Download "取扱説明書"

HDR-CX500/CX500E/CX500V/CX500VE/CX505VE
/CX520/CX520E/CX520V/CX520VE
RMT-835
SERVICE MANUAL
LEVEL
Ver. 1.1 2009.12
Revision History
Photo: HDR-CX500
2
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
• Precaution on Replacing the VC-575 Board
• Precaution on Replacing the CABINET (BOTTOM) ASSY
• Precaution on Replacing the MM-083 Board
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
9-852-714-32
Sony EMCS Co.
2009L0800-1
© 2009.12
Published by Tokai TEC
These specifications are extracted from instruction manual of
HDR-CX500E/CX500VE/CX505VE/CX520E/CX520VE.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
Signal format: PAL color, CCIR standards HDTV
1080/50i specification
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB
Movie recording format:
Video: HD: MPEG-4 AVC/H.264 AVCHD
format compatible
SD: MPEG-2 PS
Audio: Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
LCD screen
Picture: 7.5 cm (3.0 type, aspect ratio 16:9)
Total number of pixels: 230 400 (960 × 240)
General
Photo file format
: DCF Ver.2.0 Compatible
: Exif Ver.2.21 Compatible
: MPF Baseline Compatible
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording, using LCD screen at normal
brightness: HD: 3.4 W SD: 2.7 W
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (-4 °F to
+140 °F)
Dimensions (approx.):
62 × 65 × 125 mm (2 1/2 × 2 5/8 × 5 in.)
(w/h/d) including the projecting parts
62 × 65 × 133 mm (2 1/2 × 2 5/8 × 5 3/8 in.)
(w/h/d) including the projecting parts, and
the supplied rechargeable battery pack attached
Mass (approx.)
HDR-CX500E/CX520E:
360 g (13 oz) main unit only
440 g (16 oz) including the supplied
rechargeable battery pack
HDR-CX500VE/CX505VE/CX520VE:
370 g (13 oz) main unit only
450 g (1 lb) including the supplied
rechargeable battery pack
Recording media (Movie/Photo)
Internal memory
HDR-CX500E/CX500VE/CX505VE: 32GB
HDR-CX520E/CX520VE: 64GB
“Memory Stick PRO Duo” media
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is below.
HDR-CX500E:
approximately 31.5 GB
HDR-CX500VE/CX505VE:
approximately 30.7 GB
HDR-CX520E:
approximately 63.5 GB
HDR-CX520VE:
approximately 62.7 GB
Image device: 6.3 mm (1/2.88 type) CMOS sensor
Recording pixels (photo, 4:3):
Max. 12.0 mega (4 000 × 3 000) pixels*
Gross: Approx. 6 631 000 pixels
Effective (movie, 16:9):
Approx. 4 150 000 pixels**
Effective (photo, 16:9):
Approx. 4 500 000 pixels
Effective (photo, 4:3):
Approx. 6 000 000 pixels
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (–4 °F to
+140 °F)
Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
× 1 3/16 × 3 1/4 in.) (w/h/d) excluding the
projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
Lens: Sony G lens
12 × (Optical), 24 × , 150 × (Digital)
Filter diameter: 37 mm (1 1/2 in.)
F1.8 ~ 3.4
Focal length:
f=5.5 ~ 66.0 mm (7/32 ~ 2 5/8 in.)
When converted to a 35 mm still camera
For movies: 43 ~ 516 mm (1 3/4 ~ 20 3/8
in.)** (16:9)
For photos: 38 ~ 456 mm (1 1/2 ~ 18 in.) (4:3)
* See the label on the AC Adaptor for other
specifications.
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR]
(5 800 K)
Rechargeable battery pack NP-FH60
Maximum output voltage: DC 8.4 V
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity: 7.2 Wh (1 000 mAh)
Type: Li-ion
Minimum illumination
11 lx (lux) (in default setting, shutter speed 1/50
second)
3 lx (lux) (LOW LUX is set to [ON], shutter speed
1/25 second)
0 lx (lux) (NIGHTSHOT is set to [ON])
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
* The unique pixel array of Sony's ClearVid
and the image processing system
(BIONZ) allow still image resolution
equivalent to the sizes described.
** [ STEADYSHOT] is set to
[STANDARD] or [OFF].
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—2—
These specifications are extracted from instruction manual of
HDR-CX500/CX500V/CX520/CX520V.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
Signal format: NTSC color, EIA standards HDTV
1080/60i specification
A/V Remote Connector: Component/video and
audio output jack
HDMI OUT jack: HDMI mini connector
USB jack: mini-AB
Movie recording format:
Video: HD: MPEG-4 AVC/H.264 AVCHD
format compatible
SD: MPEG-2 PS
Audio: Dolby Digital 2ch/5.1ch
Dolby Digital 5.1 Creator
LCD screen
Picture: 7.5 cm (3.0 type, aspect ratio 16:9)
Total number of pixels: 230 400 (960 × 240)
General
Photo file format
: DCF Ver.2.0 Compatible
: Exif Ver.2.21 Compatible
: MPF Baseline Compatible
Power requirements: DC 6.8 V/7.2 V (battery
pack) DC 8.4 V (AC Adaptor)
Average power consumption: During camera
recording, using LCD screen at normal
brightness: HD: 3.6 W SD: 2.7 W
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (-4 °F to
+140 °F)
Dimensions (approx.):
62 × 65 × 125 mm (2 1/2 × 2 5/8 × 5 in.)
(w/h/d) including the projecting parts
62 × 65 × 133 mm (2 1/2 × 2 5/8 × 5 3/8 in.)
(w/h/d) including the projecting parts, and
the supplied rechargeable battery pack attached
Mass (approx.)
HDR-CX500/CX520:
360 g (13 oz) main unit only
440 g (16 oz) including the supplied
rechargeable battery pack
HDR-CX500V/CX520V:
370 g (13 oz) main unit only
450 g (1 lb) including the supplied
rechargeable battery pack
Recording media (Movie/Photo)
Internal memory
HDR-CX500/CX500V: 32GB
HDR-CX520/CX520V: 64GB
“Memory Stick PRO Duo” media
When measuring media capacity, 1 GB equals
1 billion bytes, a portion of which is used for
system management and/or application files.
The capacity that a user can use is below.
HDR-CX500:
approximately 31.5 GB
HDR-CX500V:
approximately 30.7 GB
HDR-CX520:
approximately 63.5 GB
HDR-CX520V:
approximately 62.7 GB
Image device: 6.3 mm (1/2.88 type) CMOS sensor
Recording pixels (photo, 4:3):
Max. 12.0 mega (4 000 × 3 000) pixels*
Gross: Approx. 6 631 000 pixels
Effective (movie, 16:9):
Approx. 4 150 000 pixels**
Effective (photo, 16:9):
Approx. 4 500 000 pixels
Effective (photo, 4:3):
Approx. 6 000 000 pixels
AC Adaptor AC-L200C/AC-L200D
Power requirements: AC 100 V - 240 V,
50 Hz/60 Hz
Current consumption: 0.35 A - 0.18 A
Power consumption: 18 W
Output voltage: DC 8.4 V*
Operating temperature: 0 °C to 40 °C (32 °F to
104 °F)
Storage temperature: –20 °C to + 60 °C (–4 °F to
+140 °F)
Dimensions (approx.): 48 × 29 × 81 mm (1 15/16
× 1 3/16 × 3 1/4 in.) (w/h/d) excluding the
projecting parts
Mass (approx.): 170 g (6.0 oz) excluding the
power cord (mains lead)
Lens: Sony G lens
12 × (Optical), 24 × , 150 × (Digital)
Filter diameter: 37 mm (1 1/2 in.)
F1.8 ~ 3.4
Focal length:
f=5.5 ~ 66.0 mm (7/32 ~ 2 5/8 in.)
When converted to a 35 mm still camera
For movies: 43 ~ 516 mm (1 3/4 ~ 20 3/8
in.)** (16:9)
For photos: 38 ~ 456 mm (1 1/2 ~ 18 in.) (4:3)
* See the label on the AC Adaptor for other
specifications.
Color temperature: [AUTO], [ONE PUSH],
[INDOOR] (3 200 K), [OUTDOOR]
(5 800 K)
Rechargeable battery pack NP-FH60
Maximum output voltage: DC 8.4 V
Output voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 2.12 A
Capacity: 7.2 Wh (1 000 mAh)
Type: Li-ion
Minimum illumination
11 lx (lux) (in default setting, shutter speed 1/60
second)
3 lx (lux) (LOW LUX is set to [ON], shutter speed
1/30 second)
0 lx (lux) (NIGHTSHOT is set to [ON])
Design and specifications of your camcorder and
accessories are subject to change without notice.
• Manufactured under license from Dolby
Laboratories.
* The unique pixel array of Sony's ClearVid
and the image processing system
(BIONZ) allow still image resolution
equivalent to the sizes described.
** [ STEADYSHOT] is set to
[STANDARD] or [OFF].
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—3—
ENGLISH
JAPANESE
概略仕様
システム
入/出力端子
信号方式：NTSCカラー、EIA標準方式
A/Vリモート端子：コンポーネント、映像音声出力兼用端子
HDMI端子：HDMIミニコネクタ
USB端子：mini-AB
ビデオ記録方式
映像：HD画質：MPEG-4 AVC/H.264
AVCHD規格準拠
SD画質：MPEG-2 PS
音声：Dolby Digital 2ch/5.1ch
ドルビーデジタル5.1クリエーター搭載
液晶画面
画面サイズ：7.5 cm（3.0型、アスペクト比16：9）
総ドット数：230 400ドット
横960×縦240
静止画ファイルフォーマット
：DCF Ver2.0準拠
：Exif Ver2.21準拠
：MPF Baseline準拠
電源部、その他
電源電圧：バッテリー端子入力 6.8 V/7.2 V
DC端子入力 8.4 V
消費電力：液晶画面の明るさ標準：
HD：3.6 W
SD：2.7 W
動作温度：0 ℃∼ 40 ℃
保存温度：−20 ℃∼ +60 ℃
外形寸法：62 × 65 × 125 mm
(突起部を含む)(幅×高さ×奥行き)
62 × 65 × 133 mm
(突起部を含む、付属バッテリー装着状態)
(幅×高さ×奥行き）
本体質量：
約370 g（本体のみ）
撮影時総質量：
約450 g（付属バッテリー含む。）
記録メディア (動画・静止画)
内蔵メモリー
HDR-CX500V：32GB
HDR-CX520V：64GB
“メモリースティック PRO デュオ”
容量は、１GBを10億バイトで計算した場合の数
値です。また管理用ファイル、アプリケーショ
ンファイルなどを含むため、実際に使用できる
容量は減少します。ご使用いただけるユーザー
容量は、次のとおりです。
HDR-CX500V 約30.7GB
HDR-CX520V 約62.7GB
撮像素子：6.3 mm (1/2.88型）CMOSセンサー
記録画素数：静止画時最大 1 200万画素相当＊
(4 000×3 000） (4：3時)
総画素数：約663万画素
動画時有効画素数 (16：9)：約415万画素＊＊
静止画時有効画素数 (16：9)：約450万画素
静止画時有効画素数 (4：3)：約600万画素
ACアダプター AC-L200C/AC-L200D
電源：AC 100 V - 240 V、50 Hz/60 Hz
消費電力：18 W
定格出力：DC 8.4 V＊
動作温度：0 ℃∼ 40 ℃
保存温度：−20 ℃∼ +60 ℃
外形寸法：約 48×29×81 mm (最大突起部をのぞく)
(幅×高さ×奥行き）
質量：約170 g (本体のみ)
ズームレンズ：ソニー Gレンズ
12倍（光学)、24倍、150倍 (デジタル)
フィルター径：37 mm
F1.8∼ 3.4
f=5.5∼ 66.0 mm
35mmカメラ換算では
動画撮影時：
43∼ 516 mm (16：9)＊＊
静止画撮影時：
38∼ 456 mm (4：3)
＊
その他の仕様についてはACアダプターのラベルを
ご覧ください。
リチャージャブルバッテリーパック
NP-FH60
最大電圧：DC 8.4 V
公称電圧：DC 7.2 V
容量： 7.2 Wh (1 000mAh)
使用電池：Li-ion
色温度切り換え：[オート]、[ワンプッシュ]、[屋内]
(3 200 K)、[屋外](5 800 K)
本機やアクセサリーの仕様および外観は、改良のため
予告なく変更することがありますが、ご了承ください。
最低被写体照度：
11 lx (ルクス) (お買い上げ時、[シャッタース
ピード] 1/60秒)
3 lx (ルクス) (LOW LUX時、[シャッタースピー
ド] 1/30秒)
0 lx (ルクス) (NIGHTSHOT時）
• ドルビーラボラトリーズからの実施権に基づき
製造されています。
＊
ソニー独自のクリアビッド画素配列と画像処
理システムBIONZにより、静止画は表記の記
録サイズを実現しています。
＊＊ [
手ブレ補正機能]が[スタンダード]、または
[切]のとき。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—4—
Model information table
Model
HDR-CX500
HDR-CX500E
HDR-CX500V
HDR-CX500VE
HDR-CX505VE
Destination
E, KR
NE, E,
CH, HK, JE
US, CND, J
AUS
AEP, UK
Color system
NTSC
PAL
NTSC
PAL
PAL
GPS function
Not built in
Not built in
Built in
Built in
Built in
32GB
32GB
32GB
32GB
32GB
Input/Output
Input/Output
Input/Output
Input/Output
Output only
×
×
Ο
Ο
Ο
Internal memory
USB function
FP-1021 flexible board
HDR-CX520
HDR-CX520E
HDR-CX520V
HDR-CX520VE
E
NE, E,
CH, JE
US, CND, J
AEP, UK, AUS
Color system
NTSC
PAL
NTSC
PAL
GPS function
Not built in
Not built in
Built in
Built in
Model
Destination
Internal memory
USB function
FP-1021 flexible board
64GB
64GB
64GB
64GB
Input/Output
Input/Output
Input/Output
Input/Output
×
×
Ο
Ο
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—5—
ENGLISH
JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—6—
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
使用済の電池は，取扱指示に従って処分してください。
サービス，点検時には次のことにご注意下さい。
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
特に回路図，部品表に0 印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとど
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
換時は注意して下さい。
6. フレキシブルプリント基板の取扱いについて
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
（３回以内）
• パターンに力が加わらないよう注意して下さい。
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（Lead Free）を意
味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
いてもレッドフリーマークがプリントされて
いないものがあります）
：レッドフリーマーク
無鉛半田には，以下の特性があります。
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
350℃に設定して下さい。
注意： 半田こてを長く当てすぎると，基板のパター
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—7—
Ver. 1.1 2009.12
The changed portions from
Ver. 1.0 are shown in blue.
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200C/L200D).
1-2. PRECAUTION ON REPLACING THE VC-575 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Start the Adjust Manual in the Adjust Station and execute the [DESTINATION DATA WRITE].
DESTINATION DATA WRITE
After the board replacement, the error of the built-in recording media may be displayed. in this case, execute the [DESTINATION DATA
WRITE] then the error will be cleared. If it is not cleared with [DESTINATION DATA WRITE], format the built-in recording media.
USB SERIAL SAVE
When you replace to the repairing board, get the data from the former one.
Start the Adjust Manual in the Adjust Station and perform “USB SERIAL SAVE” to get the data.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Start the Adjust Manual in the Adjust Station and execute the “USB serial No. input”.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-1
ENGLISH
JAPANESE
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do. This function consists of two display; self-diagnosis display and
service mode display.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the counter of the
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
LCD screen
C:31:11
Blinks at 3.2Hz
C
Repaired by:
31
11
Block
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
Detailed Code
Refer to “1-3-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
1-3-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Symptom/State
Detailed
Code
Correction
Non-standard battery is used.
The battery pack temperature is high.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
C
C
0
0
4
6
0
0
0
0
C
1
3
0
1
C
1
3
0
2
Access error
C
3
2
6
0
Difficult to adjust focus
(Cannot initialize focus)
E
2
0
0
0
Flash memory data are rewritten.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
1
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
E
6
1
1
Use the InfoLITHIUM battery.
Change the battery pack or place it in a cool place.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin e;, ea of
CN1010 on the VC-575 board). If it is OK, check the focus
motor drive IC (IC5201 on the VC-575 board).
Make flash memory data correct value. (Note 1)
Inspect the lens block zoom MR sensor (pin ef, eg of CN1010
on the VC-575 board) when zooming is performed when the
zoom lever is operated, or the zoom motor drive circuit (IC5201
on the VC-575 board) when zooming is not performed.
Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
Note 1 : Start the Adjust Manual in the Adjust Station and refer to the “Destination data write”.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-2
ENGLISH
JAPANESE
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
E
6
2
0
0
E
6
2
0
1
E
6
2
0
2
E
6
2
0
3
E
6
2
0
4
E
6
2
1
0
E
6
2
1
1
E
6
2
1
2
E
6
2
2
0
E
9
1
0
1
E
9
2
0
1
E
9
4
0
0
E
9
4
0
1
E
9
4
0
2
E
9
5
0
0
E
9
6
0
0
Correction
Symptom/State
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Inspect PITCH angular velocity sensors (SE6601 on the MM-083
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE6601 on the MM-083
board) peripheral circuits.
Refer to [1-4-1. E : 62 : 02 (Abnormality of IC for Steadyshot)
Occurred].
Abnormality of IC for steadyshot.
IC for steadyshot and micro controller
Inspect the steadyshot circuit (IC5501 on the VC-575 board).
communication abnormality among.
Inspect the image vibraton angular velocity sensors
Image vibration correction during
(SE9001 on the ST-217 board) peripheral circuits.
handshake function does not work.
Replacement of lens block. If an error occurs again, replace the
Shift lens initializing failure.
VC-575 board. (Note 2)
Refer to [1-4-2. E : 62 : 11 (Shift Lens Overheating (Pitch))
Shift lens overheating (Pitch)
Occurred].
Refer to [1-4-3. E : 62 : 12 (Shift Lens Overheating (Yaw))
Shift lens overheating (Yaw)
Occurred].
Refer to [1-4-4. E : 62 : 20 (Abnormality of Thermistor)
Abnormality of thermistor.
Occurred].
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit.
Check the remaining battery power because this symptom maybe
depended on the remaining battery level, and confirm whether or
not the symptom is occured after replacing the battery.
Battery current value goes over the
If the symptom is still occured, overhaul inspection is needed.
max discharge current
Check each output of DC/DC converter (IC4701) on VC-575
board connected to CK-217 board with FP-1127 board, and
connect DC/Batt harness (the minimum connection to periphery)
to VC-575 board.
Fault of writing or erasing the
Inspect the flash memory (IC8101 on the VC-575 board).
flash memory
Inspect the flash memory (IC8101 on the VC-575 board).
Internal flash memory fault
Inspect the flash memory (IC8101 on the VC-575 board). If it is
BGM data error
OK, check the CPU (IC7501 on the VC-557 board).
CX500V/CX500VE/CX505VE/CX520V/CX520VE
Check whether the flexible board of the GPS module is broken,
and check whether it is inserted imperfectly. If there is no
GPS hardware error
problem the flexible board, inspect or replacement of the GPS
module.
CX500V/CX500VE/CX505VE/CX520V/CX520VE
Map area mount error
Inspect or replacement of the MM-083 board.
Note 2 : When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-3
ENGLISH
JAPANESE
1-4. METHOD OF COPING WITH SHIFT LENS ERROR
VC-575 BOARD (SIDE A)
VC-575 BOARD (SIDE B)
IC7501
*R5653
R5527
R5524
IC5501
*R5653:
No mount (Short land)
Fig. 1
Measurement points on the VC-575 board
about 330 msec
Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5653 land on the VC-575 board
1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5653 land in the periphery of IC5501 on the VC-575 board, turn
the power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC7501 of VC-575 board) periphery.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-4
ENGLISH
JAPANESE
1-4-2. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
01
Procedure
1
11
80
7430
Write the data. (After it starts, set it before caution is displayed.)
2
11
8E
F654
01
Write the data.
3
11
8E
F655
F0
Write the data.
4
11
8E
F658
01
Write the data. (Note 1)
5
11
8E
F658
00
Write the data.
6
11
8E
F654
00
Write the data.
7
11
8E
F655
10
Write the data.
8
11
8E
F658
01
Write the data. (Note 1)
9
11
8E
F658
00
Write the data.
10
11
80
7430
00
Write the data.
11
Check if the shift lens moves while setting the order 2 to 9. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 12.
12
While setting the order 2 to 9, measure with an oscilloscope the output voltage of R5527 in the
periphery of IC5501 on the VC-575 board to check the output voltage varies.
13
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 14.
14
Turn the power OFF.
15
While measuring with an oscilloscope the output voltage of R5653 land in the periphery of
IC5501 on the VC-575 board, turn the power ON to check that the output voltage immediately
after the power on change as shown in Fig. 2.
16
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC7501 of VC-575 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F658, data: 00, and then retry.
Note 2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-5
ENGLISH
JAPANESE
1-4-3. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Connect by the SeusEX and perform the following process.
Order Block Page Address Data
01
Procedure
1
11
80
7430
Write the data. (After it starts, set it before caution is displayed.)
2
11
8E
F656
01
Write the data.
3
11
8E
F657
F0
Write the data.
4
11
8E
F659
01
Write the data. (Note 1)
5
11
8E
F659
00
Write the data.
6
11
8E
F656
00
Write the data.
7
11
8E
F657
10
Write the data.
8
11
8E
F659
01
Write the data. (Note 1)
9
11
8E
F659
00
Write the data.
10
11
80
7430
00
Write the data.
11
Check if the shift lens moves while setting the order 2 to 9. If the shift lens does not move,
replace the lens block (Note 2). When the shift lens moved, proceed to the order 12.
12
While setting the order 2 to 9, measure with an oscilloscope the output voltage of R5524 in the
periphery of IC5501 on the VC-575 board to check the output voltage varies.
13
If the output voltage does not vary, replace the lens block (Note 2). When the output voltage
varied, proceed to the order 14.
14
Turn the power OFF.
15
While measuring with an oscilloscope the output voltage of R5653 land in the periphery of
IC5501 on the VC-575 board, turn the power ON to check that the output voltage immediately
after the power on change as shown in Fig. 2.
16
If the output voltage change as shown in Fig. 2, replace the lens block (Note 2). If it does not
change as shown in Fig. 2, inspect the camera control circuit (IC7501 of VC-575 board)
periphery.
Note 1: Finish this operation within 10 seconds. If it is likely to take more than 10 seconds, set block: 11, page: 8E, address:
F659, data: 00, and then retry.
Note 2: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
1-4-4. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Confirm the connections of flexible flat cables and connectors between the lens block and VC-575 board.
3
In case of no malfunction of connections, replace the lens block with new one. (Note) When the error has occurred in spite of the
lens replacement, replace VC-575 board with new one.
Note: When the lens block was replaced, start the Adjust Manual in the Adjust Station and execute the necessary adjustment
items.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the
handheld operation.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-6
ENGLISH
1-5. GPS RECEIVING CHECK (CX500V/CX500VE/CX505VE/CX520V/CX520VE)
After a part of set was replaced or after the set was assembled, check the reception of GPS signal.
