Download Sharp MD-SR75H Specifications

PORTABLE MINIDISC RECORDER
OPERATION MANUAL
Thank you for purchasing this SHARP product.
For the best performance, read this manual carefully.
It will guide you in operating your SHARP product.
If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/support.
Customers without internet access may telephone
0990 274277 during office hour.
MODEL
MD-SR75H
Accessories
Remote Control x 1
Earphones x 1
AC Adaptor
(RADPA8046AWZZ or
RADPA8039AWZZ) x 1
Rechargeable
Nickel-Metal Hydride Battery
(AD-N70BT) x 1
Battery Carrying Case x 1
Connection Cable
(for analogue recording) x 1
Connection Cable
(for digital recording) x 1
Carrying Bag x 1
Notes:
● Parts and equipment mentioned in this operation manual
other than those detailed above are not included.
● The AC adaptor may be different from the one in the
drawing.
2
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Contents
Important Introduction
Advanced Features
Special Notes ................................................ 4-5
Names of Controls and Indicators .............. 6-7
Precautions ....................................................... 8
Hold Function ................................................... 9
How to Use the Shuttle .................................. 10
Preparation
Inserting a MiniDisc ....................................... 11
Connections .............................................. 12-13
Basic Operation
Recording .................................................. 14-15
Playback .................................................... 16-17
Changing Default Settings ............................ 33
Titling a MiniDisc ...................................... 34-37
Editing a Recorded MiniDisc ................... 38-39
References
Other Features and Caution .......................... 40
DEUTSCH
MiniDisc System Limitations ......................... 41
Error Messages ........................................ 42-43
Troubleshooting ....................................... 44-45FRANÇAIS
Maintenance .................................................... 45
Specifications ................................................. 46
Index ................................................................ 47ESPAÑOL
TERMS OF GUARANTEE .............. Back coverSVENSKA
Useful Features
Advanced Playback .................................. 18-19
Advanced Recording ............................... 20-24
Recording from a Microphone ................ 25-27
Checking Displays ................................... 28-29
Battery Power ........................................... 30-31
Listening to a MiniDisc Through a Stereo
System or a Car Stereo ................................ 32
Web-site: www.sharp.co.uk/support
ITALIANO
NEDERLANDS
ENGLISH
Help Line: 0990 274277 (office hours)
3
4
Warnings
NOTE FOR USERS IN THE U.K.
– Special Notes –
Important Introduction
Special Notes
SERVICE INFORMATION
In the unlikely event of your equipment requiring repair, please contact the dealer or supplier from whom
it was purchased. Where this is not possible, please
visit our web-site www.sharp.co.uk/support.
Customers without internet access may telephone
0990 274277 during office hour.
Please note; all calls will be charged at local rate.
Certain replacement parts and accessories may be
obtained from our main parts distributor.
WILLOW VALE ELECTRONICS LTD.
0121 766 5414
● The supplied AC adaptor contains no user ser-
viceable parts.
Never remove covers unless qualified to do so. It
contains dangerous voltages, always remove
mains plug from the main outlet socket before any
service operation or when not in use for a long
period.
● The AC adaptor supplied with the MD-SR75H must
not be used with other equipment.
● To prevent fire or shock hazard, do not expose
this appliance to dripping or splashing liquids.
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
● Never use an AC adaptor other than the one specified.
Otherwise, problems or serious hazards may be
created.
In the unlikely event of this equipment requiring repair during the guarantee period, you will need to
provide proof of the date of purchase to the repairing
company. Please keep your invoice or receipt, which
is supplied at the time of purchase.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
pocket, as this may damage the product when sitting.
● At full volume, prolonged listening to a personal stereo
may damage the user’s hearing.
This model complies with the law if used with the correct
earphones (model number RPHOH0176AFZZ).
If the earphones are damaged in any way, please order
using the model number given above.
● Use the Portable Minidisc Recorder only in accordance
with the instructions given in this manual and do not attempt to interfere with the interlock switch or make any
other adjustment as this may result in exposure to hazardous radiation.
DEUTSCH
– Special Notes –
● It is not recommendable to put the MiniDisc into a rear
Cautions
Important Introduction
Special
Special
Notes
Notes
: continued
FRANÇAIS
Notes
ESPAÑOL
● Recording and playback of any material may require
consent, which SHARP is unable to give. Please refer
particularly to the provisions of the Copyright Act 1956,
SVENSKA
the Dramatic and Musical Performers Protection Act
1958, the Performers Protection Acts 1963 and 1972 and
to any subsequent statutory enactments and orders.
