Download CDA WC140 dishwasher

WC140 Integrated Dishwasher
Manual for Installation, Use and Maintenance
Passionate about style
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu
rtant Important
The
CDA be
Group
cannot be
responsible
injuries
losses caused
incorrect of
usethis
or installation of this
Group Ltd
cannot
heldLtd
responsible
forheld
injuries
or lossesforcaused
byor
incorrect
use or by
installation
Please
note
CDA
reserve the
right
to invalidate
thewith
guarantee
supplied
with thisincorrect
product following incorrect
Please noteproduct.
that CDA
reserve
thethat
right
to invalidate
the
guarantee
supplied
this product
following
installation
or misuse of the appliance.
on or misuse
of the appliance.
This
appliance
is not
to be
used bychildren)
people (including
children)
withsensorial
reducedor
physical,
iance is not
designed
to be
useddesigned
by people
(including
with reduced
physical,
mental sensorial or mental
or who
lack experience
it, unless
they have
had supervision
or instructions
on how to use
or who lackcapacity,
experience
or knowledge
aboutorit,knowledge
unless theyabout
have had
supervision
or instructions
on how
to use
the appliance
by someonefor
who
is responsible
for their safety.
ance by someone
who is responsible
their
safety.
Under
no circumstances
anyremoved
externalfor
covers
be removed
for servicing
or maintenance
circumstances
should
any external should
covers be
servicing
or maintenance
except
by suitably except by suitably
personnel. qualified personnel.
Appliance information:
ce information:
Please
the details
on the
appliance
rating
plate below
forCDA
reference,
to assist
Customer
ter the details
on enter
the appliance
rating
plate
below for
reference,
to assist
Customer
CareCDA
in the
event of Care
a in the event of a
fault with
your
appliance
to register
your appliance
for guarantee purposes.
your appliance
and to
register
your and
appliance
for guarantee
purposes.
ce Model
Appliance Model
umber
Serial Number
Thisdesigned
appliancefor
hasdomestic
been designed
forCommercial
domestic useuse
only.
will invalidate the warranty.
ance has been
use only.
will Commercial
invalidate theuse
warranty
Declarations of Conformity:
rations ofCE
Conformity:
This designed,
appliance has
been designed,
constructed
and marketed
in compliance
with safety
ance has been
constructed
and marketed
in compliance
with safety
requirements
of EECrequirements
Directives of EEC Directives
89/336/EC,
2006/95/EC, IEC436/DIN44990,
EN 50242
EC, 2006/95/EC,
IEC436/DIN44990,
EN 50242
IMPORTANTFOR
INFORMATION
FOR CORRECT
DISPOSAL
OFINTHE
PRODUCT INWITH
ACCORDANCE
WITH EC
ANT INFORMATION
CORRECT DISPOSAL
OF THE
PRODUCT
ACCORDANCE
EC
DIRECTIVE 2002/96/EC.
VE 2002/96/EC.
At thelife,
endthe
of product
its working
life,
product
must be
taken
to a special
authority
waste
collection
d of its working
must
bethe
taken
to a special
local
authority
wastelocal
collection
centre
or to
a dealercentre or to a dealer
appliance recycling services.
appliance providing
recycling services.
Disposing
of
appliance
separately
avoids
possible
negative
for the
environment
Disposing
of aahousehold
household
appliance
separately
avoids
possible
negative
consequences
for
thehealth
environment and health
g of a household
appliance
separately
avoids possible
negative
consequences
forconsequences
the
environment
and
and
health.
It also
enables
thedisposal
constituent
materials
to constituent
betorecovered,
saving
and resources.
a
deriving
from
inappropriate
and enables
the
materials
to beenergy
recovered
to
obtain As
significant
savings
rom inappropriate
disposal
and
enables
the
constituent
materials
be recovered
to both
obtain
significant
savings
reminder
of
need
household
appliances
separately,
the product
is marked
with
a crossed-out
in energy
andthe
resources.
As
a reminder
of the
need
to dispose
of household
appliances
separately,
the product is marked
and resources.
As a reminder
of to
thedispose
need
toofdispose
of household
appliances
separately,
the
product
is marked
with a crossed-out
ossed-out wheeled
dustbin.
wheeled
dustbin. wheeled dustbin.
rtant Important
• Read
prior
toof
installation
and use of the appliance.
the instructions
priorthe
to instructions
installation and
use
the appliance.
• Do
climb on the
open
dishwasher
door to prevent damage.
ot lean or climb
onnot
the lean
openordishwasher
door
to prevent
damage.
• Close
dishwasher
door accidents.
after use to prevent accidents.
the dishwasher
doorthe
after
use to prevent
• Use
detergents,
salt and designed
rinse aid specifically
designed for dishwashers.
nly detergents,
salt only
and rinse
aid specifically
for dishwashers.
• Do
notdishwasher
put solvents
in the dishwasher
detergent
compartment
to prevent risk of explosion
ot put solvents
in the
detergent
compartment
to prevent
risk of explosion
• Only
put dishwasher
safe items into
dishwasher.
If in
doubt,
check with
of the items.
put dishwasher
safe items
into the dishwasher.
If in the
doubt,
check with
the
manufacturer
of the
the manufacturer
items.
• Takethe
care
when loading
the dishwasher
to observe thefor
recommendations
for best
are when loading
dishwasher
to observe
the recommendations
best loading practice,
andloading
also to practice,
ensure and also to ensure
thatassharp
such blade
as knives
aretoplaced
blade
down to prevent accidents.
harp objects such
knivesobjects
are placed
down
prevent
accidents.
Do not open
dishwasher
door iswhen
a programme
is running.
it isthen
necessary
to do so, then open it
ot open the•dishwasher
doorthe
when
a programme
running.
If it is necessary
to doIf so,
open it
slightly to allow
the dishwasher
to pause
programme
andspilling
prevent
anyRemember
water spilling
ightly to allowonly
the dishwasher
to pause
the programme
and the
prevent
any water
out.
thatout.
the Remember that the
water
thevery
dishwasher
very hot when
the programme is running.
in the dishwasher
caninbe
hot whencan
thebeprogramme
is running.
• When
dishwasher
is not inthat
use, you
we reccomend
you
turn off
thesupply
water supply
the supply tap and disconnect
the dishwasher
is notthe
in use,
we reccomend
turn off thethat
water
supply
at the
tap andatdisconnect
the main supply.
ain supply.
you are leaving
dishwasher
for you
an extended
period
should
leave
thetodoor
slightly
are leaving•theIfdishwasher
for anthe
extended
period
should leave
theyou
door
slightly
open
prevent
the open to prevent the
formation
tion of unpleasant
smells.of unpleasant smells.
Recommendations
Recomendations
• To reduce energy and
toto
loading
thethe
dishw•
•
and water
waterconsumption,
consumption,remove
removeallalldirt
dirtresidues
residuesfrom
fromthe
thedishes
dishesprior
prior
loading
dishwasher.
• Only run the
when
loaded.
•
the dishwasher
dishwasheronly
when
fullyfully
loaded.
•
• Place
Place hollow
hollow items
items (bowls,
(bowls,glasses
glassesand
andpans)
pans)face
facedown
downininthe
thebasket.
basket.
Before first use
• Set the water softener level as required by the water hardness in the area.
• Add 2kg of salt into the salt compartment and then fill with water to the top of the salt compartment.
• Remove all the packaging materials from the interior of the dishwasher.
• Fill the rinse aid compartment.
• Run a hot programme without any dishes in the dishwasher.
Control Panel
Power Button
To switch the power to the dishwasher on or off, press the power button (1). When you switch on the dishwasher, the end
of programme light will illuminate.
illumnate.
Programme Selection Button
To select a programme, press the programme selection button (2). The dishwasher will store in its memory the last
programme used. To change the programme, press the programme selection button again until the light next to the
required programme is illuminated.
Delay Timer Button and Delay Timer Indicator Lights
The dishwasher is equipped with a variable delay timer of three, six or nine hours’ duration. To set the delay timer, press the
delay timer button (3). This will switch on the delay timer for three hours, and the 3h light will illuminate. To change the
duration, press the delay timer button again until the light next to the required time (6h or 9h) is illuminated.
To cancel the timer, press the delay timer button again until none of the delay timer indicator lights are illuminated.
As the delay timer counts down, the delay timer indicator lights will illuminate in turn, so at six hours’ delay the 6h light will
illuminate, and at three hours’ delay the 3h light will illuminate.
Salt Warning Light
When the dishwasher salt begins to run out, the salt warning light will illuminate to advise that the salt needs refilling.
Rinse Aid Warning Light
When the rinse aid begins to run out, the rinse aid warning light will illuminate to advise that the salt needs refilling.
End of Programme Light
When the programme is complete, the dishwasher will emit five beeps and the end of programme light will illuminate.
2
Power button
1
3
Programme selection button
Delay timer button
Indicator lights
Starting a programme
• Press the Power button.
• Press the Programme Selection button until the required programme light is illuminated.
• If required, press the Delay Timer button.
• Once the power is switched on, the end of Programme Indicator light will switch on.
• Once a programme is selected, the end of Programme Indicator light will switch off, and the Programme Indicator light will switch on.
• When you close the dishwasher door the programme will start automatically.
Please note: The dishwasher stores the most recently used programme in its memory. To change the
programme, simply press the Programme Selection button .
Programme Selection button
Power button
Delay Timer button
End of Programme
Indicator light
At the end of a programme
If possible, do not open the dishwasher door once the programme has started.
At the end of the programme, the dishwasher will beep five times, and the end of Programme Indicator light will switch on.
Changing a programme
It is possible to change the programme if necessary once the programme has started.
• First open the door slightly to reduce the risk of water spillage.
• Press the Programme Selection button until the required Programme Indicator light is illuminated.
• Then close the door. The dishwasher will begin the new programme from the point at which the old programme stopped.
Cancelling a programme
It is possible to cancel the programme once the programme has started.
• First open the door slightly to reduce the risk of water spillage.
• Press and hold the Programme Selection button for approximately three seconds, until the end of Programme Indicator light flashes and the Programme Indicator light switches off.
• Then close the door. The dishwasher will drain for approximately thirty seconds. Once this is complete, the dishwasher will beep five times and the end of Programme Indicator light will switch on.
Switching the dishwasher off
• Once the dishwasher beeps five times, and the end of Programme Indicator light switches on, the dishwasher can be switched off by pressing the Power button.
• Then turn off the water tap and remove the plug from the power socket.
Please note: The dishwasher will automatically continue on the programme it has started if the door is
opened or in the event of a power cut.
1. Push the latch as shown in figure 1.
2. Add the required amount of detergent. The main detergent
compartment “b” (figure 2) has lines to allow for specific amounts of
detergent. These are marked at either 15 cm3 or 25 cm3, to be
used depending on how dirty the dishes are.
If your dishes are in need of an intensive wash, then add 5 cm3 of
detergent into the prewash section of the compartment “a” (figure 2).
3. Then close the detergent compartment lid until the latch locks.
fig 1
Detergent
Detergent
Please note: You should only use detergents designed specifically for
To in
filldishwashers.
the detergent compartment
use
To fill the detergent compartment
1. Push the latch as shown in figure 1.
1. Push the latch to open the compartment.
Add
the required amount
of detergent.
The main
detergent do not put
If2.using
dishwasher
always
use the detergent
compartment,
2.
Add
the requiredtablets,
amount
of2)
detergent.
The
mainfor
detergent
compartment
compartment
“b”
(figure
has linesorto
allow
specific
amounts
of them
in
the
main
body
of
the
dishwasher
in
the
cutlery
basket.
The solubility
(bdetergent.
in figure 1)These
has lines
allow for
specific15amounts
of detergent.
areto
marked
at either
cm3 or 25
cm3, to be
of dishwasher tablets can vary depending
on
the
temperature
and
duration
of
3, depending on how dirty used are
depending
on
how dirty
the3 or
dishes
are.
theThese
marked
at either
cm
25 cm
programme.
As a result,
it is15recommended
that
powder detergents should
3 of
be used
the
dishes
are.
If your
dishes
are
in
need
of
an
intensive
wash,
then
add
5
cm
in the shorter programmes to allow better performance.
into
prewash
section
of the
compartment
2).
If detergent
your dishes
arethe
in need
of an
intensive
wash,
then add 5“a”
cm3(figure
of
3. Then close the detergent compartment lid until the latch locks.
CDA
detergent
into the
sectiondetergent,
of the compartment
in figure 1).salt
recommends
the prewash
use of separate
rinse aid and(adishwasher
rather
than
combination
tablets
as separateslid
achieve
better
wash
performance.
3.
Then
close
the detergent
compartment
until the
latch
locks.
fig 1
Please note: You should only use detergents designed specifically for
Detergent
fig 2
fig. 1
use in dishwashers.
To fill
thedo
detergent
compartment
If you
use combination
add salt and designed
rinse aid tospecifically
the dishwasher
Please
note:
You shoulddetergents,
only use detergents
for
1. use
Push
the
latch as
figure 1.
and
then
adjust
theshown
water in
hardness
setting and rinse aid setting to the
in
dishwashers.
If using dishwasher
tablets,
always
use the
detergent
compartment,
When you
then use
separate
detergents
again,
you shoulddo
fillnot
theput
2. minimum.
Add
the
amount
of detergent.
The
detergent
them
in required
the main body
of the
dishwasher or
in main
the cutlery
basket. The solubility
salt
and rinse aid“b”
compartments,
adjust
the
waterfor
hardness
setting
to the
compartment
(figure
2)
has
lines
to
allow
specific
amounts
of
of
dishwasher
tablets
can
vary
depending
on
the
temperature
and
duration
of
Ifmaximum
using dishwasher
tablets,
always
use
theadjust
detergent
compartment,
do
not put
and
runAs
an
wash,
then
the
hardness
setting
and
3 orwater
3, to
the programme.
result,
it is
powder
detergents
should
detergent.
These
areaempty
marked
atrecommended
either
15incm
25
cm
be
them
in the
main
body
of
the
dishwasher
or
thethat
cutlery
basket.
The solubility
the
rinse
aid
setting
to
the
appropriate
level.
be
used
in the
shorter
programmes
to allow
better
performance.
used
depending
on can
how
dirty
the dishes
of
dishwasher
tablets
vary
depending
onare.
the
temperature
and duration of
the
programme.
Asina result,
it is
thatthen
powder
detergents
If your
dishes are
need of
anrecommended
intensive wash,
add 5
cm3 of should
Salt
be
usedrecommends
in the
shorter
programmes
to allow
performance.
detergent
into
the the
prewash
ofdetergent,
thebetter
compartment
“a”dishwasher
(figure 2). salt
CDA
use ofsection
separate
rinse aid and
rather
than
combination
tablets
as separatesneeds
better
wash
performance.
ensure
thethe
best
efficiency,
the dishwasher
soft
water.
Hard
water
3. To
Then
close
detergent
compartment
lid achieve
until the
latch
locks.
means
that lime residues
on the
dishes and
theaid
interior
of the
CDA
recommends
the useremain
of separate
detergent,
rinse
and dishwasher
salt
dishwasher,
affecting
performance.
Theadd
softener
system
designed
to
If youthan
do use
combination
detergents,
salt
and
rinseisaid
to the
dishwasher
rather
combination
tablets
as separates
achieve
better
wash
performance.
remove
the
ions
that
make
the
water
hard
to
provide
the
best
quality
wash
Please
note:
You
should
only
use
detergents
designed
specifically
for
and then adjust the water hardness setting and rinse aid setting to the
This is
achieved
byseparate
using dishwasher
useperformance.
in
dishwashers.
minimum.
When
you
then use
detergentssalt.
again, you should fill the
If salt
youand
do use
detergents,
andhardness
rinse aidsetting
to the to
dishwasher
rinsecombination
aid compartments,
adjustadd
thesalt
water
the
maximum
and the
run water
an empty
wash, setting
then adjust
water
hardness
and
then adjust
hardness
and the
rinse
aid setting
to setting
the and
To
add
dishwasher
salt,
follow
the
steps
below:
If using
tablets,
always
use the detergent
do not
thedishwasher
rinse aid setting
the
appropriate
level.
minimum. When
youtothen
use
separate
detergentscompartment,
again, you should
fill put
the
them
therinse
main
body
ofdishwasher
the dishwasher
inwater
the
cutlery
basket.
Thetosolubility
1. inRemove
the
lower
basketor
and
then
unscrew
the
salt
salt
and
aid
compartments,
adjust
the
hardness
setting
the
of dishwasher
tablets
can
vary
depending
and duration
compartment
as
shown
in figure
1. the temperature
maximum
and
runcap,
an empty
wash,
thenon
adjust
the water hardness
settingofand
Salt
thethe
programme.
As a result,
itappropriate
is recommended
that powder detergents should
setting
to thewith
level.
2. rinse
Fill theaid
compartment
dishwasher
salt (do not use table salt), carefully
To
ensure
the
best
efficiency,
the
dishwasher
needs
soft
water.
Hard
water
be usedtoinprevent
the shorter
programmes
to(figure
allow better
performance.
unnecessary
spillage
3). Before
first
use, you
should
means that lime
residues remain
on the dishes
and the
interior
of the
fill
the
compartment
with
2kg
of
dishwasher
salt
and
then
fill
up
the
dishwasher, affecting performance. The softener system is designed to salt
Salt
compartment
with
water
(upwater
to the
brimtoofprovide
the compartment)
as shown
remove
the ionsthe
that
the
hard
theand
best
quality
wash
CDA
usemake
of separate
detergent,
rinse
aid
dishwasher
salt
Torecommends
ensure
the3.best efficiency,
the dishwasher
needs
soft
water.
Hard water
in figure
performance.
This is achieved
by
using dishwasher
salt. wash performance.
rather
than
combination
tablets
as
separates
achieve
better
means that lime residues remain on the dishes and the interior of the
3. Replace the
cap and
the lower basket.
dishwasher,
affecting
performance.
The softener system is designed to
remove
the
ions
that
make
the the
water
hard
toand
provide
best
quality
wash
To
add
dishwasher
salt,
follow
steps
below:
If you do use combination detergents,
add
salt
rinse the
aid to
the
dishwasher
performance.
This
is achieved
using
dishwasher
salt.
1. Remove
the
lower
dishwasher
basket
and
then
unscrew
the saltthe
warning
light
on by
the
control
panel
illuminates,
you
should
andWhen
then
adjust
water
hardness
setting
and
rinse
aid
settingthe
tosalt
the
shown
in figure
refill compartment
theWhen
salt compartment
with
salt
only
–1.do not again,
add water
the salt
minimum.
you cap,
thenasuse
separate
detergents
you to
should
fill the
compartment
aftersalt,
the first
use.adjust
2.add
Fill
theaid
compartment
with
dishwasher
salt (do
not usesetting
table salt),
carefully
saltTo
and
rinse
compartments,
thebelow:
water
hardness
to the
dishwasher
follow
the
steps
to
prevent
unnecessary
spillage
(figure
3).
Before
first
use,
you
should
maximum and run an empty wash, then adjust the water hardness setting and
1. Remove
the lower dishwasher
basket
and then
unscrew
thefillsalt
fill
the
compartment
with
2kg
of
dishwasher
salt
and
then
up
the
theYou
rinseshould
aid setting
the appropriate
level. immediately after adding salt
run ato
prewash
programme
compartment
cap,
shown
into
figure
2. of the compartment) as shown
compartment
withaswater
(up
the brim
dishwasher
salt,
to
prevent
any
damage
to the
figure
3.
2. Fillinthe
compartment
with dishwasher salt (do
notdishwasher
use table salt),systems.
carefully
Salt
3. toReplace
preventthe
unnecessary
spillage.
Before first use, you should fill the cap and the
lower basket.
compartment
with 2kg of
salt
and then
fill up the
saltwater
To ensure
the best efficiency,
thedishwasher
dishwasher
needs
soft water.
Hard
compartment
with water
(up
tothe
thedishes
brim of
the
compartment)
as shown means
thatthe
lime
residues
remain
onthe
and
the
interior of
the
When
salt
warning
light
on
control
panel
illuminates,
you
should
in figure
3.
dishwasher,
performance.
Theonly
softener
system
designed
refill theaffecting
salt compartment
with salt
– do not
add is
water
to thetosalt
3.compartment
Replace
the
capmake
and
remove
the ions
that
thelower
water
hard to provide the best quality wash
after
thethe
first
use. basket.
performance. This is achieved by using dishwasher salt.
When
the saltrun
warning
light onprogramme
the control panel
illuminates,
youadding
should
You should
a prewash
immediately
after
the salt compartment
with
salt damage
only
– doto
not
add
water to the
salt
dishwasher
salt,
prevent
any
the
dishwasher
systems.
To refill
add
dishwasher
salt,to
follow
the steps
below:
compartment after the first use.
1. Remove the lower dishwasher basket and then unscrew the salt
compartment cap, as shown in figure 1.
should
run a programme
immediately
after
dishwasher
2. You
Fill the
compartment
with dishwasher
salt (do not
useadding
table salt),
carefully
salt,
to prevent
any damage
the dishwasher
systems.
to prevent
unnecessary
spillageto
(figure
3). Before first
use, you should
fill the compartment with 2kg of dishwasher salt and then fill up the salt
compartment with water (up to the brim of the compartment) as shown
fig 2
fig.
fig21
SALT
fig 3
SALT
fig 3
3
fig.
SALT
fig 3
SALT
fig 2
Testing strip
The washing effectiveness of your machine depends on the softness of the tap water. For this
reason, your machine is equipped with a system that reduces the hardness in mains water
supply. The washing effectiveness will increase when the system is correctly set. To find out
the water hardness level of water in your area, contact your local water board or determine
water hardness level by using the test strip(if available).
Keep the
Run
Open the adjustment
Softener
Wait for
Make your machine’s water hardness
Shake the
1 min.
setting according to the result
testing strip
testing
water
testing
The efficiency
of
your
dishwasher
depends
on
the
softness
of
the
tap
water.
To
ensure
best efficiency,
thethe
dishwasher
obtained
through
testing strip.
after taking it
strip in
through
strip.
is equipped with a system
thefor
hardness
in the
mains water supply. The efficiency will increase when the
of water.
water
1 out
your that
tap reduces
system is correctly set.
the water hardness level of your water supply you can use the test strip supplied or
forTo
1 find out sec.
alternatively contactmin.
your local water board.
No Lime
Very low lime content
Low lime content
Medium lime content
Lime content
High Lime content
1. Open the testing strip.
Adjusting salt consumption
2. Run water through the tap for one minute.
3. Table
Hold theof
testing
stripHardness
in water for one
second.
Water
Level
Settings
4. Shake the testing strip after taking it out of the water
If the hardness of the water you use is above 90 dF (French hardness) or if you are using well
water; you are recommended to use filter and water refinement devices.
5. Wait for one minute
6. Check the number of marks on the strip to see the level of water hardness.
If the hardness of the water you use is above 60
63dE
dE or
or if you are using well water;
water; you are recommended to use filter and
water refinement devices.
Please note: The level of water hardness is preset to level 3.
1. Press and hold down the programme selection button
2. Press the power button to switch on the dishwasher
3. Keep the programme selection button pressed until the five programme indicator lights and the end of programme
indicator light flash.
4. To adjust the level, press the programme selection button until the required level is selected. The programme lights
will illuminate as in the table of water hardness settings.
Hardness
level
is adjusted
level
3 button.
as a factory setting.
5. NOTE:
To store the
selected water
hardness
level, presstothe
power
9
nse Aid
RinseRinse
Aid Aid
fill the rinse
aid compartment
Rinse
Aid
To fill theTorinse
aidrinse
compartment
fill
the
aidcompartment
compartment
To
fill
the
rinse
aid
Open the rinse aid compartment
by turning and removing the cap as
1.
Open
the
rinse
aid
compartment
by turning
and removing
the cap
1.
Open
the
rinse
aid compartment
by turning
and removing
the as
cap as shown in figure 4.
1. Open the rinse aid compartment by turning and removing the cap as
inshown
shown
figurein4.figure 4.
in figure 4. until the rinse aid indicator goes dark,
Fill the rinse shown
aid compartment
2.
Fill
the
rinse
aid compartment
until
the aid
rinse
aid indicator
dark, 2. Fill the
rinse
aid
compartment
until the
rinse
indicator
goesgoes
dark,
2.
Fill
the
aid compartment
until
the rinse
aid indicator
dark,
as shown in
5rinse
(where
a indicates
the
compartment
is empty,goes
and
figure
as shown
in figure
5 (where “a”
indicates
the compartment
is empty, and as shown
in
figure
(where
a indicates the compartment
is empty, and
shown
in 5
figure
5 (where
“b” indicates
the
compartment
is full).a indicates
as
“b”
indicates
the compartment
is full).the compartment is empty, and
“b” indicates
the compartment
is full).
“b” indicates
the compartment
is full).
3. cap,
Replace
the cap,
theup
capwith
line the
up with the Replace the
ensuring
theensuring
markersthe
onmarkers
the caponline
3. Replace
the cap,the
ensuring
the
markers
on the
cap
up with
thethe
3. Replace
cap,prior
ensuring
the markers
onback
the line
cap
line
up with
compartment
to screwing
the
cap
in place.
compartment prior to screwing the cap back in place.
compartment
prior
to screwing
theback
cap back
in place.
compartment
prior to
screwing
the cap
in place.
fig 4
fig.fig
4 44
fig
Rinse Aid Adjustment
nse Aid
Adjustment
The
level
of
rinseAdjustment
aid use is preset to 4. You can adjust the level of rinse aid
Rinse
Aid
Rinse
Aid
Adjustment
use by
as shown
in You
figure
6. adjust the level of rinse aid
level of rinse
aidadjusting
userinse
is preset
tois4.preset
can
The
use
4. can
Youadjust
can adjust
the level
of rinse
The level
oflevel
rinseofaid
useaid
is preset
to 4. to
You
the level
of rinse
aidaid
by adjusting
as
shown
in
figure
6.
use by adjusting as shown in figure 6.
use by adjusting as shown in figure 6.
If water stains form on the dishes after a wash, the level should be increased.
If blue stains which can be wiped away are left on the dishes after a wah, the
water on
stains
form
on after
the dishes
afterthe
a wash,
levelbe
should
be increased.
ater stainsIflevel
form
the
dishes
a wash,
level the
should
increased.
be decreased.
If water stainsshould
form on
the dishes after a wash, the level should be increased.
If
blue
stains
which
can
be
wiped
away
are
left
on
the
dishes
after
wash, the
ue stains which can be wiped away are left on the dishes after a wash,athe
If blue stains which can be wiped away are left on the dishes after a wash, the
level
should
be
decreased.
l should be
decreased.
Please
note: Rinse aid ensures better quality wash results and
level should
be decreased.
fig.
figfig555
fig 5
increased drying performance.
Please note: Rinse aid ensures better quality wash results and
ase note: Rinse aid ensures better quality wash results and
Please increased
note:
Rinse
aid
quality
results and
drying
performance.
Always
refill
theensures
rinse aidbetter
when the
rinsewash
aid indicator
light on the
reased drying performance.
control
panel
is illuminated.
increased
drying
performance.
Always refill the rinse aid when the rinse aid indicator light on the
ways refillcontrol
the rinse
aid
the rinse aid indicator light on the
panel
is when
illuminated.
Always refill the
rinse
aid when the rinse aid indicator light on the
trol panel is illuminated.
control panel is illuminated.
fig.fig6 6
fig 6
fig 6
Dishwasher Baskets
To adjust the height of the upper basket:
1. Open the basket retaining clips, as shown in figure 7, but turning them to
the side.
2. Remove the upper basket, and relocate the alternate set of wheels on the
runner, as shown in figure 8, pushing the basket back into place.
3. Close the basket retaining clips.
fig 7
The images below are designed as guidance as to best practice for loading
the dishwasher.
Upper basket
fig 8
Lower basket
Bad loads
Standard loading and Test Data
Capacity
• Upper and lower baskets: 12 place settings.
• The upper basket should be adjusted to high position.
• Cups should be placed on to the dish rack pins.
Detergent / Rinse aid
• 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436
(international norms) / Rinse aid dosage adjustment: 4.
Programme test
• Economic 50°C, in accordance with EN 50242 (international norms.).
Programme Listing
Programme
names and
temperatures
Intensive
65°C (P1)
Normal
55°C (P2)
Economic
50°C (P3)
Quick
40°c (P4)
Prewash
No Heat (P5)
Type of
food waste
soups, sauces,
pasta, eggs, pilaf,
potato and oven
dishes, fried foods
soups, sauces,
pasta, eggs, pilaf,
potato and oven
dishes, fried foods
coffee, milk,
tea, cold meats,
vegetables, not
kept for long
coffee, milk,
tea, cold meats,
vegetables, not
kept for long
Pre-wash to
rinse and loosen
residue-awaiting full
load-then select a
programme
Level of soil
high
medium
medium
small
N/A
Detergent
amount
A: 25 cm3/15cm3
B: 5cm3
A+B
A+B
A+B
A
N/A
Prewash
P re
was h
P Prewash
re was h
PPrewash
re was h
P re was h
PPrewash
re was h
5 65
0° Co w
as h
wash
5 0°
as h
55Cowwash
5 50
0° Co wash
w as h
o w as h
540
0° C
wash
5 0° CEnd
w as h
C old
r ins
e
Cold
rinse
C Cold
old r ins
e
rinse
CCold
old r rinse
ins e
CCold
old rrinse
ins e
C old r ins e
rinse
HHot
ot r ins
e
rinse
HHot
ot r ins
e
H ot rrinse
ins e
Hot
Hot
H ot rrinse
ins e
H ot r ins e
Dry
Dry
Dry
Dry
Dry
Dry
Dry
End
Dry
E nd
End
E nd
End
E nd
End
E nd
E nd
Programme
duration (mins.)
110
95
150
30
15
Electricity
consumption
(kW hours)
1,55
1,10
1,05
0,68
0,02
Water
consumption
(liters)
(litres)
17,2
16,5
15,7
12,4
4,5
Warning: Short programmes do not include a drying stage.
The values and times provided above have been obtained under laboratory conditions according to relevant standards.
This information can change depending on the conditions of the dishwasher’s use and environment (network tension,
water pressure, water input temperature and environment temperature).
Unplug
your machine
ime
maythat
accumulate
intemperature,
the machine's
section.InIncase
case
such
gramme
runs at high
andwashing
start the machine.
ofof
insufficiency,
useand turn off its ta
Do not use
hard materials
when cleani
ation;
ecial
cleansing material available in the market. (Cleansing material produced
special
to
and a dampened cloth.
chines
bycompartment
detergent producers.)
etergent
without loading any dishes into the machine,
select a
me that runs at high temperature, and start the machine. In case ofFilters
insufficiency, use
eaning
the
seals inavailable
the machine
eansing
material
in thedoor,
market. (Cleansing material produced
towastes have remain
Check ifspecial
any food
any accumulated
residues in the door seals, wipe the seals regularly
filters. by using a
s clean
by detergent
producers.)
If any food wastes are left, remove the
mpened cloth.
thoroughly under the water tap.
g the seals
inand
the Maintenance
machine door,
Caremachine,
eaning
the
any accumulated
residues in the door seals, wipe the seals regularly by using a
ancloth.
the filters
and spray
arms
at least you
once
a week.
Before beginning
any care
or maintenance,
should
always disconnect the
d
a. Micr
plug your
machine
and
turnsupply,
off its
starting
the cleaning.
appliance
from the
electricity
andtap
alsobefore
turn off the
water supply.
not use hard materials when cleaning your machine. Wipe with a fine cleaning material
gd the
machine,
a dampened
cloth.
e filters Door
andseals
spray arms at least once a week.
our
machine
and turn off its tap before starting the cleaning.
ers
Wipe the dishwasher door seals regularly with a damp cloth to remove
se
hard
materials
when
cleaning
youronmachine.
Wipe
eck if any residues.
food wastes
have
remained
the coarse
andwith
fine a fine cleaning material
mpenedanycloth.
ers.
ny food wastes are left, remove the filters and clean them
roughlyFilters
under the water tap.
b. Coa
c. Meta
To rem
clockw
fig 9
any food wastes have remained on the coarse and fine
You should clean the filters at least once a month.
1. Remove
the lower
basket. the
a. Micro
d wastes
are left,
remove
filters Filter
and clean them
b.
Coarse
Filter
y under2. the
water
tap.
Turn the microfilter anticlockwise and then lift it out as in figure 9.
c. Metal/Plastic Filter
3. Remove the coarse filter from the microfilter (figure 10).
Todishwasher
remove
and clean(figure
the11).
filter
4. Remove the base filtera.
from
the
Micro
Filter compartment
combination, turn it counter
clockwise
and
take
it
out
by
lifting
upwards.1
b. Coarse Filter
fig 10
You should clean and rinse the filters thoroughly before replacing all the
c. toMetal/Plastic
Filter should lock into
sections in reverse order
that above. The microfilter
Pull an
filter. 3
of the
water u
metal/p
filter in
the ma
anothe
metal/p
directio
when t
seen fr
• Never use your dishwasher without
• Incorrect fitting of the filter will reduc
the metal/plastic
To remove
thecoarse
filter combination,
it counter
• turn
Clean
filters are very important in ter
filter. 3 and
Thenclean
pull the
filter out
clockwise
and
take
it
out
by
lifting
upwards.1
of the micro filter.2 Rinse it with lots of
Please note: Never run a programme without the filters in place.
water under the tap. Refit the
Incorrect fitting of the filters may reduce wash performance and
metal/plastic filter. Insert the coarse
potentially damage your
appliance.
Pull
and
the metal/plastic
filter remove
into the micro
filter in a way that
filter.the
3 Then
coarse filter
out
markspull
willthe
correspond
to one
of the
micro filter.2
it with
lots
another.
Attach Rinse
micro filter
into
theof
Spray arms
watermetal/plastic
under the tap.
the to the
filterRefit
and turn
You should clean the spraymetal/plastic
arms direction
at least once aof
month.
arrow
andthe
it iscoarse
locked
filter.
Insert
themicro
arrowfilter
on micro
filter that
can be
filter when
into the
in a way
fig 11
1. Remove the lower basket
seen from
across. 4 to one
the marks
will correspond
place once it is secure as shown
in figure
Pull
and12.remove
2. Pull the lower spray arm upwards to remove it.
another. Attach micro filter into the
Never use
your
dishwasher
without
anyfilter
filter.
3. To
remove
the upper spray
arm, first remove
the nut
on the
upper
metal/plastic
and
turn
tospray
the
ncorrect fitting
of theitfilter
will9.reduce
the
washing
effectiveness.
arm by turning
as indirection
figure
of arrow and it is locked
Clean filters are very important
in terms
themicro
properfilter
running
of the machine.
when the
arrowofon
can be
You should clean and rinse the spray arms thoroughly before replacing
from
4 tightened when
them. Ensure that theseen
upper spray
armacross.
nut is securely
refitting the upper spray arm.
use your dishwasher without any filter.
ct fitting of the filter will reduce the washing effectiveness.
Dishwasher
interior
filters are
very important
in terms of the proper running of the machine.
To deal with an accumulation of dirt, oil or limescale in the dishwasher, run
20 is empty.
an intensive programme with detergent when the dishwasher
Alternatively, there are specialist dishwasher cleaners available that can be used.
fig 12
Failure Codes and Troubleshooting
Your dishwasher control panel is equipped with a diagnostic display to help in the event of a problem with the appliance.
Error Code
Intensive
Normal
Eco
Quick
Prewash
Error description
Inadequate water
supply
Advice
Make sure the water inlet tap is
fully open
Close the water tap, separate the
water inlet hose from the tap and
clean the filter
Restart your machine, contact
CDA service if the error resumes
Continual fill error
Close the tap and contact
CDA service
The waste water in
the machine cannot
be discharged.
Drain hose is blocked
The filters of your machine
might be blocked
Restart the dishwasher and
cancel the programme
If the error continues, contact
CDA service
Heater error
Contact CDA service
Alarm is active against
water overflow
Turn off the dishwasher and
disconnect the water supply
Contact CDA service
Faulty electronic card
Contact CDA service
Overheating error
(temperature in the
machine is too high)
Contact CDA service
Faulty heater sensor
Contact CDA service
Failure Code and Troubleshooting
Problem
The programme will not start
Water remains inside the dishwasher at the end of the
programme
Possible cause
Check the plug, fuse and circuit breakers of the mains supply
The water tap is turned off
The dishwasher door is not fully closed
The water inlet filter or the machine filters are blocked
The water drain hose is blocked or kinked.
knicked
The filters are blocked
The dishwasher stops in the middle of a programme
Power failure
Water inlet failure
Programme is on standby
Wash performance is of a low standard
Poor loading of dishes hinders wash performance.
Insufficient detergent added
Inappropriate wash programme selected
Spray arm blocked
Filters clogged or incorrectly fitted
Water drain pump blocked
White stains on the dishes
Insufficient detergent added
Rinse aid setting is too low
Insufficient dishwasher salt added
Water softener setting is too low
Salt compartment cap not completely closed
The dishes are not completely dry at the end
of the programme
A programme without a drying stage was selected
Rinse aid setting is too low
Dishes unloaded too soon (allow time for drying)
There are rust stains on the dishes
Different sets of cutlery should be kept separate
Too much salt (Water softener setting is too high)
Salt compartment cap not completely closed
Poor appliance earth (check mains electrical supply)
The door is not opening or closing properly
Door tension not correctly adjusted for the décor door
Electrical information
Warning! This appliance must be earthed.
The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug,
follow the steps below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid the risk of
electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or
by the Earth symbol
or coloured GREEN and YELLOW.
• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or
coloured BLACK or BLUE.
• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or
coloured RED or BROWN.
If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the
supply cable, the appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible place.
Installation
• Do not install this appliance if it is damaged in any way. Installing a
damaged appliance may invalidate the warranty.
• The water supply tap should be located in an adjacent cupboard so that it
can be accessed after installation.
• Ensure the appliance is level by adjusting the feet as necessary.
• Only use the water inlet supplied with the appliance.
• If the water pressure is above 10 bar, a pressure relief valve should be used.
• After connecting the water supply, check to ensure there are no leaks.
• The water outlet can either be connected to a water drain or to a sink outlet
spigot. This connection should be at a minimum of 50 cm and a maximum
fig 14
of 110 cm from the floor. The drain hose should be no longer than 4m in
length to ensure good performance from the dishwasher.
fig 15
fig 16
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Passionate about style
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu
CDA Dishwasher – Oversized Fascia Door Mounting Information
Scope of Document:
Where non-standard integrated appliance doors are supplied, additional fitting instructions are required
to ensure compatibility with this product.
Instructions:
The machine is supplied with a fitting template and these instructions should be followed as normal.
However, the fitting template needs to be located lower down the fascia door; this is shown below: -
Offset
Y
Door Height
X
Fitting Template
The amount of offset, Y, depends on the height of the fascia door and can be calculated as: -
WC140:
WC350, WC360:
X-723mm
X-725mm
For example, if you have a 731mm tall fascia door and are fitting a door to a WC140,
then Y = 731 – 723 = 8mm
MT 11/06/09