Download Aspire 6920 Series Service Guide

Aspire 6920 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire6920 service guide.
Date
II
Chapter
Updates
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN
MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Operating system: Windows Vista™
NOTE: Windowsl® VistaTM Capable PCs come with Windows® XP installed, and can be upgraded
to Windows® VistaTM. For more information on Windows® VistaTM and how to upgrade, go
to: Microsoft.com/windowsvista.
Platform and memroy
• Intel® Centrino® Duo mobile processor technology, featuring:
• Intel® Core™2 Duo mobile processor
• Mobile Intel® GM965/PM965 Express Chipset
• Intel® Wireless WiFi Link Wi-Fi CERTIFIED® network connection
• Intel® PRO/Wireless Wi-Fi CERTIFIED® network connection.
• Dual-Channel DDR2 SDRAM support
• Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules
Display and graphics
• Mobile Intel® GM965/PM965 Express Chipset (for selected models)
• NVIDIA® GeForce® 9500M GS with 512MB of dedicated VRAM supporting TurboCache™ (for
selected models)
TV-tuner
• Digital TV-tuner supporting DVB-T
Audio
• Dolby® -certified surround sound system with two built-in stereo speakers and one subwoofer
supporting lowfrequency effects
• S/PDIF (Sony/Philips Digital Interface) support for digital speakers
• Built-in stereo microphones
Chapter 1
1
Storage subsystem
• 2.5" hard disk drive
• Optical drive options:
• Blu-ray Disc™ (BD) drive (for selected models)
• DVD-Super Multi double-layer drive
• 6-in-1 card reader
Input devices
• 88-/89-key keyboard
• Touchpad pointing device
• Acer CineDash media console capacitive human interface device, including: capacitive
human interface device.
Communication
• Acer Video Conference, featuring:
• Integrated Acer Crystal Eye webcam
• Acer Video Conference Manager software
• Acer PureZone technology
• Optional Acer Xpress VoIP phone
• WLAN: Intel® Wireless WiFi Link network connection or Intel® PRO/Wireless network connection
• WPAN: Bluetooth® 2.0+EDR
• LAN: Gigabit Ethernet, Wake-on-LAN ready
• Modem: 56K ITU V.92
I/O Ports
• ExpressCard™/54 slot
• 6-in-1 card reader (SD™, MMC, MMCplus™, MS, MS PRO, xD)
• Four USB 2.0 ports
• HDMI™ port with HDCP support (for selected models)
• Consumer infrared (CIR) port
• External display (VGA) port
• Headphone/speaker/line-out jack with S/PDIF support
• Microphone-in jack
• Line-in jack
• Ethernet (RJ-45) port
• Modem (RJ-11) port
NOTE: • HDCP is acronym for High-bandwidth Digital Content Protection. An encryption system for enforcing
digital rights management (DRM) over DVI and HDMI interfaces
2
Chapter 1
Environment
• Temperature:
•operating:
5 ° C to 35 ° C
•Non-operating:
•Humidity
(non-condensing):
•operating:
20%~80%
•Non-operating:
Chapter 1
-20 ° C to 65 ° C
20%~80%
3
System Block Diagram
4
Chapter 1
Board Layout
Chapter 1
5
6
Chapter 1
Your Acer Notebook tour
After knowing your computer features, let us show you around your new Aspire computer.
Chapter 1
7
Closed Front View
8
Chapter 1
Left View
Chapter 1
9
Right View
10
Chapter 1
Chapter 1
11
Base view
12
Chapter 1
Indicators
The computer has several easy-to-read status indicators.
The front panel indicators are visible even when the computer cover is closed up.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Easy-Launch Buttons
Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are:
WLAN, Internet, email, Bluetooth and Acer Empowering Technology.
Chapter 1
13
The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To
set the Web browser, mail and programmable buttons, run the Acer Launch Manager.
Touchpad Basics
The following teaches you how to use the touchpad:
14
Chapter 1
Move your finger across the touchpad (2) to move the cursor.
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the touchpad is
the same as clicking the left button.
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your
cursor pressing on the right scroll bar of Windows applications.
NOTE: When using the touchpad, keep it - and your infers - dry and clean. The touchpad is sensitive to finger
movements; hence, the lighter the touch, the better the response. Tapping too hard will not increase the
touchpad’s responsiveness.
Chapter 1
15
Using the Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock Keys and embedded numeric keypad
The keyboard has three lock keys which you can toggle on and off.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
16
Num Lock On
Num Lock Off
Number keys on embedded
keypad
Type numbers in a normal
manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using
cursor-control keys.
Hold <Fn> while using
cursor-control keys.
Main keyboard keys
Hold <Fn> while typing
letters on embedded
keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like sreen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Chapter 1
17
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.
To type:
18
Chapter 1
The Euro symbol
1.
Open a text editor or word processor.
2.
Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then
press the<5> symbol at the upper-center of the keyboard.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign
1. Open a text editor or word processor.
2.
Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the
<4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
Chapter 1
19
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and
manage your new Acer notebook. It features the following handy utilities:
• Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home
Theater on your system.
• Acer ePower Management optimizes battery usage via customizable power plans.
• Acer eDataSecurity Management protects data with passwords and encryption (for selected
models).
• Acer eRecovery Management backs up and recovers data flexibly, reliablyand completely.
• Acer eSettings Management accesses system information and adjusts settings easily.
For more information, press the <
> key to launch the Empowering Technology menu, then click on the
appropriate utility and select the Help or Tutorial function.
Empowering Technology password
You must set the Empowering Technology password to use the password
protection feature of Acer eRecovery Management to protect your data.
To set the Empowering Technology password:
1 Launch Acer eRecovery Management.
2 Click the Restore tab.
3 Click Password settings. The Empowering Technology Password Center dialog box pops up.
4 Click Create a new password.
5 In the Create a New Password dialog box, key in and confirm your password in the appropriate boxes.
Your password should have a minimum of 4 and a maximum of 12 characters.
