Download Windsor ADM8IB Operating instructions

CARPET EXTRACTOR
Operating Instructions (GB/USA)
Manuel d’utilisation (FRE)
Bedienungsanleitung (GER)
MODEL:
ADM8IA
ADM8IB
ADM8IE
ADM8IS
COUNTRY
AUSTRALIA
BRITIAN
EUROPE
SWITZERLAND
IPX4
Read these instructions before operating the machine
Lire ce manuel avant d’utiliser la machine
Bitte lesen Sie diese Anleitungen, bevor Sie die Maschine in Gebrauch nehmen
AN
86038270 07/14/14
PRV NO. 98655
TABLE OF CONTENTS
Data Log/Table of Contents .............. 1
Maintenance ..................................... 15-17
Safety Instructions ............................ 2
Technical Specifications ................... 18
Controls ............................................ 3-5
Parts Lists ......................................... 19-34
Operations ........................................ 6-11
Spare Parts/Notes ............................ 35
Troubleshooting ................................ 12
EC Declaration of Conformity ........... 36
Blank Page ....................................... 13
Wiring Diagram ................................. 14
INSPECTION
Carefully unpack and inspect your machine for shipping damage. Each unit is operated and thoroughly inspected
before shipping, and any damage is the responsibility of the carrier, who should be notified immediately.
Warranty Registration
Thank you for purchasing a Windsor product. Warranty registration is quick and easy.
Your registration will allow us to serve you better over the lifetime of the product.
To register your product go to:
www.windsorind.com/WarrantyRegistration.aspx
For customer assistance:
1-800-444-7654
1
ADMIRAL 86038270 04/26/11
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
! WARNING:
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before
maintenance or service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near
children.
Use only as described in this manual. Use only manufacturer’s recommended components and
attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding
the machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or
dropped into water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord
around sharp edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this
machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals,
factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
ADMIRAL 86038270 05/22/07
2
CONTROLS/COMPONENT LOCATIONS
8
9
5
4
6
1.
Main Handle. Used to pull and maneuver
machine.
2.
Handle Adjustment. Used to adjust height of
handle.
3.
Electrical Cord.
4.
Solution Switch. Turns on pump. Continuous
position (bottom) activates electro-valve to
dispense solution to floor through jets.
Intermittent position (up) requires operator to
depress 1 of 3 trigger switches to dispense
solution. Center position is off.
5.
Brush Motor Switch. Turns on brush motor.
6.
Vacuum Motor Switch. Turns on vacuum
motor.
7.
Trigger Switches. Activates electro-valve to
dispense solution to floor through jets when
solution switch is in the intermittent position.
8.
Brush Motor Circuit Breaker. 4 amp.
Breaker protecting brush motor.
9.
Vacuum Motor Circuit Breaker. 7 amp.
Breaker protecting vacuum motor.
10.
Recovery Dump Hose. Facilitates draining
dirty cleaning solution.
11.
Solution Dump Hose. Facilitates draining
excess cleaning solution from solution tank.
7
1
3
10
2
11
3
ADMIRAL 86038270 05/22/07
CONTROLS/COMPONENT LOCATIONS
1.
Solution Accessory Tool Hookup. Used
for various auxiliary cleaning tools.
2.
Vacuum Hose Door. Used to connect
various auxiliary 1 ½ inch cleaning tool
vacuum hoses.
3.
Brush Height Adjustment. Used to
regulate brush height from storage position
to various carpet heights.
4.
Recovery Tank. Used to collect dirty
cleaning solution.
5.
Solution Tank. Used to hold cleaning
solution.
6.
Recovery Tank Dome.
7.
Vacuum Shoe.
8.
Brush Housing.
9.
Front Lifting Handle.
10.
Cleaning Solution Filter.
11.
Solution Tank Fill Hose.
11
10
1
9
3
2
6
4
5
7
8
ADMIRAL 86038270 05/22/07
4
CONTROLS/COMPONENT LOCATIONS
1.
Solution Intake Cover.
2.
Vacuum Intake Cover.
3.
Float Shut-Off.
4.
Clean-Out Opening.
5.
Pour Spout.
6.
Lift Handle.
6
1
2
4
6
5
3
5
ADMIRAL 86038270 05/22/07
FILLING OPERATIONS
STEP
1
RECOVERY TANK
Remove recovery
tank
SOLUTION
TANK
STEP
2
or
Add water
8 gal.
(30.3 ltr.)
140°F (60°C)
FILL LINE
STEP
3
FILLING THE ADMIRAL
8 – 16oz.
(237ml – 473ml)
NOTE: Use clean bucket of water to fill solution tank
Add cleaning
chemical
Do not put defoamer, solvents, spotter or
prespray chemicals in the solution tank.
Do not allow water to spill into vacuum motor inlet. Dry
spillage from top of solution tank before replacing
recovery tank.
STEP
CHEMICALS
Suitable Chemicals
Alkalis
Detergents
Hydroxides
Soaps
Vinegar
Non-Compatible Chemicals
Aldehydes
Aromatic Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
Chlorinated Bleaches
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
D-Limonene
4
Replace recovery
tank
* Product Trademark Names
ADMIRAL 86038270 05/22/07
6
OPERATIONS
STEP
1
STEP
2
STEP
3
1/8in
(3mm)
CORRECT
Remove electrical cord and literature
from recovery tank. Fill solution tank
(see filling instructions page 6).
