Download Pioneer PD-M450 User's Manual

MULTI-PLAY COMPACT DISC PLAYER
PD-M550
PD-M455
PD-M453
PD-M450
DIGITAL AUDIO
PD-M455
PD-M450
Thank you for buying this Pioneer product,
Please read through these operating instructions so you
will know how to operate your model properly. After you
have finished reading the instructions, put them away in a
safe place for future reference.
in some countries or regions, the shape of the power plug
and power outlet may sometimes differ from that shown in
the explanatory
drawings.
However, the method of
connecting and operating the unit is the same.
WARNING:
To PREVENT FiRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT
NOTICE
[For U.S. and Canadian models]
The serial number for this equipmentis located on the rear panel.
Please write "_hlsserial number on your enclosedwarranty card
andkeep it in a securearea. This is for your security.
"This
product
complies
with
the
Radio
interference
ments
of the EC (European Community)Directive 87/308/EEC."
LINE VOLTAGE
SELECTOR
SWITCH
Only multi-voltage models are providKI with this switch.
U.S., Canadian, European, U.K., and Australian models
are not provided with this switch.
Mains voltages in Saudi Arabia are 127V and 220V only.
Never use this model with 110V setting in Saudi Arbia.
The line voltage selector switch is located on the rear panel
of this player. Before your player is shipped from the factory,
the switch is set to the power requirements of the player's
destination. Check that it is set properly before plugging
the power cord into the outlet. If the voltage is not properly
set or if you move to an area where the voltage requirements
differ, adjust the selector switch as follows:
• Use a medium-sized (flat blade) screwdriver. Insert the
tip of the screwdriver into the groove of the selector
switch and turn it so that the power voltage making of
your area points to the arrow.
requireVOLTAGE SE LECTOR
THE POWER SWITCH IS SECONDARY CONNECTED AND ]
THEREFOREDOES NOT SEPARATETHE UNIT FROM MAINS
POWERIN STANDBY POSITION.
PIONEER"
The Art of Entertainment
IMPORTANT
1
CAUTION
The
lightning
triangle,
flash
with
is intended
uninsulated
enclosur
arrowhead,
to
ater_ ttle
"dangerous
withfn
user
voltage"
e tha_ may be of _u f ticient
a risk of electric
shock
an equilateral
to the
within
CAUTION:
presence
the
magnitude
The
of
TO
product's
PREVENT
NOT
THE
REMOVE
SERVICEABLE
IMPORTANT
apparatus
see
REAR
connection
is fitted
with
FACILITIES
of additional
Hi-Fi
that
the
power
switch
power
for
ELECTRIC
(DR
SHOCK,
BACK).
NO
DO
PARTS
INSIDE,
SERVICE
REFER
SERVICING
Make
wires
in
accordance
all
and the signal terminals
wall
socket
last Imake
As the
is oft.I
mains
lead
Due:
the following
Neutral
Browm
Live
colours
apparatus
of the
may
not
marking
identifying
as f otIOWS:
the
within
User
an equilateral
TD
triangle
to the presence
is
of important
Iservicing)
instructions
the appliance
in
PERSONNEL.
this
with
point
to alert
operating
and mairltenan_te
the riterature
accompanying
The wire which
is co,cured
blue
the
terminal
which
[s marked
coloured
black
The
outlet(s),
The
exclamation
intended
USER-
FOR USE IN THE UNITED
KINGDOM
convenient
component(s).
connections
to the AC ougetls)
first.
Connect
_he _lug to the
sure
2
AC mains
PANEL
OF
to constitute
to persons
QUALIFIED
If the
RISK
CDVER
are
coloured
to
in
wire
the
co_oured
code:
DO not
three
wires
in tile
mains
correspond
the
lead
with
terminals
which
the
in your
plog
crown
he connected
the letter
N
must
be connected
which
is marked
with
the
either
wire
earth
letter
to
or
L or
red,
connect
pin
to the
terminal
of a
plucJ
Equipment
plug.
of this
coloured
is coloured
terminal
mus!
with
sold in the
U,K.
is not supplied
with
a power
proceed
SAFETY INSTRUCTIONS
READ
INSTRUCTIONS
instructions
Qperated,
RETAIN
-
should
Ag
-- The
be reIained
HEED WARNING
the
safety
and
before
operating
operating
for future
- All warnings
operating
on the appgance
instructions
should
be
adhered
to
should
MOISTURE
near water
washbowl,
LOCATION
stable
WALL
for
kitchen
laundry
- The
location.
appliance
OR
CEILING
not
The
proper
should
-
appliance
ventgatlon.
The
For
the
that may block the ventilation
in a built in installation,
such
-- The
heat
appliance
sources
stoves,
that
POWER
or
produce
SOURCES
nected
to
should
such
other
as
The
a power
be
walked
routed
on
against
or
them
convenience
they
exit
POLARIZATION
vided
-
with
following
-
so that
Pay
plugs,
where
If your
instructions
This
will
fit into the
safety
feature
not
be
congo-
he se rviced
by a Pioneer
center
or quafified
are unable
only
Objects
have
(he
appliance
The
appliance
your
safety
purpose
CLEANING
with
dean
other
-
outlet,
of the
polarized
appliance
should
volatile
2
<PRB1142>
liquids
since
they
the
plug
fallen,
has
or fiquid
been
has
appliance
service
when:
exposed
US.A,
Code,
ANSI/NFPA
and
supporting
dam-
wire
to an antenna
spiged
Lnto
CART
70-1984,
structure,
of
[heappliancedoesnotappeattooperatenormally
built
Electrical
provides
grounding
unit,
and
National
grounding
discharge
tO grounding
surges
informaof the
mast
of the lead-in
size of grounding
antenna
discharge
electrodes,
and
unk,
require-
ments
for the grounding
electrode
See Fig A,
- An appfiance
and cart combination
should
he
moved
with care Quick stops, excessive
force,
uneven
surfaces
may cause
the appfiance
and
combination
to overturn.
to rain
or exhibits
a marked
change
in performance.
The appliance
has been
d_oppe_
or the enclosure
-
The
the appliance
ting instructions
nearest
Pioneer
user
should
beyond
that
not
attempt
described
and
cart
to service
in [he
opera-
For all other servicing,
conta¢I
authorized
service
center.
Ihe
NEC
.
or
to cords
at
the
point
product
is
please
read
is
This
to insert
the
_"
GROUND_
pro _
may
ANTENNA
DISCHARGE
the
INEC
SECTION
UNIT
810
GROUNDING
is a
20)
defeat
cleaned
corrode
CONDUCTORS
810
plug
S
the
POWER SERVICE GROUNDING
plug
be
IN
WIRE
equipped
one way.
not
ANTENNA
LEAD
CLAMP
Do
810 of the
No
an
so as to provide
voltage
to proper
location
conneetlon
if an outside
ter rT=inal, be sure
is grounded
against
section
respect
conductors,
has been
been
system
In the
tion with
a uthorized
personnel
or
[o be
ELECTRODE SYSTEM
only
a polishing
cloth
or a soft dry cloth.
Never
with furniture
wax, benzine,
insecticides
or
cabinet
En
The
obs(;lete
cord
antenna
some protection
up static charges.
not spilled
•
fully into the outlet,
try reversing
the plug
If the
plug shoulP still fall to fit, contact
your electrician
to
replace
service
power-supply
the
un-
be taken
are
should
current line plug (a plug
than the other)
This plug
outlet
fall and liquids
cords
upon
and
product
if you
should
left
-
antenna
damaged
type
likely
placed
plug,
power
do not
when
to the
from
supply
are
purchased
with a polarized
alternating
having
one blade
wider
the
attention
power
outlet
through
openings
SERVICE
The
appliance
a polarized
the
GROUNDING
is connected
or as marked
receptacles,
the
from
enclosure
REQUIRING
The
OUTDDDRANTENNA
appliance
registers,
should
of
items
particular
be located
of the
amplifiers)
Power
they
by
from
away
heat
only
obiects
the
SERVICING
of air through
instructions
pinched
appliance
situated
appliance
PROTECTION
should
flow
cord
•
SO
with
ru g, or simiiar
[including
supply
scribed in the operating
en the appliance
POWER-CORD
be
•
openmgs;
or.
as a bookcase
radiators,
abptiances
heat.
