Download Service Manual K1 CHASSIS

Service Manual
K1 CHASSIS
CONTENTS
o
o
o
o
o
o
o
o
o
o
o
o
PAGE
Safety Instructions
Technical Specifications
Remote Control
Preparations
Operating Your TV
Block Diagram
IC Datasheets&Specs
Pin Voltages of IC’s
Oscillosgraphs Of Some IC Pins
Electrical Adjustments
Channel Frequency Tables
Spare Part List
1
2
3
4
5
6
10
11
18
20
24
29
31
1. SAFETY INSTRUCTIONS
GENERAL GUIDELINES
1. It is advised to insert an isolation transformer
in the AC supply before servicing a hot
chassis.
.
exposed metallic part a return path to the
chassis the reading should be between
4Mohm and the 20Mohm. When the exposed
metal does not have a return path to the
chassis, the reading must be infinite.
2. Potentials as high as 33KV are present when
this receiver is in operation. Operation of the
receiver without the rear cover involves the
danger of a shock hazard from the receiver
power supply. Servicing should not be
attempted by any one who is not competent
with the precautions necessary when working
on the high voltage equipment. Always
discharge the anode of the tube.
LEAKAGE CURRENT HOT CHECK
1. Plug the AC cord directly in to the AC outlet.
Do not use an isolation transformer for this
check.
2. Connect a 2Kohm 10W resistor in series with
an exposed metallic part on the receiver and
an earth, such as a water pipe.
3. Use an AC voltmeter with high impedance to
measure the potential across the resistor.
4. Check each exposed metallic part and
check the voltage at the each point.
5. Reverse the AC plug at the outlet and repeat
each of the above measurements.
6. The potential at the any point should not
exceed 1.4 Vrms. In case a measurement is
outside the limits specified, there is the
possibility of a shock hazard, and the receiver
should be repaired and rechecked before it
is returned to the customer.
3. When servicing observe the original lead
dress in the high voltage circuits. If a short
circuit is found, replace all the parts which
have been overheated or damaged by the
short circuit.
4. Always use the manufacturer’s replacement
safety components. The critical safety
on the
components marked with
schematics diagrams should not be replaced
by other substitutes. Other substitute may
create the electrical shock, fire or other
hazards. Take attention to replace the
spacers with the originals. Furthermore where
a short circuit has occurred, replace those
components that indicate evidence of
overheating.
HOT CHECK CIRCUIT
AC-Voltmeter
TO INSTRUMENTS
EXPOSED
Water pipe
(earth)
METALLIC PARTS
5. After servicing, see that all the protective
devices such as insulation barriers, insulation
papers,
shields
and
isolation
R-C
combinations are correctly installed.
2 K Ohm
6. When the receiver is not being used for a
long time of period of time, unplug the
power cord from the AC outlet.
Figure 1
X-RAY RADIATION WARNING
The primary source of X-ray radiation in this receiver
is the picture tube. The chassis is specially
constructed to limit X-ray radiation. For continued Xray radiation protection, replace the tube with the
same type of the original one.
7. After servicing make the following leakage
current checks to prevent the customer from
being exposed to shock hazard.
LEAKAGE CURRENT COLD CHECK
1. Unplug the AC cord and connect a jumper
between the two prongs of the plug.
CAUTION
AFTER REMOVAL OF THE ANODE CAP, DISCHARGE THE
ANODE OF THE PICTURE TUBE AND THE ANODE CAP TO
THE METAL CHASSIS, CRT SHIELD, OR THE CARBON
PAINTED ON THE CRT WITH A HIGH VOLTAGE PROBE
AND MULTIMETER (SELECT VDC) AND THEN SHORT
CIRCUIT DIRECTLY TO DISCHARGE COMPLETELY
2. Turn the receiver’s power switch on.
3. Measure the resistance value with an
ohmmeter, between the jumpered AC plug
and each exposed metallic cabinet part on
the receiver, such as screw heads, aerials,
connectors, control shafts etc. When the
2
2.
TECHNICAL SPECIFICATIONS
.
Power source:
220-240V AC, 50-60Hz
Power consumption (nom.) :
55W
Standby power consumption :
2W
Aerial impedance :
75Ohm, coaxial type
Receiving system 1:
PAL BG
PAL SECAM BG
PAL SECAM BG DK
PAL I
Receiving channels:
VHF BAND I
VHF BAND III
CABLE TV
UHF BAND
Audio outputs :
7W RMS at %10 THD
High Voltage :
25 ± 0.5 KV
Focus voltage :
%25.6 ± %38 of EHT
Grid 2 voltage :
0-1400 V
Heater voltage :
6.2 ± 0.2 Vrms
Video/Audio Terminals :
AV1 IN
20”, 21”
CH2-4
CH5-12
S1-41
CH21-69
20”, 21”
20”, 21”
AV1OUT
AV2 IN (RCA, optional)
Operating temperature :
0-45 Degrees
Safety :
IEC 65 /BS P2N
X-Ray radiation :
ACC. IEC 65/BS P2N
1
Video : 1 Vpp,75 Ohm
Audio : 0.5 Vrms, >10 Kohm
RGB
Video : 1 Vpp, 75 Ohm
Audio : 0.5 Vrms, <1 Kohm
Video : 1 Vpp, 75 Ohm
Audio : 0.5 Vrms, >10 Kohm
: TV set is produced to receive “one” of these colour and sound systems.
3
3. REMOTE CONTROL
.
Special features
• Your TV can receive stereo channels directly(NICAM optional).
• Automatic tuning system with country selection.
• 100 Programme Memory
• Available for Cable Channels (A decoder maybe required)
• Manual Fine Tuning
• Child Lock
• Return to the last channel viewed (SWAP)
• Spatial Sound effect
• 16:9 picture format
• S-Video connection (optional)
• Audio/Video RCA sockets (optional).
• Normalisation system to recall the setting in memory after the
colour,contrast, brightness setting have been changed.
• Picture adjustment using one button (Smart control).
• Sound adjustment using one button (Smart control).
• Equalizer Sound Setup
• Automatic Volume Limiting
• Your TV set is equipped with an On-Screen Display system.
This system enables the user to see the function on-screen and
to control them efficiently.
• Infrared Remote Control
• Virtual Dolby Surround (optional)
• Dynamic Bass (optional)
• Multi language menu system
• On Timer
• Off Timer
• Stereo headphone socket (optional)
• Scart Socket: Video cassette recorder, satellite receiver, video
disc player,DVD, TV games or a home computer can be
connected to this AV socket with an appropriate connecting
cable.
• Second scart socket (optional)
• Naming the channels
• Teletext reception
• Auto recognition of the broadcasting format (4:3, 16-9) via
WSS feature.
• Digital Colour Transition Improvement (DCTI) (Optional).
• Digital Comb Filter (DCF) (Optional).
• Digital Luminance Transition Improvement (DLTI) (Optional)
• Dynamic Noise Reduction (Optional)
• Picture and Text (optional)
• Blueback (Optional)
• Component input via Scart (optional)
• Program Naming, Editing
• Quick Program Display
• Games (Optional)
• Now&Next (TV Guide), (Optional)
• Alarm function (Optional)
(*): These features are not available in all models.
4
4. PREPARATIONS
.
MAIN SUPPLY CONNECTIONS
Connect the TV mains plug into your domestic mains
socket outlet (230 V 50Hz AC).
Press the Program up, Program down button or
Numeric Buttons on the remote handset to switch
• the TV on.
AERIAL CONNECTION
Using a 75Ω aerial lead connect your TV to the
aerial outlet in your home.
BATTERY FITTING
Insert the 2 AAA Batteries supplied into the
compartment on the rear of the remote control,
ensure you follow the polarity diagram inside
the compartment.
4
4
PIN CONNECTIONS FOR SCART SOCKET
1- Audio output Right
11- RGB input, Green
2- Audio input Right
123- Audio output Left(Mono)13- Red ground
4- Audio ground
14- Ground
5- Blue ground
15- RGB input, Red
6- Audio input Left(Mono) 16- Blanking Signal
7- RGB input, Blue
17- Video output ground
8- Switching voltage
18- Video input ground
9- Green ground
19- Video output
1020- Video input
21- Screening
CONNECTING TV WITH VIDEO AND SATELLITE/DIGITALRECEIVER
5
.
5. OPERATING YOUR TV
C. TUNING THE TELEVISION
A. SWAP FUNCTION
There are two ways of tuning your television:
• Manual, where you control the tuning process
or Autoprogram where the television does it all
automatically.
• The TV sets equipped with ATS (Automatic
Tuning System) sorts the channels regarding
the broadcasting system of your country
(optionally).
Allows you to swap between the
program you are watching and the
last selected program. i.e. If you were
watching Program 1 and
change to Program 11, press the
SWAP button to go back to
Program 1. Press it again to return to
Program 11.
Please Note
If the TV is set to a channel with no signal the
TV will return to standby after 5 minutes. The
time remaining is displayed on the screen.
Manual Tuning
Tuning the TV is accessed through the SETUP
menu.
There are two ways to access the SETUP
menu:
B. AV
Press theAV button to select your
For use when you are connecting an
external source to your TV (Video
recorder, DVD player etc.) via the SCART
sockets or RCA sockets.
Press the blue Setup button or Press
the Menu button and use the
Program down button to select
SETUP. Press the OK button to
enter the SETUP menu.
See ‘Connecting external equipment’.
Press the AV button to select your input as
follows:
2 Scart models:
1 AV1 when using SCART socket 1.
2 AV2 when using SCART socket 2.
3 AV2-S for S-Video equipment. (Optional)
4 AV3 when using the RCA sockets
of the TV. (Optional)
5 AV3-S when using the S-video socket and
RCA audio sockets of the TV. (Optional)
1 Scart models:
1 AV1 when using SCART socket 1.
2 AV2 when using the RCA sockets of the
TV. (Optional)
3 AV2-S when using the S-video socket and
RCA audio sockets of the TV. (Optional)
Please note
The system will displayed automatically on
SYSTEM row i.e.BG, L, I, DK depending the
receiving broadcasting system of the country. In
some countries the broadcasting system can be
both in BG/DK or BG/LL´. Only the TV sets
produced with Pal Secam BG/DK or Pal Secam
BG/LL´ systems can receive both BG/DK or
BG/LL´ broadcasts. In this case the user can
select the required SYSTEM using Volume
up/down buttons.
Press the AVbutton again to return
toTV
6
Please note
If you do not press any buttons for 15
seconds the TV will exit the menu
system.
Tuning with channel numbers
Enter the SETUP menu by pressing
the blue button. Press the OK button
to enter the CHANNEL row.
In the Setup menu select PROG NO
and change to P1 using the Program
down button to select it and the
Volume up button to change it.
Use the OK button to select “S” for
cable channels and “C” for terrestrial
broadcast.
Use Volume up button to select the
channel number buttons.
Starting with Program 1, tune in the
first channel as follows:
Enter the channel number using the
Numeric buttons.
Use the Program down button to
select SEARCH.
Press the Program down/up buttons
to exit the channel row.
Press the Volume up or Volume
down button to start the tuning
search.
Use the Program down button to
select PROGRAM NO.
Use the Volume up/down buttons to
select the program number.
When the search finds a strong
channel signal it will stop searching.
The picture will appear.
Use the Program down button to
select STORE. Press the OK button
and STORED will appear on the
STORE line.
Identify which channel you are
watching (BBC 1, ITV 1 etc.) and
decide which program number you
want it to be.
You have now stored the first
channel.
Use the Program down button to
select PROGRAM NO.
Use the Program up button to select
again SEARCH and continue the
tuning procedure until you have tuned
in all the programmes you want or the
television can receive.
To exit the SETUP menu press the
TV/TX button.
Use the Volume up/down buttons to
select the program number.
Use the Program down button to
select Store. Press theOK button and
STORED will appear on the STORE
line.
Automatic tuning (Autoprogram)
Enter the SETUP menu as before.
You have now stored the first
channel.
Use the Program up button to select
again SEARCH and continue the
tuning procedure until you have tuned
in all the programmes you want or the
television can receive.
7
Use the Program down button to
select AUTOPROGRAM and the OK
button. A list of Press countries will
appear. Select the desired country
using Program and Volume buttons.
Note: TV Guide information may not have for all
programmes. It depends on the broadcasting
and determined by broadcasting company.
Note: TV Guide is not displayed on the screen,
if there is not a provider in the saved channels.
When you are sure the aerial is
connected properly press the OK
button. Autoprogam will start.
To cancel Autoprogram while
isworking press the Menu button.
it
Your TV is now tuned and ready to use.
DATE: Date information is given by provider
channel. You can use the numeric buttons to
change the date.
Please note:
If auto sort fails to arrange the programmes in
the required sequence please refer to
programme table.
PROVIDER: Provider is the channel which send
the TV Guide information. You can select the
provider via this function. Press Volume
up/down buttons to select the provider and
then press "OK".
Fine tuning
Although the search and Autoprogram will
automatically try and tune to the best reception,
in areas of poor reception a bit of fine tuning
may be required.
In the SETUP menu use the Program
up/down buttons to select FINE
TUNE. Use the Volume up and
Volume down buttons to fine tune.
When you have finished use the
Program down button to select
STORE and press the OK button.
.
STATION MATCH: The supported channels by
provider may not be defined automatically. You
can open this menu and define the provider for
these channels. Adjusting the provider just one
time is enough for these channels.
D. FEATURES
1-) TV GUIDE(Optional)
You can see the TV Guide information on the
screen by pressing "DOUB" button while a
provider channel or a supported channel by
provider is selected. The information of the
current and next programmes which is sent by
provider is displayed on the screen.
8
DISPLAY INFO: If you want to see the TV
Guide information automatically while changing
the channels, this option should be open. In this
case, if you open the provider channel Mini
Guide occurs on the screen.
