Download Philips SHAVER 7000 SensoTouch 2D RQ1155

Register your product and get support at
www.philips.com/welcome
RQ1100 series
22_002_5349_2_DFU-Luxury_A6_v2.indd 1
2-7-2012 12:49:48
22_002_5349_2_DFU-Luxury_A6_v2.indd 2
2-7-2012 12:49:48
22_002_5349_2_DFU-Luxury_A6_v2.indd 3
1
2-7-2012 12:49:49
1
22_002_5349_2_DFU-Luxury_A6_v2.indd 4
2-7-2012 12:49:49
RQ119x, RQ118x, RQ117x, RQ116x, RQ115x, RQ114x, RQ113x
English 6
简体中文 35
22_002_5349_2_DFU-Luxury_A6_v2.indd 5
2-7-2012 12:49:49
6
English
Introduction
Congratulations on your purchase and welcome to
Philips! To fully benefit from the support that Philips
offers, register your product at www.philips.com/
welcome.
Please read this user manual, as it contains information
about the features of this shaver as well as some tips
to make shaving easier and more enjoyable.
General description  (Fig. 1)
AShaver
1Display
2 Shaver on/off button
3 Protection cap
4 RQ11 Shaving unit
B CRP331 Trimmer (RQ118x/RQ116x/RQ115x
only)
C RQ111 Beard Styler attachment (RQ1195/
RQ1185/RQ1175 only)
1 Hair length selector
2 Comb of Beard Styler attachment
D Jet Clean System (RQ1195CC/RQ1185CC/
RQ1180CC/RQ1175CC only)
1 Shaver holder
2 ’Cleaning chamber empty’ symbol
3 Cleaning symbol
4 Drying symbol
5 Jet Clean System on/off button
6 Cleaning chamber release button
EAdapter
FCharger
G Cleaning brush
H HQ200 Cleaning fluid (specific types only)
I Pouch (specific types only)
22_002_5349_2_DFU-Luxury_A6_v2.indd 6
2-7-2012 12:49:49
English
7
Important
Read this user manual carefully before you use the
shaver and the Jet Clean System and save it for
future reference.
Note: In this user manual the term ‘appliances’ refers
to the shaver and the Jet Clean System. If your shaver
does not come with a Jet Clean System, it refers to the
shaver only.
General
Danger
-- Make sure the adapter does not get wet.
Warning
-- The adapter contains a transformer. Do not cut
off the adapter to replace it with another plug, as
this causes a hazardous situation.
-- These appliances are not intended for use
by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been
given supervision or instruction concerning use of
these appliances by a person responsible for their
safety.
-- Children should be supervised to ensure that they
do not play with the shaver and the Jet Clean
System.
-- Be careful with hot water when you clean the
appliances. Always check if the water is not too
hot, to prevent your hands from getting burnt.
Caution
-- Never immerse the Jet Clean System and the
charger in water nor rinse them under the tap.
-- The appliances and accessories are not
dishwasher-proof.
22_002_5349_2_DFU-Luxury_A6_v2.indd 7
2-7-2012 12:49:50
8
English
-- Always place and use the appliances on a surface
that is fluid-resistant.
-- Use, charge and store the shaver at a temperature
between 5°C and 35°C.
-- Only use the accessories supplied with this shaver
or that have been specifically developed for this
shaver.
-- If the adapter or any of the other accessories is
damaged, always have it replaced with one of the
original type in order to avoid a hazard.
-- The adapter transforms 100-240 volts to a safe
low voltage of less than 24 volts.
-- Do not use the appliances and accessories if they
are damaged.
-- Water may leak from the socket at the bottom
of the shaver when you rinse it. This is normal
and not dangerous because all electronics are
enclosed in a sealed power unit inside the shaver.
Jet Clean system (specific types only)
Caution
-- Only use the Jet Clean System with the original
HQ200 cleaning fluid.
-- Always place and use the Jet Clean System on a
stable, level and horizontal fluid-resistant surface
to prevent leakage.
-- Never immerse the Jet Clean System in water.
-- Empty the cleaning chamber and clean it thoroughly
by rinsing it with hot tap water every 15 days.
-- The Jet Clean System thoroughly cleans but does
not disinfect your shaver, therefore do not share
the shaver with others.
-- The cleaning chamber of the Jet Clean System is
not dishwasher-proof.
-- When the Jet Clean System is ready for use, do
not move it to prevent leakage of cleaning fluid.
22_002_5349_2_DFU-Luxury_A6_v2.indd 8
2-7-2012 12:49:50
English
9
Beard Styler attachment (specific types
only)
Caution
-- Only use the Beard Styler attachment to trim
facial hair (beard, moustache and sideburns). Do
not use it to trim body parts below the neckline.
-- Only use the Beard Styler attachment in
combination with the following shaver types:
RQ12xx,RQ11xx, RQ10xx.
-- The Beard Styler attachment is not dishwasherproof.
Compliance with standards
-- This shaver complies with the internationally
approved safety regulations and can be safely used
in the bath or shower and cleaned under the tap.
-- These Philips appliances comply​comply with
all standards regarding electromagnetic fields
(EMF). If handled properly and according to the
instructions in this user manual, the appliances are
safe to use based on scientific evidence available
today.
The display
Note: If there is a protective foil on the display, remove
it before you use the shaver for the first time.
The various shaver types have different displays,
which are shown in the figures below.
22_002_5349_2_DFU-Luxury_A6_v2.indd 9
2-7-2012 12:49:50
10
English
-- RQ1195/RQ1180/RQ1175
-- RQ1185/RQ1160
-- RQ1155/RQ1151/RQ1150/RQ1145/RQ1141/
RQ1131
Charging
-- Charging takes approx. 1 hour.
RQ1195/RQ1180/RQ1175
-- When the shaver is charging, first the bottom
charging light flashes, then the second charging
light, and so on until the shaver is fully charged.
-- Quick charge: When the shaver contains enough
energy for one shave, the bottom charging light
alternately flashes orange and white.  
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
22_002_5349_2_DFU-Luxury_A6_v2.indd 10
2-7-2012 12:49:52
English 11
-- When the shaver is charging, first the plug symbol
and the battery symbol flash alternately. After
some time, the plug symbol goes out and the
battery symbol continues to flash until the shaver
is fully charged.
-- Quick charge: When the shaver contains enough
energy for one shave, the alternate flashing of the
plug symbol and battery symbol stops and only
the battery symbol flashes.
Battery fully charged
RQ1195/RQ1180/RQ1175
-- When the battery is fully charged, all charging
lights light up continuously. After approx. 30
minutes, the display automatically switches off
again.
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
-- When the battery is fully charged, the battery
symbol lights up continuously. After approx. 30
minutes, the display automatically switches off
again.
Battery low
RQ1195/RQ1180/RQ1175
-- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the
bottom charging light flashes orange.
-- When you switch off the shaver, the bottom
charging light continues to flash for a few seconds.
22_002_5349_2_DFU-Luxury_A6_v2.indd 11
2-7-2012 12:49:53
12
English
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
Note:The displays of the various shaver types look
different, but work in the same way.
-- When the battery is almost empty (when there
are only 5 or fewer shaving minutes left), the plug
symbol flashes.
-- When you switch off the shaver, the plug
symbol continues to flash for a few seconds.
Remaining battery capacity
RQ1195/RQ1180/RQ1175
-- The remaining battery capacity is indicated by the
number of charging lights that are on.
Travel lock
You can lock the shaver when you are going to
travel. The travel lock prevents the shaver from being
switched on by accident.
Activating the travel lock
1Press the on/off button for 3 seconds to enter
the travel lock mode.
