Download JVC KS-FX270 Cassette Player User Manual

ENGLISH
RECEPTOR-REPRODUCTOR DE CASSETTE KS-FX270
ESPAÑOL
KS-FX270
RADIOCASSETTE
FRANÇAIS
CASSETTE RECEIVER
KS-FX270
LOUD
DISP
VCR
Multi
Music
Scan
SCAN
7
8
9
10
11
12
MO
32
For installation and connections, refer to the separate manual.
Para la instalación y las conexiones, refiérase al manual separado.
Pour l’installation et les raccordements, se référer au manuel séparé.
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MANUEL D’INSTRUCTIONS
For customer Use:
Enter below the Model No. and
Serial No. which are located on
the top or bottom of the cabinet.
Retain this information for future
reference.
Model No.
Serial No.
GET0008-001A
[J]
EN00.COVER.KS-FX270[J]/f
3
10/27/00, 3:51 PM
ENGLISH
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
BASIC OPERATIONS .................................................... 3
RADIO OPERATIONS ................................................... 4
Listening to the radio ..................................................................... 4
Storing stations in memory ............................................................ 5
FM station automatic preset: SSM .............................................. 5
Manual preset .............................................................................. 6
Tuning into a preset station ........................................................... 7
Other convenient tuner functions ................................................. 8
Scanning broadcast stations ....................................................... 8
Selecting FM reception sound ..................................................... 8
TAPE OPERATIONS ..................................................... 9
Listening to a tape .......................................................................... 9
Finding the beginning of a tune ................................................... 10
Other convenient tape functions ................................................. 11
Prohibiting tape ejection ............................................................ 11
Skipping the blank portions on the tape .................................... 11
Repeat Function ........................................................................ 11
SOUND ADJUSTMENTS ............................................. 12
Turning on/off the loudness function .......................................... 12
Selecting preset sound modes ...................................................... 12
Adjusting the sound ...................................................................... 13
Using the Sound Control Memory .............................................. 14
Selecting and Storing the sound modes .................................... 14
Recalling the sound modes ....................................................... 15
Canceling Advanced SCM ........................................................... 16
Storing your own sound adjustments ......................................... 17
OTHER MAIN FUNCTIONS ......................................... 18
Setting the clock ............................................................................ 18
Selecting the level display ............................................................ 19
Detaching the control panel ......................................................... 20
CD CHANGER OPERATIONS ...................................... 21
Playing CDs ................................................................................... 21
Selecting CD playback modes ..................................................... 23
REMOTE OPERATIONS .............................................. 24
Installing the battery .................................................................... 24
Using the remote controller ......................................................... 25
EXTERNAL COMPONENT OPERATIONS ...................... 26
Selecting the external component to use ..................................... 27
MAINTENANCE ........................................................ 28
To extend the lifetime of the unit ................................................. 28
How to Reset your unit ................................................................. 28
TROUBLESHOOTING ................................................. 29
SPECIFICATIONS ....................................................... 30
BEFORE USE
★ For safety....
• Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
• Stop the car before performing any complicated
operations.
★
Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
2
EN02-03.KS-FX270[J]/f
2
10/27/00, 3:52 PM
ENGLISH
BASIC OPERATIONS
1
3
2
1
Note:
When you use this unit for the
first time, set the built-in
clock correctly, see page 18.
Turn on the power.
Note on One-Touch Operation:
When you select a source in step 2 below, the power automatically comes on.
You do not have to press this button to turn on the power.
2
Select the source.
To operate the tuner, see pages 4 – 8.
To operate the tape deck, see pages 9 – 11.
To operate the CD changer, see pages 21 – 23.
To operate the external component, see pages 26 – 27.
3
Adjust the volume.
Volume level indicator
4
Volume level appears
Adjust the sound as you want (see pages 12 – 17).
To drop the volume in a moment
Press
briefly while listening to any source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the button briefly again.
To turn off the power
Press
for more than 1 second.
3
EN02-03.KS-FX270[J]/f
3
10/27/00, 3:52 PM
ENGLISH
RADIO OPERATIONS
Listening to the radio
1
1
2
Select the band (FM1, FM2, FM3 or AM).
You can select any one of FM1, FM2, and FM3 to listen to an
FM station.
Selected band appears
FM1
FM2
FM3
AM
Audio or volume level indicator
2
To search stations of
higher frequencies.
Start searching a station.
When a station is received, searching stops.
To search stations of
lower frequencies.
To stop searching before a station is received, press the same button you have pressed
for searching.
To tune in a particular frequency manually:
1 Press FM/AM to select the band.
2 Press and hold ¢
or 4
until “M” starts flashing on the display.
Now you can manually change the frequency while “M” is flashing.
3 Press ¢
or 4
repeatedly until the frequency you want is reached.
• If you hold down the button, the frequency keeps changing until you release the button.
4
EN04-08.KS-FX270[J]/f
4
10/27/00, 3:52 PM
ENGLISH
Storing stations in memory
You can use one of the following two methods to store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-station Sequential Memory)
• Manual preset of both FM and AM stations
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band (FM1, FM2, and FM3).
1
1
FM1
FM2
FM3
2
AM
Select the FM band number (FM1, FM2 or
FM3) you want to store FM stations into.
2
Press and hold the both buttons for more than
2 seconds.
“SSM” appears, then disappears when automatic
preset is over.
Local FM stations with the strongest signals are searched and stored automatically in the
band number you have selected (FM1, FM2 or FM3). These stations are preset in the number
buttons — No. 1 (lowest frequency) to No. 6 (highest frequency).
When automatic preset is over, the station stored in number button 1 will be automatically
tuned in.
5
EN04-08.KS-FX270[J]/f
5
10/27/00, 3:52 PM
ENGLISH
Manual preset
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.
EXAMPLE: Storing an FM station of 88.3 MHz into the preset number 1 of the FM1 band
3
1
1
2
Select the FM1 band.
2
Tune into a station of 88.3 MHz.
See page 4 to tune into a station.
3
Press and hold the button for more than 2
seconds.
Preset number “P1” starts flashing for a while.
4
Repeat the above procedure to store other station into other
preset numbers.
Notes:
• A previously preset station is erased when a new station is stored in the same preset number.
• Preset stations are erased when the power supply to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset the stations again.
6
EN04-08.KS-FX270[J]/f
6
10/27/00, 3:52 PM
ENGLISH
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If you have not stored them yet, see pages 5
and 6.
2
1
1
Select the band (FM1, FM2, FM3 or AM) you
want.
FM1
FM2
FM3
AM
2
Select the number (1 – 6) for the preset station
you want.
7
EN04-08.KS-FX270[J]/f
7
10/27/00, 3:52 PM
ENGLISH
Other convenient tuner functions
SCAN
MO/RND
Scanning broadcast stations
When you press SCAN while listening to the radio, station scanning starts. Each time a
broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes
on the display), and you can check what program is now being broadcasted.
If you want to listen to that program, press the same button again to stop scanning.
Selecting FM reception sound
When an FM stereo broadcast is hard to receive:
Press MO/RND (mono/random) while listening to an FM stereo broadcast. The sound you
hear becomes monaural but reception will be improved.
Lights up when receiving an
FM broadcast in stereo.
To restore the stereo effect, press the same button again.
8
EN04-08.KS-FX270[J]/f
8
10/27/00, 3:52 PM
TAPE OPERATIONS
1
1
ENGLISH
Listening to a tape
2
Insert a cassette.
The unit turns on and tape play starts automatically.
When one side of the tape reaches its end during play, the
other side of the tape automatically starts playing. (Auto
Reverse)
Note on One-Touch Operation:
When a cassette is already in the cassette compartment, pressing TAPE 2 3 turns on the
unit and starts tape play automatically.
2
Select the tape direction.
Each time you press the button, the tape direction changes
) and reverse (
).
alternatively – forward (
To stop play and eject the cassette
Press 0.
