......... Primary boom circuit ........................... 18-20 ft-lbs / 25-27 Nm 10 Solenoid valve, 2 position 3 way with manual override ............................. J ......... Primary boom up ................................. 18-20 ft-lbs / 25-27 Nm 11 Solenoid valve, 3 position 4 way with manual override ............................. K ........ Boom extend/retract ............................ 18-20 ft-lbs / 25-27 Nm 12 Relief valve, 3000 psi / 207 bar ............. L ........ System relief ........................................ 18-20 ft-lbs / 25-27 Nm 13 Counterbalance valve .......................... M ........ Outrigger retract circuit ........................ 30-35 ft-lbs / 41-47 Nm 14 Solenoid valve, 3 position 4 way .......... N ........ Outrigger extend/retract ...................... 18-20 ft-lbs / 25-27 Nm 15 Check valve .......................................... O ........ Outrigger retract circuit ........................ 25-30 ft-lbs / 34-41 Nm 16 Solenoid valve, 2 position 3 way ........... P ........ Secondary boom up ............................ 18-20 ft-lbs / 25-27 Nm 17 — Orifice - plug, 0.080 inch / 2 mm ........... Q ........ Restricts platform down fluid flow Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 18 Solenoid valve, 3 position 4 way with manual override ............................ R ........ Turntable rotate left/right ..................... 18-20 ft-lbs / 25-27 Nm 4 - 30 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures MANIFOLDS A B 1 2 Note: 'alpha-numeric' callouts refer to corresponding notes on the electrical schematic C Note: 'alpha' callouts refer to corresponding notes on the hydraulic schematic Y23 18 D Y22 R E 3 4 5 Y52 F 6 Y53 17 Q G Y21 16 H P I Y22 J 7 8 9 10 Y26 Y25 K 15 Y40 14 11 O L N 12 Y39 M Part No. 84577 Genie TZ-50 13 4 - 31 Section 4 • Repair Procedures September 2014 MANIFOLDS 8-2 Jib Manifold Components The jib manifold is located on the jib boom. Index No. Description Schematic Item Function Torque — Coil nut (items AA, AB, AD and AE) ......................................................................................... 4-5 ft-lbs / 7-9 Nm 1 Solenoid valve, 2 position 3 way ......... AA ....... Jib boom up ......................................... 18-20 ft-lbs / 25-27 Nm 2 Solenoid valve, 2 position 3 way ......... AB ....... Jib boom down .................................... 18-20 ft-lbs / 25-27 Nm 3 Relief valve, 3000 psi / 207 bar ........... AC ....... Platform level circuit ............................ 18-20 ft-lbs / 25-27 Nm 4 Solenoid valve, 3 position 4 way ......... AD ....... Platform rotate left/right ....................... 18-20 ft-lbs / 25-27 Nm 5 Solenoid valve, 3 position 4 way ......... AE ....... Platform up/down ................................ 18-20 ft-lbs / 25-27 Nm 6 Counterbalance valve ......................... AF ....... Platform level circuit ............................ 25-30 ft-lbs / 34-41 Nm 7 Differential sensing valve .................... AG ....... Maintains fluid flow to jib boom, platform level and platform rotate functions ...................... 25-27 ft-lbs / 34-36 Nm 8 — Orifice - plug, 0.055 inch / 1.4 mm ....... AH ....... Platform rotate circuit Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 9 — Orifice - plug, 0.055 inch / 1.4 mm ........ AI ........ Jib boom up circuit Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 10 — Orifice - plug, 0.040 inch / 1 mm ........... AJ ....... Jib boom down circuit Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 11 Shuttle valve, 2 position 3 way ............ AK ....... Platform level circuit ....................................... 4-5 ft-lbs / 6 Nm 4 - 32 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures MANIFOLDS 1 2 3 4 5 AC AD AE AB AA Models with Platform Rotate Y60 Y20 AF Y61 11 10 9 8 6 Y63 AK Y19 AJ Y62 AI Note: 'alpha' callouts refer to corresponding notes on the hydraulic schematic AH Note: 'alpha-numeric' callouts refer to corresponding notes on the electrical schematic AG 7 AC 3 AB 2 AA 1 AE 5 Y60 Y20 Models without Platform Rotate 11 10 9 7 Part No. 84577 AF Y61 6 AK Y19 AJ AI AG Genie TZ-50 4 - 33 Section 4 • Repair Procedures September 2014 MANIFOLDS 8-3 Drive Manifold Components (if equipped) The drive manifold is located next to the function manifold. Index No. Description Schematic Item Function Torque — Coil nut (items BI, BK, BL, BN and BO) .................................................................................... 4-5 ft-lbs / 7-9 Nm 1 Differential sensing valve .................... BA ....... Maintains traction equal to BJ ............. 25-27 ft-lbs / 34-36 Nm 2 Orifice - plug, 0.090 inch / 2.3 mm ....... BB ....... Drive circuit 3 Differential sensing valve .................... BC ....... Maintains torque while driving ............ 25-27 ft-lbs / 34-36 Nm 4 — Orifice - plug, 0.090 inch / 2.3 mm ....... BD ....... Pump 2 circuit Port plug ....................................................................................................................... 97-117 in-lbs / 11-13 Nm 5 Counterbalance valve ......................... BE ....... Drive circuit, left side ........................... 30-35 ft-lbs / 41-47 Nm 6 Differential sensing valve .................... BF ....... Returns pump 2 hydraulic fluid to tank when not driving ...................... 25-27 ft-lbs / 34-36 Nm 7 Counterbalance valve ......................... BG ....... Drive circuit, right side ......................... 25-30 ft-lbs / 34-41 Nm 8 Shuttle valve, 2 position 3 way ............ BH ....... Drive circuit ..................................................... 4-5 ft-lbs / 6 Nm 9 Solenoid valve, 2 position 2 way .......... BI ........ Brake release ...................................... 18-20 ft-lbs / 25-27 Nm 10 Differential sensing valve ..................... BJ ....... Maintains traction equal to BA ............ 25-27 ft-lbs / 34-36 Nm 11 Proportional valve, 2 position 2 way ... BK ....... Drive circuit, right side ......................... 18-20 ft-lbs / 25-27 Nm 12 Solenoid valve, 2 position 4 way ......... BL ....... Drive circuit, right side ......................... 18-20 ft-lbs / 25-27 Nm 13 Check valve, 10 psi / 0.7 bar ............... BM ....... Pump 2 circuit ...................................... 18-20 ft-lbs / 25-27 Nm 14 Solenoid valve, 2 position 4 way ......... BN ....... Drive circuit, left side ........................... 18-20 ft-lbs / 25-27 Nm 15 Proportional valve, 2 position 2 way ... BO ....... Drive circuit, left side ........................... 18-20 ft-lbs / 25-27 Nm 4 - 34 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures MANIFOLDS 1 Note: 'alpha-numeric' callouts refer to corresponding notes on the electrical schematic BA 2 BB 3 BC Note: 'alpha' callouts refer to corresponding notes on the hydraulic schematic BD 4 Y59 15 BO BE 14 Y50 BN BF 13 11 6 BM BG 12 5 Y50A BL BH Y11 BK BI 7 8 9 Y58 10 BJ Y11 9 BI Before Serial Number TZ5004-152 Part No. 84577 Genie TZ-50 After Serial Number TZ5004-151 4 - 35 Section 4 • Repair Procedures September 2014 MANIFOLDS 8-4 Valve Adjustments Function Manifold How to Adjust the Primary Boom Down Relief Valve 1 Connect a 0 to 5000 psi / 0 to 350 bar pressure gauge to the test port (item G) on the function manifold. How to Adjust the System Relief Valve Note: Perform this procedure with the outriggers in the stowed position. 1 Connect a 0 to 5000 psi / 0 to 350 bar pressure gauge to the test port (item G) on the function manifold. 2 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 2 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 3 Push and hold the yellow function enable button. Push and hold the auto level button. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. 3 Push and hold the yellow function enable down button. Observe the pressure reading on the pressure gauge. Refer to Section 2, Specifications. 4 Push and hold the yellow function enable button. Push and hold the primary boom down button. Fully lower the primary boom and continue to hold the buttons while observing the pressure reading on the pressure gauge. Refer to Section 2, Specifications. 4 Release the button. Use a wrench to hold the relief valve and remove the cap (item L). 5 Release the buttons. Use a wrench to hold the relief valve and remove the cap (item I). 5 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Install the relief valve cap. 6 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified. 6 Repeat step 3 to confirm the relief valve pressure. 4 - 36 Tip-over hazard. Do not adjust the relief valve higher than specified. 7 Repeat step 4 to confirm the relief valve pressure. Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures MANIFOLDS How to Adjust the Turntable Rotate Relief Valve 1 Connect a 0 to 5000 psi / 0 to 350 bar pressure gauge to the test port (item G) on the function manifold. 2 Turn the key switch to ground control and pull out the red Emergency Stop button to the on position at both the ground and platform controls. 3 Push and hold the yellow function enable button. Push and hold the auto level button. Result: The outriggers will lower and adjust to level the machine and raise the wheels off the ground. 4 Raise the secondary boom approximately 12 inches / 30 cm. 5 Push and hold the blue function enable button. Push and hold the turntable rotate button. Fully rotate the turntable and continue to hold the buttons while observing the pressure reading on the pressure gauge. Refer to Section 2, Specifications. 6 Release the buttons. Use a wrench to hold the relief valve and remove the cap (item B). 7 Adjust the internal hex socket. Turn it clockwise to increase the pressure or counterclockwise to decrease the pressure. Install the relief valve cap. Tip-over hazard. Do not adjust the relief valve higher than specified. 8 Push and hold the yellow function enable button. Push and hold the turntable rotate button and fully rotate the turntable in the opposite direction. Begin timing when the turntable begins to rotate. 9 Continue rotating the turntable and note the time when the machine stops rotating at 359°. Refer to Section 2, Specifications. Part No. 84577 Genie TZ-50 4 - 37 Section 4 • Repair Procedures September 2014 MANIFOLDS 8-5 Valve Coils Valve Coil Resistance Description How to Test a Coil A properly functioning coil provides an electromotive force which operates the solenoid valve. Critical to normal operation is continuity within the coil that provides this force field. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 1 Tag and disconnect the wire harness from the coil to be tested. Solenoid valve, 2 position 3 way 20V DC with diode (schematic items F, G, I, AA and AB) 25 to 27Ω Solenoid valve, 3 position 4 way 20V DC with diode (schematic items J, M, Q, AD and AE) 25 to 27Ω Solenoid valve, 2 position 4 way 20V DC with diode (schematic item Bl and BN) 25 to 27Ω Solenoid valve, 2 position 2 way N.C. 20V DC with diode (schematic item BI) 25 to 27Ω Proportional valve, 2 position 2 way N.C. 25 to 27Ω 20V DC with diode (schematic item BK and BO) 2 Test the coil resistance. Result: The resistance should be within specification, plus or minus 30%. Result: If the resistance is not within specification, plus or minus 30%, replace the coil. 4 - 38 Specification Solenoid valve, 2 position 2 way N.C.29 to 31W 24V DC with diode (schematic items CA, CB, CC and CD) Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures MANIFOLDS How to Test a Coil Diode 3 Set a multimeter to read DC amperage. Genie incorporates spike-suppressing diodes in all of its coils. Properly functioning coil diodes protect the electrical circuit by suppressing voltage spikes. Voltage spikes naturally occur within a function circuit following the interruption of electrical current to a coil. Faulty diodes can fail to protect the electrical system, resulting in a tripped circuit breaker or component damage. Note: The multimeter, when set to read DC amperage, should be capable of reading up to 800 mA. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. 1 Test the coil for resistance. See 4-3, How to Test a Coil. 2 Connect a 10Ω resistor to the negative terminal of a known good 9V DC battery. Connect the other end of the resistor to a terminal on the coil. Note: The battery should read 9V DC or more when measured across the terminals. Ω Resistor, 10Ω Genie part number 4 Connect the negative lead to the other terminal on the coil. Note: If testing a single-terminal coil, connect the negative lead to the internal metallic ring at either end of the coil. 5 Momentarily connect the positive lead from the multimeter to the positive terminal on the 9V battery. Note and record the current reading. 6 At the battery or coil terminals, reverse the connections. Note and record the current reading. Result: Both current readings are greater than 0 mA and are different by a minimum of 20%. The coil is good. Result: If one or both of the current readings are 0 mA, or if the two current readings do not differ by a minimum of 20%, the coil and/or its internal diode are faulty and the coil should be replaced. 27287 COIL MULTI METER d a + c 10 W RESISTOR b 9V BATTERY + c a b c d b multimeter 9V DC battery 10Ω resistor coil Note: Dotted lines in illustration indicate a reversed connection as specified in step 6 Part No. 84577 Genie TZ-50 4 - 39 Section 4 • Repair Procedures September 2014 Hydraulic Tank 9-1 Hydraulic Tank 3 Tag and disconnect the return hard line from the filter head. Remove the hard line from the machine. Cap the fitting on the filter head. The primary functions of the hydraulic tank are to cool and deaerate the hydraulic fluid during operation. It has an external return line filter. 4 Tag and disconnect the supply hard line from the pump. Cap the fitting on the pump. How to Remove the Hydraulic Tank Component damage hazard. The work area and surfaces where this procedure will be performed must be clean and free of debris that could get into the hydraulic system. Note: When removing a hose assembly or fitting, the O-ring (if equipped) on the fitting and/or the hose end must be replaced. All connections must be torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 5 Remove the hydraulic tank retaining fasteners and remove the hydraulic tank and supply hard line from the machine. a d b c a b c d Note: Perform this procedure with the platform in the stowed position. 1 Disconnect the battery pack from the machine. Electrocution hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. hydraulic filter supply hard line (to pump) hydraulic tank return hard line (from filter) Torque specifications Hydraulic tank retaining fasteners, dry 35 in-lbs 4 Nm Hydraulic tank retaining fasteners, lubricated 26 in-lbs 2.9 Nm 2 Remove the drain plug from the hydraulic tank and allow all of the oil from the tank to drain into a suitable container. Refer to Section 2, Specifications . Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 - 40 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures Axle Components 10-1 Axle CE models: How to Remove the Axle 2 Disconnect the secondary brake cables at the tension equalizer. 1 Lower the outriggers and adjust to level the machine and raise the wheels off the ground. ANSI models: 1 Lower the outriggers and adjust to level the machine and raise the wheels off the ground. 2 Disconnect the secondary brake cables at the tension equalizer. 3 Support and secure the axle assembly to an appropriate lifting device. 4 Remove the axle mounting fasteners and remove the axle from the machine. Crushing hazard. The axle could become unbalanced and fall if not properly supported and secured when removed from the machine. 3 Pull the cables free of the trailer. 4 Tag, disconnect and plug the brake line from the back of the hub. Cap the fitting. a 5 Clean up any brake fluid that may have spilled. b c d 6 Repeat steps 4 through 5 for the other side. 7 Support and secure the axle assembly to an appropriate lifting device. 8 Remove the axle mounting fasteners and remove the axle from the machine. Models with Drive (option) Crushing hazard. The axle could become unbalanced and fall if not properly supported and secured when removed from the machine. a Note: When the axle is installed, the brakes should be bled. Refer to the appropriate brake manufacturer's manual that was shipped with your Genie TZ. Models without Drive c d a b c d Part No. 84577 Genie TZ-50 primary brake cable parking brake cylinder (models with drive option) tension equalizer secondary brake cables 4 - 41 Section 4 • Repair Procedures September 2014 Trailer Components 11-1 Hydraulic and Mechanical Brakes 11-2 Parking Brake How to Adjust the Parking Brake Hydraulic Brake System Hydraulic Axle ANSI models: Repair procedures and additional axle information is available in the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). 1 Adjust the brakes. Refer to the Dexter Axle Operation Maintenance Service Manual (Dexter part number LIT-001-00). Dexter Axle Operation Maintenance Service Manual Genie part number 84376 Dexter Axle Operation Maintenance Service Manual Genie part number 84376 2 Chock the wheels. 3 Release the parking brake. Mechanical Brake System Mechanical Axle 4 Loosen the set screw at the side of the parking brake handle. Repair procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). 5 Adjust the handle just to the point where it is difficult to apply the parking brake, then rotate the top of the parking brake handle counterclockwise one full turn. KNOTT Axle Service Manual Genie part number 6 Tighten the set screw. Do not over tighten. 84443 7 Engage the parking brake. Attempt to move the machine. Result: The parking brake should prevent the machine from moving. If the parking brake does not prevent the machine from moving, repeat this procedure beginning with step 1. CE models: Required maintenance procedures and additional axle information is available in the KNOTT Axle Service Manual (KNOTT part number P005). KNOTT Axle Service Manual Genie part number 4 - 42 Genie TZ-50 84443 Part No. 84577 September 2014 Section 4 • Repair Procedures Outriggers 12-1 Outrigger Components 7 Place a wooden block under the cylinder. How to Remove an Outrigger 9 Using a soft metal drift, remove the outrigger cylinder rod end pivot pin. 8 Lower the outrigger enough to remove the outrigger cylinder rod end pivot pin. Outriggers are essential to safe machine operation and machine stability. Operating a machine with a damaged or improperly operating outrigger will result in death or serious injury. Note: Perform this procedure with the machine disconnected from the tow vehicle and the parking brake applied. Note: Perform this procedure with the outriggers in the stowed position. Crushing hazard. The cylinder could fall if not properly supported when the pivot pin is removed from the machine. 10 Using a soft metal drift, remove the outrigger pivot pin. Remove the outrigger from the machine. 1 Attach a lifting strap of suitable capacity from an overhead crane to the pad end of the outrigger. Do not apply any lifting pressure. Crushing hazard. The outrigger will fall if not properly supported when the pivot pin is removed from the machine. 2 Tag and disconnect the wire harness from the outrigger valve coil. 3 Tag, disconnect and plug the hydraulic hoses at the outrigger cylinder. Cap the fittings. 4 Remove the pin retaining fasteners from the outrigger pivot pin. Do not remove the pin. 5 Remove the pin retaining fasteners from the outrigger cylinder rod end pivot pin. 6 Attach a lifting strap of suitable capacity from an overhead crane to the rod end of the outrigger cylinder. Support the cylinder. Do not apply any lifting pressure. Part No. 84577 Genie TZ-50 4 - 43 Section 4 • Repair Procedures September 2014 OUTRIGGERS 6 Attach a lifting strap from an overhead crane to the lug on the rod end of the cylinder. 12-2 Outrigger Cylinder 7 Remove the pin retaining fasteners from the outrigger cylinder rod-end pivot pin. How to Remove an Outrigger Cylinder 8 Using a soft metal drift, remove the outrigger cylinder rod-end pivot pin. When removing a hose assembly or fitting, the Oring on the fitting and/or hose end must be replaced and then torqued to specification during installation. Refer to Section 2, Hydraulic Hose and Fitting Torque Specifications. 