6 Enter a password hint that will help you remember your password.
20
Chapter 1
7 Make sure the box Use for Acer eRecovery Management is checked.
8 Click OK to set the password.
Acer eAudio Management
Acer eAudio Management allows you to easily control the enhanced sound
effects of Dolby Home Theater on your system. Select Movie or Game mode to
experience the awesome realism of 5.1-channel audio output from the speakers
fitted to your system via Dolby Surround sound technology. Music mode lets
you enjoy your favorite tunes, in vivid detail.
Chapter 1
21
To choose your playback device, click the icon on the upper right side of
the Acer eAudio Management window.
Acer ePower Management
Acer ePower Management features a straightforward user interface for
configuring your power management options. To access this utility, select Acer
ePower Management from the Empowering Technology toolbar, run the
program from the Acer Empowering Technology program group in Start menu,
or right-click the Windows power icon in the system tray and select Acer ePower
Management.
AC Mode (Adapter mode)
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other
settings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, FireWire
(1394), Wired LAN and Optical Device if supported.
DC Mode (Battery mode)
There are four pre-defined profiles - Entertainment, Presentation, Word Processing, and Battery Life. You can
also define up to three of your own.
To create new power profile
1.
Change power settings as desired.
2.
Click “Save as...” to save to a new power profile.
3.
Name the newly created profile.
4.
Select whether this profile is for Adapter or Battery mode, then click OK.
5.
The new profile will appear in the profile list.
Battery status
For real-time battery life estimates based on current usage, referto the panel on the lower left-hand side of the
window.
22
Chapter 1
For additional options, click “Settings” to:
Set alarms.
Re-load factory defaults.
Select what actions will be taken when the cover is closed or the power button is pressed.
View information about Acer ePower Management.
Acer eDataSecurity Management
(for selected models)
Acer eDataSecurity Management is an encryption utility that protects your files
from being accessed by unauthorized persons. It is conveniently integrated with
Windows Explorer as a shell extension for quick data encryption/decryption and
also supports on-the-fly file encryption for Lotus Notes and Microsoft Outlook.
On first use, the Acer eDataSecurity Management setup wizard will prompt you
to create the Master Password. You will use this password to access the Personal
Secure Disk (PSD). The Master Password may also be used to encrypt/decrypt
files by default.
If you set a different password to encrypt a file, but you forgot the encryption
password, you can use the Master Password to decrypt the file.
Chapter 1
23
24
Chapter 1
Acer eRecovery Management
Acer eRecovery Management is a versatile backup utility. It allows you to create
full or incremental backups, burn the factory default image to optical disc, and
restore from previously created backups or reinstall applications and drivers. By
default, user-created backups are stored to the D:\ drive.
Acer eRecovery Management provides you with:
• Backup:
• Back up factory default to CD/DVD
• Back up drivers and applications to CD/DVD
• Create user backup
• Manage user backups
• Restore:
• Restore system to factory default
• Reinstall applications/drivers
• Restore system from user backup
• Password settings
To use the password protection feature of Acer eRecovery Management to
protect your data, you must first set the Empowering Technology password. To
set the password, refer to the section "Empowering Technology password".
Chapter 1
25
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications, set
BIOS passwords and modify boot options.
Acer eSettings Management also:
26
Chapter 1
• Provides a simple graphical user interface for navigation.
• Prints and saves hardware specifications.
• Lets you set an asset tag for your system.
Windows Mobility Center
Chapter 1
27
The Windows Mobility Center collects key mobile-related system settings in one
easy-to-find place, so you can quickly configure your Acer system to fit the
situation as you change locations, networks or activities. Settings include display
brightness, volume, power plan, wireless networking on/off, external display
settings, synchronization status and presentation settings.
Windows Mobility Center also includes Acer-specific settings like sharing folders
overview/sharing service on or off, Bluetooth Add Device (if applicable), and a
shortcut to the Acer user guide, drivers and utilities.
To launch Windows Mobility Center:
• Use the shortcut key < > + <X>.
• Start Windows Mobility Center from the Control panel.
• Start Windows Mobility Center from the Accessories program group in the
Start menu.
• Launch Windows Mobility Center by right-clicking in the system tray
and select Windows Mobility Center.
28
Chapter 1
Using the System Utilities
NOTE: The system utilities work under Microsoft Windows XP only.
Acer GridVista (dual-display compatible)
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then
select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the
display box and then click the check box Extend my windows desktop onto this monitor. Finally, click
Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start>All Programs and click on Acer GridVista.
You may choose any one of the four display settings indicated below:
Double (verticle), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned indepently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is imple to set up:
1.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2.
Drag and drop each window into the appropriate grid.
3.
Enjoy the convenience of a well-organized desktop.
Chapter 1
29
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Launch Manager
Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access
the Launch Manager by clicking on Start > All Programs > Launch Manager to start the application.
30
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
Intel CPU Penryn
Core logic
Intel 965PM/965GM + ICH8M
CPU package
uFCPGA, Socket P
CPU core voltage
0.944~1.3V
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
6MB
1st level cache control
Always enabled
2st level cache control
Always enabled
Cache scheme control
Fixed in write-back
System Memory
Item
Specification
Memory controller
Intel PM965 / Intel GM965
Memory size
0MB (no on-board memory)
DIMM socket number
2 sockets
Supports memory size per socket
2GB
Supports maximum memory size
4GB
Supports DIMM type
DDR 2 Synchronous DRAM
Supports DIMM Speed
533/667 MHz
Supports DIMM voltage
1.8V and 0.9V
Supports DIMM package
200-pin soDIMM
LAN Interface
Item
Chapter 1
Specification
31
Chipset
ATHEROS_AR8121
Supports LAN protocol
10/100/1000 Ethernet
PCI-E Giga
LAN connector type
RJ45
LAN connector location
Left side
Features
Integrated 10/100/1000 BASE-T transceiver
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
Memory Combinations
Slot 1
32
Slot 2
Total Memory
0MB
256MB
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
0MB
2048MB
2048MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
256MB
2048MB
2304MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
512MB
2048MB
2560MB
1024MB
0MB
1024MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
1024MB
2048MB
3072MB
2048MB
0MB
2048MB
2048MB
256MB
2304MB
2048MB
512MB
2560MB
Chapter 1
2048MB
1024MB
3072MB
2048MB
2048MB
4096MB
LAN Interface
Item
Specification
Chipset
ATHEROS_AR8121
Supports LAN protocol
10/100/1000 Ethernet
PCI-E Giga
LAN connector type
RJ45
LAN connector location
Left side
Features
Integrated 10/100/1000 BASE-T transceiver
Modem Interface
Item
Specification
Data modem data baud rate (bps)
56K
Supports modem protocol
V.92
Modem connector type
RJ11
Modem connector location
Left side
Bluetooth Interface
Item
Specification
Chipset
Built-in ICH8M
Data throughput
723 bps (full speed data rate)
Protocol
Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified).
