Download Craftsman 917.377991 Owner`s manual
Transcript
Owner's Manual IVlllM° E ROTARY LAWN MOWER Model No. 917.377991 o o o - Safety Assembly Operation Maintenance EspaSoi Repair Parts CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment Sears, Roebuck and Co., Hoffman Estates, IL 60179 Visit our Craftsman website: www_sears,com/craftsman Warranty Safety Rules Assembly Operation Maintenance Schedule Maintenance 2 2 4 6 t0 10 Product Specifications Service and Adjustments Storage Troubleshooting Repair Parts Parts Ordering 11 14 16 17 37 Back Cover LIMITED TWO YEAR WARRANTY ON CRAFTSMAN POWER MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears wil! repair free of charge any defect in material or workmanship. If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This Warranty does not cover: • Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug. o Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual. Warranty sen,ice is available by returning the Craftsman power mower to the nearest Sears Service Center/Department in the United States. This warranty applies only while this product is in use in the United States. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179 Safety standards require operator presence controls to minimize the risk of injury_ Your unit is equipped with such controls. Do not attempt to defeat the function of the operator presence controls under any circumstances. TRAINING; ° Read this operator's manual carefully. Become familiar with the controls and know how to operate your mower properly° Learn how to quickly stop mower. , Do not allow children to use your mower. Never allow adults to use mower without proper instructions° o Keep the area of operation clear of all persons, especially small children and pets. , Use mower only as the manufacturer intended and as described in this manual • Do not operate mower if it has been dropped or damaged in any manner. Always have damage repaired before using your mower° ° Do not use accessory attachments that are not recommended by the manufacturer. Use of such attachments may be hazardous. ° The blade turns when the engine is running. PREPARATION" ° Always thoroughly check the area to be mowed and clear it of all stones, sticks, wires, bones, and other foreign objects. These objects will be thrown by the blade and can cause severe injury. ° Always wear safety glasses or eye shields when starting and while using your mower. ° Dress properly. Do not operate mower when barefoot or wearing open sandals. Wear only solid shoes with good traction 2 when mowing. o Checkfuel tank before startingengine. Do not fill gas tank indoors,when the engine is runningor when the engine is hot, Allow the engineto cool for several minutes beforefilling the gas tank. Clean off any spilled gasoline beforestarting the engine. o Always make wheel height adjustments beforestarting your mower. Never attemptto do this while the engine is running. • Mow only in daylightor good artificial lighL OPERATION: o Keep your eyes and mind on "your mower andthe area being cut. Do not let o Never cut grass by pulling the mower towards you° Mow across the face of slopes, never up and down or you might lose your footing. Do not mow excessively steep slope& Use caution when operating the mower on uneven terrain or when changing directions maintain good footing. o Never operate your mower without proper guards, plates, grass catcher or other safety devices Jnp_ace. MAINTENANCE AND STORAGE: ° Check the blade and the engine mounting bolts often to be sure they are tightened properly. o Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condition° ° Keep all safety devices in place and working° ° To reduce fire hazard, keep the engine free of grass, leaves or excessive grease and oil. - Check grass catcher often for deterioration and wear and replace worn bags. Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower. ° Always keep a sharp blade on your mower° ° Allow engine to cool before storing in any enclosure. - Never store mower with fuel in the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc. other interests distract you. o Do not mow wet or slippery grass. Never run while operating your mower. Always be sure of your footing -- keep a firm hold on the handles and walk. ° Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all time& ° Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, walks, roads, and any gravel--covered areas. ° Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it. ° Before cleaning, inspecting, or repairing your mower, stop the engine and make absolutely sure the blade and all moving parts have stopped. Then disconnect the spark plug wire and keep it away from the spark plug to prevent accidental starting, ° Do not continue to run your mower if you hit a foreign object. Follow the procedure outlined above, then repair any damage before restarting and operating you mower° o Do not change the governor settings or overspeed the engine. Engine damage or personal injury may result. o Do not operate your mower if it vibrates abnormally. Excessive vibration is an indication of damage; stop the engine, safely check for the cause of vibration and repair as required ° Do not run the engine indoors. Exhaust fumes are dangerous° ALook for this symbol to point out important safety precautions. It means CAUTION!!! BECOME ALERT!!! YOUR SAFETY IS INVOLVED° _I,CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. AWARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 3 These accessories were available when this lawn mower was produced. They are not shipped with your mower. They are also available at most Sears retail outlets and service centers. Most Sears stores can atso order repair parts for you, when you provide the model number of your lawn mower. Some of these accessories may not apply to your lawn mower. LAWN,,M, OWER PERFORMANCE CLIPPING , illllllllll DEFLECTOR FOR REAR DISCHARGE STABILIZER MULCHER KITS LAWN MOWERS f- GRASS CATCHERS FOR REAR DISCHARGE LAWN MOWERS lu GRASS CATCHERS FOR SIDE DISCHARGE LAWN MOWERS GAS CANS LAWN MOWER MAINTENANCE ...... ,,, u, .,.i BELTS MUFFLERS SPARK PLUGS AIR FILTERS lu i ,..ul BLADES i i BLADE ADAPTERS WHEELS TO REMOVE CARION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower, IMPORTANT: This lawn mower is shipped WITHOUT OiL OR GASOLINE in the engine, ",(our new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your lawn mower, at! parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to ensure proper tightness. ENGINE OIL LAWN MOWER FROM • Remove loose parts included with mower. o Cut down two end comers of carton and lay end panel down flat, o Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle. ° Roll lawn mower out of carton and check carton thoroughly for additional loose parts. 4 HOW TO SET UP YOUR LAWN MOWER TO INSTALL ATTACHMENTS TO UNFOLD HANDLE Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging: ,, Open rear door and remove mulcher plug. Store mulcher plug in a safe place. o You can now install catcher or optional clipping deflector_ o To retum to mulching operation, install mulcher plug into discharge opening of mower° Be sure all tabs are seated properly. IMPORTANT: Unfold handles carefully so as not to pinch or damage control cables_ • Raise handles until lower handle section locks into place in mowing position. = Remove protective padding, raise upper handle section into place on lower handle and tighten both handle knobs. ° Remove handle padding holding operator presence control bar to upper handle° ° Your lawn mower handle can be adjusted for your mowing comfort. Refer to "Adjust Handle" in the Service and Adjustment section of this manual Operator presence control bar Upper handle "-_ //// uftup \//!L Lift Mulcher plug up _'__"-_,_/_=_ ._ / ACAUTION: Do not run your lawn mower without mulcher plug in place or approved clipping deflector or grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open. Mowing position Lower handle 5 KNOW YOUR LAWN MOWER READ THIS OWNER'S MANUALAND SAFETY RULES BEFORE OPERATING YOUR LAWN MOWER, Compare the illustrations with your lawn mower to familiarize yourself with the location of various controls and adiustments. Save this manual for future reference. These symbolsmay appearon your lawn mower or in literature suppliedv_lf=tfle product.Learn and understand theremeaning. CAUTION OR WARNING ENGINE ON ENGINE OFF FAST SLOW CHOKE Engine zone control cable FUEL OIL DANGER, KEEP HANDS AND FEET AWAY Operator presence control bar Drive control lever Starter handle Handle knob Grass Engine oil cap w! dipstick Mulcher plug Housing Drive cover Gasoline cap Primer IMPORTANT: 3_is lawn mower is shipped WITHOUT OIL OR GASOLINE in the engine. Wheel adjuster (on each wheel) MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U,S° Consumer Product Safety Commission. The blade tums when the engine is running, Drive control lever - used to engage powerpropelled forward motion of lawn mower. Mulcher plug - must be removed to convert to bagging or discharging operation. Operator presence control bar - must be held down to the handle to start the engine. Release to stop the engine. Primer - pumps additional fuel from the carburetorto the cylinderfor use when starting a cold engine. Starter handle- used for starting the engine. 6 The operation of any lawn mower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your lawn mower or performing any adjustments or repairs° We recommend a wide vision safety mask over spectacles or standard safety glasses. HOWTO USEYOUR LAWN MOWER "ENGINE SPEED The engine speed was set at the factory for optimum performance. Speed is not adjustable. ENGINE ZONE CONTROL &CAUTION: .Federal regulations require an engine control to be installea on this lawn mower in order to minimize the risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running° • Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned behind the lawn mower handle to start and operate the lawn mower. TO ADJUST CUTTING HEIGHT o Raise wheels for low cut and lower wheels for high cut. • Adjust cutting height to suit your requirements. Medium position is best for most lawns. ° To change cutting height, squeeze adjuster lever toward wheel Move wheel up or down to suit your requirements. Be sure all wheels are in the same setting. NOTE; Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs. Plate Tab LowerWheelsf°rHighC_o._b.__,.__._. __ Raise Wheels for Low Cut Lever TO ATTACH GRASS CATCHER ° Close the lift top tid_ Lift top lid must be closed while operating lawn mower° ° Lift the rear door on the mower housing and place the grass catcher frame onto the formed tabs on the rear door hinge bracket. ° The grass catcher is secured to the lawn mower housing when the rear door is lowered onto the grass catcher frame, ACAUTION: Do not run your lawn mower without clipping deflector or approved grass catcher in place_ Never attempt to operate the lawn mower with the rear door removed or propped open. Hinge bracket Rear door Grass catcher frame Formed tabs TO EMPTY GRASS CATCHER • To remove grass catcher, release operator presence control bar to stop engine° ° Lift up rear door and remove the grass catcher by the handle. NOTE: Do not drag the bag when emptying; it will cause unnecessary wear° DRIVE CONTROL o Self-propelling is controlled by holding the operator presence control bar down to the handle and pushing the drive ADD GASOLINE o FTttfuel tank° Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. control lever forward until it clicks; then release the lever. ° Forward motion will stop when the operator presence control bar is released. To stop forward motion without stopping engine, release the operator presence control bar slightly until the drive control disengages° Hold operator presence control bar down to handle to continue mowing without selfpropelling. o To keep drive control engaged when turning corners, push down on handle and lift front wheels off ground while turning lawn mower. Operator presence control bar _WARNING: Experience indicates that alcohol blended fLiels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty° Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may Drive control occur. ACAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. To engage drive control Drive control disengaged Gasoline filler cap BEFORE STARTING ENGINE OIL Your lawn mower is shipped without oil in the engine. • Be sure mower is level and area around oil fill is clean. ° Remove engine oil cap and fill to the full line on the dipstick. NOTE: Allow oil to settle down into engine for accurate dipstick reading, • Engine holds 27 oz& of oil. For type and grade of oil to use, see "ENGINE" in Maintenance section of this manual. ° Pour oi! slowly. Do not over fill. ° Check oil level before each use. Add oil if needed. Fill to full line on dipstick. • To read proper level, tighten engine oil cap each time. ° Reinstall engine oil cap and tighten. ° Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirty conditions. Engine oil cap TO START ENGINE ° To start a cold engine, push primer three (3) times before trying to start° Use a firm push. This step is not usually necessary when starting an engine which has already run for a few minutes. ° Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back. • To stop engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not start° If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. 8 MOWING MULCHING MOWING TIPS TIPS o Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings It may also be necessary to reduce ground speed and/or run the lawn mower over the area a second time, o For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly. o For better grass bagging and most cutting conditions, the engine speed should be set in the fast position. o When using a rear discharge lawn mower in moist, heavy grass, clumps of cut grass may not enter the grass catcher. Reduce ground speed (pushing speed) and/or run the lawn mower over the area a second time_ ° if a trail of clippings is left on the right side of a rear discharge mower, mow in a clockwise direction with a small overlap to collect the clippings on the next pass. • Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dpj before using. o Keep top of engine around starter clear and clean of grass clippings and chaff° This will help engine air flow and extend engine life, IMPORTANT; For best performance, keep mower housing free of built-up grass and trash. See "Cleaning" in Maintenance section of this manual,. o The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn, Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. • Avoid cutting your lawn when it is wet. Wet grass tends to form clumps and interferes with the mulching action. The best time to mow your lawn is the eady aftemoon_ At this time the grass has dried and the newly cut area will not be exposed to the direct sun_ ° For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely hearty mulching, reduce your width of cut by overlapping previously cut path and mow slowly° o Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings° When doing a second cut, mow across or perpendicular to the first cut path. ° Change your cutting pattern from week to week. Mow north to south one week then change to east to west the next week, This will help prevent matting and graining of the lawn. Max 1/3 9 FILL IN DATES AS YOU COMPLETE /__J_" _,-_ _ .,_'%?_-'Y_.q_" ........ €heck for Loose Fasteners clear,Jlnspect Grass Catcher (If Equipped) M .Clean Lawn Mower O (Power-Propelled Clean Under Drive Mowers) Cover Check drive beitipuiieys $/ ,k-_. _ 5k_ _'49"_ _ _ SERVICE DATES , 64_ v" ...... v' (P0we.r.rprop.eIled Mowe rs) ChecldSharpen/RepTac e Blade Lubrication Chart E Clean Battery/Recharge (Electric Start Mowers! ........ C.heck Engine Oil Level U G C.hange Engine Oil Clean Air Filter I N inspect Muffler C! ean 9_ ReP(ace Spark Piug E Replace Air Filter Paper Cartridge 12 3 4 - ........... _ _, _4 ..... ,,., . .,,....,.,, Mi' i_' 2 ........ ........ ..... . = 6/ II/ IV# 2 Change more often when operating under a heavy load or in high ambient temperatures Service more oflen when opera_ng in dirty or dusly conditions Replace blades more often when mowtng tn sandy soil Charge 48 hours at end of season. GENERAL RECOMMENDATIONS LUBRICATION The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual° Some adjustments will need to be made periodically to properly maintain your unit° All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. o Once a year, replace the spark plug, replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assures proper air-fuel mixture and helps your engine run better and last longer. - Follow the maintenance schedule in this manual. BEFORE EACH USE ° Check engine oil level. ° Check for loose fasteners. LUBRICATION Keep unit well lubricated TION CHART")° (See "LUBRICA- CHART (_ Wheel adjuster Engine oil Rear door hinge L'_ HandIe bracket mounting pin ["_'_.)Spray lubricant (_) Refer to Maintenance "ENGINE" section, IMPORTAI'tl': Do not oil or grease plastic wheel bearings. Viscous lubricants will attract dust and dirt that will shorten the life of the self lubricating bearings, tf you feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly. 10 PRODUCT SPECiFiCATiONS MODEL NUMBER SERIALNUMBER DATE OF PURCHASE GASOLINE CAPACITY/TYPE: 917.37799t OI LTYPE (API-SF/SGtSH): SAE 30 (ABOVE 32°F) SAE 5W-30 (BELOW 32°F) 27 OZS. CHAMPION RJ19LM OR J19LM INTAKE: °004 - ,008 EXHAUST: .004 - .008 1 o5QUARTS UNLEADED REGULAR OIL CAPACITY: SPARK PLUG (GAP: VALVE CLEARANCE: ,030") SOLID STATE IGNITION AIR GAP: BLADE BOLT TORQUE: .0125 IN. 35-40 FTo LBS. o 'The modeJ and"seriai numbers wiirbe found on a decal attach'ed to th8 rear o{_the lawn mower housing.Record both serial number and date of purchase in space provided above, LAWN MOWER Always observe safety rules when performing any maintenance° TIRES . Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. ° Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results, mower blade must be kept sharp° Replace bent or damaged blades. TO REMOVE BLADE • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug. ° Turn lawn mower on its side. Make sure air filter and carburetor are up. • Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt, = Protect your hands with gloves and!or wrap blade with heavy cloth. - Remove blade bolt by tuming counter.. clockwise. - Remove blade and attaching hardware (bolt, lock washer and hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged, TO REPLACE BLADE * Position the blade adapter on the engine crankshaft° Be sure key in adapter and crankshaft keyway are aligned, o Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter. o Be sure the trailing edge of blade (opposite sharp edge) is up toward the engine. ° Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft. o Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise. ° The recommended tightening torque is 35-40 ft. Ibs. 11 IMPORTANT: treated. Blade bolt is grade 8 heat TO SHARPEN BLADE NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. Care should be taken to keep the blade balanced_ An unbalanced blade wilt cause eventual damage to lawn mower or engine. ° The blade can be sharpened with a file or on a gdnding wheel. Do not attempt to sharpen while on the mower. * To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail exposed_ Place center hole of blade over the head of the nail. tf blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced° Crank shaft Blade keyway ada Key Blade o Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth. o Put wheels back in place. • If after cleaning, the drive wheels do not turn freely, contact your nearest authorized service center. GEAR CASE o To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season. ° The gear case is filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case_ • If lubricant is required, use only Texaco Starplex Premium 1 Grease, Part No. 750369. Do not substitute. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SF, SG or SH_ Select the oil's SAE viscosity grade according to your expected operating temperature_ SAE VISCOSITY GRADES Crank ",, Lock washer Hardened washer sha_ edge 4 I_ll Blade °F: adapter '=C -3p" GRASS CATCHER ° The grass catcher may be hosed with water, but must be dry when used. • Check your grass catcher often for damage or deterioration. Through normal use it will wear. If catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering. DRIVE WHEELS Check front drive wheels each time before you mow to be sure they move freely. The wheels not turning freely means trash, grass cuttings, etco are in the drive wheel area and must be cleaned to free drive wheels. if necessary to clean the drive wheels, check both front wheels. = Remove hubcaps, hairpin cotters and washers. = Remove wheels from wheel adjusters. " :20" i_1_1 llllllill ............. 0" ' .:,2D' ,-,"lO" TEMPERATURE 30; ) 32" 40' O' RANGE ANTICIPA3"EO 60" 1137 BEFORE "' 80" 20" 100" ..... 