2-) PAT (Picture and Text) (OPTIONAL)
In the double window function, you can also
display the teletext screen in the second
window.
3-) PIP Picture Position Change
Press the POS button repeatedly until
desired position is achieved. The PIP
picture moves clockwise.
9
.
6. BLOCK DIAGRAM OF E1 CHASSIS
10
.
7. IC DATASHEETS&SPECS
7.1)VCT 49XYI
GENERAL DECRIPTION
The VCT 49xyI is an IC family of high-quality singlechip TV processors. Modular design and deepsubmicron technology allow the economic integration of features in all classes of single-scan TV sets.
The VCT 49xyI family is based on functional blocks contained and approved in existing products like
DRX 396xA, MSP 34x5G, VSP 94x7B, DDP 3315C, and SDA 55xx.
Each member of the family contains the entire IF, audio, video, display, and deflection processing for
4:3 and 16:9 50/60-Hz mono and stereo TV sets. The integrated microcontroller is supported by a
powerful OSD generator with integrated Teletext & CC acquisition including on-chip page memory.
Features
The VCT 49xyI family offers a rich feature set,
overing the whole range of state-of-the-art
50/60-Hz TV applications.
– PSSDIP88-1/-2 package
– PMQFP144-2 package
– Submicron CMOS technology
– Low-power standby mode
– Single 20.25 MHz reference crystal
– 8-bit 8051 instruction set compatible CPU
– Up to 256 kB on-chip program ROM
– WST, PDC, VPS, and WSS acquisition
– Closed Caption and V-chip acquisition
– Up to 10 pages on-chip teletext memory
– Multi-standard QSS IF processing with single SAW
– FM Radio and RDS with standard TV tuner
– TV-sound demodulation:
• all A2 standards
• all NICAM standards
• BTSC/SAP with MNR (DBX optional)
• EIA-J
– Baseband sound processing for loudspeaker
channel:
• volume and balance
11
• bass/treble or equalizer
• loudness and spatial effect (e.g. pseudo stereo)
• Micronas AROUND (virtual Dolby optional)
• Micronas BASS
• further optional and licence requiring sound enhancements as BBE, SRS Wow and Micronas
VOICE
– CVBS, S-VHS, YCrCb and RGB inputs
– 4H adaptive comb filter (PAL/NTSC)
– multi-standard color decoder (PAL/NTSC/SECAM)
– Nonlinear horizontal scaling “panorama vision”
– Luma and chroma transient improvement (LTI, CTI)
– Non-linear color space enhancement (NCE)
– Dynamic black level expander (BLE)
– Scan velocity modulation output
– Soft start/stop of H-drive
– Vertical angle and bow correction
– Average and peak beam current limiter
– Nonlinear and dynamic EHT compensation
– Black switch off procedure (BSO)
12
PIN CONNECTIONS AND SHORT DESCRIPTIONS
NC = not connected
LV = if not used, leave vacant
OBL = obligatory; connect as described in circuit diagram
IN = Input Pin
OUT = Output Pin
SUPPLY = Supply Pin
Pin
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Pin Name
GND
VSUP8.0AU
VREFAU
SPEAKERL
SPEAKERR
AOUT1L
AOUT1R
AIN3L/AOUT2L
AIN3R/AOUT2R
AIN2L
AIN2R
AIN1L
AIN1R/SIF
TAGC
VREFIF
IFINIFIN+
RESETQ
VSUP5.0FE
VSUP5.0IF
VSUP3.3DIG
GND
GND
VSUP1.8DIG
XTAL1
XTAL2
P22
P23
VIN11
VIN10
VIN9
VIN8
VIN7
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
VOUT1
VOUT2
VOUT3
Type
SUPPLY
SUPPLY
OUT
OUT
OUT
OUT
IN/OUT
IN/OUT
IN
IN
IN
IN/OUT
OUT
IN
IN
IN/OUT
SUPPLY
SUPPLY
SUPPLY
SUPPLY
SUPPLY
SUPPLY
IN
OUT
IN/OUT
IN/OUT
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
Connection
(If not
used)
OBL
OBL
OBL
LV
LV
LV
LV
LV
LV
GND
GND
GND
GND
LV
OBL
VREFıf
VREFıf
OBL
OBL
OBL
OBL
OBL
OBL
OBL
OBL
OBL
LV
LV
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
LV
LV
LV
Short Description
Ground Platform
Supply Voltage Analog Audio, 8.0 V
Reference Voltage, Audio
Analog Loudspeaker Output, Right
Analog Loudspeaker Output, Right
Analog Audio 1 Output, Left
Analog Audio 1 Output, Right
Analog Audio 3 Input, Left / Analog Audio 2 Output, Left
Analog Audio 3 Input, Right / Analog Audio 2 Output, Right
Analog Audio 2 Input, Left
Analog Audio 2 Input, Right
Analog Audio 1 Input, Left
Analog Audio 1 Input Right/Analog 2nd Sound IF Output
Tuner AGC Output
Reference Voltage, IF ADCs
Differential IF Input
Differential IF Input
Reset Input/Output
Supply Voltage Analog IF Front-end, 5.0 V
Supply Voltage IF ADC, 5.0 V
Supply Voltage Digital Core, 3.3 V
Ground Platform
Ground Platform
Supply Voltage Digital Core, 1.8 V (main and stand by supply)
Analog Crystal Input
Analog Crystal Output
Port 2, Bit 2 Input/Output
Port 2, Bit 3 Input/Output
Analog Video 11 Input
Analog Video 10 Input
Analog Video 9 Input
Analog Video 8 Input
Analog Video 7 Input
Analog Video 6 Input
Analog Video 5 Input
Analog Video 4 Input
Analog Video 3 Input
Analog Video 2 Input
Analog Video 1 Input
Analog Video 1 Output
Analog Video 2 Output
Analog Video 3 Output
13
43
44
45
VSUP1.8FE
GND
GND
SUPPLY OBL
SUPPLY OBL
SUPPLY OBL
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
VSUP3.3FE
P10
P11
P12
P13
P14
P15
P16
P17
P20
P21
SCL
SDA
VPROT
HOUT
HFLB
SAFETY
GNDDAC
VSUP3.3DAC
VSUP3.3IO
GND
GND
VSUP3.3BE
XREF
VRD
BOUT
GOUT
ROUT
SVMOUT
BIN
GIN
RIN
FBIN
GNDM
SENSE
RSW1
RSW2
EW
VERTVERT+
TEST
VSUP5.0BE
GND
SUPPLY
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN/OUT
IN
OUT
IN
IN
SUPPLY
SUPPLY
SUPPLY
SUPPLY
SUPPLY
SUPPLY
OBL
LV
LV
LV
LV
LV
LV
LV
LV
LV
LV
OBL
OBL
GND
LV
HOUT
GND
OBL
OBL
OBL
OBL
OBL
OBL
OBL
OBL
OUT
VSUP5.0BE
OUT
VSUP5.0BE
OUT
VSUP5.0BE
OUT
VSUP5.0BE
IN
GND
IN
GND
IN
GND
IN
GND
IN
GND
IN
GND
OUT
LV
OUT
LV
OUT
GND
OUT
GND
OUT
GND
IN
GND
SUPPLY OBL
SUPPLY OBL
Supply Voltage Analog Video Front-end, 1.8 V (main and stand by
supply)
Ground Platform
Ground Platform
Supply Voltage Analog Video Front-end, 3.3 V (main and stand by
supply)
Port 1, Bit 0 Input/Output
Port 1, Bit 1 Input/Output
Port 1, Bit 2 Input/Output
Port 1, Bit 3 Input/Output
Port 1, Bit 4 Input/Output
Port 1, Bit 5 Input/Output
Port 1, Bit 6 Input/Output
Port 1, Bit 7 Input/Output
Port 2, Bit 0 Input/Output
Port 2, Bit 1 Input/Output
I²C Bus Clock Input/Output
I²C Bus Data Input/Output
Vertical Protection Input
Horizontal Drive Output
Horizontal Flyback Input
Safety Input
Ground Video DACs
Supply Voltage Video DACs, 3.3 V
Supply Voltage I/O Ports, 3.3 V (main and Standby supply)
Ground Platform
Ground Platform
Supply Voltage Analog Video Back-end, 3.3 V
Reference Current for RGB DACs
Reference Voltage for RGB DACs
Analog Blue Output
Analog Green Output
Analog Red Output
Scan Velocity Modulation Output
Analog Blue Input, Back-end
Analog Green Input, Back-end
Analog Red Input, Back-end
Fast Blank Input, Back-end
Reference Ground for Sense ADC
Sense ADC Input
Range Switch 1 Output
Range Switch 2 Output
Vertical Parabola Output
Differential Vertical Sawtooth Output
Differential Vertical Sawtooth Output
Test Input, reserved for Test
Supply Voltage Analog Video Back-end, 5.0 V
Ground Platform
14
7.2)TDA 8357
GENERAL DESCRIPTION
The TDA8357J is a power circuit for use in 90° and
110° colour deflection systems for 25 to 200 Hz field
frequencies, and for 4 : 3 and 16 : 9 picture tubes. The IC
contains a vertical deflection output circuit, operating as a
high efficiency class G system. The full bridge output
circuit allows DC coupling of the deflection coil in
combination with single positive supply voltages.
The IC is constructed in a Low Voltage DMOS (LVDMOS)
process that combines bipolar, CMOS and DMOS
devices. DMOS transistors are used in the output stage
because of absence of second breakdown.
FEATURES
• Few external components required
• High efficiency fully DC coupled vertical bridge outputcircuit
• Vertical flyback switch with short rise and fall times
• Built-in guard circuit
• Thermal protection circuit
• Improved EMC performance due to differential inputs
SYMBOL PARAMETERS
Supplies
Vp
Supply voltage
VFB
flyback supply voltage
Iq(P)(av)
average quiescent supply current
Iq(FB)(av)
Iq(FB)(av)
Ptot
total power dissipation
Inputs and outputs
Vi(p-p)
input voltage (peak-to-peak value)
Io(p-p)
output current (peak-to-peak value)
Flyback switch
Io(peak)
maximum (peak) output current
Thermal data; in accordance with IEC 60747-1
Tstg
storage temperature
Tj
junction temperature
CONDITIONS
during scan
during scan
t ≤ 1.5 ms
MIN.
TYP.
MAX
UNIT
7.5
2 x VP
-
12
45
10
-
18
66
15
10
8
V
V
mA
mA
W
-
1000
-
1500
2.0
mV
A
-
-
± 1.2
A
-55
-
-
+150
+150
ºC
ºC
7.3)MC14052B
The MC14052B analog multiplexer is a digitally–controlled analog switch.
The MC14052B effectively implements a DP4T solid state switch. This
device’s feature low ON impedance and very low OFF leakage current.
Control of analog signals up to the complete supply voltage range can be
achieved.
• Triple Diode Protection on Control Inputs
• Switch Function is Break Before Make
• Supply Voltage Range = 3.0 Vdc to 18 Vdc
15
•
•
•
Analog Voltage Range (VDD – VEE) = 3.0 to 18 V Note: VEE must be _ VSS
Linearized Transfer Characteristics
Low–noise – 12 nV//Cycle, f . 1.0 kHz Typical
This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum
rated voltages to this high–impedance circuit. For proper operation, Vin and Vout should be constrained
to the range VSS _ (Vin or Vout) _ VDD. Unused inputs must always be tied to an appropriate logic
voltage level (e.g., either VSS, VEE or VDD). Unused outputs must be left open.
7.4)AN5277(Dual Channel SEPP Power Amplifier)
The AN5277 is a monolithic integrated circuit designed for 10.0 W (26 V, 8 W)output audio power
amplifier. It is a dual channel SEPP IC suitable for stereo operation in TV application.
Features
• Few external components :
• No Boucherot cells(output C, R)
• No Bootstrap Capacitors
• No Negative Feedback Capacitors
• Built-in muting circuit
• Built-in standby circuit
• Built-in various protection circuits (Load-short, thermal, over-voltage and current)
• High ripple rejection(55 dB)
• Compatible with AN5275, AN5276
• Operating voltage range 10 ~ 32 V(26 V typ.)
7.5)ICE1QS01(Controller for Switch Mode Power Supplies Supporting Low Power
Standby and Power Factor Correction (PFC))
Features
• Line Current Consumption with PFC
• Standby Input Power < 1 W
• Stable Standby Frequency
16
•
•
•
•
•
•
•
•
•
•
•
Low Power Consumption
Very Low Start-up Current
Soft-Start for noiseless Start-up
Standby Burst Mode with and without
Control Signal for lowered Output Voltages
Digital Frequency Reduction in small Steps
at Decreasing Load
Over- and Undervoltage Lockout
Switch Off at Mains Undervoltage
Mains Voltage Dependent Fold Back Point
Correction
Ringing Suppression Time Controlled from
Output Voltage
Easy Design In
Free usable Fault Comparator
Functional Description
The ICE1QS01 is optimized to control free running flyback converters with and without Power Factor
Correction (with PFC Charge Pump). The switching frequency is reduced in small steps with
decreasing load towards a minimum of 20 kHz in standby mode. This function is performed by a digital
circuit to avoid any jitter also with periodically pulsed loads. To provide extremely low power
consumption at light loads, this device can be switched into Standby Burst Mode. This is also possible
without standby control signal (for adapter application). Additionally, the start up current is very low. To
avoid switching stresses of the power devices, the power transistor is always switched on at minimum
voltage. The device has several protection functions: VCC overand undervoltage, mains undervoltage
and current limiting. Regulation can be done by using the internal error amplifier or an opto coupler
feedback. The output driver is ideally suited for driving a power MOSFET. The ICE1QS01 is suited for
TV-sets, VCR- sets, SAT- receivers and other consumer applications in the power range from 0 to app.
