Download HDR-CX6EK/CX7/CX7E/CX7K/CX7EK - EXIT EQUIPMENT

HDR-CX6EK/CX7/CX7E/CX7K/CX7EK
RMT-835
SERVICE MANUAL
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
Ver. 1.2 2007.11
Revision History
Revised-1
Replace the previously issued
SERVICE MANUAL 9-852-210-31
with this Manual.
Photo: HDR-CX7
Link
SPECIFICATIONS
DISASSEMBLY
SCHEMATIC DIAGRAMS
MODEL INFORMATION TABLE
BLOCK DIAGRAMS
PRINTED WIRING BOARDS
SERVICE NOTE
FRAME SCHEMATIC DIAGRAM
REPAIR PARTS LIST
• Precaution on Replacing the VC-493 Board
• Precaution on Replacing the Holder (MS)
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
DIGITAL HD VIDEO CAMERA RECORDER
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
9-852-210-32
Sony EMCS Co.
2007K0500-1
© 2007.11
Published by Kohda TEC
These specifications are extracted from instruction
manual of HDR-CX6EK/CX7E/CX7EK.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
AC Adaptor AC-L200/L200B
Video compression format
AVCHD (HD)/MPEG2 (SD)/JPEG (Still
images)
Audio compression format
Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator
Audio/Video output
10-pin connector
Video signal: 1 Vp-p, 75 : (ohms)
Luminance signal: 1 Vp-p, 75 : (ohms)
Chrominance signal: 0.3 Vp-p, 75 : (ohms)
Audio signal: 327 mV (at load impedance 47
k: (kilohms)), Output impedance with less
than 2.2 k: (kilohms)
HDMI OUT jack
HDMI Type C mini connector
Power requirements
AC 100 V - 240 V, 50/60 Hz
Current consumption
0.35 - 0.18 A
Video signal
PAL color, CCIR standards
1080/50i specification
Recording format
Movie (HD): AVCHD 1080/50i
Movie (SD): MPEG2-PS
Still image: Exif Ver.2.2*1
Image device
6.3 mm (1/2.9 type) CMOS sensor
Recording pixels (still image, 4:3):
Max. 6.1 mega (2 848 × 2 136) pixels*2
Gross: Approx. 3 200 000 pixels
Effective (movie, 16:9):
2 280 000 pixels
Effective (movie, 4:3):
1 710 000 pixels
Effective (still image, 16:9):
2 280 000 pixels
Effective (still image, 4:3):
3 040 000 pixels
Lens
Carl Zeiss Vario-Sonnar T
10 × (Optical), 20 × (Digital)
Focal length
F1.8 ~ 2.9
Filter diameter: 37 mm (1 1/2 in.)
f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When
converted to a 35 mm still camera
For movies: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.)
(16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.)
(4:3)
For still images: 40 ~ 400 mm (1 5/8 ~ 15 3/4
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.)
(4:3)
Color temperature
[AUTO], [ONE PUSH],
[INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)
Minimum illumination
2 lx (lux) ([AUTO SLW SHUTTR] [ON],
Shutter speed 1/25 sec)
0 lx (lux) (during NightShot function)
*1 “Exif” is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
*2 The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing
system (new Enhanced Imaging
Processor) allows still image resolution
equivalent to the sizes described.
LCD screen
Image
6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number
211 200 (960 × 220)
General
Power requirements
DC 6.8 V/7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
Average power consumption
During camera recording using the LCD with
normal brightness:
HD: 4.3 W
SD: 3.8 W
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Dimensions (approx.)
69 × 67 × 129 mm
(2 3/4 × 2 3/4 × 5 1/8 in.) (w/h/d)
including the projecting parts
69 × 67 × 131 mm
(2 3/4 × 2 3/4 × 5 1/4 in.) (w/h/d)
including the projecting parts, and the NPFH60 rechargeable battery pack attached
Mass (approx.)
370 g (13 oz) main unit only
450 g (15 oz) including the NP-FH60
rechargeable battery pack, and a “Memory
Stick PRO Duo”
Handycam Station DCRA-C191
Input/Output connectors
Audio/Video output
10 pin connector
Video signal: 1 Vp-p, 75 : (ohms)
Luminance signal: 1 Vp-p, 75 : (ohms)
Chrominance signal: 0.3 Vp-p, 75 : (ohms)
Audio signal: 327 mV (at load impedance 47
k: (kilohms)), Output impedance with less
than 2.2 k: (kilohms)
COMPONENT OUT jack
Y: 1 Vp-p, 75 : (ohms)
PB/PR, CB/CR: +/- 350 mV, 75 : (ohms)
USB jack
mini-B
HDR-CX6EK: You cannot input signals to
your camcorder through this jack.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—2—
Power consumption
18 W
Output voltage
DC 8.4 V*
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Dimensions (approx.)
48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
excluding the projecting parts
Mass (approx.)
170 g (6.0 oz) excluding the mains lead
* See the label on the AC Adaptor for other
specifications.
Rechargeable battery pack NP-FH60
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
7.2 Wh (1 000 mAh)
Dimensions (approx.)
31.8 × 33.3 × 45.0 mm
(1 5/16 × 1 5/16 × 1 13/16 in.) (w/h/d)
Mass (approx.)
80 g (2.9 oz)
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Type
Lithium ion
Design and specifications are subject to change
without notice.
• Your camcorder is produced under the license of
Dolby Laboratories.
These specifications are extracted from instruction
manual of HDR-CX7/CX7K.
ENGLISH
JAPANESE
SPECIFICATIONS
System
Input/Output connectors
AC Adaptor AC-L200/L200B
Video compression format
AVCHD (HD)/MPEG2 (SD)/JPEG (Still
images)
Audio/Video output
10-pin connector
Video signal: 1 Vp-p, 75 : (ohms)
Luminance signal: 1 Vp-p, 75 : (ohms)
Chrominance signal: 0.286 Vp-p, 75 :
(ohms)
Audio signal: 327 mV (at load impedance 47
k: (kilohms)), Output impedance with less
than 2.2 k: (kilohms)
Power requirements
AC 100 V - 240 V, 50/60 Hz
HDMI OUT jack
HDMI Type C mini connector
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
LCD screen
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Image
6.7 cm (2.7 type, aspect ratio 16:9)
Total dot number
211 200 (960 × 220)
Dimensions (approx.)
48 × 29 × 81 mm
(1 15/16 × 1 3/16 × 3 1/4 in.) (w/h/d)
excluding the projecting parts
General
Mass (approx.)
170 g (6.0 oz) excluding the power cord
Audio compression format
Dolby Digital 2/5.1ch
Dolby Digital 5.1 Creator
Video signal
NTSC color, EIA standards
1080/60i specification
Recording format
Movie (HD): AVCHD 1080/60i
Movie (SD): MPEG2-PS
Still image: Exif Ver.2.2*1
Image device
6.3 mm (1/2.9 type) CMOS sensor
Recording pixels (still image, 4:3):
Max. 6.1 mega (2 848 × 2 136) pixels*2
Gross: Approx. 3 200 000 pixels
Effective (movie, 16:9):
2 280 000 pixels
Effective (movie, 4:3):
1 710 000 pixels
Effective (still image, 16:9):
2 280 000 pixels
Effective (still image, 4:3):
3 040 000 pixels
Lens
Carl Zeiss Vario-Sonnar T
10 × (Optical), 20 × (Digital)
Focal length
F1.8 ~ 2.9
Filter diameter: 37 mm (1 1/2 in.)
f=5.4 ~ 54 mm (7/32 ~ 2 1/4 in.) When
converted to a 35 mm still camera
For movies: 40 ~ 400 mm (1 5/8 ~ 15 3/4 in.)
(16:9), 49 ~ 490 mm (1 15/16 ~ 19 3/8 in.)
(4:3)
For still images: 40 ~ 400 mm (1 5/8 ~ 15 3/4
in.) (16:9), 37 ~ 370 mm (1 1/2 ~ 14 5/8 in.)
(4:3)
Color temperature
[AUTO], [ONE PUSH],
[INDOOR] (3 200 K),
[OUTDOOR] (5 800 K)
Minimum illumination
2 lx (lux) ([AUTO SLW SHUTTR] [ON],
Shutter speed 1/30 sec)
0 lx (lux) (during NightShot function)
*1 “Exif” is a file format for still images,
established by the JEITA (Japan
Electronics and Information Technology
Industries Association). Files in this
format can have additional information
such as your camcorder’s setting
information at the time of recording.
*2 The unique pixel array of Sony’s ClearVid
CMOS sensor and image processing
system (new Enhanced Imaging
Processor) allows still image resolution
equivalent to the sizes described.
Current consumption
0.35 - 0.18 A
Power consumption
18 W
Output voltage
DC 8.4 V*
Power requirements
DC 6.8 V/7.2 V (battery pack)
DC 8.4 V (AC Adaptor)
* See the label on the AC Adaptor for other
specifications.
Average power consumption
During camera recording using the LCD with
normal brightness:
HD: 4.4 W
SD: 3.8 W
Rechargeable battery pack NP-FH60
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Storage temperature
-20 °C to + 60 °C (-4 °F to + 140 °F)
Dimensions (approx.)
69 × 67 × 129 mm
(2 3/4 × 2 3/4 × 5 1/8 in.) (w/h/d)
including the projecting parts
69 × 67 × 131 mm
(2 3/4 × 2 3/4 × 5 1/4 in.) (w/h/d)
including the projecting parts, and the NPFH60 rechargeable battery pack attached
Mass (approx.)
370 g (13 oz) main unit only
450 g (15 oz) including the NP-FH60
rechargeable battery pack, and a “Memory
Stick PRO Duo”
Handycam Station DCRA-C191
Input/Output connectors
Audio/Video output
10 pin connector
Video signal: 1 Vp-p, 75 : (ohms)
Luminance signal: 1 Vp-p, 75 : (ohms)
Chrominance signal: 0.286 Vp-p, 75 :
(ohms)
Audio signal: 327 mV (at load impedance 47
k: (kilohms)), Output impedance with less
than 2.2 k: (kilohms)
COMPONENT OUT jack
Y: 1 Vp-p, 75 : (ohms)
PB/PR, CB/CR: +/- 350 mV, 75 : (ohms)
USB jack
mini-B
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—3—
Maximum output voltage
DC 8.4 V
Output voltage
DC 7.2 V
Capacity
7.2 Wh (1 000 mAh)
Dimensions (approx.)
31.8 × 33.3 × 45.0 mm
(1 5/16 × 1 5/16 × 1 13/16 in.) (w/h/d)
Mass (approx.)
80 g (2.9 oz)
Operating temperature
0 °C to + 40 °C (32 °F to 104 °F)
Type
Lithium ion
Design and specifications are subject to change
without notice.
• Your camcorder is produced under the license of
Dolby Laboratories.
ENGLISH
JAPANESE
概略仕様
システム
液晶画面
映像圧縮方式
AVCHD（HD）/MPEG2（SD）/JPEG（静止
画）
画面サイズ
6.7 cm（2.7型、アスペクト比16:9）
音声圧縮方式
Dolby Digital2/5.1ch
ドルビーデジタル5.1クリエーター搭載
映像信号
NTSCカラー、EIA標準方式
1080/60i方式
リチャージャブルバッテリーパック
NP-FH60
最大電圧
DC 8.4 V
総ドット数
211 200ドット
横960×縦220
公称電圧
DC 7.2 V
容量
電源部、
その他
7.2 Wh（1 000 mAh）
電源電圧
バッテリー端子入力 6.8 V/7.2 V
DC端子入力 8.4 V
最大外形寸法
約31.8×33.3×45.0 mm
（幅×高さ×奥行き）
静止画記録方式
消費電力
液晶画面の明るさ標準：
HD 4.4 W、SD 3.8 W
質量
約80 g
撮像素子
動作温度
0℃∼+40 ℃
動画記録方式
動画HD: AVCHD 1080/60i
動画SD: MPEG2-PS
Exif Ver.2.2*1
6.3mm（1/2.9型）CMOSセンサー
記録画像数：静止画時最大610万画素相当*2
（2 848×2 136）
（4:3時）
総画素数：約320万画素
動画時有効画素数（16：9モード）
：約228万画
素
動画時有効画素数（4：3モード）
：約171万画
素
静止画時有効画素数（16：9モード）
：約228万
画素
静止画時有効画素数（4：3モード）
：約304万
画素
ズームレンズ
カール ツァイス バリオゾナーT
10倍（光学）、20倍（デジタル）
フィルター径37mm
F1.8∼2.9
f=5.4∼54mm
35mmカメラ換算では
動画撮影時：
40∼400mm（16:9モード）
（4:3モードでは49∼490mm）
静止画撮影時：
40∼400ｍｍ（16:9モード）
（4:3モードでは37∼370mm）
色温度切り換え
［オート］
［ワンプッシュ］、
、
［屋内］
（3 200
［屋外］
（5 800 K）
K）、
最低被写体照度
（［オートスロシャッタ］
［入］、
5 lx（ルクス）
［シャッタースピード］
1/30秒）
（NightShot時）
0 lx（ルクス）
*1（社）電子情報技術産業協会（JEITA）にて
制定された、
撮影情報などの付帯情報を追
加することができる静止画用のファイル
フォーマット。
*2 ソニー独自のクリアビッドCMOSセン
サーの画素配列と画像処理システム新エ
ンハンスドイメージングプロセッサーに
より、
静止画は表記の記録サイズを実現し
ています。
入/出力端子
A/V OUT端子
10ピン特殊コネクター
映像：1 Vp-p、
75 Ω
Y出力
1 Vp-p、75 Ω
C出力
0.286 Vp-p、75 Ω
音声：327 mV（47 kΩ負荷時）
、
出力インピー
ダンス2.2 kΩ以下
HDMI OUT端子
HDMIタイプCミニ端子
保存温度
−20℃∼+60 ℃
外形寸法
69×67×129 mm
（突起部を含む）
（幅×高さ×奥行き）
69×67×131 mm
（突起部含む、
付属バッテリーパックNPFH60装着状態）
（幅×高さ×奥行き）
本体質量
約370 g（本体のみ）
撮影時総質量
約450 g（バッテリーパックNP-FH60、
“メ
モリースティック PRO デュオ”含む）
ハンディカムステーション
DCRA-C190
入/出力端子
A/V OUT端子
10ピン特殊コネクター
映像：1 Vp-p、75 Ω
Y出力
1 Vp-p、75 Ω
C出力
0.286 Vp-p、75 Ω
音声：327 mV（47 kΩ負荷時）、出力インピー
ダンス2.2 kΩ以下
COMPONENT OUT端子
D1/D3映像：コンポーネントビデオ端子
Y：1 Vp-p、75 Ω
PB/PR, CB/CR: ±350 mV, 75 Ω
USB端子
mini-B
ACアダプター AC-L200/L200B
電源
AC 100 Vー240 V、50/60 Hz
消費電力
18 W
定格出力
DC 8.4 V *
動作温度
0 ℃∼+40 ℃
保存温度
−20 ℃∼+60 ℃
外形寸法
約 48×29×81 mm
（最大突起部をのぞく）
（幅×高さ×奥行き）
質量
約170 g（本体のみ）
* その他の仕様については AC アダプターのラ
ベルをご覧ください。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—4—
使用温度
0 ℃∼+40 ℃
使用電池
Li-ion
本機の仕様および外観は、改良のため予告なく変
更することがありますが、ご了承ください。
• ドルビーラボラトリーズからの実施権に基づ
き製造されています。
Model information table
Model
Destination
Color system
Data CAM → PC
copy PC → CAM
Supplied accessory
“Memory Stick PRO Duo”
HDR-CX6EK
AEP, UK
HDR-CX7
US, CND, J
HDR-CX7E
CH
HDR-CX7K
E, KR, JE
HDR-CX7EK
AEP, E, AUS, HK, JE
PAL
a
NTSC
a
PAL
a
NTSC
a
PAL
a
×
a
a
a
a
a
×
×
a
a
• Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
MX : Mexican model
NE : North European model
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—5—
ENGLISH
JAPANESE
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1.
2.
3.
4.
5.
6.
Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
Check the B+ voltage to see it is at the values specified.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—6—
ENGLISH
JAPANESE
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
サービス，点検時には次のことにご注意下さい。
6. フレキシブルプリント基板の取扱いについて
1. 注意事項をお守りください。
サービスのとき特に注意を要する個所については，
キャビネット，シャーシ，部品などにラベルや捺印で
• コテ先温度を270℃前後にして行なって下さい。
• 同一パターンに何度もコテ先を当てないで下さい。
注意事項を表示しています。これらの注意書き及び取
扱説明書等の注意事項を必ずお守り下さい。
（3回以内）
• パターンに力が加わらないよう注意して下さい。
2. 指定部品のご使用を
セットの部品は難燃性や耐電圧など安全上の特性を
7. 無鉛半田について
無鉛半田を使用している基板には，無鉛（Lead Free）を意
持ったものとなっています。従って交換部品は，使用
されていたものと同じ特性の部品を使用して下さい。
味するレッドフリーマークがプリントされています。
（注意：基板サイズによっては，無鉛半田を使用して
特に回路図，部品表に0印で指定されている安全上重要
な部品は必ず指定のものをご使用下さい。
いてもレッドフリーマークがプリントされて
いないものがあります）
3. 部品の取付けや配線の引きまわしはもとどおりに
安全上，チューブやテープなどの絶縁材料を使用した
：レッドフリーマーク
無鉛半田には，以下の特性があります。
り，プリント基板から浮かして取付けた部品がありま
す。また内部配線は引きまわしやクランパによって発
• 融点が従来の半田よりも約40℃高い。
従来の半田こてをそのまま使用することは可能です
熱部品や高圧部品に接近しないよう配慮されています
ので，これらは必ずもとどおりにして下さい。
が，少し長めにこてを当てる必要があります。
温度調節機能のついた半田こてを使用する場合，約
4. サービス後は安全点検を
サービスのために取外したネジ，部品，配線がもとど
350℃に設定して下さい。
注意： 半田こてを長く当てすぎると，基板のパター
おりになっているか，またサービスした個所の周辺を
劣化させてしまったところがないかなどを点検し，安
ン（銅箔）がはがれてしまうことがあります
ので，注意して下さい。
• 粘性が強い
従来の半田よりも粘性が強いため，IC端子などが半田
全性が確保されていることを確認して下さい。
5. チップ部品交換時の注意
• 取外した部品は再使用しないで下さい。
• タンタルコンデンサのマイナス側は熱に弱いため交
ブリッジしないように注意して下さい。
• 従来の半田と混ぜて使用可能
無鉛半田には無鉛半田を追加するのが最適ですが，
従来の半田を追加しても構いません。
換時は注意して下さい。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—7—
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. POWER SUPPLY DURING REPAIRS
In this unit, about 10 seconds after power is supplied to the battery terminal using the regulated power supply (8.4 V), the power is shut off so
that the unit cannot operate.
These following method is available to prevent this.
Method:
Use the AC power adaptor (AC-L200/L200B).
1-2. PRECAUTION ON REPLACING THE VC-493 BOARD
DESTINATION DATA
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
Refer to Service Manual ADJ, and perform “DESTINATION DATA WRITE”.
USB SERIAL No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
Refer to Service Manual ADJ, and perform “USB SERIAL No. INPUT”.
1-3. SELF-DIAGNOSIS FUNCTION
1-3-1. Self-diagnosis Function
1-3-2. Self-diagnosis Display
When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.
When problems occur while the unit is operating, the counter of the
LCD screen shows a 4-digit display consisting of an alphabet and
numbers, which blinks at 3.2 Hz. This 5-character display indicates
the “repaired by:”, “block” in which the problem occurred, and
“detailed code” of the problem.
LCD screen
C:31:11
Blinks at 3.2Hz
C
Repaired by:
C : Corrected by customer
H : Corrected by dealer
E : Corrected by service
engineer
31
Block
11
Detailed Code
Refer to “1-3-3. Self-diagnosis Code Table”.
Indicates the appropriate
step to be taken.
E.g.
31 ....Reload the tape.
32 ....Turn on power again.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-1
ENGLISH
JAPANESE
1-3-3. Self-diagnosis Code Table
Repaired by:
Self-diagnosis Code
Block
Function
Detailed
Code
Symptom/State
C
0
4
0
0
C
1
3
0
1
C
1
3
0
2
Access error
C
3
2
6
0
Difficult to adjust forcus
(Cannot initialize focus)
E
2
0
0
0
EEPROM data are rewritten.
E
6
1
1
0
Zoom operations fault
(Cannot initialize zoom lens.)
E
6
1
1
1
E
6
2
0
0
E
6
2
0
1
E
6
2
0
2
E
6
2
0
3
E
6
2
1
0
E
6
2
1
1
E
6
2
1
2
E
6
2
2
0
E
9
1
0
1
E
9
4
0
0
Correction
Non-standard battery is used.
“Memory Stick Duo” is unformatted.
“Memory Stick Duo” is broken.
The abnormalities in initialization of
the focus lens and the abnormalities in
initialization of the zoom lens occurred
simultaneously.
Handshake correction function does not
work well. (With PITCH angular
velocity sensor output stopped.)
Handshake correction function does not
work well. (With YAW angular velocity
sensor output stopped.)
Abnormality of IC for steadyshot.
Use the InfoLITHIUM battery.
Format the “Memory Stick Duo”.
Insert a new “Memory Stick Duo”.
Remove the power source. Reconnect it again and operate your
camcorder again.
Retry turn the power on by the power switch. If it does not
recover, check the focus MR sensor of lens block (pin qh, qk of
CN5302 on the LD-222 board). If it is OK, check the focus
motor drive IC (IC5404 on the LD-222 board).
Make EEPROM data correct value.
Inspect the lens block zoom MR sensor (pin w;, wa of CN5302
on the LD-222 board) when zooming is performed when the
zoom lever is operated, and the zoom motor drive circuit
(IC5404 on the LD-222 board) when zooming is not performed.
Check both C : 32 : 60 and E : 61 : 10 of the self-diagnosis code.
Inspect PITCH angular velocity sensors (SE7202 on the CM-077
board) peripheral circuits.
Inspect YAW angular velocity sensors (SE7201 on the CM-077
board) peripheral circuits.
Refer to “1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot]
Occurred”.
IC for steadyshot and micro controller
Inspect the steadyshot circuit (IC5703 on the LD-222 board).
communication abnormality among.
Refer to “1-4-2. E : 62 : 10 [Shift Lens Initializing Failure]
Shift lens initializing failure.
Occurred”.
Refer to “1-4-3. E : 62 : 11 [Shift Lens Overheating (Pitch)]
Shift lens overheating (Pitch).
Occurred”.
Refer to “1-4-4. E : 62 : 12 [Shift Lens Overheating (Yaw)]
Shift lens overheating (Yaw).
Occurred”.
Refer to “1-4-5. E : 62 : 20 [Abnormality of Thermistor]
Abnormality of thermistor.
Occurred”.
Abnormality when flash is being charged. Checking of flash unit or replacement of flash unit. (Note 1)
Fault of writing to or erasing the
Inspect the flash memory (IC2201 on the VC-493 board).
flashmemory
(Note 2)
Note 1: After repair, be sure to perform “1-5. PROCESS AFTER FIXING FLASH ERROR”.
Note 2: Refer to Service Manual, ADJ (“1-3. DESTINATION DATA WRITE”).
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-2
ENGLISH
JAPANESE
1-4. METHOD OF COPING WITH SHIFT LENS ERROR
LD-222 BOARD (SIDE A)
about 330 msec
Note: The length of low section will vary a little depending on the
conditions.
Fig. 2
Change in output voltage of R5792 on the LD-222 board
VC-493 BOARD (SIDE A)
R5792
R5737
IC5703
R5721
IC1803
Fig. 1
Measurement points on the LD-222 board
R1846
Fig. 3
Measurement points on the VC-493 board
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-3
ENGLISH
JAPANESE
1-4-1. E : 62 : 02 [Abnormality of IC for Steadyshot] Occurred
Order
Procedure
1
Turn the power OFF.
2
While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the
power ON to check that the output voltage immediately after the power on change as shown in Fig. 2.
3
If the output voltage change as shown in Fig. 2, replace the lens block (Note). If it does not change as shown in Fig. 2, inspect
the camera control circuit (IC1803 of VC-493 board) periphery.
Note: When the lens block was replaced, execute a necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld
operation.
1-4-2. E : 62 : 10 [Shift Lens Initializing Failure] Occurred
Inspection method:
1) Perform the “Check 1” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2) If “EEPROM Error” is displayed while executing the “Check 1”, inspect the EEPROM (IC1804 of VC-493 board).
3) Turn the power OFF and ON again.
4) Check that no error occurs. If an error occurs, replace the lens block (Note 2).
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-4-3. E : 62 : 11 [Shift Lens Overheating (Pitch)] Occurred
Inspection method:
1) Perform the “Check 2” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2) Check if the shift lens moves while executing the “Check 2”. If the shift lens does not move, replace the lens block (Note 2). When the
shift lens moved, proceed to the order 3.
3) While executing the “Check 2”, measure with an oscilloscope the output voltage of R5721 in the periphery of IC5703 on the LD-222
board to check the output voltage varies.
4) If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 5.
5) Turn the power OFF.
6) While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the power ON
to check that the output voltage immediately after the power on change as shown in Fig. 2.
7) If the output voltage changes as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
1-4-4. E : 62 : 12 [Shift Lens Overheating (Yaw)] Occurred
Inspection method:
1) Perform the “Check 3” of “Shift Lens Check” (Note 1).
Note 1: For “Shift Lens Check”, refer to Service Manual, ADJ (“7. Shift Lens Check” of “3-2. SERVICE MODE”).
2) Check if the shift lens moves while executing the “Check 3”. If the shift lens does not move, replace the lens block (Note 2). When the
shift lens moved, proceed to the order 3.
3) While executing the “Check 3”, measure with an oscilloscope the output voltage of R5737 in the periphery of IC5703 on the LD-222
board to check the output voltage varies.
4) If the output voltage does not vary, replace the lens block (Note 2). When the output voltage varied, proceed to the order 5.
5) Turn the power OFF.
6) While measuring with an oscilloscope the output voltage of R5792 in the periphery of IC5703 on the LD-222 board, turn the power ON
to check that the output voltage immediately after the power on change as shown in Fig. 2.
7) If the output voltage changes as shown in Fig. 2, replace the lens block (Note 2). If it does not change as shown in Fig. 2, inspect the
camera control circuit (IC1803 of VC-493 board) periphery.
Note 2: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld operation.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-4
ENGLISH
JAPANESE
1-4-5. E : 62 : 20 [Abnormality of Thermistor] Occurred
Order
Procedure
1
Turn the power ON.
2
Check that R1846 in the periphery of IC1803 on the VC-493 board is 0 Ω and energizes. If it is not energizes, replace the R1846.
When R1846 is 0 Ω and energizes, replace the lens block (Note).
3
Check that no error occurs, after replacing the lens block and performing the necessary adjustment. If an error occurs, inspect
the camera control circuit (IC1803 of VC-493 board) periphery.
Note: When the lens block was replaced, execute the necessary adjustment items referring to Service Manual, ADJ.
After the adjustment, make sure with the STEADYSHOT turned ON that the steadyshot functions appropriately in the handheld
operation.
1-5. PROCESS AFTER FIXING FLASH ERROR
When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash
is changed automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by execution of “Clear All record-data”.
Note: For “Clear All record-data”, refer to Service Manual, ADJ (“6. Record Data” of “3-2. SERVICE MODE”).
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-5
ENGLISH
JAPANESE
1-6. PRECAUTION ON REPLACING THE
HOLDER (MS)
1-6-1. Precaution on ordering the Holder (MS)
Note: After replacing the holder (MS), the serial number for it will
be changed to the one exclusive for service use.
Inform a customer of the serial number change and change
the serial number in the repair data.
The model display adopts the laser printing method.
Therefore, the holder (MS) for replacement differs depending on
the destination.
As similar displays are provided, choose the suitable one for order.
HDR-CX7 (J)
HDR-CX7E (CH)
HDR-CX7EK (E, HK, AUS, JE)
Serial No.
Serial No.
Part No.
Description
Part No.
A-1334-454-A HOLDER (CX7-J1), SERVICE (MS)
HDR-CX7 (US)
Serial No.
Part No.
Description
A-1334-457-A (CX7E-CN2), SERVICE (MS)
HDR-CX7K (E, JE)
Description
A-1334-460-A HOLDER (CX7KE-E34), (MS)
HDR-CX7EK (AEP)
Serial No.
Serial No.
Serial No.
Part No.
Description
Part No.
A-1334-455-A HOLDER (CX7-U2), SERVICE (MS)
HDR-CX7 (CND)
Part No.