30* 4C,' NEXT OIL CHANGE NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°E Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 25 hours of operation or at least once a year if the lawn mower is not used for 25 hours in one year. Check the crankcase oi! level before starting the engine and after each five (5) hours of continuous use_ Tighten oil plug securely each time you check the oil level_ 12 TO CHANGE ENGINE OIL NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty. o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug. o Remove engine oil cap; lay aside on a clean surface. • Tip lawn mower on its side as shown and drain oil into a suitable container. Rc#k lawn mower back and forth to remove any oil trapped inside of engine. o Wipe off any spilled oil on lawn mower and on side of engine. • Fit! engine with oil Fill only to the "FULL" line on the dipstick. DO NOT overfill. , Replace engine oil cap. o Reconnect spark plug wire to spark plug. lner AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter. Replace the air filter every year, more often if you mow in very dusty, dirty conditions. Do not wash air filter. TO CHANGE AIR FILTER o Loosen cover knob, . Swing cover down and remove from hinge. • Pull paper filter out of air cleaner body. ° Clean air cleaner cover and body° • Install a new paper filter. o Reinstall cover to air cleaner body. Be sure hinge is assembled properly. o Swing cover up and tighten cover knob. (Do not overtighten). MUFFLER Inspect and replace corroded muffler as it could create a fire hazard and/or damage, SPARK PLUG Change your spark plug each year to make your engine start easier and run better. Set spark plug gap at .030 inch° CLEANING IMPORTANT: For best performance, keep mower housing free of built-up grass and trash Clean the underside of your mower after each use. ,_CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with the spark plug. • Turn lawn mower on its side. Make sure air filter and carburetor are upo Clean the underside of your lawn mower by scraping to remove build-up of grass and trash. o Clean engine often to keep trash from accumulating. A clogged engine nJns hotter and shortens engine life. • Keep finished surfaces and wheels free of all gasoline, oil,etc, ° We do not recommend using a garden hose to clean lawn mower unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in shortened engine life. CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a season. Scrape underside of cover with putty knife or similar toot to remove any build-up of trash or grass on underside of drive cover. Hinge Air filter cover Paper filter Cover knob '13 ACAUTION: Before performing any service and adjustments: o Release control bar and stop engine° ° Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug, LAWN MOWER TO ADJUST CUTTING HEIGHT See 'q-O ADJUST CUTTING HEIGHT' in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your lawn mower, is provided to minimize the possibility that objects will be thrown out the rear of the lawn mower into the operator's mowing position. If the rear deflector becomes damaged, it should be replaced. TO REMOVEfREPLACE DRIVE BELT TO ADJUST HANDLE The handle can be mounted in a high or low position, The mounting holes in the bottom of lower handle are off center for raising or lowering the handle, o Remove upper handle and all parts attached to lower handle, ° Remove hairpin cotters from lower handle bracket mounting pin. ° Squeeze lower handle in to remove it from mounting pins. - Turn lower handle over to raise or lower handle. o Squeeze lower handle in and position holes onto mounting pins on handle bracket. • Reassemble upper handle and all parts removed from lower handle_ Mowing position ° Remove drive cover. Remove belt by pushing down on gear case pulley and roll belt off_ ° Turn lawn mower on its side with carburetor and fuel cap up. , Remove blade. • Remove debris shield. ° Remove belt from engine pulley on crankshaft. o Install new belt by reversing above steps. o Always use factory approved belt to assure fit and long life. ,-, ,<.'_ Mowing position ., ,(-.-;; r--I High position Low position Drive cover _',," Belt _ Lower Push down Rotate _ 14 handle TO ASSEMBLE GRASS CATCHER o insert leg of tubular frame through front opening of grass catcher and thread frame into sewn hem of bag. NOTE: Keep bag hem gathered on the straight leg of the tubular frame. o When frame comes out the other end of sewn hem, immediately work the end of frame down inside the bag as shown in inset. o Slide sewn hem evenly around the tubular frame until both ends of frame are exposed out of the front opening. • Assemble lower frame to tubular frame as shown° Be sure handle is outside of bag and frames are fully seated as shown in inset. o Slip vinyl bindings over frame° NOTE: If vinyl bindings are too stiff, hold them in warm water for a few minutes° If bag gets wet, let it dry before using° ° Close the flip lid. Flip lid must be closed while operating lawn mower. ,&CAUTION: Do not run your lawn mower without clipping deflector or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open_ ENGINE Sewn Tubular frame Sewn hem hem Fli_ !_d Lower frame (Frames must be i fully seated) Tubular frame SPEED Lower frame handle Your engine speed has been factory set, Do not attempt to increase engine speed or it may result in personal injury° If you believe that the engine is running too fast or too slow, take your lawn mower to an authorized service center for repair and adjustment. CARBURETOR Your carburetor has a non-adjustable fixed main jet for mixture control° If your engine does not operate properly due to suspected carburetor problems, take your lawn mower to an authorized service center for repair and/or adjustment. IMPORTANT: never tamper with the engine governor, which is factory set for proper engine speed_ Overspeeding the engine above the factory high speed setting can be dangerou& if you think the engine-governed high speed needs adjusting, contact your nearest authorzed service center, which has proper equipment and experience to make any necessary adjustments. 15 Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more. Fo,d foward . . ,or storage LAV_JMOWER When lawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. • Clean entire lawn mower (See "CLEANING" in the Maintenance section of this manual)° • Lubricate as shown in the Maintenance section of this manual. ° Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary. ° Touch up all rusted or chipped paint surfaces; sand lightly before painting. HANDLE You can fold your lawn mower handle for storage. o Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward. o Loosen upper handle mounting bolts enough to allow upper handle to be folded back. IMPORTANT: When folding the handle for storage or transportation, be sure to fold the handle as shown or you any damage the control cables. ° When setting up your handle from the storage position, the lower handle will automatically lock into the mowing position. Lower //// _'_.._, ,Y ".__.f'_ ,,, ,//_ Fo a Lower __ handle Mowing position ENGINE FUELSYSTEM IMPORTANT: It is important to prevent gum deposits from forming in essential fuel system parts such as carburetor, f fuel filter, fuel hose or tank during storage. Also, experience indicates that alcohol blended fuels ( called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. • Drain the fuel tank. • Start the engine and let it run until the fuel lines and carburetor are empty. o Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. , Use fresh fuel next season. NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer. handle Handle bracket Squeeze to fold Upper handle Operator presence control . bari Hairpin cotter 16 ENGINEOIL Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the Maintenance section of this manual). CYLINDER ° Remove spark plugo ,, Pour one ounce (29 ml) of oil through spark plug hole into cylinder_ o Pull starter handle slowly a few times to distribute oil. ° Replace with new spark plug. OTHER ° Do not store gasoline from one season to another. TROUBLESHOOTING PRO"BLEi_ Does not start o Replace your gasoline can if your can starts to rusL Rust and/or dirt in your gasoline wilt cause problems. o If possible, store your unit indoors and cover it to give protection from dust and dirt. • Cover your unit with a suitable protective cover that does not retain moisture° Do not use plastic. Plastic cannot breathe which allows condensation to form and wil! cause your unit to rust. IMPORTANT: Never cover mower while engine and exhaust areas are still warm. ACAUTION: Never store the lawn mower with gasoline in the tank inside a building where fumes may reach an open flame or spark_ Allow the engine to cool before storing in any enclosure. CHART CAUSE CORRECTION 1o Clean/replace air filter. 2. Fill fuel tank_ 3. Drain tank and refill with fresh clean fuel 4. Drain fuel tank and carburetor and refill tank 1, Dirty air filter° 2. Out of fuelo 3o Stale fuelo 4. Water in fuel. 5. 5_ Spark plug wire is disconnected. 6, Bad spark plug. Loose blade or broken blade 7_ adapter° 8o Control bar in released & position. 9. Control bar defective° 9. 6. 7. with fresh gasoline° Connect wire to plug. Replace spark plug. Tighten blade bolt or replace blade adapter. Depress control bar to handle. Replace control bar. ..... ,,, ,,,,,,,,,.... Loss of power 1. 2. 3. 4. 5. 6. Rear of lawn mower housing 1_ Set to"Higher Cut" or cutting blade dragging position. in heavy grass_ 2. Set to "Higher Cut" Cutting too much grass. position. 3_ Clean/replace air filter. Dirty air _ter. 4. Clean underside of mower Buildup of grass, leaves, and trash under mower. housing_ 5. Check oil level° Too much oil in engine. 6. Cut at slower walking Walking speed too fast° speed_ ............ Poor cut- uneven ,i,i, i ill ii,,,im. H,,Ill 1o Worn, bent or loose blade_ 1. 2. Wheel heights uneven. 2. Buildup of grass, leaves and trash under mower. 3. 3_ 17 ...................................... Replace blade_ Tighten blade bolto Set all wheels at same height Clean underside of mower housing. TROUBLESHOOTING PROBLEM Excessive vibration CHART CAUSE CORRECTION 1, Worn, bent or loose blade. 2. Bent engine crankshafL Starter rope hard to pull . 1o Replace blade, Tighten blade bolt, 2, Contact an authorized service center. Engine flywheel brake is on 1. when control bar is released. 2_ Bent engine crankshafL 2. 3, 4. Blade adapter broken. Blade dragging in gras& 3. 4. Depress control bar to upper handle before pulling starter rope. Contact an authorized service center. Replace blade adapter, Move lawn mower to cut grass or to hard surface. Loss of drive I, 2. , , ,,,,, ,,, , Drive wheels not tuming with drive control engaged° Belt not driving 1, 2, Adjust or replace drive control cable. Put belt on pulleys or replace belts if broken, = Grass catcher not filling (if so equipped) 1o Cutting height too low. 2, Lift on blade worn off, Hard to push 1, 3. .............. Catcher not venting air, ,.............................. Raise cutting height° Replace blade. Clean grass catcher. ,,,,,,,,,,,, ,,,, 2, Grass is too high or wheel height is too tow, Rear of lawn mower 3. housing or blade dragging in grass. Grass catcher too full. 4. 1, 2, 3, Handle height position not right for you, 18 1_ Raise cutting height. 