Interface
USB 2.0
Connector type
USB
Item
Specification
Chipset
Data throughput
Chapter 1
Built-in ICH8M
540 Mbps
33
Protocol
802.11AGN
Interface
PCI
Hard Disk Drive Interface
Item
Specification
Vendor & Model Name
HGST HTS541680J9SA00
WD WD800BEVS-22RST0
Seagate ST9120822AS
Toshiba MK1237GSX
HGST HTS541612J9SA00
WD WD1200BEVS-22RST0
TOSHIBA MK1637GSX
SEAGATE ST9160821AS
HGST HTS541616J9SA00
WD WD1600BEVS-22RST0
Capacity (MB)
80000
Bytes per sector
512
Data heads
2
4 for Toshiba and HGST
4
Drive Format
Disks
1
Spindle speed (RPM)
5400 RPM
Performance Specifications
Buffer size
8M
Interface
SATA
Max. media transfer rate (disk-buffer,
Mbytes/s)
100,150
Data transfer rate (host~buffer, Mbytes/s)
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
DC Power Requirements
Voltage tolerance
5V(DC) +/- 5%
Data transfer rate (host~buffer, Mbytes/s)
34
Chapter 1
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
DC Power Requirements
Voltage tolerance
5V(DC) +/- 5%
DVD-SuperMulti Interface
Item
Vendor & model name
Specification
TOSHIBA 8X TS-L632D
PHILIPS 8X DS-8A1P
HLDS 8X GSA-T20N
Performance Specification
With CD Diskette
Transfer rate (KB/sec)
Sustained:Max 3.6Mbytes/sec
Sustained:Max 10.8Mbytes/sec
Buffer Memory
2MB
Interface
Enhanced IDE(ATAPI) compatible
Applicable disc format
Support disc formats
1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD,
CD-Extra and CD-Plus
2. Reads data in super Audio CD (SACD) Hybrid type
3. Reads standard CD-DA
4. Reads and writes CD-R discs
5. Reads and writes CD-RW andHSRW discs
6. Reads and writes US & US+RW
7. Reads data in each DVD-ROM and DVD-Dual
8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVDRW and DVD+R/RW (Ver1.1)
9.Reads and writes DVD+-R Dual
10.Reads and writes DVD-RAM
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Chapter 1
35
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
Specification
Audio Controller
Realtek ALC889X
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
24 bit stereo full duplex
Compatibility
HD audio Interface; S/PDIF output for PCM or AC-3 content
Sampling rate
1Hz resolution VSR (Variable Sampling Rate)
Internal microphone
Yes
Internal speaker / Quantity
Yes/2(3W speakers)
Supports PnP DMA channel
DMA channel 0
DMA channel 1
Supports PnP IRQ
IRQ10, IRQ11
Video Interface
Item
Chipset
Specification
Acer MXM compatible
Video Memory
Item
Specification
Chipset
Acer MXM compatible
USB Port
Item
Specification
Chipset
Built-in ICH8M
USB Compliancy Level
2
OHCI
USB 1.1 and USB 2.0 Host controller
Number of USB port
4
Location
One on the left side; three on the right side
36
Chapter 1
Serial port function control
Enable/Disable by BIOS Setup
Express Card Interface
Item
Specification
Express card controller
Built-in ICH8M
Supports card type
75mmx54mm(W)x5mm
Number of slots
One
Access location
Left Side
Interface
PCI Express
System Board Major Chips
Item
Controller
Core logic
Intel PM965/GM965 + ICH8M
VGA
Acer MXM compatible
LAN
ATHEROS_AR8121
USB 2.0
Built in ICH8M
CardReader
Jmicro JMB385
MODEM
Foxconn T60M951
Bluetooth
Foxconn T60H928.01
Wireless 802.11 a+b+g
Built-in ICH8-M
Audio
Realtek ALC889X
Keyboard
Item
Specification
Keyboard controller
ITE 8512E
Total number of keypads
88-/89-key
Windows logo key
Yes
Internal & external keyboard work simultaneously
Plug USB keyboard to the USB port directly: Yes
Chapter 1
37
Battery
Item
Vendor & model name
Specification
BATTERY PACK SANYO LI-ION 8 CELL2.4, 4800MAH
BATTRY PACK SONY LI-ION 8CELL2.4, 4800MAH
Battery Type
Li-ion
Pack capacity
4800 mAH
Number of battery cell
8
Package configuration
4 cells in series, 2 series in parallel
Normal voltage
14.8V
Charge voltage
16.8+-0.2V
LCD 16.0" inch
Item
Specification
Vendor & model name
Samsung LTN160AT01-A01
Screen Diagonal (mm)
16.0 inches
Active Area (mm)
353.45(H) x 198.72(V) mm
Display resolution (pixels)
1366x768 WXGA
Pixel Pitch
0.25875 (H) x 0.25875(V) mm
Pixel Arrangement
R.G.B. Vertical Stripe
Display Mode
Normally White
Typical White Luminance (cd/m2)
also called Brightness
300
Luminance Uniformity
N/A
Contrast Ratio
600
Response Time (Optical Rise Time/Fall
Time)msec
8
Nominal Input Voltage VDD
+3.3V
Typical Power Consumption (watt)
4.5W
Weight(g)
550g
Physical Size(mm)
365x214x6.5
Electrical Interface
Dual channel LVDS
38
Chapter 1
Support Color
262,144
Viewing Angle (degree)
Horizontal: Right/Left
65/65
Vertial: Upper/Lower
50/50
Temperature Range(C)
Operating
Storage (shipping)
0 to +50 / -20 to +60
LCD Inverter
Item
Specification
Vendor & model name
TDK
Brightness conditions
N/A
Input voltage (V)
9~20V
Input current (mA)
360mA (max)
Output voltage (V, rms)
710V (1800V for kick off)
Output current (mA, rms)
6.5mA (max)
Output voltage frequency (k Hz)
58 KHz (max)
AC Adaptor
Item
Specification
Input rating
100V AC to 240V AC, 47Hz to 63Hz
Maximum input AC current
1.5A
Inrush current
50A@115VAC
100A@230VAC
Efficiency
85% min. @115VAC input full load
System Power Management
ACPI mode
Chapter 1
Power Management
39
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disc may be power
managed in this state.
