Download Eaton 9135 UPS PPDM

®
Eaton Two-in-One
®
PowerPass Distribution Module
User's Guide
For use with 9135 Two-in-One
5000/6000 VA UPS Models
Class A EMC Statements
FCC Part 15
NOTE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
ICES-003
This Class A Interference Causing Equipment meets all requirements of the Canadian Interference Causing
Equipment Regulations ICES‐003.
Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur du
Canada.
EN 50091-2
Some configurations are classified under EN 50091-2 as “Class‐A UPS for Unrestricted Sales Distribution.” For
these configurations, the following applies:
WARNING This is a Class A‐UPS Product. In a domestic environment, this product may cause radio interference, in
which case, the user may be required to take additional measures.
Eaton and PowerPass are registered trademarks of Eaton Corporation or its subsidiaries and affiliates.
Greenlee is a registered trademark of Greenlee Textron.
ECopyright 2009 Eaton Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be
reproduced in any way without the express written approval of Eaton Corporation.
Requesting a Declaration of Conformity
Units that are labeled with a CE mark comply with the following harmonized standards and EU directives:
S
Harmonized Standards: EN 62040-1-1 (2004-12) and EN 62040-2 (2006-6); IEC 60950 Third Edition
S
EU Directives:
2006/95/EC, Council Directive on equipment designed for use within certain voltage limits
2004/108/EC, Council Directive relating to electromagnetic compatibility
The EC Declaration of Conformity is available upon request for products with a CE mark. For copies of the EC
Declaration of Conformity, contact:
Eaton Power Quality SAS
110, Rue Blaise Pascal
38334 St ISMIER
FRANCE
Phone: +33 476 00 66 66
Special Symbols
The following are examples of symbols used on the UPS or accessories to alert you to important
information:
RISK OF ELECTRIC SHOCK - Indicates that a risk of electric shock is present and the
associated warning should be observed.
CAUTION: REFER TO OPERATOR'S MANUAL - Refer to your operator's manual for
additional information, such as important operating and maintenance
instructions.
This symbol indicates that you should not discard the UPS or the UPS batteries
in the trash. This product contains sealed, lead‐acid batteries and must be
disposed of properly. For more information, contact your local recycling/reuse or
hazardous waste center.
This symbol indicates that you should not discard waste electrical or electronic
equipment (WEEE) in the trash. For proper disposal, contact your local
recycling/reuse or hazardous waste center.
Table of Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
Inspecting the Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PPDM Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PPDM Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardwired PPDM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plug-Receptacle PPDM Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PPDM Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Plug-Receptacle PPDM Rear Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
14
15
19
26
28
28
31
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Using Maintenance Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
5
PPDM Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
6
Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
2
3
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
i
TABLE OF CONTENTS
ii
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 1
Introduction
The PowerPass® Distribution Module (PPDM) is designed to operate
with a 5000/6000 VA Eaton® 9135 uninterruptible power system (UPS).
The PPDM allows you to:
S Replace or upgrade the UPS without losing power to the protected
equipment (see “Using Maintenance Bypass” on page 35).
S Provide surge protection if the UPS is not present.
S Provide extra surge protection when the UPS is present.
Safety Warnings
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that you should follow during installation and
maintenance of the UPS and PPDM. Please read all instructions before operating the
equipment and save this manual for future reference.
DANGER
This UPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are NO USER SERVICEABLE PARTS
inside the UPS.
CAUTION
S To reduce the risk of fire or electric shock, install this UPS in a temperature and humidity
controlled, indoor environment, free of conductive contaminants. Ambient temperature
must not exceed 40°C (104°F). Do not operate near water or excessive humidity
(95% maximum).
S For PPDM models with hardwired outputs, overcurrent protection for the output AC
circuit(s) is to be provided by others.
S For PPDM models with hardwired outputs, suitably rated disconnect switches for the
output AC circuit(s) are to be provided by others.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
1
INTRODUCTION
Sikkerhedsanvisninger
VIGTIGE SIKKERHEDSANVISNINGER
GEM DISSE ANVISNINGER
Denne manual indeholder vigtige instruktioner, som skal følges under installation og
vedligeholdelse af UPS'en og PDU. Læs venligst alle instruktioner inden betjening af
udstyret og gem denne manual mhp. fremtidige opslag.
FARE
Denne UPS indeholder LIVSFARLIG HØJSPÆNDING. Alle reparationer og vedligeholdelse bør
kun udføres af en AUTORISERET SERVICETEKNIKER. Ingen af UPS'ens indvendige dele kan
repareres af brugeren.
ADVARSEL
S Installér denne UPS i et temperatur- og fugtighedskontrolleret indendørsmiljø, frit for
ledende forureningsstoffer for at formindske risikoen for brand og elektrisk stød.
Rumtemperaturen må ikke overstige 40°C. UPS'en bør ikke betjenes nær vand eller høj
fugtighed (maksimalt 95%).
S For PPDM systemer med hårdledningsudgange, skal overstrømsbeskyttelse for
vekslestrømmens udgangskredsløb forsynes af andre.
S For PPDM systemer med hårdledningsudgange, skal egnede, nominelle
afbryderkontakter for vekslestrømmens udgangskredsløb forsynes af andre.
2
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INTRODUCTION
Belangrijke Veiligheidsinstructies
BELANGRIJKE VEILIGHEIDSINSTRUCTIES
BEWAAR DEZE INSTRUCTIES
Deze handleiding bevat belangrijke instructies die u dient te volgen tijdens de installatie en
het onderhoud van de UPS en de PDU. Lees alle instructies voordat u de apparatuur in bedrijf
neemt en bewaar deze handleiding als naslagwerk.
GEVAAR
Deze UPS bevat LEVENSGEVAARLIJKE ELEKTRISCHE SPANNING. Alle reparaties en
onderhoud dienen UITSLUITEND DOOR ERKEND SERVICEPERSONEEL te worden uitgevoerd.
Er bevinden zich GEEN ONDERDELEN in de UPS die DOOR DE GEBRUIKER kunnen worden
GEREPAREERD.
OPGELET
S Teneinde de kans op brand of elektrische schok te verminderen dient deze UPS in een
gebouw met temperatuur‐ en vochtigheidregeling te worden geïnstalleerd, waar geen
geleidende verontreinigingen aanwezig zijn. De omgevingstemperatuur mag 40°C niet
overschrijden. Niet gebruiken in de buurt van water of bij zeer hoge vochtigheid
(max. 95%).
