Download Pioneer Mixer DJM-900SRT User's Manual

DJ MIXER
DJM-900SRT
DJM-900SRT Serato DJ Edition
http://pioneerdj.com/support/
The Pioneer DJ support site shown above offers FAQs, information on software and various other types of
information and services to allow you to use your product in greater comfort.
http://serato.com/
For the latest version of the Serato DJ software, access Serato.com and download the software from there.
Quick Start Guide – Serato DJ Edition
Contents
Before start
With the DJM-900SRT, the four decks (players) provided in the Serato DJ software
can be controlled (stereo audio signals can be input/output simultaneously to/
from four sets of inputs and four sets of outputs) and sound can be input/output
using the built-in USB sound card, so various types of DJ performances in combination with the Serato DJ software are possible simply by connecting the unit to
a computer with a single USB cable. The DJM-900SRT also supports recording,
creation of tracks, etc.
Furthermore, digital music files can be operated with your favorite analog player
(turntable) or DJ player using the Serato DJ software and the included control
discs 1.
1 A special CD and record containing the signals necessary for operating digital
music files.
! Software version 1.5.0 or later is required to connect and use this unit with the
Serato DJ software.
! In this manual, names of channels and buttons indicated on the product, names
of menus in the software, etc., are indicated within square brackets ([ ]). (e.g.
[MASTER] channel, [ON/OFF], [File] menu)
! Please note that the screens and specifications of the software described in this
manual as well as the external appearance and specifications of the hardware
are currently under development and may differ from the final specifications.
! Please note that depending on the operating system version, web browser settings, etc., operation may differ from the procedures described in this manual.
! Be sure to read both this leaflet and the operating instructions! Both documents
include important information that you must understand before using this
product.
Launching the Serato DJ software
Before installing the Serato DJ software.........................................................................3
Installing the Serato DJ software.....................................................................................3
Launching the Serato DJ software...................................................................................4
Installing the driver software............................................................................................5
Names of parts of the Serato DJ software.......................................................................6
Controlling the Serato DJ software
Before controlling the Serato DJ software......................................................................7
When using analog players..............................................................................................8
When using DJ players.....................................................................................................9
When using analog players and DJ players simultaneously.......................................10
Checking the control signals..........................................................................................11
Selecting the play mode..................................................................................................11
Importing or loading tracks............................................................................................11
Playing tracks...................................................................................................................11
Quitting the system.........................................................................................................11
2
En
Before installing the Serato DJ software
Serato DJ is a DJ software application by Serato. DJ performances are possible by
connecting the computer on which this software is installed to this unit.
! The user is responsible for preparing the computer, network devices and other
elements of the Internet usage environment required for a connection to the
Internet.
! For details on operating the Serato DJ software, see the Serato DJ software
manual.
For the Serato DJ software manual and information on the latest version of the
Serato DJ software, see [Software Info] under [DJM-900SRT] on the Pioneer
DJ support site below.
http://pioneerdj.com/support/
Cautions on Installation
! Before installing the Serato DJ software, turn this unit’s power switch off and
disconnect the USB cable connecting this unit to the computer.
! If installation of the Serato DJ software is interrupted, follow the procedure
below to start installation over from the beginning.
! Before installing the Serato DJ software, quit all other programs that are running
on the computer.
! The driver software is compatible with the following OSs.
Minimum operating environment
Supported operating systems
Mac OS X: 10.6.8, 10.7.5
and 10.8
32-bit version
64-bit version
32-bit version
Windows: Windows 7
1 Insert the CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
! If the CD-ROM menu does not appear when the CD-ROM is inserted, open the
CD drive from [Computer (or My Computer)] in the [Start] menu, then doubleclick the [CD_menu.exe] icon.
2 When the CD-ROM’s menu appears, select [Download
Serato DJ Software.], then click [Start].
3 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
[Serato DJ Support Information] is displayed.
5 Click the link to the Serato DJ download page.
Intel® processor, Core™ 2 Duo 2.4 GHz or better
4 GB or more of RAM
®
Intel processor, Core™ 2 Duo 2.0 GHz or better
2 GB or more of RAM
Intel processor, Core™ 2 Duo 2.4 GHz or better
4 GB or more of RAM
Display resolution
Resolution of 1 280 x 720 or greater
Internet connection
An Internet connection is required for registering the “Serato.
com” user account and downloading the software.