Tape play stops and the cassette automatically ejects from the cassette compartment.
If you change the source to AM/FM or CD-CH, the tape play also stops (without ejecting the
cassette this time).
• You can also eject the tape with the unit turned off.
9
EN09-11.KS-FX270[J]/f
9
10/27/00, 3:53 PM
ENGLISH
To fast-forward and rewind a tape
• Press ¢
for more than 1 second to fast-forward the
tape.
When the tape reaches its end, the tape is reversed and
playback starts from the beginning of the other side.
for more than 1 second to rewind the tape.
• Press 4
When the tape reaches its end, playback of the same side
starts.
Tape direction
To stop fast-forward and rewind at any position on the tape, press TAPE 2 3.
Tape play starts from that position on the tape.
Finding the beginning of a tune
Multi Music Scan allows you to automatically start playback from the beginning of a specified
tune. You can specify up to 9 tunes ahead or before the current tune.
¢
4
During playback
To locate a tune ahead of the
current tune on the tape
Specify how many tunes ahead or
before the current tune the tune you
want is located.
To locate a tune before the
current tune on the tape
Each time you set the tune, the number changes
up to ±9.
When the beginning of the specified tune is located, playback starts automatically.
Notes:
• While locating a specified tune:
– If the tape is rewound to its beginning, playback starts from the beginning of that side.
– If the tape is fast forwarded to the end, it is reversed and played from the beginning of the other
side.
• In the following cases, the Multi Music Scan function may not operate correctly.
– Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions
during tunes.
– Tapes with short non-recorded sections.
10 – Tapes with high level noise or humming between tunes.
EN09-11.KS-FX270[J]/f
10
10/27/00, 3:53 PM
ENGLISH
Other convenient tape functions
TAPE
23
0
Prohibiting tape ejection
RPT
You can prohibit the tape ejection and can “lock” a tape in the cassette compartment.
Press and hold TAPE 2 3 and 0 for more than 2 seconds. “NO EJECT” flashes on the
display for about 5 seconds, and the tape is “locked.”
To cancel the prohibition and “unlock” the tape, press and hold TAPE 2 3 and 0 for
more than 2 seconds again. “EJECT OK” flashes again for about 5 seconds, and this time the
tape is “unlock.”
Skipping the blank portions on the tape
You can skip blank portions between the tunes. (Blank Skip)
When this function is on, the unit skips blank portions of 15 seconds or more, fast-forwards to
the next tune, then starts playing it.
1. Press and hold SEL (select) for more than 2 seconds.
or 4
.
2. Select “B. SKIP (blank skip)” with ¢
3. Select the desired mode with the control dial.
The Blank Skip mode alternates between on and off.
ON Ô OFF
Note:
When the tape reaches its end while fast-forwarding, the tape direction will be changed automatically.
Repeat Function
Press the RPT button while a tune you would like to hear over again is being played back.
When the tape reaches the end of the tune, the tape is automatically rewound to the beginning
of that tune and playback resumes from there. This operation will be repeated till the RPT
button is pressed again.
Notes:
In the following cases, the Multi Music Scan, and Repeat function mechanisms may not operate correctly.
These are NOT malfunctions; use the mechanisms to suitably accommodate the materials and situations.
• Tapes with tunes having long pianissimo passages (very quiet parts) or non-recorded portions during
tunes.
• Tapes with tunes recorded at low recording levels.
• Tapes with short non-recorded sections.
11
• Tapes with high level noise or humming between tunes.
EN09-11.KS-FX270[J]/f
11
10/27/00, 3:53 PM
ENGLISH
SOUND ADJUSTMENTS
Turning on/off the loudness function
The human ear is less sensitive to low and high frequencies at low volumes.
The loudness function can boost these frequencies to produce a well-balanced sound at low
volume level.
Each time you press LOUD, the loudness function turns on/off alternatively.
Selecting preset sound modes
You can select a preset sound adjustment suitable to the music genre.
Each time you press SCM, the sound mode changes as follows.
Indication
For:
Preset values
Bass
Treble
Loudness
00
On
SCM OFF
(Flat sound)
00
BEAT
Rock or disco music
+02
00
On
SOFT
Quiet background music
+01
–03
Off
POP
Light music
+04
+01
Off
Notes:
• You can adjust the preset sound mode as you like, and store in memory.
If you want to adjust and store your original sound mode, see “Storing your own sound adjustments”
on page 17.
• To adjust only the bass and treble reinforcement levels as you like, see “Adjusting the sound” on
page 13.
12
EN12-17.KS-FX270[J]/f
12
10/27/00, 3:54 PM
ENGLISH
Adjusting the sound
You can adjust the treble/bass sounds and the speaker balance.
2
1
1
Select the item you want to adjust.
Indication
To do:
Range
BAS
(bass)
Adjust the bass
–06 (min.)
—
+06 (max.)
TRE
(treble)
Adjust the treble
–06 (min.)
—
+06 (max.)
FAD
(Fader)*
Adjust the front and rear speaker
balance
R06 (rear only) —F06 (front only)
BAL
(Balance)
Adjust the left and right speaker
balance
L06 (left only) — R06 (right only)
VOL
(Volume)
Adjust the volume
00 (min.)
—
50 (max.)
Note:
* If you are using a two-speaker system, set the fader level to “00”.
2
Adjust the level.
Note:
Normally the control dial work as the volume control buttons. So
you do not have to select “VOL” to adjust the volume level.
13
EN12-17.KS-FX270[J]/f
13
10/27/00, 3:54 PM
ENGLISH
Using the Sound Control Memory
You can select and store a preset sound adjustment suitable to each playback source.
(Advanced SCM)
Selecting and storing the sound modes
Once you select a sound mode, it is stored in memory, and will be recalled every time you
select the same source. A sound mode can be stored for each of the following sources —
FM1, FM2, FM3, AM, Tape, CD-Changer and external components.
•
If you do not want to store the sound mode separately for each playback source, but want
to use the same sound mode for all the sources, see “Canceling Advanced SCM” on page
16.
“SCM” indicator
1
1
Select the sound mode you want.
Each time you press the button, the sound mode changes
as follows:
• When “SCM LINK” is set to “LINK ON”, the selected sound
mode can be stored in memory for the current source and
the effect applies only to the current source. Each time
you change the playback source, the SCM indicator flashes
on the display.
• When “SCM LINK” is set to “LINK OFF”, the selected sound
mode effect applies to any source.
Indication
For:
Preset values
Bass
Treble
Loudness
00
On
SCM OFF
(Flat sound)
00
BEAT
Rock or disco music
+02
00
On
SOFT
Quiet background music
+01
–03
Off
POP
Light music
+04
+01
Off
14
EN12-17.KS-FX270[J]/f
14
10/27/00, 3:54 PM
ENGLISH
Recalling the sound modes
1
1
Select the source while the “SCM” indicator
is lit on the display.
The “SCM” indicator starts flashing, and the sound mode
stored in memory for the selected source is recalled.
Sound mode indicators
Notes:
• You can adjust each sound mode to your preference, and store it in memory.
If you want to adjust and store your original sound mode, see “Storing your own sound adjustments”
on page 17.
• To adjust the bass and treble reinforcement levels or to turn on/off the loundness function temporarily,
see page 12 and 13. (Your adjustments will be canceled if another source is selected.)
15
EN12-17.KS-FX270[J]/f
15
10/27/00, 3:54 PM
ENGLISH
Canceling Advanced SCM
You can cancel the Advanced SCM (Sound Control Memory), and unlink the sound modes
and the playback sources.
When shipped from the factory, a different sound mode can be stored in memory for each
source so that you can change the sound modes simply by changing the sources.
