Download Panasonic Toughpad FZ-G1 4G Black, Silver

OPERATING INSTRUCTIONS
Personal Computer
Read Me First
Safety Precautions........................................... 2
Regulatory Information..................................... 7
Getting Started
Introduction..................................................... 14
Description of Parts........................................ 16
First-time Operation........................................ 18
Turning On / Turning Off................................. 22
Useful Information
Handling and Maintenance............................. 23
Installing Software.......................................... 27
Troubleshooting
Troubleshooting (Basic).................................. 32
Read Me First
Contents
FZ-G1 series
Getting Started
Model No.
Useful Information
A2
Troubleshooting
A1
LIMITED USE LICENSE AGREEMENT......... 38
Specifications................................................. 42
LIMITED WARRANTY.................................... 47
Appendix
Appendix
Please read these instructions carefully before using this product, and save this manual for future use.
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
1
2013/05/09
18:39:48
Safety Precautions
To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to
equipment or property, always observe the
following safety precautions.
Explanation of symbol word panels
Read Me First
The following symbol word panels are used
to classify and describe the level of hazard,
injury, and property damage caused when the
denotation is disregarded and improper use is
performed.
DANGER
Denotes a potential hazard that will result in
serious injury or death.
WARNING
Denotes a potential hazard that could result
in serious injury or death.
CAUTION
Denotes a hazard that could result in minor
injury.
NOTICE
Denotes a hazard that could result in property damage.
The following symbols are used to classify
and describe the type of instructions to be
observed.
These symbols are used to alert users
to a specific operating procedure that
must not be performed.
This symbol is used to alert users to
a specific operating procedure that
must be followed in order to operate
the unit safety.
DANGER
Precautions on the Battery Pack
Do Not Throw the Battery Pack into
a Fire or Expose It to Excessive Heat
Generation of heat, ignition or rupture
may result.
Do Not Insert Sharp Objects Into
the Battery Pack, Disassemble, or
Modify It
Electrolyte leakage, generation of heat,
ignition or rupture may result.
Do Not Short the Positive (+) and
Negative (-) Contacts
Generation of heat, ignition or rupture
may result.
• Do not place the battery pack together with articles such as necklaces or hairpins when carrying or
storing.
Avoid Extreme Heat (Near the Fire,
in Direct Sunlight, for Example)
Electrolyte leakage, generation of heat,
ignition or rupture may result.
Do Not Apply Shocks to the Product by Dropping It, Applying Strong
Pressure to It, etc.
Electrolyte leakage, generation of heat,
ignition or rupture of the battery may
result.
• If this product is subjected to a
strong impact, damaged or deformed, stop using it immediately.
Do Not Charge the Battery Using
Methods Other Than Those Specified
If the battery is not charged using one
of the specified methods, electrolyte
leakage, generation of heat, ignition or
rupture may result.
When the Battery Pack Has Deteriorated, Replace It With a New One
Continued use of a damaged battery
pack may result in heat generation,
ignition or battery rupture.
2
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
2
2013/05/09
18:39:49
Precautions on the Battery Pack
Do Not Use with Any Other Product
The battery pack is rechargeable and
was intended for the specified product.
If it is used with a product other than
the one for which it was designed,
electrolyte leakage, generation of heat,
ignition or rupture may result.
Do Not Use This Product with a Battery Pack Other Than the One Specified
Use only the specified battery pack
( page 18) with your product.
Use of battery packs other than those
manufactured and supplied by Panasonic may present a safety hazard
(generation of heat, ignition or rupture).
WARNING
If a Malfunction or Trouble Occurs,
Immediately Stop Use
If a Malfunction Occurs, Immediately
Unplug the AC Plug and the Battery
Pack
• This product is damaged
• Foreign object inside this product
• Smoke emitted
• Unusual smell emitted
• Unusually hot
Continuing to use this product while
any of the above conditions are present may result in fire or electric shock
• If a malfunction or trouble occurs,
immediately turn the power off and
unplug the AC plug, and then remove the battery pack. Then contact your technical support office for
repair.
Do Not Touch This Product in a
Thunderstorm If Connected with the
AC Cable or Any Other Cables
Electric shock may result.
Do Not Connect the AC Adaptor to
a Power Source Other Than a Standard Household AC Outlet
Otherwise, a fire due to overheating
may result. Connecting to a DC/AC
converter (inverter) may damage the
AC adaptor. On an airplane, only connect the AC adaptor/charger to an AC
outlet specifically approved for such
use.
Do Not Pull or Insert the AC Plug If
Your Hands Are Wet
Electric shock may result.
Read Me First
DANGER
Clean Dust and Other Debris of the
AC Plug Regularly
If dust or other debris accumulates
on the plug, humidity, etc. may cause
a defect in the insulation, which may
result in a fire.
• Pull the plug, and wipe it with a dry
cloth.
Pull the plug if the computer is not
being used for a long period of time.
Insert the AC Plug Completely
If the plug is not inserted completely,
fire due to overheating or electric shock
may result.
• Do not use a damaged plug or loose
AC outlet.
Close the Connector Cover Tightly
When Using This Product Where
Is a Lot of Water, Moisture, Steam,
Dust, Oily Vapors, etc.
The entry of foreign matter may cause
a fire or electric shocks.
• If foreign matter has found its way
inside, immediately turn the power
off and unplug the AC cord, and
then remove the battery pack. Then
contact your technical support office.
Do Not Disassemble This Product
You may receive an electric shock, or
foreign matter may enter and result in
a fire.
3
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
3
2013/05/09
18:39:49
Safety Precautions
WARNING
Do Not Turn the Volume Up to Loud
When Using Headphones
Listening at high volumes that overstimulate the ear for long periods of
time may result in loss of hearing.
Read Me First
Do Not Use This Product in Close
Contact With Your Body for a Long
Period of Time
• Depending on the direction of the
computer or the way you hold the
computer, yourhands and body will
be more exposed to the hot wind.
• Using this product with exposing
the skin to the heat source of this
product or AC adaptor for a long
period of time can cause a lowtemperature burn.
Do Not Do Anything That May Damage the AC Cord, the AC Plug, or the
AC Adaptor
Do not damage or modify the cord,
place it near hot tools, bend, twist, or
pull it forcefully, place heavy objects
on it, or bundle it tightly. Continuing to
use a damaged cord may result in fire,
short circuit, or electric shock.
Do Not Expose Yourself or Other
Persons to the Hot Wind from the
Ventilation Hole (Exhaust) For a
Long Period of Time
Low-temperature burns may result.
Covering the ventilation hole (exhaust)
with your hand or other object can
cause heat to build up inside, possibly
resulting in burns.
CAUTION
Do Not Place This Product on Unstable Surface
If balance is lost, this product may fall
over or drop, resulting in an injury.
Avoid Stacking
If balance is lost, this product may fall
over or drop, resulting in an injury.
Do Not Leave This Product in High
Temperature Environment for a
Long Period of Time
Leaving this product where it will be exposed to extremely high temperatures
such as near fire or in direct sunlight
may deform the cabinet and/or cause
trouble in the internal parts. Continued
use in such a resulting condition may
lead to short-circuiting or insulation
defects, etc. which may in turn lead to
a fire or electric shocks.
Do Not Block the Ventilation Hole
(Exhaust/Intake)
Using this product wrapped in cloth
or on top of bedding or a blanket can
block the ventilation hole and cause
heat to build up inside, possibly resulting in a fire.
Hold the Plug When Unplugging the
AC Plug
Pulling on the cord may damage the
cord, resulting in a fire or electric
shock.
Do Not Move This Product While the
AC Plug Is Connected
The AC cord may be damaged, resulting in fire or electric shock.
• If the AC cord is damaged, unplug
the AC plug immediately.
Use Only the Specified AC Adaptor
With This Product
Using an AC adaptor other than the
one supplied (supplied with the unit or
one sold separately as an accessory)
may result in a fire.
Do Not Subject the AC Adaptor to
Any Strong Impact
Using the AC adaptor after a strong impact such as being dropped may result
in electric shock, short circuit, or fire.
Take a Break of 10-15 Minutes Every
Hour
Using this product for long periods of
time may have detrimental health effects on the eyes or hands.
4
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
4
2013/05/09
18:39:49
<Only for mode with LAN port>
Do Not Connect a Telephone Line,
or a Network Cable Other Than the
One Specified, into the LAN Port
If the LAN port is connected to a network such as the ones listed below, a
fire or electric shock may result.
• Networks other than 1000BASE-T,
100BASE-TX or 10BASE-T
• Phone lines (IP phone (Internet Protocol Telephone), Telephone lines,
internal phone lines (on-premise
switches), digital public phones,
etc.)
Do Not Expose the Skin to This
Product When Using the Product In
a Hot or Cold Environment.
Burns, low-temperature burns or frostbite may result.
• When it is necessary to expose the
skin to this product such as to scan
a fingerprint, perform the operation
in the shortest time possible.
NOTICE
l Do not place the computer near a television or radio receiver.
l Keep the computer away from magnets.
Data stored on the flash memory may be
lost.
l This computer is not intended for the display of images for use in medical diagnosis.
l This computer is not intended for a use
with connection of medical equipment for
the purpose of medical diagnosis.
l Panasonic shall not be liable for loss of
data or other incidental or consequential
damages resulting from the use of this
product.
l Do not touch the terminals on the battery
pack. The battery pack may no longer
function properly if the contacts are dirty or
damaged.
l Do not expose the battery pack to water,
or allow it to become wet.
l If the battery pack will not be used for a
long period of time (a month or more),
charge or discharge (use) the battery pack
until the remaining battery level becomes
30% to 40% and store it in a cool, dry
place.
l This computer prevents overcharging of
the battery by recharging only when the
remaining power is less than approx. 95%
of capacity.
l The battery pack is not charged when the
computer is first purchased. Be sure to
charge it before using it for the first time.
When the AC adaptor is connected to the
computer, charging begins automatically.
l Should the battery leak and the fluid get
into your eyes, do not rub your eyes. Immediately flush your eyes with clear water
and see a doctor for medical treatment as
soon as possible.
Read Me First
CAUTION
NOTE
lThe battery pack may become warm during recharging or normal use. This is completely normal.
lRecharging will not commence if internal
5
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
5
2013/05/09
18:39:50
Safety Precautions
Read Me First
temperature of the battery pack is outside
of the allowable temperature range (0 °C to
50 °C {32 °F to 122 °F}). ( Reference
Manual “Battery Power”) Once the allowable range requirement is satisfied, charging begins automatically. Note that the
recharging time varies based on the usage
conditions. (Recharging takes longer than
usual when the temperature is 10 °C {50 °F}
or below.)
lIf the temperature is low, the operating
time is shortened. Only use the computer
within the allowable temperature range.
lThis computer has a high temperature
mode function that prevents the degradation of the battery in high temperature
environments. ( Reference Manual
“Battery Power”) A level corresponding to
a 100% charge for high temperature mode
is approximately equivalent to an 80%
charge level for normal temperature mode.
lThe battery pack is a consumable item.
If the amount of time the computer can
be run by using a particular battery pack
becomes dramatically shorter and repeated recharging does not restore its
performance, the battery pack should be
replaced with a new one.
lWhen transporting a spare battery inside a
package, briefcase, etc., it is recommended that it be placed in a plastic bag so that
its contacts are protected.
lAlways power off the computer when it is
not in use. Leaving the computer on when
the AC adaptor is not connected will exhaust the remaining battery capacity.
THIS PRODUCT IS NOT INTENDED FOR
USE AS, OR AS PART OF, NUCLEAR
EQUIPMENT/SYSTEMS, AIR TRAFFIC
CONTROL EQUIPMENT/SYSTEMS, AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1,
MEDICAL DEVICES OR ACCESSORIES*2,
LIFE SUPPORT SYSTEMS OR OTHER
EQUIPMENTS/DEVICES/SYSTEMS THAT
ARE INVOLVED WITH ENSURING HUMAN
LIFE OR SAFETY. PANASONIC WILL NOT
BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING
USES.
*1
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS
include Class2 Electronic Flight Bag (EFB) Systems and Class1 EFB Systems when used during critical phases of flight (e.g., during take-off
and landing) and/or mounted on to the aircraft.
Class1 EFB Systems and 2 EFB Systems are
defined by FAA: AC (Advisory Circular) 120-76A
or JAA: JAA TGL (Temporary Guidance Leaflets)
No.36.
*2
As defined by the European Medical Device
Directive (MDD) 93/42/EEC.
Panasonic cannot guarantee any specifications, technologies, reliability, safety (e.g.
Flammability/Smoke/Toxicity/Radio Frequency Emission, etc) requirements related
to aviation standards that exceed the specifications of our COTS (Commercial-Off-TheShelf) products.
6
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
6
2013/05/09
18:39:50
Regulatory Information
Information to the User / Informations destinées aux utilisateurs
Regulatory Information
We are not responsible for any radio or television interference caused by unauthorized
modification of this product. The correction
of interference caused by such unauthorized
modification will be the responsibility of the
user. We and its authorized resellers or distributors are not liable for damage or violation
of government regulations that may arise from
failing to comply with these guidelines.
consommateur du fait que cet appareil opère
dans les limites des directives concernant
les normes et les recommendations de sécurité sur les fréquences radio. Ces normes et
recommandations reflètent le consensus de
la communauté scientifique et résultent de
délibérations de jurys et comités de scientifiques qui examinent et interprètent continuellement les nouveautés de la vaste littérature
sur les recherches effectuées. Dans certaines
situations ou environnements, l’utilisation de
ce produit peut être restreinte par le propriétaire du bâtiment ou par les représentants
responsables de l’organisation. Ces situations
peuvent être les suivantes par exemple :
l A bord d’un avion, ou
l Dans tout autre environnement où les
risques d’interférence sur d’autres appareils ou services sont perçus ou identifiables comme dangereux.