,, The lock symbol lights up on the display.
Note:The displays of the various shaver types look
different, but show the same symbol.
Deactivating the travel lock
1Press the on/off button for 3 seconds.
,, The motor starts running to indicate that the
travel lock has been deactivated.
The shaver is now ready for use again.
22_002_5349_2_DFU-Luxury_A6_v2.indd 12
2-7-2012 12:49:55
English 13
Note:When you place the shaver in the pluggedin charger or Jet Clean System, the travel lock is
automatically deactivated.
Replace shaving head holder
Note:The displays of the various shaver types look
different, but show the same symbol.
For maximum shaving performance, we advise you
to replace the shaving head holder every two years.
-- To remind you to replace the shaving head holder,
the appliance is equipped with a replacement
reminder which is activated automatically after
approx. two years. The replacement reminder is
repeated at 9 successive shaves or until you reset
the shaver.
Charging
Charging takes approx. 1 hour.
RQ1195/RQ1185/RQ1180/RQ1175/RQ1160/
RQ1155: A fully charged shaver has a shaving time of
up to 50 minutes or 15 days.
RQ1151/RQ1150/RQ1145: A fully charged shaver
has a shaving time of up to 45 minutes or 13 days.
RQ1141/RQ1131: A fully charged shaver has a
shaving time of up to 40 minutes or 12 days.
Charge the shaver before you use it for the first
time and when the display indicates that the battery
is almost empty (see section ‘Battery low’ in chapter
‘The display’).
Quick charge
After the shaver has charged for 5 minutes,
it contains enough energy for one shave.
22_002_5349_2_DFU-Luxury_A6_v2.indd 13
2-7-2012 12:49:55
14
English
Charging in the charger
1Insert the small plug into the charger.
2Unfold the charger (‘click’).
3Put the adapter in the wall socket.
4Put the shaver in the charger (1) and press it
backwards until it locks into place (2).
,, The display shows that the shaver is charging
(see section ‘Charging’ in chapter ‘The display’).
Charging in the Jet Clean System (specific
types only)
1Put the small plug in the Jet Clean System.
2Put the adapter in the wall socket.
3Hold the shaver upside down above the holder
with the back of the shaver pointing towards
the holder.
Note: RQ1195/RQ1180/RQ1175: when you turn the
shaver upside down, the battery indication on the
display is also turned upside down so you can still see
to what level the battery is charged.
22_002_5349_2_DFU-Luxury_A6_v2.indd 14
2-7-2012 12:49:56
English 15
4Place the shaver body in the holder behind the
two clips (1) and press it down until it locks
into place (2).
Note:The shaver cannot be placed in the Jet Clean
System when the protection cap is on the shaving unit
or when the trimmer is placed on the shaver.
,, The display shows that the shaver is charging
(see chapter ‘The display’).
Using the shaver
Shaving
Skin adaptation period
Your first shaves may not bring you the result you
expect and your skin may even become slightly
irritated. This is normal. Your skin and beard need
time to adapt to any new shaving system.
We advise you to shave regularly (at least 3 times
a week) for a period of 3 weeks to allow your skin
to adapt to the new shaver. During this period, use
your new electric shaver exclusively and do not use
other shaving methods. If you use different shaving
methods, it is more difficult for your skin to adapt to
the new shaving system.
1Press the on/off button once to switch on the
shaver.
,, RQ1195/RQ1180/RQ1175: The display lights up
for a few seconds.
22_002_5349_2_DFU-Luxury_A6_v2.indd 15
2-7-2012 12:49:57
16
English
2Move the shaving heads over your skin in
circular movements.
-- Do not make straight movements.
3Press the on/off button once to switch off the
shaver.
,, RQ1195/RQ1180/RQ1175: The display lights up
for a few seconds and then shows the remaining
battery capacity.
Wet shaving
You can also use this shaver on a wet face with
shaving foam or shaving gel.
To shave with shaving foam or shaving gel, follow the
steps below:
1Apply some water to your skin.
2Apply shaving foam or shaving gel to your skin.
3Rinse the shaving unit under the tap to ensure
that the shaving unit glides smoothly over your
skin.
4Press the on/off button once to switch on the
shaver.
5Move the shaving heads over your skin in
circular movements.
Note: Rinse the shaver under the tap regularly to
ensure that it continues to glide smoothly over your
skin.
6Dry your face and thoroughly clean the
shaver after use (see chapter ‘Cleaning and
maintenance’).
Note: Make sure you rinse all foam or shaving gel off
the shaver.
22_002_5349_2_DFU-Luxury_A6_v2.indd 16
2-7-2012 12:49:58
English 17
Using the trimmer (specific types only)
You can use the trimmer to groom your sideburns
and moustache.
1Pull the shaving unit straight off the shaver.
Note: Do not twist the shaving unit while you pull it off
the shaver.
2Insert the lug of the trimmer into the slot in
the top of the shaver (1). Then press down the
trimmer (2) to attach it to the shaver (‘click’).
3Press the on/off button once to switch on the
trimmer.
,, RQ1180: The display lights up for a few seconds.
4You can now start trimming.
5Press the on/off button once to switch off the
trimmer.
,, RQ1180: The display lights up for a few seconds
to show the remaining battery capacity.
6Pull the trimmer straight off the shaver.
Note: Do not twist the trimming unit while you pull it
off the shaver.
7Insert the lug of the shaving unit into the slot
in the top of the shaver (1). Then press down
the shaving unit (2) to attach it to the shaver
(‘click’).
Using the Beard Styler attachment (specific
types only)
Note: Only use the Beard Styler attachment to trim
facial hair (beard, moustache and sideburns). Do not
use it to trim body parts below the neckline.
22_002_5349_2_DFU-Luxury_A6_v2.indd 17
2-7-2012 12:49:59
18
English
1Make sure the shaver is switched off.
2Pull the shaving unit straight off the shaver.
Note: Do not twist the shaving unit while you pull it off
the shaver.
3Insert the lug of the Beard Styler
attachment into the slot in the top of the
shaver (1). Then press down the Beard Styler
attachment (2) to attach it to the shaver
(‘click’).
Using the Beard Styler attachment with
comb
You can use the Beard Styler attachment with the
comb attached to style your beard at one fixed
setting, but also at different length settings. The
hair length settings on the Beard Styler attachment
correspond to the remaining hair length after cutting
and range from 1 to 5mm.
1Slide the comb straight into the guiding
grooves on both sides of the Beard Styler
attachment (‘click’).
2Press the length selector (1) and then push it
to the left or right (2) to select the desired
hair length setting.
3Press the on/off button on the shaver to switch
it on.
22_002_5349_2_DFU-Luxury_A6_v2.indd 18
2-7-2012 12:50:01
English 19
4You can now start styling your beard.
Using the Beard Styler attachment without
comb
You can use the Beard Styler attachment without the
comb to trim and contour your beard, moustache or
sideburns.
1Pull the comb off the Beard Styler attachment.
Note: Grab the comb in the centre to pull it off the
Beard Styler attachment. Do not pull at the sides of the
comb.
2Press the on/off button to switch on the shaver.
3You can now start to trim and contour your
beard, moustache, sideburns or neckline.
Beard styles
Below you find some examples of beard styles you
can create.
-- A stubble look
22_002_5349_2_DFU-Luxury_A6_v2.indd 19
2-7-2012 12:50:03
20
English
-- A full beard
-- A moustache
-- A goatee
Cleaning and maintenance
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as petrol or acetone to
clean the shaver, its accessories and the Jet Clean
System (specific types only).
-- The best and most hygienic way to clean the
shaver is in the Jet Clean System (specific types
only). You can also rinse the shaver under the tap
or clean it with the brush supplied.
-- Clean the shaver after every shave for optimal
shaving performance.
-- You can clean the outside of the shaver with a
damp cloth.
-- Regular cleaning guarantees better shaving
performance.
22_002_5349_2_DFU-Luxury_A6_v2.indd 20
2-7-2012 12:50:06
English 21
Cleaning the shaving unit
Be careful with hot water. Always check if the
water is not too hot, to prevent your hands from
getting burnt.
1Switch off the shaver. Remove it from the
charger or remove it from the Jet Clean
System (specific types only).
2Rinse the shaving unit under a hot tap for some
time.
Note:You can also clean the shaving unit with the
cleaning brush supplied. 
3Pull the shaving head holder off the bottom
part of the shaving unit and rinse it under a hot
tap for 30 seconds.
Note:You can also clean the shaving head holder with
the cleaning brush supplied. 
4Carefully shake off excess water and let the
shaving head holder dry.
Never dry the shaving unit with a towel or tissue,
as this may damage the shaving heads.
5Reattach the shaving head holder to the
bottom part of the shaving unit (‘click’).
Cleaning the shaving unit in the Jet Clean
System (specific types only)
The Jet Clean System has an automatic cleaning
program. When you press the on/off button, the
Jet Clean System starts cleaning in this automatic
cleaning program.
Preparing the Jet Clean System for use
Fill the cleaning chamber before first use.
22_002_5349_2_DFU-Luxury_A6_v2.indd 21
2-7-2012 12:50:07
22
English
1Put the small plug in the Jet Clean System.
2Put the adapter in the wall socket.
,, The holder automatically moves to the highest
position.
3Simultaneously press the release buttons on
both sides of the cleaning chamber (1). Then lift
the Jet Clean System off the cleaning chamber
(2).
,, The cleaning chamber remains behind.
4Unscrew the cap from the bottle with HQ200
cleaning fluid. 
5Fill the cleaning chamber with HQ200 cleaning
fluid to a level between the two lines.
6Place the Jet Clean System back onto the
cleaning chamber.
Make sure the release buttons click back into place.
Using the Jet Clean System
Note: If you use the shaver with shaving foam or
shaving gel, we advise you to rinse it under the hot tap
before you clean it in the Jet Clean System.This
guarantees an optimal lifetime for the cleaning fluid.
1Hold the shaver upside down above the holder
with the back of the shaver pointing towards
the holder.
2Place the shaver body in the holder behind the
two clips (1) and press it down until it locks
into place (2).
,, The display shows that the shaver is charging
(see chapter ‘The display’).
22_002_5349_2_DFU-Luxury_A6_v2.indd 22
2-7-2012 12:50:09
English 23
3Press the on/off button on the Jet Clean
System to start the cleaning program.
,, The shaver display stops showing the charging
indication.
,, The cleaning light starts to flash and the shaver is
automatically lowered into the cleaning fluid.
,, The cleaning light flashes throughout the
cleaning program, which takes a few minutes.
,, During the first phase of the cleaning program,
the shaver automatically switches on and off
several times and moves up and down.
,, During the second phase of the cleaning
program, the shaver is placed in the drying
position, indicated by the flashing drying symbol.
This phase takes approx. 2 hours. The shaver
stays in this position until the end of the
program.
,, After the cleaning program, the charging
indication appears on the shaver display (see
chapter ‘The display’).
Note: If you press the on/off button of the Jet
Clean System during the cleaning program, the
program aborts. In this case, the cleaning or drying
light stops flashing and the holder moves to the
highest position.
Note: If you remove the adapter from the wall socket
during the cleaning program, the program aborts.The
holder remains in its current position.When you put
the adapter back into the wall socket, the holder moves
to the highest position.
22_002_5349_2_DFU-Luxury_A6_v2.indd 23
2-7-2012 12:50:10
24
English
-- When the cleaning fluid drops below the
minimum level, the ‘cleaning chamber empty’
symbol starts to flash and the holder returns to its
starting position.
-- If you use the Jet Clean System to clean your
shaver every day, you need to refill the cleaning
chamber approx. every 15 days.
Cleaning the Jet Clean System
Clean the cleaning chamber every 15 days.
You can wipe the outside of the Jet Clean System
with a damp cloth.
1Simultaneously press the release buttons on
both sides of the Jet Clean System (1). Then lift
the Jet Clean System off the cleaning chamber
(2).
,, The cleaning chamber remains behind.
2Pour any remaining cleaning fluid out of the
cleaning chamber.
You can simply pour the cleaning fluid down the sink.
3Rinse the cleaning chamber under the tap.
The cleaning chamber is not dishwasher-proof.
4Fill the cleaning chamber with HQ200 cleaning
fluid to a level between the two lines.
22_002_5349_2_DFU-Luxury_A6_v2.indd 24
2-7-2012 12:50:11
English 25
5Place the Jet Clean System back onto the
cleaning chamber.
Make sure the release buttons click back into place.
Extra-thorough cleaning method
Make sure the appliance is switched off.
1Pull the shaving head holder off the bottom
part of the shaving unit.
2Slide the green retaining frame in the direction
of the arrows indicated on the retaining frame.
3Lift the retaining frame out of the shaving head
holder.
4Remove the cutter from the shaving guard.
Note: Do not clean more than one cutter and shaving
guard at a time, since they are all matching sets. If you
accidentally put a cutter in the wrong shaving guard,
it may take several weeks before optimal shaving
performance is restored.
22_002_5349_2_DFU-Luxury_A6_v2.indd 25
2-7-2012 12:50:12
26
English
5Clean the cutter with the cleaning brush
supplied.
6Clean the inside of the shaving guard.
7After cleaning, place the cutter back into the
shaving guard with the cutter legs pointing
downwards.
8Place the retaining frame back onto the shaving
head holder.
9Slide the guard back into place (‘click’).
22_002_5349_2_DFU-Luxury_A6_v2.indd 26
2-7-2012 12:50:14
English 27
10Reattach the shaving head holder to the
bottom part of the shaving unit.
Cleaning the trimmer
Clean the trimmer every time you have used it.
1Switch on the appliance with the trimmer
attached.
2Rinse the trimmer under a hot tap for some
time.
3After cleaning, switch off the appliance.
Tip: For optimal trimmer performance, lubricate the
trimmer teeth with a drop of sewing machine oil every
six months.
Cleaning the Beard Styler attachment
(specific types only)
Clean the Beard Styler attachment every time you
have used it.
1Pull the comb off the Beard Styler attachment.
2Rinse the Beard Styler attachment and the
comb separately under a hot tap for some
time.
Note:You can also clean the Beard Styler attachment
and the comb with the cleaning brush supplied.
3Lubricate the trimmer teeth with a drop of
sewing machine oil every six months.
22_002_5349_2_DFU-Luxury_A6_v2.indd 27
2-7-2012 12:50:15
28
English
Storage
1Slide the protection cap onto the shaving unit
to prevent damage to the shaving heads.
2Specific types only: Store the shaver in the
pouch supplied.
Replacement
For maximum shaving performance, we advise you
to replace the shaving head holder every two years.
Only replace the shaving head holder with an
original RQ11 Philips Shaving Head Holder.
Replacement reminder
To remind you to replace the shaving head holder,
the appliance is equipped with a replacement
reminder which is activated automatically after
approx. two years. The replacement reminder is
repeated at 9 successive shaves or until you reset
the shaver.
1The shaving unit symbol flashes when you
switch off the shaver.
Note:The displays of the various shaver types look
different, but show the same symbol.
2Pull the shaving head holder off the bottom
part of the shaving unit.
3Attach the new shaving head holder to the
bottom part of the shaving unit (‘click’).
22_002_5349_2_DFU-Luxury_A6_v2.indd 28
2-7-2012 12:50:16
English 29
4To reset the shaver, press and hold the on/off
button for approx. 10 seconds.
Note: If you do not reset the shaver at the first
replacement reminder, it continues to show the shaving
unit symbol at 8 more shaves or until you reset the
shaver.
Ordering accessories
To purchase accessories for this appliance, please
visit our online shop at www.shop.philips.com/
service. If the online shop is not available in
your country, go to your Philips dealer or a Philips
service centre. If you have any difficulties obtaining
accessories for your appliance, please contact the
Philips Consumer Care Centre in your country. You
find its contact details in the worldwide guarantee
leaflet.
The following parts are available
-- HQ8505 adapter
-- RQ11 Philips Shaving Head Holder
-- HQ110 Philips Shaving Head Cleaning Spray
-- HQ200 Philips Cleaning Fluid
-- RQ111 Beard Styler attachment
Shaving head holder
-- We advise you to replace the shaving head holder
every two years. Always replace the shaving head
holder with an original RQ11 Philips Shaving Head
Holder.
Cleaning
-- Specific types only: use Jet Clean Solution
(HQ200) for regular cleaning of the shaving heads.
22_002_5349_2_DFU-Luxury_A6_v2.indd 29
2-7-2012 12:50:17
30
English
Environment
-- Do not throw away the shaver and the Jet Clean
System (specific types only) with the normal
household waste at the end of their life, but
hand them in at an official collection point for
recycling. By doing this, you help to preserve the
environment.
-- The built-in rechargeable shaver battery contains
substances that may pollute the environment.
Always remove the battery before you discard or
hand in the shaver at an official collection point.
Dispose of the battery at an official collection
point for batteries. If you have trouble removing
the battery, you can also take the appliance to a
Philips service centre. The staff of this centre will
remove the battery for you and will dispose of it
in an environmentally safe way.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when
you discard the shaver. Make sure the battery is
completely empty when you remove it.
Be careful, the battery strips are sharp.
1Remove the back panel of the shaver with a
screwdriver.
2Remove the rechargeable battery.
22_002_5349_2_DFU-Luxury_A6_v2.indd 30
2-7-2012 12:50:18
English 31
Guarantee and service
If you need service or information or if you have a
problem, please visit the Philips website at
www.philips.com/support or contact the Philips
Consumer Care Centre in your country. You find its
phone number in the worldwide guarantee leaflet. If
there is no Consumer Care Centre in your country,
go to your local Philips dealer.
Guarantee restrictions
The shaving heads (cutters and shaving guards)
are not covered by the terms of the international
guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common
problems you could encounter with the appliance.
If you are unable to solve the problem with the
information below, visit www.philips.com/support for
a list of frequently asked questions or contact the
Consumer Care Centre in your country.
Problem
Possible cause
Solution
The shaver does
not shave as well
as it used to.
The shaving heads are
damaged or worn.
Replace the shaving
head holder (see
chapter ‘Replacement’).
Long hairs obstruct the
shaving heads.
Clean the shaving heads
by following the steps
of the extra-thorough
cleaning method (see
chapter ‘Cleaning and
maintenance’).
22_002_5349_2_DFU-Luxury_A6_v2.indd 31
2-7-2012 12:50:18
32
English
Problem
The shaver does
not work when I
press the on/off
button.
Possible cause
Solution
Specific types only: The
Jet Clean System has
not cleaned the shaver
properly, because the
cleaning fluid in the
cleaning chamber is
soiled or the cleaning
fluid level is too low.
Clean the shaver
thoroughly before you
continue shaving. If
necessary, clean and refill
the cleaning chamber
(see chapter ‘Cleaning
and maintenance’).
The rechargeable
battery is empty.
Recharge the battery
(see chapter ‘Charging’).
Specific types only: The
travel lock is activated.
Press the on/off button
for 3 seconds to
deactivate the travel
lock.
The shaving head holder
is soiled or damaged to
such an extent that the
motor cannot run.
Clean the shaving head
holder or replace it
(see chapters ‘Cleaning
and maintenance’ and
‘Replacement’). 
The temperature of the
shaver is too high. In this
case, the shaver does
not work.
Let the shaver cool
down. As soon as the
temperature of the
shaver has dropped
sufficiently, you can
switch on the shaver
again.
22_002_5349_2_DFU-Luxury_A6_v2.indd 32
2-7-2012 12:50:18
English 33
Problem
Possible cause
Solution
Specific types
only: The shaver
is not entirely
clean after I clean
it in the Jet Clean
System.
The cleaning fluid in
the cleaning chamber is
soiled.
Empty and rinse the
cleaning chamber and
refill it with new cleaning
fluid.
The cleaning fluid level
is too low. If the fluid
volume in the cleaning
chamber drops below
the minimum level
during the cleaning
program, the program
aborts.The cleaning
light and the ‘cleaning
chamber empty’ symbol
flash at intervals and
the holder returns to its
starting position.
Refill the cleaning
chamber with cleaning
fluid to a level between
the two lines (see
chapter ‘Cleaning and
maintenance’).
You have used another
cleaning fluid than the
original Philips cleaning
fluid.
Only use HQ200
Philips Cleaning Fluid.
The Jet Clean System
is not connected to the
mains.
Put the small plug in the
Jet Clean System and
put the adapter in the
wall socket.
Specific types
only: The Jet
Clean System
does not work
when I press the
on/off button.
22_002_5349_2_DFU-Luxury_A6_v2.indd 33
2-7-2012 12:50:18
34
English
Problem
The shaver is not
fully charged after
I charge it in the
charger/Jet Clean
System (specific
types only).
Possible cause
Solution
There is no electrical
connection between
the Jet Clean System
and the shaver.
Press the shaver tightly
into the holder to lock it
into place.
You have not placed the Make sure you press the
shaver in the charger/Jet shaver until it locks into
place.
Clean System (specific
types only) properly.
22_002_5349_2_DFU-Luxury_A6_v2.indd 34
2-7-2012 12:50:18
简体中文 35
简介
感谢您的惠顾，欢迎光临飞利浦！为了您能充
分享受飞利浦提供的支持，请在
www.philips.com/welcome 上注册您的产品。
请阅读本用户手册，手册包含有关此剃须刀各
种功能的信息以及一些使用技巧，让您的剃须
体验更轻松更舒适。
一般说明  (图 1)
A
1
2
3
4
B
C
1
2
D
1
2
3
4
5
6
E
F
G
H
I
22_002_5349_2_DFU-Luxury_A6_v2.indd 35
剃须刀
显示屏
剃须刀开/关按钮
保护盖
RQ11 剃须刀头部件
CRP331 修剪器（仅限于 RQ118x/RQ116x/
RQ115x）
RQ111 胡须造型器附件（仅限于 RQ1195/
RQ1185/RQ1175）
须发长度选择器
胡须造型器附件的修剪梳
Jet Clean 高效能清洁系统（仅限于
RQ1195CC/RQ1185CC/RQ1180CC/
RQ1175CC）
剃须刀支架
“清洗仓已空”符号
清洁符号
干燥符号
Jet Clean 高效能清洁系统开/关按钮
清洗仓释放按钮
适配器
充电器
清洁刷
HQ200 清洁剂（仅限于特定型号）
精美软袋（仅限于特定型号）
2-7-2012 12:50:19
36
简体中文
注意事项
使用剃须刀和 Jet Clean 高效能清洁系统之前，
请仔细阅读本用户手册，并妥善保管以供日后
参考。
注意： 在本用户手册中，术语“产品”指剃须
刀和 Jet Clean 高效能清洁系统。如果您的剃须
刀不随附 Jet Clean 高效能清洁系统，则它专
指剃须刀。
概述
危险
-- 确保电源适配器干燥。
警告
-- 警告符号注释：禁止用在打开的水龙头下进
行清洗。
-- 电源适配器内含有一个变压器。切勿将其剪
断，而用另一个插头代替，否则将导致严重
后果。
-- 电源软线不能更换，如果软线损坏，此器具
(电源适配器）应废弃。
-- 本产品不打算由肢体不健全、感觉或精神上
有障碍或缺乏相关经验和知识的人（包括儿
童）使用，除非有负责他们安全的人员对他
们使用这些产品进行监督或指导。
-- 应照看好儿童，确保他们不会玩耍剃须刀和
Jet Clean 高效能清洁系统。
-- 清洁产品时要小心使用热水。切记先检查水
温是否太高，以防手被烫伤。
-- 警告：将手持部分与电源软线分开后，才能
在水中清洗手持部分。
22_002_5349_2_DFU-Luxury_A6_v2.indd 36
2-7-2012 12:50:19
简体中文 37
注意
-- 切勿将 Jet Clean 高效能清洁系统和充电器浸
入水中，也不要放在水龙头下冲洗。
-- 产品和附件不可用洗碗机清洗。
-- 一定要在抗有机溶剂腐蚀的表面上放置和使
用本产品。
-- 必须在 5°C 至 35°C 之间的温度下使用、
存放和为剃须刀充电。
-- 仅使用本剃须刀随附的附件或专为本剃须刀
设计的附件。
-- 如果适配器或任何其他附件损坏，必须用原
装型号更换，以免发生危险。
-- 电源适配器可将 100-240 伏的电压转换为 24
伏以下的安全低电压。
-- 如果产品损坏，请勿使用本产品和附件。
-- 冲洗产品时，水可能从剃须刀底部的插口漏
出。这是正常的，而且没有危险，因为所有的
电子线路都密封在剃须刀内的一个密封壳内。
Jet Clean 高效能清洁系统（仅限于特定型号）
注意
-- Jet Clean 高效能清洁系统只能使用原装
HQ200 清洁剂。
-- Jet Clean 高效能清洁系统必须放在稳定、
平坦的抗有机溶剂腐蚀的水平表面上，以防
漏液。
-- 切勿将 Jet Clean 高效能清洁系统浸入水中。
-- 每 15 天倒空清洗仓一次，并用热水彻底冲洗。
-- Jet Clean 高效能清洁系统能彻底清洗您的剃
须刀，但不能消毒；因此切勿与他人共用剃
须刀。
-- Jet Clean 高效能清洁系统的清洗仓不可在洗
碗机中清洗。
-- 当Jet Clean 高效能清洁系统准备就绪时，
切勿移动本产品，以免清洁剂漏出。
22_002_5349_2_DFU-Luxury_A6_v2.indd 37
2-7-2012 12:50:19
38
简体中文
胡须造型器附件（仅限于特定型号）
注意
-- 仅使用胡须造型器附件修剪面部须发（胡
须、须髭和鬓角）。请勿将其用于修剪领口
以下的身体部位。
-- 仅将胡须造型器附件与以下型号的剃须刀结
合使用：RQ12xx、RQ11xx、RQ10xx。
-- 胡须造型器附件不能用洗碗机清洗。
符合标准
-- 此剃须刀符合国际认可的安全标准，可在洗
澡或淋浴时安全地使用，并可在水龙头下清
洗。
-- 符号注释：适合于在洗澡或淋浴时使用。
允许在盛水的浴缸、淋浴、洗脸盆或其他器
皿附近使用本器具。
-- 这些飞利浦产品符合关于电磁场 (EMF) 的所
有相关标准。据目前的科学证明，如果正确
使用并按照本用户手册中的说明进行操作，
本产品是安全的。
显示屏
注意： 如果显示屏上有保护膜，首次使用剃须
刀时，请将其取下。
不同型号的剃须刀具有不同的显示屏，具体如
下图所示。
-- RQ1195/RQ1180/RQ1175
-- RQ1185/RQ1160
22_002_5349_2_DFU-Luxury_A6_v2.indd 38
2-7-2012 12:50:19
简体中文 39
-- RQ1155/RQ1151/RQ1150/RQ1145/RQ1141/
RQ1131
充电
-- 充电约需 1小时。
RQ1195/RQ1180/RQ1175
-- 剃须刀充电时，底部的第一个充电指示灯会
先闪烁，接着第二个充电指示灯闪烁，以此
类推，直到剃须刀完全充满电。
-- 快速充电：当剃须刀包含的电量仍够剃须一
次时，底部的充电指示灯会交替闪烁橙色和
白色。
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
注意： 不同型号的剃须刀显示屏外观不同。但
工作原理是一样的。
-- 剃须刀充电时，插头符号和电池符号先交替
闪烁。一段时间后，插头符号熄灭，电池符
号持续闪烁直至剃须刀完全充满电。
-- 快速充电：当剃须刀包含的电量仍够剃须一
次时，插头符号和电池符号将停止交替闪
烁，仅电池符号闪烁。
22_002_5349_2_DFU-Luxury_A6_v2.indd 39
2-7-2012 12:50:21
40
简体中文
电池已完全充满
RQ1195/RQ1180/RQ1175
-- 当电池完全充满电时，所有充电指示灯均会
持续亮起。大约 30 分钟后，显示屏会再次自
动关闭。
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
注意： 不同型号的剃须刀显示屏外观不同。但
工作原理是一样的。
-- 当电池完全充满电时，电池符号会持续亮
起。大约 30 分钟后，显示屏会再次自动关
闭。
电池电量不足
RQ1195/RQ1180/RQ1175
-- 当电池电量快要耗尽时（仅剩 5 分钟或更少
的剃须时间），底部的充电指示灯将闪烁橙
色。
-- 关闭剃须刀时，底部的充电指示灯将持续闪
烁几秒钟。
RQ1185/RQ1160/RQ115x/RQ114x/RQ113x
注意： 不同型号的剃须刀显示屏外观不同。但
工作原理是一样的。
-- 当电池电量快要耗尽时（仅剩 5 分钟或更少
的剃须时间），插头符号将会闪烁。
-- 关闭剃须刀时，插头符号将持续闪烁几秒
钟。
电池剩余电量
RQ1195/RQ1180/RQ1175
-- 剩余的电池电量由亮起的充电指示灯数来表
示。
22_002_5349_2_DFU-Luxury_A6_v2.indd 40
2-7-2012 12:50:22
简体中文 41
旅行锁
您可以在携带剃须刀旅行之前将其锁住。旅行
锁可防止剃须刀被意外打开。
启用旅行锁
1按住开/关按钮 3 秒钟以进入旅行锁模式。
,, 锁符号将在显示屏上亮起。
注意： 不同型号的剃须刀显示屏外观不同。
但显示相同的符号。
解除旅行锁
1按开/关按钮 3 秒钟。
,, 马达开始运行即表示旅行锁已解除。
现在可以重新开始使用剃须刀。
注意： 当您将剃须刀插接到充电器或放到 Jet
Clean 高效能清洁系统中时，旅行锁将自动解除。
更换剃须刀头支架
注意： 不同型号的剃须刀显示屏外观不同。
但显示相同的符号。
为获得最佳剃须效果，建议每两年更换一次剃
须刀头支架。
-- 为了提醒您更换剃须刀头部件，产品配备了
更换提醒，该提醒在约两年后自动激活。更
换提醒会在连续剃须 9 次后或直至您重置剃
须刀前重复。
22_002_5349_2_DFU-Luxury_A6_v2.indd 41
2-7-2012 12:50:23
42
简体中文
充电
充电约需 1小时。
RQ1195/RQ1185/RQ1180/RQ1175/RQ1160/
RQ1155：完全充电的剃须刀剃须时间可长达
50 分钟或 15 天。
RQ1151/RQ1150/RQ1145：完全充电的剃须刀
剃须时间可长达 45 分钟或 13 天。
RQ1141/RQ1131：完全充电的剃须刀剃须时间
可长达 40 分钟或 12 天。
第一次使用剃须刀之前，或当显示屏指示电池电
量快要耗尽时，请先为剃须刀充电（参见“显示
屏”一章中的“电池电量不足”部分的内容）。
快速充电
剃须刀在充电 5 分钟后，其含有的电量便足以
完成一次剃须。
在充电器中充电
1将小插头插入充电器。
2展开充电器（可听到“咔哒”一声）。
3将电源适配器插入电源插座。
4将剃须刀插接到充电器中 (1) 然后将其向后
按，直到其锁定到位 (2)。
,, 显示屏将显示剃须刀正在充电（参见“显示
屏”一章中的“充电”部分的内容）。
22_002_5349_2_DFU-Luxury_A6_v2.indd 42
2-7-2012 12:50:24
简体中文 43
在 Jet Clean 高效能清洁系统中充电（仅限于
特定型号）
1将小插头插入 Jet Clean 高效能清洁系统。
2将电源适配器插入电源插座。
3将剃须刀倒置按在支架上，使剃须刀的背面
朝向支架。
注意： RQ1195/RQ1180/RQ1175：将剃须刀
倒置时，显示屏上的电池指示也会倒置，因此
您仍然能够看清电池充电的情况。
4将剃须刀机身放在两个固定夹后的支架中
(1) 并将其按下，直到其锁定到位 (2)。
注意： 当剃须刀头部件上套了保护盖，或剃
须刀上装了修发器时，不可将剃须刀放到 Jet
Clean 高效能清洁系统中。
,, 显示屏将显示剃须刀正在充电（见“显示
屏”一章）。
使用剃须刀
剃毛
皮肤适应期
前几次剃须可能不会带给您预期效果，并且您
的皮肤可能会受到轻度刺激。这是正常的。
您的皮肤和胡须需要时间适应新的剃须系统。
建议您在 3 周时间内定期剃须（至少每周 3
次），以便让您的皮肤适应新的剃须刀。在此
期间，请仅使用新的电动剃须刀，不要使用其
他剃须方法。如果您使用不同的剃须方法，那
么您的皮肤会更难适应新的剃须系统。
22_002_5349_2_DFU-Luxury_A6_v2.indd 43
2-7-2012 12:50:24
44
简体中文
1按一下开/关按钮以启动剃须刀。
,, RQ1195/RQ1180/RQ1175：显示屏将亮起几
秒钟的时间。
2将剃须刀头在您的皮肤上作迂回运动。
-- 请勿作直线运动。
3按一下开/关按钮关闭剃须刀电源。
,, RQ1195/RQ1180/RQ1175：显示屏将亮起几
秒钟时间，然后显示电池剩余电量。
湿剃
您也可以先用剃须泡沫或剃须啫喱将脸弄湿，
然后再用此剃须刀进行剃须。
要用剃须泡沫或剃须啫喱剃须，请按照下面的
步骤执行操作：
1用水润湿一下皮肤。
2在皮肤上涂上剃须泡沫或剃须啫喱。
3在水龙头上冲洗一下剃须刀头部件，确保剃
须刀头部件可以在您的皮肤上顺畅滑动。
4按一下开/关按钮以启动剃须刀。
5将剃须刀头在您的皮肤上作迂回运动。
注意： 在水龙头下定期冲洗剃须刀，确保其能
够继续在您的皮肤上顺畅滑动。
6使用后，擦干您的脸并彻底清洁剃须刀
（见“清洁和保养”一章）。
注意： 确保冲洗干净剃须刀上的泡沫或剃须啫
喱。
22_002_5349_2_DFU-Luxury_A6_v2.indd 44
2-7-2012 12:50:24
简体中文 45
使用修剪器（仅限于特定型号）
您可使用修剪器修剪鬓角和小胡子。
1将剃须刀头部件竖直抽离剃须刀。
注意： 将其抽离剃须刀时，不要旋转剃须刀头
部件。
2将修剪器的凸缘插入剃须刀顶部的槽内 (1)
。然后按下修剪器 (2) 以将其安装在剃须刀
上（可听到“咔哒”一声）。
3按一下开/关按钮打开修发器。
,, RQ1180：显示屏将亮起几秒钟的时间。
4现在可以开始修剪了。
5按一下开/关按钮关闭修发器。
,, RQ1180：显示屏将亮起几秒钟时间，以显示
电池剩余电量。
6将修发器竖直抽离剃须刀。
注意： 将其抽离剃须刀时，不要旋转修剪部
件。
7将剃须刀头部件的凸缘插入剃须刀顶部的槽
内 (1)。然后按下剃须刀头部件 (2) 以将其
安装在剃须刀上（可听到“咔哒”一声）。
22_002_5349_2_DFU-Luxury_A6_v2.indd 45
2-7-2012 12:50:25
46
简体中文
使用胡须造型器附件（仅限于特定型号）
注意： 仅使用胡须造型器附件修剪面部须发
（胡须、须髭和鬓角）。请勿将其用于修剪领
口以下的身体部位。
1确保剃须刀已关闭。
2将剃须刀头部件竖直抽离剃须刀。
注意： 将其抽离剃须刀时，不要旋转剃须刀头
部件。
3将胡须造型器附件的凸缘插入剃须刀顶部的
槽内 (1)。然后按下胡须造型器附件 (2) 以
将其安装在剃须刀上（可听到“咔哒”一
声）。
使用带修剪梳的胡须造型器附件
您可以使用带修剪梳的胡须造型器附件以固定
设置（也可使用不同的长度设置）修整胡须。
胡须造型器附件的须发长度设置对应修剪后剩
余的须发长度，范围为 1 到 5 毫米。
1将修剪梳直接滑入胡须造型器附件两侧的导
槽中（可听到“咔哒”一声）。
2按下长度选择器 (1)，然后将其向左或向右
推动 (2) 以选择所需的须发长度设置。
3按下剃须刀上的开/关按钮将其打开。
22_002_5349_2_DFU-Luxury_A6_v2.indd 46
2-7-2012 12:50:25
简体中文 47
4您现在可以开始修整胡须。
使用不带修剪梳的胡须造型器附件
您可以使用不带修剪梳的胡须造型器附件修剪
和修整胡须、须髭或鬓角的轮廓。