LINK ON: Advanced SCM (different SCMs for different sources)
LINK OFF: Conventional SCM (one SCM for all sources)
3
1,4
1
2
Press and hold SEL for more than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “B.SKIP”
or “EXT IN★” appears on the display.
★
2
Displayed only when one of the following sources is selected—
FM, AM and TAPE.
Select “SCM LINK” if not shown on the display.
3
Select the desired mode — “LINK ON” or
“LINK OFF”.
4
Finish the setting.
16
EN12-17.KS-FX270[J]/f
16
10/27/00, 3:54 PM
You can adjust the sound modes (BEAT, POP, SOFT: see page 12) as you like and store your
own adjustments in memory.
ENGLISH
Storing your own sound adjustments
3
2
2
1
1,4
Call up the sound mode you want to adjust.
See page 12 for details.
Within
5 seconds
2
To adjust the bass or treble sound level
Select “BAS” or “TRE.”
To turn on or off the loudness function
Each time you press LOUD, the loudness function turns on
and off alternatively. (= go to step 4)
Within
5 seconds
3
Adjust the bass or treble level.
See page 13 for details.
Within
5 seconds
4
Press and hold SCM until the sound mode
you have selected in step 1 flashes on the
display.
Your setting is stored in memory.
5
Repeat the same procedure to store other settings.
To reset to the factory settings
Repeat the same procedure and reassign the preset values listed in the table on page 12.
EN12-17.KS-FX270[J]/f
17
10/27/00, 3:54 PM
17
ENGLISH
OTHER MAIN FUNCTIONS
Setting the clock
2,3
1,4
1
DISP
Press and hold the button for more than 2
seconds.
“CLOCK H,” “CLOCK M”, “SCM LINK”, “LEVEL”, “B.SKIP”
or “EXT IN★” appears on the display.
★
Displayed only when one of the following sources is selected —
FM, AM and TAPE.
2
1.
Set the hour.
1. Select “CLOCK H” if not shown on the display
2.
2. Adjust the hour.
3
1.
Set the minute.
1. Select “CLOCK M.”
2.
2. Adjust the minute.
4
Finish the setting.
To check the current clock time (changing the display mode)
Press DISP repeatedly. Each time you press the button, the display mode changes as follows.
During tuner
operation:
During CD Changer operation: During external
Tiempo
de
Número
Elapsed
Disc
Clock
Hora Component operation:
reproducción
During tape
operation:
playing time
transcurrido
Frequency
18
Clock Play mode
Clock
de
disco
number
LINE IN
Clock
• If the unit is not in use when you press DISP, the power turns on, the clock time is shown for
5 seconds, then the power turns off.
EN18-20.KS-FX270[J]/f
18
10/27/00, 3:54 PM
ENGLISH
Selecting the level display
You can select the level display according to your preference.
When shipped from the factory, “AUDIO 2” is selected.
AUDIO1: Shows the audio level indicator.
AUDIO2: Alternates “AUDIO 1” setting and illumination display.
OFF : Erases the audio level indicator.
3
2
1,4
1
Press and hold SEL for more than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “B.SKIP”
or “EXT IN★” appears on the display.
★
Displayed only when one of the following sources is selected —
FM, AM and TAPE.
2
Select “LEVEL” if not shown on the display.
3
Select the desired mode — “AUDIO 1”,
“AUDIO 2” or “OFF”.
4
Finish the setting.
19
EN18-20.KS-FX270[J]/f
19
10/27/00, 3:54 PM
ENGLISH
Detaching the control panel
You can detach the control panel when leaving the car.
When detaching or attaching the control panel, be careful not to damage the connectors on
the back of the control panel and on the panel holder.
How to detach the control
panel
Before detaching the control panel, be sure
to turn off the power.
1
2
3
How to attach the control
panel
1
Unlock the control panel.
Lift and pull the control panel
out of the unit.
Put the detached control
panel into the provided case.
2
Insert the left side of the
control panel into the groove
on the panel holder.
Press the right side of the
control panel to fix it to the
panel holder.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
Connectors
20
EN18-20.KS-FX270[J]/f
20
10/27/00, 3:54 PM
Read this section only when you used with a JVC CD automatic changer (separately
purchased).
We recommend that you use one of the CH-X series with your unit.
If you have another CD automatic changer, consult your JVC car audio dealer for connections.
• For example, if your CD automatic changer is one of the KD-MK series, you need a cord (KSU15K) for connecting it to this unit.
ENGLISH
CD CHANGER OPERATIONS
Before operating your CD automatic changer:
• Refer also to the Instructions supplied with your CD changer.
• If no discs are in the magazine of the CD changer or the discs are inserted upside
down, “NO CD” or “NO DISC” will appear on the display. If this happens, remove the
magazine and set the discs correctly.
• If “RESET 1 - RESET 8” appears on the display, something is wrong with the connection
between this unit and the CD changer. If this happens, check the connection, connect
the connecting cord(s) firmly if necessary, then press the reset button of the CD changer.
Playing CDs
Number buttons
1
1
¢
4
Select the CD automatic changer.
Play back starts from the first track of the first disc.
All tracks of all discs are played back.
Disc number
Track number
Elapsed playing time
(The clock time is shown if you have pressed
DISP to see the clock time. See page 18.)
Note on One-Touch Operation:
When you press CD-CH, the power automatically comes on. You do not have to press
to turn on the power.
21
EN21-23.KS-FX270[J]/f
21
10/27/00, 3:54 PM
ENGLISH
To fast forward or reverse the track
Press and hold ¢
, while playing a CD, to fast forward the track.
Press and hold 4
, while playing a CD, to reverse the track.
To go to the next track or the previous track
Press ¢
briefly, while playing a CD, to go ahead to the beginning
of the next track. Each time you press the button consecutively, the
beginning of the next tracks is located and played back.
Press 4
briefly, while playing a CD, to go back to the beginning
of the current track. Each time you press the button consecutively,
the beginning of the current tracks is located and played back.
To go to a particular disc directly
Press the number button corresponding to the disc number to start its
playback.
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1 second.
Ex. When disc number 3 is selected
Disc number
Track number
22
EN21-23.KS-FX270[J]/f
22
10/27/00, 3:55 PM
ENGLISH
Selecting CD playback modes
RPT MO RND
To play back tracks at random (Random Play)
MO
Mode
Each time you press MO/RND (mono/random) while playing a CD, CD
random play mode changes as follows:
RND1
RND2
(Random1)
(Random2)
RND Indicator
Canceled
Plays at random
RND1
Lights
All tracks of the current disc, then the tracks of the
next disc, and so on.
RND2
Flashes
All tracks of all discs inserted in the magazine.
To play back tracks repeatedly (Repeat Play)
Each time you press RPT (Repeat) while playing a CD, CD repeat play
mode changes as follows:
Mode
RPT1
RPT2
(Repeat1)
(Repeat2)
RPT Indicator
Canceled
Plays repeatedly
RPT1
Lights
The current track (or specified track).
RPT2
Flashes
All tracks of the current disc (or specified disc).
23
EN21-23.KS-FX270[J]/f
23
10/27/00, 3:55 PM
ENGLISH
REMOTE OPERATIONS
Remote sensor
Before using the remote controller:
• Aim the remote controller directly at the remote sensor
on the main unit. Make sure there is no obstacle in
between.
• Do not expose the remote sensor to strong light (direct
sunlight or artificial lighting).
Installing the battery
When the controllable range or effectiveness of the remote controller decreases, replace
the battery.
(back side)
1)
2)
Lithium coin battery
(product number:
CR2025)
1. Remove the battery holder.
1) Push out in the direction indicated by the arrow
using a ball point pen or a similar tool.
2) Remove the battery holder.
2. Place the battery.
Slide the battery into the holder with the + side facing
upwards so that the battery is fixed in the holder.
3. Return the battery holder.
Insert again the battery holder pushing it until you hear
a clicking sound.