Description
A-1334-458-A (CX7K-E23), SERVICE (MS)
HDR-CX7K (KR)
Description
A-1334-461-A HOLDER (CX7KE-CEN), (MS)
HDR-CX6EK (AEP, UK)
Serial No.
Serial No.
Serial No.
Part No.
Description
A-1334-456-A HOLDER (CX7-CA2), SERVICE
(MS)
Part No.
Description
A-1334-459-A HOLDER (CX7K-KR2), SERVICE
(MS)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-6
Part No.
Description
A-1334-462-A HOLDER (CX6EK-CEH), (MS)
ENGLISH
JAPANESE
1-6-2. Precaution on Replacing the Holder (MS) for J Models
The year of manufacture on the labels should be the same as the previous Holder (MS) (circled portions shown on the below).
Example: For the figure below, attach the “Made of 07 years” label.
* The replacement label and “inset (how to affix)” are supplied together with holder (MS) for service.
* Manufacturing
year
* Affix the label
1-6-3. Precaution on Replacing the Holder (MS) for US Models
The date of manufacture and the manufacturer on the labels should be the same as the previous Holder (MS) (circled portions shown on the
below).
Example: For the figure below, attach the “7A” and “SKD” labels.
* The replacement labels and “inset (how to affix)” are supplied together with holder (MS) for service.
* The layout of the print has changed so that a new holder (MS) for US may widen the area that sticks labels on.
Previous Holder (MS)
New Holder (MS)
* Factory
Factory
Manufacturing year
* Manufacturing
year
* Affix the label
1-6-4. Precaution on Replacing the Holder (MS) for KR Models
The date of manufacture on the labels should be the same as the previous Holder (MS) (circled portions shown on the below).
Example: For the figure below, attach the “2007.5” label.
* The replacement label and “inset (how to affix)” are supplied together with holder (MS) for service.
* Manufacturing
year
* Affix the label
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-7
1. SERVICE NOTE
ENGLISH
JAPANESE
1-1. 修理時の電源供給について
本機では，安定化電源（8.4Vdc）からバッテリ端子に電源を供給した場合，約10秒後にシャットオフし，動作しなくなりま
す。
これを避けるため，下記の方法を用いてください。
方法：
DC入力端子を使用する。（ACアダプタ（AC-L200/L200B）を使用する。）
1-2. VC-493基板交換時の注意
仕向けデータ
補修用基板と交換する時，補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
ADJ編を参照して，「DESTINATION DATA WRITE」を行ってください。
USBシリアルNo.
セットは，1台毎に異なる固有のID（USB Serial No.）を書き込んだ後，出荷されています。
新品の補修用基板には，このIDが書き込まれていないので，基板交換後にIDを入力する必要があります。
ADJ編を参照して，「USB SERIAL No. INPUT」を行ってください。
1-3. 自己診断機能
1-3-2. 自己診断表示
本機の動作に不具合が生じたとき，L C D 画面のカウンタ表
示部分がアルファベットと数字の4 桁表示になり，3 . 2 H z で
点滅します。この5 文字の表示によって対応者分類および不
具合の生じたブロックの分類，不具合の詳細コードを示し
ます。
1-3-1. 自己診断機能について
本機の動作に不具合が生じたとき，自己診断機能が働き，
L C D 画面に，どう処置したらよいか判断できる表示を行い
ます。自己診断機能については取扱説明書にも掲載されて
います。
LCD画面
C:31:11
3.2Hz点滅
C
対応者分類
C ：お客さま自身で対応
H ：販売店で対応
E ：サービスエンジニア
で対応
31
ブロック分類
11
詳細コード
対応方法の違いにより分類 「1-3 -3 . 自己診断コード表」
例 31 ･･･テープを入れ直す を参照
32 ･･･電源を入れ直す
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-8
ENGLISH
JAPANESE
1-3-3. 自己診断コード表
自己診断コード
対 ブロック
応
機能
者
詳細
コード
C
0
4
0
0
標準以外のバッテリを使用している インフォリチウムバッテリを使用する。
C
1
3
0
1
フォーマットしていない“メモリー “メモリーステック デュオ”をフォーマットする。
ステック デュオ”を入れた
“メモリーステック デュオ”が壊 新しい“メモリーステック デュオ”に交換する。
れている
C
1
3
0
2
アクセスエラー
C
3
2
6
0
フォーカスが合いにくい
操作スイッチの電源を入れ直す。
（フォーカスの初期化ができない） 復帰しない場合，レンズブロックのフォーカスMRセンサ
（LD-222基板CN5302 qh，qkピン）を点検する。異常なけ
ればフォーカスモータ駆動回路（LD-222基板IC5404）を
点検する。
E
2
0
0
0
EEPROMが書き換えられている
E
6
1
1
0
ズーム動作の異常（ズームレンズの ズームレバーを操作したときにズーム動作をすれば，レン
初期化ができない）
ズブロックのズームMRセンサ（LD-222基板CN5302 w;，
waピン）を点検する。ズーム動作をしなければズームモー
タ駆動回路（LD-222基板IC5404）を点検する。
E
6
1
1
1
フォーカス，ズーム異常
自己診断コードC：32：60とE：61：10の両方を点検す
る。
E
6
2
0
0
手振れ補正が効きにくい（PITCH
角速度センサ出力張り付き）
PITCH角速度センサ（CM-077基板SE7202）周辺回路を点
検する。
E
6
2
0
1
手振れ補正が効きにくい（YAW 角
速度センサ出力張り付き）
YAW角速度センサ（CM-077基板SE7201）周辺回路を点検
する。
E
6
2
0
2
手振れ補正用ICの異常
「1-4-1. E：62：02（手振れ補正用ICの異常）が出た場
合」を参照。
E
6
2
0
3
手振れ補正用ICとマイクロコント
ローラーとの通信異常
手振れ補正回路（LD-222基板IC5703）を点検。
E
6
2
1
0
シフトレンズ初期化異常
「1-4-2. E：62：10（シフトレンズ初期化異常）が出た場
合」を参照。
E
6
2
1
1
シフトレンズオーバーヒート
（PITCH）
「1-4-3. E：62：11（シフトレンズオーバーヒート
（PITCH））が出た場合」を参照。
E
6
2
1
2
シフトレンズオーバーヒート
（YAW）
「1-4-4. E：62：12（シフトレンズオーバーヒート
（YAW））が出た場合」を参照。
E
6
2
2
0
サーミスタの異常
「1-4-5. E：62：20（サーミスタの異常）が出た場合」を
参照。
E
9
1
0
1
フラッシュの充電異常
フラッシュユニットの点検または交換をする。（注1）
E
9
4
0
0
フラッシュメモリの書込み/消去動
作不良
フラッシュメモリ（VC-493基板IC2201）を点検する。
（注2）
症状／状態
対応／方法
電源を外し，再度入れ直してから操作する。
EEPROMのデータを元の値に戻す
注1： 修理後は，必ず「1-5. フラッシュ異常修理後の処置」を行ってください。
注2： ADJ編（「1-3. DESTINATION DATA WRITE」）を参照してください。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-9
ENGLISH
JAPANESE
1-4. シフトレンズエラーの対処方法
LD-222基板（A面側）
約 330 msec
注意：Lowの区間の長さは場合によって多少異なる
図2. LD-222基板R5792の出力電圧の変化
VC-493基板（A面側）
R5792
R5737
IC5703
R5721
IC1803
図1. LD-222基板測定箇所
R1846
図3. VC-493基板測定箇所
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-10
ENGLISH
JAPANESE
1-4-1. E：62：02
（手振れ補正用ICの異常）が出た場合
順序
1
2
3
作業内容
電源を切る。
LD-222基板IC5703の周辺にあるR5792の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直後の
出力電圧が図2の様に変化することを確認する。
出力電圧が図2の様に変化するときはレンズブロックを交換する
（注）。図2の様に変化しないときはカメラコント
ロール回路
（VC-493基板IC1803）
周辺を点検する。
注：レンズブロックを交換した場合は，ADJ編を参照して必要な調整項目を実施すること。調整後は手振れ補正ONの状態に
して，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-4-2. E：62：10
（シフトレンズ初期化異常）が出た場合
点検方法：
1） シフトレンズチェックの「Check 1」を実行する（注1）。
注1： シフトレンズチェックについては，ADJ編（「3-2. サービスモード」の「7. シフトレンズチェック」）を参照して
ください。
2） 「Check 1」を実行している間に「EEPROM Error」のメッセージが表示された場合は，EEPROM（VC-493基板IC1804）を
点検する。
3） 電源を切り，再び電源を入れる。
4） エラーが発生しないことを確認する。もしエラーが発生する場合はレンズブロックを交換する（注2）。
注2： レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の
状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-4-3. E：62：11
（シフトレンズオーバーヒート（PITCH））
が出た場合
点検方法：
1） シフトレンズチェックの「Check 2」を実行する（注1）。
注1： シフトレンズチェックについては，ADJ編（「3-2. サービスモード」の「7. シフトレンズチェック」）を参照して
ください。
2） 「Check 2」を実行している間にシフトレンズが動いたか確認する。もしシフトレンズが動かない場合はレンズブロック
を交換する（注2）。動く場合は順序3に進む。
3） LD-222基板IC5703の周辺にあるR5721の出力電圧をオシロスコープで測定しながら，「Check 2」を実行したときに出力
電圧が変化することを確認する。
4） 出力電圧が変化しないときはレンズブロックを交換する（注2）。変化するときは順序5に進む。
5） 電源を切る。
6） LD-222基板IC5703の周辺にあるR5792の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直後の出力
電圧が図2の様に変化することを確認する。
7） 出力電圧が図2の様に変化するときはレンズブロックを交換する（注2）。図2の様に変化しないときはカメラコントロー
ル回路（VC-493基板IC1803）周辺を点検する。
注2： レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の
状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-4-4. E：62：12
（シフトレンズオーバーヒート（YAW））
が出た場合
点検方法：
1） シフトレンズチェックの「Check 3」を実行する（注1）。
注1： シフトレンズチェックについては，ADJ編（「3-2. サービスモード」の「7. シフトレンズチェック」）を参照して
ください。
2） 「Check 3」を実行している間にシフトレンズが動いたか確認する。もしシフトレンズが動かない場合はレンズブロック
を交換する（注2）。動く場合は順序3に進む。
3） LD-222基板IC5703の周辺にあるR5737の出力電圧をオシロスコープで測定しながら，「Check 3」を実行したときに出力
電圧が変化することを確認する。
4） 出力電圧が変化しないときはレンズブロックを交換する（注2）。変化するときは順序5に進む。
5） 電源を切る。
6） LD-222基板IC5703の周辺にあるR5792の出力電圧をオシロスコープで測定しながら電源を入れる。電源投入直後の出力
電圧が図2の様に変化することを確認する。
7) 出力電圧が図2の様に変化するときはレンズブロックを交換する（注2）。図2の様に変化しないときはカメラコントロー
ル回路（VC-493基板IC1803）周辺を点検する。
注2： レンズブロックを交換した場合は，A D J 編を参照して必要な調整項目を実施すること。調整後は手振れ補正O N の
状態にして，手持ち動作で手振れ補正が適切に動作していることを確認する。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-11
ENGLISH
JAPANESE
1-4-5. E：62：20（サーミスタの異常）が出た場合
順序
1
2
3
作業内容
電源を入れる。
VC-493基板IC1803の周辺にあるR1846が0 Ωであり，かつ通電していることを確認する。通電していない場合は
R1846を交換する。R1846が0 Ωであり，かつ通電している場合はレンズブロックを交換する
（注）
。
レンズブロックを交換し必要な調整を行った後，エラーが発生しないことを確認する。もしエラーが発生する場
合はカメラコントロール回路
（VC-493基板IC1803）
周辺を点検する。
注：レンズブロックを交換した場合は，ADJ編を参照して必要な調整項目を実施すること。調整後は手振れ補正ONの状態に
して，手持ち動作で手振れ補正が適切に動作していることを確認する。
1-5. フラッシュ異常修理後の処置
本機はフラッシュエラー（自己診断コードE : 9 1 : 0 1 ）が発生した場合，高電圧による異常を防止するために自動的にフラッ
シュ充電および発光禁止の設定になります。
フラッシュエラー発生後はエラーの解除を行う必要があります。エラーは，「全履歴データの初期化」を実行することによ
り解除できます。
注：「全履歴データの初期化」については，ADJ編（「3-2. サービスモード」の「6. 履歴データ」）を参照してください。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-12
ENGLISH
JAPANESE
1-6. MSホルダー交換時の注意
1-6-1. MSホルダー注文時の注意
機種の表示部はレーザー印字方式を採用しております。
この為，交換用のMSホルダーは機種，仕向けにより異なり
ます。類似の表示もありますので，該当するものを選んで
注文してください。
HDR-CX7 (J仕向)
注意： MSホルダー交換後はシリアルナンバーがサービス専
用のシリアルナンバーに変更されます。お客様への
案内と修理データのシリアルナンバー変更を行って
ください。
HDR-CX7E (CH仕向)
HDR-CX7EK (E, HK, AUS, JE仕向)
シリアル
ナンバー
シリアル
ナンバー
シリアルナンバー
部品コード
部 品 名
部品コード
A-1334-454-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7-J1)
HDR-CX7 (US仕向)
部 品 名
部品コード
A-1334-457-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7E-CN2)
HDR-CX7K (E, JE仕向)
部 品 名
A-1334-460-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ(CX7KE-E34)
HDR-CX7EK (AEP仕向)
シリアル
ナンバー
シリアルナンバー
シリアルナンバー
部品コード
部 品 名
部品コード
A-1334-455-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7-U2)
HDR-CX7 (CND仕向)
部 品 名
部品コード
A-1334-458-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7K-E23)
HDR-CX7K (KR仕向)
部 品 名
A-1334-461-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ(CX7KE-CEN)
HDR-CX6EK (AEP, UK仕向)
シリアル
ナンバー
シリアル
ナンバー
シリアルナンバー
部品コード
部 品 名
A-1334-456-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7-CA2)
部品コード
部 品 名
A-1334-459-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ- (CX7K-KR2)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-13
部品コード
部 品 名
A-1334-462-A ｻ-ﾋﾞｽ 用MSﾎﾙﾀﾞ(CX6EK-CEH)
ENGLISH
JAPANESE
1-6-2. 日本向けモデルのMSホルダー交換時の注意
交換前のM S ホルダーに印字されている“製造年（下図の○部の表示）”と同じ表示のラベルを新しいM S ホルダーに貼付け
てください。
例：下図では，“07年製”のラベルを貼る
* ラベルは，サービス用MSホルダーに「投げ込み（ラベル貼り方）」を含めて同梱されています。
* 製造年
* ラベルを貼付けてください
1-6-3. US向けモデルのMSホルダー交換時の注意
交換前のMSホルダーに印字されている“製造年月および製造所（下図の○部の表示）”と同じ表示のラベルを新しいMS
ホルダーに貼付けてください。
例：下図では，“7A”と“SKD”のラベルを貼る
* ラベルは，サービス用MSホルダーに「投げ込み（ラベル貼り方）」を含めて同梱されています。
* US向けの新しいMSホルダーは，ラベルを貼る領域を広くするため，印字のレイアウトが変わっています。
交換前のMSホルダー
新しいMSホルダー
* 製造所
製造所
製造年月
* 製造年月
* ラベルを貼付けてください
1-6-4. 韓国向けモデルのMSホルダー交換時の注意
交換前のM S ホルダーに印字されている“製造年月（下図の○部の表示）”と同じ表示のラベルを新しいM S ホルダーに貼付
けてください。
例：下図では，“2007.5”のラベルを貼る
* ラベルは，サービス用MSホルダーに「投げ込み（ラベル貼り方）」を含めて同梱されています。
* 製造年月
* ラベルを貼付けてください
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1-14E
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is possible that a wire is snapped.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• When installing a connector, don’t press down at wire of connector.
It is possible that a wire is snapped.
DISCHARGING OF THE ST-165 BOARD’S CHARGING CAPACITOR (C5206)
The charging capacitor (C5206) of the ST-165 board is charged
up to the maximum 330 V potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by
the charged voltage which is kept without discharging when the
main power of the unit is simply turned off. Therefore, the
remaining voltage must be discharged as described below.
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the short jig
about 10 seconds.
ST-165 Board
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 kΩ /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
1 kΩ/1 W
R:1 kΩ/1 W
(Part code: 1-215-869-11)
Wrap insulating tape.
C5206
NOTE FOR DISCONNECTING THE HARNESS (COAXIAL CABLE)
When disconnecting the harness (Coaxial Cable), do not pull the
harness part but pull off the connector body with tweezers etc.
Harness
(Coaxial Cable)
Tweezers etc.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-1
2-1. IDENTIFYING PARTS
Top Cabinet Section
Cabinet L Section
⋅ PH-002 Board
BT Panel Section
⋅ CR-084 Board
Lens Section
⋅ LD-222 Board
⋅ CM-077 Board
VC-493 Board
Cabinet R Section
Flash Unit Section
⋅ CK-178 Board
⋅ ST-165 Board
Front Panel Section
MS-363 Board Section
⋅ MS-363 Board
LCD Panel Section
⋅ PD-324 Board
- DISASSEMBLY FLOW 2-2-1. OVERALL SECTION
⋅ LCD Panel Section
⋅ Front Panel Section
2-2-4. MAIN BODY SECTION
⋅ Top Cabinet Section
⋅ MS-363 Board Section
⋅ Cabinet L Section
2-2-5. LENS/BT SECTION
⋅ Lens Section
⋅ BT Panel Section
⋅ VC-493 Board
⋅ Flash Unit Section
2-2-2. LCD PANEL SECTION
⋅ LCD Panel Section
⋅ Cabinet R Section
2-2-3. CABINET R SECTION
⋅ Hinge Block
⋅ CK-178 Board
⋅ Loud Speaker
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-2
HELP
2-2. DISASSEMBLY
EXPLODED VIEW
HARDWARE LIST
2-2-1. OVERALL SECTION
Follow the disassembly in the numerical order given.
1 LCD Panel Section (1-1 to 1-14)
2 Front Panel Section (2-1 to 2-8)
Main Body Section
(See Page 2-6)
1-8 (#2)
2 Front Panel Section
2-8
2-2 (Claw)
1-7
HELP
2-5 (#2)
1-10
(#2)
1-13
2-6
1 LCD Panel
Section
1-14
(See Page 2-4)
2-3
2-4 (#2)
1-1
(Open)
2-7
1-4 (Claw)
1-12
(#2)
1-11 (#2)
1-2
(#1)
1-6
(#2)
1-9 (#2)
1-5
1-3
2-1 (#2)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-3
2-2-2. LCD PANEL SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 LCD Panel Section (1-1 to 1-6)
1-3
(#2)
1-2
(#2)
Cabinet R Section
(See Page 2-5)
1-6
1-4
(Claw)
1-5
1-1
(#2)
PD
-32
4
1 LCD Panel Section
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-4
2-2-3. CABINET R SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Hinge Block (1-1 to 1-3)
2 CK-178 Board (2-1 to 2-6)
3 Loud Speaker (3-1 to 3-2)
2-1 (#3)
2-2
2-4
HELP
2 CK-178 Board
Note: On installation of the CK-178 board,
adjust the position of the Night Shot
switch and the Night Shot nob.
3 Loud
Speaker
8
-17
CK
2-3
3-1 (#3)
3-2
2-6 (#3)
2-5
HELP
1-2
1-1
HELP
HELP
1-3
(#2)
1 Hinge Block
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-5
2-2-4. MAIN BODY SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 Top Cabinet Section (1-1 to 1-4)
2 MS-363 Board Section (2-1 to 2-3)
3 Cabinet L Section (3-1 to 3-4)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between the two points with the short jig
about 10 seconds.
ST-165 Board
R:1 kΩ/1 W
(Part code: 1-215-869-11)
1 Top Cabinet Section
1-1 (#2)
1-4
3-3 (#2)
LENS/BT Section
(See Page 2-7)
3-4 (Claw)
1-3
1-2 (#2)
3-1 (#2)
3 Cabinet L
Section
2 MS-363
Board
Section
2-1 (#2)
S
M 3
36
2-2
3-2 (#2)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-6
2-3
2-2-5. LENS/BT SECTION
EXPLODED VIEW
Follow the disassembly in the numerical order given.
HARDWARE LIST
1 VC-493 Board Block (1-1 to 1-12)
2 BT Panel Section (2-1 to 2-2)
3 ST-165 Board Block (3-1 to 3-6)
3 ST-165 Board Block
2-1 (#3)
1-8
2 BT Panel Section
3-5
(#3)
3-6
(Claw)
ST
5
16
3-1
1-12
2-2 (#3)
1-11
(#3)
1-4
1-6
(Note)
3-4
3-2
(#2)
3-3
(Claw)
VC
3
9
4
1-10 1-2 (Claw)
(#3)
1-5
1-7
1 VC-493 Board Block
1-9
(#3)
1-3
1-1
(#3)
Note: Refer to page 2-1 “Note
for disconnecting the
harness (coaxial cable)”.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
2-7E
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
THE METHOD OF ATTACHMENT OF FP-737 FLEXIBLE BOARD
1 Fold dotted line parts of the FP-737 flexible board as shown in figure.
Valley fold
Mountain fold
Adhesive tape
Valley
fold
Valley
fold
Adhesive
tape
Mountain
fold
Mountain fold
Unite
corners.
Stick it together in the adhesive tape
while bending the FP-737 flexible board.
2 Pass FP-737 flexible board through the flexible clamp
as shown in figure.
3 Install the flexible clamp in the hinge assy
as shown in figure.
Stopper of FP-737 flexible board
Flexible clamp
Concave side
of hinge
Flexible clamp
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
HELP
4 Roll the FP-737 flexible board 1.5 times in the hinge assy and put it on the hinge assy
with the adhesive tape as shown in figure.
Boss
1.5 times
Adhesive Tape
5 Fold dotted line parts of the FP-744 flexible board as shown in figure.
Valley fold
Switch
FP-744 flexible board
6 Install the FP-744 flexible board in the hinge cover (rear) as shown in figure.
FP-744 flexible board
Hinge cover (rear)