300 W.
17
.
8. PIN VOLTAGES OF IC’S
0
45
GND
Supply Voltage Analog Audio, 8.0 V
8,13
1,35
46
Reference Voltage, Audio
3,67
0
47
SPEAKERL
Analog Loudspeaker Output, Right
3,72
0
5
SPEAKERR
Analog Loudspeaker Output, Right
3,72
6
AOUT1L
Analog Audio 1 Output, Left
7
AOUT1R
8
AIN3L/AOUT2L
9
AIN3R/AOUT2R
Analog Audio 1 Output, Right
Analog Audio 3 Input, Left / Analog
Audio 2 Output, Left
Analog Audio 3 Input, Right / Analog
Audio 2 Output, Right
10
AIN2L
11
AIN2R
12
AIN1L
13
14
Short Description
1
GND
Ground Platform
2
VSUP8.0AU
3
VREFAU
4
Short Description
ST-BY
0
Pin Name
V DC
Pin
No Pin Name
Pin
No
V DC
ST-BY
IC 101(VCTI)
Video-Controller-Text-IFAudio IC Family
0
0
VSUP3.3FE
Ground Platform
Supply Voltage Analog Video Frontend, 3.3 V
3,3
3,3
P10
Port 1, Bit 0 Input/Output
3,27
0
48
P11
Port 1, Bit 1 Input/Output
0
3,27
0
49
P12
Port 1, Bit 2 Input/Output
3,3
3,29
3,72
0
50
P13
Port 1, Bit 3 Input/Output
0
3,28
3,72
0
51
P14
Port 1, Bit 4 Input/Output
0
0
3,43
0
52
P15
Port 1, Bit 5 Input/Output
0
0
3,44
0
53
P16
Port 1, Bit 6 Input/Output
2,77
2,77
Analog Audio 2 Input, Left
3,7
0
54
P17
Port 1, Bit 7 Input/Output
2,79
2,79
Analog Audio 2 Input, Right
3,7
0
55
P20
Port 2, Bit 0 Input/Output
3,32
2,9
3,7
0
56
P21
Port 2, Bit 1 Input/Output
3,24
0,6
AIN1R/SIF
Analog Audio 1 Input, Left
Analog Audio 1 Input Right/Analog
2nd Sound IF Output
3,7
0
57
SCL
I²C Bus Clock Input/Output
3,3
3,06
TAGC
Tuner AGC Output
3,77
0,82
58
SDA
I²C Bus Data Input/Output
3,3
3,06
15
VREFIF
Reference Voltage, IF ADCs
2,42
0,9
59
VPROT
Vertical Protection Input
0,05
0
16
IFIN-
Differential IF Input
2,43
0,76
60
HOUT
Horizontal Drive Output
1,55
3,29
17
IFIN+
Differential IF Input
2,43
0,76
61
HFLB
Horizontal Flyback Input
0,65
0
18
RESETQ
3,29
3,27
62
SAFETY
Safety Input
0,03
0,43
19
VSUP5.0FE
Reset Input/Output
Supply Voltage Analog IF Front-end,
5.0 V
4,96
1
63
GNDDAC
Ground Video DACs
20
VSUP5.0IF
Supply Voltage IF ADC, 5.0 V
4,92
1
64
VSUP3.3DAC
21
VSUP3.3DIG
Supply Voltage Digital Core, 3.3 V
3,14
1
65
VSUP3.3IO
Supply Voltage Video DACs, 3.3 V
Supply Voltage I/O Ports, 3.3 V
(main and Standby supply)
22
GND
Ground Platform
0
0
66
GND
Ground Platform
23
GND
0
0
67
GND
24
VSUP1.8DIG
Ground Platform
Supply Voltage Digital Core, 1.8 V
(main and stand by supply)
1,85
1,97
68
VSUP3.3BE
Ground Platform
Supply Voltage Analog Video Backend, 3.3 V
3,28
1
25
XTAL1
Analog Crystal Input
1,71
1,7
69
XREF
Reference Current for RGB DACs
1,22
0
26
XTAL2
Analog Crystal Output
1,74
1,72
70
VRD
Reference Voltage for RGB DACs
1,24
0,95
27
P22
Port 2, Bit 2 Input/Output
3,27
3,26
71
BOUT
Analog Blue Output
4,66
1
28
P23
Port 2, Bit 3 Input/Output
3,27
3,26
72
GOUT
Analog Green Output
4,66
1
29
VIN11
Analog Video 11 Input
0,12
0,09
73
ROUT
Analog Red Output
4,66
1
30
VIN10
Analog Video 10 Input
0
0,09
74
SVMOUT
Scan Velocity Modulation Output
1,77
0,37
31
VIN9
Analog Video 9 Input
0,5
0,09
75
BIN
Analog Blue Input, Back-end
0,19
0
32
VIN8
Analog Video 8 Input
0,5
0,09
76
GIN
Analog Green Input, Back-end
0,19
0
33
VIN7
Analog Video 7 Input
0,99
0,09
77
RIN
Analog Red Input, Back-end
0,19
0
34
VIN6
Analog Video 6 Input
0,99
0,09
78
FBIN
Fast Blank Input, Back-end
0,07
0,07
35
VIN5
Analog Video 5 Input
0,99
0,09
79
GNDM
Reference Ground for Sense ADC
0
0
36
VIN4
Analog Video 4 Input
1
0,09
80
SENSE
Sense ADC Input
0,23
0
37
VIN3
Analog Video 3 Input
1
0,09
81
RSW1
Range Switch 1 Output
0,03
0
38
VIN2
Analog Video 2 Input
1
0,09
82
RSW2
Range Switch 2 Output
0,01
0
39
VIN1
Analog Video 1 Input
1
0,09
83
EW
Vertical Parabola Output
4,37
0
40
VOUT1
Analog Video 1 Output
1,08
1,49
84
VERT-
Differential Vertical Sawtooth Output
0,82
0
41
VOUT2
Analog Video 2 Output
1,08
1,49
85
VERT+
Differential Vertical Sawtooth Output
0,79
0
42
VOUT3
1,17
0,98
86
TEST
0
VSUP1.8FE
1,9
1,9
87
VSUP5.0BE
Test Input, reserved for Test
Supply Voltage Analog Video Backend, 5.0 V
3,71
43
Analog Video 3 Output
Supply Voltage Analog Video Frontend, 1.8 V
44
GND
Ground Platform
0
0
88
GND
Ground Platform
18
0
0
3,29
1
3,31
3,31
0
0
0
0
5,01
0
0
0
N.C
NOT CONNECTED
0
0
7
CH.2 OUT
CHANNEL 2 OUTPUT
2
CH.1 IN.
CHANNEL 1 INPUT
0
0
8
MUTE
MUTE
3
RF
RIPPLE FILTER
9
GND(OUTPUT) OUTPUT GROUND
4
GND(INPUT) INPUT GROUND
0
0
10
Vcc
Vcc
25,3 8,47
5
CH.2 IN
CHANNEL 2 INPUT
0
0
11
ST-BY
STANDBY
16,5 0,43
6
N.C
NOT CONNECTED
0
0
12
CH.1 OUT
CHANNEL 1 OUTPUT
Short Description
23,1 0,76
Pin
No
Pin Name
Short Description
12
ST-BY
ST-BY
1
Pin
No Pin Name
V DC
V DC
IC 301(AN 5277)
Dual Channel SEPP Power Amplifier
0
0,37 4,44
0
12
0
0
V DC
ST-BY
V DC
ST-BY
IC 602(ICE1QS01)
Dual Channel SEPP Power Amplifier
0
0
5
OFC
OVERVOLTAGE FAULT
COMPARATOR
0
0
1,3
9,06
6
GND
GROUND
0
0
RZI
REGULATION AND ZERO CROSSING
INPUT
1,35 0,04
7
OUT
OUTPUT
1,79
0
SRC
SOFT-START AND REGULATION
CPACITOR
8
Vcc
SUPPLY VOLTAGE
11,4 10,1
Pin
No Pin Name
Short Description
1
N.C
NOT CONNECTED
2
PCS
PRIMARY CURRENT SIMULATION
3
4
2,76 0,34
Pin
No
Pin Name
Short Description
Pin Name
Short Description
ST-BY
Pin
No
V DC
Short Description
ST-BY
Pin
No Pin Name
V DC
IC 501(TDA 8357)
VERTICAL DEFLECTION
1
INA
INPUT A
0,79
0
6
Vfb
FLAYBACK SUPPLY COLTAGE
46,5
0
2
INB
INPUT B
0,77
0
7
OUTA
OUTPUT A
6,46
0
3
Vp
SUPPLY VOLTAGE
12,4
0
8
GUARD
GUARD OUTPUT
0,25
0
4
OUTB
OUTPUT B
6,5
0
9
FEEDB
FEEDBACK INPUT
6,55
0
5
GND
GROUND
0
0
19
9. OSCILLOSGRAPHS OF SOME IC PINS
.
Note : A pattern Generator is connected to the TV (Colour Bar, sound 1 kHZ)
9.1
VCTI-IC 101
Pin 02, Supply Voltage Analog Audio, 15625 kHz
Pin 06, Analog Audio 1 Output, Left, 15625 kHz
Pin 07, Analog Audio Output, Right, 15625 kHz
Pin 08, Analog Audio 3 Input,Left, 15625 kHz
Pin 09, Analog Audio 3 Input,Right, 15625kHz
Pin 38, Analog Video 2 Input, 15625kHz
20
Pin 40, Analog Video 1 Output, 15625 kHz
Pin 41, Analog Video 2 Output, 15625 kHz
Pin 60, Horizontal Drive Ouput, 15625 kHz
Pin 61, Horizontal Fylback Input, 15625 kHz
Pin 71, Analog Blue Ouput, 15625 kHz
Pin 72, Analog Green Ouput 15625 kHz
21
Pin 73, Analog Red Ouput, 15625 kHz
Pin 80, Sense ADC Input, 15625 kHz
Pin 84,Differential Vert. Sawtooth Out(VERT-), 15625 kHz
Pin 85, Differential Vert. Sawtooth Out(VERT+), 15625 kHz
9.2
TDA 2822-IC 301
Pin 1, Input A, 15625 kHz
Pin 2, Input B, 15625 kHz
22
Pin 3, Supply Voltage, 15625 kHz
Pin 4, Output B, 15625 kHz
Pin 6, Flyback Supply Voltage, 15625 kHz
Pin 7, Output A, 15625 kHz
Pin 8, Guard Output, 15625 kHz
Pin 9, Feedback Input, 15625 kHz
23
10. ELECTRICAL ADJUSTMENTS
.
1. ELECTRICAL ADJUSTMENTS
1.1 Supply Voltage Adjustment
Connect a digital voltmeter to the cathode of diode D609 at the AV mode of the TV and set the screen voltage
to the minimum with the screen potentiometer. Adjust the main supply voltage (B+) with P602 potentiometer to
the following value (after supply adjustment, readjust Screen and focus voltage).
20”
: 114 VDC (for A48ECR43X51)
21”
: 111 VDC (for A51EFS13X191)
21”
: 114 VDC (for A51EER33X78)
21” PF
: 122 VDC (for A51QDX993X030)
21” PF
: 125 VDC (for A51ERF135X80)
21” PF
: 125 VDC (for A51ELD032X001)
2. SERVICE ADJUSTMENTS
To enter the Service Mode, ‘Service In/Out” button on the Service Remote Control or activate the “Picture Menu”
with the user remote control and press “9301” (Press “0” button to exit the Service Mode). To exit from the
service menu, TV/TX button should be typed on the Remote Control.
While the service menu is on screen, version and the date of the software are written on right bottom of the
screen.
For Example:
SK12256-01 T01
20:29:29
24/12/04
2.1 AGC Adjustment
•
•
•
•
•
•
•
•
•
•
Switch to Service Menu
Find the “AGC METHOD” under “OPTIONS” sub-menu with P+/P-,
Set its value to “SYNC+PEAK WHITE”.
Find “AGC” under “IF ADJ.” sub-menu with P+/P-,
Set its value to “4”
Find “AGC FOR VHF I” under “IF ADJ.” sub-menu with P+/P-,
Set its value to “4”
Set “PIP AGC” topic‘s value to “15”
Set “PIP AGC FOR VHF I” topic‘s value to “20”
Exit from the service menu.
2.2 Screen Adjustment
•
•
•
•
•
•
Switch the TV to the AV mode
Do not make any connecttion from the scart switch
Switch on the service menu
Set the value of “BLUEBLACK” option to “OFF”
Set the value of the “SCREEN ADJ.” to the indicated value in FACTORY SETTINGS TABLE
Press “OK” button on the RC
24
•
•
•
There should appear a horizontal line on the center of the set
Adjsut the screen potentiometre to set the line at the first seen point.
Exit from the service menu
2.3 White Balance Adjustment
•
•
•
•
•
•
•
Apply a white pattern with a pattern generator to the antenna input.
Enter the Service Menu and access to VIDEO ADJ. I sub-menu
Set the value of “G.CUT OFF” value to “156” and “G.DRIVE” value to “356”.
Adjust red drive with“R.DRIVE” and blue drive with “B.DRIVE” .
Adjust red cut off with “R.CUT OFF” and blue cut off with “B. CUT OFF”
If white balance can not be adjusted properly, slightly change the values of “G.CUT OFF” and “G.DRIVE”.
Exit from Service menu.
2.4 Geometry Adjustments
•
•
•
•
•
•
•
•
•
•
•
Apply the cross hatch pattern with a pattern generator to the antenna input.
Enter Service Menu and access to GEOMETRY sub-menu
The options, “50Hz GEOM.”, “50Hz. GEOM.HOR.II”, “50Hz GEOM.EHT” are for PAL/SECAM.
