Download Fantom Drives 2TB Professional

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
QuickStart
Installation Guide
Fantom Drives
20525 Manhattan Placenue
Torrance, CA 90501
Sales: 310-320-7272
Support: http://www.FantomDrives.com/helpdesk
www.FantomDrives.com
By MicroNet
FCC Compliance Statements
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate
frequency energy and, if not installed and used in accordance with the instructions, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to equipment off and on, the user is encouraged to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
01-14-2013
MAN-GFQ3 Rev 2
The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation
of this document to assure its accuracy, Fantom Drives and Fantom Drives assume no liability resulting from errors or omissions in this document, or from
the use of the information contained herein.
Fantom Drives reserves the right to make changes in the product design without reservation and without notification to its users.
Fantom Drives, The Fantom Drives Logo, Fantom Drives and the Fantom Drives logo are registered trademarks of Fantom Drives Technology. FireWire,
the FireWire logo, Macintosh, and the MacOS Logo are trademarks of Apple Computer Inc. Microsoft Windows, the Windows Logo, and Windows Vista
are registered trademarks of Microsoft Corporation. All other names and logos are property of their respective owners.
Copyright © 1999, 2013 Fantom Drives Technology. All rights reserved. This publication may not be reproduced, stored in a retrieval system, or transmitted in any form or by any means, in whole or in part, without the prior written consent of Fantom Drives, 20525 Manhattan Place., Torrance CA 90501.
Thank you for choosing Fantom Drives! Your Fantom Drives
G-Force Megadisk has been built to the highest standard of quality
and workmanship and, when used according to the instructions
in this guide, will provide years of trouble-free operation. We at
Fantom Drives take great pride in bringing personal satisfaction to
each of our customers.
Your Fantom Drives' disk drive is compatible with all USB-capable
Apple Macintosh computers running Apple® Mac® OS 10.5
(or greater) and PC-Compatible computers running Microsoft®
Windows ® Vista, Seven, 8, and Windows Server® 2003/2008.
Contents
to returning the Product to Fantom Drives. Fantom Drives is not liable
for any loss or damage to these items.
Introduction............................................................. 3
This limited warranty does not cover: (1) any consumables (such as
batteries) supplied with this product; cosmetic damages; damage or
loss to any software programs, data or removable storage media; or
damage due to the Product such as but not limited to excessive heat
or humidity, or modifications of this Product; (2) improper installation,
operation, testing or maintenance of this Product; (3) power failure or
connection to improper voltage supply; or; (4) attempted repair by any
party other than Fantom Drives. This Warranty does not apply when
the malfunction results from the use of this Product in conjunction with
accessories, products or ancillary or peripheral equipment, or where it
is determined by Fantom Drives that there is no fault with this Product
itself.
This Limited Warranty is invalid if the factory applied serial number has
been altered or removed from the Product.
Parts & Accessories List........................................... 4
System Requirements .............................................. 5
FireWire and USB 2.0 Compared.............................. 6
Fantom Drives External Hard Drive at a Glance........... 7
Precautions............................................................. 8
Connecting the Drive to Your Computer...................... 9
Formatting Your Fantom Drives External Hard Drive.. 10
Formatting the Drive in Mac OS X ............................. 10
Formatting the Drive in Windows .............................. 11
How to safely dismount and turn off your
Fantom Drives External Hard Drive.......................... 12
Troubleshooting /
Frequently Asked Questions (FAQ) ......................... 13
Warranty ............................................................. 18
Contact Information............................................... BC
Repair or replacement as provided under this warranty is the exclusive
remedy of the consumer. Fantom Drives shall not be liable for any
incidental or consequential damages for breach of any express or
implied warranty, breach of contract, negligence, strict liability or any
other legal theory related to this product. Such damage include, but are
not limited to, loss of profits, loss of data, loss of use of the product
or any associated equipment, down time and purchaser’s time. Except
to the extend prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose on this product is
limited in duration of this warranty.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or allow limitations on how long on implied
warranty lasts, so the above limitation or exclusions may not apply to
you. This warranty gives you specific rights; you may have other rights
which vary from state to state.