(back side)
WARNING:
• Store the batteries in a place which children cannot reach.
If a child accidentally swallows the battery, immediately consult a doctor.
• Do not recharge, short, disassemble or heat the batteries or dispose of in a fire.
Doing any of these things may cause the batteries to give off heat, crack or start a fire.
• Do not leave the batteries with other metallic materials.
Doing this may cause the batteries to give off heat, crack or start a fire.
• When throwing away or saving the batteries, wrap in tape and insulate; otherwise, , it may cause
the batteries to give off heat, crack or start a fire.
• Do not poke the batteries with tweezers or similar tools.
Doing this may cause the batteries to give off heat, crack or start a fire.
24
EN24-30.KS-FX270[J]/f
24
00.11.10, 10:51 AM
5
6
1
2
7
3
4
RM-RK31
1 Functions the same as the
button on the main unit.
2 • Functions as the BAND button while listening to the radio.
Each time you press the button, the band changes.
• Functions as the DISC + button while listening to the CD
changer.
Each time you press the button, the disc number increases,
and the selected disc starts playing.
• Does not function as the PROG button.
3 • Functions as the PRESET button while listening to the
radio.
Each time you press the button, the preset station number
increases, and the selected station is tuned in.
• Functions as the DISC – button while listening to the CD
changer.
Each time you press the button, the disc number decreases,
and the selected disc starts playing.
4 Functions the same as the control dial on the main unit.
Note: These buttons cannot be used for the clock (CLOCK H,
CLOCK M), SCM LINK, LEVEL, B. SKIP and EXT IN
adjustments (see pages 18, 16, 19, 11 and 27).
5 Selects the sound mode.
Each time you press SCM (Sound Control Memory), the mode
changes.
6 Selects the source.
Each time you press FUNC (function), the source changes.
7 • Searches stations while listening to the radio.
• Fast forwards or reverses the track if pressed and held
while listening to a CD.
• Skips to the beginning of the next tracks or goes back to
the beginning of the current (or previous tracks) if pressed
briefly while listening to a CD.
• Functions as the fast forward or rewind buttons or Multi
Music Scan buttons while listening to a tape.
ENGLISH
Using the remote controller
25
EN24-30.KS-FX270[J]/f
25
00.11.10, 10:51 AM
ENGLISH
EXTERNAL COMPONENT OPERATIONS
You can connect the external component to the CD changer jack on the rear using the Line
Input Adaptor KS-U57 (not supplied).
3
1
Preparations:
• For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/
Connection Manual (separate volume).
• Before operating the external component using the following procedure, select the external input
correctly. (See “Selecting the external component to use” on page 27.)
1
Select the external component.
• If “LINE IN” does not appear on the display, see page 27
and select the external input (“EXT IN”).
Note on One-Touch Operation:
When you press CD-CH, the power automatically comes on. You do not have to press
to turn on the power.
2
Turn on the connected device and start playing the source.
3
To turn up the
volume
Adjust the volume.
To turn down
the volume
26
EN24-30.KS-FX270[J]/f
26
00.11.10, 10:51 AM
You can connect the external component to the CD changer jack on the rear using the Line
Input Adaptor KS-U57 (not supplied).
To use the external component as the playback source through this receiver, you need to
select which device — CD changer or external component — to use. When shipped from the
factory, CD changer is selected as the external component.
LINE IN:
To use the external component other than CD changer
CHANGER: To use the CD changer
ENGLISH
Selecting the external component to use
4
2,5
1
3
1
Change the source to FM, AM or TAPE.
2
Press and hold SEL for more than 2 seconds.
“CLOCK H”, “CLOCK M”, “SCM LINK”, “LEVEL”, “B.SKIP”
or “EXT IN” appears on the display.
3
Select “LINE IN” if not shown on the display.
4
Select the desired mode — “LINE IN” or
“CHANGER”.
5
Finish the setting
Note:
• For connecting the Line Input Adaptor KS-U57 and the external component, refer to the
27
Installation/connection Manual (separate volume).
EN24-30.KS-FX270[J]/f
27
00.11.10, 10:51 AM
ENGLISH
MAINTENANCE
To extend the lifetime of the unit
This unit requires very little attention, but you will be able to extend the life of the unit if you
follow the instructions below.
To clean the heads
• Clean the heads after every 10 hours of use using a
wet-type head cleaning tape (available at an audio store).
When the head becomes dirty, you may realize the
following symptoms:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any metallic
or magnetic tools.
To keep the tape clean
• Always store the tapes to their storage cases after use.
• Do not store tapes in the following places:
– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures
CAUTIONS:
• Do not play the tapes with peeling labels; otherwise, they can damage the unit.
• Tighten tapes to remove slack since loose tape may become entangled with the mechanism.
• Do not leave a cassette in the cassette compartment after use, as the tape may become slack.
The function below is also provided to ensure the longer life of this unit.
Ignition key-off Release/Ignition key-on play
• When you turn off the ignition key with a cassette in the compartment, the unit automatically
releases the tape from its head.
• When you turn on the ignition key with a cassette in the compartment, playback automatically
starts.
How to Reset your unit
Press and hold both the SEL (Select) and
(Standby/On/ATT) buttons at the
same time for several seconds.
This will reset the built-in microcomputer.
NOTE: Your preset adjustments — such as preset channels or sound adjustments —
will also be erased.
(Standby/On/ATT)
SEL (Select)
28
EN24-30.KS-FX270[J]/f
28
00.11.10, 10:51 AM
What appears to be trouble is not always serious. Check the following points before calling a
service center.
Symptoms
Causes
Remedies
• A cassette tape cannot be
inserted.
You have tried to insert a
cassette in the wrong way.
• Cassette tapes become hot.
This is not a malfunction.
• Tape sound is at very low
level and sound quality is
degraded.
The tape head is dirty.
Clean it with a head cleaning
tape.
• Sound is sometimes
interrupted.
Connections are not good.
Check the cords and
connections.
• Sound cannot be heard from
the speakers.
The volume control is turned
to the minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• SSM (Strong-station
Sequential Memory)
automatic preset does not
work.
Signals are too weak.
Store stations manually.
• Static noise while listening
to the radio.
The antenna is not connected
firmly.
Connect the antenna firmly.
• “NO CD” or “NO DISC”
appears on the display.
No CD is in the magazine.
Insert CDs into the magazine.
CDs are inserted incorrectly.
Insert them correctly.
This unit is not connected to a
CD changer correctly.
Connect this unit and the CD
changer correctly and press
the reset button of the CD
changer.
• “RESET 8” appears on the
display.
• “RESET 1-RESET 7”
appears on the display.
• The unit does not work at
all.
ENGLISH
TROUBLESHOOTING
Insert the cassette with the
exposed tape facing right.
Press the reset button of the
CD changer.
The built-in microcomputer
may function incorrectly due
to noise, etc.
• The CD changer does not
work at all.
and SEL at
Press
the same time for more than 2
seconds to reset the unit. (The
clock setting and preset
stations stored in memory are
erased.) (See page 28).
29
EN24-30.KS-FX270[J]/f
29
00.11.10, 10:51 AM
ENGLISH
SPECIFICATIONS
AUDIO AMPLIFIER SECTION
CASSETTE DECK SECTION
Maximum Power Output:
Front: 40 W per channel
Rear: 40 W per channel
Continuous Power Output (RMS):
Front: 16 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Rear: 16 W per channel into 4 , 40 Hz
to 20 000 Hz at no more than 0.8%
total harmonic distortion.