Plug cord into grounded outlet. Note:
Be sure dome is seated on recovery
tank, and float shut-off is installed
correctly.
Adjust brush to proper setting. Note:
For good operation the brush must
skim the carpet. If circuit breaker
trips raise brush to prevent damage
to motor or carpet.
INCORRECT
STEP
4
SOLUTION
BRUSH
VACUUM
INT
ON
ON
Turn on brush and vacuum motor
switches (“ON”=“I”). Turn on solution
switch for continuous spray or set
switch to intermittent to allow use of
trigger switches.
CONT
7
ADMIRAL 86038270 05/22/07
OPERATIONS
Adjust handle to comfortable
operating position. Tip machine
back by main handle to move to
starting point.
STEP
Lower machine to floor.
STEP
Select continuous setting to start
solution spray or select intermittent
setting to enable use of trigger
switches to start solution spray.
The intermittent setting requires the
operator to hold any one of the
three trigger switches in the “on”
position with the fingers, and is
typically used in small areas where
short cleaning passes are made.
The continuous setting allows the
operator to set the switch in the “on”
position with one touch, and is
typically used in large areas where
long cleaning passes are made.
STEP
5
6
7
ADMIRAL 86038270 05/22/07
INT
CONT
8
CLEANING PROCEDURE
STEP
1
STEP
2
1ft.
(30cm)
OFF
STEP
1in.
(25mm)
3
SOLUTION
INTAKE COVER
VACUUM
INTAKE COVER
9
STEP
4
Start at wall closest to power outlet.
Pull straight back without pushing
down on handle.
Release intermittent trigger
switches or turn off continuous
setting on solution switch
approximately 1 foot before ending
cleaning pass.
Push down on handle to raise
vacuum shoe and brush before
moving to the next cleaning pass.
Overlap brush contact area a
minimum of 1inch on the right
(close cleaning) side of machine.
During operation, observe the following:
The Admiral is equipped with clear
internal covers to facilitate operator
viewing of dirty solution and vacuum air
flow.
During operation, observe the vacuum
intake cover. Large amounts of water or
foam entering the vacuum system can
damage the vacuum motor. If you
notice either condition, shut down the
machine immediately. Empty recovery
tank and/or add defoamer to recovery
tank.
ADMIRAL 86038270 05/22/07
CLEANING PROCEDURE
Use right side of machine for
cleaning against walls.
STEP
After cleaning, turn off all controls,
return brush to storage position and
carefully unplug machine.
STEP
5
6
OFF
OFF
To speed drying, use a
Windblower™ fan.
STEP
Empty recovery tank by releasing
dump hose. Use a hose with cold
water to clean out the recovery tank.
Also drain solution tank after each
use.
STEP
OFF
7
8
RECOVERY
DRAIN
SOLUTION
DRAIN
ADMIRAL 86038270 05/22/07
10
ACCESSORY TOOL USAGE
STEP
1
Use only one of the following
acceptable accessory tools.
86000020 – PRV NO. HT
86000000 – PRV NO. DDH
86041150 – PRV NO. DH
86031540 – PRV NO. 39504
86000610 – PRV NO. 89227
86000600 – PRV NO. 89226
Pull back collar and insert over machine
mounted fitting, then release collar to
lock into place.
STEP
2
STEP
3
SOLUTION
BRUSH
INT
VACUUM
ON
Lift door on front of vacuum shoe and
insert 1 ½ inch hose cuff into hole.
Turn on vacuum motor switch and set
solution switch to intermittent position.
Note: Be sure brush switch is in off
position and brush is in storage position.
OFF
STEP
4
11
Squeeze handle on accessory tool to
begin cleaning.
ADMIRAL 86038270 05/22/07
TROUBLESHOOTING CHART
PROBLEM
CAUSE
SOLUTION
1. Is the cord plugged in.
1. Plug in cord.
2. Circuit breaker tripped in building.
2. Reset breaker
3. Faulty switch.
3. Call for service.
4. Faulty power cord or pigtail.
4. Call for service.
Vacuum Motor Will Not
1.Vacuum circuit breaker tripped.
1.Reset breaker
Run
2.Faulty main vacuum switch.
2.Call for service.
3.Loose wiring.
3.Call for service.
4.Faulty vac motor.
4.Call for service.
Vacuum Motor Runs But
1.Debris lodged in vac shoe.
1.Remove debris from vac shoe.
Suction Is Poor
2.Dome gasket defective or missing.
2.Replace as necessary.
3.Vacuum hose cracked or hose cuff loose.
3.Replace or repair as necessary.
4.Recovery tank full / float ball stuck in the up
4.Turn off vac motor. Drain and rinse
No Power, Nothing Runs
recovery tank.
position.
Poor Or No Water Flow
1.Main pump switch off.
1. Turn on.
(Carpet Is Streaky)
2.Jets clogged or missing.
2.Clean using a vinegar /water solution or
replace.
3.Solution filter clogged.