1 Extend the outrigger until the pad just touches the ground. Do not rest the weight of the machine on the outrigger. 9 Raise the cylinder to a vertical position. 10 Remove the pin retaining fasteners from the outrigger cylinder barrel-end pivot pin. 11 Using a soft metal drift, remove the outrigger cylinder barrel-end pivot pin. 2 Remove the hose guard mounting fasteners from the rod end of the outrigger cylinder and remove the hose guard from the machine. 3 Remove the cover above the barrel end of the outrigger cylinder. 4 Tag and disconnect the wire harness from the outrigger cylinder valve coil. Crushing hazard. The outrigger cylinder could fall if not properly supported when the pivot pin is removed from the machine. Component damage hazard. The solenoid valve can be damaged. Use caution when removing the cylinder from the machine. 5 Tag, disconnect and plug the hydraulic hoses from the outrigger cylinder. Cap the fittings on the cylinder. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 - 44 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures Platform Overload Components 13-1 Platform Overload System Determine the limit switch trigger point: Calibrate the Platform Overload System (if equipped) 8 Check the continuity between the black and red wires originating from the limit switch of the platform overload assembly. 7 Gently move the platform up and down by hand, so it bounces 1 to 2 inches / 2.5 to 5 cm. Note: Perform this procedure with the machine on a firm, level surface. 1 At the ground controls, extend the outriggers until the axle is off the ground and the machine is level. 2 Release the boom hold down latch and raise the platform approximately 2 feet / 60 cm. Level the platform. 3 Tag and disconnect the wire harness from the load sense limit switch. Note: The load sense limit switch is located near the platform support. 4 Set a multi-meter to measure continuity. Connect the leads from the multi-meter to the black and red wires disconnected from the limit switch in step 3. 5 Determine the maximum platform capacity. Refer to the machine serial plate. 6 Using a suitable lifting device, place an appropriate test weight equal to that of the maximum platform capacity at the center of the platform floor. Part No. 84577 Result: There is no continuity. Slowly tighten the load spring adjustment nut by turning it clockwise just until the limit switch closes and shows continuity. Result: There is continuity. Slowly loosen the load spring adjustment nut by turning it counterclockwise just until the limit switch opens and shows no continuity. Note: The platform will need to be continuously moved up and down while making adjustments. Fine adjustment of the switch trigger point: 9 Continue moving the platform up and down and adjust the load spring adjustment nut clockwise or counterclockwise just until the limit switch is alternately opening and closing. Note: When the limit switch is adjusted correctly, there will be continuity slightly longer than no continuity. 10 Remove the continuity tester from the limit switch wires. Securely install the wires onto the limit switch. Genie TZ-50 4 - 45 Section 4 • Repair Procedures September 2014 PLATFORM OVERLOAD COMPONENTS Confirm the setting: 11 Turn the key switch to platform control. 12 Lift the test weight off the platform floor using a suitable lifting device. 13 Place the test weight back onto the platform floor using a suitable lifting device. Result: The platform overload indicator light should be off at both the ground and platform controls. 14 Add an additional 44 lbs / 20 kg of weight to overload the platform. Result: The platform overload indicator light should be flashing at both the ground and platform controls. 15 Test all machine functions from the platform controls. Result: All platform control functions should not operate. 16 Turn the key switch to ground control. 17 Test all machine functions from the ground controls. Result: All ground control functions should not operate. 4 - 46 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures Drive Components The TZ-50 drive option allows the operator to move the machine into another position without having to use a tow vehicle to do so. This option package includes drive controls, a brake cylinder, and a drive motor for each axle wheel. When a drive function is activated at the drive control box, a signal is sent to one or more of the drive manifold valve coils, enabling the machine to move. The drive controls will function only when the machine is in the stowed position, the parking brake is set, and both wheel motors are in place against the axle tires. To begin, manually move and lock the drive wheels in place against the axles tires. Then, by squeezing the joystick, to activate the drive function enable button, and moving the joystick in the desired direction, the parking brake will release via the parking brake cylinder located under the chassis, and both drive motors will activate which will in turn move the machine. Returning the joystick to the neutral position will disable the drive and steer function, and set the parking brake. Part No. 84577 14-1 Drive Motor How to Remove a Drive Motor When removing a hose assembly or fitting, the Oring on the fitting and/or hose end must be replaced and then torqued to specification during installation. Refer to Section Two, Hydraulic Hose and Fitting Torque Specifications. 1 Remove the drive wheel retaining fasteners. 2 Remove the drive wheel. 3 Tag, disconnect and plug the hydraulic hoses from the drive motor. Cap the fittings. Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. 4 Remove the drive motor mounting fasteners and remove the drive motor from the machine. Genie TZ-50 4 - 47 Section 4 • Repair Procedures September 2014 DRIVE COMPONENTS 14-2 Drive Control Box How to Remove the Drive Circuit Board Drive Control Box Circuit Board Activating the joystick or a button on the box first sends a signal to the drive controls circuit board, then to the ground controls and finally the drive manifold valve coils which ultimately activates the drive function. The drive/steer functions can only be operated when the machine is in the stowed position and the parking brake set. Over time, it may be necessary to recalibrate the drive controls. The drive controls printed circuit board can be adjusted for three different functions: steer left, steer right, and forward/reverse. For each function to operate correctly, two side-by-side potentiometers, Threshold and Hi-range, must be carefully adjusted. When accurately calibrated, the machine should steer and drive smoothly. 1 Tag and disconnect the drive control wire harness from the ground controls. 2 Remove the drive control box from the control box mount. Turn the box over and remove the fasteners securing the bottom cover to the box. Remove the cover. 3 Locate the 6-pin Deutsch connector between the circuit board and the 14-wire main cable. Note: The 6-pin connector and wiring originates from the circuit board nearest the B SIDE potentiometer. Note: On the circuit board side, seven wires are installed into the 6-pin connector with two red wires installed into terminal 1. The drive control box consists of a printed circuit board, Emergency Stop button, joystick and, for ANSI models, buttons to operate the outriggers. All of the components are replaceable. Keeping the drive controls clean and defect free is essential to safe machine operation. For further information or assistance, consult the Genie Industries Service Department. a b drive controls circuit board 14-wire main cable 4 Tag and disconnect the circuit board from the 14-wire main cable. Component damage hazard. Electrostatic discharge (ESD) can damage printed circuit board components. Use a grounded wrist strap at all times when handling printed circuit boards. 5 Tag and disconnect the joystick from the circuit board. 6 Remove the circuit board mounting fasteners and remove the circuit board from the box. 4 - 48 Genie TZ-50 Part No. 84577 September 2014 Section 4 • Repair Procedures DRIVE COMPONENTS How to Calibrate the Drive Circuit Board - to SN TZ5008-532 1 Remove the blue wire from terminal 1 of the motor controller U6. 2 Remove the drive control box from the control box mount. Turn the box over and remove the fasteners securing the bottom cover to the box. Remove the cover. 3 Turn the key switch to platform controls and pull out the Emergency Stop button to the on position at the ground, platform and drive controls. Adjust both B SIDE potentiometers: 4 Without disconnecting the wire harness, connect the negative lead of the multimeter to the black wire of the 14-wire main cable. 5 Without disconnecting the wire harness, connect the positive lead of the multimeter to the orange wire of the 14-wire main cable. 6 Squeeze the joystick to activate the function enable switch SW5. The voltage is 21.9 to 22.1V DC. Proceed to step 9. a b c A side potentiometers SW DC potentiometers B side potentiometers 10 While activating the function enable switch and holding the joystick fully in the right direction, adjust the B SIDE THRESHOLD potentiometer until the voltage is 3V DC. Release the joystick. 11 Repeat this procedure beginning with step 9. 12 Disconnect the positive lead. Adjust both A SIDE potentiometers: 13 Without disconnecting the wire harness, connect the positive lead of the multimeter to the orange/black wire of the 14-wire main cable. 14 Squeeze the joystick to activate the function enable switch SW5. The voltage is less than 21.9 or greater than 22.1V DC. Proceed to step 7. The voltage is 21.9 to 22.1V DC. Proceed to step 17. 7 While activating the function enable switch, adjust the B SIDE HI RANGE potentiometer until the voltage is 22V DC. Release the joystick. The voltage is less than 21.9 or greater than 22.1V DC. Proceed to step 15. 8 Repeat this procedure beginning with step 6. 9 Activate the function enable switch and move the joystick fully in the right direction. 15 While activating the function enable switch, adjust the A SIDE HI RANGE potentiometer until the voltage is 22V DC. Release the joystick. The voltage is 3V DC. Proceed to step 12. The voltage is less than or greater than 3V DC. Proceed to step 10. Part No. 84577 Genie TZ-50 4 - 49 Section 4 • Repair Procedures September 2014 DRIVE COMPONENTS 16 Repeat this procedure beginning with step 14. 17 Activate the function enable switch and move the joystick fully in the left direction. The voltage is 3V DC. Proceed to step 20. The voltage is less than or greater than 3V DC. Proceed to step 18. 18 While activating the function enable switch and holding the joystick fully in the left direction, adjust the A SIDE THRESHOLD potentiometer until the voltage is 3V DC. Release the joystick. 19 Repeat this procedure beginning with step 17. 26 While activating the function enable switch and holding the joystick fully in the reverse direction, adjust the SW DC HI RANGE potentiometer until the voltage is 4.9V DC. Release the joystick. 27 Repeat this procedure beginning with step 25. 28 Confirm the forward and reverse settings. Repeat this procedure beginning with step 22. Adjusting the SW DC THRESHOLD potentiometer will determine where the voltage begins as you move the joystick in either forward or reverse. 29 Disconnect the positive and negative leads. 20 Disconnect the positive lead. Adjust both SW DC potentiometers: 21 Without disconnecting the wire harness, connect the positive lead of the multimeter to the blue/ black wire of the 14-wire main cable. 22 Activate the function enable switch and move the joystick fully in the forward direction. The voltage is 4.9V DC. Proceed to step 25. The voltage is less than or greater than 4.9V DC. Proceed to step 23. 23 While activating the function enable switch and holding the joystick fully in the forward direction, adjust the SW DC HI RANGE potentiometer until the voltage is 4.9V DC. Release the joystick. 30 Push in the red Emergency Stop button to the off position at the ground, platform and drive controls. 31 Apply SentrySeal to the screws of the potentiometers which were adjusted. 32 Install the cover onto the box. Install and securely tighten the fasteners. 33 Install the drive control box onto the machine. Secure with the control box latch. 34 Securely connect the blue wire to terminal 1 of the motor controller. 35 Perform the function tests. Refer to the Operator’s Manual on your machine. 24 Repeat this procedure beginning with step 22. 25 Activate the function enable switch and move the joystick fully in the reverse direction. The voltage is 4.9V DC. Proceed to step 28. The voltage is less than or greater than 4.9V DC. Proceed to step 26. 4 - 50 Genie TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Schematics About This Section There are two groups of schematics in this section. Electrical Schematics Electrocution/burn hazard. Contact with electrically charged circuits could result in death or serious injury. Remove all rings, watches and other jewelry. Observe and Obey: Troubleshooting and repair procedures shall be completed by a person trained and qualified on the repair of this machine. Hydraulic Schematics Bodily injury hazard. Spraying hydraulic oil can penetrate and burn skin. Loosen hydraulic connections very slowly to allow the oil pressure to dissipate gradually. Do not allow oil to squirt or spray. Immediately tag and remove from service a damaged or malfunctioning machine. Repair any machine damage or malfunction before operating the machine. Before Troubleshooting: Read, understand and obey the safety rules and operating instructions in the appropriate Operator's Manual on your machine before attempting any maintenance or repair procedure. Be sure that all necessary tools and test equipment are available and ready for use. General Repair Process Identify symptoms Malfunction discovered Troubleshoot problem still exists Return to service Part No. 84577 TZ-50 problem solved Inspect and test Perform repair 5-1 Section 5 • Schematics September 2014 Electrical Abbreviations Legend Item B Description Battery Item BN Description Button B5 Battery BN94 BN Button BN2 BN3 BN36 BN49 BN50 BN51 BN52 BN53 BN54 BN55 BN56 BN57 BN58 BN59 Engine start Choke Jib boom up/down Outrigger auto level Left rear outrigger Right rear outrigger Left front outrigger Right front outrigger Primary boom up/down Secondary boom up/down Boom extend/retract Turntable rotate Platform level up/down Function enable (boom down, boom retract, rotate left, outrigger extend) Function enable (boom up, boom extend, rotate right, outrigger retract) Function enable (boom down, boom retract, turntable/platform rotate left) Function enable (boom up, boom extend, turntable/platform rotate right) Primary boom up/down Secondary boom up/down Boom extend/retract Turntable rotate Platform level up/down Engine start Choke Platform rotate BN96 BN97 BN98 Function enable (boom down, boom retract, rotate left, outrigger extend) Function enable (boom up, boom extend, rotate right, outrigger retract) Autolevel Jib boom up/down Platform rotate C Capacitor C4 C4A C4B C5 Zener diode, 5.1V DC Zener diode, 3.3V DC Zener diode, 5.1V DC 4700uF BN60 BN61 BN62 BN63 BN64 BN65 BN66 BN67 BN68 BN90 BN93 5-2 BN95 CB Circuit Breaker CB1 CB2 Engine, 15A Controls, 15A CR Control Relay CR1 CR8 CR9 CR15 CR28 CR61 CR64 CR65 CR66 CR67 CR68 CR69 CR70 Engine start Ignition Jib boom up/down Choke Power supply Auto level system Fault ground Motor controller cutout Level sensor (auto level) Primary boom Secondary boom Boom extend/retract Turntable rotate TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Electrical Abbreviations Legend Item CR Description Control Relay Item L Description Light or LED CR71 CR72 CR73 CR74 CR75 CR76 CR77 CR78 CR86 CR87 Platform level Outrigger Function enable (ground controls) Function enable (platform controls) Level sensor Limit switch fault Down enable Lift cut-out Sequencing Platform rotate D1 Alternator L4 L4A L12 L13 L14 L15 L33 L34 L35 L36 L58 Load sense at ground (load sense option) Load sense at platform (load sense option) Left front outrigger Right front outrigger Left rear outrigger Right rear outrigger Right rear tail light Left rear tail light Right side marker Left side marker License plate light F Fuse LS Limit Switch F6 F9 F9A Function, 275A Alternator, 50A Engine starter, 50A FB1 Flashing Beacons (option) GND Ground G Gauge LS12 LS13 LS14 LS15 LS18 LS18A LS19 Left front outrigger Right front outrigger Left rear outrigger Right rear outrigger Boom down Boom down Load sense G6 G7 Hour meter Battery charge indicator (option) M Motor M3 M5 Engine starter Hydraulic power unit Normally closed H Horn or Alarm H1 H5 Horn Multifunction alarm N.C. JC5 Joystick N.O. KS1 Keyswitch NOHC Normally open, held closed Part No. 84577 NCHO Normally closed, held open Normally Open P Power switch P1 P2 P3 Emergency Stop button at ground controls Emergency Stop button at plat. controls Emergency Stop button at drive controls Q7 Choke Solenoid TZ-50 5-3 Section 5 • Schematics September 2014 Electrical Abbreviations Legend Item R Description Resistor Wire Color Legend Item ...................................... Description R14 R22 R22B Function speed, 0-10K ohms 1000 ohm 5600 ohm S Sensor S7 S9 S10 Level sensor Level sensor, front/rear axis (auto level) Level sensor, left/right axis (auto level) BL .................................................. BK ................................................. GN ................................................. OR ................................................. RD ................................................. WH ................................................. BL/BK ............................................ BL/WH ........................................... BK/RD ........................................... BK/WH ........................................... GN/BK ........................................... GN/WH .......................................... OR/BK ........................................... OR/RD ........................................... OR/WH .......................................... RD/BK ........................................... RD/WH ........................................... WH/BK ........................................... WH/RD ........................................... U Electronic Component U6 U9 U16 U24 U26 Motor controller Battery charger Time delay Drive controls printed circuit board Ignition module Y Valve Coil Y11 Y19 Y20 Y21 Y22 Y23 Y24 Y25 Y26 Y33 Y34 Y35 Y36 Y39 Y40 Y50 Y50A Y52 Y53 Y58 Y59 Y60 Y61 Y62 Y63 Brake release Platform down Platform up Primary down Primary up Turntable rotate left Turntable rotate right Boom retract Boom extend Left rear outrigger Right rear outrigger Left front outrigger Right front outrigger Outrigger retract Outrigger extend Drive forward/reverse left Drive forward/reverse right Secondary down Secondary up Proportional drive right Proportional drive left Jib boom retract Jib boom extend Platform rotate left Platform rotate right 5-4 TZ-50 Blue Black Green Orange Red White Blue / Black Blue / White Black / Red Black / White Green / Black Green / White Orange / Black Orange / Red Orange / White Red / Black Red / White White / Black White / Red Part No. 84577 September 2014 Section 5 • Schematics Limit Switch Legend a b c d Item a b c d Description Boom limit switches Outrigger limit switch Boom limit switch Outrigger limit switch Part No. 84577 Schematic LS18 / LS18A LS12/LS13/LS14/LS15 LS18 LS12/LS13/LS14/LS15 TZ-50 to TZ5006-159 to TZ5006-159 from TZ5006-160 5-5 Section 5 • Schematics September 2014 Electrical Symbols Legend 86 30 + TB1 87A Terminal 87 85 6V Battery Control relay Diode Resistor Fuse A1 GROUND PLATFORM M5 LED KS1 S2 Power unit or motor KEY SWITCH + Key switch G6 T2 Hour meter P1 1 B- EMERGENCY STOP Emergency stop button, normally closed B+ 3 Motor controller Alarm CB2 15A Circuit breaker N.C.H.O. N.C. N.O.H.C. Solenoid valve with diode Battery charger Limit switch Quick disconnect Level sensor Toggle switch 5-6 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Abbreviation Legend Hydraulic Schematics Item Description Item Description A B C D E F G H I J K L M N O P Auxiliary pump Relief valve - turntable rotate Pilot operated relief valve Shuttle valve - turntable rotate Orifice - turntable speed Secondary boom down (with override) Primary boom down (with override) Relief valve - primary boom Primary boom up (with override) Boom extend/retract (with override) System relief Outrigger counterbalance Outrigger extend/retract Check valve - outrigger circuit Secondary boom up Orifice - primary/secondary boom down speed Turntable rotate left/right (with override) Jib boom extend Jib boom retract Relief valve - platform level circuit Platform rotate left/right (option) Platform level up/down Platform level counterbalance Pilot operated relief valve Orifice - platform rotate speed Orifice - jib boom up speed Orifice - jib boom down and platform level speed Shuttle valve - platform level circuit BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO CA CB CC CD CE Pilot operated directional valve - left Orifice - drive speed Pilot operated pressure compensator Orifice - drive speed Counterbalance valve Pilot operated pressure compensator Counterbalance valve Shuttle valve Brake Dump Pilot operated directional valve - right Proportional valve - right Drive forward/reverse - right Check valve - drive circuit Drive forward/reverse - left Proportional valve - left Outrigger - left rear Outrigger - right rear Outrigger - left front Outrigger - right front Parking brake release (drive option) Q AA AB AC AD AE AF AG AH AI AJ AK Part No. 84577 TZ-50 5-7 Section 5 • Schematics September 2014 Hydraulic Symbols Legend 0.090 inch 2.3 mm Filter Check valve Shuttle valve Orifice with size M Motor Fixed displacement pump Variable speed motor Fixed displacement hand pump Brake Pilot operated 2 position 2 way directional valve normally open Check valve, pilot to open Brake release Y26 Pilot operated 2 position 2 way pressure compensator normally closed Solenoid operated 2 position 3 way directional valve with manual override Adjustable relief valve Y40 Double acting cylinder 5-8 Solenoid operated 2 position 4 way directional valve Solenoid operated 2 position 3 way directional valve Y39 Counterbalance valve Y53 Solenoid operated 3 position 4 way directional valve Solenoid operated 2 position 2 way directional valve normally closed Solenoid operated 2 position 2 way proportional valve normally closed Y52 Solenoid operated 3 position 4 way directional valve with manual override TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Honda GX160 Engine Wiring Diagram BATTERY (+) STARTER SOLENOID BK/WH WH CONTROL BOX 5A FUSE WH ENGINE KEY SWITCH BK/RD YL OIL LEVEL SWITCH BK TRANSISTORIZED IGNITION UNIT SPARK PLUG Part No. 84577 TZ-50 WH CIRCUIT BREAKER RECTIFIER GN WH CHARGING COIL 5-9 Section 5 • Schematics September 2014 Trailer Lighting Wiring Diagram - ANSI / CSA L35 WH RIGHT SIDE MARKER QD12 GN RD BN BN TRAILER PLUG 1 GN BN/YL 2 L33 BN RIGHT REAR TAIL LIGHT YL 3 BN BK WH 4 1 GN YL RD BK BN 2 YL 3 BN/YL 3 BN WH L36 LEFT SIDE MARKER 5 - 10 L34 LEFT REAR TAIL LIGHT 4 WH TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Trailer Lighting Wiring Diagram - Mechanical Axle, CE (to SN TZ5012-215) Trailer Chassis Wiring Harness L35 RIGHT SIDE MARKER RD BL BL BK BK YL YL WH 6 RD 1 2 3 4 5 6 7 2 L36 YL BL WH GN BN RD BK LEFT SIDE MARKER 3 5 BK 7 WH WH RD WH 6 4 GN 5 BN BR WH BK 3 WH GR BR 1 2 BL BK 1 YL WH BK GR Boom Harness 4 7 BK L35 RIGHT SIDE MARKER BK GN WH Platform Wiring Harness RIGHT REAR GN BN WH RD GY BN GREEN PLUG WH GN - TURN RD - BRAKE BN - RUN GY - FOG WH - GROUND RD BL BK YL BK WH GN BL RD BN YELLOW PLUG WH RD BL BK YL YL WH BK 1 2 3 4 5 6 7 LEFT REAR L36 LEFT SIDE MARKER LEFT REAR TAIL LIGHT 1 4 Part No. 84577 BL - FOG BK - RUN WH - GROUND RD - BRAKE YL - TURN 3 2 RIGHT REAR TAIL LIGHT 1 2 3 4 TURN SIGNAL FOG LIGHT REFLECTOR BRAKE / RUNNING LIGHT TZ-50 2 1 3 4 5 - 11 Section 5 • Schematics September 2014 Trailer Lighting Wiring Diagram - Mechanical Axle, CE (from SN TZ5012-216) L35 RIGHT SIDE MARKER Trailer Chassis Wiring Harness WH WH RD RD BL BL BK BK RD/BK RD/BK WH/BK WH/BK 1 2 3 4 5 6 7 8 WH 9 BK 8 7 1 10 6 2 9-13 Not Used BK OR WH WH RD/BK BL WH GN OR RD BK WH/BK GR OR BK 1 2 3 4 5 6 7 8 WH BK GR 11 L36 4 LEFT SIDE MARKER 5 3 Boom Harness 13 12 RD/BK BL WH GN OR RD BK WH/BK L33 RIGHT REAR TAIL LIGHT GY BACKUP L35 RIGHT SIDE MARKER WH BK GR Platform Wiring Harness GR BR WH RD BL GY OR WH BN RUN GN TURN WH GND RD RD STOP BL BL BK WH RD BL BK YL GY RD/BK RD/BK BL WH GN OR RD BK WH/BK WH/BK WH BK 1 2 3 4 5 6 7 8 FOG BL FOG RD STOP WH L36 YL LEFT SIDE MARKER BK RIGHT REAR TAIL LIGHT LEFT REAR TAIL LIGHT 1 GY GND TURN RUN BACKUP L34 LEFT REAR TAIL LIGHT 2 3 4 5 6 5 - 12 1 2 3 4 5 6 SIDE MARKER TURN SIGNAL FOG LIGHT RED REFLECTOR REVERSE LIGHT BRAKE LIGHT TZ-50 5 6 4 2 1 3 Part No. 84577 September 2014 Section 5 • Schematics Trailer Lighting Wiring Diagram - Electric Axle, AUS (to SN TZ5012-252) - + BATTERY Trailer Chassis Wiring Harness BREAK AWAY ELECTRIC BRAKE + - BATTERY + CHARGER - BK L35 L35 WH RIGHT SIDE MARKER BK WH RD BK ELECTRIC BREAK AWAY KIT BK WH WH BK BK WH YL RD 1 6 5 3 2 7 4 BL WH BK BR 1 2 3 4 5 6 7 GR BK WH WH BK BK WH 7 PIN PLUG INSTALLED BY CUSTOMER 1 YL LEFT TURN SIGNAL 2 BK REVERSE LIGHT 2 BK BREAK AWAY BATTERY CHARGER 3 WH GROUND 4 GN RIGHT TURN SIGNAL 5 BL ELECTRIC BRAKE 6 RD BRAKE LIGHTS 7 BN SIDE MARKERS / FOG LIGHTS / RUN L36 YL BK WH GN BL RD BN L36 LEFT SIDE MARKER Boom Harness ELECTRIC BRAKE L35 RIGHT SIDE MARKER Platform Wiring Harness BK WH GN RIGHT REAR GN RD BN GY WH BN GREEN PLUG WH WH RD BN YL BL BK WH RD YL YELLOW PLUG LEFT REAR BL - FOG BK - RUN WH - GROUND RD - BRAKE YL - TURN BK YL BK WH GN BL RD BN WH BL BK WH 1 2 3 4 5 6 7 GN - TURN RD - BRAKE BN - RUN GY - FOG WH - GROUND L36 LEFT SIDE MARKER LEFT REAR TAIL LIGHT 1 4 Part No. 84577 3 2 TZ-50 RIGHT REAR TAIL LIGHT 1 2 3 4 TURN SIGNAL FOG LIGHT REFLECTOR BRAKE / RUNNING LIGHT 2 1 3 4 5 - 13 Section 5 • Schematics September 2014 Trailer Lighting Wiring Diagram - Electric Axle, AUS (from SN TZ5012-253) - + BATTERY Trailer Chassis Wiring Harness BREAK AWAY ELECTRIC BRAKE + - BATTERY + CHARGER - BK L35 WH L35 RIGHT SIDE MARKER BK WH RD BK ELECTRIC BREAK AWAY KIT BK WH WH BK BK WH YL RD 1 6 5 3 2 7 4 BL WH BK BR 1 2 3 4 5 6 7 GR BK L36 WH WH BK BK WH 7 PIN PLUG INSTALLED BY CUSTOMER 1 YL LEFT TURN SIGNAL 2 BK REVERSE LIGHT 2 BK BREAK AWAY BATTERY CHARGER 3 WH GROUND 4 GN RIGHT TURN SIGNAL 5 BL ELECTRIC BRAKE 6 RD BRAKE LIGHTS 7 BN SIDE MARKERS / FOG LIGHTS / RUN L36 Boom Harness LEFT SIDE MARKER ELECTRIC BRAKE L33 RIGHT REAR TAIL LIGHT GY BACKUP L35 BN RIGHT SIDE MARKER GN BK WH Platform Wiring Harness TURN WH WH GND RD GY WH RD GY STOP BL FOG WH BL BK YL BK WH GN BL RD BN RUN GN GN RD BN BL WH BN BN YL BL BK WH RD YL BL FOG RD STOP WH YL BK WH 1 2 3 4 5 6 7 YL BK WH GN BL RD BN L36 LEFT SIDE MARKER RIGHT REAR TAIL LIGHT LEFT REAR TAIL LIGHT BK GY GND TURN RUN BACKUP L34 1 2 3 4 5 6 5 - 14 1 2 3 4 5 6 SIDE MARKER TURN SIGNAL FOG LIGHT RED REFLECTOR REVERSE LIGHT BRAKE LIGHT LEFT REAR TAIL LIGHT 5 6 4 2 1 3 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Trailer Lighting Wiring Diagram - Hydraulic Axle, AUS (from SN TZ5012-216) L35 RIGHT SIDE MARKER Trailer Chassis Wiring Harness WH WH RD RD BL BL BK BK RD/BK RD/BK WH/BK WH/BK 1 2 3 4 5 6 7 8 WH 9 BK 8 7 1 10 6 2 9-13 Not Used BK OR WH WH RD/BK BL WH GN OR RD BK WH/BK GR OR BK 1 2 3 4 5 6 7 8 WH BK GR 11 L36 4 LEFT SIDE MARKER 5 3 Boom Harness 13 12 RD/BK BL WH GN OR RD BK WH/BK L33 RIGHT REAR TAIL LIGHT GY BACKUP L35 RIGHT SIDE MARKER WH BK GR Platform Wiring Harness GR BR WH RD BL GY OR WH BN RUN GN TURN WH GND RD RD STOP BL BL BK WH RD BL BK YL GY RD/BK RD/BK BL WH GN OR RD BK WH/BK WH/BK WH BK 1 2 3 4 5 6 7 8 FOG BL FOG RD STOP WH L36 YL LEFT SIDE MARKER BK RIGHT REAR TAIL LIGHT LEFT REAR TAIL LIGHT 1 GY GND TURN RUN BACKUP L34 LEFT REAR TAIL LIGHT 2 3 4 5 6 Part No. 84577 1 2 3 4 5 6 SIDE MARKER TURN SIGNAL FOG LIGHT RED REFLECTOR REVERSE LIGHT BRAKE LIGHT TZ-50 5 6 4 2 1 3 5 - 15 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-181) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD KS1 P1 EMERGENCY STOP KEY SWITCH RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB3 CR1 TERMINAL 86 POWER CABLE PIN 1 TURNTABLE HARNESS PIN E CR8 TERMINAL 87 CR1 TERMINAL 30 CR15 TERMINAL 30 TB3 TB10 TB7 RD BN59 BN90 (CE MODELS) CB1 CB2 15 AMP 15 AMP CHOKE L4 WH LED RD WH BN58 BN56 BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER PRIMARY BOOM UP/DOWN TB17 TB18 AUTO LEVEL BK BN54 TB9 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TURNTABLE HARNESS PIN B FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) BN93 L12 BN50 LF LED LEFT REAR OUTRIGGER PLATFORM ROTATE TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH CR73 TERMINAL 87 CR78A TERMINAL 30 WH/BK TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87 BK/WH TB27 RD WH + + H5 ALARM RD G6 HOUR METER -- TB21 CC5 RD BK TB3 PA3 TB32 TB35 ES-TZ50A 5 - 16 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-181) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A 85 13 86 87 87A MANIFOLD HARNESS BK PIN W 14 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 PD10 86 87 87A 4700uF BK/RD RD 85 TURNTABLE HARNESS WH/BK PIN J 86 87 87A CR15 PA2 BN90 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 STARTING AID BL WH/BK 30 85 BN68 ENGINE START 30 18 PA1 CR1 BK/RD 17 PB8 C5 85 BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK 85 86 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T CR70 BL/BK CR86 SEQUENCING BK TB15 TB16 TB35 R22 1000 OHM Part No. 84577 9 86 WH 87 87A RD RD 30 85 8 86 87 87A TB31 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R MANIFOLD HARNESS RD PIN U WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK TZ-50 CR78A BK LIFT CUT-OUT WH WH 30 85 ZENER 5.1V DC 7 86 87 87A WH WH 85 6 86 87A 30 5 87 87A 86 87A 86 87A 86 87A 86 87A RD CD10 CR64 TB2 TB3 FAULT GROUND WH WH 30 85 TB7 CR76 WH 85 1 TB6 LIMIT SWITCH FAULT 30 87 WH WH/BK 30 2 TB12 TB32 TB8 TURNTABLE HARNESS PIN H CR65A U6 CUT-OUT 85 87 CR65B WH 30 3 TB16 U6 CUT-OUT 85 87 CR77 BL 30 4 TB22 DOWN ENABLE 85 87 TB35 CR28 WH WH WH 85 86 TB3 POWER SUPPLY C4A 87 TB11 FUNCTION ENABLE 30 ZENER DIODE 3.3V DC TB35 CR73 WH C4 TB34A BN55 BN58 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR ES-TZ50A 5 - 17 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-182 to TZ5004-324) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD KS1 KEY SWITCH POWER CABLE PIN 1 TURNTABLE HARNESS PIN E TURNTABLE HARNESS PIN B CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) RD BN90 CR1 TERMINAL 86 CB1 CB2 15 AMP 15 AMP FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) WH RD WH BN58 BN56 BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB17 TB18 AUTO LEVEL BK BN93 TB9 BN49 PLATFORM LEVEL UP/DOWN BN54 TB3 BN59 CHOKE BOOM EXTEND/RETRACT TB10 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES-TZ50C 5 - 18 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-182 to TZ5004-324) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS BL/BK PIN R MANIFOLD HARNESS RD PIN U 13 86 87 87A MANIFOLD HARNESS BK PIN W 14 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 85 PB10 17 86 87 87A 86 87 87A RD C5 CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 BN68 CR1 BK/RD 30 18 PA1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J PB8 4700uF BK/RD BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK 85 86 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T TB31 CR70 BL/BK 85 CR86 SEQUENCING 86 WH 87A RD RD DRIVE MANIFOLD HARNESS PIN 8 PLATFORM ROTATE 30 9 87 30 85 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK BK TB15 6A TB16 TB35 R22 1000 OHM PA5 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 C4 ZENER 5.1V DC 7 86 87 87A WH WH 85 6 86 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A RD CD10 CR64 TB2 PA3 FAULT GROUND WH WH 30 85 TB7 CR76 WH 85 DC TB6 LIMIT SWITCH FAULT 30 6A WH WH/BK 30 2 CR65A U6 CUT-OUT 85 87 CR65B TB15 TURNTABLE HARNESS PIN H WH 30 3 TB12 TB32 TB8 U6 CUT-OUT 85 87 CR77 BL 85 4 TB14 DOWN ENABLE 30 87 TB22 CR28 WH WH WH 85 86 TB35 POWER SUPPLY C4A 87 BK LIFT CUT-OUT 30 ZENER DIODE 3.3V DC CR78A TB34A BN55 TB11 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES-TZ50C Part No. 84577 TZ-50 5 - 19 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-325 to TZ5005-284) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 CB1 CB2 15 AMP 15 AMP BN59 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE WH RD WH BN58 BN56 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB18 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TB9 TB17 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES-TZ50F 5 - 20 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-325 to TZ5005-284) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN U 85 13 86 87 87A MANIFOLD HARNESS BK PIN W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T 85 14 86 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 85 PB10 17 86 87 87A 86 87 87A RD C5 CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 BN68 CR1 BK/RD 30 18 PA1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J PB8 4700uF BK/RD BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK 1 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 ZENER DIODE 3.3V DC 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87A WH TB6 TB7 CD10 CR76 WH RD 30 87 CR65A LIMIT SWITCH FAULT 85 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A DC WH 85 TB34A BN55 TB11 CR64 TB2 PA3 FAULT GROUND WH WH 30 85 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES-TZ50F 1 Part No. 84577 TZ-50 FROM TZ5005-211 5 - 21 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 CB1 CB2 15 AMP 15 AMP BN59 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE WH RD WH BN58 BN56 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB18 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TB9 TB17 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH BN51 CC9 1 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM 1 RD G6 HOUR METER -- Contactor was moved to top position. FROM TZ5005-343 TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES0440C 5 - 22 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN U 85 13 86 87 87A MANIFOLD HARNESS BK PIN W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T 85 14 86 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 85 PB10 17 86 87 87A 86 87 87A RD C5 CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 BN68 CR1 BK/RD 30 18 PA1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J PB8 4700uF BK/RD BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A TB6 TB7 CD10 CR76 RD CR64 TB2 PA3 FAULT GROUND WH WH 30 85 WH WH 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES0440C Part No. 84577 TZ-50 5 - 23 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 CB1 CB2 15 AMP 15 AMP BN59 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE WH RD WH BN58 BN56 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB18 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TB9 TB17 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 PB5-7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH PB5-9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 P5-3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 P5-5 BK TB3 PA3 TB32 TB35 ES0440D 5 - 24 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) MANIFOLD HARNESS GN/BK PIN P3-L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN P3-K MANIFOLD HARNESS WH PIN P3-P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN P3-U 85 13 86 87 87A MANIFOLD HARNESS BK PIN P3-W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN P3-T 85 14 86 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 85 P2-10 17 86 87 87A 86 87 87A RD C5 CR15 P1-2 BN90 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 STARTING AID BL WH/BK 30 85 BN68 CR1 BK/RD 30 18 P1-1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN P3-J P2-8 4700uF BK/RD BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS P2-9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN P3-V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN P3-R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN P3-N MANIFOLD HARNESS BL PIN P3-S GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A TB6 TB7 P4-10 CR76 RD CR64 TB2 PA3 FAULT GROUND WH WH 30 85 WH WH 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES0440D Part No. 84577 TZ-50 5 - 25 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5011-132) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 RD CR15 TERMINAL 30 BCI + P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 CB1 CB2 15 AMP 15 AMP BN59 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE WH RD WH BN58 BN56 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB18 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TB9 TB17 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 PB-7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH PB5-9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 P5-3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 P5-5 BK TB3 PA3 TB32 TB35 ES0440G 5 - 26 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5011-132) MANIFOLD HARNESS GN/BK PIN P3-L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN P3-K 85 MANIFOLD HARNESS WH PIN P3-P 11 86 87 87A MANIFOLD HARNESS BL PIN P3-S 86 87 87A 85 MANIFOLD HARNESS RD PIN P3-U 13 86 87 87A 85 MANIFOLD HARNESS BK PIN P3-W 14 86 87 87A 86 87 87A CR68 TB26 CR67 TB12 BK/WH 85 15 TB25 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN P3-V CR70 RD TB27 CR69 BOOM EXTEND RD TB2 BK/WH 30 85 P2-8 CR8 IGNITION BK MODELS P2-9 WITH ENGINE (OPTION) BK 16 86 87 87A P1-1 BK 30 85 BN68 ENGINE START BK/RD P2-10 BK/RD 17 86 87 87A 86 87 87A BN90 RD 85 18 P1-2 BK/RD 30 TURNTABLE HARNESS WH/BK PIN P3-J C5 4700uF CR1 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 CR15 STARTING AID BL TB15 6A WH/BK 30 85 TB16 CR86 SEQUENCING BK WH RD RD 30 TB35 R22 1000 OHM PA5 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN P3-T TB31 RD/BK 86 87A 85 PLATFORM HARNESS TERMINAL PA BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN P3-R CR72 WH/BK 85 12 TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN P3-N TERMINAL BASE GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A WH TB6 TB7 P4-10 CR76 WH RD 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR64 TB2 PA3 FAULT GROUND WH WH 30 85 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A P3-X 1 200 OHM 6A BATTERY CHARGE INDICATOR - G7 + Part No. 84577 DE ES0440G 1 BK TB35 RD P1 (E-STOP) TZ-50 FROM TZ505011-311 5 - 27 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-181) C4A ZENER DIODE 5.1V DC L4A LED (CE MODELS) R14 BN65 BN67 R22B BOOM FUNCTION SPEED 10K OHM BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM BK PA8 PB4 EMERGENCY STOP WH WH BK/WH MODELS WITH ENGINE (OPTION) P2 RD BN2 ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR RD BN66 SECONDARY BOOM UP/DOWN TURNTABLE ROTATE RD/WH BK/RD POWER CABLE CR 78B TERMINAL 87A PB2 GN BK GN/WH RD RD/BK BL/BK RD/WH RD/WH BN66 RD 1 86 87 87A BL PA6 BN64 2 86 87A WH JIB HARNESS PIN 3 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 BN62 JIB HARNESS PIN 7 JIB HARNESS PIN 6 3 86 87 87A GN 4 86 87A BL/BK PB5 CR71 PLATFORM LEVEL GN GN 85 CR9 PB6 BN97 JIB BOOM UP/DOWN BL BL TB2 TB2 30 GN/BK TB1 BN67 OR/BK 85 87 PA6 LIFT CUT-OUT 30 OR/BK BN61 CR78B 85 BL OR PB3 FUNCTION ENABLE 30 RD CR87 TERMINAL 30 AND PB7 CR74 85 87 CR78B TERMINAL 86 AND PB1 PA7 RD 30 BN98 5 86 87 87A TB2 GN/WH 30 85 PB7 CR87 PLATFORM ROTATE BK 5 - 28 CR78B TERMINAL 30 AND CR74 TERMINAL 87 CR74 TERMINAL 86 WH/BK POWER CABLE CR87 TERMINAL 86 AND PA7 BN61 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) - + PA2 POWER CABLE TB2 TB3 TZ-50 ES-TZ50A Part No. 84577 September 2014 Section 5 • Schematics Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5004-182 to TZ5005-284) C4B ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C BK BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD WH WH BK/WH PA8 PB4 BN65 BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL RD TB1 POWER CABLE PIN 1 BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + BK/RD PA2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A RD RD/WH RD WH/BK BK GN/WH RD RD/BK 2 86 87 87A RD 30 RD CR78B 85 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 OR 3 86 87 87A TB8 PB3 85 4 86 87 87A TB3 TB6 9 CR71 8 7 6 5 4 3 2 1 PLATFORM LEVEL GN GN 30 GN/BK TB7 TB4 OR/BK 30 OR/BK GN TB5 LIFT CUT-OUT BL JIB HARNESS PIN 3 TB2 BL/BK PB2 BN64 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) 85 CR9 PB6 BN97 JIB BOOM