Download 取扱説明書 - Oriental Motor
Transcript
HF-3112-3 取扱説明書 ブラシレス DC ファン MDS シリーズ MD シリーズ お買い上げいただきありがとうございます。 この取扱説明書には、製品の取り扱いかたや安全上の注意事項を示 しています。 ・取扱説明書をよくお読みになり、製品を安全にお使いください。 ・お読みになったあとは、いつでも見られるところに必ず保管して ください。 ●ファンは筐体内に設置してください。 けがの原因になります。 ●電源入力電圧は、定格範囲を必ず守ってください。火災の 原因になります。 はじめに ●接続は接続図にもとづき、確実に行なってください。火災 ■お使いになる前に の原因になります。 製品の取り扱いは、 適切な資格を有する人が行なってください。 ●ケーブルを無理に曲げたり、引っ張ったり、はさみ込んだ お使いになる前に、 「安全上のご注意」をよくお読みのうえ、 りしないでください。火災の原因になります。 正しくお使いください。 ●電源には、 一次側と二次側が強化絶縁された直流電源を使 この製品は、 一般的な産業機器の機器組み込み用として設計 用してください。感電の原因になります。 されています。その他の用途には使用しないでください。ま ●停電したときは、電源を切ってください。停電復旧時に た、電源には、一次側と二次側が強化絶縁された直流電源を ファンが突然起動して、 けが・装置破損の原因になります。 使用してください。 この警告を無視した結果生じた損害の補 ●ファンを分解・改造しないでください。 けがの原因になり 償については、当社は一切その責任を負いませんので、あら ます。内部の点検や修理は、お買い上げになった支店また かじめご了承ください。 は営業所に連絡してください。 For English version, see opposite side. ■規格・CE マーキング この製品は、UL 規格、CSA 規格の認定を取得し、EN 規格に 注意 もとづいて CE マーキング(EMC 指令)を実施しています。 ●ファンの仕様値を超えて使用しないでください。けが・装 ◆認定規格 置破損の原因になります。 ●ファンの開口部に指や物を入れないでください。 けがの原 認定機関 規格ファイル No. 認定規格 因になります。 UL 507 E58377 UL ●ファンの回転部(羽根) 、リード線を持たないでください。 CSA C22.2 No.113 けがの原因になります。 ◆設置条件(EN/IEC 規格) ●ファンの周囲には、可燃物を置かないでください。火災・ 過電圧カテゴリーⅠ、汚染度 2、クラスⅢ機器 やけどの原因になります。 ◆適合規格 ●ファンの周囲には、 通風を妨げる障害物を置かないでくだ EMI EN 55011 グループ 1、クラス A さい。装置破損の原因になります。 EMS EN 61000-6-2 ●ファンを設置するときは、 静電対策を行なってから設置し てください。装置破損の原因になります。 ◆有害物質 ●運転中は回転部(羽根)に触れないでください。けがの原 RoHS(EU 指令 2002/95/EC 27Jan.2003)適合 因になります。保護のため、オプションのフィンガーガー ドを使用してください。 安全上のご注意 ●異常が発生したときは、ただちに運転を停止して、電源を ここに示した注意事項は、製品を安全に正しくお使いいた 切ってください。火災・けがの原因になります。 だき、お客様や他の人々への危害や損傷を未然に防止する ●ファンを廃棄するときは、 できるだけ分解し、産業廃棄物 ためのものです。内容をよく理解してから製品をお使いく として処理してください。 ださい。 警告 この警告事項に反した取り扱いをすると、死亡または重傷 を負う場合がある内容を示しています。 注意 この注意事項に反した取り扱いをすると、傷害を負うまた は物的損害が発生する場合がある内容を示しています。 重要 製品を正しくお使いいただくために、お客様に必ず守って いただきたい事項を本文中の関連する取り扱い項目に記載 しています。 準備 ■製品の確認 パッケージを開けたら、次のものがすべて揃っているか、 確認してください。不足している場合や破損している場合 は、お買い求めの支店・営業所までご連絡ください。 セット品の付属品については、添付の「パッケージ内容一 覧」をご覧ください。 ・ファン ................................. 1 台 ・コネクタ付ケーブル ......... 1 本 ・取扱説明書 ......................... 1 部 ◆パルスセンサタイプ MDS1751-24SH、MDS1451-24SH、MDS1451-48SH、 ●爆発性雰囲気、引火性ガスの雰囲気、腐食性の雰囲気、水 MD925A-12SH、 MD925A-24SH、 MD825B-12SH、 のかかる場所、可燃物のそばでは使用しないでください。 MD825B-24SH、 MD625B-12SH、 MD625B-24SH 火災・けがの原因になります。 ◆回転停止アラーム 無接点タイプ ●設置、接続、運転・操作、点検・故障診断の作業は、適切 MDS1451-24LH、 MDS1451-48LH、 MD925A-12LH、 な資格を有する人が行なってください。火災・けがの原因 MD925A-24LH、 MD825B-12LH、 MD825B-24LH、 になります。 MD625B-12LH、 MD625B-24LH、 MDS510-12LH、 ●拘束保護回路がはたらいたときは、 電源を切ってください。 MDS510-24LH、 MDS410-12LH、 MDS410-24LH 拘束状態が解除されたときにファンが突然起動して、け が・装置破損の原因になります。 警告 ◆回転低下アラーム 無接点タイプ MDS1225-12MH、MDS1225-24MH ◆回転低下アラーム 有接点タイプ MDS1751-24BH ◆標準タイプ MDS1751-24H、 MDS1451-24H、 MDS1225-12H、 MDS1225-24H、 MD1225-24H、 MD925A-12H、 MD825B-12H、 MD825B-24H、 MD625B-24H、 MDS510-12H、 MDS510M-5H、 MDS410-12H、 MDS410M-5H ■回転停止アラーム 無接点タイプ MDS1451-48H、 MD1225-12H、 MD925A-24H、 MD625B-12H、 MDS510-24H、 MDS410-24H、 㤛 㤥 φ I 5 mAએਅ GND 䊐䉜䊮 Vc䋺DC30 V R એਅ 0V 䈍ቴ᭽䈱࿁〝 重要 回転停止アラーム回路には遅延機能がありません。