ITALIANO
● This equipment complies with the requirements of
Directives 89/336/EEC and 73/23/EEC as amended by
93/68/EEC.
NEDERLANDS
● US and foreign patents licensed from Dolby Laboratories Licensing Corporation.
● The letters in brackets contained in the model number
ENGLISH
indicate the colour of the product only. Operation and
specifications are unaffected.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
5
– Names of Controls and Indicators –
Important Introduction
Names of Controls and Indicators
1
8
2
9
3
10
4
11
5
12
13
14
15
16
6
7
17
19
18
6
Web-site: www.sharp.co.uk/support
Main unit
1. Volume Up/Cursor Button (16, 35)
2. Volume Down/Cursor Button (16, 35)
3. Edit/Auto Mark/Time Mark Button
(23, 27, 34-39)
4. Display/Character Select Button (28, 29, 34)
5. Remote Control/Earphones/Line Output
Socket (16)
6. Optical/Line Input Socket (12, 13)
7. Microphone Input Socket (25)
8. Record/Track Mark Button (14, 23)
9. Stop/Power Off/Charge Button (15, 17, 30, 33)
10. Play/Pause Button (14, 16)
11. Enter/Fast Play/Synchro Button (19, 20, 34-39)
12. Fast Forward/Recording Level Up/Name
Select Button (14, 18, 33, 34)
13. Fast Reverse/Recording Level Down/
Name Select Button (14, 18, 33, 34)
14. Bass/Delete Button (16, 35)
15. Mode Button (19, 21, 33)
16. Open Lever (11)
17. 5V DC Input Socket (12, 30)
18. Battery Cover (30, 31)
19. Hold Switch (9)
Help Line: 0990 274277 (office hours)
2
5
3
6
4
Remote control unit
1. Earphones Socket (16)
2. Play/Pause/Fast Reverse/
Fast Forward Shuttle Switch (17, 18)
3. Play Mode Button (19)
4. Sound/Track Mark Button (17, 23)
5. Stop/Power Off Button (17)
6. Display/Volume Shuttle Switch (17, 28, 29)
7. Hold Switch (9)
7
Display panel
[Main unit]
1
2
3
4
5
6
10
11
12
13
14
15
16
7
8
9
[Remote control unit]
3
4
1
2
5
6 7
8
9
[Main unit]
[Remote control unit]
01. Level Meter
02. Monaural Long-Play Mode
Indicator
03. Record Indicator
04. Synchro Recording Indicator
05. Disc Mode Indicator
06. Disc Name Indicator
07. Track Name Indicator
08. Remaining Recording Time
Indicator
09. Total Track Number Indicator
10. Fast Play Indicator
11. Repeat Indicator
12. TOC Indicator
13. Battery Indicator
14. Random Indicator
15. Track Number Indicator
16. Character/Time Information
Indicator
01.
02.
03.
04.
05.
06.
07.
08.
Web-site: www.sharp.co.uk/support
Important Introduction
1
DEUTSCH
– Names of Controls and Indicators –
Names of Controls and Indicators : continued
FRANÇAIS
Record Indicator
Synchro Recording Indicator
Disc Mode Indicator
Random Indicator
ESPAÑOL
Repeat Indicator
Track Number Indicator
Total Track Number Indicator
SVENSKA
Character/Time Information
Indicator
09. Battery Indicator
ITALIANO
NEDERLANDS
ENGLISH
Help Line: 0990 274277 (office hours)
7
8
Important
Storing the unit
● Do not wear your earphones when you are crossing
streets or near traffic.
● Do not use your earphones
– Precautions –
Important Introduction
Precautions
●
●
●
●
●
whilst driving a motor vehicle, it
may create a traffic hazard and
may be illegal.
Remember to obey all of the safety
rules in your area.
Do not play the unit at a high volume. Hearing experts advise
against extended listening at high volume levels.
If you experience ringing in your ears, reduce the volume or discontinue use.
No naked flame sources, such as lighted candles, should
be placed on the apparatus.
Attention should be drawn to the environmental aspects
of battery disposal.
The apparatus is designed for use in moderate climate.
To avoid accidental electric shock or other possible
problems, observe the precautions listed below.
● Do not disassemble or modify the unit.
● Do not drop or subject the unit to shock.
● Do not use the unit near open flames.
● Do not spill liquid on the unit.
● Do not use an external power supply, other than the 5V
DC supplied with this unit, as it may damage it.
● SHARP is not responsible for damage due to improper use.
Refer all servicing to a SHARP authorised service centre.
Web-site: www.sharp.co.uk/support
Avoid using or leaving the unit in the following places.
● Places exposed to direct sunlight
for many hours (especially in cars
with the doors and windows
closed) or near heaters.
(The cabinet may deform, change
colour or the unit may malfunction.)
● Places exposed to water.
● Places exposed to excessive dust.
● Places where temperatures are excessively high or low.
● Places (bathrooms) where the humidity is extremely high.
● Places with strong magnetic
fields such as TVs or loudspeakers.
● Places exposed to vibration.
● Places where sand can easily enter
the inside of the unit (beaches etc.).
● If the unit is used near radio tuners or TVs, noise and/or
picture interference may result. If you experience these
problems, move the unit away from such devices.
Help Line: 0990 274277 (office hours)
Orange
mark
Release
Hold
Orange
mark
Hold
Move the HOLD switch to the safety position (direction indicated by the arrow).
(An orange mark appears.)
DEUTSCH
– Hold Function –
The present operation condition can be kept even
if other buttons are accidentally pressed in a place
such as a crowded train.
Important Introduction
Hold Function
● To cancel the hold mode, move the HOLD switch
away from the safety position (the opposite direction of the arrow).
FRANÇAIS
● If the hold function is active whilst the power is
turned off, the power cannot be turned on by
mistake and the battery will not be drained. ESPAÑOL
Release
SVENSKA
A HOLD switch is on both the remote control and
the main unit.
Various controls are possible depending on the comITALIANO
bination of the two switches.
NEDERLANDS
Note:
● Cancel the hold mode to operate the Portable
MiniDisc Recorder. Otherwise, it will not work. ENGLISH
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
9
10
Press.
– How to Use the Shuttle –
Important Introduction
How to Use the Shuttle
Used to begin or
pause playback.
Move to the left.
Move to the right.
Used for fast forward or to locate the beginning of any track. Also used to select a track
or to change each setting.
Used for fast reverse or to locate the beginning of any track. Also used to select a track
or to change each setting.
If you move and hold it during playback, fast
forward will be performed.
If you move and hold it during playback, fast
reverse will be performed.
Press.
Move to
the left.
Used to change the display.
During recording: Elapsed time, remaining recording time
During playback: Track name, elapsed time, remaining time
During stop:
Disc name, remaining recording time, total playing time, playing time of each track
Web-site: www.sharp.co.uk/support
The volume is
increased.
Help Line: 0990 274277 (office hours)
Move to
the right.
The volume is
decreased.
Inserting a MiniDisc
4
1
2
Lift it up.
3
Insert a MiniDisc as shown.
4
Close the compartment door.
Notes:
● Do not place the MiniDisc under the holder.
– Inserting a MiniDisc –
2
Slide the OPEN lever to release the compartment door.
Preparation
1
3
● If any resistance is felt, do not force the MiniDisc into the
Check that the erase-protection
tab is in the recordable position.
unit, as it may cause damage to the unit. If resistance is
felt, remove the MiniDisc and reload it.
● The lid can not be opend if “TOC” is displayed refer to
the instruction on page 15.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
11
Connections
You can record your favorite CDs or tapes to an MD.
To connect to a stereo system with “AUDIO OUT” or “LINE OUT” sockets
– Connections –
Preparation
AC 230-240V
50/60Hz
To the DC IN
5V socket
To the wall socket
White : To Left
To the OPTICAL/
LINE IN socket
Red : To Right
AUDIO OUT
RIGHT
12
Web-site: www.sharp.co.uk/support
LEFT
To a stereo system with “AUDIO OUT” or “LINE OUT”
sockets. (See left, Analogue connection.)
Note:
If the audio system has only one pair of sockets, they are
usually for input only and recording via this connection is not
possible.
Help Line: 0990 274277 (office hours)
Connections : continued
To connect to a stereo system with a “DIGITAL OUT” or “OPTICAL OUT” socket
To the wall socket
– Connections –
To the DC IN
5V socket
Preparation
AC 230-240V
50/60Hz
To the OPTICAL/
LINE IN socket
To a stereo system with a "DIGITAL OUT" socket.
DIGITAL OUT (See left, Digital connection.)
Compared to analogue connection recording, it allows
high-quality recording.
Note:
Some audio systems do not have a DIGITAL OUT socket.
Check before connecting.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
13
Recording
Check that the HOLD switch
on the back is released.
The unit does not work if the
switch is set to HOLD.
1
2
Press the REC button.
● Record pause mode is entered.
Begin playback on the stereo system connected to this unit.
● To enable the record level to be set.
– Recording –
Basic Operation
Before recording
3
5 or 4) button
Press the REC LEVEL (5
to adjust the recording level (analogue
connection only).
● Adjust the recording level so that the maximum
sound volume from the source makes the reading swing somewhere between –4 dB and 0 dB.
Level meter indicator
As for the details, see page 9.
0dB
4dB
● For digital connection, it is not necessary to ad-
just the recording level.
4
Press the PAUSE button on the stereo system to enter the playback pause mode at
the point you wish to start recording.
● Here you can select the track to be recorded.
5
6
14
Web-site: www.sharp.co.uk/support
Press the 06 button to start the MiniDisc
unit recording.
Begin playback on the stereo system, the
output will be recorded.
Help Line: 0990 274277 (office hours)
Recording : continued
● The track number will be increased by one each time
After any recording or editing function “TOC” (Table Of
Contents) is displayed. To finalize the recording or editing
function, press the • ■/:OFF button. During this process
“TOC” will flash and “TOC EDIT!” will be displayed.
During any recording or editing function the MiniDisc unit
Lid is locked, the MiniDisc can not be removed until the
process is finalized.
the recording is interrupted.
To stop recording
Press the • ■/:OFF button.
● When recording stops, “TOC” appears (Table Of Con-
tents). Whilst “TOC” appears the MiniDisc recorded
contents have not yet been updated.
● To prevent the new recording from being lost it is not
possible to remove the MiniDisc whilst “TOC” is displayed.
TOC display
To update the recorded contents of the MiniDisc
Press the • ■/:OFF button whilst in the stop mode.
Warning
● If the power is removed (Battery/AC adapter) whilst
“TOC” is displayed the MiniDisc unit lid will remain locked
until the battery/main power is restored and the unit is
turned on. Your new recordings or edited changes will
be lost and your MiniDisc may become unusable.
Caution:
● Whilst “TOC” or “TOC EDIT!” is displayed, do not do
any of the following.
– Do not jerk or bump the unit.
– Do not unplug the AC adaptor.
– Do not remove the rechargeable battery or an alkaline battery.
– Do not subject the unit to shock.
Otherwise, tracks may not be recorded properly.
– Recording –
To interrupt recording
Press the 06 button.
About the TOC
Basic Operation
Notes:
● Changing the volume level whilst recording does not affect the recording.
● You cannot adjust the bass level whilst recording.
● The power turns off after recorded contents have been
updated on the MiniDisc.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
15
Right
channel
– Playback –
Basic Operation
Playback
Left
channel
Before Playback
Check that the HOLD switch
on the back is released.
The unit does not work if the
switch is set to HOLD.
To the
socket
As for the details, see page 9.
16
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Playback : continued
Plug the remote control into the
on the unit.
3
Insert a MiniDisc (page 11).
4
Press the 06 button.
Volume control
Press the VOL+ button to increase the volume and
the VOL– button to decrease the volume.
socket
Volume (0 - 30)
Bass control
Each time the BASS button is pressed (Remote control: the SOUND button is pressed), the tone will be
switched as follows.
● Playback starts automatically with a playback only
MiniDisc or a MiniDisc which is protected against
accidental erasure (Auto-play function).
To interrupt playback
Press the 06 button.
● To resume playback, press the 06 button again.
To stop playback
Press the • ■/:OFF button.
● If the unit is not operated for at least 2 minutes whilst
in the stop mode, the power will shut off automatically.
To turn off the power
Press the • ■/:OFF button whilst in the stop mode.
BASS 1
Emphasised slightly
BASS 2
Emphasised more
BASS 3
Emphasised fully
BASS OFF Cancelled
Notes:
● If power failure occurs whilst playing a disc using the AC
adaptor, disconnect it from the wall socket. Otherwise, playback may start automatically when electricity resumes.
● If you connect the AC adaptor without installing the rechargeable battery, playback may start automatically. Be
sure to turn off the power.
● Reduce the volume before starting to play. MiniDiscs, compared to ordinary cassette tapes, have very little noise. If
the volume is adjusted according to your usual expectations of noise, high volume may damage your hearing.
● The sound escaping from your earphones may annoy
people around you.
In particularly crowded places (such as on trains or
buses), reduce the volume.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
– Playback –
2
Insert the earphones plug firmly into the
earphones socket on the remote control
unit.