UP/DOWN PA6 JIB HARNESS PIN 7 JIB HARNESS PIN 6 BL BL/BK 5 86 87 87A G7 “+” GN/WH 30 85 PLATFORM ROTATE BK Part No. 84577 TB8 CR87 TB9 ES-TZ50F TZ-50 5 - 29 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) C4B ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C BK BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD WH WH BK/WH PA8 PB4 BN65 BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL RD TB1 POWER CABLE PIN 1 BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + BK/RD PA2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A RD RD/WH RD WH/BK BK GN/WH RD RD/BK 2 86 87 87A RD 30 RD CR78B 85 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 JIB HARNESS PIN 7 JIB HARNESS PIN 6 OR 3 86 87 87A 85 4 86 87 87A BL/BK GN 85 5 86 87A CR9 8 7 6 5 4 3 2 1 PA6 BN97 G7 “+” GN/WH TB8 CR87 PLATFORM ROTATE BK 5 - 30 PB6 JIB BOOM UP/DOWN 30 85 9 TB6 CR71 GN 87 TB3 PLATFORM LEVEL 30 GN/BK BL TB8 PB3 TB7 TB4 OR/BK 30 OR/BK GN TB5 LIFT CUT-OUT BL JIB HARNESS PIN 3 TB2 BL/BK PB2 BN64 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) TB9 ES0440C TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) C4B ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C BK BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD WH P1-8 WH BK/WH P2-4 BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) P1-1 BK GN CR 9 TERMINAL 30 AND P2-6 TB1 POWER CABLE PIN 1 BL RD BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + P1-2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A P2-2 BN64 BK/RD RD RD/WH RD WH/BK BK GN/WH RD RD/BK 2 86 87 87A RD 30 RD JIB HARNESS PIN P6-2 JIB HARNESS PIN P6-5 JIB HARNESS PIN P6-4 JIB HARNESS PIN P6-7 JIB HARNESS PIN P6-6 OR CR78B 85 3 86 87 87A BL/BK 4 86 87 87A GN GN 85 5 86 87A CR9 PB6 8 7 6 5 4 3 2 1 P1-6 BN97 G7 “+” JIB BOOM UP/DOWN GN/WH 30 85 9 TB6 PLATFORM LEVEL 30 87 TB3 CR71 TB8 CR87 PLATFORM ROTATE BK Part No. 84577 TB8 P2-3 TB7 TB4 OR/BK 85 GN/BK BL TB5 LIFT CUT-OUT 30 OR/BK GN TB2 BL/BK BL JIB HARNESS PIN P6-3 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) TB9 ES0440D TZ-50 5 - 31 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - ANSI/CSA (from serial number TZ5011-132) C4B ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C BK BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD WH P1-8 WH BK/WH P2-4 BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) P1-1 BK GN CR 9 TERMINAL 30 AND P2-6 BL BN3 TB1 POWER CABLE PIN 1 BN64 ENGINE CHOKE RD SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 P1-2 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) BK/RD RD/WH WH/BK TB9 CR 78B TERMINAL 87A P2-2 BN64 GN/WH RD RD/BK 2 86 87 87A RD 30 RD JIB HARNESS PIN P6-2 JIB HARNESS PIN P6-5 JIB HARNESS PIN P6-4 JIB HARNESS PIN P6-7 JIB HARNESS PIN P6-6 OR CR78B 85 3 86 87 87A 86 87 87A BL BL/BK GN 85 5 86 87A CR9 7 6 5 4 3 2 1 P1-6 BN97 G7 “+” GN/WH TB8 CR87 PLATFORM ROTATE BK 5 - 32 PB6 JIB BOOM UP/DOWN 30 85 8 CR71 GN 87 9 TB6 PLATFORM LEVEL 30 GN/BK TB3 TB4 OR/BK 85 4 TB7 LIFT CUT-OUT 30 OR/BK GN TB8 P2-3 BL/BK BL JIB HARNESS PIN P6-3 TB2 TB5 BK TB9 ES0440G TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Drive Control Box Wiring Diagram - ANSI/CSA (to serial number TZ5004-284) BK GN/WH GN BK RD/BK RD BK/WH DL DA DE DF JC5 JOYSTICK CONTROLLER BN95 P3 FUNCTION ENABLE (OUTRIGGER RETRACT) WH/BL GN OR PP WH/BK GN OR PP WH/BL GN OR PP RD GN OR PP GY GN OR PP GY GN OR PP EMERGENCY STOP BN94 FUNCTION ENABLE (OUTRIGGER EXTEND) GN/BK RD/WH RD YL/BK YL WH/BK WH/RD BK 1 2 3 4 5 6 DK DD BN96 RD OR/BK OR WH/BK BL/BK BK AUTO LEVEL RD WH U24 BL DRIVE CONTROLS PRINTED CIRCUIT BOARD OR/BK OR WH/BK BL/BK BK DH DJ DG DN DM DC DP DB FROM TZ5005-285 REFER TO THE ELECTRICAL SCHEMATIC FOR YOUR MODEL AND SERIAL NUMBER. Part No. 84577 TZ-50 5 - 33 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (to serial number TZ5004-181) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD KS1 P1 EMERGENCY STOP KEY SWITCH RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB3 CR1 TERMINAL 86 POWER CABLE PIN 1 TURNTABLE HARNESS PIN E CR8 TERMINAL 87 CR1 TERMINAL 30 CR15 TERMINAL 30 TB3 TB10 TB7 RD BN59 BN90 (CE MODELS) CB1 CB2 15 AMP 15 AMP CHOKE L4 WH LED RD WH BN58 BN56 BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER PRIMARY BOOM UP/DOWN TB17 TB18 AUTO LEVEL BK BN54 TB9 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TURNTABLE HARNESS PIN B FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) BN93 L12 BN50 LF LED LEFT REAR OUTRIGGER PLATFORM ROTATE TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH CR73 TERMINAL 87 CR78A TERMINAL 30 WH/BK TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87 BK/WH TB27 RD WH + + H5 ALARM RD G6 HOUR METER -- TB21 CC5 RD BK TB3 PA3 TB32 TB35 ES-TZ50A 5 - 34 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - - AS/CE (to serial number TZ5004-181) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A 85 13 86 87 87A MANIFOLD HARNESS BK PIN W 14 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 PD10 86 87 87A 4700uF BK/RD RD 85 TURNTABLE HARNESS WH/BK PIN J 86 87 87A CR15 PA2 BN90 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 STARTING AID BL WH/BK 30 85 BN68 ENGINE START 30 18 PA1 CR1 BK/RD 17 PB8 C5 85 BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK 85 86 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T CR70 BL/BK CR86 SEQUENCING BK TB15 TB16 TB35 R22 1000 OHM Part No. 84577 9 86 WH 87 87A RD RD 30 85 8 86 87 87A TB31 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R MANIFOLD HARNESS RD PIN U WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK TZ-50 CR78A BK LIFT CUT-OUT WH WH 30 85 ZENER 5.1V DC 7 86 87 87A WH WH 85 6 86 87A 30 5 87 87A 86 87A 86 87A 86 87A 86 87A RD CD10 CR64 TB2 TB3 FAULT GROUND WH WH 30 85 TB7 CR76 WH 85 1 TB6 LIMIT SWITCH FAULT 30 87 WH WH/BK 30 2 TB12 TB32 TB8 TURNTABLE HARNESS PIN H CR65A U6 CUT-OUT 85 87 CR65B WH 30 3 TB16 U6 CUT-OUT 85 87 CR77 BL 30 4 TB22 DOWN ENABLE 85 87 TB35 CR28 WH WH WH 85 86 TB3 POWER SUPPLY C4A 87 TB11 FUNCTION ENABLE 30 ZENER DIODE 3.3V DC TB35 CR73 WH C4 TB34A BN55 BN58 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR ES-TZ50A 5 - 35 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-182 to TZ5004-324) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD KS1 KEY SWITCH CR1 TERMINAL 86 POWER CABLE PIN 1 TURNTABLE HARNESS PIN E TURNTABLE HARNESS PIN B CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP WH BN68 BN60 ENGINE START TB10 FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) RD OR BN90 CB1 CB2 15 AMP 15 AMP CHOKE L4 LED BN59 OR FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) WH RD WH BN58 BN56 BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) PA4 TB9 TB17 TB18 AUTO LEVEL BK BN54 TB7 BN49 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT TB3 L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES-TZ50C 5 - 36 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-182 to TZ5004-324) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS BL/BK PIN R MANIFOLD HARNESS RD PIN U 13 86 87 87A MANIFOLD HARNESS BK PIN W 14 87 87A 86 87 87A CR67 RD BK/WH 85 15 RD 30 CR8 16 87 87A BK 30 85 PB10 17 86 87 87A 86 87 87A RD C5 CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 BN68 CR1 BK/RD 30 18 PA1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J PB8 4700uF BK/RD BK/RD TB2 IGNITION BK BK TB27 BOOM EXTEND 85 MODELS PD9 WITH ENGINE (OPTION) TB12 CR69 BK/WH 86 TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK 85 86 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T TB31 CR70 BL/BK 85 CR86 SEQUENCING BK TB15 6A TB16 TB35 R22 1000 OHM PA5 WH RD RD 30 85 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 C4 ZENER 5.1V DC TZ-50 7 86 87 87A WH 6 86 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A TB6 TB7 CD10 CR76 RD CR64 TB2 PA3 FAULT GROUND WH WH 30 85 WH WH 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB12 TB32 TB8 TURNTABLE HARNESS PIN H WH 30 3 TB14 U6 CUT-OUT 85 87 CR77 BL 85 4 TB22 DOWN ENABLE 30 87 TB35 CR28 WH WH WH 85 86 TB34A BN55 TB11 POWER SUPPLY C4A 87 BK WH 85 ZENER DIODE 3.3V DC CR78A LIFT CUT-OUT 30 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A Part No. 84577 86 87A DRIVE MANIFOLD HARNESS PIN 8 PLATFORM ROTATE 30 9 87 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK DE ES-TZ50C 5 - 37 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-325 to TZ5005-284) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 OR CB1 CB2 15 AMP 15 AMP BN59 OR FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE L4 LED WH RD WH TB7 PA4 TB9 TB17 TB18 BN58 BN56 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT BN49 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH CC9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES-TZ50F 5 - 38 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5004-325 to TZ5005-284) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN U 85 13 86 87 87A MANIFOLD HARNESS BK PIN W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T 85 14 86 87 87A CR67 RD BK/WH 85 15 86 87 87A C5 BOOM EXTEND 4700uF RD 30 CR8 16 86 87 87A 30 PB10 86 87A BK/RD RD 30 18 86 87 87A BN68 CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 PA1 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J 1 CR1 BK/RD 87 PB8 5 OHM BK 85 17 TB2 IGNITION BK BK/RD TB27 (-) 85 BK TB12 CR69 BK/WH MODELS PD9 WITH ENGINE (OPTION) TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK 2 WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A WH TB6 TB7 CD10 CR76 WH RD 30 DC CR65A LIMIT SWITCH FAULT 85 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR64 TB2 PA3 FAULT GROUND WH WH 30 85 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES-TZ50F Part No. 84577 TZ-50 1 FROM TZ5005-191 2 FROM TZ5005-211 5 - 39 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5005-285 to TZ5010-144) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 OR CB1 CB2 15 AMP 15 AMP BN59 OR FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE L4 LED WH RD WH TB7 PA4 TB9 TB17 TB18 BN58 BN56 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT BN49 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 CC7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH BN51 CC9 1 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 CC3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM 1 RD G6 HOUR METER -- Contactor was moved to top position. FROM TZ5005-343 TB11 WH/BK RD + TB21 CC5 BK TB3 PA3 TB32 TB35 ES0440C 5 - 40 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5005-285 to TZ5010-144) MANIFOLD HARNESS GN/BK PIN L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN K MANIFOLD HARNESS WH PIN P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN U 85 13 86 87 87A MANIFOLD HARNESS BK PIN W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN T 85 14 86 87 87A CR67 RD BK/WH 85 15 86 87 87A C5 BOOM EXTEND 4700uF RD 30 CR8 16 86 87 87A 30 PB10 86 87A BK/RD RD 30 18 86 87 87A CR15 PA2 BN90 P1 STARTING AID BL WH/BK 30 85 BN68 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN J PA1 CR1 BK/RD 87 PB8 5 OHM BK 85 17 TB2 IGNITION BK BK/RD TB27 (-) 85 BK TB12 CR69 BK/WH MODELS PD9 WITH ENGINE (OPTION) TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN N MANIFOLD HARNESS BL PIN S GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A TB6 TB7 CD10 CR76 RD CR64 TB2 PA3 FAULT GROUND WH WH 30 85 WH WH 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR75 TB4A TURNTABLE HARNESS PIN C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES0440C Part No. 84577 TZ-50 5 - 41 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5010-145 to TZ5011-131) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD RD RD MODELS WITH ENGINE (OPTION) RD RD CR1 TERMINAL 86 TURNTABLE HARNESS PIN E POWER CABLE PIN 1 TB3 CR6 TERMINAL 30 CR15 TERMINAL 30 P1 EMERGENCY STOP RD BN68 BN60 ENGINE START FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) WH TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 OR CB1 CB2 15 AMP 15 AMP BN59 OR FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE L4 LED WH RD WH TB7 P1-4 TB9 TB17 TB18 BN58 BN56 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT BN49 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 PB5-7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH PB5-9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 PB5-3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 PB5-5 BK TB3 PA3 TB32 TB35 ES0440D 5 - 42 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5010-145 to TZ5011-131) MANIFOLD HARNESS GN/BK PIN P3-L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN P3-K MANIFOLD HARNESS WH PIN P3-P 85 11 86 87 87A 86 87 87A MANIFOLD HARNESS RD PIN P3-U 85 13 86 87 87A MANIFOLD HARNESS BK PIN P3-W SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN P3-T 85 14 86 87 87A CR67 RD BK/WH 85 15 86 87 87A C5 BOOM EXTEND 4700uF RD 30 CR8 16 86 87 87A 30 P2-10 86 87A BK/RD RD 30 18 86 87 87A CR15 P1-2 BN90 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 STARTING AID BL WH/BK 30 85 BN68 ENGINE START 85 TURNTABLE HARNESS WH/BK PIN P3-J P1-1 CR1 BK/RD 87 P2-8 5 OHM BK 85 17 TB2 IGNITION BK BK/RD TB27 (-) 85 BK TB12 CR69 BK/WH MODELS P2-9 WITH ENGINE (OPTION) TB26 PRIMARY BOOM 30 MANIFOLD HARNESS BK/WH PIN P3-V TB25 CR68 RD/BK CR86 SEQUENCING BK 86 WH 87A RD RD 30 85 TB15 6A TB16 TB35 R22 1000 OHM PA5 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN P3-R TB31 CR70 BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM HARNESS TERMINAL PA WH/BK 85 12 CR72 TERMINAL BASE TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN P3-N MANIFOLD HARNESS BL PIN P3-S GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A TB6 TB7 P4-10 CR76 RD CR64 TB2 PA3 FAULT GROUND WH WH 30 85 WH WH 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR75 TB4A TURNTABLE HARNESS PIN P3-C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A DE ES0440D Part No. 84577 TZ-50 5 - 43 Section 5 • Schematics September 2014 Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5011-132) OR/BK TB33 BK/RD CR15 TERMINAL 86 RD CR1 TERMINAL 86 RD TURNTABLE HARNESS PIN E POWER CABLE PIN 1 RD MODELS WITH ENGINE (OPTION) RD TB3 CR6 TERMINAL 30 RD RD P1 EMERGENCY STOP RD BN68 BN60 ENGINE START WH FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) CR15 TERMINAL 30 BCI + TURNTABLE HARNESS PIN B TB10 KS1 KEY SWITCH BN90 OR CB1 CB2 15 AMP 15 AMP BN59 OR FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) CHOKE L4 LED WH RD WH TB7 P1-4 TB9 TB17 TB18 BN58 BN56 PLATFORM LEVEL UP/DOWN BOOM EXTEND/RETRACT BN49 AUTO LEVEL BK BL/WH BN52 BL/WH LEFT FRONT OUTRIGGER BN54 BN93 PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) L12 BN50 LF LED LEFT REAR OUTRIGGER TB35 TB23 PB5-7 L14 LR LED BN36 JIB BOOM UP/DOWN GN/WH PB5-9 BN51 RIGHT REAR OUTRIGGER L15 RR LED BN55 SECONDARY BOOM UP/DOWN BN57 TURNTABLE ROTATE BN53 RIGHT FRONT OUTRIGGER GN/WH TB24 WH RD/WH TB4A TB20 PB5-3 RD/WH L13 RF LED OR/WH OR/WH RD TB31 GN/WH TB30 BL/BK TB25 RD/BK TB26 GN TB29 RD CR78A TERMINAL 87A BK/WH TB27 WH + H5 ALARM RD G6 HOUR METER -- TB11 WH/BK RD + TB21 PB5-5 BK TB3 PA3 TB32 TB35 ES0440G 5 - 44 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Ground Control Box Wiring Diagram - AS/CE (from serial number TZ5011-132) MANIFOLD HARNESS GN/BK PIN P3-L 10 86 87 87A 30 MANIFOLD HARNESS GN PIN P3-K 85 MANIFOLD HARNESS WH PIN P3-P 11 86 87 87A 12 86 87 87A 85 MANIFOLD HARNESS RD PIN P3-U 13 86 87 87A 85 MANIFOLD HARNESS BK PIN P3-W 14 86 87 87A TB25 CR68 TB26 CR67 PRIMARY BOOM TB12 BK/WH 30 MANIFOLD HARNESS BK/WH PIN P3-V CR70 RD 85 TB27 CR69 C5 BOOM EXTEND 4700uF (-) 15 86 87 87A RD TB2 BK/WH 30 85 P2-8 CR8 IGNITION 5 OHM BK MODELS P2-9 WITH ENGINE (OPTION) BK 16 86 87 87A P1-1 BK 30 85 BN68 CR1 ENGINE START BK/RD P2-10 BK/RD 17 86 87 87A 85 18 86 87 87A BN90 RD 30 TURNTABLE HARNESS WH/BK PIN P3-J P1-2 BK/RD 15 14 13 12 12 11 11 10 9 8 7 6 5 4A 4 3 3 3 2 2 1 P1 CR15 STARTING AID BL TB15 6A WH/BK 30 85 TB16 CR86 SEQUENCING BK TB35 R22 1000 OHM BATTERY CHARGE INDICATOR - G7 BK WH RD RD 30 PA5 TB35 CR78A BK LIFT CUT-OUT RD 8 86 87 87A RD 30 35 35 35 35 35 34 33 34A 32 32 31 30 29 28 28 27 26 25 24 23 22 22 21 20 19 18 17 16 SECONDARY BOOM 30 MANIFOLD HARNESS RD/BK PIN P3-T TB31 RD/BK 86 87A 85 PLATFORM HARNESS TERMINAL PA BL/BK 9 87 DRIVE MANIFOLD HARNESS PIN 8 PLATFORM ROTATE 30 MANIFOLD HARNESS BL/BK PIN P3-R CR72 WH/BK 85 MANIFOLD HARNESS BL PIN P3-S TB22 OUTRIGGERS 30 MANIFOLD HARNESS WH/BK PIN P3-N TERMINAL BASE GN/BK WH 85 C4 ZENER 5.1V DC 7 86 87 87A WH WH 30 85 6 86 87 87A 30 5 87 87A 86 87A BL 86 87A 86 87A 1 86 87 87A WH TB6 TB7 P4-10 CR76 WH RD 85 DC CR65A LIMIT SWITCH FAULT 30 6A TB12 TB32 TB8 TB15 WH/BK 30 2 CR65B U6 CUT-OUT 85 87 TB14 TURNTABLE HARNESS PIN H WH 30 3 TB22 U6 CUT-OUT 85 87 CR77 BL 85 4 TB18 U16B DOWN ENABLE 30 87 TB17 CR28 WH WH WH 85 86 TB35 AUTO LEVEL POWER SUPPLY C4A ZENER DIODE 3.3V DC TB34A BN55 TB11 CR64 TB2 PA3 FAULT GROUND WH WH 30 85 CR75 TB4A TURNTABLE HARNESS PIN P3-C LEVEL SENSOR 6A NOTE: DIODES ARE 2 AMP UNLESS OTHERWISE MARKED 6A P3-X 1 200 OHM 6A RD + P1 (E-STOP) DE ES0440G 1 Part No. 84577 TZ-50 FROM TZ505011-311 5 - 45 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - AS/CE (to serial number TZ5004-181) C4A ZENER DIODE 5.1V DC L4A LED (CE MODELS) R14 BN65 BN67 R22B BOOM FUNCTION SPEED 10K OHM BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM BK PA8 PB4 EMERGENCY STOP WH WH BK/WH MODELS WITH ENGINE (OPTION) P2 RD BN2 ENGINE START RD OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR RD BN66 SECONDARY BOOM UP/DOWN TURNTABLE ROTATE RD/WH BK/RD POWER CABLE CR 78B TERMINAL 87A PB2 GN BK GN/WH RD RD/BK BL/BK RD/WH RD/WH BN66 RD 1 86 87 87A BL PA6 BN64 2 86 87A WH JIB HARNESS PIN 3 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 BN62 JIB HARNESS PIN 7 JIB HARNESS PIN 6 3 86 87 87A GN 4 86 87A BL/BK PB5 CR71 PLATFORM LEVEL GN GN 85 CR9 PB6 BN97 JIB BOOM UP/DOWN BL BL TB2 TB2 30 GN/BK TB1 BN67 OR/BK 85 87 PA6 LIFT CUT-OUT 30 OR/BK BN61 CR78B 85 BL OR PB3 FUNCTION ENABLE 30 RD CR87 TERMINAL 30 AND PB7 CR74 85 87 CR78B TERMINAL 86 AND PB1 PA7 RD 30 BN98 5 86 87 87A TB2 GN/WH 30 85 PB7 CR87 PLATFORM ROTATE BK 5 - 46 CR78B TERMINAL 30 AND CR74 TERMINAL 87 CR74 TERMINAL 86 WH/BK POWER CABLE CR87 TERMINAL 86 AND PA7 BN61 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) - + PA2 POWER CABLE TB2 TB3 TZ-50 ES-TZ50A Part No. 84577 September 2014 Section 5 • Schematics Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5004-182 to TZ5005-284) C4A ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C L4A BK LED LIMIT SWITCH HARNESS OR TERMINAL 3 BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD OR PA4 PA8 PB4 WH WH BK/WH BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD POWER CABLE PIN 1 RD PA12 OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + BK/RD PA2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A RD RD/WH RD WH/BK BK GN/WH RD RD/BK 2 86 87 87A RD 30 RD CR78B 85 JIB HARNESS PIN 3 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 JIB HARNESS PIN 7 JIB HARNESS PIN 6 3 86 87 87A 85 4 86 87 87A BL/BK GN 85 5 87 87A CR9 8 7 6 5 4 3 2 1 PA6 BN97 G7 “+” GN/WH TB8 CR87 PLATFORM ROTATE (OPTION) BK Part No. 84577 PB6 JIB BOOM UP/DOWN 30 85 9 TB6 CR71 GN 86 TB3 PLATFORM LEVEL 30 GN/BK BL TB8 PB3 TB7 TB4 OR/BK 30 OR/BK GN TB5 LIFT CUT-OUT BL OR TB2 BL/BK PB2 BN64 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) TB9 ES-TZ50F TZ-50 5 - 47 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5005-285 to TZ5010-144 ) C4A ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C L4A BK LED LIMIT SWITCH HARNESS OR TERMINAL 3 BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD OR PA4 PA8 PB4 WH WH BK/WH BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD POWER CABLE PIN 1 OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) PA1 BK GN CR 9 TERMINAL 30 AND PB6 BL BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + BK/RD PA2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A RD RD/WH RD WH/BK BK GN/WH RD RD/BK 2 86 87 87A RD 30 RD CR78B 85 JIB HARNESS PIN 3 JIB HARNESS PIN 2 JIB HARNESS PIN 5 JIB HARNESS PIN 4 JIB HARNESS PIN 7 JIB HARNESS PIN 6 3 86 87 87A 85 4 86 87 87A BL/BK GN 85 5 87 87A CR9 8 7 6 5 4 3 2 1 PA6 BN97 G7 “+” GN/WH TB8 CR87 PLATFORM ROTATE (OPTION) BK 5 - 48 PB6 JIB BOOM UP/DOWN 30 85 9 TB6 CR71 GN 86 TB3 PLATFORM LEVEL 30 GN/BK BL TB8 PB3 TB7 TB4 OR/BK 30 OR/BK GN TB5 LIFT CUT-OUT BL OR TB2 BL/BK PB2 BN64 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) TB9 