Download American Standard Ellisse 2711.XXXW User's Manual

2711.XXXW
SERIES WHIRLPOOL
INSTALLATION INSTRUCTIONS
ELLISSE™
6' X 48"
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
1829mm
(72)
ON/OFF SWITCH
927mm
(36-1/2)
THANK YOU...
OUTLINE OF CUTOUT
1791 X 1181
(70-1/2 X 46-1/2)
102mm
(4)
305mm
(12)
C/L OF
DRAIN
229mm x 356mm
(9 x 14) FLOOR
CUTOUT
1219mm
(48)
RECOMMENDED
FITTING
LOCATION
64X279mm
2-1/2 X 11)
GRAB BAR
FITTING AREA
OPTIONAL
DECK FITTING
AREA
PUMP
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
LEVELING STRINGER
SAFE-T(NOT FOR SUPPORT)
HEATER
REMOVABLE
C/L OF
BLANK
51mm
(2)
OVERFLOW
546mm
(21-1/2)
105mm
(4-1/8)
INTEGRAL
FEET
SUPPORT
ROUGH
FLOOR
64mm
(2-1/2)
121mm
(4-3/4)
GENERAL SPECIFICATIONS FOR 2711 WHIRLPOOL
72 x 48 x 21-1/2 In. (1829 x 1219 x 546mm)
INSTALLED SIZE
148 Lbs. (67 Kg.)
WEIGHT
965 Lbs. (434 Kg.)
WEIGHT w/WATER
95 Gal. (360 L)
GAL. TO OVERFLOW
74 Gal. (280 L)
WHIRLPOOL MIN. OPERATING VOL.
43 x 28 In. (1092 x 711mm)
BATHING WELL AT SUMP
68
x
38
In.
(1727
x 965mm)
BATHING WELL AT RIM
14-5/8 In. (371mm)
WATER DEPTH TO OVERFLOW
40 Lbs./Sq.Ft. (195 Kgs./Sq.m)
FLOOR LOADING
(PROJECTED AREA)
30.3
PTS.
60.8
CUBE (FT 3 )
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
SYSTEM II PUMP
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
• Tile Bead Kit 751755-100*
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
* see your American Standard Distributor
495mm
(19-1/2)
1-1/2 N.P.T.M. THREADS
1-1/2 O.D.TAILPIECE
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
List of Required Tools and Supplies:
Tools
• Level
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
Woodworking Tools
• Personal Safety
Equipment
• Caulking Gun
Supplies
• Nails
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
• Drop Cloth
• 20 amp
GFI Outlet
• Cement, Plaster,
Grout
2.1 HP, 14.4 AMPS ,120V.
2.1 HP, 15.6 AMPS ,120V.
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
752296-100 REV. H
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
INSTALLATION AND FRAMING INSTRUCTIONS
The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs
as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an
access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for
access to the drain components.
NOTE: The apron should not be used as the primary access opening.
1. Position the whirlpool into the installation opening and level the deck, shimming the integral support feet as necessary.
Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).
2. Remove the whirlpool and attach a 2 x 4 stringer to the studs, with the top of the stringer touching the traced line.
3. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final
installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for
suggested opening size and location dimensions.
4. Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims
using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base
consisting of cement (e.g. Sakrete), mortar, or grout will help provide a solid and secure installation.
FIG. 1
495mm
(19-1/2)
TYPICAL RECESS INSTALLATION
TYPICAL PIER TYPE INSTALLATION
AS D ESIR ED
1181mm
(46-1/2)
1791mm
(70-1/2)
CUTOUT
495mm
(19-1/2)
495mm
(19-1/2)
mm)
81
11 -1/2 mm
6
4
19
(
1 2 4 8 ) TH
(
ID
B W
TU
1832mm
(72-1/8)
305mm
(12)
305mm
(12)
AS
DESIRED
LEVELING
STRINGERS
TILE
TILE BEAD
STRIP
610 mm
(24)
LEVELING
SURFACE
610mm
(24)
WATERPROOF
SEALANT
SEALANT
BATH
ACCESS PANEL
ADHESIVE
LEVELING
STRINGER
752296-100 REV. H
BATH
UNLESS AN ACCESS OPENING OF
AT LEAST 12" X 24" (305 X 610MM)
IS PROVIDED, WARRANTY SERVICE
WILL NOT BE PERFORMED.
UNLESS AN ACCESS OPENING OF
AT LEAST 12" X 24" (305 X 610MM)
IS PROVIDED, WARRANTY SERVICE
WILL NOT BE PERFORMED.
(2)
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
2.1 HORSEPOWER MODELS:
The whirlpool should be installed on a 120 vac, 20 amp dedicated circuit. The circuit should be hard-wired from the electrical power
supply panel. The circuit must be a three (3) wire circuit fron the electrical supply panel. A grounded neutral wire and a third wire,
earth ground, are essential. ADDING THE SAFE-T-HEATER REQUIRES A SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.
ELECTRICAL INSTALLATION
SEPARATE 20 AMP
GFCI OUTLET FOR
2.1 HP MODELS
WHIRLPOOL MOUNTED
AIR OR ELECTRONIC SWITCH
OR
WALL TIMER(2.1 HP AIRSWITCH MODELS ONLY)
BLACK
WHITE
120 VAC
PUMP/MOTOR
GND.
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
752296-100 REV. H
(3)
WI RE S E L E CT I O N G U I D E
M a x i m u m d is t a nce f r o m
f u s e box t o mo t o r
M o to r
H i P e rf o rma n c e
Ra ti n g
50'
2. 1
12
100'
150'
200'
1 2 0 V P o w e r Line
10
8
8
The s iz e s s ho w n o n this
cha r t a r e r e co mme ndations
f o r co p p e r co nd uctors
o nl y. Al w a ys f o l low
l o ca l a nd na t io nal
e l e ct r ica l co d e s
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the
whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
stains may be removed using granular Spic and Span® mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing
with a white automotive-type polishing compound and waxing with a liquid wax.
752296-100 REV. H
(4)
SPIC AND SPAN® IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE