Download Yamaha R-V901 Service manual

AV RECEIVER
RX-V800/RX-V800RDS/HTR-5280
SERVICE MANUAL
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING:
Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
■ CONTENTS
TO SERVICE PERSONNEL .......................................... 1
IMPEDANCE SELECTOR ............................................. 1
SPECIFICATIONS .......................................................... 2
REMOTE CONTROL TRANSMITTER .......................... 3
FRONT PANELS ............................................................ 4
REAR PANELS .......................................................... 5~6
INTERNAL VIEW ........................................................... 7
DISASSEMBLY PROCEDURES ................................... 8
SELF DIAGNOSIS FUNCTION (DIAG) ................... 9~23
AMP ADJUSTMENT .................................................... 23
DISPLAY DATA ........................................................... 24
IC DATA ................................................................. 25~31
BLOCK DIAGRAM ................................................. 32~35
PRINTED CIRCUIT BOARD .................................. 36~59
PIN CONNECTION DIAGRAM .............................. 60~61
SCHEMATIC DIAGRAM ........................................ 62~68
PARTS LIST ........................................................... 69~87
REMOTE CONTROL TRANSMITTER .................. 88~89
100727
P.O.Box 1, Hamamatsu, Japan
RX-V800/RX-V800RDS/HTR-5280
WARNING:
RX-V800/RX-V800RDS/HTR-5280
■ TO SERVICE PERSONNEL
1. Critical Components Information
Components having special characteristics are marked s
and must be replaced with parts having specifications equal
to those originally installed.
WALL
OUTLET
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated
from supply circuits.
●
Meter impedance should be equivalent to 1500 ohm shunted
by 0.15µF.
●
Leakage current must not exceed 0.5mA.
●
Be sure to test for leakage with the AC plug in both polarities.
EQUIPMENT
UNDER TEST
AC LEAKAGE
TESTER OR
EQUIVALENT
INSULATING
TABLE
WARNING: CHEMICAL CONTENT NOTICE!
The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and /or plastic
(where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency
(and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
■ IMPEDANCE SELECTOR
WARNING
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
ATTENTION
RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR.
AC OUTLETS
THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATIONIS SUBJECT TO
THE CONDITION THAT THIS DEVICE DOES
NOT CAUSE HARMFUL INTERFERENCE.
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
US
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
IMPEDANCE SELECTOR
WARNING:
Do not change the IMPEDANCE SELECTOR
switch setting while the power to this unit is
on, otherwise this unit may be damaged.
1
RX-V800/RX-V800RDS/HTR-5280
■ SPECIFICATIONS
■ Audio Section
Minimum RMS Output Power (Power Amp. Section)
(20 Hz to 20 kHz, 0.04% THD, 8 ohms)
MAIN ....................................................................... 100W + 100W
CENTER ............................................................................... 100W
REAR ...................................................................... 100W + 100W
Maximum Power (EIAJ)
(1 kHz, 10% THD, 8 ohms)
MAIN ....................................................................... 140W + 140W
CENTER ............................................................................... 140W
REAR ...................................................................... 140W + 140W
Dynamic Power Per Channel (IHF)
MAIN L/R (8/6/4/2 ohms)
[U model] ........................................................ 135/170/205/245 W
[C, A, B, G, L, R, T models] ........................... 125/160/195/230 W
DIN Standard Output Power Per Channel
(1 kHz, 0.7% THD, 4 ohms)
[G model] ............................................................................. 140 W
Dynamic Headroom
8 ohms
[U model] ............................................................................. 1.3 dB
[C model] ............................................................................. 1.0 dB
IEC Power
MAIN L/R (1 kHz, 0.04% THD, 8 ohms)
[G model] ................................................................. 105W + 105W
Damping Factor
MAIN L/R (20 Hz to 20 kHz, 8 ohms) .......................... 80 or more
Input Sensitivity / Input Impedance
PHONO MM ................................................... 2.5 mV / 47 k-ohms
CD, etc. ......................................................... 150 mV / 47 k-ohms
Maximum Input Signal Level
PHONO MM (1 kHz, 0.1% THD) ...................................... 100 mV
CD, etc. (1 kHz, 0.5% THD, Effect On) ................................ 2.2 V
Output Level / Output Impedance
REC OUT ..................................................... 150 mV / 0.9 k-ohms
PRE OUT ....................................................... 2.57 V / 1.2 k-ohms
SUB WOOFER [MAIN SP: Small] ...................... 4 V/1.2 k-ohms
Headphone Jack Rated Output / Impedance
1 kHz, 40 mV, 8 ohms ..................................... 0.15 V / 100 ohms
Frequency Response
Power Amp only (5 Hz to 100 kHz) ................................... 0/-3 dB
CD, etc. to MAIN SP OUT (10 Hz to 100 kHz) .................. 0/-3 dB
RIAA Equalization Deviation
PHONO MM (20 Hz to 20 kHz) .................................... 0 ± 0.5 dB
Total Harmonic Distortion
(20 Hz to 20 kHz)
PHONO MM, to REC OUT (1V) .............................. 0.02% or less
CD, etc. to MAIN SP OUT (50 W / 8 ohms) ............ 0.04% or less
Signal to Noise Ratio (IHF-A network)
CD, etc. to MAIN SP OUT (Input shorted, Effect Off)
150 mV .................................................................... 96 dB or more
200 mV .................................................................... 98 dB or more
Residual Noise (IHF-A netwok)
MAIN L/R SP OUT ................................................. 150 µV or less
Channnel Separation
(Vol -30 dB, Effect Off)
PHONO (Input Shorted, 1 kHz) .............................. 60 dB or more
PHONO (Input Shorted, 10 kHz) ............................ 55 dB or more
CD, etc. (Input 5.1 k-ohms terminated, 1 kHz) ............. 60 dB or more
CD, etc. (Input 5.1 k-ohms terminated, 10 kHz) ........... 45 dB or more
Tone Control Characteristics
Bass: Boost/Cut ................................................ ±10 dB (50 Hz)
Turnover Frequency ............................................ 350 Hz
Treble: Boost/Cut .............................................. ±10 dB (20 kHz)
Turnover Frequency ........................................... 3.5 kHz
Filter Characteristics
MAIN, Rear SP Small (H.P.F.) .......................... 90 Hz, 12 dB/oct.
SUBWOOFER (L.P.F.) ...................................... 90 Hz, 18 dB/oct.
Bass Extension
60 Hz ...................................................................................... 6 dB
■ Video Section
Video Signal Type
[U, C, R, T models] .............................................................. NTSC
[A, B, G, L, models] ................................................................. PAL
Video Sigal Level
............................................................................ 1 Vp-p / 75 ohms
S-Video Sigal Level
Y ......................................................................... 1 Vp-p / 75 ohms
C .................................................................. 0.286 Vp-p / 75 ohms
Component Video Sigal Level
Y ......................................................................... 1 Vp-p / 75 ohms
Cb / Cr ............................................................. 0.7 Vp-p / 75 ohms
Maximum Input Level
.......................................................................................... 1.5 Vp-p
Sigal to Noise Ratio
................................................................................. 50 dB or more
Monitor Out Frequency Response
S-Video Signal Level ................................. 5 Hz to 10 MHz, -3 dB
Component Signal Level .............................. DC to 30 MHz, -3 dB
■ FM Section
Tuning Range
[U, C models] ................................................... 87.5 to 107.9 MHz
[R, T, A, B, G, L models] .................................. 87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF)
(100% Mod)
Mono .................................................................. 2.0 µV (17.3 dBf)
Stereo .................................................................. 25 µV (39.2 dBf)
Usable Sensitivity (IHF)
Mono .................................................................. 1.0 µV (11.2 dBf)
Selectivity
at 400 kHz ............................................................................ 70 dB
Signal to Noise Ratio (IHF)
Mono / Stereo .......................................................... 76 dB / 70 dB
Harmonic Distortion
(1 kHz)
Mono/Stereo ................................................................. 0.2 / 0.3 %
Stereo Separation
1 kHz .................................................................................... 45 dB
Frequency Response
20 Hz to 15 kHz .......................................................... +0.5 / -2 dB
Antenna Input
...................................................................... 75 ohms unbalanced
■ AM Section
Tuning Range
[U, C, R, T models] ............................................ 530 to 1,710 kHz
[A, B, G, L models] ............................................. 531 to 1,611 kHz
Usable Sensitivity
........................................................................................ 300 µV/m
Antenna
................................................................................. Loop Antenna
■ General
Power Supply
[U, C models] ...................................................... AC 120 V, 60 Hz
[R models] ................................ AC 110/120/220/240 V, 50/60 Hz
[T model] ............................................................. AC 220 V, 50 Hz
[A model ] ............................................................ AC 240 V, 50 Hz
[B, G, L models] .................................................. AC 230 V, 50 Hz
Power Consumption
[U model] ............................................................................. 260 W
[C model] .............................................................. 300 W / 360 VA
[R, T, A, B, G, L models] ..................................................... 300 W
Maximum Power Consumption
(5ch Drive, 10% THD)
[R model] ............................................................................. 585 W
AC Outlets
2 switched outlets
[U, C, R, T G, L models] .................................... 100W max., total
1 switched outlets
[A, B models] ............................................................... 100W max.
Dimensions (W x H x D)
............................. 435 x 171 x 431.5 mm (17-1/8" x 6-3/4" x 17")
Weight
.................................................................... 15.0 kg (33 lbs. 1 oz.)
Accessories
Remote control transmitter, Manganese batteries, Indoor FM
antenna, AM loop antenna
* Specifications are subject to change without notice.
U ..........
A ..........
G ..........
R ..........
U.S.A. model
Australian model
European model
General model
C ...... Canadian model
B ...... British model
L ....... Singapore model
T ....... China model
2
RX-V800/RX-V800RDS/HTR-5280
• DIMENSIONS
21.5
(7/8")
■ REMOTE CONTROL
TRANSMITTER
DSP/TUN
Unit : mm (inch)
171 (6-3/4")
21
(13/16")
150 (5-7/8")
16
(5/8")
HALL
CD
435 (17-1/8")
INPUT
431.5 (17")
394 (15-1/2")
DSP
CHURCH
TUNER
JAZZ
MD/TAPE
1
2
3
ROCK
DVD
ENTERTAINMENT
D-TV/LD
TV SPORTS
VCR 1
4
5
6
MONO MOVIE
CD-R
1-MOVIE THTR-2
CBL/SAT VCR 2/DVR
7
8
9
y y/DTS SUR.
PHONO
6.1/ES
6CH INPUT
EFFECT
V-AUX
ENTER
>10
0
INDEX
CH
CH
DISC SKIP
PRESET
VCR REC
DISPLAY
/
A/B
TEST
A/B/C/D/E
ES
COD ET
DIR A
SELECT
ON
TITLE
LEVEL
DIR B
SCREEN
MENU
POWER
SET MENU
AV
POWER
STANDBY
POWER
I
TV
INPUT
TV
TV VOL
SLEEP
MUTE
3
VOLUME
RX-V800/RX-V800RDS/HTR-5280
■ FRONT PANELS
• U, C and A models → BL (Black model)
• L model → GD (Gold model)
• R and T models → BL (Black model) and GD (Gold model)
RX-V800 (U, C, A, L, R, T models)
INPUT
VOLUME
INPUT MODE
VIRTUAL
DIGITAL
PRO LOGIC
DSP
STANBY
/ON
6.1/ES
PCM
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
B
BASS
EXTENSION
PROCESSOR
DIRECT
VOLUME
ZONE 2
SLEEP
SP
AB
A/B/C/D/E
SPEAKERS
A
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
PRESET/
TUNING
PRESET
/TUNING
FM/AM
TUNING
MODE
BASS
TREBLE
MAN'L/AUTO FM AUTO/MAN'L MONO
EDIT
EFFECT
OFF
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
TUNER
PHONES
ON
MEMORY
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
6CH INPUT
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
PROGRAM
DSP
VIDEO AUX
SILENT
• B model → BL (Black model)
• G model → BL (Black model), GD (Gold model) and TI (Titan model)
RX-V800RDS (B, G models)
INPUT
VOLUME
INPUT MODE
VIRTUAL
DIGITAL
PRO LOGIC
DSP
STANBY
/ON
6.1/ES
PCM
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
B
BASS
EXTENSION
PROCESSOR
DIRECT
VOLUME
ZONE 2
SLEEP
SP
AB
A/B/C/D/E
SPEAKERS
A
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
PRESET/
TUNING
PRESET
/TUNING
FM/AM
RDS MODE
/FREQ
EON
PTY SEEK
MAN'L/AUTO FM AUTO/MAN'L MONO
EDIT
EFFECT
OFF
TUNING
MODE
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
BASS
TREBLE
TUNER
PHONES
ON
MEMORY
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
6CH INPUT
S VIDEO
MODE
VIDEO
L
AUDIO
R
START
OPTICAL
PROGRAM
DSP
VIDEO AUX
SILENT
• U, C and A models → BL (Black model)
• T model → GD (Gold model)
HTR-5280 (U, C, A, T models)
INPUT
VOLUME
INPUT MODE
VIRTUAL
DIGITAL
PRO LOGIC
DSP
STANBY
/ON
6.1/ES
PCM
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
A/B/C/D/E
SPEAKERS
A
B
BASS
EXTENSION
PROCESSOR
DIRECT
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
PRESET/
TUNING
PRESET
/TUNING
FM/AM
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
TUNING
MODE
BASS
TREBLE
MAN'L/AUTO FM AUTO/MAN'L MONO
EDIT
PHONES
OFF
MEMORY
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
TUNER
EFFECT
ON
VOLUME
ZONE 2
SLEEP
SP
AB
6CH INPUT
S VIDEO
VIDEO
L
AUDIO
R
OPTICAL
PROGRAM
DSP
SILENT
VIDEO AUX
4
RX-V800/RX-V800RDS/HTR-5280
■ REAR PANELS
U model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
A
Y
ATTENTION
RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR.
OUT
(REC)
4
CD
3
3
IN
(PLAY)
75
4
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
FM
ANT
B
IN
(REC)
Y
VDR 1
1
GND
PB/
CB
OUT
CD
D-TV
/LD
CBL
/SAT
A
PHONO
MAIN
MAIN
IN
z
z
SUB
WOOFER
CLASS 2 WIRING
z
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION
SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
SURROUND
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
US
B
MONITOR
OUT
OUT
AC OUTLETS
THIS DEVICE COMPLIES WITH PART 15 OF
THE FCC RULES. OPERATIONIS SUBJECT TO
THE CONDITION THAT THIS DEVICE DOES
NOT CAUSE HARMFUL INTERFERENCE.
MAIN
PR/
CR
IN
VDR 2
/DVR
7
8
OUTPUT
z
z
CENTER
6
OPTICAL
COAXIAL
CD
SPEAKERS
4
DVD
5
WARNING
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
COMPONENT
DVD
MD/TAPE
2
OPTICAL GND
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
z
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
OUT
PR/
CR
MONITOR
OUT
CENTER
DIGITAL INPUT
REMOTE CONTROL
SUB
WOOFER
S VIDEO
REAR (SURROUND)
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
VIDEO
6CH INPUT
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
C model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
A
Y
ATTENTION
RISQUE DE CHOC
ELECTRIQUE NE PAS OUVRIR.
OUT
(REC)
4
CD
3
3
IN
(PLAY)
75
4
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
FM
ANT
B
IN
(REC)
Y
VDR 1
1
GND
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
6
PHONO
VDR 2
/DVR
COAXIAL
CD
A
7
8
AC OUTLETS
OUTPUT
SWITCHED
I20V 60Hz
I00W MAX. TOTAL
0.8A MAX TOTAL
MAIN
z
z
MAIN
B
z
CENTER
OPTICAL
CBL
/SAT
SPEAKERS
4
DVD
5
WARNING
TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
COMPONENT
DVD
MD/TAPE
2
OPTICAL GND
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
MAIN
IN
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPEDANCE SELECTOR
SET BEFORE POWER ON
SELECTEUR D'IMPEDANCE
CENTER
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
SURROUND
z
MONITOR
OUT
OUT
z
CLASS 2 WIRING
z
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
OUT
PR/
CR
MONITOR
OUT
CENTER
DIGITAL INPUT
REMOTE CONTROL
SUB
WOOFER
S VIDEO
REAR (SURROUND)
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
VIDEO
6CH INPUT
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
A model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
OUT
(REC)
4
OPTICAL GND
CD
A
Y
IN
(PLAY)
75
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
FM
ANT
B
IN
(REC)
Y
VDR 1
1
GND
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
6
PHONO
VDR 2
/DVR
COAXIAL
CD
7
8
OUTPUT
MAIN
B
z
MAIN
IN
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
OUT
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
SURROUND
z
MONITOR
OUT
z
CLASS 2 WIRING
z
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
I00KHZ/10KHZ
OUT
PR/
CR
MONITOR
OUT
REAR (SURROUND)
50KHZ/9KHZ
CENTER
DIGITAL INPUT
AC OUTLET
MAIN
z
z
CENTER
OPTICAL
CBL
/SAT
A
4
DVD
5
SPEAKERS
SWITCHED
I00W MAX.