ES0440C TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5010-145 to TZ5011-131) C4A ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C L4A BK LED LIMIT SWITCH HARNESS OR TERMINAL 3 BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD OR P1-4 P1-8 WH BK/WH P2-4 WH BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD POWER CABLE PIN 1 OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) P1-1 BK CR 9 TERMINAL 30 AND P2-6 GN BL BN3 G7 BN64 ENGINE CHOKE BATTERY CHARGE INDICATOR SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 - + P1-2 TB1 POWER CABLE PIN 2 TB9 CR 78B TERMINAL 87A P2-2 BN64 BK/RD RD RD/WH RD WH/BK BK GN/WH RD RD/BK JIB HARNESS PIN P6-2 JIB HARNESS PIN P6-5 JIB HARNESS PIN P6-4 JIB HARNESS PIN P6-7 JIB HARNESS PIN P6-6 2 86 87 87A RD 30 RD OR CR78B 85 3 86 87 87A TB5 TB8 P2-3 GN 86 87 87A BL BL/BK GN 85 5 87 87A CR9 PB6 7 6 5 4 3 2 1 PA6 BN97 G7 “+” JIB BOOM UP/DOWN GN/WH 30 85 8 CR71 GN 86 9 TB6 PLATFORM LEVEL 30 GN/BK TB3 TB4 OR/BK 85 4 TB7 LIFT CUT-OUT 30 OR/BK TB8 CR87 PLATFORM ROTATE (OPTION) BK Part No. 84577 TB2 BL/BK BL JIB HARNESS PIN P6-3 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) TB9 ES0440D TZ-50 5 - 49 Section 5 • Schematics September 2014 Platform Control Box Wiring Diagram - AS/CE (from serial number TZ5011-132) C4A ZENER DIODE 5.1V DC R14 BOOM FUNCTION SPEED 5.6K OHM 10K OHM R22C L4A BK LED LIMIT SWITCH HARNESS OR TERMINAL 3 BN65 BN67 R22B BOOM EXTEND/RETRACT PLATFORM LEVEL 5.6K OHM P2 EMERGENCY STOP RD OR P1-4 P1-8 WH BK/WH P2-4 WH BN2 MODELS WITH ENGINE (OPTION) ENGINE START RD POWER CABLE PIN 1 OR/BK BN97 BN63 BN98 JIB BOOM UP/DOWN PRIMARY BOOM UP/DOWN PLATFORM ROTATE (OPTION) TB6 BN62 FUNCTION ENABLE (BOOM UP, EXTEND, TURNTABLE AND PLATFORM ROTATE RIGHT) P1-1 BK CR 9 TERMINAL 30 AND P2-6 GN BL BN3 BN64 ENGINE CHOKE SECONDARY BOOM UP/DOWN BN66 RD TURNTABLE ROTATE RD TB4 TB3 TB1 BN61 P1-2 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) BK/RD RD/WH WH/BK TB9 CR 78B TERMINAL 87A P2-2 BN64 GN/WH RD RD/BK JIB HARNESS PIN P6-2 JIB HARNESS PIN P6-5 JIB HARNESS PIN P6-4 JIB HARNESS PIN P6-7 JIB HARNESS PIN P6-6 2 86 87 87A RD 30 RD CR78B 85 OR 3 86 87 87A GN 85 4 86 87 87A BL BL/BK GN 85 5 87 87A CR9 PB6 7 6 5 4 3 2 1 PA6 BN97 G7 “+” JIB BOOM UP/DOWN GN/WH 30 85 8 CR71 GN 86 9 TB6 PLATFORM LEVEL 30 GN/BK TB3 TB4 OR/BK 30 OR/BK TB7 LIFT CUT-OUT TB8 CR87 PLATFORM ROTATE (OPTION) BK 5 - 50 TB8 P2-3 BL/BK BL JIB HARNESS PIN P6-3 TB2 TB5 BK TB9 ES0440G TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Drive Control Box Wiring Diagram - AS/CE (to serial number TZ5004-284) BK GN/WH GN BK RD/BK RD BK/WH DL DA DE DF JC5 JOYSTICK CONTROLLER P3 EMERGENCY STOP WH/BK GN OR PP RD GN OR PP WH/BL GN OR PP WH/BL GN OR PP GY GN OR PP GY GN OR PP OR/BK RD YL/BK YL WH/BK WH/RD BK 1 2 3 4 5 6 RD OR/BK OR WH/BK BL/BK BK OR WH/BK BL/BK BK DN DM DC DP DB U24 DRIVE CONTROLS PRINTED CIRCUIT BOARD FROM TZ5005-285 REFER TO THE ELECTRICAL SCHEMATIC FOR YOUR MODEL AND SERIAL NUMBER. Part No. 84577 TZ-50 5 - 51 Section 5 • Schematics September 2014 This page intentionally left blank. 5 - 52 TZ-50 Part No. 84577 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (to serial number TZ5004-181) 5 - 53 5 - 54 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (to serial number TZ5004-181) A B C D E F G H I J K L M TO 1 N A (PLATFORM CONTROLS) (PLATFORM CONTROLS) TO B (DRIVE CONTROLS) (DRIVE CONTROLS) - NOTE MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF 2 TO N.C.H.O. N.O.H.C. N.C.H.O. FB DG DH DJ DK OR/RD WH GN/BK DF GN/BK RD DE CD11 BL BL BOOM DOWN CD9 BK/WH WH LS18A RD/BK PA6 CD10 WH/BK DD N.O.H.C. RD RD/WH DC PA5 RD/WH PA4 PA3 WH/BK WH/RD DB PA2 OR WH PA1 BK PA11 BK/RD PA10 BK 3 BK WH GN BK WH GN DA MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF BOOM DOWN FLASHING BEACON (OPTION) 2 - NOTE - LS18 FB1 1 C (AUTO-LEVEL) PA7 PA8 PA9 TB1 3 TB4 TB2 TB3 BN59 4 BN68 BN90 ENGINE START CHOKE GROUND PLATFORM MODELS WITH ENGINE (OPTION) KS1 KEY SWITCH BN60 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) H5 L4 ALARM LED TB8 TB9 30 6 86 87A 87 85 TB10 TB11 TB5 CR64 30 86 2 FAULT GROUND 87A 30 4 86 87A 87 85 85 TB13 CR77 TB6 87 DOWN ENABLE R22 BN49 1000 OHM AUTO LEVEL TB14 TB7 5 87A CB1 15 AMP 30 85 87A 16 87 86 30 85 87A 17 87 86 CR8 CR1 CR15 IGNITION ENGINE START STARTING AID CB2 U16B 85 30 1 86 87A 87 85 87A TIME DELAY (10 TO 30 SECONDS) + - LOAD TB35 3 86 30 5 86 87 85 87A 87 85 CR75 CR76 LEVEL SENSOR LIMIT SWITCH FAULT BN51 LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER L12 L13 L14 L15 LF LED RF LED LR LED RR LED CR65B C5 4700uF 30 POWER SUPPLY 18 87A 87 86 30 7 86 85 87A 87 85 CR86 SEQUENCING U6 CUTOUT C4A C4 ZENER DIODE 3.3V DC ZENER DIODE 5.1V DC TB22 U16A TIME DELAY (0.1 TO 10 SECONDS) TB20 TB23 TB21 TB24 TB28 + - LOAD 6 87 86 BN50 RIGHT FRONT OUTRIGGER CR28 TB15 15 BN53 LEFT FRONT OUTRIGGER TB18 P1 30 BN52 TB32 U6 CUTOUT 30 TB17 TB16 CR65A EMERGENCY STOP GROUND CONTROL BOX FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB12 GROUND CONTROL BOX TB35 GN/WH 15 AMP F + + + AC INPUT - BATTERY CHARGER CC3 CC4 CD3 CD4 CC5 CC6 CD5 CD6 CC7 CC8 CD7 CD8 Y35 Y36 Y33 Y34 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER N.C.H.O. N.C.H.O. CC9 CC10 (AUTO-LEVEL) T2 B- U9 CD2 GN/WH B+ CD1 S2 A1 B CC1 CC2 BL/WH M3 STARTER MOTOR 8 OR/WH M3 7 GN/WH + U26 IGNITION 6 OR/WH S7 LEVEL SENSOR 3 - 5 BL/WH MOTOR M5 F9 50 AMP POWER RELAY 3 WH/BK 275A FUSE PR5 50 AMP 4 RD/WH G 2 WH F9A M5 F6 N.O. BK - 1 RD CHOKE SOLENOID H BK Q7 J A RD/WH C RD - 8 C WH 4-6V BATTERY RD/WH D1 ALTERNATOR B5 A PB12 BL PB11 WH/BK PB10 RD BK PB9 BK/RD RD PB8 BK D WH E RD 7 B U6 1 0-5V DC KEY OUTRIGGERS SHOWN IN STOWED POSITION N.C.H.O. N.C.H.O. LS12 LS13 LS14 LS15 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER MOTOR CONTROLLER ES-TZ50A + 5 - 54 TZ-50 Part No. 84577 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (to serial number TZ5004-181) N M L K J I H G A F E D C B A TO A (PLATFORM CONTROLS) (PLATFORM CONTROLS) (DRIVE CONTROLS) (DRIVE CONTROLS) B TO C 1 B (AUTO-LEVEL) 2 - NOTE - FUNCTION ENABLE LIFT CUT-OUT RD/WH TB30 CR78A OR/WH TB33 CR73 BL/WH 85 GN/WH 87 WH 87A BK PLATFORM ROTATE (OPTION) DM WH/BK PLATFORM LEVEL UP/DOWN DL RD BN93 86 PB6 OR/BK BN58 9 OR PB7 30 TURNTABLE ROTATE TB31 PB4 GN/WH 85 PB5 GN 87 BN57 PB3 GN/WH 86 PB2 BK/WH 87A 8 PB1 OR/BK 30 RD/BK DP BL/BK BL/BK WH/BK MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF DN 2 3 1 4 8 7 6 5 S10 S9 LEFT/RIGHT AXIS LEVEL SENSOR FRONT/REAR AXIS LEVEL SENSOR 4 2 3 1 4 GROUND CONTROL BOX TB34A BN55 BN54 BN56 BN36 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/RETRACT JIB BOOM UP/DOWN TB25 TB26 3 1 3 4 CR66 LEVEL SENSOR RELAY YL CR61 86 30 AUTO LEVEL SYSTEM RELAY 87A TB29 TB27 2 AUTO LEVEL 87 85 TB32 86 30 RD 5 RD TB28 30 10 30 85 87A 11 86 30 85 87A 12 86 30 85 87A 13 86 30 85 87A 14 86 GN YL 86 30 86 30 86 30 87A 87 85 86 30 + 86 GN 87A 87 87 87 87 87 85 87A G6 CR72 CR70 CR68 CR67 CR69 HOUR METER OUTRIGGER TURNTABLE ROTATE SECONDARY BOOM PRIMARY BOOM BOOM EXTEND 87 85 87A 87 85 87A 87 85 87A 87 85 6 TB35 TB34 N R P S T OUTRIGGER EXTEND ROTATE LEFT SECONDARY DOWN PRIMARY DOWN BOOM RETRACT Y39 Y24 Y53 Y22 Y26 OUTRIGGER RETRACT ROTATE RIGHT SECONDARY UP PRIMARY UP BOOM EXTEND 8 7 Y50 Y58 DRIVE FWD/REV LEFT PROPORTIONAL DRIVE RIGHT Y50A Y59 DRIVE FWD/REV RIGHT PROPORTIONAL DRIVE LEFT BL Y25 5 3 OR/BK Y21 1 OR Y52 2 WH BK/WH Y23 BK RD RD/BK BL/BK BL WH/BK WH GN/BK GN Y40 ES-TZ50A W V U WH M L BK K Y11 7 BRAKE RELEASE (DRIVE) 8 BRN Part No. 84577 TZ-50 5 - 55 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (to serial number TZ5004-181) 5 - 55 5 - 56 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (to serial number TZ5004-181) N M L K J I H G F E D C B A A 1 B 2 P3 P2 EMERGENCY STOP EMERGENCY STOP 2 3 4 5 6 7 G7 F BATTERY CHARGE INDICATOR E PA6 PA8 PA7 PB1 PB5 PB7 PB4 PB3 PB2 DRIVE CONTROL BOX 1 BN94 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) JOYSTICK CONTROLLER BN95 FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) BN96 AUTOLEVEL PLATFORM CONTROL BOX PB6 3 CR74 H1 FUNCTION ENABLE ALARM JC5 GN PA3 BL/BK PA9 RD/BK PA4 BK/WH WH PA5 GN/WH OR/RD PA1 OR/BK OR PA2 WH/BK WH/RD 3 BL BK 2 GN/BK BK/RD 1 RD/WH BK DD GN DK WH DG RD/WH DJ GN/BK DH BL DP WH DB RD DL BL/BK DC BK DM GN/WH DN WH/BK DE OR DA OR/BK RD/BK GN BK/WH DF 30 1 86 87A 87 85 BN2 ENGINE START BN3 CHOKE BN61 BN62 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) FUNCTION ENABLE (BOOM UP, BOOM EXTEND TURNTABLE AND PLATFORM ROTATE RIGHT) 4 PLATFORM ROTATE (OPTION) BN66 R22B MODELS WITH ENGINE (OPTION) CR78B TURNTABLE ROTATE 5.6K OHM LIFT CUT-OUT RD 2 86 87A 87 85 BN98 PLATFORM LEVEL PLATFORM ROTATE 5 WH R14 BK RESISTOR 0-10K OHM 30 BN67 C4B BN97 BN64 BN63 BN65 JIB BOOM UP/DOWN SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/ RETRACT ZENER DIODE 5.1V DC 6 CR9 30 4 86 87 85 30 5 86 87A 4 1 2 3 1 4 87A 87 85 6 5 CR87 30 3 86 87A 87 85 PLATFORM ROTATE JIB BOOM UP/DOWN 7 2 3 OR/BK Y62 Y19 JIB BOOM RETRACT PLATFORM ROTATE LEFT PLATFORM LEVEL DOWN PLATFORM LEVEL OR GN GN/BK GN GN/BK Y60 CR71 Y61 Y63 Y20 JIB BOOM EXTEND PLATFORM ROTATE RIGHT PLATFORM LEVEL UP 7 ES-TZ50A Part No. 84577 TZ-50 8 5 - 57 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (to serial number TZ5004-181) 5 - 57 5 - 58 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5004-182 to TZ5005-210) 5 - 59 5 - 60 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5004-182 to TZ5005-210) A B C D E F G H I J K L M TO (PLATFORM CONTROLS) 1 N A (PLATFORM CONTROLS) TO (DRIVE CONTROLS) B (DRIVE CONTROLS) - NOTE MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF 2 TO N.C.H.O. N.O.H.C. N.C.H.O. FB DK OR/RD DJ GN/BK DH BL DG GN/BK DF RD DE CD11 WH BL BOOM DOWN CD9 BK/WH WH LS18A RD/BK PA6 CD10 WH/BK DD N.O.H.C. RD RD/WH DC PA5 RD/WH PA4 PA3 WH/BK DB PA2 WH/RD OR WH PA1 BK PA11 BK/RD PA10 BK 3 BK WH GN BK WH GN DA MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF BOOM DOWN FLASHING BEACON (OPTION) 2 - NOTE - LS18 FB1 1 C (AUTO-LEVEL) PA7 PA8 PA9 TB1 TB4A 3 TB2 TB4 6A 6A TB3 BN59 GROUND CONTROL BOX 4 BN68 BN90 ENGINE START CHOKE GROUND PLATFORM KEY SWITCH H5 L4 ALARM LED GROUND CONTROL BOX FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB8 TB10 TB9 30 6 86 87A 87 85 CR64 MODELS WITH ENGINE (OPTION) KS1 BN60 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) 6A 6A TB11 FAULT GROUND 30 86 2 CR77 TB5 30 87A 87 TB13 85 4 R22 DOWN ENABLE 86 87A 5 87 BN50 BN51 RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER AUTO LEVEL TB17 TB16 85 BN53 LEFT FRONT OUTRIGGER BN49 1000 OHM TB14 TB7 BN52 L12 L13 L14 L15 LF LED RF LED LR LED RR LED TB18 TB32 CR65A U6 CUTOUT EMERGENCY STOP 30 87A 87 86 30 85 87A 16 87 86 30 85 87A 17 87 86 85 U16B TIME DELAY CB1 15 AMP CR8 CR1 CR15 IGNITION ENGINE START STARTING AID CB2 30 1 86 30 3 86 30 5 86 87A 87 85 87A 87 85 87A 87 85 + C5 4700uF 30 18 86 30 7 86 85 87A 87 85 TB22 U16A TIME DELAY TB20 (0.1 TO 10 SECONDS) (10 TO 30 SECONDS) - POWER SUPPLY LOAD TB35 CR75 CR76 LEVEL SENSOR LIMIT SWITCH FAULT 87A 87 CR86 CR65B SEQUENCING U6 CUTOUT C4A C4 ZENER DIODE 3.3V DC ZENER DIODE 5.1V DC TB23 TB21 TB24 TB28 + - LOAD 6 15 LEVEL SENSOR RELAY P1 TB12 CR28 TB15 TB35 GN/WH 15 AMP F + U9 BATTERY CHARGER TZ-50 + + CC3 CC4 CD3 CD4 CC5 CC6 CD5 CD6 CC7 CC8 CD7 CD8 (AUTO-LEVEL) Y35 Y36 Y33 Y34 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER N.C.H.O. N.C.H.O. T2 3 OUTRIGGERS SHOWN IN STOWED POSITION KEY 0-5V DC U6 MOTOR CONTROLLER + 5 - 60 CD2 GN/WH B- CD1 BL/WH B+ B CC1 CC2 A1 S2 AC INPUT - 8 OR/WH M3 STARTER MOTOR 7 GN/WH M3 6 OR/WH + U26 IGNITION 5 BL/WH S7 LEVEL SENSOR 1 - 3 WH/BK MOTOR M5 F9 50 AMP POWER RELAY 4 RD/WH 275A FUSE PR5 50 AMP 2 WH G M5 F6 N.O. BK - F9A 1 RD CHOKE SOLENOID J BK Q7 H A RD/WH C WH/BK - 8 C BL 4-6V BATTERY A RD D1 ALTERNATOR B5 PB12 WH PB11 RD/WH PB10 RD PB9 BK/RD PB8 BK BK RD D WH E RD 7 B Part No. 84577 ES-TZ50D N.C.H.O. N.C.H.O. LS12 LS13 LS14 LS15 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER CC9 CC10 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5004-182 to TZ5005-210) N M L K J I H G A F E D C B A TO A (PLATFORM CONTROLS) (PLATFORM CONTROLS) (DRIVE CONTROLS) (DRIVE CONTROLS) B TO C 1 B (AUTO-LEVEL) 2 - NOTE - OR/WH RD/WH 85 BL/WH 87 GN/WH 87A WH TB31 BK 86 DM WH/BK 9 DL RD 30 PB6 OR/BK PB7 BN58 BN57 TURNTABLE ROTATE OR PB4 GN/WH PB5 GN PA12 GN/WH PB3 BK/WH PB2 OR/BK PB1 RD DP RD/BK BL/BK WH/BK BL/BK MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF DN 2 3 1 4 8 7 6 5 S10 S9 LEFT/RIGHT AXIS LEVEL SENSOR FRONT/REAR AXIS LEVEL SENSOR AUTO LEVEL 3 BN93 PLATFORM LEVEL UP/DOWN PLATFORM ROTATE (OPTION) TB33 4 TB30 2 3 1 4 GROUND CONTROL BOX CR78A LIFT CUT-OUT TB34A BN55 BN54 BN56 BN36 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/RETRACT JIB BOOM UP/DOWN TB25 TB26 3 1 4 CR66 LEVEL SENSOR RELAY YL CR61 86 30 AUTO LEVEL SYSTEM RELAY 87A TB29 TB27 2 87 85 TB32 86 30 RD 5 RD TB28 30 10 30 85 87A 11 86 30 85 87A 12 86 30 85 87A 13 86 30 85 87A 14 86 GN YL 86 30 86 30 86 30 87A 87 85 86 30 + 86 GN 87A 87 87 87 87 87 85 G6 CR72 CR70 CR68 CR67 CR69 HOUR METER OUTRIGGER TURNTABLE ROTATE SECONDARY BOOM PRIMARY BOOM BOOM EXTEND 87A 87 85 87A 87 85 87A 87 85 87A 87 85 6 TB35 TB34 N R P S T OUTRIGGER EXTEND ROTATE LEFT SECONDARY DOWN PRIMARY DOWN BOOM RETRACT Y39 Y24 Y53 Y22 Y26 OUTRIGGER RETRACT ROTATE RIGHT SECONDARY UP PRIMARY UP BOOM EXTEND 8 7 Y50 Y58 DRIVE FWD/REV LEFT PROPORTIONAL DRIVE RIGHT Y50A Y59 DRIVE FWD/REV RIGHT PROPORTIONAL DRIVE LEFT BL Y25 5 3 OR/BK Y21 1 OR Y52 2 WH BK/WH Y23 BK RD RD/BK BL/BK BL WH WH/BK GN/BK GN Y40 ES-TZ50D W V U WH M L BK K Y11 7 BRAKE RELEASE (DRIVE) 8 BRN Part No. 84577 TZ-50 5 - 61 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5004-182 to TZ5005-210) 5 - 61 5 - 62 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5004-182 to TZ5005-210) N M L K J I H G F E D C B A A 1 B 2 EMERGENCY STOP 3 4 5 6 7 JC5 1 BN94 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) JOYSTICK CONTROLLER BN95 FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) BN96 AUTOLEVEL PLATFORM CONTROL BOX PA8 PA7 PB1 PA12 PB5 PB7 PB4 PB3 PB2 GN P2 EMERGENCY STOP PA6 BL/BK PA3 RD/BK PA9 BK/WH PA4 GN/WH WH PA5 OR/BK OR/RD PA1 RD OR PA2 WH/BK WH/RD 3 BL BK 2 GN/BK BK/RD 1 RD/WH BK DD GN DK WH DG RD/WH DJ GN/BK DH WH DL BL DB RD DP GN/WH BK DC P3 2 DRIVE CONTROL BOX DM BL/BK DN WH/BK DE OR DA OR/BK RD/BK GN BK/WH DF PB6 3 G7 F H1 BATTERY CHARGE INDICATOR E ALARM TB1 L4A LED BN2 ENGINE START BN3 CHOKE BN61 BN62 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) FUNCTION ENABLE (BOOM UP, BOOM EXTEND TURNTABLE AND PLATFORM ROTATE RIGHT) TB4 TB3 6A TB2 BN66 R22B MODELS WITH ENGINE (OPTION) TURNTABLE ROTATE 5.6K OHM BN98 PLATFORM LEVEL PLATFORM ROTATE RD 87A 2 86 87 85 TB6 TB8 5 TB7 BK R22C C4B BN67 LIFT CUT-OUT WH R14 RESISTOR 0-10K OHM CR78B 30 TB5 4 PLATFORM ROTATE (OPTION) 6A 5.6K OHM BN97 BN97 BN64 BN63 BN65 JIB BOOM UP/DOWN JIB BOOM UP/DOWN SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/ RETRACT ZENER DIODE 5.1V DC 6 CR9 30 4 86 87 85 30 5 86 87A 87A 87 85 CR87 30 3 86 87A 87 85 PLATFORM ROTATE JIB BOOM UP/DOWN CR71 PLATFORM LEVEL TB9 4 1 2 3 1 4 3 Y60 Y62 Y19 JIB BOOM RETRACT PLATFORM ROTATE LEFT PLATFORM LEVEL DOWN OR OR/BK N.O. (SWITCH SHOWN IN UNLOADED POSITION) 2 GN N.C. 7 GN/BK LOAD SENSE GN GN/BK LS19 6 5 Y61 Y63 Y20 JIB BOOM EXTEND PLATFORM ROTATE RIGHT PLATFORM LEVEL UP 7 ES-TZ50D Part No. 84577 TZ-50 8 5 - 63 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5004-182 to TZ5005-210) 5 - 63 5 - 64 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5005-211 to TZ5005-284) 5 - 65 5 - 66 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5005-211 to TZ5005-284) A B C D E F G H I J K L WHT GRN BLK BLK BLK/RED WHT To Page 3 of 3 ORG WHT/RED ORG/RED RED/WHT BLU GRN/BLK 1 ORG/RED BLU/BLK BLU DE GRN/BLK CD10 CD11 GRN/BLK WHT RED BLU BLK/WHT CD9 WHT DC DD PA6 PA5 RED/BLK PA4 PA3 WHT/BLK DB PA2 PA1 RED PA11 RED/WHT RED/WHT WHT/BLK WHT/RED PA10 ORG WHT FLASHING BEACON OPTION BLK DA 3 WHT 2 FB BLK FB1 GRN 1 BLK/RED BLK BLK GRN WHT 2 DOWN LIMIT SWITCHES SHOWN IN STOWED POS. DF DG DH DJ DK PA7 PA8 DP GROUND CONTROL BOX PA9 TB4A TB2 TB4 3 TB3 CHOKE BN59 FAULT ALARM L4 PLAT ENGINE OPTION TB7 U6 CUTOUT 87A 87 85 87A 87 85 CR77 CR76 30 5 86 30 18 86 87A 87 85 87A 87 85 TB22 30 7 86 87A 87 85 + 30 8 86 - 87A 87 85 CR28 C4A 3.3V L13 L14 L15 RF LED LR LED RR LED U16A 0 .1-10 SEC TIME DELAY TB20 TB21 TB23 TB24 CR61 C4 5.1V CD1 CD2 CD3 CD5 CD7 CC7CC8 CD8 CC9 CC10 Y34 WHT GRN/WHT RED Y33 BLU/WHT RED Y36 CD6 GRN/WHT CC5CC6 ORG/WHT RED RED/WHT Y35 CD4 BLU/WHT CC3 CC4 ORG/WHT CC2 RED AUTO LEVEL 0-5 VDC SIGNAL 5 6 7 8 CC1 WHT 4 GRN/WHT BLU/WHT ORG/WHT RED/WHT BLK 2 RED/WHT 1 J LEVEL SENSOR S7 L12 LF LED TB28 WHT/BLK A TB17 CR86 BLU C AUTO LEVEL TB18 H F BN90 WHT C RIGHT REAR OUTRIGGER RED A F9 BLK CHOKE SOLENOID + - PB12 RED BLK WHT PB11 BN51 LEFT REAR OUTRIGGER TB16 CR65B WHT RED PB10 BLK/RED RED/WHT RED PB9 PB8 RED D BLK E BN50 RIGHT FRONT OUTRIGGER TB14 87A 87 85 87A 87 85 BN53 LEFT FRONT OUTRIGGER LOAD 87A 87 85 BN52 TB13 TB32 CR65A 30 3 86 TB11 1K OHM 30 4 86 U6 CUTOUT 30 1 86 TB12 TB10 TB9 30 6 86 CAPACITOR 4700uF Q7 PR5 B5 1 B- B B1 250 AMP 24V BATT 3 T2 TZ-50 Part No. 84577 S2 B+ A1 MOTOR CONTROLLER 8 5 - 66 TB8 15 AMP B BN60 FUNCTION ENABLE TB15 LS FAULT LEVEL SENSOR CR15 - 30 2 86 CB1 15 AMP 7 CR1 87A 87 85 + FAULT GROUND CR8 87A 87 85 30 17 86 LOAD 87A 87 85 30 16 86 CHOKE P1 30 15 86 START IGNITION 5 10-30 SEC TIME DELAY U16B CB2 TB5 CR64 KS1 6 DOWN ENABLE BN90 ENGINE START GROUND 4 BN68 MOTOR OUTRIGGER LIMIT SWITCHES OUTRIGGERS SHOWN IN STOWED POSITION (FORCED OPEN) LS12 LS13 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LS14 LS15 LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER ES-TZ50F M N September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5005-211 to TZ5005-284) N M L K PB5 F GRN/WHT PB4 G GRN PB3 H ORG/BLK PB2 BLK/WHT PB1 I RED/BLK BLUE/BLK WHT/BLK GROUND CONTROL BOX J PB6 E D C B A WHT/BLK BLU/BLK RED/BLK BLK/WHT To Page 3 of 3 ORG/BLK GRN GRN/WHT 1 PB7 2 CR78A LIFT CUTOUT BN57 TURNTABLE ROTATE TB31 DRIVE CONTROL BOX (OPTION) BN93 30 9 86 PLATFORM ROTATE (OPTION) TB30 BN93 PLATFORM LEVEL UP/DOWN 87A 87 85 1 TB33 EMERGENCY STOP TB34A BN95 DOWN ENABLE UP ENABLE BN96 AUTO LEVEL 2 JC5 JOYSTICK CONTROLLER 3 4 5 3 6 P3 BN55 BN54 BN56 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN EXTEND/RETRACT TB25 TB32 TB28 TB12 TB22 BN96 BN36 JIB BOOM UP/DOWN BOOM TB26 TB29 TB27 4 TB28 CR72 GRN/WHT BLK BLU/BLK WHT/BLK DN 7 5 5 8 ORG/BLK 6 Y59 BRAKE RELEASE LEFT PROPORTIONAL RIGHT PROPORTIONAL Y50A ORG/BLK ORG ORG FWD/REV RIGHT BOOM EXTEND BOOM RETRACT PRIMARY UP PRIMARY DOWN SECONDARY UP SECONDARY DOWN ROTATE RIGHT ROTATE LEFT OUTRIGGER RETRACT OUTRIGGER EXTEND Y50 WHT BRN DM 3 GRN/WHT Y22 FWD/REV LEFT Y53 Y24 WHT BLK BLK/WHT Y26 Y39 2 DL 1 Y25 Y21 ORG W V RED RED/BLK Y52 DN DM DC DP DB DL ORG/BLK U WHT T BLUE Y40 BLUE/BLK WHT WHT/BLK GRN/BLK GRN Y23 S DH DJ RED R P DG BLU N GRN/BLK M L DK TB34 TB35 K RED/WHT 87A 87 85 BLK/WHT 87A 87 85 DD 30 14 86 RED/BLK 87A 87 85 30 13 86 DA DE DF GRN 87A 87 85 30 12 86 BOOM EXTEND 87A 87 85 30 11 86 CR69 CR67 PRIMARY BOOM 30 10 86 CR68 SECONDARY BOOM TURNTABLE ROTATE OUTRIGGER + HM CR70 Y11 Y58 7 ES-TZ50F 8 Part No. 84577 TZ-50 5 - 67 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5005-211 to TZ5005-284) 5 - 67 5 - 68 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5005-211 to TZ5005-284) N M L K J I F E D C B A 1 2 GRN/WHT PB4 PB3 GRN ORG/BLK PB1 PB2 BLK/WHT RED/BLK PA7 PA8 BLU/BLK WHT/BLK PA6 GRN/BLK PA4 PA5 PA9 BLU PA3 RED/WHT PA2 ORG PA1 WHT 3 BLK/RED 2 BLK EMERGENCY STOP BLK GRN WHT 1 ORG/RED From Page 2 of 3 WHT/BLK BLU/BLK RED/BLK BLK/WHT ORG/BLK GRN GRN/WHT G WHT/RED From Page 1 of 3 WHT GRN BLK BLK BLK/RED WHT ORG WHT/RED ORG/RED RED/WHT BLU GRN/BLK H PB5 PB6 3 PB7 G7 BCI P2 H1 TB1 BN61 BN62 DOWN FUNCTION ENABLE UP FUNCTION ENABLE L4A CR78B BN66 LED TB3 LIFT CUTOUT TURNTABLE ROTATE TB5 TB2 BN2 BN3 TB4 START CHOKE ENGINE OPTION 30 2 86 BN98 PLATFORM ROTATE TB6 87A 87 85 TB8 TB7 5.6K BN64 WHT RED SPEED 10K 4 BN67 PLATFORM LEVEL 5.1V SECONDARY BOOM UP/DOWN BN65 BN63 BN97 BOOM PRIMARY EXTEND BOOM UP/DOWN RETRACT 5 PLATFORM ROTATE (OPTION) JIB BOOM UP/DOWN BLK 30 3 86 87A 87 85 CR87 30 4 86 87A 87 85 PLAT ROTATE PLATFORM LEVEL 5.6K CR9 JIB UP/DOWN C71 6 30 5 86 87A 87 85 TB9 7 PLATFORM ROTATE RIGHT Y61 Y62 7 BLU 6 BLU/BLK PLATFORM ROTATE LEFT Y20 LIMIT SWITCH SHOWN IN UNLOADED POSITION Y60 5 JIB BOOM GRN EXTEND Y19 4 PLATFORM LEVEL UP LS19 3 