Transcript
KA2410B/ KA2410SB IN-DASH STEREO INSTALLATION KIT FOR 2010 KIA FORTE SCOSCHE 7202 HAZARD 6594 LEFT MOUNTING 7 MOUNTING BRACKET BRACKET 6593 RIGHT MOUNTING BRACKET 7201 PANEL 6552 POCKET INTRODUCTION/PRELIMINARY This premium installation kit is for 2010 Kia Forte vehicles. Included are all the parts you need to mount your car stereo or CD player into your vehicle’s dash. Refer to the individual instruction in this manual to remove your vehicle's factory radio and assemble the kit. CAUTION DISCONNECT YOUR VEHICLE’S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE. WE RECOMMEND THE USE OF A VOLT/OHM METER OVER A TEST LIGHT TO CHECK WIRING. A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE’S COMPUTER AND/OR DIAGNOSTIC SYSTEMS. AVOID ALL FACTORY AIRBAG WIRING - AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH. NOTES * See your vehicle's instructions for any special tools your installation might require. e Read all instructions accompanying your car stereo for proper wiring and mounting instructions. FACTORY WIRING CODES For Factory Wiring Codes go to: www.scosche-cars.com CAR STEREO CONNECTORS HY10B y KAAB PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS. HY10B KAAB : 2008-Up Hyundai 2008-Up Select Kia / x Harness Hyundai Antenna Adapter : LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/ codes and information pertaining to installation of this kit (KA2410B/KA2410SB) in 2010 Kia Forte vehicles. Scosche Industries, Inc. cannot be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of components while using this booklet. If you have any further questions, call our toll free technical help line at: 1-800-621-3695x3 ©2011 SCOSCHE INDUSTRIES, INC. SI KA2410B/SB (3000003) 8/11 FACTORY STEREO REMOVAL 2010 KIA FORTE 1. With panel removal tool (PRT) unclip air vents on the left and right side of the factory stereo. Note: If air vent's trim bezel pops out but not the vent itself, be sure to remove the vent after you have removed the bezel. Extract (4) Phillips head screws securing stereo - (2) on the left and (2) on the right. With PRT unclip stereo, unplug and remove. Remove A/C control panel from factory stereo panel by extracting (4) Phillips head screws from behind. Remove hazard switch assembly from factory stereo panel by extracting (4) Phillips head screws. Retain for reassembly. Unclip hazard button from assembly and retain for reassembly. MOUNTING THE STEREO HAZARD ASSEMBLY FIGURE 1 FIGURE 2 1. Snap factory hazard button into 7202 hazard bracket (Figure 1). 2. Screw hazard switch assembly into 7201 kit panel with (4) Phillips head screws removed during disassembly CS N o Ù у A VS AN \/ (Figure 2). (A AR FACTORY N (AN HAZARD HAZARD 7202 HAZARD 1 Sil e N ASSEMBLY BUTTON BRACKET IM? NV Go SS 7201 6594 LEFT | SINGLE DIN MOUNT 1. Attach 6552 pocket to 7201 panel using screws supplied with kit. a 2. Attach 6593 and 6594 mounting brackets A to 7201 panel using supplied screws. 3. Align and attach aftermarket single din stereo 6593 to brackets using the hardware supplied with RIGHT the aftermarket stereo. Note: If hardware is not BRACKET supplied with aftermarket stereo use hardware from factory stereo. 4. Reconnect stereo, and finish assembly. BRACKET - |» VARIOUS > REAR ; T SUPPORTS 6594 LEFT « BRACKET = IC DOUBLE DIN MOUNT 1. Attach 6593 and 6594 mounting brackets ? to 7201 panel using supplied screws. 3. Align and attach aftermarket double din _ stereo to brackets using the hardware „9 6593 supplied with the aftermarket stereo. 7% RIGHT Note: If hardware is not supplied with “BRACKET aftermarket stereo use hardware from factory stereo. 4. Reconnect stereo, and finish assembly. NOTE: REAR SUPPORT AVAILABLE SEPARATELY. REAR SUPPORT OF THE STEREO ADDS TO THE INSTALLATION’S STRUCTURAL INTEGRITY.