S Voor PPDM systemen met vast‐bedrade uitgangen, moet de overstroombeveiliging voor
wisselstroom uitvoercircuit(s) door anderen worden geleverd.
S Voor PPDM systemen met vast‐bedrade uitgangen, moeten de juiste hoofdschakelaars
voor wisselstroom uitvoercircuit(s) door anderen worden geleverd.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
3
INTRODUCTION
Tarkeita Turvaohjeita
TÄRKEITÄ TURVAOHJEITA - SUOMI
SÄILYTÄ NÄMÄ OHJEET
Tämä käyttöohje sisältää tärkeitä ohjeita, joita on noudatettava UPS-virtalähteen ja PPDM
asennuksen ja huollon yhteydessä. Lue kaikki ohjeet ennen laitteiston käyttöä ja säilytä ohje
myöhempää tarvetta varten.
VAARA
Tämä UPS sisältää HENGENVAARALLISIA JÄNNITTEITÄ. Kaikki korjaukset ja huollot on
jätettävä VAIN VALTUUTETUN HUOLTOHENKILÖN TOIMEKSI. UPS ei sisällä MITÄÄN
KÄYTTÄJÄN HUOLLETTAVIA OSIA.
VARO
S Vähentääksesi tulipalon ja sähköiskun vaaraa asenna tämä UPS sisätiloihin,
joissa lämpötila ja kosteus on säädettävissä ja joissa ei ole virtaa johtavia
epäpuhtauksia. Ympäristön lämpötila ei saa ylittää 40 °C. Älä käytä lähellä vettä ja vältä
kosteita tiloja (95 % maksimi).
S PPDM‐järjestelmissä kiintealla asennuksella: kuormana olevien laitteiden ylivirtasuojaus
ja erotuskytkimet tulee toteuttaa kuormapiireissa.
4
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INTRODUCTION
Consignes de sécurité
CONSIGNES DE SÉCURITÉ IMPORTANTES
CONSERVER CES INSTRUCTIONS
Ce manuel comporte des instructions importantes que vous êtes invité à suivre lors de toute
procédure d'installation et de maintenance de PPDM et de l'onduleur. Veuillez consulter
entièrement ces instructions avant de faire fonctionner l'équipement et conserver ce manuel
afin de pouvoir vous y reporter ultérieurement.
DANGER!
Cet onduleur contient des TENSIONS MORTELLES. Toute opération d'entretien et de
réparation doit être EXCLUSIVEMENT CONFIÉE A UN PERSONNEL QUALIFIÉ AGRÉÉ.
AUCUNE PIÈCE RÉPARABLE PAR L'UTILISATEUR ne se trouve dans l'onduleur.
ATTENTION!
S Pour réduire les risques d'incendie et de décharge électrique, installer l'onduleur
uniquement à l'intérieur, dans un lieu dépourvu de matériaux conducteurs, où la
température et l'humidité ambiantes sont contrôlées. La température ambiante ne doit
pas dépasser 40 °C. Ne pas utiliser à proximité d'eau ou dans une atmosphère
excessivement humide (95 % maximum).
S Pour les models PPDM ayant des sorties câblées, la protection contre une surintensité
pour le(s) circuit(s) de sortie de courant alternatif doit être fournie par un autre
fournisseur.
S Pour les models PPDM ayant des sorties câblées, les interrupteurs de déconnexion
convenables pour le(s) circuit(s) de sortie de courant alternatif doivent être fournie par un
autre fournisseur.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
5
INTRODUCTION
Sicherheitswarnungen
WICHTIGE SICHERHEITSANWEISUNGEN
AUFBEWAREN
Dieses Handbuch enthält wichtige Anweisungen, die Sie während der Installation und
Wartung des USV (Unterbrechungsfreies Stromversorgungssystem) und der PPDM befolgen
müssen. Bitte lesen Sie alle Anweisungen des Handbuches bevor sie mit dem Gerät
arbeiten. Bewaren Sie das Handbuch zum Nachlesen auf.
WARNUNG
Die USV führt lebensgefährliche Spannungen. Alle Reparatur- und Wartungsarbeiten sollten
nur von Kundendienstfachleuten durchgeführt werden. Die USV enthält keine vom Benutzer
zu wartenden Komponenten.
VORSICHT!
S Um die Brand‐ oder Elektroschockgefahr zu verringern, diese USV nur in Gebäuden mit
kontrollierter Temperatur und Luftfeuchtigkeit installieren, in denen keine leitenden
Schmutzstoffen vorhanden sind. Die Umgebungstemperatur darf 40°C nicht übersteigen.
Die USV nicht in der Nähe von Wasser oder in extrem hoher Luftfeuchtigkeit (max. 95 %)
betreiben.
S Für PPDM‐Systeme mit festverdrahteten Eingängen muß der Überstromschutz für die
Ausgangswechselstromkreise anderweitig bereitgestellt werden.
S Für PPDM‐Systeme mit festverdrahteten Ausgängen müssen Trennschalter für die
Ausgangswechselstromkreise mit passendem Nennwert anderweitig bereitgestellt
werden.
6
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INTRODUCTION
Avvisi di sicurezza
IMPORTANTI ISTRUZIONI DI SICUREZZA
CONSERVARE QUESTE ISTRUZIONI
Il presente manuale contiene importanti istruzioni da seguire durante l'installazione e la
manutenzione dell'UPS e dell'PPDM. Leggere integralmente le istruzioni prima di utilizzare
l'apparecchiatura e conservare il presente manuale per futuro riferimento.
PERICOLO
La TENSIONE contenuta in questo gruppo statico di continuità è LETALE. Tutte le operazioni
di riparazione e di manutenzione devono essere effettuate ESCLUSIVAMENTE DA
PERSONALE TECNICO AUTORIZZATO. All'interno del gruppo statico di continuità NON vi
sono PARTI RIPARABILI DALL'UTENTE.
ATTENZIONE
S Per ridurre il rischio di incendio o di scossa elettrica, installare il gruppo statico di
continuità in un ambiente interno a temperatura ed umidità controllata, privo di agenti
contaminanti conduttivi. La temperatura ambiente non deve superare i 40°C. Non
utilizzare l'unità in prossimità di acqua o in presenza di umidità eccessiva (95% max).
S Nei sistemi PPDM provvisti di uscite cablate, i dispositivi di protezione da sovracorrente
per il/i circuito/i a corrente alternata in uscita devono essere forniti da terzi.
S Nei sistemi PPDM provvisti di uscite cablate, i sezionatori di corrente nominale adeguata
per il/i circuito/i a corrente alternata in uscita devono essere forniti da terzi.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
7
INTRODUCTION
Viktig Sikkerhetsinformasion
VIKTIGE SIKKERHETSINSTRUKSJONER
GJEM DISSE INSTRUKSJONENE
Denne håndboken inneholder viktige instruksjoner som du bør overholde ved montering og
vedlikehold av UPS-enheten og PPDM. Les alle instruksjoner før utstyret tas i bruk, og gjem
håndboken til fremtidig referanse.
FARLIG
Denne UPS'en inneholder LIVSFARLIGE SPENNINGER. All reparasjon og service må kun
utføres av AUTORISERT SERVICEPERSONALE. BRUKERE KAN IKKE UTFØRE SERVICE PÅ
NOEN AV DELENE i UPS'en.
FORSIKTIG
S For å redusere fare for brann eller elektriske støt, bør denne UPS'en installeres i et
innendørs miljø med kontrollert temperatur og luftfuktighet som er fritt for ledende,
forurensende stoffer. Romtemperaturen må ikke overskride 40°C. Den må ikke brukes i
nærheten av vann eller ved meget høy luftfuktighet (95% maks.).
S For PPDM systemer med fastkoplete uttak, må overstrømvern for vekselstrømuttak(ene)
stilles til rådighet av andre.
S For PPDM systemer med fastkoplete uttak, må passende utkoplingsbrytere for
vekselstrømuttak(ene) stilles til rådighet av andre.
8
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INTRODUCTION
Regulamentos de Segurança
INSTRUÇÕES DE SEGURANÇA IMPORTANTES
GUARDE ESTAS INSTRUÇÕES
Este manual contém instruções importantes que devem ser seguidas durante a instalação e
manutenção do no-break e da PPDM. Leia todas as instruções antes de operar o
equipamento e guarde este manual para consultá-lo futuramente.
CUIDADO
A UPS contém VOLTAGEM MORTAL. Todos os reparos e assistência técnica devem ser
executados SOMENTE POR PESSOAL DA ASSISTÊNCIA TÉCNICA AUTORIZADO. Não há
nenhuma PEÇA QUE POSSA SER REPARADA PELO USUÁRIO dentro da UPS.
PERIGO
S Para reduzir o risco de incêndios ou choques elétricos, instale a UPS em ambiente
interno com temperatura e umidade controladas e livres de contaminadores condutíveis.
A temperatura ambiente não deve exceder 40°C. Não opere próximo a água ou em
umidade excessiva (máx: 95%).
S Para sistemas PPDM com saídas conectadas, a proteção de sobrecarga para circuitos de
saída de corrente alternada deve ser fornecida por outros.
S Para sistemas PPDM com saídas conectadas, interruptores de desconexão devidamente
qualificados para circuitos de saída de corrente alternada devem ser fornecidos por
outros.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
9
INTRODUCTION
Ïðåäóïðåæäåíèÿ ïî ìåðàì áåçîïàñíîñòè
ÂÀÆÍÛÅ ÓÊÀÇÀÍÈß ÏÎ ÌÅÐÀÌ ÁÅÇÎÏÀÑÍÎÑÒÈ
ÑÎÕÐÀÍÈÒÅ ÝÒÈ ÓÊÀÇÀÍÈß
 äàííîì ðóêîâîäñòâå ñîäåðæàòñÿ âàæíûå èíñòðóêöèè ïî óñòàíîâêå è
îáñëóæèâàíèþ èñòî÷íèêà áåñïåðåáîéíîãî ïèòàíèÿ (ÈÁÏ) è áàòàðåé. Ïåðåä
ðàáîòîé ñ îáîðóäîâàíèåì ïðî÷òèòå âñå èíñòðóêöèè. Ñîõðàíèòå äàííîå
ðóêîâîäñòâî äëÿ äàëüíåéøåãî èñïîëüçîâàíèÿ.
ÎÏÀÑÍÎ
 äàííîì ÈÁÏ èìåþòñÿ ÑÌÅÐÒÅËÜÍÎ ÎÏÀÑÍÛÅ ÍÀÏÐßÆÅÍÈß. Âñå
ðàáîòû ïî ðåìîíòó è îáñëóæèâàíèþ äîëæíû âûïîëíÿòüñÿ ÒÎËÜÊÎ
ÓÏÎËÍÎÌÎ×ÅÍÍÛÌ ÎÁÑËÓÆÈÂÀÞÙÈÌ ÏÅÐÑÎÍÀËÎÌ. Âíóòðè
ÈÁÏ íåò óçëîâ, ÎÁÑËÓÆÈÂÀÅÌÛÕ ÏÎËÜÇÎÂÀÒÅËÅÌ.
ÎÑÒÎÐÎÆÍÎ
S Äëÿ ñíèæåíèÿ îïàñíîñòè ïîæàðà èëè ïîðàæåíèÿ ýëåêòðè÷åñêèì òîêîì
óñòàíàâëèâàéòå ÈÁÏ â çàêðûòîì ïîìåùåíèè ñ êîíòðîëèðóåìûìè
òåìïåðàòóðîé è âëàæíîñòüþ, â êîòîðîì îòñóòñòâóþò ïðîâîäÿùèå
çàãðÿçíÿþùèå âåùåñòâà. Òåìïåðàòóðà îêðóæàþùåãî âîçäóõà íå äîëæíà
ïðåâûøàòü 40°Ñ. Íå ýêñïëóàòèðóéòå óñòðîéñòâî îêîëî âîäû èëè â ìåñòàõ ñ
ïîâûøåííîé âëàæíîñòüþ (ìàêñ. 95%).
S Äëÿ ìîäåëåé ÈÁÏ ñ ïîñòîÿííî çàïàÿííûìè âûõîäíûìè êîíòàêòàìè
óñòðîéñòâî çàùèòû îò ïåðåãðóçêè âûõîäíîãî êîíòóðà (êîíòóðîâ)
ïåðåìåííîãî òîêà ïðèîáðåòàåòñÿ îòäåëüíî.