GRN/BLK JIB BOOM RETRACT 2 ORG 1 ORG/BLK 3 PLATFORM LEVEL DOWN WHT 2 ORG BLK 1 RED 4 Y63 8 ES-TZ50F Part No. 84577 TZ-50 5 - 69 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ50005-211 to TZ5005-284) 5 - 69 5 - 70 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) 5 - 71 5 - 72 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5005-285 to TZ5010-144) A B C D E F G H I J K PLATFORM CONTROL BOX 1 PLATFORM E-STOP POWER P2 BN2 BN3 H1 FAULT ALARM START CHOKE G7 BCI PA-3 PA2 PA1 2 1 DRIVE CONTROLS DRIVE E-STOP POWER 2 BK/RD BK BK DRIVE CONTROL BOX CD10 WH CD11 DE WH/BK DA DF LS18A RD CD-9 RD/BK PA-3 PA2 PA1 2 1 BK/WH GN WH GN/YELLOW WH 3 LS18 GROUND CONTROL BOX TB3 CB2 15AMP. KS1 P1 RD RD RD TB3 TB2 PLAT TB4 GRD CB1 15AMP. H5 FAULT ALARM BN68 BN90 CHOKE START CR65A TB4A TB4A 4 CR64 (2) GROUND CONTROLS CR65A (4) L13 L12 5 CR8 (15) CR1 (16) CR15 (17) TB7 CR76 (3) U16B + LOAD L15 CR76 (3) CR75 (1) CR75 (1) - L14 GCON GROUND GRN/WHT CC9 CC8 RED BLU/WHT CC7 CC6 RED ORG/WHT CC5 CC4 RED RED/WHT CC3 BATTERY 24V RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED LS FAULT RELAY R3 BK LEVEL SENSOR RELAY R1 PA11 BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 B CC2 RED PA10 WH IND. STARTER RELAY R16 TZ-50 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH 5 - 72 BK S7 REGULATOR 7 ENGINE OPTION FB STA. M3 8 A U26 FB1 WH - WH BAT. + NO C BAT. C A RD EXCT. F9 50AMP. Q7 B5 ALTERNATOR RD D1 PR5 F PB11 275AMP. F9A 50AMP. RD PB12 RD/WH PB9 F6 BK WH BK RD RD PB10 BK/RD PB8 E B 6 OUTRIGGER LIMIT SWITCHES BATTERY GROUND ES0440C L M N September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5005-285 to TZ5010-144) N M L K J I H G F E D C B A PLATFORM CONTROL BOX PLATFORM CONTROL BOX PLATFORM E-STOP POWER BN61 1 BN62 DOWN ENABLE DOWN ENABLE TB3 TB4 PLATFORM GROUND TB2 R22B 5.6K KEY SIGNAL CR9 CR71 (4) CR87 R14 10K POT (3) (5) R22C C4B 5.6K PLATFORM GROUND 5.1V PA 7 PA8 PA6 GR/WH BL/WH 3 BL GN/BK RD/WH 8 7 6 5 4 2 1 DC DP OR/WH RD/WH WH RD BK BL/BK 0-5V WH/BK DB DN DM DL 2 TB3 HALL EFFECT WITH ELECTRONIC DAMPING GN/WH DH AUTOLEVEL MODULE FWD/REV SWITCH DGDJ OR WH BL DK BK GN/BK DD RD RD/WH DRIVE CONTROL BOX RIGHT PROPORTIONAL JOYSTICK POWER DRIVE E-STOP POWER LEFT PROPORTIONAL OR/BK UP ENABLE JOYSTICK GROUND DOWN ENABLE GROUND CONTROL BOX TB3 BN59 DOWN ENABLE BN60 UP ENABLE TB9 CR65A TB4A 4 TB10 BN60 BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB32 C4A CR28 (7) (5) CR86 Y36 Y33 Y34 S2 A1 M5 M5 MOTOR BATTERY GROUND 7 GCON GROUND (HARNESS GROUND PLUG) ES0440C 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y35 2 JIB RELAY R4 2 PLAT LEVEL RELAY R3 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 EXTENSION RELAY R14 3 U6 PLATFORM ROTATE RELAY R3 BK 1 B- 2 1 SECONDARY RELAY R12 GN/WH 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 CD8 BK 1 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER CD7 BL/WH 2 CR69 (14) CR68 (12) J CD6 BK 2 1 G6 HM CR67 (13) WH/BK CD5 OR/WH 2 CR70 (11) CR72 (10) (18) L1 BL CD4 1 TB32 TB12 CR86 (18) H CD3 BK 2 1 Y11 2 CD2 2 1 2 BK Y50 2 Y40 BK Y59 2 RD/WH GN/BK 2 1 2 Y50A CD1 L GN BL/BK WH WH OR OR/BK BK K 8 3 1 5 7 2 1 2 Y58 C4 CR77 (6) CR65B TB35 DRIVE OPTION 5 CR28 TB22 CR72 (10) BATTERY 24V TB14 CR65B C5 GCON GROUND R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL GROUND CONTROL BOX TB11 TB8 RR O/R ENABLE 8 TZ-50 5 - 73 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) 5 - 73 5 - 74 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5005-285 to TZ5010-144) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY BN64 SEC PLATFORM GROUND GN/WH BL/BK 1 6 7 PB7 BK BL GN GN/BK 5 GN 1 1 Y61 Y60 BK Y20 Y19 TB31 1 BL PLAT LEVEL ENABLE ROTATE ENABLE BL/BK BN58 BN57 TB11 1 BN93 PLAT ROTATE ENABLE GN JIB MANIFOLD 1 GN/BK OR OR/BK PB7 PB6 PB5 4 OR/BK PB4 PB6 PB5 BK/WH PB3 OR PB4 RD/BK PB2 3 PB3 BL/BK PB1 2 PB2 WH/BK OR/BK PB1 GROUND CONTROL BOX 3 4 1 Y63 Y62 TB30 TB33 5 TB34A CR78A (9) SEC ENABLE TB29 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD BN36 - GCON GROUND LIFT CUTOUT RELAY 2 BK BK/WH 2 1 Y26 1 Y52 W V RD RD/BK 2 1 Y22 1 Y23 U T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL 1 Y24 S BL/BK LR O/R R LS14 LF O/R WHT LS12 WHT/BK RR O/R P LS15 N WHT RF O/R CC10 WHT CC1 LS13 1 Y21 2 2 Y25 2 2 2 2 6 ES0440C 7 2 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 2 PLATFORM ROTATE CCW (8) TB27 2 PLATFORM ROTATE CW U16A BN56 TB26 2 JIB EXTEND TB28 CR61 BN54 2 JIB RETRACT BN55 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 PRI ENABLE 8 TZ-50 5 - 75 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5005-285 to TZ5010-144) 5 - 75 5 - 76 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) 5 - 77 5 - 78 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5010-145 to TZ5011-131) A B C D E F G H I J K PLATFORM CONTROL BOX 1 PLATFORM E-STOP POWER P2 BN2 BN3 BCI PLATFORM GROUND DRIVE CONTROL BOX WH P4-11 P4-10 DE WH/BK DA DF LS18A RD P4-9 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 RD/BK BK/RD LS18 BK/WH P1-2 BK DRIVE E-STOP POWER GN P1-1 BK DRIVE CONTROLS WH P10-3 GN/YELLOW P1-3 P10-2 WH 3 H1 FAULT ALARM CONTROLS TB9 P10-1 2 PLATFORM START CHOKE G7 GROUND CONTROL BOX TB3 CB2 15AMP. RD RD TB3 KS1 P1 RD TB2 PLAT TB4 BN90 CHOKE GRD CB1 15AMP. H5 FAULT ALARM BN68 START CR65A TB4A TB4A 4 CR64 (2) GROUND CONTROLS CR65A (4) L12 5 CR8 (15) U16B CR1 (16) CR15 (17) TB7 CR76 (3) + LOAD L14 L15 CR75 (1) CR75 (1) - L13 CR76 (3) GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 ORG/WHT P5-5 P5-4 RED RED/WHT P5-3 BATTERY 24V RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 2 LS FAULT RELAY R3 IND. P5-2 RED REGULATOR STARTER RELAY R16 TZ-50 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH ENGINE OPTION FB1 LEVEL SENSOR RELAY R1 S7 7 5 - 78 FB STA. M3 8 P1-11 BK U26 P1-10 WH - NO P3-A BK BAT. + WH BAT. 3 1 RD B5 EXCT. F9 50AMP. Q7 D1 ALTERNATOR P3-C WH PR5 P3-F RD P8-3 P2-11 RD P8-4 P8-1 P2-12 RD/WH P8-5 P2-9 F6 275AMP. F9A 50AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 OUTRIGGER LIMIT SWITCHES BATTERY GROUND ES0440D L M N September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5010-145 to TZ5011-131) N M L K J I H G F E D C B A PLATFORM CONTROL BOX PLATFORM CONTROL BOX PLATFORM E-STOP POWER BN61 1 BN62 DOWN ENABLE DOWN ENABLE TB3 TB4 PLATFORM GROUND TB2 AUTOLEVEL MODULE FWD/REV SWITCH CR9 CR71 (4) CR87 R14 10K POT (3) (5) R22C C4B 5.6K PLATFORM GROUND P1-7 P1-8 3 BL P9-8 GN/BK P1-6 RD/WH GR/WH BL/WH P9-7 P9-6 P9-5 P9-4 P9-2 P9-1 DC DP OR/WH RD/WH WH RD BK BL/BK DB DN DM DL 5.6K KEY SIGNAL 0-5V WH/BK DH R22B 5.1V DD DD 2 TB3 HALL EFFECT WITH ELECTRONIC DAMPING GN/WH OR BK WH BL DGDJ RD GN/BK RD/WH DK RIGHT PROPORTIONAL JOYSTICK POWER DRIVE E-STOP POWER UP ENABLE JOYSTICK GROUND DOWN ENABLE LEFT PROPORTIONAL OR/BK DRIVE CONTROL BOX GROUND CONTROL BOX TB3 BN59 DOWN ENABLE BN60 UP ENABLE TB9 CR65A TB4A 4 TB10 BN60 BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE RR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB32 C4A CR28 (7) (5) CR86 Y33 Y34 2 S2 A1 M5 M5 MOTOR BATTERY GROUND 7 GCON GROUND (HARNESS GROUND PLUG) ES0440D 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y36 PLATFORM ROTATE RELAY R3 2 Y35 JIB RELAY R4 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 PLAT LEVEL RELAY R3 3 U6 EXTENSION RELAY R14 1 B- 2 1 SECONDARY RELAY R12 BK 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 GN/WH 1 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER P4-8 BK 2 CR69 (14) CR68 (12) P3-J P4-7 BL/WH 2 2 1 G6 HM CR67 (13) WH/BK P4-6 BK 2 CR70 (11) CR72 (10) (18) L1 BL P4-5 OR/WH 1 TB32 TB12 CR86 (18) P3-H P4-4 2 1 Y11 2 1 BK 2 1 Y40 BK 2 P4-3 2 Y50 BK 2 Y59 P4-2 Y58 RD/WH DRIVE OPTION P4-1 GN BK BL/BK WH WH OR OR/BK BK P3-L GN/BK P3-K P3-M P7-8 P7-3 P7-1 P7-5 P7-7 P7-2 1 2 Y50A C4 CR77 (6) CR65B TB35 2 5 CR28 TB22 CR72 (10) BATTERY 24V TB14 CR65B C5 GCON GROUND R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL GROUND CONTROL BOX TB11 TB8 8 TZ-50 5 - 79 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) 5 - 79 5 - 80 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5010-145 to TZ5011-131) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY BN64 SEC PLATFORM GROUND P6-1 BK GN/WH BL/BK BL P6-6 P6-7 P2-7 GN/BK P6-5 GN GN P6-4 1 1 Y61 Y60 BK Y20 Y19 TB31 1 BL PLAT LEVEL ENABLE ROTATE ENABLE BL/BK BN58 BN57 TB11 1 BN93 PLAT ROTATE ENABLE GN JIB MANIFOLD 1 GN/BK OR OR/BK P2-7 P2-6 P2-5 P2-6 OR/BK P2-4 OR BK/WH P2-3 P6-3 P2-4 RD/BK P2-2 OR/BK P2-3 BL/BK P2-1 P6-2 P2-2 WH/BK P2-5 P2-1 GROUND CONTROL BOX 3 1 Y63 Y62 TB30 TB33 5 TB34A CR78A (9) SEC ENABLE TB29 - GCON GROUND 1 Y21 2 2 Y25 2 2 2 LIFT CUTOUT RELAY R9 2 BK BK/WH 2 1 Y26 1 Y52 P3-W P3-V RD RD/BK 2 1 Y22 1 Y23 P3-U P3-T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL 1 Y24 P3-S BL/BK LR O/R P3-R LS14 LF O/R WHT LS12 WHT/BK RR O/R P3-P LS15 P3-N WHT RF O/R P5-10 WHT P5-1 LS13 ES0440D 2 2 6 7 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 2 PLATFORM ROTATE CCW TB27 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD TB26 BN36 2 PLATFORM ROTATE CW U16A (8) BN56 2 JIB EXTEND TB28 CR61 BN54 2 JIB RETRACT BN55 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 PRI ENABLE 4 8 TZ-50 5 - 81 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5010-145 to TZ5011-131) 5 - 81 5 - 82 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5011-132 to TZ5011-310) 5 - 83 5 - 84 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5011-132 to TZ5011-310) A B C D E F G H I J K L PLATFORM CONTROL BOX 1 PLATFORM E-STOP POWER P2 BN2 BN3 PLATFORM START CHOKE H1 FAULT ALARM CONTROLS TB9 P1-3 P1-2 P1-1 ENGINE OPTION DRIVE CONTROLS DRIVE E-STOP POWER HORN OPTION BK/RD BK BK LS18 DRIVE CONTROL BOX P4-10 WH P4-11 DE WH/BK DA DF LS18A RD P4-9 RD/BK P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 BK/WH GN WH GN/YELLOW WH 3 P10-3 P10-2 P10-1 2 PLATFORM GROUND GROUND CONTROL BOX TB3 CB2 15AMP. RD RD RD TB2 PLAT TB4 BN90 CHOKE GRD CB1 15AMP. 4 TB3 KS1 P1 H5 FAULT ALARM BN68 START CR65A TB4A TB4A CR64 (2) GROUND CONTROLS CR65A BCI G7 (4) L12 5 CR8 (15) CR1 (16) CR15 (17) TB7 CR76 (3) U16B + LOAD L14 L15 CR75 (1) CR75 (1) - L13 CR76 (3) GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 ORG/WHT P5-5 P5-4 RED RED/WHT P5-3 RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 2 BATTERY 24V LS FAULT RELAY R3 IND. P5-2 RED REGULATOR STARTER RELAY R16 TZ-50 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH ENGINE OPTION FB1 OUTRIGGER LIMIT SWITCHES LEVEL SENSOR RELAY R1 S7 7 5 - 84 FB STA. M3 8 P1-11 BK U26 P1-10 WH - NO WH BAT. + 3 1 RD EXCT. BAT. P3-A BK D1 ALTERNATOR P3-C WH B5 ODR1 F9 50AMP. Q7 P3-F RD P8-3 PR5 P2-11 RD P8-4 P8-1 P2-12 RD/WH P8-5 P2-9 F6 275AMP. F9A 50AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 CR20 ES0440E BATTERY GROUND M N September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5011-132 to TZ5011-310) N M L K J I H G F E D C B PLATFORM CONTROL BOX A PLATFORM CONTROL BOX PLATFORM E-STOP POWER BN61 1 BN62 DOWN ENABLE DOWN ENABLE TB3 TB4 PLATFORM GROUND TB2 AUTOLEVEL MODULE FWD/REV SWITCH (3) (5) R22C C4B 5.6K PLATFORM GROUND P1-7 P1-8 3 BL P9-8 P9-7 GN/BK P1-6 RD/WH GR/WH BL/WH P9-6 P9-5 P9-4 P9-2 P9-1 DC DP OR/WH RD/WH WH RD BK DB DN DM DL CR9 CR71 (4) CR87 R14 10K POT BL/BK DH 5.6K KEY SIGNAL GN/WH OR DD R22B 5.1V DD GROUND CONTROL BOX 2 TB3 HALL EFFECT WITH ELECTRONIC DAMPING 0-5V WH/BK RIGHT PROPORTIONAL DGDJ BK WH BL DK RD GN/BK RD/WH DRIVE CONTROL BOX JOYSTICK POWER DRIVE E-STOP POWER LEFT PROPORTIONAL OR/BK UP ENABLE JOYSTICK GROUND DOWN ENABLE TB3 BN59 DOWN ENABLE BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE TB11 TB8 RR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB14 CR65B TB32 C4A CR28 (7) (5) CR86 Y36 Y33 Y34 S2 A1 M5 M5 MOTOR 7 GCON GROUND (HARNESS GROUND PLUG) ES0440E 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y35 2 JIB RELAY R4 2 PLAT LEVEL RELAY R3 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 EXTENSION RELAY R14 3 U6 PLATFORM ROTATE RELAY R3 BK 1 B- 2 1 SECONDARY RELAY R12 GN/WH 1 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 P4-8 BK 2 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER P4-7 BL/WH 1 CR69 (14) CR68 (12) P3-J P4-6 BK 2 G6 HM CR67 (13) WH/BK P4-5 OR/WH 2 L1 BL P4-4 1 CR70 (11) CR72 (10) (18) P3-H P4-3 BK 2 1 Y11 2 P4-2 2 1 2 BK Y50 2 1 Y40 BK Y59 2 RD/WH 2 P4-1 GN BK BL/BK WH WH OR OR/BK BK P3-L GN/BK P3-K P3-M P7-8 P7-3 P7-1 P7-5 P7-7 P7-2 1 2 Y50A TB32 TB12 CR86 (18) TB35 2 C4 CR77 (6) CR65B CR72 (10) 5 CR28 TB22 C5 Y58 GROUND CONTROL BOX R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL BATTERY GROUND 4 TB10 BN60 BATTERY 24V UP ENABLE TB9 CR65A TB4A GCON GROUND BN60 8 TZ-50 5 - 85 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5011-132 to TZ5011-310) 5 - 85 5 - 86 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5011-132 to TZ5011-310) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY BN64 SEC PLATFORM GROUND P6-1 BK BL GN/WH BL/BK P6-7 P6-6 GN/BK GN P2-7 P6-5 GN BK 1 Y20 Y19 TB31 BL TB11 BL/BK PLAT LEVEL ENABLE ROTATE ENABLE 1 BN93 PLAT ROTATE ENABLE BN58 GN 4 JIB MANIFOLD 1 BN57 GN/BK OR OR/BK P2-7 P2-6 P2-5 P6-4 OR/BK P2-4 P2-6 P2-5 BK/WH P2-3 OR P2-4 RD/BK P2-2 P6-3 P2-3 BL/BK P2-1 P6-2 P2-2 WH/BK OR/BK P2-1 GROUND CONTROL BOX 3 1 1 Y61 Y60 1 Y63 Y62 TB30 TB33 5 TB34A CR78A (9) SEC ENABLE 1 Y21 2 2 Y25 2 2 2 LIFT CUTOUT RELAY R9 2 BK BK/WH 2 1 Y26 1 Y52 P3-W P3-V RD RD/BK 2 1 Y22 1 Y23 P3-U P3-T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL BL/BK 1 Y24 P3-S P3-R LR O/R WHT LS14 LF O/R WHT/BK LS12 P3-P RR O/R P3-N LS15 P5-10 WHT WHT RF O/R ES0440E 2 2 2 PLATFORM ROTATE CCW - P5-1 LS13 TB29 2 2 PLATFORM ROTATE CW GCON GROUND TB27 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD TB26 2 BN36 JIB EXTEND U16A (8) BN56 JIB RETRACT TB28 CR61 BN54 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 BN55 PRI ENABLE 6 7 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 8 TZ-50 5 - 87 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5011-132 to TZ5011-310) 5 - 87 5 - 88 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA (from serial number TZ5011-311) 5 - 89 5 - 90 Section 5 • Schematics September 2014 Electrical Schematic - ANSI/CSA, 1 of 3 (from serial number TZ5011-311) A B C D E F G H I J K L M PLATFORM CONTROL BOX 1 PLATFORM E-STOP POWER P2 BN3 BN2 CHOKE START PLATFORM CONTROLS H1 FAULT ALARM TB9 PLATFORM GROUND P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 2 ENGINE OPTION DRIVE CONTROLS DRIVE E-STOP POWER HORN OPTION BK/RD BK BK DRIVE CONTROL BOX WH P4-11 P4-10 DE WH/BK DA DF LS18A RD P4-9 P1-3 RD/BK GN WH P1-2 P1-1 P10-3 P10-2 P10-1 BK/WH GN/YELLOW WH 3 LS18 GROUND CONTROL BOX TB3 CB2 15AMP. P1 RD RD RD KS1 PLAT TB3 TB2 TB4 GRD BN68 START BN90 CHOKE CB1 15AMP. 4 H5 FAULT ALARM CR65A TB4A TB4A CR64 GROUND (2) CONTROLS CR65A (4) BCI G7 200 OHM 10W 5 L13 L12 L14 L15 TB7 (15) U16B CR1 CR15 CR8 (16) (17) CR76 (3) + CR76 CR75 CR75 LOAD - (3) (1) (1) GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 RED ORG/WHT P5-5 P5-4 RED RED/WHT P5-3 P5-2 BATTERY 24V U6-B+ RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 TILT ALARM LEVEL SENSOR OFF DELAY RELAY ODR1 2 TO 3 SECONDS ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 2 LS FAULT RELAY R3 IND. OUTRIGGER LIMIT SWITCHES LEVEL SENSOR RELAY R1 REGULATOR STARTER RELAY R16 STARTER MOTOR TZ-50 CHOKE RELAY R17 5 - 90 CHOKE RELAY ENGINE OPTION IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH 8 FB1 S7 P3-X FB STA. M3 QD1 BK - P1-11 BAT. + P1-10 WH BAT. WHT EXCT. NO U26 3 1 ALTERNATOR P3-A BK D1 P3-C WH CHARGER CR20 ODR1 RD 7 PR5 50 AMP. F9 P3-F RD Q7 B5 P2-11 P8-3 RD P8-4 P8-1 P2-12 RD/WHT P8-5 F9A 50AMP. QD1 P2-9 F6 275AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 BATTERY GROUND ES0440G N September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 2 of 3 (from serial number TZ5011-311) N M L K J I H G F E D C B PLATFORM CONTROL BOX A PLATFORM CONTROL BOX PLATFORM E-STOP POWER BN61 1 BN62 DOWN ENABLE UP ENABLE TB3 TB4 PLATFORM GROUND TB2 FWD/REV SWITCH RIGHT PROPORTIONAL TB3 AUTOLEVEL MODULE HALL EFFECT WITH ELECTRONIC DAMPING 5.1V CR71 (3) CR9 (4) CR87 (5) PLATFORM GROUND P1-7 P1-8 3 BL GN/BK P9-8 P9-7 P9-6 P9-5 P1-6 RD/WH GR/WH BL/WH OR/WH RD/WH P9-1 DB DN DM DL DC DP 2 R22B 5.6K R14 10K POT R22C 5.6K C4B WH RD P9-4 BK P9-2 GN/WH OR KEY SIGNAL BL/BK 0-5V WH/BK LEFT PROPORTIONAL OR/BK BK DG DJ DH JOYSTICK GROUND DK RD DD WH BL GN/BK GROUND CONTROL BOX RD/WH DRIVE CONTROL BOX UP ENABLE JOYSTICK POWER DRIVE E-STOP POWER DOWN ENABLE GROUND CONTROL BOX TB3 BN59 BN60 DOWN ENABLE TB9 CR65A TB4A BN53 BN52 BN60 UP ENABLE TB20 RR O/R ENABLE LR O/R ENABLE TB24 (4) (8) CR28 (7) (10) C4A CR86 CR86 (18) (18) CR70 (11) CR72 (10) CR68 (12) CR67 (13) GCON GROUND HOUR METER JIB RELAY R4 7 GCON GROUND (HARNESS GROUND PLUG) ES0440G 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 PLATFORM ROTATE RELAY R3 M5 MOTOR PLAT LEVEL RELAY R3 M5 PRIMARY RELAY R13 D1 EXTENSION RELAY R14 A1 ROTATE RELAY R11 1 U6 3 BM B+ MOTOR CONTROLLER SECONDARY RELAY R12 Y34 2 HM G6 CR69 (14) 6 OUTRIGGER RELAY R10 12 1 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER Y33 TB12 CR77 (6) P3-J WH/BK Y36 BK 12 1 GN/WH BK Y35 BL/WH 1 2 C4 CR65B (5) TB32 47 mH, 2.5 AMP, 0.034 OHM UB-6+ BATTERY GROUND C5 P3-H BL P4-8 P4-7 P4-6 BK OR/WH BK 2 P4-5 P4-4 P4-3 P4-2 Y39 2 BK 2 BK 2 12 1 Y50 Y11 2 RD/WH Y40 1 Y59 P4-1 P3-LGN/BK GN P3-K BK 1 2 P3-M P7-8 BL/BK P7-3 WH OR BK P7-1 WH P7-5 P7-2 P7-7 OR/BK Y58 TB32 L1 1 1 1 5 CR28 CR72 Y50A R22 1K OHM (5) TB22 1 TB16 CR65B TB15 CR61 TB35 4 TB14 TB17 TB18 TB11 TB13 CR65A AUTOLEVEL ENABLE BATTERY 24V (6) TB5 TB23 TB21 TB10 TB11 TB8 CR77 BN51 BN50 RF O/R ENABLE LF O/R ENABLE BN49 GCON GROUND UP ENABLE 8 TZ-50 5 - 91 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5011-311) 5 - 91 5 - 92 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA, 3 of 3 (from serial number TZ5011-311) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN67 PLAT LEVEL ENABLE BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE CR78B (1) CR78B BN64 SEC ENABLE BN65 EXT ENABLE BN97 JIB ENABLE CR71 CR9 (3) CR87 (4) (5) PLATFORM GROUND P6-5 P2-7 P6-6 P6-7 P6-1 GN GN/WH BL/BK BL BK GN OR GN/BK OR/BK P6-4 P6-3 1 Y20 TB31 TB33 TB34A CR78A (9) TB32 PRI ENABLE EXT ENABLE JIB ENABLE BN55 BN54 BN56 BN36 TB26 Y19 CR78A TB27 LOAD - GCON GROUND LIFT CUTOUT RELAY R9 BK BK/WH P3-W P3-V RD RD/BK P3-U P3-T BL BL/BK P3-S P3-R LS14 WHT LF O/R WHT/BK LS12 RR O/R P3-P RF O/R P3-N LS15 WHT WHT P5-10 P5-1 LS13 LR O/R 1 OUTRIGGER LIMIT SWITCHES Y24 Y53 Y23 2 Y22 Y52 2 2 Y26 Y25 Y21 2 2 2 2 ES0440G 2 PLATFORM ROTATE CW (14) (13) 5 2 PLATFORM ROTATE CCW CR69 CR67 (12) 2 JIB EXTEND CR68 (11) Y62 2 JIB RETRACT CR70 + 2 PLAT LEVEL EXTEND JIB MANIFOLD PLAT LEVEL RETRACT U16A Y63 Y61 Y60 2 TB29 (8) 1 (9) TB28 CR61 4 1 TB30 SEC ENABLE TB25 BK 1 BL 1 BL/BK 1 GN ROTATE ENABLE GN/BK PLAT LEVEL ENABLE OR BN93 BN93 PLAT ROTATE ENABLE BN58 TB11 3 OR/BK BN58 BN57 2 P2-7 P2-6 BN57 P2-6 P6-2 P2-4 P2-1 P2-5 BK/WH P2-3 OR/BK P2-4 RD/BK P2-2 P2-5 P2-3 BL/BK WH/BK P2-2 P2-1 GROUND CONTROL BOX LIFT CUTOUT RELAY (1) BN63 PRI ENABLE 6 7 2 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 8 TZ-50 5 - 93 September 2014 Section 5 • Schematics Electrical Schematic - ANSI/CSA (from serial number TZ5011-311) 5 - 93 5 - 94 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (to serial number TZ5004-181) 5 - 95 5 - 96 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (to serial number TZ5004-181) A B C D E F G H I J K L TO A TO B N (PLATFORM CONTROLS) (PLATFORM CONTROLS) 1 M (DRIVE CONTROLS) (DRIVE CONTROLS) - NOTE MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF 2 TO N.C.H.O. N.O.H.C. N.C.H.O. FB DK OR/RD DJ BL DH GN/BK DG GN/BK DF RD DE CD11 WH BL BOOM DOWN CD9 BK/WH WH LS18A RD/BK PA6 CD10 WH/BK DD N.O.H.C. RD RD/WH DC PA5 RD/WH PA4 PA3 WH/BK WH/RD DB PA2 OR WH PA1 BK PA11 BK/RD PA10 BK 3 BK WH GN BK WH GN DA MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF BOOM DOWN FLASHING BEACON (OPTION) 2 - NOTE - LS18 FB1 1 C (AUTO-LEVEL) PA7 PA8 PA9 TB1 3 TB4 TB2 TB3 BN59 4 BN68 BN90 ENGINE START CHOKE GROUND PLATFORM MODELS WITH ENGINE (OPTION) KS1 KEY SWITCH BN60 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) H5 L4 ALARM LED TB8 TB9 30 6 86 87A 87 85 TB10 TB11 TB5 CR64 30 86 2 FAULT GROUND 87 85 TB13 CR77 TB6 30 87A 4 R22 DOWN ENABLE 86 87A 5 87 CR65A 87A CB1 15 AMP 30 85 87A 16 87 86 30 85 87A 17 87 86 CR8 CR1 CR15 IGNITION ENGINE START STARTING AID CB2 U16B 85 30 1 86 87A 87 85 87A TIME DELAY (10 TO 30 