Download DEUTSCH ENGLISH digitalSTROM / SW-ZWS200-F SW-ZWS200
Transcript
aizo a g www.aizo.com DEUTSCH Funktion und Verwendungszweck Der schwarze Zwischenstecker (Gruppe wahlweise gelb, grau ...) ist für den steckb aren Anschluss großer Lampenlasten oder großer elektrischer Verbraucher vorgesehen. Angeschlossene Verbraucher können über die 230V-Leitung via digitalSTROM Kommandos gesteuert werden. Es steht ein Taster an der Frontseite zur Verfügung, mit dem der Verbraucher auch ohne digitalSTROM geschaltet werden kann. Weiterführende Informationen zu digitalSTROM, wie z. B. d as Aufrufen von Lichtstimmungen, Bedienen von mehreren Stellen, Zeitsteuerungen usw. siehe digitalSTROM-Handbücher: www.aizo.com/support digita lSTRO M SW-ZWS200-F / SW-ZWS200-J SW-ZWS200-F Zwischenstecker (schw arz) Typ F Schutzkonta kt SW-ZWS200-J Zwischenstecker (schw arz) Typ J Schweiz Bedienanleitung EN 61058 EN 50428 A0818D024V005 F Wichtig e Hinweise: Das G erät d arf nur in trockenen und geschlossenen Räumen betrieben und nicht zu direkt oder indirekt gesundheits- oder lebenssichernden Zwecken benutzt werden oder zu Zwecken, bei denen ein Ausfall des G erätes zu G efahren für Menschen, Tiere oder Sachwerte führen kann. J 108,0 G erät nicht im Hausmüll entsorgen. Elektronische G eräte sind entsprechend der Richtlinie über Elektro- und Elektronik-Altgeräte über die örtlichen Sammelstellen zu entsorgen. Nur zum G ebrauch in Räumen. 59,0 PE N L 230 VAC (mm) Inb etrie bnahme: Der Betrieb erfolgt in einer beliebigen Steckdose. Der zu steuernde Verbraucher wird in die Steckdose des Zwischensteckers gesteckt. N ach dem Einstecken in die Steckdose meldet sich der Zwischenstecker automatisch am digitalSTROM-Meter im Stromkreisverteiler an. Anschließend ist d as G erät sofort betriebsbereit und kann über digitalSTROM-Kommandos gesteuert werden. dSM B 16 A dSM L N Steckdose 230 V Stecker 230 V L Die Betriebsart kann mittels Installationssoftware des digitalSTROM-Servers a ber auch durch Verwendung des Tasters ge ändert werden. L 1 N L1' L1‘ K1 Betrie bsarten: Der Zwischenstecker verfügt über drei Betriebsarten: Scha lten - Ein angeschlossenes G erät wird über übliche Stimmungsaufrufe ein-/ ausgeschaltet . Sp aren - Ausg ang schaltet nur bei Stimmungen „G ehen“, „Schlafen“, „Tiefschlaf“ a b, z. B. zum Abschalten von G eräten mit Standby-Verbrauch bei Abwesenheit. Wischen - G erät schaltet bei Stimmungen „Aus“ und „Standby“ kurz a b und wieder ein, z. B., um TV-G erät/Kaffeemaschine ... in Standby zu versetzen. Zudem kann die Gruppenzugehörigkeit (Farbe) des Zwischensteckers ge ändert werden sowie die Wirkung des Tastereing angs. L1‘ LED+Taster N Steckdose 230 V Dimmb are Leuchtmittel Dimmb are Leuchtmittel können mit diesem Produkt ausschließlich geschaltet, a ber nicht gedimmt werden. Funktionszuordnung im Auslieferzustand: eingestellte Farbgruppe ...................................................................... schwarz (Joker) Ausg ang ................................................................................................... Sp arbetrieb Drucktaster ............................................................................................... G erätetaster Netzunterbrechung: Der Zwischenstecker speichert den Zustand des Ausg angs, sob ald er für mindestens 5 Sekunden unverändert vorliegt. N ach einer Netzunterbrechung wird der gespeicherte Zustand am Ausg ang wieder hergestellt. Üb erl ast: Der Zwischenstecker erkennt Überlasten und schaltet den Ausg ang a b. Ein Rücksetzen erfolgt mit dem nächsten Szenenaufruf (Kommando über digitalSTROM oder durch Taster-Bedienung), vorausgesetzt es liegt keine weitere Überlastung vor. Üb ertemp era tur: Der Ausg ang schaltet a b, sob ald längere Zeit eine thermische Überlastung vorliegt. N ach der Abkühlphase wird er automatisch wieder eingeschaltet. Sta tus-Anzeig e (LED): Zustand: Die LED gibt Rückmeldung über die letzte Aktion am G eräte ausg ang. Stimmung aktiv = LED 100 % an, Stimmung nicht aktiv = LED stark gedimmt. Während