!
! Log on as the user which was set as the computer’s administrator before
installing.
! If any other programs are running on the computer, quit them.
1 GB or more of RAM
A USB 2.0 port is required to connect the computer with this
unit.
!
Do not connect this unit and the computer until installation is completed.
®
Intel processor, Core™ 2 Duo 2.0 GHz or better
USB port
!
Installation Procedure (Windows)
4 Click [Software Info] under [DJM-900SRT] on the Pioneer DJ
support site.
Others
!
Installing the Serato DJ software
CPU and required memory
®
64-bit version
Launching the Serato DJ software
Launching the Serato DJ software
For the latest information on the required operating environment and compatibility as well as
to acquire the latest operating system, refer to “Software Info” under “DJM-900SRT” on the
Pioneer DJ support site below.
http://pioneerdj.com/support/
Operation is not guaranteed on all computers, even if all the required operating environment
conditions indicated here are fulfilled.
Depending on the computer’s power-saving settings, etc., the CPU and hard disk may not
provide sufficient processing capabilities. For notebook computers in particular, make sure
the computer is in the proper conditions to provide constant high performance (for example
by keeping the AC power connected) when using Serato DJ.
Use of the Internet requires a separate contract with a provider offering Internet services and
payment of provider fees.
The Serato DJ download page is displayed.
6 Log in to your “Serato.com” user account.
! If you have already registered a user account on “Serato.com”, input the registered e-mail address and password to log in at “Serato.com”, then proceed to the
Serato DJ software download page.
Proceed to step 8.
! If you have not completed registering your user account, do so following the
procedure below.
— Following the instructions on the screen, input your e-mail address and the
password you want to set, then select the region in which you live.
— If you check [E-mail me Serato newsletters], newsletters providing the
latest information on Serato products will be sent from Serato.
— Once user account registration is completed, you will receive an e-mail at the
e-mail address you have input. Check the contents of the e-mail sent from
“Serato.com”.
! Be careful not to forget the e-mail address and password specified when you
performed user registration. They will be required for updating the software.
! The personal information input when registering a new user account may be collected, processed and used based on the privacy policy on the Serato website.
7 Click the link in the e-mail message sent from “Serato.com”.
Proceed to the Serato DJ software download page.
8 Download the Serato DJ software from the download
page.
Unzip the downloaded file, then double-click the unzipped file to launch the installer.
9 Read the terms of the license agreement carefully, and if
you agree, select [I agree to the license terms and conditions],
then click [Install].
! If you do not agree to the contents of the license agreement, click [Close] to
cancel installation.
En
3
Installation begins.
10Read the terms of the license agreement carefully, and if
you agree, click [Agree].
The message of successful installation appears once installation is completed.
10Click [Close] to quit the Serato DJ installer.
! If you do not agree to the contents of the usage agreement, click [Disagree]
to cancel installation.
11If the following screen appears, drag and drop the [Serato
DJ] icon on the [Applications] folder icon.
Installation procedure (Mac OS X)
Do not connect this unit and the computer until installation is completed.
! If any other programs are running on the computer, quit them.
1 Insert the CD-ROM into the computer’s CD drive.
The CD-ROM menu is displayed.
! Double-click the CD icon on the desktop when folders are not displayed after a
CD-ROM has been loaded.
2 Double-click [CD_menu.app].
3 Select [Download Serato DJ Software.] from the CD-ROM’s
menu, then click [Start].
4 “An internet environment is required to access the site.
Connected to the internet?” is displayed. Click [Yes].
The web browser is launched and the Pioneer DJ support site is displayed.
5 Click [Software Info] under [DJM-900SRT] on the Pioneer DJ
support site.
[Serato DJ Support Information] is displayed.
6 Click the link to the Serato DJ download page.
The Serato DJ download page is displayed.
7 Log in to your “Serato.com” user account.
! If you have already registered a user account on “Serato.com”, input the registered e-mail address and password to log in at “Serato.com”, then proceed
to the Serato DJ software download page.