1将修剪梳抽离胡须造型器附件。
注意： 抓住修剪梳的中心位置，将其抽离胡须
造型器附件。请勿拉拔修剪梳的侧面。
2按下开/关按钮启动剃须刀。
3您现在可以开始修剪和修整胡须、须髭、鬓
角或颈部的轮廓。
胡须造型
您可以在下面找到您可塑造的胡须造型的一些
示例。
-- 胡茬造型
-- 大胡子
22_002_5349_2_DFU-Luxury_A6_v2.indd 47
2-7-2012 12:50:27
48
简体中文
-- 须髭
-- 山羊胡
清洁和保养
切勿使用钢丝绒、研磨性清洁剂或腐蚀性液体
（例如汽油或丙酮）来清洁剃须刀、剃须刀附
件和 Jet Clean 高效能清洁系统（仅限于特定
型号）。
-- 在 Jet Clean 高效能清洁系统（仅限于特定
型号）中清洁剃须刀是最有效、最卫生的方
法。您还可以在水龙头下冲洗剃须刀或用随
附的毛刷进行清洁。
-- 每次剃须后清洁剃须刀，以获得最佳的剃须
性能。
-- 可以用湿布清洁剃须刀的外侧。
-- 为保证更好的剃须效果，剃须刀必须定期清
洗。
22_002_5349_2_DFU-Luxury_A6_v2.indd 48
2-7-2012 12:50:28
简体中文 49
清洁剃毛刀头部件
使用热水时一定要小心。切记先检查水温是否
太高，以防烫手。
1关闭剃须刀。将其从充电器中拔出，或从
Jet Clean 高效能清洁系统中拔出（仅限于
特定型号）。
2在热水龙头下冲洗一会儿剃须刀头部件。
注意： 您也可以使用随附的清洁刷清洁剃须刀
头部件。 
3将剃须刀头支架抽离剃须刀头部件的底部，
然后在热水龙头下冲洗 30 秒。
注意： 您也可以使用随附的清洁刷清洁剃须刀
头支架。 
4小心甩干多余的水，然后使剃须刀头支架干
燥。
不要用毛巾或纸巾擦拭剃须刀头部件，因为这
样可能会损坏剃须刀头。
5将剃须刀头支架重新装回剃须刀头部件的底
部（可听到“咔哒”一声）。
在 Jet Clean 高效能清洁系统中清洁剃须刀头部
件（仅限于特定型号）
Jet Clean 高效能清洁系统具有一个自动清洗程
序。按下开/关按钮时，Jet Clean 高效能清洁系
统将开始以此自动清洗程序清洁。
Jet Clean 高效能清洁系统使用准备
首次使用之前请将清洁剂注满清洗仓。
1将小插头插入 Jet Clean 高效能清洁系统。
2将电源适配器插入电源插座。
,, 支架将自动移到最高位置。
22_002_5349_2_DFU-Luxury_A6_v2.indd 49
2-7-2012 12:50:28
50
简体中文
3同时按下清洗仓两侧的释放钮 (1)。然后将
Jet Clean 高效能清洁系统从清洗仓上提起
(2)。
,, 留下清洗仓。
4拧开装 HQ200 清洁剂的瓶子的瓶盖。 
5给清洗仓注入 HQ200 清洁剂，水量在两线
之间为宜。
6将 Jet Clean 高效能清洁系统重新放在清洗
仓上。
确保释放键卡回到位。
使用 Jet Clean 高效能清洁系统
注意： 如果您在剃须时使用了剃须泡沫或剃须啫
喱，建议您在将剃须刀放入 Jet Clean 高效能清
洁系统清洁之前，先在热水龙头下冲洗干净。
这样可以保证清洁剂拥有最佳的使用寿命。
1将剃须刀倒置按在支架上，使剃须刀的背面
朝向支架。
2将剃须刀机身放在两个固定夹后的支架中
(1) 并将其按下，直到其锁定到位 (2)。
,, 显示屏将显示剃须刀正在充电（见“显示
屏”一章）。
22_002_5349_2_DFU-Luxury_A6_v2.indd 50
2-7-2012 12:50:29
简体中文 51
3按 Jet Clean 高效能清洁系统上的开/关按钮
以启动清洁程序。
,, 剃须刀显示屏停止显示充电指示。
,, 清洗指示灯开始闪烁，剃须刀将自动降到清
洁剂中。
,, 清洗指示灯在整个清洗程序中不断闪烁，这
需要几分钟时间。
,, 在清洗程序的第一个阶段，剃须刀将开关数
次，并会向上和向下移动。
,, 在清洗程序的第二个阶段，剃须刀处在干燥
档位，这由一个闪烁的干燥符号表示。此阶
段大约需要 2 小时。在此程序结束之前剃须
刀一直都会处在此档位。
,, 清洗程序结束后，充电指示将出现在剃须刀
显示屏上（见“显示屏”一章）。
注意： 如果在清洗程序运行期间按 Jet Clean
高效能清洁系统的开/关按钮，则程序将中断。
此时，清洗或干燥指示灯将停止闪烁，支架将
回到最高位置。
注意： 如果在清洗程序运行期间将适配器从插
座上拔除，则程序将中断。支架将保持在当前
位置不变。当您将适配器重新插入插座时，支
架将继续移动到最高的位置。
-- 当清洁剂水位下降至最低水位以下时，“清
洗仓已空”符号将开始闪烁，支架将返回到
起始位置。
-- 如果每天都使用 Jet Clean 高效能清洁系统清
洗您的剃须刀，则需要大约每 15 天向清洗仓
内补充清洁剂一次。
22_002_5349_2_DFU-Luxury_A6_v2.indd 51
2-7-2012 12:50:29
52
简体中文
清洁 Jet Clean 高效能清洁系统
每隔 15 天清洁一次清洗仓。
您可以用湿布擦拭 Jet Clean 高效能清洁系统
的外表面。
1同时按下 Jet Clean 高效能清洁系统两侧的
释放钮 (1)。然后将 Jet Clean 高效能清洁
系统从清洗仓上提起 (2)。
,, 留下清洗仓。
2将清洗仓中残余的清洁剂倒出。
您只需将清洁剂倒入水槽。
3在水龙头下冲洗清洗仓。
清洗仓不可在洗碗机中清洗。
4给清洗仓注入 HQ200 清洁剂，注入量在两
线之间为宜。
5将 Jet Clean 高效能清洁系统重新放在清洗
仓上。
确保释放键卡回到位。
22_002_5349_2_DFU-Luxury_A6_v2.indd 52
2-7-2012 12:50:30
简体中文 53
超彻底清洁方法
确保产品电源已关闭。
1将剃须刀头支架从剃须刀头部件的底部抽
离。
2按固定架所示的箭头方向滑动绿色固定架。
3将固定架从剃须刀头支架中提起并取出。
4将刀片从网罩上取下。
注意： 不要同时清洁多组刀片和网罩，因为它
们都是相互匹配的。如果不小心将刀片装到了
错误的网罩上，则需要数周时间才能恢复产品
的最佳剃须性能。
5用随附的清洁刷清洁刀片。
22_002_5349_2_DFU-Luxury_A6_v2.indd 53
2-7-2012 12:50:30
54
简体中文
6清洁网罩的内侧。
7清洁后，将刀片重新装回至网罩，刀片底部
朝下。
8装固定架装回到剃须刀头支架上。
9将网罩滑回到位（可听到“咔哒”一声）。
10 将剃须刀头支架重新装回剃须刀头部件的底
部。
22_002_5349_2_DFU-Luxury_A6_v2.indd 54
2-7-2012 12:50:31
简体中文 55
清洁修发器
每次使用后都要清洁修剪器。
1打开装有修剪器的产品。
2在热水龙头下冲洗一会儿修发器。
3清洁完成后，关闭产品。
提示： 为获得最佳修剪性能，每六个月用一滴
缝纫机油润滑修发器齿。
清洁胡须造型器附件（仅限于特定型号）
每次使用后，请清洁胡须造型器附件。
1将修剪梳抽离胡须造型器附件。
2在热水龙头下单独冲洗胡须造型器附件和修
剪梳片刻。
注意： 您也可以用随附的清洁刷清洁胡须造型
器附件和修剪梳。
3每六个月用一滴缝纫机油润滑修发器齿。
存储