18
3
One Year
Limited Warranty
Fantom Drives warrants this product (the “Product”) against defects in
material or workmanship as follows:
1. LABOR: For a period of one (1) year from the original date of
purchase from Fantom Drives or its authorized relseller, Fantom Drives
will repair defective Product (or, at its option, replace with a new or
recertified product) at no charge. After this 1 year period, you must
pay for all labor charges.
2. PARTS: For a period of one (1) year from the original date of purchase
from Fantom Drives or its authorized reseller, Fantom Drives will supply,
at no charge, new or rebuilt replacement parts in exchange for defective
parts of this Product. Any replacement parts will be warranted for
the remainder of the original warranty period or ninety (90) days from
installation by Fantom Drives. All exchanged parts replaced under this
warranty will become the property of Fantom Drives.
This warranty only covers the hardware components packaged with the
Product. This warranty does not cover any software contained in, or
included with, the Product; any such software is provided “AS IS”. Please
refer to any documentation included with the software for your rights
and obligations with respect to the software.
This warranty extends only to you, the original purchaser. It is not
transferable to any one who subsequently purchases the Product from you.
Proof of purchase in the form of a bill of sale (which is evidence that
the Product is within the warranty period) must be presented to obtain
warranty service.
To obtain warranty service you must take the Product, or deliver the
Product freight prepaid, in either it’s original packaging, or in a package
that provides the Product with a degree of protection equivalent to
that of the original packaging, to Fantom Drives. Items shipped with
insufficient packaging will void the item's warranty, and may be rejected
for service.
Fantom Drives is not responsible for any damage to, or loss of, any
programs, data, or other information stored on any media or any part
of any Product serviced hereunder. Be sure to remove all features,
parts, options, alterations, and attachments not under warranty prior
Introduction
Welcome, and thank you for purchasing G-Force Quad
Interface Hard Disk from Fantom Drives.
In photos and illustrations in this guide, The following alert
symbols are used in this guide:
This signifies important
information for ALL users.
This signifies important information for USB 2.0 users.
This signifies important information for eSATA users.
This signifies important information for FireWire users.
The G-Force Quad Hard Disk can only sustain one connection
type at any given time; the drive will appear as an eSATA
device when connected via eSATA, a FireWire device when
connected via FireWire, and as a USB device if the USB
cable is connected.
USB 3.0 compatibility with USB 2.0
USB 3.0 ports are backward compatible with USB 2.0 and
USB 1.1. However, if you connect the drive to an earlier USB
standard port, it will operate at that port's specified speed.
System Requirements
• G5/Intel or newer Mac running Mac OS X 10.5 or newer
• 1.8 GHz Pentium 4 class PC or faster CPU running
Windows® Vista® or newer
• An available eSATA Port or
• An available USB 2.0 or 3.0 port or
• An available FireWire 400 port or
• An available FireWire 800 port
4
17
Parts &
Accessories List
The package contains the following items:
•
•
•
•
•
Fantom Drives G-Force Quad Hard Disk
Quick Start Installation Guide
FireWire 400 cable
• FireWire 800 cable
eSATA cable
• USB cable
Disk Stand
• AC Adapter
If you are missing any items listed above, please fill out the
customer support form at:
http://www.fantomdrives.com/helpdesk
Please retain a copy of your receipt. You will need it if
warranty repair service is required in the future.
Q: I do not see my drive listed in the My Computer window,
but it does appear in the Device Manager list.
A: Right-click on My Computer. Select Manage in the pop-up
menu. In the Computer Management window and navigate
to Storage -> Disk Management. In the Disk Management
window, you should see a list of available storage devices.
Look for the disk that has a capacity closest to your Fantom
Drives unit, and right-click on the corrolating right-hand box.
In the pop-up menu that appears select "Delete Partition."
The description will change to say “Online" & "Unallocated”.