S Äëÿ ìîäåëåé ÈÁÏ ñ ïîñòîÿííî çàïàÿííûìè âûõîäíûìè êîíòàêòàìè
ñîîòâåòñòâóþùèå ðàçìûêàþùèå ïåðåêëþ÷àòåëè âûõîäíîãî êîíòóðà
(êîíòóðîâ) ïåðåìåííîãî òîêà ïðèîáðåòàþòñÿ îòäåëüíî.
10
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INTRODUCTION
Advertencias de Seguridad
INSTRUCCIONES DE SEGURIDAD IMPORTANTES
GUARDE ESTAS INSTRUCCIONES
Este manual contiene instrucciones importantes que debe seguir durante la instalación y el
mantenimiento del SIE y del PPDM. Por favor, lea todas las instrucciones antes de poner en
funcionamiento el equipo y guarde este manual para referencia en el futuro.
PELIGRO
Este SIE contiene VOLTAJES MORTALES. Todas las reparaciones y el servicio técnico deben
ser efectuados SOLAMENTE POR PERSONAL DE SERVICIO TÉCNICO AUTORIZADO. No hay
NINGUNA PARTE QUE EL USUARIO PUEDA REPARAR dentro del SIE.
PRECAUCIÓN
S Para reducir el riesgo de incendio o de choque eléctrico, instale este SIE en un lugar
cubierto, con temperatura y humedad controladas, libre de contaminantes conductores.
La temperatura ambiente no debe exceder los 40°C. No trabaje cerca del agua o con
humedad excesiva (95% máximo).
S Para los sistemas PPDM con salidas cableadas permanentamente, la protección contra
exceso de corriente para el/los circuito(s) de CA de salida será suministrada por terceros.
S Para los sistemas PPDM con salidas cableadas permanentemente, los interruptores de
desconexión debidamente clasificados para el/los circuito(s) de CA de salida serán
suministrados por terceros.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
11
INTRODUCTION
Säkerhetsföreskrifter
VIKTIGA SÄKERHETSFÖRESKRIFTER
SPARA DESSA FÖRESKRIFTER
Den här anvisningen innehåller viktiga instruktioner som du ska följa under installation och
underhåll av UPS-enheten och PPDM. Läs alla instruktioner innan du använder utrustningen
och spara den här anvisningen för framtida referens.
FARA
Denna UPS-enhet innehåller LIVSFARLIG SPÄNNING. ENDAST AUKTORISERAD
SERVICEPERSONAL får utföra reparationer eller service. Det finns inga delar som
ANVÄNDAREN KAN UTFÖRA SERVICE PÅ inuti UPS-enheten.
VIKTIGT
S Minska risken för brand eller elektriska stötar genom att installera denna UPS-enhet
inomhus, där temperatur och luftfuktighet är kontrollerade och där inga ledande
föroreningar förekommer. Omgivande temperatur får ej överstiga 40°C. Använd inte
utrustningen nära vatten eller vid hög luftfuktighet (max 95 %).
S Överströmsskydd för de utgående växelströmskretsarna ska tillhandahållas av andra för
PPDM‐system med fasta utgångar.
S Bortkopplingsswitchar med passande dimensionering för de utgående
växelströmskretsarna ska tillhandahållas av andra för PPDM‐system med fasta utgångar.
12
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 2
Installation
This section explains:
S Equipment inspection
S UPS setup
S PowerPass Distribution Module (PPDM) installation
S PPDM rear panels
Inspecting the Equipment
If any equipment has been damaged during shipment, keep the shipping
cartons and packing materials for the carrier or place of purchase and file
a claim for shipping damage. If you discover damage after acceptance,
file a claim for concealed damage.
To file a claim for shipping damage or concealed damage: 1) File with
the carrier within 15 days of receipt of the equipment; 2) Send a copy of
the damage claim within 15 days to your service representative.
NOTE Check the battery recharge date on the shipping carton label. If the date has passed
and the batteries were never recharged, do not use the UPS. Contact your service
representative.
PPDM Setup
The 9135 UPSs are designed for flexible configurations and can be
installed in a rack or as a standalone cabinet.
If the UPS is already installed and operating, shut down the UPS before
installing the PPDM. See the following section, “UPS Shutdown.”
For new UPS installations, continue to “PPDM Setup” on page 15.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
13
INSTALLATION
UPS Shutdown
If the UPS is already installed and operating, shut down the UPS:
1.
Prepare your equipment for shutdown.
2.
Press the
button for approximately three seconds.
The UPS beeps once, and the load is no longer protected by the
UPS. It is powered by utility power. If the UPS is set in frequency
converter mode, the equipment will not be powered.
If the utility power is out of tolerance, the UPS will generate a
10 ms output calibrated break.
14
3.
For a full shutdown of UPS and connected load, the upstream
circuit breaker (not included) should be set to the OFF position.
4.
Continue to the following section, “PPDM Setup.”
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
PPDM Setup
To set up the PPDM with the 9135 UPS:
1.
For tower configurations, continue to Step 2; for rack
configurations, continue to Step 7 on page 17.
2.
Tower configuration only. Install pedestal extenders for each
additional cabinet:
For two cabinets, insert the extender into position 3 on the pedestal
(see Figure 1).
For three cabinets or more, insert the extender into position 4 on
the pedestal (see Figure 2).
1 234
1 234
Figure 1. Extending the Pedestals for Two Cabinets
1 234
1 234
1 234
Figure 2. Extending the Pedestals for Three or More Cabinets
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
15
INSTALLATION
NOTE Eaton recommends a minimum of 150 mm (5.9”) free space behind the UPS rear
panel, and a distance of 450 mm (17.7”) between the tower stands.
3.
Carefully position the cabinet upright with the UPS indicators at the
top and place in the pedestals (see Figure 3).
4.
Adjust the pedestals to the size of the UPS and secure the
pedestals with the captive screws.
UPS Indicators
150 mm
(5.9”)
450 mm
(17.7”)
Figure 3. Tower Position with Two Cabinets
16
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
5.
Align each joining bracket with the adjacent cabinet screw holes
and secure with the supplied screws (see Figure 4).
NOTE Joining brackets are required for installations with two or more cabinets.
