Download SIIG 04-0476A User's Manual

SATA-to-IDE Adapter
Quick Installation Guide
Introducing the SATA-to-IDE Adapter
The SATA-to-IDE Adapter allows you to connect existing
Ultra ATA 150/133/100/66 hard disk drive and ATAPI
devices to the latest Serial ATA host adapter.
Features and Benefits
•
•
•
•
•
•
•
•
Quickly converts older IDE/Ultra DMA devices for
use with newer Serial ATA controllers
L-shape compact design to reduce interference with
other devices
Connects directly to an IDE drive — no expansion
slot required
Compliant with Serial ATA 1.0a specification
Supports ATA/ATAPI Ultra DMA data transfer
rates up to 150MB/s
Compliant with ATA/ATAPI PIO modes 0 to 4
Connects large Ultra ATA 133/100/66 hard disks to
the latest Serial ATA hosts
Works with ATAPI optical storage devices such as
CD-ROM, CD-RW, DVD-ROM and DVD-RW (up to
16x)
Serial Number Sticker
For future product return or exchange, this serial number
is required. Please keep it for your reference.
04-0476A
1
System Requirements
•
•
Pentium ® or equivalent PC with an available
Serial ATA port
Windows ® 2000/XP (32-/64-bit)/Server 2003
(32-/64-bit)/Vista (32-/64-bit)
Package Contents
•
•
•
•
•
SATA-to-IDE Adapter
SATA data cable
"Y" split power cable
Shielding sponge
Quick Installation Guide
Board Layout
Power supply connector
SATA
connector
IDE connector
Figure 1: Layout
2
Hardware Installation
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1.
2.
3.
Turn OFF the power to your computer.
Unplug the power cord and remove your computer's
cover.
Attach the Isolation sponge to the SATA-to-IDE
Adapter, refer to figure 2 and 3. This step is optional.
Sponge
Figure 2: Before
sponge
4.
Figure 3: After
attaching sponge
Connect the SATA-to-IDE Adapter to the Ultra ATA/
ATAPI device, refer to figure 4 and 5.
Figure 4
Figure 5
3
5.
Connect the SATA data cable to the adapter, refer to
figure 6 and 7.
Figure 6
6.
Connect the "Y" split power cable to the adapter,
refer to figure 8 and 9.
Figure 8
7.
4
Figure 7
Figure 9
Connect the other end of the SATA data cable to the
SATA port on the SATA host adapter or
motherboard.
8.
Connect the "Y" split power connector to power the
IDE drive, refer to figure 10.
Figure 10
9.
Connect the other end of the “Y” split power cable
to the system power source.
10. The hardware installation is completed now.
11. Replace the computer cover and reconnect the
power cord.
Windows Driver Installation
No driver installation needed.
5
Blank Page
6
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
to your questions could be just a few clicks away. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIG offers a lifetime manufacturer warranty with this product. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) If your purchase has passed the store's return policy period, please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
•
•
and any other accessories that came with the original package
must be included.
Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
7
About SIIG, Inc.
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer
of I/O connectivity products, including PCI & ISA serial and parallel
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),
networking, sound cards, and other accessories. SIIG is the premier
one-stop source of upgrades.
SIIG products offer comprehensive user manuals, many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK, and through e-commerce sites.
PRODUCT NAME
SATA-to-IDE Adapter
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
SATA-to-IDE Adapter is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of
SIIG, Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries. Pentium is a registered trademark
of Intel Corporation. Other names used in this publication are for identification only and may be
trademarks of their respective companies.
April, 2008
Copyright © 2008 by SIIG, Inc. All rights reserved.