der Änderung von Stimmungen blinkt die LED. Beim Einstellen von Stimmungen im Raum (Programmiermodus) blinkt die LED 2-mal, wenn der Zwischenstecker selektiert wird. De e p Off: Im Raumzustand „Deep Off“ ist die LED ausgeschaltet. Anmeldung: Während der Anmeldung an einem digitalSTROM-System blinkt die LED schnell. Fehlerzuständ e: 1 x Blinken – 1 x Pause .............................. Übertemperatur 4 x Blinken – 1 x Pause .............................. Überlast 5 x Blinken – 1 x Pause .............................. Überlast und Übertemperatur Loka le Be dienung: Auf der Frontseite befindet sich ein Taster (kombiniert mit der Status-LED) zur lokalen Bedienung. Kurzer Tipp ...................................................................... ein-/ ausschalten G edrückt Halten im ausgeschalteten Zustand ......... nach 1 Sek.: Raum Farbgruppe ausschalten nur bei Einstellung gelb: nach 2 Sek.: Raum Standby nach 3 Sek.: Raum Deep Off Doppel-Tipp ..................................................................... Aufrufen der Stimmung 2 Dreifach-Tipp ................................................................... Aufrufen der Stimmung 3 Vierfach-Tipp ................................................................... Aufrufen der Stimmung 4 Loka le Parameter-Konfigura tion: Parameter 1 ............................................. Ausg ang (Schalterbetrieb/Sp arbetrieb/Wischerbetrieb) Parameter 2 ............................................. Farbgruppe (gelb, grau, blau, cyan, ma genta, schwarz) Parameter 3 .............................................. Tasterfunktion (G erätetaster/Bereichstaster/Raumtaster) Vor einer Änd erung dieser Parameter unb e dingt die weiterführend en Informa tionen im digita lSTRO M-Insta ll a tionshand buch b e a chten: www. a izo.com/sup port Be dienung loka le Parameter-Konfigura tion: Kurz-kurz-lang bis Ausg ang/LED blinkt ............................... Aktivierung Doppel-Tipp ............................................................................ Wechseln zwischen Parametern Kurzer Tipp ............................................................................. Ändern des ausgewählten Parameters N ach 30 Sek. ohne Bedienung ........................................... Automatischer Abbruch ohne Speichern G edrückt halten (ca. 3 Sek.) bei Aktivierung ................... Speichern und Verlassen Parameter im Deta il: Parameter 1: Schalten: LED blinkt; Wischen: LED an, blitzt kurz aus; Sp aren: LED dimmt aus Parameter 2: LED wechselt die Farbe; Anzeigenfolge: Regenbogen... ausgewählte Farbe … Regenbogen … ausgewählte Farbe … Parameter 3: G erätetaster: LED leuchtet; Raumtaster: LED blinkt 5x; Bereichstaster 1 (oder 2, 3, 4): LED blinkt 1x (oder 2x, 3x, 4x) G ew ährleistung: aizo a g gewährt auf dieses Produkt eine mängelfreie Funktionalität gemäss Spezifikation während einer Frist von 24 Monaten a b Lieferung durch aizo a g. Durch Öffnen des G erätes, sonstige G eräteeingriffe oder unkorrekte Installation/Konfiguration erlischt die G ewährleistung. Technische Da ten: Schaltprinzip ..................................................................................... Elektromech., Relais DE2a-L2-24D Ohmsche Verbraucher ................................................................... ° 2300 W (10A) Induktive /Ka p azitive Verbraucher ................................................ ° 700 W (3A)* Nenneing angssp annung/Frequenz ............................................. 230 V AC/50 Hz Leistungsaufnahme .......................................................................... 0,4 W Schutzart (trockene Räume) .......................................................... IP20 EN 60529 Zulässige Umgebungstemperatur (Betrieb) .............................. 0 °C ... +35 °C Datenübertra gung via 230 V AC Netz ........................................ digitalSTROM-Protokoll V1.0 * Nennbetrieb. Einschaltströme der Last be achten. Technische Änderungen vorbehalten. Neueste Informationen finden Sie auf unserer Webseite. Dok. Nr. A0818D024V005 / 2012-12-01 aizo a g www.aizo.com EN GLISH Function and Intend e d Use The black plug a d a pter (optionally yellow, grey… group ) is designed for plugging in large lamp loa ds or large electrical loa ds. Connected loa ds can be controlled over the 230 V wiring via digitalSTROM commands. A push-button switch is availa ble on the front side with which the loa d can be switched O N/ OFF without using digitalSTROM. For further user information a bout digitalSTROM, e.g. how to select light scenes, operate from multiple locations, activate timer controls etc., ple ase refer to the digitalSTROM user manual: www.aizo.com/support digita lSTRO M SW-ZWS200-F / SW-ZWS200-J SW-ZWS200-F plug a d a pter (bl a ck) typ e F thre e-wire socket SW-ZWS200-J plug a d a pter (bl a ck) Typ e J Switzerl and O perating Instructions EN 61058 EN 50428 F Important informa tion: The device may only be operated in dry, closed rooms and must not be used directly or indirectly for he alth or life-saving purposes or for purposes where a device failure could end anger people, animals or property. J 108,0 The device must not be disposed of in household waste. Electronic equipment must be disposed of via the local collection points in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). Only for indoor use. 59,0 PE N L 230 VAC Commissioning: The device can be placed in any socket. The loa d to be controlled is plugged into the power socket of the plug a d a pter. After be plugged into the socket, the plug a d a pter is automatically registered at the digitalSTROM meter in the power distribution p anel. The device is then immediately re a dy for operation and can be controlled via digitalSTROM commands. dSM L N power socket 230 V plug 230 V L LED+switch Mod es of op era tion: The plug a d a pter has three operating modes: Switch - a connected device can be switched O N/ OFF over the customary scene requests. Economy - output switches only by scenes "Le ave", "Sleep", "Deep Off", for example, switching off devices with standby loa ds in your a bsence. Wip e - device briefly switches on/off by " OFF" and "Standby" scenes, for example, to place TV / coffee machine into standby mode. In a ddition, group membership (colour) of the plug a d a pter can be changed as well as the effect of the push-button input. The operating mode can be changed by the digitalSTROM server's installation software as well as manually by using the push-button. L 1 N L1' L1‘ K1 Error sta tuses: 1 x flash - 1 x p ause: .................................. overtemperature 4 x flash - 1 x p ause: .................................. overloa d 5 x flash - 1 x p ause: .................................. overloa d & overtemperature Loc a l op era tion: On the front side there is a push-button switch (combined with status LED) for local operation. Short ta p .............................................................................. switch O N/ OFF Keep pressed when switched OFF ................................. after 1 sec: Turn room colour group OFF only with yellow setting: after 2 sec: room standby after 3 sec: room Deep Off Double ta p .......................................................................... request scene 2 Triple ta p ............................................................................. request scene 3 Qua druple ta p ................................................................... request scene 4 Loc a l p arameter configura tion: Parameter 1 ..................... output (switch, economy, wipe operation) Parameter 2 ..................... colour group (yellow, gray, blue, cyan, ma genta, black) Parameter 3 ..................... push-button function (device push-button / zone switch / room switch) (mm) dSM B 16 A Sta tus Indic a tor (LED): Sta tus: The LED provides feedb ack on the last action performed on the device's output. Scene active = LED 100 % O N, scene inactive = LED strongly dimmed. The LED flashes during scene changes. When setting