Load Impedance: 4 (4 to 8 allowance)
Tone Control Range
Bass: ±10 dB at 100 Hz
Treble:±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedance:
2.0 V/20 k load (250 nWb/m)
Wow & Flutter: 0.11% (WRMS)
Fast-Wind Time: 100 sec. (C-60)
Frequency Response:
30 Hz to 16 000 Hz (± 3 dB)
Signal-to-Noise Ratio: (Normal tape) 56 dB
Stereo Separation: 40 dB
TUNER SECTION
Frequency Range
FM: 87.5 MHz to 107.9 MHz
AM: 530 kHz to 1 710 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 )
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 )
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 1.5 dB
GENERAL
Power Requirement
Operating Voltage: DC 14.4 V (11 V to 16 V
allowance)
Grounding System: Negative ground
Allowable Working Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W x H x D)
Installation Size:
182 mm x 52 mm x 150 mm
(7-3/16" x 2-1/16" x 5-15/16")
Panel Size: 188 mm x 58 mm x 14 mm
(7-7/16" x 2-5/16" x 5/8")
Mass: 1.3 kg (2.9 lbs) (excluding accessories)
Design and specifications subject to change
without notice.
If a kit is necessary for your car, consult
your telephone directory for the nearest
car audio speciality shop.
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
30
EN24-30.KS-FX270[J]/f
30
00.11.10, 10:51 AM
KS-FX270
Installation/Connection Manual
Manual de instalación/conexión
Manuel d’installation/raccordement
GET0008-002A
[J]
V
J
ESPAÑOL
ENGLISH
C
0800HISFLEJES
EN, SP, FR
FRANÇAIS
• This unit is designed to operate on 12 volts DC, NEGATIVE
ground electrical systems.
• Esta unidad está diseñada para funcionar con 12 voltios de
CC, con sistemas eléctricos de masa NEGATIVA.
• Cet appareil est conçu pour fonctionner sur des sources de
courant continu de 12 volts à masse NEGATIVE.
INSTALLATION (IN-DASH
MOUNTING)
INSTALACION (MONTAJE EN EL
TABLERO DE INSTRUMENTOS)
INSTALLATION (MONTAGE DANS LE
TABLEAU DE BORD)
• The following illustration shows a typical installation. However,
you should make adjustments corresponding to your specific
car. If you have any questions or require information regarding
installation kits, consult your JVC car audio dealer or a company
supplying kits.
• La siguiente ilustración muestra una instalación típica. Sin
embargo usted deberá efectuar los ajustes correspondientes
a su automóvil. Si tiene alguna pregunta o necesita información
acerca de las herramientas para instalación, consulte con su
concesionario de JVC de equipos de audio para automóviles o
a una compañía que suministra tales herramientas.
• L’illustration suivante est un exemple d’installation typique.
Cependant, vous devez faire les ajustements correspondant à
votre voiture particulière. Si vous avez des questions ou avez
besoin d’information sur des kits d’installation, consulter votre
revendeur d’autoradios JVC ou une compagnie
d’approvisionnement.
1
2
3
4
5
6
7
8
9
1
Before mounting: Press
(Control Panel Release) to
detach the control panel if already attached.
* When shipped from the factory, the control panel is packed
in the hard case.
Remove the trim plate.
Remove the sleeve after disengaging the sleeve locks.
1 Stand the unit
Note: When you stand the unit, be careful not to damage
the fuse on the rear.
2 Insert the 2 handles between the unit and the sleeve, as
illustrated, to disengage the sleeve locks.
3 Remove the sleeve.
Note: Be sure to keep the handles for future use after
installing the unit.
Install the sleeve in the dashboard.
* After the sleeve is correctly installed in the dashboard,
bend the appropriate tabs to hold the sleeve firmly in place,
as illustrated.
Fix the mounting bolt to the rear of the unit’s body and place
the rubber cushion over the end of the bolt.
Do the required electrical connections explained on the back
of this instructions.
Slide the unit into the sleeve until it is locked.
Attach the trim plate.
Attach the control panel.
2
3
4
5
6
7
8
9
1
Antes de instalar: Pulse
(soltar panel de control) para
separar el panel de control si ya está unido.
* Cuando se envía de la fábrica, el panel de control está
embalado en el estuche duro.
Retire la placa de guarnición.
Retire la manga después de desenganchar los retenes de
la cubierta.
1 Ponga la unidad vertical.
Nota: Al poner la unidad vertical, tenga cuidado de no
dañar el fusible provisto en la parte posterior.
2 Inserte las dos asas entre la unidad y la cubierta tal
como en la ilustración y desenganche los retenes de la
cubierta.
3 Retire la cubierta.
Nota: Después de instalar la unidad, asegúrese de
guardar las asas para uso futuro.
Instale la cubierta en el tablero de instrumentos.
* Después de que la manga esté correctamente instalada
en el tablero de instrumentos, doble las lengüetas
correspondientes para sostener la cubierta firmemente
en su lugar, tal como se muestra.
Fixe el perno de montaje ou la parte trasera del cuerpo de
la unidad y coloque el cojín de goma sobre el extremo del
perno.
Realice las conexiones eléctricas requeridas en base a
las explicaciones que figuran en la parte de atrás de estas
instrucciones.
Deslice la unidad dentro de la cubierta hasta que quede
trabada.
Coloque la placa de guarnición.
Coloque el panel de control.
1
2
3
4
5
6
7
8
9
Avant le montage: Appuyez sur
(déblocage du
panneau de commande) pour éventuellement détacher le
panneau de commande.
* Lorsque ce panneau de commande sort d’usine, il est
rangé dans un étui de transport.
Retirer la plaque d’assemblage.
Libérer les verrous du manchon et retirer le manchon.
1 Poser l’appareil à la verticale.
Remarque: Lorsque vous mettez l’appareil à la verticale,
faire attention de ne pas endommager le fusible situé
sur le fond.
2 Insérer les 2 poignées entre l’appareil et le manchon
comme indiqué pour désengagé les verrous de manchon.
3 Retirer le manchon.
Remarque: S’assurer de garder les poignées pour une
utilisation ultérieur, après l’installation de l’appareil.
Installer le manchon dans le tableau de bord.
* Après installation correcte du manchon dans le tableau
de bord, plier les bonnes pattes pour maintenir fermement
le manchon en place, comme montré.
Monter le boulon de montage sur l’arrière du corps de
l’appareil puis passer l’amortisseur en caoutchouc sur
l’extrémité du boulon.
Réalisez les connexions électriques expliquées au dos de
cette page.
Faire glisser l’appareil dans le manchon jusqu’à ce qu’il soit
verrouillé.
Fixer la plaque d’assemblage.
Remonter le panneau de commande.
Dashboard
Tablero de instrumentos
Tableau de bord
2
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
4
Sleeve
Cubierta
Manchon
3
4*
8
9
10
Fuse
Fusible
Fusible
Slot
Ranura
Fente
Sleeve
Cubierta
Manchon
4m
m
53
5
mm
Mounting bolt
Perno de montaje
Boulon de montage
7
Handle
Manija
Poignée
18
6
See the back page for electrical
connections.
Con respecto a las conexiones
eléctricas, consulte la página de
atrás.
Voir le dos de cette page pour
les connexions électriques.
10
Lock plate
Placa de bloqueo
Plaque de verrouillage
2
Trim plate
Placa de guarnición
Plaque d’assemblage
3
1
1
2
3
4
5
TROUBLESHOOTING
•
*
•
*
•
*
•
*
*
•
*
*
The fuse blows.
Are the red and black leads connected correctly?
Power cannot be turned on.
Is the yellow lead connected?
No sound from the speakers.
Is the speaker output lead short-circuited?
Sound is distorted.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
Unit becomes hot.
Is the speaker output lead grounded?
Are the “–” terminals of L and R speakers grounded in common?
INSTALLATION.KS-FX270[J]/f
1
LOCALIZACION DE AVERIAS
EN CAS DE DIFFICULTÉS
•
*
•
*
•
*
•
*
*
El fusible se quema.
¿Están los conductores rojo y negro correctamente conectados?
No es posible conectar la alimentación.
¿Está el cable amarillo conectado?
