Download Epson ExpressStation Product Information Guide
Transcript
ExpressStation hard disk access light disk&e release latch cover screw power outlet / I reset button poker button port Socketed DS1287 real-time clock, calendar, and 64-byte CMOS RAM for configuration; integrated battery with IO-year life Interfaces Monitor 15-pin, D-shell analog connector; supports standard VGA, multi-frequency, and highresolution monitors Parallel 25-pin, D-shell connector; supports IBM AT compatible or PS/2 compatible (bidirectional) signals; selectable through software serial Two RS-232-C 9-pin, D-shell connectors; asynchronous; up to 56K baud rate SCSI Internal connector for SCSI hard disk drive on drive riser card (single-ended mode only), terminator soldered onto riser card; external SO-pin, fine-pitch connector on back panel for up to seven external SCSI devices (six if internal device is used); external SCSI terminator included LAN One 15-pin AUI (Attachment Unit Interface) D-sub connector; can connect external MAU (Medium Attachment Unit) to provide interface with other networks ‘/“““on slots \ mouse ’ Clock/calendar wrallel oort / serial PO* Optional shadow RAM to copy system, video, or external BIOS information from ROM to RAM; software selectable power light \. diskette access light Shadow RAM I keyboard Doti Computer Specifications One TPE (Twisted Pair Ethernet), 10BASET connector CPU and Memory CPU Intel 25 MHz 486SX, or 33 MHz 486DX microprocessor; simulated 8 MHz processor speed selectable through software or keyboard command System memory BIOS Mini DIN, 6-pin connector for PS/2 compatible mouse or other pointing device Keyboard Mini DIN, 6-pin connector for PS/2 compatible keyboard Option slots 4MB RAM standard on one 4MB SIMM; expandable using 1MB, 2MB, 4MB, or 8MB SIMMs up to 32MB (when 8MB SIMMs are available); SIMMs must be 80ns, 36bit, 72-pin, gold-leaded, fast-page mode type Two 32-bit EISA expansion slots (16-bit and 8-bit ISA compatible) on option card riser board Speaker Internal speaker integrated into power supply; programmable at I/O port 61h; operation controllable through software 256KB two-part system BIOS including video BIOS in two FLASH ROM devices; write-protection available through jumper and software Controllers Diskette Video RAM 1MB standard Cache memory 8KB internal cache integrated into the microprocessor; optional 128KB Intel 485 Turbo Cache module can be installed on main system board (128KB cache module standard on 486/33 model); writethrough, two-way set associative cache memory and controller; operation controllable through software Math coprocessor Mouse Controller on drive riser board supports one 3.5 inch 1.44MB, third-height diskette drive Hard disk Two interfaces on drive riser board support either one IDE drive or one internal SCSI hard disk drive; 3.5inch, third- or half- height form factor Video WD90C30 controller; supports resolutions up to 1024 x 768 in 256 colors; compatible with MDA, CGA, Hercules, EGA, and VGA standards Socket for optional Intel 25 MHz 487SX coprocessor (allowable on 486SX/25 model only) ExpressStation Computer 11/2/92 ExpressStation- ExpressStation LAN Intel 82596CA, 64-byte transmit FIFO, 128-byte receive FIFO; 6-byte Ethernet address per IEEE 802.3 standard stored in writ+protectable FLASH ROM; 25 MHz or 33 MHz operation, based on CPU speed SCSI NCR 5X700 I/O processor for SCSI-II