3
3
4
COMPONENT
DVD
MD/TAPE
2
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
REMOTE CONTROL
SUB
WOOFER
6CH INPUT
FM
S VIDEO
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
AM
FREQUENCY
STEP
VIDEO
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
B model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
(REC)
4
OPTICAL GND
CD
A
IN
(PLAY)
75
FM
ANT
Y
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
B
IN
(REC)
Y
VDR 1
GND
A
1
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
PHONO
OPTICAL
VDR 2
/DVR
COAXIAL
CD
7
MAIN
CBL
/SAT
8
SURROUND
B
z
MONITOR
OUT
z
PR/
CR
MONITOR
OUT
5
SUB
WOOFER
6CH INPUT
S VIDEO
CENTER
VIDEO
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
IMPEDANCE SELECTOR
SET BEFORE POWER ON
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
CENTER
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
OUT
z
CLASS 2 WIRING
z
DIGITAL INPUT
MAIN
MAIN
CENTER
6
AC OUTLET
OUTPUT
z
z
4
DVD
5
SPEAKERS
SWITCHED
I00W MAX.
3
3
4
COMPONENT
DVD
MD/TAPE
OUT
2
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
REAR (SURROUND)
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
RX-V800/RX-V800RDS/HTR-5280
G model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
OUT
(REC)
4
OPTICAL GND
CD
A
Y
IN
(PLAY)
75
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
FM
ANT
B
IN
(REC)
Y
VDR 1
1
GND
PB/
CB
OUT
CD
D-TV
/LD
6
PHONO
AC OUTLETS
MAIN
MAIN
B
z
VDR 2
/DVR
7
MAIN
8
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION
SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
OUT
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
z
PR/
CR
MONITOR
OUT
CENTER
DIGITAL INPUT
SUB
WOOFER
S VIDEO
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
PB/
CB
ZONE 2 OUT
SURROUND
z
MONITOR
OUT
z
CLASS 2 WIRING
PR/
CR
IN
OPTICAL
CD
OUTPUT
z
z
CENTER
COAXIAL
CBL
/SAT
A
4
DVD
5
SPEAKERS
SWITCHED
I00W MAX. TOTAL
3
3
4
COMPONENT
DVD
MD/TAPE
2
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
REAR (SURROUND)
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
VIDEO
6CH INPUT
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
L model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
OUT
(REC)
4
OPTICAL GND
CD
A
Y
IN
(PLAY)
75
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
FM
ANT
B
IN
(REC)
Y
VDR 1
1
GND
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
6
PHONO
VDR 2
/DVR
COAXIAL
CD
7
8
OUTPUT
MAIN
B
z
MAIN
IN
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
Y
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
SURROUND
z
MONITOR
OUT
OUT
z
CLASS 2 WIRING
z
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
I00KHZ/10KHZ
OUT
PR/
CR
MONITOR
OUT
REAR (SURROUND)
50KHZ/9KHZ
CENTER
DIGITAL INPUT
AC OUTLETS
MAIN
z
z
CENTER
OPTICAL
CBL
/SAT
A
4
DVD
5
SPEAKERS
SWITCHED
I00W MAX. TOTAL
3
3
4
COMPONENT
DVD
MD/TAPE
2
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
REMOTE CONTROL
SUB
WOOFER
6CH INPUT
FM
S VIDEO
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
AM
FREQUENCY
STEP
VIDEO
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
R, T model
AUDIO
DIGITAL OUTPUT
AUDIO
VIDEO
TUNER
MD/
TAPE
IN
COMPONENT
DVD
A
OUT
2
(REC)
4
OPTICAL GND
3
3
IN
(PLAY)
75
4
FM
ANT
5
GND
D-TV
/LD
PB/
CB
CBL
/SAT
PR/
CR
UNBAL. CD-R
D-TV/LD
OUT
B
IN
(REC)
Y
VDR 1
1
CD
OUT
PB/
CB
IN
PR/
CR
D-TV
/LD
6
PHONO
VDR 2
/DVR
COAXIAL
7
8
MAIN
IN
MONITOR
OUT
B
z
SWITCHED
I00W MAX. TOTAL
z
SUB
WOOFER
ATTENTION POUR UN REGLAGE
CORRECT, SE REPORTER AU MANUEL
D'INSTRUCTIONS.
CAUTION SEE INSTRUCTION
MANUAL FOR CORRECT SETTING.
IMPEDANCE SELECTOR
SET BEFORE POWER ON
CENTER
MAIN A OR B 4 MIN. SPEAKER
A B 8 MIN. SPEAKER
CENTER
6 MIN. SPEAKER
6 MIN. SPEAKER
REAR
PB/
CB
ZONE 2 OUT
SURROUND
z
CLASS 2 WIRING
Y
OUT
MAIN A OR B 8 MIN. SPEAKER
A B I6 MIN. SPEAKER
8 MIN. SPEAKER
8 MIN. SPEAKER
CENTER
REAR
z
I00KHZ/10KHZ
OUT
PR/
CR
MONITOR
OUT
50KHZ/9KHZ
CENTER
REMOTE CONTROL
AC OUTLETS
MAIN
MAIN
z
DIGITAL INPUT
OUTPUT
z
z
CENTER
OPTICAL
CBL
/SAT
SPEAKERS
A
4
DVD
CD
VOLTAGE SELECTOR
Y
MD/TAPE
CD
CD-R
VIDEO
DVD
(PLAY)
AM
ANT
CD-R
S VIDEO
3
1
SUB
WOOFER
6CH INPUT
FM
AM
FREQUENCY
STEP
S VIDEO
VIDEO
REAR (SURROUND)
REAR (SURROUND)
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES.
ARE
"DOLBY "," AC-3 "," PRO LOGIC ", AND THE DOUBLE-D SYMBOL
TRADEMARKS OF DOLBY LABORATORIES. CONFIDENTIAL UNPUBLISHED
WORKS. C I992-I997 DOLBY LABORATORIES. ALL RIGHTS RESERVED.
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC. US PAT.
NO.5,45I,942 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS",
"DTS DIGITAL SURROUND", ARE TRADEMARKS OF DIGITALTHEATER SYSTEMS, INC.
COPYRIGHT 1998 DIGITAL THEATER SYATEMS, INC, ALL RIGHTS RESERVED.
6
RX-V800/RX-V800RDS/HTR-5280
■ INTERNAL VIEW
1
2
3
4 5
678 9
0
L
A
B
K
J
I
HG
1 POWER (3) P.C.B.
2 MAIN (5) P.C.B.
3 MAIN (2) P.C.B.
4 VIDEO (3) P.C.B.
5 VIDEO (2) P.C.B.
6 VIDEO (1) P.C.B.
7 POWER (7) P.C.B.
8 POWER (8) P.C.B.
9 POWER (9) P.C.B.
0 POWER (10) P.C.B.
7
F
E
D
A DSP P.C.B.
B FUNCTION P.C.B.
C OPERATION (5) P.C.B.
D OPERATION (4) P.C.B.
E MAIN (1) P.C.B.
F POWER (6) P.C.B.
G POWER (5) P.C.B.
H POWER (4) P.C.B.
I POWER (2) P.C.B.
J MAIN (4) P.C.B.
C
K MAIN (3) P.C.B.
L POWER (1) P.C.B.
RX-V800/RX-V800RDS/HTR-5280
■ DISASSEMBLY PROCEDURES
1
(Remove parts in the order as numbered.)
Disconnect the power cord from the AC outlet.
1. Removal of Top Cover
a. Remove 2 screws (1), 4 screws (2) and 5 screws (3)
in Fig. 1.
b. Slide the Top Cover rearward to remove it.
3 3
3
2
2. Removal of Front Panel
Remove 9 screws (4) in Fig. 1, and the Front Panel
can be removed forward.
3. Removal of MAIN PCB (1)
a. Remove the Top Cover.
b. Remove 2 screws (5) in Fig. 3 AND remove the
support metal plate.
c. Disconnect 3 connectors (CB232, CB601, CB602 in
Fig.2) from the VIDEO PCB (1), and disconnect the
connector (CB3) from the MAIN PCB (1) in Fig. 2.
d. Remove 8 screws (6) in Fig. 3, and the VIDEO PCB (1)
and VIDEO PCB (3) can be removed.
e. Disconnect the connector (CB353) from the POWER
PCB (6) in Fig. 2.
f. Remove the plastic rivet 7, and the POWER PCB (6)
can be removed upward from the heat sink.
g. Disconnect the connector (CB1 in Fig. 2) from the MAIN
PCB (1) .
h. Remove 2 screws (8) in Fig. 2, and the support
Transistor can be removed.
i. Remove 6 screws (9) in Fig. 2.
j. Remove 6 screws (0) in Fig. 3.
k. Pull out the MAIN PCB (1) forward as shown in Fig. 3.
At this time, disconnect the flexible flat cable connected
to the MAIN PCB (1) if necessary.
4
2
4
Fig. 1
9
9
CB601
5
5
CB602
CB3
8
CB232
CB1
CB353
0
0 0
6
Fig. 3
6
9 7 9
9
VIDEO (1) PCB
POWER (6) PCB
MAIN (1) PCB
Fig. 2
8
RX-V800/RX-V800RDS/HTR-5280
■ SELF DIAGNOSIS FUNCTION (DIAG)
There are 13 DIAG menu items each of which has sub-menu items. Listed in the table below are menu items and sub-menu
items.
No. DIAG menu
1 DSP THROUGH
2
HP ROUTE
3
RAM THROUGH
4
5
PRO LOGIC
SPEAKERS SET
6
DISPLAY CHECK
7
MANUAL TEST
8
RS-232C
9
PRESET
10 AD DATA CHECK
11 IF STATUS
12 DSP RAM CHECK
13 VERSION/CHECK SUM/PORT
9
sub-menu
1. ANALOG BYPAS (ANALOG BYPASS)
2. DSP 0dB
3. DSP FULL BIT
1. HP 0dB
2. HP FULL BIT
1. RAM 0dB
2. MAIN ATT
1. YSS928
1. MAIN:SML 0dB (MAIN:SMALL 0dB)
2. MAIN:LRG -10dB (MAIN:LARGE -10dB)
3. CENTER:NONE
4. LFE/B:MAIN (LFE/BASS:MAIN)
5. Front Mix:5ch
1. VFD CHECK (initial screen)
2. VFD DISP OFF (All segments OFF)
3. VFD DISP ALL (All segments ON 100%)
4. VFD DIMMER (All segments ON 50%)
5. CHECKED PATTERN (ON in lattice)
1. ALL
2. MAIN L
3. CENTER
4. MAIN R
5. REAR R
6. REAR L
7. LFE
1. TxRx DATA (unused)
2. HARD FLOW (unused)
1. PRESET INHIBIT (memory initialization inhibited)
2. PRESET RESERVED (memory initialized)
1. REC-OUT (unused)
2. K0/K1 (panel key)
3. DC/PS (protection)
1. IST (internal status)
2. CS1 (channel status 1)
3. CS2 (channel status 2)
4. CS3 (channel status 3)
5. CS4 (channel status 4)
6. CS5 (channel status 5)
7. BI1 (BSI-DD 1)
8. BI2 (BSI-DD 2)
9. BI3 (BSI-DD 3)
10. BI4 (BSI-DD 4)
11. BS1 (BSI-DTS 1)
12. BS2 (BSI-DTS 2)
13. BS3 (BSI-DTS 3)
14. BS4 (BSI-DTS 4)
15. YS1 (YSS-928-1)
16. YS2 (YSS-928-2)
17. YS3 (YSS-928-3)
Bus Check
1. VER. (Version information)
2. A/P (Checksum ALL/PROG)
3. 2/M (Checksum 232C/MAKER)
4. PORT (Port check)
Remote control code (key)
7A-90 (PRG 9)
7A-91 (PRG 10)
7A-92 (PRG 11)
7A-93 (PRG 12)
7A-10 (PRESET+)
7A-11 (PRESET-)
7A-12 (PAGE)
7A-0C (CD FF)
7A-88 (PRG 1)
7A-89 (PRG 2)
7A-8A (PRG 3)
7A-8B (PRG 4)
7A-8C (PRG 5)
7A-8F (PRG 8)
–
–
–
–
7A-00 (TP PLAY)
7A-01 (TP RW)
7A-02 (TP FW)
7A-03 (TP STOP)
7A-04 (TP PAUSE)
7A-06 (TP A/B)
7A-09 (CD STOP)
–
–
–
7A-57 (SLEEP)
–
–
7A-0B (CD SKIP-)
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
7A-0A (CD SKIP+)
7A-0D (CD REW)
–
–
–
RX-V800/RX-V800RDS/HTR-5280
• Starting DIAG
Press the “STANDBY/ON key while pressing those two keys indicated in the
figure on the right.
• Starting DIAG in the protection cancel mode
Keys of main unit (in sealing panel)
If the protection function works and causes hindrance to trouble diagnosis, cancel
the protection function as described below, and it will be possible to enter the
DIAG mode. (The protection function other than the excess current detect
function will be cancelled.)
A/B/C/D/E
Press the “STANDBY/ON key while pressing those two keys indicated in the
figure on the right. At this time, keep pressing those two keys for 3 seconds or
longer.
PRESET/
TUNING
Turn on the power while
pressing these keys.
In this mode, the “ZONE2” segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the
protection functions cancelled.
CAUTION!
Note that during the DIAG mode with protection functions cancelled, even when a danger is encountered, protection
functions do not work. Therefore, operating the equipment in this mode may cause danger to it. Use special care for this
point when using this mode.
• Canceling DIAG
[1] Before canceling DIAG, execute setting for PRESET of DIAG menu No.9 (Memory initialization inhibited or Memory
initialized).
* In order to keep the user memory stored, be sure to select PRESET INHI (Memory initialization inhibited).
[2] Turn off the power by pressing the “STANDBY/ON” key of the main unit or the “STANDBY” key of the remote controller.
• Display provided when DIAG started
When the monitor is connected, DIAGNOSTIC MENU appears on its screen as
shown in the figure. (It remains on display until DIAG is cancelled.)
y
ł
ø
œ
ß
ı
ı
ı
ı
ı
ı
ı
ł
ł
ł
ł
The FL display of the main unit displays the protection function history data and the version (1 alphabet) and the DIAG menu
(sub-menu (ANALOG BYPASS) of DIAG menu No.1 DSP THROUGH) a few seconds later.
When there is no history of protection function:
Opening message
When there is no history
of protection function
DIAG menu display
Version (1 alphabet)
After a few seconds
10
RX-V800/RX-V800RDS/HTR-5280
When there is a history of protection function:
When there is a history of
protection function against Version
excess current
(1 alphabet)
Cause: An excessive current flowed to the power amplifier.
Supplementary information: As current of the power transistor is detected, the
abnormal channel can be identified by checking the current detect transistor.
Turning on the power without correcting the abnormality will cause the protection
function to work immediately and the power supply will soon be shut off.
When there is a history of
protection function against
Version
abnormal voltage in the
(1 alphabet)
power supply section
Voltage display in %
When there is a history of
protection function against Version
(1 alphabet)
abnormal DC output
Cause: The voltage in the power supply section is abnormal.
Supplementary information: The abnormal voltage is displayed in % based on
5V as 100%.
Turning on the power without correcting the abnormality will cause the protection
function to work 1 second later and the power supply will be shut off.
Cause: DC output of the power amplifier is abnormal.
Supplementary information: The abnormal voltage is displayed in % based on
5V as 100%.
Turning on the power without correcting the abnormality will cause the protection
function to work 3 seconds later and the power supply will be shut off.
Voltage display in %
* Besides above possible causes for abnormality, a cause may lie in disconnected connector, around CPU, etc.
* For the protection voltage value, refer to DIAG menu No.10 described later.
• History of protection function
When the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted
while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has
been stored.
The history of the protection function is cleared when DIAG is cancelled by selecting RESERVED (Memory initialized) of
DIAG menu No.9 or when the backup data is erased.
• Display during menu operation
During the DIAG operation, the menu list described in the section of the startup screen appears on the superimposed screen
and the function at work is indicated on the FL indicator. The contents displayed during the function operation are described
in the later section on details of functions.
PRESET/
TUNING
• Operation procedure of DIAG menu and SUB-MENU
There are No.1 to No.13 MENU items, each of which has some SUB-MENU
items.
DIAG menu selection
PROGRAM
DIAG menu selection
Main unit: Select the menu using • (Forward) and ¶ (Reverse) keys of
PRESET/TUNIG located in the sealing panel.
Remote control unit: Select the menu using ▲ (Forward) and ▼ (Reverse)keys.
SUB-MENU selection
Use these keys for
DIAG menu selection.
SUB-MENU selection
Main unit: Select the sub-menu using • (Forward) and ¶ (Reverse) keys of
PROGRAM located in the sealing panel.
Remote control unit: Select the sub-menu using • (Forward) and ¶
(Reverse)keys.
ES
COD ET
DIR A
SELECT
ON
* Only the remote control keys indicated in the MENU List can be used to select
a sub-menu directly.
11
DIR B
SCREEN
Use these keys for
SUB-MENU selection.