Si vous n’êtes pas sûr de la réglementation
applicable à
l’utilisation d’appareils sans fil dans une organization ou un environnement spécifique, (par
exemple dans un aéroport) nous vous invitons
à demander l’autorisation
d’utiliser ce produit avant sa mise en marche.
Read Me First
<Only for model with wireless LAN/Bluetooth>
This product and your Health
This product, like other radio devices, emits
radio frequency electromagnetic energy. The
level of energy emitted by this product however is far much less than the electromagnetic
energy emitted by wireless devices like for
example mobile phones.
Because this product operates within the
guidelines found in radio frequency safety
standards and recommendations, we believe this product is safe for use by consumers. These standards and recommendations
reflect the consensus of the scientific community and result from deliberations of panels
and committees of scientists who continually
review and interpret the extensive research
literature.
In some situations or environments, the use
of this product may be restricted by the proprietor of the building or responsible representatives of the organization. These situations
may for example include:
l Using this product on board of airplanes,
or
l In any other environment where the risk of
interference to other devices or services is
perceived or identified as harmful.
If you are uncertain of the policy that applies
on the use of wireless devices in a specific organization or environment (e.g. airports), you
are encouraged to ask for authorization to use
this product prior to turning on the product.
Informations concernant la réglementation
Nous déclinons toute responsabilité pour
toute interférence radio ou télévision causée
par des modifications non autorisées apportées à ce produit. La correction
d’interférences causées par de telles modifications non autorisées sera la seule responsabilité de son utilisateur. Nousmêmes, les
revendeurs officiels et les distributeurs ne
sommes pas responsable de tout dégât ou de
toute violation des règlements de l’État pouvant découler du non-respect de ces directives.
26-F-1
26-M-1
<Uniquement pour les modèles avec réseau
local sans fil et/ou Bluetooth>
Ce produit et votre santé
Ce produit, comme tout autre appareil radio,
émet de
l’énergie radioélectrique. Toutefois, la quantité
d’énergie émise par ce produit est beaucoup
moins importante que l’énergie radioélectrique émise par des appareils sans fil tels
que les téléphones portables. L’utilisation de
ce produit ne comporte aucun risque pour le
7
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
7
2013/05/09
18:39:50
Regulatory Information
Lithium Battery / Pile au lithium
Lithium Battery!
This computer contains a lithium battery to
enable the date, time, and other data to be
stored. The battery should only be exchanged
by authorized service personnel.
Warning!
A risk of explosion from incorrect installation
or misapplication may possibly occur.
Read Me First
15-E-1
Pile au lithium!
Le micro-ordinateur renferme une pile au
lithium qui permet de sauvegarder certaines
données, notamment la date et l’heure. La
pile ne doit être remplacée que par un technicien qualifié.
Danger ! Risque d’explosion en cas de non
respect de cette mise en garde!
15-F-1
Information for Users on Collection and Disposal of Old Equipment and used Batteries
These symbols are only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
53-M-1
Safety Precautions
<Only for model with wireless WAN>
The following safety precautions must be observed during all phases of the operation, usage, service or repair of any Personal Computer or Handheld Computer incorporating wireless WAN modem. Manufacturers of the cellular terminal are advised to convey the following safety information
to users and operating personnel and to incorporate these guidelines into all manuals supplied
with the product. Failure to comply with these precautions violates safety standards of design,
manufacture and intended use of the product. Panasonic assumes no liability for customer failure
to comply with these precautions.
When in a hospital or other health care facility, observe the restrictions on the use of
mobiles. Switch Personal Computer or Handheld Computer incorporating wireless WAN
modem off, if instructed to do so by the guidelines posted in sensitive areas. Medical
equipment may be sensitive to RF energy.
The operation of cardiac pacemakers, other implanted medical equipment and hearing
aids can be affected by interference from Personal Computer or Handheld Computer
incorporating wireless WAN modem placed close to the device. If in doubt about potential danger, contact the physician or the manufacturer of the device to verify that the
equipment is properly shielded. Pacemaker patients are advised to keep their Personal
Computer or Handheld Computer incorporating wireless WAN modem away from the
pacemaker, while it is on.
Switch off Personal Computer or Handheld Computer incorporating wireless WAN modem before boarding an aircraft. Make sure it cannot be switched on inadvertently. The
operation of wireless appliances in an aircraft is forbidden to prevent interference with
communications systems. Failure to observe these instructions may lead to the suspension or denial of cellular services to the offender, legal action, or both.
For details on usage of this unit in aircrafts please consult and follow instruction provided by the airline.
8
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
8
2013/05/09
18:39:50
Do not operate Personal Computer or Handheld Computer incorporating wireless WAN
modem in the presence of flammable gases or fumes. Switch off the cellular terminal
when you are near petrol stations, fuel depots, chemical plants or where blasting operations are in progress. Operation of any electrical equipment in potentially explosive
atmospheres can constitute a safety hazard.
Your Personal Computer or Handheld Computer incorporating wireless WAN modem receives and transmits radio frequency energy while switched on. Remember that interference can occur if it is used close to TV sets, radios, computers or inadequately shielded
equipment. Follow any special regulations and always switch off Personal Computer or
Handheld Computer incorporating wireless WAN modem wherever forbidden, or when
you suspect that it may cause interference or danger.
Read Me First
Road safety comes first! Do not use a Personal Computer or Handheld Computer incorporating wireless WAN modem while driving a vehicle. Do not place the computer
with wireless WAN modem in an area where it could cause personal injury to the driver
or passengers. It is recommended to stow the unit in the boot or secure stowage area
while driving.
Do not place the computer with wireless WAN modem in an area over an air bag or in
the vicinity where an air bag may deploy.
Air bags inflate with great force and if the computer with wireless WAN modem is placed
in the air bag deployment area may be propelled with great force and cause serious
injury to occupants of the vehicle.
IMPORTANT!
Personal Computer or Handheld Computer incorporating wireless WAN modem operate
using radio signals and cellular networks cannot be guaranteed to connect in all conditions. Therefore, you should never rely solely upon any wireless device for essential
communications, for example emergency calls.
Remember, in order to make or receive calls, Personal Computer or Handheld Computer incorporating wireless WAN modem must be switched on and in a service area with
adequate cellular signal strength.
Some networks do not allow for emergency calls if certain network services or phone
features are in use (e.g. lock functions, fixed dialing etc.). You may need to deactivate
those features before you can make an emergency call.
Some networks require that a valid SIM card be properly inserted in Personal Computer
or Handheld Computer incorporating wireless WAN modem.
CAUTION:
Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used Batteries According to the
Instructions.
ATTENTION:
Il y a risque d’explosion si la batterie est remplacée par une batterie de type incorrect.
Mettre au rebut les batteries usagées conformément aux instructions.
58-E-1
58-F-1
Camera Light
<For model with rear camera>
CAUTION
- The light from the LED is strong and can injure human eyes. Do not look directly at the LEDs
with naked eyes.
57-E-1
9
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
9
2013/05/09
18:39:50
Regulatory Information
For U.S.A.
Read Me First
Federal Communications Commission
Radio Frequency Interference Statement
Note: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the
equipment and receiver.
l Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
l Consult the Panasonic Service Center or
an experienced radio/TV technician for
help.
Warning
To assure continued compliance, use only
shielded interface cables when connecting to
a computer or peripheral. Also, any changes
or modifications not expressly approved by
the party responsible for compliance could
void the user’s authority to operate this equipment.
FCC RF Exposure Warning:
l This equipment is provided with PC Card
slot that could be used with wireless transmitters, which will be specifically recommended when they become available.
Other third-party wireless transmitters
have not been RF exposure evaluated for
use with this computer and may not comply with FCC RF exposure requirements.
<Only for model with wireless LAN/wireless
WAN/Bluetooth>
l This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
l This equipment may not be co-located or
operated with any other antenna or transmitter.
l This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured
not to exceed the emission limits for exposure to radio frequency (RF) energy set by
the Federal Communications Commission
of the U.S. Government.
l The exposure standard for wireless device
employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC is
1.6 W/kg.
*Tests for SAR are conducted using standard operating positions accepted by the
FCC with the device transmitting at its
highest certified power level in all tested
frequency bands.
Although the SAR is determined at the
highest certified power level, the actual
SAR level of the device while operating
can be well below the maximum value.
This is because the device is designed
to operate at multiple power levels so as
to use only the poser required to reach
the network. In general, the closer you
are to a wireless base station antenna,
the lower the power output.
<Only for model with wireless LAN>
This product is restricted to indoor use due
to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to
be used indoors for the frequency range 5.15
to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite
systems. High power radars are allocated
as primary users of the 5.25 to 5.35 GHz
and 5.65 to 5.85 GHz bands. These radar
stations can cause interference with and/or
damage this product.
25-M-W-1
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference
received, including interference that may
cause undesired operation.
Responsible Party:Panasonic Corporation of
North America
One Panasonic Way
Secaucus, NJ 07094
Tel No:1-800-LAPTOP5
(1-800-527-8675)
6-M-1
10
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
10
2013/05/09
18:39:50
A lithium ion battery that
is recyclable powers the
product you have purchased.
Please call 1-800-8-BATTERY for information on
how to recycle this battery.
L’appareil que vous vous
êtes procuré est alimenté par une batterie au
lithium-ion.
Pour des renseignements sur le recyclage
de la batterie, veuillez
composer le
1-800-8-BATTERY.
Read Me First
FCC RF Exposure Warning:
l This equipment is provided with external
antenna connector(s) for connection to
optional Car Mounter or Port Replicator
for mobile external mounted antenna(s).
External antenna(s) must be professionally
installed and cannot exceed recommended
maximum antenna gain as described in
individual provided supplement instructions
for wireless transmitters. The Car Mounter
is provided with Radiall/Larsen WLAN whip
antenna, type NMO5E2400BKTNC with
5dBi antenna gain. The maximum allowable antenna gain for the external WWAN
base whip antenna for the cellular band
is 4 dBi, PCS band is 3 dBi, LTE Band 4
is 3 dBi, LTE Band 17 is 9 dBi and 10 dBi
for LTE Band 13. Also, user must maintain
minimum 20 cm spacing between external
antenna(s) and all person’s body (excluding
extremities of hands, wrist and feet) during
wireless modes of operation.
48-M-1
32-M-1
USA Only: Disposal may be regulated in your
community due to environmental considerations. For disposal or recycling information,
please visit Panasonic website: http://www.
panasonic.com/environmental or call 1-888769-0149
65-M-2
<For USA-California Only>
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/
38-M-1
11
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
11
2013/05/09
18:39:51
Regulatory Information
For Canada
Canadian ICES-003
CAN ICES-3(B)/NMB-3(B)
7-M-2
Read Me First
<Only for model with wireless LAN/Bluetooth>
Industry Canada
This product complies with RSS210 Industry
Canada.
Operation is subject to the following two conditions;
(1)this device may not cause interference,
and
(2)this device must accept any interference,
including interference that may cause undesired operation of the device.
<Ne s’applique qu’aux modèles avec technologie Bluetooth/LAN sans fil>
Industrie Canada
Cet équipement est conforme à la norme
CNR-210
d’Industrie Canada. Son fonctionnement est
soumis aux deux conditions suivantes :
(1)ce dispositif ne peut produire de brouillage,
et
(2)ce dispositif doit accepter le brouillage, y
compris le brouillage pouvant entraîner le
fonctionnement non désiré de l’appareil.
30-Ca-1-1
<Only for model with wireless LAN>
This product (local network devices) for the
band 5150-5250 MHz is only indoor usage
to reduce potential for harmful interference to
co-channel Mobile Satellite systems.
High power radars are allocated as primary
users (meaning they have priority) of 52505350 MHz and 5650-5850 MHz and these
radars could cause interference and/or damage to LELAN devices.
<Ne s’applique qu’aux modèles avec technologie LAN sans fil>
Cet appareil (pour réseaux locaux radioélectriques) dans les bandes de fréquences
5150-5250 MHz est réservé à une utilization
à l’intérieur afin de réduire le risque d’interférence avec les systèmes satellites mobiles
bicanaux.
Les radars forte puissance sont désignés
comme étant les premiers utilisateurs (c’est-àdire qu’ils ont la priorité) des bandes de fréquences 5250-5350 MHz et 5650-5850 MHz.
Ces stations radars peuvent provoquer des
interférences et/ou des dommages à ce périphérique.
<Only for model with wireless LAN/wireless
WAN/Bluetooth>
l This computer complies with Industry
Canada radiation exposure limits set forth
for an uncontrolled environment.
l This PC with WLAN and/or Bluetooth
transmitters installed, has been approved
for portable operation and does not require
any minimum spacing be provided between antennas and all person’s body.
<Ne s’applique qu’aux modèles avec technologie Bluetooth/LAN sans fil/WAN sans fil>
l Cet équipement est conforme aux limites
d’exposition aux rayonnements d’Industrie
Canada établies pour un environnement
non contrôlé.
l Ce PC avec émetteurs WLAN et/ou Bluetooth a été approuvé à des fins d’opération
mobile; aucun espace minimum entre les
antennes et le corps de l’utilisateur n’est
requis.
This device has been designed to operate
with the Radiall/Larsen whip antenna, type
NMO5E2400BKTNC WLAN antenna having
a maximum gain of 5dB. A WLAN Antenna
having a higher gain is strictly prohibited per
regulations of Industry Canada. The Required
antenna impedance is 50 ohms.
To reduce potential radio interference to other
users, the antenna type and its gain should
be so chosen that the equivalent isotropically
radiated power (EIRP) is not more than that
required for successful communication.