No sale sonido de los altavoces.
¿Está el cable de salida del altavoz cortocircuitado?
El sonido presenta distorsión.
¿Está el cable de salida del altavoz conectado a masa?
¿Están los terminales “–” de los altavoces L y R conectados a
una masa común?
• La unidad se calienta.
* ¿Está el cable de salida del altavoz conectado a masa?
* ¿Están los terminales “–” de los altavoces L y R conectados a
una masa común?
10/27/00, 1:30 PM
•
*
•
*
•
*
•
*
*
Le fusible saute.
Les fils rouge et noir sont-ils racordés correctement?
L’appareil ne peut pas être mise sous tension.
Le fil jaune est-elle raccordée?
Pas de son des haut-parleurs.
Le fil de sortie de haut-parleur est-il court-circuité?
Le son est déformé.
Le fil de sortie de haut-parleur est-il à la masse?
Les bornes “–” des haut-parleurs gauche et droit sont-elles mises
ensemble à la masse?
• L’appareil devient chaud.
* Le fil de sortie de haut-parleur est-il à la masse?
* Les bornes “–” des haut-parleurs gauche et droit sont-elles mises
ensemble à la masse?
• When using the optional stay
• Cuando emplea un soporte opcional
• Lors de l’utilisation du hauban en option
• When installing the unit without using the sleeve
• Instalación de la unidad sin utilizar la cubierta
• Lors de l’installation de l’appareil sans utiliser de manchon
In a Toyota for example, first remove the car radio and install the unit in its place.
En un Toyota por ejemplo, primero extraiga la radio del automóvil y luego instale la unidad en su
lugar.
Par exemple dans une Toyota, retirer d’abord l’autoradio et installer l’appareil à la place.
Fire wall
Tabique a prueba de incendios
Cloison
Dashboard
Tablero de instrumentos
Tableau de bord
Stay (option)
Soporte (opción)
Hauban(en option)
Washer
Arandela
Rondelle
Flat type screws (M5 x 6 mm)*
Tornillos tipo plano (M5 x 6 mm)*
Vis à tête plate (M5 x 6 mm)*
* Not included with this unit.
* No suministrado con esta unidad.
* Non fourni avec cet appareil.
Lock nut
Tuerca de seguridad
Ecrou d’arrêt
Screw (option)
Tornillo (opción)
Vis (en option)
Bracket*
Ménsula*
Support*
Mounting bolt
Perno de montaje
Boulon de montage
Pocket
Compartimiento
Poche
Sleeve
Cubierta
Manchon
Bracket*
Ménsula*
Support*
Flat type screws (M5 x 6 mm)*
Tornillos tipo plano (M5 x 6 mm)*
Vis à tête plate (M5 x 6 mm)*
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
Nota: Cuando instala la unidad en la ménsula de montaje, asegúrese de utilizar los tornillos de 6
mm de longitud. Si se utilizan tornillos más largos, éstos pueden dañar la unidad.
Remarque: Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis
d’une longueur de 6 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.
Removing the unit
Extracción de la unidad
Retrait de l’appareil
• Before removing the unit, release the rear section.
• Antes de extraer la unidad, libere la sección trasera.
• Avant de retirer l’appareil, libérer la section arrière.
1
Remove the control panel.
1
Extraiga el panel de control.
1
Retirer le panneau de commande.
2
Remove the trim plate.
2
Retire la placa de guarnición.
2
Retirer la plaque d’assemblage.
3
Insert the 2 handles into the slots, as shown. Then, while gently
pulling the handles away from each other, slide out the unit.
(Be sure to keep the handles after installing it.)
3
Inserte las 2 manijas entre las ranuras, como se muestra.
Luego, separe gentilmente las manijas y extraiga la unidad.
(Asegúrese de conservar las manijas después de
instalarlo.)
3
Introduire les deux poignées dans les fentes, comme montré.
Puis, tout en tirant doucement les poignées écartées, faire
glisser l’appareil pour le sortir. (S’assurer de conserver les
poignées après l’installation de l’appareil.)
1
3
2
Handle
Manija
Poignée
Parts list for installation and connection
Lista de piezas para instalación y conexión
The following parts are provided with this unit.
After checking them, please set them correctly.
Con esta unidad se suministran las siguientes piezas.
Después de inspeccionarlas, colóquelas correctamente.
Hard case/Control Panel
Estuche duro/Panel de control
Etui de transport /Panneau de
command
Liste des pièces pour l’installation et
raccordement
Les pièces suivantes sont fournies avec cet appareil.
Après vérification, veuillez les placer correctement.
Power cord
Cordón de alimentación
Cordon d’alimentation
Lock nut (M5)
Tuerca de seguridad (M5)
Ecrou d’arrêt (M5)
Trim plate
Placa de guarnición
Plaque d’assemblage
Handles
Manijas
Poignées
Mounting bolt (M5 x 20 mm)
Perno de montaje (M5 x 20 mm)
Boulon de montage (M5 x 20 mm)
Sleeve
Cubierta
Manchon
Washer (ø5)
Arandela (ø5)
Rondelle (ø5)
Rubber cushion
Cojín de goma
Amortisseur en caoutchouc
INSTALLATION.KS-FX270[J]/f
2
10/27/00, 1:30 PM
ENGLISH
ESPAÑOL
FRANÇAIS
ELECTRICAL CONNECTIONS
CONEXIONES ELECTRICAS
RACCORDEMENTS ELECTRIQUES
To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections
before installing the unit. If you are not sure how to install this unit
correctly, have it installed by a qualified technician.
Para evitar cortocircuitos, recomendamos que desconecte el
terminal negativo de la batería y que efectúe todas las conexiones
eléctricas antes de instalar la unidad. Si usted no está seguro de
cómo instalar correctamente la unidad, hágala instalar por un
técnico cualificado.
Pour éviter tout court-circuit, nous vous recommandons de
débrancher la borne négative de la batterie et d’effectuer tous les
raccordements électriques avant d’installer l’appareil. Si l’on n’est
pas sûr de pouvoir installer correctement cet appareil, le faire
installer par un technicien qualifié.
Nota:
Esta unidad está diseñada para funcionar con 12 voltios de CC,
con sistemas eléctricos de masa NEGATIVA. Si su vehículo no
posee este sistema, será necesario un inversor de tensión, que
puede ser adquirido en los concesionarios de JVC de equipos
de audio para automóviles.
• Reemplace el fusible por uno con la corriente especificada. Si
el fusible se quemase frecuentemente consulte con su
concesionario de JVC de equipos de audio para automóviles.
• Si el ruido fuese un problema...
Esta unidad tiene un filtro de ruido en el circuito de alimentación.
Sin embargo, en algunos vehículos, pueden producirse
chasquidos u otros ruidos indeseados. En tal caso conecte el
terminal de tierra posterior (Ver diagrama de conexión abajo.)
del receptor al chasis del automóvil, utilizando cordones más
gruesos y cortos tales como alambre de cobre trenzado o de
grueso calibre. Si el ruido persiste, consulte a su concesionario
de JVC de equipos de audio para automóvil.
• La entrada máxima de los altavoces traseros debe ser mayor
de 40 vatios y la de los delanteros de 40 vatios, con una
impedancia de 4 a 8 ohmnios.
• Asegúrese de conectar esta unidad a tierra en el chasis del
automóvil.
• El sumidero térmico estará muy caliente después del uso.
Asegúrese de no tocarlo al desmontar esta unidad.
Remarque:
Cet appareil est conçu pour fonctionner sur des sources de courant
continu de 12 volts à masse NEGATIVE. Si votre véhicule n’offre
pas ce type d’alimentation, il vous faut un convertisseur de tension,
que vous pouvez acheter chez un revendeur d’autoradios JVC.
• Remplacer le fusible par un de la valeur précisée. Si le fusible
saute souvent, consulter votre revendeur d’autoradios JVC.