-
sofa,
the
•
appfiance
interfere
example,
not be situated
surface
placed
may impede
openings.
•
in a
be situated
not
should
or cabinet
that
the ventilation
base-
ceiling
should
does
on a bed,
a bathtub,
installed
or
should
tenna
power
aged.
be
to a waft
or position
into
DAMAGE
not
in a wet
antenna
lines,
- The
be unplugged
so that
in
etc.
MOUNTING
that its location
near
tub,
pool,
be mounted
-
appliance
example,
sink,
a swirnmlng
VENTILATION
HEAT
The
or near
should
its
--
power
used for a long period
of time
OBJECT
AND
LIQUID
ENTRY
- Care
in
use
- An ou [door
from
PERIODS
should
and
WATER
ment,
LINES
away
instructions
and
be used
is
reference.
FOLLOW
INSTRUCTIONS
- All operating
structions
should
be followed,
AND
POWER
the appliance
NONUSE
INSTRUCTIONS
should
the
be read
the
FIG. A
(NEC ART 250, PART HI
- 211
NATIONAL
ELECTRIC
CODE
[FOR EUROPEAN
i
i
AND U.K. MODELS]
The following caution label appear on your player.
'l
i
,
CAUTION
Location: r_ar of the player
This product contains a laser diode of higher class than
1. To ensure continued safety, do not remove any covers
or attempt to gain access to the inside of the product.
Refer all servicing to qualified personnel.
[FOR U.S.
CAUTION
•
MODEL]
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous
exposure,
The use of optical instruments with this product will increase eye hazard.
•
radiation
i
i
INFORMATION
TO USER
[FOR
This
equipment
generates
and
uses radio
frequency
energy
and _f not installed
and used propeay,
that is, in
strict accordance
with
the manLJfacturer's
instruot;ons,
may
Cause
interference
ti_n.
It has
heel1
the limits
fo_ a Class
with
specifications
the
Rules.
which
tection
against
lation.
However,
will
not
occur
are
to
Wpe
{_sted
radio
_tld
and
a computing
such
there
to
J
provide
interference
of Part
15
reasonable
that
installation
with
'accordance
in a _esidentia_
is no guarantee
in a particular
r_'c_-
to comply
clerics'in
in Subpart
designed
t_ewsion
found
of FCC
U.S.
MODEL]
If this
ing
the
equipment
equipment
does
cause
off and
_n,
television
try
to c_vrect
feceptiOnr
t_
inteHerence
which
can
fOllOwing
• reorient
measu:es:
the receiving
interference
the
user
radio
!_o
is encourllged
o
by
be one
determined
m mo_e by of turfit
antenna
/
pro-
•
•
relocate
this equipment
with respect
move Ibis equipment
away
from
the
instal-
•
plug this
equ=pmen
interference
to
I
I
to the recelv_r
receiver
equipment
into a different
outlet
so
and receiver
are on ddferet_
branch
lh_at
cir-
It necessary,
the
experlenced
radio/television
should
consult
the
technician
dealer
for
or
an
additional
suggestions.
The user may find the following
booklet
prepared
by the Federa_ Communications
Commission
helpful:
"'How
to
Problems"
This
Identify
booklet
is
Printing
Office,
004o000_003t_5-_,
and
Resolve
avagable
Radio-TV
from
Washington.
the
0 C,
interference
US
Government
204OZ.
Stock
No
to units
which
will
,
cuits
The above
be
[For Canadian
user
Operated
it_struclions
in the
apply
Umted
only
States
model]
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communication s.
POWER-CORD
i.
CAUTION
Handle the power cord by the plug, Do not pull out the plug by tugging
the cord and never touch the power cord when your hands are wet as
this could cause e short circuit or electric shock. Do not place the unit,
a piece of furniiure,
etc., on the power cord, or pinch the cord. Never
make a knot in the cord or t_e it with other cords. The power cords
should
damaged
be routed such that
they are not
likely
Dower cord can cause fire or give you
to be stepped
on. A
an electrical shock.
Check the power cord once in a while. When you find it damaged,
ask
your nearest PIONEER authorized service center or your dealer for a
replacement,
3
<PRB1142>
En
i
PUTBATTERIES
INTOTHEREMOTECONTROL
I CONTENTS
UNIT(Pl -M550/PDM455iPD-M453only)
CONFIRM SUPPLIED ACCESSORIES ............................... 4
PUT BATTERIES INTO THE REMOTE CONTROL UNIT .... 4
CAUTIONS REGARDING HANDLING ................................ 5
CONNECTIONS .................................................................
6
BEFORE OPERATING THE PLAYER .................................. 6
NAMES AND FUNCTIONS OF PARTS ............................... 8
BASIC OPERATION ..........................................................
10
To play a compact disc ...................................................
10
To stop playback and take out the magazine ................. 10
Time display ...................................................................
11
VARIOUS OPERATIONS ..................................................
11
Disc search - To search for a particular disc .................. 11
Track search - To search for a particular track ............... 11
Manual search - To search for a particular passage ....... 12
To repeat playback (repeat play) .................................... 12
Random playback - To play all tracks in random order ... 12
Magazine Hi-Lite Scan ...................................................
12
Adjusting the sound volume (PD-M550/PD-M455/
PD-M453 only) ...............................................................
13
ADLC (Automatic Digital Level Controller) ..................... 13
TO PLAY ONLY DESIRED TRACKS/DISCS ...................... 14
Program playback - To program tracks/discs
in desired order ..............................................................
14
Programming a pause ....................................................
15
To clear all of the program contents .............................. 15
To erase a program (PD-M550/PD-M455
/PD-M453 only) ..............................................................
15
To check the program contents (PD-M550/PD-M455
/PD-M453 only) ..............................................................
15
To modify the program contents (PD-M550/PD-M455
/PD-M453 only) ..............................................................
15
Delete program playback - To delete undesired
tracks/discs ....................................................................
16
To clear all of the delete program contents ................... 16
CONVENIENT OPERATION FOR RECORDING ............... 17
Compu program editing (Computer allocated program
editing) ...........................................................................
17
Time fade editing ...........................................................
18
TROUBLESHOOTING .......................................................
19
SPECIFICATIONS ................................................
Back cover
I
PD-M550
i
I
PD-M455/_D-M453
% %
Open the lid oi the battery compartmenton the rear of the remote
control unit, aind insert the batteries, taking care to align the (+)
and ( - ) polarities correctly.
NOTE:
•
•
In order to iprevent battery leakage, remove the batteries when
not using t_e remote control unit for an extended period (one
month or r_ore). In the event of battery leakage, carefully wipe
away any _attery fluid inside the compartment, and replace the
batteries _'th new ones.
Do not allow books or other objects to rest on top of the remote control unit, since the buttons may be depressed, causing
faster exhaustion of the batteries.
Incorrect use of batteries may cause leakage or rupture.
Always be f_ure to follow these guidelines:
A. Always iinsert batteries into the battery compartment
correetl'_ matching the positive (_) and negative C)
polarities,
as shown
by the display
inside
the
compa_ment.
B. Never mix new and used batteries.
C. Batteries of the same size may have different voltages,
dependipg
on brand.