Proceed to step 9.
! If you have not completed registering your user account, do so following the
procedure below.
— Following the instructions on the screen, input your e-mail address and
the password you want to set, then select the region in which you live.
— If you check [E-mail me Serato newsletters], newsletters providing the
latest information on Serato products will be sent from Serato.
— Once user account registration is completed, you will receive an e-mail at
the e-mail address you have input. Check the contents of the e-mail sent
from “Serato.com”.
! Be careful not to forget the e-mail address and password specified when you
performed user registration. They will be required for updating the software.
! The personal information input when registering a new user account may
be collected, processed and used based on the privacy policy on the Serato
website.
Launching the Serato DJ software
1 Turn on this unit’s power.
2 Connect this unit to your computer via a USB cable.
3 Launch the Serato DJ software.
! For Windows
From the Windows [Start] menu, click the [Serato DJ] icon under [All
Programs] > [Serato] > [Serato DJ].
! For Mac OS X
In Finder, open the [Applications] folder, then click the [Serato DJ] icon.
! Computer screen when launching the Serato DJ software
This is the screen displayed when the DJM-900SRT and computer are connected, before the driver is installed.
— When Serato DJ is launched the first time, an [BUY/ACTIVATE] icon may be
displayed in the license panel, but there is no need for DJM-900SRT users to
activate the software or purchase the license.
8 Click the link in the e-mail message sent from “Serato.com”.
Proceed to the Serato DJ software download page.
9 Download the Serato DJ software from the download
page.
Unzip the downloaded file, then double-click the unzipped file to launch the installer.
4
En
1
1 License panel
Installing the driver software
Launching the Serato DJ software
This driver software is a special driver software for inputting and outputting audio
signals from the computer.
Cautions on Installation
! If installation of the driver software is interrupted, follow the procedure in the
“Installing device driver software” section of this unit’s operating instructions
to start installation over from the beginning.
! Before installing the driver software, terminate all other programs running on
your computer.
! For information on the latest version of the driver software, see [Software Info]
under [DJM-900SRT] on the Pioneer DJ support site below.
http://pioneerdj.com/support/
Installation Procedure
Click the [INSTALL DRIVER] button on the Serato DJ software
screen.
Following the instructions displayed on the screen, install the driver software.
! When installing the driver software before connecting the devices, installation is
performed in a different way.
For details, see this unit’s operating instructions.
En
5
Names of parts of the Serato DJ software
Computer screen when the Serato DJ software and this unit are connected
This screen is an example of the screen displayed after the driver software is installed, with the computer and this unit connected and tracks loaded in the respective decks.
1
2
1
3
1Deck section
The track information (the name of the loaded track, artist name, BPM, etc.), the overall waveform and other information is displayed here.
2Waveform display
The loaded track’s waveform is displayed here.
3Browser section
Crates in which tracks in the library or sets of multiple tracks are stored are displayed here.
! This manual consists mainly of explanations of functions of this unit as hardware. For detailed instructions on operating the Serato DJ software, see the Serato DJ software manual.
The Serato DJ software manual can be downloaded from the Pioneer DJ support site below.
See [Software Info] under [DJM-900SRT].
http://pioneerdj.com/support/
Computer screen when the Serato DJ software and this unit are connected (setup screen)
This is the Setup screen displayed when the computer and this unit are connected after installing the driver software.
1
2
1
1CALIBRATION DECK
The Serato DJ software calculates analog signals from the control disc and processes the signals of digital audio files.
Different signal levels and device statuses can be calculated for each usage environment to make the optimum settings for reading out the control signals.
2Utility settings
Utility settings such as settings affecting the entire system and detailed operation settings can be made here.
6
En
Controlling the Serato DJ software
The signals played on the Serato DJ software’s decks [DECK1] to [DECK4] are input to
this unit’s respective channels.
The combinations of the decks and the respective channels to which the sound is
input are fixed. These combinations are shown below.
Correspondence table of Serato DJ software decks and DJM900SRT channels
Serato DJ software deck
DECK3
DECK1
DECK2
DECK4
DJM-900SRT channel
CH1
CH2
CH3
CH4
Set the positions of the controls, etc., as shown below.