• Si le bruit est un problème...
Cet appareil incorpore un filtre de bruit dans le circuit
d’alimentation. Cependant, avec certains véhicules, quelques
claquements ou autres bruits non désirés risquent de se produire.
Si cela arrive, raccorder la borne de masse arrière de l’appareil
au châssis de la voiture (voir le schéma de raccordement cidessous) en utilisant des cordons les plus gros et les plus courts
possibles telle qu’une barre de cuivre ou une tresse. Si le bruit
persiste, consulter votre revendeur d’autoradios JVC.
• La puissance admissible des haut-parleurs doit être supérieure
à 40 watts à l’arrière et à 40 watts l’avant, avec une impédance
de 4 à 8 ohms.
• S’assurer de raccorder la mise à la masse de cet appareil
au châssis de la voiture.
• Le radiateur devient très chaud après usage. Faire attention de
ne pas le toucher en retirant cet appareil.
Note:
This unit is designed to operate on 12 volts DC, NEGATIVE
ground electrical systems. If your vehicle does not have this
system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
• Replace the fuse with one of the specified rating. If the fuse
blows frequently, consult your JVC car audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur.
If this happens, connect the unit’s rear ground terminal (See
connection diagram below.) to the car’s chassis using shorter
and thicker cords, such as copper braiding or gauge wire. If noise
still persists, consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 40 watts at
the rear and 40 watts at the front, with an impedance of 4 to 8
ohms.
• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
Heat sink
Sumidero térmico
Dissipateur de chaleur
A Typical Connections / Conexiones típicas / Raccordements typiques
Before connecting: Check the wiring in the vehicle carefully not
to fail in connecting this unit. Incorrect connection may cause a
serious damage to this unit.
1
2
3
Connect the colored leads of the power cord to the car battery,
speakers and automatic antenna (if any) in the following
sequence.
1 Black: ground
2 Yellow: to car battery (constant 12V)
3 Red: to an accessory terminal
4 Blue with white stripe: to automatic antenna (200mA
max.)
5 Others: to speakers
Connect the antenna cord.
Finally connect the wiring harness to the unit.
Antes de la conexión: Verifique atentamente el conexionado
del vehículo para no cometer errores al conectar esta unidad.
Una conexión incorrecta podría producir daños graves en la
unidad.
Avant de commencer la connexion: vérifiez attentivement le
câblage du véhicule pour ne pas connecter incorrectement cet
appareil. Une connexion incorrecte peut endommager
sérieusement l’appareil.
1
Conecte los conductores de color del cable de alimentación
a la batería del automóvil, altavoces y antena automática (si
la hubiere) en la secuencia siguiente.
1 Negro: a tierra.
2 Amarillo: a la batería del automóvil (12V constantes)
3 Rojo: a un terminal de accesorio
4 Azul con rayas blancas: a la antena automática (200mA
máx.)
5 Otros: a los altavoces
1
Connectez les fils de couleur du cordon d’alimentation à la
batterie de la voiture, aux enceintes et à l’antenne automatique
(s’il y en a une) dans l’ordre suivant.
1 Noir: a la masse
2 Jaune: a la batterie de la voiture (12V constant)
3 Rouge: à la prise accessoire
4 Bleu à bandes blanches: à l’antenne automatique (200mA
max.)
5 Autres: aux enceintes
2
3
Conecte el cable de antena.
2
3
Connectez le cordon d’antenne.
Por último, conecte a la unidad el cableado preformado.
* Before connecting the CD changer, make sure that the unit is turned off.
* Antes de conectar el cambiador de CD, asegúrese de que la unidad esté apagada.
* Avant de connecter le chaneur CD, s’assurer que l’unité est éteinte.
Left
Izquierdo
Gauche
When connecting a CD changer, we recommend to use one of the CH-X series CD changers.
• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).
You can also use an external component such as a portable MD player by connecting the Line Input
Adaptor KS-U57 (not supplied). (see diagram B .)
Cuando conecte un cambiador de CD, se recomienda utilizar uno de la serie CH-X.
• Si su cambiador de CD es de la serie KD-MK, necesitará un cable opcional (KS-U15K).
Conectando el adaptador de entrada de línea KS-U57 (no suministrado), también podrá usar un
componente exterior, tal como un reproductor de MD. (Véase el diagrama B ).
Lors de la connexion d’un changeur CD, nous vous recommandons d’utiliser un des changeurs CD de la
série CH-X.
• Si votre changeur appartient à la série KD-MK, vous avez besoin d’un cordon optionnel (KS-U15K).
Vous pouves aussi utiliser un appareil extérieur tel qu’un lecteur de MD en connectant l’adaptateur d’entrée
de ligne KS-U57 (non fourni) (voir le diagramme B ).
JVC CD changer jack
Jack del cambiador de CD de JVC
Prise de changeur CD JVC
Line out
(see diagram B )
Salida de línea
(véase diagrama B )
Sortie de ligne
(voir le diagramme B )
JVC CD changer or
another external
component
Cambiador de CD JVC
u otro componente exterior
Changeur CD JVC ou autre appareil
extérieur
10
Rear ground terminal
Terminal de tierra posterior
Borne arrière de masse
10A fuse
Right
Fusible de 10A
Derecho
Fusible 10A
Droit
Antenna terminal
Terminal de la antena
Borne de l’antenne
Black
Negro
Noire
3
2
To antenna
A la antena
A l’antenne
1
Yellow*1
Amarillo*1
Jaune*1
*1: Before checking the operation of this unit prior to installation,
this lead must be connected, otherwise power cannot be turned
on.
*1: Antes de comprobar el funcionamiento de esta unidad previa
a de la instalación, es necesario conectar este cable, de lo
contrario no se podrá conectar la alimentación.
*1: Pour vérifier le fonctionnement de cet appareil avant
installation, ce fil doit être raccordé, sinon l’appareil ne peut
pas être mis sous tension.
Finalement, connectez le faisceau de fils à l’appareil.
1
2
Red
Rojo
Rouge
*
Ignition switch
Interruptor de encendido
Interrupteur d’allumage
Not included with this unit.
No suministrado con esta unidad.
Non fourni avec cet appareil.
*
To metallic body or chassis of the car
A un cuerpo metálico o chasis del
automóvil
Vers corps métallique ou châssis du
véhicule
*
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition swich).
A A un terminal activo del bloque de fusibles conectado a la
batería del automóvil (desviando el interruptor de encendido)
A une borne sous tension du porte-fusible connectée à la batterie
de la voiture (en dérivant l’interrupteur d’allumage)
3
Blue with white stripe
Azul con rayas blancas
Bleu avec bande blanche
Fuse block
bloque de fusibles
porte-fusible
To an accessory terminal in the fuse block
A un terminal accesorio del bloque de fusibles
Vers borne accessoire du porte-fusible
4
To automatic antenna if any
A la antena automática si la hubiere
Vers borne d’antenne automatique s’il y en a une
5
White with black stripe
Blanco con rayas negras
Blanc avec bande noire
White
Blanco
Blanc
Gray with black stripe
Gris con rayas negras
Gris avec bande noire
Left speaker (front)
Altavoz izquierdo (frontal)
Haut-parleur gauche (avant)
INSTALLATION.KS-FX270[J]/f
3
Gray
Gris
Gris
Green with black stripe
Verde con rayas negras
Vert avec bande noire
Right speaker (front)
Altavoz derecho (frontal)
Haut-parleur droit (avant)
Green
Verde
Vert
Purple with black stripe
Púrpura con rayas negras
Violet avec bande noire
Left speaker (rear)
Altavoz izquierdo (trasero)
Haut-parleur gauche (arrière)
10/27/00, 1:30 PM
Purple
Púrpura
Violet
Right speaker (rear)
Altavoz derecho (trasero)
Haut-parleur droit (arrière)
PRECAUTIONS on power supply and speaker
connections:
• DO NOT connect the speaker leads of the power cord to the
car battery; otherwise, the unit will be seriously damaged.
