Download JVC KD-SH99 User's Manual

CD RECEIVER
KD-SH99
ENGLISH
RECEPTOR CON CD
KD-SH99
ESPAÑOL
RECEPTEUR CD
KD-SH99
FRANÇAIS
Detachable
ATT
ANGLE
EQ
CD
DAB
DISC
FM
PRESET
PRESET
AM
RD
CH
DISC
AUX
SEL
VOLUME
RM-RK100
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
For customer Use:
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
LVT0654-001A
[J]
COVER.KD-SH99[J]f
3
4/3/01, 2:55 PM
ENGLISH
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT FOR LASER PRODUCTS
Precautions:
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock failed or defeated. Avoid direct
exposure to beam.
3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all
servicing to qualified service personnel.
4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches
to prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.
5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified
herein may result in hazardous radiation exposure.
How to reset your unit
CAUTION:
Press the reset button on the front panel using a
ball-point pen or similar tool.
NEVER insert your finger in between the
control panel and the unit, as it may get
caught or hurt. (See page 29.)
Note:
Your preset adjustments – such as preset channels or
sound adjustments – will be erased.
BEFORE USE
*For safety....
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
*Temperature inside the car....
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
2
EN02-04.KD-SH99[J]f
2
4/3/01, 2:55 PM
Thank you for purchasing a JVC product. Please read all instructions carefully before operation,
to ensure your complete understanding and to obtain the best possible performance from the unit.
How to reset your unit ...............................
2
LOCATION OF THE BUTTONS ............
4
Control panel ...........................................
Remote controller ....................................
Preparing the remote controller ................
4
5
6
BASIC OPERATIONS ......................
7
RADIO BASIC OPERATIONS .............
8
Listening to the radio ................................
8
Storing stations in memory .......................
9
Tuning into a preset station ...................... 10
CD OPERATIONS .......................... 11
Playing a CD ............................................
Locating a track or particular portion
on a CD .................................................
Selecting CD playback modes ..................
Playing a CD Text ....................................
Prohibiting disc ejection ............................
11
12
12
13
13
MP3 INTRODUCTION ..................... 14
What is MP3? ..........................................
How are MP3 files recorded and
played back? .........................................
14
14
MP3 OPERATIONS ........................ 16
ENGLISH
CONTENTS
SOUND ADJUSTMENTS .................. 21
Adjusting the sound .................................
Reinforcing the bass sound ......................
Selecting preset sound modes .................
Storing your own sound adjustments .......
21
21
22
23
OTHER MAIN FUNCTIONS ............... 24
Setting the clock ......................................
Changing the general settings (PSM) ......
Assigning names to the sources ..............
Changing the control panel angle .............
Detaching the control panel ......................
24
24
28
29
30
EXTERNAL COMPONENT OPERATIONS .. 31
Playing external components ................... 31
CD CHANGER OPERATIONS ............. 33
Playing CDs ............................................. 33
Selecting CD playback modes .................. 34
ADDITIONAL INFORMATION ............. 35
TROUBLESHOOTING...................... 36
MAINTENANCE ............................ 38
Handling discs .........................................
38
SPECIFICATIONS .......................... 39
Playing an MP3 disc ................................. 16
Locating a file or particular portion
on an MP3 disc ..................................... 17
Selecting MP3 playback modes ............... 20
About the demonstration mode (DEMO MODE)...
When shipped from the factory, “DEMO MODE” is set to “DEMO ON” in this unit.
The following demonstration, introducing the main features equipped with this unit, will appear on the
display automatically if no sound comes in for 3 minutes. (See page 27.)
• MP3
: (Enables you to play MP3 discs.)
• 24bit DAC
: (24 bit digital-analog converter: Gives you a high quality sound after D/A
conversion.)
• HS TUNER
: (High-sensitivity Tuner: Enables a fine reception of stations.)
• EQUALIZER : (Enables you to fine-adjust the sound to match your preference.)
• SUB WOOFER: (Enables you to connect a subwoofer and to adjust its output level.)
CAUTION on Volume Setting
CDs produce very little noise compared with other sources. If the volume level is adjusted for the tuner, for
example, the speakers may be damaged by the sudden increase in the output level. Therefore, lower the
volume before playing a disc and adjust it as required during playback.
3
EN02-04.KD-SH99[J]f
3
4/3/01, 2:55 PM
ENGLISH
LOCATION OF THE BUTTONS
Control panel
1
2
3
y
4
5
6
8
7
r
t
0 (eject) button
Control dial
SEL (select) button
EQ (equalization) button
S.BASS (S) (super bass) button
DISP (D) (display) button
BAND (B) button
MODE (M) button
4/¢
buttons
• Also function as SSM buttons when pressed
together.
p
ATT (angle/attenuator) button
1
2
3
4
5
6
7
8
9
p
9
e
q
w
q MP3 INPUT jack
w
(control panel release) button
e Remote sensor
r Number buttons
• MO (monaural) button
• LO (local) button
• INT (intro scan) button
• RPT (repeat) button
• RND (random) button
• DVD/Video component operation buttons
t SOURCE
(standby/on) button
y Reset button
How to use MODE (M):
If you press MODE (M), this button functions as the Mode button and the unit goes into functions
mode whereby the number buttons and 4/¢ buttons work as different function buttons.
Normally
Equalizing
pattern indicator
During
functions mode
Time countdown
indicator
To use these buttons as number buttons and 4 /¢ buttons again after pressing MODE (M),
wait for 5 seconds without pressing any number button until the functions mode is cleared.
• Pressing MODE (M) again also clears the functions mode.
4
EN02-04.KD-SH99[J]f
4
4/3/01, 2:55 PM
1
3
ATT
ANGLE
EQ
5
6
CD
DAB
4
DISC
ENGLISH
4 Selects the sound modes.
Each time you press the button, sound modes
change.
Remote controller
5 • Searches for stations while listening to the
radio.
• Fast-forwards or reverses the track/file if
pressed and held while listening to any disc.
• Skips to the beginning of the next track/file or
goes back to the beginning of the current (or
previous) track/file if pressed briefly while
listening to any disc. (See pages 12 and 17.)
FM
2
PRESET
PRESET
AM
RD
CH
8
9
DISC
AUX
7
SEL
VOLUME
p
RM-RK100
6 • Changes the preset channel number while
listening to the radio.
Each time you press the button, the preset
channel number changes, and the selected
station is tuned into.
• Skips to the first file of the next directory or
the first file of the previous directory if
pressed and held while listening to an MP3
disc. (See page 18.)
• Skips to the first file of the next directory or
the first file of the previous directory of the
same hierarchy level if pressed briefly while
listening to an MP3 disc. (See page 19.)
1 • Turns on the unit if pressed when the unit
is turned off.
• Turns off the unit if pressed and held until
“SEE YOU” appears on the display.
• Drops the volume level if pressed briefly,
and “ATT” flashes on the display.
Press again to resume the volume.
7 • Changes the disc number while listening to
the CD changer.
Each time you press the button, the disc
number changes, and the selected disc
starts playing.
• Skips to the first file of a directory of an upper
hierarchy level or a lower hierarchy level if
pressed briefly while listening to an MP3 disc.
(See page 19.)
2 • CD :
• FM :
8 Skips to the root directory while listening to an
MP3 disc. (See page 19.)
Selects CD player.
Selects FM tuner.
Each time you press the button, FM
band (FM1, FM2 and FM3) changes.
• Does not function as the DAB button.
• AM : Selects AM tuner.
• CH : Selects CD changer.*
• AUX : Selects the external components.
Each time you press the button,
“AUX INPUT” and “LINE INPUT” are
alternately selected.
3 Changes the angle of the control panel to
four positions.
9**
Selects the sound adjustment items.
Each time you press the button, the items
change.
p**
• Changes the volume.
• Adjusts the sound mode (after SEL is
pressed).
* Without connecting the CD changer, you cannot
select it as the source to play.
** These buttons do not function for the preferred
setting mode adjustment.
5
EN05-06.KD-SH99[J]f
5
4/3/01, 2:56 PM
ENGLISH
Preparing the remote controller
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the main unit. Make sure there is no
obstacle in between.
2. Place the battery.
Slide the battery into the holder with the + side
facing upwards so that the battery is fixed in
the holder.
Lithium coin battery
(product number:
CR2025)
3. Return the battery holder.
Insert again the battery holder pushing it until
you hear a clicking sound.
Remote sensor
(back side)
• Do not expose the remote sensor to strong
light (direct sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of the
remote controller decreases, replace the battery.
1. Remove the battery holder.
1) Push out the battery holder in the direction
indicated by the arrow using a ball-point
pen or a similar tool.
2) Remove the battery holder.
(back side)
1)
2)
WARNING:
• Store the battery in a place where children cannot
reach.
If a child accidentally swallows the battery,
consult a doctor immediately.
• Do not recharge, short, disassemble, heat or
dispose the battery in a fire.
Doing any of these things may cause the battery to
give off heat, crack or start a fire.
• Do not leave the battery with other metallic
materials.
Doing this may cause the battery to give off heat,
crack or start a fire.
• When throwing away or saving the battery, wrap it
in tape and insulate; otherwise, the battery may
start to give off heat, crack or start a fire.
• Do not poke the battery with tweezers or similar
tools.
Doing this may cause the battery to give off heat,
crack or start a fire.
6
EN05-06.KD-SH99[J]f
6
4/3/01, 2:56 PM
ENGLISH
BASIC OPERATIONS
Note:
When you use this unit for
the first time, set the built-in
clock correctly, see page 24.
2
1
1
Turn on the power and select the
source.
2
To increase the volume.
When you press the button
for the first time, the power
comes on. Then each time
you press the button, the
source changes as follows:
FM TUNER
or
AM TUNER
CD PLAY *
AUX INPUT
Adjust the volume.
To decrease the volume.
CD CHANGER **
Volume level appears.
LINE INPUT
Volume level indicator
* If a disc is not in the loading slot, you cannot
select CD as the source to play.
** Without connecting the CD changer, you
cannot select it as the source to play.
To operate the tuner (FM or AM),
see pages 8 – 10.
To play a CD,
see pages 11 – 13.
To play an MP3 disc,
see pages 16 – 20.
To operate external components
(AUX INPUT and LINE INPUT),
see pages 31 – 32.
To operate the CD changer,
see pages 33 – 34.
Note:
After adjusting the volume, you can push in the
control dial to avoid unintended operations.
To use it again, push the control dial again to
make it come out.
3
Adjust the sound as you want.
(See page 21.)
To drop the volume in a moment
Press and hold
/ATT while listening to any
source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press and
hold the button again.
• If you turn the control dial clockwise, you can
also restore the sound.
To turn off the power
Press and hold SOURCE
appears on the display.
until “SEE YOU”
7
EN07-07.KD-SH99[J]f
7
4/3/01, 2:56 PM
ENGLISH
RADIO BASIC OPERATIONS
Listening to the radio
You can use either automatic searching or
manual searching to tune into a particular station.
Searching a station automatically:
Auto search
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM.
Each time you press the
button, the band changes
as follows:
FM 1
FM 2
FM 3
To stop searching before a station is received,
press the same button you have pressed for
searching.
To tune into FM stations only with strong signals
1 Press MODE (M) to enter the functions mode
while listening to an FM broadcast.
2 Press LO (local) while still in the functions
mode, so that the LOCAL indicator lights up on
the display.
This function works only while searching FM
stations, including SSM preset.
Each time you press the button, the LOCAL
indicator lights up and goes off alternately.
Searching a station manually:
Manual search
1
Select the band (FM1 – 3, AM).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM.
Each time you press the
button, the band
changes as follows:
AM
Selected band appears.
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
2
Start searching a station.
Press ¢
to search
stations of higher
frequencies.
Press
4 to search
stations of lower
frequencies.
8
FM 1
FM 2
8
AM
Note:
This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.
When a station is received, searching stops.
EN08-10.KD-SH99[J]f
FM 3
4/3/01, 2:56 PM
Press and hold ¢
or
4 until
“M” (manual) starts flashing on the
display.
Storing stations in memory
ENGLISH
2
You can use one of the following two methods to
store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strongstation Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
3
Tune into a station you want while “M”
is flashing.
You can preset 6 local FM stations in each FM
band (FM1, FM2 and FM3).
1
Press ¢
to tune
into stations of higher
frequencies.
Select the FM band (FM1 – 3) you want
to store FM stations into.
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select the FM band.
Each time you press the
button, the band changes
as follows:
Press
4 to tune
into stations of lower
frequencies.
