Download Sioux Tools 5265 User's Manual

Form # Z409
Date 2-02lA
Model 5265
5" Dia. Angle Sander
IMPORTANT
Read these instructions carefully before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.
SAFETY MESSAGES
Personal Safety Equipment
- Safety Glasses
Use - Safety Gloves
Use - Safety Boots
YES
YES
Use
YES
YES
Use
Use
- Breathing Masks
- Ear Protectors
A
WARNING
0
Always Read Instructions Before
Using Power Tools
@
Always Wear Safety Goggles
@
Wear Hearing Protection
W^
Avoid Prolonged Exposure
TOVibration
Operator Instructions
Includes:
Safetv Rules
Use
Work Stations
Putting Into Service
Operating
Dismantling and Assembly.
ores seen
Safety rules when using a 5265 Sander
-
working attachment fitted to the tool.
Do not use as a grinder.
- Before using the tool, make sure that a shut off device
Do not use polystyrene pads.
has been fitted to the supply line and the positionis known
Use accessories rated above 7,000 RPM.
and easily accessible so that the air supply to the tool can
Prolonged exposure to vibration may cause injury.
be shut off in an emergency.
Read all instructionsbefore using this tool. All operators must
- Check hose and fittings regularly for wear.
be fully trained in its use and aware of these safety rules.
- Take care against entanglement of the moving parts of
- Do not exceed the maximum working air pressure.
the tool with clothing, hair, ties, cleaning rags, rings,
Use personal protection equipment as recommended.
jewelry, watches, bracelets, etc.This could cause the body
- Some dust created by power sanding, sawing, grinding,
or parts of the body to be drawn towards and in contact
drilling, and other construction activities contains
with the moving parts of the tool and could be very
chemicals known to cause cancer, birth defects and other
dangerous.
reproductive harm.
- It is expected that users will adopt safe working practices
- Use compressedair only at the recommended conditions.
and observe all local, regional or country legal requirements
- If the tool appears to malfunction, remove from use
when installing, using or maintaining the tool.
immediately and arrange for service and repair. If it is not
- Take care that the exhaust air does not point towards any
practical to remove tool from service, then shut off the air
other person or material or substance that could be
supply to the tool and write or have written a warning
contaminated by oil droplets. When first lubricating a tool
note and attach it to the tool.
or if the tool exhaust has a high oil content, do not allow
- If tool is to be used with a balancer or other suspension
the exhaust air to come near very hot surfaces or flames.
device, ensure that the tool is firmly attached to the
- Never lay the tool down until the working attachment has
suspension/support device.
stopped moving.
- When operating the tool, always keep the body and
- When the tool is not in use, shut off the air supply and
particularly the hands away from the working attachment
press throttle triggerllever to drain the supply line. If the
fixed to the tool.
tool is not to be used for a period of time, first lubricate,
- The tool is not electrically insulated. Never use the tool if
disconnect from air supply and store in a dry average room
there is any chance of coming into contact with live
temperature environment.
electricity.
- If the tool is passed from one user to a new or inexperiAlways when using the tool, adopt a firm footing andlor
enced user, make sure these instructions are available to
position and grip the tool sufficiently only to overcome
be passed with the tool.
any reaction forces that may result from the tool doing
work. Do not overgrip.
- Use only correct spare parts for mainTake Air From Top
tenance and repair. Do not improvise
a
or make temporary repairs. Major
Low Spot To
Trap Water
servicing and repairs should only be
with Sufficient Capacity
carried out by persons trained to do so.
11 11
11
To Maintain Recommended
- Do not lock, tape, wire, etc. the'On/Off'
Working Pressure At
11 11
valve in 'On' position. The throttle
Each Tool Outlet
Easy To Reach And
Air Tool
Operate. Shut Oft Valve
trigger/ lever, etc. must always be free
to return to the 'Off' position when
Drain Daily
released.
- Always shut off the air supply to the tool
\
Filter Lubricator
and press the 'On/Offl valve to exhaust
-
-
7
-
L
the air from the feed hose before
fitting, removing or adjusting the
Recommended Air Supply System
Page No 1
Figure 1