How to check the GPS function
Bring your camcorder to an open area, and set the GPS switch to ON (
appears on the LCD
screen). Your camcorder starts trying to triangulate. When your camcorder triangulates
successfully, it will record the location information at the time movies and photos were recorded.
Notes
• The indicator changes according to the strength of GPS signal reception.
Triangulating status
GPS indicators GPS reception status
Function off
No indicator
The GPS switch is set to OFF, or the GPS receiver is not
functioning normally.
Difficult
Your camcorder cannot find a GPS signal, therefore, it cannot
triangulate. Use your camcorder in an open area.
Processing
Your camcorder is confirming the GPS signal, and will be able
to acquire location information soon. Wait until your camcorder
completes the triangulation.
Triangulating
Your camcorder is receiving a GPS signal, and can acquire location
information.
Triangulating
Your camcorder is receiving a strong GPS signal, and can acquire
location information.
• It may take from several seconds to several minutes to acquire the location information when you use the
GPS for the first time or use it again after long intervals.
• You may not be able to acquire location information depending on the strength of GPS reception.
• When
is displayed and it takes a while to triangulate, set the GPS switch to OFF, then set to ON again.
1-6. PRECAUTION ON REPLACING THE MM-083 BOARD
Do not factory check MM-083 board in which Map Data is installed (CX500V/CX500VE/CX505VE/CX520V/CX520VE).
The map data is erased when the factory check is done.
Angular Velocity Sensor
When you replace to the reparing board, write down the sensitivity displayed on the angular velocity sensor (SE6601).
Start the Adjust Manual in the Adjust Station and execute the “GYRO sensor sensitivity adj”.
MM-083 BOARD (SIDE B)
SE6601
YYY
PPP
YYY:
YAW sensor sensitivity
t
PPP:
PITCH sensor sensitivity
Note: The sensor sensitivity of SE6601 of MM-083 board is written only repair parts.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-7
G2
t
G1
JAPANESE
Ver. 1.1 2009.12
Ver.1.0からの変更部分は
青色で記載されています。
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなります。
これを避けるため，下記の方法を用いてください。
方法：
ACアダプタ（AC-L200C/L200D）を使用する。
1-2. VC-575基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
Adjust StationからAdjust Manualを起動させて「DESTINATION DATA WRITE」を実行させてください。
仕向けデータ設定
補修用基板交換後、電源を入れると内蔵記録メディアエラーが表示される場合がありますが、「D E S T I N A T I O N D A T A
WRITE」を実行させると消えます。「DESTINATION DATA WRITE」実行しても消えない場合は、内蔵記録メディアを
フォーマットしてください。
USBシリアルセーブ
補修用基板と交換する時，交換前の基板よりUSBシリアルNo.を取得してください。
データの取得はAdjust StationからAdjust Manualを起動させて「USB SERIAL SAVE」を実行させてください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
Adjust StationからAdjust Manualを起動させて「USB serial No. input」を実行させてください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-8
ENGLISH
JAPANESE
1-3. 自己診断機能
1-3-2. 自己診断表示
本機の動作に不具合が生じたとき，LCD画面のカウンタ表示
部分がアルファベットと数字の4 桁表示になり，3 . 2 H z で点
滅します。この5 文字の表示によって対応者分類および不具
合の生じたブロックの分類，不具合の詳細コードを示しま
す。
1-3-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。「自己診断表示」と「サービスモード表示」の２つの表
示があります。自己診断機能については取扱説明書にも掲載
されています。
LCD画面
C:31:11
3.2Hz点滅
C
対応者分類
11
31
ブロック分類
詳細コード
対応方法の違いにより分類 「1-3 -3 . 自己診断コード表」
例 31 ･･･テープを入れ直す を参照
32 ･･･電源を入れ直す
C ：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
で対応
1-3-3. 自己診断コード表
自己診断コード
対 ブロック
応
機能
者
詳細
コード
C
0
4
0
0
標準以外のバッテリを使用している インフォリチウムバッテリを使用する。
C
0
6
0
0
バッテリが高温になっている
C
1
3
0
1
フォーマットしていない“メモリー “メモリーステック デュオ”をフォーマットする。
ステック デュオ”を入れた
“メモリーステック デュオ”が壊 新しい“メモリーステック デュオ”に交換する。
れている
C
1
3
0
2
アクセスエラー
C
3
2
6
0
フォーカスが合いにくい
操作スイッチの電源を入れ直す。
（フォーカスの初期化ができない） 復帰しない場合，レンズブロックのフォーカスMRセンサ
（VC-575基板CN1010 e;，eaピン）を点検する。異常なけ
ればフォーカスモータ駆動回路（VC-575基板IC5201）を点
検する。
E
2
0
0
0
フラッシュメモリが書き換えられている フラッシュメモリのデータを元の値に戻す。（注意1）
E
6
1
1
0
ズーム動作の異常（ズームレンズの ズームレバーを操作したときにズーム動作をすれば，レン
初期化ができない）
ズブロックのズームMRセンサ（VC-575基板CN1010ef，eg
ピン）を点検する。ズーム動作をしなければズームモータ
駆動回路（VC-575基板IC5201）を点検する。
E
6
1
1
1
フォーカス，ズーム異常
症状／状態
対応／方法
バッテリを交換するか，バッテリを涼しいところに置く。
電源を外し，再度入れ直してから操作する。
自己診断コードC：32：60とE：61：10の両方を点検する。
注意1：Adjust StationからAdjust Manualを起動させて，
「 Destination data write 」を参照してください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-9
ENGLISH
JAPANESE
自己診断コード
対 ブロック
応
機能
者
詳細
コード
E
6
2
0
0
手振れ補正が効きにくい（PITCH
角速度センサ出力張り付き）
PITCH角速度センサ（MM-083基板SE6601）周辺回路を点
検する。
E
6
2
0
1
手振れ補正が効きにくい（YAW 角
速度センサ出力張り付き）
YAW角速度センサ（MM-083基板SE6601）周辺回路を点
検する。
E
6
2
0
2
手振れ補正用ICの異常
E
6
2
0
3
手振れ補正用ICとマイクロコント
ローラーとの通信異常
E
6
2
0
4
Active手振れ補正時の画ゆれが補正 画ゆれ検出角速度センサ (ST-217基板SE9001) 周辺回路を点
できない (角速度センサ出力張り付き) 検する。
E
6
2
1
0
シフトレンズ初期化異常
E
6
2
1
1
シフトレンズオーバーヒート
(PITCH)
「1-4-2. E：62：11（シフトレンズオーバーヒート
（PITCH）
）
が出
た場合」を参照。
E
6
2
1
2
シフトレンズオーバーヒート
(YAW)
「1-4-3. E：62：12（シフトレンズオーバーヒート（YAW）
）
が出
た場合」を参照。
E
6
2
2
0
サーミスタの異常
「1-4-4. E：62：20（サーミスタの異常）が出た場合」を参照。
E
9
1
0
1
フラッシュの充電異常
E
9
2
0
1
(バッテリーの) 電流値が最大放電電 バッテリ残量に依存する場合があるので，バッテリ残量
流を超えた
を確認する。次にバッテリを交換して症状が出るか確認す
る。バッテリを交換しても症状が出る場合は，エラー発生
後に電源が切れてしまうため，分解して確認する，VC575基板にCK-217基板をFP-1127 (VC-CK) フレキシブル基
板で接続し，DC/バッテリハーネスをVC-575基板に接続し
た状態 (最小限の接続) でDC／DCコンバータ (VC-575基板
IC4701) の各チャンネル出力を確認する。
E
9
4
0
0
フラッシュメモリの書込み/消去動
作不良
フラッシュメモリ（VC-575基板 IC8101）を点検する。
E
9
4
0
1
フラッシュメモリ内部異常
フラッシュメモリ（VC-575基板 IC8101）を点検する。
E
9
4
0
2
BGM データ異常
フラッシュメモリ（VC-575基板 IC8101）を点検する。異常が
ない場合は，CPU（VC-575基板 IC7501）を点検する。
E
9
5
0
0
GPSハードウェア異常
CX500V/CX520V
GPS モジュールのフレキシブル基板が切れていないか，ま
た完全に挿入されているかを点検する。フレキシブル基板
に問題がない場合は，GPS モジュールの点検または交換を
する。
E
9
6
0
0
MAPエリアマウント異常
CX500V/CX520V
MM-083基板の点検または交換をする。
症状／状態
対応／方法
「1-4-1. E：62：02（手振れ補正用ICの異常）
が出た場合」
を参照。
手振れ補正回路（VC-575基板IC5501）
を点検する。
レンズブロックを交換する。エラーが再度発生する場合
は， VC-575基板を交換する。
（注意2）
フラッシュユニットの点検または交換をする。
注意2：レンズブロックを交換した場合は，Adjust StationからAdjust Manualを起動させて，必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-10
ENGLISH
JAPANESE
1-4. シフトレンズエラーの対処方法
VC-575 BOARD (SIDE A)
VC-575 BOARD (SIDE B)
IC7501
*R5653
R5527
R5524
IC5501
*R5653:
No mount (Short land)
図1.VC-575基板測定箇所
約 330 msec
注意：Lowの区間の長さは場合によって多少異なる
図2. VC-575基板R5653ランドの出力電圧の変化
1-4-1. E：62：02
（手振れ補正用ICの異常）が出た場合
順序
1
2
3
作業内容
電源を切る。
VC-575基板IC5501の周辺にあるR5653ランドの出力電圧をオシロスコープで測定しながら電源を入れる。電源投入
直後の出力電圧が図2の様に変化することを確認する。
出力電圧が図2 の様に変化するときはレンズブロックを交換する
（注意）。図2 の様に変化しないときはカメラコン
トロール回路（VC-575基板IC7501）周辺を点検する。
注意： レンズブロックを交換した場合は，Adjust StationからAdjust Manualを起動させて，必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-11
ENGLISH
JAPANESE
1-4-2. E：62：11
（シフトレンズオーバーヒート（PITCH））が出た場合
SeusEXで接続し、次の手順を行う。
順序 ブロック ページ アドレス データ
1
11
80
7430
01
2
11
8E
F654
01
3
11
8E
F655
F0
4
11
8E
F658
01
5
11
8E
F658
00
6
11
8E
F654
00
7
11
8E
F655
10
8
11
8E
F658
01
9
11
8E
F658
00
10
11
80
7430
00
11
12
13
14
15
16
作業内容
データを書き込む。（セット起動後，コーションが表示される前に設定する事。）
データを書き込む。
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
データを書き込む。
データを書き込む。（注意1）
データを書き込む。
データを書き込む。
順序2∼9を設定している間にシフトレンズが動いたか確認する。もしシフト
レンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序
12に進む。
VC-575基板IC5501の周辺にあるR5527の出力電圧をオシロスコープで測定
しながら，順序2∼9を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する
（注意2）
。変化するときは
順序14に進む。
電源を切る。
VC-575基板IC5501の周辺にあるR5653ランドの出力電圧をオシロスコープで測
定しながら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを
確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2
の様に変化しないときはカメラコントロール回路
（VC-575基板IC7501）
周辺を
点検する。
注意1：この操作は1 0 秒以内に終了してください。もし1 0 秒以上経過しそうな場合は，ブロック：1 1 ，ページ：8 E ，アド
レス：F658，データ：00 に設定しなおしてから再度実行してください。
注意2：レンズブロックを交換した場合は，Adjust StationからAdjust Manualを起動させて，必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-12
ENGLISH
JAPANESE
1-4-3. E：62：12
（シフトレンズオーバーヒート
（YAW））が出た場合
SeusEXで接続し、次の手順を行う。
順序 ブロック ページ アドレス データ
作業内容
1
11
80
7430
01
データを書き込む。（セット起動後，コーションが表示される前に設定する事。）
2
11
8E
F656
01
データを書き込む。
3
11
8E
F657
F0
データを書き込む。
4
11
8E
F659
01
データを書き込む。（注意1）
5
11
8E
F659
00
データを書き込む。
6
11
8E
F656
00
データを書き込む。
7
11
8E
F657
10
データを書き込む。
8
11
8E
F659
01
データを書き込む。（注意1）
9
11
8E
F659
00
データを書き込む。
10
11
80
7430
00
データを書き込む。
順序2∼9を設定している間にシフトレンズが動いたか確認する。もしシフトレ
11
ンズが動かない場合はレンズブロックを交換する（注意2）。動く場合は順序12
に進む。
VC-575基板IC5501の周辺にあるR5524の出力電圧をオシロスコープで測定し
12
ながら，順序2∼9を設定したときに出力電圧が変化することを確認する。
出力電圧が変化しないときはレンズブロックを交換する
（注意2）
。変化するときは
13
順序14に進む。
14
電源を切る。
VC-575基板IC5501の周辺にあるR5653ランドの出力電圧をオシロスコープで測
15
定しながら電源を入れる。電源投入直後の出力電圧が図2の様に変化することを
確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する（注意2）。図2
16
の様に変化しないときはカメラコントロール回路（VC-575基板IC7501）
周辺を
点検する。
注意1 ：この操作は1 0 秒以内に終了してください。もし1 0 秒以上経過しそうな場合は，ブロック：1 1 ，ページ：8 E ，アド
レス：F659，データ：00 に設定しなおしてから再度実行してください。
注意2：レンズブロックを交換した場合は，Adjust StationからAdjust Manualを起動させて，必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-4-4. E：62：20
（サーミスタの異常）が出た場合
順序
1
2
3
作業内容
電源を入れる。
レンズブロックとVC-575基板間の各フレキシブルフラットケーブルとコネクタの接続を確認する。
接続に異常がなければレンズブロックを交換する。（注意）
交換してもエラーが発生する場合はVC-575基板を交
換する。
注意： レンズブロックを交換した場合は，Adjust StationからAdjust Manualを起動させて，必要な調整項目を実施すること。
調整後は手振れ補正ONの状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-13
ENGLISH
1-5. GPS 受信確認 (CX500V/CX520V)
部品交換やセット組み立て後は，GPS 信号受信確認を行ないます。
GPS 機能確認方法
空の開けた場所で，GPSスイッチを「ON」にすると、 が表示され、測位準備が行われます。
測位できた場合、動画・静止画の撮影時に位置情報を記録します。
ご注意
• GPS衛星からの電波の受信状況によって画面に表示されるアイコンが変わります。
測位状況
機能切
画面表示
GPS受信状況
非表示
GPSスイッチが「OFF」になっている、
またはエラーが起きている。
測位困難
GPS信号を受信できないため、位置情報が取れない。
空の開けた場所に移動してください。
測位計算中
GPS信号を確認中。しばらくすると位置情報を取得で
きる。測位中になるまでお待ちください。
測位中
GPS信号を受信中。位置情報を取得できる。
測位中
強いGPS信号を受信中。位置情報を取得できる。
• 初めて使う場合やしばらく使わなかった場合は、位置情報を取得できるまで
数十秒から数分かかることがあります。
• GPS受信状況によっては位置情報を取得できないことがあります。
• しばらくの間
が表示されて測位に時間がかかる場合は、GPSスイッチを一度
「OFF」にして、再度「ON」にしてください。
1-6. MM-083基板交換時の注意
地図データ入りMM-083基板 (CX500V/CX520V) にはファクトリーチェックを行わないでください。
ファクトリーチェックを行うと、地図データが消去されてしまいます。
角速度センサ
補修用基板と交換する時，角速度センサ（SE6601）の感度表示を書き留めてください。
Adjust StationからAdjust Manualを起動させて「GYRO sensor sensitivity adj.」を実行させてください。
MM-083 BOARD (SIDE B)
SE6601
YYY
PPP
YYY:
YAW 感度表示
t
PPP:
PITCH 感度表示
G2
t
G1
Note：MM-083基板のSE6601感度表示は補修用基板にのみ記載されています。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-14
JAPANESE
(ENGLISH)
1-7. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX500)
HDR-CX500 (E Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use. Inform a customer of the serial number
change and change the serial number in the repair data.
Note 2:
When replacing the cabinet (bottom) assy for Korea,
affix the “Manufacturing date” label on the specified
location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.
Part No.
A-1738-996-A
HDR-CX500 (Korea Model)
Serial No.
(JAPANESE)
1-7. キャビネット (底) 組立交換時の注意
(HDR-CX500)
* Affix the label
* Manufacturing date
Part No.
A-1738-995-A
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。お客様への案内と修理データのシリアルナン
バー変更を行ってください。
注意2:
Description
CABINET (BOTTOM (CX500-E23))
Korean仕向けキャビネット (底) 組立を交換した際
は，「製造時期」を表すラベルを図の指定位置に
貼り付けてください。
なお，キャビネット (底) 組立には時期表示ラベ
ル，投げ込み(ラベル貼り方)がセットで供給され
ます。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-15
Description
CABINET (BOTTOM (CX500-KR2))
(ENGLISH)
1-8. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX500E)
HDR-CX500E (North European Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Part No.
A-1738-997-A
Description
CABINET (BOTTOM (CX500-CEL))
HDR-CX500E (E, Hong Kong, Tourist Models)
(JAPANESE)
1-8. キャビネット (底) 組立交換時の注意
(HDR-CX500E)
Serial No.
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
Part No.
A-1738-998-A
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。お客様への案内と修理データのシリアルナン
バー変更を行ってください。
Description
CABINET (BOTTOM (CX500-E34))
HDR-CX500E (Chinese Model)
Serial No.
Part No.
A-1739-016-A
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-16
Description
CABINET (BOTTOM (CX500-CN2))
(ENGLISH)
1-9. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX500V)
HDR-CX500V (Japanese Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Note 2:
When replacing the cabinet (bottom) assy for US, affix
the “Manufacturing date” label and the “Factory” label
on the specified location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.
* Affix the label
* Manufacturing date
Part No.
A-1738-990-A
Description
CABINET (BOTTOM (CX500-J1))
HDR-CX500V (US Model)
Note 3:
* Factory
* Manufacturing date
* Affix the label
Serial No.
When replacing the cabinet (bottom) assy for Japanese,
affix the “Manufacturing date” label on the specified
location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.
Part No.
A-1738-992-A
(JAPANESE)
1-9. キャビネット (底) 組立交換時の注意
(HDR-CX500V)
HDR-CX500V (Canadian Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
Serial No.
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。 お客様への案内と修理データのシリアルナン
バー変更を行ってください。
注意2:
US仕向けキャビネット (底) 組立を交換した際は
「製造時期」を表すラベルと，「製造所」を表す
ラベルを図の指定位置に貼り付けてください。
なお，キャビネット (底) 組立には時期表示ラベ
ル，投げ込み(ラベル貼り方)がセットで供給され
ます。
注意3:
Japanese仕向けキャビネット (底) 組立を交換した
際は，「製造時期」を表すラベルを図の指定位置
に貼り付けてください。
なお，キャビネット (底) 組立には時期表示ラベ
ル，投げ込み(ラベル貼り方)がセットで供給され
ます。
Description
CABINET (BOTTOM (CX500-U2))
Part No.
A-1738-993-A
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-17
Description
CABINET (BOTTOM (CX500-CA2))
(ENGLISH)
1-10.PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX500VE)
HDR-CX500VE (Australian Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Part No.
A-1738-994-A
(JAPANESE)
1-10.キャビネット (底) 組立交換時の注意
(HDR-CX500VE)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。お客様への案内と修理データのシリアルナン
バー変更を行ってください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-18
Description
CABINET (BOTTOM (CX500-AU2))
(ENGLISH)
1-11.PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX505VE)
HDR-CX505VE (AEP, UK Models)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Part No.
A-1739-027-A
(JAPANESE)
1-11.キャビネット (底) 組立交換時の注意
(HDR-CX505VE)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。お客様への案内と修理データのシリアルナン
バー変更を行ってください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-19
Description
CABINET (BOTTOM (CX505-CEN))
(ENGLISH)
1-12. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX520)
HDR-CX520 (E Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use. Inform a customer of the serial number
change and change the serial number in the repair data.
Part No.
A-1739-023-A
(JAPANESE)
1-12. キャビネット (底) 組立交換時の注意
(HDR-CX520)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。お客様への案内と修理データのシリアルナン
バー変更を行ってください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-20
Description
CABINET (BOTTOM (CX520-E23))
(ENGLISH)
1-13. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX520E)
HDR-CX520E (North European Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Part No.
A-1739-024-A
Description
CABINET (BOTTOM (CX520-CEL))
HDR-CX520E (E, Tourist Models)
(JAPANESE)
1-13. キャビネット (底) 組立交換時の注意
(HDR-CX520E)
Serial No.
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
Part No.
A-1739-025-A
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。 お客様への案内と修理データのシリアルナン
バー変更を行ってください。
Description
CABINET (BOTTOM (CX520-E34))
HDR-CX520E (Chinese Model)
Serial No.
Part No.
A-1739-026-A
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-21
Description
CABINET (BOTTOM (CX520-CN2))
(ENGLISH)
1-14. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX520V)
HDR-CX520V (Japanese Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Note 2:
When replacing the cabinet (bottom) assy for US, affix
the “Manufacturing date” label and the “Factory” label
on the specified location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.
* Affix the label
* Manufacturing date
Part No.
A-1739-017-A
Description
CABINET (BOTTOM (CX520-J1))
HDR-CX520V (US Model)
Note 3:
* Factory
* Manufacturing date
* Affix the label
Serial No.
When replacing the cabinet (bottom) assy for Japanese,
affix the “Manufacturing date” label on the specified
location as shown in the figure.
The date label and inset (how to affix) are supplied
together with the cabinet (bottom) assy.
Part No.
A-1739-019-A
(JAPANESE)
1-14. キャビネット (底) 組立交換時の注意
(HDR-CX520V)
HDR-CX520V (Canadian Model)
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
Serial No.
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。 お客様への案内と修理データのシリアルナン
バー変更を行ってください。
注意2:
US仕向けキャビネット (底) 組立を交換した際は
「製造時期」を表すラベルと，「製造所」を表す
ラベルを図の指定位置に貼り付けてください。
なお，キャビネット (底) 組立には時期表示ラベ
ル，投げ込み(ラベル貼り方)がセットで供給され
ます。
注意3:
Japanese仕向けキャビネット (底) 組立を交換した
際は，「製造時期」を表すラベルを図の指定位置
に貼り付けてください。
なお，キャビネット (底) 組立には時期表示ラベ
ル，投げ込み(ラベル貼り方)がセットで供給され
ます。
Description
CABINET (BOTTOM (CX520-U2))
Part No.
A-1739-020-A
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-22
Description
CABINET (BOTTOM (CX520-CA2))
(ENGLISH)
1-15. PRECAUTION ON REPLACING
THE CABINET (BOTTOM) ASSY
(HDR-CX520VE)
HDR-CX520VE (Australian Model)
Serial No.
The model display adopts the laser printing method.Therefore, the
cabinet (bottom) assy for replacement differs depending on the
destination.
As similar displays are provided, choose the suitable one for order.
Note 1:
After replacing the cabinet (bottom) assy, the serial
number for it will be changed to the one exclusive for
service use.