• If you release your finger from the button,
the manual mode will automatically turn off
after 5 seconds.
• If you hold down the button, the frequency
keeps changing until you release the
button.
When an FM stereo broadcast is hard to
receive:
1 Press MODE (M) to enter the
functions mode while listening to
an FM stereo broadcast.
2 Press MO (monaural) while still in
the functions mode, so that the
MO indicator lights up on the
display.
• Each time you press the button,
the MO and ST (stereo) indicators
light up alternately.
Lights up when receiving
an FM broadcast in stereo.
The MO indicator lights
up.
FM 1
2
FM 2
FM 3
AM
Press and hold both buttons for more
than 2 seconds.
“SSM” appears, then
disappears when automatic
preset is over.
Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2 or FM3).
These stations are preset in the number buttons
— No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned into.
When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved (the ST indicator
goes off).
9
EN08-10.KD-SH99[J]f
9
4/3/01, 2:56 PM
Tuning into a preset station
ENGLISH
Manual preset
You can preset up to 6 stations in each band
(FM1, FM2, FM3 and AM) manually.
Ex.: Storing an FM station of 88.3 MHz into the
preset number 1 of the FM1 band
You can easily tune into a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on page 9.
1
1
Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM or AM.
Each time you press the
button, the band changes
as follows:
1 Press SOURCE
repeatedly to select the
tuner as the source.
2 If necessary, press
BAND (B) repeatedly to
select FM 1.
Each time you press the
button, the band
changes as follows:
FM 1
2
FM 2
FM 3
Select the band (FM1 – 3, AM).
FM 1
FM 2
FM 3
AM
AM
2
Tune into a station of 88.3 MHz.
Select the number (1 – 6) for the preset
station you want.
Press ¢
to tune
into stations of higher
frequencies.
4 to tune
Press
into stations of lower
frequencies.
3
Press and hold the number button (in
this example, 1) for more than 2
seconds.
“P1” flashes for a while.
4
10
Repeat the above procedure to store
other stations into other preset
numbers.
Notes:
• A previously preset station is erased when a new
station is stored in the same preset number.
• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example, during
battery replacement). If this occurs, preset the stations
again.
EN08-10.KD-SH99[J]f
10
If the sound quality decreases and the
stereo effect is lost while listening to
an FM station...
In some areas, adjacent stations may interfere
with each other. If this interference occurs, this
unit can automatically reduce this interference
noise (the initial setting when shipped from the
factory). However, in this case, the sound
quality will be degraded and the stereo effect
will be also lost.
If you do not want to degrade the sound quality
and to lose the stereo effect, rather than to
eliminate the interference noise, see “To
change the FM tuner selectivity – IF FILTER”
on page 27.
When using this until in an area other than
North or South America:
You need to change the AM/FM channel
intervals. See “To change the AM/FM channel
intervals – AREA” on pages 26 and 27.
4/3/01, 2:56 PM
ENGLISH
CD OPERATIONS
When playing an MP3 disc, refer also to
“MP3 OPERATIONS” on pages 16 to 20.
Playing a CD
1
Open the loading slot.
The control panel moves down,
and the loading slot appears.
Note:
When an external component is connected to the MP3
INPUT jack, be careful of handling a CD.
2
Insert a disc into the loading slot.
The unit draws the
disc, the control panel
goes back to its
previous position (see
page 29), and CD play
starts automatically.
• All the tracks on the
disc will be played
repeatedly until you
stop playback—All
Track Repeat Play.
Note:
Do not insert any 8 cm disc into the loading slot as it
will get stuck inside.
The display changes to show the following:
Notes:
• When a disc is in the loading slot, selecting “CD”
as the source by pressing SOURCE
starts CD
play.
• When a disc is inserted upside down, the disc
automatically ejects.
• When you play a CD Text, the disc title and
performer appear on the display. Then the current
track title appears on the display, followed by the
track number and elapsed playing time. See also
“Playing a CD Text” (page 13) and “To select the
scroll mode – SCROLL” (page 26).
If a CD Text includes too much text information, some
may not appear on the display.
• If you change the source, CD play also stops (without
ejecting the disc).
To stop play and eject the disc
Press 0.
CD play stops, the control panel moves down, and
the disc automatically ejects from the loading slot.
To return the control panel to its previous
position, press 0 again.
• If you keep the loading slot open for one minute
(or 30 seconds when you have ejected a disc with
the ignition key turned to “OFF”), a beep sounds
and the control panel returns to its previous
position.
Be careful not to get the disc or your finger
caught in between the control panel and the unit.
Note:
If the ejected disc is not removed within 15 seconds, the
disc is automatically inserted again into the loading slot
to protect it from dust. (CD play will not start this time.)
Total track
number of the
inserted disc
Current track
EN11-13.KD-SH99[J]f
Total playing time of
the inserted disc
Elapsed playing time
11
11
4/3/01, 2:57 PM
ENGLISH
Locating a track or particular
portion on a CD
To fast-forward or reverse the track
Press and hold ¢
while playing a disc, to
fast-forward the track.
Press and hold
4
while playing a disc, to
reverse the track.
To go to the next track or the previous tracks
Press ¢
briefly while
playing a disc, to go ahead
to the beginning of the next
track. Each time you press
the button consecutively, the
beginning of the next track is
located and played back.
Press
4 briefly while
playing a disc, to go back to
the beginning of the current
track. Each time you press
the button consecutively, the
beginning of the previous
tracks is located and played
back.
To go to a particular track directly
Press the number button corresponding to the track
number to start its playback.
Selecting CD playback modes
To play back tracks at random (Random Play)
1 Press MODE (M) while
playing a disc. The unit enters
the functions mode.
2 Press RND (random) while still
in the functions mode, so that
the RND indicator lights up on
the display.
Then, each time you press
RND, the random play mode
turns on and off alternately.
When the random mode is turned on, the RND
indicator lights up on the display and a track
randomly selected starts playing.
To play back the current track repeatedly
(One Track Repeat Play)
1 Press MODE (M) while
playing a disc. The unit enters
the functions mode.
2 Press RPT (repeat) while still
in the functions mode, so that
the RPT indicator lights up on
the display.
Then, each time you press
RPT, the One Track Repeat
Play mode turns on and off
alternately.
• When One Track Repeat
Play is turned off, All Track
Repeat Play is activated.
• To select a track number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a track number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.
Track number
Elapsed playing time
12
EN11-13.KD-SH99[J]f
12
4/3/01, 2:57 PM
You can play back the first 15 seconds of each
track sequentially.
1 Press MODE (M) while
playing a disc. The unit enters
the functions mode.
2 Press INT (intro scan) while still
in the functions mode, so that
the “INT” appears on the display.
Then, each time you press INT,
the intro scan play mode turns
on and off alternately.
4
Track number of the
currently playing track
Playing a CD Text
In a CD Text, some information about the disc (its
disc title, performer and track title) is recorded.
You can show these disc information on the
display.
1
Select text display mode while
playing a CD Text.
Prohibiting disc ejection
You can prohibit disc ejection and can lock a disc
in the loading slot.
ENGLISH
To play back only intros (Intro scan)
While pressing SEL (select),
press and hold 0 for more than 2
seconds.
“NO EJECT” flashes on the
display for about 5 seconds, and
the disc is locked and cannot be
ejected.
Note:
If you press 0 while disc ejection is prohibited, the
control panel moves down, but the disc cannot be
ejected.
To return the display panel to its previous position,
press 0.
To cancel the prohibition and unlock the disc,
press and hold 0 for more than 2 seconds again,
while pressing SEL.
“EJECT OK” flashes on the display for about 5
seconds, and the disc is unlocked.
Each time you press the button,
the display changes as follows:
Disc Title / Performer
Track Title
Current track no.
and Elapsed playing time
Notes:
• The display shows up to 10 characters at one time
and scrolls if there are more than 10 characters.
See also “To select the scroll mode – SCROLL” on
page 26.
• When you press DISP (D) while playing a
conventional CD, “NO NAME” appears for the disc
title/performer and the track title.
13
EN11-13.KD-SH99[J]f
13
4/3/01, 2:57 PM
ENGLISH
MP3 INTRODUCTION
What is MP3?
MP3 is an abbreviation of Motion Picture Experts
Group (or MPEG) Audio Layer 3. MP3 is simply a
file format with a data compression ratio of 1:10
(128 Kbps*). That means, by using MP3 format,
one CD-R or CD-RW can contain 10 times as
much data volume as a regular CD can.
* Bit rate is the average number of bits that one second of
audio data will consume. The unit used is Kbps (1000 bits/
second). To get a better audio quality, choose a higher bit
rate. The most popular bit rate for encoding is 128 Kbps.
This unit is incorporated with an MP3 decoder.
You can play back MP3 files (tracks) recorded on
CD-Rs, CD-RWs, and CD-ROMs.
Compatible with ID3v1
Extra information data such as album title, performer
name, song title, recording year, music genre and a
brief comment can be stored within an MP3 file.
This unit can show ID3v1 tags (album name,
performer name and song title) on the display.
• Some characters cannot be shown correctly.
• This unit is not compatible with ID3v2.
Other Main Features in this unit:
• Maximum number of hierarchy levels: 8
• Maximum number of directories/files: 255
(Total)
• Available characters: A–Z, 0–9, _ (underscore)
• Maximum number of characters for file name
(ISO 9660 Level 1): 12 (inclusive of
separation mark—“.” and
extension code—“mp3”)
(ISO 9660 Level 2): 31 (inclusive of
separation mark—“.” and
extension code—“mp3”)
• Maximum number of characters for directory
name: 31
How are MP3 files recorded
and played back?
MP3 “files (tracks)” can be recorded in
“directories (folders)”—in PC terminology.
During recording, the files and directories can be
arranged in a way similar to arranging files and
directories/folders of computer data.
“Root” is similar to the root of a tree. Every file
and directory can be linked to and be accessed
from the root.
In compliance with ISO 9660, the maximum
allowable depth of nested directories—so-called
“hierarchy”—is eight (inclusive of the root
directory).
Playback order, file search order, and directory
search order of the MP3 files recorded on a disc
are determined by the writing (or encoding)
application; therefore, playback order may be
different from the one you have intended while
recording the directories and the files.
The illustration on the next page shows an
example of how MP3 files are recorded on a
CD-R or CD-RW, how they are played back, and
how they are searched on this unit.
Notes:
• The unit can read a CD-ROM containing MP3
files. However, if non-MP3 files are recorded
together with MP3 files, this unit will take a longer
time to scan the disc. It may also cause the unit to
malfunction.
• The unit cannot read or play an MP3 file without
the extension code—mp3.
• The unit is not compatible with Playlist**.
** A playlist is a simple text file, used on a PC, which enables
users to make their own playback order without physically
rearranging the files.
Precautions when recording MP3 files
on a CD-R or CD-RW
This unit can only read MP3 files that are recorded
in the format that is compliant with ISO 9660 Level 1
or Level 2.
14
EN14-20.KD-SH99[J]f
14
4/3/01, 2:57 PM
1
2
4
8
1 2 3 4
Level 4
Level 3
Level 2
ROOT
3
5
10
5 6
Level 5
Hierarchy
ENGLISH
Level 1
MP3 directory/file configuration
20
6
7
8
9
12
1
21
7
22
13
Level 6
ROOT
9
11
14
15 16
17
23 24
18 19
Notes:
• In compliance with ISO 9660, the maximum number of hierarchy
levels is eight, including the root directory.
• When a multi-session disc is loaded, you can only play back the
contents of the last session.
: Root
: Directories
: MP3 files
MP3 playback/search order (page 17)
• The numbers in circles next to the MP3 files ( ) indicate the playback order and search order of
the MP3 files. Normally this unit plays back MP3 files in the recorded order.
• The numbers inside the directories indicate the playback order and search order of the directories
on an MP3 disc. Normally this unit plays back MP3 files in the directories in the recorded order.
Movement between the directories (page 19)
You can move to another directory on the same hierarchy level (e.g. from Directory 3, you can go to
Directory 5 or 9) or on a different hierarchy level (e.g. from Directory 5, you can go to Directory 4 or 6).
15
EN14-20.KD-SH99[J]f
15
4/3/01, 2:57 PM
ENGLISH
MP3 OPERATIONS
Refer also to “CD OPERATIONS” on pages 11 to
13.
Playing an MP3 disc
1
Open the loading slot.
The control panel moves down,
and the loading slot appears.
2
Insert an MP3 disc into the loading slot.