3.Drain solution tank and clean solution
filter.
Brush Does Not Spin
4.Faulty solenoid.
4.Call for service.
1.Brush switch off.
1.Turn on brush switch.
2.Brush circuit breaker tripped
2.Reset circuit breaker.
3.Brush belt broken.
3.Replace as necessary.
4.Faulty brush motor.
4.Call for service.
ADMIRAL 86038270 05/22/07
12
THIS PAGE LEFT INTENTIONALLY BLANK
13
ADMIRAL 86038270 05/22/07
WIRING DIAGRAM
86268290
PRV NO. 88229
86268460
PRV NO. 88333
86268430
PRV NO. 88323
FILTER
86003650
PRV NO. 34362
86268370
PRV NO. 88276
86268430
PRV NO. 88323
86238830
PRV NO. 41355
86268900
PRV NO. 88655
86238840
PRV NO. 41356
86266720
PRV NO. 880043
86268430 - PRV NO. 88323
86268420
PRV NO. 88317
86268750
PRV NO. 88567
86238820
PRV NO. 41351
86001240
PRV NO. 14020
ADMIRAL 86038270 05/22/07
14
MAINTENANCE
PERIODIC MAINTENANCE
Twice a month, flush a white vinegar solution (One
quart vinegar to two gallons of water) or anti-browning
solution (mixed as directed) through the extractor. This
will prevent build-up of alkaline residue in the system. If
spray jets become clogged, remove the spray tips,
wash them thoroughly, and blow-dry.
NOTE: Always store machine with brush
in “Store” position.
NOTE: Do not use pins, wire, etc. to clean nozzles as
this could destroy spray pattern.
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked
hoses should be repaired or replaced to eliminate
vacuum or solution pressure loss. If the cable
insulation is broken or frayed, repair or replace it
immediately. Don’t take chances with electrical fire or
shock.
DAILY / REGULAR MAINTENANCE
Before making any adjustments or repairs to the
machine, disconnect the power cord from electrical
source.
1. Empty unused cleaning solution from the solution
tank.
2. Inspect and clean filter screen in solution tank.
3. Flush pumping system with 4 or 7 liters of clean,
hot water.
4. After each use, rinse tank with fresh water.
Periodically inspect the recovery tank and
decontaminate if necessary, using a Hospital Grade
Virucide or a 1-10 bleach to water solution. Waste
water should be disposed of properly.
5. Check for and remove any lint or debris around vac
shoe.
6. Check spray jets for full spray pattern.
7. Remove lint and dirt build-up from brush and
housing.
NOTE: Brush removal.
A. To remove brush, grab and pull brush out from
end opposite drive belt (operator’s right).
Remove other end from brush driver.
B. To install brush, line up slots in brush core with
pin in driver on drive belt side (operator’s left)
and push brush onto driver. Then snap bearing
end (opposite end) of brush into retaining clip.
8. Check cooling air screen (located on frame behind
left wheel) for lint or debris.
9. Check float and shut-off screen and clean as
necessary.
15
ADMIRAL 86038270 05/22/07
MAINTENANCE
! WARNING:
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM
THE FOLLOWING REPAIRS.
VACUUM MOTOR REPLACEMENT
1. Turn off all switches and unplug machine.
2. Remove recovery tank.
3. Remove the (2) screws that fasten the
solution tank to the frame, and tilt tank back
to expose the inside of the frame.
4. Locate the vacuum motor wires and
disconnect at the connector. Close the
solution tank.
5. Remove the (6) screws holding the vacuum
motor cover (p/n 86003080 – PRV NO.
27809) to the solution tank.
6. Remove the vacuum motor.
7. Reverse process to install vacuum motor.
Vacuum Motor Carbon Brushes Replacement (Windsor)
Vac Motor Carbon Brushes Replacement (Ametek)
End Cap
Carbon Brushes
WARNING: The green
ground wire must be
attached for safe
operation.
See wiring diagram.
Note: When replacing carbon vac motor brushes
loosen wire terminal BEFORE removing screws on
bracket.
If armature commutator is not concentric, extremely
pitted, or grooved the motor will need to be replaced
or sent to a qualified service center to restore vac
performance.
Wire Terminal
Wire
Terminal
End Cap
Carbon
Brushes
WARNING: The green
ground wire must be
attached for safe
operation. See wiring
diagram.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
Important:
These brushes wear quicker as the length shortens due
to increased heat. Spring inside brush housing will
damage motor if brushes are allowed to wear away
completely.
Important:
These brushes wear quicker
as the length shortens due to
increased heat.
Spring inside brush
housing will damage motor
if brushes are
allowed to wear away
completely.
Note:
Place
stop in
groove.
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less
than 3/8" long.
3 [9.5mm]
8
Periodically check the length of the carbon brushes.
Replace both carbon brushes when either is less than 3/8"
(9.5mm) long.
ADMIRAL 86038270 05/22/07
16
MAINTENANCE
SOLUTION PUMP REPLACEMENT
1. Turn off all switches and unplug the machine.
2. Remove recovery tank.
3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the inside of the
frame.
4. Remove solution hoses from fittings in pump.
5. Remove the (2) screws that fasten the pump to the frame.
6. Reverse process to install pump.
Pump Replacement Parts for Shurflo 100 psi (86026400 – PRV NO. 65254)
PumpHead
86251040
PRV NO. 65187
Pressure Switch
86161980
PRV NO. 42-809332
Valve Asm
86258830
PRV NO. 84161
Diaphragm
86003400
PRV NO. 29206
Pump Head Pump Replacement Parts for Flojet 100 PSI 230V (86004770 – PRV NO. 47477)
Motor
86251090
86247370 - PRV NO. 53246
PRV NO. 65204
Valve Asm
86258860
PRV NO. 84166
Diaphragm
86235120
PRV NO. 29219
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS.
! WARNING:
BELT REPLACEMENT
1. Turn off all switches and unplug machine.
2. Remove recovery tank and brush.
3. Remove the (2) screws that fasten the solution tank
to the frame, and tilt tank back to expose the inside
of the frame.
6. Remove the (3) screws that fasten
the side plate (p/n 86249420 – PRV
NO. 62759) to the brush housing to
remove belt.
NOTE: All components associated with
driving the brush will come out with the
side plate.
7. Reverse process to install belt.
4. Loosen the (4) screws that hold the brush motor in
place and slide motor forward to release tension in
belt.
86249420
PRV NO. 62759
5. Remove the (2) screws that fasten the vacuum shoe
links (p/n 86227350 – PRV NO. 05016) to the brush
housing.
86227350
PRV NO. 05016
17
ADMIRAL 86038270 05/22/07
TECHNICAL SPECIFICATIONS
POWER TYPE
GENERAL DIMENSIONS/WEIGHT
ELECTRICAL: 230-240 V, 7 A, 50 HZ
Vacuum shoe: 17” (43.18 cm) cast aluminum
with spring loaded down pressure
ELECTRIC VACUUM MOTOR: (1) –3 stage, 1
hp, 99 cfm (2.80 cubic meters/min.) Waterlift –
117” (297cm)
WHEELS: (2) 10” dia. (25 cm) wheels by 2”
WEIGHT: 92 lbs. (42 kg)
BRUSH: (1) 15” (38.1 cm.)
LENGTH: 35” (89 cm)
SOLUTION PUMP: 100 PSI, diaphragm style,
internal bypass
HEIGHT: 42” (107 cm)
SOLUTION CAPACITY: 8 gallons (30.3 ltr)
WIDTH: 18.5” (47 cm)
RECOVERY CAPACITY: 8 gallons (30.3 ltr)
SOLUTION SPRAY: 2 quick change jets.
BRUSH SPEED: 1000 rpm
POWER CABLE: 50’ (12.7 m) (1 mm)
42”
(107cm)
35”
(89cm)
18.5”
(47cm)
ADMIRAL 86038270 05/22/07
18
FRAME ASSEMBLY
30
7
19
18
15
(SEE PG. 31)
A
21
B
12
33
11
28
10
3
34
31
6
C
5
(SEE PG. 29)
22
26
9
32
2
25
27
16
29
8
13
20
19
14
4
24
ADMIRAL 86038270 07/14/14
FRAME ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
86003620
86004340
86001660
86238820
86239610
86005370
86005640
86005810
86198530
86249430
86006020
86250130
86250140
86276410
86273980
86010630
86010660
86010650
86006550
86256190
86226050
86066230
86134490
86253090
86002370
86233140
86274760
86006530
86272160
86276610
86005710
OPEN
34341
39528
41236
41351
41354
53641
57030
57245
99809
62761
64099
66282
66288
70643
70066
OPEN
87013
87025
87018
70074
73197
OPEN
89279
03107
99667
73943
20035
20041
70271
70057
66052
70697
57105
1
1
2
1
1
1
2
3
2
1
1
6
2
2
2
2
2
2
2
1
2
1
10”
1
1
1
2
2
1
1
3
DESCRIPTION
FRAME, CLP FAMILY
HOSE ASM, 1.5 BLK VAC X 15.5
HUBCAP, 5/8" SHAFT
HARNESS, MAIN, CLP/ADM
HINGE, TANK TO FRAME
MOTOR ASM, BRUSH 230V
NUT, 10-32 HEX NYLOCK
NUT, 1/4-20 HEX NYLOCK SS
FOAM TAPE, 1/8 THK X 3/4 1SDA
PLATE, BRUSH MTR CLAMP
PULLEY, 1.4 OD, 6GR, MICRO-V
PLUG, HOLE, .375" BLK
PLUG, 9/16 OD BLK NYLON
SCR, 1/4-20 X 3/8PPHMS
SCR, 10-32 X 3/4 PPHMS
WASHER, 1/4 ID X 5/8 OD SS
WASHER, 1/4 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
SET SCR, 10-32 X 1/4 KCP
STRAIN RELIEF, 90 DEGREE
WHEEL, 9.75" X 1.5"
AXLE, 5/8 X 17.06L
HEAT SHRINK, 3/4 ID UL/CSA
SEAL, FRAME/TANK
CLAMP, 7/16 DIA NYLON UL
CLAMP, 2.0" WORM GEAR
SCR, 1/4-20 X 1/2 HHCS PLTD
SCR, 1/4-20 X 1 PPHMS SS
PIN, ROLL 1/8” X 1.0”L
SCR, ¼-20 X 1.25 PPHMS SS
NUT, ¼-20 HEX W/ STAR WASHER
ADMIRAL 86038270 07/14/14
SERIAL NO.
FROM
NOTES:
1000045872
1000045872
20
BRUSH ASSEMBLY
31
15
25
11
7
25
29
30
8
16
12
26
24
38
18
16
30
39
10
22
34
4
44
45
36
47
40
37
33
41
26
32
17
28 35
3
43
21
13
42
1
27
6
19
14
17
23
20
30
25
29
25
46
3
9
2
5
21
ADMIRAL 86038270 05/22/07
BRUSH ASSEMBLY
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
86000730
86227100
86000900
86001100
86001140
86001300
86001310
86003620
86004060
86004470
86004980
86093080
86005110
86005120
86005130
86005640
86005850
86249410
86249420
86005930
86250680
86006220
86006430
86006510
86006590
86006650
86006700
86275530
86010640
86010650
86007030
86230620
86251710
86003070
86003370
86278130
86272770
86272510
86008650
86342240
86006030
86003390
86001140
86227150
86228890
86028010
86004750
03110
04084
09019
11045
12514
140343
140351
34341
36192
41345
50998
51311
51312
51314
51317
57030
57271
62758
62759
62762
64098
66192
67411
70043
70088
70177
70232
70497
87016
87018
70675
12524
67467
27805
29157
70737
67094
66310
80604
64102
29208
12514
05158
09137
47383
47416
1
1
2
1
1
1
1
REF
2
1
1
1
1
2
1
4
2
1
1
2
1
1
1
2
8
7
2
2
4
6
4
1
1
1
1
1
1
2
2
1
1
1
1
1
2
1
REF
AXLE, ROLLER
ADAPTER, BRUSH BRG.
BEARING, 1.125ODX.500IDX.375
BELT, 180J6 MICRO-V
BRUSH, 15L X 3.38OD
BRKT, BRUSH PULLEY
BRKT, BRUSH HEIGHT
FRAME, CLP FAMILY
GUARD, THREAD
HOUSING, BRUSH 15"
LABEL, BRUSH HEIGHT
LINKAGE, ASM, BRUSH HEIGHT
LINKAGE ASM, ROLLER SUPPORT
LINK, ROLLER, FRONT
LEVER, HEIGHT ADJUSTMENT
NUT, 10-32 HEX NYLOCK
NUT, 3/8 DIA CAP, TYPE PUSH PLT
PLATE, BRUSH HOUSING RH
PLATE, BRUSH HOUSING LH
PLATE, AXLE RETAINER
PULLEY, 2.2 OD, 6GR, MICRO-V
PIN, ROLL 1/4 X 1.25L
ROLLER, 1.9 DIA X 10.5 LG
SCR, 10-32 X 5/8 PFHMS
SCR, 10-32 X 1/2 PPHMS SS DL
SCR, 10-32 X 1/2 FHMS SS
SCR, 10-32 X 3/8 FHMS SS
SCR, #10-24 X 1/2 SHCS
WASHER, #10 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
SCR, 1/4-20 X.5/8 THMS PLTD NP
BRUSH 15 L X 3.38 OD G2
RING, TOLERANCE 7/8 ID X 1/2 W
CLIP, BEARING
DRIVER, BRUSH
SHLDR BOLT, 3/8 OD X 3/8 L SS NP
RING, 1/2 EXT. SNAP
PIN, CLEVIS 1/4 X 1/2 PLTD
COTTER, 1/4" RING
SPACER, .81 X 1.06 X.125
PULLEY ASM, BRUSH
DRIVER ASM, BRUSH
BRUSH ASM, 15 IN
ADAPTER, BRUSH BRG DIE CAST
BEARING, R6 3/8 ID
BRUSH BEARING ASM
KIT, BRNG/ADPTR EXTRCTR
ADMIRAL 86038270 02/22/11
SERIAL NO.