The options, “60Hz GEOM.”, “60Hz. GEOM.HOR.II”, “60Hz GEOM.EHT” are for NTSC.
Adjust Vertical Amplitude with “VERTICAL AMPLITUDE” option.
Adjust vertical centring with “VERTICAL SHIFT”, vertical linearity with “LINEARITY” , vertical s-correction with
“S-CORRECTION”, vertical parallelogram with “VERTICAL ANGLE”, vertical bow with “VERTICAL BOW”,
horizontal centering with “HORIZONTAL SHIFT”, trapeze adjustment with “TRAPEEZE CORR.I”, general
parabole adjustment with “CUSHION CORR.I” options.
Adjust the parabole of the top corners with “UPPER CORNER 1” and “UPPER CORNER 2”.
Adjust the parabole of the bottom corners with “LOWER CORNER 1” and “LOWER CORNER 2”.
Adjust the horizontal OSD centering with “HORIZONTAL OSD POSITION” and vertical OSD centering with
“VERTICAL OSD POSITION”
For NTSC adjustments, connect an NTSC signal from AV1 follow the adjustments explained above under
the sub-menus “60Hz GEOM.”, “60Hz. GEOM.HOR.II”, “60Hz GEOM.EHT”.
Exit from the Service Menu.
2.5 Options Menu
Enter the Service Menu with the Service RC and and access to OPTION sub-menu and the options and their
defitinons are written below.
AV1YUV
: AVAILABLE(Component input is available from Scart 1); N/A(Not Available)
AV2&AV3
: AV2&AV3 N/A (Not Available); AV2 AVAIL.-AV3 N/A (AV1 Available, AV2 Not Av.);
AV2&AV3 AVAILABLE ( Both Available)
AV4
: NONE(No Front AV); CVBS+SVHS(Both Available); CVBS ONLY(Front AV Available);
SVHS ONLY(SVHS available)
TELETEXT
: DEFAULT(Teletext); FASTEXT; TOPTEXT; FASTEXT+TOPTEXT
LANGUAGE
: A (English, French, German, Italien, Spanish, Portuguese, Dutch, Greek, Danish, Swedish,
Finnish, Norwegian, Turkish, Hebrew, Russian, Hungarian, Slovak, Czech, Polish, Albanian,
Macedonian, Serbian, Slovenian, Romanian, Croatia, Bulgarian);
B (English, French, German, Italian, Dutch, Greek, Danish, Swedish, Spanish, Portuguese,
Norwegian, Finnish, Albanian, Macedonian, Turkish, Russian, Hebrew, Hungarian, Croatia,
Romanian, Bulgarian, Slovenian, Czech, Slovak, Arabish, Persian)
TXT TABLE
: AUTO; WEST(English, French, German, Turkish, Spanish, Italian, Finnish, Swedish, Norwegian,
Danish); EAST(Polish, French, Hungarian, Czech, German, Slovenian, Italian, Romanian);
GREEC(English, French, Turkish, German, Finnish, Norwegian, Swedish, Danish, Spanish, Italian,
Greek); CYRILLIC(English, Russian, German, Czech, Estonian, Ukrainian, Latvian); ARABIC(English,
25
French, German, Turkish, Spanish, Italian, Finnish, Swedish, Norwegian, Danish, Arabic);
FARSI(English, French, German, Turkish, Spanish, Italian, Finnish, Swedish, Norwegian, Danish,
Persian); HEBREW(English, French, German, Tuskish, Italian, Finnish, Swedish; Norwegian,Danish)
CRT
: 4:3; 16:9
PIP
: AVAILABLE; N/A
MAIN TUNER : Philips; Panasonic DB2G3-DA5G3; Temic; Panasonic D44G3; Sharp or Alps
PIP TUNER
: Philips; Panasonic DB2G3-DA5G3; Temic; Panasonic D44G3; Sharp or Alps
SVM&DCI
: ON; OFF; MENU
BLUEBLACK
: ON(blueblack acticated), OFF(Blueblack inactivated)
LTI&COMB
: ON; OFF
CTI
:ON(Colour Transition Improvement available); OFF(N/A)
ADAPTIVE PKG : ON(Digital Noise Reduction available); OFF(N/A); MENU(via menu)
PROTECTION : N/A(No Protection circuit); BCL ONLY(Only Beem Current Limiting available); VERTICAL ONLY(
Only Vertical protection avaliable); BCL&VERTICAL(Both avaliable)
PANORAMA : AVAILABLE; N/A
KEYBOARD
: P-P+V-V+; MENU P/V-+
CALCULATOR : AVAILABLE; N/A
ALARM TIMER : AVAILABLE; N/A
DEMO
: 0(Otoprogram in first start, closed); 1(open)
2.6 Sound Options Menu
BG
: EUROPE(BG Europe); NEW ZELLAND(BG New Zelland); AUSTRALIA(BG Australia); N/A(BG not
avaliable)
DK
: AVAILABLE; N/A
I
: AVAILABLE; N/A
L/L’
: AVAILABLE; N/A
FM RADIO
/ TV GUIDE : NONE(Radio&EPG, not available); FM RADIO(Only radio avaliable); TV GUIDE(Only TV Guide
avaliable)
NICAM
: AVAILABLE; N/A
DOLBY VITUAL : AVAILABLE; N/A
BASS OPTION : DYNAMIC BASS(Dynamic Bass avaliable); SUBWOOFER(Subwoofer avaliable); NONE
HEADPHONE : AVAILABLE; N/A
CARRIER MUTE : VIA MSP; VIA MICRO
PAT
: AVAILABLE(Picture and Text avaliable); N/A
SIMPLE HOTEL : AVAILABLE; N/A
HOTEL MAX
VOL
: Limites the max volume level in hotel mode
AGC METHOD : SYNC PEAK WHITE; FIXED
TILT
: N/A; AVAILABLE
CRT 4:3
MODE 16:9
: VIA FLYBL(Prevents cut off line to be seen by shifting up); DISABLE CUTOFF( Directly Prevents Cut
off line to be seen)
2.7 Hotel Mode
If “Simple Hotel” option in the Service Menu is selected as “ON”, to access set up menu “4658” should be typed
whilst the “Features Menu” is on screen. After finishing the adjustments by taking the TV to St.by or shutting down,
the access can be re-inhibited.
26
2.8 Factory Settings for Service Mode
FACTORY SETTINGS FOR SERVICE MODE
VIDEO ADJ. I
R.DRIVE
G.DRIVE
B.DRIVE
R. CUTOFF
G. CUTOFF
B. CUTOFF
IBRM
WDRM
SCREEN ADJ.
VIDEO ADJ. II
BCL GAIN
BCL TRESHOLD
BCL TRESHOLD II
BCL TIME CONSTANT 1
BCL TIME CONSTANT 2
OSD BRIGHTNESS
OSD CONTRAST
TXT BRIGHTNESS
TXT CONTRAST
YC DELAY FOR PAL
YC DELAY FOR SECAM
YC DELAY FOR NTSC
SUBCARRIER ADJ.
VIDEO ADJ. III
DPWL GAIN
DPWL START P.
PWL TIME CONSTANT
PWL
SVM GAIN
SVM CORING
SVM LIMITTER
SVM DELAY
SVM DIFF. WINDOW
PIP POSITION
HORIZONTAL
VERTICAL
SOUND OPTIONS
BCL DELTA
TILT
50HZ GEOM. EHT
EHT TRESHOLD
EHT TIME CONSTANT
VERTICAL EHT 1
VERTICAL EHT 2
HORIZONTAL EHT 1
HORIZONTAL EHT 2
EHT DTC
EHT P1
EHT P2
60 HZ GEOM. EHT
EHT TRESHOLD
EHT TIME CONSTANT
VERTICAL EHT 1
VERTICAL EHT 2
HORIZONTAL EHT 1
HORIZONTAL EHT 2
EHT DTC
EHT P1
EHT P2
20"
356
356
356
156
156
156
280
290
250
21"SF (SS8)
356
356
356
156
156
156
280
270
297
21" VC6
356
356
356
156
156
156
260
270
375
310
245
155
511
0
135
140
130
135
9
2
10
8
280
180
175
511
0
130
120
100
120
9
2
10
18
280
180
175
511
0
130
120
100
120
9
2
10
18
-300
380
1
60
0
0
0
0
0
-300
500
1
70
0
0
0
0
0
-300
500
1
70
0
0
0
0
0
50
0
50
0
50
0
63
60
-142
-122
0
0
-50
-49
-50
63
60
-110
-120
0
0
-50
-49
-50
63
60
-110
-120
0
0
-50
-49
-50
50
40
-109
-123
0
0
-50
-39
-34
50
40
-123
-120
0
0
-50
-50
-55
50
40
-123
-120
0
0
-50
-50
-55
50 HZ GEOM.
VERTICAL AMPLITUDE
VERTICAL SHIFT
LINEARITY
S-CORRECTION
VERTICAL ANGLE
VERTICAL BOW
START LINE MEASUR.
VER. BLANKING STOP
VER. BLANKING START
HORIZONTAL WIDTH
HORIZONTAL SHIFT
TRAPEZE CORR. I
CUSHION CORR. I
UPPER CORNER 1 I
LOWER CORNER 1 I
UPPER CORNER 2 I
LOWER CORNER 2 I
HOR. BLANKING STOP
HOR. BLANKING START
HOR. OSD POSITION
VER. OSD POSITION
60 HZ GEOM.
VERTICAL AMPLITUDE
VERTICAL SHIFT
LINEARITY
S-CORRECTION
VERTICAL ANGLE
VERTICAL BOW
START LINE MEASUR.
VER. BLANKING STOP
VER. BLANKING START
HORIZONTAL WIDTH
HORIZONTAL SHIFT
TRAPEZE CORR. I
CUSHION CORR. I
UPPER CORNER 1 I
LOWER CORNER 1 I
UPPER CORNER 2 I
LOWER CORNER 2 I
HOR. BLANKING STOP
HOR. BLANKING START
HOR. OSD POSITION
VER. OSD POSITION
50 HZ GEOM. HOR. II
HOR. WIDTH II
VER. ZOOM II
FLYBL
TRAPEZE CORR. II
CUSHION CORR. II
UPPER CORNER 1 II
LOWER CORNER 1 II
UPPER CORNER 2 II
LOWER CORNER 2 II
60 HZ GEOM. HOR. II
HOR. WIDTH II
VER. ZOOM II
FLYBL
TRAPEZE CORR. II
CUSHION CORR. II
UPPER CORNER 1 II
LOWER CORNER 1 II
UPPER CORNER 2 II
LOWER CORNER 2 II
27
20"
-210
3
20
90
0
0
11
25
293
0
-27
0
0
0
0
0
0
225
1225
31
18
21"SF (SS8)
140
7
40
40
0
0
11
22
333
0
-44
0
0
0
0
0
0
205
1245
31
18
21" VC6
110
7
0
80
0
0
11
22
333
0
-37
0
0
0
0
0
0
205
1245
31
18
-198
7
0
-41
0
0
11
20
310
0
-61
0
0
0
0
0
0
225
1220
18
6
210
17
40
-30
0
0
12
18
333
0
-61
0
0
0
0
0
0
175
1235
120
18
10
0
0
0
12
18
333
0
-48
0
0
0
0
0
0
175
1235
16
8
110
47
16
0
0
0
0
0
0
110
68
14
0
0
0
0
0
0
110
60
14
0
0
0
0
0
0
110
50
10
0
0
0
0
0
0
0
65
10
0
0
0
0
0
0
0
57
10
0
0
0
0
0
0
FACTORY SETTINGS FOR SERVICE MODE
VIDEO ADJ. I
R.DRIVE
G.DRIVE
B.DRIVE
R. CUTOFF
G. CUTOFF
B. CUTOFF
IBRM
WDRM
SCREEN ADJ.
VIDEO ADJ. II
BCL GAIN
BCL TRESHOLD
BCL TRESHOLD II
BCL TIME CONSTANT 1
BCL TIME CONSTANT 2
OSD BRIGHTNESS
OSD CONTRAST
TXT BRIGHTNESS
TXT CONTRAST
YC DELAY FOR PAL
YC DELAY FOR SECAM
YC DELAY FOR NTSC
SUBCARRIER ADJ.
VIDEO ADJ. III
DPWL GAIN
DPWL START P.
PWL TIME CONSTANT
PWL
SVM GAIN
SVM CORING
SVM LIMITTER
SVM DELAY
SVM DIFF. WINDOW
PIP POSITION
HORIZONTAL
VERTICAL
SOUND OPTIONS
BCL DELTA
TILT
50HZ GEOM. EHT
EHT TRESHOLD
EHT TIME CONSTANT
VERTICAL EHT 1
VERTICAL EHT 2
HORIZONTAL EHT 1
HORIZONTAL EHT 2
EHT DTC
EHT P1
EHT P2
60 HZ GEOM. EHT
EHT TRESHOLD
EHT TIME CONSTANT
VERTICAL EHT 1
VERTICAL EHT 2
HORIZONTAL EHT 1
HORIZONTAL EHT 2
EHT DTC
EHT P1
EHT P2
21" PF
(SS0)
356
356
356
156
156
156
270
290
296
21"PF
(GS9)
356
356
356
156
156
156
280
240
250
21" PF
(VC0)
356
356
356
156
156
156
280
250
405
270
200
130
511
0
120
140
110
110
9
2
10
18
270
200
80
511
0
120
110
110
110
9
2
10
18
330
160
74
511
0
120
120
110
110
9
2
10
18
-300
400
1
90
0
0
0
0
0
-300
400
1
70
0
0
0
0
0
-300
400
1
90
0
0
0
0
0
50
0
20
0
50
0
70
40
-162
-160
0
0
0
0
0
70
40
-130
-50
0
0
0
0
0
70
40
-200
-40
0
0
0
0
0
80
40
-93
-80
0
0
0
0
0
80
40
-130
-40
0
0
0
0
0
80
40
-180
-40
0
0
0
0
0
50 HZ GEOM.
VERTICAL AMPLITUDE
VERTICAL SHIFT
LINEARITY
S-CORRECTION
VERTICAL ANGLE
VERTICAL BOW
START LINE MEASUR.