Suspend to RAM (S3)
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4)
40
Also called Hibernation Mode. System saves all system states
and data onto the disc prior to power off the whole system.
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Chapter 2
47
Invoking BIOS Setup
The setup function can only be invoked by pressing F2 when Press <F2> to enter Setup message is
prompted on the bottom of screen during POST.
The setup uses a menu driven interface to allow the user to configure their system. The features are divided
into 6 parts as follows:
Information
Display the system informations.
Main
Allows the user to specify standard IBM PC AT system parameters.
Advanced
Provides advanced settings of the system.
Security
Provides security settings of the system.
Boot
Allows the user to specify the boot options.
Exit
Allows the user to save CMOS setting and exit Setup.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
NOTE: Please note that system information is subject to different models.
48
Chapter 2
Information
NOTE: The system information is subject to different models.
Parameter
Description
CPU Type
This field shows the CPU type and speed of the system.
IDE1 Model Name
This field shows the model name of HDD installed on primary IDE master.
IDE1 Serial Number
This field displays the serial number of HDD installed on primary IDE master.
IDE2I Model Name
This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
IDE2 Serial Number
This field shows the serial number of devices installed on secondary IDE master.
System BIOS ver
Displays system BIOS version.
VGA BIOS Ver
This field displays the VGA firmware version of the system.
KBC Ver
This field shows the keyboard
Serial Number
This field displays the serial number of this unit.
Asset Tag Number
This field displays the asset tag number of the system.
Product Name
This field shows product name of the system.
Manufacturer Name
This field displays the manufacturer of this system.
Chapter 2
49
Parameter
UUID Number
Description
This will be visible only when an internal LAN device is presenting.
UUID=32bytes
50
Chapter 2
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
NOTE: The screen above is for your reference only. Actual values may differ.
Chapter 2
51
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed
with 24-hour format.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
System Date
Extended Memory size=Total memory size-1MB
VGA Memory
Shows the VGA memory size. VGA Memory
size=64/128MB
Quiet Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Auto or Both
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Network Boot
Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or Enabled
D2D Recovery
Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
52
Chapter 2
Advanced
The Advanced screen displays advanced settings in BIOS.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
Serial port
Displays the settings of the serial port
Enabled or Disabled
Parallel port
Shows the settings of the parallel port
Enabled or Disabled
Chapter 2
53
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
54
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password is
Shows the setting of the user password.
Clear or Set
Supervisor Password is
Shows the setting of the Supervisor password
Clear or Set
Set User Password
Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
HardDisk Security
Enables or disables primary hard disk security
function.
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The Set
Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
Chapter 2
55
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set
Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The
computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set
Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
56
Chapter 2
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2
57
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
58
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen.
Parameter
Exit Saving Changes
Description
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
59
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
New versions of system programs
New features or options
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
60
1.
Prepare a bootable diskette.
2.
Copy the flash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The flash utility has auto-execution function.
Chapter 2
Remove HDD password Utility
This section provide you with removing HDD password method:
Remove HDD Password:
If you key in wrong HDD password for three time, “HDD password error code” would display on the screen.
See the image below.
If you need to solve HDD password locked problem, you can run unlock6.EXE
1. Key in “unlock6 error code 205”
2. Select “2”
3. Choose one HDD password
Reboot system and key in “R6PI11X” or “MI8N4KK” to HDD user password.
Chapter 2
61
Then the HDD password will be unlocked and will auto into Windows after reboot.
62
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer Aspire 6920 for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
Wrist grounding strap and conductive mat for preventing electrostatic discharge
Small Philips screw driver
hilips screwdriver
Plastic flat head screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
Chapter 3
61
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
62
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Remove the battery pack.
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Chapter 3
63
64
Chapter 3
Removing the Battery Pack
1.
Release the battery.
2.
Slide the battery latch then remove the battery.
Chapter 3
65
Removing the HDD/Memory Module/Wireless LAN Card/TV Tuner Card/
System Fan/Thermal Modules/CPU
Removing the HDD
1.
Remove the six screws fastening the CTO cover
2.
Detach the CTO cover from the notebook.
Removing the Wireless Cover & RAM Module
3.
Remove one screw to release the Wireless cover
4.
Remove the Wireless cover from the notebook.
5.
Pop out the memory module from the DIMM socket then remove it (If the notebook has two memory
modules, then repeat this step).
Removing the Wireless LAN Card/TV Tunder Card and System Fan
66
6.
Pull out the Wireless antenna.
7.
Remove the two screws fastening the wireless LAN card.
Chapter 3
8.
Disconnect the main and auxiliary antennae from the wireless LAN card.
9.
Then take out the wireless LAN card from the main unit.
10. Loose two screws from the TV card.
11. Remove the TV card from the machine.
12. Remove the two screws from the Wireless card.
13. Remove the Wireless card from the machine.
14. Remove HDD module as shown.
15. Unplug power cable from the machine.
16. Remove FAN cable from the machine.
17. Loose the FAN screw.
18. Take out the system fan from the main unit as shown.
Chapter 3
67
Removing the Thermal Modules and the CPU
19. Remove the two screws holding the finger heatsink.
20. Detach the finger heatsink from the main board.
21. Then take out the CPU heatsink from the main board.
22. Use a flat screwdriver to release the CPU lock (Turn counter clock-wise) then remove the CPU carefully.
23. Remove the Express dummy card.
24. Remove the card reader dummy.
68
Chapter 3
Removing the ODD and Dummy cards
25. Remove the screw fastening the optical disk drive module on the bottom.
26. Use a tool to push the optical disk drive module outwards and remove the ODD module
Removing the Hinge cover
27. Remove two hinge cover screws.
28. Then detach the Hinge cover from both side.
Chapter 3
69
Removing the BTCB screws
29. Loose 21 screws from BTCB.
30. Detach Switch cover.
31. Disconnect Media board FFC from the Switch cover
70
Chapter 3
Disassembling the Main Unit
1.