Inform a customer of the serial number change and
change the serial number in the repair data.
Part No.
A-1739-022-A
Description
CABINET (BOTTOM (CX520-AU2))
HDR-CX520VE (AEP, UK Models)
(JAPANESE)
1-15. キャビネット (底) 組立交換時の注意
(HDR-CX520VE)
Serial No.
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のキャビネット (底) 組立は仕向けにより異
なります。類似の表示もありますので，該当するものを選
んで注文して下さい。
注意1: キャビネット (底) 組立交換後はシリアルナンバー
がサービス専用のシリアルナンバーに変更されま
す。 お客様への案内と修理データのシリアルナン
バー変更を行ってください。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1-23E
Part No.
A-1739-021-A
Description
CABINET (BOTTOM (CX520-CEN))
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF THE ST-217 BOARD’S CHARGING CAPACITOR (C5008)
The charging capacitor (C5008) of the ST-217 board is charged
up to the maximum 315 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
ST-217 Board
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 kΩ/1 W
R:1 kΩ /1 W
(Part code:
1-215-869-11)
Wrap insulating tape.
C5008
(Charging Capacitor)
ST-217 Board
C5008
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-1
2-1. IDENTIFYING PARTS
Cabinet (Top) Section
• FP-1131 Flexible Board
BT Panel Section
Cabinet (L) Assy
Front Panel Section
• FP-1121 Flexible Board
Lens/Main Block
• GP317 Assy
• ST-217 Board
• FP-1120 Flexible Board
• FP-1123 Flexible Board
• FP-1126 Flexible Board
• MM-083 Board
• FP-1122 Flexible Board
• VC-575 Board
• FP-1124 Flexible Board
• FP-1021 Flexible Board
• CM-103 Board
Cabinet (R) Section
• PD-389 Board
• CK-217 Board
• FP-1127 Flexible Board
• FP-1128 Flexible Board
- DISASSEMBLY FLOW 2-2-1. OVERALL SECTION
Cabinet (Bottom) Block
- Cabinet (Bottom) Block
- Remote Control Window
- Cabinet (L) Assy
2-2-2. FRONT PANEL SECTION
- GP317 Block
- F Panel Block
2-2-3. CABINET (TOP/R) SECTION
- Cabinet (R) Section
- Cabinet (Top) Block
- BT Panel Section
2-2-4.LENS SECTION
- FP-1123 Block
- MM-083 Board Block
- VC-575 Section
2-2-6. CABINET (R) SECTION
- PD-389 Board
- FTS Block
2-2-7. HINGE SECTION
2-2-5. VC-575 SECTION
- FP-1122 Block
- VC-575 Board Block
- CK-217 Board Block
- Hinge Assy
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1 Cabinet (Bottom) Block (1-1 to 1-2)
2 Remote Control Window (2-1 to 2-2)
3 Cabinet (L) Assy (3-1 to 3-8)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points
with the short jig about 10 seconds.
ST-217 Board
3-5 (#2)
3-4 (#2)
3-7
(Claw)
3-3
(Open)
R:1 kΩ /1 W
(Part code:
1-215-869-11)
C5008
(Charging Capacitor)
3-6
(#2)
3-8E
(Claw)
HELP01
3-1
(#2)
Front Panel
Section
3 Cabinet (L) Assy
(See Page 2-4)
3-2
(#2)
2-2E (Claw)
2 Remote Control Window
1-2E (Claw)
2-1 (#1)
1 Cabinet (Bottom) Block
1-1 (#1)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-3
2-2-2. FRONT PANEL SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 GP317 Block (1-1 to 1-3)
2 F Panel Block (2-1 to 2-9)
2 F Panel Block
2-1
HELP03
HELP04
HELP02
2-2 (#2)
Cabinet (Top/R)
Section
(See Page 2-5)
2-3 (#2)
2-5 (#12)
1-2 (#3)
1-3E (Claw)
1-1
HDR-CX500V/CX500VE/CX505VE/
CX520V/CX520VE
1 GP317 Block
Note: GP317 Assy (GP-026) 交換時は，1-14ペー
ジ「1-5. GPS 受信確認」を必ずお読み
ください。
2-4
(Open)
Note: Be sure to read “1-5. GPS RECEIVING
CHECK” on page 1-7 when you exchange
the GP317 Assy (GP-026).
2-6
HELP05
2-7
HELP05
2-8
2-9E
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-4
2-2-3. CABINET (TOP/R) SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Cabinet (R) Section (1-1 to 1-5)
2 Cabinet (Top) Section (2-1 to 2-13)
3 BT Panel Section (3-1 to 3-3)
2-1 (#2)
2-4
2 Cabinet (Top) Section
2-2 (#2)
2-8 (#1)
2-3 (Claw)
HELP06
3 BT Panel Section
2-13E
(Boss)
2-6
2-5
2-9 (#11)
HELP08
2-7
3-3E
(#1)
2-12
(Boss)
3-2
3-1
HELP07
2-11
(#2)
1-3
(#2)
1-2
(#2)
Lens
Section
(See Page 2-6)
2-10 (#1)
1-5E
(#2)
1-4
1-1
1 Cabinet (R) Section
(See Page 2-8)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-5
2-2-4. LENS SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 FP-1123 Block (1-1 to 1-6)
2 MM-083 Board Block (2-1 to 2-2)
3 VC-575 Section (3-1 to 3-7)
2 MM-083 Board Block
1-2 (#3)
1-3
HELP09
1-1
1 FP-1123 Block
ard
7
-21
ST
Bo
1-6E (#1)
2-2E (#1)
MM
-08
3
1-4
1-5 (Bosses)
3-3 (#1)
HELP10
3-1
3-4 (#1)
HELP11
3-2 (#2)
3-7E
HELP12
3-5 (#1)
3-6
3 VC-575 Section
(See Page 2-7)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-6
2-1
2-2-5. VC-575 SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 FP-1122 Block (1-1 to 1-3)
2 VC-575 Board Block (2-1 to 2-7)
1-1 (#2)
1-2
1 FP-1122 Block
1-3E
2-1 (#3)
HELP13
2-4
2-5 (#3)
2-6
(#3)
2 VC-575 Board Block
5
57
VC
HELP14
2-2 (Claw)
2-7E
2-3 (Boss)
HELP15
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-7
2-2-6. CABINET (R) SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 PD-389 Board (1-1 to 1-15)
2 FTS Block (2-1 to 2-11)
2-6
1 PD-389 Board
Hinge Section
2-4 (Claws)
(See Page 2-9)
2-2
1-14
(#3)
1-10
(Claws)
PD
-38
1-9
(#3)
9
2-3 (#3)
2-1
(Claw)
1-12
1-15E
(Claw)
1-8
HELP16
1-7
1-11
1-5
(Claws)
1-2
(#2)
1-13
2-5
1-6
2-10 (Claws)
2 FTS Block
1-1
1-3
2-9 (Claws)
2-11E
1-4
(#2)
2-8 (Solder)
2-7
HELP17
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-8
2-2-7. HINGE SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
1 CK-217 Board Block (1-1 to 1-5)
2 Hinge Assy (2-1 to 2-9)
1-1
1-3
(#3)
HELP18
1-5E
HELP18
1-4
1-2
1 CK-217 Board Block
2-6
(#1)
2-3 (#1)
2-5
2-4
2 Hinge Assy
2-8
2-9E
HELP19
2-2
(#1)
2-1
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
2-9E
2-7
HARDWARE LIST
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
HELP01
CM SHIELD SHEET PUTTING POSITION
Rib
Rib
CM Shield Sheet
HELP02
THE METHOD OF ATTACHMENT OF LENS BARRIER UNIT FLEXIBLE CABLE
Lens Barrier Unit
Mountain Fold
Ribs
Ribs
Lens Barrier Unit Flexible Cable
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
HELP03
HELP04
HOW TO FOLD FLASH UNIT FLEXIBLE CABLE
AND ST SHIELD SHEET PUTTING POSITION
HOW TO FOLD FP-1121 FLEXIBLE BOARD
FP-1121 Flexible Board
Valley Fold
Flash Unit
Valley Fold
Valley Fold
ST Shield Sheet
HELP05
THE METHOD OF ATTACHMENT OF LENS BARRIER UNIT FLEXIBLE CABLE AND
FP-1121 FLEXIBLE BOARD
Lens Barrier Unit
Flexible Cable
F Cabinet
VC Bottom
Frame
FP-1121
Flexible Board
Valley Fold
Mountain Fold
Tape (AS 1/2)
HELP06
HOW TO FOLD AND THE METHOD OF ATTACHMENT OF MICROPHONE UNIT FLEXIBLE CABLE
Microphone Unit Flexible Cable
Microphone Unit Flexible Cable
Mountain Fold
Rib
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
HELP07
HELP08
HOW TO FOLD OF MICROPHONE UNIT
FLEXIBLE CABLE AND FP-1131 FLEXIBLE
BOARD
THE METHOD OF ATTACHMENT OF
DC JACK CABLE
Microphone Unit Flexible Cable
Ribs
Valley Fold
Ribs
FP-1131 Flexible Board
HELP09
DC Jack
HELP10
HOW TO FOLD OF FP-1120 FLEXIBLE
BOARD
FP-1120 Flexible Board
HOW TO FOLD OF FP-1123 FLEXIBLE
BOARD
FP-1123 Flexible Board
Mountain Fold
Mountain Fold
HELP11
RADIATION SHEET (CM) PUTTING POSITION AND CM SHIELD SHEET
Radiation Sheet (CM)
FP-1124
Flexible Board
CM Shield Sheet
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
HELP12
THE METHOD OF ATTACHMENT OF LENS FLEXIBLE BOARD
Mountain
Fold
Lens Flexible Board
Lens Flexible
Board
HELP13
HELP14
VC RADIATION SHEET (A) AND VC RADIATION
SHEET (B) PUTTING POSITION
VC Heat Sink
VC Radiation Sheet (A)
Scratched line
VC RADIATION SHEET (A)
PUTTING POSITION
VC-575 Board
VC Radiation Sheet (B)
VC Radiation Sheet (A)
IC
HELP15
FUSE LABEL PUTTING POSITION
Fuse Label
VC Bottom Frame
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
HELP16
HOW TO FOLD AND THE METHOD OF ATTACHMENT OF FP-1128 FLEXIBLE BOARD
AND LCD FLEXIBLE GUARD SHEET PUTTING POSITION
Mountain Fold
LCD Flexible Guard Sheet
FP-1128 Flexible Board
HELP17
HELP18
LCD CUSHION PUTTING POSITION
Back Light Frame
THE METHOD OF ATTACHMENT OF SPEAKER HARNESS
AND HOW TO FOLD FP-1127 FLEXIBLE BOARD
Speaker Harness
Valley Fold
LCD Cushion
FP-1127 Flexible Board
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
HELP19
THE METHOD OF ATTACHMENT OF FP-1128 FLEXIBLE BOARD
1 Fold dotted line parts of the FP-1128 flexible board as shown in figure.
Adhesive tape
Mountain Fold
Valley Fold
Adhesive tape
Adhesive tape
Adhesive tape
Adhesive tape
Valley Fold
Mountain Fold
Stick it together in the adhesive tape
while bending the FP-1128 flexible board.
Adhesive
tape
Boss
Boss
LCD Flexible Clamp
2 Install the LCD flexible clamp and the FP-1128 flexible
board in the hinge assy as shown in figure.
2 times
3 Roll the FP-1128 flexible board 2 times
in the hinge assy as shown in figure.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/4)
OVERALL BLOCK DIAGRAM (4/4)
OVERALL BLOCK DIAGRAM (2/4)
POWER BLOCK DIAGRAM (1/2)
OVERALL BLOCK DIAGRAM (3/4)
POWER BLOCK DIAGRAM (2/2)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
CM-103 BOARD
FP-1124
FLEXIBLE
BOARD
VC-575 BOARD (1/3)
INCK
N11
XCLR
N4
2
44
3
43
PLL/IO/EMC/
DDR/PCI/ATA/IMG
(11/15 - 14/15)
SENS_DATA_P_0/M_0 - SENS_DATA_P_7/M_7
SENSSCK, SENSSO, SENSXCS
SENS_VD, SENS_HD
CLK_CMOS_IN
4
XFLASH_RST
2
IC7505
4-6
SHUTTER_XA
SHUTTER_XA
1-3
SHUTTER_A
SHUTTER_A
M
ZOOM MR
SENSOR
F_MR_A, F_MR_B
ZOOM_A, ZOOM_B,
ZOOM_XA, ZOOM_XB
Z_MR_A, Z_MR_B
M
LENS TEMP
SENSOR
IRIS PI
SENSOR
IRIS
MOTOR
M
NF_DRIVE±
L_TEMP_OUT
32
IRIS_A, IRIS_B,
IRIS_XA, IRIS_XB
ND_BIAS±
ND_HALL±
T_TEMP_OUT
PITCH±
PITCH_HALL±
YAW MOTOR
HALL
ELEMENT
YAW±
YAW_HALL±
YAW_HALLBIAS±
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
X7501
60MHz
EMC_XWE
EMC_XRAS
EMC_XOE
EMC_RDY0
EMC_INT
EMC_XCS_0
EMC_CLK_OUT_FLASH
F_XRP
EMC_XOE
EMC_RDY0
EMC_INT
EMC_XCS_0
EMC_CLK_OUT_FLASH
EMC_CLK_IN_FLASH
A_1.8V
R8103
ONENAND
(15/15)
E8
R8106
3
6
OVERALL (2/4)
(PAGE 3-2)
CN1003
LENS_COVER_DIR_PWM
LENSV_EN
USB_D±
ND_HALL±
USB_D±
USB_ID2
MT_5.0V
FOCUS±
ZOOM_A,ZOOM_B,
ZOOM_XA, ZOOM_XB
1
4
3
OVC_DET
IC1005
Z_MR_A, Z_MR_B
MD_IN4A
XRST_IC_5201
C7
IC_5501_IC5201_CLK
B8
F11
USB_ID2
USB_VBUS_LIMIT
2
IC1006
(1/15)
5
(USB)
SWITCHING
USB_VCC
1
IC1004
(1/15)
(1/15)
Z_MR_A, Z_MR_B
4
Q1008
XCAM_SCK
CAM_SO
CAM_SI
XCS_IC_5201
IC_5201_VD
F_MR_A, F_MR_B
F_MR_A, F_MR_B
4
Q1006
1
2
7
6
5
3
SWITCHING
NF_DRIVE±
LENS_TEMP_AD
XIRIS_RST_LED
SWITCH
FOCUS±
THERM
PITCH_HALLBIAS±
YAW±
IC_5501_IC5201_CLK
E9
XRST_IC_5501_CPU
E7
STEADYSHOT
IC_5501_INT_REQ
PROCESSOR
IRIS_DIR_B
(10/15)
IRIS_DIR_A
IRIS_ENB
ZM_DIR_B
ZM_DIR_A
ZM_ENB
IR_FILTER_EN
IR_FILTER_DIR
CAM_V
XCS_IC_5501
IC_5501_SO
IC_5501_SI
IC_5501_SCK
YAW_HALLBIAS±
USB
DETECT
R1028
PITCH±
PITCH_HALL±
PITCH_HALLBIAS±
CN1008
CAM_UART_TXD
1
CAM_UART_RXD
2
CPC_CS
3
BOOT_MODE_PORT1
8
UART0_SI
10
UART0_SO
11
UART1_SI
12
UART1_SO
13
IC_5501_SI
IC_5501_SO
IC_5501_SCK
YAW±
IC_5501_SO, IC_5501_SI, IC_5501_SCK
YAW_HALL±
Q1007
AC3
B9
IC5501
ZOOM_A,ZOOM_B,
ZOOM_XA, ZOOM_XB
PITCH_HALL±
XVBUS_DET
D_2.8V
Q1001
STEPPERIRIS_A, STEPPERIRIS_B,
STEPPERIRIS_XA, STEPPERIRIS_XB
PITCH±
VBUS_EN
LENS_TEMP_AD
IRIS_SENS
XIRIS_RST_LED
THERM
NF_DRIVE±
PITCH_HALLBIAS±
M
IC8101
(2/2)
XFLASH_RST
ND_BIAS±
STEPPERIRIS_A, STEPPERIRIS_B,
STEPPERIRIS_XA, STEPPERIRIS_XB
11, 10 12, 13 17 - 20 8, 9 15, 14 21 - 24
HALL
ELEMENT
EMC_XWE
EMC_XRAS
ND_DRIVE±
ND_DRIVE±
IR_PI_C
IRIS_SENS
50
IR_PI_A
IR_PI_A
51
R1003
PITCH MOTOR
M
R8102
AC2
IC5201
OPTICAL IMAGE
STABILIZER
OIS TEMP
SENSOR
EMC_CKE
EMC_XCAS
EMC_XCS_1
EMC_CLK_OUT_SDRAM
EMC_CKE
EMC_XCAS
EMC_XCS_1
EMC_CLK_OUT_SDRAM
EMC_CLK_IN_SDRAM
EMC_XWE
EMC_XRAS
ZOOM AND FOCUS
DRIVE
MD_IN4B
NF MOTOR
25, 26
ZOOM MOTOR
FOCUS±
30, 31 28, 27 46, 44 45, 43 42, 48
ND_HALL±
35, 34 1 - 4
ND_DRIVE±
37 - 40
FOCUS MR
SENSOR
EMC_ADDR_0 - EMC_ADDR_15
(9/15)
FOCUS MOTOR
M
SDRAM
(15/15)
EMC_ADDR_0 - EMC_ADDR_12,
EMC_ADDR_14, EMC_ADDR_15
CN1010
ND_BIAS±
H
IC8101
(1/2)
EMC_DATA_0 - EMC_DATA_31
EMC_ADDR_0 - EMC_ADDR_15
LENS BLOCK (2/2)
ND FILTER MOTOR
M
EMC_DATA_0 - EMC_DATA_31
EMC_DATA_0 - EMC_DATA_15
CN1011
LENS
BARRIER
UNIT
EMC_DQM_0 - EMC_DQM_3
SENS_CLK_P, SENS_CLK_M
BUFFER
(11/15)
A : VIDEO SIGNAL
EMC_DQM_0 - EMC_DQM_3
3, 2