Do not mix different
brands of
batterie S.
CONFIRM SUPPLIEDACCESSORIES
Q
0
®
PD-M550
PD-M455/
PD-M453
_)
(_) Control cord x 1
PD-M550/pD-M455/PD-M453
(U.S. and Canadian models only: Not available with models for
military zo#es (multi-voltage types))
PD-M450 {all models)
(_) Remote cCntrol unit x 1 (PD-M550/PD-M455/PD-M453
only)
@
®
4
<PRB1142>
En
6-Compec_ Disc Magazine x 1
(Called 6-disc magazine in the explanatory text.)
NOTE:
'
The supplied 6-disc magazine is for 12 cm discs only.
Output cord x 1
®
(_) AAA/R03
only)
dry cell batteries
x 2 (PD-M550/PD-M455/PD-M453
J
I CAUTIONSREGARDINGHANDLING
I Location
Install
the
Cleanin_ ! discs
player
in a well
ventilated
location
where
it
•
will not be exposed to high temperature
or humidity.
Do not install the player in a location which is exposed to direct
rays of the sun, or near stoves or radiators. Excessive heat can
J
The pres_'nce of fingerprints or smudges on the surface of the
disc will r at directly affect the recorded signals, but depending
on the d _gree of contamination, the brightness of the light
reflected from the signal surfaces may be reduced, causing
degradat/_ ,n of sound quality. Always keep your discs clean by
wiping th ,m gently with a soft cloth from the inner edge toward
the outer )eriphery.
adversely affect the cabinet end internal components.
Also.
installation of the player in a damp or dusty environment
may
result in malfunction or accident• (Alsoavoid installation near cookers
etc.. where the player may be exposed to smoke from oil, steam
or heat.)
•
if a disc bffcomes very dirty, dip a soft cloth in water, end after
wringing itlout well, wipe the dirt away gently, and then remove
any water _lrops with another soft, dry cloth,
m Do not use_record cleaning sprays or anti-statlc agents on discs•
Also, neve I clean discs with benzene, thinner, or other volatile
solvents, slnce damage to the disc surface may result.
.,,Precautions regarding installation
s
Placing and using the compact disc player for long periods on
heat-generating
sources
such as amplifiers
will affect
performance.
Avoid placing the player on heat-generating
sources.
•
•
•
Install this compact disc player as far as possible from tuners
and TV sets. A compact disc player installed in close proximity
to such equipment, may cause noise or degradation of the
picture.
Such noise may be particularly noticeable when an indoor •
antenna is used. In such a case, make use of an outdoor antenna,
or turn off power to the compact disc player.
Please place this unit on a level surface•
l Condensation
!
(Storing without
•
J
•
When this unit is brought into a warm room from previously cold
surroundings
or when the room temperature
rises sharply,
condensation may form inside, and the unit may not be able to
attain its full performance. In cases like this, allow the unit to stand
for about an hour or raise the room temperature gradually.
/_
";'1
7.
'
using the 6-disc magazine)
Discaarem_deofthesamekindsofplasticusedforconventionai
analog audilo records. 8e careful not to allow discs to warp;
always starve discs in their cases vertically, avoiding locations
with high Neat or humidly,
or extremely low temperatures•
Avoid leavir_g discs in cars, since the seat of a car in direct
sunlight can'I become unbelievably hot,
Always roe d and abide by the precautionary notes listed on disc
labels.
L/-,,-"
( CO lens
cleaner
l
The player's pi?kup [ens should not become dirty in normal use,
but is for some reason it should malfunction due to soiling, ask
your nearest PIONEER authorized service center, Lens cleaners
for CD players are commercially available, but special care should
be exercised in their use since some may cause damage to the
lens,
i
( Cleaning tl_e player and the magazine
!
/
To clean the PLAYER and the MAGAZINE wipe with a soft, dry
cloth. For stubl_om dirt, wet a soft cloth with a mild detergent
solution, wnng well, then wipe off the dirt. Also use a dry cloth to
wipe "_hesurfac_ dry, Do not use volatile liquids such as benzene
and thinner which are harmful to the unit.
I
5
<PRB! 142>
En
CONNECTIONS
• Make sure that all of the components
F
Red_
are turned off before making connections.
Output c///ord
White
f
CD ,ayo
Poworoo,d
/
Cassette deck
/
CD-DECK SYNCHRO cord
Making connections
[]
Connect the OUTPUT jacks of this unit to the input jacks (CD or
AUX) of the amplifier,
Make sure that the white plugs are
connected to the left (L) jacks and the red plugs to the right (R)
jacks.
•
Be sure not to connect this unit to the amplifier's PHONO
jacks, as sound will be distorted and normal playback will not
be possible.
Connect the power cord to a household AC wall outlet or an AC
outlet on your amplifier.
Make sure plugs are inserted fully into the jacks and wall outlet.
[]
•
CD-Dack synchro function
If you have a Pioneer cassette deck provided with the CD-Deck
synchro function, connect the CD-DECK SYNCHRO jacks of the
CD player and cassette deck, With this function, synchro recording
can be carded out between player and deck.
• For details on connections and operation, refer to the instruction
manual supplied with the cassette deck.
• The CD-DECK SYNCHRO cord is not supplied with the CD player.
r Dmote control with
amplifier 1hat has the [] mark
System
a Pioneer
stereo
(Available wit the PD-M450 and U.S. and Canadian models of the
PD-M550/PD M455/PD-M453
only: Not available with models for
military zone,' (multi-voltage types))
When • Pior ear stereo amplifier bearing the [] mark is used,
connect the ;ONTROL IN jack on the rear panel of the CD player
to the CONT _OL OUT jack of the amplifier. This witl enable the
CD player to be controlled using the remote control unit supplied
with the ster, Jo amplifier, If you do not plan to use this feature, it
is not necess Jry to connect CONTROL IN/OUT jacks.
• The contr( ,I cord is supplied with the CD player.
• The ramp1 • control unit supplied with the amplifier can be used
to control Slay, Stop, Pause, Track!Disc Search and Disc Change
operation.'
• For instru ;tions regarding connections and operation, refer to
the opera ling instruction manual provided with your stereo
amplifier.
NOTES:
• When a o _ntrol cord is connected to the player's CONTROL IN
jack, dire€ ! control of the player with the remote control unit is
not possfl ,le. Operate the player with the remote control unit
by aiming ¢tat the amplifier.
• Be sure t( connect both of the control cord's plugs securely to
the CONT _OL tN and CONTROL OUT terminals. Do not connect
nd of the cable.
only
one
• Be sure t_ turn off the power of the ampfifier when connecting
the poweJ cord and output cord,
BEFOREOPERATINGTHE PLAYER
CARE OF DISCS
•
•
With this player, use
(Optical audio digital
When holding discs,
the edges, or by one
DIGITAL
6
<PRB1142>
En
AUDIO
discs which display the mark shown below.
discs.)
do not touch their signal surfaces. Hold by
edge and the center hole,
•
Do not affix gummed labels or tape to the label surfaces. Also,
do not scratch or damage the label
•
Discs rotate at high speed inside the
damaged [cracked or warped) discs.
player.
Do not use
BEFOREOPERATINGTHEPLAYER
NOTE:
• In order I play an 8-cm CD you will need a special Multi-Play
Magazine (JD-MI08, JD-M308) which is sold separately. Be
sure to re ad thoroughly the Operating Instructions before using
1
•
•
•
8,cm CD, daptors
It is pose, tie that even an adaptor which meets recommended
standard
D specifications wil! not be usable with tt_ CD player.
It is recor _mended that the special Multi-Play Magazine 1JDM108, JD _4308) be used.