The unit draws the
disc, the control panel
goes back to its
previous position (see
page 29), and
playback starts
automatically.
Playback starts automatically from the first file
of the first directory once file check is
completed.
Then, the display changes to show the
following:
• When “TAG ON” is selected (initial
setting: see page 27)
Album name/performer name (directory
name)* = Track title (file name)* =
Elapsed playing time
* If an MP3 file does not have ID3 tags,
directory name and file name appear.
• When “TAG OFF” is selected
Directory name and file name appear.
Notes:
• All the files on the disc will be played repeatedly
until you stop playback—All File Repeat Play.
• MP3 discs require a longer readout time**.
(It differs due to the complexity of the directory/file
configuration.)
** Readout time is the time taken by the unit to scan or
check the disc for files and file information.
Ex.: When the disc contains 13 directories and
125 MP3 files.
16
EN14-20.KD-SH99[J]f
16
4/3/01, 2:57 PM
While playing back an MP3 file, you
can change the file information
shown on the display.
Each time you press DISP (D), the
display changes to show the
following:
• When “TAG ON” is selected (initial
setting: see page 27)
Album name/
Track title
Performer name
(File name)
(Directory name)
Elasped playing time
* If an MP3 file does not have ID3 tags,
directory name and file name appear.
• When “TAG OFF” is selected
File name
Directory name
Elasped playing time
Note:
• The display shows up to 10 characters at one time
and scrolls if there are more than 10 characters.
See also “To select the scroll mode – SCROLL” on
page 26.
To stop play and eject the disc
Press 0.
Playback stops, the control panel moves down
and the disc automatically ejects from the loading
slot.
Locating a file or particular
portion on an MP3 disc
To fast-forward or reverse the file
ENGLISH
To change the display information
Press and hold ¢
while playing an MP3 disc,
to fast-forward the file.
Press and hold
4
while playing an MP3 disc,
to reverse the file.
To skip to the next file or the previous files
Press ¢
briefly while
playing, to skip ahead to the
beginning of the next file.
Each time you press the
button consecutively, the
beginning of the next file is
located and played back.
(See “MP3 playback/search
order” on page 15.)
Press
4 briefly, while
playing, to skip back to the
beginning of the current file.
Each time you press the
button consecutively, the
beginning of the previous
files is located and played
back. (See “MP3 playback/
search order” on page 15.)
17
EN14-20.KD-SH99[J]f
17
4/3/01, 2:57 PM
ENGLISH
To go to a particular directory directly
IMPORTANT:
To directly select the directories using the
number button(s), it is required that directories
are assigned 2 digit numbers at the beginning of
their directory names. (This can only be done
during the recording of CD-Rs or CD-RWs.)
Ex.: If directory name is “01 ABC”
press 1 to go to directory 01 ABC
If directory name is “1 ABC”
pressing 1 does not work
If directory name is “12 ABC”
press and hold 6 (12) to go to
directory 12 ABC
Press the number button corresponding to the
directory number to start playing the first file in
the selected directory.
To skip to the next directory—either on
the same hierarchy level or on a different
hierarchy level
On the control panel:
1 Press MODE (M) while
playing an MP3 disc. The unit
enters the functions mode.
briefly while
2 Press ¢
still in the functions mode.
Each time you repeat steps
1 and 2, the next directory is
located (and the first file in
the directory starts playing, if
recorded).
(See “MP3 playback/search
order” on page 15.)
On the remote controller:
PRESET
• To select a directory number from 01 – 06:
Press 1 (7) – 6 (12) briefly.
• To select a directory number from 07 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.
Notes:
• If “MP3” flashes on the display after you have
selected a directory, it means that the directory does
not contain any MP3 files.
• You cannot directly select a directory with a number
greater than 12.
Each time you press and hold
the button consecutively, the
next directory is located (and the
first file in the directory starts
playing, if recorded).
(See “MP3 playback/search
order” on page 15.)
To skip to the previous directory—either
on the same hierarchy level or on a
different hierarchy level
On the control panel:
1 Press MODE (M) while
playing an MP3 disc. The unit
enters the functions mode.
2 Press
4 briefly while still
in the functions mode.
Each time you repeat steps
1 and 2, the previous
directory is located (and the
first file in the directory starts
playing, if recorded).
(See “MP3 playback/search
order” on page 15.)
To select a particular file in a directory, press
¢
or
4 after selecting the directory.
On the remote controller:
PRESET
18
EN14-20.KD-SH99[J]f
18
Each time you press and hold
the button consecutively, the
previous directory is located
(and the first file in the directory
starts playing, if recorded).
(See “MP3 playback/search
order” on page 15.)
4/3/01, 2:57 PM
To skip to the directories on the lower
hierarchy levels
On the remote controller:
On the remote controller:
Each time you press the button
consecutively, the next directory
on the same hierarchy level is
located (and the first file in the
directory starts playing, if
recorded).
PRESET
Ex.1: While playing an MP3 file in Directory 4
(see the illustration on page 15)
Each time you press the button
consecutively, a directory on the
lower hierarchy level is located
(and the first file in the directory
starts playing, if recorded).
DISC
Ex.1: While playing an MP3 file in Directory 1
(see the illustration on page 15)
1
4
8
2
3
On the remote controller:
Ex.1: While playing an MP3 file in Directory 4
(see the illustration on page 15)
2
8
4
Ex.2: While playing an MP3 file in Directory 5
(see the illustration on page 15)
5
3
6
To skip to the directories on the upper
hierarchy levels
On the remote controller:
Each time you press the button
consecutively, a directory on the
upper hierarchy level is located
(and the first file in the directory
starts playing, if recorded).
DISC
Each time you press the button
consecutively, the previous
directory on the same hierarchy
level is located (and the first file
in the directory starts playing, if
recorded).
4
5
5
To skip to the previous directory on the same
hierarchy level
PRESET
3
Ex.2: While playing an MP3 file in Directory 4
(see the illustration on page 15)
4
9
2
4
Ex.2: While playing an MP3 file in Directory 5
(see the illustration on page 15)
5
ENGLISH
To skip to the next directory on the same
hierarchy level
9
5
Note:
If there is no MP3 file in a directory that you have
skipped to, its directory name appears on the display
with “MP3” flashing. If this happens, the unit pauses
automatically.
Ex.1: While playing an MP3 file in Directory 3
(see the illustration on page 15)
3
2
1
ROOT
Ex.2: While playing an MP3 file in Directory 5
(see the illustration on page 15)
5
4
1
ROOT
• If you reach the root, playback will not begin.
To go back to the root directly, press R•D on
the remote controller. You can go back to the root
from any directory.
• If files are recorded on the first hierarchy level
without putting them into a directory, this unit
starts playing the files.
19
EN14-20.KD-SH99[J]f
19
4/3/01, 2:57 PM
ENGLISH
Selecting MP3 playback modes
To play back files at random (Random Play)
1 Press MODE (M) while
playing an MP3 disc. The unit
enters the functions mode.
2 Press RND (random) while
still in the functions mode, so
that the RND indicator lights
up on the display.
Then, each time you press
RND, the random play mode
turns on and off alternately.
When the random mode is turned on, the RND
indicator lights up on the display and a file
randomly selected from all the files on the disc
starts playing.
To play back only intros (Intro scan)
You can play back the first 15 seconds of each file
sequentially.
1 Press MODE (M) while
playing an MP3 disc. The unit
enters the functions mode.
2 Press INT (intro scan) while still
in the functions mode, so that
“INT” appears on the display.
Then, each time you press INT,
4
the intro scan play mode turns
on and off alternately.
File number of the
currently playing file
To play back files repeatedly (Repeat Play)
1 Press MODE (M) while
playing an MP3 disc. The unit
enters the functions mode.
2 Press RPT (repeat) while still
in the functions mode, so that
the RPT indicator lights up on
the display.
Then, each time you press
RPT, the repeat play mode
changes as follows:
RPT 1
RPT 2
Canceled
Ex.: When “RPT 1” is selected.
Mode
RPT
Indicator
Plays repeatedly
RPT 1
Lights
RPT 2
Flashes
The current file (or
specified file).
All files of the current
directory (or specified
directory).
20
EN14-20.KD-SH99[J]f
20
4/3/01, 2:58 PM
Adjusting the sound
Reinforcing the bass sound
You can adjust the sound characteristics to your
preference.
The richness and fullness of the bass sound is
clearly maintained regardless of how low you set
the volume – Super Bass.
• You can also adjust the level of Super Bass.
1
Select the item you want to adjust.
Each time you press the button,
the adjustable items change as
follows:
FAD*
(Balance)
VOL
WOOFER**
(Volume)
(Subwoofer)
To do:
Range
FAD*
Adjust the front
and rear speaker
balance.
R06 (Rear only)
|
F06 (Front only)
BAL
Adjust the left
and right speaker
balance.
L06 (Left only)
|
R06 (Right only)
WOOFER**
Adjust the
subwoofer output
level.
00 (min.)
|
12 (max.)
VOL
Adjust the volume.
00 (min.)
|
50 (max.)
* If you are using a two-speaker system, set the fader
level to “00.”
** This takes effect only when a subwoofer is
connected.
2
Press S.BASS.
“S.BASS” appears on the
display.
BAL
(Fader)
Indication
1
ENGLISH
SOUND ADJUSTMENTS
2
Adjust Super Bass level from
“S. BASS 00” (min.) to “S. BASS 08”
(max.).
To increase the level.
To decrease the level.
Bass level indicator changes
according to the adjusted level.
Adjust the level.
To increase the level.
To decrease the level.
Note:
Normally, the control dial works as the volume
control. So you do not have to select “VOL” to adjust
the volume level.
21
EN21-23.KD-SH99[J]f
21
4/3/01, 2:58 PM
ENGLISH
Selecting preset sound modes
You can select a preset sound mode suitable to
the music genre.
1
Press EQ.
The last selected sound mode
is recalled, and it is applied to
the current source.
The EQ indicator lights up.
Ex.: When you have selected “FLAT” previously
2
Select the sound mode you want.
As you turn the control
dial, the sound modes
change as follows:
Notes:
• You can adjust each sound mode to your preference,
and store it in memory.
If you want to adjust and store your original sound
mode, see “Storing your own sound adjustments”
on page 23.
• To adjust the bass reinforcement level temporarily,
see page 21.
To store a sound mode separately for
each playback source (EQ Link)
Once you select a sound mode, it is stored in
memory. It will be recalled every time you select
the same source.
A sound mode can be stored for each of the
following sources — FM1, FM2, FM3, AM, CD
and external components.
• See also “Changing the general settings (PSM)”
on page 24.
1 Press and hold SEL (select) for more than 2
FLAT O Hard Rock O R & B*O POP O
JAZZ O DanceMusic O Country O Reggae O
Classic O USER 1 O USER 2 O USER 3 O
(back to the beginning)
seconds so that one of the PSM items appears
on the display.
2 Press ¢
or
4 to select “EQ LINK”
(Equalization Link).
3 Turn the control dial clockwise to select “LINK
ON.”
4 Press SEL (select) to finish the setting.
To cancel EQ Link, repeat the same procedure
and select “LINK OFF” by turning the control dial
counterclockwise in step 3.
* Rhythm and Blues
EQ level changes as you select the sound mode.
Ex.: When you select “POP”
To cancel the sound mode, select “FLAT” in
step 2.
• When “EQ LINK” is set to “LINK ON”
The selected sound mode can be stored in
memory for the current source.
Each time you change to the same source, the
same sound mode is also recalled, and shown
after the source name.
• When “EQ LINK” is set to “LINK OFF”
The selected sound mode effect applies to all
the sources selected.
22
EN21-23.KD-SH99[J]f
22
4/3/01, 2:58 PM
3
Adjust the selected sound element.
• Refer to the table below for adjusting the
selected sound element.
You can adjust the sound modes to your preference
and store your own adjustments in memory
(USER 1, USER 2 and USER 3).
• There is a time limit in doing the following
procedure. If the setting is canceled before
you finish, start from step 1 again.
1
4
Press EQ.
The last selected sound mode
is recalled, and is applied to
the current source.
5
ENGLISH
Storing your own sound
adjustments
Repeat steps 2 and 3 to adjust the
other sound elements.
Select one of the user sound modes
(USER 1, USER 2, USER 3).
Ex.: When you have selected “POP” previously
2
Press SEL (select) to select sound
elements to adjust.
