Download Lian Li PC-Z70B computer case

Installation Guide
Case components
Rubberized
grommets for
liquid cooling
tubing
140mm fans x 2
Multi-media ports
Power switch
120mm fan
Reset switch
5.25" mounting bezels
Patented
tool-less 5.25”
device mounting
Patented tool-less
PCI add-on card
holder
Removable
120mm fans
with air filter
Hot swap
3.5" HDD cage
(For 3.5" HDD x 9)
VGA card
support column
Patented tool-less
PSU mounting
bracket
Removable
2.5" HDD module
(For 2.5" HDD x 2)
Hardware list
USB
Buzzer (1)
Longer thumb screw (3)
for motherboard mount
Thumb screw(36)
for HDD
PCI card holder/B (4)
USB 3.0 to USB 2.0
converter
Rubber slide rail (18)
for HDD
PCI card holder/A (8)
Bracket (1)
for power supply mounting
Shorter thumb screw (9)
for motherboard mount
Screw driver (1)
to ass’y motherboard
Cable ties (2)
Thumb screw (8)
for PCI card holder
Screw (4)
for PSU mounting
Stand off bolt (3)
for motherboard (spare parts)
Nut (3)
for stand off
Box (1)
for spare parts
Screw (20)
for 2.5" HDD/spare parts
Mounting bracket
for SSI CEB/EEB M/B
Key is in the
accessories box
!
Note: For hard to reach areas
use long thumb screws.
!
1
!
for SSI CEB/EEB
The oval hole on the M/B
tray is designed for special
server boards. Please use
a nut to secure the copper
bolt in place
2
Remove six
thumb screws.
Slide the panel backward
to release.
Remove front panel
ODD installation
Pull the front panel towards
yourself.
Press the right and left sides
of the bezel to remove.
3.5” HDD module installation
Place the M/B on the copper bolt and secure
with thumb screws.
Remove four thumb screws, to release
the VGA card support column
Press the plastic handle to
release the mounting bracket.
Push the ODD into the 5.25"
rack.
Close the bracket to secure
the ODD.
2.5” HDD module installation
2
L
Install the screws to the HDD
with anti-vibration rubber rings.
Slide the HDD into the
HDD cage.
Fasten eight screws.
Slide the HDD into the
HDD cage.
1
1.Close the gate to secure
the HDD.
2.Lock.
C50.Z7000.01E-1
PSU installation
Place the PSU bracket into the slot
as shown.
Place the PSU on the stand, and
push against the rear panel.
Lock the PSU bracket to
secure the PSU.
* For transportation, please use
screws to secure the PSU.
VGA card pillar installation guide
Cable management
L
Insert PCI card holder/A
Use PCI card holder/B for thick VGA cards.
PCI add-on card installation
Remove air filter
Washable air filter on the right-side
Washable air filter below the PSU
1
2
Open the aluminum latch to remove
the PCI slot bracket.
Push the card into the PCI slot, close
the aluminum latch to secure the card.
Slide the air filter to remove.
Rotate washable air filter clockwise to
remove.
Change fan from right-side to left-side
Slide the fan up to remove.
Remove six screws to
release the bracket.
I/O port installation
Supports motherboard
USB 3.0 20 Pin header
Place the bracket on the
other side, fasten six screws
to secure.
Place the fan into the bracket
and slide down to secure.
Cable installation guide
HD AUDIO
E-SATA USB 2.0 USB 3.0 USB 3.0 MIC EAR
USB 3.0
Supports liquid cooling
systems
BLUE 10
BLACK PURPLE 8
YELLOW 6
BROWN 4
RED 2
USB 2.0
9
7
5
3
1
GREEN
KEY
ORANGE
N.C.
GND+H.S. TUBE
GROUND
PWR
WHITE
GRAY
GROUND
Reset
PLED-
WHITE
BLUE
WHITE
NC
GREEN
PLED+
IDE_LEDIDE_LED+
E-SATA
Speaker
SATA
Cable
+5V
POWER SW
RESET SW
POWER
LED
WHITE
ORANGE
H.D.D LED
BLACK
NC
NC
RED
SPEAKER
USB 3.0 to USB 2.0 converter
20
10
USB
11
1
VCC
RED
D- WHITE
D+ GREEN
GND BLACK
RED
WHITE
GREEN
BLACK
KEY
VCC
DD+
GND
C50.Z7000.01E-2