the room mood (programming mode), the LED flashes 2 times when the plug a d a pter is selected. De e p Off: The LED is OFF in "Deep Off" room status. Re gistra tion: The LED flashes quickly while registering with a digitalSTROM system. L1‘ Dimma ble l amps Dimma ble lamps can only be switched O N/ OFF with this product, not dimmed. N power socket 230 V Function ma p ping as d elivere d from the f a ctory: Current colour group ..................................................... black (Joker) Output ............................................................................... economy mode Push button switch ......................................................... device push-button Power f a ilure: The plug a d a pter saves the output status if it has been unchanged for at le ast 5 seconds. After a power failure, the saved output status is restored. Overlo a d: The plug a d a pter detects overloa ds and switches OFF the output. A reset is performed the next time a scene is selected (command via digitalSTROM or push-button operation), provided the overloa d no longer exists. Overtemp era ture: The output is switched OFF if a thermal overloa d exists for a long period of time. It is automatically switched O N after the cool-down phase. Subject to technical changes. Latest information can be found on our website. Doc. No. A0818D024V005 / 2012-12-01 Prior to changing these p arameters, ple ase refer to the a d ditiona l informa tion in the digita lSTRO M Insta ll a tion Guid e: www. a izo.com/sup port Loc a l p arameter configura tion: Short-short-long until output / LED flashes ............................. activation Double ta p ................................................................................... switch between p arameters Short ta p ....................................................................................... change the selected p arameters After 30 seconds without activity ............................................. automatic a bort without saving Keep pressed (a bout 3 seconds) while activating .............. save and exit Parameter d eta ils: Parameter 1: Switch: LED flashes, wipe: LED O N, flash briefly OFF; economy: LED dims OFF Parameter 2: LED changes colour, display order: rainbow ... selected colour ... rainbow ... selected colour ... Parameter 3: Device push-button: LED glows, room switch: LED flashes 5x; zone switch 1 (or 2, 3, 4): LED flashes 1x (or 2x, 3x, 4x) Guarante e: aizo a g guarantees fault-free operation of this device in accord ance with the specifications for 24 months from delivery by aizo a g. O pening the device, tampering with the device or incorrect installation / configuration invalid ates the guarantee. Technic a l d a ta: Switching principle ..................................................................... electromechanic, Relay DE2a-L2-24D Resistive loa ds ............................................................................ ° 2300 W (10A) Inductive / ca p acitive loa ds ..................................................... ° 700 W (3A)* Rated input volta ge / frequency ............................................. 230 V AC / 50 Hz Power consumption .................................................................... 0.4 W Protection class (dry rooms) ..................................................... IP20 EN 60529 Permissible ambient temperature (operation) ..................... 