Download Astro Pneumatic 1222 User's Manual
Transcript
Product: 1222 Manual Dimension: 8.5"x 11"/page Date: 2007/06/01 Color: 1222 Black 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET www.astrotools.com 1 YEAR LIMITED WARRANTY •Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for a period of 1 year (except where noted on our price schedule) from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship or other causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this warranty free of charge. The distributor should direct the original user to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase or a copy of warranty card, and a short note explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this warranty. •Astro Pneumatic Tool Co. or its authorized service representatives must perform all warranty repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners. •This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you. All claims must be sent to: SUGGESTED AIR LINE CONNECTION Astro Pneumatic Tool Company 372 Old US Highway 52 South Mt. Airy, NC 27030 PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING 1-800-221-9905 FOR INSTRUCTIONS 1240 - Blue Composite Body 1/4" 90° Angle Die Grinder Unpacking • Composite handle reduces vibration • Rib textured handle provides a firm grip • Lever throttle for feathering control • Compact and lightweight • Front exhaust • Built-in regulator 1240 SPECIFICATIONS: Collet Size: 1/4" Free Speed: 20,000 rpm Overall Length: 5" (127mm) Net Weight: 1lbs. (.45kg) Motor: 1/3hp Air Inlet Thread NPT: HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET When unpacking, check the parts diagram and part number listing on pages 4-5 to make sure all parts are included. If any parts are missing or damage, please call your distributor. Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Sound Pressure: 92.3 db(A) Sound Power: 103.7 db(A) 1240 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1206A - Composite Body 1/4" Medium Die Grinder • Rear exhaust air flow system directs air away from work surface • Compact and lightweight • Built-in regulator • Safety lever 1206A 1206A SPECIFICATIONS: COMPOSITE BODY 1/4" MEDIUM DIE GRINDER Collet Size: 1/4" Free Speed: 22,000 rpm Overall Length: 6-3/4" (171mm) Net Weight: 1-1/8lbs. (.51kg) Motor: 1/3hp Air Inlet Thread NPT: 1/4" Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Page 2 1240 372 Old US Highway 52 South Mount Airy, NC 27030 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER 1206A 372 Old US Highway 52 South Mount Airy, NC 27030 Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. 27 9 16(A) 13 28 31 31P 26 26P 25P 25 1 17 19 11 1A 12 20 10 21 22 14 26 30 6 5 3 10 9 1240-1 T20AH-2 T20AH-3 T20AH-4 T20AH-5 T20AH-6 T20AH-7 T20AH-8 T20AH-9 T20AH-10 T20AH-11 T20AH-12 T20AH-13 T20AH-14 T20AH-15 T20AH-16 T20AH-17 Motor Housing Throttle Valve Throttle Valve Spring Air Regulator Regulator O-Ring Valve Screw O-Ring Valve Screw Safety lever Throttle Lever Pin Ball Bearing Rear End Plate Dowel Pin Rotor Collar Cylinder Rotor Rotor Blade Front End Plate 29 23 11 18A 18AP 22 21 20 19 12 33P 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 14 16 31 17 15 27 Index No. 13 11 33 29 7 4 4 32 24 2 7 18 28 2 32 3 5 6 23 24 COMPOSITE BODY 1/4" MEDIUM DIE GRINDER 8 15 18 Page 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 Index No. 18 19 20 21 22 23 24 26 27 28 29 30 31 31P 32 33 33P Page 4 T20AH-18 T20AH-19 T20AH-20 T20AH-21 T20AH-22 T20AH-23 T20AH-24 T20AH-26 T20AH-27 T20AH-28 T20AH-29 T20AH-30 T20AH-31 T20AH-31P T20AH-32 T20AH-33 T20AH-33P Ball Bearing Pinion Cap Lock Threaded Cap Angle Head Housing Ball Bearing Spindle Gear Woodruff Key Spindle Clamp Nut Collet 1/4",1/8",6mm,3mm Collet Nut Throttle