ファンが起動 するときなど検出を回避する場合は、外部に遅延機能が必要です。 遅延時間は 1 秒以上としてください。 ■回転低下アラーム 無接点タイプ 設置 ■設置場所 ファンは機器組み込み用に設計、製造されています。 風通しがよく、点検が容易な次のような場所に設置してください。 ・屋内に設置された筐体内(換気口を設けてください) ・使用周囲温度 -10 ∼ +60 ℃(凍結しないこと) ・使用周囲湿度 85%以下(結露しないこと) ・爆発性雰囲気、有害なガス(硫化ガスなど) 、および液体 のないところ ・直射日光が当たらないところ ・塵埃や鉄粉などの少ないところ ・水(雨や水滴)、油(油滴) 、およびその他の液体がかか らないところ ・塩分の少ないところ ・連続的な振動や過度の衝撃が加わらないところ ・電磁ノイズ(溶接機、動力機器など)が少ないところ ・放射性物質や磁場がなく、真空でないところ ■設置方法 ファンは耐振動性にすぐれ、熱伝導効果が高い平滑な金属 板に設置してください。カタログの取付穴参考寸法図をも とに、使用する機器に取付穴をあけて、ファンをねじ(付 属していません)で固定してください。風の方向、回転方 向は、総合カタログの外形図を参照してください。 品名 ねじサイズ 締付トルク MDS1751タイプ、MDS1451タイプ、 MDS1225タイプ、MD1225タイプ、 MD925Aタイプ、 MD825Bタイプ MD625Bタイプ、MDS510タイプ、 MDS410タイプ 黄色がアラームのリード線 です。GND は共通です。 図のようにお客様の回路に 接続してください。 通電中にファンの回転が 停止すると、アラーム信号 (H レベル)を出力します。 M4 0.6 N·m M3 0.4 N·m ■コネクタハウジング/コンタクト メーカー:日本圧着端子製造株式会社 ハウジング品番:SMR-03V-N(3 極) 、SMR-04V-N(4 極) コンタクト品番:SYM-001T-P0.6 電源の接続 赤のリード線を電源の+(プラス) 側に、黒のリード線を GND 側に、 それぞれ接続してください。 製品の銘板で電圧仕様を確認し、 正しい電圧を入力してください。 ⿒ 㤥 DC㔚Ḯ 㧗 GND 橙と青がアラームのリー ド線です。図のようにお 客様の回路に接続してく ださい。 ファンの回転速度が 2100±400 r/min 以下に低 䊐䉜䊮 下すると、アラーム信号 (H レベル)を出力します。 ᯍ 㕍 I φ 15 mAએਅ Vc䋺DC30 V R એਅ 0V GND 䈍ቴ᭽䈱࿁〝 ■回転低下アラーム 有接点タイプ 橙と青がアラームのリー ド線です。図のようにお 客様の回路に接続してく ださい。 ファンの回転速度が 1800±400 r/min 以下に低 䊐䉜䊮 下すると、アラーム信号 (H レベル)を出力します。 ᯍ 㕍 I φ 30 mAએਅ Vc䋺DC30 V R એਅ 0V 䈍ቴ᭽䈱࿁〝 重要 起動遅延回路を内蔵しています。ファンが起動した後 10 秒以内に アラーム機能が有効になります。 拘束時の焼損保護 焼損防止回路を内蔵しています。拘束状態を検知すると、 自動的に巻線に流れる電流を制御します。羽根が拘束され て焼損することはありません。 拘束状態が解除されると自動的に運転を再開します。点検 するときは、必ず電源を切ってください。 ・ この取扱説明書の一部または全部を無断で転載、複製すること は、禁止されています。 ・ 製品の性能、仕様および外観は改良のため予告なく変更するこ とがありますのでご了承ください。 ・ 取扱説明書には正確な情報を記載するよう努めていますが、 万一ご不審な点や誤り、記載もれなどにお気づきの点がありま したら、最寄りのお客様ご相談センターまでご連絡ください。 ・ は、 オリエンタルモーター株式会社の商標 です。 は、 日本その他の国で登録されたオリエンタルモーター 株式会社の商標です。 Copyright ORIENTAL MOTOR CO., LTD. 2006 http://www.orientalmotor.co.jp/ アラームとセンサの接続と仕様 ■パルスセンサタイプ 䃂㩷ຠ䈮䈧䈇䈩䈱䈗⾰䇮䈗⋧⺣䈲䈍ቴ᭽䈗⋧⺣䉶䊮䉺䊷䈻䈍䈇ว䉒䈞䈒䈣䈘䈇䇯 㩷 䊐䊥䊷䉮䊷䊦䋨ήᢱ䋩䈪䈜䇯៤Ꮺ㔚䊶PHS䈎䉌䉅䈗↪䈏น⢻䈪䈜䇯 Vc䋺DC30 V 黄色がパルス出力のリード R એਅ 㤛 φ I 線です。GND は共通です。 5 mAએਅ㪁 㤥 図のようにお客様の回路に 0V GND 接続してください。 䈍ቴ᭽䈱࿁〝 パルス出力は、1 回転あたり 䊐䉜䊮 2周期の矩形波を出力します。㪁㩷MDS1751-24SH䈱䉂㪈㪇㩷㫄㪘એਅ 㩷 ฃઃᤨ㑆㩷 ᐔᣣ㩷 㩷 㩷 ᦐᣣ㩷 9:00䌾18:30 9:00䌾17:30 ᧲㩷 ੩㩷 TEL 0120-925-410 ฬฎደ㩷 TEL 0120-925-420 ᄢ㩷 㒋㩷 TEL 0120-925-430 FAX 0120-925-601 FAX 0120-925-602 FAX 0120-925-603 䈖䈱ขᛒ⺑ᦠ䈲ౣ↢⚕䉕↪䈚䈩䈇䉁䈜䇯 HF-3112-3 OPERATING MANUAL Brushless DC Fan MDS Series MD Series Introduction Before using the fan Only qualified personnel should work with the product. Use the product correctly after thoroughly reading the section “Safety precautions.” The product described in this manual has been designed and manufactured for use in general industrial machinery, and must not be used for any other purpose. For the power supply use a DC power supply with reinforced insulation