RX-V800/RX-V800RDS/HTR-5280
• Functions in DIAG mode
In addition to the DIAG menu items, functions as listed below are available.
• Input selection, 6CH input
• REC OUT (ZONE2) switching
• Center/Rear/Sub-woofer level adjustment
• Muting
• Speaker relay A/B
• Power on/off
• Master volume
It is possible to set to the following volume values directly by transmitting remote control codes during the DIAG operation
only.
Volume value (dB) Remove control
code
0
7A-E0
-20
7A-E1
-30
7A-E2
MUTE
7A-E3
Remote control
key
PAGE A
PAGE B
PAGE C
PAGE D
* Functions related to the tuner and the set menu are not available.
* It is possible to confirm Menu No.11 IF STATUS while keeping the signal process (operation status) of each DIAG menu
by using the input mode key of the main unit.
• Initial settings used to start DIAG
Following initial settings are used when starting DIAG.
When DIAG is canceled, these settings are restored to those before starting DIAG.
• Master volume: -40dB
• Input, ZONE2 input: DVD (6CH INPUT OFF)
• Center/Rear/Sub-woofer level: 0dB
• Audio mute: OFF
• Speaker relay A/B: ON
• Speaker setting: LARGE / BASS OUT = BOTH
• DIAG menu: DSP through (analog bypass)
12
RX-V800/RX-V800RDS/HTR-5280
• Details of DIAG menu
1. DSP THROUGH
There are 3 sub-menu items (ANALOG BYPAS, DSP 0dB, DSP FULL BIT).
ANALOG BYPASS [Remote control code: 7A-90 (PRG9)]
• The input mode is fixed to use the analog (A/D) system.
• The L/R signal is output through the analog bypass without using the DSP
block.
• C/SWF, FL/FR, RL/RR signals are output through DSP (see the signal path in
the figure below) without using the external DRAM. (Head margin included)
Head margin:
Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/RR: -12dBFS,
SWFR: Add L/R signal at -20dBFS.
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
D/A
AK4393
R
CODEC
(D/A)
SWFR
L/R
DIGITAL
L/R
L/R
SDOB1
L/R
C
FL
SDOB2
FR
L/R
RL
SDOB3
Sub DSP
AK4527
RR
AC3D3 YSS928
4M DRAM
SDOxx represents a terminal name of AC3D3.
The shaded square (
operate.
13
) means that the element indicated in it does not
RX-V800/RX-V800RDS/HTR-5280
DSP 0dB [Remote control code: 7A-91 (PRG 10)]
• C/SWFR, FL/FR, RL/RR signals are output through DSP (see the signal path
in the figure below) without using the external DRAM. (Head margin included)
Head margin:
Main L/R: 0dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS, RL/
RR: -12dBFS, SWFR: Add L/R signal at -20dBFS.
[2ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
D/A
AK4393
R
CODEC
(D/A)
SWFR
L/R
DIGITAL
L/R
L/R
SDOB1
L/R
C
FL
SDOB2
FR
L/R
RL
SDOB3
Sub DSP
AK4527
RR
AC3D3 YSS928
4M DRAM
[Multi ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
L/R
D/A
AK4393
R
CODEC
(D/A)
SWFR
LS/RS C/LFE
DIGITAL
C/LFE
L/R
SDOB1
C
FL
L/R
SDOB2
FR
SDOB3
RR
RL
LS/RS
Sub DSP
AK4527
AC3D3 YSS928
4M DRAM
SDOxx represents a terminal name of AC3D3.
The shaded square (
operate.
) means that the element indicated in it does not
DSP FULL BIT [Remote control code: 7A-92 (PRG 11)]
• The signal is output in digital full bit without including the head margin.
• The same applies as “DSP 0dB” except that the digital data is output in full bit
at D/A.
• However, the SWFR signal is not output in full bit.
14
RX-V800/RX-V800RDS/HTR-5280
2. HP ROUTE
There are 2 sub-menu items (HP 0dB and HP FULL BIT).
HP 0dB [REMOTE CONTROL CODE: 7A-93 (PRG 12)]
• L/R, C/SWFR, FL/FR, RL/RR signals are output through DSP (see the signal
path in the figure below) without using the external DRAM. (Head margin
included)
• SDOB3 output is input to Main L/R DAC. Other than that, everything is the
same as DSP THROUGH.
Head margin:
Main L/R: -18dBFS, Center: -6dBFS, Rear Center: -3dBFS, FL/FR: -6dBFS,
RL/RR: -18dBFS, SWFR: Add L/R signal at -20dBFS.
[2ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
D/A
AK4393
R
CODEC
(D/A)
SWFR
L/R
DIGITAL
L/R
L/R
SDOB1
Depend on SP Config
L/R
C
FL
SDOB2
FR
SDOB3
RR
L/R
RL
Sub DSP
AK4527
AC3D3 YSS928
4M DRAM
[Multi ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
L/R
D/A
AK4393
R
CODEC
(D/A)
SWFR
LS/RS C/LFE
DIGITAL
C/LFE
L/R
SDOB1
Depend on SP Config
C
FL
L/R
SDOB2
FR
RL
LS/RS
SDOB3
Sub DSP
AK4527
RR
AC3D3 YSS928
4M DRAM
SDOxx represents a terminal name of AC3D3.
The shaded square (
operate.
) means that the element indicated in it does not
HP FULL BIT [Remote control code: 7A-10 (PRESET+)]
• The signal is output in digital full bit without including the head margin.
• The same applies as “HP 0dB” except that the digital data is output in full bit at
D/A.
• However, the SWFR signal is not output in full bit.
15
RX-V800/RX-V800RDS/HTR-5280
3. RAM THROUGH
The main L/R uses the analog through method when analog signals are input and the DSP through method when digital
signals are input.
The Center, FL/FR and RL/RR signals are output through the external DRAM.
RAM 0dB [REMOTE CONTROL CODE: 7A-11 (PRESET-)]
MAIN ATT [REMOTE CONTROL CODE: 7A-12 (PAGE)]
[2ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
D/A
AK4393
R
CODEC
(D/A)
SWFR
L/R
DIGITAL
L→C
SDOB1
L/R
C
FL
L/R
SDOB2
FR
SDOB3
RR
RL
L/R
Sub
DSP
AK4527
AC3D3 YSS928
4M DRAM
[Multi ch source]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
L/R
D/A
AK4393
R
CODEC
(D/A)
SWFR
C/LFE LS/RS
DIGITAL
LFE
L/R
C/LFE
C
SDOB1
C
FL
L/R
SDOB2
FR
SDOB3
RR
RL
LS/RS
Sub DSP
AK4527
AC3D3 YSS928
4M DRAM
SDOxx represents a terminal name of AC3D3.
The shaded square (
operate.
) means that the element indicated in it does not
16
RX-V800/RX-V800RDS/HTR-5280
4. PRO LOGIC [YSS928]
Operation conforming to the ordinary Dolby Normal sound field is provided.
[REMOTE CONTROL CODE: 7A-0C (CD FF)]
[2ch source]
ANALOG
Same as ordinary Pro Logic except that the auto input balance function is off.
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
L/R
D/A
AK4393
R
CODEC
(D/A)
SWFR
C/S
DIGITAL
SDOB1
C
C
FL
SDOB2
FR
SDOB3
RR
RL
S
Sub DSP
AK4527
AC3D3 YSS928
4M DRAM
[Dolby D./dts Normal]
ANALOG
L
CODEC
(A/D)
AK4527
L/R
SDOA0
Main DSP
(Decoder)
INTERNAL
DIR
L/R
D/A
AK4393
R
CODEC
(D/A)
SWFR
C/LFE LS/RS
DIGITAL
C
LFE
SDOB1
C
FL
SDOB2
FR
SDOB3
RR
RL
LS/RS
Sub DSP
AK4527
AC3D3 YSS928
4M DRAM
SDOxx represents a terminal name of AC3D3.
The shaded square (
operate.
17
) means that the element indicated in it does not
RX-V800/RX-V800RDS/HTR-5280
5. SPEAKERS SET
The input signal is automatically identified in the order of dts → DOLBY DIGITAL → PCM → Analog.
There are five sub-menu items as follows. The signals output from the DSP block are the same as 1. DSP THROUGH: DSP
0dB.
MAIN: SMALL 0dB
[Remote control code: 7A-88 (PRG 1)]
MAIN: LARGE -10dB
[Remote control code: 7A-89 (PRG 2)]
LFE: BASS:MAIN
[Remote control code: 7A-8B (PRG 4)]
Front Mix: 5ch
[Remote control code: 7A-8C (PRG 5)]
CENTER: NONE
[Remote control code: 7A-8A (PRG 3)]
The analog switch settings for each sub-menu are as shown in the table below.
1
2
3
4
5
LARGE:
SMALL:
NONE:
Sub-menu
CENTER SP REAR SP
MAIN:SMALL 0dB LARGE
LARGE
MAIN:LARGE -10 LARGE
LARGE
CENTER:NONE
NONE
LARGE
LFE/BASS:MAIN
SMALL
SMALL
FRONT MIX:5CH
LARGE
LARGE
MAIN SP
SMALL
LARGE
LARGE
LARGE
LARGE
MAIN LVL
0dB
-10dB
0dB
0dB
0dB
LFE/BASS
SWFR
BOTH
BOTH
MAIN
BOTH
Signals are output in all bandwidths.
Signals lower than 90Hz are mixed in the channel specified by LFE/BASS.
The center contents are distributed to the MAIN L/R channels after -3dB.
6. DISPLAY CHECK
This program is used to check the FL display section. The display condition varies as shown below according to the submenu operation. The signals are processed using EFFECT OFF (The L/R signal is output using ANALOG MAIN BYPASS.)
The video signal internal/external synchronization switching is controlled by the microprocessor. When the initial message is
displayed and all the FL segments light up, it is switched to the internal synchronization but other than that it is forced to the
external synchronization setting.
Also, except for the initial display, 128 pictographs for checking the OSD driver are used for the video signal output display.
[Remote control code: 7A-8F (PRG 8)]
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
PCM
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
ZONE 2
SLEEP
SP
AB
Initial display
dB
ms
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
All segments OFF
VIRTUAL
PRO LOGIC
DTS
DOLBY
NEWS
PRO LOGIC
1
PTY HOLD
STEREO
NEWS
AFFAIRS
TUNED
Short
VIRTUAL
VOLUME
DIGITAL
PRO LOGIC
DSP
CD
Lighting of segments
in lattice
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
ZONE 2
SLEEP
SP
AB
dB
ms
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
All segments ON (dimmer 100%)
SLEEP
6.1/ES
Lighting in lattice
VIRTUAL
DIGITAL
PRO LOGIC
DSP
6.1/ES
PCM
6.1/ES
PCM
SP
AB
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
ZONE 2
SLEEP
dB
ms
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
All segments ON (dimmer 50%)
Normal
Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation
of the FL driver is checked by using the dimmer control. Then a short between segments next to each other is checked by
turning ON and OFF all segments alternately (in lattice). (In the above example, the segments in the second row from the top
are shorted.)
18
RX-V800/RX-V800RDS/HTR-5280
7. MANUAL TEST
The noise generator with a built-in DSP outputs the test noise through the channels specified by the sub-menu.
The noise frequency for LFE is 35 to 250 Hz. Other than that, the center frequency is 800Hz.
ALL
[Remote control code: 7A-00 (TAPE PLAY)]
MAIN L
[Remote control code: 7A-01 (TAPE RW)]
Noise is output from all channels.
CENTER
[Remote control code: 7A-02 (TAPE FW)]
Noise is output from the MAIN L channel.
MAIN R
[Remote control code: 7A-03 (TAPE STOP)]
Noise is output from the CENTER
channel.
REAR R
REAR L
[Remote control code: 7A-04 (TAPE PAUSE)] [Remote control code: 7A-06 (TAPE A/B)]
Noise is output from the MAIN R channel.
Noise is output from the REAR R channel.
Noise is output from the REAR L
channel.
LFE
[Remote control code: 7A-09 (CD STOP)]
Noise is output from the SUB WOOFER
channel.
8. RS-232C
RX-V800 does not use this menu.
9. PRESET
This menu is used to reserve and inhibit initialization of the back-up RAM. The signals are processed using EFFECT OFF.
(The L/R signal is output using ANALOG MAIN BYPASS.)
PRESET INHIBIT (Initialization inhibited) [REMOTE CONTROL CODE: –]
RAM initialization is not executed. Select this sub-menu to protect the values set
by the user.
PRESET RESERVED (Initialization reserved) [REMOTE CONTROL CODE: 7A57 (SLEEP)]
Initialization of the back-up RAM is reserved. (Actually, initialization is executed
next time when the power is turned on.) Select this sub-menu to reset when
shipped out of the factory or to reset RAM.
19
RX-V800/RX-V800RDS/HTR-5280
10. AD DATA CHECK
This menu is used to display the A/D conversion value of the main CPU which detects panel keys of the main unit and
protection functions in % using the sub-menu. (Reference voltage 5V as 100%) During signal processing, the condition
before execution is maintained.
When in K0/K1 page, it is not possible to operate the keys of the main unit because the values of all keys are detected. But
one click on the volume encoder of the main unit to the right or left will cancel this function and sets to the next sub-menu.
Note, however, that clicking there more than once would change the DIAG menu. In such a case, return to the DIAG menu
which has been used for measurement. During signal processing, the condition before execution of this menu is maintained.
REC OUT [Remote control code: –]
RX-V800 does not use this sub-menu.
K0/K1 (Panel key of main unit) [Remote control code: –]
A/D of the key fails to function properly when the standard value is deviated by
±4%. In this case, check the constant of partial pressure resistor, solder
condition, etc.
[Table 1]
Display
0
10
20
30
40
50
60
70
80
90
100
K0
PRESET ¶
PRESET •
PRESET/TUNING
FM/AM
MEMORY
TUNING MODE
RDS MODE
RDS EON
PTY MODE
PTY START
KEY OFF
K1
6CH INPUT
INPUT ¶
INPUT •
INPUT MODE
SPEAKERS A
SPEAKERS B
EFFECT
PROGRAM ¶
PROGRAM •
A/B/C/D/E
KEY OFF
DC/PS (Protection) [REMOTE CONTROL CODE: 7A-0B (CD SKIP-)]
DC: DC detect protection value (Normal value: 1 to 13)
PS: Power voltage protection value (Normal value: 18 to 32)
* If DC or PS is out of the normal value range, the protection function works to
turn off the power.
20
RX-V800/RX-V800RDS/HTR-5280
11. IF STATUS
Using the sub-menu, the status data is displayed one after another in the hexadecimal notation.
During signal processing, the status before execution of this menu is maintained.
* Numeric values in the figure example are for reference.
IST (Internal status) [REMOTE CONTROL CODE: –]
Indicates the status information of the microprocessor.
5th byte
4th byte
3rd byte
2nd byte
1st byte
<1st byte> Digital input/output setting value
Upper 4 bits: REC OUT selected/lower 4 bits: INPUT selected
Numeric
value
0
1
2
3
Selection
NONE
FRONT
OPT1
OPT2
Numeric
value
4
5
6
7
Selection
OPT3
OPT4
OPT5
OPT6
Numeric
value
8
9
A
B
Selection
COAX1
COAX2
COAX4
COAX5
Numeric
value
C
D
Selection
COAX3
RF
<2nd byte> Fs information of reproduction signal
Display
Fs (kHz)
00
Analog
01
32
02
44.1
03
48
04
64
05
88.2
06
96
07
Unknown NRM
08
Unknown DBL
<3rd byte> Audio code mode information of reproduction signal
Display
Audio Code
00
1+1
01
1/0
02
2/0
03
3/0
04
2/1
05
3/1
06
2/2
07
3/2
08
2/3
09
3/3
0A
dts7.1
<4th byte> Format information of reproduction signal
*1: Analog processing is used as digital reproduction is not
possible because of a commercial bit or 4-ch audio reason.
Display
00
01
02
03
04
05
06
07
08
09
0A
0B
Signal format
Analog (Unlock)
Incorrect digital (*1)
Digital Data
IEC1937 Data
PCM Audio
Dolby Digital
D.D.Karaoke
D.D.EX
RED dts
ORANGE dts
dts ES
NONE PCM
<5th byte> Signal processing status information
*2: With digital signals other than 32kHz, 44.1kHz and 48kHz,
through processing method is used for reproducible signals.
21
bit7
bit6
MUTE request
Red dts flashing
bit5
bit4
6.1ch. sound field being processed
FULL MUTE (ON: 1)
bit3
–
bit2 Through & bypass (*2)
bit1
bit0
–
dts analog mute
0B
Not defined
09
Not defined
RX-V800/RX-V800RDS/HTR-5280
CS1-5 [Remote control code: -]: Indicates channel status information of the input signal (IEC60958).
BI1-4 [Remote control code: -]: Indicates information of the bit stream included in the DOLBY DIGITAL signal.
BS1-4 [Remote control code: -]: Indicates information of the bit stream included in the dts signal.
YS1-3 [Remote control code: - ] Indicates device status information of YSS928 (IC501). * The numeric value in the figure is
an example for reference.
Byte No.
1
2
3
4
5
Function
YSS MUTE Reg
YSS MODE Reg
YSS IPORT BIT 7-0
YSS IPORT BIT 14-8
YSS OPORT
Byte No.
1
2
3
4
5
Function
IEC 1937 Preamble Pc
AC-3 Data Stream No
AC-3D Decode Status
YSS ZERO Reg
MIREG
Byte No.
1
2
3
4
Function
DIR Status
DIR fs
DIR fs count
YSS ZEROBF
12. DSP RAM CHECK
This menu is used to self-diagnose whether or not bus connection of YSS928 (IC501) and the external RAM (IC502) is made
properly.
During signal processing, the status before execution of this menu is maintained.
Bus Check [Remote control code: 7A-0A (CD SKIP+)]
The address bus and the data bus are checked and the connection condition is
displayed.
When no error is detected, "NoEr" appears on display.
Display
WAIT
NoEr
Description
Bus being checked.
No error detected.
DATA
ADDR
Data bus shorted or open.
Address bus shorted or open.
22
RX-V800/RX-V800RDS/HTR-5280
13. MICROPROCESSOR INFORMATION
There are 4 sub-menu display.
The version, checksum and the port specified by the microprocessor are displayed. The signal is processed using EFFECT
OFF. The checksum is obtained by adding the data at every 16 bits for each program area and expressing the result as a 4figure hexadecimal data.
Version [Remote control code: 7A-0D (CD REW)]
Release 1 figure / Main 2 figures / DSP 2 figures / Communication 1 figure / Boot
manufacturer 1 figure / Boot 232c 1 figure
Checksum [Remote control code: –]
A : All
P : Program area
Checksum [Remote control code: –]
2 : Boot 232C M : Boot manufacturer
Check of port setting for judging microprocessor function [Remote control
code: –]
¡
ß
œ
ø
ł
Tuner mode 0 (*1)
Tuner mode 1 (* 1)
RDS with (1) / without (0)
Model type: DSP-AX2 (1) / RX-V3000 (0)
ZONE2 with (1) / without (0)
VIDEO format: PAL (1) / NTSC (0)
Head phone: Unconnected (1) / connected (0)
Tuner: Not stereo (1) / stereo (0)
) 0 ;
*1
Tuner mode 0
0
0
1
Tuner mode 1
0
1
0
1
1
Tuner frequency
AM: 531-1611kHz/9kHz FM: 76.0-90.0MHz/100kHz
AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz
AM: 530-1710kHz/10kHz FM: 87.5-107.9MHz/200kHz
R destination, Port6: LOW AM: 530-1710kHz/10kHz FM: 87.5-108.0MHz/100kHz
HIGH AM: 531-1611kHz/9kHz FM: 87.5-108.0MHz/50kHz
■ AMP ADJUSTMENT
Confirmation of Idling Current of Main (1) P. C. B.
0.1mV ~ 10.0mV
(DC)
• Right after power is turned on, confirm that the voltage
across the terminals of R65 (Main Lch), R72 (Main
Rch), R86 (Center), R77 (Rear Lch), R83 (Rear Rch)
are between 0.1mV and 10.0mV.
• If it exceeds 10.0mV, open (cutoff) R3 (Main Lch), R38
(Main Rch), R55 (Center), R45 (Rear Lch), R50 (Rear
Rch) and reconfirm the voltage.
• Confirm that the voltage is 0.20mV ~ 15.0mV after 60
minutes.
R65 (MAIN Lch)
R72 (MAIN Rch)
R86 (CENTER)
Cut off
R31 (MAIN Lch)
R38 (MAIN Rch)
R55 (CENTER)
R45 (REAR Lch)
R50 (REAR Rch)
23
0.1mV ~ 10.0mV
(DC)
R77 (REAR Lch)
R83 (REAR Rch)
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
■ DISPLAY DATA
y
1
● V901 : 16-BT-81GK (V5917600)
PATTERN AREA
● PIN CONNECTION
Pin No.
65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
Connection F2 F2 NP P37 P36 P35 P34 P33 P32 IC NP Fd Fd NP IC P31 P30 P29 P28 P27 P26 P25 P24 P23 P22 P21 P20 P19 P18 P17 P16 P15 P14
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Pin No.
Connection P13 P12 P11 P10 P9 P8 P7 P6 P5 P4 P3 P2 P1 16G 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP F1 F1
Note : 1) F1, F2 ..... Filament 2) NP ..... No pin 3) DL ..... Datum Line 4) 1G ~ 16G ..... Grid
5) IC ..... Internal connection (IC pin should be electrically open on the PC board.) 6) Fd terminals are to be supplied through 51kΩ from Ec.
7) Field of vision is a minimum of 36˚ from the upper side. 26˚ from the lower side.
● GRID ASSIGNMENT
VIRTUAL
15G
DTS MOVIE THEATER 12
DOLBY DIGITAL
PRO LOGIC ENTERTAINMENT
DIGITAL
PRO LOGIC
DSP
6.1/ES
PCM
16G
PS PTY RT CT
PTY HOLD EON STEREO AUTO
NEWS INFO AFFAIRS SPORT
MEMORY TUNED
VOLUME
ZONE 2
SLEEP
SP
AB
1G
1-1
2-1
3-1
4-1
5-1
1-2
2-2
3-2
4-2
5-2
1-3
2-3
3-3
4-3
5-3
1-4
2-4
3-4
4-4
5-4
1-5
2-5
3-5
4-5
5-5
1-6
2-6
3-6
4-6
5-6
1-7
2-7
3-7
4-7
5-7
2G
3G
4G
5G
6G
7G
8G
9G
10G 11G 12G 13G
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
V-AUX
CABLE
D-TV/LD
CBL/SAT
VCR 1
VCR2/DVR
dB
V-AUX
ms
14G
S3
B19
S2
B2
B1
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
S1
DVD
MD/TAPE
CD-R
TUNER
CD
PHONO
(1G~14G)
● ANODE CONNECTION
16G
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
15G
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
14G
1-1
2-1
3-1
4-1
5-1
1-2
2-2
3-2
4-2
5-2
1-3
2-3
3-3
4-3
5-3
1-4
2-4
3-4
4-4
13G~1G
1-1
2-1
3-1
4-1
5-1
1-2
2-2
3-2
4-2
5-2
1-3
2-3
3-3
4-3
5-3
1-4
2-4
3-4
4-4
16G
P20
P21
P22
P23
P24
P25
P26
P27
P28
P29
P30
P31
P32
P33
P34
P35
P36
P37
(PS)
(PTY)
15G
B17
P18
B19
(RT)
(CT)
S1
S2
S3
14G
5-4
1-5
2-5
3-5
4-5
5-5
1-6
2-6
3-6
4-6
5-6
1-7
2-7
3-7
4-7
5-7
13G~1G
5-4
1-5
2-5
3-5
4-5
5-5
1-6
2-6
3-6
4-6
5-6
1-7
2-7
3-7
4-7
5-7
–
–
E-24/J-20
E-25/J-21
DIRMCK
Control Register
SELOB
µ-COM Interface
SELB SELA
SYNC
U
FS128
C
6
7
VMOD
BS
DBL/V
BSMOD
ERR
5
DIRO Interface
SDIASEL
SDIA Interface
DBL
PLL
Clock at DIR
(25 MHz)
CRC
PLL
DSP Clock
(30 MHz)
DIRPRO
DIRPCO
SDIA
DIRSDO
ZEROFLG
NONPCM
DTSDATA
AC3DATA
CRC
MUTE
KARAOKE
SURNEC
CPO
XO
XI
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
IPORT5-7
DDINSEL
Main DSP
(AC-3/ProLogic/DTS Decorder)
V
UMOD
SDIBCKSEL
DIR
C, LFE
SDDA Interface
LS, RS
SDIB3
SDIB2
SDIB1
SDIB0
SDOA2
SDOA1
SDOA0
SDIB1
SDIB0
VSS
VDD2
IPORT12
IPORT13
IPORT14
DIRSDO
DIRWCK
DIRBCK
DIRMCK
ERR/BS
SYNC/U
FS128/C
DBL/V
SDWCKI1
SDBCKI1
VSS
SDOB3
SDOB2
SDOB1
SDOB0
VDD1
ZEROBF3R
ZEROBF3L
ZEROBF2R
ZEROBF2L
OPORT0
OPORT1
OPORT2
OPORT3
OPORT4
OPORT5
OPORT6
OPORT7
VSS
VDD2
RAMD0
RAMD1
RAMD2
YSS928
CMOD
Contorol Signals
DIRWCK
DIRBCK
SDBCKI1
SDIACKSEL
SDWCKI1
SDWCKI0
SDBCKI0
/SDBCKO
IPORT0-4
MPLOAD
IPORT8-14
SDOB0
L, R
SDIBSEL
RAMA0-17
RAMOEN
RAMWEN
RASN
CASN
RAMD0-15
External
Memory
Interface
IPINT
Coefficient,
Program
RAM
SDIB Interface
OVFB/END
OVFSEL
So
SDOBCKSEL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
/cs
SELOA
SubDSP
XO
XI
SELI1
SELI0
SELOA
SELOB
TESTMS
TESTXEN
IPORT0
IPORT1
IPORT2
IPORT3
IPORT4
DDIN0
DDIN1
DDIN2
DDIN3
VSS
CPO
AVDD
DIRPCO
DIRPRO
AVSS
TESTBRK
TESTR1
TESTR2
VDD1
SDWCKI0
SDBCKI0
/SDBCKO
IPORT8
IPORT9
IPORT10
IPORT11
SDIA
SDOA2
SDOA1
SDOA2
SDIB3
SDIB2
SI
SDOB1
END
SDOB3
OVFB
ZEROBF3R-0L
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
VDD2
TESTXO
TESTXI
SELI2
SELI3
VSS
SELI4
IPINT
/IC
SCK
SI
SO
/CS
DIRINT
/LOCK
CRC
SURENC
VDD1
KARAOKE
MUTE
AC3DATA
DTSDATA
NONPCM
VSS
ZEROFLG
OVFB/END
RAMA17
RAMA16
RAMA15
RAMA14
RAMA13
RAMA12
SELI5
SELI6
SELI7
SELI8
VDD2
VSS
RAMA11
RAMA10
IC501 : YSS928
PHONO EQ
SCK
SDOB2
SDOB Interface
■ IC DATA
OPORT0-7
SELI0-13
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
RAMA9
RAMA3
RAMA4
SELI9
SELI10
SELI11
SELI12
SELI13
RAMA2
RAMA5
RAMA1
RAMA6
RAMA0
RAMA7
RAMA8
VDD1
VSS
RASN
RAMOEN
RAMWEN
CASN
RAMD15
RAMD14
RAMD13
RAMD12
RAMD11
RAMD10
RAMD9
RAMD8
VDD1
VSS
RAMD7
RAMD6
RAMD5
RAMD4
ZEROBF0L
ZEROBF0R
ZEROBF1L
ZEROBF1R
RAMD3
/LOCK
ERR/BS
DDIN3
DDIN2
DDIN1
DDIN0
DIRINT
SYNC/U
FS128/C
RX-V800/RX-V800RDS/HTR-5280
IC501 : YSS928
Pin Description
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Name
XO
XI
SELI1
SELI0
SELOA
SELOB
TESTMS
TESTXEN
IPORT0
IPORT1
IPORT2
IPORT3
IPORT4
DDIN0
DDIN1
DDIN2
DDIN3
VSS
CPO
AVDD
DIRPCO
DIRPRO
AVSS
TESTBRK
TESTR1
TESTR2
VDD1
SDWCKI0
SDBCKI0
/SDBCKO
IPORT8
IPORT9
IPORT10
IPORT11
SDIA
SDOA2
SDOA1
SDOA0
SDIB3
SDIB2
SDIB1
SDIB0
VSS
VDD2
IPORT12
IPORT13
IPORT14
DIRSDO
DIRWCK
DIRBCK
DIRMCK
ERR/BS
SYNC/U
FS128/C
DBL/V
SDWCKI1
SDBCKI1
VSS
SDOB3
SDOB2
SDOB1
SDOB0
VDD1
ZEROBF3R
ZEROBF3L
ZEROBF2R
ZEROBF2L
OPORT0
OPORT1
OPORT2
OPORT3
OPORT4
OPORT5
OPORT6
OPORT7
I/O
O
I
I+
I+
O+
O+
I+
I+
I+
I+
I+
I+
I+
Is
Is
Is
Is
–
A
–
A
A
–
I+
I+
I+
–
I+
I+
O
I+
I+
I+
I+
I
O
O
O
I+
I+
I+
I+
–
–
I+
I+
I+
O
O
O
O
O
O
O
O
I+
I+
–
O
O
O
O
–
O+
O+
O+
O+
O
O
O
O
O
O
O
O
Function
Crystal oscillator connection terminal
Crystal oscillator connection terminal (24.576 MHz)
Built-in selector input 1
Built-in selector input 0
Built-in selector A output
Built-in selector B output
Test terminal Unconnected
Test terminal Unconnected
General purpose input terminal
General purpose input terminal
General purpose input terminal
General purpose input terminal
General purpose input terminal
DIR: Digital audio interface data input terminal 0
DIR: Digital audio interface data input terminal 1 / general purpose input terminal
DIR: Digital audio interface data input terminal 2 / general purpose input terminal
DIR: Digital audio interface data input terminal 3 / general purpose input terminal
GND
PLL filter connection terminal
+3.3V power supply (for DIR block)
DIR: PLL filter connection terminal
DIR: PLL filter connection terminal
GND (for DIR block)
Test terminal Unconnected
PLL initialize signal input terminal for DSP
Test terminal Unconnected
+3.3V power supply (for terminal block)
Word clock input terminal for SDIA, SDOA, SDIB, SDOB interfaces
Word clock input terminal for SDIA, SDOA, SDIB, SDOB interfaces
Inverted clock output terminal for inverted clock of DIRBCK or SDBCKI0
IPINT compatible general purpose input terminal
IPINT compatible general purpose input terminal
IPINT compatible general purpose input terminal
IPINT compatible general purpose input terminal
bitstream or PCM data input terminal to MainDSP
Output terminal for PCM from MainDSP (C, LFE output)
Output terminal for PCM from MainDSP (LS, RS output)
Output terminal for PCM from MainDSP (L, R output)
Input terminal 3 for PCM to SubDSP
Input terminal 2 for PCM to SubDSP
Input terminal 1 for PCM to SubDSP
Input terminal 0 for PCM to SubDSP
GND
+2.5V power supply (for internal circuit)
IPIN compatible general purpose input terminal
IPIN compatible general purpose input terminal
IPIN compatible general purpose input terminal
bitstream or PCM data output terminal from DIR
DIR: Serial data word clock (fs) output terminal
DIR: Serial data bit clock (64fs) output terminal
DIR: Serial data master clock (256fs or 128fs) output terminal
DIR: Data error detect / block start output terminal
DIR: Serial data synchronous timing / user data output terminal
DIR: Serial data master clock 128fs / channel status output terminal
DIR: Double rate lock detect / parity flag output terminal
Word clock input terminal for SDIB, SDOB interface
Bit clock input terminal for SDIB, SDOB interface
GND
Output terminal for PCM from SubDSP
Output terminal for PCM from SubDSP
Output terminal for PCM from SubDSP
Output terminal for PCM from SubDSP
+3.3V power supply (for terminal block)
SDOB3 Rch zero flag output terminal
SDOB3 Lch zero flag output terminal
SDOB2 Rch zero flag output terminal
SDOB2 Lch zero flag output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
General purpose output terminal
26
RX-V800/RX-V800RDS/HTR-5280
No.
