Download StarTech.com R300WN22MO5G WLAN access point

Metal IP67 Outdoor Wireless-N Access
Point - 300Mbps
R300WN22MOD / R300WN22ODG / R300WN22ODE /
R300WN22MOD5 / R300WN22MO5G / R300WN22MO5E
*actual product may vary from photos
DE: Bedienungsanleitung - de.startech.com
FR: Guide de l'utilisateur - fr.startech.com
ES: Guía del usuario - es.startech.com
IT: Guida per l'uso - it.startech.com
NL: Gebruiksaanwijzing - nl.startech.com
PT: Guia do usuário - pt.startech.com
For the most up-to-date information, please visit: www.startech.com
Manual Revision: 10/24/2014
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by StarTech.com could void the user’s
authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la
classe [B] est conforme à la norme NMB-003 du Canada.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not cause interference, and (2)
This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an
uncontrolled environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator and your body.
Instruction Manual
Déclaration d’exposition à la radiation:
Cet équipement respecte les limites d’exposition aux rayonnements IC définies pour un
environnement non contrôlé. Cet équipement doit être installé et mis en marche à une
distance minimale de 20 cm qui sépare l’élément rayonnant de votre corps.L’émetteur ne doit
ni être utilisé avec une autre antenne ou un autre émetteur ni se trouver à leur proximité.
FCC ID: SCDOW141000001
IC: 11232A-R300WN22MOD
FCC ID: SCDOW161000001
IC: 11232A-300WN22MOD5
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other
protected names and/or symbols of third-party companies not related in any way to
StarTech.com. Where they occur these references are for illustrative purposes only and do not
represent an endorsement of a product or service by StarTech.com, or an endorsement of the
product(s) to which this manual applies by the third-party company in question. Regardless
of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby
acknowledges that all trademarks, registered trademarks, service marks, and other protected
names and/or symbols contained in this manual and related documents are the property of
their respective holders.
Important Notice
This product MUST be installed by a professional installer who is familiar with local building
and safety regulations, where appropriate, and is licensed by applicable authorities. The
professional installer is responsible for making sure grounding is available and that it meets
the relevant local and national electrical codes. Failure to employ a professional installer may
render the product warranty void and it may also expose the end user or service provider to
legal and financial liabilities. StarTech.com expressly disclaims any and all liabilities for injury,
damage, or violation of regulations due to improper installation of outdoor units or antennas.
Always remember to protect the AP by installing grounding lines as it is necessary to protect
your outdoor installations from lightning strikes and the build-up of static electricity. The AP
must be grounded properly before powering up, as direct grounding of an outdoor AP is
critical and must be done correctly to protect your networks from harsh outdoor environments
and destructive ESD surge.
CAUTION: Be sure that earth grounding is available and that it meets local and national
electrical codes. If in doubt always consult with a qualified electrician to make sure the outdoor
installation is properly grounded. For additional lightning protection, lightning rods, lightning
arrestors or RJ45 surge protectors may be used to compliment the installation.
Instruction Manual
i
Instruction Manual
ii
Table of Contents
Introduction.............................................................................................1
Packaging Contents.................................................................................................................................. 1
System Requirements............................................................................................................................... 1
Product Diagram.....................................................................................1
Front View..................................................................................................................................................... 1
LED Indicators..........................................................................................2
Installation...............................................................................................2
Preparing Your Site.................................................................................................................................... 2
Hardware Installation............................................................................................................................... 3
Operation.................................................................................................4
Default Settings.......................................................................................................................................... 4
AP Mode Setup........................................................................................................................................... 5
Technical Support...................................................................................8
Warranty Information.............................................................................8
Instruction Manual
iii
Introduction
Packaging Contents
• 1 x Outdoor Wireless Access Point
• 1 x PoE Injector
• 1 x Pole Mounting Kit
• 1 x Quick Start Guide
System Requirements
• A networked computer system with a Java-enabled web browser (for configuration)
• Cat 5 (or better) network cabling from PoE Injector to Wireless AP and PoE Injector
to LAN Switch/router (no more than 100m total)
Product Diagram
Front View
LED Indicators
LAN Port
(Secondary)
PoE Port
Ground Wire Connector /
Reset Buton (remove screw)
Cable Grommets
Instruction Manual
1
LED Indicators
1
Wireless Signal
Strengths LEDs
Shows different signal strength levels. (Only supported in WDS,
Client Bridge + Repeater AP, CPE + Repeater AP Mode)
2
Power LED
A solid green light indicates the device is powered and ready.
3
LAN LED
A solid green light indicates the LAN port connection is OK. A
blinking green light indicates that the unit is transmitting data
over that port.
4
LAN LED (PoE)
A solid green light indicates the LAN port (PoE) connection is OK.
A blinking green light indicates that the unit is transmitting data
over that port
Installation
Preparing Your Site
1. Determine the location for the included PoE injector and mount using the
appropriate screws/anchors for the material you are mounting to (not included).
2. Determine the location for the Wireless AP. If you are pole-mounting the AP, use
the included Pole Mounting Kit to secure the device. If you are wall mounting the
AP, use the appropriate screws/anchors for the material you are mounting to (not
included).
3. Prepare/purchase the required length of Ethernet cabling to go from the PoE
Injector to your LAN Switch or router, and from PoE Injector to the AP. The total
length of Ethernet cabling from the Wireless AP to your LAN switch or router should
not exceed 100m.