on its primary and secondary sides. Oriental Motor Co., Ltd. is not responsible for any damage caused through failure to observe this warning. Standard • CE marking This product is recognized by UL and certified by CSA, and bears the CE Marking (EMC Directives) in compliance with the EN Standards. Standards Standards Certification body Standards File No. UL 507 UL E58377 CSA C22.2 No.113 Installation conditions (For EN/IEC standards) Overvoltage category I, Pollution degree 2, Class III equipment Applicable standards EMI EN 55011 Group 1, Class A EMS EN 61000-6-2 Hazardous substances RoHS (Directive 2002/95/EC 27Jan.2003) compliant Safety precautions The precautions described below are intended to prevent danger or injury to the user and other personnel through safe, correct use of the product. Use the product only after carefully reading and fully understanding these instructions. Warning Caution Note Handling the product without observing the instructions that accompany a “Warning” symbol may result in serious injury or death. Handling the product without observing the instructions that accompany a “Caution” symbol may result in injury or property damage. The items under this heading contain important handling instructions that the user should observe to ensure safe use of the product. Warning • Do not use the product in explosive or corrosive environments, in the presence of flammable gases,locations subjected to splashing water, or near combustibles. Doing so may result in fire or injury. • Assign qualified personnel the task of installing, wiring, operating/controlling, inspecting and troubleshooting the product. Failure to do so may result in fire or injury. • Shut off the power to the fan in the event the lock-protection circuit is activated. Otherwise, the fan will start unexpectedly when released from the locked condition, causing bodily injury or equipment damage. • Install the fan in an enclosure in order to prevent injury. • Keep the input-power voltage within the specified range to avoid fire. Thank you for purchasing an Oriental Motor product. This Operating Manual describes product handling procedures and safety precautions. • Please read it thoroughly to ensure safe operation. • Always keep the manual where it is readily available. • Connect the cables securely according to the wiring diagram in order to prevent fire. • Do not forcibly bend, pull or pinch the cable. Doing so may fire. • For the power supply use a DC power supply with reinforced insulation on its primary and secondary sides. Failure to do so may result in electric shock. • Turn off the power in the event of a power failure, or the fan will suddenly start when the power is restored and may cause injury or damage to equipment. • Do not disassemble or modify the