standard; internal FIFO (first-in-first-out), 32-bit address and data busses, internal SCRIPTS processor with fast DMA; 25 MHz or 33 MHz operation, based on CPU speed Mass Storage Bays Up to two internal devices maximum, one third-height, 3.5-inch diskette drive bay; one third- or half-height, 3.5-inch hard disk drive bay for IDE or SCSI drive Power Source Requirements I20-Volt power source requironents AC PM R*ferencr Plug m North America etendards ANSI Powar cord I UVCAS Listed, Type SIT. no.lEI3AWG. or no. 16BAWG. or <HA&. 3OOV, 1 OA or 13A Physical Characteristics Width 15.5 inches (39 cm) Depth 15 inches (38 cm) Height 3 inches (8 cm) Weight 20 lb (9 kg) without peripheral devices Can connect up to seven optional external SCSI devices to external SCSI connector (six maximum if internal SCSI is used) Main System Board Map Keyboard Detachable, two-position, 101 or 102 sculpted keys Layout Countrydependent main typewriter keyboard; numeric/cursor control keypad; four-key cursor control keypad; 12 function keys Power Supply we 142W, fan-cooled, automatic input voltage sensing male AC input socket, female AC output socket; integrated power and reset buttons, panel LEDs, speaker, and fans Input ranges 9Oto132VACandX%Ito264VAC,47to63Hz Option slot power limits Maximum amperage for cards in both option slots: at +5V, 6 Amps; at +12V, 2 Amps; at -5V, 0.3 Amps; at -l2V, 0.3 Amps VIdeoRAM chip sockets ‘I, reoHlme clock I- powr supply connector option card her boord 0 c jumper bbck JlO connector jumper bbck J3 microprocessor math coprocessor socket Power supply current ratings pj 0-O Jll J 1 2 SIMM J13 sockets ‘Jli Environmental Requirements Condition Temperature Humidity Altitude operating rengo 60”to104°F(1Pto400C) 6!Y RH maximum with no herd d&k; with herd disk, nottoexaed78oF(26oCI . . 1 wet bulb 1 to 10,000 it (3.046 m) ExpressStation-2 Non-apmting mnga -tol56“F(4U’toWC) 95O RH maximum et 1M°F(40’C) 1 to 60.000 ft (15.240 m) 5/12/92 ExpressStation Computer ExpressStation 121 Settings Main System Board Jumpers 1 Function 1 Enables you to use the BIOS SETUP program Disables use of the BIOS SETUP program so unauthorized users canno change the settings you have chosen Clears the power-on password Retains the power-on password Clears the current BIOS SETUP information in CMOS memory and sets delault parameters Retains the current BIOS SETUP information in CMOS memory 1 Sets normal FLASH memory operation Sets the FLASH memory 10 operate in recovery mode I1 you unsuccessfully attempted lo download updated BIOS information; allows start of a procedure lo restore the previous BIOS information Jumper pins i-3’ 3-5 The computer contains four blocks (groups) of jumpers: J3, JS, 119, and J21. To access jumper blocks 119 and J21, you must remove any option cards that are installed. You must remove the drive housing to access jumper blocks J3 and JS. 2-4 4-6 9-11 Caution Do not install or remow any option cards when the driw housing is removed from the computer. The housing stabilizes the option card riser board and you could severely damage it if you put stress on it without the support of the drive housing. Also, do not change the settings in the reserved jumper block JlO; these jumpers must remain at their factory settings. 