Switch
7 Install the hinge cover (rear) in the hinge assy as shown in figure.
Hinge cover (rear)
Switch
FP-737 flexible board
Plate of hinge
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
HELP
Cabinet R section
CK-178 board
Tape
Loud speaker
Harness arrangement
Front panel section
Barrier sheet
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
HELP
3. BLOCK DIAGRAMS
Link
OVERALL BLOCK DIAGRAM (1/5)
OVERALL BLOCK DIAGRAM (5/5)
OVERALL BLOCK DIAGRAM (2/5)
POWER BLOCK DIAGRAM (1/3)
OVERALL BLOCK DIAGRAM (3/5)
POWER BLOCK DIAGRAM (2/3)
OVERALL BLOCK DIAGRAM (4/5)
POWER BLOCK DIAGRAM (3/3)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3. BLOCK DIAGRAMS
3-1. OVERALL BLOCK DIAGRAM (1/5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
ND FILTER
DRIVE
CHCK
YAW_IN±
YAW_HALLBIAS±
1-4
CN5301
SHUTTER_A,XA,SHUTTER_B,XB
Q5301
LENS_COVER_LED_ON
LED
9
DRIVE
LENS_COVER_OPEN
8
LENS
BARRIER
UNIT
32
14
8
9
37
29
26
20
17
20
26
38
XIC_5404_RST
EN1, DIRA1, DIRB1
A3
30
16
IC5801
7
3
ENO,
DIRA0,
DIRB0
M4, N1, N2, N4, P1,
P2, V2, V4, W1, W2,
W4, Y1, Y2, AA2
NF_EN, NF_SW
R22
P22
THERM
PITCH_AD
YAW_AD
F2
F4
AC6
B8
VST_C_RESET
XSYS_RST
XRST_IC_5703_CPU
IC_2701_SYSCLK
IC1803
CAMERA CONTROL
(4/18)
C20, D20, A17 B19, D19, D18, D16, C16, A15,
A19, C18, C19, B15, B16, B17,
D17, C17
C15, D15
E2, E1,
D3 – D1,
C3 – C1
H2 – H4
A3
A10
AA6
STL_ADDR0 – STL_ADDR11, STL_BS0, STL_BS1
STL_CLK
STL_XCS0
T4
AB4
AC11
256M SDRAM
(8/18)
AC7
F23
H22
STROBE_ON
EXT_STROBE_ON
2
OVERALL (4/5)
(PAGE 3-4)
3
OVERALL (5/5)
(PAGE 3-5)
HI_SO, HI_SI, XHI_SCK
HI_SO, HI_SI, XHI_SCK
XCS_IC_1803
SYS_V
A11-A14, B11-B14,
C11-C14, D11-D14
J1 J8
XSYS_RST
XSYS_RST
A8
C7
IC1901
L21
AA3
AC5
D24A00_CAM - D31A07_CAM, DXXA08_CAM - DXXA13_CAM
STL_DATA/CCD_IN0 – STL_DATA/CCD_IN13,
0-15
STL_DATA14 – STL_DATA31
XCS_IC_1803
SYS_V
G17
D25
F23
F1
OVERALL (2/5)
(PAGE 3-2)
C1
39
43
EXT_CAM_VD
TG_FLD
XCS_IC_1702_BUS
IC_1702_BUS_CLK
U1
0-31
LENS_TEMP_AD
1
LENS BARRIER
DRIVE(3/4)
EXT_CAM_VD
B14
AB7, Y7, AB6
18
Y11, AB11, AB10
23,25 10,12,22
28
D13
J1
K1
N22, N20
15
D7
A7
C22
YAW_AD
VST_C_RESET
19,21,27
36
XCS_IC_5404
PITCH_AD
A4, B4, B5
OPTICAL IMAGE
STABILIZATION
DRIVE
(2/4)
10
31
PNDCK(13.5M)
EXT_CAM_VD
CAM_SO, CAM_SI, CAM_SCK
EN1, DIRA1, DIRB1
L_EN0,L_DIRA0,L_DIRB0
LENS_COVER_LED_ON
LENS_COVER_OPEN
AB16
B5
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-1
D1
EEP_SI, EEP_SO, EEP_SCK
XCS_EEP
2, 5, 6
YAW_HALL±
IC5703
34
24
AB14, AC14, AB13
YAW_OUT±
XSYS_RST
D12,A13,A14
YAW±
PITCH_HALLBIAS±
C9
G5
J5
D5
A7
A6
12
22
44,42,40
PITCH_IN±
PITCH_HALL±
F2,F3
D6,E6
PITCH_OUT±
31
G6, J8 J9, J7 B10, D10 J3, J2 H2, J4 B1, D1
M
PITCH±
13
19,25,27
L8, M8
NF MOTOR
DRIVE
A5
32, 38 33, 39 40-43
THERM
CAM_VD_HS
P20
23
36, 37 34, 35 47-44
OIS TEMP
SENSOR
ND_NOISE
H1,
G4 – G1,
F3 – F1
Y13, AA13-AA16,
AB12-AB16,
AC14-AC17
J10, J9, K10, K9
F3 – F5, G3 – G5,
H3, H4, J2 – J4,
K2 – K4
U22, U23, V21-V23,
W21-W23, Y21-Y23,
AA21-AA23
G23, J22, M22, K23
H21
X1701
89.010989MHz: NTSC
74.250000MHz: PAL
16
21,23 24,34,36
K6, F1
ZOOM MOTOR
DRIVE
L6, L7
TEMP_OUT
29-26
LENS TEMP
SENSOR
H
CN1005
1
PNDCK
6,4,2
IC5403
ZOOM MOTOR 2
NOISE FILTER
(1/4)
33
B5,B6
C5,C6
Z_MR_A,
Z_MR_B
NF_DRIVE±
M
IR_NOISE
J12
H11
FOCUS
MOTOR
DRIVE
OPTICAL IMAGE STABILIZER
YAW
MOTOR
30
CLOCK
GENERATOR
(3/18)
K12
L12
IC5402
M
H
CN5303
A10
D10
NF MOTOR
PITCH
MOTOR
AHS_SO, AHS_SCK, AHS_XCS0
CPU
(5/18), (6/18)
G10-G14,
H10-H14, J10,
J11, J15, K10
C9
A4
IRIS
DRIVE
K9, L9, M9, J9
ZOOM MR
SENSOR
ZOOM_A,
ZOOM_B,
ZOOM_XA,
ZOOM_XB
7, 1
M
F_MR_A,
F_MR_B
51-48
ZOOM MOTOR
FOCUS±
20, 21
FOCUS MR
SENSOR
AD3_0 – AD3_13
IC1701
CAM_SO, CAM_SI, CAM_SCK
FOCUS MOTOR
M
IC1301
CDS,
A/D CONVERTER
(2/18)
AD1_0 – AD1_13
J11, K11, H12
C10, B11 A11, A9 K2, L2
B1, C4 F3, E3
ND_HALL±
12, 10 11, 9 14, 8
ND_BIAS±
H
IC2101 (1/4)
AHS_TGVD, AHS_TGHD
ND_DRIVE±
16, 18 24, 25
M
F6, G6 H5
K17, H17, J17
ND FILTER
METER
F7, E6, E7
A20
B20
0-31
C5, B6 C6, A5 H1, J1
7, 1
2, 4
I_HALL±
K5 D6 D7
5
E12, E10
H
I_BIAS±
32
FP-742
FLEXIBLE
BOARD
(1/4)
3, 5
M
I_DRIVE±
K21
A5, A6, A8, A16-A21,
A11-A15, B12, B4, B6-B9, B17-B22,
B13, B15, C12, C13, C4-C9, C17, C18, C20,
D6, D7, D17
C15, D12, D13, D15
VST_C_RESET
IC5404
CN5302
A10, A9, B10, B9
CLPOB
EXT_CAM_CLK
EXT_CAM_VD
CAMERA
SIGNAL
PROCESSOR
(3/18)
H23, K22, J21 N21-N23, P21-P23, Y17, AA17-AA20,
R21-R23, T21-T23, AB17-AB21,
U20, U21
AC18-AC21
YAW_AD
LD-222 BOARD
IRIS
METER
ADC_SO, ADC_SCK, XCS_ADC0
VIN_HD, VIN_VD, VIN_FLD
R1
IC1702
L22, J23
9
ADC_TGVD, ADC_TGHD
TGVD, TGHD
34
33
VIN_C0 – VIN_C7
G22, E23, F21
PITCH_AD
7
8
VIN_Y0 – VIN_Y7
F6, G6 H5
Y8, Y10, Y12,
AA7-AA9, AA11,
AA12, AB8-AB10,
AC8, AC9, AC13
YAW
SENSOR
AD2_0 – AD2_13
A3 – A5, B3 – B5, F3 – F5, G3 – G5,
C3 – C5, D3 – D5, H3, H4, J2 – J4,
E4, E5
K2 – K4
SE7201
F7, E6, E7
AD0_0 – AD0_13
CHCK
XSYS_RST
CAM_VD_HS
12-9
23-20 19-16
37,36
CHCK3/6M
XSYS_RST
AHS_SO, AHS_SCK, AHS_XCS0
6
20
IC7201
10 PITCH/YAW 16
SENSOR
AMP
17
(2/3)
K5 D6 D7
DRVOUT1, DCOUT1,
DRVOUT5, DCOUT5
SE7202
PITCH
SENSOR
CDS,
A/D CONVERTER
(1/18)
A10, A9, B10, B9 J10, J9, K10, K9
AHS_SO, AHS_SCK, XCS_AHS
25
30
DRVOUT2, DCOUT2,
DRVOUT6, DCOUT6
CAM_VD_HS
7, 6, 8
5, 4
TGVD, TGHD
16
11
IC1201
40-38
2
10
4-1
37-40
CHCK3/6M
XSYS_RST
18-21 22-25 29-32
DRVOUT1, DCOUT1,
DRVOUT5, DCOUT5
DRVOUT3, DCOUT3,
DRVOUT7, DCOUT7
4, 5
DRVOUT2, DCOUT2,
DRVOUT6, DCOUT6
1-3
DRVOUT3, DCOUT3,
DRVOUT7, DCOUT7
40, 39, 42, 41, 44, 43,
33, 34 31, 32 29, 30
IC6701
6M CMOS
IMAGER
(1/3)
CN1202
DRVOUT4, DCOUT4,
DRVOUT8, DCOUT8
CN6601
DRVOUT4, DCOUT4,
DRVOUT8, DCOUT8
46, 45,
27, 28
IRIS
(SHUTTER)
A3 – A5, B3 – B5,
C3 – C5, D3 – D5,
E4, E5
VC-493 BOARD (1/5)
CM-077 BOARD
LENS BLOCK
1
IC1804
128k EEPROM
(4/18)
X1802
20MHz
A : VIDEO SIGNAL
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
35 35
31 31
33 33
33 33
TP_SEL_1
AA9
AA11
Y10
IC2701
35 35
31 31
LNDAYDT
Q2908, Q2910, Q2911
LNDAPBDT
BUFFER
LNDAPRDT
AUDIO/VIDEO
CODEC
(10/18)
IC_2901_Y_OUT
IC_2901_C/PB_OUT
IC_2901_PR_OUT
IC_2901_Y_OUT
IC_2901_C/PB_OUT
DR_VINCK
DR_SCK54
F35
E35
XCS_IC_2901
L18, M19, M18
U27
BB_SI, BB_SO, XBB_SCK
XBB_RST
G20
2, 6 – 8, 11 – 14, 19 – 22 1, 23, 24
5, 24, 6, 7,
28, 8, 9, 10,
11, 12, 14, 16
48, 1
42, 45, 44
Q6101, Q6102
TOUCH
PANEL
I/F
TP_R
TP_BOT
30 30
BL_CONT
14
BACKLIGHT
DRIVE
1
4
BL_CONT
14
D6106 - D6108
(BACKLIGHT)
5
OVERALL (3/5)
(PAGE 3-3)
FP-745 FLEXIBLE BOARD
6
HMCK
HM74CK
T20
P21
E1
G1
ADA_SIA0
7
OVERALL (3/5)
(PAGE 3-3)
HDMI
SIGNAL
PROCESSOR
(12/18)
K8
AD98_HSYNC,AD98_VSYNC
AD98_IDCK
F12
H12
H3
C11
ADA_FCK
ADA_BCK
ADA_LRCK
D10
E10
E11
D12
E21
F20
AD98_DE
J12
IC3101
BB_SI,BB_SO,XBB_SCK
H2
XCS_IC_3101
XHDMI_RST
AD98_SD0, AD98_SD1
G11
F10
2,3,5,6,8,9
TMDS_DATA0_± – TMDS_DATA2_±
IC3202
HDMI
TRANSMITTER
(13/18)
TMDS_CLOCK_±
11, 12
HM_HD, HM_VD
J1, K1, K2, K12,
L1 – L11, M3 – M11
HM_B0 – HM_B7
AD98_D0 – AD98_D23
J9, K10
C7, C6 A5 – A8, A2 – A4, A9, A10,
B5 – B8 B2 – B4, B9 – B12,
C1, D1 C12, D12
U21, V20,
V21, W20,
W21, Y20, Y16 – Y19, Y12 – Y15,
T21, U20 Y21, AA20 AA16 – AA19 AA12 – AA15
HM_R0 – HM_R7
G9, G10
B15
HM_Y0 – HM_Y7
CN1001
AD98_MCLK
AD98_SCK
HDMI
OUT
G9
F8
Q3201
C2
F4
XHDMI_RST
B2
J21
I2C_SDA, I2C_SCK
LEVEL
SHIFT
SDA, SCL
HPD
19
Q3202
D8
LEVEL
SHIFT
2
XHDMI_JACK_IN
XCS_IC_3101
XHDMI_RST
AM30, AN33,
AN30, AM32
AM31
AR32
AN9
MSX_BIO0 – MSX_BIO3
XMS_IN
MSX_BIO0 – MSX_BIO3
MSX_BS
MSX_BS
MSX_CLK
CN7401
8
3
MSX_CLK 11
MS_O/C
1
MS_O/C
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-2
MS_INSERT
MS_DIO
MS_DATA1 – 3
MS_BS
MS_SCLK
8
3
11
1
XMS_IN
MSDATA0 – MSDATA3
MSBS
MS_SCLK
S7401
(MS COVER OPEN/CLOSE)
6
4, 3, 5, 7
XHDMI_JACK_IN
H28
8
OVERALL (5/5)
(PAGE 3-5)
4, 5, 7, 9
I2C_SDA, I2C_SCK
FP-735
MS-363 BOARD
FLEXIBLE BOARD
CN1002
4, 5, 7, 9
AR13, AR12
T26
A28
TOUCH
PANEL
BL_L
16, 15
DR_GSPILOT
G35
5
D3, D2, F2
G32, G34,
F32, F34
DR_GSDATA0 – DR_GSDATA3
B16, A16, B17, A17, D18, B18,
A15, A14 A18, B19, A20, B21
DR_GHPILOT
D14, B14,
D13, A13
DR_GHDATA0 – DR_GHDATA3
5
CN6102
TP_TOP
5
TP_L
2
CN3201
D1002
(NIGHTSHOT)
DR_VDATA0 – DR_VDATA7
H35
RGT, PSIG, HCK1, HCK2,
REF, HST, PCG, XSTBY,
DWN, EN, VCK, VST
2.7 inch
WIDE
COLOR
LCD
UNIT
OVERALL (5/5)
(PAGE 3-5)
J1, G2, H1
E32, G33, D35, E34, D33, D34,
E33, F33 D32, C34, B33, C33
D30
BL_CONT
BL_CONT
M1
C3
LED
DRIVE
4
6
EXTDA, BL_ON
30 30
BB_SO, XBB_SCK
Q1001
IR_LED_ON
COM, CS
Q6107, Q6110,
Q6112, Q6113
M4
PCI_CLK
PCI_CLKRUN
TP_SEL_1
4
6
11,12,14,15,17,18
PCI_XRESET
AP19
AR16
AR17
AM19
TP_X
TP_Y
4
BB_SO, XBB_SCK
U2, R2, V4, W3, U4, W2,
L4, G3 V3, W1, V2, T4,
T3, U3, R4, T2,
R3, P3, R1, P4,
K4, L2, J4, K3,
J3, K2, H3, H4,
G4, G2, F1, F3,
F2, D2, F4, E3
AM22 – AM29,
AN22 – AN29,
AM16, AN16, AP22 – AP29,
AM17, AP15 AR22 – AR29
PCI_XBE0 – PCI_XBE3
43
20
21
22
26
OVERALL (3/5)
(PAGE 3-3)
B3
PCI_AD0 – PCI_AD31
LCD DRIVE
8,9
4
IC6102
5,6
X2101
12MHz
DOWN
CONVERTER
(11/18)
AC15
AA13
IC2102
BUFFER
(5/18)
9
A2 – A7
3
34
33
32
9
A8, A9
H32
H33
XCS_LCD
C9, B10
CPU
(5/18)
(6/18)
TP_X
TP_Y
IC2901
AA14
IC_2701_MCK
IC_2701_LRCK
21 21
22
23
24
CN6105
R
4
G
5
B
3
31, 18
AC11
A15
IC_2701_ADATA
21 21
22
23
24
E1 – E3, F1 – F3,
G1 – G3, H2,
H4 – H7, J2 – J4,
J7, J8, K1 – K4, K7
IC2101
(2/4)
XCS_LCD
BB_SI, BB_SO, XBB_SCK
J9, K9
IC_2701_VCLK
IC_2701_SYSCLK
BB_SI, BB_SO, XBB_SCK
PANEL_HD, PANEL_VD
LCD901
CN6101
(1/2)
F9, G8
IC_2701_DATA0 – IC_2701_DATA7
J33
PANEL_HD, PANEL_VD
AA12, Y12, Y11,
AA11, AB11,
AB10, AA10, Y10
M32, M33, L32,
L33, L34, K32,
K33, J32
OVERALL (1/5)
(PAGE 3-1)
K35
L35
BUFFER
K1, K2
1
IC_2701_SYSCLK
PNDARDT
PNDAGDT
PNDABDT
6, 10
6, 10
AA2
AA4
AA5
17,19,23
17,19,23
TOUCH PANEL
SELECT SWITCH
6, 10
6, 10
TP_SEL2
A17, AC16
B28
CN6003
(1/2)
CN1006
CN6002 CN1006
CN6002(1/3)
(1/3)
(1/3) (1/3)
PANEL_R
PANEL_R
38 38
38 38
PANEL_G
PANEL_G
36 36
36 36
PANEL_B
PANEL_B
34 34
34 34
Q2902 – Q2904
17,19,23
17,19,23
Q1009
19,15
TP_X
AM35
TP_Y
AN34
TP_SEL1
B29
PD-324 BOARD (1/2)
FP-737
FLEXIBLE
BOARD
(1/2)
8,10,11
XCS_LCD
C3, D3
T27
CK-178 BOARD (1/3)
FP-736
FLEXIBLE
BOARD
(1/3)
19,15
VC-493 BOARD (2/5)
8,10,11
3-2. OVERALL BLOCK DIAGRAM (2/5)
CN7402
MEMORY
STICK
DUO
2
8
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
3-3. OVERALL BLOCK DIAGRAM (3/5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-743
FLEXIBLE
BOARD (1/2)
40
44
48
68,70
OVERALL (2/5)
(PAGE 3-2)
BB_SO, XBB_SCK
T25
A23
XCS_DDRA
XCS_DDRA
XD_CRADLE_DET
PB_IN
PR_IN
XD_CRADLE_DET
BB_SO, XBB_SCK
XCS_DDRA
XD_CRADLE_DET
66
65
2
4
6
67
66
20
44
CN7303
(1/2)
Y
9
Pb
13
Pr
17
35
33
31
IC3001
COMPONENT
OUT AMP,
D-TERMINAL
DRIVER
(1/2)
CTRL1 – CTRL3
DET
40
21,23,25
4
Y_IN
43 – 41
IC_2901_Y_OUT
IC_2901_C/PB_OUT
IC_2901_PR_OUT
CR-084 BOARD (1/2)
CN7301
(1/2)
IC_2901_Y_OUT
41
IC_2901_C/PB_OUT
45
IC_2901_PR_OUT
49
23, 22
CN1010
(1/2)
69,71
VC-493 BOARD (3/5)
19
G25
AJ34
USB_D±
USB_D±
Q1008
XVBUS_DET
USB_VCC
USB
DETECT
USB_VBUS
79
USB_DET/VBUS
S_Y_I/O
80
S_C_I/O
VIDEO_I/O
JACK_AD
AUDIO_L_I/O
AUDIO_R_I/O
U26
IC2101
(3/4)
CPU
(5/18)
(6/18)
R35
XCS_IC_3301
XCS_IC_3301
SYS_SOUND
SYS_SOUND
OVERALL (2/5)
(PAGE 3-2)
BB_SO, XBB_SCK
ADA_FCK
ADA_BCK
ADA_LRCK
ADA_SIA0
N28
P29
ADA_SOA0
ADA_SOA0
ADA_SOA1
ADA_SOA1
9
PH-002
BOARD (1/3)
CN901(1/2)
MIC_FL
3
3
MIC_FR
2
2
6
MIC_RL
6
MIC_RR
5
5
FRONT
MIC901
MICROPHONE
UNIT
5
L
3
R
1
CN7603
(1/2)
MicFL
CN7601
(1/3)
31
MicFR
29
MicRL
28
SHOE_MIC_FL
SHOE_MIC_FR
SHOE_MIC_RL
30
Q7603
BUFFER
INT_MIC_L
Q7602
BUFFER
INT_MIC_R
Q7601
BUFFER
33
9
11
12
37
35
10
INT_MIC_F
INT_MIC_L
INT_MIC_R
N13
P13
XSYS_RST
7
3
5
CN7302
S_Y_I/O
53
57
61
S_C_I/O
VIDEO_I/O
S_C_I/O
VIDEO_I/O
SHOE_MIC_FL
SHOE_MIC_FR
SHOE_MIC_RL
SHOE_MIC_RR
INT_MIC_F
INT_MIC_L
INT_MIC_R
20
22
31
S_Y_I/O
1
3
5
S_C_I/O
VIDEO_I/O
10
5
9
CN001
A/V OUT
F2
G1
C14
C13
49
53
LANC_SIG
50
54
AUDIO_R_I/O
JACK_AD
59
10
AUDIO_L_I/O
AUDIO_L_I/O
MULTI_JACK_IN
60
LANC_SIG
61
AUDIO_R_I/O
LANC_SIG
62
K14
CN1007
(1/3)
SHOE_MIC_RR
MicRR
CN7602
INT_MIC_F
FP-739
FLEXIBLE
BOARD
(1/3)
N14
M14
M13
P12
OVERALL (5/5)
(PAGE 3-5)
OVERALL (5/5)
(PAGE 3-5)
FP-740
FLEXIBLE
BOARD (1/2)
52
56
60
A11
SP ±
CN1006
(2/3)
SP ±
FP-736
FLEXIBLE
BOARD (2/3)
CK-178 BOARD
(2/3)
CN6002 CN1006
(2/3)
(2/3)
SP ±
CN6002
(2/3)
CN6004
SP(+), SP(-)
B10
A8
B7
A10
B14
B13
A : VIDEO SIGNAL
A : AUDIO SIGNAL
A : VIDEO/AUDIO SIGNAL
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-3
1, 2
5
K1
M2
L1
1,3
1,3
ADA_SIA0
OVERALL (2/5)
(PAGE 3-2)
S_Y_I/O
N4
N3
1,3
1,3
ADA_SIA0
7
IC_2901_Y_OUT
IC_2901_C/PB_OUT
12
8
FP-738 FLEXIBLE
BOARD
VIDEO OUT,
AUDIO IN/OUT
(14/18)
ADA_FCK
ADA_BCK
ADA_LRCK
16
A4
B1, C2
ADA_FCK
ADA_BCK
ADA_LRCK
30
K13, J13
R29
HOT SHOE
LANC_SIG
J14
IC3301
M29
M28
N29
34,36
USB_D±
75,77
USB_D±
74,76
W35,V35
CRADLE
(1/2)
SP901
SPEAKER
14
12
9
10
AUDIO_L
AUDIO_R
JACK_AD
LANC_SIG
1
6
7
2
3-4. OVERALL BLOCK DIAGRAM (4/5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-493 BOARD (4/5)
ID1, ID2
HI_XRESET
CN1007
(2/3)
EXT_STROBE_ON
27
LANC_SIG
26
HOTSHOE_ID1,HOTSHOE_ID2
CN7601
(2/3)
STROBE
13
14
LANC
ID1, ID2
LANC_SIG
XBATT_VIEW
FP-734 FLEXIBLE BOARD
IC6503
REMOTE 4
COMMANDER
RECEIVER
3
D6502
(CAMERA RECORDING)
CN1009
SIRCS_SIG
F_TALLY_LED
6
SIRCS_SIG
XTALLY_LED
Y3
AM5
CPU
(5/18)
(6/18)
CN6001
PD-324
BOARD (2/2)
CN6101
(2/2)
KEY_AD0
18
1
S6007
PANEL
OPEN/CLOSE
FP-737
FLEXIBLE
BOARD (2/2)
KEY_AD0
CN1006
(3/3)
CN6002
(3/3)
PANEL_NOR/REV
CN6002
(3/3)
13 13
15 15
15 15
S001
START/STOP
W S003
PANEL_OPEN/CLOSE
PANEL_NOR/REV
PANEL_O/C
H15
CN6003
(2/2)
8 8
2ND_S/S_SW
2ND_ZOOM(W)
CN6103
1
4
8 8
KEY_AD0
KEY_AD0
KEY_AD3
KEY_AD3
9 9
AH35
AH33
OFF
AF16
S002
KEY_AD2
WD_DIS
WD_DIS
XHOT_STBY
XHOT_STBY
FR_SI, FR_SO, XFR_SCK, XCS_EX
XEX_RST
XEX_RST
EMC_DATA[0] –
EMC_DATA[31]
EMC_DATA[0] –
EMC_DATA[31]
(9/18)
EMC_ADDR[0] –
EMC_ADDR[12],
EMC_ADDR[14],
EMC_ADDR[15]
SDRAM
EMC_ADDR[0] –
EMC_ADDR[15]
K11
EMC_DATA[0] –
EMC_DATA[15]
EMC_ADDR[0] –
EMC_ADDR[15]
One NAND
T4
P11
E8
EMC_XRESET_OUT
12
2
(ZOOM)
T
11
OVERALL (5/5)
(PAGE 3-5)
XPHOTO_LED
EMC_CLK1_OUT
Y25
EMC_CLK1_IN
Y26
S6004
FILM ROLL
INDEX
S6009
ON
NIGHTSHOT
KEY_AD1
G24
S6003
BACK LIGHT
HOME_SW
G2
START/STOP
EMC_CLK0_OUT
W25
EMC_CLK0_IN
W26
9 9
S004
HOME
CN1006
(3/3)
PANEL_NOR/REV
13 13
S6010
CONTROL SWITCH BLOCK
(SB25970)
STABLE_RUN
ZOOM_VR_AD
IC2201
S6011
EASY
18
STABLE_RUN
AD18, AD19, AE18 – AE20,
AF18 – AF20, AF26,
AG18 – AG21, AG25, AG26,
AH18 – AH26, AJ19 – AJ26
S001
(PANEL REVERSE)
PANEL_NOR/REV
FP-736
FLEXIBLE
BOARD
(3/3)
CK-178 BOARD (3/3)
ADAPTOR_DET
STRB_CHARGE
XSTRB_FULL
V2
G23
C23
IC2101
(4/4)
FP-744 FLEXIBLE BOARD
ADAPTOR_DET
AP9
STRB_CHARGE
R28
XSTRB_FULL
L19
ZOOM_VR_AD
AJ33
START/STOP
H26
KEY_AD1
AH34
KEY_AD2
AJ35
XPHOTO_LED
AK3
B22, C22, A22, D22
11
12
EXT_STROBE_ON
T10, T11, U11, U12,
V9 – V12, W10 – W12,
Y8 – Y11, AA9
STROBE
LANC
7,10
11
12
7,10
HOT
SHOE
OVERALL (1/5)
(PAGE 3-1)
STROBE_ON
29,28
CN7603
(2/2)
CN901 (2/2)
FP-739
FLEXIBLE
BOARD
(2/3)
STROBE_ON
AM34, AM33
PH-002 BOARD (2/3)
11,12
FP-740
FLEXIBLE
BOARD
(2/2)
2
XFLASH_RST
2ND_ZOOM(T)
3
S6002
DISP/
BATT INFO
S6001
RESET
D6005
(ACCESS)
4 4
4 4
7 7
7 7
11 11
11 11
XBATT_VIEW
XRESET
MS_ACCESS_LED
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-4
XMS_ACC_LED
H23
OVERALL (5/5)
(PAGE 3-5)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
FP-741 FLEXIBLE
BOARD
VC-493 BOARD (5/5)
CN1008
ADAPTOR_DET
9
ST-165 BOARD
FLASH UNIT
CN5201
CN5202
Adapter Detect
8
ST_UNREG
D5202
2
6
C5206 +
CHARGING
CAPACITOR
1
4
STRB_CHARGE
XSTRB_FULL
STROBE_ON
11
OVERALL (4/5)
(PAGE 3-4)
12
11
10
ZOOM_VR_AD
START/STOP
KEY_AD1
KEY_AD2
ZOOM_VR_AD
START/STOP
KEY_AD1
KEY_AD2
XPHOTO_LED
XPHOTO_LED
XBATT_VIEW
G11
B2
L3
X5101
32.768kHz
F11
SCHARGE_ON
XSCHARGE_FULL
STROBE_ON
XCHARGE_LED
5
6
7
FP-739 FLEXIBLE
BOARD(3/3)
IC5201
FLASH/
CHARGE
CONTROL
16
19
21
18
22
14
26
15
25
21
19
CONTROL SWITCH BLOCK (PS25970)
CN7604
XCAM_LED
XPHOTO_LED
HI CONTROL
(15/18)
J4, L5, K5, H3
ZOOM_VR_AD
START/STOP
13
D5313
CHARGE
8
D5315
MOVIE
XPHOTO_LED
11
D5314
STILL
ZOOM_VR
18
START/STOP
14
ZOOM_VR
START/STOP
XEX_RST
LANC_SIG
KEY_AD1
8
B6
9
OVERALL (3/5)
(PAGE 3-3)
XSYS_RST
XMS_IN
KEY_AD1
15
OVERALL (2/5)
(PAGE 3-2)
4
A8
5
3
OVERALL (1/5)
(PAGE 3-1)
KEY_AD1
(STROBE SW)
KEY_AD1
(PHOTO_FREEZE)
KEY_AD1
(PHOTO_REC)
XSYS_RST
B4
A2
XPOWER_SW
XPOWER_SW
XMODE_SW
23
25
XMODE_SW
17
15
XPOWER_SW
XMODE_SW
2
1
XPOWER_SW
XMODE_SW
IC5104
(15/18)
BL_CONT
HI_EVER_SO,
HI_EVER_SCK,
XCS_DD
M13, L13, K13
OVERALL (2/5)
(PAGE 3-2)
VOUT
DC CONTROL, M2
RESET,
LANC DRIVE
D14
(17/18)
6
LANC_IN
LANC_OUT
XLANC_ON
XLANC_PWR_ON
J3
J2
M3
L3
B10
C10
H2
C1
32
J11
D4_-2.8V
BL_-V
EP_8.5V
LANC_DC
EVER_3.0V
57
D4605
C7
E11
F10
CN1003
BATT_XEXT_CN
14
BATT/XEXT
SHOE_UNREG,
ST_UNREG,
VTR_UNREG,
VTR2_UNREG,
MT_BL_UNREG
A_1.2V, D_1.2V, IC_2701_D_1.2V,
A_1.2V_2, D_1.2V_2
D_1.5V
EP_2.8V, A_2.8V, AU_2.8V, D_2.8V
A_4.6V, AU_4.6V, EP_4.6V
D_1.8V
D_3.3V
D_2.5V
MT_5.0V
CMOS_4.1V
CAM_-1.0V
JACK_AD_CRADLE
1 – 13
IC4705
F2
K2
A7
71
FAST_CHARGE
INIT_CHARGE_ON
Q4601,
Q4603
KEY_AD2
(DVD BURN)
BATT/XEXT
JACK_AD_CRADLE
ACV_UNREG
CN7301
CN7303
(2/2)
(2/2)
DVD BURN
37
72
33
58
BATT/XEXT_CR
MULTI_JACK_IN
ACV_UNREG
FP-731
FLEXIBLE
BOARD
BATT/XEXT
9 – 13
OVERALL (3/5)
(PAGE 3-3)
LANC_SIG
DOUBLE
INSERTION
DETECT
ACV_UNREG
ACV_GND
BATT_UNREG
J001
DC IN
Q4604,
Q4610(1/2)
CN1004
D4601
BATT_UNREG
BATT_SIG
A4
8
BATT_SIG
9 – 14
10
VTR_DD_ON
HI_XRESET
BATT_IN
1–6
N5
N7
P3
N2
D2, D1, G1 B11, J2, K10, L10
K3
CR-084 BOARD
(2/2)
D4702
R2
R1
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-5
C
−
FP-733
FLEXIBLE
BOARD
05
+
BH001
BATTERY
TERMINAL
35
26
1–4
CN1010
(2/2)
KEY_AD2
Q4608,Q4610(2/2)
LANC_SIG
FP-743
FLEXIBLE
BOARD(2/2)
B8
2 – 14
1
3
XFLASH_RST 4
1–6
12
OVERALL (4/5)
(PAGE 3-4)
XE_K
Q5201
FLASH
DRIVE
6
PH-002 BOARD (3/3)
CN7601
(3/3)
XCHARGE_LED
24
XCAM_LED
XCAM_LED
2
1
8
7
4
5–8
BT901
(LITHIUM BATTERY)
TRIGGER
L2
E9
D9
E10
FR_SI, FR_SO, XFR_SCK, XCS_EX
HI_XRESET
16
CN1007
(3/3)
XCHARGE_LED
IC5101
STABLE_RUN
WD_DIS
XHOT_STBY
BATT_LI_3V
S001
LENS ADAPTOR
DETECT
XE_A
5
3
3
Adapter Detect
2
T5201
15 – 18
3-5. OVERALL BLOCK DIAGRAM (5/5)
CRADLE
(2/2)
CAMERA
RV103
(ZOOM)
S5314
START/
STOP
S5311
FLASH
S5313
(PHOTO FREEZE)
S5312
(PHOTO REC)
OFF (CHG)
r
ON
r
MODE
PHOTO
POWER
XENON
LAMP
3-6. POWER BLOCK DIAGRAM (1/3)
J001
DC IN
VC-493 BOARD (1/3)
9-13
FP-731
FLEXIBLE
BOARD
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
F4605
32
33
64
63
DOUBLE
INSERTION
DETECT
BATT_XEXT_CR
BH001
BATTERY
TERMINAL
+
C
8
–
E11 F10
CN1004
BATT_UNREG
P53
P52
FP-733
FLEXIBLE
BOARD
J15 PVDD3a
J14 PVDD3b
LX3a K15
LX3b K14
IN3 J13
E1 PVDD2a
E2 PVDD2b
LX2a D1
LX2b D2
IN2 E3
F4604
FAST_CHARGE
INIT_CHARGE_ON
CN7302
7
1-6
LANC_DC
9-14
4
C7 P71_INT01
A4 SIO2
BATT_SIG
L4719
L4722
D_1.2V
A_1.2V
L4714
EP_2.8V
L4725
L4723
L4720
A_2.8V
AU_2.8V
D_2.8V
L4702
L4713
D_1.5V
L4704
L4724
L4721
L4715
A_4.6V
AU_4.6V
EP_4.6V
LX1a G15
LX1b G14
IN1 H13
Q4707
B+ SWITCH
L4703
LANC_DC
BATT/XEXT
FP-738
FLEXIBLE
BOARD
VTR2_UNREG
1-13
33
Q4608,
Q4610 (2/2)
H15 PVDD1a
H14 PVDD1b
VTR_UNREG
2-14
35
CN1010
(1/2)
ACV_UNREG
L4701
F4603
F4606
D4605
CN001
A/V OUT
ST_UNREG
Q4713 CLAMP
D4601
1-4
CRADLE
ST_UNREG
Q4604,
Q4610 (1/2)
FP-743
FLEXIBLE
BOARD (1/2)
CN7301
(1/2)
CN7303
PVDD10 A3
PVDD12 A4
R11 PVDD4a
P11 PVDD4b
LX4a R12
LX4b P12
IN4 N11
R10 PVDD6a
P10 PVDD6b
LX6a R9
LX6b P9
IN6 N10
Q4708
B+ SWITCH
L4706
IC5101
L4716
L4784
ON
2
1
CN7601
(1/2)
17
15
P22 G2
CN1007
(1/2)
XPOWER_SW
23
XMODE_SW
25
P34_AN04 L7
P31_AN01 L6
B4 P00_INT04
A2 P03_INT07
MODE
D5313
CHARGE
D5314
STILL
CAMERA
D5315
MOVIE
RV103
(ZOOM)
12
13
20
24
CHARGE_LED_VDD
20
XCHARGE_LED
16
G11 P50
9
17
CLAMP_ON
D_1.2V
VTR_UNREG
17
P30_AN00 J5
P32_AN02 K6
P33_AN03 J7
VCC1
VCC2
AVCC
AVR
B11
J2
L10
K10
VOUT
N1
P2
C10
N12
B_UNREG
VRO
CH9_SW1
CH6_SW
A5 PVDD8a
B5 PVDD8b
M2 VOUT
P23 H2
P07_INT11 C1
P70_INT00 A7
P11_SO1 D2
P12_SCK1 D1
P21_PPG01 G1
P61_PPG11 C11
F4602
L2 LANC_DC(5.6V)
A
XLANC_ON
XLANC_PWR_ON
BATT_IN
HI_EVER_SO
HI_EVER_SCK
XCS_DD
K1
K2
M3
L3
SENSEa
SENSEb
XCTL2
WAKE_UP
N2 CS_OUT
M13 DIN
L13 CLK
K13 LD
3
IC4703
DC CONTROL
(17/18)
D4708, D4709
L4705
A10 PVDD5a
B10 PVDD5b
L4783
E4
E3
D2
C1
C2
D4707
L4726
Q4704, Q4705
SWITCHING
L4710
PVDD
VOUT A3
SVDD
S1
IC4702
S2
-2.8V REG
(17/18)
STBY
D4_-2.8V
CAM_-1.0V
MT_5.0V
LX5a A9
LX5b B9
IN5 C8
L4731
CMOS_4.1V
L4732
BL_-V
A13
A14
B13
A11
B8 A8
OUT10-1 C15
+INE10 C14
-INE10 D14
Q4706
SWITCHING
BL_CONT
Q4702, 4703
BACKLIGHT
CONTROL
SD1 N9
IC4705
DC CONTROL,
RESET, LANC DRIVE
(17/18)
D4702
VCH R2
VBATT R1
VOUT3 B2
3-6
IC_2701_D_1.2V
D_1.2V_2
A_1.2V_2
VB B1
VR P4
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
L4712
L4786
L4785
-INE9 C12
+INE9 B12
P3 RST_OUT(RESET)
N5 CTL1
N7 CH8_SELECT
05
D_3.3V
1
DVDD1 A1
DVDD2 A12
PVDD11 A2
OUT9-1
OUT9-2
VS9
CAP_IN
XFL_RST
XSYS_RST
HI_XRESET
VTR_DD_ON
+
–
4
VTR_UNREG
MT_BL_UNREG
1.8/3VCTRL
HI_XRESET
VTR_DD_ON
V_UNREG
AVDD1
AVDD3
DVDD4
DVDD3
L4718
B
LX8a A6
LX8b B6
IN8 C7
P64
P65
RSTX K2
P20_PPG00 F2
P1
R5
L1
P15
D15
D_2.5V
POWER
ON/OFF
L4708
D_2.8V
POWER (2/3)
(PAGE 3-7)
LX7a G1
LX7b G2
IN7 F3
Q4701
BATT_UNREG
EVER_3.0V
LANC_DC
23
Q4709
B+ SWITCH
L4707
F1 PVDD7a
F2 PVDD7b
1.8/3VCTRL
D_2.8V
CN7604
4 VDD VOUT 3
1 CE
MT_BL_UNREG
OFF (CHG)
POWER
FP-739
FLEXIBLE
BOARD
(1/2)
PH-002
BOARD
(1/2)
D_1.8V
IC4704 2.5V REG
(17/18)
HI CONTROL
(15/18)
CONTROL SWITCH BLOCK
(PS25970)
SHOE_UNREG
SHOE_ON
F4607
Q4601,
Q4603
CR-084
BOARD (1/2)
Q4606, 4607
B+ SWITCH
SHOE_UNREG
BATT_XEXT_CN
1-6
14
CN1003
ACV_UNREG
BATT_LI_3V
EP_8.5V
POWER (2/3)
(PAGE 3-7)
3-7. POWER BLOCK DIAGRAM (2/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-493 BOARD (2/3)
FP-741
FLEXIBLE
BOARD
ST-165 BOARD
FLASH UNIT
IC5201
XEX_RST
4
XFLASH_RST
CPC
CN1001
XINIT
E8 F_RP
SDO1
SIO2_SCS
EXIO/CF_ADDR[5]
EXIO/CF_ADDR[9]
SDRAM,
NAND
(9/18)
IC5104
AND GATE
(15/18)
D_2.8V
10
USB_3.5V
3
(For Check)
D
PCI_XRESET
L1001
R28
L19
AP9
AP11
STRB_CHARGE
XSTRB_FULL
ADAPTOR_DET
SHOE_ON
E
STROBE_ON
XSYS_RST
POWER (3/3)
(PAGE 3-8)
ADAPTOR_DET
XSYS_RST
ST_UNREG
MT_5.0V
L2102
AU_4.6V
L3304
AU_4.6V_IC_3301
31-34
SHOE_UNREG
GPIO_S[13]
GPIO_S[14]
HDMI_RST
CN1010
(2/2)
A_2.8V
D_2.8V
A_4.6V
D_-2.8V
33
34
35
36
XBB_RST
MS_PWR_ON
XHDMI_RST
A_4.6V
D4_-2.8V
FP-736
FLEXIBLE
BOARD
16 16
S001
LENS ADAPTOR
DETECT
CN7601
(2/2)
38
VCC
(FOR MIC)
FP-740
FLEXIBLE
BOARD
39
Unreg
FP-743 FLEXIBLE
BOARD (2/2)
CN1006
EP_8.5V
FP-737
FLEXIBLE
BOARD
CK-178 BOARD
CN6002 CN1006
EP_8.5V
CN6002
EP_8.5V
1
EP_8.5V
HOT
SHOE
CR-084 BOARD
(2/2)
CN7301
(2/2)
IC3001
COMPONET
OUT AMP,
D-TERMINAL
DRIVER
(1/2)
34
35
36
37
PD-324 BOARD
CN6003
16 16
UNREG
CN901
CN6101 L6103
1
EP_8.5V
Q6108, Q6109 CN6105
VDD
B+ SWITCH
18
XSTBY
FB6101
A_1.2V_2
D_1.2V_2
EP_2.8V
EP_4.6V
L2903
EP_2.8V
EP_4.6V
18 18
26 26
EP_2.8V
EP_4.6V
18 18
26 26
EP_2.8V
2
EP_4.6V
17
EP_2.8V
EP_4.6V
L6101
L6102
BL_CONT
HDMI SIGNAL
PROCESSOR
(12/18)
BL_-V
XHDMI_RST
IC3101
D_3.3V
VSSG
IC6102
30 30
20 20
BL_CONT
BL_-V
30 30
20 20
BL_CONT
14
BL_-V
3
28 28
D_2.8V
28 28
D_2.8V
16
S6001
D6005
RESET (ACCESS)
IC3202
L3202
HDMI
TRANSMITTER
(13/18)
BL_-V
14
BACKLIGHT
DRIVE
3
Q6101, Q6102
D_2.8V
XRST F4
L3203
BL_CONT
HI_XRESET
7 7
RESET
7 7
MS_PWR_ON
RESET# B2
FP-735
FLEXIBLE
BOARD
1
CE
D_3.3V
2.9V REG
(18/18)
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-7
3
MEMORY
STICK DUO
CN7401
CN1002
IC1005
4
CN7402
MS-363 BOARD
MS_VCC
VCC
9
D_2.8V
16
TOUCH
PANEL I/F
Q6107, Q6110,
Q6112, Q6113
15
VSS
BL_L
D6106-6108
BACKLIGHT
2.7 inch
WIDE COLOR
LCD UNIT
WITH TOUCH
PANEL
Q6111
18 31
BL_-V
LCD901
14
XSTBY 10
LCD DRIVE
DOWN
CONVERTER
(11/18)
XRSTX J21
D_1.5V
D_1.8V
2
17
IC2901
L2904
15-18
1-3
MICVCC
2
D_3.3V
EP_8.5V
2
PH-002
BOARD (2/2)
CN7603
BL_CONT
POWER (3/3)
(PAGE 3-8)
CN1007
(2/2)
MICVCC_R B6
BUFFER
(5/18)
MT_5.0V
Adapter Detect
XE_K
BT901
(LITHIUM BATTERY)
16
FP-739
FLEXIBLE
BOARD (2/2)
1
D_2.8V
C
VIDOE OUT,
AUDIO IN/OUT
(14/18)
IC2102
G20 H20 A28
FLASH
DRIVE
8 CHG G_IGBT 6
7 XINCHG
4 F_ON
XENON
LAMP
C5206
CHARGING
CAPACITOR
8
BATT_LI_3V
IC3301
L3305
Q3301
REG
A_4.6V
AU_4.6V
A_2.8V
D_2.8V
CMOS_4.1V
MT_5.0V
CAM_-1.0V
A_1.2V_2
D_1.2V_2
IC_2701_D_1.2V
D_2.5V
D_3.3V
D_1.8V
A_4.6V
D_1.5V
D_2.8V
A_2.8V
A_1.2V
D_1.2V
SW 2
PWM
EXTDA
4
5V REG
(13/18)
6
CONT
1
A_2.8V
D_2.8V
AU_2.8V
13, 14
3, 4
18
IC3201
CN3201
+5V_POWER
9
XE_A
K14 XRST
L3306
L3302
FB3301
13, 14
FP-745
FLEXIBLE
BOARD
CPU
(5/18 - 7/18)
A_1.2V
D_1.2V
CN1001
HDMI
OUT
A_1.2V
A_2.8V
A_2.8V
AU_2.8V
D_2.8V
CMOS_4.1V
MT_5.0V
CAM_-1.0V
A_1.2V_2
D_1.2V_2
IC_2701_D_1.2V
D_2.5V
D_3.3V
D_1.8V
A_4.6V
D_1.5V
D_2.8V
A_2.8V
B
D_2.5V
D_3.3V
D_1.8V
D_2.8V
D_1.2V
Adapter Detect
3
IC2101
POWER (1/3)
(PAGE 3-6)
1 VBAT
3 VCC
18
STRB_CHARGE
SCHARGE_ON
12
5
XSTRB_FULL
XSCHARGE_FULL
6
11
STROBE_ON
7
10
BATT_LI_3V
SHOE_UNREG
SHOE_ON
ST_UNREG
D_1.2V
A_1.2V
EP_2.8V
A_2.8V
AU_2.8V
D_2.8V
D_1.5V
A_4.6V
AU_4.6V
EP_4.6V
D_1.8V
D_3.3V
D_2.5V
IC_2701_D_1.2V
D_1.2V_2
A_1.2V_2
D4_-2.8V
CAM_-1.0V
MT_5.0V
CMOS_4.1V
BL_-V
BL_CONT
BATT_LI_3V
EP_8.5V
MT_5V
1
POWER (3/3)
(PAGE 3-8)
D5202
Q5201
IC2201
5
PCI_RESET AP19
T5201
8, 9
3
1
G2 RESET
8, 9
POWER (1/3)
(PAGE 3-6)
XSYS_RST
HI_XRESET
VTR_DD_ON
XFL_RST
CN5201
FLASH/CHARGE
CONTROL
+
9-6
A
ST_UNREG
CN5202
L5201
5-8
14-16
CN1008
17
3-8. POWER BLOCK DIAGRAM (3/3)
( ) : Number in parenthesis ( ) indicates the division number of schematic diagram where the component is located.
VC-493 BOARD (3/3)
L1701
A_1.2V
CLOCK
GENERATOR
(3/18)
26
CMOS_4.1V
A_2.8V
27
31
A_-1.0V
A_4.1V
A_2.8V
CN6601
15
IC6603
14
10
4
3.3V REG
(3/3)
11
4
3.3V REG
(3/3)
4
1.8V REG
(3/3)
4
2.8V REG
(3/3)
3
IC1702
CAMERA SIGNAL
PROCESSOR
(3/18)
XSYS_RST
D6 RST
IC1301
256M SDRAM
(8/18)
6M CMOS
IMAGER
(1/3)
3
IC6604
XRST F2
XINIT F4
32
VST_C_RESET
9
3
10
17 CRST
IC7201
IC1803
L7201
CAMERA
CONTROL
(4/18)
D_1.2V_2
IC6701
3
IC6606
CDS,
A/D CONVERTER
(1/18)
XSYS_RST
IC1901
IC6605
D6 RST
IC1201
CDS,
A/D CONVERTER
(2/18)
T4 PLLRST
AB4 XRST
XSYS_RST
XCLR
F23 STRB0
CAM_-1.0V
CMOS_4.1V
A_2.8V
D_2.8V
D_2.5V
STROBE_ON
30
XSYS_RST
D_2.8V
POWER (2/3)
(PAGE 3-7)
CN1202
CAM_-1.0V
L1702
D_1.2V
E
CM-077 BOARD
IC1701
A_2.8V
PITCH/YAW
SENSOR AMP
(2/3)
SE7202
RST_IC_5404 B14
PH2 F23
PITCH SENSOR
SE7201
CAM_-1.0V
CMOS_4.1V
MT_5.0V
D_1.2V
D_1.2V_2
FP-742 FLEXIBLE
BOARD
CN1005
15
D_1.2V_2
A_1.2V
A_1.2V_2
YAW SENSOR
128K EEPROM
(4/18)
A_4.6V
D_2.8V
D_1.5V
A_2.8V
XIC_5404_RST
LD-222 BOARD
CN5303
31
H11 XCLR
FB2701
FB2702
IC5404
MT_5.0V
IC2701
AUDIO/VIDEO
CODEC
(10/18)
D_2.8V
D_1.5V
A_4.6V
PCI_XRESET
8
7
6
MT_5.0V
D_2.8V
D_1.5V
A_4.6V
41, 42
D_1.8V
D_3.3V
IC_2701_D_1.2V
D
IC1804
4, 5
C
POWER (2/3)
(PAGE 3-7)
CAM_-1.0V
CMOS_4.1V
MT_5.0V
D_2.5V
A_4.6V
D_2.8V
D_1.5V
A_2.8V
FB5401
38
39
L5403
40
IC5405
4
M4 IHRSTX
POWER (2/3)
(PAGE 3-7)
FOCUS/ZOOM/NF
MOTOR DRIVE,
ND FILTER
DRIVE,
IRIS DRIVE
(1/4)
2.8V REG
(1/4)
3
CN5302
Z_MR_VCC
19
F_MR_VCC
15
D_2.8V
IC5402
MT_5.0V
D_2.8V
ZOOM MOTOR
NOISE FILTER
(1/4)
D1002
(NIGHTSHOT)
IC5703
L5701
FP-734 FLEXIBLE BOARD
CN1009
2
4
SIRCS_VDD
26
20
17
IC6503
REMOTE
COMMANDER
RECEIVER
XRST_IC_5703_CPU
XSYS_RST
VST_C_RESET
OPTICAL IMAGE
STABILIZATION
DRIVE
(2/4)
A6 XDL
A7 RESET_N
D5 CPU_PIO_0
20
26
29
TALLY_VDD
IC5801
L5801
D6502
(CAMERA RECORDING)
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
3-8E
IC5403
ZOOM MOTOR
NOISE FILTER
(1/4)
LENS BARRIER
DRIVE
(3/4)
LENS
BLOCK
4. PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
4-1. FRAME SCHEMATIC DIAGRAM
PD-324 BOARD (SIDE A)
SP901
SPEAKER
CN6001
1
1
1
24
CN6101
6
6
FP-744 FLEXIBLE BOARD
24
CN6003
39
1
CN6002
40
1
FP-737 FLEXIBLE
BOARD
CN6004
2 1
CK-178 BOARD (SIDE A)
1
24
CN6103
2
1
1
24
1
ST-165 BOARD
CN5201
1
+
1
6
6
1
6
CN6105
CN6102
2.7 INCH
WIDE COLOR
LCD MONITOR
TOUCH
PANEL
CONTROL
SWITCH
BLOCK
(SB25970)
LCD901
40
2
CN1006
39
1
18
FLASH UNIT
C5206
CHARGING
CAPACITOR
24
1
1
16
CN6002
1
FP-739 FLEXIBLE BOARD
2
39
1
1
39
CN1008
2
40
39
1
CN1006
39
1
38
CN3201
16
1
38
PH-002
BOARD
(SIDE B)
1
CN7603
14
1
PH-002 BOARD
(SIDE A)
1
CN1007
1
2
18
CN7604
20
CN1001
1
19
20
20
2
CN7602
6
39
1
1
CN901
HOT SHOE
1
CN7601
40
Active
Interface Shoe
14
1
18
39
CN1001
HDMI OUT
MIC901
MICROPHONE
UNIT
FP-736
FLEXIBLE
BOARD
FP-741 FLEXIBLE BOARD
FP-745
FLEXIBLE
BOARD
FP-740 FLEXIBLE
BOARD
16
18
CN5202
2
1
IC1804
(EEPROM)
LEVEL3
VC-493 BOARD (SIDE B)
CONTROL
SWITCH
BLOCK
(PS25970)
LEVEL3
VC-493 BOARD (SIDE A)
13
14
CN1004
1
2
45
1
14
1
41
CN1002
CN1202
13
14
CN1009
40
42
1
2
1
1
14
1
FP-734 FLEXIBLE
BOARD
2
80
1 5
2 6
IC2201
(Not supplied)
79
CN1010
2
1
J001
DC IN
14
CN1003
1
6
CN1005
44
FP-733 FLEXIBLE BOARD
1
FP-731 FLEXIBLE
BOARD
80
FP-742 FLEXIBLE
BOARD
1
BH001
BATTERY TERMINAL
14
45
FP-735
FLEXIBLE
BOARD
80
1
FP-743
FLEXIBLE
BOARD
45
1
1
14
(Coaxial cable)
1
CR-084 BOARD
(SIDE B)
50
51
1
2
2
1
14
1
CN7303
MULTI CONNECTOR
CN001
A/V OUT
1
1
41
CN6601
40
42
MS-363 BOARD
(SIDE B)
CN7402
MEMORY STICK
CONNECTOR
14
LEVEL3
LD-222 BOARD
(SIDE A)
CN5302
CN5303
LEVEL3
LD-222 BOARD
(SIDE B)
CN7401
MS-363 BOARD
(SIDE A)
LEVEL3
CM-077 BOARD
(SIDE B)
2
1
CN5301
10
CN7301
14
45
44
1
CN7302
1
LOCK
79
80
CR-084 BOARD
(SIDE A)
LENS BLOCK
10
LENS BARRIER
UNIT
1
FP-738 FLEXIBLE BOARD
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-1
FRAME
4-2. SCHEMATIC DIAGRAMS
Link
CK-178 BOARD (CONTROL SWITCH)
FP-731 FLEXIBLE BOARD (DC IN)
PD-324 BOARD (LCD DRIVE)
FP-733 FLEXIBLE BOARD
(BATTERY TERMINAL)
FP-744 FLEXIBLE BOARD (PANEL REVERSE)
FP-742 FLEXIBLE BOARD
(LD-VC CONNECTION)
MS-363 BOARD (MS CONNECTOR)
FP-736 FLEXIBLE BOARD
(VC-CK EXTENSION BOARD)
CR-084 BOARD (1/2)
(COMPONENT OUT, D-TERMINAL DRIVER)
FP-737 FLEXIBLE BOARD
(CK-PD CONNECTION)
CR-084 BOARD (2/2) (CONNECTOR)
FP-735 FLEXIBLE BOARD
(VC-MS CONNECTION)
FP-738 FLEXIBLE BOARD (A/V CONNECTOR)
FP-743 FLEXIBLE BOARD
(VC-CR CONNECTION)
FP-745 FLEXIBLE BOARD
(HDMI CONNECTOR)
PH-002 BOARD
(MIC, HOT SHOE, PS EXTENSION BOARD)
FP-739 FLEXIBLE BOARD
(VC-PH CONNECTION)
FP-740 FLEXIBLE BOARD (HOT SHOE)
FLASH UNIT
FP-734 FLEXIBLE BOARD
(REMOTE COMMANDER RECEIVER)
CONTROL SWITCH BLOCK (SB25970)
ST-165 BOARD (FLASH DRIVE)
CONTROL SWITCH BLOCK (PS25970)
COMMON NOTE FOR SCHEMATIC DIAGRAMS
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
FP-741 FLEXIBLE BOARD
(VC-ST CONNECTION)
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
4-2. SCHEMATIC DIAGRAMS
(ENGLISH)
THIS NOTE IS COMMON FOR SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)
(For schematic diagrams)
• All capacitors are in µF unless otherwise noted. pF : µ
µF. 50 V or less are not indicated except for electrolytics
and tantalums.
• Chip resistors are 1/10 W unless otherwise noted.
kΩ=1000 Ω, MΩ=1000 kΩ.
• Caution when replacing chip parts.
New parts must be attached after removal of chip.
Be careful not to heat the minus side of tantalum
capacitor, Because it is damaged by the heat.
• Some chip part will be indicated as follows.
Example
C541
L452
22U
10UH
TA A
2520
1. Connection
Pattern box
Color bar chart
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
Pattern box
Front of the lens
L
Kinds of capacitor
External dimensions (mm)
Case size
• Constants of resistors, capacitors, ICs and etc with XX
indicate that they are not used.
In such cases, the unused circuits may be indicated.
• Parts with ★ differ according to the model/destination.
Refer to the mount table for each function.
• All variable and adjustable resistors have characteristic
curve B, unless otherwise noted.
• Signal name
XEDIT → EDIT
PB/XREC → PB/REC
• 2: non flammable resistor
• 5: fusible resistor
• C: panel designation
• A: B+ Line
• B: B– Line
• J : IN/OUT direction of (+,–) B LINE.
• C: adjustment for repair.
(Measuring conditions voltage and waveform)
• Voltages and waveforms are measured between the
measurement points and ground when camera shoots
color bar chart of pattern box. They are reference values
and reference waveforms.
(VOM of DC 10 MΩ input impedance is used)
• Voltage values change depending upon input
impedance of VOM used.)
Camera
A B
A=B
Red
Blue
White
Magenta
H
Cyan
Green
Yellow
2. Adjust the distance so that the output waveform of
Fig. a and the Fig. b can be obtain.
B A
Fig. a (Video output terminal output waveform)
Electronic beam scanning frame
CRT picture frame
Fig.b (Picture on monitor TV)
Precautions for Replacement of Imager
• If the imager has been replaced, carry out all the adjustments
for the camera section.
• As the imager may be damaged by static electricity from
its structure, handle it carefully like for the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
When indicating parts by reference number, please
include the board name.
The components identified by mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le numéro
spécifie.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-2
ENGLISH
4-2. SCHEMATIC DIAGRAMS
JAPANESE
(JAPANESE)
回路図共通ノート
（他に必要なノートは各ブロックに記載してあります）
【回路図ノート】
1. 接続図
・ケミコン，タンタルを除くコンデンサで，耐圧50V以下のもの
はその耐圧を省略。単位はすべてμF（pはpF）。
・チップ抵抗で指示のないものは，1／10W以下。
kΩ＝1000Ω，MΩ＝1000kΩ
・チップ部品交換時の注意
取り外した部品は再使用せず，未使用の部品をご使用くださ
い。
タンタルコンデンサのマイナス側は熱に弱いため注意してくだ
さい。
・チップ部品には下記のように表示したものがあります。
例
C 541
L 452
22U
10UH
TA
A
2520
↑ ↑
↑
種類 ケースサイズ
外形寸法（mm）
・抵抗，コンデンサ，ICなど定数にXXがあるものは，使用して
いない事を示しています。このため，使用していない回路が記
載されている事があります。
・★印のある部品は，機種などにより異なりますので機能別マウ
ント一覧表を参照してください。
・可変抵抗と半固定抵抗で，B特性の表示を省略。
・信号名表記について，下記のような場合があります。
XEDIT → EDIT PB/XREC → PB/REC
・2は不燃性抵抗。
・1はヒューズ抵抗。
・Cはパネル表示名称。
・AはB＋ライン。
・BはB−ライン。
・JはBライン（＋，−）の入出力方向を示す。
・Cは調整名称。
パターンボックス
カラーバーチャート
For PTB-450:
J-6020-250-A
Pattern box PTB-450
J-6082-200-A
or
Small pattern box
PTB-1450
J-6082-557-A
For PTB-1450:
J-6082-559-A
L = 1 m (PTB-450)
L = 40 cm (PTB-1450)
パターンボックス
レンズ前面
L
カメラ
2. 図a及び図bの波形が得られるように画枠調整して下さい。
H
シ
黄 ア
ン
A B
マ
ゼ
白 ン
緑
ダ 赤
A=B
青
B A
図a（映像入出力端子出力波形）
電子ビーム走査線
【電圧・波形測定条件ノート】
・電圧値及び信号波形はパターンボックスのカラーバーチャート
を被写体としたときの測定点対アース間の参考値。
（デジタルマルチメータ；入力インピーダンス DC10MΩ使
用）
・使用テスタの入力インピーダンスにより電圧値が多少異なりま
す。
ブラウン管の画像枠
図b（テレビモニタの映像）
イメージャ交換時の注意
・イメージャを交換した場合は，カメラ部の全調整を
行ってください。
・イメージャは構造上，静電気により破壊される恐れが
あるため，MOS ICと同様に注意して取り扱ってくだ
さい。
また，受光部にはゴミの付着，および強い光がはいる
ことのないように注意してください。
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定して下さい。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-3
Schematic diagrams of the CM-077, VC-493 and LD-222 boards are not shown.