VER. BLANKING STOP
VER. BLANKING START
HORIZONTAL WIDTH
HORIZONTAL SHIFT
TRAPEZE CORR. I
CUSHION CORR. I
UPPER CORNER 1 I
LOWER CORNER 1 I
UPPER CORNER 2 I
LOWER CORNER 2 I
HOR. BLANKING STOP
HOR. BLANKING START
HOR. OSD POSITION
VER. OSD POSITION
60 HZ GEOM.
VERTICAL AMPLITUDE
VERTICAL SHIFT
LINEARITY
S-CORRECTION
VERTICAL ANGLE
VERTICAL BOW
START LINE MEASUR.
VER. BLANKING STOP
VER. BLANKING START
HORIZONTAL WIDTH
HORIZONTAL SHIFT
TRAPEZE CORR. I
CUSHION CORR. I
UPPER CORNER 1 I
LOWER CORNER 1 I
UPPER CORNER 2 I
LOWER CORNER 2 I
HOR. BLANKING STOP
HOR. BLANKING START
HOR. OSD POSITION
VER. OSD POSITION
50 HZ GEOM. HOR. II
HOR. WIDTH II
VER. ZOOM II
FLYBL
TRAPEZE CORR. II
CUSHION CORR. II
UPPER CORNER 1 II
LOWER CORNER 1 II
UPPER CORNER 2 II
LOWER CORNER 2 II
60 HZ GEOM. HOR. II
HOR. WIDTH II
VER. ZOOM II
FLYBL
TRAPEZE CORR. II
CUSHION CORR. II
UPPER CORNER 1 II
LOWER CORNER 1 II
UPPER CORNER 2 II
LOWER CORNER 2 II
28
21" PF
(SS0)
-250
2
20
140
0
0
11
20
333
0
-23
0
0
0
0
0
0
215
1235
31
18
21"PF
(GS9)
-170
2
12
130
0
0
14
22
333
0
-34
0
0
0
0
0
0
215
1235
31
18
21" PF
(VC0)
-105
2
-12
140
0
0
11
20
333
0
-39
0
0
0
0
0
0
210
1235
31
18
-206
9
0
-41
0
0
11
18
333
0
-42
0
0
0
0
0
0
190
1225
18
6
-180
4
-50
100
0
0
16
21
333
0
-50
0
0
0
0
0
0
175
1225
16
10
-130
5
-70
140
0
0
11
18
333
-57
-42
0
0
0
0
0
0
183
1225
18
9
110
60
14
0
0
0
0
0
0
110
50
17
0
0
0
0
0
0
110
60
14
0
0
0
0
0
0
110
60
10
0
0
0
0
0
0
110
60
10
0
0
0
0
0
0
110
60
10
0
0
0
0
0
0
11. CHANNEL FREQUENCY TABLE
.
29
30
12. SPARE PARTS LIST
InstPoint
AQUA
C01
C02-C03
C102
C103
C104-C109
C111-C128
C129
C130-C135
C136-C151
C152-C155
C156-C157
C158
C160
C161
C162-C163
C203-C210
C211-C212
C215-C219
C221-C224
C228-C230
C233-C235
C237-C240
C242
C247-C248
C249
C250
C251
C252-C253
C301
C302
C304-C307
C308
C309-C310
C311-C313
C315
C316-C317
C318-C321
C322
C323-C324
C325
C326
C327-C328
C329-C330
C331
C401
C402
C404-C405
C406-C407
C408-C410
C412-C420
C422-C424
C426-C428
C429-C431
C435-C437
C438
C440
C441
C442
C445-C446
C447
C502
C503
C504
C506-C507
C508-C509
C510
C511
C512
C513
C514
C514
C515
C517
C518
C519
C522
C523
C527
C528
C530
C531
C532
C533
C602
C603-C606
C608
Object description
AV3/KLK MODULE ASSY 21T29/T34 12.3SX
S-VHS AUTO INSER 29" 14.1
HEADPHONE JACK YKB21-5103
CPT SS A48ECR43X51 (HUNGARY)
DEGAUSSING COIL ASSY 20" BAND
K1 CHASSIS 20"P/SX/HP/AV/2SC A-OSD
KNOB POWER SWITCH SILV.MAS.20K08
KNOB VOL.20K08 SILVER PAINTED
KNOB PROGRAM VOLUME SILVER 20K08
RC BEKO TYPE SILVER C7/C8
SPEAKER 8R./5W (N) / 7W (MAX) 50X90
CABLE HARNESS
EC 47UF M 6.3V 11*5 R:5
CC-CHIP 100PF J 50V /1206 NPO
EC 47UF 16V 11*5 R:5
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 1NF K 50V /0603 X7R
CC-CHIP 100NF K 50V /0603 X7R
EC 3.3UF 16V 11*5 R:5
EC 100UF 16V 11*6 R:5
CC-CHIP 47PF J 50V /0603 NPO TAPE
CC-CHIP 22PF J 50V /0603 NPO TAPE
CC-CHIP 100PF J 50V /0603 NPO
CC-CHIP 27NF J 25V /0603 X7R
EC 4.7UF 63V 11*5 R:5
CC-CHIP 1UF K 16V /0805 X7R
CC-CHIP 1NF K 50V /0603 X7R
EC 4.7UF 16V 11*5 R:5
CC-CHIP 220PF J 50V /0603 NPO TAPE
CC-CHIP 22NF K 50V/0603 X7R TAPE
CC-CHIP 220PF J 50V /0603 NPO TAPE
EC 47UF 16V 11*5 R:5
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 4.7NF K 50V /0603 X7R
EC 47UF 16V 11*5 R:5
CC-CHIP 1NF K 50V /0603 X7R
EC 10UF 16V 5*3.5 R:5
CC-CHIP 220NF K 50V /0805 X7R
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 100PF J 50V /0603 NPO
CC-CHIP 10NF K 50V /0603 X7R
CC 1NF K 63V NPO R:5
CC-CHIP 1NF K 50V /0603 X7R
EC 10UF 16V 5*3.5 R:5
CC-CHIP 100NF K 50V /0603 X7R
EC 100UF 16V 11*6 R:5
CC-CHIP 47NF K 25V /0603 X7R TAPE
CC-CHIP 470NF K 16V /0805 X7R
CC-CHIP 1NF K 50V /0603 X7R
EC 100UF 25V 11*6 R:5
CC-CHIP 1.5NF K 50V /0603 X7R TAPE
CC-CHIP 68NF K 50V /0603 X7R
EC 1500UF 35V 20*13 R:5
EC 1000UF 16V 20*10 R:5
C-PEM 100NF J 100V R:5
C-CE 100NF 50V K R:5
EC 4.7UF 16V 11*5 R:5
CC-CHIP 22NF K 50V/0603 X7R TAPE
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 33NF K 50V /0603 X7R
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 1NF K 50V /0603 X7R
EC 10UF 16V 5*3.5 R:5
CC-CHIP 100NF K 50V /0603 X7R
EC 100UF 16V 11*6 R:5
CC-CHIP 330PF J 50V /0603 NPO
CC-CHIP 47NF K 25V /0603 X7R TAPE
EC 47UF 16V 11*5 R:5
CC-CHIP 100PF J 50V /0603 NPO
CC-CHIP 33PF J 50V /0603 NPO TAPE
CC-CHIP 10PF J 50V /0603 NPO TAPE
CC-CHIP 220NF Z 16V /0603 Y5V TAPE
CC 470PF K 500V Y5P R:5
CC-CHIP 100NF K 50V /0603 X7R
CC-CHIP 47NF K 25V /0603 X7R TAPE
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 100NF K 50V /0805 X7R
C-PEM 1NF J 100V R:5
C-PEM 47NF K 63V R:5
EC 47UF 25V 11*5 R:5
CC 220PF K 2KV Y5P R:5
CC-CHIP 1NF K 50V /0603 X7R
C-CE 100NF 50V K R:5
EC 4.7UF 50V 11*5 R:5
CC 10NF K 50V R:5
C-PEM 220NF J 100V R:5
CC 68PF J 500V NPO R:5
C-PEM 330NF J 250V R:15
JUMPER WIRE D=.6
C-PPM 9.1NF %3.5 1.5/1.6KV R:15 CLAS-B
C-PPM 360NF J 250V R:15 CLASS B
EC 1UF 160V 11*6.3 R:5
EC 47UF 63V 11*6.3 R:5
EC 22UF 250V 20*13 R:5
EC 470UF 16V 12.5*10 R:5
CC-CHIP 47NF K 25V /0603 X7R TAPE
CC-CHIP 10NF K 50V /0603 X7R
EC 10UF 63V 11*5 R:5
!!
!!
31
Component
M16130
7SZ129
031423R
056320-SS4
620167-AS
KX2110
J50208F
J50262F
J50212F
ZX6187F
7GA107R
60U535-AS
251487R
291101R
251478R
293113R
292114R
294122R
250333R
252112R
290475R
290223R
291104R
293271R
250475R
295110R
292114R
250470R
291226R
293234R
291226R
251478R
293113R
292475R
251478R
292114R
251105R
294233R
293113R
291104R
293113R
202109R
292114R
251105R
294122R
252112R
293478R
294476R
292114R
252113R
292153R
293685R
253155R
253115R
274107R
224112R
250470R
293234R
293113R
293334R
293113R
292114R
251105R
294122R
252112R
291337R
293478R
251478R
291104R
290335R
290107R
294235R
201470
294122R
293478R
293113R
294109R
272110R
273471R
251479R
201226R
292114R
224112R
250479R
203106R
274230R
200680R
274330R
500700-KD
272912
274363R
250100R
251475R
251230R
252482R
293478R
293113R
251116R
Definitions
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
InstPoint
C611
C612-C621
C622
C623
C624
C625
C626
C627
C628-C629
C630-C631
C632
C633
C634
C635
C636-C637
C639-C642
C644
C646
C647
C650
C651
C652
C653
C654
C655-C656
C657
C658
C659
C660
C661
C662
C664-C66
C668
C701
C702
C704-C705
C706-C708
C709
C710-C712
C713
C714
C920-C923
C940-C941
CAB1
D01
D102
D201
D202
D203
D401-D405
D406
D501
D504-D505
D506
D508-D511
D604
D605
D606-D609
D610
D611
D614
D615
D616-D618
D619
D620
D621-D701
D702-D074
D705-D07
D708
F103
FB102-FB103
FB501-FB502
FB601
FS601
IC01
IC101
IC201
IC301
IC401
IC402
IC501
IC601
IC601
IC602
IC603-IC604
IC606-IC607
IC609
L101-L102
L103
L104-L105
L106
L107-L108
L109-L110
L111
L112
L113
L114
L115
L116-L117
Object description
CC-CHIP 33NF K 50V /0603 X7R
CC-CHIP 47NF K 25V /0603 X7R TAPE
EC 1500UF 35V 20*13 R:5
CC-CHIP 100NF K 50V /0603 X7R
C-PEM 100NF J 250V R:10
C-PPM 330NF K 275V-AC R:22.5 CLASS-B
C-PEM 220NF K 275V-AC R:15 CLASS-B
C-PPM 33NF J 630V R:15
CC 470PF 2KV
EC 47UF 160V 21*13 R:5
CC-CHIP 56PF J 50V/0603 NPO TAPE
CC-CHIP 680PF J 0603 50V NPO
C-PEM 100NF J 250V R:10
CC-CHIP 1.5NF K 50V /0603 X7R TAPE
CC 220PF M 250VAC R:10 Y5U AH/NSA
CC 1NF K 1KV Y5P R:5
C-PEM 100NF J 250V R:10
CC-CHIP 100NF K 50V /0805 X7R
CC-CHIP 10NF K 50V /0603 X7R
CC-CHIP 47PF J 50V /0603 NPO TAPE
EC 100UF 400V 30*22 R:10
EC 47UF 25V 11*5 R:5
CC 220PF K 2KV Y5P R:5
CC 2.2NF M 250VAC Y5U R:10 AH/NSA
EC 1000UF 16V 20*10 R:5
CC-CHIP 56PF J 50V/0603 NPO TAPE
EC 1000UF 16V 20*10 R:5
EC 47UF 25V 11*5 R:5
EC 1000UF 16V 20*10 R:5
CC 100PF 500V NPO R:5
EC 1000UF 16V 20*10 R:5
EC 22UF 16V 11*5 R:5
EC 22UF 25V 11*5 R:5
EC 10UF 16V 5*3.5 R:5
CC-CHIP 100NF K 50V /0603 X7R
EC 10UF 250V 16*10 R:5
CC-CHIP 680PF J 0603 50V NPO
CC-CHIP 10PF J 50V /0603 NPO TAPE
CC 390PF J 50V SL R:5
CC 4.7NF K 1KV Z4V R:7.5
C-PEM 100NF J 250V R:10
CC 1NF K 50V Y5P R:5
C-PEM 47NF K 63V R:5
CABLE SINGLE ISO. L=90 BLUE
LED IR SIR563SB3F 23/940
DIODE 1N5819 SHOTH
DIODE 4148 MELF SOD-80C
DIODE 1N4148 52MM
JUMPER WIRE D=.6
DIODE 4148 MELF SOD-80C
LED L-513LR1D KIRM. L=25.4 (PARALIGHT)
DIODE 1N4148 52MM
DIODE 4148 MELF SOD-80C
JUMPER WIRE D=.6
DIODE BA157
DIODE 1N4148 52MM
DIODE 4148 MELF SOD-80C
DIODE RF2007
DIODE RGP30MS
DIODE 4148 MELF SOD-80C
DIODE RGP10J
DIODE RGP30D
DIODE RGP10J
DIODE BA157
DIODE 1N4148 52MM
DIODE 4148 MELF SOD-80C
DIODE 1N4148 52MM
DIODE 4148 MELF SOD-80C
DIODE 1N4007
SAW FILTER X6966M
FERRIT-CHIP 600R/100MHZ 200MA/0805
FERRIT HI1206N101R
FERRITE BEAD BI3857 5.7X3.6MM AXIAL
FUSE 3.15AT (215)
IC-CHIP S3C1840DA9/SMB91 T&R
IC VCTI-ECO-90DEG.-NO VD-FLASH-F1
IC-CHIP MC14052BDR2 G T&R
IC AN5277
IC-CHIP AT24C16AN 10SU2.7 TAPE&REEL
IR RECEIVER TSOP34838 SS1A
IC TDA8357 J N2
IC MC33269T G 0.8A LD TO220
INSULATER SILICON 19.5*12*.25
IC ICE1QS01
IC LM317LZRAG 0.1A TO92
IC-CHIP NCP1117DTARK G (DPAK) T&R TO252
IC TL431CLPRA G
COIL CHOKE 10UH LAN02 280MA/1R
COIL 10UH LAL02
COIL 10UH K (TAIYO) LAL03
COIL 10UH LAL02
COIL CHOKE 10UH LAN02 280MA/1R
COIL 10UH K (TAIYO) LAL03
COIL 10UH K AXIAL LAL04
COIL CHOKE 10UH LAN02 280MA/1R
COIL 4.7UH LAL03
COIL 4.7UH LAL04 52MM
COIL-CHIP 8.2UH K /0805
COIL 10UH LAL02
!!