0 °C ... +35 °C Data transmission via 230 V AC mains .................................. digitalSTROM protocol V1.0 * Nominal operation. Check the starting current loa d. aizo a g www.aizo.com ITALIAN O Funzione e impie go previsto L'a d attatore nero (a scelta gruppo giallo, grigio ... ) è cre ato a ppositamente in funzione della connessione a spina di grandi carichi di lamp a de o di grandi utenze elettriche. Le utenze colleg ate possono venire accese o spente attraverso il cavo d a 230 V mediante i comandi digitalSTROM. L'a d attatore dispone sulla p arte frontale di un pulsante con cui l'utenza può essere attivata anche senza digitalSTROM. Ulteriori informazioni su digitalSTROM, come a d es. la selezione dello scenario luci, la commutazione di più elementi di controllo, l'attivazione di comandi temporizzati ecc. sono reperibili nei manuali utente digitalSTROM: www.aizo.com/support. digita lSTRO M SW-ZWS200-F / SW-ZWS200-J SW-ZWS200-F Ad a tta tore (nero) Tipo F Schuko SW-ZWS200-J Ad a tta tore (nero) Tipo J Svizzera Istruzioni d'uso EN 61058 EN 50428 F Indic azioni importanti Il dispositivo deve essere attivato solo in ambienti chiusi e asciutti e non deve essere utilizzato né direttamente né indirettamente per la protezione della vita o della salute o per qualsiasi altra finalità per cui un guasto del dispositivo stesso possa determinare un pericolo per persone, animali o beni materiali. J 108,0 Non smaltire l'a pp arecchio tra i rifiuti domestici. Le a pp arecchiature elettroniche devono essere smaltite nei punti di raccolta locali nel rispetto delle direttive sugli a pp arecchi elettrici ed elettronici. Ad atto solo a uso interno. 59,0 PE N L 230 VAC (mm) Messa in funzione Il funzionamento avviene mediante una presa. L'utente d a gestire viene inserito nella presa dell'a d attatore. Dopo l'inserimento l'a d attatore si registra automaticamente rispetto al misuratore digitalSTROM nel qua dro di distribuzione elettrica. Dopo di che, il dispositivo è pronto al funzionamento e può essere controllato attraverso i comandi digitalSTROM. dSM B 16 A dSM L N Presa di corrente 230 V Spina 230 V L L 1 N L1' L1‘ K1 Mod a lità di funzionamento L'a d attatore dispone di tre mod alità di funzionamento: Accensione – Un dispositivo viene acceso/spento attraverso la normale selezione dello scenario Risp armio – L'uscita si accende solo negli ambienti “Funzionamento”, “Riposo”, “Letargo”, p.es. per spegnere i dispositivi con consumo in standby in caso di assenza. Pulizi a - L'a pp arecchio si spegne e si riaccende brevemente in caso di scenari “off” e “standby”, p.es. per mettere in standby TV, macchina del caffè ecc. Inoltre è possibile modificare l'a pp artenenza ai gruppi (colore) dell'a d attatore o l'effetto dell'ingresso del pulsante. La mod alità di funzionamento può essere modificata mediante il software di installazione del server digitalSTROM e utilizzando il pulsante. L1‘ LED+pulsante N Presa di corrente 230 V Lamp a d e dimmera bili Con questo prodotto le lamp a de dimmera bili possono essere attivate, ma non dimmerate. Le specifiche sono soggette a modifiche. Le ultime informazioni sono disponibili sul nostro sito web. Doc. n. A0818D024V005 / 2012-12-01 aizo a g www.aizo.com Asse gnazione funzioni condizioni di fornitura: Gruppo colore impostato ............................................. Nero (jolly) Uscita ................................................................................ Risp armio Pulsante a pressione ..................................................... Pulsante a pp arecchio Interruzione d ell'a limentazione di rete L'a d attatore memorizza lo stato dell'uscita nel momento in cui questo rimane invariato per almeno 5 secondi. Dopo un'interruzione dell'alimentazione di rete, lo stato dell'uscita memorizzato sarà ripristinato. Sovra cc arico L'a d attatore rileva eventuali sovraccarichi e disattiva la propria uscita. Il ripristino avviene con la successiva selezione di scenario (comando attraverso digitalSTROM o tramite controllo locale), purché non sussista nessun altro sovraccarico. Sovra temp era tura L'uscita si disattiva nel momento in cui si verifica un sovraccarico termico. Dopo la fase di raffredd amento, si riattiva automaticamente. FRANCAIS Fonction et doma ine d'a p plic a tion La prise intermédiaire noire (groupe au choix, jaune, gris…..) est prévu pour le raccordement p ar prise de plus grandes charges de lampes ou de grands consommateurs électriques. Les consommateurs connectés peuvent être commandés p ar la conduite 230V via des commandes digitalSTROM. Une touche est disponible sur la face frontale