Pages from 4-4 to 4-28 are not shown.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
1
3
2
4
6
5
7
9
8
10
11
12
A
A
FP-736
FLEXIBLE
CN1006
Page 4-39
of Level 2
R6008
15k
EASY
24P
1
3
S6011
REG_GND
REG_GND
40
REG_GND
EP_8.5V
1
EP_8.5V
REG_GND
37
REG_GND
PANEL_R
38
PANEL_R
EP_2.8V
2
EP_2.8V
TP_X
35
TP_X
PANEL_G
36
PANEL_G
BL_-V
3
BL_-V
33 TP_SEL_1
PANEL_B
34
PANEL_B
TP_X
4
TP_X
TP_Y
REG_GND
32
REG_GND
TP_SEL_1
5
TP_SEL_1
29 REG_GND
BL_CONT
30
BL_CONT
TP_Y
6
TP_Y
D_2.8V
2
TP_SEL_1
4
B
TP_Y
31
27
REG_GND
28
D_2.8V
REG_GND
7
REG_GND
25
REG_GND
EP_4.6V
26
EP_4.6V
XBB_SCK
8
XBB_SCK
23
XBB_SCK
REG_GND
24
XCS_LCD
9
XCS_LCD
21
XCS_LCD
REG_GND
22
REG_GND
BB_SO
10
BB_SO
BB_SI
REG_GND
HI_XRESET
R6009
XX
RESET
DISP/
BATT INFO
3
3
1
XBATT_VIEW
S6001
BB_SO
BB_SO
19
BB_SI
17
BB_SI
BL_-V
20
BL_-V
EP_2.8V
18
EP_2.8V
PANEL_O/C
15
PANEL_OPEN/CLOSE
EP_8.5V
16
PANEL_NOR/REV
13
PANEL_NOR/REV
REG_GND
14
XMS_ACC_LED
11
MS_ACCESS_LED
REG_GND
12
REG_GND
KEY_AD3
9
PANEL_VD
10
PANEL_VD
HI_XRESET
7
RESET
KEY_AD0
8
KEY_AD0
REG_GND
5
REG_GND
PANEL_HD
6
PANEL_HD
3
SP+
1
SP-
SP+
1
C
SP-
KEY_AD3
CN6002
EP_8.5V
XBATT_VIEW
4
XBATT_VIEW
REG_GND
2
REG_GND
FP-737
FLEXIBLE
LND001-LND024
Page 4-39
of Level 2
40P
4
BB_SI
11
REG_GND
12
REG_GND
13
B
XBB_SCK
XCS_LCD
BL_CONT
BL_CONT
14
PANEL_VD
15
PANEL_VD
D_2.8V
16
D_2.8V
EP_4.6V
17
EP_4.6V
KEY_AD0
18
KEY_AD0
PANEL_HD
19
PANEL_HD
REG_GND
20
REG_GND
21
PANEL_R
22
PANEL_R
PANEL_G
23
PANEL_G
PANEL_B
24
PANEL_B
2
2
S6002
4
CN6003
39
KEY_AD0
REG_GND
C
REG_GND
D_2.8V
NIGHTSHOT
D
ON
N
BACK LIGHT
FILM ROLL INDEX
S6009
8
6
R6007
3900
R6004
1200
R6005
2700
R6006
2200
XX
D6006
1
3
S6010
4
4
2
S6003
SML-512UWT86
D6005
(ACCESS)
REG_GND
2
3
S6004
1
1
5
2 1
2
3
4
4
3
KEY_AD3
7
D
XMS_ACC_LED
OFF
FP-744
FLEXIBLE
REG_GND
6
REG_GND
5
N.C.
4
Page 4-31
of Level 2
REG_GND
E
N.C.
3
PANEL_NOR/REV
2
PANEL_NOR/REV
1
6P
2P
SP901
SPEAKER
REG_GND
D6009
XX
PANEL_NOR/REV
CN6001
E
CN6004
SP(+)
1
SP(-)
2
SP+
SP2
3
D6004
XX
1
S6007
(PANEL OPEN/CLOSE)
F
REG_GND
REG_GND
1
C
2
PANEL_O/C
3
F
4
XX
D6010
G
G
H
CK-178 BOARD
H
CONTROL SWITCH
XX MARK:NO MOUNT
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-29
CK-178
1
3
2
4
6
5
7
9
8
FP-737
FLEXBLE
LND301-LND324
(Page 4-39 of Level 2)
PANEL_B
24
BIN
PANEL_G
23
GIN
C6103
10u
6.3V
20
PANEL_HD
19
PANEL_XHD
KEY_AD0
18
KEY_AD
EP_4.6V
17
EP_4.6V
D_2.8V
16
D_2.8V
PANEL_VD
15
PANEL_XVD
BL_CONT
14
BL_CONT
11
BB_SI
8.5
C6124
0.01u
25V
3
R6135
220k
C6113
0.01u
25V
Q6108,Q6109
B+ SWITCH
A
D6104
XX
C6114 0.01u
BB_SO
0.01u
C6119
4.7u
6.3V
25V
C6120
10u
TP_SEL_1
5
TP_SEL1
TP_X
4
TP_X
3
BL_-V
EP_2.8V
2
EP_2.8V
EP_8.5V
1
EP_8.5V
C6108
0.1u
CN6101
LD6101
1.4
R6107 XX
BB_SI
REG_GND
0.2
R6108 XX
XCS_LCD
XBB_SCK
BB_SO
2.7
R6110 470
2.6
R6111 XX
0.3
2.8
CONTROL SWITCH BLOCK
(SB25970)
Page 4-42
of Level 2
2.6
PANEL_XHD
2
4.1
1.4
2.8
2.6
1.6
1.6
1.6
2.8
1.2
COMDA
COM
REF
XLED
BLDET
BIN
GIN
RIN
TEST
VR
IC6102
SO
GND2
CXM3006CR-T4
LCD DRIVE
XCS
PWM
XSCK
WIDE
SI
VST
VDD
VDD
SCAN
VCK
XHD
VSS
VST
22
21
PANEL_EN
20
EN
PANEL_DWN
19
DWN
18
VDD
17
VSS
C6125
1u
10V
R6145
1M
D6105
16
VSSG
14
XSTBY
13
PCG
12
HST
11
REF
10
TEST1
9
TEST2
PANEL_HCK2
8
HCK2
PANEL_HCK1
7
HCK1
PANEL_VP
6
PSIG
PANEL_VG
5
G
R
MAZS056008S0
PANEL_HST
C6126
4.7
PANEL_REF
PANEL_VB
R6126 XX
2.5
PANEL_VG
R6128 XX
2.5
PANEL_VR
2.5
2.8
0.1u
BL_ON
PANEL_VR
4
2.8
PANEL_VB
3
B
1.4
PANEL_RGT
2
RGT
1
COM
0
PANEL_VST
PANEL_VCK
PANEL_COM
3
4
5
6
7
8
9
REG_GND
0
R6152
2.1
2.8
PANEL_XVD
10 11 12
2.8
2.8
0.1
R6105
1200
R6103
XX
PANEL_EN
R6146 XX
PANEL_DWN
LED_1A
R6121
D6106
NSSW008DT-T108
(BACKLIGHT)
XX
4
2ND_ZOOM(T)
3
HOME_SW
2
REG_GND
1
XX
PANEL_HCK1
0
2ND_ZOOM(W)
R6147 XX
PANEL_HCK2
R6123
PANEL_RGT
R6148 XX
R6153
5
D6102
XX
LED_2A
D6107
NSSW008DT-T108
(BACKLIGHT)
R6106
XX
EP_4.6V
R6149 XX
R6118
XX
C6106
XX
10V
REG_GND
R6119
XX
R6124
XX
±0.5%
R6127
XX
±0.5%
E
0
BL_-V
E
R6129
XX
±0.5%
R6150 XX
R6154
2ND_S/S_SW
D
LD6102
LED_1A
PANEL_HST
CN6104
6
C
EN
2
DWN
PCG
1
XSTBY
HST
R6102
1500
0
2200
HCK2
R6101
PANEL_PCG
XX
with
TOUCH
PANEL
24P
CN6105
PANEL_XSTBY
REG_GND
B
LCD901
(1/2)
2.7 inch
WIDE
COLOR
LCD
UNIT
N.C.
15
5.5
PANEL_XSTBY
PANEL_VP
R6125 XX
VCK
KEY_AD
HCK1
6
VG
1.4
REG_GND
OPIN
RGT
5
VB
1.4
N.C.
OPOUT
VSS
4
VCC2
2.8
3
2ND_S/S_SW
GND1
XCLR
2
2ND_ZOOM(T)
0
Q6111
2SA207800LS0
SWITCH
2.5
VP
CLKIN
2ND_ZOOM(W)
C6123
1u
10V
C6121
0.1u
10V
FILTER2
XVD
1
CS
PANEL_VST
PANEL_VCK
R6104
0
CN6103
HOME_SW
COM
23
PANEL_PCG
R6109
68k
CH_GND
R6137
120k
1.2
1.2
C6109
560p
COMREF
R6112
91k
±0.5%
EXTDA
TP_Y
24
PANEL_COM
REG_GND
2.2
36 35 34 33 32 31 30 29 28 27 26 25
VCC1
XBB_SCK
6.3V
PANEL_COM
FILTER
XCS_LCD
PANEL_REF
R6122
10k
R6115
10k
±0.5%
9
Q6108
UNR32A300LS0
C6122
XX
25V
25V
EXTDA
10
0
2.8
PANEL_XSTBY
RIN
BB_SO
D
C6117
1u
16V
R6131
XX
XCS_LCD
6P
C6116
1u
16V
13 14 15 16 17 18 19 20 21 22 23 24
BB_SI
6
C6112
22u
6.3V
C6111
0.1u
10V
C6115
12
TP_Y
C6110
XX
4V
C6107
2.2u
6.3V
GIN
13
7
C6105
22u
4V
BIN
REG_GND
8
R6133
100k
REG_GND
REG_GND
BL_-V
C
12
10uH
21
24P
11
5.8
REG_GND
XBB_SCK
6
5
2
1
4
L6101
RIN
22
REG_GND
FB6101
EP_2.8V
REG_GND
B
8.5
L6102
48 47 46 45 44 43 42 41 40 39 38 37
PANEL_R
10uH
L6103
10uH
EP_8.5V
EP_4.6V
A
10
Q6109
MCH6305-TL-E-S
LED_3A
5
TP_BOT
4
R6120
XX
BL_ON
C6104
XX
10V
2.8
D_2.8V
TOUCH
PANEL
I/F
1
A_IN+
GND
3
2
C6118
XX
R6114
XX
±0.5%
LD6105
R6151 XX
LED_C
6
2
A_IN-
Q6106
XX
872901317
R6117
XX
6.3V
LED_2A
LED_1A
LED_3A
5
1
4
Q6103
XX
872905450
BL_L
F
2
REG_GND
EXTDA
0
3
4
6
1
2.8
D6103
XX
C6102
0.0047u
TOUCH
PANEL
I/F
2
C6101
0.0047u
B_IN+
Q6105
XX
872901317
Q6102
XP421F-TXE
6
5
4
2.8
D6101
XX
B_IN-
A_OUT
Q6104
XX
872901317
5
1
2
3
6
1
0
LCD901
(2/2)
TOUCH
PANEL
With
LCD
UNIT
B_OUT
TP_SEL1
R6116
XX
3
5
3
4
CN6102
EP_8.5V
Q6101
XP411F-TXE
Vcc
4
1
8
TP_R
TP_Y
7
2.8
6
2
5
3
2.8
F
R6113
XX
±0.5%
IC6101
XX
NC
TP_L
6P
D6108
NSSW008DT-T108
(BACKLIGHT)
TP_X
0
6
R6155
NC
TP_TOP
0
EP_2.8V
Q6110
UP04601008S0
BACKLIGHT
DRIVE
REG_GND
EXTDA
BL_ON
G
Q6107
UNR31A300LS0
BACKLIGHT
DRIVE
BL_CONT
C6127
XX
16V
R6134
47k
±0.5%
R6130
3k
±0.5%
6
2.6
2.8
1
2.8
R6136
47k
±0.5%
2.8
R6132
2.7
R6139
4700
±0.5%
1
5
2.1
R6142
2200
±0.5%
2.2
2.2
4
2
1
R6140
2200
±0.5%
2.1
2
6
Q6112
UP04401008S0
BACKLIGHT
DRIVE
3
1.6
1
1.6
5
3
G
4
1
R6138
100k
22k
REG_GND
REG_GND
R6143
100k
-9.5
1.6
Q6113
UP04601008S0
BACKLIGHT
DRIVE
H
BL_-V
R6141
1k
±0.5%
6
4
1
3
2
5
-10
-10.3
-10
BL_L
R6144
10
±0.5%
PD-324 BOARD
H
LCD DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-30
PD-324
4
3
A
S001
3
2
PANEL_NOR/REV
CN6001
Page 4-29
of Level 2
N.C.
1
REG_GND
REG_GND
A
B
B
B
CK-178
N.C.
4
A
Pin
1
(PANEL REVERSE)
B
A
6
C
C
C
MS_VCC
14
MS_VCC
13
REG_GND
12
MS_SCLK
11
REG_GND
10
MS_DATA3
9
MS_INSERT
8
MS_DATA2
7
REG_GND
6
MS_DIO
5
R7401
0
R7408
0
10
R7409
220
R7403
0
R7404
0 R7410 220
R7405
0
R7411
220
R7406
0
R7412
220
R7407
0
R7413
220
VSS
9
VCC
8
MS_SCLK
7
MSDATA3
6
XMS_IN
5
MSDATA2
4
MSDATA0
MS_DATA1
4
3
MSDATA1
MS_BS
3
2
MSBS
REG_GND
2
1
VSS
MS_O/C
1
14P
CN7402
12
PANEL_NOR/REV
4
3
2
1
10
MEMORY
STICK
DUO
11
2
1
C
1
10P
CN7401
LND001
FP-735
FLEXIBLE
Page 4-39
of Level 2
D
D
D
E
E
E
F
F
F
FP-744 FLEXIBLE BOARD
1
2
MS COVER
OPEN/CLOSE
SH_GND_A
LND002
4
3
S7401
SH_GND_B
XX
D001
D
E
MS-363 BOARD
F
MS CONNECTOR
PANEL REVERSE
XX MARK:NO MOUNT
05
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-31
FP-744, MS-363
1
3
2
4
6
5
7
9
8
10
11
12
A
LINE_CNT3
LINE_CNT2
B
LINE_CNT1
XD_CRADLE_DET
A
XD3_CRADLE_DET
B
A_2.8V
A_4.6V
D4_-2.8V
2.8
4.4
0
4.4
2.8
R3023
0
R3021
0
REG_GND
C3011
4.7u
6.3V
2
4.7
3
IC_2901_C/PB_OUT
IC_2901_PR_OUT
C3004
2.2u
C3005
2.2u
R0.5/P0.3
4
6.3V
5
R0.5/P0.3
6
6.3V
4.7
7
Vout2
Vin2
IC3001
TLS26A100PFBR
COMPONENT OUT AMP,
D-TERMINAL DRIVER
GND_1
Vin3
VCC28_2
Vout3
VEE_2
VCC46_2
Vout4
GND_2
TEST(GND)
Vout5
Vin5
TRG(GND)
LPF1_OFF
MONI(GND)
Vin6
XCS
S/XP
PS1
Vol_P2
Vol_P1
Vin7
Vol_Y1
Vol_Y2
D
R3022
0
SEL3
SEL2
SEL1
DET_IN
Cont_out3
Cont_out2
DET_OUT
Cont_out1
VCC46_1
Vin4
12
Cont_in3B
VEE_1
9
11
Cont_in2
Vout1
Vin1
8
10
Cont_in3A
VCC28_1
Cont_in1A
2.8
C
36
0
35
-2.9
R3018
75
±5%
D3_LNO_Y
R3019
75
±5%
D3_LNO_PB
R3020
75
±5%
D3_LNO_PR
34
0
33
2.8
32
0
31
-2.9
30
29
28
27
26
25
D
SI
1
R0.5/P0.3
C3010
4.7u
6.3V
D_GND
C3003
2.2u
6.3V
CK
IC_2901_Y_OUT
C3014
4.7u
6.3V
VCC_D2.8V
C
Cont_in1B
48 47 46 45 44 43 42 41 40 39 38 37
13 14 15 16 17 18 19 20 21 22 23 24
XCS_DDRA
XBB_SCK
2.6
BB_SO
0.3
C3008
1u
10V
R3024
0
D_2.8V
2.8
E
E
F
F
G
G
CR-084 BOARD (1/2)
H
COMPONENT OUT, D-TERMINAL DRIVER
H
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
R:REC MODE
P:PB MODE
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-32
CR-084 (1/2)
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
ACV_UNREG
ACV_UNREG
3
6
ACV_UNREG
ACV_UNREG
5
8
ACV_UNREG
ACV_UNREG
7
10
ACV_UNREG
ACV_UNREG
9
12
ACV_UNREG
ACV_UNREG
11
14
ACV_UNREG
ACV_UNREG
13
16
N.C
N.C
15
18
N.C
N.C
17
20
ACV_GND
ACV_GND
19
22
ACV_GND
ACV_GND
21
24
ACV_GND
ACV_GND
23
26
ACV_GND
ACV_GND
25
28
ACV_GND
30
A_2.8V
A_4.6V
N.C
ACV_GND
31
A_2.8V
BATT/XEXT
33
40
42
44
46
AUDIO_R_I/O
JACK_AD_CRADLE
JACK_AD
A_4.6V
D_2.8V
REG_GND
REG_GND
REG_GND
Y_IN
REG_GND
REG_GND
REG_GND
47
PR_IN
49
REG_GND
REG_GND
51
54
AUDIO_R_I/O
S_Y_I/O
53
60
REG_GND
S_Y_I/O
36
35
BATT/XEXT_CR
34
USB_D+
LANC_DC
33
LANC_DC
32
USB_GND
LANC_SIG
31
LANC_SIG
30
USB_DET/VBUS
N.C
27
28
(USB_ID)
N.C
29
26
MULTI_JACK_IN
CTRL3
25
LINE_CNT3
24
REG_GND
CTRL2
23
LINE_CNT2
22
AUDIO_R
CTRL1
21
LINE_CNT1
20
AUDIO_L
DET
19
XD3_CRADLE_DET
18
REG_GND
Pr
17
D3_LNO_PR
16
S_Y_I/O
REG_GND
15
14
REG_GND
Pb
13
12
S_C_I/O
REG_GND
11
10
REG_GND
8
VIDEO_I/O
6
N.C
4
ACV_UNREG
2
ACV_UNREG
ACV_UNREG
1
VIDEO_I/O
55
S_C_I/O
57
REG_GND
S_C_I/O
59
64
LANC_DC
REG_GND
63
66
XD_CRADLE_DET
REG_GND
65
68
REG_GND
XCS_DDRA
67
XCS_DDRA
70
XBB_SCK
69
XBB_SCK
72
REG_GND
KEY_AD2
(DVD BURN)
BB_SO
71
BB_SO
74
REG_GND
USB_GND
73
76
REG_GND
USB_D+
75
USB_D+
78
REG_GND
USB_D-
77
USB_D-
80
USB_VBUS
USB_GND
79
VDR313
LANC_DC
VDR312
61
VDR311
VIDEO_I/O
USB_VCC
USB_DUSB_D+
IC_2901_PR_OUT
LANC_SIG
D
KEY_AD2
S_Y_I/O
62
KEY_AD2
37
BATT/XEXT_CR
IC_2901_C/PB_OUT
LANC_SIG
XD_CRADLE_DET
DVD BURN
USB_D-
S_C_I/O
52
JACK_AD
USB_GND
AUDIO_R_I/O
IC_2901_Y_OUT
45
REG_GND
JACK_AD_CRADLE
38
43
AUDIO_L_I/O
REG_GND
39
AUDIO_L_I/O
50
58
41
ACV_GND
JACK_AD_CRADLE
D4_-2.8V
41
48
56
ACV_GND
ACV_GND
39
PB_IN
REG_GND
ACV_GND
40
D_2.8V
37
D7316
XX
42
USB_VCC
BATT/XEXT_CR
35
D_-2.8V
REG_GND
D7315
XX
43 44
29
34
38
C
ACV_GND
ACV_GND
A
CN7303
(INTERFACE CONNECTER)
for Handycam station
27
32
36
AUDIO_L_I/O
ACV_GND
ACV_UNREG
VIDEO_I/O
Y
D3_LNO_Y
9
REG_GND
7
N.C
5
ACV_UNREG
3
CN7303
B
D3_LNO_PB
5
4
8
C
4
B
ACV_UNREG
7
Note: CN7303 (interface connecter) is not supplied,
but this is included in CR-084 board.
1
2
6
1
2
3
REG_GND
5
5
A
4
4
ACV_UNREG
3
3
2
1
2
1
D7314
XX
D7312
XX
ACV_UNREG
REG_GND
D
3
4
80P
2
CN7301
5
REG_GND
1
D7311
XX
FP-743
FLEXIBLE
CN7302
E
FP-738
FLEXIBLE
Page 4-34
of Level 2
F
C7302
220p
50V
50V
VDR315
14P
C7301
220p
VDR314
Page 4-40
of Level 2
FB7311
AUDIO_L_I/O
14
AUDIO_L_I/O
REG_GND_AV
13
REG_GND
AUDIO_R_I/O
12
REG_GND_AV
11
FB7312
E
AUDIO_R_I/O
REG_GND
LANC_SIG
LANC_SIG
10
MULTI_JACK_IN
9
JACK_AD
REG_GND_AV
8
REG_GND
LANC_DC
7
LANC_DC
REG_GND_AV
6
VIDEO_I/O
5
VIDEO_I/O
REG_GND_AV
4
REG_GND
R7311
0
REG_GND
S_C_I/O
3
S_C_I/O
REG_GND_AV
2
REG_GND
S_Y_I/O
1
S_Y_I/O
CR-084 BOARD (2/2)
F
CONNECTOR
XX MARK:NO MOUNT
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-33
CR-084 (2/2)
4
2
1
A
A
A
Note: CN1001 is not supplied, but this is included
in FP-745 flexible complete board.
Pin
20
GND
19
GND
1
TMDS_DATA2_SHIELD
18
TMDS_DATA2+
2
TMDS_DATA2_+
TMDS_DATA2-
3
TMDS_DATA2_-
GND
4
TMDS_DATA1_SHIELD
TMDS_DATA1+
5
TMDS_DATA1_+
VC-493
(13/18)
TMDS_DATA1-
6
TMDS_DATA1_-
GND
7
TMDS_DATA0_SHIELD
CN3201
Page 4-19
of Level 3
TMDS_DATA0+
8
TMDS_DATA0_+
TMDS_DATA0-
9
TMDS_DATA0_-
LND035
Pin
3
S_C_I/O
REG_GND_AV
VIDEO_I/O
REG_GND_AV
CR-084
(2/2)
S_Y_I/O
9
VIDEO_I/O
8
VIDEO/AUDIO_GND
7
JACK_AD
6
LANC_DC
5
REG_GND_AV
CN7302
10
4
MULTI_JACK_IN
3
Page 4-33
of Level 2
LANC_SIG
REG_GND_AV
12
AUDIO_R_I/O
13
REG_GND_AV
14
AUDIO_L_I/O
B
AUDIO_R
S_C_I/O
GND
10
TMDS_CLOCK_SHIELD
TMDS_CLOCK+
11
TMDS_CLOCK_+
TMDS_CLOCK-
12
TMDS_CLOCK_-
GND
13
DDC_CEC_GND
SCL
14
CEC
SDA
15
SCL
+5V_POWER
16
SDA
3
+5V_POWER
17
RESERVED
2
HPD
18
+5V_POWER
1
GND
19
HPD
LANC_DC
S GND
2
LANC_SIG
1
AUDIO_L
CN001
B
13
REG_GND_AV
11
2
14
S_Y_I/O
12
B
1
A/V OUT
C
C
C
CN1001
20
SH_GND_A
21
A
4
3
B
22
3
23
2
1
C
HDMI
OUT
D
D
D
D
E
E
E
E
F
F
F
FP-738 FLEXIBLE BOARD
A/V CONNECTOR
FP-745 FLEXIBLE BOARD
F
HDMI CONNECTOR
05
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-34
FP-738, FP-745
1
3
2
4
6
5
7
9
8
10
11
12
A
A
B
B
C7601
XX
25V
D7601
XX
5
4
4.7
Q7601
2SC584600LS0
BUFFER
R7607
2200
3
2
1
CN7602
MIC901
MICROPHONE UNIT
6P
1
INT_MIC_R
2
INT_MIC_GND
3
INT_MIC_L
4
INT_MIC_GND
5
INT_MIC_F
6
INT_MIC_GND
1.8
1.2
R7604
XX
R7601
10k
C
4.7
Q7602
2SC584600LS0
BUFFER
R
L
C
FRONT
R7608
2200
1.8
1.2
R7605
XX
R7602
10k
R7609
2200
4.7
MIC_GND
36
INT_MIC_R
35
G
D
XX
D7616
R7606
XX
R7603
10k
MIC_GND
34
INT_MIC_F
33
MIC_GND
32
1
SHOE_GND
SHOE_MIC_FL
31
2
MicFR
SHOE_MIC_RR
30
3
MicFL
SHOE_MIC_FR
29
4
MIC_GND
SHOE_MIC_RL
28
5
MicRR
MIC_GND
27
6
MicRL
ZOOM_VR
26
7
ID1
START/STOP
25
8
Unreg
XCHARGE_LED
24
9
Unreg
D_2.8V
23
XPHOTO_LED
22
XCAM_LED
21
CHARGE_LED_VDD
20
KEY_AD1
REG_GND
R7614
R7615
18
17
18
R7623
8200
R7620
17
REG_GND
16
220
XMODE_SW
15
R7622
1k
STROBE
13
100
ID2
12
R7621
11
N.C
10
SHOE_UNREG
9
SHOE_UNREG
8
SHOE_UNREG
7
SHOE_UNREG
6
N.C
5
SHOE_GND
4
SHOE_GND
3
SHOE_GND
2
SHOE_GND
1
39P
CN7601
R7619
1200
D_2.8V
REG_GND
15
KEY_AD1(STROBE SW)
14
START/STOP
13
XCHARGE_LED
12
CHARGE_LED_VDD
11
XPHOTO_LED
10
N.C.
14
9
MODE_LED_VDD
8
XCAM_LED
7
N.C.
6
REG_GND
5
KEY_AD1(PHOTO_REC)
4
KEY_AD1(PHOTO_FREEZE)
3
REG_GND
2
XPOWER_SW
1
XMODE_SW
CN7604
D7608
XX
D7609
XX
D7610
XX
D7611
XX
XX
XX
R7616
XX
R7617
XX
10
ID2
11
STROBE
12
LANC
13
SHOE_CONT
14
SHOE_GND
ZOOM_VR
16
19
ID1
14P
CN7603
XPOWER_SW
LANC_SIG
F
1.8
1.2
D7615
XX
37
R7618
XX
C7602
XX
25V
CONTROL
SWITCH
BLOCK
(PS25970)
Page 4-43
of Level 2
FP-740
FLEXIBLE
Page 4-36
of Level 2
D7620
XX
LND201-LND239
Page 4-41
of Level 2
38
F
LND001
18P
CHISSIS_GND
G
D7612
XX
PH-002 BOARD
H
E
D7619
XX
FP-739
FLEXIBLE
39
MICVCC
INT_MIC_L
D7618
XX
E
AU_4.6V_IC_3301
D7617
XX
D
Q7603
2SC584600LS0
BUFFER
H
MIC, HOT SHOE, PS EXTENSION BOARD
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-35
PH-002
3
4
A
GND
15
USB-
14
USB+
SHOE_GND
Pin
14
SHOE_CONT
SHOE_CONT
13
LANC
LANC
12
STROBE
STROBE
ID2
ID2
UNREG
Unreg
UNREG
Unreg
ID1
ID1
MIC_RL
MicRL
MIC_RR
MicRR
MIC_GND
MicGND
3
MIC_FL
MicFL
3
2
MIC_FR
MicFR
2
1
GND
SHOE_GND
1
A
B
B
B
PH-002
CN7603
Page 4-35
of Level 2
REG_GND
2.8
2.8
C
VC-493
(18/18)
SIRCS_VDD
4
OUT
1
1
SIRCS_SIG
CN1009
Page 4-24
of Level 3
TALLY_VDD
3
GND
HOT
SHOE
A
VCC
CN901
A
2
B
Pin
16
4
3
2
1
GND
2
1
REG_GND
IC6503
RS-770
C
C
REMOTE COMMANDER
RECEIVER
F_TALLY_LED
D6502
SML-512UWT86
TALLY LED
6
C
(CAMERA RECORDING)
D
D
D
D
E
E
E
E
F
F
F
FP-740 FLEXIBLE BOARD
FP-734 FLEXIBLE BOARD
HOT SHOE
REMOTE COMMANDER RECEIVER
(PRINTED WIRING BOARD is omitted.)
NO MARK:REC/PB MODE
05
F
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-36
FP-740, FP-734
Ver. 1.1 2007.07
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
6
5
7
T5201
A
1
4
C5203
10u
10V
C5206
70u
330V
3
CHARGING
CAPACITOR
LD5202
5
IC5201
TPS65552DGQR
FLASH/CHARGE CONTROL
I_PEAK
18P
ST_UNREG
ST_UNREG
C
FP-741
FLEXIBLE
Page 4-42
of Level 2
D
1.8
2
NC
4
SCHARGE_ON
5
XSCHARGE_FULL
6
STROBE_ON
7
Adapter Detect
8
ST_GND
9
ST_GND
10
ST_GND
11
ST_GND
12
REG_GND
13
REG_GND
14
NC
15
BATT_LI_3V
16
NC
17
MT_5V
18
2.8
Q5201
TIG022TS-S-TL-E
0
4
11
3
2
D5204
EDZ TE61 6.8B
C5205
XX
10V
C5201
0.1u
16V
CL5201
R5209
280
1
FLASH
DRIVE
1
3
G_IGBT
C5202
2.2u
10V
R5205
100
R5210
XX
18
XE_A
17
XE_A
16
XE_A
15
XE_A
14
N.C.
13
N.C.
12
ST_GND
11
ST_GND
10
N.C.
9
N.C.
8
XE_K
7
XE_K
6
XE_K
5
XE_K
4
N.C.
3
N.C.