Never Ioaqt an 8-cm CD or its adaptor into a standard 12-cm
magazine. This may seriously damage the CD player,
Do not in.,err only an 8-cm disc and adaptor into the supplied
magazine,,
INSERT DI $CS INTO THE 6-DISC MAGAZINE
2
Insert any dis_s which you may have into the supplied magazine.
Up to six disc_ may be inserted, The numbering of the discs begins
with 1 at the topmost tray, and then increases in order from 2 to 6
for the lower tl'aya. The magazine has a window through which the
pulled-out dis_ tray can be checked. Even during playback, the
number of the disc being played back can be checked through this
window.
1
2
3
4
Pull ou_only one disctray.
Positioq discs with the label side downward.
Put theldisc tray back as it was originally.
Insert other discs by repeating steps I to 3.
CAUTION:
• Please mak
•
•
•
sure to only pull out one disc tray at a time. (when
a disc tray I as been pulled out, do not pull out other disc trays.)
Ifdiscs are inserted label side upward, it will not be possible for
them to be )layed. Please make sure to insert them with the
label side d )wnward.
Objects ot er than discs (song cards, explanations of disc
contents, et ;.), must never be inserted into the disc trays.
Do not touc the playing surface of discs (iridescent side) with
hands or fin era.
AFFIXING
B
"CB
A
•
B
f--A-H
•
•
For U.S. customers only
You may purchase additional Pioneer six-compact-disc magazines
from your dealer. If however, they are not avairable at your
dealer in the United S_ates, you may order from:
PIONEER ELECTRONICS SERVICE, INC.
2265 East 220th Street
P.O. Box 1760, Long Beach
CA. 90801-1760
ABELS TO THE MAGAZINE
AJways art ch the labeJs provided in the designated locations,
Correct op, _ration may not be possible if labels or tape are
attached in 3that locations,
The followiJ Dgare convenient ways of using labels:
A: For title 3
B: For dis( names
C: For ¢laEsification
Do not atta, ;h labels on top of other labels,
Additional
available as
M108, JD-IV
Please use t
lagazines identical to the one supplied are
options (*JD-M100, JD-M200, JD-M300, JD308).
1am to make your own disc library, with separate
magazines f >reach artist or genre.
* JD-M100/JD. M2OO/JD-M300 ......... Magazine for 12-cm discs
JD-M 108/JD, M308 ........................... Magazine for 8-cm discs
NOTE:
Do not load B-c_n discs into the magazine for 12-cm discs.
I
Phone #(800)421-1404
7
<PR81142>
En
NAMES AND FUNCTIONSOF PARTS
l
PD-M550
PD-M455
I!
PD-M453/PD-M450
FRONT PANEL
O POWER STANDBY/ON
switch and STANDBY
indicator
@ REPEl ,'I" button
(_ RAND C)M PLAY button
(_ AUTO FADER button
@ HI-LIT -."SCAN button
TIME button
O Remote sensor (PD-M550/PD-M455/PD-M453
_ Stop ! ,utton (ll)
@ Pause button (11)
only)
_
Receives the signal from the remote control unit.
• The PD-M450 is not equipped with the remote sensor.
@
Disc number buttons (DISC 1 - DISC 6)
_) PGM (program) button
(_ TRACK NUMBER/Digit
(PD-M550 only)
TIME FADE EDIT button
buttons (1-10, +10,_20)
Manu; |1search buttons (<1</1_)
Play b ,_tton (1_-)
_) Track ;earch buttons (I<I_I/I_IH)
_ ADLC Automatic Digital Level Controller) button
_ DELE7 'E button
_) EJECT button (_A)
(_ HeadF hones jack (PHONES) (PD-M550/PD-M455
only)
COMF U PGM EDIT button
(_ Magazine insertion slot
_) Head ,hones
volume
M550 PD-M455 only)
8
<PRB1142>
En
(PHONES
LEVEL) (PD-
PD-M550
PD-M455/PD-M453
DI
Ill
@
O
=:_
_j-
@
@
@
®
@
®
(#
@
®
@
REMOTE CONTROL UNIT (PD-M550/PD-M455/PDM453 only)
Remote control buttons with the same names or marks as buttons
on the front panel of the player control the same operations as the
corresponding front panel buttons.
(_ POWER button
ADLC (Automatic Digital Level Controller)
button
MANUAL search buttons ( _
/ IH_ )
(_ TRACK search buttons [ _
/ _
)
PAUSE button ( li )
(_ STOP button ( II )
(_ Track number/Digit buttons (1-10, +10, _ 20)
(PD-M550 only)
PGM (program) button
(_ CHECK button
DISC NUMBER buttons ( 1 - 6 )
OUTPUT LEVEL buttons ( +/- )
RANDOM PLAY button
(_ HI-LITE SCAN button
(_ PLAY button ( I_ )
(_ DELETE button
REMOTE C DNTROL OPERATIONS
M455/PD.It 1453 only)
(PD-M550/PD-
the remote control unit, point the unit's infrared
When operatin
signal transmitl r at the remote control receiver (REMOTE SENSOR)
on the front par el of the player. The remote control unit can be used
within a range o =about 7 meters (23 feet) from the remote sensor, and
within angles c Fup to about 30 degrees.
NOTE:
If the remote c_,ntrol sensor window is in a position where it receives
strong light su{ h as sunlight or fluorescent light, control may not be
possible.
Notes for PD-JVI460:
Operate the =D-M450 using the remote control unit which
accompanies
e amplifier. (See page 6.)
(_ CLEAR button
FADER button (PD-M455/PD-M453
only)
9
<PR81142>
En
BASICOPERATION
!
To play _ compact disc
PD-M550
1 Turn on the power to the player.
2 Insert
magazine, pushing it in until a click
sound
heard.
•
1
2
PD-M455/
(PD.M4531
PD-M450)
3
•
3
Dil
!
-
ml
i
Insert _ediscs to be played into the magazine beforehand.
(Refer 1o "BEFORE OPERATING THE PLAYER" on page 6.)
When the power is turned off, inserting
a magazine
autom_
tically turns on the power (Automatic Power On
functio_ i).
Press
I_ to start
playback.
I
IIIll ,.I.t
*: PD-M455/PD-M453 only
**: PD-M455 only
**
1
To pause pla tback temporarily:
Pressll. The I indicator lights and playback is paused at that point.
Pressing II a_ ain or I_ resumes playback from the position where
pause mode_ vas entered.
To stop playl _ack:
Press •. Th_ player returns to the beginning of the first track on
the disc at w_ ich playback was stopped. If • is pressed twice, the
player retum_ to the beginning of the first track on the first disc
and enters st( ,p mode.
POWER
STANDBY/ON
2
NOTE:
When the po_ ver is turned off while a magazine is in the player, the
player memol rzes which disc was played just before the power was
turnedoff. Th is, when the power is next turned on, pressing the play
button starts _layback from the first track on the memorized disc.
To stop
3
@@@@@@
and
take
out
the
magazine
j
NOTE:
Dome mode llows you to see variation of the display. To enter the
within 1 second without
dome mode, _ress POWER and then _
inserting the i _agazine. To exit demo mode, insert the magazine or
press any but "on.
PLAY
D
layback
Press EJECT, remove the magazine, and then press POWER to
turn off the pc wer,
Even when t_ e power is turned off, the magazine will be ejected
by pressing E, IECT. (Power Down Eject)
'
Cautions r agarding handling of magazines
U PAUSE:
•
PAUSE
n
•
•
•
•
• STOP:
--
When insc rting a magazine into the player, make sure that the
direction o insertion is correct.
After use, store in the case provided. Do not place in locations
subjected :o high temperatures or exposed to direct sunlight.
Do not tak magazines apart.