avec la quelle le consommateur peut aussi être allumé sans digitalSTROM. Vous trouverez de plus amples informations pour l'utilisateur du digitalSTROM, comme p ar exemple l'a ppel d'ambiances de couleurs, la commutation de différents points, une commande temporelle etc. d ans le manuel digitalSTROM : www.aizo.com/support digita lSTRO M SW-ZWS200-F / SW-ZWS200-J SW-ZWS200-F Prise intermé di a ire (noire) typ e F Conta ct d e protection SW-ZWS200-J Prise intermé di a ire (noire) Typ e J Suisse EN 61058 EN 50428 Mode d'emploi F Remarques importantes : L'a pp areil ne peut être exploité que d ans des locaux secs et non à des fins (directes ou indirectes) présentant des risques pour la santé ou la vie ni à des fins pour lesquelles une p anne de l'a pp areil peut présenter un d anger pour les personnes, les animaux ou les biens matériels. J 108,0 Ne p as éliminer l'a pp areil avec les déchets ména gers. Les a pp areils électroniques doivent être éliminés selon les directives concernant les vieux a pp areils électriques et électroniques d ans les points de collecte locaux. À utiliser uniquement d ans les pièces. 59,0 PE N L 230 VAC (mm) Mise en service : L'exploitation est ré alisée d ans la prise souhaitée. Le consommateur à commander est placé d ans la prise intermédiaire. Après branchement d ans la prise, la prise intermédiaire se signale automatiquement sur le digitalSTROM-Meter d ans le distributeur du circuit électrique. Puis l'a pp areil est immédiatement prêt à l'emploi et peut être commandé via la commande digitalSTROM. dSM B 16 A dSM L N Price 230 V Fiche 230 V L LED+Touche L 1 N L1' L1‘ K1 L1‘ N Price 230 V Ag ent lumineux à vari a tion d'intensité L'a gent lumineux à intensité varia ble peut être exclusivement mis en servie avec cet a pp areil mais sans variation d'intensité. Sous réserve de modifications techniques. Vous trouverez les dernières informations disponibles sur notre site Web. Doc. No. A0818D024V005 / 2012-12-01 Mod es d e fonction : La prise intermédiaire dispose de trois modes de fonction : Mise en service – un a pp areil branché est allumé / éteint via les a ppels ha bituels d'ambiances. Économiser – la sortie est coupée uniquement lors des ambiances „p artir“, „dormir“, „sommeil profond“ p ar exemple pour arrêter des a pp areils avec consommation Standby lors d'une a bsence. Ba l ayer – l'a pp areil s'arrête brièvement lors des ambiances „éteint“ et „Standby“ et redémarre, p ar exemple pour placer un téléviseur/machine à café Standby. De plus, l'a pp artenance au groupe (couleur) de la prise intermédiaire peut être modifiée. Indic azione di sta to (LED) Sta to: Il LED fornisce il riscontro dell'ultima azione effettuata sull'uscita. LED 100 % = scenario ambiente acceso, LED molto b asso = scenario ambiente spento Durante la variazione degli scenari ambiente il LED lampeggia. Durante la programmazione degli scenari ambiente (mod alità di programmazione) il LED lampeggia due volte quando l'a d attatore viene selezionato. De e p off: in condizione ambiente di deep off il LED è spento. Re gistrazione: durante la registrazione in un sistema digitalSTROM il LED lampeggia velocemente. Condizioni di errore 1 lampeggiamento – 1 p ausa ..................... Sovratemperatura 4 lampeggiamenti – 1 p ausa ...................... Sovraccarico 5 lampeggiamenti – 1 p ausa ...................... Sovraccarico e sovratemperatura Controllo loc a le Sulla p arte frontale si trova un pulsante (combinato con il LED di stato) per i comandi locali. Breve tocco ................................................................ Accendere /spegnere Tenendo premuto d a spento .................................. dopo 1s: spegnimento gruppo luce ambiente solo in caso di impostazione giallo: dopo 2 s: Mod alità standby ambiente dopo 3 s: Deep off ambiente Doppio tocco ............................................................. Selezione scenario ambiente 2 Triplo tocco ................................................................ Selezione scenario ambiente 3 Qua druplo tocco ....................................................... Selezione scenario ambiente 4 Configurazione p arametri loc a le Parametro 1 .................. Uscita (funzione commutazione /funzione risp armio/funzione lava ggio) Parametro 2 .................. Gruppo colore (giallo, grigio, blu, azzurro, ma genta, nero) Parametro 3 .................. Funzione pulsanti (pulsante a pp arecchio/pulsante settore /pulsante ambiente) Prima di modific are questi p arametri, le gg ere con a ttenzione le informazioni riporta te nel manua le di insta ll azione o di utilizzo digita lSTRO M: www. a izo.com/sup port Uso configurazione p arametri loc a le Breve-breve-lungo finché l'uscita /LED lampeggia .... Attivazione Doppio tocco ................................................................... Passa ggio tra p arametri Breve tocco ....................................................................... Modifica del p arametro selezionato Dopo 30 s senza comandi ............................................ Interruzione automatica senza salvata ggio Tenendo premuto (circa 3 s) all'attivazione .............. Salvare e a bb andonare Detta gli p arametri Parametro 1: Accensione. il LED lampeggia; Pulizia: LED acceso, si spegne brevemente; Risp armio: LED riduce la luminosità Parametro 2: Il LED cambia colore; sequenza avvisi: arcob aleno ... colore scelto … arcob aleno … colore scelto … Parametro 3: Pulsante a pp arecchio: il LED si accende; pulsante ambiente: il LED lampeggia 5 volte; Pulsante settore 1 (oppure 2, 3, 4): il LED lampeggia una volta (oppure 2, 3, 4 volte) G aranzi a aizo g arantisce per questo prodotto un perfetto funzionamento, conforme alle specifiche tecniche, per un periodo di 24 mesi d al momento della consegna d a p arte di aizo a g. L'a pertura del dispositivo, altri interventi su di esso o un'installazione /configurazione scorretta annullano la validità della g aranzia. Da ti tecnici Principio accensione .................................................................. Relè elettromeccanico DE2a-L2-24D Consumatore ohmico ................................................................. ° 撰 2300 W (10A) Consumatore induttivo/ca p acitivo ........................................... ° 700 W (3A)* Tensione nominale di entrata /frequenza ............................... 230 V AC/50 Hz Potenza assorbita ... 0,4 W C ategoria di protezione (ambienti asciutti) ........................... IP20 EN 60529 Temp. ambiente ammessa (funzionamento) .. ....................... 0°C ... +35°C Trasmissione dei d ati attraverso rete 230 V AC ................... Protocollo digitalSTROM V1.0 * Prestare attenzione alle correnti nominali di entrata del carico. Afficha g e du sta tut (LED) : Éta t : la LED donne une réponse concernant la dernière action sur la sortie de l'a pp areil. Ambiance active = LED 100 % active, ambiance inactive = LED fortement réduite. Pend ant la modification d'ambiances, la LED clignote. Lors du régla ge d'ambiances d ans la pièce (mode programmation) la LED clignote 2 fois lorsque la prise intermédiaire est sélectionnée. De e p Off: d ans l'état de pièce „Deep Off“ la LED est éteinte Enre gistrement : pend ant l'enregistrement sur un système digitalSTROM, la LED clignote ra pidement. Éta ts d e d éf aut : 1 x clignotement – 1 x p ause ................... surchauffe 4 x clignotement – 1 x p ause ................... surcharge 5 x clignotement – 1 x p ause ................... surcharge et surchauffe Command e loc a le : Une touche se trouve sur la face frontale (combinée avec le statut LED) pour la commande locale. Courte pression ............................................... allumer/ éteint Maintenir enfoncé d ans l'état éteint ........... a près 1s: éteindre sur le groupe de couleurs pièce jaune uniquement lors du régla ge : a près 2s: pièce en Standby a près 3s: pièce Deep Off Double pression .............................................. Appel d'ambiance 2 Triple pression ................................................. Appel