MASTER
CD/ LINE PHONO
DIGITAL
USB
CD/ LINE PHONO
DIGITAL
USB
DECK 3
1
CD/ LINE PHONO
DIGITAL
USB
DECK 1
1
CD/ LINE PHONO
DIGITAL
USB
DECK 2
1
LEVEL
DECK 4
1
0
TRIM
TRIM
OVER
2
10
7
7
9
7
9
OVER
2
10
HI
4
TRIM
OVER
2
10
HI
4
TRIM
OVER
7
9
HI
4
2
2
1
1
1
1
0
-26 /
-1
6
-1
MID
-2
0
-26 /
6
-1
MID
-2
EQ/
-3
-5
- 7 -26 /
-5
- 7 -26 /
6
LOW
-10
-5
- 7 -26 /
6
LOW
-10
-10
-10
-15
-24
-24
-24
-24
dB
dB
dB
dB
3
COLOR
6
3
COLOR
4
LOW
-26 /
6
4
HI
LOW
CUE
-10
-24
-26 /
LOW
CUE
L
6
3
COLOR
dB
BALANCE
HI
LOW
CUE
HI
L
CUE
R
CUE
MONO
10
10
10
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
2
1
1
1
0
A
THRU B
5
6
0
A
THRU B
5
6
A
THRU B
STEREO
BOOTH MONITOR
0
EQ CURVE
ISOLATOR EQ
0
5
6
R
4
4
HI
-7
-15
3
COLOR
-5
6
LOW
-15
-26 /
Turned fully counterclockwise
-3
ISO
-15
6
[THRU] position
MASTER LEVEL control
-2
EQ/
-15
-26 /
Moved forward
CROSS FADER ASSIGN (A, THRU, B) selector switch
-1
MID
- 7 -26 /
6
Center
Channel faders
0
6
-5
LOW
Center
COLOR control
1
-26 /
-3
ISO
Turned fully counterclockwise
EQ/ISO (HI, MID, LOW) controls
4
-2
EQ/
-3
ISO
USB
TRIM control
2
-1
MID
-2
EQ/
-3
ISO
6
Position
Input selector switch
7
9
0
-26 /
10
HI
4
2
0
2
10
2
7
OVER
Names of controls, etc.
Controlling the Serato DJ software
Before controlling the Serato DJ software
A
THRU B
5
6
CH FADER
1Input selector switch
2TRIM control
3EQ/ISO (HI, MID, LOW) controls
4COLOR control
5Channel faders
6CROSS FADER ASSIGN (A, THRU, B) selector switch
7MASTER LEVEL control
En
7
Here we explain three types of connections for different usage environments.
! When using analog players, proceed to page 8.
! When using DJ players, proceed to page 9.
! When using analog players and DJ players simultaneously, proceed to page 10.
When using analog players
Here we explain connections for using the Serato DJ software’s decks [DECK1] and [DECK2] connected to analog players.
Audio cable
Audio cable
Ground wire
Ground wire
L R
L R
CH 4
CH 3
PHONO CD/ LINE
R
POWER
OFF
ON
PHONO CD/ LINE
L
L
RETURN
L (MONO)
CH 2
PHONO CD/ LINE
L
MIC2
R
MASTER1
R
L
R
MASTER2 REC OUT
L
L
R
AC IN
1 GND
MIDI OUT
SIGNAL GND
R
SEND
L (MONO)
R
PHONO CD/ LINE
L
SIGNAL GND
Analog player
CH 1
R
2 HOT
3 COLD
DJM-900SRT
R
BOOTH
CH2
TRS
R
L
LINK
DIGITAL
MASTER
OUT
CH4
CH1
Analog player
IN
CH3
USB cable
CONTROL VINYL
CONTROL VINYL
To amplifier
To power outlet
Computer
1 Connect the analog player that will be controlling [DECK1]
to the [CH2] [PHONO] terminals, the analog player that will be
controlling [DECK2] to the [CH3] [PHONO] terminals.
2 Connect the ground wires for the respective analog players
to this unit’s [SIGNAL GND] terminals.