11-13’ 10-12’ 12-14 * Factory setting Each jumper block consists of 14 jumper pins, as shown below. Certain pin numbers and jumper functions are labelled beside each jumper block on the main system board. Main System Board Connectors J1-Internal Serial Port 1 Header Type: 3M style header, double row (Male) 2 GND 4 DTR 6 Serial Data Out 6 ssrlal Data In 10RLSD I2N.C 14fvc IN/C 3Rl 5 CTS 7 RTS 9 DSR 11 tvc 13 N/c J2-Power Connector Type: Single Row Header Style (Male) The tables below list the jumper settings available in each jumper block. Pinout: 13 Settings Jumper pins 2-4 4-6’ Function Wrb-protecis the dlhkstte drtve to prevent unauthorized dow’nloadlng of software onto a diskette Enebks all writes 10 the diskette drive 15 Settings 119 Settings I Jummr oins I 1 Funcilon Indkntes that you are using the standard 512KB size video 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 RAWST +5 +12 -12 GND GND GND GND -5 +5 +5 +5 +5 +5 GND GND -12 HDActive Front Panel Reset Speaker Data J4-Dual Serial Port Connector Indicates that you have installed additlonal video RAM Type: Stacked Dual 9-Pin D-sub (Male) Enables the bulk-in VGA display adapter Disables the bulk-in VGA display adapter Pinout: PC AT standard * Faclory setting J6A-Parallel Port Type: 25-pin Centronics type (Female) Pinout: PC AT standard ExpressStation Computer 5/12/92 ExpressStation-3 ExpressStation J6B-External SCSI Port Connector J17-Twisted Pair Ethernet Connector Type: Fine pitch, 50 pin SCSI-2 (Female) Type: RJ45 (Female) Pinout: 1 ; 4 5 6 ii 9 10 :: 13 :: Data 0 Data 1 Data 2 Data 3 Data 4 Data 5 Data 6 Data 7 Data Parity GND GND GND Terminator Power GND GND SCSI Attn GND GE GND GND GND GND GND GND GND EE GND N/C GND E% EE GND Pinout: 1 2 3 4 EKi GND GND ::: RCVN/C N/C 2 ii J18-AUI Ethernet Connector Type: 15pin D-sub (Female) GND WC N/C GND DI-A GND GND GND VFAUI 01-B Cl-A GND DO-A Cl-B DO-B JXI-VESA Video Pass-thru Connector Ei :zy SCSI Rst SCSI Msg SCSI se1 SCSI CD ~~ TX+ TXRCV+ Type: 3M style, double row header, 26 pin (Male) -0 G N D /CM61 /GND 1-2 jLMt66 lOa4 SYNC EN 1 GND IDEN IDat65 IWTCEN IDml66 Iruc /bt67 GND WTC B L A N K VBHSU jVBVSR IQNO JWC GND /GND IGND /tvc EE? J8-PS/2 Mouse Connector Type: PS/2 (Female) Pinout: 1 : 4 5 Data Miscellaneous N/C GND Video Modes &k J15--PS/2 Keyboard Connector Type: PS/2 (Female) Piiutz 1 2 3 4 i 7 t Data N/C G&ID +5 Clock N/C EL% GND J16-VGA Video Connector Type: 15-pin miniature D-sub (Female) GND N/C GND N/C verl. Bw?c. ExpressStation-4 Blue N/C Green GND How. Bvnc. Red GND GND N/C N/C 5/12/92 ExpressStation Computer ExpressStation System I/O address map System Current usage K)ddmu w22-0023 0020-0021 00BWOF ~~ vorJevke 62352 02357 02357 Funstbn DRAM amtroller ragsters Inlefru~ wntrdler 1 DMA omtmller 1 DMA Controller i405 TurboCache Cdntrotler SlMMs (4 mod&as) 3.5’ 1.44 Meg TEAC Fbppy Hard drsk drive 2 EISA Eqansim Slots 1 cumn(Maxhumeyetem 0.7 A (max) 0.75 A (max) 6 A (mex) .3A (ma) 2.1 A Peak 0.00 A (max) 2 A (max) .3A (max) DMA request led 1 Level ]1765A(max)l .3A syste?n I/o adires5 map K)ddma Ftlnchl occo-ocFF SCSI corltrd m@sters OCBB-OCBF Resewad ocBo-oce7 LAN amd regtsters OcB(McB3 Syslem Ward ID bytes (mad mty) ocsoc27 UASIC regism (optll lacetoll. see -7) 0033 cLAslcwntrolportc OCCQ UABlCWfltrolOOtlB VFF BAA amtmk stop m~isters r NCR 53C7OiI 025QSCA UASIC 62357 040O-MS M644465 0462 62357 02357 azvT7 10461 1 ktendd NMI and m awtrol moister o4ow4oF DMAoontmller 1 exterldedregisters 03Feo3FF serislpatl ozFoaF7 Fkppgdiskmrsronu 035663EF Serttport3 03803DF onboard vtdao