2
Adapter Detect
1
REG_GND(ST_GND)
B
FLASH UNIT
Page 4-42
of Level 2
0
R5202
100k
±0.5%
CN5202
ST_UNREG
HGND
R5201
330k
±0.5%
CHG
XINCHG
9
4
F_ON
PGND
8
3
VCC
0
7
2
SW
5
6
1
VBAT
5
R5203
0
NC
10
8.3
8.3
12
R5204
4700
D5201
CRF02(TE85R)
B
11
6
2
C5204
220p
50V
10
D5202
CRF02(TE85R)
A
L5201
2.2uH
9
8
MC+
4
LD5201
3
2
GND
1
R5211
XX
R5206
1M
0
8
7
6
5
CN5201
18P
C
XX
R5212
XX
D
R5207
XX
C5301
XX
10V
D5307
XX
BH5301
BATTERY
HOLDER
1
D5308
C5302
XX
10V
E
XX
2
3
E
BT901
LITHIUM
BATTERY
Note: BT901 (lithium battery) is not included
in ST-165 complete board.
F
F
G
G
ST-165 BOARD
H
H
FLASH DRIVE
XX MARK:NO MOUNT
NO MARK:REC/PB MODE
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-37
ST-165
Ver. 1.1 2007.07
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
4
3
2
1
Pin
A
1
ACV_GND
2
ACV_GND
A
1PIN
LND095
REG_GND
REG_GND
LND096
45PIN
2PIN
LND093
DIRB0
DIRB0
LND094
44PIN
3PIN
LND091
LENS_COVER_OPEN
LENS_COVER_OPEN
LND092
43PIN
4PIN
LND089
DIRA0
DIRA0
LND090
42PIN
5PIN
LND087
LENS_COVER_CLOSE
LENS_COVER_CLOSE
LND088
41PIN
6PIN
LND085
EN0
EN0
LND086
40PIN
7PIN
LND039
LENS_COVER_LED_ON
LENS_COVER_LED_ON
LND084
39PIN
8PIN
LND038
PITCH_AD
PITCH_AD
LND083
38PIN
9PIN
LND037
YAW_AD
YAW_AD
LND082
37PIN
10PIN
LND036
XCS_IC_5404
XCS_IC_5404
LND081
36PIN
11PIN
LND035
REG_GND
REG_GND
LND080
35PIN
12PIN
LND034
PNDCK(13.5M)
PNDCK(13.5M)
LND079
34PIN
13PIN
LND033
REG_GND
REG_GND
LND078
33PIN
14PIN
LND032
REG_GND
REG_GND
LND077
32PIN
VC-493
(18/18)
15PIN
LND031
REG_GND
REG_GND
LND076
31PIN
CN1003
Page 4-24
of Level 3
16PIN
LND030
IC_2701_SYSCLK
IC_2701_SYSCLK LND075
30PIN
17PIN
LND029
REG_GND
REG_GND
LND074
29PIN
18PIN
LND028
REG_GND
REG_GND
LND073
28PIN
19PIN
LND027
CAM_SCK
CAM_SCK
LND072
27PIN
20PIN
LND026
XRST_IC_5703_CPU
XRST_IC_5703_CPU
LND071
26PIN
21PIN
LND025
NF_EN
NF_EN
LND070
25PIN
22PIN
LND024
EXT_CAM_VD
EXT_CAM_VD
LND069
24PIN
23PIN
LND023
NF_SW
NF_SW
LND068
23PIN
24PIN
LND022
EN1
EN1
LND067
22PIN
25PIN
LND021
CAM_SO
CAM_SO
LND066
21PIN
26PIN
LND020
XSYS_RST
XSYS_RST
LND065
20PIN
27PIN
LND019
CAM_SI
CAM_SI
LND064
19PIN
28PIN
LND018
LENS_TEMP_AD
LENS_TEMP_AD
LND063
18PIN
29PIN
LND017
VST_C_RESET
VST_C_RESET
LND062
17PIN
30PIN
LND016
IR_NOISE
IR_NOISE
LND061
16PIN
31PIN
LND015
XIC_5404_RST
XIC_5404_RST
LND060
15PIN
32PIN
LND014
THERM
THERM
LND059
14PIN
33PIN
LND013
ND_NOISE
ND_NOISE
LND058
13PIN
34PIN
LND012
DIRA1
DIRA1
LND057
12PIN
35PIN
LND011
REG_GND
REG_GND
LND056
11PIN
36PIN
LND010
DIRB1
DIRB1
LND055
10PIN
37PIN
LND009
N.C.
N.C.
LND054
9PIN
38PIN
LND008
D_2.8V
D_2.8V
LND053
8PIN
39PIN
LND007
D_1.5V
D_1.5V
LND052
7PIN
40PIN
LND006
A_4.6V
A_4.6V
LND051
6PIN
41PIN
LND005
MT_5.0V
MT_5.0V
LND050
5PIN
42PIN
LND004
MT_5.0V
MT_5.0V
LND049
4PIN
43PIN
LND003
N.C.
N.C.
LND048
3PIN
44PIN
LND002
MT_GND
MT_GND
LND047
2PIN
45PIN
LND001
MT_GND
MT_GND
LND046
1PIN
ACV_GND
3
A
A
Note: J001 is not included in
FP-731 flexible board.
ACV_GND
ACV_GND
COLD
ACV_GND
SW
N.C
1
3
2
J001
DC IN
HOT
N.C
ACV_UNREG
ACV_UNREG
ACV_UNREG
B
12
13
B
ACV_UNREG
B
ACV_UNREG
14
BATT/XEXT
LD-222
(4/4)
C
FP-731 FLEXIBLE BOARD
CN5303
Page 4-28
of Level 3
C
C
DC IN
05
1
2
3
4
A
D
A
Pin
BATT_GND
14
BATT_GND
13
BATT_GND
12
BATT_GND
BATT_GND
C
4
VC-493
(18/18)
BATT_GND
BATT_SIG
2
IC_2701_SYSCLK(27M)
B
VC-493
(18/18)
CN1005
Page 4-24
of Level 3
C
D
CN1004
N.C
B
PNDCK(13.5M)
1
Page 4-24
of Level 3
BATT_UNREG
B
E
BATT_UNREG
E
BATT_UNREG
BH001
BATTERY
TERMINAL
Note: BH001 is not included in FP-733 flexible board.
C
BATT_UNREG
3
BATT_UNREG
2
BATT_UNREG
1
FP-733 FLEXIBLE BOARD
C
F
FP-742 FLEXIBLE BOARD
F
LD-VC CONNECTION
BATTERY TERMINAL
(PRINTED WIRING BOARD is omitted.)
05
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-38
FP-731, FP-733, FP-742
1
2
A
B
3
4
5
6
7
39
REG_GND
REG_GND
40
REG_GND
REG_GND
37
REG_GND
PANEL_R
38
PANEL_R
TP_X
35
TP_X
PANEL_G
36
PANEL_G
TP_SEL1
33
TP_SEL_1
PANEL_B
34
PANEL_B
TP_Y
31
TP_Y
REG_GND
32
REG_GND
29
REG_GND
BL_CONT
30
BL_CONT
27
REG_GND
D_2.8V
28
D_2.8V
REG_GND
25
REG_GND
EP_4.6V
26
EP_4.6V
XBB_SCK
XBB_SCK
23
XBB_SCK
REG_GND
24
21
XCS_LCD
XCS_LCD
21
XCS_LCD
REG_GND
22
REG_GND
19
BB_SO
BB_SO
19
BB_SO
BL_-V
20
BL_-V
BB_SI
17
BB_SI
BB_SI
17
BB_SI
EP_2.8V
18
EP_2.8V
PANEL_OPEN/CLOSE
15
PANEL_O/C
PANEL_O/C
15
PANEL_OPEN/CLOSE
EP_8.5V
16
EP_8.5V
REG_GND
PANEL_NOR/REV
13
PANEL_NOR/REV
PANEL_NOR/REV
13
PANEL_NOR/REV
REG_GND
14
MS_ACCESS_LED
11
XMS_ACC_LED
XMS_ACC_LED
11
MS_ACCESS_LED
KEY_AD3
9
KEY_AD3
9
RESET
7
HI_XRESET
HI_XRESET
7
RESET
REG_GND
5
REG_GND
REG_GND
5
REG_GND
SP+
3
SP+
SP+
3
SP+
1
SPCN6002
SP-
SP-
1
SP-
REG_GND
REG_GND
40
REG_GND
REG_GND
39
PANEL_R
38
PANEL_R
REG_GND
37
REG_GND
PANEL_G
36
PANEL_G
TP_X
35
TP_X
PANEL_B
34
PANEL_B
TP_SEL_1
33
TP_SEL1
REG_GND
32
REG_GND
TP_Y
31
TP_Y
BL_CONT
30
BL_CONT
REG_GND
29
D_2.8V
28
D_2.8V
REG_GND
27
EP_4.6V
26
EP_4.6V
REG_GND
25
REG_GND
24
REG_GND
XBB_SCK
23
REG_GND
22
REG_GND
XCS_LCD
BL_-V
20
BL_-V
BB_SO
EP_2.8V
18
EP_2.8V
EP_8.5V
16
EP_8.5V
14
REG_GND
12
REG_GND
PANEL_VD
10
PANEL_VD
KEY_AD0
8
KEY_AD0
PANEL_HD
6
PANEL_HD
XBATT_VIEW
4
XBATT_VIEW
REG_GND
2
REG_GND
40P
KEY_AD3
KEY_AD3
CN1006
REG_GND
12
REG_GND
PANEL_VD
10
PANEL_VD
KEY_AD0
8
PANEL_HD
6
PANEL_HD
XBATT_VIEW
4
XBATT_VIEW
2
REG_GND
A
B
KEY_AD0
40P
CK-178
VC-493
(18/18)
CN6002
Page 4-29
of Level 2
CN1006
Page 4-24
of Level 3
C
8
FP-736 FLEXIBLE BOARD
C
VC-CK EXTENSION BOARD
05
1
24pin
A
B
1pin
C
2
3
4
1
2
PANEL_B
PANEL_B
LND324
LND002
PANEL_G
PANEL_G
LND323
LND003
PANEL_R
PANEL_R
LND322
LND004
REG_GND
REG_GND
LND321
LND005
REG_GND
REG_GND
LND320
LND006
PANEL_HD
PANEL_HD
LND319
LND007
KEY_AD0
KEY_AD0
LND318
MS_O/C
LND008
EP_4.6V
EP_4.6V
LND317
REG_GND
LND009
D_2.8V
D_2.8V
LND316
MS_BS
LND010
PANEL_VD
PANEL_VD
LND315
PD-324
MS_DATA1
LND011
BL_CONT
BL_CONT
LND314
MS_DIO
LND012
REG_GND
REG_GND
LND313
CN6101
Page 4-30
of Level 2
REG_GND
REG_GND
LND312
LND014
BB_SI
BB_SI
LND311
LND015
BB_SO
BB_SO
LND310
LND016
XCS_LCD
XCS_LCD
LND309
LND017
XBB_SCK
XBB_SCK
LND018
REG_GND
REG_GND
LND019
TP_Y
LND020
4
24pin
LND001
LND013
3
A
A
TO VC
1
1
VC-493
(18/18)
B
B
REG_GND
CN1002
Page 4-24
of Level 3
MS_O/C
REG_GND
MS_BS
MS_DATA1
MS_DIO
MS_DATA2
MS_DATA2
MS_INSERT
MS_INSERT
MS_DATA3
MS_DATA3
REG_GND
LND308
MS_SCLK
MS_SCLK
LND307
REG_GND
REG_GND
TP_Y
LND306
MS_VCC
MS_VCC
TP_SEL_1
TP_SEL_1
LND305
MS_VCC
MS_VCC
LND021
TP_X
TP_X
LND304
LND022
BL_-V
BL_-V
LND303
LND023
EP_2.8V
EP_2.8V
LND302
LND024
EP_8.5V
EP_8.5V
LND301
CN6003
Page 4-29
of Level 2
MS-363
REG_GND
REG_GND
CK-178
A
TO MS
14
CN7401
Page 4-31
of Level 2
B
14
1pin
FP-737 FLEXIBLE BOARD
C
C
FP-735 FLEXIBLE BOARD
C
VC-MS CONNECTION
CK-PD CONNECTION
(PRINTED WIRING BOARD is omitted.)
(PRINTED WIRING BOARD is omitted.)
05
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-39
FP-736, FP-737, FP-735
1
2
3
4
6
5
7
8
9
10
11
12
A
A
2
ACV_UNREG
4
ACV_UNREG
ACV_UNREG
3
2
ACV_UNREG
ACV_UNREG
1
6
ACV_UNREG
ACV_UNREG
5
4
ACV_UNREG
ACV_UNREG
3
8
ACV_UNREG
ACV_UNREG
7
6
ACV_UNREG
ACV_UNREG
5
10
ACV_UNREG
ACV_UNREG
9
8
ACV_UNREG
ACV_UNREG
7
12
ACV_UNREG
ACV_UNREG
11
10
ACV_UNREG
ACV_UNREG
9
14
ACV_UNREG
ACV_UNREG
13
12
ACV_UNREG
ACV_UNREG
11
16
N.C
N.C
15
14
N.C
ACV_UNREG
13
18
N.C
N.C
17
16
N.C
N.C
15
20
ACV_GND
ACV_GND
19
18
ACV_GND
N.C
17
22
ACV_GND
ACV_GND
21
20
ACV_GND
ACV_GND
19
24
ACV_GND
ACV_GND
23
22
ACV_GND
ACV_GND
21
26
ACV_GND
ACV_GND
25
24
ACV_GND
ACV_GND
23
28
ACV_GND
ACV_GND
27
26
ACV_GND
ACV_GND
25
30
ACV_GND
ACV_GND
29
28
ACV_GND
ACV_GND
27
32
N.C
ACV_GND
31
30
ACV_GND
ACV_GND
29
34
A_2.8V
BATT/XEXT
33
32
BATT/XEXT
N.C
31
36
A_4.6V
D_2.8V
35
34
D_2.8V
A_2.8V
33
A_2.8V
38
REG_GND
D_-2.8V
37
36
D_-2.8V
A_4.6V
35
A_4.6V
40
REG_GND
REG_GND
39
38
REG_GND
REG_GND
37
42
REG_GND
Y_IN
41
40
Y_IN
REG_GND
39
44
REG_GND
REG_GND
43
42
REG_GND
REG_GND
41
46
REG_GND
PB_IN
45
44
PB_IN
REG_GND
43
48
REG_GND
REG_GND
47
46
REG_GND
REG_GND
45
50
AUDIO_L_I/O
PR_IN
49
48
PR_IN
REG_GND
47
52
REG_GND
REG_GND
51
50
REG_GND
AUDIO_L_I/O
49
AUDIO_R_I/O
54
AUDIO_R_I/O
S_Y_I/O
53
52
S_Y_I/O
REG_GND
51
B
ACV_GND
C
A_2.8V
A_4.6V
AUDIO_L_I/O
D
1
ACV_GND
C
AUDIO_L_I/O
REG_GND
56
REG_GND
REG_GND
55
54
REG_GND
AUDIO_R_I/O
53
AUDIO_R_I/O
JACK_AD_CRADLE
58
JACK_AD_CRADLE
S_C_I/O
57
56
S_C_I/O
REG_GND
55
REG_GND
JACK_AD
60
JACK_AD
REG_GND
59
58
REG_GND
JACK_AD_CRADLE
57
JACK_AD_CRADLE
LANC_SIG
62
LANC_SIG
VIDEO_I/O
61
60
VIDEO_I/O
JACK_AD
59
JACK_AD
LANC_DC
64
LANC_DC
REG_GND
63
62
REG_GND
LANC_SIG
61
LANC_SIG
66
XD_CRADLE_DET
REG_GND
65
64
REG_GND
LANC_DC
63
LANC_DC
68
REG_GND
XCS_DDRA
67
66
XCS_DDRA
XD_CRADLE_DET
65
70
REG_GND
XBB_SCK
69
68
XBB_SCK
REG_GND
67
72
KEY_AD2
(DVD BURN)
BB_SO
71
70
BB_SO
REG_GND
USB_GND
73
72
USB_GND
76
REG_GND
USB_D+
75
74
USB_D+
REG_GND
KEY_AD2
(DVD BURN)
REG_GND
69
74
78
REG_GND
USB_D-
77
76
USB_D-
REG_GND
75
80
USB_VBUS
USB_GND
78
USB_GND
REG_GND
77
USB_VBUS
79
79
80
E
F
B
CR-084
(2/2)
VC-493
(18/18)
CN7301
Page 4-33
of Level 2
CN1010
Page 4-24
of Level 3
D
71
73
E
F
G
G
H
FP-743 FLEXIBLE BOARD
H
VC-CR CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-40
FP-743
1
2
3
4
5
6
7
8
A
A
Pin
LND239
Pin
39
MICVCC
LND238
38
LND237
37
LND101
AU_4.6V_IC_3301
2
LND102
MICVCC
3
LND103
INT_MIC_L
LND104
MIC_GND
LND105
INT_MIC_R
LND106
MIC_GND
LND107
INT_MIC_F
INT_MIC_F
LND108
MIC_GND
LND109
SHOE_MIC_FL
SHOE_MIC_FL
LND110
SHOE_MIC_RR
SHOE_MIC_RR
LND230
LND111
SHOE_MIC_FR
SHOE_MIC_FR
LND229
LND112
SHOE_MIC_RL
SHOE_MIC_RL
LND228
LND113
MIC_GND
MIC_GND
LND227
LND114
ZOOM_VR
ZOOM_VR
LND115
START/STOP
LND116
XCHARGE_LED
VC-493
(18/18)
LND117
D_2.8V
LND118
XPHOTO_LED
CN1007
Page 4-24
of Level 3
LND119
XCAM_LED
LND120
CHARGE_LED_VDD
LND121
B
C
AU_4.6V_IC_3301
1
INT_MIC_L
MIC_GND
LND236
INT_MIC_R
LND235
MIC_GND
LND234
MIC_GND
LND232
LND231
LND226
START/STOP
LND225
XCHARGE_LED
LND224
D_2.8V
LND223
XPHOTO_LED
LND222
XCAM_LED
PH-002
CN7601
Page 4-35
of Level 2
LND221
CHARGE_LED_VDD
LND220
KEY_AD1
KEY_AD1
LND219
LND122
REG_GND
REG_GND
LND218
LND123
XPOWER_SW
XPOWER_SW
LND217
LND124
REG_GND
LND125
XMODE_SW
LND126
LANC_SIG
LND127
STROBE
LND128
REG_GND
B
LND233
LND216
XMODE_SW
LND215
LANC_SIG
LND214
STROBE
LND213
ID2
ID2
LND212
LND129
ID1
ID1
LND211
LND130
N.C
N.C
LND210
LND131
SHOE_UNREG
SHOE_UNREG
LND209
LND132
SHOE_UNREG
SHOE_UNREG
LND208
LND133
SHOE_UNREG
SHOE_UNREG
LND207
LND134
SHOE_UNREG
SHOE_UNREG
LND206
LND135
N.C
N.C
LND205
LND136
SHOE_GND
SHOE_GND
LND204
37
LND137
SHOE_GND
SHOE_GND
LND203
3
38
LND138
SHOE_GND
SHOE_GND
LND202
2
39
LND139
SHOE_GND
SHOE_GND
LND201
1
D
C
D
E
E
FP-739 FLEXIBLE BOARD
F
F
VC-PH CONNECTION
(PRINTED WIRING BOARD is omitted.)
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-41
FP-739
• Refer to page 4-2 (English), 4-3 (Japanese) for mark 0.
1
2
3
4
1
2
Pin
A
18
NC
17
BATT_LI_3V
16
1
MT_5V
2
NC
3
BATT_LI_3V
REG_GND
NC
REG_GND
HOME
A
W
VC-493
(18/18)
ST_GND
ST_GND
ST_GND
ST_GND
ST-165
CN1008
ST_GND
ST_GND
CN5202
Page 4-37
of Level 2
Adapter Detect
Adapter Detect
STROBE_ON
(ZOOM)
STROBE_ON
XSCHARGE_FULL
XSCHARGE_FULL
SCHARGE_ON
B
SCHARGE_ON
NC
B
NC
14
ST_UNREG
ST_UNREG
3
15
ST_UNREG
ST_UNREG
2
16
ST_UNREG
ST_UNREG
1
1PIN
LND001
HOME_SW
2PIN
LND002
2ND_ZOOM(W)
3PIN
LND003
2ND_ZOOM(T)
4PIN
LND004
2ND_S/S_SW
5PIN
LND005
N.C
6PIN
LND006
REG_GND
PD-324
S002
T
B
S001
START/STOP
CN6103
Page 4-30
of Level 2
FP-741 FLEXIBLE BOARD
C
C
C
VC-ST CONNECTION
CONTROL SWITCH BLOCK
(SB25970)
C
CONTROL SWITCH BLOCK (SB25970) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
(PRINTED WIRING BOARD is omitted.)
05
05
1
2
S001
3
4
LENS ADAPTOR
DETECT
ST_GND
A
Adapter Detect
LND023
1PIN
LND024
2PIN
LND001
LND050
XE_K
LND002
XE_K
XE_K
LND003
XE_K
LND004
COMMON
LND053
XENON
LAMP
4PIN
XE_K
LND052
N.C.
C001
0.033u
250V
TRIGEER
R001
1M
1/8W
5PIN
6PIN
7PIN
8PIN
9PIN
N.C.
10PIN
ST_GND
LND009
11PIN
ST_GND
LND010
12PIN
N.C.
ST-165
CN5201
Page 4-37
of Level 2
13PIN
N.C.
B
14PIN
XE_A
LND014
15PIN
XE_A
LND015
16PIN
XE_A
XE_A
LND016
17PIN
LND051
XE_A
LND017
18PIN
C
A
3PIN
N.C.
N.C.
B
A
S003
ST_GND
B
A
NC
REG_GND
Page 4-24
of Level 3
4
S004
Pin
MT_5V
3
FLASH UNIT
C
FLASH UNIT is replaced as block,
so that PRINTED WIRING BOARD is omitted.
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-42
FP-741, FLASH UNIT, SB25970
4
3
2
1
A
A
MODE
B
Pin
1
XMODE_SW
2
XPOWER_SW
3
REG_GND
XPOWER_SW
REG_GND
ON
XMODE_SW
B
POWER
OFF
(CHG)
S5313
(PHOTO FREEZE)
KEY_AD1(PHOTO_FREEZE)
PHOTO
S5312
KEY_AD1(PHOTO_REC)
(PHOTO REC)
REG_GND
N.C.
XCAM_LED
D5315
MOVIE
MODE_LED_VDD
CAMERA
N.C.
C
D5314
STILL
D5313
CHARGE
XPHOTO_LED
C
CHARGE_LED_VDD
XCHARGE_LED
S5314
START/STOP
START/STOP
S5311
KEY_AD1(STROBE SW)
16
REG_GND
17
D_2.8V
18
ZOOM_VR
FLASH
PH-002
D
CN7604
Page 4-35
of Level 2
RV103
W
(ZOOM)
T
D
E
F
E
CONTROL SWITCH BLOCK
(PS25970)
F
CONTROL SWITCH BLOCK (PS25970) is replaced as block,
so that PRINTED WIRING BOARD is omitted.
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-43
PS25970
4-3. PRINTED WIRING BOARDS
Link
CK-178 BOARD (SIDE A)
FP-745 FLEXIBLE BOARD
CK-178 BOARD (SIDE B)
PH-002 BOARD
PD-324 BOARD (SIDE A)
FP-734 FLEXIBLE BOARD
PD-324 BOARD (SIDE B)
ST-165 BOARD
FP-744 FLEXIBLE BOARD
FP-731 FLEXIBLE BOARD
MS-363 BOARD
FP-733 FLEXIBLE BOARD
CR-084 BOARD
FP-736 FLEXIBLE BOARD
FP-738 FLEXIBLE BOARD
COMMON NOTE FOR PRINTED WIRING BOARDS
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-3. PRINTED WIRING BOARDS
4-3. PRINTED WIRING BOARDS
(ENGLISH)
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS
•
•
: Uses unleaded solder.
: Circuit board
: Flexible board
Pattern from the side which enables seeing.
: pattern of the rear side
(The other layers’ patterns are not indicated)
• Through hole is omitted.
• There are a few cases that the part printed on diagram
isn’t mounted in this model.
• C: panel designation
• Chip parts.
Transistor
B
(JAPANESE)
プリント図共通ノート
【プリント図ノート】
・
・
：無鉛半田を使用しています。
：基板
：フレキシブル配線板
見ている面側のパターン。
：裏側のパターン
（他のパターンについては表示されていません）
・スルーホールは省略。
・プリント図には，本機で使用していない部品が記載されている
場合があります。
・Cはパネル表示名称。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-44
Diode
6 5 4 4 5 6 5
C
E
4 4
3
5
3
3
1 23
1 2 3 3 2 1 1 2 3 3 2 1
2
1 2
1 2
1
4
3
3
4 6 5 4 4 5 6
2
1 1 2 3 3 2 1
2 2
1 3
2
5 4 3 3 4 5 4
1
1
2
3
2
4
1
1 6 54
Printed wiring boards of the CM-077, VC-493 and LD-222 boards are not shown.
Pages from 4-45 to 4-48 are not shown.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
CK-178 (4 layers)
: Uses unleaded solder.
CK-178 BOARD (SIDE A)
2
1
CN6002
40
39
1
CN6003
24
1-871-820-
1
5
1
4
7
11
2
CN6004
S6009
6
8
ON
2
3
D6004
6
OFF
1
CN6001
NIGHTSHOT
D6006
1
D6009
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-49
CK-178 (SIDE A)
CK-178 (4 layers)
: Uses unleaded solder.
4
R6009
2
1
3
FILM ROLL INDEX
4
S6010
2
4
1
S6004
DISP/
BATT INFO
3
4
S6002
BACK LIGHT
05
2
1
3
S6003
3
S6007
2
D6010
3
1
2
R6006
1
PANEL
OPEN/CLOSE
4
R6007
CK-178 BOARD (SIDE B)
N
R6005
R6008
2
1-871-820-
K
D6005
11
R6004
(ACCESS)
4
S6011
3
4
3
S6001
1
EASY
2
1
RESET
A
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-50
CK-178 (SIDE B)
PD-324 (2 layers)
: Uses unleaded solder.
PD-324 BOARD (SIDE A)
R6121
24
1
CN6105
Q6112
R6132
R6140
4
3
R6151
R6130
R6139
6
1
4
3
R6149
R6138
R6154
R6136
R6134
R6150
Q6110
R6152
R6147
R6153
R6146
R6148
Q6104 Q6105 Q6106
B
C
E
B
C
E
B
C
E
R6116
B
LD6102
R6103
LD6105
R6102
Q6101
6
4
R6101
1
C6102
C
C6127
L6102
C6112
C6111
1
3
Q6102
3
1
R6127
R6119
D6102
R6122
C6101
D6105
1
C6120
R6104
R6105
1
6
3
4
6
D6101
C6126
C6125
4
C6123
E
R6137
C
B
Q6111
R6128
R6126
C6124
R6145
R6113
25
24
3
R6125
1
C6119
L6103
12
4
13
6
E
C6113
C6121
Q6109
C6114
R6135
D6104
C6116
C6122
R6131
C6118
R6114
IC6102
R6123
E
R6133
C
R6117
C6115
C6117
B
R6115
37
1
36
48
R6118
Q6107
6
1
3
4
4
R6124
1
C6103
Q6108
R6155
R6129
Q6103
C6109
R6120
IC6101
C6108
4
3
R6109
R6144
5
C6105
6
1
R6108
R6111
C6110
C6107
8
L6101
R6112
FB6101
R6110
R6107
CN6101
R6142
R6143
C6104
R6141
24
1
6
R6106
1
C6106
Q6113
LD6101
D6103
CN6103
6
CN6104
6
1
6
CN6102
1-871-779- 11
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-51
PD-324 (SIDE A)
PD-324 (2 layers)
: Uses unleaded solder.
PD-324 BOARD (SIDE B)
A
D6108
K
A
D6107
(BACK LIGHT)
K
A
D6106
K
1-871-779- 11
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-52
PD-324 (SIDE B)
FP-744 (1 layer), MS-363 (4 layers)
: Uses unleaded solder.
FP-744 FLEXIBLE BOARD
>PI<
FP-744
1-873-343
S001
(PANEL REVERSE)
6
4
S001
1
3
2
1
1-873-343- 11
05
MS-363 BOARD (SIDE B)
MS-363 BOARD (SIDE A)
CN7401
R7405
R7406
R7407
R7413
1
R7412
R7408
R7401
14
R7404
3
R7411
2
R7403
1
D001
4
12
R7410
MEMORY
STICK
DUO
11
S7401
R7409
MS COVER
OPEN/CLOSE
CN7402
LND002
LND001
1
05
10
1-871-818- 11
1-871-818-
11
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-53
FP-744, MS-363
CR-084 (6 layers), FP-738 (1 layer), FP-745 (2 layers)
: Uses unleaded solder.