Valve Bushing Throttle Valve O-Ring O-Ring Spanner Wrench(L) Spanner Wrench (S) 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 11P Index No. 1 2 6 4 5 6 7 9 10 11 11P 12 13 14 15 16 17 T210-1 T210-2 T210-3 T210-4 T210-5 T210-6 T210-7 T210-9 T210-10 T210-11 T210-11P T210-12 T210-13 T210-14 T210-15 T210-16 T210-17 Angle Ended Spanner Double Ended Spanner Collet Nut Collet Housing Cap Retainer Spindle Ball Bearing Front End Plate Pin Pin Cylinder Spacer Rotor Rotor Blade Rear End Plate Ball Bearing 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 1 1 Index No. 18A 18AP 19 20 21 22 23 24 25 25P 26 26P 27 28 29 31 32 Page 5 1206A-18 1206A-18P T210-19 T210-20 T210-21 T210-22 T210-23 T210-24 T210-25 T210-25P T210-26 T210-26P T210-27 T210-28 T210-29 T210-31 T210-32 Housing Housing Sleeve Valve Screw O-Ring O-Ring Air Regulator Spring O-Ring Throttle Valve O-Ring Valve Bushing O-Ring Safety lever Throttle Pin Exhaust Deflector Exhaust Washer Inlet Bushing 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Product: 1222 Manual Dimension: 8.5"x 11"/page Date: 2007/06/01 Color: 1222 Black 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET www.astrotools.com 1 YEAR LIMITED WARRANTY •Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for a period of 1 year (except where noted on our price schedule) from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship or other causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this warranty free of charge. The distributor should direct the original user to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase or a copy of warranty card, and a short note explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this warranty. •Astro Pneumatic Tool Co. or its authorized service representatives must perform all warranty repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners. •This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you. All claims must be sent to: SUGGESTED AIR LINE CONNECTION Astro Pneumatic Tool Company 372 Old US Highway 52 South Mt. Airy, NC 27030 PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING 1-800-221-9905 FOR INSTRUCTIONS 1240 - Blue Composite Body 1/4" 90° Angle Die Grinder Unpacking • Composite handle reduces vibration • Rib textured handle provides a firm grip • Lever throttle for feathering control • Compact and lightweight • Front exhaust • Built-in regulator 1240 SPECIFICATIONS: Collet Size: 1/4" Free Speed: 20,000 rpm Overall Length: 5" (127mm) Net Weight: 1lbs. (.45kg) Motor: 1/3hp Air Inlet Thread NPT: HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET When unpacking, check the parts diagram and part number listing on pages 4-5 to make sure all parts are included. If any parts are missing or damage, please call your distributor. Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Sound Pressure: 92.3 db(A) Sound Power: 103.7 db(A) 1240 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1206A - Composite Body 1/4" Medium Die Grinder • Rear exhaust air flow system directs air away from work surface • Compact and lightweight • Built-in regulator • Safety lever 1206A 1206A SPECIFICATIONS: COMPOSITE BODY 1/4" MEDIUM DIE GRINDER Collet Size: 1/4" Free Speed: 22,000 rpm Overall Length: 6-3/4" (171mm) Net Weight: 1-1/8lbs. (.51kg) Motor: 1/3hp Air Inlet Thread NPT: 1/4" Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Page 2 1240 372 Old US Highway 52 South Mount Airy, NC 27030 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER 1206A 372 Old US Highway 52 South Mount Airy, NC 27030 Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. 