Download KRAM Ignibox

IGNI-BOX
IGNI-BOX
FOR THE PROFESSIONAL INSTALLER
FOR THE PROFESSIONAL INSTALLER
Technical Specifications
Product Description
IGNIIGNI-BOX and IGNIIGNI-BOX adaptors
Voltage supply range :
Current usage :
10-16 VDC
<1 mA (passive)/2mA-3A (active)
Activation voltage
Active :
Passive :
> +10VDC
< +10VDC
Many new cars do not have an easy accessible switched ignition wire due to the use of Bus based vehicle control networks like CAN-bus. This has spawned the need for a fast
and versatile Ignition substitute.
Maximum current supplied by ignition:
1A. Active when High.
For this reason we have invented the IGNI-BOX. This small
microprocessor controlled unit makes an artificial switched
Ignition based on the noise levels on the constant 12v wire.
To make the needed calculations the IGNI-BOX makes up to
4000 measurements pr. second.
Measurements pr. Second:>3500
Size L x W x H:
75 x 20 x 14 mm
Connector configurations
Input connector
Output connector
+12
NC
1
1
IGN
NC
+12
-
2
3
3
2
NC
-
Made in Denmark by
Kram Telecom A/S
The IGNI-BOX makes the need for an ignition wire, when installing aftermarket car accessories, redundant.
The IGNI-BOX will switch on the ignition signal when the engine is turned on. On some car models it will even turn on
the ignition signal as soon as the key is inserted into the ignition barrel and that way being very similar to the normal ignition functionality in older cars.
A normal IGNI-BOX item number consists of two items. The
1st item is the IGNI-BOX and the 2nd item is the IGNI-BOX
adaptor. The IGNI-BOX adaptor makes the installation plug
and play when installing a Kram Telecom cable set. Some
IGNI-BOX adaptors even exists for OEM Carkit cablesets. But
all the IGNI-BOX really needs in order to make an artificial ignition signal is a connection to the constant 12v and the
ground wire. The installation is that simple.
EN951
IGNI-BOX
IGNI-BOX
FOR THE PROFESSIONAL INSTALLER
FOR THE PROFESSIONAL INSTALLER
69605 (1.G Drive & Talk)
Installation description
IGNI-BOX and IGNI-BOX adaptors.
Needed items:
A. IGNI-BOX.
B. IGNI-BOX adaptor.
B
C
C. Cable set.
B
A
D
D. Carkit-adaptor.
Installation:
Installation steps 1 to 7 must be followed as described to ensure correct function of
the IGNI-BOX.
Cableset ready for step 3.
1.
Connect the IGNI-BOX adaptor B between the connectors supplying the
Carkit C & D. See pictures below for specific info regarding the different
adaptor types.
2.
Connect the IGNI-BOX A to the 8 pin output connector.
connector
3.
Start the engine and let it run for approximately 15 sec.
4.
Stop the engine, remove the key and wait approximately 10 sec.
Cableset ready for step 3.
5.
Connect the IGNI-BOX to the 6 pin Input connector.
connector See the arrow on pic
tures below. When the IGNI-BOX is connected the ignition goes on (Ignition
wire goes high) and the carkit should start-up.
69610 (Express mutecables used with THB / V2-FLEX / Smarteq)
6.
7.
Please wait while the IGNI-BOX programs itself. When the programming
phase is complete, after approximately 20 sec, the ignition will go off
(Ignition wire goes low) and the carkit should shut down.
NOTE: Please avoid interfering with the cars wiring loom or electronics
while the IGNI-BOX is programming itself.
Please make a function check. The blue ignition wire in the 8 pin output
connector should source 12v within 5-30 sec. after the engine is started,
and should source 0v 5-30 sec after the engine is turned off. In some car
models the IGNI-BOX will also be able to source 12v if the key is in the igni
tion but the engine is off. NOTE: If the IGNI-BOX does not work as described
please disconnect the 6 pin input connector and repeat installation from
point 3.
Note: If the car is equipped with accessories like “Follow me home light” or other
systems that might be active when the car is parked. Please make sure these systems are active when installing the IGNI-BOX.
69610 (Express mutecables used with FWD / ALAC)
C
B
A
B
D
C
A
Cableset ready for step 3.
69615 (ISO2CAR / Parrot cableset / ISO radio)
C
A
D
B
D
Cableset ready for step 3.
See our complete Radio Mute program on our website
www.kram.dk