Cet appareil est conçu pour opérer avec
l’antenne-fouet Radiall/Larsen, type WLAN
NMO5E2400BKTNC, ayant un gain maximum
de 5 dB. Les règlements d’Industrie Canada
interdisent l’utilisation d’une antenne WLAN
dont le gain serait supérieur à cette limite.
L’antenne doit avoir une impédance de 50
ohms.
Afin de réduire le risque d’interférence radioélectrique aux autres utilisateurs des
bandes de fréquences, le type d’antenne et
son gain doivent être tels que la puissance
isotrope rayonnée équivalente (PIRE) n’est
pas plus élevée que le niveau requis pour assurer la communication.
25-Ca-1-1
30-Ca-2-1
12
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
12
2013/05/09
18:39:51
<Ne s’applique qu’aux modèles avec technologie Bluetooth/LAN sans fil/WAN sans fil>
* Cet équipement est conforme aux limites
d’exposition aux rayonnements d’Industrie
Canada établies pour un environnement non
contrôlé.
* Ce PC avec émetteurs WLAN et/ou
Bluetooth a été approuvé à des fins
d’opération mobile; aucun espace minimum
entre les antennes et le corps de l’utilisateur
n’est requis..
This device has been designed to operate
with the WWAN antenna having a maximum gain of 4 dBi for Cellular band, 3 dBi
for the PCS band and 5.5 dBi for LTE Band
4. WWAN Antenna having a higher gain is
strictly prohibited per regulations of Industry
Canada. The Required antenna impedance is
50 ohms.
To reduce potential radio interference to other
users, the antenna type and its gain should
be so chosen that the equivalent isotropically
radiated power (EIRP) is not more than that
required for successful communication.
<Utilisation au Canada>
Cet appareil est conçu pour opérer avec une
antenne WWAN (réseau étendu sans fil) dont
le gain maximum est fixé à [X1] pour la bande
cellulaire et à 4 dBi pour la bande cellulaire,
3 dBi pour la bande PCS et 5.5 dBi pour la
bande LTE Band 4. Les règlements d’Industrie
Canada interdisent l’utilisation d’une antenne
WWAN dont le gain serait supérieur à cette
limite. L’antenne doit avoir une impédance de
50 ohms.
Afin de réduire le risque d’interférence radioélectrique aux autres utilisateurs des
bandes de fréquences, le type d’antenne et
son gain doivent être tels que la puissance
isotrope rayonnée équivalente (PIRE) n’est
pas plus élevée que le niveau requis pour assurer la communication.
Read Me First
<Only for model with wireless LAN/wireless
WAN/Bluetooth>
* This computer complies with Industry
Canada radiation exposure limits set forth
for an uncontrolled environment.
* This PC with WLAN and/or Bluetooth
transmitters installed, has been approved
for portable operation and does not require
any minimum spacing be provided between
antennas and all person’s body.
32-Ca-1-1
FOR USE WITH MODEL NO. : CF-AA6413C
POUR UTILISER AVEC MODÈLE : CF-AA6413C
20-Ca-1
For India
For the purpose of recycling to facilitate effective utilization of resources, please return
this product to a nearby authorized collection center, registered dismantler or recycler,
or Panasonic service center when disposing of this product.
Please see the Panasonic website for further information on collection centers, etc.
http://www.panasonic.co.in/wps/portal/home
68-M-1
13
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
13
2013/05/09
18:39:51
Introduction
Thank you for purchasing this Panasonic product. For optimum performance and safety, please
read these instructions carefully.
In these instructions, the names are referred as follows.
indicates Windows® 8 Operating System.
indicates Windows® 7 Operating System.
n Terms and illustrations in these instructions
CAUTION :
NOTE :
Conditions that may result in minor or moderate injury.
Useful and helpful information.
Press [Enter] key.
Press and hold [Alt] key, and then press [Del] key.
Page in these Operating Instructions or in the Reference Manual.
Reference to the on-screen manuals.
Enter :
Alt + Del :
è :
:
Getting Started
Display “Charm”
Touch [Charm] -
Flick from right side to inside of the screen.
:This illustration means to touch
(Settings) in the Charm menu.
(Start) - [All Programs] : Touch
(Start), and then touch [All Programs].
l Some illustrations are simplified to help your understanding and may look different from the
actual unit.
l If you do not log on as an administrator, you cannot use some functions or cannot display
some screens.
l Refer for the latest information about optional products to the catalogs, etc.
l In these instructions, the names and terms are referred as follows.
®
Ÿ“Windows 8 Pro 64-bit” as “Windows” or “Windows 8”
®
®
Ÿ“Windows 7 Professional 32-bit Service Pack 1” and “Windows 7 Professional 64-bit Service Pack 1” as “Windows” or “Windows 7”
Ÿ DVD MULTI drive as “DVD drive”
l
Screen messages are explained in [English (United States)].
(Depending on the language preference, some screen messages in these instructions are different from the actual screen messages. For example, [Flight mode] may be displayed instead
of [Airplane mode] in some language preference)
nDisclaimer
Computer specifications and manuals are subject to change without notice. Panasonic Corporation assumes no liability for damage incurred directly or indirectly from errors, omissions or discrepancies between the computer and the manuals.
nTrademarks
Microsoft®, Windows®, and the Windows logo are registered trademarks of Microsoft Corporation
of the United States and/or other countries.
Intel, Core, Centrino and PROSet are either registered trademarks or trademarks of Intel Corporation.
microSDXC Logo is a trademark of SD-3C, LLC.
14
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
14
2013/05/09
18:39:51
Adobe, the Adobe logo and Adobe Reader are either registered trademarks or trademarks of
Adobe Systems Incorporated in the United States and/or other countries.
Bluetooth® is a registered trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Panasonic Corporation.
HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.
Names of products, brands, etc., appearing in this manual are trademarks or registered trademarks of their respective own companies.
Getting Started
n On-screen Manual
For further information about the computer, you can refer to the on-screen manual.
l Reference Manual
The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.
l Important Tips
The Important Tips will provide you with the battery information so that you can use the battery
pack in the optimum condition to obtain longer operation time.
To access the on-screen manuals, follow the steps below.
On the Start screen, touch the [Manual Selector] tile, and select the on-screen manual.
Double-touch [Manual Selector] on the desktop screen, and select the on-screen manual.
15
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
15
2013/05/09
18:39:51
Description of Parts
Front side
Right side
㪘
㪙
㪜
㪚
㪛
㪡
㪢
㪣
㪝
㪞
㪟 㪠
Getting Started
Front Camera
Reference Manual “Camera”
è
A: Camera Indicator
B: Camera Lens
C: Microphone
D:Ambient Light Sensor
The ambient light sensor is equipped with
an automatic brightness adjustment function that adjusts the display screen. (è
page 24)
E: Security lock
A Kensington cable can be connected.
For further information, read the manual
that comes with the cable.
F: DC-IN jack
G:Tablet Buttons
Reference Manual “Tablet Buttons”
è
H:LED Indicator
: Power Indicator
Off : Power off/Hibernation, Green:
Power on, Blinking green: Sleep,
Blinking green and orange: Cannot
power on or resume due to low temperature.
: Drive status
: Battery status
è page 24 “When the battery indicator does not light on”
Reference Manual “Battery
è
Power”
I: Power Switch
J: USB3.0 Port
Reference Manual “USB Devices”
è
K:HDMI Port
Reference Manual “External Disè
play”
L: Headset Jack
A headset or headphone can be connected.
16
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
16
2013/05/09
18:39:52
Rear side
㪚 㪛㪜 㪝 㪞 㪟
㪘 㪙
㪠
㪡
㪢
㪨
㪥
A:Ventilation Hole (Intake)
B:Ventilation Hole (Exhaust)
C:Dust Cover
è page 26 “To clean inside of the dust
cover”
D:USB2.0 Port*1 / LAN Port*2 / Serial Port*3 /
MicroSD Memory Card Slot*4
*1
Only for model with USB2.0 port
Reference Manual “USB Devices”
è
*2
Only for model with LAN port
Reference Manual “LAN”
è
*3
Only for model with Serial port
Reference Manual “Serial Port”
è
*4
Only for model with microSD memory
card slot
Reference Manual “MicroSD Memoè
ry Card”
Rear Camera
<Only for model with Rear Camera>
Reference Manual “Camera”
è
E: Camera Indicator
F: Camera Lens
G: Camera light
H:Battery Pack
I: Battery Latch
Reference Manual “Battery Power”
è
J:Wireless LAN Antenna
<Only for model with wireless LAN>
Reference Manual “Wireless LAN”
è
㪦 㪧
K: Wireless WAN Antenna
<Only for model with Wireless WAN>
Reference Manual “Wireless WAN”
è
Getting Started
㪣㪤
L: Smart Card Slot
<Only for model with Smart Card Slot>
Reference Manual “Smart Card”
è
M:External Antenna Connector
N:Expansion Bus Connector
Reference Manual “Cradle”
è
O:Wireless LAN Antenna / Bluetooth Antenna
<Only for model with wireless LAN>
<Only for model with Bluetooth>
Reference Manual “Wireless LAN”
è
“Bluetooth”
P:Speaker
Reference Manual “Dashboard for
è
Panasonic PC”
Q:Pen Holder
17
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
17
2013/05/09
18:39:52
First-time Operation
nPreparation
ACheck and identify the supplied accessories.
If you do not find the described accessories, contact Panasonic Technical Support (è
page 47).
• AC Adaptor. . . 1 • AC Cord. . . . . 1 • Battery Pack . . . . . . 1 • Digitizer pen. . . . . . . 1
Model No:FZ-VZSU84U
Model No: CFAA6413C
Reference Manual
è
“Screen Input Operation”
• Tether. . . . . . . 1 • Soft Cloth. . . . 1
Reference Manual “Screen Input Operation”
è
Getting Started
• OPERATING INSTRUCTIONS (This book). . . . . . . . . . . . . . . . . . . . 1
BRead the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging (è page 38).
1
A
1
B
Inserting the Battery Pack.
Turn over the computer and insert the battery pack until it touch
to the secured position.
l Make sure no foreign objects are under the computer.
CAUTION
l Make sure the latch is securely locked. Otherwise the battery
pack may fall when you carry the computer.
l Do not touch the terminals of the battery pack and the computer.
Doing so can make the terminals dirty or damaged, and may
cause malfunction of the battery pack and the computer.
NOTE
l Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully charged, the battery
will fully discharge in the following period of time:
Status
Discharge period
When power is off Approx. 6 weeks
In sleep
Approx. 4 days
In hibernation
Approx. 7 days
18
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
18
2013/05/09
18:39:53
2
Attaching the pen (included) to the computer.
A Pass one of the loops
through the hole.
㪈
㪉
BPass one of the loops
through another loop.
㪊
㪋
CThread the second loop on
the tether through the hole
as illustrated.
㪈
㪉
㪊
㪋
DPass the pen and tether
through the second loop.
㪋
Getting Started
㪊
CAUTION
l Do not pull the tether with excessive force. The pen (included)
may hit the computer, person’s body or other objects when released.
3
3
Connect your computer to a power outlet.
The battery charging starts automatically.
CAUTION
l Do not disconnect the AC adaptor until the first-time operation
procedure is completed.
l When using the computer for the first time, do not connect any
peripheral device (including wired LAN cable) except the battery
pack and AC adaptor.
l Handling the AC adaptor
Ÿ Problems such as sudden voltage drops may arise during periods of thunder and lightning. Since this could adversely affect
your computer, an uninterruptible power source (UPS) is highly
recommended unless running from the battery pack alone.
㪈
4
㪉
Turn on the computer.
Press and hold the power switch (è page 16) until the
power indicator (è page 16) lights.
CAUTION
l Do not press the power switch repeatedly or do not hold the
power switch for four seconds or longer.
19
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
19
2013/05/09
18:39:54
First-time Operation
5
Setup Windows.
Getting Started
Follow the on-screen instructions.
lThe computer restarts several times. Do not touch the screen
or tablet buttons, and wait until the drive indicator
has
turned off.
lAfter the computer is turned on, the screen remains black or
unchanged for a while, but this is not a malfunction. Wait for
a moment until the Windows setup screen appears.
5 minlSetup of Windows will take approximately
utes /
20 minutes.
Go to the next step, confirming each message on the display.
Follow the steps below.
l
AWhen “Enable sensors” is displayed, touch [Enable this
sensor].
BWhen the [User Account Control] screen is displayed,
touch [Yes].
CAt the [Display Rotation Tool] confirmation screen, touch
[Yes].
The computer restarts automatically, and the setting is enabled.
“Join a wireless network” screen may not apl
pear.
You can set the Wireless Network after the setup of Windows
is complete.
CAUTION
l You can change the user name, password, image and security
setting after setup of Windows.
l Remember your password. If you forget the password, you cannot use Windows. Creating a password reset disk beforehand is
recommended.
l Do not use the following words for user name: CON, PRN,
AUX, CLOCK$, NUL, COM1 to COM9, LPT1 to LPT9, @, &,
space. In particular, if you create a user name (account name)
that includes the “@” mark, a password will be requested at the
log-on screen, even if no password has been set. If you try to
log on without entering a password, “The user name or password is incorrect.” may be displayed and you will not be able
sign in /
log on to Windows (è
to
page 35).
6
Create the recovery disc.
A recovery disc allows you to install OS and restore its factory
default condition, in case, for example, the recovery partition
of the flash memory is damaged. We recommend creating a
recovery disc before you begin using the computer.
Refer to è
Reference Manual “Recovery Disc Creation Utility” about creating the disc.
20
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
20
2013/05/09
18:39:54
NOTE
l PC Information Viewer
This computer periodically records the management information of the flash memory, etc. The
maximum data volume for each record is 1024 bytes.