Right-click on the box and select Create New Partition in the
pop-up menu. When the Partition Wizard appears, select
"Primary Partition" and click "Next." Click "Next" in the next
dialog, selecting the default value for the drive. You will then
see a drive letter (you can change this drive letter if you
wish); click "Next." You will then be asked to format the drive.
Q: After I connected the drive to my PC, I got the following
alert message: HI-SPEED USB Device Plugged into non-HISPEED USB Hub.” What does this mean?
A: This alert message will appear if you plugged the drive into
a USB port that only supports USB 1.1 or 2.0. This is fine,
except your drive will operate at the nominal host connection
speed instead of USB 3.0.
If an issue cannot be resolved by using our FAQ, please
contact Technical Support via the Fantom Drives support
site at http://www.Fantomdrives.com/helpdesk
16
5
Q: I have a FAT32 disk, and when I try to copy a large file I
get an error saying there is not enough room on the drive-- I
have lots of free space!
A: FAT32 only allows files up to 4GB in size. To copy larger files,
please reformat the volume using MacOS Extended Format.
FAQs for PC Users:
Precautions
Failure to follow the precautions described below may cause
damage to your Fantom Drives External Hard Drive and void
the warranty.
• DO NOT open the case. Doing so will void the warranty.
Q: My computer does not recognize the drive.
A: Make sure all of your connections are secure. If you have an
add-on card, make sure it is working properly and/or update the
driver. Also, make sure you have all the latest updates for your
Windows installation
• DO NOT use a third-party AC adapter or power cord. Doing
so may damage the Drive and void the warranty.
Q: I formatted my hard disk under Windows XP, but my Vista
machine does not allow me to delete or modify files on the drive.
A: Windows Vista and XP handle file permissions differently. In
Windows XP the default user group has full permissions to every
volume, whereas in Vista they do not. To fix this condition, you
need to grant the users group modify privileges to the drive:
• DO NOT disconnect any cables while the Drive is powered
on without first properly dismounting the device via your
operating system; doing so can result in data loss and
possible damage.
1.Right-click the drive letter in Explorer and select properties
2.Click the security tab
3.Click "Edit." You will be asked to enter your administrator password.
4.Select "Users" and check the Modify box
5.Click OK.
Q: Where are the drivers for my operating system?
A: Windows 2000 and newer already include all the necessary
drivers. There are no drivers available for Windows NT or 98.
Q: When I leave my computer idle for a while, my drive won’t
work properly.
A: The most likely cause is that your computer is going into
sleep mode. The immediate solution is to shut down your computer
and turn off the drive, and then restart your computer. Once your
computer is completely booted up, turn on the drive. You should
see the drive in the Windows Explorer. To prevent this problem from
recurring, open the “Power Settings/Energy Saver” and set it to
never go into sleep mode.
• DO NOT bump, jar or drop the Drive as this may damage
it or result in loss of data.
• DO NOT set any liquids or beverages on the Drive as they
may damage the internal electronics.
• Fantom Drives highly recommends that you regularly backup the files stored on your Fantom Drives External Hard
Drive. Fantom Drives is not responsible for any data loss, nor
will Fantom Drives perform any recovery on lost data or files.
6
15
FireWire & USB 2.0
Compared
Data transfer rate of 400 Mbps
FireWire is suitable for applications
where delayed or out-of-order data
frames are unacceptable, such as digital
video editing.
Data transfer rates up to 480 Mbps
With USB, data transfer rates can
vary depending on a number of factors,
including available CPU resources.
Supports up to 63 devices
FireWire devices can be linked in a daisychain configuration. With the use of
FireWire hubs, up to 63 devices can be
linked on a single FireWire bus.
Supports up to 127 devices
Connecting more than one or two USB
devices to a computer typically requires
the use of one or more hubs: each hub
can accommodate several USB devices.
Peer-to-peer architecture
FireWire devices are intelligent. Data
transmission can take place without the
need for input from the computer.