FROM
NOTES:
1000060649
1000060649
1000060649
1000060649
1000060649
22
PUMP ASSEMBLY
3
20
29
29
17
4
13
28
10
16
8
2
16
21
23
18 1
12
19
15
20
11
26
9
7
25 22
22
25
D
6
(SEE SOLUTION
TANK)
26
23
24
27
ADMIRAL 86038270 05/22/07
5
PUMP ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
86002470
86002480
86003470
86003490
86004570
86241680
86005640
86026400
86250140
86274410
86273750
86003640
86008360
86010570
86010810
86010650
86010820
86005590
86005580
86003500
86006590
86279930
86267400
86282340
86282350
86281900
86253020
86197400
86227950
22072
22090
31072
31074
44067
44073
57030
65254
66288
70195
70011
34355
78419
84165
87191
87018
87192
56014
56012
31076
70088
29277
880278
39720
39721
39531
73963
31022
140387
1
2
1
1
2
2
2
1
2
2
2
1
1
1
2
4
2
1
1
2
2
2
1
1
2
3
1
1
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
COUPLING, 1/4 ANCHOR W/1" HEX
CONNECTOR, 1/8FPT X 1/4 TUBE QC
ELBOW, SWIVEL, 1/4MPTX1/4TUBE
ELBOW, SWIVEL,3/8MPTX3/8TUBE QC
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9503
NUT, 10-32 HEX NYLOCK
PUMP ASM, 230V 100PSI W/CONN
PLUG, 9/16 OD BLK NYLON
SCR, 10-32 X 1.25 PPHMS
SCR, 1/4-20 X 5/8 HHCS SS
FITTING,1/4 TUBE,"Y", QC
TEE, 3/8 MPT X 3/8 TUBE, QC
VALVE ASM,SOLENOID CLP FAMILY
WASHER, 1/4"IDX1.0OD. FLAT SS
WASHER, #10 X 9/16 OD
WASHER, 7/16 X 3/4 X .19RUBBER
NIPPLE, 1/4 CLOSE
NIPPLE, 1/4 FPT QD
ELBOW, 1/4 MPT X 3/8 TUBE, QC
SCR, 10-32 X 1/2 PPHMS SS
DUCT, 1/2 ID SPLT FLX X 16”
WIRE, 22" GRN/18 76011 X 76011
HOSE, 3/8 OD X 1/4 ID URTHN X 22”
HOSE, 3/8 ID NYLON YLW X 17”
HOSE, 1/4 ID NYLON YLW X 5”
SCREEN, INTAKE
ELBOW, 1/8NPT STREET
BANDS, RUBBER
ADMIRAL 86038270 05/22/07
24
PUMP ASSEMBLY
PRIOR TO S/N 1000153482
14
3
20
8
13
4
10
16
9
2
16
21
23
18 1
12
19
15
20
11
17
7
25
26
28
D
(SEE SOLUTION
(SEE
PG. 29)
TANK)
26
24
27
25
ADMIRAL 86038270 05/22/07
6
5
PUMP ASSEMBLY
PRIOR TO S/N 10000153482
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
86002470
86002480
86003470
86003490
86004570
86241680
86005640
86004770
86250140
86006830
86273750
86003640
86008360
86010570
86010810
86010650
86010820
86005590
86005580
86003500
86006590
86267400
86281890
86004350
86281900
86253020
86285760
22072
22090
31072
31074
44067
44073
57030
47477
66288
70386
70011
34355
78419
84165
87191
87018
87192
56014
56012
31076
70088
OPEN
880278
39529
39530
39531
73963
39551
1
2
1
1
2
2
2
1
2
2
2
1
1
1
2
4
2
1
1
2
2
1
1
1
3
1
1
DESCRIPTION
COUPLING, 1/4 ANCHOR W/1" HEX
CONNECTOR, 1/8FPT X 1/4 TUBEQC
ELBOW, SWIVEL, 1/4MPTX1/4TUBE
ELBOW, SWIVEL,3/8MPTX3/8TUBEQC
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9503
NUT, 10-32 HEX NYLOCK
Kit, 230V FLOJET PUMP REPLMNT
PLUG, 9/16 OD BLK NYLON
SCR, 10-32 X 1.0 PPHMS
SCR, 1/4-20 X 5/8 HHCS SS
FITTING,1/4 TUBE,"Y", QC
TEE, 3/8 MPT X 3/8 TUBE, QC
VALVE ASM,SOLENOID 230V
WASHER, 1/4"IDX1.0OD. FLAT SS
WASHER, #10 X 9/16 OD
WASHER, 7/16 X 3/4 X .19RUBBER
NIPPLE, 1/4 CLOSE
NIPPLE, 1/4 FPT QD
ELBOW, 1/4 MPT X 3/8 TUBE, QC
SCR, 10-32 X 1/2 PPHMS SS
WIRE, 22" GRN/18 76011 X 76011
HOSE, 3/8 URETHANE X 29"
HOSE, 3/8 NYLON X 6"
HOSE, 1/4 ID NYLON X 6"
SCREEN, INTAKE
HOSE, 3/8 NYLON X 29”
ADMIRAL 86038270 05/22/07
SERIAL NO.
FROM
NOTES:
100003082
1000045872
26
VACUUM SHOE ASSEMBLY
1
4
11
7
13
10
2
12
3
5
8
6
7
11
27
ADMIRAL 86038270 05/22/07
VACUUM SHOE ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
86227350
86234760
86005810
86006790
86275120
86006840
86008130
86010620
86010630
86010700
86003780
86008120
05016
27674
57245
70351
70360
70390
73958
85039
OPEN
87013
87074
35171
73955
4
1
4
2
4
4
8
1
4
8
1
2
DESCRIPTION
SERIAL NO.
FROM
NOTES:
ARM, VAC SHOE PARALLEL
COVER, ACCESSORY PORT
NUT, 1/4-20 HEX NYLOCK SS
SCR, 10-32 X 3/8 HHTR W/STAR
SCR, 1/4-20 X.75 PPHMS PHIL
SCR, 1/4-20 X 1 FHCS PLTD
SPACER, 3/8ODX.058WX.2814,CRS
VAC SHOE, 15"
WASHER, 1/4 ID X 5/8 OD SS
WASHER, WAVE 3/8ID X3/4D X.125
GASKET, ACCESSORY PORT
SPRING, EXT .38D X2.75L X.055W
ADMIRAL 86038270 05/22/07
28
CONTROL PANEL ASSEMBLY
29
ADMIRAL 86038270
08/30/13
CONTROL PANEL ASSEMBLY
SERIAL NO.