This information is only used for estimating the cause when the flash memory goes down by
any possibility. They are never sent to outside via network nor used for any other purpose
except for the purpose described the above.
To disable the function, add the check mark for [Disable the automatic save function for management information history] in [Hard Disk Status] of PC Information Viewer, and touch [OK].
(è
Reference Manual “Checking the Computer’s Usage Status”)
nBefore using wireless function
- [Change PC Settings] - [Wireless].
ADisplay “Charm” and touch
Set [Airplane mode] to [Off], and then;
set [Wi-Fi] in “Wireless device” to [On] (for wireless LAN).
set [Mobile broadband] in “Wireless device” to [On] (for wireless WAN).
set [GPS] in “Wireless device” to [On] (for wireless WAN).
set [Bluetooth] in “Wireless device” to [On] (for Bluetooth).
Getting Started
ATouch the Wireless Switch Utility icon to show the pop-up menu.
BSelect ON for the device you want to enable.
n To change the partition structure
You can shrink a part of an existing partition to create unallocated disk space, from which you can
create a new partition. In the default setting, you can use a single partition.
A
Open “Computer”. Long touch [Computer], then touch [Manage].
To open “Computer”, proceed as follows on the Start screen.
1.On the Start screen, flick from bottom side to inside of the screen.
2.Touch [All apps] on the toolbar.
3.Touch [Computer] under “Windows System”.
(Start) and long touch [Computer], then touch [Manage].
Touch
l A standard user needs to enter an administrator password.
BTouch [Disk Management].
CLong touch the partition for Windows (“c” drive in the default setting), and touch [Shrink
Volume].
l The partition size depends on the computer specifications.
D Input the size in [Enter the amount of space to shrink in MB] and touch [Shrink].
l You cannot input a larger number than the displayed size.
l To select [Reinstall to the System and OS partitions.] in installing OS (è page 28),
70 GB /
60 GB or more is necessary for [Total size after shrink
in MB].
ELong touch [Unallocated] (the shrunk space in the step D) and touch [New Simple Volume].
F Follow the on-screen instructions to make the settings, and touch [Finish].
Wait until formatting is completed.
NOTE
l You can create an additional partition using remaining unallocated space or newly creating
unallocated space.
l To delete a partition, long touch the partition and touch [Delete Volume] in the step C.
21
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
21
2013/05/09
18:39:55
Turning On / Turning Off
Turning On
Press and hold the power switch
lights.
(è page 16) until the power indicator
(è page 16)
NOTE
l Do not press the power switch repeatedly.
l The computer will forcibly be turned off if you press and hold the power switch for four seconds or longer.
l Once you turn off the computer, wait for ten seconds or more before you turn on the computer
again.
turns off.
l Do not perform the following operation until the drive indicator
Ÿ Connecting or disconnecting the AC adaptor
Ÿ Pressing the power switch
ŸTouching the tablet buttons, screen or external mouse/keyboard
Turning Off
Getting Started
AShut down the computer.
1. Display “Charm” and touch .
2. Touch [Power] - [Shut down].
Touch
(Start) - [Shutdown].
NOTE
l
To turn off the computer, proceed as follows.
- [Change PC settings] - [General].
ADisplay “Charm” and touch
BTouch [Restart now] under “Advanced startup”.
CTouch [Turn off your PC].
Precaution against Starting Up/Shutting Down
l Do not do the following
Ÿ Connecting or disconnecting the AC adaptor
ŸPressing the power switch
Ÿ Touching the screen or external mouse/keyboard
NOTE
l To conserve power, the following power saving methods are set at the time of purchase.
ŸThe screen automatically turns off after :
10 minutes (when AC adaptor is connected) of inactivity
5 minutes (when operating on battery power) of inactivity
*1
ŸThe computer automatically enters sleep after :
30 minutes /
20 minutes (when AC adaptor is connected) of inactivity
15 minutes (when operating on battery power) of inactivity
*1
Refer to
Reference Manual “Sleep and Hibernation Functions” about resuming from sleep.
22
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
22
2013/05/09
18:39:55
Handling and Maintenance
Operation environment
l Place the computer on a flat stable surface not subject to shock, vibration, and danger of
dropping. Do not place the computer upright or turn it over. If the computer is exposed to an
extremely strong impact, it may become damaged.
l Operating environment
Temperature: Operation : -10 °C to 50 °C {14 °F to 122 °F} (IEC60068-2-1, 2)*1
Storage : -20 °C to 60 °C {-4 °F to 140 °F}
Humidity:
Operation : 30% to 80% RH (No condensation)
Storage : 30% to 90% RH (No condensation)
Even within the above temperature/humidity ranges, operation for a long time in extreme environments, smoking nearby, or operation in places where oil is used or where there is a lot of
dust will result in the product deterioration and will shorten the product life.
*1
Do not expose the skin to this product when using the product in a hot or cold environment. (è
page 5)
If the computer is wet in temperatures of 0 °C {32 °F} or below, freeze damage may occur.
Make sure to dry off the computer in such temperatures.
l Do not place the computer in the following areas, otherwise the computer may be damaged.
Ÿ Near electronic equipment. Image distortion or noise may occur.
Ÿ In extremely high or low temperature.
l As the computer can become hot during operation, keep it away from items that are sensitive
to heat.
Handling cautions
Useful Information
This computer is designed to minimize shock to parts such as the LCD and the flash memory
drive, but no warranty is provided against any trouble caused by shock. Be extremely careful
when handling the computer.
l When carrying the computer:
Ÿ Turn off the computer.
Ÿ Remove all external devices, cables, Smart Cards and other protruding objects.
Ÿ Do not drop or hit the computer against solid objects.
Ÿ Do not grip the display part.
l When you board an airplane, take the computer with you and never put it in your checked luggage. When using the computer on airplane, follow the airline’s instructions.
l When carrying a spare battery, put it in a plastic bag to protect its terminals.
l Avoid any harmful substances such as oil from getting into the touch pad. The pointer may not
work correctly.
l Be careful not to get injured by dropping or getting hit when carrying the computer.
l Use only the included digitizer pen to touch the screen. Do not place any object on its surface
and do not press down strongly with sharp-pointed or hard objects that may leave marks (e.g.,
nails, pencils and ball point pens).
l Do not use the screen when dust or dirt (e.g., oil) is on the screen. Otherwise foreign particles on
the screen/digitizer pen can scratch the screen surface or obstruct the digitizer pen operation.
l Use the digitizer pen only for touching the screen. Using it for any other purpose may damage
the digitizer pen and result in scratches on the screen.
l The digitizer uses electromagnetic induction and may not work properly near strong electrical
field or magnetic field such as:
Ÿ Near AM radio base station or relay station antennas
Ÿ Near CRT displays that generate strong electromagnetic field noise
Move the digitizer away from such locations so it will work properly.
l The pointer cannot follow the digitizer pen movement if you move the digitizer pen too quickly.
23
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
23
2013/05/09
18:39:55
Handling and Maintenance
n When the battery indicator does not light on
The battery indicator may not light on even if the AC adaptor and the battery pack are correctly
connected to the computer, due to the following reasons.
l The AC adaptor’s protection function may be working. In this case, pull out the AC cord and
wait for more than 1 minute before reconnecting the AC cord.
n When using peripheral devices
Follow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction manuals of the peripheral devices.
l Use the peripheral devices conforming to the computer’s specifications.
l Connect to the connectors in the correct direction.
l If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of
pins, etc.
l If screws are included, fasten them securely.
l Remove the cables when you carry the computer. Do not pull the cables forcibly.
nPreventing your computer from unauthorized use via wireless LAN/Bluetooth/Wireless
WAN
<Only for model with wireless LAN/Bluetooth/Wireless WAN>
l Before using wireless LAN/Bluetooth/Wireless WAN, make the appropriate security settings
such as data encryption.
Useful Information
n Battery Recalibration
l The battery recalibration may take a long time due to the large battery capacity. This is not a
malfunction.
<When performing “Battery Recalibration” after shutting down Windows>
Ÿ Full charge: Approximately 2.5 hours
Ÿ Complete discharge: Approximately 3 hours
When performing “Battery Recalibration” without shutting down Windows, it may take more time to
charge / discharge.
nSensors
This computer is equipped with four sensors (acceleration sensor, gyro sensor, magnetic sensor,
ambient light sensor), and you can use these sensors with any software that is compatible.
As the accuracy of each sensor output is dependent on the operating environment and other conditions, the results should only be used as a reference.
The acceleration sensor, gyro sensor, and magnetic sensor are located at the bottom left of the
LCD. The detection results of each sensor may vary depending on how you are holding the computer, the application software you are using, and other factors.
l Automatic brightness adjustment
The computer is equipped with an automatic brightness adjustment function that adjusts the
display screen based on the ambient light sensor. You can configure the automatic adjustment
function as follows.
- [Change PC Settings] - [General] - [Screen] - [Adjust my
ADisplay “Charm” and touch
screen brightness automatically].
(Start) - [Control Panel] - [Hardware and Sound] - [Power Option].
ATouch
B Touch [Change plan settings] for the power plan currently used.
24
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
24
2013/05/09
18:39:55
Touch [Change advanced power settings] and double-touch [Display].
C
DDouble-touch [Enable adaptive brightness], make necessary settings, and touch [OK].
Set each item to ON, and the brightness of the screen display will adjust automatically.
The ambient light sensor is located at the top of LCD.
The ambient light cannot be detected properly if this area is obstructed or dirty.
l Magnetic sensor
The magnetic sensor on the computer operates by detecting geomagnetism. Therefore, the
magnetic sensor may not function properly and it readings may be inaccurate, especially in
the following environments.
Ÿ Inside or near steel structures such as buildings or bridges
Ÿ Inside or near automobiles, or near train power lines
Ÿ Near metallic furniture or appliances
Ÿ When the AC adaptor or other peripheral devices are brought closer to the computer
Ÿ Near magnets, speakers, or other objects with strong magnetic fields
The magnetic directions indicated by the magnetic sensor may not be accurate immediately
after purchase or in environments with poor magnetic fields.
In such cases, turn on the computer and move it as follows.
A Hold the computer so that its screen side is facing upward and level.
B While keeping the computer level, rotate it 90 degrees or more clockwise.
C Return the computer to position A, and rotate it 90 degrees or more counterclockwise.
D Return the computer to position A.
ETilt the computer 90 degrees or more to the left so that the left side of the computer tilts
down.
FReturn the computer to position A, and tilt it 90 degrees or more to the right so that the
right side of the computer tilts down.
CAUTION
Useful Information
●Hold the computer firmly when moving it. Strong shocks from dropping the computer may
result in damage.
25
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
25
2013/05/09
18:39:56
Handling and Maintenance
Maintenance
If drops of water or other stains get on the surface of the LCD panel, wipe them off immediately.
Failure to do so may result in staining.
To clean the LCD panel
Use the soft cloth included with the computer. (For further information, refer to “Suggestions
About Cleaning the LCD Surface” è
Reference Manual “Screen Input Operation”.)
To clean areas other than the LCD panel
Wipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted
detergent and wring it thoroughly.
CAUTION
l Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc. Do not use commercially-available household cleaners and cosmetics,
as they may contain components harmful to the surface.
l Do not apply water or detergent directly to the computer, since liquid may enter inside of the
computer and cause malfunction or damage.
To clean inside of the dust cover
Approximately once a month, clean up inside of the dust cover by the following procedure.
A Turn off the computer and remove the AC adaptor.
B Remove the battery pack.
C Remove the screw (A) and dust cover as illustrated below.
Useful Information
㪘
D Clean up inside of the dust cover.
E Set the dust cover, screw and battery pack.
26
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
26
2013/05/09
18:39:56
Installing Software
Installing software will return the computer to the default condition. When you install the software, the flash memory data will be erased.
Back up important data to other media or an external hard disk before installation.
CAUTION
l Do not delete the Recovery Partition on the flash memory. The disk space in the partition is
not available to store data.
To check the Recovery Partition, perform the following methods.
A
Open “Computer”. Long touch [Computer], then touch [Manage].
To open “Computer”, proceed as follows on the Start screen.
1. On the Start screen, flick from right side to inside of the screen.
2. Touch [All apps] on the toolbar.
3. Touch [Computer] under “Windows System”.
(Start) and long touch [Computer], then touch [Manage].
Touch
l A standard user needs to enter an administrator password.
B Touch [Disk Management].
1
Perform “Remove everything and reinstall Windows”.
2
3
When termination screen is displayed, touch [OK] to turn off the computer.
Turn on the computer.
4
5
6
7
Perform the “First-time Operation” ( page 20).
Start the Setup Utility and change the settings as necessary.
Perform Windows Update.
<Only for model with TPM> Clear TPM.
Useful Information
nFlash memory Recovery
You can reinstall the OS that was pre-installed at the time of purchase (Windows 8 or Windows 7).
Preparation
l Connect the external keyboard.
l Remove all peripherals.
l Connect the AC adaptor and do not remove it until installation is complete.
- [Change PC settings] - [General].
A Display “Charm” and touch
B Touch [Get Started] under “Remove everything and reinstall Windows”.
Installation starts according to the instructions on the screen. (It will take approximately
20 minutes.)
l Do not interrupt installation, for example by turning off the computer or performing other
operation.
Otherwise installation may become unavailable as Windows may not start up or the
data may be corrupted.
l If the password is requested, enter the Supervisor Password.
A On the Start screen, flick from bottom side to inside of the screen and touch [All apps]
on the toolbar.
B Touch [Run] under “Windows System”, input [tpm.msc] and touch [OK].
C Touch [Clear TPM ...] under “Actions” on the right of the “TPM Manager on Local Computer” screen.
27
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
27
2013/05/09
18:39:56
Installing Software
D Touch [Restart] of the “Manage the TPM security hardware” screen.
The computer will restart.
E When “TPM configuration change was requested to ...” is displayed, press F12.
Windows will start.
F When “TPM is ready” appears, touch [Close].
1
Turn on the computer, and press F2 or Del while [Panasonic] boot
screen is displayed.
The Setup Utility starts up.
l If the [Panasonic] boot screen is not displayed, turn on the computer while holding down
F2 or Del.
l If the password is requested, enter the Supervisor Password.
2
Write down all of the contents of the Setup Utility and press F9.
At the confirmation message, select [Yes] and press Enter.
3Press F10.
At the confirmation message, select [Yes] and press Enter.
Computer will restart.
4Press F2 or Del while [Panasonic] boot screen is displayed.
Useful Information
The Setup Utility starts up.
l If the password is requested, enter the Supervisor Password.
5
6
Select the [Exit] menu, then select [Recovery Partition] and press Enter .
Touch [Reinstall Windows] and touch [Next].
7
Touch [YES].
8
Touch [Yes, I agree to the provisions above and wish to continue!] and
touch [Next].
Select the setting and touch [Next].
9
The License Agreement screen appears.
The License Agreement screen appears.
l [Reinstall Windows to the whole Hard Disk to factory default.]
Select this option when you want to install Windows to the factory default. After installation, you can create a new partition. For how to create a new partition, refer to “To
change the partition structure” ( page 21).
*1
l [Reinstall to the System and OS partitions.]
Select this option when the flash memory has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” (
page 21).
You can keep the partition structure.
*1
This does not appear if Windows cannot be installed to the recovery partition and the area usable by Windows.
10 At the confirmation message, touch [YES].
11 Select OS (32bit or 64bit) and touch [OK].
12 At the confirmation message, touch [YES].
Installation starts according to the instructions on the screen. (It will take approximately 20
minutes.)
l Do not interrupt installation, for example by turning off the computer or pressing Ctrl +
Alt + Del.
28
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
28
2013/05/09
18:39:56
Otherwise installation may become unavailable as Windows may not start up or the
data may be corrupted.
13 When Ending process screen is displayed, touch [OK] to turn off the
computer.
14 Turn on the computer.
l If the password is requested, enter the Supervisor Password.
15 Perform the “First-time Operation” ( page 20).
16 Start the Setup Utility and change the settings as necessary.
17 Perform Windows Update.
n Using Recovery Disc
Use the Recovery Disc in the following conditions.
Ÿ You have forgotten the administrator password.
Ÿ Installation is not complete. The recovery partition in the flash memory may be broken.
<Only for Windows 7 downgrade model>
Ÿ
To change OS from Windows 7 to Windows 8, or vice versa.
NOTE
l
To change OS from 32 bit to 64 bit, or vice versa, install OS using the recovery
partition in the flash memory.
Useful Information
Preparation
l Prepare the following items:
Reference Manual “Recovery Disc Creation Utility”)
•Recovery Disc (
•USB DVD drive (optional) (refer to recent catalogs and other sources for information
about the products available)
l Remove all peripherals (except for the USB DVD drive).
l Connect the AC adaptor and do not remove it until installation is complete.
NOTE
l You can use the following buttons instead of the keyboard.
: F2 key (Default setting)
: ↓ key
: ↑ key
: Enter key
: Tab key
1
2
Connect the DVD drive to the USB port.
Start the Setup Utility.
- [Change PC settings] - [General].
A Display “Charm” and touch
B Touch [Restart now] under “Advanced startup”.
C Touch [Troubleshoot] - [Advanced options] - [UEFI Firmware Settings] - [Restart].
Turn on the computer, and touch top left of the screen while [Panasonic] boot screen is
displayed.
l If the [Panasonic] boot screen is not displayed, turn on the computer while touching top
left of the screen.
29
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
29
2013/05/09
18:39:56
Installing Software
l If the password is requested, enter the Supervisor Password.
3
Write down all of the contents of the Setup Utility and touch [Exit] and
double-touch [Load Default Values].
At the confirmation message, touch [Yes].
4
Check the [UEFI Boot] setting of the Setup Utility.
5
6
Set the Recovery Disc into the DVD drive.
Touch [Exit] and double-touch [Save Values and Reboot].
7
Touch top left of the screen while [Panasonic] boot screen is displayed.
[UEFI Boot] should be set to as follows.
When the recovery disc for Windows 8 is used: [Enabled]
When the recovery disc for Windows 7 is used: [Disabled]
At the confirmation message, touch [Yes].
Computer will restart.
The Setup Utility starts up.
l If the password is requested, enter the Supervisor Password.
8
9
Touch [Exit], then double-touch your DVD drive in [Boot Override].
Double-touch [Yes].
The computer will restart.
Useful Information
10 Touch [Reinstall Windows] and touch [Next].
At the confirmation message, touch [YES].
11
12 At the License Agreement screen, Touch [Yes, I agree to the provisions above and wish to continue!] and touch [Next].
13 When the recovery disc for Windows 8 is used, touch [Next].
When the recovery disc for Windows 7 is used, select the setting and
touch [Next].
l [Reinstall Windows to the whole Hard Disk to factory default.]
Select this option when you want to install Windows to the factory default. After installation, you can create a new partition. For how to create a new partition, refer to “To
change the partition structure” ( page 21).
l [Reinstall to the System and OS partitions.]*2
Select this option when the flash memory has already been divided into several partitions. For how to create a new partition, refer to “To change the partition structure” (
page 21).
You can keep the partition structure.
*2
This does not appear if Windows cannot be installed to the recovery partition and the area usable by Windows.
14 At the confirmation message, touch [YES].
Installation starts according to the instructions on the screen. (It will take approximately 30
- 45 minutes.)
l Do not interrupt installation, for example by turning off the computer.
Otherwise installation may become unavailable as Windows may not start up or the
data may be corrupted.
15 When Ending process screen is displayed, remove the Recovery Disc
and DVD Drive.
30
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
30
2013/05/09
18:39:56
16
Touch [OK].
Touch [OK] to turn off the computer.
17
The computer will restart.
Turn on the computer.
l If the password is requested, enter the Supervisor Password.
18 Perform the “First-time Operation” ( page 20).
19 Start the Setup Utility and change the settings as necessary.
20 Perform Windows Update.
<Only for model with TPM> Clear TPM ( page 27).
Useful Information
21
31
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
31
2013/05/09
18:39:56
Troubleshooting (Basic)
Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the “Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact Panasonic Technical Support (è page 47). You
can also check the computer’s status in the PC Information Viewer
(è
Reference Manual “Troubleshooting (Advanced)”).
n Starting Up
Cannot start up.
The power indicator or
battery indicator is not
lit.
The power is turned on
but “Warming up the
system” appears.
l Connect the AC adaptor.
l Insert a fully charged battery.
l If a device is connected to the USB port, disconnect the device, or
set [USB Port] or [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.
l If a device is connected to the ExpressCard slot, disconnect the
device, or set [ExpressCard Slot] to [Disabled] in the [Advanced]
menu of the Setup Utility.
Reference Manual “Setup Utill Turn off the concealed mode (è
ity”).
l Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot]
should be set to
[Enabled] /
[Disabled].
l The computer is warming up before start up. Wait for the computer to
start up (the maximum waiting time will be displayed on the screen).
If, “Cannot warm up the system” is displayed, the computer failed to
warm up and does not start. In this case, turn off the computer, leave
it in an environment of 5 °C {41 °F} or higher temperature for about an
hour, and then turn on the power again.
Cannot turn on the com- l Leave it in an environment of 5 °C {41 °F} or higher temperature for
about an hour, then turn on the power again.
puter.
The computer does not
resume from sleep.
(The battery indicator
blinks green and orange
alternately.)
Troubleshooting
You have forgotten the
password.
l Supervisor Password or User Password: Contact Panasonic Technical
Support (è page 47).
l Administrator password:
Ÿ If you have a password reset disk, you can reset the administrator
password. Set the disk and enter any wrong password, then follow
the on-screen instructions and set a new password.
Ÿ If you do not have a password reset disk, install (è page 27) and
set up Windows, and then set a new password.
“Remove disks or other l A floppy disk is in the drive and it does not contain system startup
information. Remove the floppy disk and press any key.
media. Press any key to
If a device is connected to the USB port, disconnect the device, or
l
restart” or a similar messet [USB Port] or [Legacy USB Support] to [Disabled] in the [Adsage appears.
vanced] menu of the Setup Utility.
l If the problem persists after removing the disk, it may be a flash memory failure. Contact Panasonic Technical Support (è page 47).
32
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
32
2013/05/09
18:39:57
n Starting Up
Windows startup and
operation is slow.
Reference Manual “Setup Utility”) to
l Start the Setup Utility (è
return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note
that the processing speed depends on the application software, so this
procedure may not make Windows faster.)
l If you installed a resident software after purchase, turn off the residence.
The date and time are
incorrect.
l Make the correct settings.
A Open the Control Panel.
1.On the Start screen, flick from bottom side to inside of the
screen.
2.Touch [All apps] on the toolbar.
3.Touch [Control Panel] under “Windows System”.
(Start) - [Control Panel].
Touch
B Touch [Clock, Language, and Region] - [Date and Time].
l If the problem persists, the internal clock battery may need to be replaced. Contact Panasonic Technical Support (è page 47).
l When the computer is connected to LAN, check the date and time of
the server.
l The 2100 A.D. or later year will not be correctly recognized on this
computer.
[Executing Battery
Recalibration] screen
appears.
l The Battery Recalibration was canceled before Windows was shut
down last time. To start up Windows, turn off the computer by the
power switch, and then turn on.
[Enter Password] does l Select [Enabled] in [Password On Resume] in the [Security] menu of
Reference Manual “Setup Utility”).
the Setup Utility (è
not appear when resumThe
Windows
password
can be used instead of the password set in
l
ing from sleep/hibernathe
Setup
Utility.
tion.
Troubleshooting
A Open the Control Panel.
1.On the Start screen, flick from bottom side to inside of the
screen.
2.Touch [All apps] on the toolbar.
3.Touch [Control Panel] under “Windows System”.
(Start) - [Control Panel].
Touch
B Touch [User Accounts and Family Safety] - [Add or remove user accounts].
C Touch [System and Security] - [Power Option] - [Require a password when the computer wakes] and add a check mark for [Require
a password].
33
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
33
2013/05/09
18:39:57
Troubleshooting (Basic)
n Starting Up
Cannot resume.
l One of the following operations may have been carried out. Press the
power switch to turn on the computer. Data not saved will be lost.
Ÿ In sleep mode, the AC adaptor or battery pack was disconnected, or
a peripheral was connected or disconnected.
Ÿ The power switch was pressed for four seconds or longer to forcibly
turn off the computer.
l An error may occur when the computer automatically enters the sleep
or hibernation mode while the screensaver is active. In this case, turn
off the screensaver or change the pattern of the screensaver.
Other startup problems. l Start the Setup Utility (è
Troubleshooting
Reference Manual “Setup Utility”) to return the Setup Utility settings (excluding the passwords) to the default
values. Start the Setup Utility and make the settings again.
l Remove all peripheral devices.
l Check to see if there was a disk error.
A Remove all peripheral devices including an external display.
B Open “Computer”.
1.On the Start screen, flick from bottom side to inside of the
screen.
2.Touch [All apps] on the toolbar.
3.Touch [Computer] under “Windows System”.
(Start) - [Computer].
Touch
C Long touch [Local Disk (C:)], and touch [Properties].
D Touch [Tools] - [Check Now...].
Ÿ A standard user needs to enter an administrator password.
E Select the option in [Check disk options] and touch [Start].
F Touch [Schedule disk check] and restart the computer.
l
Connect the external keyboard and start the computer in Safe Mode,
then check the error details. When the [Panasonic] boot screen disappears*1 at startup, press and hold F8 until the Windows Advanced
Options Menu is displayed. Select the Safe Mode and press Enter .
*1
When [Password on boot] is set to [Enabled] in the [Security] menu
of the Setup Utility, [Enter Password] appears after the [Panasonic]
boot screen disappears. As soon as you enter the password and press
Enter , press and hold F8.
n Entering Password
Even after entering the <Only if the external keyboard is connected>
password, password in- l The computer may be in ten-key mode.
lights, press NumLk to disable the tenIf the NumLk indicator
put screen is displayed
key mode, and then input.
again.
l The computer may be in Caps Lock mode.
lights, press Caps Lock to disable the
If the Caps Lock indicator
Caps Lock mode, and then input.
34
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
34
2013/05/09
18:39:57
n Entering Password
Cannot log on to Windows. (“The user name
or password is incorrect.” is displayed.)
l The user name (account name) includes an “@” mark.
- If another user account name exists:
Log on to Windows using another user account name, and delete the
account name that includes “@”. Then create a new account name.
- If no other account name exists:
You need to reinstall Windows (è page 27).
n Shutting down
Windows does not shut
down.
l Remove the USB device and the ExpressCard.
l Wait one or two minutes. It is not a malfunction.
nDisplay
No display.
l The external display is selected.
Flick from right side to inside of the screen, and touch
select the external display.
-
, then
A Long touch the desktop, and then touch [Graphic Properties].
B Select one of the application modes and touch [OK].
C Touch [Multiple Displays].
D Select the display in [Operating Mode].
E Touch [Apply].
F Touch [OK].
GIf necessary, touch [General Settings], set the color depth, resolution, etc., and touch [OK].
l When using an external display,
Ÿ Check the cable connection.
Ÿ Turn on the display.
Ÿ Check the settings of external display.
l The display is turned off by the power-saving function.
