Download American Standard Cadet 4021.500 User's Manual
Transcript
CADET® 3 RIGHT HEIGHT™ ELONGATED TOILET VITREOUS CHINA CADET® 3 RIGHT HEIGHT™ ELONGATED TOILET ❑ 2386.012 •Vitreous china •Low-consumption (6.0 Lpf/1.6 gpf) • EverClean® surface inhibits the growth of stain- and odor-causing bacteria, mold, and mildew on the surface •Features the Cadet ® 3 Flushing System •16-1/2" rim height for accessible application •Elongated siphon action jetted bowl •Fully-glazed 2-1/8" trapway with 2" ball pass •Generous 9" x 8" water surface area •Close-coupled tank with flat tank cover for superior storage •Oversized 3" flush valve with chemical resistant flapper •Chrome trip lever •Speed Connect ® tank-to-bowl coupling system •Sanitary dam on bowl with four point tank stabilization •2 color-matched bolt caps •100% factory flush tested • 5 year warranty ❑ 3016.016 Right Height™ Elongated Bowl ❑ 4021.016 Tank Nominal Dimensions: 768 x 438 x 768mm (30-1/4" x 17-1/4" x 30-1/4") Fixture only, seat and supply by others SEE REVERSE FOR ADDITIONAL ROUGHING-IN DIMENSIONS To Be Specified: ❏ Color: ❏ White ❏ Bone ❏ Silver ❏ Linen ❏ Black ❏ Seat: #5325.010 Elongated Champion ® Slow Close solid plastic seat and cover with easy lift off feature ❏ Seat: #5284.016 Elongated EverClean® solid plastic seat and cover ❏ Seat: #5321.110 EverClean ® Elongated Seat with Slow Close Snap-Off Hinges ❏ Supply with stop: Alternative Tank Configurations Available: ❑ 4021.500 Tank complete with Aquaguard Liner ❑ 4021.600 Tank complete with tank cover locking device ❑ 4021.700 Tank complete with Aquaguard Liner and tank cover locking device ❑ 4021.800 Tank complete with trip lever located on right side ❑ 4021.900 Tank complete with tank cover locking device and trip lever located on right side ❑ 4021.950 Tank complete with Aquaguard liner, tank cover locking device, and trip lever on right side NOTES: THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. Compliance Certifications NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED Meets or Exceeds the Following Specifications: SUPPLY SEPARATELY. DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. • ASME A112.19.2M for Vitreous China Fixtures * includes Flush Performance, Ball Pass Diameter, IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. Trap Seal Depth and all Dimensions These measurements are subject to change or cancellation. No responsibility is • Los Angeles Department of Water and Power assumed for use of superseded or voided page Supplementary Purchase Specification for MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND Non-Adjustability ANSI A117.1 REQUIREMENTS FOR ACCESSIBLE AND USABLE BUILDING FACILITIES-CHECK LOCAL CODES. © 2008 AS America Inc. K55 Revised 2/08 CADET® 3 RIGHT HEIGHT™ ELONGATED TOILET VITREOUS CHINA FINISHED WALL 768mm (30-1/4) 25mm ± 6mm (1 ± 1/4) 438mm (17-1/4) 216mm (8-1/2) 464mm (18-1/4) C/L OF SEAT POST HOLES 140mm (5-1/2 CENTERS) 768mm (30-1/4) 102mm (4) SUPPLY AS REQ'D. 419mm (16-1/2) *203mm (8) 213mm (8-3/8) 305mm (12) 356mm (14) FINISHED FLOOR C/L OF OUTLET *352mm (13-7/8) 238mm (9-3/8) *152mm (6) NOTES: THIS TOILET IS DESIGNED TO ROUGH-IN AT A MINIMUM DIMENSION OF 305MM (12") FROM FINISHED WALL TO C/L OF OUTLET. SUPPLY NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY. * DIMENSION SHOWN FOR LOCATION OF SUPPLY IS SUGGESTED. IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided page © 2008 AS America Inc. K56 Revised 2/08