!!
!!
!!
32
Component
293334R
293478R
253155R
294122R
274105R
274342R
274238R
203330R
201471R
251489R
290562R
291688R
274105R
292153R
201227R
202105R
274105R
294109R
293113R
290475R
252121R
251479R
201226R
202220R
253115R
290562R
253115R
251479R
253115R
201108R
253115R
251225R
251226
251105R
294122R
251109R
291688R
290107R
201390
222477R
274105R
202106R
273471R
500560-AS
303991R
303246R
303195R
302289R
500700-KD
303195R
303295R
302289R
303195R
500700-KD
300311R
302289R
303195R
303308R
303206R
303195R
303217R
303228R
303217R
300311R
302289R
303195R
302289R
303195R
302948R
056298R
055531R
055578R
055600R
054280R
452382R
453987R
453174R
453170R
452662R-2
452521R-1
452975R-1
453177R
50S313
452785R
453176R
453095R
451885R-1
053823R
053331R
053711R
053331R
053823R
053711R
053500R
053823R
053734R
053732R
053806R
053331R
Definitions
InstPoint
L203-L208
L301
L401-L403
L404
L405
L406
L502
L504
L601
L602
L603
L701
P602
PH601
Q01
Q102
R01
R102-R108
R109-R115
R119
R120
R121
R122-R123
R124
R125-R127
R128
R129
R130
R131-R132
R133
R201-R202
R203-R204
R205-R206
R207-R209
R210
R211
R213-R222
R225-R226
R228
R229-R230
R233-R236
R238-R257
R258
R259
R301-R302
R303-R304
R305-R306
R307
R308
R311
R312-R313
R317-R318
R319-R320
R323-R324
R325
R401
R402
R404-R407
R408-R409
R410-R413
R414-R416
R417-R418
R419
R420
R423-R424
R425
R427-R431
R432
R434
R435
R436-R437
R439-R441
R442-R444
R446
R448
R449
R450
R451
R452
R453
R454-R459
R461
R462
R463
R464
R466-R467
R468
R471
R472-R473
R475
R481
R501
R502
R504
R506
R508
R509-R510
R511
R513-R514
Object description
COIL-CHIP 10UH K 0805
COIL 10UH K (TAIYO) LAL03
COIL CHOKE 10UH LAN02 280MA/1R
COIL 10UH K (TAIYO) LAL03
COIL CHOKE 10UH LAN02 280MA/1R
COIL 4.7UH LAL03
JUMPER WIRE D=.6
COIL H-LIN 55UH NEOSID DIALTECH
LINE FILTRE 2*18MH R<0.7R /2416008010122
COIL CHOKE 50UH DIALTECH
COIL 47UH J LAL03
COIL- CHOKE 10UH R0814 14.1
R-VAR 10K V(2.5MM) 5*3
IC OPTOCOUPLER TCET1100/V310U27 VISHAY
CER.RESONATOR GSB455E
CRYSTAL 20.25MHZ 20PPM (106478)
RC-CHIP 0R /1206
RC-CHIP 10K J 1/16W /0603
RC-CHIP 100R J 1/16W /0603
RC-CHIP 33K J 1/16W /0603 TAPE
RC-CHIP 0R /0603 1.6*0.8 TAPE
RC-CHIP 1K J 1/16W /0603
CFR 220R J 1/4W 52MM
RC-CHIP 6.8K J 1/16W /0603
CFR 4.7K J 1/4W /6 26MM
RC-CHIP 100R J 1/16W /0603
CFR 100R J 1/4W 26MM
RC-CHIP 100R J 1/16W /0603
CFR 100R J 1/4W 26MM
RC-CHIP 0R /0805 2*1.25
RC-CHIP 18K J 1/16W /0603 TAPE
RC-CHIP 330R J 1/16W /0603 TAPE
RC-CHIP 560R J 1/16W/0603 TAPE
RC-CHIP 470R J 1/16W /0603 TAPE
CFR 10K J 1/4W /6 52MM
RC-CHIP 0R /0603 1.6*0.8 TAPE
RC-CHIP 75R J 1/16W /0603
RC-CHIP 100R J 1/16W /0603
CFR 100R J 1/4W 26MM
RC-CHIP 100R J 1/16W /0603
RC-CHIP 270R J 1/16W/0603 TAPE
RC-CHIP 1K J 1/16W /0603
CFR 4.7R J 1/4W /6 26MM
CFR 10K J 1/4W /6 52MM
RC-CHIP 330R J 1/16W /0603 TAPE
RC-CHIP 7.5K J 1/16W /0603
RC-CHIP 10K J 1/16W /0603
RC-CHIP 6.8K J 1/16W /0603
RC-CHIP 1K J 1/10W /0805
CFR 1K J 1/4W /6 52MM
RC-CHIP 3.3K J 1/16W /0603
RC-CHIP 56K J 1/16W /0603
RC-CHIP 4.7K J 1/16W /0603 TAPE
CFR 4.7R J 1/4W /6 26MM
RC-CHIP 18K J 1/10W /0805
RC-CHIP 470R J 1/16W /0603 TAPE
RC-CHIP 10K J 1/16W /0603
RC-CHIP 100R J 1/16W /0603
CFR 100R J 1/4W 26MM
RC-CHIP 100R J 1/16W /0603
RC-CHIP 270R J 1/16W/0603 TAPE
RC-CHIP 1K J 1/16W /0603
CFR 1K J 1/4W /6 52MM
CFR 10K J 1/4W /6 52MM
RC-CHIP 2.7K J 1/16W /0603
RC-CHIP 22R J 1/16W /0603 TAPE
RC-CHIP 3.3K J 1/16W /0603
RC-CHIP 180R J 1/16W /0603
RC-CHIP 22K J 1/16W /0603
CFR 22K J 1/4W 26MM
RC-CHIP 7.5K J 1/16W /0603
RC-CHIP 150R J 1/16W /0603
RC-CHIP 33R J 1/16W /0603 TAPE
RC-CHIP 100K J 1/16W /0603
CFR 10K J 1/4W /6 52MM
RC-CHIP 4.7K J 1/16W /0603 TAPE
CFR 10K J 1/4W /6 52MM
RC-CHIP 5.6K J 1/16W /0603 TAPE
RC-CHIP 47K J 1/16W /0603 TAPE
RC-CHIP 1.2K J 1/16W/0603 TAPE
RC-CHIP 100R J 1/16W /0603
RC-CHIP 4.7K J 1/16W /0603 TAPE
CFR 4.7K J 1/4W /6 26MM
RC-CHIP 220R J 1/16W/0603 TAPE
RC-CHIP 22R J 1/10W /0603
RC-CHIP 1.5K J 1/16W /0603 TAPE
RC-CHIP 1K J 1/16W /0603
CFR 150R J 1/4W 26MM
RC-CHIP 1.5K J 1/16W /0603 TAPE
RC-CHIP 680R J 1/16W /0603
RC-CHIP 15K J 1/16W /0603 TAPE
RC-CHIP 18K J 1/16W /0603 TAPE
RC-CHIP 220R J 1/16W/0603 TAPE
RC-CHIP 1K J 1/16W /0603
RM 10K J 1/2W 52MM
CFR 2.7K J 1/4W /6 52MM
RC-CHIP 5.6K J 1/10W /0805
RC-CHIP 560K J 1/16W /0603
RC-CHIP 10K J 1/16W /0603
!!
!!
33
Component
053804R
053711R
053823R
053711R
053823R
053734R
500700-KD
051591R-10
51828
053739R-10
053778R
053352R
133118R
452297R-2
056210R
056038R
179002R
173108R
171107R
173332R
179005R
172104R
101223R
172686R
102487R
171107R
101117R
171107R
101117R
179001R
173183R
171336R
171562R
171472R
103116R
179005R
170754R
171107R
101117R
171107R
171227R
172104R
109473R
103116R
171336R
172751R
173108R
172686R
172101R
102101R
172336R
173563R
172479R
109473R
173182
171472R
173108R
171107R
101117R
171107R
171227R
172104R
102101R
103116R
172276R
170221R
172336R
171184R
173229R
103234R
172751R
171154R
170333R
173114R
103116R
172479R
103116R
172567R
173478R
172125R
171107R
172479R
102487R
171224R
170225R
172154R
172104R
101163R
172154R
171683R
173153R
173183R
171224R
172104R
113114
102273R
172561R
174563
173108R
Definitions
See the "CPT Difference List", too
See the "CPT Difference List", too
InstPoint
R515
R516-R517
R521
R522
R523
R524
R525
R526
R527
R529
R531-R532
R533
R534
R537
R538-R542
R601-R602
R605
R606
R609
R611
R617
R618
R619
R620
R621
R627
R628
R629
R631
R631
R632
R634
R635
R636
R637
R638
R639
R640
R644
R645
R648
R649
R650
R651
R652
R654
R656-R658
R659
R663
R664
R665
R666
R666
R667
R702-R705
R706-R708
R709-R711
R712-R714
R715
R716-R718
R719
R720
R721
R722-R724
R725
R726-R727
R728
R729
R730-R732
R920-R921
R922-R923
R940-R941
R942-R943
SK202
SW401-SW403
SW601
T01
T102-T307
T401
T403-T501
T502
T504
T601-T603
T609
T701-T703
T704-T706
T707-T709
TH601
TR501
TR502
TR601
TU102
TUN-SC2
X203
X204
X301
X302
X401A
X404
Object description
CFR 2.7K J 1/4W /6 52MM
RM 3.9R J 1/2W /9 52MM
RW 4.7R J 7W R:5
RMF 0.22R J 1W
CFR 330R J 1/4W /6 52MM
CFR 1.5R J 1/2W /9
RMF 10R 1/4W
CFR 47K J 1/4W /6 26MM
CFR 470R J 1/2W /9 52MM
CFR 560R J 1/4W /6 52MM
RM 150K J 1/2W ' SAFETY'
CFR 0.47R J 1/2W /9 52MM
CFR 47R J 1/4W /6 52MM
RC-CHIP 56R J 1/16W /0603 TAPE
RC-CHIP 1.5K J 1/16W /0603 TAPE
RC-CHIP 10K J 1/16W /0603
RC-CHIP 1K J 1/16W /0603
CFR 1K J 1/4W /6 26MM
RC-CHIP 1K J 1/16W /0603
RC-CHIP 2.7K J 1/16W /0603
RC-CHIP 22K J 1/16W /0603
RC-CHIP 47K J 1/16W /0603 TAPE
RM 1M J .5W 52MM SAFETY
PTC 9R/2 PIN - 3 CYCLE BOX TYPE
RMO 68K J 2W 73MM
CFR 47K J 1/4W /6 26MM
RM 115K %1 1/4W
CFR 2.2K J 1/4W /6 26MM
RMO 47K 2W
RMO 47K J 1W
RC-CHIP 12K J 1/16W /0603 TAPE
RC-CHIP 0R /0603 1.6*0.8 TAPE
RW 2.7R K 5W R:15 MM
RM 1M J 1W 52MM
RC-CHIP 68K J 1/16W /0603
CFR 47R J 1/4W /6 52MM
CFR 120R J 1/4W 52MM
RC-CHIP 33R J 1/16W /0603 TAPE
RM 4.7M J 1/2W 52MM 'SAFETY '
CFR 47R J 1/4W /6 52MM
RC-CHIP 820R J 1/16W /0603 TAPE
RNF 0.1R J 0.4W (UFLB) 52MM
RC-CHIP 2.7K %1 1/16W /0603
RC-CHIP 39K J 1/16W /0603 TAPE
RM 150K J 1/2W ' SAFETY'
RC-CHIP 1.3K %1 1/16W/0603 TAPE
RC-CHIP 240R %1 1/16W /0603 TAPE
RC-CHIP 390R %1 1/16W/0603 TAPE
RC-CHIP 365R %1 1/16W /0603 TAPE
RC-CHIP 390R %1 1/16W/0603 TAPE
RC-CHIP 470R %1 1/16W /0603 TAPE
RC-CHIP 120R J 1/10W /0805
RC-CHIP 120R %1 1/16W /0805
RC-CHIP 820R %1 1/16W /0603 TAPE
RC-CHIP 1K J 1/16W /0603
CFR 1K J 1/2W /6 52MM
RC-CHIP 220R J 1/16W/0603 TAPE
RC-CHIP 3.3K J 1/16W /0603
CFR 220R J 1/4W 26MM
RMO 12K J 2W
CFR 330K J 1/4W /6 52MM
CFR 47K J 1/4W /6 26MM
CFR 1M J 1/4W /6 26MM
RC-CHIP 22R J 1/10W /0603
CFR 1.5K J 1/2W /9 52MM
CFR 100R J 1/4W 26MM
RC-CHIP 100R J 1/16W /0603
CFR 470K J 1/4W /6 26MM
RC-CHIP 470R J 1/16W /0603 TAPE
CFR 75R J 1/4W /6 26MM
CFR 470R J 1/4W /6 26MM
CFR 180R J 1/2W (A) 52MM
CFR 390R J 1/4W /6 26MM
SCART SOKET HR-DM2441S-O
TACT SW LONG STEN
ON/OFF SWITCH BK98
TRN BC337-25
TRN-CHIP BC848BLT1G SOT23
TRN-CHIP BC818-215 SOT23
TRN-CHIP BC848BLT1G SOT23
TRN BC639
TRN. 2SD2586
TRN-CHIP BC848BLT1G SOT23
TRN 2SK3567 TO220SIS
TRN-CHIP BC848BLT1G SOT23
TRN BF421
TRN 2SC3619
THRYSTOR MCR22-8RL1G
TRANSFORMER HORIZONTAL DRIVE E1
FBT 20/21 EL/ 1142.5162 25KV
SMT 20/21 EL/ 2084.0130 23V
TUNER PS ASIMETRIK ENV57DA5G3R(SEC LL IY
METAL FOR EMC
CONN.HOUSING X2003 RED
CONN.HOUSING X2003 BLACK
CONN.HOUSING X2004 GREY
CONN.HOUSING X2003 GREY
CABLE WITH HOLDER 5P L=375 CRT/CHAS
CONN.HOUSING 2.5TMK 2104 GRI
!!