27 9 16(A) 13 28 31 31P 26 26P 25P 25 1 17 19 11 1A 12 20 10 21 22 14 26 30 6 5 3 10 9 1240-1 T20AH-2 T20AH-3 T20AH-4 T20AH-5 T20AH-6 T20AH-7 T20AH-8 T20AH-9 T20AH-10 T20AH-11 T20AH-12 T20AH-13 T20AH-14 T20AH-15 T20AH-16 T20AH-17 Motor Housing Throttle Valve Throttle Valve Spring Air Regulator Regulator O-Ring Valve Screw O-Ring Valve Screw Safety lever Throttle Lever Pin Ball Bearing Rear End Plate Dowel Pin Rotor Collar Cylinder Rotor Rotor Blade Front End Plate 29 23 11 18A 18AP 22 21 20 19 12 33P 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 14 16 31 17 15 27 Index No. 13 11 33 29 7 4 4 32 24 2 7 18 28 2 32 3 5 6 23 24 COMPOSITE BODY 1/4" MEDIUM DIE GRINDER 8 15 18 Page 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 Index No. 18 19 20 21 22 23 24 26 27 28 29 30 31 31P 32 33 33P Page 4 T20AH-18 T20AH-19 T20AH-20 T20AH-21 T20AH-22 T20AH-23 T20AH-24 T20AH-26 T20AH-27 T20AH-28 T20AH-29 T20AH-30 T20AH-31 T20AH-31P T20AH-32 T20AH-33 T20AH-33P Ball Bearing Pinion Cap Lock Threaded Cap Angle Head Housing Ball Bearing Spindle Gear Woodruff Key Spindle Clamp Nut Collet 1/4",1/8",6mm,3mm Collet Nut Throttle Valve Bushing Throttle Valve O-Ring O-Ring Spanner Wrench(L) Spanner Wrench (S) 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 11P Index No. 1 2 6 4 5 6 7 9 10 11 11P 12 13 14 15 16 17 T210-1 T210-2 T210-3 T210-4 T210-5 T210-6 T210-7 T210-9 T210-10 T210-11 T210-11P T210-12 T210-13 T210-14 T210-15 T210-16 T210-17 Angle Ended Spanner Double Ended Spanner Collet Nut Collet Housing Cap Retainer Spindle Ball Bearing Front End Plate Pin Pin Cylinder Spacer Rotor Rotor Blade Rear End Plate Ball Bearing 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 1 1 Index No. 18A 18AP 19 20 21 22 23 24 25 25P 26 26P 27 28 29 31 32 Page 5 1206A-18 1206A-18P T210-19 T210-20 T210-21 T210-22 T210-23 T210-24 T210-25 T210-25P T210-26 T210-26P T210-27 T210-28 T210-29 T210-31 T210-32 Housing Housing Sleeve Valve Screw O-Ring O-Ring Air Regulator Spring O-Ring Throttle Valve O-Ring Valve Bushing O-Ring Safety lever Throttle Pin Exhaust Deflector Exhaust Washer Inlet Bushing 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Product: 1222 Manual Dimension: 8.5"x 11"/page Date: 2007/06/01 Color: 1222 Black 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1222 HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET www.astrotools.com 1 YEAR LIMITED WARRANTY •Astro Pneumatic Tool Co. warrants our products to the original user against defective material or workmanship for a period of 1 year (except where noted on our price schedule) from the date of 1st use. Astro reserves the right to determine whether the product failed because of defective material, workmanship or other causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products covered under this warranty free of charge. The distributor should direct the original user to return the product (with the exceptions listed below) with the distributor’s name, address, adequate proof of date of purchase or a copy of warranty card, and a short note explaining the problem. Failures caused by accident, alteration, or misuse are not covered by this warranty. •Astro Pneumatic Tool Co. or its authorized service representatives must perform all warranty repairs. Any repair to the product by unauthorized service representatives voids this warranty. The rights under this warranty are limited to the original user and may not be transferred to subsequent owners. •This warranty is in lieu of all other warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Some states do not allow the exclusion of limitations of incidental or consequential damages so the above limitations may not apply to you. All claims must be sent to: SUGGESTED AIR LINE CONNECTION Astro Pneumatic Tool Company 372 Old US Highway 52 South Mt. Airy, NC 27030 PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING 1-800-221-9905 FOR INSTRUCTIONS 1240 - Blue