SECONDS) + - LOAD TB35 3 86 30 5 86 87 85 87A 87 85 CR75 CR76 LEVEL SENSOR LIMIT SWITCH FAULT TB17 L12 L13 L14 L15 LF LED RF LED LR LED RR LED CR65B C5 4700uF 30 POWER SUPPLY 18 87A 87 86 30 7 86 85 87A 87 85 CR86 SEQUENCING U6 CUTOUT C4A C4 ZENER DIODE 3.3V DC ZENER DIODE 5.1V DC TB22 U16A TIME DELAY (0.1 TO 10 SECONDS) TB20 TB23 TB21 TB24 TB28 + - LOAD 6 87 86 RIGHT REAR OUTRIGGER CR28 TB15 15 BN51 LEFT REAR OUTRIGGER TB18 P1 30 BN50 RIGHT FRONT OUTRIGGER TB32 U6 CUTOUT 30 BN53 LEFT FRONT OUTRIGGER AUTO LEVEL TB16 85 BN52 BN49 1000 OHM TB14 TB7 EMERGENCY STOP GROUND CONTROL BOX FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB12 GROUND CONTROL BOX TB35 GN/WH 15 AMP F + U9 BATTERY CHARGER + + (AUTO-LEVEL) 1 OUTRIGGERS SHOWN IN STOWED POSITION 0-5V DC KEY U6 MOTOR CONTROLLER ES-TZ50A TZ-50 CC3 CC4 CD3 CD4 CC5 CC6 CD5 CD6 CC7 CC8 CD7 CD8 Y35 Y36 Y33 Y34 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER N.C.H.O. N.C.H.O. T2 + 5 - 96 CD2 GN/WH B- CD1 BL/WH B+ B CC1 CC2 S2 A1 AC INPUT - 8 OR/WH M3 STARTER MOTOR 7 GN/WH M3 6 OR/WH + U26 IGNITION 5 BL/WH S7 LEVEL SENSOR 3 - 3 WH/BK MOTOR M5 F9 50 AMP POWER RELAY 4 RD/WH 275A FUSE PR5 50 AMP 2 WH G M5 F6 N.O. BK - F9A 1 RD CHOKE SOLENOID H BK Q7 J A RD/WH C RD - 8 C WH 4-6V BATTERY RD/WH D1 ALTERNATOR B5 A PB12 BL PB11 WH/BK PB10 RD BK PB9 BK/RD RD PB8 BK D WH E RD 7 B Part No. 84577 N.C.H.O. N.C.H.O. LS12 LS13 LS14 LS15 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER CC9 CC10 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (to serial number TZ5004-181) N M L K J I H G A F E D C B A TO A (PLATFORM CONTROLS) (PLATFORM CONTROLS) (DRIVE CONTROLS) (DRIVE CONTROLS) B TO C 1 B (AUTO-LEVEL) 2 - NOTE - FUNCTION ENABLE LIFT CUT-OUT RD/WH TB30 CR78A OR/WH TB33 CR73 BL/WH 85 GN/WH 87 WH 87A BK PLATFORM ROTATE (OPTION) DM WH/BK PLATFORM LEVEL UP/DOWN DL RD BN93 86 PB6 OR/BK BN58 9 OR PB7 30 TURNTABLE ROTATE TB31 PB4 GN/WH 85 PB5 GN 87 BN57 PB3 GN/WH 86 PB2 BK/WH 87A 8 PB1 OR/BK 30 RD/BK DP BL/BK BL/BK WH/BK MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF DN 2 3 1 4 8 7 6 5 S10 S9 LEFT/RIGHT AXIS LEVEL SENSOR FRONT/REAR AXIS LEVEL SENSOR 4 2 3 1 4 GROUND CONTROL BOX TB34A BN55 BN54 BN56 BN36 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/RETRACT JIB BOOM UP/DOWN TB25 TB26 3 1 3 4 CR66 LEVEL SENSOR RELAY YL CR61 86 30 AUTO LEVEL SYSTEM RELAY 87A TB29 TB27 2 AUTO LEVEL 87 85 TB32 86 30 RD 5 RD TB28 30 10 30 85 87A 11 86 30 85 87A 12 86 30 85 87A 13 86 30 85 87A 14 86 GN YL 86 30 86 30 86 30 87A 87 85 86 30 + 86 GN 87A 87 87 87 87 87 85 87A G6 CR72 CR70 CR68 CR67 CR69 HOUR METER OUTRIGGER TURNTABLE ROTATE SECONDARY BOOM PRIMARY BOOM BOOM EXTEND 87 85 87A 87 85 87A 87 85 87A 87 85 6 TB35 TB34 N R P S T OUTRIGGER EXTEND ROTATE LEFT SECONDARY DOWN PRIMARY DOWN BOOM RETRACT Y39 Y24 Y53 Y22 Y26 OUTRIGGER RETRACT ROTATE RIGHT SECONDARY UP PRIMARY UP BOOM EXTEND 8 7 Y50 Y58 DRIVE FWD/REV LEFT PROPORTIONAL DRIVE RIGHT Y50A Y59 DRIVE FWD/REV RIGHT PROPORTIONAL DRIVE LEFT BL Y25 5 3 OR/BK Y21 1 OR Y52 2 WH Y23 BK BK/WH RD RD/BK BL BL/BK WH/BK WH GN/BK GN Y40 ES-TZ50A W V U WH M L BK K Y11 7 BRAKE RELEASE (DRIVE) 8 BRN Part No. 84577 TZ-50 5 - 97 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (to serial number TZ5004-181) 5 - 97 5 - 98 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (to serial number TZ5004-181) N M L K J I H G F E D C B A A 1 B 2 P3 P2 EMERGENCY STOP EMERGENCY STOP 2 3 4 5 6 7 G7 F BATTERY CHARGE INDICATOR E PA6 PA8 PA7 PB1 PB5 PB7 PB4 PB3 PB2 DRIVE CONTROL BOX 1 JOYSTICK CONTROLLER PLATFORM CONTROL BOX PB6 3 CR74 H1 FUNCTION ENABLE ALARM JC5 GN PA3 BL/BK PA9 RD/BK PA4 BK/WH WH PA5 GN/WH OR/RD PA1 OR/BK OR PA2 WH/BK WH/RD 3 BL BK 2 GN/BK BK/RD 1 RD/WH BK DD GN DK WH DG RD/WH DJ GN/BK DH BL DP WH DB RD DL BL/BK DC BK DM GN/WH DN WH/BK DE OR OR/BK DA RD/BK GN BK/WH DF L4A LED BN2 ENGINE START BN3 CHOKE BN61 BN62 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) FUNCTION ENABLE (BOOM UP, BOOM EXTEND TURNTABLE AND PLATFORM ROTATE RIGHT) 30 1 86 87A 87 85 4 PLATFORM ROTATE (OPTION) BN66 R22B MODELS WITH ENGINE (OPTION) TURNTABLE ROTATE 5.6K OHM PLATFORM ROTATE LIFT CUT-OUT RD 30 2 86 87A 87 85 5 WH R14 BK RESISTOR 0-10K OHM BN98 CR78B C4B BN97 BN64 BN63 BN65 JIB BOOM UP/DOWN SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/ RETRACT ZENER DIODE 5.1V DC 6 CR9 30 4 86 87 85 30 5 86 87A 4 1 2 3 1 4 87 85 3 86 87A 87 85 Y62 Y19 JIB BOOM RETRACT PLATFORM ROTATE LEFT PLATFORM LEVEL DOWN PLATFORM LEVEL 3 OR/BK Y60 CR71 OR N.O. (SWITCH SHOWN IN UNLOADED POSITION) 30 2 GN N.C. 7 GN/BK GN/BK LOAD SENSE 6 5 GN LS19 87A CR87 PLATFORM ROTATE JIB BOOM UP/DOWN Y61 Y63 Y20 JIB BOOM EXTEND PLATFORM ROTATE RIGHT PLATFORM LEVEL UP 7 ES-TZ50A Part No. 84577 TZ-50 8 5 - 99 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (to serial number TZ5004-181) 5 - 99 5 - 100 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5004-182 to TZ5005-210) 5 - 101 5 - 102 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5004-182 to TZ5005-210) A B C D E F G H I J K L M TO 1 N A (PLATFORM CONTROLS) TO B (DRIVE CONTROLS) - NOTE MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF 2 TO N.C.H.O. N.O.H.C. N.C.H.O. FB DK OR/RD DJ GN/BK DH BL DG GN/BK DF RD DE CD11 WH BL BOOM DOWN CD9 BK/WH WH LS18A RD/BK PA6 CD10 WH/BK DD N.O.H.C. RD RD/WH DC PA5 RD/WH PA4 PA3 WH/BK DB PA2 WH/RD OR WH PA1 BK PA11 BK/RD PA10 BK 3 BK WH GN BK WH GN DA MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF BOOM DOWN FLASHING BEACON (OPTION) 2 - NOTE - LS18 FB1 1 C (AUTO-LEVEL) PA7 PA8 PA9 TB1 TB4A 3 TB2 TB4 6A 6A TB3 BN59 GROUND CONTROL BOX 4 BN68 BN90 ENGINE START CHOKE GROUND PLATFORM KEY SWITCH H5 L4 ALARM LED GROUND CONTROL BOX FUNCTION ENABLE (BOOM UP, EXTEND, ROTATE RIGHT AND OUTRIGGER RETRACT) TB8 TB10 TB9 30 6 86 87A 87 85 CR64 MODELS WITH ENGINE (OPTION) KS1 BN60 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, ROTATE LEFT AND OUTRIGGER EXTEND) 6A 6A TB11 FAULT GROUND 30 86 2 87A 87 TB13 CR77 TB5 30 4 86 87A 87 85 85 DOWN ENABLE R22 BN49 1000 OHM AUTO LEVEL TB14 TB7 5 TB17 TB16 BN52 BN53 BN50 BN51 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER L12 L13 L14 L15 LF LED RF LED LR LED RR LED TB18 TB32 CR65A U6 CUTOUT EMERGENCY STOP 30 87A 87 86 30 85 87A 16 87 86 30 85 87A 17 87 86 85 U16B TIME DELAY CB1 15 AMP CR8 CR1 CR15 IGNITION ENGINE START STARTING AID CB2 30 1 86 30 3 86 30 5 86 87A 87 85 87A 87 85 87A 87 85 + C5 4700uF 30 18 86 30 7 86 85 87A 87 85 TB22 U16A TIME DELAY TB20 (0.1 TO 10 SECONDS) (10 TO 30 SECONDS) - POWER SUPPLY LOAD TB35 CR75 CR76 LEVEL SENSOR LIMIT SWITCH FAULT 87A 87 CR86 CR65B SEQUENCING U6 CUTOUT C4A C4 ZENER DIODE 3.3V DC ZENER DIODE 5.1V DC TB23 TB21 TB24 TB28 + - LOAD 6 15 LEVEL SENSOR RELAY P1 TB12 CR28 TB15 TB35 GN/WH 15 AMP F + + + AC INPUT B- U9 - BATTERY CHARGER TZ-50 CC3 CC4 CD3 CD4 CC5 CC6 CD5 CD6 CC7 CC8 CD7 CD8 (AUTO-LEVEL) Y35 Y36 Y33 Y34 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER N.C.H.O. N.C.H.O. T2 3 OUTRIGGERS SHOWN IN STOWED POSITION KEY 0-5V DC U6 MOTOR CONTROLLER + 5 - 102 CD2 GN/WH B+ CD1 A1 S2 B CC1 CC2 BL/WH M3 STARTER MOTOR 8 OR/WH M3 7 GN/WH + U26 IGNITION 6 OR/WH S7 LEVEL SENSOR 1 - 5 BL/WH MOTOR M5 F9 50 AMP POWER RELAY 3 WH/BK 275A FUSE PR5 50 AMP 4 RD/WH G 2 WH F9A M5 F6 N.O. BK - 1 RD CHOKE SOLENOID J BK Q7 H A RD/WH C WH/BK - 8 C BL 4-6V BATTERY A RD D1 ALTERNATOR B5 PB12 WH PB11 RD/WH PB10 RD PB9 BK/RD PB8 BK BK RD D WH E RD 7 B Part No. 84577 ES-TZ50D N.C.H.O. N.C.H.O. LS12 LS13 LS14 LS15 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER CC9 CC10 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5004-182 to TZ5005-210) N M L K J I H G F E D C B A A TO A (PLATFORM CONTROLS) B TO 1 B (DRIVE CONTROLS) C 2 - NOTE - OR/WH RD/WH 85 BL/WH 87 GN/WH 87A WH TB31 BK 86 DM WH/BK 9 DL RD 30 PB6 OR/BK PB7 BN58 BN57 TURNTABLE ROTATE OR PB4 GN/WH PB5 GN PA12 GN/WH PB3 BK/WH PB2 OR/BK PB1 RD RD/BK DP BL/BK WH/BK BL/BK MACHINE SHOWN IN STOWED POSITION WITH THE POWER OFF DN 2 3 1 4 8 7 6 5 S10 S9 LEFT/RIGHT AXIS LEVEL SENSOR FRONT/REAR AXIS LEVEL SENSOR AUTO LEVEL 3 BN93 PLATFORM LEVEL UP/DOWN PLATFORM ROTATE (OPTION) TB33 4 TB30 2 3 1 4 GROUND CONTROL BOX CR78A LIFT CUT-OUT TB34A BN55 BN54 BN56 BN36 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/RETRACT JIB BOOM UP/DOWN TB25 TB26 3 1 4 CR66 LEVEL SENSOR RELAY YL CR61 86 30 AUTO LEVEL SYSTEM RELAY 87A TB29 TB27 2 87 85 TB32 5 86 30 RD RD TB28 30 10 30 85 87A 11 86 30 85 87A 12 86 30 85 87A 13 86 30 85 87A 14 86 GN YL 86 30 86 30 86 30 87A 87 85 86 30 + 86 GN 87A 87 87 87 87 87 85 G6 CR72 CR70 CR68 CR67 CR69 HOUR METER OUTRIGGER TURNTABLE ROTATE SECONDARY BOOM PRIMARY BOOM BOOM EXTEND 87A 87 85 87A 87 85 87A 87 85 87A 87 85 6 TB35 TB34 N R P S T OUTRIGGER EXTEND ROTATE LEFT SECONDARY DOWN PRIMARY DOWN BOOM RETRACT Y39 Y24 Y53 Y22 Y26 OUTRIGGER RETRACT ROTATE RIGHT SECONDARY UP PRIMARY UP BOOM EXTEND 8 7 Y50 Y58 DRIVE FWD/REV LEFT PROPORTIONAL DRIVE RIGHT Y50A Y59 DRIVE FWD/REV RIGHT PROPORTIONAL DRIVE LEFT BL Y25 5 3 OR/BK Y21 1 OR Y52 2 WH Y23 BK BK/WH RD/BK RD BL/BK BL WH WH/BK GN GN/BK Y40 ES-TZ50D W V U WH M L BK K Y11 7 BRAKE RELEASE (DRIVE) 8 BRN Part No. 84577 TZ-50 5 - 103 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5004-182 to TZ5005-210) 5 - 103 5 - 104 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5004-182 to TZ5005-210) N M L K J I H G F E D C B A A 1 B 2 EMERGENCY STOP 3 4 5 6 7 JC5 1 JOYSTICK CONTROLLER PLATFORM CONTROL BOX PA8 PA7 PB1 PA12 PB5 PB7 PB4 PB3 PB2 GN P2 EMERGENCY STOP PA6 BL/BK PA3 RD/BK PA9 BK/WH PA4 GN/WH WH PA5 OR/BK OR/RD PA1 RD OR PA2 WH/BK WH/RD 3 BL BK 2 GN/BK BK/RD 1 RD/WH BK DD GN DK WH DG RD/WH DJ GN/BK DH BL DL WH DB RD DP GN/WH BK DC P3 2 DRIVE CONTROL BOX DM BL/BK DN WH/BK DE OR OR/BK DA RD/BK GN BK/WH DF PB6 3 G7 F H1 BATTERY CHARGE INDICATOR E ALARM TB1 L4A LED BN2 ENGINE START BN3 CHOKE BN61 BN62 FUNCTION ENABLE (BOOM DOWN, BOOM RETRACT, TURNTABLE AND PLATFORM ROTATE LEFT) FUNCTION ENABLE (BOOM UP, BOOM EXTEND TURNTABLE AND PLATFORM ROTATE RIGHT) TB4 TB3 6A TB2 BN66 R22B MODELS WITH ENGINE (OPTION) TURNTABLE ROTATE 5.6K OHM BN98 PLATFORM LEVEL PLATFORM ROTATE RD 87A 2 86 87 85 TB6 TB8 5 TB7 BK R22C C4B BN67 LIFT CUT-OUT WH R14 RESISTOR 0-10K OHM CR78B 30 TB5 4 PLATFORM ROTATE (OPTION) 6A 5.6K OHM BN97 BN97 BN64 BN63 BN65 JIB BOOM UP/DOWN JIB BOOM UP/DOWN SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN BOOM EXTEND/ RETRACT ZENER DIODE 5.1V DC 6 CR9 30 4 86 87 85 30 5 86 87A 87A 87 85 CR87 30 3 86 87A 87 85 PLATFORM ROTATE JIB BOOM UP/DOWN CR71 PLATFORM LEVEL TB9 4 1 2 3 1 4 3 OR/BK Y60 Y62 Y19 JIB BOOM RETRACT PLATFORM ROTATE LEFT PLATFORM LEVEL DOWN OR N.O. (SWITCH SHOWN IN UNLOADED POSITION) 2 GN N.C. 7 GN/BK LOAD SENSE GN GN/BK LS19 6 5 Y61 Y63 Y20 JIB BOOM EXTEND PLATFORM ROTATE RIGHT PLATFORM LEVEL UP 7 ES-TZ50D Part No. 84577 TZ-50 8 5 - 105 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5004-182 to TZ5005-210) 5 - 105 5 - 106 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5005-211 to TZ5005-284) 5 - 107 5 - 108 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5005-211 to TZ5005-284) A B C D E F G H I J K L WHT GRN BLK BLK BLK/RED WHT ORG WHT/RED ORG/RED RED/WHT BLU GRN/BLK 1 To Page 3 of 3 ORG/RED BLU/BLK GRN/BLK DE BLU CD10 CD11 GRN/BLK WHT RED BLU BLK/WHT CD9 WHT DC DD PA6 PA5 RED/BLK PA4 PA3 WHT/BLK DB PA2 PA1 RED PA11 RED/WHT RED/WHT WHT/BLK WHT/RED PA10 ORG WHT FLASHING BEACON OPTION BLK DA 3 WHT 2 FB BLK FB1 GRN 1 BLK/RED BLK BLK GRN WHT 2 DOWN LIMIT SWITCHES SHOWN IN STOWED POS. M DF DG DH DJ DK PA7 PA8 DP GROUND CONTROL BOX PA9 TB4A TB2 TB4 3 TB3 CHOKE BN59 FAULT ALARM L4 ENGINE OPTION TB7 87A 87 85 CR77 87A 87 85 CR76 (-) 30 5 86 30 18 86 87A 87 85 87A 87 85 TB22 30 7 86 87A 87 85 L13 L14 L15 RF LED LR LED RR LED + 30 8 86 - 87A 87 85 U16A 0 .1-10 SEC TIME DELAY TB20 TB21 TB23 TB24 CR61 CR86 C4A 3.3V C4 5.1V CD1 CD2 CD3 CD5 CC5CC6 CD6 CD7 CC7CC8 CD8 CC9 CC10 Y34 WHT GRN/WHT RED Y33 BLU/WHT RED Y36 ORG/WHT RED RED/WHT Y35 CD4 GRN/WHT CC3 CC4 BLU/WHT CC2 RED AUTO LEVEL 0-5 VDC SIGNAL 5 6 7 8 CC1 WHT 4 GRN/WHT BLU/WHT ORG/WHT RED/WHT 2 ORG/WHT 1 J BLK RED S7 L12 LF LED TB28 CR28 CR65B LEVEL SENSOR TB17 TB16 WHT/BLK A AUTO LEVEL TB18 BLU C BN90 TB14 H F RIGHT REAR OUTRIGGER RED/WHT C BN51 LEFT REAR OUTRIGGER WHT A WHT F9 BLK CHOKE SOLENOID + - PB12 RED/WHT WHT PB11 RED BLK BLK RED RED PB10 BLK/RED BN50 RIGHT FRONT OUTRIGGER RED PB9 PB8 BN53 LEFT FRONT OUTRIGGER TB32 87A 87 85 87A 87 85 BN52 TB13 1K OHM CR65A 30 3 86 TB11 LOAD 30 1 86 TB12 TB10 TB9 30 6 86 CAPACITOR 4700uF RESISTOR 5 OHM PR5 B5 1 B- B B1 250 AMP 24V BATT 3 T2 TZ-50 Part No. 84577 S2 B+ A1 MOTOR CONTROLLER 8 5 - 108 TB8 30 4 86 U6 CUTOUT D BN60 FUNCTION ENABLE TB15 LS FAULT E U6 CUTOUT 87A 87 85 15 AMP Q7 7 30 2 86 CB1 15 AMP B CR15 - LEVEL SENSOR 6 87A 87 85 + FAULT GROUND CB2 CR1 30 17 86 LOAD CR8 87A 87 85 CHOKE 87A 87 85 START IGNITION P1 30 16 86 10-30 SEC TIME DELAY U16B 30 15 86 TB5 CR64 KS1 5 DOWN ENABLE BN90 ENGINE START GROUND PLAT 4 BN68 MOTOR OUTRIGGER LIMIT SWITCHES OUTRIGGERS SHOWN IN STOWED POSITION (FORCED OPEN) LS12 LS13 LEFT FRONT OUTRIGGER RIGHT FRONT OUTRIGGER LS14 LS15 LEFT REAR OUTRIGGER RIGHT REAR OUTRIGGER ES-TZ50F N September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5005-211 to TZ5005-284) N M L K PB5 PB6 CR78A LIFT CUTOUT BN57 TURNTABLE ROTATE TB31 F GRN/WHT PA12 G GRN PB4 ORG/BLK PB3 H RED PB2 BLK/WHT PB1 I RED/BLK BLUE/BLK WHT/BLK GROUND CONTROL BOX J E C PB7 2 BN93 87A 87 85 DRIVE CONTROL BOX (OPTION) PLATFORM ROTATE (OPTION) TB30 PLATFORM LEVEL UP/DOWN A 1 BN93 30 9 86 B RED WHT/BLK BLU/BLK RED/BLK To Page 3 of 3 BLK/WHT ORG/BLK GRN GRN/WHT 1 TB33 EMERGENCY STOP TB34A BN96 BN95 DOWN ENABLE UP ENABLE BN96 AUTO LEVEL 2 JC5 JOYSTICK CONTROLLER 3 4 5 3 6 P3 BN55 BN54 BN56 SECONDARY BOOM UP/DOWN PRIMARY BOOM UP/DOWN EXTEND/RETRACT TB25 TB32 TB28 TB12 TB22 D BN36 JIB BOOM UP/DOWN BOOM TB26 4 TB29 TB27 TB28 CR72 GRN/WHT BLK BLU/BLK WHT/BLK DN 7 5 5 8 ORG/BLK 6 Y59 BRAKE RELEASE LEFT PROPORTIONAL RIGHT PROPORTIONAL Y50A ORG/BLK ORG ORG FWD/REV RIGHT BOOM EXTEND BOOM RETRACT PRIMARY UP PRIMARY DOWN SECONDARY UP SECONDARY DOWN ROTATE RIGHT ROTATE LEFT OUTRIGGER RETRACT OUTRIGGER EXTEND Y50 WHT BRN ES-TZ50F DM 3 GRN/WHT Y22 FWD/REV LEFT Y53 Y24 WHT BLK BLK/WHT Y26 Y39 2 DL 1 Y25 Y21 ORG W V RED RED/BLK Y52 DN DM DC DP DB DL ORG/BLK U WHT T BLUE BLUE/BLK WHT WHT/BLK GRN/BLK GRN Y23 Y40 S DH DJ RED R P DG BLU N GRN/BLK M L DK TB34 TB35 K RED/WHT 87A 87 85 BLK/WHT 87A 87 85 DD 30 14 86 RED/BLK 87A 87 85 30 13 86 DA DE DF GRN 87A 87 85 30 12 86 BOOM EXTEND 87A 87 85 30 11 86 CR69 CR67 PRIMARY BOOM 30 10 86 CR68 SECONDARY BOOM TURNTABLE ROTATE OUTRIGGER + HM CR70 Y11 7 Y58 8 Part No. 84577 TZ-50 5 - 109 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5005-211 to TZ5005-284) 5 - 109 5 - 110 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5005-211 to TZ5005-284) N M L K J From Page 1 of 3 From Page 2 of 3 I H G F E D C B A 1 WHT GRN BLK BLK BLK/RED WHT ORG WHT/RED ORG/RED RED/WHT BLU GRN/BLK RED WHT/BLK BLU/BLK RED/BLK BLK/WHT ORG/BLK GRN GRN/WHT 2 GRN/WHT PB4 PB3 GRN ORG/BLK PB1 PB2 BLK/WHT RED/BLK PA7 PA8 BLU/BLK WHT/BLK PA6 GRN/BLK PA4 PA5 PA9 BLU RED/WHT PA3 ORG/RED WHT/RED PA2 ORG PA1 WHT 3 BLK/RED 2 BLK EMERGENCY STOP BLK GRN WHT 1 PB5 PA12 PB6 3 PB7 G7 BCI P2 H1 TB1 BN61 BN62 DOWN FUNCTION ENABLE UP FUNCTION ENABLE L4A CR78B BN66 LED TB3 LIFT CUTOUT TURNTABLE ROTATE TB5 TB2 BN2 BN3 TB4 START CHOKE ENGINE OPTION 30 2 86 BN98 PLATFORM ROTATE TB6 87A 87 85 TB8 5 TB7 5.6K BN64 WHT RED SPEED 10K 4 BN67 PLATFORM LEVEL 5.1V SECONDARY BOOM UP/DOWN BN65 BN63 PLATFORM ROTATE (OPTION) BN97 BOOM PRIMARY EXTEND BOOM RETRACT UP/DOWN JIB BOOM UP/DOWN BLK 30 3 86 87A 87 85 CR87 30 4 86 87A 87 85 PLAT ROTATE PLATFORM LEVEL 5.6K CR9 JIB UP/DOWN C71 6 30 5 86 87A 87 85 TB9 PLATFORM CONTROL BOX 7 PLATFORM ROTATE RIGHT TZ-50 Y61 Y62 7 BLU Part No. 84577 6 BLU/BLK PLATFORM ROTATE LEFT Y20 LIMIT SWITCH SHOWN IN UNLOADED POSITION Y60 5 JIB BOOM GRN EXTEND Y19 4 PLATFORM LEVEL UP LS19 3 GRN/BLK JIB BOOM RETRACT 2 ORG 1 ORG/BLK 3 PLATFORM LEVEL DOWN WHT 2 ORG BLK 1 RED 4 Y63 8 5 - 111 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5005-211 to TZ5005-284) 5 - 111 5 - 112 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5005-285 to TZ5010-144) 5 - 113 5 - 114 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5005-285 to TZ5010-144) A B C D E F G H I J K PLATFORM CONTROL BOX 1 BN2 BN3 H1 FAULT ALARM START CHOKE G7 PLATFORM E-STOP POWER L4A LED P2 BCI LS19 3 LOAD SENSE LIMIT SWITCH 4 PA-4 PA-3 PA2 PA1 2 1 DRIVE CONTROLS DRIVE E-STOP POWER 2 BK/RD BK BK DRIVE CONTROL BOX CD10 WH CD11 DE WH/BK DA DF LS18A RD CD-9 RD/BK PA-4 PA-3 PA2 PA1 2 1 BK/WH GN OG WH GN/YELLOW WH 3 LS18 GROUND CONTROL BOX TB3 CB2 15AMP. KS1 P1 RD RD RD TB3 TB2 PLAT TB4 GRD CB1 15AMP. H5 FAULT ALARM BN68 BN90 CHOKE START CR65A TB4A TB4A 4 CR64 (2) GROUND CONTROLS L4 LOAD SENSE LED CR65A (4) L13 L12 5 CR8 (15) CR1 (16) CR15 (17) TB7 CR76 (3) U16B + LOAD L15 CR76 (3) CR75 (1) CR75 (1) - L14 GCON GROUND GRN/WHT CC9 CC8 RED BLU/WHT CC7 CC6 RED ORG/WHT CC5 CC4 RED RED/WHT CC3 BATTERY 24V RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED LS FAULT RELAY R3 BK LEVEL SENSOR RELAY R1 PA11 BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 B CC2 RED PA10 WH IND. STARTER RELAY R16 TZ-50 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH 5 - 114 BK S7 REGULATOR 7 ENGINE OPTION FB STA. M3 8 A U26 FB1 WH - WH BAT. + NO C BAT. C A RD EXCT. F9 50AMP. Q7 B5 ALTERNATOR RD D1 PR5 F PB11 275AMP. F9A 50AMP. RD PB12 RD/WH PB9 F6 BK WH BK RD RD PB10 BK/RD PB8 E B 6 OUTRIGGER LIMIT SWITCHES BATTERY GROUND ES0440C L M N September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5005-285 to TZ5010-144) N M L K J I H G F E D C B A PLATFORM CONTROL BOX PLATFORM CONTROL BOX PLATFORM E-STOP POWER BN61 1 BN62 DOWN ENABLE DOWN ENABLE TB3 TB4 PLATFORM GROUND TB2 2 TB3 R22B 5.6K KEY SIGNAL CR9 CR71 (4) CR87 R14 1 2 10K POT (3) (5) R22C C4B 5.6K PLATFORM GROUND 5.1V PA 7 3 BL RD/WH PA8 PA6 OR/RD GN/BK PA9 WH/RD 8 7 PA5 GR/WH BL/WH 6 5 4 2 1 DC DP OR/WH RD/WH WH RD BK BL/BK 0-5V WH/BK DB DN DM DL LS19 LOAD SENSE LIMIT SWITCH HALL EFFECT WITH ELECTRONIC DAMPING GN/WH DH AUTOLEVEL MODULE FWD/REV SWITCH DGDJ OR WH BL DK BK GN/BK DD RD RD/WH DRIVE CONTROL BOX RIGHT PROPORTIONAL JOYSTICK POWER DRIVE E-STOP POWER LEFT PROPORTIONAL OR/BK UP ENABLE JOYSTICK GROUND DOWN ENABLE GROUND CONTROL BOX TB3 BN59 DOWN ENABLE BN60 UP ENABLE TB9 CR65A TB4A 4 TB10 BN60 BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB32 C4A CR28 (7) (5) CR86 Y36 Y33 Y34 S2 A1 M5 M5 MOTOR BATTERY GROUND 7 GCON GROUND (HARNESS GROUND PLUG) ES0440C 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y35 2 JIB RELAY R4 2 PLAT LEVEL RELAY R3 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 EXTENSION RELAY R14 3 U6 PLATFORM ROTATE RELAY R3 BK 1 B- 2 1 SECONDARY RELAY R12 GN/WH 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 CD8 BK 1 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER CD7 BL/WH 2 CR69 (14) CR68 (12) J CD6 BK 2 1 G6 HM CR67 (13) WH/BK CD5 OR/WH 2 CR70 (11) CR72 (10) (18) L1 BL CD4 1 TB32 TB12 CR86 (18) H CD3 BK 2 1 Y11 2 CD2 2 1 2 BK Y50 2 Y40 BK Y59 2 RD/WH GN/BK 2 1 2 Y50A CD1 L GN BL/BK WH WH OR OR/BK BK K 8 3 1 5 7 2 1 2 Y58 C4 CR77 (6) CR65B TB35 DRIVE OPTION 5 CR28 TB22 CR72 (10) BATTERY 24V TB14 CR65B C5 GCON GROUND R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL GROUND CONTROL BOX TB11 TB8 RR O/R ENABLE 8 TZ-50 5 - 115 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5005-285 to TZ5010-144) 5 - 115 5 - 116 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5005-285 to TZ5010-144) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY BN64 SEC PLATFORM GROUND GN/WH BL/BK 1 6 7 PB7 5 BK BL GN/BK GN GN 1 1 Y61 Y60 BK Y20 Y19 TB31 1 BL PLAT LEVEL ENABLE ROTATE ENABLE BL/BK BN58 BN57 TB11 1 BN93 PLAT ROTATE ENABLE GN JIB MANIFOLD 1 GN/BK OR OR/BK PB7 PB6 PB5 4 OR/BK PB4 PB6 PB5 BK/WH PB3 OR PB4 RD/BK PB2 OR/BK PB3 BL/BK PB1 3 PB2 WH/BK 2 PB1 GROUND CONTROL BOX 3 1 Y63 Y62 TB30 TB33 5 TB34A CR78A (9) SEC ENABLE TB29 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD BN36 - GCON GROUND LIFT CUTOUT RELAY 2 BK BK/WH 2 1 Y26 1 Y52 W V RD RD/BK 2 1 Y22 1 Y23 U T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL 1 Y24 S BL/BK LR O/R R LS14 LF O/R WHT LS12 WHT/BK RR O/R P LS15 N WHT RF O/R CC10 WHT CC1 LS13 1 Y21 2 2 Y25 2 2 ES0440C 2 2 6 7 2 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 2 PLATFORM ROTATE CCW (8) TB27 2 PLATFORM ROTATE CW U16A BN56 TB26 2 JIB EXTEND