Each time you press the
button, the sound elements
change as follows:
LOW FREQ.* = LOW WIDTH = LOW LEVEL =
MID FREQ.* = MID WIDTH = MID LEVEL =
HIGH FREQ.* = HIGH LEVEL =
(back to the beginning)
FREQ. (LOW, MID, HIGH):
Select the center frequency to adjust.
WIDTH (LOW, MID):
Select the band width level (Q).
LEVEL (LOW, MID, HIGH):
Adjust the enhancement level.
* By pressing ¢
or
4, you
can directly move as follows:
LOW FREQ.
MID FREQ.
Ex.: When you select “USER 2”
6
Press EQ to store the adjustments.
To reset to the factory settings
Repeat the same procedure and reassign the
preset values listed in the table on page 35.
Indication
LOW
Preset values
MID
HIGH
FREQ.
50 Hz
80 Hz
120 Hz
700 Hz
1 kHz
2 kHz
WIDTH
1 (min.)
|
4 (max.)
1 (min.)
|
2 (max.)
LEVEL
–06 (min.) –06 (min.) –06 (min.)
|
|
|
+06 (max.) +06 (max.) +06 (max.)
HIGH FREQ.
8 kHz
12 kHz
23
EN21-23.KD-SH99[J]f
23
4/3/01, 2:58 PM
ENGLISH
OTHER MAIN FUNCTIONS
Setting the clock
1
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 25.)
Changing the general settings
(PSM)
You can change the items listed on the next page
by using the PSM (Preferred Setting Mode)
control.
Basic Procedure
2
1
Set the hour.
1 Select “CLOCK HOUR” if not shown on
the display.
2 Adjust the hour.
1
2
2
3
Press and hold SEL (select) for more
than 2 seconds so that one of the PSM
items appears on the display.
(See page 25.)
Select a PSM item you want to adjust.
(See page 25.)
Set the minute.
1 Select “CLOCK MIN.”
2 Adjust the minute.
1
4
2
Press SEL (select) to finish the setting.
3
4
5
Adjust the PSM item selected.
Repeat steps 2 and 3 to adjust the
other PSM items if necessary.
Press SEL (select) to finish the setting.
To check the current clock time while the unit
is turned off, press DISP (D) (display).
The power turns on, the clock time is shown for 5
seconds, then the power turns off.
24
EN24-30.KD-SH99[J]f
24
4/3/01, 2:58 PM
1
2
3
Set.
Hold.
Select.
Counterclockwise
Factory-preset
settings
See
page
1:00
24
LINK OFF
22
CLOCK ON
26
LEVEL+EQ
26
AUTO
26
Clockwise
CLOCK HOUR
Hour adjustment
Back
Advance
CLOCK MIN
Minute adjustment
Back
Advance
EQ LINK
Sound control memory
linkage
LINK OFF
LINK ON
CLOCK DISP
Clock display
LEVEL/EQ
Equalizer/Level indicator
DIMMER
Dimmer mode
BEEP SW
Key-touch tone
BEEP OFF
BEEP ON
BEEP ON
26
P.AMP SW
Power amplifier switch
P.AMP OFF
P.AMP ON
P.AMP ON
26
CONTRAST
Display contrast
CONTRAST 1 – CONTRAST 10
CONTRAST 5
26
SCROLL
Scroll mode
ONCE
26
FREQ MID
26
AREA US
26
CLOCK OFF
CLOCK ON
EQ ONLY
LEVEL+EQ
LEVEL ONLY
AUTO
OFF
ON
ONCE
AUTO
OFF
FREQ LOW
FREQ MID
FREQ HIGH
CUTOFF F
Subwoofer cutoff
frequency
AREA
Tuner interval
LINE ADJ
Line input level
adjustment
L.ADJ 00 – L.ADJ 05
L.ADJ 00
27
AUX ADJ
Auxiliary input level
adjustment
A.ADJ 00 – A.ADJ 05
A.ADJ 00
27
KEY SELECT
External key-operation
mode selection
DVD
27
IF FILTER
Intermediate frequency
filter
DEMO MODE
Demonstration mode
TAG DISP
Tag display
ENGLISH
Preferred Setting Mode (PSM) items
AREA US
AREA EU
DVD
VCR
OFF
WIDE
AUTO
AUTO
27
DEMO OFF
DEMO ON
DEMO ON
27
TAG OFF
TAG ON
TAG ON
27
• Press SEL (select) to finish the setting.
25
EN24-30.KD-SH99[J]f
25
4/3/01, 2:58 PM
ENGLISH
To set the clock display – CLOCK DISP
You can set the clock to be shown on the display
when the unit is turned on.
When shipped from the factory, the clock is set to
be shown on the display.
• CLOCK ON: Clock display is turned on.
• CLOCK OFF: Clock display is turned off.
To select the level meter – LEVEL/EQ
You can select the level display according to your
preference.
When shipped from the factory, this mode is set to
“LEVEL+EQ.”
• EQ ONLY:
• LEVEL+EQ:
Equalizer pattern is displayed.
Equalizer pattern is displayed
along with audio level meter.
• LEVEL ONLY: Audio Level meter illuminates
upward and downward from
center.
To select the dimmer mode – DIMMER
When you turn on the car headlights, the display
automatically dims (Auto Dimmer).
When shipped from the factory, Auto Dimmer
mode is activated.
• AUTO: Activates Auto Dimmer.
• OFF: Cancels Auto Dimmer.
• ON:
Always dims the display.
Note:
Auto Dimmer equipped for this unit may not work
correctly on some vehicles, particularly on those having
a control dial for dimming.
In this case, set the dimmer mode to “ON” or “OFF.”
To turn on/off the key-touch tone – BEEP SW
You can deactivate the key-touch tone if you do
not want it to beep each time you press a button.
When shipped from the factory, the key-touch tone
is activated.
• BEEP ON: Activates the key-touch tone.
• BEEP OFF: Deactivates the key-touch tone.
• P. AMP ON:
Select this mode when not using
external amplifier(s).
• P. AMP OFF: Select this mode when using
external amplifier(s).
To adjust the display contrast level
– CONTRAST
You can adjust the display contrast level among 1
(dark) to 10 (bright). When shipped from the
factory, the display contrast level is set at level 5.
To select the scroll mode – SCROLL
You can select the scroll mode for the disc
information if it consists of more than 10
characters.
When shipped from the factory, Auto Scroll mode
is set to “ONCE.”
• ONCE: Scrolls only once.
• AUTO: Repeats the scroll (5-second
intervals in between).
• OFF:
Cancels Auto Scroll.
Note:
Even if the scroll mode is set to “OFF,” you can scroll
the display by pressing DISP (D) for more than 1
second.
To select the subwoofer cutoff frequency
– CUTOFF F
When a subwoofer is connected to this unit,
select an appropriate cutoff frequency level for
your subwoofer.
When shipped from the factory, the subwoofer
cutoff frequency is set to “FREQ MID.”
• FREQ LOW: Frequencies higher than 50 Hz
are cut off to the subwoofer.
• FREQ MID: Frequencies higher than 80 Hz
are cut off to the subwoofer.
• FREQ HIGH: Frequencies higher than 120 Hz
are cut off to the subwoofer.
To change the AM/FM channel intervals
To turn on/off the power amplifier switch
– AREA
– P. AMP SW
When this unit is shipped from the factory, the
channel intervals are set to 10 kHz for AM and
200 kHz for FM (AREA US settings).
You will have to change the channel intervals
when using this unit in an area other than North
America and South America.
You can switch off the built-in amplifier and send
the audio signals only to the external amplifier(s)
to get clear sounds and to prevent internal heat
buildup inside this unit.
When shipped from the factory, the power
amplifier switch is turned on so that the built-in
amplifier works.
26
EN24-30.KD-SH99[J]f
26
4/3/01, 2:58 PM
• AREA US:
Select this when using this unit in
an area other than North and
South America. (9 kHz for AM and
50 kHz (for manual tuning) /
100 kHz (for searching) for FM)
Select this when using this unit in
North or South America. (10 kHz
for AM and 200 kHz for FM)
Note:
If the channel intervals settings are changed, the names
assigned to the stations will be erased from memory. To
reassign the names, see “Assigning names to the
sources” on pages 28.
To adjust the line input level – LINE ADJ
Adjust the line input level properly when an
external component is connected to the LINE IN
plugs.
When shipped from the factory, the line input level
is set at level 00.
If the input level of the connected component is
not high enough, increase the input level properly.
Without adjusting the line input level, you may be
surprised at a loud sound when you change the
source from the external component to another
source.
To adjust the auxiliary input level
– AUX ADJ
Adjust the auxiliary input level properly when an
external component is connected to the MP3 INPUT
jack.
When shipped from the factory, the auxiliary input
level is set at level 00.
If the input level of the connected component is
not high enough, increase the input level properly.
Without adjusting the line input level, you may be
surprised at a loud sound when you change the
source from the external component to another
source.
To select the target component to operate
through this receiver – KEY SELECT
You can operate either JVC’s DVD player or VCR
through this receiver, by using the number buttons
on the control panel.
When shipped from the factory, these number
buttons are set to be used for the DVD operations.
To use these number buttons on the control panel
for DVD or VCR operations, see page 32.
To change the FM tuner selectivity
– IF FILTER
In some areas, adjacent stations may interfere
with each other. If this interference occurs, noise
may be heard. This unit has been preset to
automatically reduce this interference noise
(“AUTO”) when shipped from the factory.
• AUTO: When this type of interference occurs,
this unit automatically increases the
tuner selectivity so that interference
noise will be reduced. (But the stereo
effect will also be lost.)
• WIDE:
Subject to the interference from
adjacent stations, but sound quality
will not be degraded and the stereo
effect will not be lost.
ENGLISH
• AREA EU:
To turn the demo mode on or off – DEMO MODE
You can turn the demo mode on or off.
When shipped from the factory, “DEMO ON” is
selected.
• DEMO ON: Turns the demo mode on. The
demonstration will start
automatically if no sound comes
in for 3 minutes.
• DEMO OFF: Turns the demo mode off.
Note:
If the unit has been reset (and the power is on),
demonstration will start if no sound comes in for about
10 seconds.
To turn the tag display on or off – TAG DISP
An MP3 file can contain file information called “ID3
Tag” where its album name, performer, track title,
etc. are recorded.
There are two versions–ID3v1 (ID3 Tag version 1)
and ID3v2 (ID3 Tag version 2). This unit is
compatible only with ID3v1.
When shipped from the factory, “TAG ON” is
selected.
• TAG ON: Turns on the ID3 tag display while
playing MP3 files.
* If an MP3 file does not have ID3 tags,
directory and file name appear.
Note:
If you change the setting from “TAG
OFF” to “TAG ON” while playing an
MP3 file, the tag display will be
activated when the next file starts
playing.
• TAG OFF: Turns off the ID3 tag display while
playing MP3 files. (Only the directory
name and file name can be shown.)
27
EN24-30.KD-SH99[J]f
27
4/3/01, 3:45 PM
ENGLISH
Assigning names to the sources 3
You can assign names to station frequencies,
CDs and the external components.
After assigning a name, it will appear on the
display when you select the source.
Select the character set you want while
“ ” is flashing.
Each time you press the button,
the character set changes as
follows:
Capital letters (
Sources
Station frequencies
CDs*
Maximum number of
the characters
up to 10 characters (up to
30 station frequencies
including both FM and AM)
)
Small letters (
Numbers and symbols (
4
)
)
Select a character.
About the available
characters, see page 35.
up to 32 characters
(up to 40 discs)
External components up to 10 characters
(LINE INPUT and
AUX INPUT)
* You cannot assign a name to a CD Text or an MP3 disc.
1
Move the cursor to the next
(or previous) character position.
Select a source you want to assign a
name to.
Each time you press the
button, the source changes
as described on page 7.
2
5
Press and hold SEL (select) for
more than 2 seconds while pressing
DISP (D).
6
7
Repeat steps 3 to 5 until you finish
inputting the name.
Finish the procedure while the last
selected character is flashing.
To erase the input characters
Insert spaces using the same procedure
described above.
When you select an FM station as the source
Notes:
• When you try to assign a name to the 41st disc,
“NAME FULL” appears on the display. (In this
case, delete unwanted names before assignment.)
• When the CD changer is connected, you can assign
names to discs in the CD changer. These names can
also be shown on the display if you insert the discs
in this unit.
28
EN24-30.KD-SH99[J]f
28
4/3/01, 2:58 PM
You can change the angle of the control panel to
four positions.
CAUTION:
NEVER insert your finger
between the control panel
and the unit, as it may get
caught or hurt.