Be careful not to drop, or hit magazines against things. Also do
not apply., trong force to trays which have been withdrawn.
of benzene, thinner, insecticide or other volatile
Applicatior
liquids to a magazine may damage the surface, so keep
magazines 'away from such substances,
STOP
a
Operations indicated by the [ _ ] mark are performed with the
remote control unit. (PD-M550/PD-M455/PD-M453
only)
I[_t11111"a_
k,
l0
<PRB1142>
En
BASIC OPERATION
Timer playback
By using a commercially available audio timer, it is possible to
initiate playback at any time automatically,
1. Insert a magazine into the magazine slot.
2. Set the time at which you wish playback to begin. The timer
will supp{y power to both the amplifier and the p{ayer at the
preset time, turning all the components on and initiating the
playback mode, Playback starts from the first track on the first
disc.
} Time displ, y
During playback, )ressing the TIME button changes the time display
in the following ,' equence: (_) Time (elapsed playback time of the
track being playe J) "_ (_) Remain (remair_ing p_ayback time of the
track being playe, I) --* @ AL Remain (remaining playback time from
the playing point lo the end of the disc) --* @ Total (total playback
time of the disc).
• With track N, ,. 24 or more, the Remain time ® cannot be
displayed.
• During progra m playback, delete program playback, random
ptayback or de lete random playback, AL Rema(n time _) cannot
be displayed.
• During Progral n playback, the number of program steps can be
displayed witt" the Total setting @.
Caution:
• Do not unplug the power cord or do not turn off the power with an
audio timer during playback, as this could result in damage to the
disc.
•
!
If a power failure occurs while the power is turned off (standby
mode), the power is automatically turned on with timer playback
function when the power is supplied. THEREFORE, DISCONNECT
THE AC POWER CORD WHEN THE PLAYER IS NOT USED FOR
A LONG PERIOD OF TIME.
®
®
I
(_
t
T_ME
_
O
--
I
I--
(PD-
--
_
(PD-M455i
PD-M450)
(_
U q
so
J VARIOUSOPERATIONS
To search for tra¢l No. from 1 to 10, simply press the corresponding
buttons (_- 1L!_0J).To search for track N._or
above, use
__OJ. To search f :)r track No. 20 or above u_.
LTJ
Example
To enter track No. 17: [_,
To,
[_][[_:_
rater track
track No.
No. 23:
30: _
To 4rater
as 0,
• When entering 20 or above, [_]functions
• When _
O• _
is pressed, the digit button to be next
entered should be pressed within 5 secor_ds.
I Disc search - To search for a particular disc
During playback or stop mode
PD-M550
1
toJsc1Io=sc__DISC
3 [ alSO
_t OISC
_tD_SC
S
2
3
DISC NUMBER
4
5
PD-M455/PD*M453
DISC NUMBEFt
6
]
NOTE:
t
During program [ layback, the track search can not be operated
with the TRACK A UMBER button.
During playba_ k or pause mode
TRACK SEARCH
PD-M550
When DISC NUMBER (DISC 1 - DISC 61 is pressed, the player
searches for the specified disc and playback start& from the
beginning of that disc.
NOTES:
/
•
If "dISC" appears on the display, you have pressed the disc
number of a tray which does not contain a disc.
w During program playback, Disc Search cannot be carried out.
I Track search - To search for a particular track
}
During playback or stop mode (PD-M550 only)
{
1
I
2
I
3
I +10
I]
[I 7 I a I s I lolJ
/2
I '_
]
ES ESI
'11
PD-M455
(PD-M45&/
PD-M450)
_
_<
I
_
I1
._
When _
is pre,' _ed once, playback advances to the beginning of
the next track. VVI_enthis button is kept pressed, playback advances
to successive trac s on the disc.
When _
is pros sod once, playback returns to the beginning of
the track being pie fed. When this button is kept pressed, p{ayback
returns to earlier tl acks on the disc.
• For PD-M550/F 3-M455/PD-M453, the _
or _
button on the
remote control unit can be used.
NOTES:
• During normal, #ayback, Track Search can be carried out on one
disc only.
orl_,l button can be used to
= During progran , playback, the _
select the pro_ "ammed track.
[t_agttt_ L
11
<PRB1142>
En
VARIOUS
OPERATIONS
Manual search - To search for a particular
passage
1
........
Rando _t playback
J rander _ order
- To play all tracks in
During playback or pause mode
RANDOM
PD-M550
PD-M455
MANUAL
I "_
I
PLAY
(PD-M453/PD-M450)
SEARCH
v_
/9
='_""""'l
W
Press RAN_OM PLAY, The RANDOM indicator lights and all tracks
on all discs[are played in a random order.
To play tra#ks other than the deleted tracks in a random order.
press RAk_DOM PLAY after carrying out the Delete Program
procedure. See "Delete Program Playback" on page 16.
i
MANUAL
/?
i
i
While _
is kept pressed, playback rapidly advances toward the
end of the disc. When playback reaches the end of the disc, the
player enters pause mode and "End" is displayed. While _
is kept
pressed, playback rapidly reverses toward the beginning of the
disc.
I Mag azi_le Hi'L"e scan
J
I
When the desired passage is reached, release _
of" _1.
The
player enters original mode (playback or pause) where _
or _1
is released.
]
During stop mode
SCAN
W
HI-LITE
NOTES:
• During normal playback, Manual Search can be carried out on
one disc only.
• During program playback, Manual Search can be carried out in
one program step only.
I
i
/
When HI-LIrE SCAN is pressed once during stop mode, playback
starts from _point I minute after the beginning of the first track, and
the first trec_ of each disc is played for about 10 seconds. The DISC
SCAN indic,_tor blinks during Disc Scan mode. After the first tracks
of all discs are scanned, the player enters stop mode.
To repeat playback (repeat play):
To repeatedly
REPEAT []
J
play the displayed track, press REPEAT once. The
indicator lights. The REPEAT button can be pressed in
any playback mode.
To repeatedly play all tracks on all of the discs in normal playback
mode or in the specified playback mode (Program playback, Delete
program playback or Random playback), press REPEAT twice. The
REPEAT indicator lights.
• To exit repeat mode, press REPEAT so that the REPEAT [] or
REPEAT indicator goes off.
12
<PRB1142>
En
When HI-LI" - SCAN is pressed twice during stop mode, playback
starts from a _olnt 1 minute after the beginning of the track, and each
track is playe Ifor about 10 seconds. The SCAN indicator blinks during
Track Scan r _ode. After all tracks of all discs are scanned, the player
enters stop node.
To exit Ma_ azine Hi-Ute Scan mode
Press e, i_, I )isc number(DISC1 - DISC6) or TRACK NUMBER (1-10,
+10, >20)
When I_ is pressed, normal playback starts from the
current poin • When DISC1-DISC 6 or TRACK NUMBER (PD-M550
only) is pre ;sed, the selected disc or track is played from the
beginning,
NOTES:
,
• Hi-Lira S, :ancan be carried out from the desired elapsed time of
the track During playback, press HI-LITE SCAN at the point you
want to ;tart Hi-Lite Scan playback. The player memorizes the
minute a _dsecond of the point and Track Scan playback is carried
out from the memorized minute and second on each track.
• Each tim HI-LITE SCAN ispressed, the mode switches be tween
Disc Sca and Track Scan.
• Program. ning of only desired tracks is possible during Track Scan
playback See "Direct program" on page 14.
• During Tr, ick Scan playback, you can skip to the desired track with
or _ _L
• WhenRE =EAT is pressed, Hi-Lite Scan playback will be tepee ted.
• Whenpla fback time of a track is less than one minute or is shorter
than men orized time, Hi,L/te Scan playback is carried out from the
beginnin_ of the track for about 10 seconds.
When pl_ _'back time of a track is less than 10 seconds, the track
is played rrorn the beginning to the end.