Turn over the keyboard as the image shows.
2.
Disconnect the Keyboard FFC from the main board
3.
Then remove the keyboard from the main unit.
4.
Remove the 18 screws fastening the upper case and the lower case assembly as shown.
5.
Disconnect the FFC from the main board.
6.
Loose two screws from the TPCB.
7.
Disconnect the LCM cable.
8.
Pull out the Power cable.
9.
Pull out the Wireless antenna.
10. Release four TPCB locker then remove the TCB from machine.
Chapter 3
71
Disassembling the LED boards
11. Loose the LED boards four screws.
12. Remove two LED boards from the machine.
13. Loose four LCM hinge screws.
14. Then remove LCM module from the machine.
72
Chapter 3
Remove I/O baord and Main Board.
15. Loose the daughter board screw then remove the daughter board from the machine.
16. Disconnect four cables on the M/B as shown.
17. Loose the M/B screw, remove RJ11 connector from the BTCB.
18. Remove M/B from the BTCB.
Chapter 3
73
19. Disconnect LED/B cable and USB/B FFC.
20. Remove the USB board from BTCB..
21. Loose two Modem card screws.
22. Disconnect Modem card cable.
23. Remove Modem card from the M/B.
Disassembly LCM module
74
1.
Remove six LCM bezel mylar.
2.
Loose 11 LCM bezel screws.
3.
Remove LCM bezel.
4.
Disconnect Inverter cable and Back LED board cable.
5.
Disconnect CCD cable..
6.
Loose four LCD scrws from the hinge.
7.
Remove the LCD panel.
Chapter 3
8.
Remove the Inverter board.
9.
Loose four LCD hinge screws, then remove two hinges from LCD panel.
Chapter 3
75
Disassembling the External Modules
Disassembling the HDD Module
1.
Remove the four screws holding the HDD (hard disk drive) foil; two on each side.
2.
Carefully take out the hard disk drive from the HDD foil.
Disassembling the ODD Module
76
1.
Remove the two screws holding the optical bracket.
2.
Then remove the optical bracket from the optical disk drive.
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 81.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 84
“Undetermined Problems” on page 96
POST detects an error and displayed messages
on screen.
“Error Message List” on page 85
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 84
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 84
“Intermittent Problems” on page 95
“Undetermined Problems” on page 96
Chapter 4
79
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if FDD Test is passed as the program runs to FDD Test.
3.
Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
Numeric keypad
External keyboard
80
Chapter 4
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
“Check the Power Adapter” on page 82
“Check the Battery Pack” on page 83
Chapter 4
81
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
Replace the System board.
If the problem is not corrected, see “Undetermined Problems” on page 96.
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
82
3.
If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4.
If the operational charge does not work, see “Check the Battery Pack” on page 83.
Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the touchpad cables.
2.
Replace the touchpad.
3.
Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4
83
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 96.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
84
Chapter 4
Index of Error Messages
Error Code List
Error Codes
006
Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
<No error code>
Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages
Failure Fixed Disk
FRU/Action in Sequence
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 80.
Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 80.
Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 80.
Keyboard locked - Unlock key switch
Unlock external keyboard
Monitor type does not match CMOS - Run Setup
Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
BIOS ROM
System board
System RAM Failed at offset: nnnn
DIMM
System board
Extended RAM Failed at offset: nnnn
DIMM
System board
System battery is dead - Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Chapter 4
85
Error Message List
Error Messages
Real time clock error
FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration
used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 80.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
86
Chapter 4
Error Message List
No beep Error Messages
No beep, power-on indicator turns off and LCD is
blank.
FRU/Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 81..
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 81..
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors.
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
No beep during POST but system runs correctly.
Ensure every connector is connected tightly and correctly.
System board
Speaker
System board
Chapter 4
87
Phoenix BIOS Beep Codes
Code
Beeps
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
16h
Initialize keyboard controller
1-2-2-3
BIOS ROM checksum
17h
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
Test DRAM refresh
22h
1-3-1-3
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
88
POST Routine Description
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
POST device initialization
Chapter 4
Code
46h
Beeps
2-1-2-3
48h
POST Routine Description
Check ROM copyright notice
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
58h
Set key click if enabled
2-2-3-1
Test for unexpected interrupts
59h
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
Chapter 4
89
Code
Beeps
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
98h
Fixup Multi Processor table
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
POST done- prepare to boot operating system
B4h
90
POST Routine Description
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
Chapter 4
Code
Beeps
D2h
POST Routine Description
Unknown interrupt
Code
Beeps
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
91
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
LCD is too dark
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
LCD brightness cannot be adjusted
Reconnect the LCD connectors.
LCD contrast cannot be adjusted
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Reconnect the LCD connector
Missing pels in characters
LCD inverter ID
Abnormal screen
LCD cable
Wrong color displayed
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 81.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 81.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 81.
Hold and press the power switch for more than 4 seconds.
System board
92
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged
Action in Sequence
See “Check the Battery Pack” on page 83.
Battery pack
System board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
Action in Sequence
In Windows, multimedia programs, no sound
comes from the computer.
Audio driver
Internal speakers make noise or emit no sound.
Speaker
Speaker
System board
System board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation
Action in Sequence
See “Save to Disk (S4)” on page 45.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode and
four short beeps every minute.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
See “Save to Disk (S4)” on page 45.
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “Save to Disk (S4)” on page 45.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby mode
after opening the LCD.
See “Save to Disk (S4)” on page 45.
LCD cover switch
System board
Chapter 4
93
Power Management-Related Symptoms
Symptom / Error
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Action in Sequence
Remove battery pack and let it cool for 2 hours.
Refresh battery (continue use battery until power off, then charge
battery).
Battery pack
System board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Reconnect hard disk/CD-ROM/diskette drives.
System board
USB does not work correctly
System board
Print problems.
Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 96.
94
Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
95
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 81.):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
Non-Acer devices
Printer, mouse, and other external devices
Battery pack
Hard disk drive
DIMM
CD-ROM/Diskette drive Module
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
System board
LCD assembly
96
Chapter 4
Chapter 5
Jumper and Connector Locations
Chapter 5
97
Bottom View
98
Chapter 5
Chapter 5
99
100
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 6920. Refer to this chapter
whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6
99
Aspire6920 Exploded Diagram
100
Chapter 6
Chapter 6
101
102
Chapter 6
Chapter 6
103
CATEGORY
PARTNAME
ACER PART NO.
ACCESSORY
REMOTE CONTROLLER
RT.22700.008
FOMOSA21 RC804V-B EU
REMOTE CONTROLLER
RT.22700.009
FOMOSA21 RC804V-B TC
REMOTE CONTROLLER
RT.22700.010
FOMOSA21 RC804V-B SC
REMOTE CONTROLLER
RT.22700.011
FOMOSA21 RC804V-B EN
WISTRON ACER XPRESS
LC.VIP00.014
CARD PHONE KIT REV 2.0
EXTERNAL ANTENNA SET
25.AAMVN.004
ADAPTER
ADAPTER 65W 3PINS DELTA
AP.06501.013
SADP-65KB DFA YELLOW
1.7X5.5X11 LF LEVEL4
ADAPTER 65W 3PINS LITEON
AP.06503.016
PA-1650-02AC 1.7X5.5X11 LF
LEVEL4
ADAPTER 65W 3PINS HIPRO
AP.0650A.010
HP-OK065B13 1.7X5.5X11 LF
LEVEL4
ADAPTER 90W 3PINS DELTA
AP.09001.013
ADP-90SB BBEA 1.7X5.5X11
LF LEVEL4
ADAPTER 90W LITE-ON PA-
AP.09003.011
1900-24AR BLUE 1.7X5.5X11
LF LEVEL4
ADAPTER 90W HIPRO HP-
AP.0900A.001
OL093B13P BLUE 1.7X5.5X11
LF LEVEL4
BATTERY
104
Chapter 6
BATTERY LI-ION 6CELL
BT.00603.042
SANYO AS-2007B 3S2P
4400MAH
BATTERY LI-ION 6CELL SONY
BT.00604.025
AS-2007B 3S2P 4400MAH
BATTERY LI-ION 6CELL
BT.00605.021
PANASONIC AS-2007B 3S2P
4400MAH
BATTERY LI-ION 6CELL
BT.00607.016
SIMPLO AS-2007B 3S2P
4400MAH
BATTERY LI-ION 8CELL
BT.00803.024
SANYO AS-2007B 4S2P
4800MAH
BATTERY LI-ION 8CELL SONY
BT.00804.020
AS-2007B 4S2P 4800MAH
BATTERY LI-ION 8CELL
BT.00805.011
PANASONIC AS-2007B 4S2P
4800MAH
BATTERY LI-ION 8CELL
BT.00807.015
SIMPLO AS-2007B 4S2P
4800MAH
BOARD
BLUETOOTH BOARD
BT.21100.005
FOXCONN BCM2045 V2
T60H928.11
MAINBOARD AS6920G INTEL
MB.APQ0B.001
PM965 ICH8M ATHEROS
AR8121 LF
Chapter 6
105
MAINBOARD AS6920 INTEL
MB.APD0B.001
GM965 ICH8M ATHEROS
AR8121 LF
106
LED BOARD RIGHT
55.APQ0N.009
LED BOARD LEFT
55.APQ0N.010
TOUCHPAD BUTTON BOARD
55.APQ0N.004
HOTKEY BOARD
55.APQ0N.002
MEDIA BOARD MODULE
55.APQ0N.005
Chapter 6
POWER BUTTON BOARD
55.APQ0N.003
E-KEY BOARD
55.APQ0N.006
USB BOARD W/O TV CABLE
55.APQ0N.008
USB BOARD WITH TV CABLE
55.AP40N.001
I/O BOARD
55.APQ0N.007
VGA CARD nVidia NB8P-GS
55.AKE0N.004
DDRII 512MB 400MHz 32*16
MXM II W/ HDCP (IEC VBIOS)
Chapter 6
107
WIRELESS LAN BOARD
KI.KDN01.001
802.11AGN INTEL 4965AGN
MOW1 MINI PCI
WIRELESS LAN BOARD
KI.KDN01.002
802.11AGN INTEL 4965AGN
MOW2 MINI PCI
WIRELESS LAN BOARD
KI.KDN01.003
802.11AGN INTEL 4965AGN
ROW MINI PCI
MINI WIRELESS BOARD
KI.GLN01.001
802.11ABG MOW1 INTEL
MM872612
MINI WIRELESS BOARD
KI.GLN01.002
802.11 ABG MOW2 INTEL
MM872659
MINI WIRELESS BOARD
KI.GLN01.003
802.11 ABG ROW INTEL
MM874511
MINI WIRELESS LAN BOARD
KI.GLN01.005
802.11BG INTEL 3945BG
TV TUNER MINI CARD
TU.23100.014
AVERMEDIA DVB-T A309 REV
1.0
TV TUNER MINI CARD LITEON
TU.23100.015
DVB-T TT-1260DA REV D
ROBSON BOARD 1GB INTEL
KI.1GB0N.002
NVCPEMWR001G1 LF
FINGER PRINT BOARD
108
55.APQ0N.001
Chapter 6
TOUCHPAD SYNAPTICS TM-
56.APQ0N.001
00372-012
MODEM BOARD FOXCONN
FX.22500.009
MC4Z MDC1.5_3 3.3V
T60M955.00
MODEM BOARD MDC 1.5
FX.22500.022
FOXCONN T60M951.41
(AGERE 1.5_ 3.3V)
MODEM BOARD MDC 1.5
FX.22500.023
FOXCONN T60M951.36
(AGERE 1.5_ 3.3V)
AUSTRALIA APPROVED
CABLE
POWER CORD 3PIN USA
27.AAMVN.001
POWER CORD 3PIN EUR
27.AAMVN.002
POWER CORD 3PIN SOUTH
27.AAMVN.008
AFRICA
POWER CORD 3PIN
27.AAMVN.010
DENMARK
POWER CORD ISRAEL
27.AAMVN.011
POWER CORD 3PIN ITALIAN