3 Set the CONTROL VINYLs on the analog players.
4 Switch the DJM-900SRT’s input.
Switch the [CH2] and [CH3] input selector switches to [USB].
Input selector switch
CD/ LINE PHONO
DIGITAL
USB
CD/ LINE PHONO
DIGITAL
USB
DECK 1
DECK 2
TRIM
TRIM
POWER
MIC
USB
MASTER
CD/ LINE PHONO
DIGITAL
USB
MIC1
CD/ LINE PHONO
DIGITAL
USB
DECK 3
CD/ LINE PHONO
DIGITAL
USB
DECK 1
CD/ LINE PHONO
DIGITAL
USB
DECK 2
MIDI
START
/ STOP
ON/ OFF
LEVEL
DECK 4-
LFO FORM
WAKE UP
UTILITY
BEAT EFFECTS
0
TRIM
TRIM
OVER
OVER
10
MIC 1
LEVEL
1
0
1
0
12
12
6
LOW
- 7 -26 /
12
TALK
OFF ON OVER
-10
- 7 -26 /
6
DUB
ECHO
SPACE
- 7 -26 /
6
dB
COLOR
GATE/
COMP
dB
6
-5
-7
6
LOW
-10
-10
-15
-24
-26 /
COLOR
dB
6
BEAT
-15
-24
-26 /
X- PAD
-3
ISO
- 7 -26 /
6
-15
-24
6
-1
-2
EQ/
-5
LOW
-10
-15
-26 /
6
MID
-3
ISO
%
ms
0
-26 /
-1
-2
EQ/
-5
LOW
-10
-15
-24
dB
ISO
-5
LOW
6
MID
-3
-24
-26 /
COLOR
6
L
dB
R
AUTO
/ TAP
CRUSH
FILTER
CUE
LOW
LINK
HI
LOW
CUE
HI
LOW
CUE
HI
LOW
CUE
HI
CUE
L
R
FLANGER PHASER
FILTER
ROBOT
CUE
TRANS
3
STEREO
STEREO
10
10
10
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
1
CF.A
CF.B
1
MASTER
EQ CURVE
ISOLATOR EQ
0
MASTER
LEVEL / DEPTH
A
THRU B
A
THRU B
A
THRU B
A
THRU B
CH FADER
MIN
0
CROSS FADER
CROSS FADER ASSIGN
PHONES
A
En
2
TIME
1
0
MIC
0
2
1
0
BOOTH MONITOR
MIDI LFO
SND/ RTN
4
3
LEVEL
8
REV ROLL
DELAY
MIXING
CUE
ECHO
4
HEADPHONES
MONO SPLIT
SLIP ROLL
ROLL
SPIRAL
MONO
2
MELODIC
REVERB
CUE
FADER START
1
QUANTIZE
TAP
BALANCE
COLOR
SOUND COLOR FX
NOISE
4
M ST
GRID
BPM
1
0
-26 /
-1
-2
EQ/
-3
ISO
-5
12
6
MID
-2
EQ/
-3
3
B
2
1
0
-26 /
-1
MID
-2
EQ
2
A
PARAMETER
AUTO
TAP
4
2
1
0
-26 /
-1
HI
CH SELECT
MIC
7
9
HI
4
2
1
10
7
9
HI
4
2
OVER
10
7
9
HI
4
2
OVER
10
7
9
HI
4
TRIM
OVER
10
7
0
MIC 2
TRIM
B
MAX
ON / OFF
5 Select [SETUP] on the Serato DJ software’s screen, then
select [TURNTABLES] at the [Audio] tab in the utility settings.
When using DJ players
Here we explain connections for using the Serato DJ software’s [DECK1] and [DECK2] connected to DJ players.