DCKP, DCKM
IC7501
(1/3)
H3, M3
XVS, XHS
37, 39 40, 38, 41 34, 33, 31, 30, 28, 27, 25, 24, 19, 18, 16, 15, 13, 12, 10, 9
N5, M5
SCK, IC_7501_SDO, XCE
22, 21
IRIS
(SHUTTER)
6, 8, 5 12, 13, 15, 16, 18, 19, 21, 22, 27, 28, 30, 31, 33, 34, 36, 37
IC6804
CMOS IMAGER
9, 7
LENS BLOCK (1/2)
CN1002
24, 25
CN6801
10M_DOAP, 10M_DOAM, 10M_DOBP,
10M_DOBM, 10M_DOCP, 10M_DOCM,
10M_DODP, 10M_DODM, 10M_DOEP,
10M_DOEM, 10M_DOFP, 10M_DOFM,
10M_DOGP, 10M_DOGM, 10M_DOHP,
10M_DOHM
YAW_HALL±
E8
YAW_HALLBIAS±
XSYS_RST
VREF_GYRO
YAW_AD
PITCH_AD
VST_C_RESET_PITCH
G5
VST_C_RESET_YAW
K1
08
3-1
1
OVERALL (2/4)
(PAGE 3-2)
2
OVERALL (3/4)
(PAGE 3-3)
4
5
6
CPC
(For check)
3-2. OVERALL BLOCK DIAGRAM (2/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-575 BOARD (2/3)
PLL/IO/EMC/
DDR/PCI/ATA/IMG
(11/15 - 14/15)
L2
IC4901
L3
LANC INTERFACE,
HI PROCESSOR
(8/15)
E9
BB_SO
XBB_SCK
XRESET_REQ
XFR_SCK
FR_SI
FR_SO
XCS_FRONT
XRESET_REQ
Q4902
D_2.8V
4
SYSTEM_AD
XGPS_RST
H11
GSP_FIRMUP
AN4
R1021 *1
R1022 *2
A1, B1
C1, D1
ADA_LRCK
ADA_BCK
ADA_FCK
ADA_SIA0
ADA_SOA0
ADA_SOA1
XCS_IC_2801
SYS_SOUND
XNTSCPALDET
SWITCHING
XCHARG_LED
XCAM_LED
*1 R1021
0
CX505VE
XX EXCEPT CX505VE
*2 R1022
0 EXCEPT CX505VE
XX CX505VE
M5
L3
M2
K2
L1
J1
C2
D2
JACK_AD
XSYS_RST
XSYS_RST
OVERALL (3/4)
(PAGE 3-3)
6
XFLASH_RST
1
3
OVERALL (1/4)
(PAGE 3-1)
SP+/–
INT_MIC_L
INT_MIC_R
INT_MIC_F
SHOE_MIC_FL
SHOE_MIC_FR
5
OVERALL (3/4)
(PAGE 3-3)
8
4
41
40
19
20
7
CN1007
VIDEO/D3_PR
8
S_C/D3_PB
9
S_Y/D3_Y
10
AUDIO_L_I/O
1
AUDIO_R_I/O
2
JACK_AD
4
LANC_SIG
3
VIDEO/D3_PR
S_C/D3_PB
S_Y/D3_Y
AUDIO_L_I/O
AUDIO_R_I/O
C2
D2
AP4
XSYS_RST
OVERALL (1/4)
(PAGE 3-1)
SP+
SP−
10
FP-1123
FLEXIBLE BOARD
SHOE_ON
B8
PANEL_O/C
8
FP-1127 FLEXIBLE
TO
CK-217 BOARD
OVERALL (4/4)
(PAGE 3-4)
IC2801
AUDIO/VIDEO
PROCESSOR
(4/15)
LINEOUT_Y
LINEOUT_PB
LINEOUT_PR
CX500V/CX500VE/CX505VE/CX520V/CX520VE
A8
SWITCH
BB_SO
XBB_SCK
BL_H
BL_L
FR_XRESET
XBB_SCK
BB_SO
NTSCXPALDET
OVERALL (3/4)
(PAGE 3-3)
XPANEL_POWER_ON
SWITCH
GPS_SW_ON/OFF
XPOWER_TACT_SW
XPANEL_POWER_ON
GPS_SW_ON/OFF
XPOWER_TACT_SW
44
42
38
37
35
12
15
17
16
5
Q1005
Q7501
TP_SEL2
X4901
32.768kHz
XBB_RST
XCS_LCD
LCD_HS
LCD_VS
LCD_CLK_OUT
PANEL_NOR/REV
TP_X
TP_Y
TP_SEL1
KEY_AD2
XBB_RST
XCS_LCD
LCD_HS
E34
LCD_VS
E35
LCD_CLK_OUT
D35
PANEL_NOR/REV
TP_X
TP_Y
TP_SEL1
KEY_AD2
F14
2, 1
IC7501
(2/3)
26 - 33
CN1009
LCD_PDB0 - LCD_PDB7
K11
CN1010
VIDEO_I/O
9
S_C_I/O
5
S_Y_I/O
10
AUDIO_L
1
AUDIO_R
6
MULTI_JACK_IN
7
LANC_SIG
2
A/V R
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A11
A10
A9
B10
B9
XMS_IN
SHOE_ON
Q4604
Q4702
BL_H
XSYS_RST
SWITCHING
IC4701
BL_L
K2
FR_EVER_SI
FR_EVER_SO
FR_EVER_SCK
XCS_DD
XLANC_PWR_ON
XLANC_ON
LANC_IN
LANC_OUT
VTR_DD_ON
LDO_ON
FR_XRESET
DC/DC CONVERTER,
LANC DRIVE
(7/15)
LANC_SIG
7
OVERALL (3/4)
(PAGE 3-3)
SHOE
DETECT
SWITCH
LANC_SIG
Q4605
SHOE_UNREG
SHOE
POWER
SWITCH
DC JACK
ACV_UNREG
Q4603
ACV_ON
M2
BATT_ON
VTR_UNREG, VTR2_UNREG, I/O_MT_UNREG, ST_UNREG
ACV/BATT
SELECT
Q4601,
Q4602
CN1004
ACV_UNREG_CN
2
BATT/XEXT_CN
3
ACV_GND
1
D4604
BATT_UNREG_CN
BATT_SIG
Q4901
BUFFER
BATT_SIG
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
3-2
J901
DC IN
SWITCH
BATT_UNREG
INIT_CHARGE_ON
BATT/XEXT_CN
ACV_UNREG
BATT/XEXT
ACV_GND
BATT_GND
4
5
6
BATT_UNREG
BATT_SIG
BATT_GND
+
C
–
BH901
BATTERY
TERMINAL
BOARD
(
)
3-3. OVERALL BLOCK DIAGRAM (3/4)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-575 BOARD (3/3)
FP-1122 FLEXIBLE BOARD
CN1001
XPHOTO_LED
11
XSTART/STOP
13
KEY_AD1
15
LANC_SIG
16
XSTRB_FULL
17
STRB_CHARGE
19
STROBE_ON
21
EXT_STROBE_ON
23
HOTSHOE_ID1
25
HOTSHOE_ID2
27
UART3_SI
40
GPS_BUF_CNTL
41
UART3_SO
42
VST_C_RESET_R
46
XSYS_RST
47
ZOOM_VR_AD
53
ROLL_AD
57
FP-1120 FLEXIBLE
TO
ST-217 BOARD
OVERALL (4/4)
(PAGE 3-4)
OVERALL (2/4)
(PAGE 3-2)
DE_HDMI, HSYNC_HDMI, VSYNC_HDMI,
64FS_HDMI, I2SO_HDMI, FS_HDMI
PLL/IO/EMC/
DDR/PCI/ATA/IMG
AJ35
g
IC6503
SIRCS
RECEIVER
SIRCS_SIG
NS_LED_A
F_TALLY_LED
D6502
(TALLY)
TALLY_VDD
8
7
IC2201
PCI PROCESSOR
(2/15)
1
2
CLK_SYS_OUT
Y2
4
OVERALL (2/4)
(PAGE 3-2)
CN1001
TMDS_DATA2_+
2
TMDS_DATA2_3
TMDS_DATA1_+
5
TMDS_DATA1_6
TMDS_DATA0_+
8
TMDS_DATA0_9
TMDS_CLOCK_+
11
TMDS_CLOCK_12
SDA
22
SCL
SCL
21
CEC 19 CEC
SDA
16
SCL
15
CEC
14
HPD
HPD
19
IC2301
DDR SDRAM
(3/15)
IC_2301_A00 - IC_2301_A13
XIC_2301_CLK, IC_2301_CLK,
XIC_2301_CS0, XIC_2301_RAS,
XIC_2301_CAS, XIC_2301_WE,
IC_2301_CKE1, IC_2301_BA0,
IC_2301_BA1
PCI_XBE0 - PCI_XBE3
PCI_PAR
PCI_XFRM
PCI_XTRDY
PCI_XDEVSEL
PCI_XPERR
PCI_XSTOP
PCI_XIRDY
PCI_CLK
OVERALL (2/4)
(PAGE 3-2)
CN1012
SIRCS_SIG
IR_LED_ON
NS_LED_K
D_2.8V
HPD
A_2.8V
PCI_AD0 - PCI_AD31
R1014, R1015
IC_2301_D00 - IC_2301_D31
25
HDMI
IC_2301_DQS0 - IC_2301_DQS3,
IC_2301_DQM0 - IC_2301_DQM3
AC12
X7504
12MHz
5
Q3501
LEVEL SHIFT
HDMI_JACK_IN
SPDIF_O_TX
LANC_SIG
XSYS_RST
7
SHOE_MIC_FL
SHOE_MIC_FR
INT_MIC_L
INT_MIC_R
INT_MIC_F
NS_LED_A
E6
SPDIF_O_TX
Q1002
SWITCH
NS_LED_K
D6503
(NIGHTSHOT)
6
E1
TMDS_DATA2+
TMDS_DATA2TMDS_DATA1+
TMDS_DATA1TMDS_DATA0+
TMDS_DATA0TMDS_CLOCK+
TMDS_CLOCK-
SDA
FP-1121 FLEXIBLE BOARD
(REMOTE SENSOR)
IDCK
I2C_SDA
I2C_SCK
CEC_SAMP_CLK
(11/15 - 14/15) AR31
XCHARGE_LED
12
XCAM_LED
14
XGPS_RST
37
GPS_FIRMUP
39
20
36
24
28
32
IC3501
HDMI TRANSMITTER
(5/15)
C3
PCI_XREQFS0
PCI_XGNTTS0
PCI_XINTA
PCI_XRESET
H1
CODEC_VDATA_0 - CODEC_VDATA_7
CODEC_FLD, CODEC_VCLK,
CODEC_MCK_OUT, CODEC_LRCK_OUT
XTALLY_LED
CODEC_ADATA0, CODEC_ADATA1
D_2.8V
T13
3
4
CODEC_SYSCLK
IC7502
LEVEL SHIFT
(13/15)
CODEC_VCLKR_IN
AC13
AC5
CN1005
MMC_BIO0 - MMC_BIO7
MMC_CMD
28
MMC_CLK
30
OVERALL (1/4)
(PAGE 3-1)
VST_C_RESET_PITCH
VST_C_RESET_YAW
PITCH_AD
YAW_AD
VREF_GYRO
2
XMS_ACC_LED
MM-083 BOARD
FP-1126
FLEXIBLE
BOARD
19 - 26
P11
CODEC_SYSCLK_BA
CN7301
19 - 26
9
D0_HDMI - D15_HDMI
IC7501
(3/3)
CN1006
TMDS_DATA2+
3
TMDS_DATA25
TMDS_DATA1+
7
TMDS_DATA19
TMDS_DATA0+
11
TMDS_DATA013
TMDS_CLOCK+
15
TMDS_CLOCK17
SDIF_DATA_0 - SDIF_DATA_7
SDIF_CMD
28
SDIF_CLK
30
36
37
38
39
40
36
37
38
39
40
6
6
VST_C_RESET_P
VST_C_RESET_Y
PITCH_AD
YAW_AD
VREF_GYRO
XMS_ACC_LED
SE6601
PITCH/YAW
D7301
(MS ACCESS)
SDIF_DATA_0 - SDIF_DATA_7
SDIF_CMD
SDIF_CLK
IC8701
32GB MEMORY
(3/4)
SDIF_DATA_0 - SDIF_DATA_7
SDIF_CMD
SDIF_CLK
IC8801
32GB MEMORY
(4/4)
CONTROL SWITCH BLOCK
(RS31700)
CX520/CX520E/CX520V/CX520VE
CN7302
DIAL_A
43
DIAL_B
44
KEY_AD3
42
DIAL_A
43
DIAL_B
44
XPON_SW
42
6
5
4
S001 - S003
MANUAL,
AUTO SWITCH
OVERALL (2/4)
(PAGE 3-2)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
08
3-3
MSX_BS
16
MSX_CLK
8
XMS_IN
12
6
MSX_BS
16
MSX_CLK
8
XMS_IN
12
4, 3, 5, 7
14, 15, 13, 11
MSX_BIO0 - MSX_BIO3
14, 15, 13, 11
CN7303
MS_DATA0 - MS_DATA3
MS_BS
MS_SCLK
XMS_IN
2
8
6
MEMORY
STICK
PRO DUO
Ver. 1.1 2009.12
The changed portions from
Ver. 1.0 are shown in blue.
XBB_RST
BB_SO
XBB_SCK
XCS_LCD
LCD_HS
LCD_VS
LCD_CLK_OUT
XBB_RST
PANEL_SO
LCD_SCK
XCS_LCD
LCD_HS
LCD_VS
LCD_CLK_OUT
PANEL_NOR/REV
PANEL_NOR/REV
BL_H
BL_L
BL_H
19
BL_L
20
8
FP-1127 FLEXIBLE
TO
VC-575 BOARD
OVERALL (2/4)
(PAGE 3-2)
TP_X
TP_Y
TP_X
15
TP_Y
17
16
TP_SEL1
TP_SEL1
34
31
30
32
28
27
25
2
5
6
4
8
9
11
2
34
9
11
BL_H
27
BL_L
25
BL +
45
BL –
44
5
7
TP_X
31
TP_Y
29
CN6403
TP_YU
4
TP_XL
1
6
30
LCD_D0 - LCD_D7
XBB_RST
PANEL_SO
LCD_SCK
XCS_LCD
LCD_HS
LCD_VS
LCD_CLK_OUT
4
5
PANEL_O/C
PANEL_NOR/REV
TP_SEL1
3
5
6
4
7
8
9
47
TP_XR
TP_YL
CN5804
XPOWER_TACT_SW
5
PLAY_SW
3
DISC_BURN_SW
2
NIGHTSHOT_SW
4
7
8
GPS_SW_ON/OFF
(
53
TOUCH
PANEL
12
2
5
11
9
FP-1120 FLEXIBLE
TO
VC-575 BOARD
OVERALL (3/4)
(PAGE 3-3)
SK31700 FLEXIBLE BOARD
S001 - S004
POWER,
VIEW IMAGES,
NIGHTSHOT,
DISCBURN
CONTROL SWITCH BLOCK (PS31700)
CN4006
XSTART/STOP
2
PHOTO_REC
10
PHOTO_FREEZE
11
XMODE_SW
8
14
ZOOM_VR_AD
ZOOM_VR
XCHARGE_LED
XCHARGE_LED
XPHOTO_LED
XPHOTO_LED
XCAM_LED
XCAM_LED
S101 - S104
START/STOP, MODE,
SHUTTER, FOCUS
12
4
6
7
IC4001
BUFFER
(1/3)
ON
ROLL_AD
57
VST_C_RESET_R
46
EXT_STROBE_ON
23
HOTSHOE_ID1
25
HOTSHOE_ID2
27
LANC_SIG
16
SP901
(SPEAKER)
08
20
36
24
28
32
A : VIDEO SIGNAL
A : AUDIO SIGNAL
4
MIC901
(MICROPHONE
)
UNIT
6
2
FP-1131
FLEXIBLE
BOARD
CN901
HOT
SHOE
SHOE_MIC_FL
SHOE_MIC_FR
INT_MIC_L
INT_MIC_R
INT_MIC_F
CN4002
INT_MIC_L
INT_MIC_R
INT_MIC_F
CN4004
SHOE_MIC_FL
SHOE_MIC_FR
MIC_FL
14
MIC_FR
15
3
2
STROBE
6
ID1
10
ID2
7
LANC
5
EXT_STOROBE_ON
11
HOTSHOE_ID1
7
HOTSHOE_ID2
10
LANC_SIG
12
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
3-4
ZOOM_VR
W
T
XCHARGE_LED
D101
CHG
XPHOTO_LED
D102
(STILL)
XCAM_LED
D103
(MOVIE)
CX500V/CX500VE/CX505VE/CX520V/CX520VE
GPS_FIRMUP
39
XGPS_RST
37
1, 2
10 - 12
SWITCH
5
FP-1021 FLEXIBLE BOARD
CN4003
S5802
GPS
SP+/-
XE_K
FLASH
UNIT
)
Q5002
UART3_SI_BUFF
40
UART3_SO_BUFF
42
GPS_BUF_CNTL
41
n
TRIGER
C5008
CHARGING
CAPACITOR
RV101
(ZOOM)
LCD
BACKLIGHT
CN5803
2, 1
5
D_2.8V
CX500V/CX500VE/CX505VE/CX520V/CX520VE
SP+/-
FLASH
SWITCH
R5018
4
1
XSTART/STOP
13
KEY_AD1
15
RESET
OFF
3
FLASH
CHARGE
CONTROL
6
(2/3)
ST_UNREG
S5801
FR_XRESET
IC5001
Q5003
PANEL
NOR/REV
TOUCH
PANEL
I/F
2
+
XSYS_RST
3.0 inch
WIDE
COLOR
LCD
UNIT
Q6401, Q6402
PANEL
OPEN/CLOSE
XPOWER_TACT_SW
KEY_AD2
XRESET
SI
SCLK
XCS
XHD
XVD
DCK
SE6401
SE5801
10
ST_UNREG
CN4001
STRB_CHARGE
19
XSTRB_FULL
17
STROBE_ON
21
CN6402
20 - 13
LCD_D0 - LCD_D7
FLASH UNIT (FL31700)
CN5001
XE_A
D5002
L5001
LCD901
CN6401
16 - 23
26 - 33
12
LCD_PD80 - LCD_PD87
ST-217 BOARD
T5001
CN5802
CN5801
44
41
40
42
38
37
35
PD-389 BOARD
6, 7
FP-1128
FLEXIBLE
BOARD
1-3
CK-217 BOARD
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
17 - 10
3-4. OVERALL BLOCK DIAGRAM (4/4)
IC9001
SE9001
30.8kHz
ROLL
DRIVE
(3/3)
UART0_SI
UART0_SO
TX
RX
UPDATA
RESET
5
2
6
1
SI
SO
F/U
X_RST
SI
SO
F/U
X_RST
2
5
1
6
GP317
ASSY
(GP-026)
3-5. POWER BLOCK DIAGRAM (1/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-1122 FLEXIBLE BOARD
ACV_UNREG
)
C
−
4
BATT_SIG
5
BATT_GND
6
VTR2_UNREG
F4608
ST_UNREG
BATT_UNREG_CN
4
BATT_UNREG
ACV_ON
CN1007
LANC_DC
LANC_DC
J2 ACV_ON
K2 BATT_ON
PVDD1a
PVDD1b
LX1a
LX1b
IN1 L11
L4701
PVDD2a
PVDD2b
LX2a
LX2b
IN2 G11
L4702
54 54
54 54
PVDD3a
PVDD3b
LX3a
LX3b
IN3 D3
C2, C1 B2, B1
L4703
B7, A7 B8, A8
L4704
L4722
K1 ACV_UNREG
L4705
L4706
B11, J2, K10, L10
28_PUI_DDCON_SI
29_O_DDCON_SO
30_XO_DDCON_SCK
37_XO_CS_DDCON
27_XPUI_LANC_PWR_ON
39_XO_LANC_IC_ON
76_I_BATT_IN
C3
D2
D1
G1
C1
H2
A7
VOUT
L4717
A_1.8V
L4715
D_1.8V
L4719
A_2.8V
L4716
AU_2.8V
DOUT
DIN
CLK
LD
WAKE_UP
XLANC_ON
BATT_IN
-INE8 C12
-INA D12
+INA D13
L4711
EP_2.8V
L4714
CMOS_A_3.3V
L4712
D_3.3V
L4721
MT_5.0V
IC4702
+3.3V REG
(7/15)
L4708
3
USB_3.3V
BL_H
SWITCHING
BL_L
R4706
PANEL_BL_ON
BL_ON E11
SW_OUT A11
Q4701
SWITCH
SD_1.8V
DVDD2 M13
EVER_3.0V
VRO L3
BATT_IN_SEL N4
CH6_SW C4
64_XI_POWER_OFF E10
31_O_LDO_ON D3
34_O_GPS_DD_ON E2
FLASH
UNIT
POWER SWITCH BLOCK
(PS31700)
A_2.8V
L9001
IC9001
3
R4007
5
ROLL DRIVE
(3/3)
CHARGE_
LED_VDD
D101
CHG
MODE_
LED_VDD
D102
(STILL)
D103
(MOVIE)
D_2.8V
13
RV101
(ZOOM)
D_2.8V
IC4002
+3.3V REG
(1/3)
GPS_DD_ON
XPOWER_OFF
XPOWER_OFF
LDO_ON
GPS_DD_ON
CX500V/CX500VE/CX505VE/
CX520V/CX520VE
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
3-5
POWER (2/2)
(PAGE 3-6)
35 35
35 35
GPS_DD_ON
4
1
VDD VOUT
CE
T
CX500V/CX500VE/CX505VE/
CX520V/CX520VE
IC4001
A
1
4
OUT8 B13
N7
L8
L9
L7
L6
M5
M3
51 51
R4006
SE9001
30.8kHz
D_2.8V
L2 VOUT
FR_EVER_SI
FR_EVER_SO
FR_EVER_SCK
XCS_DD
XLANC_PWR_ON
XLANC_ON
BATT_IN
FLASH CHARGE
CONTROL
(2/3)
EVER_3.0V
A_1.2V
Q4702
PVDD9 A10
VLDO3 B10
CN5001
D5002 XE_A
+
C5008
L5001
BUFFER
(1/3)
PVDD7 G1
84_VCC1
FLASH UNIT (FL31700)
W
PVDD5a
PVDD5b
LX5a
LX5b
IN5 L10
PVDD6a
PVDD6b
LX6a
LX6b
IN6 C5
51 51
HOT
SHOE
IC5001
SHOE_ON
D_1.2V_BA
D_1.2V
VLD01 A12
LD01_ON C9
08
D_2.8V
A_2.8V
M9, N9 M8, N8
ACV_UNREG
BATT/XEXT_CN
C7 77_PUI_BATT_XEXT
INIT_CHARGE_ON
F10 62_O_INIT_CHARGE
BATT_SIG
A4 14_XPUIO_BATT_SIG
19_AVR
BT001
CN4006
R4934
85_VCC2
BATT_LI_3V
+
D_2.8V
EVER_3.0V
B4, A4 B3, A3
BATT_UNREG
ACV_UNREG
R4930
17_AVCC
56 56
SHOE_UNREG
D_1.2V_BA
L4713
44_AI_BATT_SENS J5
45_AI_ACV_SENS L6
56 56
CN901
CN4004
SHOE_UNREG
ST_UNREG
M6 LANC_DC
PVDD4a
PVDD4b
LX4a
LX4b
IN4 C8