controtbr o37sowF Peraltel port 1 03TO-0377 1 SewWary Ftoppydiskoxrtrotter L 02F8-02FF Serialput 62F662E6 Gertprtrt4 027ecwF Psw&t Lxxt 2 OlFGOIF7 IDEtmerfawports 00 b!!Ez Numics~-r DMA dontrotter 2 lnterrud mntrotler 2 BASIC RXttml pod A DMA bwer page register CLASIC RtOS cormtar Reel-time ckxk NMI enable register (write mty) NMI status moister 60, Oow ( KqbwYmousaamtmtter lnta& timer 2 Intmral tkllar 1 CLASIC index ragistars (r&&able to Oc26-Oc27) ExpressStation Computer 162367 62357 WD 16C552 02Q77AA Exp.d WD6DtXO WD 16C552 1 A~lgneddwlca 1 Spare SDLC Drskette drw amtroller Spare (Cascade for CTRL1) Spare Spere spere System interrupts CLASIC CLABIC 02357 02357 a!as7 MAA high page mgtster Lwt Bus Master granted (read rnk) Wlware NMI moister hvrlte anM DRQ 0 (CTRL1) DRQ 1 (CTRL1) DRQ 2 (CTRL1) DRQ 3 (CTRL1) DRQ 4 (CTRL2) DRO 5 (CTRU) DRQ 6 (CTRK) DRQ 7 (CTRL2) yodevke DMA cmtmfter 2 extended mgisters 04DD64Dl kllerNpedg~elcmtml 04C264CF D M A anlmlk 2 extendd redsters k22OCCO-OOOF OOAWOAI 0x2 OC8OX06F 0070 007Mx)71 0070 0061 Direct memory access (DMA) improves system performance by allowing devices to access the system memory directly. This ability is provided by two 82C37-compatible direct memory access controllers (DMACs) contained in the 82357. The seven independent 32-bit DMA channels are listed in the table below along with their associated DMA controller and their device assignments. 1.2A(max) 2.0 A (n-tax) 1 Intemml I 4 NM1 0 4 5 6 7 6 Q 10 11 12 I Exp.d WD XC552 rn.a EYnwrd IDE drnm l4064647SX / EISA / buspIn ah 1 P&v Error Resewad, Intarval Timer 1 I Reserved, Keyboard buffer full Reserved. Cascade Interrupt from slave PIC o n - w serl Port 2 1 2 3 I 1 FunctloMvstom I 118 o n - w Serial Porl 1 User available On-W Floppy On-W Parallel Poll RTC optional SCSIAAN Optbnal SCSI/LAN (defautt LAN) Optbnal SCSI/LAN (dafautl SCSI) On-W Mouse Port if enabled. else user available Rasarvad. Math cnprosassor User avaitabta Optional SCSILAN 110 117 116 115 Q0 126 128 130 132 131 IRQ 9, 10, 11, and 15 can ba set via the ECU for user available, on-board LAN, or on-board SCSI. 62357 a2357 IRQ 0, 1, 2, 6, and 13 canrwl bs used by an add-in card. In PCKf wmpattble systems, IRO 2 was avaitabte br use m the XT bus. In PC-AT compatible systems, IRQ 2 IS not avarlabta for use on the bus. Some older ISAexpansion boards have an optron to use IRQ 2. This should not ba selected when such a board is installed in an ExpressStatton system. CLASIC 62357 UASIC DS 1267 62357 62357 0742 62357 62357 CLASIC 5/12/92 ExpressStation-5 ExpressStation Hard disk drive typzs System Memory Map El22 OKB 512KS HexeMrees mngs Blw 0000-0000 to 0007-FFFF 000&0000 to OOOBFBFF 512KB Base memory 127KB Bese memory enabled in SETUP or Svstem Fun6lton TYP w uds PC seal / SIX6 01 (ifJ 305 - 4 - 126 _ 17 - / 1OMB / user dehnable 14 1733 1612 17 27 26 I1024 1733 1733 1733 30s 903 776 698 976 35 35 37 38 3Q 40 1 Cfmfiguratloi uilllty 639KB 1 OC0NWJO to 000%FFFF / 1 KB 1 Extendad BIOS data segmenl WJKB 766KB ooOA-0000 lo OWB-FFFF CWC-OOW to OOOG7FFF 126KB 32KB SOOKB OOOG6OOO to OCOCFFFF 32KB 832KB OOOD-OOOOtoCOODFFFF 64KB VW0 d&play RAM Vi ROM BIOS 6hadOW area (unused it video shedow is disabled) Built-in SCSI BIOS (unused if SCSI is disabled) Unused (availabte tar acmaon card RAM/ 1 Notaltvideomodesare~~atthesametime.Ywcansavesomememocyby defining which video mod6s you are using. Typicalty, OB-WOOH to OS-7FFFH is only used when you attach a monochrome monllor. Both the taxi and graphic VGA modes are ottan used when you attach a VGA moniior. 