fan. This may cause injury. Refer all such internal inspections and repairs to the branch or sales office from which you purchased the product. Caution • Do not use the fan beyond its specifications, or injury or damage to equipment may result. • Keep your fingers and objects out of the openings in the fan. This may cause injury. • Do not hold the rotating parts (blades) of the fan or lead wire. This may cause injury. • Keep the area around the fan free of combustible materials in order to prevent fire or a burn. • To prevent the risk of damage to equipment, leave nothing around the fan that would obstruct ventilation. • Provide anti-static measures before installing the fan. Failure to do so may result in equipment damage. • Do not touch the rotating parts (blades) when the fan is in operation. This may cause injury. The use of the optional fingerguard is recommended to ensure protection. Wegen der Verletzungsgefahr dürfen die Lüfterflügel bei Ventilatorbetrieb nicht berührt werden. Der Gebrauch des als Sonderzubehör erhältlichen Fingerschutzes ist empfehlenswert, um erhöhte Sicherheit zu ewährleisten. • Immediately when trouble has occurred, stop running and turn off the power. Failure to do so may result in fire, electric shock or injury. • To dispose of the fan, disassemble it into parts and components as much as possible and dispose of individual parts/components as industrial waste. Preparation Checking the product Upon opening the package, verify that the items listed below are included. Report any missing or damaged items to the branch or sales office from which you purchased the product. For the supplied items in the fan set, refer to the separate “Package item list.” • Fan ..................................... 1 pc. • Cable with connector ......... 1 pc. • Operating manual .............. 1 copy Pulse sensor type MDS1751-24SH, MDS1451-24SH, MDS1451-48SH, MD925A-12SH, MD925A-24SH, MD825B-12SH, MD825B-24SH, MD625B-12SH, MD625B-24SH Stall alarm, electronic alarm type MDS1451-24LH, MDS1451-48LH, MD925A-12LH, MD925A-24LH, MD825B-12LH, MD825B-24LH, MD625B-12LH, MD625B-24LH, MDS510-12LH, MDS510-24LH, MDS410-12LH, MDS410-24LH Low-speed alarm, electronic alarm type MDS1225-12MH, MDS1225-24MH Low-speed alarm, contact alarm type MDS1751-24BH Standard type MDS1751-24H, MDS1225-12H, MD1225-24H, MD825B-12H, MD625B-24H, MDS510M-5H, MDS410M-5H MDS1451-24H, MDS1225-24H, MD925A-12H, MD825B-24H, MDS510-12H, MDS410-12H, MDS1451-48H, MD1225-12H, MD925A-24H, MD625B-12H, MDS510-24H, MDS410-24H, Installation Location for installation The fan is designed and manufactured for installation in equipment. Install it in a well-ventilated location that provides easy access for inspection. The location must also satisfy the following conditions: • Inside an enclosure