VARIOUS
OPERATIONS
AC power ¢o_d connection and functions
Some function,s cannot be carried out depending on the connection
I M455/PD-M453
Adjusting the sound
only) volume (PD-M550/PD-
of AC powe r c_rd.
I
L
Function
I
/2
_
O_PUT
WhentheACpower
cord is connected to
the
unswitched
outlet of anamplifier
or wall outlet.
When the AC power
cord is connected to
the switched outlet of
an amplifier or audio
timer,
Timer playbacl
No
Yes
Program mere _ry
Yes
No
Yes
No
Yes
No
LEVEL
i
Press OUTPUT LEVEL "-" or "+" to adjust the output level. The
output level can be adjusted between 0 dB end -25 dB in steps of
1 dB.
• The output level at the OUTPUT jacks and PHONES jack will be
adjusted simultaneously.
l
Delete
memory
program
Outputlevelm
Jmory
For details, refe I to the description of each function of this Operating
Instructions.
ADLC (Automatic Digital Level Controller)
1
When the difference of recording level between discs is noticeable,
the volume level should be adjusted for each disc, especially during
program playback or random playback whose tracks are selected
between 2 discs or more. In such cases, pressing ADLC automatically
sets the output level to the proper level. When ADLC is turned on,
the ADLC indicator lights.
• ToturnoffADLC,
pressAOLCsothattheADLCindicatorgoesoff.
• With some selections, sound becomes unnatural. In such cases,
turn off ADLC.
PD-M550/PD-M455
PD-M450/PD-M453
ADLC
C22]
NOTES (PD-M550/PD-M455/PD-M453
only}:
• The setting of the OUTPUT LEVEL buttons am canceled when
ADLC is turned on.
• When ADLC is turned on, the OUTPUT LEVEL buttons cannot be
opera ted.
]3
<PRB1142>
En
TO PLAYONLYDESIREDTRACKS/DISCS
I
I
PD-M550
1,3 3
r fin
Pr°graln
des !! edplayback"
order
T° pr°gram tracksldiscs
i
1
2
53
PD-M455
(PD-M453/
PD-M450)
2
*
During stop mode, press the Program button.
The PR( IGRAM indicator lights.
Press
;he Disc number
button
which contains
1,3 3
R_
o
3
*: PD-M455/PD-M453
**: PD-M455 only
1
Press _
5
PGM
DISC3
DSC4
D_SC5
so that the desired
track
No.
DISC6_
Repea t steps
programmed.
2
and
3
for
other
tracks
to
be
Press I_.
The t_a_ks are played in the programmed order. When all
programi'ned tracks have been played the payer enters stop
mode.
I
IDISC2
button
button aan be used.
Enter the desired track No. with the TRACK NUMBER/Digit
button. IInthis case, it is not necessary to press PGM.
PD-M455(PD-M453/PD-M450)
4
DISC1
or _
appearF on the display and press the Program button.
For PD-M550 only:
Instead of the _
or _
button, the TRACK NUMBER/Digit
only
PD-M550
the
track_
be programmed.
To prog am entire discs, enter the desired disc numbers with
the Disc number buttons and go to step 4.
• Whe_ the Disc number button is pressed, "AL" (all tracks}
appears on the display.
8
2
3
To stopP •ogram playback:
Press II.
F-_ E--I F-7
DISC NUMBER
4
5
6
EEl3r-Z EEl
Program
To go;to
I_1.
•
To ente_ track No. 11 or above with the TRACK NUMBERIDigit
buttons, lsee "Track Search" on page 11.
Each tinge a track is programmed, the display will show the
progremrned number.
#
I, the m)gazine is in the player, the program contents will not
be erased even if the power is turned off.
•
PD-M550
•
-, {c q
containing up to 32 steps can be created.
the previous or next step in a program, press 14t1<1
or
•
•
I
or
TRACK
NUMBER
©@P-l@
@@41@
Programm!ng while listening to playback (PD-M550 only)
During no_mal playback or program playback, you can program the
desired trac4ks. Enter the disc No, and track No. with DISC NUMBER
and TRACK_ NUMBER
PROGRA_indicator
buttons during program mode. (While the
lights,)
NOTE:
During Delete programming or Time fade editing the Program button
,"F
PD-M455(PD-M453!PD-M 450)
TRACK SEARCH
•
For PD-M550 or PD-M455,the PGM and I<_/l_J-I buttons on
the remote control unit can also be used.
cannot be dperated.
i
Direct Program
During normal playback or Magazine Hi-Lite Scan playback, the track
being playe_l can be programmed.
1. Press _h_eProgram button to enter the program mode.
2. To searqh for a desired track during normal playback, it is possible
to skip t(p succeeding tracks by pressing _
or _
button. Also,
Magazin!e Hi-Lite Scan function can be used to move from track to
track thrpugh the disc.
3. If you Wish to program the track currently playing, press the
Progra_ button while the track is playing.
• Direct plogramming is not possible during program playback,
PLAY
[,mmm'e',J
k,,
)4
<PRB1142>
En
TO PLAY ONLY DESIRED TRACKS/DISCS
I Programming
i
I
a pause
Inserting a pause in your program can be very useful when carrying
out recording. Press II instead of entering a track number. "PA"
appears on the display panel.
• For example, when recording on both sides of a cassette tape,
if you p_ogram a pause after the last track to be recorded on
the first side, program playback will pause at that point to allow
you to switch tape sides. To resume program playback after the
player enters pause mode, press II.
Notes:
I
gp
A pause inserted in a program is counted as one step.
If a pause [s programmed as the last step of a program,
player will not enter the pause mode.
I To clear all of the program contents
®
£1
@@
I
i
CHECK
the
-_
During program mode, set the ptayer to stop mode and press
CHECK. The prpgram contents will be displayed in the programmed
order,
•
After confi_fming the last program step, the display will show
"O-O0"
,,,,
i
CC]
(_)
®
P-
@
3-D'V
P- 0_
@ @ @@
"
SlOP
®
i-u9
@
"_
I@ .....
s A pause can be programmed only when the program pn_cedure
is performed under stop mode.
• A pause cannot be programmed at the beginning of a program
(P-01), and two pauses cannot be programmed one after the
other.
•
•
[
"[ -.... I
To checkithe program contents (PD-M550/
PD-M455/PD-M453 only)
I To
modi_ithe
program
contents (PD-M550/PDM455/PD-M453
only)
D
,_
@
@
@ @
PD-M550
During stop mode, press e.
When the magazine is ejected, the program contents
cleared.
will be
5
7
DISC
NUMBER
TRACK
NUMBER
PD-M455/pDiM453
..,.o 'Aac",r
I To
erase
a program
M453
only)
(PD-M550/PD-M455/PD-
F-7
CLEAR
TRACK
....
,_ ECI
-"-
P- 2
t
CLEAR
During program mode, set the player to stop mode and press
CHECK so that the program step to be corrected appears on
the display,
2. To correct th disc NO., enter the new disc No. with the DISC
NUMBER bu tons. For PD-M550, enter the new track No. with
the TRACK I JUMBER/Digit buttons.
For PD-M45B/PD-M453,
dPress
_1so that the the new disc No, appears on the
isplay. For )xample.: the programmed track No. 4 on the disc
No. 3 is cha iged to track No. 7 on the disc No, 5, using the
DISC NUMB -_R5 button and TRACK NUMBER 7 button (PDM550), or I_ I/1_ and PROGRAM (PD-M455/PD-M453).
Repeat steps 1 and 2 to change other tracks as desired.
For PD-M55C the _
or _
button can also be used to correct
the track No After selecting the track No., be sure to press
PGM
1,
During program mode, press CLEAR on the remote control unit.
The last program step is erased and the contents of the previous
program step are displayed.