2 You can remap the vid6o BIOS to 0CXGW-l using the SEtUP program or the System Conhguration utility il ywr applicatii requwe the video BIOS to reside at th@ b+ii. Do nc4 enable remapping to OC-OCOOH unless your appticauon requIrea It; thl6 6~6s 32KB 01 memory for other us66. Tha built-in video BtOS is atways located al OWCOOH. 3 You oan shadow mrternal ROM BIOS intormatton to memory between OCOOOOH and ODFFFFH using the SETUP program or the system Conttguration utility. The opbon attcws you to begin the shadow btook at aach 15KB boundary. 4 Borne memory managers, such as QEMM-386,. move the exiendad BIOS data area frwn 09-FCOOH to a tower address in base memory to povide more mntiguws memory above the area used by M&DOS. Hard Disk Drives 19 20 21 22 23 24 25 26 / -1 la / 17 17 17 15 17 I5 4 4 6 7 5 I.512 300 1 17 17 300 353 0 -1 -1 330 466 1 17 I 17 17 46 33 17 17 I5SMB 13OMB I42MB I3OMB IOMB 6lMB WOMB unused 40MB 40MB 834 683 16 -1 16 -1 17 3s 124MB unused 202MB 548 761 960 6 6 10 -1 -1 -1 38 38 17 61MB 115MB 61MB I- I- j- IA I I42MB ‘2nYR----i The following table lists the types of hard disk drives you can use in your computer. Check this table and the manual that came with your hard disk to find the correct type for the hard disk drive(s) installed in your computer. Note: Be sure you enter the correct drive type or parametersfor your drive; i,f they are incorrect, the computer will not recognize ymr dti. 5/12/92 u6er definab4e user definable ExpressStation Computer ExpressStation Power-on diagnostic and hot error messages Solutbn C o u n t d o w n Error (Menage SIMM lnstallation nuder EZY The Express.%tion comes with 4MB of memory provided by one 4MB SIMM (single inline memory module) installed on the main system board. You can install additional SIMMs to increase your computers memory to 32MB. There are four SIMM sockets on the main system board. Each socket can contain either a single-sided or doubl+sided SIMM. The SIMMs must all be t3Ons (nanosecond), 3Gbit, 72-pin, goldleaded, fast-page mode SIMMs. 170 /0041 1 Keyboard failure 1 Pomter device failure 1 de&er 1 i Be sure to follow these guidelines when you install SIMMs: 9 All SIMMs must be the l l l same capacity You can Install one, two, or four SIMMs; you cannot install three SIMMs Install multiple SIMMs for the best performance; for example, install two 4MB SIMMs instead of one 8MB SIMM wnnad~ons; contact your dealer it problem parsrsts 0015 o30 all Hard dusk controller Run SETUP and check rmmoh optl0nal ROM bad Chedsum = nn Corracl the address conflict OT rep&a the ROM chip; contact wur dealer II problem persistsRun SETUP and set the time and date Install the SIMMs in the sockets closest to the front of the main system board first. Note: To install 32MB of memory, yaa must remave the 4MB SIMM that came with your system and installfour 8MB SIMMs when they became available. I Error Codes and Messages If the computer finds an error, it reports one of the following types of error messages: l Power-on diagnostic and boot error messages l Error tone codes for fatal errors (that lock up the system) l Error tone codes for non-fatal errors (that do not lock up the system). 