Note: Molded / Snagless Ethernet cables are not advised for this product, as the added
bulk on the connector end makes it difficult to fit within the included Cable Grommets.
Instruction Manual
2
Hardware Installation
1. Connect the included power adapter to an available wall outlet and the DC jack to
the PoE injector.
2. Connect an Ethernet cable from the LAN port of the PoE Injector to your LAN switch
or router.
3. Connect a second, longer Ethernet cable from the PoE port of the PoE Injector. The
other end of this cable will connect to the AP as instructed in the following steps.
4. Unscrew the Cap portion of the Cable Grommet and remove the Collar.
Collar
Cap
5. Slide the Cap onto the cable first, then split the Collar and wrap it around the cable.
6. Connect the cable to the PoE port on the AP, then slide the Collar into the Grommet.
7. Thread the Cap over the assembly.
Note: The AP may take up to 2 mins to complete the power on sequence.
8. Connect an Ethernet cable from the LAN port of the PoE Injector to your LAN switch
or router.
Instruction Manual
3
Operation
For complete operating instructions / specifications, please visit www.startech.com/
R300WN22MOD
Default Settings
Default IP Address: 192.168.2.254
Username / Password: root / default
1. Configure a system to be on the same subnet as the AP (e.g. 192.168.2.2 – 253).
2. Open your preferred web browser and enter the IP address 192.168.2.254 into the
address bar, then press Enter.
3. Enter your Username / Password to login to the web interface (Default: root /
default).
4. From the menu at the top, select System -> Operating Mode, to select your preferred
mode from the available options, then click Save & Reboot.
Router AP Mode
(R300WN22MOD /
ODx only)
In Router AP Mode, 802.11n/g/b compliant devices can connect to
the wireless network, with NAT to bridge LAN / WAN connections.
AP Mode
In access point (AP) mode, 802.11n/g/b compliant devices can
connect to the wireless network.
WDS Mode
Wireless distribution system (WDS) mode expands current wireless
coverage from other Wireless AP devices that are in WDS mode.
Client Bridge +
Repeater AP Mode
WISP Client Bridge + Repeater mode acts as a bridge between two
LAN segments over a wireless link, extending network coverage.
CPE + Repeater AP
Mode
WISP CPE + Repeater mode acts as a bridge between two LAN
segments over a wireless link, extending network coverage, with
NAT to bridge LAN / WAN connections
Instruction Manual
4
5. Once the AP reboots into your desired mode, re-connect to the web interface.
6. Select System -> Setup Wizard to go through the basic configuration for that mode.
Available screens and settings will vary, depending on the mode selected.
AP Mode Setup
LAN Setup – Configure your desired IP Address settings for the LAN interface of the AP,
then click Next.
Note: If you change the default IP address, use the new address to connect to the web
interface going forward.
DNS – Configure a primary and secondary DNS server, if desired, then click Next.
Instruction Manual
5
Wireless Setup – Configure your desired wireless settings including SSID, wireless
mode and transmit power, then click Next.
Wireless Security Setup – Select your desired wireless security type and configure a
key, then click Finish to apply your settings and restart the AP.
Note: It is strongly recommended to configure security, to avoid unwanted access to
your wireless network.
To restrict access to the web interface of your AP, it is also recommended to configure
a password, which can be done by selecting System -> Management from the menu.
Click Save to apply the changes.
Note: The root account allows read / write access to the AP interface, while the admin
account allows read only.
Instruction Manual
6
Instruction Manual
7
Instruction Manual
8
Technical Support
StarTech.com’s lifetime technical support is an integral part of our commitment to
provide industry-leading solutions. If you ever need help with your product, visit
www.startech.com/support and access our comprehensive selection of online tools,
documentation, and downloads.
For the latest drivers/software, please visit www.startech.com/downloads
Warranty Information
This product is backed by a two year warranty.
In addition, StarTech.com warrants its products against defects in materials
and workmanship for the periods noted, following the initial date of purchase.
During this period, the products may be returned for repair, or replacement with
equivalent products at our discretion. The warranty covers parts and labor costs only.
StarTech.com does not warrant its products from defects or damages arising from
misuse, abuse, alteration, or normal wear and tear.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their
officers, directors, employees or agents) for any damages (whether direct or indirect,
special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business,
or any pecuniary loss, arising out of or related to the use of the product exceed the
actual price paid for the product. Some states do not allow the exclusion or limitation
of incidental or consequential damages. If such laws apply, the limitations or exclusions
contained in this statement may not apply to you.
Instruction Manual
9
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise.
StarTech.com is your one-stop source for every connectivity part you need. From
the latest technology to legacy products — and all the parts that bridge the old and
new — we can help you find the parts that connect your solutions.
We make it easy to locate the parts, and we quickly deliver them wherever they need
to go. Just talk to one of our tech advisors or visit our website. You’ll be connected to
the products you need in no time.
Visit www.startech.com for complete information on all StarTech.com products and
to access exclusive resources and time-saving tools.
StarTech.com is an ISO 9001 Registered manufacturer of connectivity and technology
parts. StarTech.com was founded in 1985 and has operations in the United States,
Canada, the United Kingdom and Taiwan servicing a worldwide market.