Touch the screen.
The screen is dark.
Troubleshooting
To resume, touch the screen.
l The computer entered sleep or hibernation by the power-saving function. To resume, press the power switch.
l The screen is darker when the AC adaptor is not connected. Open the
Dashboard for Panasonic PC and adjust the brightness. As you increase the brightness, battery consumption increases.
You can separately set the brightness for when the AC adaptor is connected and when not connected.
Reference Manual “Setup Utill Turn off the concealed mode (è
ity”).
35
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
35
2013/05/09
18:39:58
Troubleshooting (Basic)
nDisplay
The screen is disordered.
l Changing the number of display colors and resolution may affect the
screen. Restart the computer.
l Connecting/disconnecting an external display may affect the screen.
Restart the computer. Under factory default settings, the brightness of
the display screen will adjust automatically based on the ambient light
detected by the ambient light sensor. You can adjust the settings for
this sensor (è page 24).
l When using the Extended Desktop, use the same display colors for the
During Simultaneous
external display as those used by the LCD. If you continue to experidisplay, one of the
ence problems, try changing the display.
screens becomes disorLong touch on the desktop, and touch [Graphics Properties...] - [Disdered.
play].
l Simultaneous display cannot be used until Windows startup is complete (during Setup Utility, etc.).
l If the external display does not support the power saving function, it
The external display
may not work normally when the computer enters the power saving
does not work normally.
mode. Turn off the external display.
Cannot rotate the display.
lThe application program currently running may not support the image
rotation. Quit the program, and then try to rotate the image. This can
ameliorate the status.
lWhen the automatic rotation is off, screen display does not rotate automatically.
nScreen
l When using the external mouse, connect it correctly.
l Restart the computer using the external keyboard/mouse.
l If the computer does not respond to external keyboard/mouse commands, read “No response”
(è page 37).
Cannot point the correct position using the
included digitizer pen.
Reference Manual “Screen Input
l Perform the screen calibration (è
Operation” ).
l Use the included pen.
l On the Windows logon screen or the Welcome screen, you may not be
able to point the correct position using the included digitizer pen. Use
the external keyboard or the external mouse to log on.
l You may not be able to point the correct position using your finger after
resuming from sleep or hibernation while the display is rotated.
If this is the case, proceed as follows.
A
1.On the Start screen, flick from bottom side to inside of the
screen, and touch [All apps] on the toolbar.
2.Touch [Run] under “Windows System”, input [c:\util\resset\resset.
exe] and touch [OK].
(Start) and input “c:\util\resset\resset.exe” in [Search pro Touch
grams and files], then press Enter .
B Touch [Yes] on the [User Account Control] screen.
C Select [Disabled] and touch [OK].
D Touch [Yes] when you are prompted to restart the computer.
Troubleshooting
The pointer does not
work.
36
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
36
2013/05/09
18:39:58
nScreen
Cannot display “Charm” l Delete the calibration data.
A Start Dashboard for Panasonic PC and touch [Basic] - [Touch Calior difficult to display
bration].
“Charm”.
B Touch [Reset…] and follow the on-screen instructions.
n On-screen Document
The document of PDF
format is not displayed.
l Install Adobe Reader.
A Log on to Windows as an administrator.
(Start) and input “c:\util\reader\Pinstall.bat” in [Search
BTouch
Programs and files] then press Enter .
C Update Adobe Reader to its latest version.
If your computer is connected to the internet, start up Adobe Reader and touch [Help] - [Check for Updates...].
nOthers
No response.
Troubleshooting
l Open Task Manager and close the software application that is not
responding.
l An input screen (e.g., password input screen at startup) may be hidden behind another window. Touch the application icons at the bottom
of the screen to check.
l Press the power switch for four seconds or longer to shut down the
computer, and then press the power switch to turn it on. If the application program does not work normally, uninstall and reinstall the program. To uninstall,
A Open the Control Panel.
1.On the Start screen, flick from bottom side to inside of the
screen.
2.Touch [All apps] on the toolbar.
3.Touch [Control Panel] under “Windows System”.
(Start) - [Control Panel].
Touch
BTouch [Program] - [Uninstall a program].
The recovery disc for l Perform recovery using the recovery disc for Windows 7 first, and then
perform recovery using the recovery disc for Windows 8.
Windows 8 in not functioning.
Cannot connect to a
network.
l Set the device ([Wireless LAN] / [Bluetooth] / [Wireless WAN] of [Wireless Configuration]) to [Enabled] in the [Advanced] menu of the Setup
Utility (Wireless Configuration).
- [Change PC Settings] - [Wireless]. Set
l Display “Charm” and touch
[Airplane mode] to [Off], and then;
set [Wi-Fi] in “Wireless device” to [On] (for wireless LAN).
set [Mobile broadband] in “Wireless device” to [On] (for wireless WAN).
set [GPS] in “Wireless device” to [On] (for wireless WAN).
set [Bluetooth] in “Wireless device” to [On] (for Bluetooth).
37
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
37
2013/05/09
18:39:58
LIMITED USE LICENSE AGREEMENT
THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”) ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED
BY YOU ONLY IN ACCORDANCE WITH THE LICENSE TERMS DESCRIBED BELOW. YOUR
USE OF THE PROGRAMS SHALL BE CONCLUSIVELY DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.
Panasonic Corporation has developed or otherwise obtained the Programs and hereby licenses
their use to you. You assume sole responsibility for the selection of the Product (including the
associated Programs) to achieve your intended results, and for the installation, use and results
obtained therefrom.
LICENSE
A. Panasonic Corporation hereby grants you a personal, non-transferable and non-exclusive
right and license to use the Programs in accordance with the terms and conditions stated in
this Agreement. You acknowledge that you are receiving only a LIMITED LICENSE TO USE
the Programs and related documentation and that you shall obtain no title, ownership nor any
other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership and rights shall remain with Panasonic Corporation or
its suppliers.
B. You may use the Programs only on the single Product which was accompanied by the Programs.
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distribute or otherwise make the Programs or related documentation
available to any third party, by time-sharing or otherwise, without the prior written consent of
Panasonic Corporation.
D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related
documentation for any purpose, except that you may make one (1) copy of the Programs for
backup purposes only in support of your use of the Programs on the single Product which was
accompanied by the Programs. You shall not modify, or attempt to modify, the Programs.
E. You may transfer the Programs and license them to another party only in connection with your
transfer of the single Product which was accompanied by the Programs to such other party.
At the time of such a transfer, you must also transfer all copies, whether in printed or machine
readable form, of every Program, and the related documentation, to the same party or destroy
any such copies not so transferred.
F. You may not remove any copyright, trademark or other notice or product identification from the
Programs and you must reproduce and include any such notice or product identification on
any copy of any Program.
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.
Appendix
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY
COPY THEREOF, IN WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY,
EXCEPT AS PERMITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY
TERMINATED.
38
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
38
2013/05/09
18:39:58
TERM
This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate this license at any time by destroying, at your expense, the Programs and
related documentation together with all copies thereof in any form. This license will also terminate
effective immediately upon occurrence of the conditions thereof set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any such termination, you agree to destroy, at your expense, the Programs and related documentation together
with all copies thereof in any form.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND
AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT
IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE AGREEMENT BETWEEN US,
WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT, ORAL OR WRITTEN, AND
ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MATTER OF
THIS AGREEMENT.
Appendix
GOVERNMENT RESTRICTED RIGHTS.
The Software is provided with “RESTRICTED RIGHTS.” Use duplication or disclosure by the
government is subject to restrictions as set forth in FAR52.227-14 and DFAR252. 227-7013 et
seq. or their successors.
Use of the Software by the government constitutes acknowledgement of Intel’s proprietary rights
therein.
Contractor or Manufacturer is Intel Corporation, 2200 Mission College Blvd., Santa Clara, CA
95052.
39
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
39
2013/05/09
18:39:58
Contrat de licence d’usage limité
Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles cidessous. En utilisant les logiciels, vous vous engagez de
manière définitive à respecter les termes, clauses et conditions des présentes.
Panasonic Corporation a mis au point ou obtenu les Logiciels et vous en concède l’utilisation
par les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des
Logiciels associés) pour obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation
et des résultats obtenus.
Licence
A. Panasonic Corporation vous octroie par les présentes le droit et la licence personnels, non
cessibles et non exclusifs d’utiliser les Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit limité d’utiliser les Logiciels et
la documentation les accompagnant et vous vous engagez à
n’obtenir aucun droit de titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la
documentation les accompagnant ni vis-à-vis des algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les Logiciels et la documentation les accompagnant, dont les titres, propriété et droits resteront tous à
Panasonic Corporation ou à leurs propriétaires.
B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les
Logiciels.
C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous
ne pouvez ni distribuer ni mettre les Logiciels et la documentation les accompagnant à la
disposition d’un tiers, par partage de temps ou de quelque autre manière que ce soit, sans
l’autorisation écrite préalable de Panasonic Corporation.
D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels
ni de la documentation les accompagnant pour quelque fin que ce soit, à l’exception d’une (1)
copie des Logiciels à des fins de sauvegarde uniquement pour soutenir votre utilisation des
Logiciels sur le Produit unique qui est accompagné par les Logiciels. Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.
E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport
avec votre cession du Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez céder également toutes les copies, que ce soit
sous forme imprimée ou lisible par la machine, de tous les Logiciels ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.
F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni
aucune identification de produit des Logiciels et vous devez reproduire et inclure toutes ces
notices ou identifications de produit sur toutes les copies des Logiciels.
Appendix
Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni
aucune de leurs copies, de façon électronique ou mécanique, en tout ou en partie.
Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies,
en tout ou en partie, à l’exception de ce qui est expressément stipulé dans ce contrat.
Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de
ce qui est autorisé au paragraphe E ci-dessus, votre licence est automatiquement résiliée.
40
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
40
2013/05/09
18:39:58
Termes, clauses et conditions
Cette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à
moins d’une résiliation antérieure. Vous pouvez résilier cette licence à tout moment en détruisant,
à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous
quelque forme que ce soit. Cette licence sera également résiliée, avec application immédiate, si
les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation,
vous acceptez de détruire, à vos frais, les Logiciels et la documentation les accompagnant avec
toutes leurs copies, sous quelque forme que ce soit.
Appendix
Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de
respecter ses termes, clauses et conditions. Vous reconnaissez en outre qu’ils sont la description
complète et exclusive du contrat conclu entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre communication entre nous, relativement à
l’objet du présent contrat.
41
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
41
2013/05/09
18:39:58
Specifications
This page provides the specifications for the basic model.
The model number is different according to the unit configuration.
l To check the model number:
Check the bottom of the computer or the box the computer came in at the time of purchase.
l To check CPU speed, memory size and the flash memory drive size:
Reference Manual “Setup Utility”) and select [Information] menu.
Run the Setup Utility (è
[Processor Speed]: CPU speed, [Memory Size]: Memory size, [Hard Disk]: Flash Memory
drive size
n Main Specifications
Model No.
FZ-G1AAAZXBM
CPU
Intel®® Core™ i5-3437U Processor (3 MB*1 cache, up to 2.9 GHz) with
Intel Turbo Boost Technology
Chipset
Mobile Intel® QM77 Express Chip set
Video controller
Built-in Chip Set
Memory*1*2
4 GB
Video Memory*1*3
UMA 1664 MB Max.
UMA <32-bit> 1544 MB Max. <64-bit> 1696 MB
Storage*4
Flash memory drive : 128 GB
Approx. 10 GB is used as a partition with HDD recovery tools. (Users
cannot use this partition.)
Approx. 1 GB is used as a partition with system tools. (Users cannot use
this partition.)
Approx. 20 GB is used as a partition with HDD recovery tools. (Users
cannot use this partition.)
Approx. 300 MB is used as a partition with system tools. (Users cannot
use this partition.)
Display Method
10.1 WUXGA type
Internal LCD*5
65,536/16,777,216 colors (1920 × 1200 dots)
External Display (HDMI)
Wireless LAN
*6
*7
Intel® Centrino® Advanced-N 6235 (è page 44)
Bluetooth*8
Wireless WAN
LAN
è page 44
*9
Sierra Wireless™ High-speed module
*10
IEEE 802.3 10Base-T/IEEE 802.3u 100Base-TX/IEEE 802.3ab
1000Base-T
Sound
WAVE and MIDI playback, Intel® High Definition Audio subsystem support, Monaural speaker
Security Chip
TPM (TCG V1.2 compliant)*11
Camera
Front
Rear
Appendix
65,536/16,777,216 colors (1920 x 1200 dots Max.)
Sensor
*12
1280 × 720 dots, 30 fps (Video), Monaural Microphone
1280 × 720 dots, 30 fps (Video) / 2048 x 1536 dots (Still)
Ambient light
sensor
Magnetic sensor
Equipped
Gyro sensor
Acceleration
sensor
42
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
42
2013/05/09
18:39:59
n Main Specifications
Card Slot
Smart Card*13
x1
micro SD
Memory
Card*14
x1
Interface
USB port 3.0 x 1, 2.0 x 1*15, Serial Port (Dsub 9-pin male)*16, LAN port
(RJ-45)*10, HDMI Port (Type A)*17, Expansion Bus Connector, Headset
(Miniature jack, 3.5 DIA / Headphone: Impedance 32 Ω, Output Power 4
mW × 2,Stereo / Microphone: Monaural Input)*18
Pointing Device
Digitizer + Multi touch (Capacitive) (Anti-Reflection, Digitizer pen (included) touch capable)
Power Supply
AC adaptor or Battery pack
AC Adaptor
*19
Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 16 V DC, 4.06 A
Li-ion 10.8 V, 4400 mAh (typ.), 4100 mAh (min.)