0021 I 0019 Tame of day not set 0020 0022 Keyboard is locked To contmua press Eec To enter SETUP press Fl norm ncne none Enable NM Enable cache Eoct Unlcck the keyboard Press Fl to display the error message and hollow the instructions on the screen to run the SETUP program or System Configuration utiltty Power-on Diagnostic and Boot Errors When the poweron diagnostic tests detect an error, the computer displays a message on the screen (as described below) and the speaker beeps twice. If the error occurs before the computer initializes the video display, the speaker sounds a series of beeps (described in the next section). Each error is identified by a message number and a countdown number which the computer uses as it executes the test associated with the error. For example, the following message is countdown number 100 and error message number 0018: 100 lOO181: Error Tone Codes If power-on diagnostic tests detect an error but cannot display an error message, the computer sounds an error tone code. The tone code is a distinct pattern of beeps that identifies the error, such as one beep-two beeps--one beep. If the error is serious (fatal) the computer locks up, but if the error is not serious (non-fatal) you can continue using your computer. The tables below list the fatal and non-fatal error codes. Invalid confipxatim informtim - pleaso mm SEmp The table below lists the power-on diagnostic and boot error messages, and some basic solutions to the problems. Check the appropriate section(s) in this appendix for other solutions. ExpressStation Computer 5/12/92 ExpressStation-7 ExpressStation Error tone codes fo* fatal errors / Error tono coda I l-l-3 l-14 1-2-l l-2-2 I l-2-3 1-3-l l-3-3 l-34 114-l l-4-2 2-l -1 2-l -2 I 2-l-3 2-14 2-2-l 2-2-2 2-2-3 2-24 2-3-l I 2-3-2 2-3-3 2-34 241 I 242 I243 244 3-l -1 3-l -2 3-l 3 3-l 4 3-24 Information Reference List 1 D~~rimtion 1 Real-lime clock wrka/raad failure ROM BIOS checksum faflura Programmable lntenml timer failure DMA inftiaJlzat1on failure I DMA bade realster write/read failure RAM refresh verifkatlon faflure First S4KB RAM chip or data line failure (multffbii) First 64KB RAM oddleven kxtic fatlure I First 64KB RAM address line fatlure First S4KE RAM parity test In pmgress failure Fkst 64KB RAM faflura-btt 0 First 64KB RAM failure-bit 1 First ft4KB RAM tailura-bit 2 First S4KB RAM faflure-bit 3 First S4KE RAM faflura-bft 4 FIrat S4KB RAM failure-bft 5 First 64KB RAM fatlure-bft 6 First S4KB RAM failure-bit 7 First 64KE RAM faflure-blt S 1 First 64KB RAM failura-bk 9 FM 64KB RAM failure-bit A First B4KB RAM failure-bit B FM S4KB RAM faflura-bit C I Flrst 64KB f?AM fatlure-bit D 1 Flmt 64KB RAM Cllurekk F I Engineering Change Notices None. I Technical Information Bulletins None. I Product Support Bulletins None. I Related Documentation TM-EXPRESS PL-EXPRE!SS srKExrRE5s Y743!I9100600 Y743!I9100300 Y74399100200 ExpressStation ExpressStation ExpressStation ExpressStation ExpressStation ExpressStation Service Manual Parts Price List Self Paced Kit Usex’s Guide Software Guide Setup Guide I I First S4KB RAM fallura-bit F Slave DMA mgister failura Master DMA raaistar failure Master Memtpl mask regfster lallura Slave intormpt mask register fallura Keyboadhnouae mntmller test faflure Ewor tone codes for non-fatal errors 1 Error tono coda I 3-34 34-l 342 I DOSC~~~ICNI I Screen memom test hilure I Screen inhlaflzatfan test failure 1 Soreen retmce test failure ExpressStation-8 5/12/92 ExpressStation Computer