LANC INTERFACE,
HI PROCESSOR
(8/15)
CN4001
ST_UNREG
N2 VBBIN
H1 AVDD1
J1 VTR_UNREG
BATT_GND
IC4901
CN101 CN401
FP-1131
FLEXIBLE
BOARD
T5001
BATT_SIG
BATT_ON
7
BATT_LI_3V
ST-217 BOARD
M1 VBACKUP
L1 BATT_UNREG
F12, F13 G12, G13
A/V R
SHOE_UNREG
FP-1120
FLEXIBLE
BOARD
8, 10
8, 10
CN1001
FP-1123
FLEXIBLE
BOARD
CN1010
LANC_DC
SHOE_ON
IC4701
DC/DC CONVERTER, LANC DRIVE
(7/15)
F4607
HDMI
18
5V REG
(5/15)
2, 4
2, 4
(
BATT_UNREG
D4604
F4603
CN1001
+5V_POWER
50, 52
50, 52
+
BH901
BATT_ON
ACV_ON
BATT/XEXT_CN
Q4901
BUFFER
VTR_UNREG
+5V_POWER
4
8, 10
8, 10
BATT/XEXT_CN
Q4601,
Q4602
SWITCH
IO_MT_UNREG
F4605
IC3502
2, 4
2, 4
3
Q4603
ACV/BATT
SELECT
F4604
1
5
50, 52
50, 52
BATT/XEXT
CN1004
ACV_UNREG_CN
ACV_GND
K12, K13 L12, L13
2
1
SHOE_UNREG
INIT_CHARGE_ON
ACV_UNREG
ACV_GND
J901
DC IN
D_2.8V
8, 9
F4606
DC JACK
BATTERY
TERMINAL
BOARD
Q4604, Q4605
SHOE POWER SWITCH
23, 24
CN1006
8, 9
F4601
10 - 12
VC-575 BOARD (1/2)
FP-1021
FLEXIBLE
BOARD
CN4003
3
VDD3.3V
3
4
GP317 ASSY
(GP-026)
3-6. POWER BLOCK DIAGRAM (2/2)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-575 BOARD (2/2)
FP-1127
FLEXIBLE
BOARD
CN1009
D_2.8V
D_2.8V
D_1.8V
EP_2.8V
EP_2.8V
14
24
24
F12 FRC_RTG_OUT0
F28 GPIO_S__23
K31 GPIO_S__8
MS_PWR_ON
D_3.3V
IC7501
1
4
CE VOUT
VDD
3
MS_VCC_2.9V
FP-1126
FLEXIBLE
BOARD
14
22
TOUCH
PANEL I/F
D_1.8V
L6402
CN6402
VDDL
EP_2.8V
L6401
VDD
13
23
9
11
BL_H
27
BL_L
25
MMC_VCC_2.8V
2.8V REG
(1/15)
MEDIA_PWR_ON1
D_3.3V
1
4
CE VOUT
VDD
3
MMC_VCC_2.8V
D_2.8V
D_3.3V
L7511
23
BL+
45
BL–
44
IC1004
AND GATE
(1/15)
CN7301
CN7303
MS_VCC
MMC_VCC
4
4
35
35
9
IC8701
32GB MEMORY
(3/4)
D7301
(MS ACCESS)
D_2.8V
SE6601
A_2.8V
A_2.8V
L6601
PITCH/
YAW
1 VDD
IC8801
32GB MEMORY
(4/4)
R7526
D_3.3V
R7527
22
IC1005
INVERTER
(1/15)
CX520/CX520E/CX520V/CX520VE
FP-1121 FLEXIBLE BOARD
A
A_2.8V
POWER (1/2)
(PAGE 3-5)
L2801
CN1012
D_2.8V
L2803
D_2.8V
L2802
AU_2.8V
Q2801
3.6V
3.6V REG
MT_5.0V
A_1.8V
IC2801
AUDIO/VIDEO
PROCESSOR
(4/15)
R1014
R1015
3
L3501
2
IC3501
HDMI
TRANSMITTER
(5/15)
CN1002
CMOS_A_3.3V
CMOS_A_3.3V
I/O_1.8V
SIRCS_VDD
g
( REMOTE
SENSOR )
IC6503
1
VCC
SIRCS
RECEIVER
R1017
7
D_1.8V
I/O_1.8V
D_1.8V
TALLY_VDD
D6502
(TALLY)
NS_LED_A
D6503
(NIGHTSHOT)
FP-1124
FLEXIBLE
BOARD
3
CM-103 BOARD
43
CN6801
CMOS_A_3.3V
4
IN
IC6803
2.7V REG
OUT
3
A_2.7V
IC6804
CMOS IMAGER
I/O_1.8V
44
D_1.8V
42
2
4
L6801
X7501
60MHz
D_1.2V
D_1.8V
A_1.8V
D_2.8V
D_3.3V
A_2.8V
IC5202
PCI
PROCESSOR
(2/15)
CMOS_A_3.3V
IC7505
L7503
IC2301
IC7502
DDR SDRAM
(3/15)
LEVEL SHIFT
(13/15)
D_2.8V
D_1.8V
A_2.8V
SD_1.8V
D_1.8V
MT_5.0V
D_2.8V
D_1.8V
A_2.8V
D_1.2V
MT_5.0V
D_2.8V
L7502
IC8101
4 IN
OUT
3
CN1010
MR_A2.8V
29
BUFFER
(11/15)
A_1.8V
D_1.8V
LENS BLOCK
2.8V REG (9/15)
IC2201
R2218, R2219
3.0 inch
WIDE
COLOR
LCD UNIT
LCD
BACKLIGHT
MM-083 BOARD
2, 3
MS_VCC_2.9V
L7509
L7510
32
LCD901
)
33, 34
I/O_1.8V
A_2.8V
(
CN1005
(11/15 - 14/15)
FRC_RTG_IN0 G14
4
Q6401, Q6402
CN6401
D_2.8V
SE5801
PANEL
OPEN/CLOSE
IC1007
USB_3.3V
D_2.8V
BL_H
19
BL_L
20
EVER_3.0V
11
IC1001
PLL/IO/EMC/
DDR/PCI/ATA/IMG
D_3.3V
EP_2.8V
2, 3
GPIO_S__9 L31
L8002
SE6401
PANEL
( NOR/REV
)
2.9V REG
(1/15)
L8001
D_1.2V_BA
PD-389 BOARD
CN5802
D_1.8V
33, 34
SHOE_ON
XPOWER_OFF
PANEL_BL_ON
A_1.2V
CN5801
D_2.8V
23
BL_H
19
BL_L
20
EVER_3.0V
11
BL_H
BL_L
EVER_3.0V
A_1.8V
D_1.8V
14
23
FP-1128
FLEXIBLE
BOARD
CK-217 BOARD
X7504
12MHz
SDRAM,
ONENAND
(15/15)
MR_A2.8V
IC5201
ZOOM
MR
SENSOR
ZOOM AND FOCUS
DRIVE
(9/15)
IC5501
STEADYSHOT
PROCESSOR
(10/15)
CN1008
D_2.8V
08
36
FOCUS
MR
SENSOR
7
CPC
(For check)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
3-6E
MEMORY
STICK
PRO DUO
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
14
FP-1131 FLEXIBLE
BOARD
1
LEVEL3
MM-083 BOARD (SIDE A)
CONTROL
SWITCH
BLOCK
(PS31700)
FLASH UNIT
(FL31700)
1
12
LEVEL3
ST-217 BOARD
BH001
(BATTERY HOLDER)
FP-1123 FLEXIBLE
BOARD
1
61
2
CN7301
45
45
1
GP317
ASSY
(GP-026)
FP-1021
FLEXIBLE
BOARD
10
2
9
1
CN1007
CN1002
44
45
63 59
64 60
2
61
1
J901
DC IN
FP-1120 FLEXIBLE
BOARD
(
1 61
2 62
CN1001
LEVEL3
VC-575 BOARD (SIDE A)
BH901
BATTERY
TERMINAL
BOARD
)
1
1
1
26
27
g
(REMOTE
SENSOR)
1
D6502
(TALLY)
1
2
CN1006
IC7501
(Not Supplied)
LENS
BARRIER
UNIT
IC6503
CN1005
2
1
IC8101
(Not Supplied)
FP-1121
FLEXIBLE
D6503
BOARD (NIGHTSHOT)
8
CN1004
6
1
2
CN1010
SE6601
(PITCH/YAW)
DC JACK
6
51
50
2
1
CN101
11
CONTROL
SWITCH
BLOCK
(RS31700)
8
LENS BLOCK
60
62
59
12
CN1012
10
61
1
2
62
6
D7301
(ACCESS)
CN1011
1
CN401
IC8801
(Not Supplied)
CN7302
CX500V/CX500VE/CX505VE/CX520V/CX520VE
63
59
60
64
IC8701
(Not Supplied)
45
44
CN4002
6 2
5 1
59
62
60
CN4001
CN7303
(MEMORY STICK PRO DUO CONNECTOR)
FP-1126
FLEXIBLE
BOARD
14 CN4004 2
13
1
SE9001
(ROLL)
12
11
14
6 7 8 910
11 1 2 3 4 5 13
BT001
(LITHIUM STORAGE BATTERY)
2
1
CN5001
1
13
CN4006
2
14
CN901
CN1010
A/V R
1
MIC901
(MICROPHONE UNIT)
1
HOT
SHOE
CN4003
1 5
2 6
16
1
2
1
10
LEVEL3
MM-083 BOARD (SIDE B)
CN1009
44
45
CONTROL
SWITCH
BLOCK
(SK31700)
45
44
13
14
2
1
8
1
LEVEL3
CM-103 BOARD (SIDE B)
7
1
2
6
5
CN1008
CPC
(For Check)
9
CN1003
1
45
SP901
(SPEAKER)
1
45
LEVEL3
VC-575 BOARD (SIDE B)
(USB)
(HDMI)
45
CN5804
6 1
1
20
1
23
1
19
SE5801
(PANEL OPEN/CLOSE)
2 CN5802
1
22
FP-1128
FLEXIBLE
BOARD
FP-1122
FLEXIBLE
BOARD
S5802
(GPS)
ON y OFF
34
35
1
35
CX500V/CX500VE
/CX505VE/CX520V
/CX520VE
1
2
1
IC6804
(Not Supplied)
CN6801
44
45
45
21
44
45
CN5801
CK-217 BOARD
(SIDE A)
S5801
RESET
FP-1124
FLEXIBLE
BOARD
2
1
CK-217 BOARD
(SIDE B)
FP-1127
FLEXIBLE
BOARD
CN1001
21
CN5803
LEVEL3
CM-103 BOARD (SIDE A)
27
1
35
SE6401
(PANEL NOR/REV)
CN6402
PD-389 BOARD
(SIDE A)
44 CN6403
45 7 1 6 8
LCD901
TOUCH
PANEL
CN6401
3.0 INCH
WIDE COLOR
LCD UNIT
1
2
2
1
35
34
LCD
BACKLIGHT
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CK-217 BOARD
(VC-PD CONNECTION/CONTROL KEYS)
FP-1127 FLEXIBLE BOARD
(VC-CK CONNECTION)
PD-389 BOARD
(LCD/TOUCH PANEL CONNECTION)
FP-1128 FLEXIBLE BOARD
(CK-PD CONNECTION)
FP-1120 FLEXIBLE BOARD
(VC-ST CONNECTION)
FP-1131 FLEXIBLE BOARD
(HOT SHOE)
FP-1121 FLEXIBLE BOARD
(SIRCS/TALLY, NIGHTSHOT LEDS)
FLASH UNIT
(FL31700)
FP-1122 FLEXIBLE BOARD
(HDMI CONNECTOR)
FP-1123 FLEXIBLE BOARD
(A/V REMOTE CONNECTOR)
CONTROL SWITCH BLOCK
(PS31700)
FP-1124 FLEXIBLE BOARD
(VC-CM CONNECTION)
CONTROL SWITCH BLOCK
(SK31700)
FP-1126 FLEXIBLE BOARD
(VC-MM CONNECTION)
FP-1021 FLEXIBLE BOARD (ST-GP CONNECTION)
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
CONTROL SWITCH BLOCK
(RS31700)
4-2. SCHEMATIC DIAGRAMS
ENGLISH
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
Pattern box
Front of the lens
L
•
•
•
•
•
•
•
A B
A=B
Red
Blue
•
H
White
Magenta
•
Camera
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
Yellow
•
Cyan
Green
•
Kinds of capacitor
External dimensions (mm)
Case size
Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
Signal name
XEDIT → EDIT
PB/XREC → PB/REC
2: non flammable resistor
5: fusible resistor
C: panel designation
A: B+ Line
B: B– Line
J : IN/OUT direction of (+,–) B LINE.
C: adjustment for repair.
B A
Fig. a (Video output terminal output waveform)
Electronic beam scanning frame
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-2
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例
C 541
L 452
22U
10UH
TA
A
2520
↑ ↑
↑
種類 ケースサイズ
外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。
・JはBライン（＋，−）の入出力方向を示す。
・Cは調整名称。
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
パターンボックス
レンズ前面
L
カメラ
2. 図a及び図bの波形が得られるように画枠調整して下さい。
H
シ
黄 ア
ン
A B
マ
ゼ
白 ン
緑
ダ 赤
A=B
青
B A
図a（映像入出力端子出力波形）
電子ビーム走査線
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10MΩ使
用）
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
ブラウン管の画像枠
図b（テレビモニタの映像）
イメージャ交換時の注意
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
・イメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってくだ
さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-3
Schematic diagrams of the CM-103, VC-575, MM-083 and ST-217 boards are not
shown.
Pages 4-4 to 4-26 are not shown.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
1
2
4
3
5
6
CN5802
A
B
FP-1127
FLEXIBLE
10
9
8
7
11
12
35P
REG_GND
45
35
REG_GND
XBB_RST
44
34
XBB_RST
REG_GND
43
33
REG_GND
XCS_LCD
42
32
XCS_LCD
BB_SO
41
31
PANEL_SO
XBB_SCK
40
30
LCD_SCK
REG_GND
39
29
REG_GND
LCD_HS
38
28
LCD_HS
LCD_VS
37
27
LCD_VS
REG_GND
36
26
REG_GND
LCD_CLK_OUT
35
25
LCD_CLK_OUT
REG_GND
34
24
REG_GND
LCD_PDB7
33
23
LCD_D7(LCD_B_7)
LCD_PDB6
32
22
LCD_D6(LCD_B_6)
LCD_PDB5
31
21
LCD_D5(LCD_B_5)
LCD_PDB4
30
20
LCD_D4(LCD_B_4)
LCD_PDB3
29
19
LCD_D3(LCD_B_3)
LCD_PDB2
28
18
LCD_D2(LCD_B_2)
LCD_PDB1
27
17
LCD_D1(LCD_B_1)
LCD_PDB0
26
16
LCD_D0(LCD_B_0)
REG_GND
25
15
REG_GND
D_1.8V
24
14
D_1.8V
EP_2.8V
23
13
EP_2.8V
REG_GND
22
12
REG_GND
REG_GND
21
11
BL_L
BL_L
20
10
REG_GND
BL_H
19
9
BL_H
REG_GND
18
8
REG_GND
TP_Y
17
7
TP_Y
TP_SEL1
16
6
TP_SEL1
TP_X
15
5
TP_X
D_2.8V
14
4
D_2.8V
REG_GND
13
3
REG_GND
PANEL_NOR/REV
12
2
PANEL_NOR/REV
EVER_3.0V
11
1
REG_GND
PANEL_O/C
10
A
B
FP-1128
FLEXIBLE
LND001-LND035
PAGE 4-32
of LEVEL2
LND046-LND090
PAGE 4-32
of LEVEL2
C
D
REG_GND
9
GPS_SW_ON/OFF
8
FR_XRESET
7
REG_GND
6
KEY_AD2
5
EVER_3.0V
R5806
470k
REG_GND
PANEL_O/C
CX500V/CX500VE/CX505VE/
CX520V/CX520VE
GPS_SW_ON/OFF
D
FR_XRESET
D5801
MAZS056G08S0
KEY_AD2
CN5804
XPOWER_TACT_SW
XPOWER_TACT_SW 4
REG_GND
3
SP+
2
SPCN5801
1
C
XPOWER_TACT_SW
REG_GND
R5804
R5805
1200
1500
KEY_AD2
SP+
SP-
45P
REG_GND
6P
6
REG_GND
5
XPOWER_TACT_SW
4
NIGHTSHOT_SW
3
PLAY_SW
2
DISC_BURN_SW
1
REG_GND
CONTROL
SWITCH
BLOCK
(SK31700)
LND001-LND006
PAGE 4-34
of LEVEL2
E
E
CN5803
SP+
1
SP+
SP-
2
SP-
2P
SP901
(SPEAKER)
Note:SP901 is not included in CK-217 complete board.
F
1
4
PANEL_O/C
SE5801
GMR
2
EVER_3.0V
3
(PANEL OPEN/CLOSE)
C5801
0.1u
CH GND
G
2
S5801
LN5801
G
1
FR_XRESET
RESET
4
F
VD5802
XX
3
REG_GND
OFF
CX500V/
CX500VE/
CX505VE/
CX520V/
CX520VE
S5802
(GPS)
5
ON
7
6
4
1
2
3
CK-217 BOARD
GPS_SW_ON/OFF
VC-PD CONNECTION/ CONTROL KEYS
VD5801
XX MARK:NO MOUNT
R5803
0
H
H
CX500/CX500E/CX520/CX520E
CH GND
LN5802
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-27
CK-217
1
2
4
3
5
6
8
7
10
9
11
A
A
CN6401
CN6402
35P
REG_GND
1
XBB_RST
2
REG_GND
3
XCS_LCD
4
PANEL_SO
B
FP-1128
FLEXIBLE
LND036-LND070
PAGE 4-32
of LEVEL2
C
12
6
REG_GND
7
LCD_HS
8
LCD_VS
9
REG_GND
10
LCD_CLK_OUT
11
REG_GND
12
LCD_D7(LCD_B_7)
13
LCD_D6(LCD_B_6)
14
LCD_D5(LCD_B_5)
15
LCD_D4(LCD_B_4)
16
LCD_D3(LCD_B_3)
17
LCD_D2(LCD_B_2)
18
LCD_D1(LCD_B_1)
19
LCD_D0(LCD_B_0)
20
REG_GND
21
D_1.8V
22
23
REG_GND
24
BL_L
25
REG_GND
26
BL_H
27
REG_GND
1
VCOM
2
GND
3
XRESET
4
XCS
5
SI
LCD_SCK
6
SCLK
LCD_XHD
7
XHD
LCD_XHD
LCD_XVD
8
LCD_XVD
LCD_CK
9
LCD_D7
10
D7
LCD_D6
11
D6
LCD_D5
12
D5
LCD_D7
LCD_D4
13
D4
LCD_D6
LCD_D3
14
D3
LCD_D4
LCD_D2
15
D2
LCD_D5
LCD_D1
16
D1
LCD_D3
LCD_D0
17
D0
18
VSS
19
VS
20
COMC
21
VCOMH
22
VDDL
23
VDD
24
COMDC
25
NC
26
C4N
27
C1N
28
C4P
29
C1P
30
VDD2
31
VR2_O
32
DCCLKB
33
DCCLK
34
VSS_0
35
GVDD
36
VR2_I
37
GVSS
38
DCK1
39
DCK1B
40
VSS
41
DCK2
42
DCK2B
43
VCOM
44
BL-
45
BL+
XBB_RST
R6412 XX
XBB_RST
CL6401
XCS_LCD
XCS_LCD
CL6402
5
LCD_SCK
EP_2.8V
C6406
XX
BB_SO
BB_SO
CL6403
LCD_SCK
R6401
XX
R6402
XX
R6403
7
5
3
1
XX
LCD_CK
RB6401
XX
8
6
4
2
7
5
3
1
RB6402
XX
8
6
4
2
LCD_D1
LCD_D2
LCD_D0
C6416
2.2u
C6407
2.2u
C6408
2.2u
10uH
L6402
L6401
10uH
C6401
4.7u
R6413
C6402
1u
56k
BL_L
BL_H
28
TP_Y
29
TP_Y
TP_SEL1
30
TP_SEL1
TP_X
31
TP_X
D_2.8V
32
REG_GND
33
PANEL_NOR/REV
34
C6409
2.2u
C6417
2.2u
C6410
2.2u
C6418
2.2u
D_2.8V
VD6401
XX
C6419
REG_GND
35
D
4
2.2u
3
VD6402
XX
SE6401
1
45P
C6403
0.1u
2
(PANEL NOR/REV)
C6411
1u
C6412
1u
C6413
1u
C6414
1u
C6415
1u
CL6404
BL_L
CL6405
BL_H
XVD
DCK
B
LCD901
3.0 INCH
WIDE
COLOR
LCD UNIT
C
D
LCD
BACKLIGHT
E
E
D_2.8V
TP_SEL1
1
4
6
3
2
5
TP_Y
Q6401
XP411F-TXE
TOUCH PANEL I/F
CN6403
TP_X
TP_XL
2
TP_XR
3
N.C.
4
TP_YU
5
F
6
2
7
5
TOUCH
PANEL
TP_YL
6
3
6P
1
F
N.C.
8
D6401
XX
4
Q6402
XP421F-TXE
TOUCH PANEL I/F
1
4
C6404
0.01u
C6405
0.0047u
50V
3
2
5
1
Note: LCD901 is not included in PD-389 complete board.