Composite Body 1/4" 90° Angle Die Grinder Unpacking • Composite handle reduces vibration • Rib textured handle provides a firm grip • Lever throttle for feathering control • Compact and lightweight • Front exhaust • Built-in regulator 1240 SPECIFICATIONS: Collet Size: 1/4" Free Speed: 20,000 rpm Overall Length: 5" (127mm) Net Weight: 1lbs. (.45kg) Motor: 1/3hp Air Inlet Thread NPT: HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET When unpacking, check the parts diagram and part number listing on pages 4-5 to make sure all parts are included. If any parts are missing or damage, please call your distributor. Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Sound Pressure: 92.3 db(A) Sound Power: 103.7 db(A) 1240 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER HEAVY-DUTY 1/4" ANGLE HEAD DIE GRINDER & STANDARD DUTY 1/4" DIE GRINDER SET 1206A - Composite Body 1/4" Medium Die Grinder • Rear exhaust air flow system directs air away from work surface • Compact and lightweight • Built-in regulator • Safety lever 1206A 1206A SPECIFICATIONS: COMPOSITE BODY 1/4" MEDIUM DIE GRINDER Collet Size: 1/4" Free Speed: 22,000 rpm Overall Length: 6-3/4" (171mm) Net Weight: 1-1/8lbs. (.51kg) Motor: 1/3hp Air Inlet Thread NPT: 1/4" Air Hose I.D. Size: 3/8" (10mm) Avg. Air Consumption: 3cfm Air Pressure: 90-120psi Page 2 1240 372 Old US Highway 52 South Mount Airy, NC 27030 BLUE COMPOSITE BODY 1/4" 90° ANGLE DIE GRINDER 1206A 372 Old US Highway 52 South Mount Airy, NC 27030 Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. Call 1.800.221.9705 for questions concerning performance of the product or other inquiries. 27 9 16(A) 13 28 31 31P 26 26P 25P 25 1 17 19 11 1A 12 20 10 21 22 14 26 30 6 5 3 10 9 1240-1 T20AH-2 T20AH-3 T20AH-4 T20AH-5 T20AH-6 T20AH-7 T20AH-8 T20AH-9 T20AH-10 T20AH-11 T20AH-12 T20AH-13 T20AH-14 T20AH-15 T20AH-16 T20AH-17 Motor Housing Throttle Valve Throttle Valve Spring Air Regulator Regulator O-Ring Valve Screw O-Ring Valve Screw Safety lever Throttle Lever Pin Ball Bearing Rear End Plate Dowel Pin Rotor Collar Cylinder Rotor Rotor Blade Front End Plate 29 23 11 18A 18AP 22 21 20 19 12 33P 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 14 16 31 17 15 27 Index No. 13 11 33 29 7 4 4 32 24 2 7 18 28 2 32 3 5 6 23 24 COMPOSITE BODY 1/4" MEDIUM DIE GRINDER 8 15 18 Page 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 Index No. 18 19 20 21 22 23 24 26 27 28 29 30 31 31P 32 33 33P Page 4 T20AH-18 T20AH-19 T20AH-20 T20AH-21 T20AH-22 T20AH-23 T20AH-24 T20AH-26 T20AH-27 T20AH-28 T20AH-29 T20AH-30 T20AH-31 T20AH-31P T20AH-32 T20AH-33 T20AH-33P Ball Bearing Pinion Cap Lock Threaded Cap Angle Head Housing Ball Bearing Spindle Gear Woodruff Key Spindle Clamp Nut Collet 1/4",1/8",6mm,3mm Collet Nut Throttle Valve Bushing Throttle Valve O-Ring O-Ring Spanner Wrench(L) Spanner Wrench (S) 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 11P Index No. 1 2 6 4 5 6 7 9 10 11 11P 12 13 14 15 16 17 T210-1 T210-2 T210-3 T210-4 T210-5 T210-6 T210-7 T210-9 T210-10 T210-11 T210-11P T210-12 T210-13 T210-14 T210-15 T210-16 T210-17 Angle Ended Spanner Double Ended Spanner Collet Nut Collet Housing Cap Retainer Spindle Ball Bearing Front End Plate Pin Pin Cylinder Spacer Rotor Rotor Blade Rear End Plate Ball Bearing 1 1 1 1 1 1 1 1 1 2 1 1 1 1 4 1 1 Index No. 18A 18AP 19 20 21 22 23 24 25 25P 26 26P 27 28 29 31 32 Page 5 1206A-18 1206A-18P T210-19 T210-20 T210-21 T210-22 T210-23 T210-24 T210-25 T210-25P T210-26 T210-26P T210-27 T210-28 T210-29 T210-31 T210-32 Housing Housing Sleeve Valve Screw O-Ring O-Ring Air Regulator Spring O-Ring Throttle Valve O-Ring Valve Bushing O-Ring Safety lever Throttle Pin Exhaust Deflector Exhaust Washer Inlet Bushing 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1