ENGLISH
Changing the control panel
angle
Adjust the angle to the position you want.
Each time you press the button,
the panel angle changes as
follows:
A
B
D
C
When using the remote controller
Press ANGLE ∞ repeatedly. Each time you press the button, the control panel changes its angle — Å,
ı, Ç, then Î positions in sequence.
To restore the control panel to its original position
Press ANGLE 5 repeatedly. Each time you press the button, the control panel changes its angle in
reverse — Î, Ç, ı, then Å positions in sequence.
29
EN24-30.KD-SH99[J]f
29
4/3/01, 2:58 PM
ENGLISH
Detaching the control panel
You can detach the control panel when leaving
the car.
When detaching or attaching the control panel,
be careful not to damage the connectors on the
back of the control panel and on the panel
holder.
Attaching the control panel
1
Insert the left side of the control panel
into the groove on the panel holder.
Detaching the control panel
Before detaching the control panel:
• Be sure to turn off the power
• Be sure to return the control panel to its
original position
1
2
Press the right side of the control
panel to fix it to the panel holder.
Unlock the control panel.
The control panel
comes out toward you.
2
3
Move the control panel to the right,
then pull it out of the unit.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
Put the detached control panel into the
provided case.
Connectors
30
EN24-30.KD-SH99[J]f
30
4/3/01, 2:58 PM
ENGLISH
EXTERNAL COMPONENT OPERATIONS
MP3 player, MD player, etc.
MP3 INPUT*
* This MP3 INPUT is not compatible with digital signals.
Playing external components
You can connect two external components to this
unit.
Connect one to the MP3 INPUT jack on the
control panel, and the other to the LINE IN plugs
on the rear.
You can connect a JVC DVD player or VCR
to the LINE IN plugs.
You can operate a JVC DVD player or VCR
through this receiver using the number
buttons on the control panel.
When you operate the VCR, you have to
change the operation mode of the number
buttons from the DVD operation mode to the
VCR operation mode. (See “To select the
target component to operate through this
receiver – KEY SELECT” on page 27.)
If the input level of the external
components is not high enough, increase
the input level properly.
Without adjusting the input level, you may be
surprised at a loud sound when you change
the source from the external components to
another. (See “To adjust the line input level –
LINE ADJ” and “To adjust the auxiliary input
level – AUX ADJ” on page 27.)
1
Select the external component (AUX
INPUT or LINE INPUT).
When you select a source,
the power automatically
comes on.
Each time you press the
button, the source changes
as described on page 7.
AUX INPUT: To select the component
connected to the MP3 INPUT
jack on the control panel
LINE INPUT: To select the component
connected to the LINE IN plugs
on the rear
CONTINUED ON THE NEXT PAGE
31
EN31-32.KD-SH99[J]f
31
4/3/01, 2:59 PM
ENGLISH
2
Turn on the connected component
and start playing the source.
• If connecting a JVC DVD player or VCR,
you can perform the following operations:
When connecting a DVD player:
: Turns on and off the power.
Starts playback.
• Fast-forward the track when pressed
and held.
• Skip to the beginning of the next tracks
when pressed briefly.
1: • Reverses the track when pressed and
held.
• Go back to the beginning of the current
track when pressed briefly.
Go back to the beginning of the
previous tracks when pressed
consecutively.
7:
Stops playback.
3:
¡:
When connecting a VCR:
: Turns on and off the power.
Starts playback.
Fast-winds a tape when pressed and
held.
1: Rewinds a tape when pressed and held.
7:
Stops playback.
3:
¡:
Note:
When you press the above buttons, the display shows
“VCR” and its operation mode (such as 3, 7).
3
Adjust the volume.
To increase the level.
To decrease the level.
4
Adjust the sound you want.
(See page 21.)
Note:
When you press the above buttons, the display shows
“DVD” and its operation mode (such as 3, 7).
32
EN31-32.KD-SH99[J]f
32
4/3/01, 2:59 PM
ENGLISH
CD CHANGER OPERATIONS
We recommend that you use one of the CH-X series
with your unit.
If you have another CD automatic changer, consult
your JVC car audio dealer for connections.
• For example, if your CD automatic changer is one of
the KD-MK series, you need a cord (KS-U15K) for
connecting it to this unit.
Before operating your CD automatic changer:
• Refer also to the Instructions supplied with your
CD changer.
• If no discs are in the magazine of the CD
changer or the discs are inserted upside down,
“NO DISC” will appear on the display. If this
happens, remove the magazine and set the
discs correctly.
• If “RESET 1” – “RESET 8” appears on the
display, something is wrong with the
connection between this unit and the CD
changer. If this happens, check the connection
and make sure the cords are connected firmly.
Then, press the reset button of the CD
changer.
Playing CDs
Select the CD automatic changer (CD
CHANGER).
Disc number
Track number
To fast-forward or reverse the track
Press and hold ¢
,
while playing a disc, to
fast-forward the track.
Press and hold
4,
while playing a disc, to
reverse the track.
To go to the next track or the previous tracks
Press ¢
briefly, while
playing a disc, to go ahead
to the beginning of the next
track. Each time you press
the button consecutively, the
beginning of the next track is
located and played back.
Press
4 briefly, while
playing a disc, to go back to
the beginning of the current
track. Each time you press
the button consecutively, the
beginning of the previous
tracks is located and played
back.
When you select a source,
the power automatically
comes on.
Each time you press the
button, the source changes
as described on page 7.
Elapsed playing time
33
EN33-34.KD-SH99[J]f
33
4/3/01, 2:59 PM
ENGLISH
To go to a particular disc directly
To play back tracks repeatedly (Repeat Play)
1 Press MODE (M) while playing
a disc. The unit enters the
functions mode.
2 Press RPT (repeat) while still
in the functions mode, so that
the RPT indicator lights up on
the display.
Then, each time you press
RPT, the repeat play mode
changes as follows:
Press the number button corresponding to the disc
number to start its playback (while the CD changer
is playing).
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1
second.
RPT 1
RPT 2
Canceled
Disc number
Mode
RPT
Indicator
Plays repeatedly
RPT 1
Lights
RPT 2
Flashes
The current track (or
specified track).
All tracks of the current
disc (or specified disc).
Elapsed playing time
Track number
Ex.: When disc number 3 is selected
Selecting CD playback modes
To play back only intros (Intro scan)
To play back tracks at random (Random Play)
You can play back the first 15 seconds of each
track sequentially.
1 Press MODE (M) while playing
a disc. The unit enters the
functions mode.
2 Press RND (random) while
still in the functions mode, so
that the RND indicator lights
up on the display.
Then, each time you press
RND, the random play mode
changes as follows:
RND 1
Mode
RND
Indicator
RND 1
Lights
RND 2
Flashes
4
1 Press MODE (M) while playing
a disc. The unit enters the
functions mode.
2 Press INT (intro scan) while still
in the functions mode, so that
“INT” appears on the display.
Then, each time you press INT,
the intro scan mode changes as
follows:
INT 1
INT 2
Canceled
RND 2
Canceled
Plays at random
All tracks of the current
disc, then the tracks of
the next disc and so on.
All tracks of all discs
inserted in the magazine.
Mode
INT 1
INT 2
Indicator
Plays the beginnings
(15 seconds)
Track number Of all tracks on all
flashes
inserted discs.
Disc number Of the first track on
flashes
each inserted disc.
34
EN33-34.KD-SH99[J]f
34
4/3/01, 3:00 PM
ADDITIONAL INFORMATION
ENGLISH
Sound modes (preset value settings)
The list below shows the preset value settings for each sound mode.
If you have changed their settings, you can reset to the factory settings by reassigning the
preset values below. (See page 23 for reassignment procedures.)
Indication
FLAT
Hard Rock
R&B
POP
JAZZ
DanceMusic
Country
Reggae
Classic
User 1
User 2
User 3
Preset equalizing values
FREQ.
50 Hz
80 Hz
80 Hz
120 Hz
80 Hz
50 Hz
50 Hz
80 Hz
120 Hz
50 Hz
50 Hz
50 Hz
WIDTH
1
2
3
1
1
2
4
1
1
1
1
1
LOW LEVEL
00
+03
+03
+02
+03
+04
+02
+03
+03
00
00
00
FREQ.
700 Hz
700 Hz
2 kHz
2 kHz
1 kHz
700 Hz
700 Hz
2 kHz
1 kHz
700 Hz
700 Hz
700 Hz
WIDTH
1
1
2
2
1
1
1
2
1
1
1
1
MID LEVEL
00
00
+01
+01
+01
–02
00
+02
00
00
00
00
FREQ.
8 kHz
8 kHz
12 kHz
12 kHz
8 kHz
8 kHz
12 kHz
12 kHz
8 kHz
8 kHz
8 kHz
8 kHz
HIGH LEVEL
00
+02
+03
+02
+03
+01
+02
+02
+02
00
00
00
Available characters
You can use the following characters to assign names to CDs, radio stations, and external
components. (See page 28.)
Capital letters
Small letters
Numbers and symbols
A
B
C
D
E
a
b
c
d
e
0
1
2
3
4
F
G
H
I
J
f
g
h
i
j
5
6
7
8
9
!
”
#
$
%
&
+
’
(
)
,
–
.
*
/
:
;
<
=
>
?
@
_
`
space
K
L
M
N
O
k
l
m
n
o
P
Q
R
S
T
p
q
r
s
t
U
V
W
X
Y
u
v
w
x
y
Z
space
z
space
35
EN35-39.KD-SH99[J]f
35
4/3/01, 3:00 PM
What appears to be trouble is not always serious. Check the following points before calling a service
center.
Symptoms
CD Changer
FM/AM
General Playback
ENGLISH
TROUBLESHOOTING
Causes
Remedies
• Disc cannot be played
back.
Disc is inserted upside down.
(“DISC ERR” appears on the
display.)
Insert the disc correctly.
• Sound is sometimes
interrupted.
You are driving on rough
roads.
Stop playback while driving on
rough roads.
Disc is scratched.
Change the disc.
Connections are incorrect.
Check the cords and
connections.
The volume level is set to the
minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• “DISC ERR” appears on
the display.
Contents on the disc are not
compatible with the unit.
Change the disc.
• “NO DISC” or “EJECT
ERR” appears on the
display and disc cannot be
ejected.
• No message appears on
the display but disc cannot
be ejected.
The unit may function
incorrectly.
While pressing
, press and
hold 0 for more than 2 seconds.
(Be careful not to drop the disc
when ejecting.)
• This unit or CD changer
does not work at all.
The built-in microcomputer
may function incorrectly due
to noise, etc.
Press the reset button on the
control panel. (See page 2.)
• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.
Signals are too weak.
Store stations manually.
• Static noise while listening
to the radio.
The antenna is not connected
firmly.
Connect the antenna firmly.
• “NO DISC” appears on the
display.
No disc is in the magazine.
Insert a disc.
• “RESET 8” appears on the
display.
This unit is not connected to
a CD changer correctly.
Connect this unit and the CD
changer correctly and press the
reset button of the CD changer.
• Sound cannot be heard
from the speakers.
• “RESET 1” – “RESET 7”
appears on the display.
Press the reset button of the
CD changer.
36
EN35-39.KD-SH99[J]f
36
4/3/01, 3:00 PM
Causes
Remedies
• Disc cannot be played back.
No MP3 files are recorded on
the disc.
Change the disc.
MP3 files do not have the
extension code—mp3 in their
file names.
Add the extension code—mp3
to their file names.
ENGLISH
Symptoms
• Noise is generated.
The file played back is not an
MP3 file (although it has the
extension code—mp3).
Skip to another file or change
the disc.
(Do not add the extension
code—mp3 to non-MP3 files.)
• A longer readout time is
required (“FILE CHECK”
keeps flashing on the
display).
Readout time varies due to
the complexity of the
directory/file configuration.
Do not use too many
hierarchies and directories.
Also, do not record any other
types of audio tracks together
with MP3 files.
• Files cannot be played back
as you have intended them
to play.
Playback order is determined
when the files are recorded.
• Elapsed playing time is not
correct.
This sometimes occurs
during play. This is caused by
how the files are recorded on
the disc.
• “MP3” flashes on the
display.
The current directory does
not contain any MP3 files.
• Correct characters are not
displayed. (Tag Display, e.g.
album name)
This unit can only display
alphabets (capital: A–Z,
small: a–z) and numbers.
MP3 Playback
MP3 files are not recorded in Change the disc.
the format compliant with ISO (Record MP3 files using a
9660 Level 1 or 2.
compliant application.)
