Download Lindy 25036 switch component

Modules for
24 + 2Giga N-WAY SNMP Ethernet Switch
Short Guide
LINDY No. 25032
LINDY No. 25033
LINDY No. 25034
LINDY No. 25035
LINDY No. 25036
English
2 Port RJ-45 Gigabit 10/100/1000Base-T
1 Port Fibre Optic Gigabit Type SC 1000Base-SX
2 Port Fibre Optic Gigabit Type SC 1000Base-SX
1 Port Fibre Optic Fast Ethernet Type SC 100Base-FX
2 Port Fibre Optic Fast Ethernet Type SC 100Base-FX
Please find the complete detailed user manual in PDF format on
the CD-ROM enclosed with the 24+2Giga SNMP N-Way Switch.
Unpacking
The product should contain the following items:
o One module according to the LINDY part number, check from Part No. above.
o This Short Guide
Installation
Before you install the module in the 24+2Giga SNMP Switch, turn off the power to the switch.
Unscrew the face plate of the module slot, this is on the front of the 24+2Giga SNMP Switch.
Then install the module by fixing the two module screws. Switch on the power to 24+2Giga
SNMP switch again.
After the Switch is powered on, it will perform “self-diagnostic” (POSD). This process takes
about 1 min and 40 seconds to complete, during this process, the “DIAG” LED will blink green
and the Switch will not respond to any configuration program. All the connections to the Switch
will not be available at this time. When the process is completed, the “DIAG” LED will stay solid
green.
The following table describes the meaning of each LED indicator.
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (JUNE 2003)
LED
Power
DIAG
Cooling Fan 1
Fan 2
Link/Act
(1 ~24 port)
100 Mbps
(1 ~24 port)
Colour Status
Solid
Blinking
Green
Green
Red
Red
Green
Power is applied to this device
Self Diagnostic successful
Left cooling fan failure
Right cooling fan failure
10Mbit/sec link established
N/A
Performing self diagnostic test
N/A
N/A
TX/RX activity or collision
Green
OFF
100Mbit/sec link established
10Mbit/sec established
N/A
N/A
10/100/1000 Mbp/s RJ-45 Gigabit Port Optional Module
Bottom LED
Top LED
Middle LED
Top & Middle
LEDs
Green
N/A
Orange 100Mbit/sec link established
when Middle LED OFF
Green
10Mbit/sec link established
when Top LED OFF
Orange 1000Mbit/sec link established
& Green when both LED’s ON
TX/RX activity or collision
N/A
N/A
N/A
FCC Compliance Statement (United States)
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used properly, that is, in strict accordance with the manufacturer’s instructions, may cause
interference to radio communication.
It has been tested and found to comply with the limits for a class A computing device in
accordance with the specifications in Subpart B of part 15 of FCC rules, which are designed to
provide reasonable protection against such interference when the equipment is operated in a
commercial environment. Operation of this equipment in a residential area may cause
interference, in which case the user at his own expense will be required to take whatever
measures may be necessary to correct the interference.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Canadian Department of Communications RFI statement
This equipment does not exceed the class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de la classe A prescrites dans le règlement sur le
brouillage radioélectriques publié par le ministère des Communications du Canada
Tested to comply
with FCC Standards
LINDY No. 25030 , 25032, 25033, 25034, 25035, 25036