Transcript
LC200C Ceiling Mount for Monitors up to 32" with up to 200mm VESA Patterns LC200C Ceiling Flange Follow the directions provided by the monitor manufacturer to expose the VESA mounting pattern of threaded inserts on the back of the monitor. Attach the VESA Plate to the monitor with Monitor Attaching Screws specified by the monitor manufacturer. Several screw sizes are provided for conveinience. Lag Screws Predetermine the best possible viewing location for the monitor allowing for tilt and pivot action. Use the LC200C Ceiling Flange as a template to mark and drill pilot holes 2-1/3" deep into the wood ceiling joist using a 1/8" bit for each of the lag screw locations. 1" NPT Outside Pipe LC200C Flange Cover Cord Access Hole Countersunk Screws Attach the LC200C Ceiling Flange to the ceiling wood joist using the provided Lag Screws. If mounting into concrete, metal beams or at an angle, contact Lucasey for ceiling mount accessories compatible with this mount. Attach the LC200C Flange Cover to the LC200C Ceiling Flange using the provided countersunk screws. 1/4-28 x 5/16" Setscrews Do Not Remove the Safety Cable Do Not Adjust Past the Red Line Inside Adjustable Pipe Carefully slide the Inside Adjustable Pipe, with attached monitor, into the Outside Pipe. Adjust to the appropriate length (Do not adjust past the red line) and tighten the Setscrews. If desired, run the monitor cords through the pipes using the Cord Access Hole at the top and the hole in the bottom of the Inside Adjustable Pipe. Screw the Outside Pipe, with attached monitor, into the LC200C Ceiling Flange. Double check to make sure all fasteners, including the adjustable pipe setscrews, are secure and tight. Hardware List Monitor Not Included VESA Plate Flat Washers Monitor Attaching Screws LC200C_Ins (12/07) #14 x 2-1/2" HWH Lag Screws ........................................................... 4 5/16-18 x 1-7/8" Flanged SHC Bolt ...................................................... 1 5/16-18 Nylock Nuts ............................................................................ 1 5/16" Bellville Washers ...................................................................... 2 1/4-20 x 1-1/2" Flanged SHC Bolt ........................................................ 1 1/4-20 Nylock Nuts .............................................................................. 1 1/4" Bellville Washers ......................................................................... 4 1/4-28 x 5/16" Setscrews .................................................................... 2 #10-32 x 3/4" Countersunk Screws .................................................... 2 4mm x 25mm Set Screws ... 5mm x 30mm Set Screws ... 6mm x 30mm Set Screws ... 4mm x 12mm Phillips Screws ... 5mm x 12mm Phillips Screws ... 6mm x 12mm Phillips Screws ... ©2005 Lucasey Manufacturing Corporation, Oakland, California 6 6 6 6 6 6 4mm Hex Nuts 5mm Hex Nuts 6mm Hex Nuts 5mm Flat Washers 1/4" Flat Washers ... 12 ... 12 ... 12 ... 36 ... 18 www.lucasey.com Protected under one or more of these U.S. Patent numbers: 3,291,432 3,559,942 3,724,798 DES.270,689 4,613,109 4,878,645 4,852,842 DES.309,5624,973,023 5,169,114 5,255,884 5,310,152 5,522,576 5,621,614 Re.35,677 DES.398,834 5,826,384 5,941,492 5,964,068 6,060,661 6,102,398 6,158,704 6,454,116B1 6,761,276B2 6,806,425B1 INSTALLATION INSTRUCTIONS