d'ambiance 3 Qua druple pression ....................................... Appel d'ambiance 4 Configura tion loc a le d es p aramètres : Paramètre 1 .......................... sortie (mode commutation/mode économique /mode b alaya ge) Paramètre 2 .......................... groupe de couleurs (jaune, gris, bleu, cyan, ma genta, noir) Paramètre 3 .......................... fonction des touches (touche a pp areil/touche zone /touche pièce) Avant d e modifier ces p aramètres, resp ecter a bsolument les informa tions sup plémenta ires du manuel d'insta ll a tion du digita lSTRO M : www. a izo.com/sup port Command e d e l a configura tion loc a le d es p aramètres : Court-court-long jusqu'à la sortie /LED clignote ......... Activation Double pression ............................................................... alternance entre les p aramètres Courte pression ................................................................ Modification du p aramètre sélectionné Après 30 s. sans commande ....................................... Interruption automatique sans sauveg arde Maintenir enfoncé (env. 3 s.) lors de l'activation ...... Sauveg arder et quitter Le mode de fonction peut être modifié au moyen du logiciel d'installation du serveur digitalSTROM mais aussi en utilisant la touche. Paramètres en d éta il : Paramètre 1: commuter : LED clignote ; b alayer : LED allumée, flash court ; économiser : LED s'éteint Paramètre 2: LED change de couleur ; ordre des afficha ges : arc-en-ciel…. couleur sélectionnée… arc-en-ciel… couleur sélectionnée… Paramètre 3: touche a pp areil : LED allumée ; touche pièce : LED clignote 5x; Touche zone 1 (ou 2, 3, 4): LED clignote 1x (ou 2x, 3x, 4x) Attribution d es fonctions sortie usine : groupe de couleurs réglé .................................................................... noir (Joker) Sortie ....................................................................................................... mode économique Bouton-pression ..................................................................................... touche a pp areil G arantie : aizo a g assure un p arfait fonctionnement du produit, conformément à la spécification pend ant une durée de 24 mois a près la livraison p ar aizo a g. L'ouverture de l'a pp areil, toute tentative d'ouverture de l'a pp areil ou une installation/configuration incorrecte annulent la validité de la g arantie. Interruption du rése au : La prise intermédiaire sauveg arde la sortie dès qu'il reste inchangé pend ant au moins 5 secondes. Après une interruption du rése au, l'état sauveg ardé à la sortie est de nouve au réta bli. C ara ctéristiques techniques : Principe de commutation ..................................................................... relais électrom. DE2a-L2-24D Consommateur de ohms ...................................................................... ° 撰 2300 W (10A) Surcharg e : La prise intermédiaire reconnaît les surcharges et coupe la sortie. Une remise à zéro se produit au cours du prochain a ppel de scène (commande via digitalSTROM ou p ar touche), à la condition qu'aucune autre surcharge ne soit présente). Surchauffe : La sortie est coupée tant qu'une surcharge thermique est présente sur une longue durée. Celle-ci est réta blie automatiquement a près la phase de refroidissement. Consommateur inductif/ca p acitif ....................................................... ° 撰 700 W (3A)* Tension d'entrée nominale /fréquence .............................................. 230 V AC/50 Hz Puissance a bsorbée .............................................................................. 0,4 W Type de protection (pièces sèches) ................................................... IP20 EN 60529 Temp. ambiante a dmise (service) ..................................................... 0°C ... +35°C Transmission de données via rése au 230 V AC ............................. protocole digitalSTROM V1.0 * Fonction nominale. Respecter les courants d'entrée de la charge.