2, 3, 4, Raise rear of lawn mower housing one (1) setting higher. Empty grass catcher° Adjust handle height to suit, Garantia 19 Especificaciones Reglas de Seguridad Montaje Operaci6n Mantenimiento 19 21 23 27 Servicio y Adjustes Afmacenamiento Identificaci6n de problemas Partesde repuesto Programa 27 de Mantenimiento Orden de Partes del Produclo 28 31 33 34 Vea el manual ingl6s del duefio Contratapa GARANT[A LIMITADA DE DOS ArT, lOS PARA LA SEGADORAA MOTOR CRAFTSMAN Por dos (2) aSos, a parUr de la fecha de compra, cuando esta Segadora Craftsman se mantenga, lubrique y aline segDn Ias instrucciones para la operaci6n y el mantenimiento en el manual del due_o, Sears repararA gratis todo defecto en el material y la mano de obra. Si la Segadora Craftsman se usa para fines comerciales o de arriendo, esta garantfa s61ose aplica por noventa (90) dfas a partir de la fecha de compra. Esta Garantfa no cubre: o Articulos que se desgastan durante el uso normal tales como las cuchitlas segadoras rotatorias, los adaptadores de la cuchilla, las correas, los filtros de aire y las bujias. - Reparaciones necesarias debido af abuso o a la negligencia del operador, incfuy_ndose a los cigQeSales doblados y a ia falta de mantenimiento del equipo seg{3n las instrucciones que se incluyen en el manual del duefio. EL SERVICIO DE GARANTfA ESTA DISPONIBLE al devolver la segadpra a motor Craftsman al Centro/ Departmento de Servicio Sears mas cercano en los Estados Unidos,. Esta garantia se aplica solamente mientras el producto este en uso en los Estados Unidoso Esta Garantia le otorga derechos legates especificos, y puede que tambi6n tenga otros derechos que vaffan de estado a estado. Sears, Roebuck and Co., Di817WA, Hoffman Estates, IL 60179 USA Los estandrares de seguridad exigen la presencia del operator en los controles para reducir a un minimo el riesgo de lesionarse,. Su unidad viene equipada con dichos controles. Por ningun motivo irate del eliminar ta funci6n de los controles que exigen la presencia de! operador. ENTRENAMIENTO: o Lea este manual del operador cuidadosamente. Familiadcese con los controles y aprenda a operar su segadora en forrna adecuada. Aprenda a parar su segadora rApidamente. . No permita que los niRos usen su segadorao Nunca permita que los adultos operen la segadora sin contar con las instrucciones adecuadas. ° Mantenga el Area de operaci6n despejada de gente, especialmente de nifios pequeSos y de animales dom6sticos. ° Use la segadora solarnente para los fines propuestos por el fabricante y seg0n las expHcaciones descritas en este manual, * No opere ta segadora si se ha cafdo o daSado en cualquiera formao Siempre repare los daSos antes de usada, ° No use accesorios que no hayan sido recomendados por el fabricante, El uso de dichos accesorios puede ser peligroso,, ° La cuchilla gira cuando el motor estA funcionando. PREPARAOION: ° Siempre revise cuidadosamente el Area que se va a segar y desp_jela de todas las piedras, palos, alambres, huesos y otros objetos extrafios. Estos objetos serAn lanzados con la cuchilla y pueden producir lesiones graves° ° Siempre use anteojos de seguridad o protectores de ojos cuando arranque y durante el tiempo que use la segadora. ° Vfstase en forma adecuadao No opere fa segadora sin zapatos o con sandalias mientras que el motor estA funcionandoo 19 • Revise el estanque de combustible antes de hacer arrancar el motor° No Ilene el estanque de gasolina en recintos cerrados, ni cuando el motor ester funcionando o cuando est#. caliente. Permita que et motor se enfrie pot varios minutos antes de Ilenar el estanque de gasolina_ Limpie toda la gasottna derramada antes de hacer arrancar el motor° o Siempre haga los ajustes de altura de las ruedas antes de hacer arrancar su segadora. Nunca trate de hacer 6sto mientras que el motor est,_ funcionando. ° Siegue siempre durante el dia o con buena luz artificial° OPERACI6N: ° Mantenga sus ojos y su mente en ta segadora y en el ,_rea que se est_ cortando. No permita que otros intereses Io distraigan. ° No corte c_sped mojado o resbalosoo Nunca corra mientras est6 operando su segadora. Siempre asegL_rese de mantener el equitibrio - mantenga el mango agarrado firmemente y camine_ o No ponga las manos o los pies cerca odebajo de las partes rotatorias. Mant6ngase alejado de la abertura de descarga en todo momento. o Siempre pare el motor cuando se vaya ocuando no est_ usando su segadora, o antes de atravesar las entradas para autos, los senderos, caminos y _reas cubiertas de ripioo - Nunca dirija la descarga del material hacia los espectadores ni permita a nadie cerca de la segadora mientras la est_ operando. o Antes de limpiar, inspeccionar o de reparar 1 a segadora, pare el motor y est6 completamente seguro de que la cuchi!la y que todas las partes que se mueven se hayan detenido_ Luego, desconecte et alambre de la bujfa y mant_ngalo alejado de Osta para evitar el arranque por accidente. • No continL3e haciendo funcionar su segadora si le pega a un objeto extrafioo Siga el procedimiento descrito anteriormente, luego repare cualquier dafio antes de volver a arrancar y de operar su segadora. ° No cambie los ajustes del regulador o hagaque el motor ande a una velocidad excesiva. Se pueden producir daSos en et motor y t esiones personales. • No opere su segadora si vibra fuera de Io normal La vibraciSn excesiva es una indicaci6n de daSo; pare el motor, revise en forma segura la causa de la vibraci6n y haga las reparaciones segL_n sea necesario. ° No haga funcionar el motor en recintoscerrados. Los gase_ de escape son peligrososo o Nunca corte el c_sped tirando la segadora hacia ustedo Siegue a tray,s de la cam de las pendientes, nunca hacia arriba o hacia abajo pues puede perder el equilibrio. No siegue pendientes demasiado empinadaso Tenga cuidado cuando opere la segadora en terreno disparejo o cuando cambie de direcciSn - mantenga un buen equilibrioo = Nunca opere la segadora sin las protecciones adecuadas, las planchas, el recogedor de c_sped y otros dispositivos de seguridad en su lugaro MANTENIMIENTO Y ALMACENAMIENTO: o Revise la cuchilla y los pernos de montaje del motor a menudo, para asegurarse que est_n apretados en la forma adecuadao ° Revise todos los pemos, tuercas y tomillos a inter#alos frecuentes, para verificar si est&n apretados en forma adecuada, y asegurarseque la segadora se encuentra en condiciones de funcionamiento seguro. ° Mantenga todos los dispositivos de seguridad en su lugar y listos para funcionaro ° Para reducir el peligro de incendio, mantenga el motor sin c6sped, hojas y grasa o aceite en excesoo ° Revise el recogedor de c_sped a menudo para vefificar si hay deterloro y desgaste y cambie las bolsas desgastadaso Use solamente fas bolsas de repuesto recomendadas por el fabricante de su segadora o que cumplen con tas especificaciones de _steo ° Siempre mantenga una cuchilJa afilada en su segadora. ° Siempre permita que el motor se enfri'e antes de guardarla en cualquier recinto cerradoo ° Nunca guarde la segadora con combustible en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una fuente de igniciSn, tal como el calentador de agua, la estufa de calefacciSn, la secadora de ropa, etco _Busque este simbolo que seSala las precauciones de seguridad, de impor-tancia° Quiere decir - iiiATENCION!!! iiiESTE ALERTO!!! SU SEGURtDAD ESTA COMPROMETIDA. _,PRECAUCI6N: Siempre desconecte el alambre de la bujfa y p6ngalo donde no pueda entrar en contacto con la buj[a, para evitar el arranque por accidente, durante la preparaci6n, el transporte, el ajuste o cuando se hacen reparaciones. _PRECAUCI6N: Es conocido por el Estado de California que los gases de escape del motor de este productor contienen qufmicos los cuales a ciertos niveies, pueden ocasionar, c&ncer, defectos de nacimiento, y otros daSos al sistema reproductivo. 2O Estos accesorios estaban disponibtes cuando se produio la segadora. No son facilitados junto al cortacesped. Tambi6n estAn disponibles en la mayor{a de las tiendas de Sears yen los centros de servicio. La mayorfa de las tiendas Sears tambi6n pueden mandar a pedir partes de repuesto para usted, si les propordona el nQmero del modelo de su segador& Atgunos de estos accesorios tal vez no se apiiquen a su segador& RENDIMIENTO DE LA SEGADORA " DESVIADOR PARA SEGADORAS € f ..... DE RECORTES CON DESCARGA TRASERA JUEGOS ii ii ii ill PARA iiJ,Hu., LA ACOLCHADORA RECOREDOR PARA ESTABtLIZADORES PARA SEGADORAS CON DESCARGA RECOREDOR LATERAL SEGADORAS CON DESCARGA TRASERA ENVASES DE GASOLINA ..... MANTENIMIENTO SILENCIADORES CORREAS ,ul i DE LA SEGADORA FILTROS ....................... CUCHILLAS ADAPTADORES DE CUCHILLA Lea estas instrucciones y este manual completamente antes de tratar de montar u operar su segadora nueva,. IMPORTANTE: Este cortacesped viene SIN ACEITE O GASOLINA en el motor. Su segadora nueva ha sido montada en la f&bdca con la excepci6n de aquellas partes que se dejaron sin montar por razones de envio. Todas las partes como las tuercas, las arandelas, los pemos, etc., que son necesarias para completar el montaje han sido colocadas en la bolsa de parte& Para asegurarse que su segadora funcione en forma segura y adecuada, todas las partes y los articulos de ferreteri'a que se monten tienen que ser apretados seguramente. Use tas herramientas correct.as, como sea necesarb, para asegurar que se apfieten adecuadamente. BUJ{AS DE AIRE RUEDAS ACEITE DEL MOTOR • Remueva todo el material de empaque, excepto ia cura entre el mango superior y _I inferior, y la curia que sujeta la barra de los controt que exige la presencia del operador junto con e! mango superior, ° Haga rodar la segadora hacia afuera de fa caja de cart6n y revfsela cuidadosamente para verificar si todavfa quedan partes sueltas adidonales. COMO PREPARAR SU SEGADORA PARA DESDOBLAR EL MANGO IMPORTANTE: Despliegue el mango con mucho cuidado para no pellizcar o dariar los cables de control° • Levante los mangos hasta que la secci6n del mango inferior se asegure en su lugar, en la posici6n para segaro ° Remueva la curia protectora, levante la secci6n del mango superior hasta su lugar en el mango inferior, y apriete ambas manillas del mango_ • Remueva la curia del mango que sujeta la barra de los control que exige la presencia del operador junto con el mango superior, PARA REMOVER LA SEGADORA DE LA CAJA DE CARTON • Remueva las partes sueltas que se incluyen con la segador& = Corte las dos esquinas de los extremos de la caja de cart6n y tienda el panel del extremo piano. 