that is installed indoors (provide vent holes) • Operating ambient temperature -10 to +60 °C (+14 to +140 °F) (non-freezing) • Operating ambient humidity 85%, maximum (non-condensing) • Area that is free of explosive atmosphere or toxic gas (such as sulfuric gas) or liquid • Area not exposed to direct sun • Area free of excessive amount of dust, iron particles or the like • Area not subject to splashing water (rains, water droplets), oil (oil droplets) or other liquids • Area free of excessive salt • Area not subject to continuous vibration or excessive shocks • Area free of excessive electromagnetic noise (from welders, power machinery, etc.) • Area free of radioactive materials, magnetic fields or vacuum How to install the fan Install the fan onto an appropriate flat metal plate having excellent vibration resistance and heat conductivity. See the panel cut-out, mounting-hall reference drawing for information on how to provide mounting holes on the equipment used and secure the fan with screws (not supplied). For air orientation and rotational direction, see the outline drawings in the catalogue. Model Screw size MDS1751 type, MDS1451 type, MDS1225 type, MD1225 type, M4 MD925A type, MD825B type MD625B type, MDS510 type, M3 MDS410 type Tightening torque 0.6 N·m (5.3 lb-in) 0.4 N·m (3.5 lb-in) Connector housings/Contacts Manufacturer: J.S.T. Mfg Co., Ltd. Housings model: SMR-03V-N (3 poles), SMR-04V-N (4 poles) Contacts model: SYM-001T-P0.6 Connecting the power supply Connect the red wire to the positive (+) power supply and the black wire to the ground connection. DC power supply Red + Black GND Check the voltage specification on the product identification plate and input the correct voltage. The orange and blue Vc: 30 VDC wires are lead wires for or less R the alarm circuit. Orange I Connect these wires to 15 mA or less Blue the client’s as shown in the figure below. 0V GND An alarm (H level) signal Client's circuit Fan is output when the fan’s rotation speed falls below 2100±400 r/min. Low-speed alarm, contact alarm type The orange and blue wires Vc: 30 VDC are lead wires for the alarm or less R circuit. Connect these Orange I wires to the client’s circuit 30 mA or less Blue as shown in the figure. 0V An alarm (H level) signal Client's circuit Fan is output when the fan’s rotation speed falls below 1800±400 r/min. Note The low-speed alarm type of fan is equipped with an internal delayed-start alarm circuit. The alarm function becomes effective within 10 seconds of the fan start. Overheat protection The fan is equipped with an internal protective circuit against overheating. In the event a lock-up condition is detected, this function automatically controls the current flow to the fan motor’s windings, thus preventing the fan blades from