• Connect the black lead (ground), yellow lead (to car battery,
constant 12V), and red lead (to an accessory terminal) correctly.
• BEFORE connecting the speaker leads of the power cord to
the speakers, check the speaker wiring in your car.
– If the speaker wiring in your car is as illustrated in Fig. 1
and Fig. 2 below, DO NOT connect the unit using that original
speaker wiring. If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect the unit to
the speakers as illustrated in Fig. 3.
– If the speaker wiring in your car is as illustrated in Fig. 3,
you can connect the unit using the original speaker wiring in
your car.
– If you are not sure of the speaker wiring of your car, consult
your car dealer.
+
L -
PRECAUCIONES sobre las conexiones de la
fuente de alimentación y de los altavoces:
PRECAUTIONS sur l’alimentation et la
connexion des enceintes:
• NO conecte los conductores de altavoz del cable de
alimentación a la batería de automóvil, pues podrían producirse
graves daños en la unidad.
• Conecte correctamente el conductor negro (a tierra), el
conductor amarillo (a la batería del automóvil, 12V constantes),
y el conductor rojo (a un terminal de accesorio).
• ANTES de conectar a los altavoces los conductores de altavoz
del cable de alimentación, verifique el conexionado de altavoz
de su automóvil.
– Si el conexionado de altavoz de su automóvil es como
se indica en las Figs. 1 y 2 de abajo, NO conecte la unidad
utilizando ese conexionado de altavoz original. Si lo hace,
se producirán daños graves en la unidad.
Vuelva a efectuar el conexionado de altavoz de manera que
pueda conectar la unidad a los altavoces de la manera
indicada en la Fig.3.
– Si el conexionado de altavoz de su automóvil es como
se indica en la Fig.3, podrá conectar la unidad utilizando el
conexionado de altavoz original de su automóvil.
– Si tiene dudas sobre el conexionado de altavoz de su
automóvil, consulte con su concesionario.
• NE CONNECTEZ PAS les fils d’enceintes du cordon
d’alimentation à la batterie; sinon, l’appareil serait sérieusement
endommagé.
• Connectez correctement le fil noir (a la masse), le fil jaune (a la
batterie de la voiture,12V constant) et le fil rouge (à la prise
accessoire).
• AVANT de connecter les fils d’enceintes du cordon
d’alimentation aux enceintes, vérifiez le câblage des enceintes
de votre voiture.
– Si le câblage des enceintes de votre voiture est réalisé
comme montré sur la Fig. 1 ou Fig. 2 ci-dessous, NE
CONNECTEZ PAS l’appareil en utilisant ce câblage original
d’enceintes. Si vous le faites, l’appareil sera sérieusement
endommagé.
Recommencez le câblage des enceintes de façon que vous
puissiez connecter l’appareil aux enceintes comme montré
sur la Fig. 3.
– Si le câblage des enceintes de votre voiture est comme
montré sur la Fig. 3, vous pouvez connecter l’appareil en
utilisant ce câblage original d’enceintes pour votre voiture.
– Si vous n’êtes pas sûrs du câblage d’enceintes de votre
voiture, consulter le concessionnaire de votre voiture.
+
+
L -
-
+
R -
+
+
+
R -
-
Fig. 1
+
L -
-
+
+
-
+
R -
-
Fig. 2
+
-
Fig. 3
Connecting the leads / Conexión de los conductores / Raccordement des fils
Solder the core wires to
connect them securely.
Suelde los alambres de alma
para conectarlos con firmeza.
Souder les âmes desfils pour
les raccorder entre eux de
façon sûre.
Twist the core wires when connecting.
Retuerza los alambres de alma para
conectarlos.
Torsader les âmes des fils en les raccordant.
CAUTION / PRECAUCION / PRECAUTION:
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating
tape.
• Para evitar cortocircuitos, cubra los cables NO UTILIZADOS con cinta aislante.
• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS utilisés
avec de la bande isolante
B Connections Adding Other Equipment / Conexiones para añadir otros equipos / Raccordement pour ajouter d’autres appareils
You can connect an amplifier and other equipment to upgrade
your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
• For amplifier only:
– Connect this unit’s line-out terminals to the amplifier’s line-in
terminals.
– Disconnect the speakers from this unit, connect them
to the amplifier. Leave the speaker leads of this unit
unused. (Cover the terminals of the these unused leads
with insulating tape, as illustrated above.)
Usted podrá conectar un amplificador y ostros equipos para
mejorar el sistema estéreo de su automóvil.
• Conecte el cable remoto (azul con rayas blancas) al cable
remoto del otro equipo para que pueda ser controlado a través
de esta unidad.
• Sólo para el amplificador:
– Conecte los terminales de salida de línea de esta unidad con
los terminales de entrada de línea del amplificador.
– Desconecte los altavoces de esta unidad y conéctelos al
amplificador. Los cables de los altavoces de esta unidad
quedan sin usar. (Cubra los terminales de estos cables
sin usar con cinta aislante, tal comose indica en la figura
de arriba).
Vous pouvez connecter un amplificateur ou autre appareil pour
améliorer votre systéme autoradio.
• Connecter le fil d’alimentation à distance (bleu avec des bandes
blanches) au fil d’alimentation à distance de l’autre appareil
de façon qu’il puisse être controlé par cet appareil.
• Pour l’amplificateur seulement:
– Raccorder les bornes de sortie ligne de cet appareil aux bornes
d’entrée ligne de l’amplificateur.
– Déconnectez les enceintes de cet appareil et connectezles à l’amplificateur. Laissez les fils d’enceintes de cet
appareil inutilisés. (Recouvrir les extrémités de ces fils
inutilisés avec de la bande isolante comme montré cidessus.)
Amplifier / Amplificador / Amplificateur
Rear speakers
Altavoces posteriores
Haut-parleur arrière
L
INPUT
L
R
R
Blue with white stripe
Azul con rayas blancas
Bleu avec bande blanche
JVC amplifier
Amplificador de JVC
Amplificateur JVC
Y-connector (not supplied with this unit)
Conector en Y (no suministrado con esta unidad)
Connecteur Y (non fourni avec cet appareil)
Remote lead
Cable remoto
Fil d’alimentation à distance
To automatic antenna if any
A la antena automática, si la hubiere
Vers l’antenne automatique, s’il y en a une
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
LINE OUT
L
L
R
R
KS-FX270
REAR
Front speakers
Altavoces delanteros
Haut-parleur avant
External component / Componente exterior / Appareil extérieur
Line Input Adaptor KS-U57 (not supplied with this unit)
Adaptador de entrada de línea KS-U57 (no suministrado con esta unidad)
Adaptateur d’entrée de ligne KS-U57 (non fourni avec cet appareil)
L
L
L
L
R
R
R
R
LINE OUT
L
REAR
R
KS-FX270
CD changer jack
Toma del cambiador de CD
Prise du changeur CD
INSTALLATION.KS-FX270[J]/f
4
Signal cord (not supplied with this unit)
Cable de señal (no suministrado con esta unidad)
Cordon de signal (non fourni avec cet appareil)
10/27/00, 1:30 PM
External component
Componente exteríor
Appareil extérieur
http://www.jvcmobile.com
Visit us on-line for
Technical Support & Customer Satisfaction Survey.
US RESIDENTS ONLY
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to Reset
Still having trouble??
USA ONLY
Call 1-800-252-5722
http://www.jvcservice.com
We can help you!
VICTOR COMPANY OF JAPAN, LIMITED
V
EN, SP, FR
EN00.COVER.KS-FX270[J]/f
J
2
C
0800HISFLEJES
10/27/00, 3:51 PM