Select another directory.
37
EN35-39.KD-SH99[J]f
37
4/3/01, 3:00 PM
ENGLISH
MAINTENANCE
Handling discs
This unit has been designed to reproduce the
discs bearing the following marks.
COMPACT
DIGITAL AUDIO
You can also play back your original CD-Rs
(Recordable) and CD-RWs (Rewritable) either in
audio CD format or in MP3 format.
How to handle discs
Center holder
When removing a disc
from its case, press down
the center holder of the
case and lift the disc out,
holding it by the edges.
• Always hold the disc by
the edges. Do not touch its recording surface.
When storing a disc into its case, gently insert
the disc around the center holder (with the
printed surface facing up).
• Make sure to store discs into the cases after
use.
To keep discs clean
A dirty disc may not play
correctly. If a disc does become
dirty, wipe it with a soft cloth in
a straight line from center to
edge.
To play new discs
New discs may have some
rough spots around the inner
and outer edges. If such a disc
is used, this unit may reject the
disc.
To remove these rough spots, rub the edges with
a pencil or ball-point pen, etc.
Moisture condensation
Moisture may condense on the lens inside the
unit in the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In
this case, eject the disc and leave the unit
turned on for a few hours until the moisture
evaporates.
CAUTIONS:
• Do not insert 8 cm (3 3/16") discs (single CDs)
into the loading slot. (Such discs cannot be
ejected.)
• Do not insert any disc of unusual shape — like a
heart or flower; otherwise, it will cause a
malfunction.
• Do not expose discs to direct sunlight or any heat
source or place them in a place subject to high
temperature and humidity. Do not leave them in a
car.
• Do not use any solvent (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to
clean discs.
When playing a CD-R or CD-RW
You can play back your original CD-Rs or CD-RWs
recorded in audio CD format or in MP3 format.
(However, they may not be played back depending
on their characteristics or recording conditions.)
• User-edited CD-Rs (Recordable) and CD-RWs
(Rewritable), where audio CD tracks are
recorded, can be played back only if they are
already “finalized.”
• Before playing back CD-Rs or CD-RWs, read
their instructions or cautions carefully.
• Some CD-Rs or CD-RWs may not be played
back on this unit because of their disc
characteristics, damage or stain on them, or if
the player’s lens is dirty.
• CD-Rs or CD-RWs are susceptible to high
temperatures or high humidity; so do not leave
them inside your car.
• CD-RWs may require a longer readout time.
(This is caused by the fact that the reflectance
of CD-RWs is lower than for regular CDs.)
About mistracking:
Mistracking may result from driving on
extremely rough roads. This does not damage
the unit and the disc, but will be annoying.
We recommend that you stop disc playback
while driving on such rough roads.
38
EN35-39.KD-SH99[J]f
38
4/3/01, 3:00 PM
AUDIO AMPLIFIER SECTION
CD PLAYER SECTION
Maximum Power Output:
Front: 50 W per channel
Rear: 50 W per channel
Continuous Power Output (RMS):
Front: 19 W per channel into 4 Ω, 40 Hz to
20 000 Hz at no more than
0.8 % total harmonic distortion.
Rear: 19 W per channel into 4 Ω, 40 Hz to
20 000 Hz at no more than
0.8 % total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Equalizer Control Range:
LOW: ±12 dB (50 Hz, 80 Hz, 120 Hz)
MID: ±12 dB (700 Hz, 1 kHz, 2 kHz)
HIGH: ±12 dB (8 kHz, 12 kHz)
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-In Level/Impedance:
LINE IN: 1.5 V/20 kΩ load
MP3 INPUT: 3.5 mm dia. stereo mini jack
(analog)
Line-Out Level/Impedance:
4.0 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Type: Compact disc player
Signal Detection System: Non-contact optical
pickup (semiconductor laser)
Number of channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range:
98 dB
Signal-to-Noise Ratio: 102 dB
Wow and Flutter: Less than measurable limit
MP3 decoding format: MPEG1/2 Audio Layer 3
Max. Bit Rate: 320 Kbps
TUNER SECTION
Frequency Range:
FM: 87.5 MHz to 107.9 MHz
(with channel interval set to 200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM: 530 kHz to 1 710 kHz
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
ENGLISH
SPECIFICATIONS
GENERAL
Power Requirement:
Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
Grounding System: Negative ground
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W x H x D):
Installation Size:
182 mm x 52 mm x 161 mm
(7-3/16" x 2-1/16" x 6-3/8")
Panel Size: 188 mm x 58 mm x 17 mm
(7-7/16" x 2-5/16" x 11/16")
Mass: 1.8 kg (4.0 lbs) (excluding accessories)
Design and specifications subject to change without
notice.
If a kit is necessary for your car, consult your
telephone directory for the nearest car audio
speciality shop.
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
39
EN35-39.KD-SH99[J]f
39
4/3/01, 3:00 PM
http://www.jvcmobile.com
Visit us on-line for
Technical Support & Customer Satisfaction Survey.
US RESIDENTS ONLY
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to Reset
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvcservice.com
We can help you!
VICTOR COMPANY OF JAPAN, LIMITED
EN, SP, FR
COVER.KD-SH99[J]f
V
J
2
C
0401MNMMDWJES
4/3/01, 2:55 PM
KD-SH99
Installation/Connection Manual
Manual de instalación/conexión
Manuel d’installation/raccordement
V
J
LVT0661-001A
[J]
ENGLISH
ESPAÑOL
C
0401MNMMDWJES
EN, SP, FR
FRANÇAIS
• This unit is designed to operate on 12 V DC, NEGATIVE ground
electrical systems.
• Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA.
• Cet appareil est conçu pour fonctionner sur des sources de
courant continu de 12 V à masse NEGATIVE.
INSTALLATION (IN-DASH
MOUNTING)
INSTALACION (MONTAJE EN EL
TABLERO DE INSTRUMENTOS)
INSTALLATION (MONTAGE DANS LE
TABLEAU DE BORD)
• The following illustration shows a typical installation. However,
you should make adjustments corresponding to your specific
car. If you have any questions or require information regarding
installation kits, consult your JVC car audio dealer or a company
supplying kits.
• La siguiente ilustración muestra una instalación típica. Sin
embargo usted deberá efectuar los ajustes correspondientes
a su automóvil. Si tiene alguna pregunta o necesita información
acerca de las herramientas para instalación, consulte con su
concesionario de JVC de equipos de audio para automóviles o
a una compañía que suministra tales herramientas.
• L’illustration suivante est un exemple d’installation typique.
Cependant, vous devez faire les ajustements correspondant à
votre voiture particulière. Si vous avez des questions ou avez
besoin d’information sur des kits d’installation, consulter votre
revendeur d’autoradios JVC ou une compagnie
d’approvisionnement.
1
Before mounting: Press
(Control Panel Release button)
to detach the control panel if already attached.
* When shipped from the factory, the control panel is packed
in the hard case.
2
3
Remove the trim plate.
Remove the sleeve after disengaging the sleeve locks.
1 Stand the unit.
Note: When you stand the unit, be careful not to damage
the fuse on the rear.
2 Insert the 2 handles between the unit and the sleeve, as
illustrated, to disengage the sleeve locks.
3 Remove the sleeve.
1
Antes de instalar: Pulse
(botón de liberación del panel
de control) para desenganchar el panel de control, si ya
está fijado.
* El panel de control se expide de fábrica dentro del
estuche duro.
1
Avant le montage: Appuyer sur
(dèblocage du
panneau de commande) pour èventeullement détacher
le panneau de commande.
* Lorsque ce panneau de commande sort d’usine, il est
rangé dans un étui de transport.
2
3
Retire la placa de guarnición.
2
3
Retirer la plaque d’assemblage.
Install the sleeve into the dashboard.
* After the sleeve is correctly installed in the dashboard, bend
the appropriate tabs to hold the sleeve firmly in place, as
illustrated.
5
Fix the mounting bolt to the rear of the unit’s body and place
the rubber cushion over the end of the bolt.
6
7
8
9
Do the required electrical connections.
4
Attach the control panel.
3
Control panel
Panel de control
Panneau de commande
4
Fije el perno de montaje en la parte trasera del cuerpo de la
unidad y coloque el cojín de goma sobre el extremo del
perno.
6
7
Realice las conexiones eléctricas requeridas.
8
9
Coloque la placa de guarnición.
5
Monter le boulon de montage sur l’arrière du corps de
l’appareil puis passer l’amortisseur en caoutchouc sur
l’extrémité du boulon.
6
7
Réalisez les connexions électriques.
8
9
Coloque el panel de control.
Sleeve
Cubierta
Manchon
Lock Plate
Placa de bloqueo
Plaque de verrouillage
Slot
Ranura
Fente
Attachez la plaque d’ajustage.
Remonter le panneau de commande.
4
Dashboard
Tablero de instrumentos
Tableau de bord
18
4
(7 m
-1 m
/4
")
53
(2 mm
-1
/8
")
5
7
Fuse
Fusible
Fusible
Mounting bolt
Perno de montaje
Boulon de montage
4*
9
Sleeve
Cubierta
Manchon
Control panel
Panel de control
Panneau de commande
TROUBLESHOOTING
The fuse blows.
Are the red and black leads connected correctly?
Power cannot be turned on.
Is the yellow lead connected?
No sound from the speakers.
Is the speaker output lead short-circuited?
Sound is distorted.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in
common?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in
common?
Faites glisser l’appareil dans le manchon jusqu’à ce qu’il
soit verrouillé.
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
8
Trim plate
Placa de guarnición
Plaque d’assemblage
Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans le tableau
de bord, plier les bonnes pattes pour maintenir
fermement le manchon en place, comme montré.
Deslice la unidad dentro de la cubierta hasta que quede
trabada.
Handle
Manija
Poignée
2
•
*
•
*
•
*
•
*
*
3 Retirer le manchon.
Remarque: S’assurer de garder les poignées pour une
utilisation ultérieur, après l’’installation de l’appareil.
Instale la cubierta en el tablero de instrumentos.
5
Attach the trim plate.
1
2 Insérer les 2 poignées entre l’appareil et le manchon
comme indiqué pour désengagé les verrous de
manchon.
* Después de que la cubierta esté correctamente instalada
en el tablero de instrumentos, doble las lengüetas
correspondientes para sostener la cubierta firmemente en
su lugar, tal como se muestra.
Slide the unit into the sleeve.
Libérer les verrous du manchon et retirer le manchon.
1 Poser l’appareil à la verticale.
Remarque: Lorsque vous mettez l’appareil à la
verticale, faire attention de ne pas endommager le
fusible situé sur l’arrière.
1 Ponga la unidad vertical.
Nota: Al poner la unidad vertical, tenga cuidado de no
dañar el fusible provisto en la parte posterior.
2 Inserte las dos manijas entre la unidad y la cubierta tal
como en la ilustración y desenganche los retenes de la
cubierta.
3 Retire la cubierta.
Nota: Después de instalar la unidad, asegúrese de
guardar las manijas para uso futuro.
Note: Be sure to keep the handles for future use after
installing the unit.
4
Retire la cubierta después de desenganchar los retenes de
la cubierta.
See “ELECTRICAL CONNECTIONS.”
Véase “CONEXIONES ELECTRICAS”.
Référez-vous “RACCORDEMENTS
ELECTRIQUES” .
Trim plate
Placa de guarnición
Plaque d’assemblage
LOCALIZACION DE AVERIAS
•
*
•
*
•
*
•
*
*
6
El fusible se quema.
¿Están los conductores rojo y negro correctamente conectados?
No es posible conectar la alimentación.
¿Está el cable amarillo conectado?
No sale sonido de los altavoces.
¿Está el cable de salida del altavoz cortocircuitado?
El sonido presenta distorsión.
¿Está el cable de salida del altavoz conectado a masa?
¿Están los terminales “–” de los altavoces L y R conectados a
una masa común?
• La unidad se calienta.
* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a
una masa común?
EN CAS DE DIFFICULTES
•
*
•
*
•
*
•
*
*
Le fusible saute.
Les fils rouge et noir sont-ils racordés correctement?
L’appareil ne peut pas être mise sous tension.
Le fil jaune est-elle raccordée?
Pas de son des enceintes.
Le fil de sortie de d’enceinte est-il court-circuité?
Le son est déformé.
Le fil de sortie de d’enceinte est-il à la masse?
Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?
• L’appareil devient chaud.
* Le fil de sortie de d’enceinte est-il à la masse?
* Les bornes “–” des enceintes gauche et droit sont-elles mises
ensemble à la masse?