G
G
PD-389 BOARD
LCD/TOUCH PANEL CONNECTION
XX MARK:NO MOUNT
H
H
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-28
PD-389
1
2
3
4
5
6
7
8
A
A
CN101
ST_GND
1
60P
ST_GND
ST_UNREG
2
CN401
ST_UNREG
ST_GND
3
ST_GND
ST_UNREG
60P
1
ST_GND
ST_UNREG
2
3
ST_GND
ST_UNREG
4
5
6
5
SHOE_GND
7
SHOE_GND
SHOE_UNREG
8
B
SHOE_UNREG
10
XPHOTO_LED
11
XPHOTO_LED
XCHARGE_LED
12
XCHARGE_LED
XSTART/STOP
13
XSTART/STOP
XCAM_LED
14
XCAM_LED
KEY_AD1
15
KEY_AD1
LANC_SIG
16
LANC_SIG
XSTRB_FULL
17
XSTRB_FULL
MIC_GND
18
MIC_GND
STRB_CHARGE
19
STRB_CHARGE
STROBE_ON
21
STROBE_ON
EXT_STOROBE_ON
23
EXT_STOROBE_ON
HOTSHOE_ID1
HOTSHOE_ID2
C
CX500V/
CX500VE/
CX505VE/
CX520V/
CX520VE
SHOE_GND
25
HOTSHOE_ID1
27
HOTSHOE_ID2
29
REG_GND
REG_GND
INT_MIC_R
28
MIC_GND
30
32
34
39
GPS_FIRMUP
41
GPS_BUF_CNTL
43
REG_GND
45
REG_GND
47
XSYS_RST
SHOE_MIC_FR
36
MIC_GND
38
UART3_SI_BUFF
40
UART3_SO_BUFF
42
REG_GND
44
VST_C_RESET_R
46
REG_GND
48
49
REG_GND
D_2.8V
50
51
A_2.8V
D_2.8V
52
8
9
SHOE_GND
SHOE_UNREG
10
SHOE_UNREG
XPHOTO_LED
11
XPHOTO_LED
XCHARGE_LED
12
XCHARGE_LED
XSTART/STOP
13
XSTART/STOP
XCAM_LED
14
XCAM_LED
LANC_SIG
KEY_AD1
15
KEY_AD1
LANC_SIG
16
XSTRB_FULL
17
XSTRB_FULL
MIC_GND
18
MIC_GND
STRB_CHARGE
19
STRB_CHARGE
SHOE_MIC_FL
20
SHOE_MIC_FL
STROBE_ON
21
STROBE_ON
EXT_STOROBE_ON
23
EXT_STOROBE_ON
HOTSHOE_ID1
25
HOTSHOE_ID2
MIC_GND
22
INT_MIC_L
24
HOTSHOE_ID1
MIC_GND
26
27
HOTSHOE_ID2
INT_MIC_R
28
29
REG_GND
MIC_GND
30
31
REG_GND
INT_MIC_F
32
33
REG_GND
MIC_GND
34
SHOE_MIC_FR
36
MIC_GND
38
UART3_SI_BUFF
40
UART3_SI_BUFF
UART3_SO_BUFF
INT_MIC_L
SHOE_MIC_FR
UART3_SI_BUFF
UART3_SO_BUFF
CX500V/
CX500VE/
CX505VE/
CX520V/
CX520VE
GPS_DD_ON
35
GPS_DD_ON
XGPS_RST
37
XGPS_RST
GPS_FIRMUP
39
GPS_FIRMUP
GPS_BUF_CNTL
41
GPS_BUF_CNTL
UART3_SO_BUFF
42
43
REG_GND
REG_GND
44
45
REG_GND
VST_C_RESET_R
46
47
XSYS_RST
REG_GND
48
INT_MIC_F
SHOE_MIC_FR
C
VST_C_RESET_R
XSYS_RST
VST_C_RESET_R
CX500V/
CX500VE/
CX505VE/
CX520V/
CX520VE
D_2.8V
EVER_3.0V
54
EVER_3.0V
BATT_LI_3V
56
BATT_LI_3V
57
ROLL_AD
REG_GND
58
60
INT_MIC_R
INT_MIC_F
REG_GND
D_2.8V
49
REG_GND
D_2.8V
50
A_2.8V
51
A_2.8V
D_2.8V
52
ZOOM_VR_AD
53
ZOOM_VR_AD
EVER_3.0V
54
EVER_3.0V
55
REG_GND
BATT_LI_3V
56
BATT_LI_3V
ROLL_AD
57
ROLL_AD
REG_GND
58
REG_GND
59
REG_GND
REG_GND
60
REG_GND
REG_GND
62 61
D
B
INT_MIC_R
ZOOM_VR_AD
REG_GND
SHOE_UNREG
INT_MIC_L
55
REG_GND
SHOE_GND
SHOE_MIC_FL
53
59
7
26
MIC_GND
XGPS_RST
ROLL_AD
MIC_GND
INT_MIC_F
GPS_DD_ON
ZOOM_VR_AD
24
REG_GND
37
A_2.8V
INT_MIC_L
REG_GND
35
XSYS_RST
22
33
XGPS_RST
GPS_BUF_CNTL
20
MIC_GND
31
GPS_DD_ON
GPS_FIRMUP
SHOE_MIC_FL
6
SHOE_UNREG
SHOE_GND
9
ST_UNREG
4
64 63 62 61
VC-557
(1/15)
D
ST-217
(1/3)
CN1001
PAGE 4-5
of LEVEL3
CN4001
PAGE 4-26
of LEVEL3
E
E
FP-1120 FLEXIBLE BOARD
VC-ST CONNECTION
XX MARK:NO MOUNT
F
F
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-29
FP-1120
1
3
2
1
4
A
A
3
2
4
A
A
Pin
Pin
D6503
SML-J13RTT86
(NIGHTSHOT)
C6501
10u
C6502
1u
2
B
NS_LED_K
LND008
NS_LED_A
LND007
SIRCS_SIG
LND006
REG_GND
LND005
REG_GND
LND004
SIRCS_VDD
LND003
TALLY_VDD
LND002
1
LND001
F_TALLY_LED
3
8
VC-575
(1/15)
1
LND001
REG_GND
2
LND002
REG_GND
3
LND003
TMDS DATA2 +
CN1012
LND004
PAGE 4-5
of LEVEL3
B
1
LND006
TMDS DATA1 +
LND007
TMDS DATA1 -
LND008
REG_GND
LND009
TMDS DATA0 +
CN1006
LND010
TMDS DATA0 -
PAGE 4-5
of LEVEL3
LND011
REG_GND
LND012
(REMOTE SENSOR)
C
FP-1121 FLEXIBLE BOARD
C
SIRCS/TALLY, NIGHTSHOT LEDS
2
3
TMDS CLOCK +
4
3
1
2
4
3
1
2
4
3
LF003 1
2
4
3
LF0041
2
TMDS_DATA2_SHIELD
2
TMDS_DATA2_+
3
TMDS_DATA2_-
4
TMDS_DATA1_SHIELD
5
TMDS_DATA1_+
6
TMDS_DATA1_-
7
TMDS_DATA0_SHIELD
8
TMDS_DATA0_+
9
TMDS_DATA0_-
10
TMDS_CLOCK_SHIELD
11
TMDS_CLOCK_+
12
TMDS_CLOCK_-
13
DDC_CEC_GND
TMDS CLOCK -
14
CEC
LND014
REG_GND
15
SCL
LND015
CEC
16
SDA
LND016
REG_GND
17
RESERVED
LND017
SCL
18
+5V_POWER
LND018
SDA
19
HPD
LND019
+5V POWER
LND020
+5V POWER
HPD
26
LND022
REG_GND
27
LND023
REG_GND
B
HDMI
C
VDR001
XX
4
LND028
A
19P
1
LND013
LND021
25
08
1
REG_GND
LF001
LF002
VC-575
(1/15)
D6502
SML-D12V8WT86SN
(TALLY)
g
C
LND005
B
4
IC6503
RS-770
SIRCS RECEIVER
TMDS DATA2 -
CN1001
CHASSIS GND
D
D
E
E
A
Pin
10
B
LND010
S_Y_I/O
10
LND011
S_C_I/O
9
VIDEO_I/O
LND012
VIDEO_I/O
8
REG_GND
S_Y_I/O
LND013
VC-575
(1/15)
LANC_DC
7
JACK_AD
LND014
REG_GND
6
AUDIO_R
CN1007
LND015
REG_GND
5
S_C_I/O
PAGE 4-5
of LEVEL3
1
LND016
MULTI_JACK_IN
4
LANC_DC
LND017
LANC_SIG
3
REG_GND
LND018
AUDIO_R_I/O
2
LANC_SIG
1
AUDIO_L
LND019
FB001
FB002
AUDIO_L_I/O
CN1010
LND020
14 13
A/V R
B
12 11
10P
FP-1122 FELXIBLE BOARD
CHASSIS_GND
HDMI CONNECTOR
XX MARK:NO MOUNT
C
FP-1123 FLEXIBLE BOARD
F
C
F
A/V REMOTE CONNECTOR
08
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-30
FP-1121, FP-1122, FP-1123
1
2
3
4
A
2
1
3
4
A
A
A
Pin
Pin
Pin
1
2
3
B
C
VC-575
(1/15)
CN1002
PAGE 4-5
of LEVEL3
D
Pin
1
LND001
REG_GND
REG_GND
LND046
1
LND002
MS_VCC_2.9V
MS_VCC_2.9V
LND047
2
LND003
MS_VCC_2.9V
MS_VCC_2.9V
LND048
3
LND004
D_2.8V
D_2.8V
LND049
REG_GND
LND050
XMS_ACC_LED
LND051
LND001
REG_GND
REG_GND
LND145
45
2
LND002
I/O_1.8V_CN1301
I/O_1.8V_CN1301
LND144
44
3
LND003
CMOS_A_3.3V_CN1301
CMOS_A_3.3V_CN1301
LND143
43
LND004
D_1.8V/CMOS_D_2.8V
D_1.8V/CMOS_D_2.8V
LND142
LND005
REG_GND
REG_GND
LND141
LND006
REG_GND
REG_GND
LND140
LND007
REG_GND
REG_GND
LND139
LND008
REG_GND
REG_GND
LND138
LND009
SENS_DATA_M_7
SENS_DATA_M_7
LND137
LND010
SENS_DATA_P_7
SENS_DATA_P_7
LND136
LND011
REG_GND
REG_GND
LND135
LND012
SENS_DATA_M_6
SENS_DATA_M_6
LND134
LND013
SENS_DATA_P_6
SENS_DATA_P_6
LND133
LND014
REG_GND
REG_GND
LND132
LND015
SENS_DATA_M_5
SENS_DATA_M_5
LND131
LND016
SENS_DATA_P_5
SENS_DATA_P_5
LND017
REG_GND
REG_GND
LND129
LND018
SENS_DATA_M_4
SENS_DATA_M_4
LND128
B
B
SENS_DATA_P_4
SENS_DATA_P_4
LND127
LND020
REG_GND
REG_GND
LND126
LND021
SENS_CLK_M
SENS_CLK_M
LND125
CN6801
LND022
SENS_CLK_P
SENS_CLK_P
LND124
PAGE 4-4
of LEVEL3
LND023
REG_GND
REG_GND
LND123
LND024
SENS_DATA_M_3
SENS_DATA_M_3
LND122
LND025
SENS_DATA_P_3
SENS_DATA_P_3
LND121
LND026
REG_GND
REG_GND
LND120
LND027
SENS_DATA_M_2
SENS_DATA_M_2
LND119
LND028
SENS_DATA_P_2
SENS_DATA_P_2
LND118
LND029
REG_GND
REG_GND
LND117
LND030
SENS_DATA_M_1
SENS_DATA_M_1
LND116
LND031
SENS_DATA_P_1
SENS_DATA_P_1
LND115
LND032
REG_GND
REG_GND
LND114
LND033
SENS_DATA_M_0
SENS_DATA_M_0
LND113
LND034
SENS_DATA_P_0
SENS_DATA_P_0
LND112
LND035
REG_GND
REG_GND
LND111
LND036
REG_GND
REG_GND
LND110
LND037
SENS_VD
SENS_VD
LND109
LND038
SENSSO
SENSSO
LND108
LND039
SENS_HD
SENS_HD
LND040
SENSSCK
SENSSCK
LND106
LND041
SENSXCS
SENSXCS
LND105
C
C
LND007
REG_GND
REG_GND
LND052
LND008
MSX_CLK
MSX_CLK
LND053
LND009
REG_GND
REG_GND
LND054
LND010
REG_GND
REG_GND
LND055
LND011
MSX_BIO3
MSX_BIO3
LND056
XMS_IN
XMS_IN
LND057
MSX_BIO2
MSX_BIO2
LND058
LND014
MSX_BIO0
MSX_BIO0
LND059
LND015
MSX_BIO1
MSX_BIO1
LND060
LND016
MSX_BS
MSX_BS
LND061
LND017
REG_GND
REG_GND
LND062
LND018
REG_GND
REG_GND
LND063
LND019
MMC_BIO0
MMC_BIO0
LND064
LND020
MMC_BIO1
MMC_BIO1
LND065
LND021
MMC_BIO2
MMC_BIO2
LND066
CN1005
LND022
MMC_BIO3
MMC_BIO3
LND067
PAGE 4-5
of LEVEL3
LND023
MMC_BIO4
MMC_BIO4
LND068
LND024
MMC_BIO5
MMC_BIO5
LND069
LND025
MMC_BIO6
MMC_BIO6
LND070
LND026
MMC_BIO7
MMC_BIO7
LND071
LND027
REG_GND
REG_GND
LND072
LND028
MMC_CMD
MMC_CMD
LND073
LND029
REG_GND
REG_GND
LND074
LND030
MMC_CLK
MMC_CLK
LND075
LND031
REG_GND
REG_GND
LND076
LND032
REG_GND
REG_GND
LND077
LND033
MMC_VCC_2.9V
MMC_VCC_2.9V
LND078
LND034
MMC_VCC_2.9V
MMC_VCC_2.9V
LND079
LND035
A_2.8V
A_2.8V
LND080
LND036
VST_C_RESET_P
VST_C_RESET_P LND081
LND037
VST_C_RESET_Y
VST_C_RESET_Y LND082
LND038
PITCH_AD
LND039
YAW_AD
LND040
VREF_GYRO
LND041
D
D
XMS_ACC_LED
LND013
VC-575
(1/15)
CM-103
REG_GND
LND006
LND012
LND130
LND019
LND005
CN7301
PAGE 4-21
of LEVEL3
LND083
LND084
VREF_GYRO
LND085
REG_GND
REG_GND
LND086
LND042
XPON_SW
XPON_SW
LND087
43
LND043
DIAL_A
DIAL_A
LND088
43
DIAL_B
LND089
44
REG_GND
LND090
45
LND042
REG_GND
REG_GND
LND104
LND043
XFLASH_RST
XFLASH_RST
LND103
3
44
LND044
DIAL_B
44
LND044
CLK_CMOS_IN
CLK_CMOS_IN
LND102
2
45
LND045
REG_GND
LND045
REG_GND
REG_GND
LND101
1
E
E
E
FP-1124 FLEXIBLE BOARD
FP-1126 FLEXIBLE BOARD
VC-CM CONNECTION
VC-MM CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
C
D
YAW_AD
LND107
E
MM-083
(2/4)
PITCH_AD
43
45
B
(PRINTED WIRING BOARD is omitted.)
F
F
08
F
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-31
FP-1124, FP-1126
1
2
3
Pin
A
LND001
SP-
SP-
LND046
2
LND002
SP+
SP+
LND047
3
LND003
REG_GND
REG_GND
LND048
LND004
XPOWER_TACT_SW
XPOWER_TACT_SW
LND049
LND005
KEY_AD2
KEY_AD2
LND050
LND006
REG_GND
REG_GND
LND051
LND007
FR_XRESET
LND008
GPS_SW_ON/OFF
LND009
REG_GND
LND010
PANEL_O/C
LND011
LND012
EVER_3.0V
PANEL_NOR/REV
LND013
REG_GND
LND014
D_2.8V
LND015
TP_X
LND016
TP_SEL1
LND017
TP_Y
LND018
VC-575
(1/15)
REG_GND
REG_GND
LND054
PANEL_O/C
LND055
EVER_3.0V
REG_GND
D_2.8V
LND060
TP_SEL1
LND061
TP_Y
REG_GND
D_1.8V
REG_GND
LND026
LCD_PDB0
REG_GND
REG_GND
LND067
EP_2.8V
LND068
D_1.8V
REG_GND
LCD_PDB0
LCD_PDB1
LND072
LCD_PDB2
LND073
LND029
LCD_PDB3
LCD_PDB3
LND074
LND030
LCD_PDB4
LCD_PDB4
LND075
LCD_PDB6
LCD_PDB6
LND077
LND033
LCD_PDB7
LCD_PDB7
LND078
LND035
LCD_CLK_OUT
LND036
REG_GND
REG_GND
LCD_CLK_OUT
REG_GND
LCD_VS
LCD_VS
LND082
LCD_HS
LND083
XBB_SCK
LND041
BB_SO
LND005
TP_X
LND006
TP_SEL1
LND007
TP_Y
LND008
REG_GND
LND009
BL_H
LND010
REG_GND
REG_GND
D
LND084
XBB_SCK
LND085
BB_SO
LND086
LND087
LND042
XCS_LCD
XCS_LCD
43
LND043
REG_GND
REG_GND
LND088
44
LND044
XBB_RST
XBB_RST
LND089
45
LND045
REG_GND
REG_GND
LND090
E
LND036
35
LND037
34
REG_GND
LND038
33
D_2.8V
LND039
TP_X
LND040
TP_SEL1
LND041
TP_Y
LND042
REG_GND
LND043
BL_H
LND044
REG_GND
LND045
BL_L
LND046
LND047
EP_2.8V
EP_2.8V
LND048
LND014
D_1.8V
D_1.8V
LND049
CK-217
LND015
REG_GND
REG_GND
LND050
CN5802
LND016
LCD_D0
LCD_D0
LND051
LND017
LCD_D1
LCD_D1
LND052
LND018
LCD_D2
LCD_D2
LND053
LND019
LCD_D3
LCD_D3
LND054
LND020
LCD_D4
LCD_D4
LND055
LND021
LCD_D5
LCD_D5
LND056
LND022
LCD_D6
LCD_D6
LND057
LND023
LCD_D7
LCD_D7
LND058
LND024
REG_GND
LND025
LCD_CLK_OUT
LND026
REG_GND
LND027
C
D
REG_GND
PANEL_NOR/REV
REG_GND
LND011
BL_L
LND012
REG_GND
LND013
B
PD-389
CN6401
PAGE 4-28
of LEVEL2
C
REG_GND
LND059
LCD_CLK_OUT
LND060
REG_GND
LND061
LCD_VS
LCD_VS
LND062
LND028
LCD_HS
LCD_HS
LND063
LND029
REG_GND
REG_GND
LND064
LND030
LCD_SCK
LCD_SCK
LND065
LND031
PANEL_SO
PANEL_SO
LND066
LND032
XCS_LCD
XCS_LCD
LND067
33
LND033
REG_GND
REG_GND
LND068
3
34
LND034
XBB_RST
XBB_RST
LND069
2
35
LND035
REG_GND
REG_GND
LND070
1
LND081
LCD_HS
LND040
D_2.8V
LND080
LND038
REG_GND
LND004
LND079
LND037
LND039
REG_GND
LND076
LND032
REG_GND
LND003
PAGE 4-27
of LEVEL2
C
LND071
LCD_PDB2
LCD_PDB5
CN5801
PAGE 4-27
of LEVEL2
LND070
LCD_PDB1
LND034
3
LND069
LND028
LCD_PDB5
CK-217
LND066
LND027
LND031
PANEL_NOR/REV
LND063
LND065
EP_2.8V
REG_GND
LND002
LND062
LND064
LND023
LND001
2
LND059
TP_X
Pin
1
B
B
LND058
BL_L
REG_GND
Pin
PANEL_NOR/REV LND057
BL_H
LND022
A
3
LND056
BL_L
REG_GND
A
A
2
LND052
BL_H
LND025
D
4
3
1
GPS_SW_ON/OFF LND053
LND020
LND024
C
FR_XRESET
LND019
LND021
CN1009
PAGE 4-5
of LEVEL3
2
Pin
1
B
1
4
43
44
45
E
E
E
FP-1127 FLEXIBLE BOARD
FP-1128 FLEXIBLE BOARD
VC-CK CONNECTION
CK-PD CONNECTION
(PRINTED WIRING BOARD is omitted.)
F
D
(PRINTED WIRING BOARD is omitted.)
F
F
F
08
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-32
FP-1127, FP-1128
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
3
2
4
2
1
3
4
LND040
RV101
22k
CASSIS GND
T
Pin
A
A
16
LND016
GND
15
LND015
USB-
14
LND014
USB+
GND
LND034
14
LND013
SHOE_CONT
SHOE_CONT
LND033
13
LND012
LANC
LANC
LND032
12
LND011
STROBE
STROBE
LND031
LND010
ID2
ID2
LND030
LND009
UNREG
Unreg
LND029
LND008
UNREG
Unreg
LND028
LND007
ID1
ID1
LND027
LND006
MIC_RL
MicRL
LND026
LND005
MIC_RR
MicRR
LND025
LND004
MIC_GND
MicGND
LND024
3
LND003
MIC_FL
MicFL
LND023
3
2
LND002
MIC_FR
MicFR
LND022
2
CN901
HOT
SHOE
B
1
LND001
A
A
Pin
GND
GND
LND021
W
(ZOOM)
ST-217
(1/3)
Pin
CN4004
PAGE 4-24
of LEVEL3
B
14
LND014
REG_GND
13
LND013
D_2.8V
12
LND012
ZOOM_VR
LND011
KEY_AD1(PHOTO_FREEZE)
LND010
KEY_AD1(PHOTO_REC)
LND009
REG_GND
B
ST-217
(1/3)
CN4006
PAGE 4-24
of LEVEL3
1
Note:CN901 is not included in FP-1131 flexible board.
LND008
XMODE_SW
LND007
XCAM_LED
2 S104 1
SML-412MWT86
D103
LND006
XPHOTO_LED
LND005
MODE_LED_VDD
LND004
XCHARGE_LED
3
LND003
CHARGE_LED_VDD
2
LND002
XSTART/STOP
1
LND001
REG_GND
SML-412MWT86
D102
(STILL)
SML-512WWT86
D101
CHG
C
FP-1131 FLEXIBLE BOARD
C
4
2 S102 1
MODE SW
4
3
2 S101 1
START/STOP
2
3
4
A
1
A
3
C
CONTROL SWITCH BLOCK (PS31700) is replaced as a block,
so that PRINTED WIRING BOARD is omitted.
08
1
3
CONTROL SWITCH BLOCK
(PS31700)
HOT SHOE
08
PHOTO
(SHUTTER)
(MOVIE)
4
C
B
(FOCUS)
4
3
2 S103 1
3
2
4
A
A
Pin
XE_A
LND051
XE-A
LND012
12
XE-A
LND011
11
XE-A
LND010
10
S001
DIAL_A
N.C.
MANUAL
DIAL
N.C.
FLASH
UNIT
TRIGEER
LND053
B
COMMON
LND052
TRIGER
LND007
TRIGER
LND006
ST-217
(2/3)
Pin
S002
DIAL_B
CN5001
PAGE 4-25
of LEVEL3
N.C.
N.C.
XE-K
LND003
3
XE_K
XE-K
LND002
2
LND050
XE-K
LND001
1
B
B
4
3
(MANUAL BUTTON)
FLASH UNIT(FL31700)
C
FLASH UNIT(FL31700)is replaced as a block,
so that PRINTED WIRING BOARD is omitted.
2 S003 1
C
C
DIAL_A
LND006
DIAL_B
LND005
XPON_SW
LND004
REG_GND
LND003
REG_GND
LND002
REG_GND
LND001
REG_GND
6
MM-083
(2/4)
B
CN7302
PAGE 4-21
of LEVEL3
1
CONTROL SWITCH BLOCK
(RS31700)
C
CONTROL SWITCH BLOCK (RS31700) is replaced as a block,
so that PRINTED WIRING BOARD is omitted.
08
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-33
FP-1131, FL31700, PS31700, RS31700
2
1
3
A
POWER
Pin
6
B
4
CK-217
CN5804
PAGE 4-27
of LEVEL2
1
A
(VIEW IMAGES)
2 S001 1
2 S003 1
4
4
3
3
NIGHTSHOT
(DISC BURN)
2 S002 1
2 S004 1
4
4
REG_GND
LND006
REG_GND
LND005
XPOWER_TACT_SW
LND004
NIGHTSHOT_SW
LND003
PLAY_SW
LND002
DISC_BURN_SW
LND001
REG_GND
3
3
B
CONTROL SWITCH BLOCK
(SK31700)
C
C
CONTROL SWITCH BLOCK (SK31700) is replaced as a block,
so that PRINTED WIRING BOARD is omitted.
08
2
1
3
4
A
A
Pin
ST-217
(1/3)
LND003
F/U
F/U
LND017
1
5
LND004
SI
SI
LND018
2
LND005
GND
GND
LND019
POWER
LND020
SO
LND021
5
X_RST
LND022
6
CN4003
B
Pin
6
PAGE 4-24
of LEVEL3
LND006
POWER
2
LND007
SO
1
LND008
X_RST
GP317
ASSY
(GP-026)
B
Note: GP317 assy (GP-026) is not
included in FP-1021 flexible board.
FP-1021 FLEXIBLE BOARD
C
: CX500V/CX500VE/CX505VE/CX520V/CX520VE
ST-GP CONNECTION
C
(PRINTED WIRING BOARD is omitted.)
08
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-34
SK31700, FP-1021
4-3. PRINTED WIRING BOARDS
Link
CK-217 BOARD
FP-1122 FLEXIBLE BOARD
FP-1120 FLEXIBLE BOARD
FP-1123 FLEXIBLE BOARD
FP-1121 FLEXIBLE BOARD
FP-1131 FLEXIBLE BOARD
PD-389 BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
• Chip parts.
Transistor
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
B
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
3
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-35
1 23
1 2 3 3 2 1 1 2 3 3 2 1
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
1
2
3
2
4
1
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
3
1 6 54
Printed wiring boards of the CM-103, VC-575, MM-083 and ST-217 boards are not
shown.
Pages 4-36 to 4-40 are not shown.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
CK-217 (4 layers), FP-1120 (2 layers), FP-1121 (1 layer)
: Uses unleaded solder.
CK-217 BOARD (SIDE A)
FP-1120 FLEXIBLE BOARD
LN5802
63
4
3
59
61
1
CN401
64
VD5801
R5806
RESET
1
C5801
S5801
R5803
2
2
5
2
62
LN5801
3
7
60
SE5801
(PANEL OPEN/CLOSE)
2 1
VD5802
4
34
S5802
(GPS)
ON y OFF
CN5802
6
4
3
2
1
1
35
1-878-918-
08
60
2
62
61
CN101
59
11
1
1-878-92008
CK-217 BOARD (SIDE B)
2
11
44
CN5803
CN5801
2
CN5804
1
1
6
45
1
R5804
R5805
1-878-918-
FP-1121 FLEXIBLE BOARD
3
08
11
2
D5801
g
8
IC6503
(REMOTE SENSOR)
4
D6503
(NIGHTSHOT)
C6501
1
1
LND008
LND007
LND006
LND005
LND004
LND003
LND002
LND001
C6502
08
D6502
(TALLY)
1-878-92111
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-41
CK-217, FP-1120, FP-1121
PD-389 (2 layers)
: Uses unleaded solder.
PD-389 BOARD
C6403
3
8
CN6403
1
1
3
4
D6401
3
1
Q6402
C6404
Q6401
4
6
6
C6405
4
1
6
5
3 4
VD6402
SE6401
(PANEL NOR/REV)
2 1
7
CL6405
C6401
C6414
C6415
C6412
C6413
C6411
7
2
8
RB6401
8
35
1
C6417
C6409
C6408
C6416
R6413
1
RB6402
CN6402
7
R6403
R6402
R6401
C6419
C6410
C6402
L6402
L6401
C6418
44
45
CL6404
C6407
2
1
CN6401
2
CL6403
CL6401
1
34
2
VD6401
CL6402
R6412
C6406
1-878-919-
08
11
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-42
PD-389
FP-1122 (2 layers), FP-1123 (2 layers)
: Uses unleaded solder.
FP-1123 FLEXIBLE BOARD
13
9 5 10
14
LND020
CN1010
11
12
1 6 2
7 3 8 4
A/V R
FB001
FB002
08
CN1001
FP-1122 FLEXIBLE BOARD
(HDMI)
21
23
LND028
1
19
2
3
LF004
VDR001
1
4
2
3
LF003
1
4
2
3
LF002
1
4
1
4
LF001
2
22
3
20
1
LND001
LND002
LND003
LND004
LND005
LND006
LND007
LND008
LND009
08
1-878-922-
10
1
LND013
LND014
LND015
LND016
LND017
LND018
LND019
LND020
LND021
LND022
LND023
LND019
LND018
LND017
LND016
LND015
LND014
LND013
LND012
LND011
LND010
LND010
LND011
LND012
1-878-923- 11
11
27
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-43
FP-1122, FP-1123
FP-1131 (1 layer)
: Uses unleaded solder.