TB28 CR61 BN54 2 JIB RETRACT BN55 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 PRI ENABLE 4 8 TZ-50 5 - 117 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5005-285 to TZ5010-144) 5 - 117 5 - 118 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5010-145 to TZ5011-131) 5 - 119 5 - 120 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5010-145 to TZ5011-131) A B C D E F G H LS19 1 BN2 BN3 BCI PLATFORM START CHOKE G7 2 K LOAD SENSE LIMIT SWITCH PLATFORM CONTROL BOX PLATFORM GROUND DRIVE CONTROL BOX P4-10 WH P4-11 DE WH/BK DA DF LS18A RD P4-9 RD/BK P1-4 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 BK/WH GN BK/RD DRIVE E-STOP POWER OG P1-2 BK P1-4 P1-1 BK DRIVE CONTROLS LS18 WH P10-3 GN/YELLOW P1-3 P10-2 WH ENGINE OPTION TB3 CB2 15AMP. RD RD RD TB2 PLAT TB4 H5 FAULT ALARM BN68 BN90 CHOKE GRD CB1 15AMP. 4 TB3 KS1 P1 L PLATFORM E-STOP POWER LOAD SENSE POWER LS19A LS19 L4A LED H1 FAULT ALARM CONTROLS TB9 P10-1 3 4 J LOAD SENSE POWER P2 2 LS19A 3 1 I START CR65A TB4A TB4A CR64 (2) GROUND CONTROLS L4 LOAD SENSE LED GROUND CONTROL BOX CR65A (4) L13 L12 TB7 CR76 (3) 5 CR8 (15) U16B CR1 (16) CR15 (17) + LOAD L15 CR76 (3) CR75 (1) CR75 (1) - L14 GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 ORG/WHT P5-5 P5-4 RED RED/WHT P5-3 BATTERY 24V RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED LS FAULT RELAY R3 BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 2 P5-2 RED IND. LEVEL SENSOR RELAY R1 FB1 REGULATOR STARTER RELAY R16 TZ-50 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH ENGINE OPTION P1-11 BK S7 M3 5 - 120 FB STA. 7 8 P1-10 WH - NO U26 P3-A BK BAT. + WH BAT. 3 1 RD EXCT. F9 50AMP. Q7 B5 D1 ALTERNATOR P3-C WH PR5 P3-F RD P8-3 P2-11 RD P8-4 P8-1 P2-12 RD/WH P8-5 P2-9 F6 275AMP. F9A 50AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 OUTRIGGER LIMIT SWITCHES BATTERY GROUND ES0440D M N September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5010-145 to TZ5011-131) N M L K J I H G F E D C B PLATFORM CONTROL BOX PLATFORM CONTROL BOX PLATFORM E-STOP POWER LOAD SENSE POWER BN61 2 TB4 COM + 2 SEC TB2 30A NO AUTOLEVEL MODULE FWD/REV SWITCH NO R22B U35 KEY SIGNAL 5.6K CR9 CR71 (4) CR87 R14 CR55 CR55 10K POT (3) (5) R22C C4B 5.6K PLATFORM GROUND 5.1V P1-7 P1-8 3 BL GN/BK P1-6 RD/WH P9-8 P9-7 P1-9 OR/RD P1-5 WH/RD GR/WH BL/WH P9-6 P9-5 P9-4 P9-2 P9-1 DC DP OR/WH RD/WH WH RD BK BL/BK 0-5V WH/BK DB DN DM DL 2 TB3 - 3 HALL EFFECT WITH ELECTRONIC DAMPING GN/WH OR DH BK WH BL DGDJ RD GN/BK DK RIGHT PROPORTIONAL JOYSTICK POWER RD/WH DD LEFT PROPORTIONAL OR/BK UP ENABLE JOYSTICK GROUND DOWN ENABLE DRIVE E-STOP POWER GROUND CONTROL BOX DOWN ENABLE TB3 5 PLATFORM GROUND 1 BN62 DOWN ENABLE R20 4.7K LS19A LS19 DRIVE CONTROL BOX A GROUND CONTROL BOX TB3 BN59 DOWN ENABLE BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE TB11 TB8 RR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB14 CR65B TB32 C4A CR28 (7) (5) CR86 Y36 Y33 Y34 S2 A1 M5 M5 MOTOR 7 GCON GROUND (HARNESS GROUND PLUG) ES0440D 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y35 2 JIB RELAY R4 2 PLAT LEVEL RELAY R3 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 EXTENSION RELAY R14 3 U6 PLATFORM ROTATE RELAY R3 BK 1 B- 2 1 SECONDARY RELAY R12 GN/WH 1 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 P4-8 BK 2 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER P4-7 BL/WH 1 CR69 (14) CR68 (12) P3-J P4-6 BK 2 G6 HM CR67 (13) WH/BK P4-5 OR/WH 2 L1 BL P4-4 1 CR70 (11) CR72 (10) (18) P3-H P4-3 BK 2 1 Y11 2 P4-2 2 1 2 BK Y50 2 1 Y40 BK Y59 2 RD/WH 2 P4-1 GN BK BL/BK WH WH OR OR/BK BK P3-L GN/BK P3-K P3-M P7-8 P7-3 P7-1 P7-5 P7-7 P7-2 1 2 Y50A TB32 TB12 CR86 (18) TB35 2 C4 CR77 (6) CR65B CR72 (10) 5 CR28 TB22 C5 Y58 R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL BATTERY GROUND 4 TB10 BN60 BATTERY 24V UP ENABLE TB9 CR65A TB4A GCON GROUND BN60 8 TZ-50 5 - 121 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5010-145 to TZ5011-131) 5 - 121 5 - 122 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5010-145 to TZ5011-131) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) BN64 SEC CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY PLATFORM CONTROLS PLATFORM GROUND P6-1 BK GN/WH BL/BK BL P6-6 P6-7 P2-7 GN/BK P6-5 GN GN P6-4 Y20 Y19 TB31 1 1 Y61 Y60 BK TB11 1 BL PLAT LEVEL ENABLE ROTATE ENABLE BL/BK BN58 BN57 1 BN93 PLAT ROTATE ENABLE GN JIB MANIFOLD 1 GROUND CONTROLS GN/BK OR OR/BK P2-7 P2-6 P2-5 P2-6 OR/BK P2-4 OR BK/WH P2-3 P6-3 P2-4 RD/BK P2-2 P6-2 P2-3 BL/BK P2-1 OR/BK P2-2 WH/BK P2-5 P2-1 GROUND CONTROL BOX 3 1 Y63 Y62 TB30 TB33 TB34A CR78A (9) SEC ENABLE - 1 Y21 2 2 Y25 2 2 2 GCON GROUND (HARNESS GROUND PLUG) LIFT CUTOUT RELAY R9 2 BK BK/WH 2 1 Y26 1 Y52 P3-W P3-V RD RD/BK 2 1 Y22 1 Y23 P3-U P3-T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL 1 Y24 P3-S BL/BK LR O/R P3-R LS14 LF O/R WHT LS12 WHT/BK RR O/R P3-P LS15 P3-N WHT RF O/R P5-10 WHT P5-1 LS13 TB29 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD GCON GROUND BN36 ES0440D 2 2 6 7 EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 2 PLATFORM ROTATE CCW (8) TB27 2 PLATFORM ROTATE CW U16A BN56 TB26 2 JIB EXTEND TB28 CR61 BN54 2 JIB RETRACT BN55 5 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 PRI ENABLE 4 8 TZ-50 5 - 123 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5010-145 to TZ5011-131) 5 - 123 5 - 124 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5011-132 to TZ5011-310) 5 - 125 5 - 126 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5011-132 to TZ5011-310) A B C D E F G H LS19 1 BN2 BN3 PLATFORM START CHOKE 2 K LOAD SENSE LIMIT SWITCH PLATFORM CONTROL BOX PLATFORM GROUND P1-4 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 ENGINE OPTION DRIVE CONTROLS DRIVE E-STOP POWER BK/RD BK BK LS18 DRIVE CONTROL BOX P4-10 WH P4-11 DE WH/BK DA DF LS18A RD P4-9 RD/BK P1-4 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 BK/WH GN OG WH GN/YELLOW WH HORN OPTION GROUND CONTROL BOX TB3 CB2 15AMP. RD RD RD TB2 PLAT TB4 H5 FAULT ALARM BN68 BN90 CHOKE GRD CB1 15AMP. 4 TB3 KS1 P1 L PLATFORM E-STOP POWER LOAD SENSE POWER LS19A LS19 L4A LED H1 FAULT ALARM CONTROLS TB9 3 4 J LOAD SENSE POWER P2 2 LS19A 3 1 I START CR65A TB4A TB4A CR64 (2) GROUND CONTROLS L4 LOAD SENSE LED CR65A BCI G7 (4) L13 L12 5 CR8 (15) CR1 (16) CR15 (17) TB7 CR76 (3) U16B + LOAD L15 CR75 (1) CR75 (1) - L14 CR76 (3) GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 ORG/WHT P5-5 BATTERY 24V RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 LEVEL SENSOR TILT ALARM Part No. 84577 P5-4 RED BK ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 TZ-50 STARTER RELAY R16 5 - 126 STARTER MOTOR CHOKE RELAY R17 CHOKE RELAY IGNITION RELAY R15 SPARK PLUG IGNITION COIL ENGINE OPTION 2 LF OUTRIGGER LED IND. RED/WHT P5-3 REGULATOR M3 OIL LEVEL SWITCH 8 FB1 LS FAULT RELAY R3 S7 P5-2 RED FB STA. OUTRIGGER LIMIT SWITCHES LEVEL SENSOR RELAY R1 7 P1-11 BK - NO U26 P1-10 WH BAT. + 3 1 WH EXCT. BAT. P3-A BK D1 ALTERNATOR P3-C WH ODR1 RD B5 CR20 F9 50AMP. Q7 P3-F RD P8-3 PR5 P2-11 RD P8-4 P8-1 P2-12 RD/WH P8-5 P2-9 F6 275AMP. F9A 50AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 ES0440E BATTERY GROUND M N September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5011-132 to TZ5011-310) N M L K J I H G F E D C B PLATFORM CONTROL BOX A PLATFORM CONTROL BOX PLATFORM E-STOP POWER LOAD SENSE POWER BN61 DOWN ENABLE R20 4.7K LS19A 1 BN62 DOWN ENABLE TB3 LS19 2 5 PLATFORM GROUND TB4 COM + 2 SEC TB2 30A NO AUTOLEVEL MODULE FWD/REV SWITCH NO R22B U35 KEY SIGNAL 5.6K CR9 CR71 (4) CR87 R14 CR55 CR55 10K POT (3) (5) R22C C4B 5.6K PLATFORM GROUND 5.1V P1-7 P1-8 3 BL GN/BK P1-6 RD/WH P9-8 P9-7 P1-9 OR/RD P1-5 WH/RD GR/WH BL/WH P9-6 P9-5 P9-4 P9-2 P9-1 DC DP OR/WH RD/WH WH RD BK BL/BK 0-5V WH/BK DB DN DM DL 2 TB3 - 3 HALL EFFECT WITH ELECTRONIC DAMPING GN/WH DH OR DGDJ RIGHT PROPORTIONAL DK BK WH BL DD RD GN/BK GROUND CONTROL BOX RD/WH DRIVE CONTROL BOX JOYSTICK POWER DRIVE E-STOP POWER LEFT PROPORTIONAL OR/BK UP ENABLE JOYSTICK GROUND DOWN ENABLE GROUND CONTROL BOX TB3 BN59 DOWN ENABLE BN52 BN53 LF O/R ENABLE UP ENABLE BN51 BN50 RF O/R ENABLE LR O/R ENABLE TB11 TB8 RR O/R ENABLE CR77 (6) BN49 TB20 ENABLE TB21 TB23 CR65A (4) TB24 TB16 TB15 TB17 TB14 CR65B TB32 C4A CR28 (7) (5) CR86 Y36 Y33 Y34 S2 A1 M5 M5 MOTOR 7 GCON GROUND (HARNESS GROUND PLUG) ES0440E 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 HOUR METER Y35 2 JIB RELAY R4 2 PLAT LEVEL RELAY R3 2 MOTOR CONTROLLER PRIMARY RELAY R13 B+ Y39 ROTATE RELAY R11 T2 EXTENSION RELAY R14 3 U6 PLATFORM ROTATE RELAY R3 BK 1 B- 2 1 SECONDARY RELAY R12 GN/WH 1 47 mH, 2.5 AMP., 0.034 OHM OUTRIGGER RELAY R10 P4-8 BK 2 GROUND CONTROLS GROUND 6 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER P4-7 BL/WH 1 CR69 (14) CR68 (12) P3-J P4-6 BK 2 G6 HM CR67 (13) WH/BK P4-5 OR/WH 2 L1 BL P4-4 1 CR70 (11) CR72 (10) (18) P3-H P4-3 BK 2 1 Y11 2 P4-2 2 1 2 BK Y50 2 1 Y40 BK Y59 2 RD/WH 2 P4-1 GN BK BL/BK WH WH OR OR/BK BK P3-L GN/BK P3-K P3-M P7-8 P7-3 P7-1 P7-5 P7-7 P7-2 1 2 Y50A TB32 TB12 CR86 (18) TB35 2 C4 CR77 (6) CR65B CR72 (10) 5 CR28 TB22 C5 Y58 R22 1K OHM (5) CR61 (8) TB18 TB11 TB13 TB5 AUTOLEVEL BATTERY GROUND 4 TB10 BN60 BATTERY 24V UP ENABLE TB9 CR65A TB4A GCON GROUND BN60 8 TZ-50 5 - 127 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5011-132 to TZ5011-310) 5 - 127 5 - 128 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5011-132 to TZ5011-310) N M L K J I H G F E D C B A 1 TB3 BN66 ROTATE ENABLE BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE CR78B (1) CR78B (1) BN97 JIB ENABLE BN65 EXT BN63 PRI ENABLE ENABLE ENABLE CR71 CR9 CR87 (3) (4) (5) 2 LIFT CUTOUT RELAY BN64 SEC PLATFORM GROUND P6-1 BK GN/WH BL/BK BL P6-6 P6-7 P2-7 GN GN/BK P6-5 GN Y20 Y19 TB31 1 1 Y61 Y60 BK TB11 1 BL PLAT LEVEL ENABLE ROTATE ENABLE BL/BK BN58 BN57 1 BN93 PLAT ROTATE ENABLE GN JIB MANIFOLD 1 GN/BK OR OR/BK P2-7 P2-6 P2-5 P6-4 OR/BK P2-4 P2-6 P2-5 BK/WH P2-3 OR P2-4 RD/BK P2-2 P6-3 P2-3 BL/BK P2-1 P6-2 P2-2 WH/BK OR/BK P2-1 3 1 Y63 Y62 TB30 TB33 5 TB34A CR78A (9) SEC ENABLE TB29 CR70(11) CR68(12) CR67(13) CR69(14) + LOAD BN36 - GCON GROUND 1 Y21 2 2 Y25 2 2 2 LIFT CUTOUT RELAY R9 2 BK BK/WH 2 1 Y26 1 Y52 P3-W P3-V RD RD/BK 2 1 Y22 1 Y23 P3-U P3-T 1 Y53 1 OUTRIGGER LIMIT SWITCHES BL 1 Y24 P3-S BL/BK LR O/R P3-R LS14 LF O/R WHT LS12 WHT/BK RR O/R P3-P LS15 P3-N WHT RF O/R P5-10 WHT P5-1 LS13 ES0440E 2 2 PLATFORM ROTATE CCW (8) TB27 2 2 PLATFORM ROTATE CW U16A BN56 TB26 2 JIB EXTEND TB28 CR61 BN54 2 JIB RETRACT BN55 CR78A (9) JIB ENABLE PLAT LEVEL EXTEND TB25 EXT ENABLE PLAT LEVEL RETRACT TB32 PRI ENABLE 4 6 7 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 8 TZ-50 5 - 129 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5011-132 to TZ5011-310) 5 - 129 5 - 130 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE (from serial number TZ5011-311) 5 - 131 5 - 132 Section 5 • Schematics September 2014 Electrical Schematic - AS/CE, 1 of 3 (from serial number TZ5011-311) A B C D E F G H 1 1 3 J K BN3 BN2 CHOKE START PLATFORM CONTROLS PLATFORM CONTROL BOX FAULT ALARM TB9 PLATFORM GROUND P1-4 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 ENGINE OPTION DRIVE CONTROLS DRIVE E-STOP POWER HORN OPTION BK/RD BK BK LS18 DRIVE CONTROL BOX WH P4-11 P4-10 DE WH/BK DA DF LS18A RD P4-9 RD/BK P1-4 P1-3 P1-2 P1-1 P10-3 P10-2 P10-1 BK/WH GN WH OG GN/YELLOW WH 3 GROUND CONTROL BOX TB3 CB2 15AMP. 4 P1 RD RD RD KS1 PLAT M PLATFORM E-STOP POWER LOAD SENSE POWER LS19A LS19 L4A LED H1 L LS19 LS19A LOAD SENSE 4 2 LIMIT SWITCH LOAD SENSE POWER P2 2 I TB3 TB2 TB4 GRD BN68 START BN90 CHOKE CB1 15AMP. H5 FAULT ALARM CR65A TB4A TB4A L4 CR64 GROUND (2) LOAD SENSE LED CONTROLS CR65A (4) BCI G7 5 200 OHM 10W L13 L12 L14 L15 TB7 (15) U16B CR1 CR15 CR8 (16) (17) LOAD CR76 (3) + CR76 CR75 CR75 - (3) (1) (1) GCON GROUND RED GRN/WHT P5-9 P5-8 RED BLU/WHT P5-7 P5-6 RED ORG/WHT P5-5 P5-4 RED RED/WHT P5-3 P5-2 BATTERY 24V U6-B+ RR OUTRIGGER LED LR OUTRIGGER LED RF OUTRIGGER LED LF OUTRIGGER LED BK FLASHING BEACON OPTION MOTOR CONTROLLER CUTOUT RELAY R3 TILT ALARM LEVEL SENSOR OFF DELAY RELAY ODR1 2 TO 3 SECONDS ALTERNATOR TIME DELAY U16B 10 TO 30 SECONDS CHARGING RELAY R16 Part No. 84577 2 LS FAULT RELAY R3 IND. OUTRIGGER LIMIT SWITCHES LEVEL SENSOR RELAY R1 REGULATOR P3-X FB1 S7 STARTER RELAY R16 STARTER MOTOR TZ-50 CHOKE RELAY R17 5 - 132 CHOKE RELAY ENGINE OPTION IGNITION RELAY R15 SPARK PLUG IGNITION COIL OIL LEVEL SWITCH 8 BK FB STA. M3 QD1 P1-11 - WHT BAT. + NO U26 3 1 EXCT. BAT. P1-10 WH D1 ALTERNATOR P3-A BK ODR1 P3-C WH CHARGER CR20 RD 7 PR5 50 AMP. F9 P3-F RD Q7 B5 RD P8-4 P8-3 P2-11 P8-1 P2-12 RD/WHT P8-5 F9A 50AMP. QD1 P2-9 F6 275AMP. BK P8-2 WH BK RD RD P2-10 BK/RD P2-8 P3-D P3-E P3-B 6 ES0440G BATTERY GROUND N September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 2 of 3 (from serial number TZ5011-311) N M L K J I H G F E D C B PLATFORM CONTROL BOX PLATFORM CONTROL BOX PLATFORM E-STOP POWER LOAD SENSE POWER BN61 R20 4.7K LS19A LS19 FWD/REV SWITCH RIGHT PROPORTIONAL 2 AUTOLEVEL MODULE HALL EFFECT WITH ELECTRONIC DAMPING - TB4 COM TB2 30A NO TB3 NO U35 2 R22B 5.6K R14 10K POT R22C 5.6K CR55 C4B 5.1V CR71 (3) CR9 (4) CR87 (5) PLATFORM GROUND P1-7 P1-8 3 BL GN/BK P1-6 RD/WH P1-9 OR/RD P9-8 P9-7 P9-6 P1-5 WH/RD GR/WH BL/WH OR/WH RD/WH P9-5 P9-1 DB DN DM DL DC DP 3 + CR55 WH RD P9-4 BK P9-2 GN/WH OR OR/BK BK KEY SIGNAL BL/BK 0-5V WH/BK LEFT PROPORTIONAL JOYSTICK GROUND RD DG DJ DH JOYSTICK POWER DK WH BL DD GN/BK GROUND CONTROL BOX RD/WH DRIVE CONTROL BOX UP ENABLE UP ENABLE TB3 2 SEC DOWN ENABLE 1 BN62 DOWN ENABLE 5 PLATFORM GROUND DRIVE E-STOP POWER A GROUND CONTROL BOX TB3 BN59 BN60 DOWN ENABLE TB9 CR65A TB4A BN53 BN52 BN60 UP ENABLE TB20 RR O/R ENABLE LR O/R ENABLE TB24 (4) (5) CR61 (8) CR28 (7) (10) CR86 CR86 (18) (18) TB32 TB12 CR77 (6) CR70 (11) CR72 (10) CR68 (12) CR67 (13) GCON GROUND 6 HOUR METER JIB RELAY R4 PLATFORM ROTATE RELAY R3 7 GCON GROUND (HARNESS GROUND PLUG) ES0440G 0-5 V SIGNAL RELAY 5.1V ZENER CAPACITOR RELAY 5 OHM RESISTOR 4700uF CAPACITOR 0-5 V SIGNAL RELAY SPEED RELAY RR OUTRIGGER LR OUTRIGGER RF OUTRIGGER LF OUTRIGGER OUTRIGGER RETCAT OUTRIGGER EXTEND AUTOLEVEL RELAY R8 BRAKE DUMP FWD/REV FWD/REV RIGHT PROPORTIONAL LEFT PROPORTIONAL Part No. 84577 PLAT LEVEL RELAY R3 M5 MOTOR PRIMARY RELAY R13 M5 EXTENSION RELAY R14 D1 ROTATE RELAY R11 A1 SECONDARY RELAY R12 1 U6 3 BM B+ MOTOR CONTROLLER OUTRIGGER RELAY R10 Y34 2 DOWN CUTOUT RELAY R6 5.1V ZENER 3.3V ZENER 12 1 HM G6 CR69 (14) P3-J WH/BK Y33 BK Y36 GN/WH Y35 12 1 C4 47 mH, 2.5 AMP, 0.034 OHM UB-6+ BATTERY GROUND C4A CR65B (5) P3-H BL P4-7 P4-8 BK BK 2 BK 1 2 BL/WH Y39 2 P4-6 BK OR/WH BK RD/WH 12 1 2 P4-5 P4-4 P4-3 P4-2 P4-1 1 Y50 Y11 2 P3-LGN/BK GN Y40 1 2 P3-K BK 1 Y50A TB32 C5 L1 1 1 Y59 2 P3-M P7-8 BL/BK P7-3 WH OR BK P7-1 WH P7-5 P7-2 P7-7 OR/BK 1 5 CR28 CR72 TB35 R22 1K OHM CR65B TB15 TB22 Y58 TB16 TB14 TB17 TB18 4 TB11 TB13 CR65A AUTOLEVEL ENABLE BATTERY 24V (6) TB5 TB23 TB21 TB10 TB11 TB8 CR77 BN51 BN50 RF O/R ENABLE LF O/R ENABLE BN49 GCON GROUND UP ENABLE 8 TZ-50 5 - 133 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5011-311) 5 - 133 5 - 134 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE, 3 of 3 (from serial number TZ5011-311) N M L K J I H G F E D C B A PLATFORM CONTROL BOX 1 TB3 BN98 PLAT ROTATE ENABLE BN67 PLAT LEVEL ENABLE BN66 ROTATE ENABLE CR78B (1) CR78B BN65 EXT ENABLE BN97 JIB ENABLE CR71 CR9 (3) CR87 (4) (5) PLATFORM GROUND P6-6 P6-7 P6-1 GN/WH BL/BK BL BK 1 Y20 TB31 TB33 TB34A CR78A (9) TB32 EXT ENABLE JIB ENABLE BN55 BN56 BN36 TB25 TB26 Y19 CR78A TB27 LIFT CUTOUT RELAY R9 BK BK/WH P3-W P3-V RD RD/BK P3-U P3-T BL BL/BK P3-S P3-R WHT LF O/R RR O/R LS14 P3-P LS12 WHT/BK RF O/R P3-N LS15 WHT WHT P5-10 P5-1 LS13 LR O/R 1 OUTRIGGER LIMIT SWITCHES Y24 Y53 Y23 2 Y22 Y52 2 2 Y26 Y21 2 2 5 ES0440G 2 2 PLATFORM ROTATE CW GCON GROUND 2 PLATFORM ROTATE CCW LOAD - 2 JIB EXTEND (14) (13) Y63 Y62 JIB RETRACT CR69 CR67 (12) PLAT LEVEL EXTEND CR68 (11) 2 PLAT LEVEL RETRACT CR70 + 1 Y61 Y60 2 JIB MANIFOLD TB28 U16A (8) 1 (9) TB29 CR61 4 TB30 SEC PRI ENABLE ENABLE BN54 BK 1 BL 1 BL/BK GN/BK 1 GN TB11 OR OR/BK P2-7 OR P2-7 OR/BK GN P6-3 P2-5 PLAT LEVEL ENABLE ROTATE ENABLE 3 BN93 PLAT ROTATE ENABLE BN58 BN57 P6-5 P6-2 OR/BK P2-4 P2-6 P2-5 BK/WH P2-3 GN P2-4 RD/BK P2-2 GN/BK P2-3 BL/BK P2-1 P6-4 P2-2 WH/BK GROUND CONTROLS P2-6 P2-1 GROUND CONTROL BOX 2 LIFT CUTOUT RELAY (1) BN63 PRI ENABLE BN64 SEC ENABLE 6 7 Y25 2 2 2 GCON GROUND (HARNESS GROUND PLUG) EXTENSION EXTEND EXTENSION RETRACT PRIMARY EXTEND PRIMARY RETRACT SECONDARY EXTEND SECONDARY RETRACT ROTATE CW ROTATE CCW AUTOLEVEL TIME DELAY U16A 0.1 TO 10 SECONDS AUTOLEVEL RELAY R8 Part No. 84577 8 TZ-50 5 - 135 September 2014 Section 5 • Schematics Electrical Schematic - AS/CE (from serial number TZ5011-311) 5 - 135 5 - 136 Section 5 • Schematics September 2014 Hydraulic Schematic (to serial number TZ5006-510) 5 - 137 5 - 138 Section 5 • Schematics September 2014 Hydraulic Schematic (to serial number TZ5006-510) A B C D E F H EXTENSION CYLINDER BRAKE RELEASE LEFT DRIVE MOTOR Y36 R 0.037 in 0.94 mm D2 D3 BH Y50 Y50A BI 10 psi/0.7 bar 10 psi 0.7 bar BA BK BO Y58 Y59 4 E 0.090 in 2.3 mm BF 80 psi 5.5 bar R E E A1 A2 B1 CB 3000 psi 207 bar 4.5:1 1000 psi 69 bar 3:1 B2 PE Y52 PD LS I Y53 Y25 H J 0.046 in 1.17 mm 8 Part No. 84577 PLD PRL PRR AK 3:1 AC Y61 Y21 AF 3000 psi 207 bar 135 psi / 9.3 bar Y22 Y24 Y23 Q 0.080 in 2 mm E 0.040 in 1 mm AD AE R AI AJ Y19 Y20 Y62 Y63 P 0.035 in 0.89 mm 0.055 in 1.4 mm 5 T 80 psi 5.5 bar 0.040 in 1 mm AH 1 2 0.040 in 1 mm AG JIB MANIFOLD 1 MODELS WITHOUT PLATFORM ROTATE 4 FROM TZ5005-274 2 MODELS WITH PLATFORM ROTATE 5 FROM TZ5005-430 3 MODELS WITHOUT DRIVE OPTION 6 3:1 TO TZ5005-273 4.5:1 FROM TZ5005-274 HYDRAULIC TANK 7 PLU Y60 AA TJ M 6 JD D 600 psi 41 bar FUNCTION MANIFOLD 2.8 gpm 10.6 L/min TZ-50 JU AB C T1 SEC 1 RR PJ 80 psi 5.5 bar A 3 2.8 gpm 10.6 L/min RL B P Y26 P1 P1 SEC 2 5 - 138 PU 4 P2 MODELS WITH DRIVE OPTION SD F L HYDRAULIC POWER UNIT MASTER CYLINDER 1600 psi 110 bar Y39 3000 psi 207 bar 3000 psi 207 bar 4.5:1 4.5:1 TO TZ5004-218 3:1 FROM TZ5004-219 AUSTRALIA MODELS ONLY SU PR 3000 psi 207 bar 3:1 Y40 BC 5 3000 psi 207 bar 1.5:1 0.037 in 0.94 mm K 0.090 in 2.3 mm 3000 psi 207 bar 3000 psi 207 bar 3:1 6 O N PLATFORM ROTATE (OPTION) PLATFORM LEVEL 24.9 CU IN / REV 408 CC / REV M BD 80 psi 5.5 bar R G BM BB E Y34 G1 DRIVE MANIFOLD (OPTION) N SLAVE CYLINDER RIGHT REAR OUTRIGGER CYLINDER 0.037 in 0.94 mm BJ JIB BOOM 0.037 in 0.94 mm Y33 3000 psi 207 bar 10:1 3000 psi 207 bar 10:1 Y11 CA BG M PRIMARY BOOM LIFT CYLINDER R LEFT REAR OUTRIGGER CYLINDER BE 3 SECONDARY BOOM LIFT CYLINDER 0.090 in 2.3 mm BL L CD D4 BN K TURNTABLE ROTATE CF 2 D1 J CC RIGHT DRIVE MOTOR Y35 B I RIGHT FRONT OUTRIGGER CYLINDER LEFT FRONT OUTRIGGER CYLINDER 1 G HSTZ50DC F September 2014 Section 5 • Schematics Hydraulic Schematic (from serial number TZ5006-511) N M L LEFT DRIVE MOTOR K J RIGHT DRIVE MOTOR I LEFT FRONT OUTRIGGER CYLINDER H G SECONDARY BOOM LIFT CYLINDER EXTENSION CYLINDER RIGHT FRONT OUTRIGGER CYLINDER F E D C 1 R D1 D2 D3 E E LEFT REAR OUTRIGGER CYLINDER 200 psi 13.8 bar BL 3000 psi 207 bar 10:1 CB CA 3000 psi 207 bar 10:1 R 0.037 in 0.94 mm BJ 10 psi/0.7 bar 10 psi 0.7 bar BA 3000 psi 207 bar 4.5:1 BI BO A1 80 psi 5.5 bar BF 80 psi 5.5 bar 0.090 in 2.3 mm B1 MASTER CYLINDER 3 B2 PE PR SU SD PU PD LS RL RR JU JD I B 1600psi 110bar M 3000 psi 207 bar 3:1 PLU H AF 3:1 AC R 135 psi / 9.3 bar P AD J PJ 3000 psi 207 bar L A 0.046 in 1.17 mm C P1 Q 0.080 in 2 mm E 0.040 in 1 mm 80 psi 5.5 bar P1 T1 2.8 gpm 10.6 L/min 2.8 gpm 10.6 L/min 3 4 AE N 0.090 in 2.3 mm PRR AK 3000 psi 207 bar AA 600 psi 41 bar F K PRL D P 0.035 in 0.9 mm AI AJ 0.055 in 0.040 in 1.4 mm 80 psi 1 mm 5.5 bar AH 1 BC MODELS WITH DRIVE OPTION PLD AB O BD P2 HYDRAULIC POWER UNIT AUSTRALIA MODELS ONLY E A2 3000 psi 207 bar 4.5:1 3000 psi 207 bar 3:1 0.037 in 0.94 mm G DRIVE MANIFOLD (OPTION) BM BB 1000 psi 69 bar 3:1 3000 psi 207 bar 3:1 3000 psi 207 bar 1.5:1 R E G1 BK 2 24.9 CU IN / REV 408 CC / REV RIGHT REAR OUTRIGGER CYLINDER BH BG PLATFORM ROTATE (OPTION) SLAVE CYLINDER 0.037 in 0.94 mm 0.090 in 2.3 mm BE PLATFORM LEVEL R D4 BN JIB BOOM CD 0.037 in 0.94 mm B A PRIMARY BOOM LIFT CYLINDER TURNTABLE ROTATE CC B TJ FUNCTION MANIFOLD 2 0.040 in 1 mm AG T JIB MANIFOLD 5 M SEC 2 SEC 1 HYDRAULIC TANK 1 MODELS WITHOUT PLATFORM ROTATE 2 MODELS WITH PLATFORM ROTATE 3 MODELS WITHOUT DRIVE OPTION HSTZ50 G 6 7 8 Part No. 84577 TZ-50 5 - 139 September 2014 Section 5 • Schematics Hydraulic Schematic (from serial number TZ5006-511) 5 - 139 5 - 140