Joining Bracket
Figure 4. Installing the Joining Brackets
6.
Continue to “Hardwired PPDM Installation” on page 19, or
“Plug-Receptacle PPDM Installation” on page 26.
7.
Rack configuration only. Install the PPDM below the UPS and EBM
as shown in Figure 5.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
17
INSTALLATION
Figure 5. Typical 9135 UPS Installation with EBM and PPDM
8.
18
Continue to “Hardwired PPDM Installation” on page 19, or
“Plug-Receptacle PPDM Installation” on page 26.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
Hardwired PPDM Installation
WARNING
Only qualified service personnel (such as a licensed electrician) shall perform the electrical
installation. Risk of electrical shock.
CAUTION
S For PPDM models with hardwired outputs, overcurrent protection for the output AC
circuit(s) is to be provided by others.
S For PPDM models with hardwired outputs, suitably rated disconnect switches for the
output AC circuit(s) are to be provided by others.
NOTE Do not make unauthorized changes to the UPS or PPDM; otherwise, damage may
occur to your equipment and void your warranty.
The hardwired PPDM models require a dedicated branch circuit that
meets the following requirements:
S 40A minimum circuit with short circuit and overcurrent protection
S 200–240 Vac
S Single phase
S 50/60 Hz
S The breaker must be wallmounted and be readily accessible to the
operator
S Flexible metal conduit (recommended for ease of service and
maintenance)
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
19
INSTALLATION
Figure 6 shows the operation of the UPS with the EPPDMG6000-3U-HW
model, and Figure 7 shows the EPPDMG-6000-3U-HWEU model. For a
more detailed schematic, see Figure 21 on page 40 or Figure 22 on
page 41.
PPDM
PPDM
Input Cord
Terminal 2
L2 In
Terminal 1
L1 In
240
UPS
Out
L1
L1
L2
L2
208
N
Voltage Switch
120
PPDM
Output Cord
240
In
Terminal 4
Load Output 120V (isolated)
120
Terminal 5
Load Output Neutral (isolated)
Terminal 3
Load Output 120V (isolated)
Terminal 6
UPS Output L1
Bypass Switch
Terminal 7
UPS Output L2
Figure 6. UPS with EPPDMG6000-3U-HW PPDM Block Diagram
PPDM
PPDM
Input Cord
Terminal 2
L2 In
Terminal 1
L1 In
Terminal 3
Load Output 230–240V (isolated)
240
UPS
Out
L1
L1
L2
L2
230
240
In
Voltage Switch
PPDM
Output Cord
Bypass Switch
Terminal 4
Load Output 115–120V (isolated)
Terminal 5
Load Output Neutral (isolated)
Terminal 6
UPS Output L1
Terminal 7
UPS Output L2/N
Figure 7. UPS with EPPDMG-6000-3U-HWEU PPDM Block Diagram
20
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
To hardwire the PPDM:
1.
Switch off utility power at the distribution point where the PPDM
will be connected. Be absolutely sure there is no power.
2.
Verify that the PPDM output circuit breaker is in the OFF position
(see Figure 9 on page 23).
3.
Verify that the bypass switch on the PPDM is in the NORMAL
position (see Figure 8).
Bypass Switch
Voltage Switch
Figure 8. PPDM (with Front Cover Removed)
4.
Changing the PPDM voltage switch setting. When the PPDM voltage
switch is set to the 240V position (the default) with 240V input, the
output voltage is 240/120V. When set to the 208V position with
208V input, the output voltage is 208/120V. See Table 1 for a list of
PPDM input/output voltage settings. Figure 8 shows the voltage
switch.
NOTE In most applications, the voltage switch does NOT need changing.
To change the switch position, remove the bracket screw and turn
the switch. Flip the bracket around to fit the new position and
reinstall.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
21
INSTALLATION
Table 1. Hardwired PPDM Input/Output Voltage Settings
EPPDMG6000-3U-HW Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
HV (T6-7)
LV
HV (T6-7)
LV
208
208
120
208
104
220
220
126
220
110
230
230
131
230
115
240
240
138
240
120
EPPDMG-6000-3U-HWEU Models Output Voltage
Input Voltage
(from UPS)
5.
230V Switch Position
Default 240V Switch Position
HV (T6-7)
LV
HV (T6-7)
LV
220
230
115
220
110
230
240
120
230
115
240
250
125
240
120
Remove the wiring access cover and the conduit landing plate and
retain (see Figure 9).
Punch holes in the conduit landing plate for the input and output
conduit using a Greenlee® punch or similar device.
22
6.
Pull the input and output wires through separate conduit, leaving
approximately 0.5m (2 ft) of exposed wire. Attach a flexible metal
fitting to the end of each conduit.
7.
Insert each conduit through a wiring access entry and attach the
conduit fitting to the panel. Strip 9 mm (0.35”) of insulation from the
end of each incoming wire.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
RPO Connector
PPDM Output Cord
Communication Port
RJ-11 Connector
PPDM Input Cord
USB Port
PPDM Output
Circuit Breaker
Wiring Access Cover
Conduit Landing Plate
Figure 9. UPS and Hardwired PPDM Installation
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
23
INSTALLATION
8.
Connect the input and ground wires to the terminal block according
to the PPDM model:
S For the EPPDMG6000-3U-HW model, see Figure 10 and Table 2.
S For the EPPDMG-6000-3U-HWEU model, see Figure 11 and
Table 2.
9.
Connect the output and ground wires to the terminal block
according to the PPDM model:
S For the EPPDMG6000-3U-HW model, see Figure 10 and Table 2.
S For the EPPDMG-6000-3U-HWEU model, see Figure 11 and
Table 2.