Audio cable
Audio cable
Controlling the Serato DJ software
L R
L R
CH 4
CH 3
PHONO CD/ LINE
POWER
OFF
ON
PHONO CD/ LINE
L
L
RETURN
R
L (MONO)
CH 2
PHONO CD/ LINE
L
L
MIC2
SIGNAL GND
R
MASTER1
R
L
R
MASTER2 REC OUT
L
L
DJ player
R
AC IN
1 GND
MIDI OUT
SIGNAL GND
R
SEND
L (MONO)
R
CH 1
PHONO CD/ LINE
R
2 HOT
3 COLD
DJM-900SRT
R
BOOTH
CH2
TRS
R
L
LINK
DIGITAL
MASTER
OUT
CH4
CH1
IN
DJ player
CH3
USB cable
CONTROL CD
CONTROL CD
To amplifier
To power outlet
Computer
1 Connect the DJ player that will be controlling [DECK1]
to the [CH2] [CD/LINE] terminals, the DJ player that will be
controlling [DECK2] to the [CH3] [CD/LINE] terminals.
4 Select [SETUP] on the Serato DJ software’s screen, then
select [CDJS] at the [Audio] tab in the utility settings.
2 Load the CONTROL CDs in the DJ players.
3 Switch the DJM-900SRT’s input.
Switch the [CH2] and [CH3] input selector switches to [USB].
Input selector switch
CD/ LINE PHONO
DIGITAL
USB
CD/ LINE PHONO
DIGITAL
USB
DECK 1
DECK 2
TRIM
TRIM
POWER
MIC
USB
MASTER
CD/ LINE PHONO
DIGITAL
USB
MIC1
CD/ LINE PHONO
DIGITAL
USB
DECK 3
CD/ LINE PHONO
DIGITAL
USB
DECK 1
CD/ LINE PHONO
DIGITAL
USB
DECK 2
MIDI
START
/ STOP
ON/ OFF
LEVEL
DECK 4-
LFO FORM
WAKE UP
UTILITY
BEAT EFFECTS
0
TRIM
TRIM
OVER
10
MIC 1
LEVEL
1
0
1
0
12
12
6
LOW
- 7 -26 /
12
TALK
OFF ON OVER
-5
- 7 -26 /
6
LOW
-10
-15
dB
DUB
ECHO
SPACE
-5
- 7 -26 /
6
dB
COLOR
GATE/
COMP
- 7 -26 /
dB
6
-3
-5
-7
6
LOW
-10
-10
-15
-24
-26 /
COLOR
dB
6
BEAT
-15
-24
-26 /
X- PAD
-2
ISO
-5
6
-15
-24
6
-1
EQ/
-3
LOW
-10
-15
-26 /
6
MID
-2
ISO
%
ms
0
-26 /
-1
EQ/
-3
LOW
-10
-24
6
MID
-2
ISO
-24
-26 /
COLOR
6
L
dB
R
AUTO
/ TAP
CRUSH
FILTER
CUE
LOW
LINK
HI
LOW
CUE
HI
LOW
CUE
HI
LOW
CUE
HI
CUE
L
R
FLANGER PHASER
FILTER
ROBOT
CUE
TRANS
STEREO
3
4
HEADPHONES
STEREO
MIXING
10
10
10
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
2
1
1
0
CUE
ECHO
REV ROLL
DELAY
FADER START
MONO SPLIT
SLIP ROLL
ROLL
SPIRAL
MONO
2
MELODIC
REVERB
CUE
1
QUANTIZE
TAP
BALANCE
COLOR
SOUND COLOR FX
NOISE
4
M ST
GRID
BPM
1
0
-26 /
-1
EQ/
-3
ISO
-5
12
6
MID
-2
EQ/
-3
3
B
2
1
0
-26 /
-1
MID
-2
EQ
2
A
PARAMETER
AUTO
TAP
4
2
1
0
-26 /
-1
HI
1
MIC
7
9
HI
4
2
CH SELECT
10
7
9
HI
4
2
OVER
10
7
9
HI
4
2
OVER
10
7
9
HI
4
TRIM
OVER
10
7
0
MIC 2
TRIM
OVER
BOOTH MONITOR
MIC
2
CF.A
CF.B
1
MASTER
TIME
0
EQ CURVE
1
0
MIDI LFO
SND/ RTN
4
3
ISOLATOR EQ
0
MASTER
LEVEL / DEPTH
LEVEL
A
THRU B
A
THRU B
A
THRU B
A
THRU B
CH FADER
MIN
0
CROSS FADER
CROSS FADER ASSIGN
MAX
ON / OFF
PHONES
A
B
En
9
When using analog players and DJ players simultaneously
Here we explain connections for using the Serato DJ software’s [DECK1] and
[DECK2] connected to analog players, the Serato DJ software’s [DECK3] and
[DECK4] connected to DJ players.