• When installing the unit without using the sleeve
• Instalación de la unidad sin utilizar la cubierta
• Lors de l’installation de l’appareil sans utiliser de manchon
• When using the optional stay
• Cuando emplea un soporte opcional
• Lors de l’utilisation du hauban en option
In a Toyota for example, first remove the car radio and install the unit in its place.
En un Toyota por ejemplo, primero extraiga la radio del automóvil y luego instale la unidad en su
lugar.
Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.
Fire wall
Tabique a prueba de incendios
Cloison
Dashboard
Tablero de instrumentos
Tableau de bord
Washer
Arandela
Rondelle
Lock nut
Tuerca de seguridad
Ecrou d’arrêt
Bracket*
Ménsula*
Support*
Screw (option)
Tornillo (opción)
Vis (en option)
Sleeve
Cubierta
Manchon
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
Nota: Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de
6 mm de longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.
Remarque: Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des
vis d’une longueur de 6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager
l’appareil.
Extracción de la unidad
Retrait de l’appareil
• Before removing the unit, release the rear section.
• Antes de extraer la unidad, libere la sección trasera.
1 Remove the control panel.
1 Extraiga el panel de control.
2 Remove the trim plate.
2 Retire la placa de guarnición.
3 Insert the 2 handles into the slots, as shown. Then, while gently 3 Inserte las 2 manijas entre las ranuras, como se muestra.
pulling the handles away from each other, slide out the unit.
Luego, separe shavemente las manijas y extraiga la unidad.
(Be sure to keep the handles after installing it.)
(Asegúrese de conservar las manijas después de
instalarlo.)
2
1
Handle
Manija
Poignée
Parts list for installation and connection
Lista de piezas para instalación y conexión
The following parts are provided with this unit.
After checking them, please set them correctly.
Con esta unidad se suministran las siguientes piezas.
Después de inspeccionarlas, colóquelas correctamente.
Hard case/Control panel
Estuche duro/Panel de control
Etui de transport/Panneau de
commande
• Avant de retirer l’appareil, libérer la section arrière.
1 Retirer le panneau de commande.
2 Retirer la plaque d’assemblage.
3 Introduire les deux poignées dans les fentes, comme montré.
Puis, tout en tirant doucement les poignées écartées, faire
glisser l’appareil pour le sortir. (S’assurer de conserver les
poignées après l’installation de l’appareil.)
3
Trim plate
Placa de guarnición
Plaque d’assemblage
Control panel
Panel de control
Panneau de commande
Flat type screws (M5 x 6 mm)*
Tornillos tipo plano (M5 x 6 mm)*
Bracket* Vis à tête plate (M5 x 6 mm)*
Ménsula*
Support*
Pocket
Compartimiento
Poche
Mounting bolt
Perno de montaje
Boulon de montage
Removing the unit
* Not included with this unit.
* No suministrado con esta unidad.
* Non fourni avec cet appareil.
Flat type screws (M5 x 6 mm)*
Tornillos tipo plano (M5 x 6 mm)*
Vis à tête plate (M5 x 6 mm)*
Stay (option)
Soporte (opción)
Hauban (en option)
Sleeve
Cubierta
Manchon
Liste des pièces pour l’installation et
raccordement
Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.
Trim plate
Placa de guarnición
Plaque d’assemblage
Remote controller
Control remoto
Télécommande
ATT
AN
GL
E
CD
EQ
Battery
Pila
Pile
CR2025
FM
AM
RD
CH
AU
X
SEL
VO
LUME
AM
-RK1
00
Power cord
Cordón de alimentación
Cordon d’alimentation
Handles
Manijas
Poignées
Washer (ø5)
Arandela (ø5)
Rondelle (ø5)
Lock nut (M5)
Tuerca de seguridad (M5)
Ecrou d’arrêt (M5)
Mounting bolt (M5 x 20 mm)
Perno de montaje (M5 x 20 mm)
Boulon de montage (M5 x 20 mm)
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
ELECTRICAL CONNECTIONS
CONEXIONES ELECTRICAS
RACCORDEMENTS ELECTRIQUES
To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections
before installing the unit. If you are not sure how to install this unit
correctly, have it installed by a qualified technician.
Para evitar cortocircuitos, recomendamos que desconecte el
terminal negativo de la batería y que efectúe todas las conexiones
eléctricas antes de instalar la unidad. Si usted no está seguro de
cómo instalar correctamente la unidad, hágala instalar por un
técnico cualificado.
Pour éviter tout court-circuit, nous vous recommandons de
débrancher la borne négative de la batterie et d’effectuer tous les
raccordements électriques avant d’installer l’appareil. Si l’on n’est
pas sûr de pouvoir installer correctement cet appareil, le faire installer
par un technicien qualifié.
Nota:
Esta unidad está diseñada para funcionar con 12 V de CC, con
sistemas eléctricos de masa NEGATIVA solamente. Si su vehículo
no posee este sistema, será necesario un inversor de tensión, que
puede ser adquirido en los concesionarios de JVC de equipos de
audio para automóviles.
• Reemplace el fusible por uno con la corriente especificada. Si el
fusible se quemase frecuentemente consulte con su
concesionario de JVC de equipos de audio para automóviles.
• Si el ruido fuese un problema...
Esta unidad tiene un filtro de ruido en el circuito de alimentación.
Sin embargo, en algunos vehículos, pueden producirse
chasquidos u otros ruidos indeseados. En tal caso conecte el
terminal de tierra posterior (véase diagrama de conexión) del
receptor al chasis del automóvil, utilizando cordones más gruesos
y cortos tales como alambre de cobre trenzado o de grueso
calibre. Si el ruido persiste, consulte a su concesionario de JVC
de equipos de audio para automóvil.
• La entrada máxima de los altavoces traseros no debe ser no
más que 50 W en el trasero y 50 W en la frontal, con una
impedancia de 4 Ω a 8 Ω.
• Asegúrese de conectar esta unidad a tierra en el chasis del
automóvil.
• El sumidero térmico estará muy caliente después del uso.
Asegúrese de no tocarlo al desmontar esta unidad.
Remarque:
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 V à masse NEGATIVE seulement. Si votre véhicule
n’offre pas ce type d’alimentation, il vous faut un convertisseur de
tension, que vous pouvez acheter chez un revendeur d’autoradios
JVC.
• Remplacer le fusible par un de la valeur précisée. Si le fusible saute
souvent, consulter votre revendeur d’autoradios JVC.
• Si le bruit est un problème...
Cet appareil incorpore un filtre de bruit dans le circuit d’alimentation.
Cependant, avec certains véhicules, quelques claquements ou
autres bruits non désirés risquent de se produire. Si cela arrive,
raccorder la borne arrière de masse de l’appareil au châssis de
la voiture (voir le schéma de raccordement) en utilisant des cordons
les plus gros et les plus courts possibles telle qu’une barre de cuivre
ou une tresse. Si le bruit persiste, consulter votre revendeur
d’autoradios JVC.
• La puissance admissible des enceintes devrait n’être pas plu qu’c
50 W à l’arrière et à 50 W l’avant, avec une impédance de 4 Ω à 8 Ω.
• S’assurer de raccorder la mise à la masse de cet appareil au
châssis de la voiture.
• Le dissipateur de chaleur devient très chaud après usage. Faire
attention de ne pas le toucher en retirant cet appareil.
Note:
This unit is designed to operate only on 12 V DC, NEGATIVE
ground electrical systems. If your vehicle does not have this
system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
• Replace the fuse with one of the specified rating. If the fuse
blows frequently, consult your JVC car audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur.
If this happens, connect the unit’s rear ground terminal (see
connection diagram) to the car’s chassis using shorter and thicker
cords, such as copper braiding or gauge wire. If noise still
persists, consult your JVC car audio dealer.
• Maximum input of the speakers should be no more than 50 W at
the rear and 50 W at the front, with an impedance of 4 Ω to 8 Ω.
• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
Heat sink
Sumidero térmico
Dissipateur de chaleur
ENGLISH
ESPAÑOL
FRANÇAIS
A Typical Connections / Conexiones típicas / Raccordements typiques
Before connecting: Check the wiring in the vehicle carefully not
to fail in connecting this unit. Incorrect connection may cause a
serious damage to this unit.
Antes de la conexión: Verifique atentamente el conexionado del
vehículo para no cometer errores al conectar esta unidad. Una
conexión incorrecta podría producir daños graves en la unidad.
1
Connect the colored leads of the power cord to the car battery,
speakers and automatic antenna (if any) in the following
sequence.
1 Black: ground
2 Yellow: to car battery (constant 12 V)
3 Red: to an accessory terminal
4 Blue with white stripe: to automatic antenna
(200 mA max.)
5 Orange with white stripe: to car light control switch
6 Others: to speakers
1
2
Connect the antenna cord.
2
Conecte el cable de antena.
3
Finally connect the wiring harness to the unit.
3
Por último, conecte a la unidad el cableado preformado.
Conecte los conductores de color del cable de alimentación
a la batería del automóvil, altavoces y antena automática (si
la hubiere) en la secuencia siguiente.
1 Negro: a tierra
2 Amarillo: a la batería del automóvil (12 V constantes)
3 Rojo: a un terminal de accesorio
4 Azul con rayas blancas: a la antena automática
(200 mA máx.)
5 Naranja con rayas blancas: al interruptor de control de
las luces del automóvil
6 Otros: a los altavoces
Avant de commencer la connexion: vérifiez attentivement le
câblage du véhicule pour ne pas connecter incorrectement cet
appareil. Une connexion incorrecte peut endommager
sérieusement l’appareil.
1
Connectez les fils de couleur du cordon d’alimentation à la
batterie de la voiture, aux enceintes et à l’antenne automatique
(s’il y en a une) dans l’ordre suivant.
1 Noir: a la masse
2 Jaune: a la batterie de la voiture (12 Vconstant)
3 Rouge: à la prise accessoire
4 Bleu avec bande blanche: à l’antenne automatique
(200 mA max.)
5 Orange avec bande blanche: à l’interrupteur d’éclairage
de la voiture
6 Autres fils: aux enceintes
2
Connectez le cordon d’antenne.
3
Finalement, connectez le faisceau de fils à l’appareil.
Before connecting the CD changer, make sure that the unit is turned off.
Antes de conectar el cambiador de CD, asegúrese de que la unidad esté apagada.
Avant de connecter le changeur CD, s’assurer que l’unité est éteinte.
Rear ground terminal
Terminal de tierra posterior
Borne arrière de masse
Antenna terminal
Terminal de la antena
Borne de l’antenne
LINE OUT (FRONT)
(see diagram B )
Salida de linea
(Delantera)
(véase diagrama B )
Sortie de ligne (avant)
(voir le diagramme B )
2
When connecting a CD changer, we recommend that you connect one of the CH-X series
CD changers.
• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).
To antenna
A la antena
A l’antenne
Cuando conecte un cambiador de CD, se recomienda utilizar uno de la serie CH-X.
• Si su cambiador de CD es de la serie KD-MK, necesitará un cable opcional (KS-U15K).
JVC CD changer jack
Jack del cambiador de CD de JVC
Prise de changeur CD JVC
JVC CD changer
Cambiador de CD JVC
Changeur de CD JVC
LINE OUT (REAR)
(see diagram B )
Salida de linea
(Trasera)
(véase diagrama B )
Sortie de ligne (arriere)
(voir le diagramme B )
15
Black
Negro
Noir
1
SUBWOOFER OUT
(see diagram B )
Salida de SUBWOOFER
(véase diagrama B )
Sortie de caisson de grave
(voir le diagramme B )
Yellow*1
Amarillo*1
Jaune*1
CONTROL cord
(see diagram B )
Cable de control
(véase diagrama B )
Cordon de commande
(voir le diagramme B )
LINE IN
(see diagram B )
Entrada de linea
(véase diagrama B )
Entrée de ligne
(voir le diagramme B )
Non fourni avec cet appareil.
*
To metallic body or chassis of the car
cuerpo metálico o chasis del automóvil
1 AAuuncorps
métallique ou châssis de la voiture
2
Red
Rojo
Rouge
*
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch)
A un terminal activo del bloque de fusibles conectado a la
batería del automóvil (desviando el interruptor de encendido)
À une borne sous tension du porte-fusible connectée à la batterie
de la voiture (en dérivant l’interrupteur d’allumage)
Blue with white stripe
Azul con rayas blancas
Bleu avec bande blanche
Orange with white stripe
Naranja con rayas blancas
Orange avec bande blanche
*1: Before checking the operation of this unit prior to installation, this
lead must be connected, otherwise power cannot be turned on.