FP-1131 FLEXIBLE BOARD
LND040
14
LND034
LND032
LND031
LND030
LND029 LND028
LND027
LND026
LND025
LND024
LND023
LND022
LND021
1
LND012
LND011
LND010
LND008 LND009
LND007
LND006
LND005
LND004
LND003
LND002
LND001
16
LND016
1-878-931- 11
1
08
HOT
SHOE
Note: CN901 is not included in FP-1131 flexible board.
CN901
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
4-44E
FP-1131
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
OVERALL SECTION
B
FRONT PANEL SECTION
E
LENS SECTION-1
D
CABINET (TOP/R) SECTION
CABINET (TOP) SECTION
G
H
F
VC-575 SECTION
LENS SECTION-2
BT PANEL SECTION
J
I
CABINET (R) SECTION
C
HINGE SECTION
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
Link
ELECTRICAL PARTS LIST
ACCESSORIES
J
FP-1122 FLEXIBLE BOARD F
FP-1127 FLEXIBLE BOARD J
FP-1021 FLEXIBLE BOARD B
FP-1123 FLEXIBLE BOARD E
FP-1128 FLEXIBLE BOARD J
FP-1120 FLEXIBLE BOARD E
FP-1124 FLEXIBLE BOARD G
FP-1131 FLEXIBLE BOARD D
FP-1121 FLEXIBLE BOARD B
FP-1126 FLEXIBLE BOARD E
PD-389 BOARD
CK-217 BOARD
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
I
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
• Abbreviation
AUS : Australian model
CH : Chinese model
CND : Canadian model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-1
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，必ず指定の部品を使用してください。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
DISASSEMBLY
HARDWARE LIST
5-1-1. OVERALL SECTION
ns: not supplied
#2
#2
ns
ns
#2
#11
6
5
#2
4
7
Front Panel Section
(See Page 5-3)
#2
#11
3
2
#1
1 (Note)
Note:
Note:
キャビネット (底) 組立の交換時は1-15ページの “キャビ
ネット (底) 組立交換時の注意” を参照してください。
Refer to page 1-15 “Precaution on replacing the Cabinet
(Bottom) Assy” when changing the Cabinet (Bottom) Assy.
Ref. No.
Part No.
1
2
* 3
4
(Note)
4-154-929-01
4-154-976-01
X-2514-500-1
4
#1
Description
CABINET (BOTTOM)
SCREW, TRIPOD
WINDOW, REMOTE CONTROL
CABINET (L) ASSY (G)
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
X-2514-501-1 CABINET (L) ASSY (N)
(CX500/CX500E/CX520/CX520E)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Ref. No.
Part No.
5
6
* 7
2-589-376-01 FOOT (395), RUBBER
2-664-928-41 BELT, GRIP
4-154-969-01 SHEET, CM SHIELD
5-2
#1
#2
#11
Description
2-635-562-11 SCREW (M1.7) (Black)
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
5-1-2. FRONT PANEL SECTION
DISASSEMBLY
HARDWARE LIST
57
#11
58
#11
61
56
59
55
#2
#1
#11
54
60
Cabinet (Top/R) Section
(See Page 5-4)
53
#2
51
#3
#12
52
(Note)
HDR-CX500V/CX500VE/CX505VE/
CX520V/CX520VE
Note: GP317 Assy (GP-026) 交換時は，1-14ペー
ジ「1-5. GPS 受信確認」を必ずお読み
ください。
Note: Be sure to read “1-5. GPS RECEIVING
CHECK” on page 1-7 when you exchange
the GP317 Assy (GP-026).
62
• Refer to page 5-1 for mark 0.
Ref. No.
51
52
53
54
55
55
56
0 57
Part No.
Description
1-877-407-11 FP-1021 FLEXIBLE BOARD
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
A-1735-959-A GP317 ASSY (GP-026)
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
(Note)
4-154-894-01 RING, LENS
4-154-893-01 RING, F
X-2514-498-1 PANEL ASSY (317), F (CX500V: J)
Ref. No.
Part No.
58
* 59
A-1735-705-A FP-1121 FLEXIBLE BOARD, COMPLETE
4-154-896-01 PLATE, F GROUND
60
* 61
62
4-154-895-01 PLATE, F RING ELECTROSTATIC
4-159-687-01 SHEET, ST SHIELD
2-590-635-01 TAPE (AS1/2)
X-2514-499-1 PANEL ASSY (318), F (EXCEPT CX500V: J)
A-1729-238-A LENS BARRIER UNIT
1-487-269-11 FLASH UNIT (FL31700)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-3
#1
#2
#3
#11
#12
2-635-562-11
2-635-562-31
2-660-401-01
3-078-890-11
3-080-204-21
Description
SCREW (M1.7) (Black)
SCREW (M1.7) (Black)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW, TAPPING (Silver)
SCREW, TAPPING, P2 (Black)
5. REPAIR PARTS LIST
5-1-3. CABINET (TOP/R) SECTION
#2
DISASSEMBLY
HARDWARE LIST
101
Cabinet (Top) Section
(See Page 5-5)
#11
#2
#1
BT Panel Section
(See Page 5-9)
#1
#2
#2
#2
#1
Lens Section-1
(See Page 5-6)
#2
Cabinet (R) Section
(See Page 5-10)
Ref. No.
Part No.
Description
* 101
4-154-975-01 HOLDER, AV MULTI
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Ref. No.
#1
#2
#11
5-4
Part No.
Description
2-635-562-11 SCREW (M1.7) (Black)
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
5-1-4. CABINET (TOP) SECTION
HARDWARE LIST
154
153
#11
155
MIC901
#124
CN901
152
#11
#11
#11
#3
151
#3
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
151
* 152
153
153
1-878-931-11
4-154-829-01
X-2514-483-1
X-2514-484-1
154
154
Description
FP-1131 FLEXIBLE BOARD
FRAME, SHOE
CABINET (TOP) ASSY (317) (CX500V: J)
CABINET (TOP) ASSY (318)
(EXCEPT CX500V: J)
1-487-282-11 SWITCH BLOCK, CONTROL (PS31700)
(CX500V: J)
Ref. No.
155
155
Description
X-2514-485-1 SHOE ASSY (317) (CX500V: J)
X-2514-486-1 SHOE ASSY (318) (EXCEPT CX500V: J)
0 CN901 1-818-890-11 CONNECTOR, EXTERNAL (HOT SHOE)
MIC901 1-542-711-71 MICROPHONE UNIT
#3
#11
#124
1-487-282-21 SWITCH BLOCK, CONTROL (PS31700)
(EXCEPT CX500V: J)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Part No.
5-5
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
2-599-475-01 SCREW (M1.7) (Silver)
Ver. 1.1 2009.12
The changed portions from
Ver. 1.0 are shown in blue.
5. REPAIR PARTS LIST
5-1-5. LENS SECTION-1
ns: not supplied
DISASSEMBLY
BT001
(Note 1)
#3
! : BT001
(LITHIUM STORAGE BATTERY)
Board on the mount position.
BH001
(Note 1)
208
(See page 4-40 of Level 3)
202
203
HARDWARE LIST
207
C5008
206 (Note 2)
ard
o
7B
1
T-2
S
205
#1
MM
204
ns
-08
3
#11
#1
#1
201
#1
#2
Lens Section-2
(See Page 5-8)
#1
VC-575 Section
(See Page 5-7)
#1
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
使用済み電池は，取扱指示に従って処分してください。
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Note 1: Replace the battery holder (BH001) together when replacing the lithium storage battery (BT001) on the ST217 board. (The battery holder removed once cannot be
used again.)
When mounting these parts, mount new battery holder
first and attach new lithium storage battery next.
Note 1: ST-217基板のリチウム蓄電池（BT001）を交換する場合
はバッテリホルダ（BH001）も同時に新品に交換して下
さい。（一度使用したバッテリホルダは再使用できませ
ん。）
部品取り付けの際は，先にバッテリホルダを取り付けて
からリチウム蓄電池を装着して下さい。
Note 2: Do not factory check MM-083 board in which Map Data
is installed (CX500V/CX500VE/CX505VE/CX520V/
CX520VE). The map data is erased when the factory
check is done.
Note 2: 地図データ入りM M - 0 8 3 基板 ( C X 5 0 0 V / C X 5 0 0 V E /
C X 5 0 5 V E / C X 5 2 0 V / C X 5 2 0 V E ) にはファクトリー
チェックを行わないでください。ファクトリーチェッ
クを行うと、地図データが消去されてしまいます。
• Refer to page 5-1 for mark 0.
Ref. No.
201
202
202
203
* 204
* 205
206
206
206
Part No.
Description
Ref. No.
A-1735-707-A FP-1123 FLEXIBLE BOARD, COMPLETE
A-1735-699-A ST-217 BOARD, COMPLETE
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
A-1735-700-A ST-217 BOARD, COMPLETE
(CX500/CX500E/CX520/CX520E)
A-1735-704-A FP-1120 FLEXIBLE BOARD, COMPLETE
4-154-974-01 FRAME, AV MULTI
4-154-978-01 FRAME, MS
A-1736-230-A MM-083 BOARD, COMPLETE (SERVICE)
(CX520V/CX520VE) (Note 2)
A-1736-231-A MM-083 BOARD, COMPLETE (SERVICE)
(CX520/CX520E)
A-1736-232-A MM-083 BOARD, COMPLETE (SERVICE)
(CX500/CX500E)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
206
Part No.
Description
A-1736-238-A MM-083 BOARD, COMPLETE (SERVICE)
(CX500V/CX500VE/CX505VE) (Note 2)
* 207
208
4-154-977-01 HOLDER, MS
1-878-926-11 FP-1126 FLEXIBLE BOARD
0 BH001
0 BT001
0 C5008
1-756-615-61 HOLDER, BATTERY (Note 1)
1-756-134-12 BATTERY, STORAGE, LITHIUM (Note 1)
1-116-039-21 ELECT
30uF
99%
315V
#1
#2
#3
#11
5-6
2-635-562-11
2-635-562-31
2-660-401-01
3-078-890-11
SCREW (M1.7) (Black)
SCREW (M1.7) (Black)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
5-1-6. VC-575 SECTION
DISASSEMBLY
HARDWARE LIST
#2
255
254
256
#3
253
257
258
#3
#3
V
C
-5
7
5
259
258
252
251
Ref. No.
Part No.
Description
Ref. No.
Part No.
* 251
* 252
* 253
254
* 255
4-154-965-01
4-154-962-01
4-154-963-01
A-1735-706-A
4-154-964-01
LABEL, FUSE
FRAME, VC BOTTOM
HEAT SINK, VC
FP-1122 FLEXIBLE BOARD, COMPLETE
HOLDER, USB
* 258
259
4-154-967-01 SHEET (A), VC RADIATION
A-1736-228-A VC-575 BOARD, COMPLETE (SERVICE)
(EXCEPT CX505VE)
A-1736-229-A VC-575 BOARD, COMPLETE (SERVICE)
(CX505VE)
* 256
* 257
4-154-970-01 HOLDER, HDMI
4-154-966-01 SHEET (B), VC RADIATION
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
259
#2
#3
5-7
Description
2-635-562-31 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
5. REPAIR PARTS LIST
5-1-7. LENS SECTION-2
HARDWARE LIST
306
#1
309
(including CM-103 complete board,
IC6804 (CMOS imager))
(Note)
#11
#11
310
308
307
#12
305
#1
304
#1
303
#11
#11
301
302
Note:
Note:
イメージャの交換時は4 - 3 ページの“イメージャ交換時
の注意”を必ずお読みください。
Ref. No.
Part No.
Description
301
* 302
303
304
* 305
X-2514-472-1
4-135-726-01
1-878-924-11
A-1708-647-A
4-154-671-01
HEAT SINK (R) ASSY, LENS
SHEET (CM), RADIATION
FP-1124 FLEXIBLE BOARD
LSV-1350 (SERVICE)
FRAME (L), LENS
* 306
307
308
4-154-672-01 FRAME, HDMI
1-856-034-11 OPTICAL FILTER BLOCK (OFB-03-55)
3-216-044-01 RUBBER (1270), SEAL
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Ref. No.
309
* 310
#1
#11
#12
5-8
Be sure to read “Precautions for Replacement of Imager”
on page 4-2 when changing the imager.
Part No.
Description
A-1550-292-A CMOS BLOCK ASSY (1350)
(including CM-103 complete board, IC6804 (CMOS imager))
(Note)
4-154-969-01 SHEET, CM SHIELD
2-635-562-11 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
3-080-204-21 SCREW, TAPPING, P2 (Black)
5. REPAIR PARTS LIST
5-1-8. BT PANEL SECTION
HARDWARE LIST
ns: not supplied
#1
355
354
353
352
ns
356
#11
357
#11
351
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
* 351
* 352
* 353
0 354
355
4-154-487-01
4-154-486-01
4-154-488-01
1-822-410-51
1-487-283-11
HEAT SINK, BT
FRAME, BT
RETAINER, DC TERMINAL
DC JACK (Including BH901 and J901)
SWITCH BLOCK, CONTROL (RS31700)
356
357
2-589-376-01 FOOT (395), RUBBER
X-2514-461-2 PANEL ASSY, BT
#1
#11
2-635-562-11 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-9
#11
5. REPAIR PARTS LIST
5-1-9. CABINET (R) SECTION
408
DISASSEMBLY
Hinge Section
(See Page 5-11)
HARDWARE LIST
407
406
#3
PD
-38
9
#3
#3
#2
405
409
404
410
411
403
LCD901
401
402
Ref. No.
Part No.
Description
Ref. No.
Part No.
401
402
* 403
404
404
1-480-913-11
4-154-877-01
4-154-878-01
4-154-876-01
4-154-876-11
BLOCK, LIGHT GUIDE PLATE (3.0)
CUSHION, LCD
FRAME, BACK LIGHT
CABINET (C), P (CX500V: J)
CABINET (C), P
(CX500/CX500E/CX500V: US, CND/CX500VE)
406
* 407
A-1735-703-A PD-389 BOARD, COMPLETE
4-154-880-01 SHEET, PD INSULATING
* 408
* 409
410
* 411
4-154-879-01
4-154-881-01
X-2514-497-1
4-154-882-01
404
404
* 405
4-154-876-21 CABINET (C), P (CX505VE)
4-154-876-31 CABINET (C), P
(CX520/CX520E/CX520V/CX520VE)
4-154-883-01 SHEET, LCD FLEXIBLE GUARD
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Description
FRAME, PANEL
MOLD, INNER
CABINET (M) ASSY, P
GUIDE, LCD FLEXIBLE
LCD901 A-1706-873-A FTS BLOCK ASSY (30SHGU09)
#2
2-635-562-31 SCREW (M1.7) (Black)
#3
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
5-10
5. REPAIR PARTS LIST
5-1-10. HINGE SECTION
DISASSEMBLY
ns: not supplied
HARDWARE LIST
459
#3
ns
#3
ns
#1
460
ns
SP901
ns
ns
#1
455
#1
456
ns
ns
454
457
#1
#1
453
458
#1
462
461
#1
452
451 (Note)
Note: FP-1128フレキシブル基板取付時は「HELP19」を必ずお
読みください。
Ref. No.
Part No.
Description
451
* 452
* 453
* 453
454
1-878-928-11
4-154-875-01
4-154-873-01
4-154-873-11
1-878-927-12
FP-1128 FLEXIBLE BOARD (Note)
CLAMP, LCD FLEXIBLE
COVER (C), HINGE (CX500V: J)
COVER (C), HINGE (EXCEPT CX500V: J)
FP-1127 FLEXIBLE BOARD
Note: Be sure to read “HELP19” when you install the FP-1128 flexible boards.
Ref. No.
458
459
460
461
461
455
455
456
* 456
* 457
A-1735-701-A CK-217 BOARD, COMPLETE
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
A-1735-702-A CK-217 BOARD, COMPLETE
(CX500/CX500E/CX520/CX520E)
X-2514-495-1 KNOB ASSY, GP
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
4-154-871-02 SPACER, GP (CX500/CX500E/CX520/CX520E)
4-154-874-01 COVER (M), HINGE
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-11
Part No.
Description
1-471-504-11
X-2514-494-1
4-154-831-01
1-487-284-11
MAGNET (ND5X3.5X2.4-B)
CABINET (R) ASSY
COVER, JACK
SWITCH BLOCK, CONTROL (SK31700)
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
1-487-284-21 SWITCH BLOCK, CONTROL (SK31700)
(CX500/CX500E/CX520/CX520E)
462
X-2514-496-1 HINGE ASSY, TYPE 09
SP901
1-826-837-21 SPEAKER (1.3CM)
#1
#3
2-635-562-11 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
CK-217
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1735-701-A CK-217 BOARD, COMPLETE
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
A-1735-702-A CK-217 BOARD, COMPLETE
(CX500/CX500E/CX520/CX520E)
**********************
< CAPACITOR >
C5801
1-125-777-11 CERAMIC CHIP
0.1uF
10%
10V
< CONNECTOR >
* CN5801
CN5802
CN5803
CN5804
1-821-500-11
1-821-032-81
1-794-375-21
1-816-654-61
CONNECTOR, FPC (ZIF) 45P
CONNECTOR, FPC (ZIF) 35P
PIN, CONNECTOR 2P
FFC/FPC CONNECTOR (LIF) 6P
< DIODE >
* D5801
6-501-955-01 DIODE
MAZS056G08S0
< RESISTOR >
R5803
R5804
R5805
R5806
1-218-990-81 SHORT CHIP
0
(CX500/CX500E/CX520/CX520E)
1-218-954-11 METAL CHIP
1.2K
5%
1/16W
1-218-955-11 METAL CHIP
1.5K
5%
1/16W
1-218-985-11 METAL CHIP
470K
5%
1/16W
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
< SWITCH >
* S5801
S5802
1-786-914-51 SWITCH, TACTILE
1-798-253-21 SWITCH, SLIDE
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
< SENSOR >
* SE5801 1-487-118-21 GMR SENSOR (PANEL OPEN/CLOSE)
< VARISTOR >
* VD5801 1-802-251-21 CHIP VARISTOR
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
************************************************************
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-12
Part No.
Description
Electrical parts list of the CM-103 board is
not shown.
Page 5-13 is not shown.
FP-1021 FP-1120 FP-1121 FP-1122
FP-1123 FP-1124 FP-1126 FP-1127 FP-1128 FP-1131
Ref. No.
Part No.
Description
Ref. No.
1-877-407-11 FP-1021 FLEXIBLE BOARD
(CX500V/CX500VE/CX505VE/CX520V/CX520VE)
*********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
Part No.
Description
1-878-926-11 FP-1126 FLEXIBLE BOARD
********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
1-878-927-12 FP-1127 FLEXIBLE BOARD
*********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
A-1735-704-A FP-1120 FLEXIBLE BOARD, COMPLETE
*******************************
< CONNECTOR >
* CN101 1-821-968-11 CONNECTOR, PC BOARD TO PC BOARD
* CN401 1-821-967-11 CONNECTOR, PC BOARD TO PC BOARD
************************************************************
A-1735-705-A FP-1121 FLEXIBLE BOARD, COMPLETE
*******************************
1-878-931-11 FP-1131 FLEXIBLE BOARD
*********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
< CAPACITOR >
C6501
C6502
1-165-989-11 CERAMIC CHIP
1-112-717-91 CERAMIC CHIP
10uF
1uF
10%
10%
1-878-928-11 FP-1128 FLEXIBLE BOARD
*********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
6.3V
6.3V
Electrical parts list of the MM-083 board is
not shown.
Page 5-15 is not shown.
< DIODE >
D6502
* D6503
6-502-193-01 DIODE SML-D12V8WT86SN
6-502-198-01 DIODE SML-J13RTT86
< IC >
IC6503 6-600-163-01 IC RS-770
************************************************************
A-1735-706-A FP-1122 FLEXIBLE BOARD, COMPLETE
*******************************
< CONNECTOR >
CN1001 1-821-166-21 CONNECTOR, HDMI
< LINE FILTER >
LF001 1-457-374-21 COMMON MODE CHOKE COIL
LF002 1-457-374-21 COMMON MODE CHOKE COIL
LF003 1-457-374-21 COMMON MODE CHOKE COIL
LF004 1-457-374-21 COMMON MODE CHOKE COIL
************************************************************
A-1735-707-A FP-1123 FLEXIBLE BOARD, COMPLETE
*******************************
< CONNECTOR >
CN1010 1-815-794-13 CONNECTOR (MULTIPLE)
< FERRITE BEAD >
FB001 1-400-927-31 BEAD, FERRITE (1005)
FB002 1-400-927-31 BEAD, FERRITE (1005)
************************************************************
1-878-924-11 FP-1124 FLEXIBLE BOARD
*********************
(There are not mounted electrical parts on this flexible board.)
************************************************************
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-14
PD-389
Ref. No.
Part No.
Description
Ref. No.
A-1735-703-A PD-389 BOARD, COMPLETE
**********************
< CAPACITOR >
* C6401
C6402
C6403
C6404
C6405
1-112-746-11
1-165-908-11
1-125-777-11
1-100-567-81
1-100-581-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
1uF
0.1uF
0.01uF
0.0047uF
10%
10%
10%
10%
10%
6.3V
10V
10V
25V
50V
C6407
C6408
C6409
C6410
C6411
1-112-021-91
1-112-021-91
1-112-021-91
1-112-021-91
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
2.2uF
2.2uF
2.2uF
1uF
20%
20%
20%
20%
10%
16V
16V
16V
16V
10V
C6412
C6413
C6414
C6415
C6416
1-165-908-11
1-165-908-11
1-165-908-11
1-165-908-11
1-112-021-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
1uF
1uF
2.2uF
10%
10%
10%
10%
20%
10V
10V
10V
10V
16V
C6417
C6418
C6419
1-112-021-91 CERAMIC CHIP
1-112-021-91 CERAMIC CHIP
1-112-299-91 CERAMIC CHIP
2.2uF
2.2uF
2.2uF
20%
20%
10%
16V
16V
16V
< CONNECTOR >
CN6401 1-821-032-81 CONNECTOR, FPC (ZIF) 35P
* CN6402 1-821-202-81 CONNECTOR, FPC (ZIF) 45P
* CN6403 1-821-857-51 CONNECTOR, FPC (LIF (NON-ZIF))
< COIL >
* L6401
* L6402
1-481-102-21 INDUCTOR
1-481-102-21 INDUCTOR
10uH
10uH
< TRANSISTOR >
Q6401
Q6402
8-729-427-37 TRANSISTOR
8-729-427-67 TRANSISTOR
XP411F-TXE
XP421F-TXE
< RESISTOR >
R6413
1-218-974-11 METAL CHIP
56K
5%
1/16W
< SENSOR >
* SE6401 1-487-118-11 GMR SENSOR (PANEL NOR/REV)
************************************************************
Electrical parts list of the ST-217 and VC575 boards are not shown.
