Download Delta Electronics KPE-LE02 User's Manual
Transcript
Display Message 20071112 Descriptions Displays “Err”, if the input is invalid. [ 5011666101-K201 How to Operate the Digital Keypad Setting Mode KPE-LE02 Digital Keypad for VFD-E Series START KPE-LE02 VFD-E 系列之數位操作器 Instruction Sheet Please thoroughly read this instruction sheet before installation and putting it into use. The content of this instruction sheet and the driver file may be revised without prior notice. Please consult our distributors or download the most updated instruction version at http://www.delta.com.tw/industrialautomation. X GO START NOTE: In the selected mode, press to set the parameters. Setting parameters 說明書 請詳細閱讀下列說明後才使用本產品,以確保使用安全。 由於產品精益求精,當內容規格有所修正時,請洽詢代理商或至台達網站 (http://www.delta.com.tw/industrialautomation )下載最新版本。 X 鍵盤面板外觀 Description of the Digital Keypad or Success to set parameter. NOTE:In the parameter setting mode, you can press Input data error to the selected mode. To change data Setting direction (When operation source is digital keypad) Dimensions in mm [inch] 25.9 [1.02] 8.6 [0.34] Y 鍵盤面板鍵盤面板尺寸 52.4 [2.06] M3*0.5(2X) 71.9 [2.83] Setting PLC Mode 8.6 [0.34] 52.4 [2.06] 34.3 [1.35] 61.0 [2.40] 8.1 [0.32] 1.5 [0.06] PLC2 mode active 16.3 [0.64] \ 1.5 [0.06] 61.0 [2.40] 8.1 [0.32] 42.4 [1.67] M3*0.5(2X) 16.3 [0.64] Z 25.9 [1.02] 34.3 [1.35] 71.9 [2.83] 42.4 [1.67] Y PLC1 mode active Installation Method 1. Direct installation (unit: mm[inch]) Display Messages Display Message Z 功能顯示項目說明 Descriptions 顯示項目 Displays the AC drive Master Frequency. 說明 顯示驅動器目前的設定頻率 Displays the actual output frequency at terminals U/T1, V/T2, and W/T3. 顯示驅動器實際輸出到馬達的頻率 User defined unit (where U = F x Pr.00.05) 顯示用戶定義之物理量 (U = F x 00-05) Method 2. Mounting by the plate thickness (unit: mm[inch]) A. Thickness=1.2mm[0.05 inches] Displays the output current at terminals U/T1, V/T2, and W/T3. 顯示負載電流 正轉命令 Displays the AC motor drive forward run status. 反轉命令 Displays the AC motor drive reverse run status. 顯示計數值 The counter value (C). 顯示參數項目 Displays the selected parameter. B. Thickness=2.0mm[0.08 inches] Displays the actual stored value of the selected parameter. 外部異常顯示 若由顯示區讀到 End 的訊息(如左圖所示)大約一秒鐘,表示資料已被接受並 自動存入內部存貯器 External Fault. Displays “End” for approximately 1 second if input has been accepted by pressing key. After a parameter value has been set, the new value is automatically stored in memory. To modify an entry, use the keys. 顯示參數內容值 and 若設定的資料不被接受或數值超出時即會顯示 [ 鍵盤面板操作流程 [ 鍵盤面板操作流程 畫面選擇 畫面選擇 START START 重點:在畫面選擇模式中 KPE-LE02 VFD-E 系列之數位操作器 GO START 進入參數設定 重點:在畫面選擇模式中 說明書 參數設定 重點:在參數設定模式中 顯示輸入 資料正確 可往返回畫面選擇模式 參數設定 請詳細閱讀下列說明後才使用本產品,以確保使用安全。 由於產品精益求精,當內容規格有所修正時,請洽詢代理商或至台達網站 (http://www.delta.com.tw/industrialautomation)下載最新版本。 或 顯示輸入 資料錯誤 或 X 鍵盤面板外觀 重點:在參數設定模式中 顯示輸入 資料正確 可往返回畫面選擇模式 顯示輸入 資料錯誤 資料 修改 資料修改 START START 轉向設定 轉向設定 GO START 進入參數設定 (運轉命令來源為數位操作面版時) (運轉命令來源為數位操作面版時) PLC模式設定 PLC模式設定 進入PLC2模式 進入PLC2模式 or Y 鍵盤面板鍵盤面板尺寸 71.9 [2.83] or 25.9 [1.02] 8.6 [0.34] 52.4 [2.06] M3*0.5(2X) \ 安裝方法 方法 1. 直接安裝 (單位: mm[inch]) \ 安裝方法 34.3 [1.35] 42.4 [1.67] 進入PLC1模式 1.5 [0.06] 61.0 [2.40] 8.1 [0.32] 16.3 [0.64] 方法 1. 直接安裝 (單位: mm[inch]) Z 功能顯示項目說明 顯示項目 說明 顯示驅動器目前的設定頻率 方法 2. 依板厚來安裝 (單位: mm[inch]) 顯示驅動器實際輸出到馬達的頻率 A. 板厚=1.2mm[0.05 inches] 顯示用戶定義之物理量 (U = F x 00-05) 方法 2. 依板厚來安裝 (單位: mm[inch]) A. 板厚=1.2mm[0.05 inches] 顯示負載電流 正轉命令 反轉命令 顯示計數值 B. 板厚=2.0mm[0.08 inches] 顯示參數項目 顯示參數內容值 外部異常顯示 若由顯示區讀到 End 的訊息(如左圖所示)大約一秒鐘,表示資料已被接受並自 動存入內部存貯器 若設定的資料不被接受或數值超出時即會顯示 B. 板厚=2.0mm[0.08 inches] 進入PLC1模式