21 Elmangodela segadora puedeajustarse segt'Jn leacomodeparasegar.Refi6rase a "AJUSTE DEL MANGO" en la Secd6n de Ser¢icio y Ajustes de este manual Barra de control que exige la presencia del operador Mango superior Levant__ ''_ PARA INSTALAR LOS ACCESORIOS Su segadora fue enviada lista para usarse oomo una acolchadora de capa vegetal° Para convertirla de modo que pueda ensacar o descargar: = Abra fa puerta trasera y remueva la tapon acolchadora. GuArdeta en un lugar seguro. • Ahora puede instalar el recogedor o el desviador de recortes opcional o • Para volver a la operaci6n de acolchamiento con capa vegetal, instale la tapon acolchadora en la abertura de descarga de la segadora, AsegQrese de que todas las orejas est_n asentadas en forrna adecuada. oslct6n para segar inferior Tapon acolchadora _,PRECAUCI6N: No haga funcionar su segadora sin la tapon acolchadora aprobada en su lugar, o sin el desviador de recortes, o sin e! recogedor de c6sped, aprobados, en su lugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando est,, un poco abiertao FAMILIARICESE CON SU SEGADORA LEA ESTE MANUAL DEL DUENO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU SEGADORA. Compare las ilustraciones con su segadora para familiarizarse con la ubicaci6n de los d!verso.s controles y ajustes: Guarde este manu.at' para referenc!a.._e, r_el futuro. .............................................................................. "Estos simbolos pueden apareser sobre su segadora o en la literatura proporcionada con el producto. Aprenda y comprenda sus significados. I\l ATTENCION O ADVERTENCIA MOTOR ENCENDIDO MOTOR R/_PIDO LENTO ESTRANGU COM- LAC_6N BUSTIBLE ACE{TE PELIGRO, GUARDE LAS MANOS Y LOS PIES LEJOS APAGADO control que exige la presencia del operador Cable de control de zona del motor Control de impulsiSn CordSn Manilla del Ta deposito de aceite det motor con varilla indicadora de nivel mango Recogedor del c_sped Cubierta de la imputsiSn Ajustador de la rueda (en cada rueda) Tapon de la acotchadora Tapa del deposito de la gasolina Cebador Caja IMPORTANT= Este cortacesped viene SIN ACEITE O GASOLINA en el motor° 111 CUMPLE CON ....................... LOS REQUISITOS .L I_I=,I,sEGUR;,_AD DE LA CPSC Las segadoras a motor, que se conducen desde la parte de atr_.s, rotatorias, Sears, cumplen con los estdndares de seguridad del American National Standards Institute y de la U.S. Consumer Product Safety Commission. La cuchilla gira cuando el motor est,_ funcionando. i[,,,111111111 Barra de control que exige la prencia del operador - tiene que sujetar-se abajo, junto con el mango, para hacer arrancar el motor° Su_ltela para parar el motor. Cebador - bombea combustible adicional desde el carburador al cilindro para uso cuando se necesita hacer arrancar un motor ffio. Cord6n arrancador arrancar el motor° Palanca de control de la impulsi6n - se usa para enganchar ta segadora para movimiento hacia adelante impulsada a motor° Tapon de la acolchadora - situada en la abertura de la descarga y debe ser quitada cuando se convierte la operacciSn de ensacado a descarga. - se usa para hacer 23 La operaciSn de cualquier segadora puede hacer que salten objetos extra5os dentro de sus ojos, Io que puede producir dafios graves en 6stos. Siempre use anteojos de seguridad o protecciSn para los ojos mientras opere su segadora o cuando haga ajustes o reparacioneso Recornendamos una mascara de seguridad de visiSn amplia, para uso espejuetos o anteojos de seguridad estandarte. COMO USAR SU SEGADORA VELOOIDAB Orejas de la Para un corte alto, baje las ruedas Mango Para un corte bajo, levante las ruedas PARA MONTAR Y ADJUNTAR EL RECOGEDOR DE OF.SPED o Cierre la tapa soltable,, La tapa soltable debe estar cerrada cuando se esta operando la segadora. • Levante la pueda trasera de la caja de la segadora y ponga el bastidor del recogedor de c6sped en las orejas formadas en el puntal de bisagra de la pueda trasera. • El recogedor de c6sped esta asegurado en la caja de la segadora cuando se baja la puerta trasera para descansar en el bastidor del recogedor de c6sped DEL MOTOR La velocidad del motor se estableci6 en la f&brica para un rendimiento 6ptimo,. La velocidad no se puede ajustar,. CONTROL DE ZONA DEL MOTOR _PREOAUOI6N: Las regulaciones federales exigen que se instale un control para el motor en esta segadora para reducir a un mfnimo el riesgo de lesionarse debido al contacto con la cuchilla. Por ningOn motivo trate de eliminar la funci6n del control del operadoro La cuchilla gira cuando el motor est_ funcionando. _PR,ECAUCI6N: No haga funcionar su sega(]ora sin el desviaaor ae recortes o sin el recogedor de c6sped, aprobados, en su lugaro Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando estA un poco abierta. • Su segadora viene equipada con una barra de control que exige la presencia del operador, Io que requiere queet operador est6 detr_s del mango de la segadora para haceda arrancar y operad& PARA AJUSTAR LA ALTURA DE CORTE Pue_a o Levante las ruedas para el corte bajo y baje las ruedas para el corte alto. o Ajuste la altura de corte para que se acomode a sus requisitoso La posid6n del medic es la mejor para la mayofia de los c6spedes. • Para cambiar ta altura de corte, empuje la palanca del ajustador hacia la rued& Mueva la rueda hacia arriba o hacia abajo de modo que se acomode a sus requisitos. AsegOrese que todas las ruedas queden igualmente ajustadas, AVISO: E! ajustador esta correctamente colocado cuando las orejas de la plata est_.n insedadas en el agujero del mango. Tambi_n, los ajustes de 9 posiciones (si equipado) permiten que el mango pueda ser movido entre las orejas de la placao Bastidordel reogedordel cesped PARA VACIAR EL RECOGEDOR ClaSPED DE = Para remover el recogedor del c_sped, pare el motor at aliviar la barra de control que exige la presencia del operador. = Levante la puerta de atras y remora el recogedor del c6sped por el mango. AVISO' No permita que el recogedor arrastrado cuando io vaci6; puede ocasionarse dafios. 24 sea AGREGUE CONTROL DE LA IMPULSION o La autoimpulsi6n se controla al sujetar la barra de control que exige la presencia del operador hacia abajo en el mango y al empujar la palanca de control de la impulsi6n hada adelante hasta que suene "clic," luego se suelta la palancao o El movimiento hacia adelante parar_, cuando la barra de control que exige la presencia de! operador se sueita. Para parar el movimiento hacia adelante sin parar el motor, suelte la barra de control que exige la presencia de! operador un poco hasta que se desenganche el control de la impulsi6n.. Sujete la barra de control que exige la presencia del operador abajo en contra del mango para continuar segando sin autoimpulsi6n° o Para mantener el control de la impulsi6n enganchado cuando se de vuelta en las esquinas, empuje el mango hacia abajo y levante las ruedas delanteras fuera del suelo al girar la segadora. Barra de control que Control de exige la presencia del..., la impulsi6n operador\4\ " 1\ '_ _, Connt,;01de la _ impulsiSn \_ Para enganchar el Control de la impulsi6n control de la imputsi6n desenganchado ANTES DE HACER ARRANCAR EL M_)TOR ACEITE Su segadora fue enviada sin aceite en el motor. • Aseg_rese que la segadora est@nivelada y que el _rea alrededor det depSsito de aceite est6 limpia. ° Remueva ta tapa del dep6sito de aceite del motor y retlene hasta la linea de lteno en @sta. AVtSO: Permitir quel aceite se asiente bien en el motor para ler bien su niveL • El motor puede contener 27 oz. de aceite. Para el tipo y la calidad vea "MOTOR" en la secci6n de las Mantenimento en este manual,. • Vacfe el aceite lentamenteo No Io llene demasiado. ° Revise el nivel del aceite antes de cada uso. Agregue aceite si es necesafio. Uene hasta la Ifnea de Ileno en la vafilla indicadora de nivelo ° Para leer el nivel adecuado, apriete la tapa del dep6sito de aceite del motor cada vezo ° Vuelva a instalar ta tapa del dep6sito del aceite y apfi_tela. ° Cambie el aceite despu6s de 25 horas de operaci6n o una vez por temporada,. Puede necesitar cambiar el aceite m_.s a menudo cuando ias condiciones son polvorosas o sucias. 25 GAsOLINA • Llene el estanque de combustible_ Use gasofina regular, sin plomo, nueva y timpia con el mfnimo de 87 octanos_ No mezcle el aceite con la gasolina. Para asegurar que la gasolina utilizada sea fresca compre estanques los cuales puedan ser utilizados durante los primeros 30 dfas, _h,ADVERTENCIA: La exl?eriencia ha indicado que los combust=bles mezclados con alcohol (conocidos como gasohol, o el uso de etanol o metanol) pueden atraer la humedad, la que conduce a la separaci6n y formaciSn de &cidos durante el almacenamiento,. La gasolina acidica puede dafiar el sistema del combustible de un motor durante el almacenamiento, Para evitar los problemas con el motor, se debe vaciar el sistema del combustible antes de guardarlo por un peri'odo de 30 d[as o m_s. 'v'ac[e el estanque del combustible, haga arrancar el motor y h_.galo funcionar hasta que las I[neas del combustible y el carburador queden vac[os. La pr6xima temporada use combustible nuevo. Vea las lnstrucciones Para El Almacenamiento para m_s informaci6n,. Nunca use productos de limpieza para el motor o para el carburador en el estanque del combustible pues se pueden producir dafios permanentes,. _PRECAUClON: Llene hasta la parte inferior del cueilo de relteno del estanque de gasolina_ No lo Ilene demasiado. Limpie el aceite o el combustible derramado. No almacene, derrame o use gasolina cerca de una llama expuesta. Tapa del deposito de la gasolina Tapa del deposito de _aceite /motor det PARA HACER ARRANCAR EL MOTOR ° Para hacer arrancar un motor frfo, empuje et cebador tres (3) veces antes de tratado,, Empuje firmemente. Este paso normalmente no es necesado cuando se hace arrancar un motor que ya ha estado funcionando por unos cuantos minutoso ° Sujete la barra de control que exige la presencia del operador abajo en el mango y tire el mango del arrancador r_pidamente_ No permita que el cordSn arrancador se devuelva abruptamenteo • Para parar el motor, suelte la barra de control que exige la presencia del operadoro AVlSO:En climasm&sfr/ospuedequesea necesariorepetirlos pasosdetcebado._ En climasm_.scalurososel cebardemasiado puedeproducirel ahogoy el motornova a arrancar.Si se ahogael motorespereunos cuantosminutosantesde tratarde hacerlo arrancary no repitalos pasosdel cebadoo CONSEJOS PARA SEGAR o Bajo ciertas condiciones, tal como c_sped muy alto, puede ser necesario el elevar la altura del corte para reducir el esfuerzo necesario para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c6sped,, Puede que sea necesario reducir la velocidad del recorrido y/o haga funcionar la segadora sobre el _.rea pot segunda vez, ° Para un corte muy pesado, reduzca el ancho del code pasando parcialmente por encima del lugar anteriormente cortado y siegue lentamente. o Para un mejor ensacado del c6sped y para la mayoda de las condiciones de corte, la velocidad del motor debe ajustarse a la posici6n de r&pido. o Cuando use una segadora con descarga trasera en c6sped hSmedo y pesado, los montones del c6sped cortado puede que no entren en el recogedor de c6sped. Reduzca ta velocidad del recorrido (vetocidad de empuje) yio haga funcionar la segadora sobre el _.rea por segunda VeZo o Si queda una huella de cortes en el lado derecho de una segadora con descarga trasera, siegue en la direcci6n en que giran las manillas del reloj, solapando un poco para recaudar los recortes en la pr6xima pasada. o Los poros en los recogedores de c6sped de tela pueden Ilenarse con mugre y polvo con el uso y los recogedores recaudar_n menos c6sped. Para evitar _sto, roc[e el recogedor con la manguera de agua regularmente y d_jelo secarse antes de usarlo. ° Mantenga la parle superior del motor, alrededor del arrancador, despejada y sin recortes de c_sped y paja. Esto ayudarb, el flujo del aire del motor y extender=5 su duraci6n. CONSEJOS PARA SEGAR Y ACOLCHAR IMPORTANTE: Para obtener e[ mejor rendimeinto mantenga la caja de la segador a sin acumlacion de cesped y basura. Vea "UMPIEZA" en seccion de"Mantenimento" de este manual.. ° La cuchilla acolchadora especial va a vo[ver a cofl,ar los recortes de