1 Connect the analog player that will be controlling [DECK1]
to the [CH2] [PHONO] terminals, the analog player that will be
controlling [DECK2] to the [CH3] [PHONO] terminals.
2 Connect the DJ player that will be controlling [DECK3]
to the [CH1] [CD/LINE] terminals, the DJ player that will be
controlling [DECK4] to the [CH4] [CD/LINE] terminals.
3 Switch the DJM-900SRT’s input.
Switch the input selector switches for channels [CH1] – [CH4] to [USB].
Input selector switch
CD/ LINE PHONO
DIGITAL
USB
CD/ LINE PHONO
DIGITAL
USB
DECK 3
CD/ LINE PHONO
DIGITAL
USB
DECK 1
TRIM
CD/ LINE PHONO
DIGITAL
USB
DECK 2
TRIM
DECK 4
TRIM
TRIM
POWER
MIC
USB
MASTER
CD/ LINE PHONO
DIGITAL
USB
MIC1
CD/ LINE PHONO
DIGITAL
USB
DECK 3
CD/ LINE PHONO
DIGITAL
USB
DECK 1
CD/ LINE PHONO
DIGITAL
USB
DECK 2
MIDI
START
/ STOP
ON/ OFF
LEVEL
DECK 4-
LFO FORM
WAKE UP
UTILITY
BEAT EFFECTS
0
TRIM
TRIM
OVER
OVER
10
MIC 1
LEVEL
1
0
1
0
12
12
6
LOW
- 7 -26 /
12
TALK
OFF ON OVER
- 7 -26 /
LOW
-10
DUB
ECHO
SPACE
- 7 -26 /
6
dB
COLOR
GATE/
COMP
dB
6
-5
-7
6
LOW
-10
-10
-15
-24
-26 /
COLOR
dB
6
BEAT
-15
-24
-26 /
X- PAD
-3
ISO
- 7 -26 /
6
-15
-24
6
-1
-2
EQ/
-5
LOW
-10
-15
-26 /
6
MID
-3
ISO
%
ms
0
-26 /
-1
-2
EQ/
-5
LOW
-10
-15
-24
dB
ISO
-5
6
6
MID
-3
-24
-26 /
COLOR
6
L
dB
R
AUTO
/ TAP
CRUSH
FILTER
CUE
LOW
LINK
HI
LOW
CUE
HI
LOW
CUE
HI
LOW
CUE
HI
CUE
L
R
FLANGER PHASER
ROBOT
FILTER
CUE
TRANS
3
STEREO
REV ROLL
DELAY
STEREO
MIXING
10
10
10
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
1
BOOTH MONITOR
MIC
2
CF.A
CF.B
1
MASTER
TIME
0
EQ CURVE
1
0
MIDI LFO
SND/ RTN
4
3
2
1
0
CUE
ECHO
4
HEADPHONES
MONO SPLIT
SLIP ROLL
ROLL
SPIRAL
MONO
2
MELODIC
REVERB
CUE
FADER START
1
QUANTIZE
TAP
BALANCE
COLOR
SOUND COLOR FX
NOISE
4
M ST
GRID
BPM
1
0
-26 /
-1
-2
EQ/
-3
ISO
-5
12
6
MID
-2
EQ/
-3
3
B
2
1
0
-26 /
-1
MID
-2
EQ
2
A
PARAMETER
AUTO
TAP
4
2
1
0
-26 /
-1
HI
CH SELECT
MIC
7
9
HI
4
2
1
10
7
9
HI
4
2
OVER
10
7
9
HI
4
2
OVER
10
7
9
HI
4
TRIM
OVER
10
7
0
MIC 2
TRIM
ISOLATOR EQ
0
MASTER
LEVEL / DEPTH
LEVEL
A
THRU B
A
THRU B
A
THRU B
A
THRU B
CH FADER
MIN
0
CROSS FADER
CROSS FADER ASSIGN
MAX
ON / OFF
PHONES
A
B
4 Select [SETUP] on the Serato DJ software’s screen, then
select [CUSTOM] at the [Audio] tab in the utility settings.