Pages 5-17 to 5-22 are not shown.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-16
Part No.
Description
• EXCEPT J MODEL
to J MODEL
Checking supplied accessories.
Power cord (Mains lead)
0 1-832-121-41 (CH)
0 1-832-169-41 (UK, HK)
0 1-833-892-41 (KR)
0 1-834-482-31 (AEP, NE, E:PAL)
0 1-834-484-31 (US, CND)
0 1-834-852-11 (E:NTSC)
0 1-835-983-11 (AUS)
0 1-836-251-11 (JE)
AC Adaptor
(AC-L200C/L200D)
* Compatible in
L200C and L200D.
0 1-487-150-51
Conversion (2P) Adaptor
0 1-569-007-12 (E:NTSC, JE)
Component A/V cable
1-834-646-11
A/V connecting cable
1-823-156-61
USB cable
1-829-868-31
Operating Guide
HDR-CX500/CX500V/CX520/CX520V
4-149-356-11 (ENGLISH, SPANISH)
4-149-356-21 (FRENCH)
4-149-356-41 (TRADITIONAL CHINESE)
4-149-356-51 (KOREAN)
Operating Guide
HDR-CX500E/CX500VE/CX505VE/CX520E/CX520VE
4-149-357-11 (ENGLISH)
4-149-357-21 (FRENCH, GERMAN, ITALIAN, DUTCH)
4-149-357-31 (SPANISH, PORTUGUESE, TURKISH, GREEK)
4-149-357-41 (CZECH, HUNGARIAN, SLOVAK, POLISH)
4-149-357-51 (SWEDISH, DANISH, FINNISH, ROMANIAN)
4-149-357-61 (RUSSIAN, UKRAINIAN)
4-149-357-71 (TRADITIONAL CHINESE)
4-149-357-81 (SIMPLIFIED CHINESE)
4-149-357-91 (ARABIC, PERSIAN)
4-149-359-11 (SIMPLIFIED CHINESE)
Operating Guide (GPS)
HDR-CX500V/CX500VE/CX505VE/CX520V/CX520VE
4-156-306-11 (ENGLISH, SPANISH, FRENCH)
4-156-306-21 (GERMAN, DUTCH, PORTUGUESE, ITALIAN,
GREEK, TURKISH, POLISH, CZECH, HUNGARIAN,
SLOVAK, ROMANIAN, SWEDISH, DANISH, FINNISH)
Wireless Remote Commander
(RMT-835)
1-479-275-51
Rechargeable battery pack
(NP-FH60)
0 A-1201-668-A (CH)
0 A-1599-883-A (US, CND)
0 A-1599-884-A (EXCEPT US, CND, CH)
Handycam Handbook (PDF)
CD-ROM "Handycam
Application Software"
- Picture Motion Browser
(Software)
- PMB Guide
- Handycam Handbook
The CD-ROM supplied contains all of language version of
the Instruction Manual in pdf (Handycam Handbook.pdf) for printing.
The printed matter is not supplied. If required,
please order it with the part number below.
(Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給可能です。
HDR-CX500/CX500V/CX520/CX520V
4-149-352-01 (JAPANESE)
* 4-149-352-11 (ENGLISH)
* 4-149-352-21 (FRENCH)
* 4-149-352-31 (SPANISH)
* 4-149-352-41 (PORTUGUESE)
* 4-149-352-51 (TRADITIONAL CHINESE)
* 4-149-352-61 (KOREAN)
4-156-777-01
HDR-CX500E/CX500VE/CX505VE/CX520E/CX520VE
* 4-149-353-11 (ENGLISH)
* 4-149-354-71 (FINNISH)
* 4-149-353-21 (FRENCH)
* 4-149-354-81 (ROMANIAN)
* 4-149-353-31 (GERMAN)
* 4-149-354-91 (RUSSIAN)
* 4-149-353-41 (ITALIAN)
* 4-149-355-11 (UKRAINIAN)
* 4-149-353-51 (DUTCH)
* 4-149-355-21 (TRADITIONAL
* 4-149-353-61 (SPANISH)
CHINESE)
* 4-149-353-71 (PORTUGUESE) * 4-149-355-31 (SIMPLIFIED
* 4-149-353-81 (TURKISH)
CHINESE)
* 4-149-353-91 (GREEK)
* 4-149-355-41 (ARABIC)
* 4-149-354-11 (CZECH)
* 4-149-355-51 (PERSIAN)
* 4-149-354-21 (HUNGARIAN) * 4-149-355-61 (MALAY)
* 4-149-354-31 (SLOVAK)
* 4-149-355-71 (INDONESIAN)
* 4-149-354-41 (POLISH)
* 4-149-355-81 (THAI)
* 4-149-354-51 (SWEDISH)
* 4-149-354-61 (DANISH)
• Refer to page 5-1 for mark 0.
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-23
• J MODEL
付属品
ACアダプター
(AC-L200C/L200D)
* L200CとL200Dには
互換性があります。
0 1-487-150-51
電源コード
0 1-836-251-11
取扱説明書
4-149-356-01 (日本語)
A/V接続ケーブル
1-823-156-61
D端子A/Vケーブル
1-834-646-21
取扱説明書 (GPS)
4-156-306-01 (日本語)
リチャージャブルバッテリーパック
(NP-FH60)
0 A-1201-665-A
USBケーブル
1-829-868-31
ワイヤレスリモコン
(RMT-835)
1-479-275-51
ハンディカム ハンドブック (PDF)
CD-ROM「Handycam
Application Software」
-「Picture Motion Browser」
(ソフトウェア)
-「PMB ガイド」
-「ハンディカム ハンドブック」
印刷用の取扱説明書.pdf(ハンディカム ハンドブック.pdf)は
全ての言語が付属品のCD-ROMに含まれています。
印刷物は付属されておりません。
必要な場合は下記部品番号にて注文となります。
4-149-352-01 (日本語)
4-156-777-01
• 0マークについては，5-1ページを参照して下さい。
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
5-24E
HARDWARE LIST (1/9)
#1: M1.7 X 2.5
(Black)
2-635-562-11
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
1.7
4.0
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
4.0
5.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
3-085-397-01
1.7
5.0
#16: M1.4 X 2.5
(Silver)
2-586-337-01
#18: M1.4 X 2.5
(Silver)
2-635-591-21
2.5
#19: M1.2 X 4.0 (Tapping)
(Red)
3-086-156-21
1.7 2.2
1.4
2.5
1.4
1.4
1.5
2.5
#17: M1.7 X 1.5
(Silver)
2-586-389-01
1.7
1.7
#15: M1.4 X 1.5
(Silver)
3-062-214-01
1.7
2.5
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
4.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
1.7
3.5
1.6
#10: M1.7 X 4.0
(Silver)
2-599-475-31
1.7
1.5
1.7
1.7
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-078-890-01
1.4
3.5
1.4
2.5
#7: M1.7 X 1.6
(Black)
7-627-552-18
1.7
3.5
1.7
2.5
#6: M1.4 X 1.7
(Silver)
2-598-474-01
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
3-348-998-81
#20: M1.4 X 3.0
(Silver)
2-635-591-31
1.4
1.2
4.0
3.0
HARDWARE LIST (2/9)
#21: M1.4 X 3.0
(Black)
2-662-396-21
#22: M1.7 X 5.0 (Tapping)
(Silver)
3-083-261-01
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
1.7
1.4
5.0
3.0
#25: M1.7 X 3.0
(Black)
2-635-562-21
#35: M4.0 X 6.0 (Tapping)
(Silver)
3-975-291-02
8.0
#36: M3.0 X 6.0
(Silver)
4-886-821-11
3.0
4.0
6.0
6.0
#38: M3.0 X 20.0 (Tapping)
(Silver)
7-685-651-79
2.0
4.5
3.0
3.0
#37: M2.0 X 6.0 (Tapping)
(Black)
3-080-206-31
3.0
4.0
#34: M3.0 X 8.0
(Black)
3-077-331-41
6.0
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-102-498-01
1.2
3.5
#33: M3.0 X 6.0
(Silver)
3-077-331-21
4.0
#31: M3.0 X 4.0
(Silver)
2-102-434-01
1.4
1.4
1.4
2.0
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
2.5
#28: M1.4 X 4.0 (Tapping)
(Silver)
3-348-998-61
1.4
2.0
#29: M1.4 X 2.5
(Black)
2-662-396-01
5.5
#27: M1.4 X 2.0
(Black)
2-662-396-11
1.7
1.7
1.7
4.0
#26: M1.4 X 2.0
(Silver)
2-635-591-11
3.0
#24: B1.7 X 5.5 (Tapping)
(Black)
4-679-805-11
#39: M2.6 X 5.0 (Tapping)
(Black)
7-685-791-09
#40: M2.0 X 4.0 (Tapping)
(Silver)
7-685-851-04
3.0
2.0
6.0
2.6
20.0
5.0
2.0
4.0
HARDWARE LIST (3/9)
#41: M3.0 X 8.0 (Tapping)
(Silver)
3-065-748-01
#43: M1.7 X 4.0
(Red)
2-660-401-31
#42: M2.0 X 4.0 (Tapping)
(Silver)
7-628-253-00
4.0
4.0
#45: M1.4 X 2.5
(Silver)
2-587-151-01
1.7
2.0
3.0
8.0
#46: M1.7 X 3.0
(Red)
2-660-401-11
1.7
2.0
1.7
2.5
3.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
4.0
#48: M1.7 X 2.5
(Silver)
3-973-497-91
1.4
3.0
2.5
1.7
3.0
#47: M1.4 X 3.0 (Tapping)
(Silver)
2-665-774-01
1.4
#49: M2.0 X 4.0
(Black)
2-630-005-31
#44: M1.7 X 3.0 (Tapping)
(Silver)
3-078-890-61
#51: M2.0 X 2.5
(Silver)
3-073-686-01
#52: M2.0 X 4.0 (Tapping)
(Black)
3-080-206-11
2.0
2.0
2.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
#54: M1.75 X 6.0 (Tapping)
(Black)
3-318-203-11
6.0
6.0
2.0
3.5
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
2.0
1.7
4.0
4.0
#58: M2.0 X 6.0 (Tapping)
(Silver)
3-719-408-11
#57: M1.7 X 4.0
(Black)
7-627-852-18
2.0
1.75
2.0
5.0
#56: M2.0 X 3.5
(Silver)
3-067-187-11
#55: M2.0 X 4.0
(Silver)
2-655-582-11
#60: M2.6 X 5.0
(Black)
3-061-062-11
2.6
2.0
5.0
5.0
HARDWARE LIST (4/9)
#61: M3.0 X 10.0
(Black)
7-682-549-09
#62: M2.0 X 3.0
(Silver)
3-080-202-21
3.0
10.0
2.0
12.5
#66: M1.4 X 1.4
(Silver)
2-635-591-41
#69: M1.7 X 3.0
(Silver)
2-599-475-21
2.0
5.0
#73: M1.2 X 4.0 (Tapping)
(Black)
3-086-156-61
4.0
3.5
3.5
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
1.7
4.0
#79: M1.4X 2.0
(Silver)
2-587-151-11
#80: M1.4X 2.0
(Black)
3-279-411-01
1.4
1.4
1.2
2.0
1.7
1.7
#78: M1.4 X 3.5
(Red)
3-208-537-11
1.4
1.4
#75: M1.7 X 3.5 (Tapping)
(Silver)
2-666-551-01
6.0
#77: M1.2 X 5.0 (Tapping)
(Silver)
3-086-156-31
#72: M1.4 X 2.0
(Silver)
4-663-621-41
2.0
#74: M1.7 X 6.0 (Tapping)
(Silver)
2-666-551-31
1.2
4.0
#71: M1.4 X 2.0
(Red)
3-208-537-01
1.7
1.7
1.7
1.4
#70: M1.7 X 5.0
(Silver)
2-599-475-41
3.0
#68: M1.7 X 4.0
(Silver)
2-655-581-01
#67: M1.4 X 2.0
(Silver)
3-389-523-16
1.4
3.5
5.0
1.4
1.4
1.7
5.0
3.0
#65: M1.4 X 3.5
(Silver)
2-635-591-01
5.0
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
#63: M5.0 X 12.5
(Black)
3-060-811-21
2.0
1.4
2.0
HARDWARE LIST (5/9)
#81: M1.7 X 2.5
(Silver)
2-515-756-01
#82: M1.4 X 1.4
(Silver)
3-272-251-01
#83: M1.7 X 7.0 (Tapping)
(Black)
3-080-204-41
1.7
1.4
2.5
2.5
#90: M1.7 X 3.0
(Silver)
3-271-395-01
1.4
2.5
8.0
1.4
2.5
#99: M2.5 X 6.0 (Tapping)
(Silver)
3-776-750-02
3.8
8.0
#96: M1.4 X 2.5
(Silver)
2-587-151-21
3.0
1.7
#98: M3.0 X 8.0
(Silver)
3-077-331-01
#97: M1.4 X 2.5
(Black)
2-662-396-31
3.9
#95: M3.0 X 8.0 (Tapping)
(Black)
7-685-646-79
4.0
3.5
2.0
1.7
3.5
#94: M1.7 X 4.0
(Black)
2-515-483-31
1.7
#92: M2.0 X 3.9
(Black)
3-268-954-01
#91: M1.7 X 3.0 (Tapping)
(Silver)
2-695-434-11
3.0
1.6
5.9
1.7
2.0
#93: M1.7 X 3.5 (Tapping)
(Silver)
3-254-082-01
1.6
5.3
4.0
5.5
#88: M1.6 X 5.9 (Tapping)
(Silver)
2-689-015-01
1.7
1.7
2.0
3.0
#87: M1.6 X 5.3
(Black)
2-689-328-01
#86: M1.7 X 4.0 (Tapping)
(Silver)
2-695-434-21
#89: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-01
1.7
7.0
1.4
#85: M1.7 X 2.5
(Black)
2-515-483-11
#84: M2.0 X 3.0
(Silver)
3-072-453-11
#100: M2.0 X 6.0
(Black)
3-080-203-51
2.5
6.0
2.0
6.0
HARDWARE LIST (6/9)
#102: M2.6 X 8.0
(Black)
7-621-284-30
#101: M2.0 X 5.0
(Silver)
7-621-555-39
2.6
2.0
5.0
#105: M2.0 X 4.0
(Red)
2-891-494-31
10.0
#106: M2.0 X 6.0
(Black)
3-713-786-11
#107: M2.0 X 5.0
(Silver)
3-032-750-01
2.0
4.0
6.0
#109: M1.7 X 3.0
(Black)
2-515-483-21
#110: M2.0 X 3.0
(Black)
2-630-005-21
5.0
#117: M1.7 X 4.5 (Tapping)
(Silver)
2-695-429-31
#115: M1.4 X 3.5 (Tapping)
(Silver)
3-348-998-51
1.4
#116: M2.0 X 3.5 (Tapping)
(Silver)
2-695-435-01
2.0
1.4
3.5
#119: M2.6 X 5.0
(Black)
7-627-556-58
#120: M2.6 X 6.0
(Silver)
7-621-770-67
2.6
2.6
1.4
2.0
#112: M1.4 X 5.0
(Black)
2-178-410-11
5.0
3.5
#118: M1.4 X 2.0
(Black)
2-655-580-01
1.7
3.0
4.0
5.5
1.7
1.7
2.0
1.7
#108: M1.7 X 3.0 (Tapping)
(Black)
2-695-430-01
#111: M1.7 X 4.0 (Tapping)
(Black)
2-887-124-01
#114: M2.0 X 5.5 (Tapping)
(Silver)
2-698-464-01
#113: M1.7 X 5.0
(Black)
2-635-562-41
8.0
5.0
3.0
3.0
3.0
2.0
2.0
1.7
#104: M3.0 X 8.0
(Black)
7-682-548-09
2.6
8.0
2.0
4.5
#103: M2.6 X 10.0
(Silver)
7-685-794-09
5.0
6.0
HARDWARE LIST (7/9)
#122: M3.0 X 6.0
(Black)
7-682-547-09
#121: M2.0 X 4.0 (Tapping)
(Silver)
3-080-205-11
#123: M4.0 X 8.0
(Black)
7-682-561-09
3.0
2.0
6.0
4.0
#125: M1.4 X 3.0
(Black)
3-291-847-01
2.9 4.0
3.0
25.0
#130: M2.0 X 4.5 (Tapping)
(Silver)
3-732-817-11
3.0
12.0
3.0
#137: M1.7 X 3.0
(Black)
3-090-976-62
4.0
#136: M1.4 X 4.0 (Tapping)
(Black)
3-065-509-11
1.4
4.0
#140: M1.7 X 2.0
(Black)
2-635-562-01
#139: M1.4 X 2.0
(Silver)
2-655-579-01
1.4
1.4
3.5
6.0
2.5
#138: M1.4 X 3.5
(Silver)
4-104-078-01
2.6
2.0
2.6
1.7
#132: M2.6 X 6.0
(Black)
4-673-655-01
#135: M2.0 X 2.5
(Black)
7-627-553-28
7.0
6.0
#131: M4.0 X 12.0
(Silver)
3-452-471-01
12.0
#134: M2.6 X 7.0
(Black)
3-299-572-01
4.0
12.0
2.0
4.5
#133: M3.0 X 6.0
(Black)
3-452-484-01
3.0
#128: M4.0 X 12.0
(Black)
3-452-472-01
6.0
#129: M3.0 X 12.0
(Black)
7-682-550-09
1.7
2.0
#127: M3.0 X 25.0
(Black)
7-682-654-09
3.5
3.0
4.0
8.0
#126: M2.9 X 3.5
(Black)
3-292-616-01
1.4
#124: M1.7 X 2.0
(Silver)
2-599-475-01
2.0
1.7
2.0
HARDWARE LIST (8/9)
#141: M2.6 X 5.0 (Tapping)
(Silver)
7-685-791-01
#142: M1.4 X 2.0
(Silver)
4-111-392-01
5.0
#146: M1.4 X 2.4
(Black)
4-111-248-11
#145: M1.4 X 2.4
(Silver)
4-111-248-01
2.4
2.4
#149: M1.6 X 7.5 (Tapping)
(Silver)
4-115-505-01
7.5
#153: M1.4 X 1.5
(Silver)
3-059-718-01
1.4
#157: M1.7 X 5.0 (Tapping)
(Black)
4-132-562-01
2.6
#156: M1.4 X 4.0
(Silver)
2-635-591-61
1.7
1.4
4.0
#160: M1.4 X 3.0
(Silver)
4-139-851-01
#159: M1.4 X 4.0
(Black)
2-662-396-51
1.7
5.0
1.4
2.5
6.0
#158: M1.7 X 5.0
(Red)
2-660-401-51
1.7
5.0
1.4
#155: M1.7 X 6.0 (Tapping)
(Black)
3-080-204-31
8.0
1.5
#152: M1.4 X 2.5
(Black)
4-116-473-11
1.4
#154: M2.6 X 8.0
(Silver)
7-627-556-97
1.4
3.0
#151: M1.4 X 1.4
(Silver)
3-272-251-11
3.0
1.7
1.4
3.5
#150: M1.4 X 3.0
(Black)
4-105-150-01
1.6
#148: M1.7 X 3.0
(Silver)
3-057-082-21
#147: M1.4 X 3.5
(Black)
2-662-396-41
1.4
1.4
1.2
2.0
2.0
1.4
1.4
1.4
2.6
#144: M1.4 X 1.2
(Silver)
4-111-392-21
#143: M1.4 X 2.0
(Black)
4-111-392-11
1.4
4.0
1.4
3.0
HARDWARE LIST (9/9)
#162: M1.6 X 8.5 (Tapping)
(Black)
4-144-032-01
#161: M1.4 X 3.0
(Black)
4-139-852-01
8.5
#165: M1.7 X 3.0 (Tapping)
(Silver)
2-695-434-31
3.0
#169: M1.4 X 2.5
(Silver)
4-111-392-51
1.4
2.5
2.0
3.9
#167: M1.7 X 4.0 (Tapping)
(Black)
2-698-496-01
1.7
1.7
3.0
5.5
#166: M1.7 X 3.0 (Tapping)
(Silver)
3-271-395-11
#164: M2.0 X 3.9
(Black)
3-268-954-11
2.0
1.6
1.4
3.0
#163: M2.0 X 5.5 (Tapping)
(Silver)
2-695-575-11
#168: M1.4 X 2.5
(Black)
4-111-392-41
1.7
4.0
1.4
2.5
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE
/CX520/CX520E/CX520V/CX520VE
RMT-835
2
LEVEL
SERVICE MANUAL
Ver. 1.1 2009.12
SUPPLEMENT-1
US Model
Canadian Model
AEP Model
UK Model
North European Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
File this supplement with the service manual previously issued.
(09-336)
• Change of Repair Parts List
• Addition of HELP
5. REPAIR PARTS LIST
&: Points added portion
5-1. EXPLODED VIEWS
Page
Before change
After change
5-1-9. CABINET (R) SECTION
5-1-9. CABINET (R) SECTION
LCD901
LCD901
5-10
412
401
401
HELP20
Ref. No.
Part No.
Description
Ref. No.
Part No.
* 412
4-156-994-01 SHEET (400), SOLDER PROTECTION
Description
)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
9-852-714-81
Sony EMCS Co.
2009L0800-1
©2009.12
Published by Tokai TEC
&: Points added portion
Page
Before change
After change
5-1-10. HINGE SECTION
5-1-10. HINGE SECTION
463 HELP21
#3
#3
#3
#3
5-11
455
455
Ref. No.
Part No.
Description
Ref. No.
Part No.
* 463
4-175-496-01 TAPE (AS), PROTECTION
Description
)
• ADDITION OF HELP
HELP20
HELP21
SHEET (400), SOLDER PROTECTION
APPLYING POSITION
TAPE (AS), PROTECTION
APPLYING POSITION
Under the flexible
board edge
LCD901
with
Light guide plate (3.0) block
BACKLIGHT FLEXIBLE BOARD
FP-1127 FLEXIBLE
BOARD
CONTROL
SWITCH
BLOCK
(SK31700)
Applying standards
TAPE (AS),
PROTECTION
Inside of the flexible
board edge
SHEET (400),
SOLDER PROTECTION
(Covers the soldered portion)
CN5804
CN5801
LCD FLEXIBLE BOARD
CK-217 BOARD
Applying standards
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
—2—
Hide CN5801
Reverse
985271432.pdf
Revision History
Ver.
Date
History
1.0
2009.07
Official Release
1.1
2009.12
Supplement-1
(S1 09-336)
HDR-CX500/CX500E/CX500V/CX500VE/CX505VE/
CX520/CX520E/CX520V/CX520VE_L2
Contents
—
• Change of Repair Parts List
• Addtion of HELP
• Additon of Service Note
• Correction of Block Diagram
• Correction of Repair Parts List
S. M. Revised: Page 1-1, 1-8, 3-4, 5-6
S.M. Rev.
issued
—
Yes