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
27
Name
VSS
VDD2
RAMD0
RAMD1
RAMD2
RAMD3
ZEROBF1R
ZEROBF1L
ZEROBF0R
ZEROBF0L
RAMD4
RAMD5
RAMD6
RAMD7
VSS
VDD1
RAMD8
RAMD9
RAMD10
RAMD11
RAMD12
RAMD13
RAMD14
RAMD15
CASN
RAMWEN
RAMOEN
RASN
VSS
VDD1
RAMA8
RAMA7
RAMA0
RAMA6
RAMA1
RAMA5
RAMA2
SELI13
SELI12
SELI11
SELI10
SELI9
RAMA4
RAMA3
RAMA9
RAMA10
RAMA11
VSS
VDD2
SELI8
SELI7
SELI6
SELI5
RAMA12
RAMA13
RAMA14
RAMA15
RAMA16
RAMA17
OVFB/END
ZEROFLG
VSS
NONPCM
DTSDATA
AC3DATA
MUTE
KARAOKE
VDD1
SURENC
CRC
/LOCK
DIRINT
/CS
SO
SI
SCK
/IC
IPINT
I/O
–
–
I+/O
I+/O
I+/O
I+/O
O+
O+
O+
O+
I+/O
I+/O
I+/O
I+/O
–
–
I+/O
I+/O
I+/O
I+/O
I+/O
I+/O
I+/O
I+/O
O
O
O
O
–
–
O
O
O
O
O
O
O
I+
I+
I+
I+
I+
O
O
O
O
O
–
–
I+
I+
I+
I+
O
O
O
O
O
O
O
O
–
O
O
O
O
O
–
O
O
O
O
Is
Ot
Is
Is
Is
O+
Function
GND
+2.5V power supply (for internal circuit)
SubDSP: Data terminal 0 for external memory
SubDSP: Data terminal 1 for external memory
SubDSP: Data terminal 2 for external memory
SubDSP: Data terminal 3 for external memory
SDOB1 Rch zero flag output terminal
SDOB1 Lch zero flag output terminal
SDOB0 Rch zero flag output terminal
SDOB0 Lch zero flag output terminal
SubDSP: Data terminal 4 for external memory
SubDSP: Data terminal 5 for external memory
SubDSP: Data terminal 6 for external memory
SubDSP: Data terminal 7 for external memory
GND
+3.3V power supply (for terminal block)
SubDSP: Data terminal 8 for external memory
SubDSP: Data terminal 9 for external memory
SubDSP: Data terminal 10 for external memory
SubDSP: Data terminal 11 for external memory
SubDSP: Data terminal 12 for external memory
SubDSP: Data terminal 13 for external memory
SubDSP: Data terminal 14 for external memory
SubDSP: Data terminal 15 for external memory
SubDSP: Column address strobe output terminal for external DRAM
SubDSP: Write enable output terminal for external memory
SubDSP: Output enable output terminal for external memory
SubDSP: Low address strobe output terminal for external DRAM
GND
+3.3V power supply (for terminal block)
SubDSP: Address terminal 8 for external memory
SubDSP: Address terminal 7 for external memory
SubDSP: Address terminal 0 for external memory
SubDSP: Address terminal 6 for external memory
SubDSP: Address terminal 1 for external memory
SubDSP: Address terminal 5 for external memory
SubDSP: Address terminal 2 for external memory
Built-in selector input 13
Built-in selector input 12
Built-in selector input 11
Built-in selector input 10
Built-in selector input 9
SubDSP: Address terminal 4 for external memory
SubDSP: Address terminal 3 for external memory
SubDSP: Address terminal 9 for external memory
SubDSP: Address terminal 10 for external memory
SubDSP: Address terminal 11 for external memory
GND
+2.5V power supply (for internal circuit)
Built-in selector input 8
Built-in selector input 7
Built-in selector input 6
Built-in selector input 5
SubDSP: Address terminal 12 for external memory
SubDSP: Address terminal 13 for external memory
SubDSP: Address terminal 14 for external memory
SubDSP: Address terminal 15 for external memory
SubDSP: Address terminal 16 for external memory
SubDSP: Address terminal 17 for external memory
SubDSP: Overflow / program end detect terminal
MainDSP: Zero flag output terminal
GND
Main DSP: non-PCM data detect terminal
MainDSP: DTS data detect terminal
MainDSP: AC-3 data detect terminal
MainDSP: Auto mute detect terminal
MainDSP: AC-3 Karaoke data detect terminal
+3.3V power supply (for terminal block)
MainDSP: AC-3 2/0 mode Dolby Surround Encode input detect terminal
MainDSP: AC-3 CRC error detect terminal
DIR: PLL lock detect terminal
DIR: Interrupt output terminal
Microprocessor interface chip select input terminal
Microprocessor interface data output terminal
Microprocessor interface data input terminal
Microprocessor interface clock input terminal
Initial clear input terminal
Output terminal for interrupt by IPORT8-14
RX-V800/RX-V800RDS/HTR-5280
No.
154
155
156
157
158
159
160
Name
SELI4
VSS
SELI3
SELI2
TESTXI
TESTXO
VDD2
I/O
I+
–
I+
I+
I
O
–
Function
Built-in selector input 4
GND
Built-in selector input 3
Built-in selector input 2
Test terminal Must be connected with VSS.
Test terminal Unconnected.
+2.5V power supply (for internal circuit)
Is: Schmidt trigger input terminal
I+: Input terminal with pulled-up resistor
O: Digital output terminal
Ot: 3-state digital output terminal
A: Analog terminal
28
P40/A16(MA8)
P41/A17(MA9)
VSS
78
77
76
P43/A19(MA11)
P37/A15(MA7)(/D15)
79
73
P36/A14(MA6)(/D14)
80
P42/A18(MA10)
P35/A13(MA5)(/D13)
81
VCC
P34/A12(MA4)(/D12)
82
74
P31/A9(MA1)(/D9)
P33/A11(MA3)(/D11)
83
P124
P32/A10(MA2)(/D10)
VSS
93
85
P27/A7(/D7)
94
84
P26/A6(/D6)
95
P123
P25/A5(/D5)
96
86
P24/A4(/D4)
97
P122
P23/A3(/D3)
98
87
P22/A2(/D2)
99
P121
P21/A1(/D1)
100
88
P20/A0(/D0)
101
P120
P17/D15/INT5
102
89
P16/D14/INT4
103
90
P15/D13/INT3
104
P30/A8(MA0)(/D8)
P14/D12
105
VCC
P13/D11
106
91
P12/D10
107
92
P11/D9
108
IC526 : M30802SGP
16bit µ-COM (Main CPU)
75
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
P10/D8
109
72
P44/CS3/A20(MA12)
P07/D7
110
71
P45/CS2/A21
P06/D6
111
70
P46/CS1/A21
P05/D5
112
69
P47/CS0/A23
P04/D4
113
68
P125
P114
114
67
P126
P113
115
66
P127
P112
116
65
P50/WRL/WR/CASL
P111
117
64
P51/WRH/BHE/CASH
P110
118
63
P52/RD/DW
P03/D3
119
62
P53/BCLK/ALE/CLKOUT
P02/D2
120
61
P130
P01/D1
121
60
P131
P00/D0
122
59
VCC
P157
123
58
P132
P156
124
57
VSS
P155
125
56
P133
P154
126
P153
127
P152
128
P151
VSS
M30802SGP
55
P54/HLDA/ALE
54
P55/HOLD
53
P56/ALE/RAS
129
52
P57/RDY
130
51
P134
P150
131
50
P135
VCC
132
49
P136
P107/AN7/K13
133
48
P137
P106/AN6/K12
134
47
P60/CYS0/RTS0
36
35
34
33
32
31
30
29
11
28
P70/TXD2/SDA2/TA0OUT (*1)
/SCL4/STXD4
27
P57/TXD1
37
26
38
144
25
143
24
VCC
AVCC
R91/AD1RG/RXD4
23
39
22
142
21
P66/RXD1
VREF
20
40
19
141
18
VSS
P100/AN0
17
41
16
140
15
P65/CLK1
AVSS
14
42
13
139
12
P64/CTS1/RTS1/CTS0/CLKS1
P101/AN1
10
43
9
138
8
P63/TXD0
P102/AN2
7
44
6
137
5
P62/RXD0
P103/AN3
4
P61/CLK0
45
3
46
136
2
135
1
P105/AN5/K11
P104/AN4/K10
8
I/O Port
Port P0
8
Port P1
8
8
Port P2
Port P3
8
8
Port P4
Port P5
8
Port P6
Inside Function
Timer
System clock
RAM
10K
M16C/80 Series 16 bit CPU
Watching Timer
(15 bit)
7
Port P13
8
Port P12
8
Port P11
5
8
8
Port P14
Port P10
Multiplication
Controller
8
DMA
Controller
SVF
SVP
VCT
Port P15
E-29/J-25
DRAM
Controller
FLG
INTB
ISP
USP
PC
Port P9
D-A Converter
(8 bit x 2 ch)
Register
R0H
R0H R0L
R0L
R1H
R1H R1L
R1L
R2
R2
R3
R3
SVP
SVP
VCT
VCT
SVP
SVP
VCT
VCT
Port P85
CRC arithmetic Circuit (CCITT)
(X16+X12+X5+1)
7
Memory
X-Y Converter
(16 bit x 16 bit)
8
XIN - XOUT
XCIN - XCOUT
UART/Clock Synchronized
SI/O (8 bit x 5 ch)
Port P8
A-D Converter (10 bit x 8 ch,
Possible to 10 ch)
Port P7
Timer TA0 (16 bit)
Timer TA1 (16 bit)
Timer TA2 (16 bit)
Timer TA3 (16 bit)
Timer TA4 (16 bit)
Timer TB0 (16 bit)
Timer TB1 (16 bit)
Timer TB2 (16 bit)
Timer TB3 (16 bit)
Timer TB4 (16 bit)
Timer TB5 (16 bit)
P71/RXD2/SCL2/TA0IN/TB0IN (*1)
P72/CLK2/TA1OUT/V
P73/CTS2/RTS2/TA1IN/V
P74/TA2OUT/W
P75/TA2IN/W
P76/TA3OUT
P77/TA3IN
P80/TA4OUT/U
P82/INT0
P81/TA4IN/U
P83/INT1
P85/NMI
P84/INT2
VCC
XIN
VSS
XOUT
RESET
P86/XCOUT
P87/XCIN
CNVSS
BYTE
P140
P141
P142
P143
P144
P145
P146
P90/TB0IN/CLK3
P91/TB1IN/RXD3/SCL2/STXD3
P92/TB2IN/TXD3/SDA3/SRXD3
P93/DA0/TB3IN/CTS3/RTS3/SS3
P94/DA1/TB4IN/CTS4/RTS2/SS4
P95/ANEX0/CLK4
P96/ANEX1/TXD4/SDA4/SRXD4
(*1) N channnel Open Drain Output
RX-V800/RX-V800RDS/HTR-5280
IC526 : M30802SGP
Pin Description
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
Port No.
P96
P95
P94
P93
P92
P91
P90
P146
P145
P144
P143
P142
P141
P140
BYTE
CNVss
P87
P86
RESET
XOUT
VSS
XIN
VCC
P85
P84
P83
P82
P81
P80
P77
P76
P75
P74
P73
P72
P71
P70
P57
VCC
P66
VSS
P65
P64
P63
P62
P61
P60
P137
P136
P135
P134
P57
P56
P55
P54
P133
VSS
P132
VCC
P131
P130
P53
P52
P51
P50
P127
P126
P125
P47
P46
P45
P44
P43
VCC
P42
Function name
TXDR
RTS
CTS
FAN
SDTN
RXRDS
SCKN
E/I
CEBU
/FLR
CEM0
CEM1
RDSE
CES
BYTE
CNVss
MODEL
BOOT
RESET
XOUT
VSS
XIN
VCC
NMI
REM1
PEW
PDET
VSY
/ICD
RXDR
/DMT
INT928
I/O
O
I/O
I
I
O
I
SCK
O
O
O
O
O
O
O
VSS
VCC
I
I
I
O
VSS
I
I
I
I
I
I
I
O
I
O
I
Detail of function
232C transmission data / Yokokawa data transmission
232C RTS output / Yokokawa clock input
232C CTS input
Fan control
None audio serial transmission data (necessary port)
RDS received / Frequency switch (R version)
None audio serial clock
Outside / inside synchronized output
BU2092CE or ZONE2
FL IC reset
FL1 enable
FL2 enable
RDS enable or RDS
Onscreen enable output / N/P format
Vss at 16 bit data
Vcc at microprocessor mode
Model distinction
Boot terminal for Yokokawa tool
Reset
Oscillate output
Microcomputer ground
Oscillate input
Microcomputer power supply +5V
Pullup by Vcc / 232C boot
Remote control pulse input and LO edge interrupted
Power switch and HI edge interrupted
Power detect and LO edge interrupted
Vertical synchronized detect
IC YSS928 / DA / AD / CODEC / DEM
232C receive data (connect to pin 29)
Digital full mute
YSS928 IPINT / MUTE / DIR
CEP
SCKP
RDTP
SDTP
SDM
VCC
SDD
VSS
SCK
/CSA
CEC
CEC
SCKC
CSV
/CSM
VRB
VRA
PRI
O
O
I
O
O
VCC
I
VSS
SCK
O
O
O
SCK
O
O
I
I
I
PLL IC enable
PLL IC clock
PLL IC receive data
PLL IC transmission data (necessary PU)
YSS928 transmission data
Microcomputer power supply +5V
YSS928 receive data
Microcomputer ground
YSS928 clock
YSS928 CE
CS3310 serial transmission data
CS3310 enable
CS3310 serial clock
CS3310 power supply control
CS3310 reset
Volume rotary B
Volume rotary A
Current protection
/BEC
VSS
/Z2MT
VCC
/HPMT
/FMTF
O
VSS
O
VCC
O
O
Bus extension control
Microcomputer ground
Zone 2 mute
Microcomputer power supply +5V
Headphone mute
Full mute FL / FR / MAIN -3dB
ON
O
I/O
I
I
SO
SI
SCK
O
O
O
O
O
O
O
Vss
Vcc
I
I
–
–
–
–
–
–
I
I
I
I
O
I
O
I
O
O
O
I
O
SO
OFF
OL
OL
I
I
OL
I
OL
OL
OL
OL
OL
OL
OL
OL
Vss
Vcc
I
I
–
–
–
–
–
–
I
I
I
I
OL
I
OL
I
OL
OL
OL
I
OL
OL
BU
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
Vss
Vcc
OL
OL
–
–
–
–
–
–
OL
OL
I
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
SI
I
OL
SCK
O
SO
O
SCK
O
O
I
I
I
OL
OL
OL
OL
OL
OL
OL
I
I
I
O
OL
OL
OL
OL
OL
OL
OL
OL
OL
OL
I
HI
HI
HI
HI
OL
O
OL
OL
O
O
OL
OL
O
O
O
OL
OL
OL
OL
OL
HI
HI
HI
HI
OL
OL
OL
Just before
Just before
Just before
Just before
Just before
OE
/FMTS
/FMTC
/FMTM
VCC
O
O
O
VCC
WE
Full mute SWL / SWR / SW MONO
Full mute CENTER
Full mute MAIN L / R, RL / RC / RR"
Microcomputer power supply +5V
Just before
30
RX-V800/RX-V800RDS/HTR-5280
No.
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
Port No.