*1: Antes de comprobar el funcionamiento de esta unidad previa
a la instalación, es necesario conectar este cable, de lo
contrario no se podrá conectar la alimentación.
*1: Pour vérifier le fonctionnement de cet appareil avant installation,
ce fil doit être raccordé, sinon l’appareil ne peut pas être mis
sous tension.
Ignition switch
Interruptor de encendido
Interrupteur d’allumage
supplied with this unit.
* Not
No suministrado con esta unidad.
3
15 A fuse
Fusible de 15 A
Fusible 15 A
Lors de la connexion d’un changeur CD, nous vous recommandons d’utiliser un des
changeurs CD de la série CH-X.
• Si votre changeur appartient à la série KD-MK, vous avez besoin d’un cordon optionnel
(KS-U15K).
accessory terminal in the fuse block
3 ToA unanterminal
accesorio del bloque de fusibles
Fuse block
Bloque de fusibles
Porte-fusible
À la prise accessoire du porte-fusible
4
To automatic antenna if any
A la antena automática si la hubiere
À l’antenne automatique s’il y en a une
car light control switch
5 ToAl interruptor
de control
(ILLUMINATION) de las luces del automóvil
À l’interrupteur d’éclairage
de la voiture
6
White with black stripe
Blanco con rayas negras
Blanc avec bande noire
White
Blanco
Blanc
Gray with black stripe
Gris con rayas negras
Gris avec bande noire
Left speaker (front)
Altavoz izquierdo (frontal)
Enceinte gauche (avant)
Gray
Gris
Gris
Green with black stripe
Verde con rayas negras
Vert avec bande noire
Right speaker (front)
Altavoz derecho (frontal)
Enceinte droit (avant)
Green
Verde
Vert
Purple with black stripe
Púrpura con rayas negras
Violet avec bande noire
Left speaker (rear)
Altavoz izquierdo (trasero)
Enceinte gauche (arrière)
Purple
Púrpura
Violet
Right speaker (rear)
Altavoz derecho (trasero)
Enceinte droit (arrière)
PRECAUTIONS on power supply and speaker
connections:
PRECAUCIONES sobre las conexiones de la
fuente de alimentación y de los altavoces:
PRECAUTIONS sur l’alimentation et la
connexion des enceintes:
• DO NOT connect the speaker leads of the power cord to the
car battery; otherwise, the unit will be seriously damaged.
• Connect the black lead (ground), yellow lead (to car battery,
constant 12 V), and red lead (to an accessory terminal) correctly.
• BEFORE connecting the speaker leads of the power cord to the
speakers, check the speaker wiring in your car.
– If the speaker wiring in your car is as illustrated in Fig. 1
and Fig. 2 below, DO NOT connect the unit using that original
speaker wiring. If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect the unit to
the speakers as illustrated in Fig. 3.
– If the speaker wiring in your car is as illustrated in Fig. 3, you
can connect the unit using the original speaker wiring in your car.
– If you are not sure of the speaker wiring of your car, consult
your car dealer.
• NO conecte los conductores de altavoz del cable de
alimentación a la batería de automóvil, pues podrían
producirse graves daños en la unidad.
• Conecte correctamente el conductor negro (a tierra), el
conductor amarillo (a la batería del automóvil, 12 V constantes),
y el conductor rojo (a un terminal de accesorio).
• ANTES de conectar a los altavoces los conductores de altavoz
del cable de alimentación, verifique el conexionado de altavoz
de su automóvil.
– Si el conexionado de altavoz de su automóvil es como
se indica en las Fig. 1 y Fig. 2 de abajo, NO conecte la
unidad utilizando ese conexionado de altavoz original. Si lo
hace, se producirán daños graves en la unidad.
Vuelva a efectuar el conexionado de altavoz de manera que
pueda conectar la unidad a los altavoces de la manera
indicada en la Fig.3.
– Si el conexionado de altavoz de su automóvil es como
se indica en la Fig. 3, podrá conectar la unidad utilizando
el conexionado de altavoz original de su automóvil.
– Si tiene dudas sobre el conexionado de altavoz de su
automóvil, consulte con su concesionario.
• NE CONNECTEZ PAS les fils d’enceintes du cordon
d’alimentation à la batterie; sinon, l’appareil serait
sérieusement endommagé.
• Connectez correctement le fil noir (a la masse), le fil jaune (a la
batterie de la voiture,12 V constant) et le fil rouge (à la prise
accessoire).
• AVANT de connecter les fils d’enceintes du cordon
d’alimentation aux enceintes, vérifiez le câblage des enceintes
de votre voiture.
– Si le câblage des enceintes de votre voiture est réalisé
comme montré sur la Fig. 1 ou Fig. 2 ci-dessous, NE
CONNECTEZ PAS l’appareil en utilisant ce câblage original
d’enceintes. Si vous le faites, l’appareil sera sérieusement
endommagé.
Recommencez le câblage des enceintes de façon que vous
puissiez connecter l’appareil aux enceintes comme montré
sur la Fig. 3.
– Si le câblage des enceintes de votre voiture est comme
montré sur la Fig. 3, vous pouvez connecter l’appareil en
utilisant ce câblage original d’enceintes pour votre voiture.
– Si vous n’êtes pas sûrs du câblage d’enceintes de votre
voiture, consulter le concessionnaire de votre voiture.
+
L -
+
R -
Fig. 1
+
-
+
-
+
L -
+
R -
Fig. 2
+
-
+
-
+
L -
+
R -
+
-
+
-
Fig. 3
Connecting the leads / Conexión de los conductores / Raccordement des fils
Twist the core wires when
connecting.
Retuerza los alambres de
alma para conectarlos.
Torsader les âmes des fils en
les raccordant.
CAUTION / PRECAUCION / PRECAUTION:
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.
• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS utilisés avec de
la bande isolante.
Solder the core wires to connect them securely.
Suelde los alambres de alma para conectarlos con
firmeza.
Souder les âmes desfils pour les raccorder entre eux de
façon sûre.
B Connections Adding Other Equipment / Conexiones para añadir otros equipos / Raccordement pour ajouter d’autres appareils
You can connect an amplifier and other equipment to upgrade
your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
Usted podrá conectar un amplificador y otros equipos para
mejorar el sistema estéreo de su automóvil.
• Conecte el conductor remoto (azul con rayas blancas) al
conductor remoto del otro equipo para poderlo controlar a
través de esta unidad.
Vous pouvez connecter un amplificateur ou autre appareil pour
améliorer votre système autoradio.
• Connectez le fil de commande à distance (bleu avec bande
blanche) au fil de commande à distance de l’autre appareil de
façon qu’il puisse être commandé via cet appareil.
• For amplifier:
– Connect this unit’s line-out terminals to the amplifier’s line-in
terminals.
– Disconnect the speakers from this unit, connect them to
the amplifier. Leave the speaker leads of this unit unused.
– You can switch off the built-in amplifier and send the audio
signals only to the external amplifier(s) to get clear sounds
and to prevent internal heat built-up inside the unit. See page
26 of the Instructions (separate volume).
– The line output level of this unit is kept high to maintain the
hi-fi sounds reproduced from this unit.
When connecting an external amplifier to this unit, turn
down the gain control on the external amplifier to obtain the
best performance from this unit.
• Para el amplificador:
– Conecte los terminales de salida de línea de esta unidad a
los terminales de entrada de línea del amplificador.
– Desconecte los altavoces de esta unidad y conéctelos
al amplificador. Deje los conductores de los altavoces
de esta unidad sin usar.
– Podrá desconectar el amplificador incorporado y enviar las
señales de audio solamente al(los) amplificador(es)
externo(s) para obtener sonidos nítidos y evitar que se
caliente el interior de la unidad. Véase la página 26 de las
instrucciones (volumen separado).
– El nivel de salida de línea de esta unidad permanece alto
para que corresponda con los sonidos de alta fidelidad
reproducidos por esta unidad.
Cuando conecte un amplificador externo a esta unidad,
disminuya el control de ganancia del amplificador externo
para obtener un óptimo rendimiento de esta unidad.
• Pour l’amplificateur:
– Raccorder les fiches de sortie ligne de cet appareil aux fiches
d’entrée ligne de l’amplificateur.
– Déconnectez les enceintes de cet appareil et connectez-les
à l’amplificateur. Laissez les fils d’enceintes de cet appareil
inutilisés.
– Vous pouvez désactiver l’amplificateur intégré et envoyer les
signaux audio uniquement à un ou plusieurs amplificateurs
extérieurs afin d’obtenir un son clair et pour éviter un échauffement
interne de l’appareil. Référez-vous à la page 26 du mode d’emploi
(volume séparé).
– Le niveau de sortie de ligne de cet appareil est maintenu à un
niveau élevé pour maintenir une qualité Hi-Fi pour les sons
reproduits par cet appareil.
Lors de la connexion d’un amplificateur extérieur à cet
appareil, diminuez le réglage du gain sur l’amplificateur extérieur
pour obtenir les meilleures performances de cet appareil.
Amplifier / Amplificador / Amplificateur
Remote lead
Cable remoto
Fil d’alimentation à distance
Rear speakers
Altavoces traseros
Enceintes arrière
L
INPUT
L
R
R
JVC Amplifier
Amplificador de JVC
Amplificateur JVC
Y-connector (not supplied with this unit)
Conector en Y (no suministrado con esta unidad)
Connecteur Y (non fourni avec cet appareil)
Remote lead (Blue with white stripe)
Cable remoto (Azul con rayas blancas)
Fil d’alimentation à distance (Bleu avec bande blanche)
To automatic antenna if any
A la antena automática, si la hubiere
Vers l’antenne automatique, s’il y en a une
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
LINE OUT
(FRONT)
LINE OUT
(REAR)
L
L
R
R
CAUTION / PRECAUCION / PRECAUTION:
• To prevent internal heat built-up inside this unit,
place this unit UNDER the other equipment.
• Para evitar el aumento del calor interior de esta
unidad, póngala DEBAJO del otro equipo.
• Pour éviter un échauffement interne de cet
appareil, placez-le SOUS l’autre appareil.
KD-SH99
L
L
R
R
You can connect
another power
amplifier for front
speakers.
Podrá conectar otro
amplificador de potencia
para los altavoces
delanteros.
Vous pouvez connecter
un autre amplificateur de
puissance pour les
enceintes avant.
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
Front speakers
Altavoces delanteros
Enceintes avant
Subwoofer (SUB WOOFER OUT) / Subwoofer (Salida de SUB WOOFER) / Caisson de grave (Sortie de caisson de grave)
You can connect a subwoofer through an amplifier to reinforce
the bass.
• For their connections, refer to the instructions supplied with
your subwoofer.
Vous pouvez connecter un caisson de grave par un amplificateur
pour renforcer les graves.
• Pour la connexion, référez-vous aux instructions fournies avec
le caisson de grave.
Usted podrá conectar un subwoofer a través de un
amplificador para reforzar los graves.
• Con respecto a sus conexiones, refiérase a las
instrucciones suministradas con sus subwoofer.
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
Subwoofer
Subwoofer
Caisson de grave
SUB WOOFER OUT
Salida de SUBWOOFER
Sortie de caisson de grave
KD-SH99
L
L
L
R
R
R
JVC Amplifier
Amplificador de JVC
Amplificateur JVC
DVD, VCR or TV / DVD, VCR o TV / DVD, Magnétoscope ou Téléviseur
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
L
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
*
TV
R
KV-DV7
You can connect the DVD player (KV-DV7).
Podrá conectar el reproductor DVD (KV-DV7).
Vous pouvez connecter un lecteur de DVD (KV-DV7).
LINE IN
OUTPUT
AUDIO
L
VIDEO
1
KD-SH99
R
REMOTE
SENSOR
INPUT
CONTROL cord
Cable de CONTROL
Cordon de commande
DIGITAL
OUTPUT
(OPTICAL)
Remote control data cord (supplied with KV-DV7)
Cable de datos de control remoto (suministrado con KV-DV7)
Cordon de données de télécommande (fourni avec le KV-DV7)
2
* To the mobile color monitor system or the audio-video input terminal of a stereo
audio-video TV
* Al sistema de monitor de color móvil o al terminal de entrada de audio-vídeo del TV
de audio-vídeo estereofónico
* Au système mobile de moniteur couleur ou aux prises d’entrée audio-vidéo d’un
téléviseur stéréo audio-vidéo