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36A
36B
36C
36D
37
38
39
40
41
42
43
44
45
46
47
86001240
86230110
86002020
86002010
86233240
86261000
86003130
86003140
86076550
86004100
86004110
86004790
86246300
86246650
86005670
86081530
86264270
86007140
86087410
86256180
86008350
86245950
86005760
86005810
86272190
86227650
86006870
86006620
86006790
86274150
86006710
86005750
86010750
86198480
86238820
86002610
86002600
86031550
86260960
86272840
86256170
86007200
86006830
86005700
86010660
86010670
86002870
86232290
86007130
86245040
14020
14312
14949
14942
20084
23671
27823
27824
38283
38286
38287
48012
51039
51313
57040
62766
67073
72130
73180
73195
78418
50996
57116
57245
66068
03109
70406
70127
70351
70105
70235
57113
87100
27371
41351
23683
23682
23681
23521
67147
73169
72162
70386
57104
87025
87029
27417
500017
72128
50279
1
1
1
2
2
1
3
3
2
1
1
1
1
2
2
1
1
2
1
1
3
1
2
4
1
1
9
6
5
4
2
2
2
2
REF
1
1
1
1
1
1
1
1
3
1
2
1
1
1
1
TERMINAL BLOCK, 115V (3-4-3)
BREAKER, 7A 250VAC 50VDC
BREAKER, 4A CIRCUIT
BOOT, 3/8 CIRCUIT BREAKER
CLAMP, HANDLE LOCK
CORD ASM
CONTACT, ELECTRICAL, FLAT
CONTACT, ELECTRICAL, BENT
HANDLE, ADM8
HANDLE, CONTROL PANEL FRONT
HANDLE, CONTROL PANEL REAR
KNOB, 5/16-18 4 PRONG
LEVER, HANDLE CLAMP
LINK, HANDLE ADJ.
NUT, 1/2 NPT CONDUIT
PLATE, CONTROL PANEL, CLP/ADM
ROD, HANDLE LOCK
SWITCH, SPST 2-POSITION ROCKER
SPACER, .50 ODX.058WX9.84L CRS
STRAIN RELIEF, 1/2 NPT (.48ID)
TRIGGER, SWITCH
LABEL, CONTROL PANEL, CLP/ADM
NUT, 6-32 W/STAR WASHER PLTD
NUT, 1/4-20 HEX NYLOCK SS
PIN, ROLL 1/8" X 5/8"L
AXLE, HANDLE ADM8
SCR, #10 X 3/4 PPHST TYPE B
SCR, 6-32 X 1/4 PPHMS SS
SCR, 10-32 X 3/8 HHTR W/STAR
SCR, 1/4-20 X 1.75 HHCS
SCR, 6-32 X 1.0 PH BLK NYLON
NUT, 5/16-18 HEX NYLOCK
WASHER, 3/8 ID INT.LOCK THIN
CLIP, POWER CORD
HARNESS, MAIN CLP/ADM
CORD ASM, 230V BRITIAN 50FT
CORD ASM, 230V EURO 50FT
CORD ASM, 230V SWISS 50FT
CORD ASM, 230V AUST 50 FT
RING, 2" DIA SPLIT
STRAIN RELIEF, CORD HOOK
SWITCH, DPDT3-POSITION ROCKER
SCR, 10-32 X 1” PPHMS
NUT, 10-32 W/STAR WASHER PLTD
WASHER, 1/4 LOCK EXT STAR SS
WASHER, 5/16 FLAT SS
CORD, 99807 1/8 X 12"
CARD, INSTRUCTION ADM8
SWITCH, DPDT, 2 POSITION ROCKER
LABEL, GROUND SYMBOL
ADMIRAL 86038270
08/30/13
NOTES:
30
SOLUTION TANK ASSEMBLY
6
13
3
16
7
12
10
20
15
7*
(SEE FRAME)
30
A
11
19
14*
18
24*
8
9
17*
2
32
26
1
25
18
22*
4
B
28
(SEE FRAME)
29
31
23*
21*
5*
31
16
27
ADMIRAL 86038270 05/22/07
D
(SEE PUMP)
16
27
SOLUTION TANK ASSEMBLY
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
86233140
86233150
86003080
86003090
86235500
86003790
86003920
86281880
86240090
86004340
86240980
86005420
86275690
86032260
86259060
86010650
86007970
86010630
86006580
86233260
86003950
86003960
86003970
86197940
86275120
86010660
86006600
86095840
86005810
86260690
86233150
86197920
20041
20042
27809
27810
31081
35175
35231
39526
39527
39528
41348
53791
70525
75259
85037
87018
73864
87013
70085
20092
35236
35237
35238
40027
70360
87025
70114
89183
57245
02130
20042
40023
2
1
1