VSS
P41
P40
P37
P36
P35
P34
P33
P32
P31
P124
P123
P122
P121
P120
VCC
P30
VSS
P27
P26
P25
P24
P23
P22
P21
P20
P17
P16
P15
P14
P13
P12
P11
P10
P07
P06
P05
P04
P114
P113
P112
P111
P110
P03
P02
P01
P00
P157
P156
P155
P154
P153
P152
P151
VSS
P150
VCC
P107
P106
P105
P104
P103
P102
P101
AVSS
P100
VREF
AVCC
P91
Voltage
31
Function name
VSS
I/O
VSS
Detail of function
Microcomputer ground
ON
SCKA
SDTA
CEL
RIMA
RIMB
VCC
O
O
O
O
O
VCC
Clock output for audio IC
Data output for audio IC
Enable output for audio IC of sanyo
Power rimitter A
Power rimitter B
Microcomputer power supply +5V
VSS
VSS
Microcomputer ground
O
O
O
O
O
OFF
BU
OL
OL
OL
OL
OL
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
OL
OL
OL
OL
OL
Just before
/MLV
PRY
SPE
SPB
SPA
O
O
O
O
O
TUN0
TUN1
ISA/BSW
ISB/PSW
/HP
TMT
/TUNED
VSS
/ST
VCC
RMV
REC
PREMT
ADKEY1
ADKEY0
AN2
AN1
VSS
AN0
VREF
AVCC
RXDR
0.0
0.5
I
I
I
I
I
O
I
VSS
I
VCC
I
I
I
I
I
I
I
VSS
I
VCC
VCC
I
1.0
Main level
Power relay
Speaker relay at effect
Speaker relay at main B
Speaker relay at main A
O
O
O
O
O
OL
OL
OL
OL
OL
Tuner step 0
Tuner step 1
Program rotary A / BASS EXT switch
Program rotary B / PR.DIRECT switch
Headphone detect
Tuner mute
Tuner meter
Microcomputer ground
Tuner stereo
Microcomputer power supply +5V
Power rimitter for model distinction
REC OUT selector
Power rimitter detect
Key tact switch 1
Key tact switch 0
Temperature detect
Power amplifier DC protection
AD ground
Power supply protection
AD reference
AD power supply
232C receive data / Yokokawa data receive
I
I
I
I
I
O
I
I
I
I
I
I
OL
I
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
Just before
OL
OL
OL
OL
OL
Just before
Just before
Just before
Just before
OL
OL
OL
OL
OL
OL
OL
I
I
OL
I
I
I
I
I
I
I
VSS
I
VCC
VCC
I
I
I
I
I
I
I
I
VSS
I
VCC
VCC
I
I
I
I
I
I
I
I
VSS
I
VCC
VCC
OL
3.5
4.0
4.5
1.5
2.0
KEY0
PRESET ¶ PRESET • PRESET/EDIT
FM/AM
MEMORY
KEY1
6CH INPUT
INPUT ¶
INPUT MODE
SPA
INPUT •
2.5
3.0
TUNING MODE RDS MODE
SPB
EFFECT
EON
PTY SEEK MODE PTY SEEK START
PROGRAM ¶ PROGRAM • A/B/C/D/E
7
6
5
4
3
2
1
B
Cr/Pr
Cb/Pb
Y
Cr/Pr
Cb/Pb
Y
VCR2 /
DVR
VCR2 /
DVR
D-TV /
LD
VCR2 /
DVR
VCR2 /
DVR
D-TV /
LD
13
11
21, 31
25, 35
IC609
IC609
IC701
IC701
■ BLOCK DIAGRAM (1/2)
A
4
7
7, 17
1, 11
IC752
IC752
IC752
IC702
IC603
IC602
C
IC607
IC601
5
7
IC601
3
1
1
7
4
IC751
IC751
IC751
IC610
LC74781-9798
D
15
11
13
IC607
IC607
Q701
Y
Cr/Pr
Cb/Pb
E-32/J-28
VIDEO
• See page E-66/J-62 → SCHEMATIC DIAGRAM
Q609
Q601, 604
E
F
G
H
I
E-33/J-29
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
J
7
6
5
4
3
2
LEVEL CONVERT
&
SIGNAL DETECT
LEVEL CONVERT
&
SIGNAL DETECT
E-34/J-30
(U, C, A only)
VCR2/DVR
L/R
CD-R
L/R
MD/TAPE
L/R
VCR2/DVR
L/R
D-TV/LD
L/R
CD-R
L/R
MD/TAPE
L/R
IC503
IC501
IC511
INPUT
SELECTOR
REC OUT
SELECTOR
IC502, 503
FUNCTION
• See page E-62/J-58 → SCHEMATIC DIAGRAM
D-TV/
LD
DVD
CD-R
CD
DSP
• See page E-64/J-60 → SCHEMATIC DIAGRAM
IC507
3
1
IC506
AK4527
IC514 1/2
IC501
YSS928
IC512
IC512
IC512
IC514
3
1
IC515
3/5
1/7
IC514
5
7
IC512
IC512
IC522
FL/FR
IC512
MAIN
µ-COM
DOLBY
DIGITAL/
DTS
DECODER
IC513
5/3
7/1
4M DRAM
IC502
SOUND FIELD
PROCESSING
/
SPEAKER
CONFIGURATION
/
VIRTUAL
PROCESSING
/
HEADPHONE
PROCESSING
SW
AK4393
IC520
IC522
IC521
3/5
1/7
AK4527
IC514 2/2
D/A
C/SW
D/A
RL/RR
D/A
FL/FR
D/A
L/R
DUTY
CORRECTOR
IC522
■ BLOCK DIAGRAM (2/2)
IC522
1
BASS OUT: MAIN
C
CDR
DIGITAL OUT
INHIBIT 2
IC525
3
1
IC524
5/3
7/1
IC802
IC803
5/3
7/1
Q516, 519
Q803, 804
OPERATION
IC522
SW945~954, 961, 965, 901~905,
SW941~944 (B, G only)
SW964
F
E-35/J-31
MAIN
• See page E-67/J-63 → SCHEMATIC DIAGRAM
SUB WOOFER
IC804
OPERATION
• See page E-63/J-59 → SCHEMATIC DIAGRAM
IC901
(U, C, A only)
FUNCTION
• See page E-62/J-58 → SCHEMATIC DIAGRAM
E
• See page E-65/J-61 → SCHEMATIC DIAGRAM
MD/
TAPE
DIGITAL OUT
INHIBIT 1
D
IC801
B
VR801/802
A
RY1, 2, 151, 152
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
Q515, 517, 518, 520, 521~528
∞
SW903
DC
RY301
IC526
M30802SGP
from MAIN
POWER
• See page E-68/J-64 → SCHEMATIC DIAGRAM
IC527
FLASH ROM
G
LDD Limit
Detect
Limiter
Control
H
D204~207
D351
D352
Q301
Q509, 510, Q545
IC355
IC354
IC353
IC352
IC351
I
D201
D208~212
IC516, 518, 519
IC523
IC528
GY
GY
J
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
■ PIN CONNECTION DIAGRAM
• ICs
AN78N05
NJM7805FA
NJM7812FA
NJM78M05FA
µPC29M33T-E1
NJM79M05FA
NJM79M12FA
PQ025EZ5MZP
3: IN
2: COM
2: COM
3: OUT
3: IN
1: OUT
NJM2068MD
NJM2904M
TK15420M
µPC4570G2
2: IN
1: COM
1
1: OUT
NJM2068LD
NJM4556AL
TC4066BP
5
TC74HC00AF
TC74HCU04AF
TC74VHCT08AF
7
8
7
8
4
14
14
1
1
1
1
TC74HC4051AP
TC74HC4053AP
TC74HCU04AP
CS3310-KS
LA7104M
LA7108M
BU2092
8
LC72722
9
8
16
16
1
1
1
AK4393-VF-E2
LC74781-9798
1
LC78211
LC78213
LC78212
14
15
28
12
24
12
24
18
1
15
30
30
1
1
LA7109
1
AK4527VQ
MSM514260C-60JS
MBM29F400BC-70
33
23
18
25
24
48
1
22
34
36
20
44
1
12
1
11
40
1
LC75710NE
LC75712E
M30802SGP
YSS928
108
48
33
120
73
109
72
121
37
160
81
80
32
49
64
17
1
16
144
1
36
41
1
40
E-60/J-56
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
• Diodes
1N4002S
1SR139
1SS133
1SS270A
1T2
HZS7B2TD
MTZJ4.7C
MTZJ5.1A
MTZJ5.6B
MTZJ6.8A
MTZJ9.1A
MTZJ11B
MTZJ12A
MTZJ12C
MTZJ16A
MTZJ30.0A
Anode
1SS355
RB501V-40
Anode
Cathode
Cathode
D2SBA20
S5VB20
—
~
+
~
—
~
~
+
• Transistors
2SA893A
2SA1015
2SB949
2SC535
2SC1815
2SC1890A
2SC2240
2SC2878
2SB1565
2SD2396
2SA933S
2SC1740S
2SD1915F
2SD1991A
DTA144ES
DTC114ES
DTC144ES
E
E
CB
CB
2SA1708
2SA1770
2SC4488
2SC4614
2SA1037
2SC3326
DTA144EK
DTC144EKA
2SA1492
2SC3856
BC
2SK246
C
E
B
E
E-61/J-57
C
B
S
GD
E
BC
E
9
8
7
6
5
4
3
5
6
2
4
-11.9
11.9
7 0.1
1 0.1
-11.9
4
8
11.9
0.1
1
1
0.1
0.1
7
7
0.1
4
-11.9
8
11.9
Point 3 Pin 20 of IC526
0.1
3
0.1
2
0.1
6
0.1 5
0.1
5
0.1
6
2
0.1
0.1 3
0
0
0
0
0
0
0
0
PHONO EQ
0.1
0.1
0.1
0.1 3 8
MAIN L
0
0
0
0
0
0
0
0
11.9
-11.9
11.9
E-68/J-64
B5
0
0
0
0.1
2
3
5
6
0.1
0.1
0.1
0
2
4
-11.9
8
11.9
11.9
0
0
0
0
0
7
0.1
0.1
1
11.9
0
0
11.9
0
0
0
0
0
0
E-68/J-64
C5
0.7
0.7
0
0
0
0
DIGITAL IN
11.9
0
0
0
-11.9
0
0
11.9
0
0.7
0.7
0
0
0
0
INPUT SELECTOR
11.9
-11.9
0
0
0
0
0
0
0
0
0
0.1
0.1
0
0
0
0
0.1
5
0.1
5
6
0.1
0.1
2
0.1 3
3
2
0.1
0.1
4
-11.9
11.9
1
7
0.1
0.1
7
0.1
0.1
1
1
0.1
0.1
7
2.3
2.3
2.4
1.9
0.1
2.3
2.9
2.4
2.0
2.0
2.8
1.8
+5M1
3.5
3.5
2.9
4.9
0.1
E-68/J-64
B2
4.8
2.0
2.5
2.4
2.6
0
1.4
0
0.8
1.8
2.0
1.7
2.8
2.8
2.0
2.3
2.9
3.0
2.4
2.6
1.5
1.4
2.1
2.1
0
0
4.9
0
4.9
0
4.9
4.9
0.1
1.3
0
1.3
0
1.0
~
0
4.9
4.9
4.8
4.8
4.8
4.8
4.8
4.8
4.8
4.9
1.8
3.0
2.6
1.4
2.1
4.9
4.7
4.8
0
4.8
2.8
2.3
0
0
4.9
4.9
0
4.9
0
4.9
4.9
0
0
0
0
A
0
0
0
0
0
0
4.9
0
0
-5.0
0
6.5
6.5
12.2
7.1
0
0
-0.1
4.9
0
0
-5.0
0
0
0
0
0
0
4.9
0
0
-5.0
0
-0.1
0
0
0
0
0
4.9
4.9
4.9
4.9
ELECTRIC
VOLUME
4.9
0
4.8
POWER
DETECT/RESET
0
0
0
4.9
0
4.9
4.9
4.9
0
0
12.9
13.0
2 1
4.9
4
0
-5.0
-5.0
-5.0
-5.0
-5.0
4.9
-5.0
W504
0
0
0
2
5
6
0 3 4
0
11.9
8
0
0
0
0
-11.9
8
11.9
-11.9 4
0 5
0 6
0
0
0 2
3
0
F
1
7
7
1
0
0
0
0
0
0
0
0
MAIN µ–COM
0
4.8
B
12.9
0
0.6
0.6
5
0
0
2
0 4
0 3
0
5.6
3
5.6
5.6
E-56/J-52
-11.9
11.9
6 8
★ All voltage are measured with a 10M /V DC electric volt meter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
0
4.9
4.9
4.8
REAR L
-11.9
4
11.9
8
-11.9
4
11.9
8
FRONT L
3
2
0.1
6
0.1
0.1
0.1
6
0.1 5
8
FLASH MEMORY
0
0
0
0
0
0
0
0
CENTER
0.1
0
0
0.1
HPF
E1
AXD
4.8
0
1
E-64/J-60
2.4
+5D2
2.5
1.9
2.4
4.8
0
SCHEMATIC DIAGRAM (FUNCTION)
0
4.8
4.8
G2
2.3
E-65/J-61
2.3
2.3
0
4.8
#503
2.4
2.9
4.9
0
0
1
7
0
to OPE (4)
4.9
4.8
0
4.8
2.3
0
0
E
0
4.5
0
4.9
D
2.0
1.8
2.8
2.0
2.0
4.8
4.8
11.9
11.9
0
-11.9
2.9
3.5
3.5
C
4.9
4.9
0
0
0
B
0
2
6
0
0
4.9
0
4.9
4.9
4.9
4.9
4.9
0
0
0
0
4.9
0
0.1
0
0
0
4.7
4.9
4.9
0
4.9
0
0
4.9
4.9
4
-11.9
5.0
0
0
0
0
11.9
-11.9
-5.0
0
0
5.6
5.6 5.6
0
0
0
0
-5.0
A6
1 0
0
7
4.9
11.9
E-65/J-61
5 8
0 3
4.9
G
-11.8
-11.8
-11.8
0
0
4.9
0
3.7
4.9
3.7
4.9
4.9
4.9
4.3
-11.8
4.3
-11.8
-11.8
-11.8
4.3
4.9
-11.8
4.9
4.3
4.9
-11.8
4.9
-11.8
4.9
-11.8
E-68/J-64
F4
4.3
4.4
4.3
4.4
4.4
4.4
-11.8
4.4
-11.8
-11.8
-11.8
-11.8
-11.8
-11.8
B Q510 C
A Q509 E
Point 4 emitter of Q509
and collector of Q510
-11.8
4.9
0
0
0
0
0
0
4.9
0
0
-11.8
0
0
-11.8
0
0
0
-11.8
0
0
0
-11.8
0
0
0
-11.8
-11.8
-11.8
0
0
0
0
0
0
MUTE
H
POWER ON
(Connect the power cord)
s24
s24
C670
s24
C672
C671
I
15
10
9
AGNDL
AGNDR
AINR
MUX
MUX
13
VA-
VA+
–
+
12
8
8
–
+
2
3
4
L2
LCOM1
6
7
8
9
10
11
19
16
12
18
17
L5
L6
LCOM3
LCOM4
VDD
VSS
VEE
RES
S
SHIFT REGISTER
LATCH
LEVEL SHIFTER
VD-
4
8
POWER OFF
(Disconnect the power cord)
A-1
A0 to A17
CE
OE
RESET
BYTE
WE
VSS
VCC
16
DGND
5
24
SDATAI
SDATAO
3
7
RCOM1
R3
R4
RCOM2
R5
R6
RCOM3
R7
28
27
26
25
24
23
22
21
20
14
15
13
R2
29
RY/BY
CE
CL
D1
RCOM4
R1
30
AOUTR
CS
2
SCLK
ZCEN
1
6
MUTE
8
11
AOUTL
14
C670-672
2
5
6
7
8
9
10
11
19
16
12
18
17
LCOM1
L4
L5
LCOM2
L7
LCOM3
VDD
VSS
VEE
RES
S
SHIFT REGISTER
LATCH
LEVEL SHIFTER
10
11
19
16
12
18
17
7
8
9
0.1/16
US13510
STB
Address
Latch
x
2
Standard
Voltage
x
X-Decoder
Y-Decoder
Chip Enable
Output Enable
Logic
1
Starter
Circuit
STB
+
Amp.