80
79
5
A/V
OUT
VDR313
R7311
1
11
12
CN7302
CN7301
1 62
VDR315 C7302
CN001
FB7312
7 3 84
VDR312
14
C7301
9 5 10
VDR311
FB7311
13
14
4
1
3
>PI<
VDR314
FP-738 FLEXIBLE BOARD
CR-084 BOARD (SIDE B)
D7311
CR-084 BOARD (SIDE A)
1
FP738
2
1
C3003
C3004
C3005
05
14
D7316
R3023
D7315
1-873-337- 12
C3014
12
1
48
37
3
R3022
36
C3010
25
FP-745 FLEXIBLE BOARD
1
24
1-873-448- 11
5
4
IC3001
D7314
13
05
1
1-873-448- 11
21
3
4
D7312
1
R3021
05
20
43
5
2
R3018
42
41
1
44
C3011
R3019
R3024
CN7303
R3020
C3008
20
CN1001
(INTERFACE CONNECTOR)
HDMI
OUT
23
22
19
Note: CN7303 (interface connector) is not supplied,
but this is included in CR-084 complete board.
1
05
1-873-344- 11
Note: CN1001 is not supplied, but this is included
in FP-745 flexible complete board.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-54
CR-084, FP-738, FP-745
PH-002 (4 layers), FP-734 (1 layer)
: Uses unleaded solder.
PH-002 BOARD (SIDE B)
C7602
2
1
D7619
D7620
R7618
R7614
CN7601
2
1
D7616
3
R7601
3
1
1
2
R7607
C7601
E
R7604
B
C
14
R7615
R7602
R7603
R7609
38
R7608
39
R7605
R7606
E
B
E
C
C
Q7603
B
Q7602
5
1
D7601
4
3
Q7601
1
D7615
6
CN7603
R7617
CN7602
R7616
D7617
D7618
PH-002 BOARD (SIDE A)
1
3
R7619
1
D7608
2
2
1
D7609
D7610
2
2
3
3
R7620
D7611
1
1
3
D7612
R7623
2
R7622
3
1
18
R7621
LND001
CN7604
1-873-350- 11
05
05
1-873-350- 11
FP-734 FLEXIBLE BOARD
FP734
D6502
(CAMERA RECORDING)
6
4
3
1
2
IC6503
>PI<
1
1-873-333- 11
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-55
PH-002, FP-734
ST-165 (4 layers)
: Uses unleaded solder.
ST-165 BOARD
R5209
18
C5302
D5307
CL5201
D5308
1
CN5202
C5301
R5212
R5207
LD5202
D5204
R5211
R5202
1
CN5201
8
C5202
K
C5204
K
D5201
A
R5203
1
R5206
C5203
T5201
5
1-871-817- 11
3
4
2
A
6
R5205
D5202
1
Q5201
R5204
4
C5201
5
LD5201
5
1
1
CHARGING
CAPACITOR
BT901
C5205
R5201
C5206
BH5301
6
11
3
10
IC5201
18
2
R5210
L5201
05
BT901
BATTERY,
LITHIUM SECONDARY
Note: BT901 (lithium battery) is not included
in ST-165 complete board.
Note: Replace the battery holder (BH5301) together
when replacing the lithium battery (BT901) on the
ST-165 board. (The battery holder removed once
cannot be used again.)
When mounting these parts, mount new battery
holder first and attach new lithium battery next.
Note: ST-165基板のリチウム電池（BT901）を交換す
る場合はバッテリホルダ（BH5301）も同時に新
品に交換して下さい。（一度使用したバッテリ
ホルダは再使用できません。）
部品取り付けの際は，先にバッテリホルダを取
り付けてからリチウム電池を装着して下さい。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-56
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
ST-165
FP-731 (1 layer), FP-733 (2 layers), FP-736 (2 layers)
: Uses unleaded solder.
FP-731 FLEXIBLE BOARD
>PI<
mk OR
J001
DC IN
14
FP-733 FLEXIBLE BOARD
BH001
BATTERY
TERMINAL
1
3
Note: BH001 is not included in
FP-733 flexible board.
C
2
1
1
FP-731
05
1-873-330- 11
Note: J001 is not included in FP-731 flexible board.
1
2
4
14
1
05
1-873-332- 11
40
>PI<
CN1006
1-873-335
1
2
1
2
FP-736
CN6002
40
39
39
FP-736 FLEXIBLE BOARD
1-873-335- 12
05
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
4-57E
FP-731, FP-733, FP-736
NOTE
5. REPAIR PARTS LIST
NOTE: Characters A to Z of the electrical parts list indicate location of exploded views in which the desired part is shown.
EXPLODED VIEWS
Link
A
OVERALL SECTION
B
FRONT PANEL SECTION
E
MAIN BODY SECTION
C
LCD PANEL SECTION
F
TOP CABINET SECTION
I
LENS SECTION
Link
D
CABINET R SECTION
G
CABINET L SECTION
H
LENS/BT SECTION
J
BT PANEL SECTION
ELECTRICAL PARTS LIST
ACCESSORIES
CK-178 BOARD
D
FP-736 FLEXIBLE BOARD
D
PD-324 BOARD
C
CR-084 BOARD
J
FP-738 FLEXIBLE BOARD
J
PH-002 BOARD
F
FP-731 FLEXIBLE BOARD
H
FP-744 FLEXIBLE BOARD
D
ST-165 BOARD
H
FP-733 FLEXIBLE BOARD
J
FP-745 FLEXIBLE BOARD
H
FP-734 FLEXIBLE BOARD
B
MS-363 BOARD
E
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5. REPAIR PARTS LIST
5. REPAIR PARTS LIST
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from
the original one.
• Items marked “*” are not stocked since they are seldom required for routine
service. Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from
the parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF: µF
• COILS
uH: µH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
• SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
• Color Indication of Appearance Parts
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及び
セットに付いている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合
があります。
• *印の部品は常備在庫しておりません。
• コンデンサの単位でuFはμFを示します。
• 抵抗の単位Ωは省略してあります。
金 被：金属被膜抵抗。
サンキン：酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμ
A..., μPA..., μPB..., μPC..., μPD...を示します。
•
Abbreviation
AR : Argentine model
AUS : Australian model
BR : Brazilian model
CH : Chinese model
CND : Canadian model
EE : East European model
HK : Hong Kong model
J
: Japanese model
JE : Tourist model
KR : Korea model
NE : North European model
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-1
お願い
図面番号で部品を指定するときは基板名又はブロック
を併せて指定してください。
0印の部品，または0印付の点線で囲まれた部品は，
安全性を維持するために，重要な部品です。
従って交換時は，
必ず指定の部品を使用してください。
• 外装部品色表示
例：
(SILVER):セットの色を表す。
(Silver) : 部品の色を表す。
5. REPAIR PARTS LIST
DISASSEMBLY
5-1. EXPLODED VIEWS
HARDWARE LIST
5-1-1. OVERALL SECTION
Main Body Section
(See Page 5-6)
#2
1
#2
#2
#2
#2
#2
#1
Front Panel Section
(See Page 5-3)
#2
#2
#2
LCD Panel Section
(See Page 5-4)
2
Ref. No.
1
2
Part No.
Description
Ref. No.
3-215-117-01 PLATE, L ORNAMENTAL
3-215-111-01 COVER, HC
#1
#2
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-2
Part No.
Description
2-635-562-11 SCREW (M1.7) (Black)
2-635-562-31 SCREW (M1.7) (Black)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-2. FRONT PANEL SECTION
56
(9 mm x 14 mm)
55
#11
54
#3
52
57
51
#11
53
CAUTION:
For the part of 56, cut WOVEN (T0.25), FABRIC NON (3076-631-01) into the desired length and use it.
CAUTION:
56番は，T0.25ヒメロン
（3-076-631-01）
を切って使用。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
52
53
* 54
55
3-215-068-01
X-2178-953-1
A-1283-814-A
3-215-067-01
A-1217-971-A
RING, F
PANEL ASSY, F
FP-734 FLEXIBLE BOARD, COMPLETE
PLATE (F), GROUND
LENS BARRIER UNIT
56
* 57
#3
#11
CAUTION
3-219-855-01
2-660-401-01
3-078-890-11
SHEET, BARRIER
SHEET, FR
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW, TAPPING (Silver)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-3
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-3. LCD PANLE SECTION
Cabinet R Section
(See Page 5-5)
ns: not supplied
116
ns (Insulating
sheet (P))
(Note)
#2
115
LCD901
107
106
105
104
103
101
(Note)
108
114
#2
113
112
111
PD
-
ns
32
4
#11
117
109
110
(5 mm x 22 mm)
ns
#11
102
118
Note: Reuse the insulating sheet (P) when you exchange
the P cabinet (R).
CAUTION:
For the part of 110, cut WOVEN (T0.25), FABRIC NON
(3-076-631-01) into the desired length and use it.
Note: P キャビR の交換時は，絶縁シートP を再利用す
ること。
CAUTION:
110番は，T0.25ヒメロン
（3-076-631-01）
を切って使用。
Ref. No.
101
Part No.
Description
3-215-086-01 CABINET (R), P (CX7/CX7E/CX7K/CX7EK)
(Note)
101
102
103
104
3-215-086-11
A-1358-478-A
2-894-347-01
2-666-801-01
CABINET (R), P (CX6EK) (Note)
PD-324 BOARD, COMPLETE
REFLECTION SHEET (2.7J)
LIGHT GUIDE (2.7)
105
106
107
108
109
2-666-804-01
2-666-803-01
2-666-802-01
2-887-999-01
2-666-807-02
DIFFUSION SHEET (2.7)
PRISM SHEET H (2.7)
PRISM SHEET V (2.7)
FRONT FRAME (2.7J)
AG SHEET (2.7)
110
CAUTION
SHEET, FLEXIBLE GUARD
Ref. No.
Part No.
Description
* 111
112
113
114
2-638-780-01
1-480-279-11
3-215-091-01
3-215-092-01
CLIP
SWITCH BLOCK, CONTROL (SB25970)
CUSHION, TP
PLATE (P), GROUND
115
115
* 116
* 117
* 118
3-215-088-01
3-215-088-11
3-272-528-01
3-272-529-01
3-272-530-01
CABINET (L), P (J)
CABINET (L), P (EXCEPT J)
SHEET, HINGE
CUSHION (P (3))
CUSHION (P (2))
LCD901 A-1202-059-A TP BLOCK ASSY (27ESTMG07)
#2
2-635-562-31 SCREW (M1.7) (Black)
#11
3-078-890-11 SCREW, TAPPING (Silver)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-4
5. REPAIR PARTS LIST
DISASSEMBLY
HARDWARE LIST
5-1-4. CABINET R SECTION
#3
ns: not supplied
ns
162
163
(7 mm x 16 mm)
161
160
8
-17
CK
157
#3
ns
#3
ns
SP901
159
158
#1
ns
#2
156
154
151
CAUTION 1:
For the part of 154, cut SHEET, ADHESIVE (2-649-30001) into the desired length and use it.
(3 mm x 3.3 mm)
155
ns
152
CAUTION 1:
154番は，接着紙（2-649-300-01）
を切って使用。
153
CAUTION 2:
For the part of 162, cut WOVEN (T0.25), FABRIC NON
(3-076-631-01) into the desired length and use it.
CAUTION 2:
162番は，T0.25ヒメロン
（3-076-631-01）
を切って使用。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
152
153
154
155
3-215-089-01
2-668-087-01
X-2108-475-1
CAUTION 1
1-873-336-11
COVER (FRONT), HINGE
CLAMP, FLEXIBLE
HINGE ASSY
SHEET, ADHESIVE, HINGE
FP-737 FLEXIBLE BOARD
160
161
162
* 163
SP901
A-1283-816-A
A-1283-812-A
CAUTION 2
3-215-114-01
1-825-262-82
FP-736 FLEXIBLE BOARD, COMPLETE
CK-178 BOARD, COMPLETE
TAPE (0716)
SHEET (A), CM RADIATION
LOUD SPEAKER (1.6CM)
156
157
157
158
159
3-215-090-01
X-2178-955-1
X-2178-972-1
2-589-376-01
A-1283-815-A
COVER (REAR), HINGE
CABINET (R) ASSY (J)
CABINET (R) ASSY (E) (EXCEPT J)
FOOT (395), RUBBER
FP-744 FLEXIBLE BOARD, COMPLETE
#1
#2
#3
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-5
2-635-562-11 SCREW (M1.7) (Black)
2-635-562-31 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
5. REPAIR PARTS LIST
HARDWARE LIST
DISASSEMBLY
5-1-5. MAIN BODY SECTION
Top Cabinet Section
(See Page 5-7)
#2
#2
#2
#2
#2
Cabinet L Section
(See Page 5-8)
Lens/BT Section
(See Page 5-9)
201
#11
202
S
M 3
36
203
Note: When you exchange holder (MS), be sure to read
“1-6. PRECAUTION ON REPLACING THE HOLDER (MS)” on page 1-6.
204
#2
(Note)
Note: MSホルダー交換時は1-13ページの“1-6. MSホル
ダー交換時の注意”を必ずお読みください。
Ref. No.
Part No.
* 201
202
203
204
3-215-113-01
A-1283-813-A
1-873-334-11
A-1334-454-A
204
Description
Ref. No.
FRAME, MS
MS-363 BOARD, COMPLETE
FP-735 FLEXIBLE BOARD
HOLDER (CX7-J1), SERVICE (MS) (CX7: J)
(Note)
A-1334-455-A HOLDER (CX7-U2), SERVICE (MS) (CX7: US)
(Note)
204
204
204
204
204
204
204
A-1334-456-A HOLDER (CX7-CA2), SERVICE (MS) (CX7: CND)
(Note)
A-1334-457-A HOLDER (CX7E-CN2), SERVICE (MS)
(CX7E: CH) (Note)
A-1334-458-A HOLDER (CX7K-E23), SERVICE (MS)
(CX7K: E, JE) (Note)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-6
#2
#11
Part No.
Description
A-1334-459-A HOLDER (CX7K-KR2), SERVICE (MS)
(CX7K: KR) (Note)
A-1334-460-A HOLDER (CX7KE-E34), (MS)
(CX7EK: E, HK, AUS, JE) (Note)
A-1334-461-A HOLDER (CX7KE-CEN), (MS) (CX7EK: AEP)
(Note)
A-1334-462-A HOLDER (CX6EK-CEH), (MS) (CX6EK: AEP, UK)
(Note)
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-6. TOP CABINET SECTION
252
253
251
254
#1
CN901
255
#11
#11
#11
259
#1
#11
(13 mm x 23 mm)
256
257
MIC901
258
CAUTION:
For the part of 258 and 259, cut WOVEN (T0.25), FABRIC
NON (3-076-631-01) into the desired length and use it.
#3
(9 mm x 14 mm)
CAUTION:
258，259番は，T0.25ヒメロン
（3-076-631-01）
を切って
使用。
Ref. No.
251
252
253
253
254
* 255
256
Part No.
Description
Ref. No.
X-2178-954-1
3-215-112-01
1-480-273-11
1-480-273-21
CABINET ASSY, TOP
COVER, SHOE
SWITCH BLOCK, CONTROL (PS25970) (J)
SWITCH BLOCK, CONTROL (PS25970)
(EXCEPT J)
1-873-339-11 FP-740 FLEXIBLE BOARD
3-215-073-01 FRAME, SHOE
A-1283-811-A PH-002 BOARD, COMPLETE
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-7
Part No.
Description
257
258
259
1-873-338-11 FP-739 FLEXIBLE BOARD
CAUTION
SHEET, BARRIER
CAUTION
SHEET, MIC
CN901
MIC901
#1
#3
#11
1-818-890-11
1-542-711-11
2-635-562-11
2-660-401-01
3-078-890-11
CONNECTOR, EXTERNAL (HOT SHOE)
MICROPHONE UNIT
SCREW (M1.7) (Black)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-7. CABINET L SECTION
ns: not supplied
302
301
ns
304
#11
306
#11
303
307
#2
#11
#11
305
309
#2
308
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
301
302
302
303
* 304
3-215-104-01
X-2178-956-1
X-2178-973-1
2-589-376-01
3-215-106-01
BELT, GRIP
CABINET (L) ASSY (J)
CABINET (L) ASSY (E) (EXCEPT J)
FOOT (395), RUBBER
BRACKET (REAR), BELT
* 306
* 307
308
* 309
3-215-109-01
3-215-108-01
3-215-107-01
3-215-105-01
HEAT SINK, L
RETAINER, TRIPOD
SCREW, TRIPOD
BRACKET (FRONT), BELT
305
#2
#11
3-096-396-01 SHEET, TRIPOD
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-8
2-635-562-31 SCREW (M1.7) (Black)
3-078-890-11 SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
DISASSEMBLY
5-1-8. LENS/BT SECTION
ns: not supplied
354
BT901
(Note)
355
364
BH5301
(Note)
#3
ns
#3
#11
ST
5
16
#3
BT Panel Section
(See Page 5-11)
353
#3
356
352
365
#3
#3
357
360
351
#2
#3
Lens Section
(See Page 5-10)
VC
3
9
4
ns
! : BT901
(BATTERY, LITHIUM
SECONDARY)
Board on the mount position.
(See page 4-56.)
#3
358
J001
ns
363 362
#3
361
359
#3
ns
ns
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Note: Replace the battery holder (BH5301) together when replacing the lithium
battery (BT901) on the ST-165 board. (The battery holder removed
once cannot be used again.)
When mounting these parts, mount new battery holder first and attach
new lithium battery next.
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
Note: ST-165基板のリチウム電池（BT901）を交換する場合はバッテリホ
ルダ（B H 5 3 0 1 ）も同時に新品に交換して下さい。（一度使用した
バッテリホルダは再使用できません。）
部品取り付けの際は，先にバッテリホルダを取り付けてからリチウ
ム電池を装着して下さい。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
351
0 352
353
354
355
X-2176-859-1
1-480-263-21
3-215-050-01
3-215-051-01
1-873-340-11
HOLDER ASSY, ST
FLASH UNIT
HOLDER, CAPACITOR
CAP, CAPACITOR
FP-741 FLEXIBLE BOARD
356
* 357
358
* 359
360
A-1283-818-A
3-215-057-01
1-873-330-11
3-215-116-01
A-1283-995-A
FP-745 FLEXIBLE BOARD, COMPLETE
FRAME, JK
FP-731 FLEXIBLE BOARD
SHEET, VC RADIATION
VC-493 BOARD, COMPLETE (SERVICE)
(CX7/CX7K)
360
Ref. No.
Part No.
Description
360
A-1283-997-A VC-493 BOARD, COMPLETE (SERVICE)
361
362
363
1-873-341-11 FP-742 FLEXIBLE BOARD
3-215-216-01 SHEET, COVER (FP) ADHESIVE
3-215-119-01 COVER (FP)
(CX6EK)
364
365
0 BH5301
0 BT901
0 J001
A-1283-996-A VC-493 BOARD, COMPLETE (SERVICE)
(CX7E/CX7EK)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-9
#2
#3
#11
A-1283-810-A
3-270-979-01
1-756-615-31
1-756-134-12
1-815-792-11
ST-165 BOARD, COMPLETE
SPACER (HM)
HOLDER, BATTERY (Note)
BATTERY, STORAGE, LITHIUM (Note)
CONNECTOR, DC-IN (7.2V)
2-635-562-31 SCREW (M1.7) (Black)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
Ver. 1.1 2007.07
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-9. LENS SECTION
415
408
ns: not supplied
#3
414
416
IC6701
(Note 2, 3)
ns
CM
-07
#11
7
ns
#11
405
407
406
409
404
417
410
(Note 1)
(14 mm x 31 mm)
411
413
LD
22
-2
#3
403
402
(24.8 mm x 31 mm)
#3
#11
#3
412
401
CAUTION:
For the part of 403 and 417, cut WOVEN (T0.25), FABRIC
NON (3-076-631-01) into the desired length and use it.
Note 1: Refer to page 2-1 “Note for disconnecting the harness (coaxial cable)” when changing the harness
(coaxial cable).
CAUTION:
403番，417番は，T0.25ヒメロン
（3-076-631-01）
を切っ
て使用。
Note 1: ハーネス（coaxial cable）の交換時は2-1ページ
の“Note for disconnecting the harness (coaxial
cable)”を参照してください。
Note 2: Be sure to read “Precautions for Replacement of
Imager” on page 4-2 when changing the imager.
Note 3: IC6701 is not supplied, but this is included in
CMOS block assy.
Note 2: イメージャの交換時は4-3ページの“イメージャ
交換時の注意”を必ずお読みください。
Note 3: IC6701は交換対象ではありませんが，CMOS部
組に含まれます。
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 401
402
403
* 404
405
3-215-120-01
A-1283-808-A
CAUTION
X-2178-949-1
A-1227-735-A
PLATE (LD), GROUND
LD-222 BOARD, COMPLETE
SHEET (LF), INSULATING
FRAME (L) ASSY, LENS
LSV-1190A (SERVICE)
412
* 413
* 414
* 415
3-215-217-01
X-2178-950-1
3-096-389-01
3-215-114-01
SHEET, EX RADIATION
FRAME (R) ASSY, LENS
SHEET (252), CD RADIATION
SHEET (A), CM RADIATION
406
407
* 408
409
410
1-788-558-11
2-698-010-01
X-2178-951-1
A-1237-309-A
1-965-256-11
FILTER BLOCK, OPTICAL
RUBBER (1190), SEAL
HEAT SINK ASSY, CM
CM-077 BOARD, COMPLETE (SERVICE)
HARNESS (COAXIAL CABLE) (Note 1)
* 416
417
IC6701
3-215-115-01 SHEET (B), CM RADIATION
CAUTION
RETAINER, HARNESS
A-1209-688-A CMOS BLOCK ASSY (CMOS IMAGER)
* 411
3-217-389-01 GASKET (MC)
#3
#11
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-10
(Note 2,3)
2-660-401-01 SCREW (M1.7), NEW TRU-STAR, P2 (Red)
3-078-890-11 SCREW, TAPPING (Silver)
5. REPAIR PARTS LIST
HARDWARE LIST
5-1-10. BT PANEL SECTION
454
453
464
465
BH001
452
455
#11
456
462
#2
466
#3
451
458
#3
467
(9 mm x 14 mm)
457
#11
460
461
#3
CR
4
8
0
#3
459
463
CAUTION:
467番は，T0.25ヒメロン
（3-076-631-01）
を切って使用。
• Refer to page 5-1 for mark 0.
Ref. No.
Part No.
Description
Ref. No.
451
* 452
453
454
455
1-873-332-11
3-215-055-01
X-2178-952-1
X-2178-958-1
3-215-110-01
FP-733 FLEXIBLE BOARD
HEAT SINK, BT
PANEL ASSY, BT
COVER ASSY, JACK
COVER, DC
*
*
*
*
* 456
* 457
458
* 459
460
3-215-059-01
3-215-058-01
A-1283-817-A
3-219-758-01
A-1283-809-A
FRAME, CR
FRAME, AV
FP-738 FLEXIBLE BOARD, COMPLETE
SHEET, AV FLEXIBLE
CR-084 BOARD, COMPLETE
Part No.
Description
462
463
464
465
3-215-056-01
3-217-390-01
3-215-114-01
3-215-115-01
FRAME, BT
SHEET (743), FP
SHEET (A), CM RADIATION
SHEET (B), CM RADIATION
466
467
0 BH001
#2
#3
3-270-980-01
CAUTION
1-780-064-21
2-635-562-31
2-660-401-01
SPACER (BT)
SHEET, BARRIER
BATTERY TERMINAL BOARD
SCREW (M1.7) (Black)
SCREW (M1.7), NEW TRU-STAR, P2 (Red)
#11
461
CAUTION:
For the part of 467, cut WOVEN (T0.25), FABRIC NON
(3-076-631-01) into the desired length and use it.
1-873-342-11 FP-743 FLEXIBLE BOARD
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-11
3-078-890-11 SCREW, TAPPING (Silver)
CK-178
5-2. ELECTRICAL PARTS LIST
Ref. No.
Part No.
Description
Ref. No.
A-1283-812-A CK-178 BOARD, COMPLETE
**********************
< CONNECTOR >
* CN6001
CN6002
* CN6003
CN6004
1-816-654-51
1-816-926-11
1-816-650-51
1-778-506-21
FFC/FPC CONNECTOR (LIF) 6P
CONNECTOR, BOARD TO BOARD 40P
FFC/FPC CONNECTOR (LIF) 24P
PIN, CONNECTOR (PC BOARD) 2P
< DIODE >
D6005
6-500-817-01 DIODE (LED) SML-512UWT86 (ACCESS)
< RESISTOR >
R6004
R6005
R6006
R6007
R6008
1-218-954-11
1-218-958-11
1-218-957-11
1-218-960-11
1-218-967-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.2K
2.7K
2.2K
3.9K
15K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
< SWITCH >
S6001
S6002
S6003
S6004
S6007
1-771-138-21
1-771-138-21
1-771-138-21
1-771-138-21
1-786-148-11
SWITCH, KEY BOARD (RESET)
SWITCH, KEY BOARD (DISP/BATT INFO)
SWITCH, KEY BOARD (BACK LIGHT)
SWITCH, KEY BOARD (FILM ROLL INDEX)
SWITCH, PUSH (1 KEY) (PANEL OPEN/CLOSE)
S6009
S6010
S6011
1-771-731-21 SWITCH, SLIDE (NIGHTSHOT)
1-771-138-21 SWITCH, KEY BOARD (N)
1-771-138-21 SWITCH, KEY BOARD (EASY)
Electrical parts list of CM-077 board is not
shown.
Pages 5-13 is not shown.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-12
Part No.
Description
CR-084
Ref. No.
Part No.
FP-731
FP-733
FP-734
Description
FP-736
Ref. No.
Part No.
A-1283-809-A CR-084 BOARD, COMPLETE
***********************
(CN7303 (interface connector) is not supplied, but this is included in
CR-084 complete board.)
FP-738
FP-744
FP-745
Description
1-873-332-11 FP-733 FLEXIBLE BOARD
********************
(BH001 is not included in FP-733 flexible board.)
< BATTERY TERMINAL >
< CAPACITOR >
0 BH001
C3003
C3004
C3005
C3008
* C3010
1-165-884-91
1-165-884-91
1-165-884-91
1-165-908-11
1-112-746-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
2.2uF
2.2uF
1uF
4.7uF
10%
10%
10%
10%
10%
6.3V
6.3V
6.3V
10V
6.3V
* C3011
* C3014
C7301
C7302
1-112-746-11
1-112-746-11
1-164-933-11
1-164-933-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
4.7uF
220PF
220PF
10%
10%
10%
10%
6.3V
6.3V
50V
50V
1-780-064-21 BATTERY TERMINAL BOARD
A-1283-814-A FP-734 FLEXIBLE BOARD, COMPLETE
*******************************
< DIODE >
D6502
6-500-817-01 DIODE (LED) SML-512UWT86
(CAMERA RECORDING)
< IC >
< CONNECTOR >
IC6503
CN7301 1-817-920-11 CONNECTOR, FPC (ZIF) 80P
* CN7302 1-816-645-51 FFC/FPC CONNECTOR (LIF) 14P
0 CN7303 (Not supplied) CONNECTOR, MULTIPLE (SOCKET)
6-600-163-01 IC RS-770
A-1283-816-A FP-736 FLEXIBLE BOARD, COMPLETE
*******************************
< FERRITE BEAD >
< CONNECTOR >
FB7311 1-400-927-31 BEAD, FERRITE (1005)
FB7312 1-400-927-31 BEAD, FERRITE (1005)
CN1006 1-816-924-11 CONNECTOR BOARD TO BOARD 40P
CN6002 1-816-926-11 CONNECTOR, BOARD TO BOARD 40P
< IC >
IC3001
6-708-108-01 IC TLS26A100PFBR
A-1283-817-A FP-738 FLEXIBLE BOARD, COMPLETE
*******************************
< RESISTOR >
< CONNECTOR >
R3018
R3019
R3020
R3021
R3022
1-220-169-11
1-220-169-11
1-220-169-11
1-216-864-11
1-216-864-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
R3023
R3024
R7311
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-218-990-81 SHORT CHIP
75
75
75
0
0
5%
5%
5%
1/16W
1/16W
1/16W
CN001
1-815-794-13 CONNECTOR (MULTIPLE) (A/V OUT)
A-1283-815-A FP-744 FLEXIBLE BOARD, COMPLETE
*******************************
0
0
0
< SWITCH >
S001
1-786-680-21 SWITCH, DETECTION (SMD) (PANEL REVERSE)
< VARISTOR >
VDR311
VDR312
VDR313
VDR314
VDR315
1-803-974-21
1-803-974-21
1-803-974-21
1-803-974-21
1-803-974-21
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
VARISTOR, CHIP
(1608)
(1608)
(1608)
(1608)
(1608)
A-1283-818-A FP-745 FLEXIBLE BOARD, COMPLETE
*******************************
(CN1001 is not supplied, but this is included in
FP-745 flexible complete board.)