1将保护盖滑动到剃须刀头部件上，以防损坏
剃须刀头。
2仅限于特定型号：用随附的精美软袋存放剃
须刀。
22_002_5349_2_DFU-Luxury_A6_v2.indd 55
2-7-2012 12:50:31
56
简体中文
更换
为获得最佳剃须效果，建议每两年更换一次剃
须刀头支架。
仅使用原装 RQ11 飞利浦剃须刀头支架更换剃
须刀头支架。
更换提醒
为了提醒您更换剃须刀头部件，产品配备了更换
提醒，该提醒在约两年后自动激活。更换提醒会
在连续剃须 9 次后或直至您重置剃须刀前重复。
1关闭剃须刀后，剃须刀头部件符号闪烁。
注意： 不同型号的剃须刀显示屏外观不同。但
显示相同的符号。
2将剃须刀头支架从剃须刀头部件的底部抽
离。
3将新的剃须刀头支架装回剃须刀头部件的底
部（可听到“咔哒”一声）。
4要重置剃须刀，按住开/关按钮约 10 秒钟。
注意： 如果在首次更换提醒后您未重置剃须
刀，连续剃须 8 次后或直至您重置剃须刀前，
它将持续显示剃须刀头部件符号。
22_002_5349_2_DFU-Luxury_A6_v2.indd 56
2-7-2012 12:50:31
简体中文 57
订购附件
要购买本产品的附件，请访问我们的在线商城
www.shop.philips.com/service。如果您的国
家/地区没有在线商城，请联系您的飞利浦经销
商或飞利浦服务中心。如果您在购买产品的附
件时遇到困难，请联系您所在国家/地区的飞利
浦客户服务中心。可在全球保修卡中找到其详
细联系信息。
可选配以下附件
-- HQ8505 适配器
-- RQ11 飞利浦剃须刀头支架
-- HQ110 飞利浦剃须刀头清洁喷雾剂
-- HQ200 飞利浦高效能清洁剂
-- RQ111 胡须造型器附件
剃须刀头支架
-- 建议您每两年更换一次剃须刀头支架。务必
使用原装 RQ11 飞利浦剃须刀头支架进行更
换。
清洁
-- 仅限于特定型号：使用喷雾清洁溶液
(HQ200) 定期清洁剃须刀头。
环保
-- 弃置剃须刀和 Jet Clean 高效能清洁系统（仅
限于特定型号）时，请不要将其与一般生活
垃圾堆放在一起；应将其交给官方指定的回
收中心。这样做有利于环保。
22_002_5349_2_DFU-Luxury_A6_v2.indd 57
2-7-2012 12:50:32
58
简体中文
-- 内置充电电池含有可能会污染环境的物质。
丢弃剃须刀时，一定要将电池取出，或将剃
须刀送到官方指定的回收站。到官方指定的
电池回收站处理电池。如果您在取出电池时
遇到问题，您也可以将剃须刀送至飞利浦维
修中心。维修中心的员工会帮您取出电池，
并以环保的方式处理它。
卸下剃须刀的充电电池
只有在丢弃剃须刀时才可取下充电电池。请确
保在取下电池时电量已完全耗尽。
注意，电池带非常锋利。
1使用螺丝刀卸下剃须刀的背部面板。
2卸下充电电池。
保修与服务
如果您需要服务或信息，或者有任何疑问，请
访问飞利浦网站：www.philips.com/support。
您也可与您所在国家/地区的飞利浦客户服务
中心联系（可从全球保修卡中找到其电话号
码）。如果您所在的国家/地区没有飞利浦客户
服务中心，请与当地的飞利浦经销商联系。
保修条款
由于剃须刀头（刀片和网罩）属于易磨损物
品，因此不在国际保修条款的涵盖范围之列。
故障种类和处理方法
本章归纳了使用本产品时最常见的一些问题。
如果您无法根据以下信息解决问题，请访问
www.philips.com/support 查阅常见问题列表，
或联系您所在国家/地区的客户服务中心。
22_002_5349_2_DFU-Luxury_A6_v2.indd 58
2-7-2012 12:50:32
简体中文 59
问题
可能的原因
解决方法
剃须刀的剃
须效果没有
以前好。
剃须刀头已损坏或磨
损。
更换剃须刀头支架（
见“更换”一章）。
过长的胡须堵塞了剃须
刀头。
通过执行下列彻底清洁
方法中的步骤来清洁剃
须刀头（见“清洁和保
养”一章）。
仅限于特定型号：由于
清洗仓内的清洁剂可能
受到污染或清洁剂水位
太低，Jet Clean 高效
能清洁系统可能无法正
常清洗剃须刀。
在继续剃须之前，请先
彻底清洁剃须刀。如有
必要，请清洁清洗仓并
为其重新注入清洁剂（
见“清洁和保养”一
章）。
按下开/关钮 充电电池的电量已耗
时，剃须刀 尽。
不工作。
给电池充电（见“充
电”一章）。
仅限于特定型号：旅行
锁已被激活。
按住开/关按钮 3 秒钟以
禁用旅行锁。
剃须刀头支架被污染或
损坏，导致马达无法
运行。
清洁剃须刀头支架或进
行更换（见“清洁和
保养”及“更换”章
节）。 
剃须刀的温度过高。此
时，剃须刀无法工作。
让剃须刀冷却。一旦剃
须刀降到足够低的温
度，便可重新打开剃须
刀。
22_002_5349_2_DFU-Luxury_A6_v2.indd 59
2-7-2012 12:50:32
60
简体中文
问题
可能的原因
解决方法
仅限于特定
型号：剃须
刀放在 Jet
Clean 高效
能清洁系统
中清洁之后
依然没有完
全干净。
清洗仓内的清洁剂可能
被污染。
将清洗仓倒空并用水冲
洗，然后再加入新清洁
剂。
清洁剂水位过低。如果
在清洗程序运行期间
清洗仓中的液体容量降
到了最低水位以下，程
序将中断。清洗指示灯
和“清洗仓已空”符号
将开始间歇性闪烁，
支架将恢复至最初的
位置。
给清洗仓重新注入清洁
剂，水位在两线之间
为宜（见“清洁和保
养”一章）。
您使用了其他清洁剂，
而不是原装飞利浦清
洁剂。
仅可使用 HQ200 飞利浦
清洁剂。
Jet Clean 高效能清洁
系统未通电。
将小插头插入 Jet Clean
高效能清洁系统，然后
将电源适配器插入电源
插座。
仅限于特定
型号：按
下开/关按
钮时，Jet
Clean 高效
能清洁系统
不工作。
22_002_5349_2_DFU-Luxury_A6_v2.indd 60
2-7-2012 12:50:32
简体中文 61
问题
剃须刀在
充电器/Jet
Clean 高效
能清洁系统
（仅限于特
定型号）中
无法充满
电。
可能的原因
解决方法
Jet Clean 高效能清洁
系统和剃须刀之间未
通电。
将剃须刀牢固地按入支
架，使其锁定到位。
剃须刀在充电器/Jet
Clean 高效能清洁系统
（仅限于特定型号）中
插接不正确。
确保您按下剃须刀，
直到其锁定到位。
22_002_5349_2_DFU-Luxury_A6_v2.indd 61
2-7-2012 12:50:32
62
简体中文
22_002_5349_2_DFU-Luxury_A6_v2.indd 62
2-7-2012 12:50:34
22_002_5349_2_DFU-Luxury_A6_v2.indd 63
简体中文 63
2-7-2012 12:50:36
22_002_5349_2_DFU-Luxury_A6_v2.indd 64
2-7-2012 12:50:37
22_002_5349_2_DFU-Luxury_A6_v2.indd 65
2-7-2012 12:50:37
22_002_5349_2_DFU-Luxury_A6_v2.indd 66
Regi
ww
RQ
4222.002.5349.2
2-7-2012 12:50:37