Load Output 120V (isolated)
Load Output 120V (isolated)
Load Output Neutral (isolated)
UPS Output Line 1, 208–240V
Source Input Line 2
UPS Output Line 2, 208–240V
Source Input Line 1
Output
Ground
Input
Ground
E4
1
2
3
4
5
6
7
E5
Figure 10. EPPDMG6000-3U-HW Model Terminal Block
Load Output 115–120V (isolated)
Load Output 230–240V (isolated)
Load Output Neutral (isolated)
UPS Output Line 1, 230–240V
Source Input Line 2/N
UPS Output Line 2/N, 230–240V
Source Input Line 1
Input
Earthing
Output
Earthing
E4
1
2
3
4
5
6
7
E5
Figure 11. EPPDMG-6000-3U-HWEU Model Terminal Block
24
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
Table 2. PPDM Wiring Specifications
PPDM Wire Function
Terminal
Position
EPPDMG6000-3U-HW
EPPDMG-6000-3U-HWEU
1
Source Input Line 1
Source Input Line 1
2
Source Input Line 2
Source Input Line 2/N
3
Load Output 120V (isolated)
Load Output 230–240V (isolated)
4
Load Output 120V (isolated)
Load Output 115–120V (isolated)
5
Load Output Neutral (isolated)
Load Output Neutral (isolated)
6
UPS Output Line 1, 208–240V
UPS Output Line 1, 230–240V
7
UPS Output Line 2, 208–240V
UPS Output Line 2/N, 230–240V
E4
Input Ground
Input Earthing
E5
Output Ground
Output Earthing
Terminal Wire
Size Rating*
Tightening
Torque
2–17 mm2
(14–6 AWG)
1.8 ±0.22 Nm
(16 ±2 lb in)
2–5 mm2
(14–10 AWG)
2.26 ±0.22 Nm
(20 ±2 lb in)
8 mm2
(8 AWG)
2.82 ±0.22 Nm
(25 ±2 lb in)
17 mm2
(6 AWG)
3.95 ±0.22 Nm
(35 ±2 lb in)
* Use 2.0 mm2 (14 AWG) 75_C copper wire minimum.
10. Replace the wiring access cover and the conduit landing plate.
11. Continue to “PPDM Startup” on page 28.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
25
INSTALLATION
Plug-Receptacle PPDM Installation
NOTE Do not make unauthorized changes to the UPS or PPDM; otherwise, damage may
occur to your equipment and void your warranty.
To install the PPDM:
1.
Verify that the PPDM output circuit breaker is in the OFF position
(see Figure 9 on page 23).
2.
Verify that the bypass switch on the PPDM is in the NORMAL
position (see Figure 12).
Bypass Switch
Voltage Switch
Figure 12. PPDM (with Front Cover Removed)
3.
Changing the PPDM voltage switch setting. All high voltage outlets,
except the L14-30, use the UPS output voltage. The L14-30 and all
low voltage receptacles use the PPDM transformer, and the voltage
switch determines the voltage. See Table 3 for a complete list of
PPDM input/output voltage settings. Figure 12 shows the voltage
switch.
NOTE In most applications, the voltage switch does NOT need changing.
To change the switch position, remove the bracket screw and turn
the switch. Flip the bracket around to fit the new position and
reinstall.
26
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
Table 3. Plug-Receptacle PPDM Input/Output Voltage Settings
EPPDMG-6000-3U-1 (L6-30) and EPPDMG-6000-3U-2 (L6-20) Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
L6-30R or L6-20R
5-15R
L6-30R or L6-20R
5-15R
208
208
120
208
104
220
220
126
220
110
230
230
131
230
115
240
240
136
240
120
EPPDMG-6000-3U-3 (L5-30) Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
208
120
104
220
126
110
230
131
115
240
136
120
EPPDMG-6000-3U-4 (L14-30) Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
L14-30R
5-15R
L14-30R
5-15R
208
240
120
208
104
220
252
126
220
110
230
262
131
230
115
240
272
136
240
120
EPPDMG-6000-3U-5 (L6-30&L14-30) Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
L6-30R
L14-30R
5-15R
L6-30R
L14-30R
5-15R
208
208
240
120
208
208
104
220
220
252
126
220
220
110
230
230
262
131
230
230
115
240
240
272
136
240
240
120
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
27
INSTALLATION
EPPDMG-6000-3U-6 (L6-30) and EPPDMG-6000-3U-7 (L6-20) Models Output Voltage
Input Voltage
(from UPS)
208V Switch Position
Default 240V Switch Position
L6-30R or L6-20R
5-20R
L6-30R or L6-20R
5-20R
208
208
120
208
104
220
220
126
220
110
230
230
131
230
115
240
240
136
240
120
4.
Neutral-to-Ground Bonding. The PPDM has a neutral-to-ground (N-G
or neutral-to-earth) bonding screw as required under safety
regulations issued by various regulatory agencies. If the
neutral-to-ground connection is not needed, remove the screw to
remove the bond between neutral and ground.
See “Plug-Receptacle PPDM Rear Panels” on page 31 for the
neutral-to-ground screw locations.
5.
Continue to the following section, “PPDM Startup.”
PPDM Startup
To start up the PPDM with a 9135 UPS, continue to the following
section, “9135 UPS Startup.”
UPS Startup
To start up the PPDM with a 9135 UPS:
28
1.
If you are installing a remote power-off (RPO) switch, install the
switch before powering on the UPS. Refer to “RPO Installation” in
the UPS user's guide for instructions.
2.
Refer to the UPS user's guide for recommended upstream
protection. For EU models, also refer to the recommendations for
downstream protection.
3.
Plug the input and output cords of the PPDM into the input and
output power connectors on the UPS power cables (see Figure 13).
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
Output
Connection
Input
Connection
Power
Connection
Figure 13. PPDM and 9135 UPS Connections
4.
Verify that the UPS internal battery connector is connected (refer to
the UPS user's guide).
5.
Switch all battery circuit breakers to the ON ( | ) position.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
29
INSTALLATION
6.
Set the upstream circuit breaker (not included) to the ON position.
7.
Hardwired PPDM models only. Switch the main utility breaker on.
The equipment is powered by utility power, but not protected by
the UPS.
Batteries are recharging. An eight-hour recharge period is necessary
to get full backup time.
The
8.
and
indicators illuminate.
Plug-receptacle PPDM models only. Plug the supplied power cord into
the input connector on the PPDM rear panel.
The equipment is powered by utility power, but not protected by
the UPS.
Batteries are recharging. An eight-hour recharge period is necessary
to get full backup time.
The
9.
and
indicators illuminate.
button until you hear the UPS beep
Press and hold the
(approximately three seconds).
After the UPS is turned on, it conducts a self-test and enters
indicator remains on and the
indicator
Normal mode. The
turns off indicating that power is available to your equipment.
10. Confirm the UPS output voltage through the front panel and verify
that it matches the PPDM output voltage (see Table 3 on page 27).