–
Excessive Electric
Current Protection
Rsc
SHIFT REGISTER
LATCH
LEVEL SHIFTER
Output Pass Transistor
IC528: AN78N05
Voltage Regulator
LCOM3
VDD
VSS
VEE
RES
S
L8
LCOM2
L7
L6
LCOM1
L5
4
5
6
3
L4
2
L3
1
L2
L1
IC503, IC512: LC78211
Analog Function Switch
L8
L6
3
4
x: NOT USED
O: USED / APPLICABLE
x
1
L2
L3
L1
IC502: LC78212
Analog Function Switch
Erase Voltage
Generator
Timer for
Program/Erase
Program Voltage
Generator
ZZ
ZZ
ZZ
Serial to
Parallel
Register
Low Vcc Detector
Command
Register
State
Control
RY/BY
Buffer
IC527: MBM29F400BC-70
4Mbit Flash Memory
L7
5
L4
LCOM2
L3
1
L1
8
Control
Register
IC522: LC78213
Analog Function Switch
16
E-67/J-63
F4
AINL
IC516, IC518, IC519: CS3310-KS
Stereo Digital Volume Controller
5 +IN2
–VCC 4
+ –
6 –IN2
+ –
7 OUT2
–IN1 2
+IN1 3
8 +VCC
OUT1 1
K
RCOM1
R4
R5
R6
25
24
23
22
R2
R3
R4
29
28
27
26
25
14
15
13
21
20
24
23
22
R1
30
x
E-62/J-58
Cell Matrix
Y-Gating
Data Latch
Input/Output
Buffers
CE
CL
D1
RCOM3
R8
RCOM2
R7
R6
RCOM1
R5
CL
CE
D1
RCOM3
R8
14
15
13
21
20
R3
26
DQ0 to DQ15
3
Heat
Protection
ZZ
ZZ
ZZ
ZZ
ZZ
ZZ
R2
28
27
RCOM2
R7
R1
29
L
30
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
IC501: NJM2068MD
IC506, IC507, IC511, IC513~IC515: µPC4570G2
IC521, IC523~ICIC525: µPC4570G2
Dual OP-Amp
J
CONTROL
A
1.3
0
2.0
2.8
2.1
1.5
2.4
2.9
4.9
0
0.1
~
0
0
0
0
0
2.2
4.8
470/25
4.9
0.1
0
4.9
4.6
0
1.4
0
0
0
0.047/5.5
0
0
E-66/J-62
F4
E-67/J-63
F4
E-65/J-61
G3
E-68/J-64
H6
E-66/J-62
E5
E-63/J-59
H1
Power Supply
CONTROL
CONTROL
B
A
C
D
E
F
G
H
I
J
K
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
SCHEMATIC DIAGRAM (OPERATION 2/2)
1
IC801: TC4066BP
Quad Analog Switch/Multiplexer
5.0
4.1
4.0
IN/OUT1 1
14 VDD
OUT/IN1 2
13 CONT1
OUT/IN2 3
12 CONT4
IN/OUT2 4
11 IN/OUT4
CONT2 5
10 OUT/IN4
CONT3 6
9 OUT/IN3
VSS 7
8 IN/OUT3
4.0
4.1
4.1
0
0
5.0
2
to FUNC (1)
3
7
8
–IN2
+Vcc
–IN1
6
IC804: NJM4556AL
Dual OP-Amp
V+
8
2, 6
–INPUT
+INPUT
3, 5
C983
+IN2
+IN1
2 3 4 5
–Vcc
1
OUT2
IC802, IC803: NJM2068LD
Dual OP-Amp
OUT1
E-62/J-58
I5
C985
C982
PHI
E-62/J-58
F1
CB974
OUTPUT
1, 7
R982
1K
R983
1K
V–
4
HSS104
HSS104
&3
D973
&3
D972
C980
1000P
D971
BASS EXTENSION
MTZJ9.1A
4
TONE CONTROL
5
47/16
47/16
9.4
11.1
11.1
0
0
0
0
0
0
0
8.4
8.4
8.7
HP
MUTE
8.7
0
0
0
0
0
8.4
0
E-62/J-58
G1
0
8.4
0
0
0.7
0
8.4
0
0
to FUNC (1)
6
8.4
4.8
0
0
0
0
0.7
8.4
-8.3
0
FRONT L
0
0
-8.3
0
0
0
8.4
0
-8.7
0
0
0
0
0
-11.1
-11.1
7
8
9
★ All voltage are measured with a 10M /V DC electric volt meter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
E-65/J-61
L
B
A
C
D
E
F
G
H
I
J
K
L
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
SCHEMATIC DIAGRAM (VIDEO)
IC601: TK15420M
Video Amp
IC602, IC603, IC702: TC74HC4051AP
Analog Multiplexer/Demultiplexer
1
OUT A
1
8 VCC
E-66/J-62
–IN A
2
+IN A
3
6 –IN B
VEE
4
5 +IN B
+ –
7 OUT B
+ –
3.2
3.1
4.9
0
0
0
-4.8
0
0
1.0
4.9
0
D5
46.6
46.5
47.1
46.6
4.9
4.9
0
-4.8
0
0
0
0
IC607, IC752: TC74HC4053AP
Analog Multiplexer/Demultiplexer
25.4
46.1
C265
s19
0
0
0
0
0
Y SELECTOR
45.8
45.2
0
0
0
0
46.4
16
B
10
C
9
IC608: TC74HCU04AP
Hex Inverters
LEVEL
CONVERTER
INPUT STATES
"ON" CHANNNEL (S)
INHIBIT C B A
0 0 0
0X, 0Y, 0Z
0
0 0 1
1X, 0Y, 0Z
0
0 1 0
0X, 1Y, 0Z
0
0 1 1
1X, 1Y, 0Z
0
1 0 0
0X, 0Y, 1Z
0
1 0 1
1X, 0Y, 1Z
0
1 1 0
0X, 1Y, 1Z
0
1 1 1
1X, 1Y, 1Z
0
X X X
NONE
1
BINARY TO 1-OF-8
DECODER WITH INHIBIT
8
VEE
7
0X
12
1X
13
0Y
2
1Y
1
0Z
5
1Z
3
SW
14
X-COM
15
Y-COM
4
Z-COM
SW
SW
SW
0
0
0
-0.6
Cb SELECTOR
0
VDD
6
22P/630
0
45.1
0
0
11
1.0
-4.9
-0.1
A
VSS
s20
4.9
0
0
C722
0.1/16
-4.9
0
0
1.0
R721
C713
C721
0
100/16
0
0
INHIBIT
0
0
4.9
4.9
3
9
-4.8
0
0
C266
0
0
0
0
0
0
0
0
2200/6.3
INPUT SELECTOR
2
-0.6
SW
SW
0
1A 1
14 VDD
1Y 2
13 6A
2A 3
12 6Y
2Y 4
11 5A
3A 5
10 5Y
3Y 6
9 4A
VSS 7
8 4Y
3.2
Cr SELECTOR
0
-0.1
0
0
0
3.1
0
0
0
IC610: LC74781-9798
On Screen Display Controller
0
0
s20
CS 9
Serial
SIN 11
45.6
45.2
parallel
converter
SCLK 10
8-bits
latch
+
command
decoder
1.0
22P/630
4.9
0
0
Vertical
character
size
register
Horizontal
display
position
register
Vertical
display
position
register
Blinking
and inversion
control
register
Horizontal
size
counter
Vertical
size
counter
Horizontal
dot
counter
Vertical
dot
counter
Blinking
and inversion
control
circuit
Blinking
and inversion
control
register
Blinking
and inversion
control
register
Character
control
counter
Line
control
counter
RAM
write
adress
counter
Display
control
register
0
0
RST 23
0
-0.6
4.9
0
-0.6
Decoder
1.0
0.4
Horizontal
character
size
register
46.0
45.2
Display
RAM
VDD1 24
4
VSS1 1
FRONT L
VDD2 12
46.1
E-66/J-62
C1
45.1
E-62/J-58
I6
CHARA 8
1.0
-11.9
0
1.0
0
1.0
0
1.0
0
1.0
0
1.0
45.7
46.5
0
45.1
0
0
-0.6
-0.6
CENTER
REAR L
5
E-67/J-63
A5
E-62/J-58
I3
45.1
Horizontal
character
size
register
OSCIN 6
OSCOUT 7
Font
RAM
Timing generator
SYNIN 17
Horizontal
character
size
register
SEPC 18
SEPOUT 19
Horizontal
character
size
register
4
CTRL1
45.0
0
IC609: LA7109
75 Video Driver
0
1.0
45.0
4.9
0
4.8
0
0
1.0
0
4.9
-4.8
0
0
0
2.6
2.6
2.6
2.6
2.6
45.0
0
2.6
0
-0.6
4.9
4.5
1.0
1.6
0
0
1.6
0
-4.8
13
CVOUT
0
4.9
-4.8
0
0
0
0
0
4.5
4.9
0
4.5
0
4.9
0
0
4.5
2
3
VIN2+
4
6dB
6dB
4.3
4.3
4.9
0
NFB1
MUTE1
0 0
4.8
DR
35
VOUT1
34
GND
33
VOUT2
DR
NFB2
5
32
DR CTL2
-VCC1
6
31
VOUT3
VIN3+
7
NFB3
0
0
45.2
IC701: LA7108M
Video Amp
36
46.1
30
MUTE4
8
29
-VCC4
N.C.
9
28
N.C.
N.C.
10
27
N.C.
VIN4+
11
26
+VCC2
NFB4
12
25
VOUT4
6dB
DR
Vss
1
DATA
2
CLOCK
3
LCK
4
Q0
5
Q1
6
Q2
7
Q3
8
Q4
9
Control
Circuit
18
VDD
17
OE
16
Q11
15
Q10
14
Q9
13
Q8
12
Q7
11
Q6
10
Q5
VIN1+
1
NFB1
2
MUTE1
3
VIN2+
4
6dB
6dB
DR
16
+VCC
15
VOUT1
14
GND
13
VOUT2
DR
NFB2
5
12
MUTE2
-VCC1
6
11
VOUT3
VIN3+
7
10
MUTE3
NFB3
8
9
-VCC2
1.0
4.8
4.9
-0.1
4.3
45.2
0
3.1
-4.7
-4.7
-4.7
-0.9
0
0.8
0
0
3.1
3.1
0
-0.5
0.8
0
0.8
4.3
-0.1
4.9
4.8
-0.6
-0.6
0
-0.1
-0.6
0
4.8
-0.1
14
NFB5
15
-VCC2
16
VIN6+
17
NFB6
18
6dB
24
GND
23
VOUT5
22
DR CTL1
21
VOUT6
20
MUTE3
19
-VCC3
VIN1+
1
16
+VCC
NFB1
2
15
VOUT1
MUTE1
3
14
GND
VIN2+
4
13
VOUT2
NFB2
5
12
DR CTL
-VCC1
6
11
VOUT3
VIN3+
7
10
MUTE2
NFB3
8
9
-VCC2
6dB
DR
6dB
DR
DR
DR
6dB
6dB
DR
DR
0
4.9
0
4.8
0
4.9
2.4
2.5
0
1.0
4.9
1.7
0.7
13
VIN5+
2.5
1.0
2.3
1.7
1.0
0
ON
SCREEN
4.9
0
-0.7
DR
1.7
0
2.0
2.0
4.9
0.9
0
4.9
0
4.9
4.9
4.9
-11.9
4.9
0.4
6dB
6dB
1
1.0
MUTE2
0
3.1
-4.7
7
4.9
IC751: LA7104M
Video Amp
-0.5
4.8
0
0
0
0
-0.6
0.2
-1.6
0
0
-4.7
-4.7
0
0
3.1
46.6
0
0
0
4.9
0
0
0
3.1
4.9
0
0
-4.7
0
0
15
CVIN
+VCC1
1
4.8
4.9
1.0
0
Y-INPUT
SELECTOR
5
BLANK
IC611: BU2092
Serial In/Parallel Out Driver
VIN1+
-0.6
0
0
0
3
Latch
0
0
0
0
0
0
0
2
12 Bit Shift Register
0
0
21
CTRL2 XtalIN XtalOUT
Output Buffer (Open Drain)
4.9
0
0
0
Shift
register
1.0
4.9
6
Synchronization
signal generator
CTRL3 22
45.7
0
0
0
0
Character output control
Background control
Video output control
SEPIN 20
C-INPUT
SELECTOR
0
Decoder
Horizontal
character
size
register
0
Point 1 Pin 3 of IC610
8
★ All voltage are measured with a 10M /V DC electric volt meter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
R268, 275, 282
9
19
C266
20
R254, 261
2200/6.3
UR81922
2200/6.3
UR81922
2200/6.3
UR81922
270
HC65527
2200/6.3
UR81922
270
HC65527
E-66/J-62
B
A
C
D
E
F
G
H
I
J
K
L
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
SCHEMATIC DIAGRAM (MAIN)
FRONT L POWER AMP
1
46.5
46.5
46.2
46.5
1.0
0.5
1.0
0
0.5
36.5
46.2
0
-0.4
24.2
0
-1.0
0
12.2
36.1
0.1
36.8
0.1
0.7
2
36.8
0
0
0
-0.5
0
-0.5
-1.0
-1.0
-46.5
0
-46.5
-45.3
0
0
0
FRONT R POWER AMP
0.3
0.3
46.5
46.5
1.0
1.0
0.5
0.5
3
0
46.2
0
-0.4
0
-1.0
0
0
-11.8
0
0
0
-0.5
-0.5
0
-11.8
-1.0
-1.0
-46.5
0
-46.5
0.2
0
0
REAR L
-11.8
0.4
0
4.8
46.5
0.4
-36.1
0
0.3
46.5
1.0
1.0
0.5
-28.6
0.5
4.8
-29.2
46.2
-0.4
E-62/J-58
I4
4
0
0.4
REAR L POWER AMP
FRONT L
E-62/J-58
I2
-45.3
13.0
4.7
0.1
0
0
1.3
-29.2
-1.0
0
0.7
0
0
-11.9
-28.6
0
0
E-66/J-62
H5
1.0
0
1.0
0
-0.5
-0.5
0
1.0
-1.0
-1.0
-46.5
0
0
1.0
5
0
0
-46.5
1.0
-45.3
46.0
0.3
46.5
0
0
REAR R POWER AMP
0
AC 59.9
46.5
1.0
AC 73.7
-46.5
46.4
0.3
46.5
1.0
0
0
0.5
0.5
46.2
0
-0.4
0
-1.0
0.3
0
0
6
36.7
-0.5
-1.0
0
0
0
-46.5
-37.4
CENTER POWER AMP
CENTER
24.6
12.3
0
12.2
0.1
0
46.5
13.0
6.6
0
6.6
0
6.6
0.5
46.2
-0.4
0
470/25
0.5
0
-1.0
0
36.7
-37.4
6.6
13.0
10/100
UR89710
E-68/J-64
F2
46.5
1.0
to POWER (1)
24.3
1.0
7
0
-37.4
0
-46.5
-45.3
0
36.7
-0.5
-1.0
0
-0.5
-0.5
-46.5
-1.0
-1.0
x: NOT USED
O: USED / APPLICABLE
0
-45.4
-46.2
-45.4
-45.7
-46.5
-46.2
-24.1
8
-36.3
0.1
0
0
0
-46.5
-46.5
0.1
-46.5
-36.2
-36.3
-37.2
★ All voltage are measured with a 10M /V DC electric volt meter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
9
E-67/J-63
B
A
C
D
E
F
G
H
I
J
K
L
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
SCHEMATIC DIAGRAM (POWER)
1
POWER RELAY
E-67/J-63
I7
AC
13.2
13.1
0
0
0.7
0
E-62/J-58
D8
2
E-62/J-58
H8
3
4
VOLTAGE SELECTOR
240V
1-2/5-6
220V
2-3/6-7
110V
3-4/7-8
120V
4-5/8-1
E-62/J-58
C8
E-62/J-58
C8
REGULATOR
5
17.1
12.0
0
17.7
0
0
0
-17.3
-12.0
-17.7
E-66/J-62
I6
AC
29.4
AC
16.3
5.0
8.6
5.0
8.4
6
0
9.2
0
-0.1
-0.1
-9.7
0
-9.2
-4.8
x: NOT USED
O: USED / APPLICABLE
7
FL OUT
C IN
IC351: NJM7812FA
IC353: NJM7805FA
Voltage Regulator
VREF
IC1: LC72722
RDS Decoder
1
5
6
VDDA 3
+
PLL
(57kHz)
REFERENCE
VOLTAGE
VSSA 4
20
21
22
23
T1 7
T2 8
T3 9
T4 10
9
ANTIALIASING
FILTER
CCB
TEST
57kHz
bpf
(SCF)
DATA
DECODER
SMOOTHING
FILTER
RAM
(24 BLOCK DATA)
MEMORY
CONTROL
ERROR CORRECTION
(SOFT DECISION)
INPUT
COMMON
VIN
SYNC/EC
CONTROLLER
19 RDS-ID
OUTPUT
OUTPUT
VOUT
18 SYNC
24 SYR
★ All voltage are measured with a 10M /V DC electric volt meter.
★ Components having special characteristics are marked s and must be replaced
with parts having specifications equal to those originally installed.
★ Schematic diagram is subject to change without notice.
CLK(4.332MHz)
OSC/DIVIDER
SYNC
DETECT-1
SYNC
DETECT-2
INPUT
COMMON
11 16 17
13
12
X OUT
DO
CL
DI
CE
X IN
MPX IN 2
14 VDDD
15 VSSD
VREF
T5
T6
T7
8
CLOCK
RECOVERY
(1187.5Hz)
IC354: NJM78M05FA
Voltage Regulator
IC352: NJM79M12FA
IC355: NJM79M05FA
Voltage Regulator
GND
E-68/J-64
PARTS LIST
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
■ WARNING
RX-V800/RX-V800RDS/HTR-5280
Components having special characteristics are marked s and must be
replaced with parts having specifications equal to those originally installed.
PARTS List. For the parts No. of the carbon resistors, refer to last page.
● Carbon resistors (1/6W or 1/4W) are not included in the ELECTRICAL
CHIP ALUMI.ELECTROLYTIC CAP
CERAMIC CAP
CERAMIC CAP ARRAY
CHIP CERAMIC CAP
MULTILAYER CERAMIC CAP
CHIP MULTILAYER CERAMIC CAP
RECOGNIZED CERAMIC CAP
CERAMIC TUBULAR CAP
SEMI CONDUCTIVE CERAMIC CAP
ELECTROLYTIC CAP
MICA CAP
MULTILAYER FILM CAP
METALLIZED PAPER CAP
MYLAR FILM CAP
MULTILAYER MYLAR FILM CAP
PAPER CAPACITOR
POLYSTYRENE FILM CAP
POLYESTER FILM CAP
POLYETHYLENE FILM CAP
POLYPROPYLENE FILM CAP
TANTALUM CAP
CHIP TANTALUM CAP
TRIMMER CAP
CONNECTOR
CONNECTOR,BASE PIN
CONNECTOR,CANNON
CONNECTOR,DIN
CONNECTOR,FLAT CABLE
CONNECTOR,BASE POST
COIL,AM MIX
COIL,FM ANTENNA
COIL,FM DETECT
COIL,FM MIX
OUTPUT COIL
DIODE ARRAY
DIODE BRIDGE
CHIP DIODE
VARACTOR DIODE
CHIP ZENER DIODE
ZENER DIODE
CERAMIC DISCRIMINATOR
FERRITE BEADS
FERRITE CORE
CHIP FET
FLUORESCENT DISPLAY
CERAMIC FILTER
COMB FILTER MODULE
LC FILTER,EMI
GROUND PLATE
GROUND TERMINAL
FUSE HOLDER
IC PROTECTOR
JUMPER CONNECTOR
JUMPER,TEST POINT
LIGHT DETECTING MODULE
L.EMIT
LED.DSPLY
LED.INFRD
MODUL.RF
PHOT.CPL
PHOT.INTR
PHOT.RFLCT
PIN.TEST
PLST.RIVET
R.ARRAY
R.CAR.
R.CAR.CHP
R.CAR.FP
R.FUS
R.MTL.CHP
R.MTL.FLM
R.MTL.OXD
R.MTL.PLAT
RSNR.CE
RSNR.CRYS
R.TW.CEM
R.WW
SCR.BND.HD
SCR.BW.HD
SCR.CUP
SCR.TERM
SCR.TR
SUPRT.PCB
SURG.PRTCT
SW.TACT
SW.LEAF
SW.LEVER
SW.MICRO
SW.PUSH
SW.RT.ENC
SW.RT.MTR
SW.RT
SW.SLIDE
TERM.SP
TERM.WRAP
THRMST.CHP
TR.CHP
TR.DGT
TR.DGT.CHP
TRANS
TRANS.PULS
TRANS.PWR
TUNER.AM
TUNER.FM
TUNER.PK
VR
VR.MTR
VR.SW
VR.SLIDE
VR.TRIM
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
LIGHT EMITTING MODULE
LED DISPLAY
LED,INFRARED
MODULATOR,RF
PHOTO COUPLER
PHOTO INTERRUPTER
PHOTO REFLECTOR
PIN,TEST POINT
PLASTIC RIVET
RESISTOR ARRAY
CARBON RESISTOR
CHIPRESISTOR
FLAME PROOF CARBON RESISTOR
FUSABLE RESISTOR
CHIP METAL FILM RESISTOR
METAL FILM RESISTOR
METAL OXIDE FILM RESISTOR
METAL PLATE RESISTOR
CERAMIC RESONATOR
CRYSTAL RESONATOR
TWIN CEMENT FIXED RESISTOR
WIRE WOUND RESISTOR
BIND HEAD B-TITE SCREW
BW HEAD TAPPING SCREW
CUP TITE SCREW
SCREW TERMINAL
SCREW,TRANSISTOR
SUPPORT,P.C.B.