locking and burning out. The fan resumes operation automatically as soon as it is released from the locked condition. Be sure to shut off the power to the fan before performing an inspection. • Unauthorized reproduction or copying of all or part of this Operating Manual is prohibited. • Characteristics, specifications and dimensions are subject to change without notice. • While we make every effort to offer accurate information in the manual, we welcome your input. Should you find unclear descriptions, errors or omissions, please contact the nearest office. • is a trademark of Oriental Motor Co., Ltd. is a trademark of Oriental Motor Co., Ltd., and is registered in Japan and other countries. • Please contact your nearest Oriental Motor office for further information. Vc: 30 VDC The yellow wire is lead wire R or less Yellow I for the pulse output. GND is common to the sensor and 5 mA or less∗ Black power supply. Connect these GND wires to the client’s circuit as 0V shown in the figure below. Fan Client's circuit Two cycles of rectangular waves are output per rotation. ∗ MDS1751-24SH = 10 mA or less Stall alarm, electronic alarm type The yellow wire is lead wire for the alarm circut. GND is common to the sensor and power supply. Connect these wires to the client’s circuit as shown in the figure below. If the fan stalls while the power is on, an alarm signal (H level) is output. Low-speed alarm, electronic alarm type Copyright ORIENTAL MOTOR CO., LTD. 2006 Connection and specifications of the alarm/sensor Pulse sensor type Note The stall alarm type of fan is not equipped with a delayed trippoint alarm circuit. Therefore, an external delay function is necessary to avoid the detection of fan start. The set time of the delay function should be at least one second. ORIENTAL MOTOR U.S.A. CORP. Technical Support Line Tel:(800)468-3982 Available from 7:30 AM to 5:00 PM, P.S.T. E-mail: [email protected] www.orientalmotor.com ORIENTAL MOTOR (EUROPA) GmbH Headquarters and Düsseldorf Office Munich Office Hamburg Office Tel:0211-5206700 Fax:0211-52067099 Tel:08131-59880 Fax:08131-598888 Tel:040-76910443 Fax:040-76910445 ORIENTAL MOTOR (UK) LTD. ORIENTAL MOTOR (FRANCE) SARL Tel:01256-347090 Fax:01256-347099 Tel:01 47 86 97 50 Fax:01 47 82 45 16 ORIENTAL MOTOR ITALIA s.r.l. TAIWAN ORIENTAL MOTOR CO., LTD. Tel:02-93906346 Fax:02-93906348 Tel:(02)8228-0707 Fax:(02)8228-0708 SINGAPORE ORIENTAL MOTOR PTE. LTD. Tel:(6745)7344 Fax:(6745)9405 Yellow I 5 mA or less Black GND Fan Vc: 30 VDC or less R 0V Client's circuit ORIENTAL MOTOR (MALAYSIA) SDN. BHD. Tel:(03)79545778 Fax:(03)79541528 INA ORIENTAL MOTOR CO., LTD. KOREA Tel:(032)822-2042~3 Fax:(032)819-8745 ORIENTAL MOTOR CO., LTD. Headquarters Tokyo, Japan Tel:(03)3835-0684 Fax:(03)3835-1890 Printed on Recycled Paper