NOTE:
Contents of a program can be erased during playback as well.
However, tracks preceding the currently playing track cannot be
erased in this way.
15
<PRB1142>
En
TOPLAY
ONLY DESIRED TRACKS/DISCS
(Program
Playback and Delete Program
_layback)
I
2
1.3 3
- To delete
Delete[ program playback
undesi_d tracks/discs
PD-M550
'1
1
2
5 3
PD-M455(PD-M453/PD-M450)
•
li2
° =
*: PD-M455iPD-M453
3
only
**: PD-M455 only
1
During stop mode, press DELETE.
The DELETE indicator lights,
Press,the
Disc number button
which contains
the
track to be deleted.
To dateta entire discs, enter the desired disc numbers with the
Disc nqmber buttons and go to step 4.
When the Disc number button is pressed, "AL" (all tracks)
appears on the display.
Press il<HI or _
button so that the track No. to be
del_d
appears on the display and press DELETE.
For PDI-M550 only:
Instea d of the _
or IHH button, the TRACK NUMBER/Digit
buttoncan
be used.
Enter the desired track No. with the TRACK NUMBER/Digit
button.[ In this case, it is not necessary to press DELETE.
Repeat steps 2 and 3 for other tracks to be deleted.
5
PD-M550
**
PD-M455(PD-M453/PD-M450)
4
5
APl_eral_cl_s
other than deleted trackstdiscs are played in the order
of the disc and track numbers. When tracks have been played,
the player enters stop mode.
To stopD_lete
Press R.
•
2
1
_
3
E2:31:2:-IEZ:]
D!SC NUMBER
F,sc_ID,sc
2 lo,sc3 ID,sc,ID,sc
s I_Jsc.
•
DISC NUMBER
2)
3
To enter track No. 1! or above with the Track number/Digit
buttone, jsee "TraCk Search" on page 11.
Tracks tq be deleted should be selected between track No, 1 and
track Noi 32,
If the magazine is in the player, the Delete Program contents will
not be e!ased even if the power is turned off.
•
]
program playback:
NOTE:
If the Program procedure has been performed,
cannot be carried out.
Delete programming
PD-M550
I _,-, I ,-_ IJ
i
/?
/?
To clea_ all of the delete program contents
i
or
I ESd C5
TRACK NUMBER
7
F-I[-3[Z3
8
9
TO
[Z E:::3C3 EZ]
[l,
/?
®
/9
PD-M455 (PD_M453iPD-M450)
TRACK SEARCH
DELETE
_
z:::::31
®
PD-M550/PD*M455/PD-M453
only
CLEAR
EC3
•
For PD-M550, PD-M455 or PD-M453, the DELETE and
buttons on the remote control unit can also be used.
pLAY
0 /9
1G
<PRB1142>
En
(_) During siop mode_ press II.
® When thhe magazine
cleared.
is ejected, the program contents
will be
(_ Press CL+EAR on the remote control unit during stop mode or
play mo_e, When CLEAR is pressed during Delete Program
playbaCkJmode, the player enters normal playback mode. (PDM550/PD-M455/PD-M453
only)
I CONVENIENTOPERATIONFOR RECORDING
i
Compu program editing (Computer allocated
program editing)
1,3
PD-M550
I
Tracks are selected for both sides of the tape,
3
3
PD-M455 (PD-M453/
PD-M450}
,3
•%T=
*: PD-M455/PD-M453
**: PD-M455 only
only
1
During
2
3
Select the disc No. with the Disc number button.
Press _
or _
so that the desired
playing time
appears _n the display and press COMPU PGM EDIT.
Each time _
is pressed, the time will be changed inthe following
sequence: 46 *-* 54--p 60 --* 74--* 90 (m inutes). With _,il_l,the time
wilt be chaniged in the reverse direction.
For PD-M550 only:
instead of !the _
or _
button, TRACK NUMBER/Digit
buttons {_J - _1} can be used.
Press the 1O's digit button and l's digit button sequentially. To
enter 9 minutes or tess, press _ and then the corresponding digit
button.
stpp mode,
press COMPU
PGM
EDIT•
The displayed time is memorized. The player now programs the
tracks for the first side of the tape within half the selected playing
time, programs a pause, and then programs the tracks for the
second side iof the tape within half the selected playing time. After
the programming is completed,
the display shows all of the
programmed tracks and their praying time in the programmed
order.
Example: The tape playing time 46 minutes is selected.
• The programmed contents are displayed in the programmed
order.
DISC NUMBER
[I :,is__lD_sc2I_sc3 I o_sc_t _lscs I oJsc_q)
OISC NUMBIER
First side
/?
•
,
,
_b-
--
lr--cJu
Second side
3
PD-M550
I
_
I
'_
II
/¢
NOTES:
• Up to 32 steps can be programmed,
• With discs cbntained 24 tracks or more, programming may not
be correctly performed.
• if the selected time is too short for any track to be programmed,
programming cannot be performed.
• tf you wish t& enter the time with the digit buttons after the time
is already entered with _
or _
in step 3, press _]
or
[_
, The dfgit buttons cen now be operated (PD-M550 only).
• [f the magaZine _s in the player, the contents of the Compu
program editing will ndr be erased even if the power is turned oif.
TRACK NUMBER
_"
4
5
8
_
L C2 [2
PD*M455
(PD-M453/PD-M450)
TRACK SEARCH
,,,
/9
•
/?
For PD-M550, PD-Mt,55 or PD-M453, the I-_<ii-I_
remote control unit can also be used.
button
on the
]7
<PRB1142>
En
CONVENIENT
OPERATION FOR RECORDING
(Compu
Program
1,3
PD-M550
INN
Editing/Time
Fade !Editing/One-touch
I Time
Fade)
f_de editing
Tracks arelselected within the specified time and playback pauses
with a fad,-out.
i
Jg"-'='-N
3
.2
PD-M455 (PD-M453t
PD-M450)
1
2
During stop mode, press TIME FADE EDIT.
Select the disc No. with the Disc number button.
3
Press I<<
3
1,3
•%T-=
*: PD-M455iPD-M453 only
**: PD-M455 only
PD-M455 (PD-M4531PD-M450)
I
so that
the
desired
playing
time
Press the 10's digit button and 1's digit button sequentially. To
ente_ 9 minutes Or less, press [] and then the corresponding digit
burton.
The displayedtime ismemorlzed. The playernow programs the
trackswithinthe selectedplayingtime.
*,
PD-M550
or _
i
appears on the display and press TIME FADE EDIT.
Each time _
is pressed, the time will be changed in the following
sequence: 23 _ 27 "* 30 --_37 ---*45 (minutes). With I_1_1,the time
will be Changed in the reverse direction.
For PDI-M550 omly:
Instea d of the _
or _
button, the TRACK NUMBER/DIgit
buttonls (m - _bl)can be used.
T, MEFADE
I1
NOTES:
•
•
DISC NUMBER
I msc11msc2 IDisc3 Imsc4 I D)SC
SI ms__ II
/f
DISC NUMBER
z7
•
•
If Random playback, Track Search, Disc Search or Magazine HiLite SCan is done during Time Fade Editing play, Time Fade
Editing will be cleared.
If a tape playing time beyond the total playing time is selected,
the player cancels the Time Fade Edit mode and enter stop
mode after the specified disc is played.
During Time Fad_ operation, programming for Program Playback/
Delete Program Playback cannot be carried out,
If the magazine Js in the player, the contents of the Time Fade
Editing will not be erased even if the power is turned off.
PD-M550
or
TRACK NUMBER
= cbcbcb@
@cbcb#S
cbdhr
PD-M455 (PD-M453/PD-M450)
TRACK
II
•
SEARCH
I
One-touch
II
For PD-M550, PD-M455 or PD-M453, the _
remote control unit can also be used.