< CONNECTOR >
1-873-330-11 FP-731 FLEXIBLE BOARD
********************
(J001 is not included in FP-731 flexible board.)
Electrical parts list of LD-222 board is not
shown.
Pages 5-15 and 5-16 are not shown.
< CONNECTOR >
0 J001
CN1001 (Not supplied) CONNECTOR, HDMI (HDMI OUT)
1-815-792-11 CONNECTOR, DC-IN (7.2V)
• Refer to page 5-1 for mark 0.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-14
MS-363
Ref. No.
Part No.
Description
Ref. No.
Part No.
A-1283-813-A MS-363 BOARD, COMPLETE
***********************
PD-324
Description
< DIODE >
D6105
* D6106
* D6107
* D6108
< CONNECTOR >
* CN7401 1-816-645-51 FFC/FPC CONNECTOR (LIF) 14P
* CN7402 1-819-990-21 MEMORY STICK DUO CONNECTOR 10P
6-500-941-01
6-501-597-01
6-501-597-01
6-501-597-01
DIODE
DIODE
DIODE
DIODE
MAZS056008S0
NSSW008DT-T108 (BACKLIGHT)
NSSW008DT-T108 (BACKLIGHT)
NSSW008DT-T108 (BACKLIGHT)
< FERRITE BEAD >
< RESISTOR >
FB6101 1-400-331-11 FERRITE, EMI (SMD) (1005)
R7401
R7403
R7404
R7405
R7406
1-216-864-11
1-218-990-81
1-218-990-81
1-218-990-81
1-218-990-81
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R7407
R7408
R7409
R7410
R7411
1-218-990-81
1-218-990-81
1-218-945-11
1-218-945-11
1-218-945-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
0
220
220
220
5%
5%
5%
1/16W
1/16W
1/16W
R7412
R7413
1-218-945-11 RES-CHIP
1-218-945-11 RES-CHIP
220
220
5%
5%
1/16W
1/16W
< IC >
IC6102
8-753-229-98 IC CXM3006CR-T4
< COIL >
L6101
L6102
L6103
1-400-588-11 INDUCTOR
1-400-588-11 INDUCTOR
1-400-588-11 INDUCTOR
10uH
10uH
10uH
< TRANSISTOR >
< SWITCH >
S7401
1-786-680-21 SWITCH, DETECTION (SMD)
(MS COVER OPEN/CLOSE)
A-1358-478-A PD-324 BOARD, COMPLETE
***********************
Q6101
Q6102
Q6107
Q6108
Q6109
8-729-427-37
8-729-427-67
6-550-239-01
6-550-234-01
6-551-184-01
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
XP411F-TXE
XP421F-TXE
DTA144EMT2L
UNR32A300LS0
MCH6305-TL-E-S
Q6110
Q6111
Q6112
Q6113
8-729-054-48
6-550-232-01
8-729-054-49
8-729-054-48
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
UP04601008S0
2SA2029T2LQ/R
UP04401008S0
UP04601008S0
< RESISTOR >
< CAPACITOR >
C6101
C6102
C6103
C6105
C6107
1-100-581-81
1-100-581-81
1-165-989-11
1-127-895-91
1-165-884-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.0047uF
0.0047uF
10uF
22uF
2.2uF
10%
10%
10%
20%
10%
50V
50V
6.3V
4V
6.3V
R6101
R6102
R6104
R6105
R6109
1-218-957-11
1-218-955-11
1-218-990-81
1-218-954-11
1-218-975-11
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
2.2K
1.5K
0
1.2K
68K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
C6108
C6109
C6111
C6112
C6113
1-125-777-11
1-164-739-11
1-125-777-11
1-100-786-91
1-100-567-81
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.1uF
560PF
0.1uF
22uF
0.01uF
10%
5%
10%
20%
10%
10V
50V
10V
6.3V
25V
R6110
R6112
R6115
R6122
R6130
1-218-949-11
1-208-934-11
1-208-911-11
1-218-965-11
1-208-898-81
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
470
91K
10K
10K
3K
5%
0.5%
0.5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
C6114
C6115
* C6116
* C6117
C6119
1-100-567-81
1-100-567-81
1-112-298-91
1-112-298-91
1-127-760-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
1uF
1uF
4.7uF
10%
10%
10%
10%
10%
25V
25V
16V
16V
6.3V
R6132
R6133
R6134
R6135
R6136
1-218-969-11
1-218-977-11
1-208-927-11
1-218-981-11
1-208-927-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
22K
100K
47K
220K
47K
5%
5%
0.5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
C6120
C6121
C6123
C6124
C6125
1-165-989-11
1-125-777-11
1-165-908-11
1-100-567-81
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
1uF
0.01uF
1uF
10%
10%
10%
10%
10%
6.3V
10V
10V
25V
10V
R6137
R6138
R6139
R6140
R6141
1-218-978-11
1-218-977-11
1-208-699-11
1-208-691-11
1-208-683-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120K
100K
4.7K
2.2K
1K
5%
5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
C6126
1-125-777-11 CERAMIC CHIP
0.1uF
10%
10V
R6142
R6143
R6144
R6145
R6152
1-208-691-11
1-218-977-11
1-211-969-11
1-218-989-11
1-218-990-81
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
SHORT CHIP
2.2K
100K
10
1M
0
0.5%
5%
0.5%
5%
1/16W
1/16W
1/10W
1/16W
R6153
R6154
R6155
1-218-990-81 SHORT CHIP
1-218-990-81 SHORT CHIP
1-216-864-11 SHORT CHIP
< CONNECTOR >
*
*
*
*
CN6101
CN6102
CN6103
CN6105
1-785-905-51
1-794-322-51
1-794-322-51
1-785-905-51
FFC/CONNECTOR, FPC (ZIF) 24P
FFC/CONNECTOR, FPC (ZIF) 6P
FFC/CONNECTOR, FPC (ZIF) 6P
FFC/CONNECTOR, FPC (ZIF) 24P
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-17
0
0
0
PH-002
Ref. No.
Part No.
Description
Ref. No.
Part No.
A-1283-811-A PH-002 BOARD, COMPLETE
***********************
ST-165
Description
< COIL >
L5201
1-412-027-11 INDUCTOR
2.2uH
< CONNECTOR >
< TRANSISTOR >
*
*
*
*
CN7601
CN7602
CN7603
CN7604
1-817-544-71
1-816-654-51
1-816-645-51
1-816-647-51
CONNECTOR, FPC (ZIF) 39P
FFC/FPC CONNECTOR (LIF) 6P
FFC/FPC CONNECTOR (LIF) 14P
FFC/FPC CONNECTOR (LIF) 18P
0* Q5201 6-551-447-01 TRANSISTOR
< RESISTOR >
< TRANSISTOR >
Q7601
Q7602
Q7603
6-550-237-01 TRANSISTOR
6-550-237-01 TRANSISTOR
6-550-237-01 TRANSISTOR
TIG022TS-S-TL-E
2SC5658T2LQ/R
2SC5658T2LQ/R
2SC5658T2LQ/R
< RESISTOR >
R7601
R7602
R7603
R7607
R7608
1-218-965-11
1-218-965-11
1-218-965-11
1-218-957-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
10K
2.2K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7609
R7619
R7620
R7621
R7622
1-218-957-11
1-218-954-11
1-218-964-11
1-218-941-81
1-218-945-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
1.2K
8.2K
100
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R7623
1-218-953-11 RES-CHIP
1K
5%
1/16W
R5201
R5202
R5203
R5204
R5205
1-208-947-11
1-208-935-11
1-216-864-11
1-216-065-91
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
RES-CHIP
METAL CHIP
R5206
1-218-989-11 RES-CHIP
330K
100K
0
4.7K
100
0.5%
0.5%
1/16W
1/16W
5%
5%
1/10W
1/10W
1M
5%
1/16W
< TRANSFORMER >
0 T5201
1-443-568-21 TRANSFORMER, D.C.-D.C.CONVERTER
Electrical parts list of VC-493 board is not
shown.
Pages 5-19 to 5-25 are not shown.
A-1283-810-A ST-165 BOARD, COMPLETE
**********************
(BT901 (lithium battery) is not included in
ST-165 complete board.)
< BATTERY HOLDER >
0 BH5301 1-756-615-31 HOLDER, BATTERY (Note)
< BATTERY >
0 BT901
1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
< CAPACITOR >
C5201
C5202
C5203
C5204
0* C5206
1-107-826-11
1-125-889-91
1-165-875-11
1-163-001-11
1-112-730-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.1uF
2.2uF
10uF
220PF
70uF
10%
10%
10%
10%
16V
10V
10V
50V
330V
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
< CONNECTOR >
* CN5201 1-816-647-51 FFC/FPC CONNECTOR (LIF) 18P
* CN5202 1-816-647-51 FFC/FPC CONNECTOR (LIF) 18P
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
< DIODE >
D5201
0 D5202
D5204
6-501-096-01 DIODE CRF02 (TE85R)
6-501-096-01 DIODE CRF02 (TE85R)
8-719-083-91 DIODE EDZ TE61 6.8B
Note: Replace the battery holder (BH5301) together when replacing the lithium battery (BT901) on the ST-165 board. (The
battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
< IC >
0 IC5201
6-707-554-01 IC TPS65552DGQR
Note: ST-165基板のリチウム電池（BT901）を交換する場合は
バッテリホルダ（B H 5 3 0 1）も同時に新品に交換して下さ
い。（一度使用したバッテリホルダは再使用できませ
ん。）
部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム電池を装着して下さい。
• Refer to page 5-1 for mark 0.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-18
Ver. 1.2 2007.11
The changed portions from
Ver. 1.1 are shown in blue.
• EXCEPT J MODEL
to J MODEL
Checking supplied accessories.
Note: This item is supplied with the unit as an accessory, but is
not prepared as a service part.
AC Adaptor
(AC-L200/L200B)
* Compatible in
L200 and L200B.
0 1-479-285-21
Rechargeable Battery Pack
Conversion (2P) Adaptor
(NP-FH60)
0 1-569-007-12
0 A-1201-666-A (US, CND)
(E: NTSC, JE)
0 A-1201-667-A
(EXCEPT US, CND, CH)
0 A-1201-668-A (CH)
Power Cord
0 1-790-107-61 (US, CND)
0 1-833-892-21 (KR)
0 1-824-910-71 (AEP, E: PAL)
0 1-555-074-91 (AUS)
0 1-792-549-41 (JE)
0 1-834-852-11 (E: NTSC)
0 1-832-121-31 (CH)
0 1-827-269-12 (UK, HK)
Handycam Station
(DCRA-C191)
1-821-282-21
Component Video Cable
1-829-414-61
A/V Connecting Cable
1-823-156-51
USB Cable
1-829-868-31
Wireless Remote Commander
(RMT-835)
1-479-275-41
21-pin Adaptor
1-770-783-21
(AEP, UK)
Memory Stick PRO Duo (4GB)
(HDR-CX6EK/CX7K/CX7EK) (Note)
DVD-ROM
“ENJOY HANDYCAM”
3-093-691-01 (KR)
ENGLISH/KOREAN/JAPANESE
3-093-691-11 (US, CND)
ENGLISH/FRENCH/SPANISH/PORTUGUESE
3-093-691-21 (UK)
ENGLISH/RUSSIAN/GERMAN
3-093-691-51 (AEP)
ENGLISH/FRENCH/GERMAN/DUTCH/
PORTUGUESE/ITALIAN/RUSSIAN
3-093-691-61 (E, HK, AUS, CH)
ENGLISH/FRENCH/SIMPLIFIED CHINESE for CHINA/
TRADITIONAL CHINESE for HONG KONG
3-093-691-71 (E)
ENGLISH/TRADITIONAL CHINESE for TAIWAN/
SPANISH/PORTUGUESE
• Refer to page 5-1 for mark 0.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-26
Ver. 1.2 2007.11
The changed portions from
Ver. 1.1 are shown in blue.
Operating Guide
3-214-660-11 (ENGLISH) (CX7: US, CND/CX7K: E, JE)
3-214-660-21 (FRENCH) (CX7: CND)
3-214-660-31 (SPANISH) (CX7: US/CX7K: E, JE)
3-214-660-41 (PORTUGUESE) (CX7K: JE)
3-214-660-51 (TRADITIONAL CHINESE) (CX7K: E)
3-214-660-61 (KOREAN) (CX7K: KR, JE)
3-214-661-12 (ENGLISH) (CX6EK/CX7EK: AEP, E, HK, AUS, JE)
3-214-661-21 (FRENCH, DUTCH) (CX6EK: AEP/CX7EK: AEP)
3-214-661-31 (GERMAN, ITALIAN, TURKISH) (CX6EK: AEP/CX7EK: AEP)
3-214-661-41 (SPANISH, POLISH, GREEK) (CX6EK: AEP/CX7EK: AEP)
3-214-661-51 (RUSSIAN, SWEDISH) (CX6EK: AEP/CX7EK: AEP, JE)
3-214-661-61 (DANISH, FINNISH, POLISH) (CX6EK: AEP/CX7EK: AEP)
3-214-661-71 (CZECH, HUNGARIAN, SLOVAK) (CX6EK: AEP/CX7EK: AEP)
3-214-661-82 (SIMPLIFIED CHINESE) (CX7E/CX7EK: E, JE)
3-214-662-31 (TRADITIONAL CHINESE) (CX7EK: HK)
3-214-662-41 (ARABIC, PERSIAN) (CX7EK: E)
Handycam Handbook (PDF)
CD-ROM
“Handycam Application Software”
(“Picture Motion Browser (Software)”/
“Picture Motion Browser Guide”/
“Handycam Handbook (PDF)”)
3-214-682-02
The CD-ROM supplied contains all of language version of
the Handycam Handbook (PDF) for printing.
・ The printed matter is not supplied. If required, please
order it with the part number below.
・ (Only for destination Japanese model)
日本国内については日本語のみが印刷での部品供給
可能です。
HDR-CX7
3-214-656-01 (JAPANESE)
HDR-CX6EK/CX7E/CX7EK
3-214-657-11 (ENGLISH)
3-214-657-21 (FRENCH)
HDR-CX7/CX7K
3-214-657-31 (GERMAN)
3-214-656-11 (ENGLISH)
3-214-657-41 (DUTCH)
3-214-656-21 (FRENCH)
3-214-657-51 (TURKISH)
3-214-656-31 (SPANISH)
3-214-657-61 (SPANISH)
3-214-656-41 (PORTUGUESE)
3-214-657-71 (PORTUGUESE)
3-214-656-51 (TRADITIONAL CHINESE) 3-214-657-81 (ITALIAN)
3-214-656-61 (KOREAN)
3-214-657-91 (GREEK)
3-214-658-11 (RUSSIAN)
3-214-658-21 (SWEDISH)
3-214-658-31 (DANISH)
3-214-658-41 (FINNISH)
3-214-658-51 (POLISH)
3-214-658-61 (CZECH)
3-214-658-71 (HUNGARIAN)
3-214-658-81 (SLOVAK)
3-214-658-91 (SIMPLIFIED CHINESE)
3-214-659-11 (THAI)
3-214-659-21 (INDONESIAN)
3-214-659-31 (MALAY)
3-214-659-41 (TRADITIONAL CHINESE)
3-214-659-51 (ARABIC)
3-214-659-61 (PERSIAN)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-27
Ver. 1.2 2007.11
Ｖer. 1.1からの変更部分は
青色で記載されています。
• J MODEL
付属品
AC アダプター
（AC-L200/L200B）
* L200とL200Bには
互換性があります。
0 1-479-285-21
電源コード
0 1-792-549-41
DVD-ROM
「エンジョイハンディカム」
3-093-691-01
英語/韓国語/日本語
D端子コンポーネント
ビデオケーブル
1-829-414-11
AV 接続ケーブル
1-823-156-51
取扱説明書
3-214-660-01 (日本語)
USB ケーブル
1-829-868-31
ワイヤレスリモコン
（RMT-835）
1-479-275-31
ハンディカムステーション
(DCRA-C190)
1-821-282-11
ハンディカム ハンドブック (PDF)
リチャージャブル
バッテリーパック
（NP-FH60）
0 A-1201-665-A
CD-ROM
「Handycam Application Software」
（「Picture Motion Browser」
（ソフトウェア）
/
「Picture Motion Browserガイド」/
「ハンディカム ハンドブック」
（PDF）
）
3-214-682-02
• 0マークについては，5-1ページを参照して下さい。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
5-28E
印刷用のハンディカム ハンドブック（PDF）は
全ての言語が付属品のCD-ROMに含まれています。
・ 印刷物は付属されておりません。
必要な場合は下記部品番号にて注文となります。
3-214-656-01 (日本語)
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK
RMT-835
LEVEL
2
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Hong Kong Model
Chinese Model
Korea Model
Tourist Model
Japanese Model
SERVICE MANUAL
Ver. 1.2 2007.11
SUPPLEMENT-1
File this supplement with the service manual.
(DI07-196)
• Addition of Attention Sentence of HELP
• Change of Repair Parts
• Revision of Accessories
Note: Please refer to Ver.1.2 of SERVICE MANUAL (9-852-210-32) for the revision of accessories.
& : Points added portion.
• Addition of Attention Sentence of HELP
HELP
Sheet attachment positions and procedures of processing the flexible boards/harnesses are shown.
THE METHOD OF ATTACHMENT OF FP-737 FLEXIBLE BOARD
&8
Install the hinge cover (front) in the hinge cover (rear).
Note: Avoid it so as not to nip the flexible board, and lock four claws while covering with the hinge cover (front) straight.
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
9-852-210-81
Sony EMCS Co.
2007K0500-1
© 2007.11
Published by Kohda TEC
& : Points added portion.
• Change of Repair Parts
5. REPAIR PARTS LIST
5-1. EXPLODED VIEWS
Page
5-5
Former
Ref. No.
156
Part No.
New
Description
Ref. No.
3-215-090-01 COVER (REAR), HINGE
356
365
156
Description
3-215-090-02 COVER (REAR), HINGE
_366
#3
#3
Part No.
357
356
365
#3
#3
357
5-9
#3
#3
* 366
3-219-660-01 SPACER (DC)
0 BT901 1-528-900-31 BATTERY, LITHIUM SECONDARY (Note)
0 BT901 1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
5-11
454
X-2178-958-1 COVER ASSY, JACK
454
X-2178-958-5 COVER ASSY, JACK
5-2. ELECTRICAL PARTS LIST
Page
Former
Ref. No.
Part No.
New
Description
Ref. No.
A-1358-478-A PD-324 BOARD, COMPLETE
***********************
5-17
< CONNECTOR >
< CONNECTOR >
* CN6101 1-819-913-71 CONNECTOR, FPC (ZIF) 24P
* CN6105 1-819-913-71 CONNECTOR, FPC (ZIF) 24P
A-1283-810-A ST-165 BOARD, COMPLETE
**********************
(BT901 (lithium battery) is not included in
ST-165 complete board.)
A-1283-810-A ST-165 BOARD, COMPLETE
**********************
(BT901 (lithium battery) is not included in
ST-165 complete board.)
< BATTERY >
< BATTERY >
0 BT901 1-528-900-31 BATTERY, LITHIUM SECONDARY (Note)
0 BT901 1-756-134-12 BATTERY, STORAGE, LITHIUM (Note)
The components identified by
mark 0 or dotted line with
mark 0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour la
sécurité.
Ne les remplacer que par une pièce
portant le numéro spécifié.
0印の部品，または0印付きの点線で囲まれた部品は，
安全性を維持するために重要な部品です。
従って交換時は，必ず指定の部品を使用して下さい。
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Description
A-1358-478-A PD-324 BOARD, COMPLETE
***********************
* CN6101 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P
* CN6105 1-785-905-51 FFC/CONNECTOR, FPC (ZIF) 24P
5-18
Part No.
Note: Replace the battery holder (BH5301) together when replacing the lithium battery (BT901) on the ST-165 board. (The
battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
Note: ST-165基板のリチウム電池（BT901）を交換する場合は
バッテリホルダ（B H 5 3 0 1）も同時に新品に交換して下さ
い。（一度使用したバッテリホルダは再使用できませ
ん。）
部品取り付けの際は，先にバッテリホルダを取り付けてか
らリチウム電池を装着して下さい。
注意
電池の交換は，正しく行わないと破裂する恐れがあり
ます。電池を交換する場合には必ず同じ型名の電池
又は同等品と交換してください。
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
—2—
HARDWARE LIST (1/4)
#1: M1.7 X 2.5
(Black)
2-635-562-11
#2: M1.7 X 4.0
(Black)
2-635-562-31
#3: M1.7 X 2.5
(Red)
2-660-401-01
1.7
2.5
1.7
4.0
#5: M1.7 X 3.5 (Tapping)
(Black)
3-080-204-01
#11: M1.7 X 4.0 (Tapping)
(Silver)
3-078-890-11
1.7
1.7
4.0
#13: M1.7 X 2.5 (Tapping)
(Silver)
3-085-397-01
1.7
1.7
2.5
#16: M1.4 X 2.5
(Silver)
2-586-337-01
2.5
#19: M1.2 X 4.0 (Tapping)
(Red)
3-086-156-21
1.4
1.5
2.5
1.4
1.4
1.5
#18: M1.4 X 2.5
(Silver)
2-635-591-21
1.7 2.2
1.7
5.0
#15: M1.4 X 1.5
(Silver)
3-062-214-01
1.7
#17: M1.7 X 1.5
(Silver)
2-586-389-01
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
4.0
#14: M1.7 X 2.5
(Silver)
2-599-475-11
2.5
3.5
1.6
#10: M1.7 X 4.0
(Silver)
2-599-475-31
1.7
1.7
1.7
5.0
#8: M1.7 X 3.5 (Tapping)
(Silver)
3-078-890-01
1.4
3.5
1.4
2.5
#7: M1.7 X 1.6
(Black)
7-627-552-18
1.7
3.5
1.7
2.5
#6: M1.4 X 1.7
(Silver)
2-598-474-01
#9: M1.7 X 5.0 (Tapping)
(Silver)
3-078-890-21
#4: M1.4 X 2.5 (Tapping)
(Dark Silver)
3-348-998-81
#20: M1.4 X 3.0
(Silver)
2-635-591-31
1.4
1.2
4.0
3.0
HARDWARE LIST (2/4)
#21: M1.4 X 3.0
(Black)
2-662-396-21
#22: M1.7 X 5.0 (Tapping)
(Silver)
3-083-261-01
#23: M1.7 X 4.0 (Tapping)
(Black)
3-080-204-11
1.7
1.4
5.0
3.0
#25: M1.7 X 3.0
(Black)
2-635-562-21
3.0
3.0
#36: M3.0 X 6.0
(Silver)
4-886-821-11
3.0
4.0
6.0
6.0
#38: M3.0 X 20.0 (Tapping)
(Silver)
7-685-651-79
2.0
4.5
#35: M4.0 X 6.0 (Tapping)
(Silver)
3-975-291-02
8.0
#37: M2.0 X 6.0 (Tapping)
(Black)
3-080-206-31
3.0
4.0
#34: M3.0 X 8.0
(Black)
3-077-331-41
6.0
#32: M2.0 X 4.5 (Tapping)
(Silver)
2-102-498-01
1.2
3.5
#33: M3.0 X 6.0
(Silver)
3-077-331-21
4.0
#31: M3.0 X 4.0
(Silver)
2-102-434-01
1.4
1.4
1.4
2.0
#30: M1.2 X 4.0 (Tapping)
(White)
3-086-156-11
2.5
#28: M1.4 X 4.0 (Tapping)
(Dark Silver)
3-348-998-61
1.4
2.0
#29: M1.4 X 2.5
(Black)
2-662-396-01
5.5
#27: M1.4 X 2.0
(Black)
2-662-396-11
1.7
1.7
1.7
4.0
#26: M1.4 X 2.0
(Silver)
2-635-591-11
3.0
#24: B1.7 X 5.5 (Tapping)
(Black)
4-679-805-11
#39: M2.6 X 5.0 (Tapping)
(Black)
7-685-791-09
#40: M2.0 X 4.0 (Tapping)
(Silver)
7-685-851-04
3.0
2.0
6.0
2.6
20.0
5.0
2.0
4.0
HARDWARE LIST (3/4)
#41: M3.0 X 8.0 (Tapping)
(Silver)
3-065-748-01
#42: M2.0 X 4.0 (Tapping)
(Silver)
7-628-253-00
#43: M1.7 X 4.0
(Red)
2-660-401-31
3.0
8.0
2.0
#46: M1.7 X 3.0
(Red)
2-660-401-11
1.7
3.0
#49: M2.0 X 4.0
(Black)
2-630-005-31
2.0
4.0
#48: M1.7 X 2.5
(Silver)
3-973-497-91
1.7
1.4
2.5
3.0
#50: M2.0 X 3.0
(Red)
2-891-494-11
1.7
3.0
#47: M1.4 X 3.0 (Tapping)
(Silver)
2-665-774-01
1.4
2.5
1.7
4.0
4.0
#45: M1.4 X 2.5
(Silver)
2-587-151-01
#44: M1.7 X 3.0 (Tapping)
(Silver)
3-078-890-61
#51: M2.0 X 2.5
(Silver)
3-073-686-01
#52: M2.0 X 4.0 (Tapping)
(Black)
3-080-206-11
2.0
2.0
2.0
4.0
3.0
2.5
#53: M2.0 X 5.0 (Tapping)
(Black)
3-080-206-21
6.0
5.0
#57: M1.7 X 4.0
(Black)
7-627-852-18
#56: M2.0 X 3.5
(Silver)
3-067-187-11
1.75
2.0
2.0
4.0
#58: M2.0 X 6.0 (Tapping)
(Silver)
3-719-408-11
6.0
2.0
3.5
#59: M2.0 X 5.0 (Tapping)
(Silver)
3-080-205-21
2.0
1.7
4.0
#55: M2.0 X 4.0
(Silver)
2-655-582-11
#54: M1.75 X 6.0 (Tapping)
(Black)
3-318-203-11
#60: M2.6 X 5.0
(Black)
3-061-062-11
2.6
2.0
5.0
5.0
HARDWARE LIST (4/4)
#61: M3.0 X 10.0
(Black)
7-682-549-09
#62: M2.0 X 3.0
(Silver)
3-080-202-21
3.0
10.0
2.0
12.5
#66: M1.4 X 1.4
(Silver)
2-635-591-41
1.4
3.5
#69: M1.7 X 3.0
(Silver)
2-599-475-21
#77: M1.2 X 5.0 (Tapping)
(Silver)
3-086-156-31
1.2
#72: M1.4 X 2.0
(Silver)
4-663-621-41
1.4
1.4
2.0
2.0
#75: M1.7 X 3.5 (Tapping)
(Silver)
2-666-551-01
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
1.7
1.7
6.0
1.7
4.0
#71: M1.4 X 2.0
(Red)
3-208-537-01
#74: M1.7 X 6.0 (Tapping)
(Silver)
2-666-551-31
1.2
5.0
2.0
5.0
4.0
1.4
1.7
1.7
#73: M1.2 X 4.0 (Tapping)
(Black)
3-086-156-61
#68: M1.7 X 4.0
(Silver)
2-655-581-01
1.4
#70: M1.7 X 5.0
(Silver)
2-599-475-41
3.0
5.0
#67: M1.4 X 2.0
(Silver)
3-389-523-16
1.4
1.7
5.0
3.0
#65: M1.4 X 3.5
(Silver)
2-635-591-01
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
#63: M5.0 X 12.5
(Black)
3-060-811-21
3.5
1.7
4.0
Reverse
985221033.pdf
Revision History
History
Date
1.0
2007.06
Official Release
1.1
2007.07
Revised-1
• Correction of Schematic Diagrams
• Addition of CMOS Imager’s Note
• Correction of Accessories
S.M. correction:Page 4-37, Page 4-38,
Page 5-10, Page 5-27,
Page 5-28
Yes
1.2
2007.11
Supplement-1
(S1 DI07-196)
• Addition of Attention Sentence of HELP
• Change of Repair Parts
• Revision of Accessories
S.M. revised: Page 5-26, Page 5-27,
Page 5-28
Yes
HDR-CX6EK/CX7/CX7E/CX7K/CX7EK_L2
Contents
S.M. Rev.
issued
—
Ver.
—