c6sped muchas veces, y los reduce en tamafio, de modo que si se caen en el c_sped se van a dispesar entre _ste y no se van a notar. Tambi_n, el c&sped aco]chado se va a deshacer r,_pidamente entregando substancias nutritivas para el c_sped. Siempre acolche con la velocidad del motor (cuchilla) m_.s alta, pues as[ se obtendrA la mejor acci6n de recorte de las cuchitlaso • E_.4tecortar el c_sped cuando est6 mojado, El c_sped mojado tiende a formar montones e intediere con la acci6n de acolchado_ La mejor hora para segar el c_sped es temprano en la tarde. A esa hora _ste se ha secado y el ,_rea reci6n cortada no quedara expuesta al sol directo. , Para obtener los mejores resultados, ajuste la aitura del corte de la segadora de modo que _sta corte solamente el tercio superior de las hojas de c_sped. En el caso de que el c_sped haya crecido demasiado, puede set necesario el eievar la altura del corte para reducir el esfuerzo necesario para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c_spedo Para un acolchamiento muy pesado, reduzca el ancho del corte pasando por encima del lugar anterion'nente cortado y siegue lentamente. ° Ciertos tipos de c&sped y sus condiciones pueden exigir que un eirea tenga que ser acolchada por segunda vez para esconder completamente los recortes. Cuando se haga el segundo corte, siegue atravesado o en forma perpendiculara la pasada del primer corte_ o Cambie su patr6n de corte de semana a semanao Siegue de norte a sur una semana y luego cambie de este a oeste la prSxima semanao Esto evitar_ que el c&sped se enrede y cambie de direcci6no Max. 1/3 26 PROGRAMA DE MANTENIMIENTO LLENE LAS FECHAS A MEDIDA QUE COMPLETE SU SERVICIO REGULAR FECHAS DE SERVlClO i I Revisar el n!vei de! aceite 1Carnbiar el aceite del motor .......... C_! Inspeccionar v' el si|enciador i U pi ,ro cambiar buj a 6#42 F .!i Cambiar el cartucho de papal del firtro de,,aire ............ Camblar m_s a menudo cuando se opere baio carga pesada o en ambientes con alias temperaturas - Dar servlcio m&s a menudo cuando sa opera en condiciones sucias o polvorasas - Cambte 1as cuchilias m&s a rnenudo cuando slegue en terreno arenoso Cargar per 48 horas al fin de ta temporada, TABLA DE LUBRICACION RECOMENDACIONES GENERALES La garantia de esta segadora no cubre los artfcutos que han estado sujetos al abuso o a la negligencia del operador. Para recibir todo el valor de ta garantfa, el operador tiene qua mantener la segadora segt_n las instrucciones descritas en este manual. Ajustador de la rueda Aceite del motor Hay algunos ajustes que se tienen que hacer en farina peri6dica para poder mantener su unidad adecuadamenteo Todos los ajustes en la secci6n de Servicio y Ajustes de este manual tienen queser revisados par Io menos un vez par cada temporada. • Una vez at ar3o, cambie la bujia, timpie o cambie el elemento del filtro de aire y revise si la cuchilla est_ desgastada. Una bujfa nueva y un elemento del filtro de aire limpio/ nuevo aseguran la mezcla de aire-combustible adecuada y ayudan a que su motor funcione major y que dure m#,so • Slga e! programa de mantenimiento en este manual. ANTES DE CADA usa , Revise el nivef del aceite del motor° ° Revise si hay sujetadores LUBRICACION sueltos_ Mantenga la unidad bien lubricada (vea la "TABLA DE LUBRtCACI6N"). Bisagra de la puerta trasera (_ Clavija de montaje del puntal del mango (_ ROCIE EL LUBRICANTE (_ REFIERASE A LA SECCION DE MANTENtMENTO EN "MOTOR" IMPORTANTE: No acedto engrase los rodamientos de la rueda de plastico. Los lubricantes viscosos atraeran polve y mugra, 1o qua acortara la duracion de los rodamientos auto lubricantes. Si cree qua lubficarse, use sotamente un lubdcante tipo grafito, de polve 27seco, en farina moderada.. t ESPECIFICACIONES DEL PRODUCTO NOMERO DE MODELO NUMERO DE SERIE FECHA DE COMPRA CAPACIDAD Y TIPO DE GASOLINA: T1PO DE ACEITE: CAPACIDAD B'0JiA 115 cUa_os ........ REGULAR SIN PLOMO SAE 30 (sobre 32°F) SAE 5W-30 (debajo 32°F) 27 oz. de capacidad CHAMPION RJ19LM o J19LM ADMISION: .004- .008 DESCARGA: .004- .008 DE ACEKTE: (ABERTURAI TOLERANCIA 917.377991 .030") DE VALVULA: SENCENDIDO DE ESTADO SOLIDO ABERTURA DE AIRE: .0125 TORsi'6N DEE PERNO DE LA CUCHILLA: 35-40 F'T, LBS. IN. • El num_ro del nodelo y el de serie se encuentran en la calcomania adjunta a la parte trasera de la caja de la segadora, Debe registrar tanto el num6ro de serie come la fecha de compra y mantengalos en un lugar seguro para refencia en el futuro. SEGADORA AVISO: Remueva el adaptador de la cuchitla y revise e! cubo interior de la ranura del adaptador de la cuchilla. La ranura tiene que estar en buenas condiciones para que funcione en forma adecuada, Cambie el adaptador si est& daSadoo Siempre observe INs reglas de seguridad cuando haga et mantenimiento,, LLANTAS = Mantenga INS Ilantas sin gasolina, aceite o substandas qufmicas para control de insectos que pueden daRar la goma. ,, E'Z#.elos tocones, tas piedras, INS grietas profundas, los objetos afilados y otros peligros que pueden daSar a INs llantas. CUIDADO DE LA CUCHILLA PARA . ° ° ° = ° LA CUCHILLA ° Ponga el adaptador de la cuchilla en el ciguefial del motor. AsegL_rese que la ranura del adaptador y que el chavetero del ciguefial est6n alineadoso ° Ponga la cuchilla en e} adaptador de _sta alineando los dos (2) agujeros en la cuchilla con INS salientes elevadas en el adaptadoro ° Asegurese de que el borde de salida de la cuchilla (opuesto al borde afilado) est6 hacia arriba hacia el motor. o Instale el pemo de la cuchilla con la arandela de segufldad y la arandela endurecida en el adaptador de la cuchilla y el cigue_al. ° Use un bloque de madera entre la cuchilla y la caja de la segadora y apriete el perno de la cuchilla gir_ndolo en et sentido en que giran las manillas del reloj. • La torsi6n para apretar recomendada es de 35 - 40 pies ltbras. Para obtener los mejores resultados, la cuchilla de la segadora tienen que mantenerse afilada. Cambie la cuchilla doblada o daSada. PARA REMOVER CAMBIAR LA CUCHILLA Desconecte el alambre de la bujfa y pSnga!o en donde no pueda entrar en contacto con _sta, Haga descansar la segadora en su lado., Aseg_rese que el filtro de Mire y que e! carburador queden mirando hacia arriba. Use un bloque de madera entre la cuchilla y la caja de la segadora para evitar que la cuchilla gire cuando se le quite el pemo. Proteja sus manos con guantes y/o envuelva la cuchitla con una teta gruesao Remueva el perno de la cuchilla gir_ndolo en el sentido contrario en que giran INS manitlas del reloj. Remueva ta cuchilla y los art[culos de ferreterfa adjuntadores (el pemo, la arandela de seguridad y la arandela endurecida). IMPORTANTE: El perno de la cuchifla es clase 8 tratado a calor. 28 PARA AFILAR LA CUCHILLA AVlSO: No recomendamos et afilar la cuchilla pero si Io hace, aseg_Jrese de que quede balanceada. Se tiene que tener cuidado de mantenerla balanceada. Una cuchilla que no est& balanceada va a producir eventualmente daSo en la segadora o en el motor° , La cuchilla puede afilarse con una lima o en una rueda rectificadora No trate de afilarla mientras se encuentra en la segadorao o Para revisar el balance de la cuchilla, clave un clavo en una viga o en la pared Deje alrededor de una pulgada de un clavo recto expuesto Ponga el agujero central de la cuchilla sobre la cabeza del clavo Si la cuchilla est& balanceada debe permanecer en la posiciSn horizontal. Si cualquiera de los extremos de la cuchilla se mueve hacia abajo, afile e! extremo pesado hasta que 6sta quede balanceada Adaptador de la Cuchilla Chavetero del ° Si se necesita lubricante, use solamente Grasa Texaco Starplex Premium 1, Parle No 750369° No use substitutos_ RUEDAS DE IMPULSI6N Revise las ruedas de impulsi6n delanteras cada vez antes de segar, para asegurarse de que se mueven libremente. Si tas ruedas no giran libremente quiere decir que hay basura, recortes de c6sped, etc. en el _.rea de las nJedas de impulsi6n y tienen que limpiarse para liberarlaso Es necesario iimpiar las ruedas de impulsi6n; revise ambas ruedas delanteraso o Remueva los tapacubos, las clavijas de horquilla y las arandelas ° Remueva fas ruedas de los ajustadores de las ruedas. o Remueva la basura y los recortes de c_sped de dentro de la cubierta contra el polvo, pifi6n y/ o de los dientes de los engranajes de ias ruedas de impulsi6n ° Ponga las ruedas de vuelta en su lugaro ° Si despu6s de limpiar las nJedas de impulsi6n no giran ]ibremente, p6ngase en contacto con su centro!departamento de servido autofizado m_s cercano MOTOR LUBRlCACI6N Use solamente aceite de detergente de alta calidad clasificado con la clasificaci6n SF SG O SH de servicio APt. Seleccione la calidad de viscosidad SAE segt_n su temperatura operaci6n esperada. de CALIDADEs DE VISCOSIDAD DE SAE RECOGEDOR IE/i_ 41iml/l_m DE CESPED • El recogedor de c_sped puede ser rociado con el agua de la manguera pero tiene que estar seco cuando se vaya a usar. ° Revise su recogedor de c6sped a menudo para verificar si est_ da_ado o deteriorado. Se va a _C -30 ° ,_J_'DE ._I_ -_O" O" 10" _{P 3(_ 411" I TEMPERATURA ANTICtPADA ANTES iOELPROXIMO CAMBIO DE ACEiTE AVtSO: A pesar de que los aceites de multiviscosidad (5W30, 10W30, etco) mejoran el arranque en cfima fr[o, estos aceites de multiviscosidad van ha aumentar el consumo de aceite cuando se usan en temperaturas sobre 32 ° F. Revise el nivel del aceite del motor m,_s a menudo, para evitar un posible daSo en el motor, debido a que no tiene suficiente aceite. desgastar con el uso normal. Si se necesita cambiar el recogedor, c_mbielo sotamente per uno que sea aprobado por el fabricante D6 el n_3merodel modelo de la segadora cuando Io ordeneo CAJA DE ENGRANAJES ° Para mantener el sistema de impulsi6n flJncionando en forma adecuada, ta caja de engranajes y el ,_rea alrededor de la impulsi6n tienen que mantenerse limpias y sin acumulad6n de basura Limpie debajo de la cubierta de la impulsi6n dos veces por temporada ,, La caja de engranajes se Ilena con lubricante hasta el nivel adecuado en la f_brica. La enica vez que el lubdcante necesita atenci6n es cuando se le ha prestado servicio a la caja de engranajeso Cambie el aceite despu_s de 25 horas de operaci6n o por Io menos una vez al a_o si la segadora se utitiza menos 25 horas el a5oo Revise el nivel del aceite del c_rter antes de arrancar el motor y despu_s de cada cinco (5) horas de uso continuado Apriete el tap6n del aceite en forma segura cada vez que revise el nivel del aceite. 