CAUTION
Failure to match the UPS output voltage may result in a hazardous condition, including
damage to the UPS or to the load.
30
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
11. Plug-receptacle PPDM models only. Plug the equipment to be
protected into the PPDM output receptacle(s).
NOTE DO NOT protect laser printers with the UPS because of the exceptionally high power
requirements of the heating elements.
12. Switch the PPDM output circuit breaker to the ON ( | ) position.
NOTE The PPDM output circuit breaker (disconnect switch) disconnects power to the
output on the PPDM rear panel, but does NOT shut off power to the UPS (opening the
upstream protection would be required).
13. Install the PPDM front cover (shipped separately).
14. To change the UPS default settings, refer to “Display Functions” in
the UPS user's guide.
Plug-Receptacle PPDM Rear Panels
This section shows the rear panels of the plug-receptacle PPDM
models.
NOTE The rear panel for hardwired models is shown in Figure 9 on page 23.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
31
INSTALLATION
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(eight 5-15R)
Output Receptacle (L6-30)
Neutral-to-Ground Bonding Screw
Figure 14. EPPDMG-6000-3U-1 (L6-30)
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(eight 5-15R)
Output Receptacle (L6-20)
Neutral-to-Ground Bonding Screw
Figure 15. EPPDMG-6000-3U-2 (L6-20)
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(eight 5-15R)
Output Receptacle (L5-30)
Neutral-to-Ground Bonding Screw
Figure 16. EPPDMG-6000-3U-3 (L5-30)
32
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
INSTALLATION
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(eight 5-15R)
Output Receptacle (L14-30)
Neutral-to-Ground Bonding Screw
Figure 17. EPPDMG-6000-3U-4 (L14-30)
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
Output Receptacle (L6-30)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(four 5-15R)
Output Receptacle (L14-30)
Neutral-to-Ground Bonding Screw
Figure 18. EPPDMG-6000-3U-5 (L6-30&L14-30)
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
Output Receptacle (L6-30)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(four 5-20R)
Output Receptacle (L6-30)
Neutral-to-Ground Bonding Screw
Figure 19. EPPDMG-6000-3U-6 (L6-30)
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
33
INSTALLATION
PPDM Input Cord (to UPS)
PPDM Output Cord (to UPS)
Output Receptacle (L6-20)
PPDM Output
Circuit Breaker
Input Connector
Output Receptacles
(four 5-20R)
Output Receptacle (L6-20)
Neutral-to-Ground Bonding Screw
PPDM Output Circuit Breakers
Figure 20. EPPDMG-6000-3U-7 (L6-20)
34
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 3
Operation
NOTE Refer to the UPS user's guide for UPS operation.
The PowerPass Distribution Module (PPDM) allows for the removal of
the UPS while providing power to your protected equipment. This
Maintenance Bypass feature is useful when replacing the UPS for
maintenance or upgrades.
Using Maintenance Bypass
To transfer your equipment to Maintenance Bypass (AC Line operation)
and remove the 9135 UPS:
1.
Remove the PPDM front cover.
2.
button on the UPS for approximately three seconds.
Press the
The UPS transfers to Bypass mode and beeps once.
3.
Turn the bypass switch on the PPDM to the BYPASS position. The
PPDM is now powering your equipment from utility power.
4.
If optional Extended Battery Modules (EBMs) are installed, switch
the battery circuit breaker on the first EBM rear panel to the
OFF (O) position.
Unplug the EBM cable and the EBM communication cable from the
UPS.
5.
Disconnect the PDM input and output cords from the UPS (see
Figure 13 on page 29).
6.
Remove the UPS.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
35
OPERATION
To reinstall the UPS and transfer your equipment from Maintenance
Bypass (AC Line operation) to the 9135 UPS:
1.
If optional EBM(s) are installed, reconnect the EBM cable and the
EBM communication cable to the UPS.
Switch the battery circuit breaker on the first EBM rear panel to the
ON ( | ) position.
2.
Plug the input and output cords of the PPDM into the input and
output power connectors on the UPS (see Figure 13 on page 29).
3.
If the PPDM voltage switch is set to 208V, confirm the UPS output
voltage through the front panel (refer to the UPS user's guide).
4.
Turn the bypass switch on the PPDM to the NORMAL position.
5.
button on the UPS until you hear the UPS
Press and hold the
beep (approximately three seconds).
The UPS conducts a self-test and enters Normal mode. The
indicator remains on and the
indicator turns off indicating that
power is available to your equipment.
6.