®
®
button
on the
fade
Playbac_ can be started from the desired point with a fade-in and
stopped _tithe desired point with a fade-out.
• The Qne-touch Fadefunctioncan becarried outin Normal playback,
Program playback/Delete Program playback, Random playback or
Magazine Hi-Lite Scan mode.
Set the player to the desired playback mode, and then perform
the foil@wing procedure.
(_) During pause mode, press AUTO FADER. The FADER indicator
flashes iand playback starts with a fade-in.
(_) During iplaybacki press AUTO FADER. The FADER indicator
flashes iand playback pauses with a fade-out.
•
18
<PRB1142>
En
For PD!M455 and PD-M453, the FADER button on the remote
control Unit can also be used.
I
TROUBLESHOOTING
i
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check
the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being
used.
If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest PI(ONEER authorized service center or your
dealer to carry out repair work.
Probable cause
Symptom
Remedy
Connect plug to amp(ifier or wall outlet.
when
•
Power plug is disconnected
When playback is started, it stops
immediately.
Pauses or stops
during playback.
•
Disc is loaded upside down.
•
•
Smudged on the disc, etc.
•
o
Output cords are connected
incorrectly
Ioose(y.
Incorrect operation of stereo amplifier.
Magazine is not expelled
EJECT button is pressed.
No sound
from outlet,
or
Pin plugs and/or amplifier terminals are dirty.
Player is in pause mode,
Load the disc correctly with the label side
DOWN.
Clean the smudges from the disc and then
play it again,
I
Connect properly.
•
Check the settings of amplifier switches
sound volume controls.
• Clean away dirt.
m Pressthe im-button.
and
I
Incorrect conne_ions.
D Connect to amplifier's AUX or CD terminals.
Do not connect to PHONO terminals.
o
Pin plugs and/or amplifier terminals are dirty:
Interference is being picked up from a *IV set.
e Clean,way dirt.
m Switch OFF TV set, or move player away from
TV set.
With certain discs, loud noise is
produced, or play stops.
•
•
Disc has bad scratch or warp.
Disc is extremely dirty.
im ReplaCe the disc.
a Clean idiso.
The picture of the TV screen
fluctuated
or FM broadcast
interfered with noise,
•
Interference is being picked up from the CD
player.
e
•
•
Dead batteries.
Too far from player or wrong angle.
e
e
•
Obstruction between player and remote control
unit.
Sound is distorted,
noise is output.
i
is
is
Remote control will not function.
(PD-M 550/PD-455/PD*M453 only)
Turn &ff POWER of the player, or move the
player away from TV or tuner,
Replace batteries.
The distance between remote control unit and
player should be no more than about 7 meters.
The operational angle against the front panel
is within 30" from right or left end of player.
a Relocate remote control
unit or remove
obstruiction,
]9
<PRB1142>
En
!
SPECIFICATIONS
i
1. General
Type ..........................................
Compact disc digital audio system
Power requirements
European models ................................ AC 220 -230 V, 50/60 Hz
U.K. and Australian models ...................... AC 230 -:240 V, 60 Hz
U.S, and Canadian models ................................ AC 120 V, 60 Hz
Other models ............ AC 110/120 - 127/220/240 V (switchable),
50/60 Hz
Power consumption ......................................................
Operating temperature ................................................
12 W
÷5"C - +35*C
(+41 °F - +95°F)
3.9 kg (8 Ib, 10 oz)
Weight ................................................................
External dimensions
PD-M550 ..................................... 420(VVJX 291(D) X 101(H) mm
16-9/16(W) X11-7/16(D) X 4{H) in
PD-M455/PD-M453/PD-M450
...... 420(W} X 291 (D) X 96(H) mm
16-9/16(W) X 11-7/t 6(D) X 3-12/16(H) in
Repeat functions
• 1 traokrepeat
• All discs repeat
• Prog_m repeat
• Random play repeat
• Delete play repeat
• Deleterandom play repeat
• Magazine Hi-Lite scan repeat
Random play
• Random p ey (repeat also available)
• Delete random play (repeat also available)
Switching display
Time consumed i remaining time (track!disc), and total time
Timer start
ADLC
2. Audio section
Frequency response ..................................................
2 Hz - 20 kHz
S/N ratio ..............................................
102 dB or more (EIAJ)
Dynamic range .......................................
96 dB or more (EIAJ}
Harmonic distortion ................................
0.003% or less (EIAJ)
Output voltage .........................................................................
2.0V
Wow and flutter ............................................
Limit of mesurement
L+-0.001% W.PEAK) or less (EIAJ)
Channels .............................................................
2-channel (stereo)
Digital level controller PD-M550/PD-M455/PD-M453
Volume control _an be done.
only)
One-touch fade
Fad_n and fade-out possible.
Time fade edit[ng
Selects the tracks within the specified time. Playback pauses
with a fade-out. !
3. Output terminal
Audio line output
Headphone jack with
Control input]output
and Canadian models
available with models
CD-DECK SYNCHRO
volume control (PD-M550/PD-M455 only)
jacks (available with the PD-M450 and U.S.
of the PD-M550, PD-M455 end PD-M453: Not
for military zones (multi-voltage types))
jack
Compu prbgram e_iting
Selects the tracks for both sides within the specified time.
Power ON/OFF function
M550/PD_M455/PD-M453
J
Automa_o
(remote
only)
control unit provided with
PD-
Power On
4. Functions
Number of discs to be stored - maximum 6.
Power Down Eject
Basic operation buttons
• PLAY, PAUSE, STOP
5. Accessories
•
Remote control unit (PD-M550/PD-M455/PD-M453
•
Size _RO3/d_
batteries
(PD-M550/PD-M455/PD-M453
only) ........................................ 2
Six-compact-disk magazine ......................................................
1
Control cord (pi'ovided with PD-M450 and U.S. and Canadian
models of PD-MBsB/PD-M455/PD-M453
only: Not available with
models for military zones (multi-voltage types)) ....................... 1
Output cable -..i .........................................................................
1
Operating instrqctions ..............................................................
1
Search function
• Disc search
• Track search
• Manual search
•
•
Magazine Hi-Lite Scan
• DISC SCAN
• TRACK SCAN
•
•
onlyl ....... 1
NOTE:
Programming
• Maximum 32 steps
• Pause
•
•
•
Specifications and idesign subject to possible modification
notice, due to imptrovements.
Program check!correction (remote control unit provided with
PD-M550/PD-M455/PD-M453
only)
Program clear (single track or all tracks) (remote control unit
provided with PD-M550/PD-M455/PD-M453
only)
Delete play
without
The Magazine
Type Multi-Play
CD Players with
mark and the Magazines
with the same
mark are compatible
for 5-inch
(12cm) discs.
Published
Copyright
All rights
by Pioneer
Electronic
Corporation.
© 1991 Pioneer
Electronic
Corporation
reserved.
i
PIONEER
PIONEER
PIONEER
PIONEER
PIONEER
ELECTRONIC
CORPORATION
4-1,Meguro
1-Chome, M_Llro*ku, Tokyo153, Japan
ELECTRONICS [USA] INC.
2265 East 220th Street, Long Beach, California 913810U.S.A.
P.O. BOX 1720, Long Beach. California 90801, U,S.A.
ELECTRONICS OF CANADA, INC.
505 Cochrane Drive, Markham, Ontario _3R 8E3, Canada
ELECTRONIC [EUROPE] N.V.
Keetberglaan1, 9120 Beveren, Belgium, TEL 03/750.05;11
ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside,Vi_toria 3195, Australia, TEL: [03] 580-9911
(92BO2WF7D16>
Printed in Japan <PRB1142-B>