!!
!!
!!
!!
!!
!!
!!
34
Component
102273R
111396R
129487R
119224
101331R
109150R
120118R
103484R
101471R
101562R
114151R
109472R
100473R
170560R
172154R
173108R
172104R
102141R
172104R
172276R
173229R
173478R
115110R
154234R
113684R
103484R
114115R
102228R
113479
113475R
173124R
179005R
129272R
115103R
173685
100473R
101124R
170333R
115470R
100473R
171824R
119109R
172278R
173394R
114151R
172131R
171241R
171392R
171363R
171392R
171479R
171122
171128R
171825R
172104R
102105R
171224R
172336R
101236R
113121R
104332R
103484R
105110R
170225R
102159R
101117R
171107R
104470R
171472R
100751R
101494R
101184R
101396R
31197
010860R
010861R
401047R
401141R
401193R
401141R
400240R
401506R
401141R
401512R
401141R
401366R
400891R
410026R
051839R
040146-EL1
050150R-E1
7RZ136RPS4
KX1325R
31857
31856
31858
31854
ZX8558-AS
31989
Definitions
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
See the "CPT Difference List", too
InstPoint
X501
X502
X503
X601
X602
X703
X920
X921
X922
X923
X940
ZD501
ZD502
ZD503
ZD601
ZD602
Object description
CONN.HOUSING 2'LI GREY
CON.HOUSING LOCKED 5/4
CABLE WITH HOLDER 3+1P L=430 CRT/SASI K1
CON.HOUSING 2P MALE
CON.HOUSING 2P MALE TPK75(POW)12.6 RED
CRT SOCKET NARROW INCHANG
CABLE HARNESS 3+3P L=400 HP.MOD.
KONN. CINCH ........... YELLOW HOR.14.1
KONN. CINCH ........... RED HOR.14.1
KONN. CINCH ........ WHITE HOR.14.1
CABLE HARNESS 3P L=360 HP.MOD.
DIODE Z. BZX55C 15V
DIODE Z. BZX55C33 52MM
DIODE Z. BZX55C8V2 26MM
DIODE Z.TZMB9V1
DIODE Z. BZX55C5V1
!
!
!!
!!
!!
35
Component
31850
31777
KX1553R
31675
31797
31532
7KY537-AS
031165R
031164R
031163R
7XY517-AS
303826R
302318R
302294R
303454R
302298R
Definitions
See the "CPT Difference List", too
See the "CPT Difference List", too
1
GND
VSUP8.0AU
VSUP5.0BE
C404
10n
C107
1n
C109
1n
16
C139
47p
L115
8.2uH
19
RESETQ
BOUT
VRD
XREF
21
VSUP3.3DIG
79
78
C439
0R (PIP : 22p)
FBLpip
C413
1n
Rpip
76
75
VSUP3.3BE
GND
GND
GND
GND
R479
1k
73
R418
1k
68
SAFETY
AUDIO SEL
HFLB
SC1 F IN
HOUT
SC1 B IN
VPROT
C127
100n
SC1 G IN
C142
47p
32
SC1 R IN
C150
47p
33
C151
47p
34
35
36
C120
100n
R114
100R
DVD
C149
47p
100R
C124
100n
C144
47n
38
C147
47p
3.3V
1
2
3
4
5
6
7
8
1
2
3
4
1.8V_STB
L114
SDA
SCL
5
6
7
X102
CON8
41
42
P20/DFVBL
KB
FR AV CHR
STATUS 3
FR AV Y
STATUS 2
STATUS 1
PIP CVBS
40
100R
R116
P21/PWMV
SC2 CHR
LED
SC1 CVBS OUT
IR
SC2 CVBS OUT
ST-BY
PIP CVBS OUT
MUTE
R406
100R
62
R407
VSUP1.8FE
VSUP3.3FE
C135
100u/16V
3.3V_DVD
44
C128
100n
GND
GND
R401
470R
R420
R481
4.7K
10K
59
55
dvd
54
KB
C416
1n
53
KB2
52
STATUS2
48
R455
100R
47
R462
4.7k
R409
100R
R452
47k
22k
STATUS_1
C421
1n
3.3V_STB
L405
45
R605
1k
R628
table
R651
39k
C654
2.2n/250V
4
1
2
3
4
D406
LED
R472
1.5k
R475
2
VOUT1
Standby
11
12
VCC
9
10
8
GND
MUTE
VOUT2
7
NC
VIN2
6
5
GND
Rip. Filt.
4
ZD401
5.1V
680R
3.3V_STB
R471
SW401
R473
150R
D604
1N4148
IC609
TL431C
C657 C602
47n
56p
R650
2.7k %1
47n
T601
BC848B
C607
10n
C667
22u/16V
C649
10n
C661
C604
10n
C623
100n
R653
NS
T602
BC848B
D605
1N4148
FB603 CON5
12V
R525
R609
1K
1k
T603
BC848B
R602
10k
R601
10k
C605
10n
D507
table
C517
10n/63V
R529
560R
C524 C513
table
T504
2SD2586
5
C665
22u/16V
C515
4.7u/50V
1
2
180V
R720
47k
CRT MODUL
VOL+
D501
1N4148
R614
3.3k
R604
10k
3.3V
47n
C621
ST_BY
8V
R603
10k
5
C522
330n/250V
D510
R519
table
2
table
D502
1N4148
T503
table
C521
2.2uF/63V
R536
*0.1R
8.2uH
R518
R535
*0.1R
4
C525
L501
EW_DRIVE
C609
10u/16V
9
C672
10n
R530
100K
R615
3.3k
4
table
D506
RGP30K
C523
table
C526
table
L503
table
6
1
C707
680P
D511
C532
22u/250V
R538
C531
47u/63V 1.5K
BA157
R542
33V
1.5K
D509
7
R728
CRT
390-470p
R703
1k
T706
BF421
R713
3.3k
R710
220R
R717
T707
2SC3334 12k 2W
R724
22R
R732
470R
R708
1K
CRT
CRT
D707
1N4148
R717A
X703
CRT CON
CRT
CRT
12k 2W
C712
390-470p
T703
BC848
R711
220R
R725
1.5K 1/2W
C710
R718A
12k 2W
R715
220R
R707
1K
X702
1
2
CRT
180V
R714
3.3k
CRT
L701
10uH
D705
1N4148
R705
1k
C709
100pF
SMPS
CAB701
AQUA
AQUA701
C705
10u/250V
C714
100n/275V
R729
330k
R733
47R
4
CON4-3KIL
ZD502
33V
12V_VERT
CRT
CRT
C533
470u/16V
BA157
12V_DVD
D512 R540
LL4148 47k
R539
47k
ZD504
8V2
C534
22uF/50V
DST E1
R709
220R
D708
1N4007
CRT
D706
1N4148
R718
T708
2SC3334 12k 2W
R721
1M
C703
22n/63V
1K
C713
4.7n/1kV
100R
C708
680P
45V_VERT
3
2
D704
1N4148
R723
22R
470R
C704
10u/250V
R706
R731
T705
BF421
T701
BC848
R727
8V
390-470p
C711
R704
1k
D703
1N4148
CRT
EMC
CRT
R716
T709
2SC3334 12k 2W
R712
3.3k
22R
C706
680P
8V
R522
table
BA157
D510A
RED
4
C514
1n
2
C518
220n/100V
8
R722
2
X503
1
ST_BY
R664
390R%1
R504
1k
G2
11
10
3.3k
GREEN
R719
330k
T704
BF421
D701
1N4148
R716A
12k 2W
T702
BC848
100R
FOCUS
2
6
R726
100R
1
X502
R521
table
BLUE
3
1N4148
C503
100n
180V
D702
1N4148
7
8V
1k
C701
10u/16V
D504
J503
JUMP
R730
470R
R702
8V
T501
BC858B
BA157
C666
22u/16V
T604
BC848B
HORIZONTAL YOKE
R520
table
115V
C504
47n
R508
2.7k
table
C520
NS
T502
BC639
R526
47K
EHT
R506
10k
L504
table
C502
470p/500V
L502
R534
120R
4
table
R617
22k
R618
47k
SELECT
8V
R537
56R
R502
470R
R527
470R
2
3
C527
table
D508
BA157
3
C620
47n
C671
22uF/10V
R658
240R %1
VS
OUT
5
C530
1u/160V
C528
220pF/
2KV
DRIVERE1
R666
120R %1
R616
C668
C615
22u/25V 47n
R611
2.7k
R606
1
C512
47u/25V
150k
R533
0.47R
TR501
T605
R663
365R %1 BC848B
ADJ
150k
ZD503
8V2
R501
18k
5V
IC606
NCP1117DTARK
IN OUT
R612
3.3k
68p/500V
C516
22nF/25V
1
240R %1
8V
TR502
1
R532
2
4
2
R668
R531
1
3
C648
10n
C519
HFLB
8V
1
HSYNC
3
H_DRIVE
ADJ
47n
IC402
TSOP1838
X701A
2
4
22R
C616
R468
2.7k
GND
VOL-
2
1
IN
IC605 R661
C619
TL 431 2.7k %1
ADJ
C670
47n
R660 1000u/16V
2.7k %1
R608
390R %1
IC607
NCP1117DTARK
IN OUT
6.5V
SW403
PROTECTION
HS501
DVD_POWER
TH601
MCR22-8
C440
47u/16V
1.5k
SW402
HEATSINK
X603
5
5V_DVD
100p/500V
P602
10k
D613
LL4148
4
C664
22u/16V
C610
HS602
SERVICE
R470
1k
2.2k
12V_DVD
R652
150K ½ W
R629
2.2K %1
47R
R648
820
ZD602
6.2V
SMPS HEATSINK
3
3
ZD601
9V1
X403
DVD_COM
C702
100n
5
OPT1
X501
VYOKE
6.5V
R626
4
1
2
R644
4.7M 0.5W
5
2
R610
1k
D612
LL4148
C603
10n
D619
BA157
C622
1500u/35V
C611
33n
C608
10u/63V
C606
10n
FB602
T610
20NE06
8V
R656
240R %1
C612
47n
C659
R645
PH601
TCET1100
3
R667
820R %1
R665
470R %1
T608
BC848
R625
10k
3
4
2
1
R633
6.8k
FB402
1n
ZD402
3V6
3
1
C614
47n
D615
RGP30D
R646
0.22R
2
3
1
ADJ
24V
1
C638
100p
C511
47n/63V
FB502
HI1206N101R
GND
D603
1N4148
R659
390R %1
ADJ
C618
47n
R657
240R %1 C617
47n
47uH
R637 C652
47u/50V
27R
R627
47k
1n/100V
GND
14
2.7k
HT
13
8
R524
1.5R 1/2 W
C510
R515
9
BLUE
6
FEEDB
IC501
TDA8357
11
LL4148
C647
10n
table
12
C646
100n
R516
table
R517
R413
100R
4
27R
ICE1QS01
6.5V
C632
56p
IC603
LM317LZRA
IN OUT
R654
1.3k %1
L603
R412
100R
IC401
24C16
4
HT
5
D621
R523
330R 1/2W
OUTB
8V
3.3V_DVD
IC608
NCP1117DTARK
OUT
D617
C656
1000u/16V
D611
LL4148
R638
R613
3.3k
DVD D616 : SB540
C655 :2200u/16v
47u/25V
6
Stand-by
ADJ
0.22R RGP15J
7
3.3V_STB
IC604
LM317LZRA
IN OUT
C662 C613
47u/35V 47n
1000u/16V
R647
11
7
10
OFC
8
6.5V
RGP10J
C655
1000u/16V
1.8V_STB
IC601
MC33269DT
IN OUT
C660
12V
C629
470p/2kV
OUTA
9
SRC
2
VGND
5
GND
T609
FQPF3N60FP
5
RED
4
C635
1.5n
RZI
15
12
C650
47p
R512
10k
8
R634
0R
OUT
0.1R
R639
XXX
R503
10k
C445
10p
7
R632
12K
P601
2.2k
PCS
R624
47k
C631
47u/160V
D616
R649
4
R513
10k
GUARD
G2
3
VCC
C630
47u/160V
R631
47K
D618
RGP10J
D614
RGP10J
8
VPROT
6
2
NC
D610
RGP30MS
X402
T607
3.3V_STB BC848
HS603
1000u/16V
1n/1kV
120
IC602
1
R640
33R
D620
LL4148
C645
C633
680p
TR601
SMPS_K1
17
C653
220p/2kV
C643
R514
10k
C509
100n/50V
X406
SMPS HEATSINK
L602
50uH
C658
C651
68u/400V
R636
1M 1W
R621
68k 1.5W
LL4148
6
X404
CON4
FB401
C420
C419
1n
3.3V_STB
C642
1n/1kV
D608 D609
RF2007 RF2007
FS601
3.15A
X601
MAINS
1n/1kV
C639
1n/1kV
C637
220p /1KV
VFB
FB501
HI1206N101R
KEY
1
C636
220p /1KV
3
C634
100n
INB
R411
100R
R417
1K
ST_BY
MUTE_L
10uH
C431
100u/16V
D505
n.c.