Battery Pack
Operating Time*20
Charging
Time*21
Approx. 8 hours
Power on
Approx. 3 hours
Power off
Approx. 2.5 hours
Power Consumption*22
Approx. 30 W*23 / Approx. 60 W
(maximum when recharging in the ON state)
Physical Dimensions (W × D ×
H)
270 mm × 188 mm × 19 mm
{10.6 " × 7.4 " × 0.75 "}
Weight
Approx. 1.1 kg {Approx. 2.5 lb.}
Operating
Environment
Storage
Temperature
-10 °C to 50 °C {14
°F to 122 °F}
(IEC60068-2-1, 2)*24
Humidity
30% to 80% RH (No condensation)
Temperature
-20 °C to 60 °C {-4 °F to 140 °F}
Humidity
30% to 90% RH (No condensation)
nSoftware
Windows® 8 Pro 64-bit
Installed OS*25
Windows® 8 Pro 64-bit
Windows ® 7 Professional 32-bit Service
Pack 1 / Windows ® 7
Professional 64-bit Service Pack 1
Windows ® 7 Professional 32-bit Service
Pack 1 (downgraded to
Windows ® 7) *26 / Windows ® 7 Professional
64-bit Service Pack 1
(downgraded to Windows® 7)*26
Windows ® 7 Professional 32-bit Service
Pack 1 / Windows ® 7
Professional 64-bit Service Pack 1
Appendix
Base OS
43
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
43
2013/05/09
18:39:59
Specifications
nSoftware
Pre-installed Software*25
Adobe Reader, PC Information Viewer, Battery Recalibration Utility, Hand
Writing Utility, Infineon TPM Professional Package*11 *27, Dashboard for
Panasonic PC, Recovery Disc Creation Utility, Power Plan Extension
Utility, Camera Utility, Manual Selector, Bluetooth Stack for Windows by
TOSHIBA
Wireless Manager 6.0*27 Wireless Manager 5.5f *27 *28, Wireless Switch
*28
Utility, Wireless Connection Disable Utility *27,
, Wireless Toolbox,
Camera for Panasonic Quick Boot Manager, Software Keyboard
PC
Aptio Setup Utility, PC-Diagnostic Utility, Hard Disk Data Erase Utility*29
*7
n Wireless LAN
Data Transfer Rates
IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*30
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)*30
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)*30
IEEE802.11n*31:
(HT20)GI*32 = 400ns: 150/130/115/86/72/65/57/43/28/21/14/7 Mbps
(automatically switched)*30
GI*32 = 800ns: 130/117/104/78/65/58/52/39/26/19/13/6 Mbps
(automatically switched)*30
(HT40)GI*32 = 400ns: 300/270/240/180/150/135/120/90/60/45/30/15
Mbps (automatically switched)*30
GI*32 = 800ns: 270/243/216/162/135/121/108/81/54/40/27/13
Mbps (automatically switched)*30
Standards Supported
IEEE802.11a / IEEE802.11b / IEEE802.11g / IEEE802.11n
Transmission method
OFDM system, DSSS system
Wireless Channels Used
IEEE802.11a : Channels 36/40/44/48/52/56/60/64/100/104/108/112/116/1
20/124/128/132/136/
140/149/153/157/161/165
IEEE802.11b / IEEE802.11g : Channels 1 to 11
IEEE802.11n : Channels 1-11/36/40/44/48/52/56/60/64/100/104/108/112/
116/120/124/128/132/136/140/149/153/157/161/165
RF Frequency Band
IEEE802.11a : 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7 GHz, 5.745 GHz - 5.825
GHz
IEEE802.11b / IEEE802.11g : 2.412 GHz - 2.462 GHz
IEEE802.11n :2.412 GHz - 2.462 GHz, 5.18 GHz - 5.32 GHz, 5.5 GHz - 5.7
GHz, 5.745 GHz - 5.825 GHz
*8
nBluetooth
Bluetooth Version
4.0
Appendix
Classic mode / Low Energy mode
Transmission method
FHSS system
Wireless Channels Used
Channels 1 to 79 / Channels 0 to 39
RF Frequency Band
2.402 GHz - 2.480 GHz
1 MB = 1,048,576 bytes/1 GB = 1,073,741,824 bytes
Memory size of the factory default depends on the model.
*3
A segment of the main memory is allotted automatically depending on the computer’s operating status.
The size of the Video Memory cannot be set by the user.
*4
1 MB = 1,000,000 bytes / 1 GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.
*5
A 16,777,216 color display is achieved by using the dithering function.
*1
*2
44
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
44
2013/05/09
18:39:59
*6
Selectable resolution depends on the specifications of the external display. Display may be impossible
using some connected external displays.
*7
Only for model with wireless LAN.
*8
Only for model with Bluetooth.
*9
Only for model with wireless WAN.
The specifications may differ depending on the models.
*10
Only for model with LAN.
*11
Only for model with TPM.
For information on TPM,
on the Start screen, touch the [Manual Selector] tile, and select
Double-touch [Manual Selector]
“Installation Manual for Trusted Platform Module (TPM)” /
on the desktop, and select “Installation Manual for Trusted Platform Module (TPM)”.
*12
Only for model with Rear Camera.
*13
Only for model with Smart Card slot.
*14
Only for model with micro SD memory card slot.
Operation has been tested and confirmed using Panasonic micro SD Memory Card with a capacity of
up to 2 GB, Panasonic micro SDHC Memory Card with a capacity of up to 32 GB, and Panasonic micro
SDXC Memory Card with a capacity of up to 64 GB.
Operation on other SD equipment is not guaranteed.
*15
Does not guarantee operation of all USB-compatible peripherals.
USB 2.0 port : Only for model with USB 2.0 port
*16
Only for model with serial port. To connect the serial device, the serial conversion cable (included) is necessary.
*17
Does not guarantee operation of all HDMI-compatible peripherals.
*18
Applicable plug for headsets are as follows.
Headphone R
Headphone L
GND
Mono Mic
*19
Appendix
<Only for North America>
The AC adaptor is compatible with power sources up to 240 V AC adaptor.
This computer is supplied with a 125 V AC compatible AC cord.
20-M-1-1
2
*20
Measured at LCD brightness: 60 cd/m
Varies depending on the usage conditions, or when an optional device is attached.
*21
Varies depending on the usage conditions.
*22
Approx. 0.5 W when the battery pack is fully charged (or not being charged) and the computer is OFF.
<When using with 115 V AC>
Even when the AC adaptor is not connected to the computer, power is consumed (Max. 0.3 W) simply by
having the AC adaptor plugged into an AC outlet.
*23
Rated power consumption 23-E-1
*24
Do not expose the skin to this product when using the product in a hot or cold environment. (è page 5)
When using in hot or cold environment, some peripherals and battery pack may fail to work properly.
Check the operation environment of the peripherals.
Using this product continuously in a hot environment will shorten the product life. Avoid use in these
types of environments.
When using in low temperature environment, startup may become slow or battery operation time may
become short. The computer consumes power when the flash memory is warming up during startup.
Therefore, if you are using battery power and the remaining power is low, the computer may not start up.
*25
Operations of this computer are not guaranteed except for the pre-installed OS and the OS which is
installed by using the flash memory recovery and the recovery disc.
*26
This system is preinstalled with Windows® 7 Professional software and also comes with a license for
Windows 8 Pro software. You may only use one version of the Windows software at a time. Switching
between versions will require you to uninstall one version and install the other version.
*27
Must be installed before use.
*28
For information on Wireless Manager, refer to the supplementary instructions by the following procedure.
AOn the Start screen, flick from bottom side to inside of the screen and touch [All apps] on the toolbar.
BTouch [Run] under “Windows System”, input “c:\util\wlprjct\Supplementary Instructions.pdf” then touch [OK].
Touch
(Start) and input “c:\util\wlprjct\Supplementary Instructions.pdf” in [Search programs and files] and press Enter .
45
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
45
2013/05/09
18:39:59
Specifications
*29
Perform on the recovery disc.
Alternatively perform on the flash memory recovery.
It does not correspond to IEEE802.11a+b+g+n standards.
Actual speeds may differ.
*31
Available when set to “WPA-PSK”, “WPA2-PSK” or “none”.
*32
Only available when HT40 enabled by the computer and access point which associated supports HT40.
Appendix
*30
46
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
46
2013/05/09
18:39:59
LIMITED WARRANTY
For U.S.A.
Panasonic System Communications Company of North America (PSCNA)
Computer Products - Worldwide Warranties
Section 1: Limited Warranty - Hardware
PSCNA, referred hereafter as “Panasonic” will repair the products listed below with new or rebuilt parts, free
of charge in a Global Panasonic designated service location for the period specified below from the date of
original purchase in the event of a defect in materials or workmanship. These warranties are extended solely
to the original purchaser. A purchase receipt or other proof of date of original purchase will be required
before warranty performance is rendered.
• Laptop PC (CF-##) – 3 Years
• Tablet PC (FZ-##) – 3 Years
• Ultra-Mobile (CF-U#/CF-H# Series) – 3 Years
• PDRC - LCD & Keyboard Assembly – 3 Years
Battery Warranty
Batteries supplied with the product are covered under the warranty for one (1) year from date of purchase,
except as excluded in Section 3. Batteries purchased separately are covered under the warranty for one (1)
year from the date of purchase. A replacement battery furnished under the product warranty is covered for
the remaining period of the one year warranty on the original or purchased battery.
Optional: Panasonic “Protection Plus” Warranty
Any unit for which the Panasonic “Protection Plus” warranty has been purchased will receive additional
coverage for any failure that occurs due to accidental damage. All other terms and conditions of the
standard warranty apply and this additional coverage will exist for the duration of the standard warranty
period of the unit. If an extended Protection Plus warranty program is purchased, coverage is extended to
the end of the last year of extended coverage purchased.
This warranty does not cover failures or defects that are caused by fire, intentional acts, loss, theft, improper
maintenance, modification or service by anyone other than the Panasonic National Service Center or a
Panasonic Authorized Service Provider, or damage that is attributable to acts of God. Cosmetic damage
that does not affect functionality is not covered. Cosmetic damage on units with hardware failures will be
repaired in accordance with the warranty terms. This warranty is extended solely to the original purchaser
on the unit serial number for which it was purchased. Complete unit replacement fulfills the full obligation
and is at the discretion of Panasonic and is limited to once during the coverage term. Maximum benefit is
limited to one replacement per coverage year of the Motherboard, LCD, Storage Drive, and Keyboard.
Wireless Module Warranty
Panasonic approved wireless modems installed in Panasonic brand computers and integrated by Panasonic
or an Authorized Panasonic Wireless Integrator are covered under the warranty for the remaining warranty
period of the device in which the modem is installed. For devices with less than three (3) months remaining
on the unit warranty, the wireless modem will be covered for a period of three (3) months from the date of
installation of the modem, covering only modem replacement or modem installation related issues.
All modems must be approved by the wireless carrier prior to use. Any use or attempted use of a wireless
modem not approved and activated by the carrier for use on their network is strictly prohibited and is not
sanctioned or warranted by Panasonic and may result in legal action. In addition, all modems must be approved
by Panasonic as compatible with the device hardware before installation or use.
Appendix
Panasonic’s sole responsibility for the warranty or technical support of the software required to install or
operate the modem is defined in Section 2 (Limited Software Warranty). Any attempted software installation
by anyone other than a Panasonic Authorized Wireless Integrator is not covered under warranty and may
result in service charges to re-image or replace the hard drive.
Installation or attempted installation by any party other than Panasonic or an Authorized Panasonic Wireless
Integrator is strictly not covered under the warranty and may void the computer warranty if damage results.
Options and Accessories Warranties
The below listed Panasonic brand or supplied options and accessories are covered under this limited
warranty for the period specified from the date of purchase or as specifically stated:
47
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
47
2013/05/09
18:39:59
LIMITED WARRANTY
•
•
•
•
•
•
•
•
•
•
•
•
•
AC Adaptor / Power Cord – 3 Years
Memory Expansion Card (Panasonic Brand) – 3 Years
Car Mount - Docking Station PCB or Vehicle Docking Station – 3 Years
Desktop Port Replicator, I-O Box, Docking Cradle (like CF-U1) – 3 Years
Antenna Pass-through Cable – 3 Years
Backlit or Full-sized keyboard - 3 Years or assumes warranty of the unit in which it is installed
Integrated Panasonic supplied options and kits including, but not limited to Wireless Modems, Media
Bay Drives (Floppy, CD, DVD, Combo), Camera, GPS, Bluetooth, Smartcard Reader, Magnetic Card
Reader, Barcode Scanner, and Fingerprint Reader - 3 Years or assumes warranty period of the unit in
which it is installed provided the integration was performed by Panasonic or an Authorized Integrator.
Hard Drive / Solid State Drive (Internal) - 3 Years
Separately purchased 2nd Hard Drive – 1 Year
External USB Drives (CD / DVD / Floppy / Hard Drive) – 1 Year
Optional Battery – 1 Year
Battery Charger / Multi-Bay Battery Charger – 1 Year
Stylus Pens, Digitizer & Standard - 90 Days (physical damage excluded)
Section 2 - Limited Warranty - Software
Panasonic warrants to you only that the disk(s) or other media on which the Programs are furnished will
be free from defects in material and workmanship under normal use for a period of sixty (60) days from the
date of delivery thereof to you, as evidenced by your purchase receipt..