SURGE PROTECTOR
TACT SWITCH
LEAF SWITCH
LEVER SWITCH
MICRO SWITCH
PUSH SWITCH
ROTARY ENCODER
ROTARY SWITCH WITH MOTOR
ROTARY SWITCH
SLIDE SWITCH
SPEAKER TERMINAL
WRAPPING TERMINAL
CHIP THERMISTOR
CHIP TRANSISTOR
DIGITAL TRANSISTOR
CHIP DIGITAL TRANSISTOR
TRANSFORMER
PULSE TRANSFORMER
POWER TRANSFORMER ASS’Y
TUNER PACK,AM
TUNER PACK,FM
FRONT-ENDTUNER PACK
ROTARY POTENTIOMETER
POTENTIOMETER WITH MOTOR
POTENTIOMETER WITH ROTARY SW
SLIDE POTENTIOMETER
TRIMMER POTENTIOMETER
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:
■ ELECTRICAL PARTS
C.A.EL.CHP
C.CE
C.CE.ARRAY
C.CE.CHP
C.CE.ML
C.CE.M.CHP
C.CE.SAFTY
C.CE.TUBLR
C.CE.SMI
C.EL
C.MICA
C.ML.FLM
C.MP
C.MYLAR
C.MYLAR.ML
C.PAPER
C.PLS
C.POL
C.POLY
C.PP
C.TNTL
C.TNTL.CHP
C.TRIM
CN
CN.BS.PIN
CN.CANNON
CN.DIN
CN.FLAT
CN.POST
COIL.MX.AM
COIL.AT.FM
COIL.DT.FM
COIL.MX.FM
COIL,OUTPT
DIOD.ARRAY
DIODE.BRG
DIODE.CHP
DIODE.VAR
DIOD.Z.CHP
DIODE.ZENR
DSCR.CE
FER.BEAD
FER.CORE
FET.CHP
FL.DSPLY
FLTR.CE
FLTR.COMB
FLTR.LC.RF
GND.MTL
GND.TERM
HOLDER.FUS
IC.PRTCT
JUMPER.CN
JUMPER.TST
L.DTCT
Note) Those parts marked with “#” are not included in the P.C.B. ass’y.
69
A
B
C
D
E
F
G
H
I
J
RX-V800/RX-V800RDS/HTR-5280
1
■ EXPLODED VIEW
172
202
169
171
204
203
101
113
172
174
200
139
2
161
3-11
200-1
174
(6)
2-56
2-1 (3)
145
16
3-21
6
3-22
2-1 (1)
R,B,G,T models
2-21
146
3
R,B,G,T models
2-57
167
171
135
3-25
2-52
2-56
2-55
4
2-57
2-57
2-26
2-22
2-55
2-38
2-36
2-58
2-37
2-34
5
2-34
2-36
2-32
2-57
172
136
2-55
2-59
165
(2)
(4)
6
3-1
(4)
6
117
U,C
models
148
175
(5) 6
115
172
103
6
(10)
25 25
11
147
31
27
27
172
7
161
31
161
167
8
118
140
102
141
1-5
119 U,C models
109
161
172
136
116
172
144
161
110
120
132
133
(7)
6
111
112
136
1-7
170
30
172
172
172
(2)
161
140
137
1-6
1-1
7
(1)
3-1 (3)
172
6
6
2-1
161
143
(9)
6
1-4
3-1
(8)
28
2-37
2-55
161
3-1
(1) 9
167
14
2-31
161
(5)
(7)
2-56
2-28
6
172
2-1
2-29
(3) 9
21
2-57
2-57
2-30
2-1
(5)
2-27
2-12
2-33
142
2-11
2-55
2-54
168
2-13
2-25
2-40
161
161
172
2-1 (2)
161
9 (2)
26
2-57
166
3-1 (1)
29
2-60
114
161
3-31
2-52
2-41
172
164
3-33
136
R,T only
17
166
136
120
166
81
82
Value
1.0
1.8
2.2
3.3
4.7
5.6
10
15
22
27
33
39
47
56
68
75
82
91
100
110
120
150
160
180
200
220
270
330
390
430
470
510
560
680
820
910
1.0 k
1.2 k
1.5 k
1.8 k
2.0 k
2.2 k
2.4 k
2.7 k
3.0 k
3.3 k
3.6 k
3.9 k
4.7 k
5.1 k
5.6 k
6.8 k
8.2 k
9.1 k
❊ : Not available
Value
10 k
11 k
12 k
13 k
15 k
18 k
22 k
24 k
27 k
30 k
33 k
36 k
39 k
47 k
51 k
56 k
62 k
68 k
82 k
91 k
100 k
110 k
120 k
150 k
180 k
220 k
270 k
300 k
330 k
390 k
470 k
560 k
680 k
820 k
1.0 M
1.2 M
1.5 M
1.8 M
2.2 M
3.3 M
3.9 M
4.7 M
RX-V800/RX-V800RDS/HTR-5280
HJ35
HJ35
1/4W Type
HJ35
10mm
HF85
5mm
1/6W Type
HF45
1/4W Type
1/4W Type Part No. 1/6W Type Part No.
HF45 7100
HF45 7100
HF45 7110
HF45 7110
HJ35 7120
HF85 7120
HF45 7130
HF45 7130
HF45 7150
HF45 7150
HF45 7180
HF45 7180
HF45 7220
HF45 7220
HF45 7240
HF45 7240
HJ35 7270
HF85 7270
HF45 7300
HF45 7300
HF45 7330
HF45 7330
HF45 7360
HF45 7360
HF45 7390
HF45 7390
HF45 7470
HF45 7470
HF45 7510
HF45 7510
HF45 7560
HF45 7560
HF45 7620
HF45 7620
HF45 7680
HF45 7680
HF45 7820
HF45 7820
HF45 7910
HF45 7910
HF45 8100
HF45 8100
HF45 8110
HF45 8110
HF45 8120
HF45 8120
HF45 8150
HF45 8150
HF45 8180
HF45 8180
HJ35 8220
HF85 8220
HF45 8270
HF45 8270
HF45 8300
HF45 8300
HF45 8330
HF45 8330
HJ35 8390
HF85 8390
HF45 8470
HF45 8470
HJ35 8560
HF85 8560
HJ35 8680
HF85 8680
HJ35 8820
HF85 8820
HF45 9100
HF45 9100
HJ35 9120
❊
HJ35 9150
HF85 9150
HJ35 9180
HF85 9180
HJ35 9220
HF85 9220
HJ35 9330
HF85 9330
9390
❊
9470
HF85 9470
Parts List for Carbon Resistors
1/4W Type Part No. 1/6W Type Part No.
HJ35 3100
HF85 3100
HJ35 3180
❊
HJ35 3220
HF85 3220
HJ35 3330
HF85 3330
HJ35 3470
HF85 3470
HJ35 3560
HF85 3560
HF45 4100
HF45 4100
HJ35 4150
HF85 4150
HF45 4220
HF45 4220
HJ35 4270
HF85 4270
HF45 4330
HF45 4330
HJ35 4470
HF85 4390
HF45 4470
HF45 4470
HF45 4560
HF45 4560
HF45 4680
HF45 4680
HF45 4750
HF45 4750
HF45 4820
HF45 4820
HF45 4910
HF45 4910
HF45 5100
HF45 5100
HJ35 5110
HF85 5110
HF45 5120
HF45 5120
HF45 5150
HF45 5150
HJ35 5160
❊
HF45 5180
HF45 5180
HF45 5200
HF45 5200
HF45 5220
HF45 5220
HF45 5270
HF45 5270
HF45 5330
HF45 5330
HF45 5390
HF45 5390
HF45 5430
HF45 5430
HF45 5470
HF45 5470
HF45 5510
HF45 5510
HF45 5560
HF45 5560
HF45 5680
HF45 5680
HF45 5820
HF45 5820
HF45 5910
HF45 5910
HF45 6100
HF45 6100
HF45 6120
HF45 6120
HF45 6150
HF45 6150
HF45 6180
HF45 6180
HJ35 6200
HF85 6200
HF45 6220
HF45 6220
HJ35 6240
HF85 6240
HF45 6270
HF45 6270
HF45 6300
HF45 6300
HF45 6330
HF45 6330
HJ35 6360
HF85 6360
HF45 6390
HF45 6390
HF45 6470
HF45 6470
HF45 6510
HF45 6510
HF45 6560
HF45 6560
HF45 6680
HF45 6680
6820
HF45 6820
6910
HF45 6910
HF45
HF45
87
88
1
40
VDD
55 AVDD
Q1
C1
C12
C2
U1
R15
P15/ANI5
52
P14/ANI4
P13/ANI3
P12/ANI2
P11/ANI1
P10/ANI0
P46/AD6
P47/AD7
P17/ANI7
51
50
49
48
47
16
17
54
P57/A15
26
P37
P35/BUZ
P35/PCL
P34/TI2
P33/TI1
8
7
6
5
4
P56/A14
P55/A13
P54/A12
P53/A11
P52/A10
P51/A9
P50/A8
25
23
22
21
20
19
18
P40/AD0
P41/AD1
P42/AD2
P43/AD3
P44/AD4
P45/AD5
10
11
12
13
14
15
P64/RD
P65/WR
P55/WAIT
31
32
33
J1
BATT
9 VSS
24 VSS
C3
42
X1
OPTION
X1
C4
VBAT
41
VDD
OPTION
C5
R3
56
46
AVREF
AVSS
R1
RESET
Q3
Q2
C6
R4
59 P22/SCK1
57
P20/SI1
VBAT
R9
C7
P01/INTP1
36
P00/TI0
R12
R14
Q5
C8
R11
OPTION
C9
C10
P30/TO0
P31/TO1
4
2 DSP/TUN
1 TV
10 VCR
3
S1
AMP/TUN 7
K41
K42
K43
K44
K45
K46
PLAY
K33
VOLK34
SLEEP
K35
TV VOLK36
MUTE
K37
VOL+
K38
TV INPUT
K25
STAND BY
K26
TV POWER
K27
TV VOL+
K28
DIR A
K29
AMP POWER
K30
AV POWER
K17
REC
K18
FF
K19
PAU
K20
REW
K21
STOP
K22
DISPLAY
K9
0
K10
DIR B
K11
>10
K12
CHK13
ENTER
K14
CH+
K1
DSP
K2
9
K3
8
K4
7
K5
6
K6
4
2
3
1
5
INPUT
P55
P54
P53
P52
P51
P50
P40
P41
P42
P43
P44
P45
9 CBL/SAT
8 CD
VBAT
D3
1
2
R17
R18
P62
29
P61
28
P60
27
P57/ASTB
P21/SO1
P23/STB
P24/BUSY
P25/SI0
P26/SO0/SB1
P27/SCK0
54
58
60
61
62
63
64
P32/TO2
R13
30
3
VDD
VBAT
D
Q6
R10
VSS
38
P02/INTP2
39 P03/INTP3
VDD
D1
C11
DVD/MENU 4
DVD/LD 5
TAPE/MD 6
D2
R8
8
JL1
VBAT
37
5
SDA
7
NC
1
2 A0
3 A1
A2
X2
43 IC
45 P04/XT1
44 XT2
R2
J1
VDD
SCL
C
53
6
B
P16/ANI6
R16
A
U1
VDD
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
VDD
■ REMOTE CONTROL TRANSMITTER
● SCHEMATIC DIAGRAM
VDD
2
VDD
3
4
5
6
7
VDD
VBAT
D4
R19
R20
R21
OPTION
Q7
P63
E
Function Keychart
NO
DSP
INPUT
DSP/TUN
TV
1
DSP
VCR
CABLE/SAT
CD
AMP/TUNER
TAPE/MD
DVD MENU
DVD/LD
DSP/TUNER
Shift DSP PROGRAM
2
INPUT
3
1
CH1
CH1
CH1
1
CD
1
1
1
HALL
P1
4
2
CH2
CH2
CH2
2
TUNER
2
2
2
CHURCH
P2
Shift INPUT SELECT
0023
5
3
CH3
CH3
CH3
3
MD/TAPE
3
3
3
JAZZ
P3
6
4
CH4
CH4
CH4
4
DVD
4
4
4
ROCK
P4
7
5
CH5
CH5
CH5
5
D-TV/LD
5
5
5
ENTERTAINMENT
P5
8
6
CH6
CH6
CH6
6
VCR1
6
6
6
TV SPORTS
P6
HALL
CD
CHURCH
TUNER
JAZZ
MD/TAPE
9
7
CH7
CH7
CH7
7
CD-R
7
7
7
MONO MOVIE
P7
1
2
3
10
8
CH8
CH8
CH8
8
CBL/SAT
8
8
8
MOVIE THTR1
P8
ROCK
DVD
ENTERTAINMENT
D-TV/LD
TV SPORTS
VCR 1
-
4
5
6
MONO MOVIE
CD-R
1-MOVIE THTR-2
CBL/SAT VCR 2/DVR
7
8
9
y y/DTS SUR.
PHONO
6.1/ES
6CH INPUT
EFFECT
V-AUX
0
ENTER
>10
CH9
CH9
CH9
9
VCR2/DVR
9
9
9
MOVIE THTR2
CH0
CH0
CH0
0
PHONO
0
0
0
DD/dfs SUR
-
13
ENTER
CH Enter/Recall
CH Enter/Recall
CH Enter
INDEX
6CH INPUT
-
INDEX
INDEX
6.1/ES
-
+10
14
>10
_/_ _
_/_ _
_/_ _
+10
V AUX
+10
15
CH+
TV CH+
VCR CH+
CBL/SAT CH+
DISC+
PRESET+
-
TV CH-
VCR CH-
CBL/SAT CH-
DISC-
PRESET-
-
-
-
TEST
REC/PAUSE
RETURN
-
TEST
<-
DISPLAY/GUIDE
DISPLAY
A/B/C/D/E
DISPLAY/A-B
DISPLAY
DISPLAY
A/B/C/D/E
<-
Up
PAUSE
Up
PAUSE
Up
PAUSE
Up
<-
Left
SKIP-
Left
SKIP-/DIR A
Left
SKIP/CHAP-
Left
<-
Menu Select
PLAY
ON SCREEN
PLAY
Select
PLAY
ON SCREEN
<-
Right
SKIP+
Right
SKIP+/DIR B
Right
SKIP/CHAP+
Right
<-
16
CHREC
CH
18
DISPLAY
19
PAUSE
DISPLAY
20
SKIP-
-
DISC SKIP
PRESET
VCR REC
9
0
17
INDEX
CH
11
12
VCR REC
DISPLAY
DISPLAY
VCR PAUSE
-
+10
DISC+
DISC-
EFFECT
-
PRESET+
<-
PRESET-
<-
A/B
21
PLAY
VCR PLAY
A/B/C/D/E
22
SKIP+
-
23
STOP
VCR STOP
Down
STOP
Down
STOP
Down
STOP
Down
<-
DIR B
24
REW
VCR REW
RECALL
REW
TIME/LEVEL
REW
TITLE
REW
TIME/LEVEL
<-
25
FF
VCR FF
MENU
FF
SET MENU
FF
MENU
FF
SET MENU
<-
MENU
26
AV POWER
VCR POWER
CBL/SAT POWER
CD POWER
-
TAPE/MD POWER
-
<-
27
TV POWER
TV POWER
COD
DIR A
E SET
SELECT
ON
SCREEN
TITLE
LEVEL
POWER
28
STANDBY
STANDBY(OFF)
29
POWER
AMP POWER
POWER
30
TV VOL+
TV VOL+
I
31
TV VOL-
TV VOL-
32
TV INPUT
TV INPUT
SET MENU
AV
POWER
STANDBY
TV
INPUT
TV
TV VOL
SLEEP
MUTE
-
33
SLEEP
TV SLEEP
34
MUTE
TV MUTE
35
VOL+
36
VOL-
DVD/LD POWER
SLEEP
MUTE
VOLUME
VOL+
VOLCABLE/SAT
TUNER
TAPE
DVD/LD
TUNER
TV
VCR
SAT/SAT
CD
0023
MD
(DVD)
LD
0023
Device
x
x
AUX
x
x
x
AUX
x
x
Default
0101
0002
0006
0005(Yamaha)
0003(AMP)
0004(Yamaha)
Library
Change
0008(Yamaha)
0013(DSP)
RX-V800/RX-V800RDS/HTR-5280/DSP-AX8
/
TEST
89