27.AAMVN.009
POWER CORD 3PIN UK
27.AAMVN.004
POWER CORD 3PIN SWISS
27.AAMVN.006
POWER CORD AUSTRALIA W/
27.AAMVN.003
LABEL
POWER CORD 3PIN CHINA
27.AAMVN.005
POWER CORD SOUTH
27.AAMVN.007
AFRICA (AIL)
POWER CORD 3PIN USA
Chapter 6
27.AAMVN.001
109
"LCD/CAMERA CABLE 16""
50.APQ0N.012
WUXGA/WXGA"
"LCD/CAMERA CABLE 16""
50.APQ0N.013
WXGA"
DC-IN CABLE
50.APQ0N.011
DC-IN CABLE
50.APD0N.001
MODEM CABLE WITH RJ11
50.APQ0N.010
BLUETOOTH BOARD CABLE
50.APQ0N.009
FINGER PRINT BOARD
50.APQ0N.001
CABLE
HOTKEY BOARD CABLE
110
50.APQ0N.002
Chapter 6
POWER BUTTON BOARD
50.APQ0N.003
CABLE
TOUCH BUTTON BOARD
50.APQ0N.004
CABLE
MEDIA BOARD CABLE
50.APQ0N.005
E-KEY BOARD CABLE
50.APQ0N.006
USB BOARD CABLE
50.APQ0N.007
TOUCHPAD CABLE
50.APQ0N.008
CAMERA
Chapter 6
111
CAMERA 0.3M SUYIN
57.APQ0N.001
CAMERA 0.3M CHICONY
57.APQ0N.002
MINI DUMMY CARD
42.APQ0N.008
SD DUMMY CARD
42.APQ0N.009
BD COMBO BEZEL
42.APQ0N.005
SUPER-MULTI BEZEL
42.APQ0N.004
"LCD COVER 16"" W/
60.APQ0N.005
CASE/COVER/BRACKET
ASSEMBLY
ANTENNA & MIC"
112
"LCD BEZEL 16"""
60.APQ0N.004
LCD BRACKET RIGHT
33.APQ0N.004
Chapter 6
LCD BRACKET LEFT
33.APQ0N.005
UPPER CASE W/ FINGER
60.APQ0N.002
PRINT HOLE
Chapter 6
TOUCHPAD BRACKET
33.APQ0N.001
LOWER CASE
60.APN0N.001
LOWER CASE
60.APD0N.001
LOWER CASE
60.AP40N.001
LOWER CASE
60.APQ0N.001
MIDDLE COVER
42.APQ0N.001
UNILOAD COVER
42.APQ0N.002
113
MPCI COVER
42.APQ0N.003
OPTICAL BRACKET
33.AAMVN.002
KENSINGTON BRACKET
33.APQ0N.006
HINGE COVER ASSEMBLY
42.APQ0N.007
LEFT
HINGE COVER ASSEMBLY
42.APQ0N.006
RIGHT
TBD
114
TBD
Chapter 6
VGA BRACKET TOP
33.APQ0N.003
VGA BRACKET BOTTOM
33.AKE0N.005
CPU INTEL CORE2DUAL
KC.95001.DTP
CPU/PROCESSOR
T9500 PGA 2.6G 6M FSB800
PENRYN
CPU INTEL CORE2DUAL
KC.93001.DTP
T9300 PGA 2.5G 6M FSB800
PENRYN
CPU INTEL CORE2DUAL
KC.83001.DTP
T8300 PGA 2.4G 3M FSB800
PENRYN
CPU INTEL CORE2DUAL
KC.81001.DTP
T8100 PGA 2.1G 3M FSB800
PENRYN
CPU INTEL CORE2DUAL
KC.78001.DTP
T7800 PGA 2.6G 4M FSB800
CPU INTEL CORE2DUAL
KC.77G01.DTP
T7700 PGA 2.4G 4M FSB800
G-0
CPU INTEL CORE2DUAL
KC.75G01.DTP
T7500 PGA 2.2G 4M FSB800
G-0
CPU INTEL CORE2DUAL
KC.73001.DTP
T7300 PGA 2.0G 4M FSB800
CPU INTEL CORE2DUAL
KC.57501.DTP
T5750 PGA 2.0G 2M FSB667
CPU INTEL CORE2DUAL
KC.55501.DTP
T5550 PGA 1.83G 2M FSB667
CPU INTEL CORE2DUAL
KC.54501.DTP
T5450 PGA 1.66G 2M FSB667
Chapter 6
115
CPU INTEL PENTIUM DUAL-
KC.23701.DTP
CORE T2370 PGA 1.73G 1M
FSB533
DVD RW DRIVE
ODD BD COMBO DL 2X SONY
KO.0020E.001
BC-5500A LF W/O BEZEL 1.B1
PATA
ODD BD COMBO DL 2X
KO.00207.001
PANASONIC UJ-120B LF W/O
BEZEL PATA
DVD-RW DRIVE 8X SUPER-
KU.00805.043
MULTI TRAY PIONEER DVRKD08RS LF W/O BEZEL F/
W:1.00 PATA
DVD-RW DRIVE 8X SUPER-
KU.00807.058
MULTI TRAY PANASONIC
TRAY UJ-870BAA-A LF W/O
BEZEL F/W:1.00 PATA
DVD-RW DRIVE 8X SUPER-
KU.00809.011
MULTI TRAY PHILIPS DS-8A1P
LF W/O BEZEL F/W:CA14 PATA
DVD-RW DRIVE 8X SUPER-
KU.0080D.030
MULTI TRAY HLDS GSA-T40N
LF W/O BEZEL PATA
DVD-RW DRIVE 8X SUPER-
KU.0080E.005
MULTI TRAY SONY AD-7560A
LF W/O BEZEL PATA
DVD-RW DRIVE 8X SUPER-
KU.00801.020
MULTI TRAY TOSHIBA TSL632H LF W/O BEZEL PATA
FAN
FAN
23.APQ0N.001
HEATSINK
116
Chapter 6
CPU HEATSINK FOR 965GM
60.APD0N.002
CPU HEATSINK FOR 965PM
60.APQ0N.003
CPU HEATSINK FINGER
33.APD0N.001
CPU HEATSINK FINGER
33.APQ0N.002
HDD 120GB SATA 5400RPM
KH.12001.032
HDD/HARD DISK DRIVER
SEAGATE ST9120817AS
CORSAIR LF F/W:3.AAA
HDD 120GB 5400RPM SATA
KH.12004.007
TOSHIBA MK1246GSX LEO BS
I LF F/W:LB213J
HDD 120GB 5400RPM SATA II
KH.12007.014
HGST HTS542512K9SA00
BRONCO-B LF F/W:C31P
HDD 120GB 5400RPM SATA
KH.12008.019
WD WD1200BEVS-22UST0
ML125 LF F/W:01.01A01
HDD 160GB 5400RPM SATA
KH.16001.029
SEAGATE ST9160827AS
CORSAIR LF F/W:3.AAA
Chapter 6
117
HDD 160GB 5400RPM SATA
KH.16004.002
TOSHIBA MK1646GSX LEO BS
LF F/W:LB113J
HDD 160GB 5400RPM SATA II
KH.16007.016
HGST HTS542516K9SA00
BRONCO-B LF F/W:C31P
HDD 160GB 5400RPM SATA
KH.16008.022