1
1
2
2
1
1
REF
1
1
6
1
1
10
1
5
3
1
1
1
1
1
2
2
4
1
2
1
1
1
CLAMP, 2.0" WORM GEAR
CLAMP, 3/8 HOSE (D-SLOT)
COVER, VAC MOTOR
COVER, BELT
ELBOW, 3/8 MPT X 3/8 TUBE, PLASTIC
GASKET, TANK TO VAC COVER
GASKET, VAC COVER (CLP FAMILY)
HOSE,1/2 CLEAR X 12
HOSE, 1.5 BLK VAC X 3.0
HOSE ASM, 1.5 BLK VAC X 15.5
HOUSING, VAC MOTOR
VAC MOTOR ASM, CLP FAMILY
SCR, #10 X 1.0 PPHST TYPE B
TANK, ADM SOLUTION
VENT, COOLING AIR SMALL
WASHER, #10 X 9/16 OD
STRAINER, 3/8 IN. NPT 60 MESH
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 1/2 PPHMS SS DL
CLAMP, 3.5" WORM GEAR
GASKET, TANK, L-F
GASKET, TANK, L-R
GASKET, TANK, RH
HOSEBARB, 3/8MPTX1/2 90D DL
SCR, 1/4-20 X.75 PPHMS PHIL
WASHER, 1/4 LOCK EXT STAR SS
SCR, #10 X 3/4 PPHST TYPE B
WELDMENT, HANDLE PIVOT ADM8
NUT, 1/4-20 HEX NYLOCK SS
HOSE ASSY- FILL HOSE
CLAMP, 3/8 HOSE (D-SLOT)
HOSEBARB, 1/2MPT X 3/8 DL
33
86026670
75277
1
TANK ASM, SOLUTION ADM8
ADMIRAL 86038270 05/22/07
SERIAL NO.
FROM
*
NOTES:
ITEMS
INCLUDED
32
RECOVERY TANK ASSEMBLY
16
15
5
E
18
7
11
4
12
8
10
E
1
14
9
12
13
17
2
6
11B
3
10B
1B
14B
12
33
ADMIRAL 86038270 05/22/07
RECOVERY TANK ASSEMBLY
REF
PART NO.
PRV NO.
QTY
1A
1B
2
3
4
5
6
7
8
9
10A
10B
11A
11B
12
13
14A
14B
15
16
17
18
86002400
86002350
86233140
86008400
86003110
86235280
86003630
86003910
86003930
86004200
86004510
86004450
86004500
86006240
86006600
86032270
86001370
86001190
86002870
86242230
86245930
86003330
20064
20002
20041
78499
27816
28060
34351
35230
35232
39353
41391
40019
41390
66227
70114
75260
140408
140133
27417
500009
50994
28061
1
1
1
1
2
1
1
1
2
1
1
1
1
1
6
1
1
1
1
1
1
1
DESCRIPTION
CLAMP, 2.0" WORM GEAR X .312
CLAMP, 2.0” NYLON RATCHET
CLAMP, 2.0" WORM GEAR
TETHER, DRAIN PLUG
COVER, REC. TANK
DOME, CLP FAMILY
FLOAT SHUT-OFF
GASKET, DOME
GASKET, PORT COVER
HOSE, 1.5 X 12.0 DRAIN
HOSE, INSERT
HOSEBARB, 1.5 DOUBLE MCHD
HOSE, CAP
PLUG, DRAIN HOSE
SCR, #10 X 3/4 PPHST TYPE B
TANK, ADM RECOVERY
BRKT, HOSE HOOK
BRKT, RECOVERY HOSE MTG
CORD, 99807 1/8 X 12"
LABEL, WARNING
LABEL, ADMIRAL MAIN
DOME ASM, CLP FAM
ADMIRAL 86038270 05/22/07
SERIAL NO.
FROM
1000084015
NOTES:
1000084015
1000084015
1000084015
34
SUGGESTED SPARE PARTS
35
PART NO.
PRV NO.
86001140
86001100
86000900
86004570
86241680
86004770
86010570
86003780
86230110
86002020
86007140
86007200
86005420
86007970
86230760
86135330
86003330
86003630
86006240
12514
11045
09019
44067
44073
47477
84165
35171
14312
14949
72130
72162
53791
73864
140216
140688
28061
34351
66227
DESCRIPTION
BRUSH, 15L X 3.38OD
BELT, 180J6 MICRO-V
BEARING, 1.125ODX.500IDX.375
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9503
KIT, 230V FLOJET PUMP REPLACEMENT
VALVE ASM
GASKET, ACCESSORY PORT
BREAKER, 7A
BREAKER, 4A
SWITCH, SPST 2-POSITION ROCKER
SWITCH, DPDT3-POSITION ROCKER
VAC MOTOR ASM, 230V
STRAINER, 3/8 IN. NPT 60 MESH
BRUSH SET, 230V VAC AMETEK
BRUSH SET, 230V VAC MTR WINDSOR
DOME ASM, CLP FAMILY
FLOAT SHUT-OFF
PLUG, DRAIN HOSE
ADMIRAL 86038270 10/12/07
SERIAL NO.
FROM
*
NOTES:
ADMIRAL 86038270 05/22/07
36