C644
C
R431
3.3k
C409
10n
46
C505
100u/35V
3.3V_STB
C424
10u/16V
R410
100R
STATUS_2 C441
100p
R430
3.3k
3.3V_STB
C641
C640
1n/1kV
2
C446
10p
IR
ST_BY
C508
100n/50V
GREEN
2
SW601
POWER SWITCH
R635
2.7R 5W
2
C438
47n
T406
BC848B
R435
2.2k
C428
100n
C507
10n %10
3
G1
1
4
LINE FILTER
FB601
C627
FB
33n/630V
1
C410
10n
R464
49
R510
5.6K %1
R460
100R
ZD403
3V6
115V
D606
D607
RF2007 RF2007
VIN1
4.7uH
STATUS1
C408
10n
R463
220R
R467
1.5k
R466
1.5k
R408
100R
50
C506
10n %10
VP
L406
R459
100R
C418
1n
R509
5.6K %1
VERTQ
R446
4.7k
R458
100R
C417
1n
INA
45V_VERT
R457
100R
56
DVD KEY
1
S14K385
3
12V_VERT
R456
100R
57
ZD501
15V
table
1
VERT
C601
47u/16V
C628
470p/2kV
R619
470k 1/2W
R511
VPROT
R454
100R
58
R622
47R
RELAY
T606
BC858
220n/275V
table
4.7k
T405
BC848B
R447
4.7K
NC
L601
C625
2
4.7k
T404
BC848B
R445
4.7k
H_DRIVE
R623
390k
C626
R630
1
3.3V_STB
2.7K
R461
D402
1N4148
R465
D602
1N4148
D601
1N4148
PTC1
CAB501
SCL
3.3V
R449
D401
1N4148
R402
10K
C442 L404
10uH
33p
Bpip
1
DEGAUSS
220V AC INPUT
Gpip
JUMPER
Rpip
FBLpip
12V
RL601
2
SENSE
NC
HFLB
5V_DVD
1W OPT.
R620
C624
100n/250V
R450
10K 1/4 W CF
SDA
3.3V
R424
VSTI-F ver
C412
1n
5V
R448
10K 1/4 W CF
EKRAN VCTI
X602
2
3
4
R429
3.3K
T403 R477
BC848B 0R
R419
1K
R428
3.3K
R451
5.6K
60
51
5V
VSTI-F ver
R476
0R
C411
1n
61
100R
43
T410
BC858B
63
4.7uH
Audio_PIP
VSYNC
33V
HSYNC
X101
CON8
8
R132
SC1 CVBS IN
SC3 CVBS
39
100R
R131
SCL
SC2 Y
37
R115
SDA
3.3V
C422
10u/16V
8V
VSYNC
64
L403
10uH
1
GNDDAC
10uH
C430
100u/16V
65
2
C126
100n
31
C148
47p
C125
100n
C123
100n
5
3.3V_STB
66
4
R130
100R
FR_AV_Y
10uH
C423
10u/16V
C402
22n
67
3
30
C141
47p
Y_SC2
FR_AV_C
C426
100n
L401
2
C118
100n
CH_SC2
C146
47p
C401
4.7u/16V
1
C117
100n
G/Y
V_SC1
6
70
69
6
29
B/Cb
R107
T304
BC858B
C304
1n
5
VSUP3.3DAC
AUDIO SEL
C140
47p
C145
47p
C122
100n
T307
BC858B
R311
71
SDA
R128
100R
F_BLANK_SCART
R/C/Cr
R302
330R
GND
27
R108
75R
Right
HEADPHONE
2
GND
VSUP3.3IO
25
XTALL1
20.25Mhz
Q102
26
XTALL2
C154
22p
C155
22p
75R
C121
100n
R129
100R
R313
3.3k
72
100R
R106
75R
X405
SVM OUT
1
R478
1k
74
1
C311
100u/16V
Bpip
Left
2
C307
1n
8V'
4
VSUP1.8DIG
28
R104
8V'
SVM
C415
1n
X302
3
C306
1n
Gpip
5V
L301
10uH
C313
100u/16V
C312
100u/16V
T305
BC858B
C305
1n
8
24
C116
100n
R126
3.9K
D102
75R
SCHOTTKY
R105
75R
C315
47n
T306
BC858B
1k
C414
1n
8V
C301
10n
R301
330R
L402
23
R127
47K
R323
4.7R 1/2W
3.3V
L111
T103
BC848B
GOUT
VSUP5.0IF
22
8V
R103
10K
ROUT
IFIN+
C321
1n/35V
100n
EMC
R320
4.7k
8V'
R312
3.3k
C115
100n
10uH
C132
100u/16V
8V'
R434
22K
77
MMZ2012Y601B
4.7uH
C134
1.8V_STB 100u/16V
T102
BC848B R125
3.9K
IFIN-
VSUP5.0FE
20
C114 MMZ2012Y601B
100n
FB103
L113
R102
10K
R453
1.2k
EW
FB102
10uH
C133
100u/16V
3.3V
SVMOUT
C330
C434
33n
1k
18
C113
100n
L110
8V
80
R403
100R
68n
7
10uH
C102
47u/16V
BIN
VREFIF
17
5V
R432
180R
C119
100n
IFINIFIN+
5V
GIN
TAGC
15
C161
1u/16V
L109
RIN
SIF/AIN1R
14
C110
1n
81
C433
R438
6.8k
SCL
100R
R427
3.3k
Left
1
R305
10k
EW_DRIVE
82
2
R324
4,7R 1/4W
LOUDSPEAKER
R321
2.2K 1/4W
C302
1n
T301
BC848B
MUTE_L
83
VCC
R113
AIN1L
R322
2.2K 1/4W
C326
1500u/35V
C308
10u/16V
R314
22k
C319
1n/35V
R405
100R
MODE_WC
L112
10uH
FBIN
R437
7.5K
R433
22K
Right
3
C320
1n/35V
VERT
84
R308
12
SC1_IN_R 13
C106
1n
GNDM
AIN2R
R414
270R
85
E2
5
L105
10uH
ABC
CUT SENSE
C325
68n/50V
R319
4.7k
C329
100n
6.5V
R304
10k
E1
L108
3
C131
100u/16V
C103
10n
WDRV
56K
33R
C317
470n
C310
100n
R443
VERTQ
E0
C156
100p
EW
AOUT1R
C323
1.5n/50V
X301
4
C327
1000u/16V
R306
C324
10k
24V 1.5n/50V
C328
1000u/16V
R318
R404
100R
R436
7.5K
3
DVD
F103
X6966M
SC1_IN_L
10uH
R124
6.8K
5V
AOUT1L
AIN3L/AOUT2L
11
C108
1n
10uH
1
2
T209
BC848
VERT-
9
AIN3R/AOUT2R
C143
47p
10
AIN2L
L117
L107
10uH
C162
1n
VERT+
SPEAKERR
C318
1n/35V
T409
BC858B
D405
1N4148
2
F102
table
SPEAKERL
C138
47p
L106
10uH
R119
33k
C158
27n
7
8
L116
10uH
0R
CON3
6
C136
47p
L103
10uH
C157
100p
86
C322
100u/35V
C437
330p
R441
150R
87
C406
33n
C104
1n
C137
47p
C163
1n
TEST
C407
33n
5
SC1_OUT_R
R211
FR_AV_Y
4
C105
1n
R303
10k
1
IF2
IF1
11
10
table
C160
4.7u/63V
VREFAU
R307
2.2k
C316
470n
C309
100n
56K
1
19
21
+33V
n.c.
9
+5V
SDA
+5V
8
7
SCL
5
n.c.
AGC
AS
4
3
2
1
6
C159
C153
22p
SCL
SDA
FR_AV_C
BLUE
1
88
C405
10n
10uH
R121
1k
R415
270R
33R
GND
3
SC1_OUT_L
L102
R110
100R
C152
22p
L101
10uH
33V
R317
330p
2
5
8
9
10
11
14 12
15 13
16
INH
VEE
VSS
VDD
C252
100p
C253
100p
2
R260
22K
R223
75R
C244
10u/16V
1
CON3
X204
1
3
CON6
ZD210
5V1
C241
4.7n
T208
BC848
FB201
6
C129
3.3u/16V
4
R247
100R
1k
12
7
1
2
3
4
5
8V
C248
1n
C209
4.7u/16V
1k
C225
220p
R261
22K
4
2
R257
C210
4.7u/16V
R244
3
1
1k
4.7u/16V
C236
4.7n
DVD_MUTE
2
2
GND2
GND1
C206
4.7u/16V
C246
1n
C247 R256 X203
3
1n
100R
C220
220p
X202
1
R227
220R
1k
C112
100n
R122
220R
13
R416
270R
C435
C429
100u/16V
IC101
VCTI
C130
100u/16V
HS301
IC301
AN5277
T408
BC858B
R442
C111
100n
14
GND3
R109
X206
OPTO
3
C217
22n
C205
C202
4.7u/16V
T407
BC858B
R444
33R
R440
ST_BY
ST_BY
R123
220R
15
GND4
TU102
R228
100R
R246
2.2k
TO LOADER
8V
TUNER
R237
R426
10R
T402
BC848B
150R
2
8V
C436
330p
R422
10K
RIGHT
1k
2
150R
C403
47u/16V
C432
100n/16V
LEFT
X2
1
10n
R439
X1
R241
C232
10n
C214
22n
X407
C243
13
X
HEATSINK
D404
1N4148
R421
4.7R
T401
BC818
C239
4.7n
R209
470R
R204
330R
R120
R224
180R
R212
180R
X0
T203
BC848B
C227
47u/16V
R232
270R
5
R425
22R
C208
4.7u/16V
1k
C223
220p
D403
1N4148
C240
4.7n
L104
10uH
6
15
4
X205
CINCH
14
3
1k
X3
12
2
R222
75R
R423
2.7k
C207
4.7u/16V
R242
C224
220p
Y2
11
R245
2.2k
C231
10n
R220
75R
R221
75R
Y1
7
X201
to DVR/LINE OUT C213
1
22n
R214
75R
R240
1k
C226
47u/16V
R231
270R
8V
X401A
CRT
5V
75R
R218
T205
BC848B
3
Y
C230
47u/16V
C251
10n/50V
8V
20
Y0
2
T204
BC848B
5V"
C219
22n
47u/16V
C235
10n
R236
270R
R243
T207
BC858B
R206
560R
R202
18k
C250
220n
D202
1N4148
Y3
1
5
T202
BC848B
9
B
4
SCART 2
R208
470R
R258
4.7R
A 10
IC201
MC14052B
C237
4.7n
R215
75R
R203
330R
5V"
C249
10u/16V
C203
4.7u/16V
R239
1k
C221
220p
470R
D203
1N4148
5V
C238
4.7n
8
D201
1N4148
R216
75R
21
R207
R217
75R
SC1+SC2
R254
0R
0R
8
10
18
75R
C222
220p
C212
220p/25V
R252
0R
R253
0R
C204
4.7u/16V
R238
1k
19
R213
20
T201
BC848B
13 11
T206
BC858B
16
R201
18k
C234
10n
C216
22n
9
C211
220p/25V
14 12
R205
560R
17 15
10k
5V"
C228
47u/16V
100R
R219
75R
17
5
6
7
R210
STATUS_2
R234
270R
10k
R251
0R
SC1+FAV
R226
100R
7
R259
STATUS_1
C229
270R
C218
22n
18
C233
10n
R235
R229
100R
R230
6
C242
47uF/16V
22n
L204
1OuH
4
R233
270R
16
3
2
1
R225
100R C215
RED
L207
1OuH
L208
1OuH
GREEN
SK201
SCART 1
Audio_PIP
L203
1OuH
SK202
2
KX1.820
K1-K5 CTV CHASSIS
T505
BC327
Components designated by the safety symbol should only be replaced by original parts produced and proofed by the manufacturer.
R541
10k
Sicherheitsbautelle im Sinn der sicherheitsbestimmung. Diese Teile durfen nur durch Originalteile ersetzt werden.
T506
BC848
Contrassegno di sicurezza. I componenti devono, corrispondere a ricambi originali e devono essere montati a regola d’arte.
DVD_POWER
21"SLIM CRT
TR
DST_C8_EK
Subject to change without notice