29 PARA CAMBIAR EL ACEITE DEL MOTOR AViSO: Antes de incliner la segadora para drenar el aceite, drene el tanque de combustible haciendo correr e! motor haste que el tanque est6 vacio. • Desconecte el alambre de la bujfa y p6ngalo de modo que no pueda entrar en contacto con 6sta. . Remueva la tapa del dep6sito det aceite; d_jela a un lado en una supefficie limpia. ° Incline la segadora y h&gela descansar en su lado y drene el aceite en un envase adecuadoo Mueva la segadora de atrgts para adelante para remover todo el aceite que se haya quedado atrapado dentro det motor° o Ltmpie todo el aceite derramado en la segadora yen el lado del motor° o Llene el motor con aceite. Ll_nelo solamente haste la Iinea de lleno (FULL) en la variUa indicadora de nivel,, NO LO LLENE DEMASIADQ ° Vuetva a poner la tapa en el dep6sito del aceite_ ° Vuelva a conectar et alambre de la bujfa a 6sta, Acubierta del Bisagra Fiitro de papel SILENOIADOR Inspeccione y cambie el silenciador si est#, corroido pues producir un peligro de incendio y/o dafio. BUJIA Cambie su bujia cada afio para hacer que su motor arranque m#,s f_.cilmente y funcione mejor,, Ajuste la abertura de la bujfa en 0.030 pulgadao LIMPIEZA IMPORTANTE: Para obtener el mejor redimientom, mantenga lacajadelasgadorasin acumulacion de cesped y gasura. Umpie la parte de su segadora despues de cada uso. _PRECAUCl6N: Desconecte el alambre de la buj[a y p6nga!o en donde no pueda entrar en contacto con _sta. Envase °Haga descansar la segadora en su tadoo Aseg(]rese que el fUtro de aire y que el carburador queden mirando hacia ardba. Limpie la parte inferior de su segadora raspAndola pare remover la acumulaci6n de c6sped y basurao ° Limpie el motor a menudo para evitar que se acumule la basur& Un motor tapado funciona m_s caliente y se acorta su duraciSn. FILTRO DE AIRE Su motor no funcionar.5 en forma adecuada y puede sufrir dafios si se usa un filtro de aire sucio_ Cambie el filtro de aire cada afio, y m&s a menudo si siega en condiciones muy polvorosas o sucias, No lave el filtro de aire. PARA CAMBIAR EL FILTRO Manilla de la cubierta ° Mantenga las superficies pulidas y las ruedas sin gasolina, aceite, etc. • No recomendamos el uso de una manguera de jard[n para limpiar fa segadora a menos que el sistema el_ctrico, el silenciador, el filtro de aire y el carburador est_n tapados para evitar que les entre el agua. El agua en el motor puede acortar la duraci6n de _ste., LIMPIE DEBAJO DE LA CUBIERTA DE LA IMPULSION DE AIRE ° Afloje los torni!los de la cubierta. ° Empuje la cubierta hacia abajo y remuevala de la bisagra,, ° Remueva el flltro de pape! afuera del cuerpo del filtro de aire, ° Limpie la cublerta y el cuerpo del fittro de aireo • Instate un nuevo filtro de papel ° Renstale cubierta al conjunto dei fittro de aire. Asegurese que el quicio est6 montado adecuadaamente ° Empuje la cubierta hacia arriba y apriete los tornillos de la cubierta. (No los priete demaciado) Limpie debajo de la cubierta de la impulsiSn por 1o menos dos veces cada temporada. Raspe debajo de la cubierta con un cuchillo para masilla o con una herramienta parecida, para remover toda acumulaci6n de c#sped o basura en la parte inferior de la cubierta de Ia impulsiSn. 30 _PRECAUCI6N: Antes de dar cualquier sercicio o de hacer ajustes: o Sueite la barra de control y pare el motor, - Asegarese que ia cuchitla y que todas las partes movibles se hayan detenido completamenteo o Desconecte el atambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta_ PARA AJUSTAR EL MANGO El mango puede ser montado a una posici6n atta o baja. Los agujeros de montaje en el mango inferior est_n fuera del centro para levantar y bajar el mango. ° Remueva el mango superior y todas las partes atadas al mango inferior, . Remueva las clavijas de horquilla de ia clavija de montaje del puntal del mango. ° Apreite el mango inferior hacia dentro para removerio de las clavijas de montaje. ° Gire el mango inferior por encima para ievantar o bajar el mango° ° Vuelva a montar las clavijas de horquilta por encima de las clavijas de montajeo ° Vuelva a montar el mango superior y todas las partes removidas del mango inferior. SEGADORA PARA AJUSTAR LA ALTURA DE CORTE Vea "PARA AJUSTAR LA ALTURA DE CORTE" en la secci6n de Operacifn de este manual. DESVIADOR TRASERO Se proporciona un desviador trasero, adjunto entre las nJedas traseras de su segadora, para reducir a un mfnimo la posibilidad que objetos sean lanzados hacia afuera de la parte trasera de la segadora, en la posici6n en donde se encuentra el operador. Si se dafa el desviador debe cambiarseo PARA REMOVER/CAMBIAR LA CORREA DE IMPULSION Posici6n ° Remueva la cubierta de la impulsi6n. Remueva la correa empujando hacia abajo en la polea de la caja de engranajeso o Haga descansar la segadora en su lado con el filtro de aire y el carburador mirando hacia arriba, o Remueva la cuchilla. • Remueva la defensa en contra del desperdicioo ° Remueva la correa de la polea del motor en el cigue_alo o fnstale la correa nueva siguiendo los pasos anteriores en el orden inverso., • Siempre use ta correa aprobada por la f_brica para asegurarse que calce y dure. para segar "" ,.. / L; para segar f"i; ! r-"I j /-'_ il Posicidn Posici6n baja . _,. Cubierta de la Girar impulsion Correa Empujar hacia Posici6n jl-" abajo 31 alta Mango in.ferior PARA MONTAR Y ADJUNTAR EL RECOGEDOR DE CESPED o Inserta la piema del marco tubular en la abertura del recogedor de c_sped y deslice 1o entre la costura de la bolsa. AVISO; Mantenga la costura de la bolsa recogida sobre la pierna recta del marco. o Cuando el marco satga del otro lado de la costura, inserta inmediatamente el extremo del marco adentro de la bolsa como mostrado en la intercalaci6n, • Deslice la costura igual al rededor del marco tubular, al mismo tiempo trabaje el marco adentro del recogedor de c6sped. ° Monte el marco infedor al marco tubular como demostrado.. o Deslice los sugetadores de vinitio sobre el ma )a Costura soltable Marco inferior (los marcos deben estar completamente situados) marco, AVISO= Si los sujetadores de vinilio est,_n muy duros, m6talos en agua caliente. o Cierre la tapa soltabteo La tapa sottable debe estar cerrada cuando se esta operando la segadorao Marco tubular ,_kPRECAUOI6N: No haga funcionar su segadora sin el desviador de recortes o sin el recogedor de c6sped, aprobados, en su lugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando est,_ un poco abiertao Marco del bastidor MOTOR VELOCIDAD DEL MOTOR \ La velocidad del motor ha sido ajustada en la f_brica. No trate de aumentar la velocidad del motor pues se pueden producir tesiones personales_ Si cree que el motor est& funcionando demasiado r_pido o demasiado lento, lleve su segadora a un centro/ departamento de servicio autorizado para repararla o ajustarla. CARBURADOR Su carburador no es ajustable. Si su motor no est,. funcionando en forma adecuada debido a problemas que se sospecha vienen del carburador, Ileve su segadora a un centro de servicio autorizado para repararta y/o ajustarla. IMPORTANTE: Nunca manipulee el regulador del motor, el que ha sido ajustado en la fabrica para la velocidad del motor adecuada° Puede set peligroso hacer funcionar el motor a una velocidad por sobre el ajuste de alta velocidad de la fabrica, Si cree que la velocidad alta regulada del motor necesita ajuste, pongase en contacto con su centro/departmento de servicio autorizado mas cercano, el que cuenta con el equipo adecuado y la experiencia para hacer los ajustes necesarios, 32 Sujeta.dore_ vinilo _ " Inmediatamente prepare su segadora para el almacenamiento al final de cada temporada o si ta unidad no se va a usar por 30 dfas om#,& Barra de control que exige la presencia del o SEGADORA Mango Cuando se va a guardar la segadora por cierto perbdo de tiempo, Ifmpiela cuidadosamente, remueva toda la mugre, la grasa, las hojas, etco Gu_rdela en un ,_rea limpia y sec& • Umpie toda la segadora (Vea "LtMPIEZA" en la secci6n de Mantenimento de este manual). = Lubr[quela segQn se muestra en la secci6n de Mantenimento de este manual. • Asegt]rese de que todas las tuercas y clavijas y todos los pemos y tomillos est_n apretados en foma segurao Inspeccione las partes que se mueven para verificar si est_n dafiadas, quebradas o desgastada& C_.mbielas si es necesado,. ° Retoque todas las superficies que est_n oxidadas o con la pintura picada; use una lija antes de pintar. MANGO Puede doblar el mango de su segadora para almacenarla. ° Apriete los extremos inferiores deI mango inferior entre sf basra que el mango inferior quede separado del puntal def mango, luego mu_valo hacia adelante. • Suelte los pemos de montaje del mango superior Io suficiente como para permitir que el mango superior se pueda doblar hacia atr_so IMPORTANTE: Cuando doble el mango para el alacenamiento o el trasporte, asegurese que lo doble segun se muestra o puede danar los cables de control Doblarhacia adlante para almacenar Doblar hacia atras Posici6n pan segar Mango inferior MOTOR SISTEMA IMPORTANTE: Es importante evitar que se forrnen depositos de partes fundamentales del sistema de comustible tales como el carburador, el filtro del combutible, la manguera del combustible o en el estanque durante el almacenmiento,. La experiencea t&mbien endica que los combustibles mezclados con alcohol (conocido come gasohol o que tienen etanol o metanol) pueden atraer humedad, Io que conduce a ta separatiSn y a la formaciSn de _cidos durante almacemamiento,, la gasolina &cideca puede naSar el sistema de combustible de un motor durante el perido de alcamenmientoo ° Drene e! estanque de combustible° ° Haga arrancar el motor y d_jelo funcionar basra que las Ifneas del combustible y el carburador est_n vacios. ° Nunca use los productos pard limpieza del carburador o del motor en el estanque de combustible pues se pueden producir daBos permanentes. • Use combustible nuevo la prSxima temporada. AVISO: El estabilizador de combustible es una altemativa aceptable para reducir a un minimo la formaciSn de depSsitos de goma en el combustible durante el peffodo de almacenamiento. Agregue estabilizador a la gasolina en el estanque de combustible o en el envase para el almacenamientoo Siempre siga la proporci6n de mezcla que se encuentra en el envase det estabilizador, Haga funcionar el motor por Io menos 10 minutos despu6s de agregar el estabilizador, para permitir que este Ilegue al carburador,, No drene la gasolina del estanque de gasolina y el carburador si se est& usando estabilizador de combustible. ° Cuando prepare sus mangos a partir de la posiciSn de almacenamiento, el mango inferior autom,_ticamente se asegurar_, en la posici6n para segar. Mango inferior Puntal del mango Apriete para doblar DE COMBUSTIBLE CIavija de horquilfa 33 ACEITE DEL MOTOR ° Si es posible, guarde su unidad en un recinto cerrado y ct]braJa para protegeda contra el polvo y la mugre. ° Cubra su unidad con un forro protector adecuado que no retenga la humedad. No use pl&stico_ El pl_,stico no puede respirar, Io que perrnite la forrnaciSn de condensaci6n, Io que producir& la oxidaci6n de su unidad_ IMPORTANTE" Nunca cubra la segasora mientras el motor y las areas de escapetodavia estan calientes. Drene el ace_te (con el motor caliente) y c&mbielo con aceite de motor Iimpioo (Vea "MOTOR" en la ser..ciSnde Mantenimento de este manuaL) ClLINDRO o Remueva la bujfa. ,, Vacie una onza (29 ml) de aceite a trav_s del agujero de la buj[a en el cilindro. • Tire la manilla de arranque lentamente unas cuantas veces para distribuir el aceite_ • Vuelva a montar la nueva buj[a se_PRECAUCI6N: Nunca almacene la gadora con gasolina en el estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa_ Perrnita que se enfrie el motor antes de almacenarla en algun recinto cerradoo OTROS - No guarde la gasolina de una temporada a la otra_ o Cambie el envase de la gasolina si se empieza a oxidaro La oxidacidn y/o la rnugre en su gasolina producir_n problemas, DENTIFICACION DE PROBLEMAS PROBLEMA CORRECCION CAUSA .................,,,,,,,,, ,,,, No arranca 1, 2. Filtro de aire sucioo Sin combustible. 