36
Reinstall the PPDM front cover.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 4
Specifications
Table 4. Model Specifications
Model
Input
Voltage
Input
Current
EPPDMG6000-3U-HW
208/240V
30A
Output Voltage1
Output
Current
115/120V
41A/208V
45A/240V
208/240V
30A
Output Receptacles
Hardwired
EPPDMG-6000-3U-HW
EU
230/240V
30A
115/120/230/240V
30A
Hardwired
EPPDMG-6000-3U-1
(L6-30)
208/240V
24A
115/120/208/240V
30A
(1) L6-30R, (8) 5-15R
EPPDMG-6000-3U-2
(L6-20)
115/120V
20A
208/240V
24A
208/240V
30A
EPPDMG-6000-3U-3
(L5-30)
208/240V
24A
115/120V
41A/208V
45A/240V
EPPDMG-6000-3U-4
(L14-30)
115/120V
208/240V
24A
41A/208V
45A/240V
208/240V
30A
115/120V
41A/208V
45A/240V
208/240V
30A
115/120/208/240V
30A
115/120V
20A
208/240V
30A
EPPDMG-6000-3U-5
(L6-30&L14-30)
208/240V
EPPDMG-6000-3U-6
(L6-30)
208/240V
24A
EPPDMG-6000-3U-2
(L6-20)
208/240V
24A
24A
(1) L6-20R, (8) 5-15R
(1) L5-30R, (8) 5-15R
(1) L14-30R, (8) 5-15R
(1) L6-30R, (1) L14-30R,
(4) 5-15R
(2) L6-30R, (4) 5-20R
(2) L6-20R, (4) 5-20R
1 Output voltage varies ±5% based on the attached load.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
37
SPECIFICATIONS
Table 5. Technical
Frequency
60 Hz
EPPDMG-6000-3U-HWEU: 50/60 Hz
Isolation Transformer
Bypass Switch
Operating Temperature
Storage Temperature
Relative Humidity
Safety Conformance
Agency Markings
EMC (Class A)
Dimensions (WxDxH)
Weight
38
208V/120V or 240V/120V
30A
0°C to 40°C (32°F to 104°F)
-22°C to 55°C (-7°F to 131°F)
5–95% noncondensing
UL 1778; CSA C22.2, No. 107.1, 107.2; NOM-019-SCFI
EN 62040-1-1 (2004-12), EN 62040-2 (2006-6), IEC 60950
cULus, cUL, CE
EN 50091-2, FCC Part 15, ICES-003
442 683 130 mm
17.4” 26.9” 5.1” (3U)
46.7 kg (103 lb)
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 5
PPDM Schematics
This section shows the schematics of each PPDM model.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
39
120V (Isolated)
120V (Isolated)
UPS Output L2,
208-240V
UPS Output L1,
208-240V
Neutral (isolated)
PPDM SCHEMATICS
Figure 21. EPPDMG6000-3U-HW Schematic
40
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
230-240V (Isolated)
115-220V (Isolated)
UPS Output Line 1,
230-240V
UPS Output Line 2
230-240V
Neutral (isolated)
PPDM SCHEMATICS
Figure 22. EPPDMG-6000-3U-HWEU Schematic
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
41
PPDM SCHEMATICS
Figure 23. EPPDMG-6000-3U-1 (L6-30) Schematic
42
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
PPDM SCHEMATICS
Figure 24. EPPDMG-6000-3U-2 (L6-20) Schematic
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
43
PPDM SCHEMATICS
Figure 25. EPPDMG-6000-3U-3 (L5-30) Schematic
44
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
PPDM SCHEMATICS
Figure 26. EPPDMG-6000-3U-4 (L14-30) Schematic
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
45
PPDM SCHEMATICS
Figure 27. EPPDMG-6000-3U-5 (L6-30&L14-30) Schematic
46
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
3
7
E3
6
3 4
30A 8
C1
20
9
CB1
1 2 4
TB3
2
RT1
1
(6)
(7)
(3)
(5)
23 27
P1
(X)
INPUT (Y)
FROM
UTILITY(G)300
L6−30P
E2
E2
J1
(X)
TO POWER(Y)
PROCESSOR
INPUT (G)300
L6−30R
5
(1)
S1
(2) 2
B1
1 1
P22
J22
2 2
1 1
(3)22 P20
4 J20
4
3 3
(2) 21 2 2
(1)
30A
S2
2
1
2
B21
(X1) (X1) 1
0V
0V 190C
(X3) 3
120V
(X2) 2
120V
(H3)
230V
(H2)(X4) 4
208V208V
1
3 14
14
2
4
P3(X5) 5J21P21
(H4)
5
240V240V
10
15
14A
14B
F
CB3
2 1
20A
CB2
2 1
20A
E2
E2
(WHI)
(GRN)
(BLK)
(5−20R)
(WHI)
(GRN)
(BLK)
(5−20R)
1
(WHI)
(GRN)
(BLK)
(5−20R)
(WHI)
(GRN)
(BLK)
(5−20R)
P2
TO POWER(X)
PROCESSOR
OUTPUT (Y)
(G)300
L6−30P
E3
E3
(X)
(Y)
(G)
L6−30R
(X)
(Y)
(G)
L6−30R
PPDM SCHEMATICS
Figure 28. EPPDMG-6000-3U-6 (L6-30) Schematic
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
47
3
7
E3
6
3 4
30A 8
C1
20
9
CB1
1 2 4
TB3
2
RT1
1
(6)
(7)
(3)
(5)
(1)
S1
(2) 2
23 27
P1
(X)
INPUT (Y)
FROM
UTILITY(G)300
L6−30P
E2
E2
J1
(X)
TO POWER(Y)
PROCESSOR
INPUT (G)300
L6−30R
5
1
B1
1 1
P22
J22
2 2
1 1
(3)22 P20
4 J20
4
3 3
(2) 21 2 2
(1)
30A
S2
2
1
2
B21
(X1) (X1) 1
0V
0V 190C
(X3) 3
120V
(X2) 2
120V
(H3)
230V
(H2)(X4) 4
208V208V
1
3 14
14
2
4
P3(X5) 5J21P21
(H4)
5
240V240V
10
15
14A
14B
E1
(WHI)
(GRN)
(BLK)
(5−20R)
CB3
2 1
20A
CB2
2 1
20A
E2
E2
(WHI)
(GRN)
(BLK)
(5−20R)
(WHI)
(GRN)
(BLK)
(5−20R)
48
(WHI)
(GRN)
(BLK)
(5−20R)
P2
TO POWER(X)
PROCESSOR
OUTPUT (Y)
(G)300
L6−30P
CB5
1 2
3 4
20A
CB4
1 2
3 4
20A
E3
E3
J10
(X)
(Y)
(G)
L6−20R
J10
(X)
(Y)
(G)
L6−20R
PPDM SCHEMATICS
Figure 29. EPPDMG-6000-3U-7 (L6-20) Schematic
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
Chapter 6
Service and Support
If you have any questions or problems with the UPS, call your Local
Distributor or the Help Desk at one of the following telephone numbers
and ask for a UPS technical representative.
United States:
Canada:
All other countries:
1-800-356-5737 or 1-919-870-3149
1-800-461-9166 ext 260
Call your local service representative
Please have the following information ready when you call the Help
Desk:
S Model number
S Serial number (located behind the UPS front cover)
S Version number (if available)
S Date of failure or problem
S Symptoms of failure or problem
S Customer return address and contact information
If repair is required, you will be given a Returned Material Authorization
(RMA) Number. This number must appear on the outside of the package
and on the Bill Of Lading (if applicable). Use the original packaging or
request packaging from the Help Desk or distributor. Units damaged in
shipment as a result of improper packaging are not covered under
warranty. A replacement or repair unit will be shipped, freight prepaid for
all warrantied units.
NOTE For critical applications, immediate replacement may be available. Call the Help
Desk for the dealer or distributor nearest you.
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
49
SERVICE AND SUPPORT
50
EATON Two-in-One PPDM (5000/6000 VA) User's Guide S 164201820 Rev 1 www.eaton.com/powerquality
*1642018201*
164201820 1