Master-slave architecture
The computer dictates data flow to,
from, and between attached devices.
Cable length up to 14ft
Cable length up to 16.5ft
On-bus power up to 45 W
FireWire can power larger, higher power
consumption devices than USB 2.0.
On-bus power up to 2.5 W
Suitable for low-power-consumption
devices such as flash card readers.
Plug & Play
You do not need to install drivers,
assign unique ID numbers, or connect
terminators.
Plug & Play
You do not need to assign unique ID
numbers, or connect terminators. On
most operating system you do not need
to install drivers.
Hot-swappable
Devices can be added and removed
while the computer is running. Also, you
can turn off the device when not needed,
in order to conserve electricity.
Hot-swappable
Devices can be added and removed
while the computer is running. Also, you
can turn off the device when not needed,
in order to conserve electricity.
Q: I'm having trouble seeing my disk when connected via eSATA
A: eSATA host connections require the SATA host bus to support
and have AHCI mode enabled and active. Additionally, the eSATA
cable must be a proper shielded cable, 1M or less in length, with
a blade depth (the recessed plug of the cable) of 1cm.
Some host bus adapters have built-in RAID functionality and must
be configured before the disks will appear to the host computer.
For these cases, the eSATA controller will have either a BIOS
utility or a software RAID configuration utility that will need to
be configured prior to use. Please consult your eSATA host bus
adapter documentation for more information.
FAQs for Mac Users:
Q: Why is my drive asking me to format it? It was already
formatted and it contains data.
A1:Run a disk repair utility on the drive.
A2:Perform permission repair on your system drive. Open the
disk utility (located in /Applications/Utilities/Disk Utility.app.)
Select your system drive (usually the first disk listed) and click
"Repair Disk Permissions" in the "First Aid" Tab.
A3:Restart your computer. As soon as the bootup chime sounds,
press and hold down the option-command-p-r key combination
to reset the PRAM. Release the keys when the chime sounds
a second time. Please refer to your Mac manual for more
information on these procedures
Q: My computer does not recognize the drive.
A: Check to make sure that all of your connections are secure
and that the power switch is in the "ON" position. Then check if
your External Hard drive is listed in the Apple System Profiler. If the
problem persists, verify that the appropriate port used is functioning.
Q: I'm trying to copy files to/from FAT32 volumes or network
shares, and it keeps failing.
A: FAT32, HFS+, and other file system formats allow different
standards of filename length or use of special characters.
Rename the offending file(s) and try the operation again.
14
7
Q: Can I leave my G-Force Megadisk Black on all the time, or
should I turn it off when not in use?
A: The G-Force Megadisk Black is meant to be left on, but does not
add any limitations on being turned off. Drive reliability is affected
by repeated power cycles, and the G-Force Megadisk Black
cannot alleviate this. In addition, Micronet recommends that
the drive’s power supply is connected through a UPS or surge
protector; In the case of a power surge, or brown/black out, the
hard drive’s sensitive electrical components will not be damaged.
Fantom Drives G-Force
Black Quad Hard Disk
at a Glance
Disk Activity/Power
Indicator Light
Q: Is my drive compatible with my DVR?
A: All MicroNet / Fantom Drives products are compatible with
DVRs capable of addressing external disks over their respective
interface. For example, our G-Force eSATA+USB external disks
are compatible with DVRs capable of addressing eSATA or USB
external disks. That said, our products are explicitly supported
for use with Windows PCs and Apple Macintosh computers.
We can provide support for use under those platforms- we do
not have the equipment, training, or authorization from other
equipment vendors such as DVRs to support their platforms.
While many DVRs have the ports, the individual provider firmware
may or may not allow access to an external device; if you received
your DVR from your cable or satellite vendor, consult with their
customer support about whether the USB/eSATA ports are
active, or if there is a firmware update required. Alternatively,
consult the manufacturer of the DVR regarding this feature.
Q: How can I test my disk to make sure it is not defective?
A: Modern disks drives have a diagnostic on board processor
that monitors the disk during operation and records various
diagnostic values including any detected failures. This diagostic
method, S.M.A.R.T. (Self-Monitoring, Analysis and Reporting
Technology) is a monitoring system for computer hard disk
drives to detect and report on various indicators of reliability, in
the hope of anticipating failures. SMART data can be accessed
and used for active testing using a SMART diagnostic program.
There are numerous SMART monitoring tools available- we
recommend the following:
Smartmontools- http://smartmontools.sourceforge.net/
HDDScan (Windows) http://hddscan.com/
SMARTreporter (Mac)* http://www.corecode.at/smartreporter
For more information about SMART and its values, please see
http://en.wikipedia.org/wiki/S.M.A.R.T.
Power Switch
AC adapter port
USB 3.0 port
eSATA port
FireWire 800 ports
FireWire 400 port
8
13
Connecting the Drive
to Your Computer
1. Plug the AC adapter cord into the power port on the back of
the Drive. The plug should not require much effort to insert. Plug
the other end of the power cord into a wall receptacle.
2. Connect the appropriate cable to your host:
USB, eSATA, and FireWire plugs are shaped so they can only be
properly inserted one way. Be sure to insert the plugs properly or
you may damage the drive and void the warranty.
(USB) Connect the square USB 3.0 connector (type B) of the
included USB cable to a the square USB plug on the G-Force
Black, and the rectangular end to a free USB port on your
computer.
(eSATA) Connect the included eSATA cable to a free eSATA port
on your computer.
If your computer does not have USB 3.0 ports and/or
eSATA ports, you may purchase an expansion card for your
computer. Contact your authorized Fantom Drives reseller
for further details.
(FireWire) Connect the included FireWire cable to a free
FireWire port on your computer. The G-Force Black Quad Hard
Disk has two FireWire 800 ports and one FireWire 400 port for
connecting additional FireWire device in a daisy chain.
4. Press the power switch located on the back of the G-Force Black
Hard Disk. Once the Drive is powered up, your computer should
recognize it and the Drive will be ready to use.
Troubleshooting/
Frequently Asked
Questions (FAQs)
General Questions
Q: I bought a 500GB drive, but my computer is showing
465GB. Where is the missing capacity?
A: Hard drive manufacturers market drives in terms of decimal
(base 10) capacity. In decimal notation, one megabyte (MB) is
equal to 1,000,000 bytes, and one Gigabyte (GB) is equal to
1,000,000,000 bytes. Many operating systems use the binary
(base 2) numbering system to describe disk capacity; In the
binary numbering system, one megabyte is equal to 1,048,576
bytes, and one gigabyte is equal to 1,073,741,824 bytes.
Simply put, decimal and binary translates to the same amount
of storage capacity.
Q: Is my external hard drive bootable?
A: Yes! As long as your host hardware and operating system
support booting from eSATA or USB. Refer to your computer’s
documentation for more information
Q: My drive was working fine yesterday but now its gone!
A: The disk may have been shut down without being dismounted,
or may have failed. If you do not hear and feel the drive spin up
when you connect the power, the drive will need to be replaced.
If you verify that the computer input and the drive data cable are
working, you may be able to repair or recover the data with your
computer’s disk repair utility or a third party utility.
If your disk repair utility cannot repair or see the disk, the
drive has failed and will need to be replaced. If data recovery
is desired, please contact an established professional data
recovery firm. For a checklist of what qualities you might seek,
see www.drivesavers.com/why_drivesavers/index.html or www.
ontrack.com/services.
12
9
How to Safely Dismount
and Turn Off Your G-Force
Megadisk
When a device such as a hard drive is mounted, the computer
‘sees’ the device and is able to communicate with it. When you
dismount a device, the computer will commit any outstanding
I/O and no longer recognizes the disk, preparing the disk to be
disconnected from the computer in an orderly fashion.
Never turn off or unplug a hard drive without dismounting it first.
Doing so could cause data on the drive to be lost or damaged.
Mac Users
Drag the icon for the External Hard drive to the Trash. The drive will
dismount and you can then safely turn if off. You may then unplug the
power cord and data cable if you want to disconnect the drive.
Formatting Your Drive
The G-Force Quad comes preformatted at the factory with the HFS
Plus file system, which will mount on Mac OS computers. If you
are not using Mac OS exclusively, we recommend you reformat the
volume to a file system format more compatible with your particular
computer and operating system environment.
Formatting a hard drive erases all data contained on it. Please
be sure to create a copy of the files you wish to keep to another
location before reformatting.
Formatting the drive in Mac OS X
1.Launch the “Disk Utility” application located under Applications/
Utilities folder.
2.Highlight your new drive and select the “Partition” tab
3.Select the new partition map type.
4.For each partition in the volume scheme, select the desired
file system format and volume name (optional)
PC Users
The recommended file system is "MacOS Extended"
Left-click on the hot plug icon ( ) in your system tray, located
on the bottom right of your screen. You will receive the alert
message “Safely Remove..” followed by the drive description and
drive letter for the device.
5. Click the “Options” button. Select “Apple Partition Map” in the
dialog box and click “OK”.
6.Click “Apply.” Your Fantom Drives G-Force Quad is ready to
use!
(eSATA) If the ( ) icon does not appear it means that the
current installed driver for your eSATA host bus adapter does
not support hot plugging- this may be due to a hardware
limitation or simply that this feature is missing from the driver
installed. Check with your eSATA host bus adapter vendor for
updated drivers.
Left-click on the appropriate device (with the drive letter matching
the one used by the External Hard drive). After a few seconds,
Windows will give you a message that it is safe to remove the device.
3
3
4
2
5
6
10
11
Formatting the drive in
Windows Hosts
Optimizing Windows Caching Algorithm
2a. Right-click on the drive letter and select Format in the pop-up
menu. The Format dialog box will appear. If the hard disk is not
signed for use, the New Partition option will be unavailable. In
this case a signature can be written on the hard drive by right
clicking on the disk description window and selecting "Initialize
Disk". The following dialog box will prompt you to choose The
partition style for the new volume- select MBR for volumes
smaller then 2TB, or GPT for volumes larger then 2TB or for
volumes that you do not
need to access with
Windows XP or earlier.
By default, Windows XP optimizes caching for performance on
external drives. Windows Vista and 7 optimize caching for quick
removal. As a result, Windows XP appears to have faster
access to external disks but at a greater risk of data corruption
and loss. To change Windows'
caching algorithm, open the
disk management console (as
described on page 8) on your
system drive. A list of the
attached drives and their
respective volumes will appear.
Right-click on the Fantom
external disk in the disk list and
select properties. Select the
Policies Tab near the top left of
the window, and click your
desired optimization level.
press OK when finished, and
you may close the disk
management applet.
2b. If your drive has
no drive letter, find your
disk by verifying the
drive capacity. It should
be close to the stated
capacity of your drive in
gigabytes. If the volume
is unallocated, select
the disk, and right-click
the "unallocated" section of the volume. In the context menu,
left-click "New Simple Volume." The new volume dialog box will
appear. Follow the on screen instructions to complete volume
formatting.
Optimizing for performance can greatly enhance the throughput
of your disk but is much more vulnerable to data loss! Make
sure to have appropriate backup strategies before enabling
this feature!
1. Open the disk management console. A list of the attached drives
and their respective volumes will appear. Select the Fantom Disk.
The Disk Management Console can be accessed by right-clicking on
) and selecting "Manage" from
the "My Computer" icon (
the drop down menu. Disk Management is found under "Storage" in
the resultant window. For an illustrated guide, please see
http://www.fantomdrives.com/helpdesk/faq
3. In the File System pop-up menu, select NTFS. The default
formatting option is full format. A full format will fully verify the
disk media. A Quick format is quick, but will do less verifying of
the drive than a full format. Click Start. Once the format process
is complete, your external hard drive is ready to use.