1. 2 3. Combustible 3o 4_ Agua en el combustible. 4. 5. Alambre de la bujia desconectado. Bujia mala. Cuchilla suelta o adaptador de la cuchilla quebrado. 5. 6o 7o 8. 9_ Falta de fuerza 1. 2. 3, 4,, 5o 6. rancio. Barra de control en la posiciSn suetta. Barra de control defectuosa. 6 7. Cambie la bujia, Apriete el perno de la cuchilla cambie el adaptador de la cuchillao 8 Presione la barra de control hacia el mango. 19_ Cambie la barra de control. Cuchilla desgastada, doblada 1_ o sueltao Altura de las ruedas disparejao 2o Velocidad del motor lenta. AcumutaciSn de c6sped, hojas o basura debajo de la segadora. Demasiado aceite en el motor. Velocidad de recorrido demasiado r_,pida. 34 Limpie/cambie el filtro de aireo Llene el estanque de combus tible. Drene el estanque y vuelva a llenarlo con combustible limpio y nuevo_ Drene et estanque de combus tible y el carburador y vuelva a Ilenar el estanque con gasolina nueva. Conecte el alarnbre a la bujia, i3o _4. Ajuste a fa posiciSn de "Corte m_s alto." Ajuste a la posiciSn de "Corte m_.s alto," Limpieicambie el filtro de aire, Limpie la parte infedor de la caja de la segadorao 5. Revise el nivel del aceiteo 6. Corte a una velocidad recorrido m#.s lenta. de IDENTIFICACION DE PROBLEMAS PROBLEMA H,,H,, CORRECCION CAUSA I I,.I I . Mal cortedisparejo 1_ Cuchilla desgastada, doblada 11. Cambie ta cuchilla. Apriete el o suelta. perno de la cuchillao 2o Altura de las ruedas dispareja, 2. Ajuste todas las ruedas a la misma altura, 3. AcumulaciSn de c_sped, 3 Limpie la parte inferior de la hojas o basura debajo caja de la de la segadora, segadorao Vibraci6n excesiva 1 1o 2o CuchiUa desgastada, doblada o suelta, CigueSal del motor dobladoo !. El freno del volante del 1. 2. motor est,. aplicado cuando se suetta la barra de control. CigueSal del motor doblado. 2. Cambie la cuchilla. Apriete el pemo de la cuchilla. Contacto con su centro de servicio autorizado m_s cercano. ,j,,,, Cord6n arrancador dificil de tirar 3. 4_ Adaptador de la cuchilia quebrado. La cuchilla se arrastra en 3. 4. el c_sped. P_rdida de 1. impulsi6n 2_ Recogedor de c_sped no se Ilena (si viene equipado) 1o 2. 3. Dificil de empujar 1o 2. 3, 4. Ruedas impulsoras no giran cuandoel control de impulsiSn est_ enganchado. La correa no est,. impulsando. Altura de corte demasiado baja. Levantamiento de la cuchilla desgastadoo Recogedor sin ventilaciSn de aire_ El c6sped est,, demasiado alto o la altura de la rueda demasiado baja_ Parte trasera de la caja!cuchitla de la segadora arrastr&ndose en e! c_sped. Recogedor de cSsped demasiado llenoo Posici6n de la altura del mango no adecuada para usted. 35 Presione la barra de controJ hacia el mango superior antes de tirar et cordSn arrancadoro PSngase en contacto con su centro de servicio autodzado m,_s cercano. Cambie el adaptador de la cuchilla,. Mueva la segadora a un lugar en donde el c6sped ha sido cortado o a una superficie firme para hacer arrancar el motor. 1o Ajuste o cambie el cable de ...... control deimpulsiSn, si est& roto. 2o Ponga las correas en las poleas o c&mbielas si est¢Sn rotas. 1. Eleve la altura de corte, 2. Cambie las cuchillas. 3. Limpie el recogedor 1o Eleve la altura de corte_ 2_ 3_ 4. de cSsped. Eleve la parte trasera de la caja de la segadora (1) un lugar m_.s alto. Vacfe el recogedor de c_sped Ajuste fa altura del mango de modo que le acomode. 36 ROTARY LAWN MOWER - - MODEL NO. 917.377991 GEAR CASE ASSEMBLY PART NUMBER 702511 11 14 9 KEY NO. PART NO. 17490416 2 3 4 6 137055X004 137053 57072 48373 7 8 77881 137051 DESCRIPTION KEY NO. Tapping Screw 1/4-20 x 1-1/4 Engagement Bracket Shifter Seal Gear Case Halves Kit (includes Key Nos, 4, and 7) Bearing Worm Shaft 9 10 11 12 13 14 15 16 17 18 19 PART NO. Drive Shaft HardenedWasher Clutch Yoke Bushing Plug Helical Gear Clutch Jaw Grease E-Ring Hi-Pro Key Spring Bracket 137074 57079 13! 484 700343 86447 137050 750436X 750369 12000003 850848 81585X004 NOTE: All component dimensions in U.S, inches. +1inch = 25.4 mm 37 DESCRIPTION given t_ t_ O_ n., LU m -J LU 0 LU 0 / ..I 0 n., •tT_ 00 ,. ¸ ",-"CO E = "_'_ ' _ _o × o 5_ o_ t'== N z 0 IO_ 0") Z v .,__ _ o (.,9u. 03 _ 0 .__ .1,.,. W m r_ m I-_Z Z ,-I u,I 0 Cq "_ o_ ._N0-o 0 t_ ILl a r,,: _o,._o _d ILl 0 X Z o od x --1 >,,, z 0 m I- I,,,- 0 rt- 0 u,,I nZ o ,,,d 39 N _J g: E E Z _o 0"_ O_ I,,. m _u. -o t_ !,,1,1 oI_N_mz_N,r_o_ TO') W I..rt' . ,<0 Z ,.J I.LI o-Z "_ 0,_ D',,- "_ "J t'_ ! "_ "- '- 0 !11 0 OJ X O4 ai Z 6 X m= ¢0 -I 0 m >,., >,. E o _ × E _ reiLl o 03= 00 Iz) _d 41 03 CRAFTSMAN 4-CYCLE ENGINE MODEL NO. 143.996704 _103 194 gB 199 370A I r I 370R / 292 261% {_,,..,,310 "26O _3o7 ff_305 J)" ,1261 1_ _t308 4t7 9O0 416 _51A 12 24O 187A 350 \ 177 251A 75 42 CRAFTSMAN KEY NO. PART NO, I 36177 2 6 9 10 I1 t2 12C 14 15 16 17 !8 27652 36059 590568 36002 36003A 32447 36005A 28277 36006 36008 31335 651018 19 20 25 36103 36010 37149 26 30 4O 650802 36185 40004 40005 36070 41 36071 42 43 45 40006 40007 20381 36023A 46 48 50 52 69 70 32610A 36030 36031A 29914 36032A 37271 75 8O 81 82 83 85 86 89 90 91 92 93 100 '101 103 36010 30574A 30590A 30591 36057 36034 650924 611154 611155 611156 650815 650816 34443B 610118 651007 110 t19 120 125 36054 36061 36187 36471 126 130 135 150 151 151A 36472 29314C 29315C 6021A 35395 31672 31673 40016A 4-CYCLE ENGINE DESCRIPTION Cylinder (tncl. 2,10,12,20 & 125) DowetPin BreatherElement Screw, 10-24 x 3/4" Breather Valve Body Check Valve BreatherTube Breather Cover & Gasket FtatWasher GovernorRod (Machined) Governor Lever GovernorLeverClamp Screw, Torx T-15, 8-32 x 19/64" Governor Spring Oil Seal Blower Housing Baffle Ass'y,(IncH95) Screw, 1/4-20 x 5/8" Crankshaft Piston,Pin,Ring Set (Std.) Piston,Pin, Ring Set (.0t00S) Piston & Pin Ass'y.(Std) (Incf. 43) Piston & Pin Ass'y.. (.010 OS)(Incl.43) Ring Set (Std.) Ring Set (o010 OS) Piston Pin Retaining Ring Connecting Rod Ass'yo (tncl. 46) Connecting Rod Bolt Valve Lifter Camshaft(MCR) Oil Pump Ass'y. Mounting Flange Gasket Mounting Flange (IncL 72 thru 85) Oil Seal Governor Shaft Washer Governor Gear Ass'yo(Inc181) GovernorSpool Idler Gear Screw, 1/4-20 x i-9/!6" Flywheel Key Rywheel FlywheelFan BelrevilleWasher Flywheel Nut Solid State Ignition Spark Plug Cover Screw, Torx T-15, 10-24 x 15/t6" GroundWire Cylinder Head Gasket Cylinder Head Exhaust Valve (Std) (IncL 151) Exhaust Valve (1/32" OS) Intake Valve (Std.) (Incl.. 15t) Intake Valve (1/32" OS) Screw, 5/164 8 x 1-i/2" Resistor Spark Plug (RJ 19LM) Valve Spring Lower Valve Spring Cap Intake Valve Seal MODEL NO, 143o996704 KEY NO. PART NO. 169 172 174 177 184 186 187A 190 19tA 192 193 194 195 198 199 239 27234A 32755 30200 650925A 36163 36009 37148 36013 36012 36016 36015 36014 610973 36017 360t8 36048 240 243B 245 250 251 251A 255 256 260 261 263A 275 276 277 285 287 290 292 300 30t 305 307 308 310 346A 347 350 370A 370C 370R 380 390 400 36190 651041 36046 36!91 650928 650933 36193 650983 36188 650737 36192 36107A 36043 650927 34449A 650926 29774 26460 36189 36246 36063 35499 36040 36064 28763 650898A 36045A 36261 37318 37317 640020A 590739 36062D 416 36085 417 900 650821 ---- 900 DESCRIPTION * * Valve Spring Box Gasket Valve Spring Box Cover Screw, 10-24 x 9/16" Carburetor Mounting Stud Carburetor Gasket Governor Link Air Baffle Brake Lever Ass'y. Brake Control Lever Brake Control Lever Link Brake Spring Retaining Ring Terminal Ass'y. Brake Control Lever Spring Brake Lever Bushing CarburetorTo Air Cleaner Gasket Air Cleaner Body (Incl. 239 & 350) Air Cleaner Stud Air Cleaner Filter Air Cleaner Cover Lock Nut 1/4-20 Wing Nut, 1/4-20 Control Rate Screw, 8-32 x t7/32" BlowerHousing Screw, 1/4-20 x 1t2" Starter Grill Muffler Locking Plate Screw, 5/t6-18 x 2-11/32" Starter Cup Screw, 8-32 x 21/64" Fuel Line Fuel Line Clamp Fuel Tank (lncL 301) Fuel Cap Oil FilITube "O" Ring FiIITube Clip Dipstick Screw, 10-32 x 35/64'_ Screw, 10-32 x 27/64" Primer Lubrication Decal PrimerDecal Warning Decal Carburetor (IncL 184 & 239) Rewind Starter Gasket Set (IncL Items Marked *) Spark Arrestor Kit (Incl, 417)(Optional) Screw, 10-32 x t/2" (Optional) ReplacementEngine 750819B, order from 71-999 Replacement Short Block 750797B, RPM High 2900 to 3200 This engine could 590702 starter° NOTE: have been NOTE; All component dimensions U.S, inches 1 inch = 25.4 mm 43 built with given in CRAFTSMAN 4-CYCLE ENGINE MODEL NO. 143.996704 14A I 4r 27 I "_3g 44 CRAFTSMAN 4-CYCLE KEY NO. _ 1 5 6 7 14A 25 27 28 29 30 32 3.3 36 37 37A 38 38A 39 40 47 ENGINE PART NO. 640020A 6.32539 632593 632541 650506 632773 632675A 632544 632543 632548 632709 632672 632673 640022 63254.7 632547 632545 632545 632549 640021 632554 MODEL NO. 143.996704 DESCRIPTION Carburetor (IncL t87B & 239 of Engine Parts List) Throttle Shaft & Lever Assembly Dust Seal Throttle Shutter Throttle Shutter Screw Ventud Float Bowl Float Shaft Float Float Bowl to Body Gasket Inlet Needle & Seat Bowl Drain Screw Bowl Drain Washer Main NozzleTube "O" Ring "O" Ring, Main Nozzle Tube Spring, Main Nozzle Tube Spring Float Bow! Retainer Main Fue! Jet Welch Plug, Idle Mixing Well 45 CRAFTSMAN 4-CYCLE ENGINE MODEL NO. 143.996704 13 _8 _3 KEY NO. PART NO. 1 2 3 4 5 6 7 8 11 590702 590599A 590600 59O696 590601 590697 590698 590699 590700 590703 12 13 590535 5907O1 DESCRIPTION Recoil Starter Spring Pin (Incl. 4) Washer Retainer Washer Brake Spring Starter Dog Dog Spring Pulley & Rewind Spring Ass'y. Starter Housing Ass'y. (40 degree grommet) Starter Rope ( 98" X 9/64" dial) Starter Handle 46 CRAFTSMAN 4-CYCLE ENGINE MODEL NO. 143.996704 "_,. _8 KEY NO. PART NO, -3 6 7 8 590739 590740 5906t6 590617 590618A tl 59063B 12 590535 13 14 590701 590760 DESCRIPTION Rewind Starter Retainer Starter Dog Dog Spring Pulley & Rewind Spring Ass'y Starter Housing Ass'y (40 degree grommet) Starter Rope (Length 98" x 9/64" dia,) Starter Handle Spring Clip 47 | | For in-home major brand repair service: Call 24 hours a day, 7 days a week I=800=4=MY-HONIE _" (1-800-469-4663) Para pedir servicio de reparacibn 1-800-676-5811 a domicilio in Canada for all your service and parts needs call Au Canada pour tout le service ou les pi6ces 1-800-665-4455 For the repair or replacement parts you need: Call 6 am - 11 pm CST, 7 days a week PartsDirect 1-800-366-PART (_-800-366-7278) Para ordenar piezas con entrega a domicilio 1-800-659-7084 For the location of a Sears Parts and Repair Center in your area: Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement: Call 9 am - 5 pro, Monday- Saturday 1-800-827-6655 Home Central 'M 171071 10.28.99 VB Printed in U.S.A.
This document in other languages
- español: Craftsman 917.377991