This is the only warranty Panasonic makes to you. Panasonic does not warrant that the functions contained
in the Programs will meet your requirements or that the operation of the Programs will be uninterrupted
or error free. Panasonic shall have no obligation for any defects in the disk(s) or other media on which
the Programs are furnished resulting from your storage thereof, or for defects that have been caused by
operation of the disk(s) or other media
Panasonic’s entire liability and your exclusive remedy under this warranty shall be limited to the
replacement, in the United States or other Panasonic designated location, of any defective disk or other
media which is returned to Panasonic’s Authorized Service Center, together with a copy of the purchase
receipt, within the aforesaid warranty period.
Section 3 - Limited Warranty Exclusions - Specifically excluded from the warranty are:
Appendix
• All consumable items; such as screen protection films, logo badges, labels, cleaning cloths, carry
cases, manuals, cables, straps, belts, holsters, tethers, and harnesses and any other options and
accessories not listed above or covered under a separate warranty.
• Failures related to the product operating system, hard drive or solid state drive image, software setup,
software program, virus, other program(s) or file(s) on any drive or in any computer memory location.
• Failures due to BIOS settings or changes, as well as any cosmetic or physical damage to the unit.
• Any unit or device with a missing or altered model number or serial number label
• Cosmetic damage or any damage which occurs in shipment
• Failures which are caused by products not supplied by Panasonic
• Failures which result from alteration, accident, misuse, introduction of liquid or other foreign matter into
the unit, abuse, neglect, installation, maladjustment of consumer controls, improper maintenance or
modification, use not in accordance with product use instructions
• Failures due to service by anyone other than a Panasonic Authorized Service Provider
• Failures caused by improper installation of options or accessories or due to integration by any
company other than Panasonic or a Panasonic Authorized Integrator
• Damage, failure, or loss due to the unit being stolen, lost, misplaced, or used by anyone other than the
original purchaser
• Damage that is attributable to acts of God
This limited warranty only covers failures due to defects in materials or workmanship which occur during
normal use. If a unit is sent to a Panasonic Authorized Service Center and no hardware failure is found,
the customer will be billed for labor to correct a software issue or reimage the hard drive plus shipping and
applicable administrative fees at the current rates set by the service provider.
THIS PRODUCT IS NOT INTENDED FOR USE AS OR PART OF NUCLEAR EQUIPMENT/SYSTEMS,
48
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
48
2013/05/09
18:39:59
AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*1.
PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS
PRODUCT ARISING OUT OF THE FOREGOING USES.
*1 AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include class 2 Electronic Flight Bag (EFB) Systems and
Class 1 EFB Systems when used during critical phases of flight (e.g., during take-off and landing) and/or
mounted onto the aircraft. Class 1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory
Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No. 36.
Other Limits and Exclusions: There are no other express warranties except as listed above.
PANASONIC SHALL NOT BE LIABLE FOR LOSS OF DATA OR OTHER INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF
ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO
THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or
limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so
the above limitations or exclusions may not apply to you.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
For technical support or to arrange for service on your Panasonic computer product, call our toll-free hotline
at 1-855-PSC-TECH (855-772-8324).
Appendix
DIAL TOLL FREE: 1-855-PSC-TECH (855-772-8324)
Web Site : www.panasonic.com/toughbook
49
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
49
2013/05/09
18:39:59
LIMITED WARRANTY (GARANTIE LIMITÉE)
For Canada
PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY
Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, this computer product (excluding software media), when purchased from PCI or from a PCI authorized reseller, to be free from
defects in materials and workmanship under normal use, subject to the terms set forth below, during the
period of warranty coverage specified.
Scope of Coverage
Period of Coverage Type of Failure
Coverage
• Laptop Computers (except Battery) and AC Adaptor
• Factory/PCI installed options including Wireless WAN,
GPS, Bluetooth, Finger print reader, Backlit keyboard,
Memory Card and Media Bay Drives (Floppy, CD/DVD)
• Mobile Wireless Display
• PDRC – LCD and Keyboard Assemblies
• Port Replicator
Three (3) Years from
Date of Original End
User Customer Purchase
• Hand-held Computers
•Battery
• Battery charger
• Auto Adaptor
• External USB Drives
One (1) Year from Date Defective Materials or
of Original End User
Workmanship
Customer Purchase
• Digitizer pen or stylus
Ninety (90) Days from
Date of Original End
User Customer Purchase
Defective Materials or
Workmanship
Defective Materials or
Workmanship
• All consumable items including protection film, cleaning No Coverage
cloth, carry case, tether and harness
Remedy – In the event of a warranty claim, contact PCI’s representatives within the applicable warranty
period, identifying the nature of the defect claimed, at 1-800-668-8386 between 9:00 A.M. and 5:00 P.M.,
Eastern Time Zone, Mon. – Fri. (excluding holidays) for instructions on how to obtain service. A purchase
receipt or other proof of date of original purchase is required before warranty service is performed. Defective
parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts on
an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the
balance of the original period of warranty coverage.
No Coverage – This Limited Warranty does not cover products purchased outside Canada. Neither does
it cover damage to, failure of, or defects in a product or accessory through mishandling, improper installation, abnormal use, misuse, neglect, accident, introduction of liquid or other foreign matter into the product,
alteration or servicing by anyone not authorized by PCI, or act of God.
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS,
AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*2.
PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS
PRODUCT ARISING OUT OF THE FOREGOING USES.
*2
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and
Class1 EFB Systems when used during critical phases of flight (e.g., during take-off and landing) and/or
mounted on to the aircraft. Class1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory
Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36
IF YOU SHIP THE PRODUCT FOR WARRANTY SERVICE
Carefully pack the product, preferably in the original carton. Include details of defect claimed and proof of
date of original purchase. No liability is assumed for loss or damage to the product while in transit, if you
chose your own transportation carrier.
SOFTWARE MEDIA LIMITED WARRANTY
Appendix
Coverage – PCI warrants to you, the first end user customer, that the disk(s) or other media on which software program(s) is/are supplied will be free from defects in materials and workmanship under normal use in
Canada for a period of sixty (60) days from date of receipt as evidenced by your purchase receipt for your
Panasonic Computer product.
THIS IS THE ONLY WARRANTY THAT PCI MAKES RESPECTING THE SOFTWARE MEDIA. PCI does not
warrant the software. Please refer to the software licensor’s written warranty (accompanying the copy of the
software) for any software warranty claim.
Claim Procedure – In the event of a defect in material or workmanship in the media during the sixty (60)
day warranty period, and you return it, transportation costs prepaid, to Panasonic Canada Inc., Computer
50
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
50
2013/05/09
18:40:00
Products Marketing, 5770 Ambler Drive, Mississauga, Ontario L4W 2T3, within the warranty period, together
with a copy of your purchase receipt, and an explanation of the suspected defect, PCI will replace in Canada
the defective disk(s) or other media.
Remedy – PCI’s entire liability, and your only remedy for any breach of this software media warranty is limited to replacement of the media only. It does not cover any other damages, including, but not limited to, loss
of use or profit loss, or special, indirect or consequential damages, or other claims, whether or not of similar
character.
No Coverage – This limited warranty does not apply if the disk(s) or other media has been used in other
than a Panasonic product, or in environmental conditions other than those specified by PCI or the manufacturer, or if subjected to misuse, neglect, mishandling, modification or attempted modification of the program,
or if damaged by accident or act of God. PCI is not responsible for damage to or loss of any program, data
or removable storage media.
GENERAL
Appendix
NO OTHER WARRANTIES – PCI DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE SOFTWARE, SOFTWARE MEDIA,
COMPUTER PRODUCT, OPTIONS AND ACCESSORIES.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES – IN NO EVENT SHALL PCI BE LIABLE FOR ANY
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING FROM ANY BREACH OF THE LIMITED
WARRANTIES SET OUT IN THIS DOCUMENT, OR FROM THE USE OF THE COMPUTER PRODUCT,
INCLUDING, WITHOUT LIMITATION, LOSS OF DATA, BUSINESS, PROFIT OR GOODWILL.
IN ANY EVENT, PCI’S MAXIMUM LIABILITY FOR ANY BREACH SHALL NOT EXCEED THE AMOUNT
ACTUALLY PAID BY YOU FOR THE COMPUTER PRODUCT.
NO ACTION, REGARDLESS OF ITS BASIS, MAY BE BEGUN AGAINST PCI MORE THAN TWO (2)
YEARS AFTER THE CAUSE OF ACTION AROSE.
Statutory Warranties – Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.
51
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
51
2013/05/09
18:40:00
LIMITED WARRANTY
For Australia
Personal / Notebook Computers - 36 Month Warranty from Date of Purchase
1.Subject to the conditions of this warranty Panasonic or it’s Authorised Service Centre will perform
necessary service on the product without charge for parts or labour, if in the opinion of Panasonic, the
product is found to be faulty within the warranty period.
2.This warranty only applies to Panasonic products purchased in Australia and sold by Panasonic
Australia or its Authorised Distributors or Dealers and only where the products are used and serviced
within Australia or it's territories. Warranty cover only applies to service carried out by a Panasonic
Authorised Service Centre and only if valid proof of purchase is presented when warranty service is
requested.
3.This warranty only applies if the product has been installed and used in accordance with the
manufacturer’s recommendations (as noted in the operating instructions) under normal use and
reasonable care (in the opinion of Panasonic). The warranty covers normal domestic use only and does
not cover damage, malfunction or failure resulting from use of incorrect voltages, incorrect installation,
accident, misuse, neglect, build-up of dirt or dust, abuse, maladjustment of customer controls, mains
supply problems, thunderstorm activity, infestation by insects or vermin, tampering or repair by
unauthorised persons (including unauthorised alterations), exposure to abnormally corrosive conditions
or any foreign object or matter having entered the product.
4.This warranty does not cover the following items unless the fault or defect existed at the time of
purchase: Software
5.Warranty on Toughbook accessories (stylus, pens, AC charger, combo drive, etc) is 12 Months from the
date of purchase & 3 months for batteries.
6.To claim warranty service, when required, you should:
Check the Panasonic web site for latest warranty contact http://www.panasonic.com.au/toughbook, use
the Service Centre Locator and call the National Service Centre number indicated.
Prepare purchase receipt as proof of purchase date and system serial number which will be required by
the Authorised Service Centre.
7.The Warranty excludes 3 or less faulty pixels on screen.
8.The Warranty includes the repair or exchange of faulty parts within the product with items that are
functionally equivalent to that as originally supplied or better – including new or refurbished parts or
units – solely at Panasonic’s discretion.
9.It is the customer’s responsibility to backup all data from the hard disk drive before sending equipment
for repair. If a problem is related to the hard disk drive, or the hard disk drive has to be replaced,
Panasonic will only reload the factory pre-installed software for the product onto the replacement drive.
10.Panasonic will arrange free pick up and return for approved warranty repairs within 50 km of capital city
locations. Please ensure your unit is properly packed for return to the service location.
11.The warranties hereby conferred do not extend to, and exclude, any costs associated with the
installation, de-installation or re-installation of a product, including costs related to the mounting,
demounting or remounting of any screen, (and any other ancillary activities), delivery, handling,
freighting, transportation or insurance of the product or any part thereof or replacement of and do not
extend to, and exclude, any damage or loss occurring by reason of, during, associated with, or related
to such installation, de-installation, re-installation or transit.
Appendix
In addition to your rights under this warranty, Panasonic products come with consumer guarantees that
cannot be excluded under the Australian Consumer Law. If there is a major failure with the product, you can
reject the product and elect to have a refund or to have the product replaced or if you wish you may elect
to keep the goods and be compensated for the drop in value of the goods. You are also entitled to have the
product repaired or replaced if the product fails to be of acceptable quality and the failure does not amount
to a major failure.
If there is a major failure in regard to the product which cannot be remedied then you must notify us within
a reasonable period by contacting the Panasonic Customer Care Centre. If the failure in the product is not
a major failure then Panasonic may choose to repair or replace the product and will do so in a reasonable
period of time from receiving notice from you.
THIS PRODUCT IS NOT INTENDED FOR USE AS OR AS PART OF NUCLEAR EQUIPMENT/SYSTEMS,
52
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
52
2013/05/09
18:40:00
AIR TRAFFIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS*3.
PANASONIC WILL NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING FROM THE USE OF THIS
PRODUCT ARISING OUT OF THE FOREGOING USES.
*3
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class 2 Electronic Flight Bag (EFB) Systems and
Class 1 EFB Systems when used during critical phases of flight (e.g., during take-off and landing) and/or
mounted onto the aircraft. Class 1 EFB Systems and 2 EFB Systems are defined by FAA: AC (Advisory
Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36.
THIS WARRANTY CARD AND THE PURCHASE DOCKET (OR SIMILAR PROOF OF PURCHASE)
SHOULD BE RETAINED BY THE CUSTOMER AT ALL TIMES
If you require assistance regarding warranty conditions or any other enquiries, please visit the
Panasonic Australia website www.panasonic.com.au/toughbook or
contact by phone on 1300 132 463
Panasonic Australia Pty. Limited
ACN 001 592 187 ABN 83 001 592 187
1 Innovation Road, Macquarie Park NSW 2113
www.panasonic.com.au
11-11-2011
Appendix
PRO-031-F05 Issue: 4.0
53
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
53
2013/05/09
18:40:00
MEMO
54
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
54
2013/05/09
18:40:00
55
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
55
2013/05/09
18:40:00
Panasonic System Communications
Company of North America
Two Riverfront Plaza,
Newark NJ 07102
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga,
Ontario L4W 2T3
Panasonic Australia Pty. Limited
ACN 001 592 187 ABN 83 001 592 187
1 Innovation Road, Macquarie Park NSW 2113
Web Site : http://panasonic.net/
© Panasonic Corporation 2013
Printed in Taiwan
DFQW5716XAT_FZ-G1mk1_8_7_OI_M.indb
56
TA0113-2053
DFQW5716XAT
2013/05/09
18:40:00