Download Netgear ProSafe JFS524F User's Manual
Transcript
524F ProSafe 10/100 Switch W/100FX 2005 NETGEAR, ProSafe, and Auto Uplink are registered trademarks of NETGEAR, Inc in the United States and other countries. All other trademarks and registered trademarks are the property of their respective owners. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferences in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interferences to radio communications. However, there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. By certified that the NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX has been This digital apparatus (NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX) does not exceed the Class A limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations o f the Canadian Department of Communications. This is to certify that the NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN35 022 Class A (CISPR 22). Cet appareil numérique (NETGEAR Prosafe JFS524F Fast Ethernet Switch W/100FX) respecte les limites de bruits radioélectriques visant les appareils numériques de class A rpescrites dans le Reglement sur le brouillage radioélectrique du mimisére des Communications du Canada. 201-10520-01 The NETGEAR® ProSafe JFS524F 24 Port 10/100 Mbps Switch with 100FX provides you with a low-cost, high-performance network solution and are designed to support power workgroups operating at either 10 megabits per second (Mbps) or 100 Mbps. With the ProSafe JFS524F 24 Port 10/100 Mbps Switch with optional 100FX module (AF711F), improvement is accomplished very easily, with no change to the desktop (the network interface cards or software and the network wiring). As a result, the performance upgrade and the applications it enables are obtained very quickly and at a low cost. ProSafe ProSafe ProSafe JFS524F switch is used as a desktop switch to build a small network that enables users to have 100 Mbps access to a file server. If a full-duplex adapter card is installed in the server or PC, a 200Mbps connection is possible on the port where the server or PC is completed. Model JFS524F Description (Port Number) Solid Valid Link on the port. Blinking Packet transmission or receiving on the port. The port is operating in 10 Mbps mode, if corresponding L/A LED is Solid or Blinking SC Link/Act On Valid Link on the port (Optional) Blinking Packet transmission or receiving on the port IEEE 802.3i 10BASE-T Ethernet IEEE 802.3 100BASE-FX Fast Ethernet IEEE 802.3x Flow Control Compatible with major network software, including Windows, NetWare, and Linux Maximum Optional SC module (AF711F) 6.9W The modularity of ProSafe JFS524F switch provides you with a highly adaptable network. You can not only configure your network for 100FX fiber uplink, but, you also can opt to expand your network gradually and affordably as needed. 328x43.2x169mm 1.6kg/3.5 lbs VCCI Class A/ FCC Class A/ CE/ C-tick/ MIC CUL To install an optional 100FX SC module (AF711F) a. Unscrew and remove the module cover plate. b. Insert the module (AF711F) into the slot, press firmly to seat the module. c. Tighten the module screws. d. Power OFF and Power ON again if power has remained ON throughout the installation of SC module (AF711F). MTBF 256KB 110987.8 hrs (12.7 yrs) Print material spec. material: coated 100lb art paper color: black and white with minimum 300 dpi grayscale images Binding: make two fold dimension: 400(W) x 260(H) mm (before folded) 200(W) x 130(H) mm (after folded) Project source files: illustrator 10 *Page 3 is not part of QIG, please do not print.