When [CUSTOM] is selected, the DJM-900SRT settings utility is displayed.
10
En
5 Select the [MIXER OUTPUT] tab in the settings utility, then
from the pull-down menu corresponding to the channel
to which the player is connected, select [CH* Control Tone
PHONO] for [USB3/4] and [USB5/6] for using the analog
players, [CH* Control Tone CD/LINE] for [USB1/2] and [USB7/8]
for using the DJ players.
Checking the control signals
1
2
Press the play button on the connected player and play track 1.
For details, see the Serato DJ software manual.
The Serato DJ software manual can be downloaded from the Pioneer DJ support site
below.
See [Software Info] under [DJM-900SRT].
http://pioneerdj.com/support/
1 [crates] panel
2 [Files] panel
Loading tracks
1 From the [crates] panel, click [crates], etc., to open [Library].
Selecting the play mode
The Serato DJ software provides three play modes that can be selected according to
your intended purpose.
[ABS], [REL] and [INT] can be selected on the deck unit.
Here we explain the procedure with the play mode set to [ABS] as an example.
Select [ABS] at the tab on the deck unit.
Controlling the Serato DJ software
Green ring appears at [CALIBRATION DECK].
Check that the innermost ring is close to a true circle.
2 Select a track from [Library], then drag and drop it to
[DECK1] to load it.
Playing tracks
Here we explain how to output the sound of [DECK1] (CH2) as an example.
! Set the volume of the devices (power amplifier, powered speakers, etc.) connected to the [MASTER1] and [MASTER2] terminals to an appropriate level.
Note that loud sound will be output if the volume is set too high.
1 Press the play button on the connected player and play
track 1.
Play a track in the Serato DJ software.
2 Turn the [TRIM] control.
Turn the [TRIM] control to adjust so that the channel level indicator’s orange indicator lights at the peak level.
3 Move the channel fader away from you.
For a description of the respective play modes, see the Serato DJ software manual.
The Serato DJ software manual can be downloaded from the Pioneer DJ support site
below.
See [Software Info] under [DJM-900SRT].
http://pioneerdj.com/support/
4 Turn the [MASTER LEVEL] control to adjust the audio level
of the speakers.
Adjust the sound level output from the [MASTER1] and [MASTER2] terminals to an
appropriate level.
Note
Importing or loading tracks
Importing tracks
Here we explain a typical method of operation for importing tracks.
! There are various ways to import tracks with the Serato DJ software. For details,
see the Serato DJ software manual.
! If you are already using Serato DJ software (Scratch Live, ITCH or Serato DJ
Intro) and have already created track libraries, the track libraries you have previously created can be used as such.
1 Click the [Files] key on the Serato DJ software screen to
open the [Files] panel.
The contents of your computer or the peripheral connected to the computer are
displayed in the [Files] panel.
This unit and the Serato DJ software include a variety of functions enabling individualistic DJ performances. For details on the respective functions, see the operating
instructions and the Serato DJ software manual.
! This unit’s operating instructions can be downloaded from the Pioneer DJ
support site. For details, see “Acquiring the manual” in this unit’s operating
instructions.
! The Serato DJ software manual can be downloaded from the Pioneer DJ support
site below.
See [Software Info] under [DJM-900SRT].
http://pioneerdj.com/support/
Quitting the system
1 Quit [Serato DJ].
When the software is closed, a message for confirming that you want to close it
appears on the computer’s screen. Click [Yes] to close.
2 Click the folder on the [Files] panel containing the tracks
you want to add to the library to select it.
2 Press the [POWER] button on this unit’s rear panel to turn
the power off.
3 On the Serato DJ software screen, drag and drop the
selected folder to the crates panel.
3 Disconnect the USB cable from your computer.
A crate is created and the tracks are added to the library.
— The specifications and design of this product are subject to change without
notice.
© 2013 PIONEER CORPORATION. All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
<DRI1157-A>
En
11