WD WD1600BEVT-22ZCTO
ML160 LF F/W:11.01A11
HDD 160GB 5400RPM SATA
KH.25001.011
SEAGATE ST9250827AS
CORSAIR LF F/W:3.AAA
HDD 160GB 5400RPM SATA
KH.25004.001
TOSHIBA MK2546GSX LEO BS
LF F/W:LB013J
HDD 250GB 5400RPM SATA II
KH.25007.011
HGST HTS542525K9SA00 LF
F/W:C31P
HDD 250GB 5400RPM SATA
KH.25008.018
WD WD2500BEVS-22UST0
ML125 LFF/W:01.01A01
HDD 320GB 5400RPM SATA
KH.32008.013
WD WD3200BEVT-22ZCT0
ML160 LF F/W:11.01A11
INVERTER
INVERTER BOARD TDK-
19.APQ0N.001
TBD484NR
KEYBOARD
KEYBOARD 15_16KB-FV1
KB.INT00.261
88KS BLACK US
INTERNATIONAL (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.264
89KS BLACK TURKISH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.265
88KS BLACK THAILAND
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.266
89KS BLACK SWISS/G
(GLOSSY)
118
Chapter 6
KEYBOARD 15_16KB-FV1
KB.INT00.267
89KS BLACK SWEDISH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.268
89KS BLACK SPANISH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.269
89KS BLACK SLOVAK
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.270
89KS BLACK SLO/CRO
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.271
88KS BLACK RUSSIAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.272
89KS BLACK PORTUGUESE
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.273
89KS BLACK POLISH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.274
89KS BLACK NORWEGIAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.276
88KS BLACK KOREAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.277
88KS BLACK JAPANESE
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.278
89KS BLACK ITALIAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.281
89KS BLACK HUNGARIAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.282
88KS BLACK GREEK
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.283
89KS BLACK GERMAN
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.284
89KS BLACK FRENCH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.286
89KS BLACK DUTCH
(GLOSSY)
Chapter 6
119
KEYBOARD 15_16KB-FV1
KB.INT00.287
89KS BLACK DANISH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.288
89KS BLACK CZECH
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.289
88KS BLACK TRADITIONAL
CHINESE (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.290
89KS BLACK CANADIAN
FRENCH (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.291
89KS BLACK BRAZILIAN
PORTUGUESE (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.292
89KS BLACK BELGIUM
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.293
88KS BLACK ARABIC/
ENGLISH (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.294
89KS BLACK ARABIC/
FRENCH (GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.295
89KS BLACK NORDIC
(GLOSSY)
KEYBOARD 15_16KB-FV1
KB.INT00.296
89KS BLACK ENGLISH/
CANADIAN FRENCH
(GLOSSY)
LCD
"LCD 16"" WXGA SAMSUNG
LK.16006.001
LTN160AT01-A01 GLARE LF
220NIT 8MS 600:1 16:9"
"LCD 16"" WUXGA SAMSUNG
LK.16006.002
LTN160HT01-A01 GLARE LF
220NIT 8MS 600:1 16:9"
MEMORY
SODIMM 512MB DDRII667
KN.51203.032
NANYA NT512T64UH8B0FN3C LF
120
Chapter 6
SODIMM 512MB DDRII667
KN.5120G.024
HYNIX HYMP164S64CP6-Y5
LF
SODIMM 1GB DDRII667
KN.1GB03.014
NANYA NT1GT64U8HB0BN-3C
LF
SODIMM 1GB DDRII667 HYNIX
KN.1GB0G.012
HYMP112S64CP6-Y5 LF
SODIMM 1GB DDRII667
KN.1GB0B.016
SAMSUNG M470T2864QZ3CE6 LF
SODIMM DDRII 667 2GB
KN.2GB0G.004
HYNIX HYMP125S64CP8-Y5
LF
SODIMM DDRII 667 2GB
KN.2GB0B.003
SAMSUNG M470T5663QZ3CE6 LF
MISCELLANEOUS
LCD CHUSION
47.APQ0N.001
VGA BOARD INSULATOR
47.AKE0N.002
HDD INSULATOR
42.AAMVN.005
SPEAKER SET W/ SUB-
23.APQ0N.002
SPEAKER
WOOFER
SCREW
SCREW M2.5X0.45
86.APQ0N.001
SCREW-I25030M (4.0DX0.8T)-
86.APQ0N.002
BK-PATCH
Chapter 6
SCREW
86.AAMVN.001
SCREW BNI PAT
86.TLT0N.002
121
SCREW I M2 6MM M 4.5MM
86.APQ0N.004
0.8MM PHIL BK PATCH
SCREW I M2.5 2.5MM MACH
86.APQ0N.005
4.5MM 0.8MM CROSS BNI
PATCH
122
Chapter 6