Basic Operation
1
17
Advanced Playback
To move to the beginning of the next track:
Press the 4 button during playback.
– Advanced Playback –
Useful Features
To locate the beginning of a track
To re-start the track being played:
Press the 5 button during playback.
To locate the next track:
Press the 4 button whilst the unit is stopped.
To locate the desired portion
To locate the previous track:
Press the 5 button whilst the unit is stopped.
● To skip a number of tracks at one time, press the 5
For audible fast forward:
Press and hold down the 4 button during playback.
For audible fast reverse:
Press and hold down the 5 button during playback.
or 4 button repeatedly until the desired track number is shown.
● When you press the 06 button, play back starts from
the beginning of the track.
● Normal playback will resume when the 5 or 4
button is released.
● When the end of the last track is reached during fast
forward, the unit will enter the pause mode. When
the beginning of the first track is reached during fast
reverse, the unit will enter the playback mode.
18
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Advanced playback : continued
Random play or repeat play
To play at double speed (Mono recording only)
Press the ENTER/SYNC button whilst a MiniDisc recorded in the monaural long-play mode is being played.
● If a track recorded in the stereo mode is reached during
fast playback, the fast playback mode will be cancelled.
● Depending on the contents recorded on a MiniDisc, it
may be difficult to hear them.
To interrupt fast playback
Press the 06 button during playback.
When the 06 button is pressed again, the unit will resume
fast playback.
To return to normal playback
Notes:
● If the playback mode is selected whilst stopped, press
the 06 button to start playback.
● When “TOC” is displayed, random play or repeat play
is impossible.
● In random play the unit will select and play tracks automatically. (You cannot select the order of the tracks.)
After all of the tracks have been played once each in
random order, the unit will stop automatically.
● During random, random repeat, or single track repeat
play, you can forward or reverse the MiniDisc only within
the track being played.
● During random play, the unit cannot find the beginning
of any track which has been played.
● Repeat play lasts until you stop the unit.
– Advanced Playback –
Random play
RANDOM
RANDOM Repeat play of tracks in random order
Repeat play of all of the tracks
Repeat play of a single track
1
No display Normal playback
Useful Features
During playback, press the MODE button repeatedly to select the playback mode.
Press the ENTER/SYNC button.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
19
Advanced Recording
– Advanced Recording –
Useful Features
Playback sound-actuated recording
(Synchronized recording)
Recording automatically starts or pauses by detecting sound from the stereo system (Synchronized
recording).
1
2
3
4
Press the REC button.
Begin playback on the stereo system connected to this unit.
Press the REC LEVEL ( 5 or 4 ) button
to adjust the recording level
(analogue connection only).
Press the PAUSE button on the stereo system to enter the playback pause mode.
● Select the starting point for your recording and
press the PAUSE button.
5
6
Press the ENTER/SYNC button.
Begin playback on the stereo system.
Recording will begin automatically.
To interrupt recording:
● When the stereo system is stopped, the unit will enter
the synchro recording pause mode. When playback is
resumed, the recording will be resumed.
● If a silence lasts for 3 seconds or more, the recording
will be paused (Pause function does not work for
approximately 10 seconds after a recording starts).
● When the unit receives sound again, recording automatically starts.
● A new track number is created when the recording resumes.
To stop recording:
Press the • ■/:OFF button.
To write recorded contents on the MiniDisc
Press the • ■/:OFF button whilst in the stop mode.
20
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Advanced Recording : continued
1
When recording in long-play mode, the available
recording time will be doubled.
Long-play recordings can be replayed at double
speed, see page 19.
Press the MODE button whilst the recording is paused.
Stereo mode
Long-play mode
● “MONO” appears whilst in the long-play mode.
2
Start recording.
Notes:
● When the unit is stopped after a recording has been made
in this mode, the recording mode will return to the stereo
mode automatically.
● If input is from a stereo source, the sounds from the left
and right channels will be combined.
● Although the monitor sound you hear in the earphones
whilst recording is in stereo, recording will be monaural.
● MiniDiscs recorded in the monaural long-play mode may
not play on other MiniDisc players.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
– Advanced Recording –
Appears
Useful Features
Long-play recording (monaural recording)
21
Advanced Recording : continued
To start recording from the middle of a track
1
– Advanced Recording –
Useful Features
You can erase a portion of a track and make a new
recording.
● All of the tracks that follow the newly recorded track will
be erased.
2
During playback, press the 06 button at
the point where you want to begin recording.
Press the REC button.
● To cancel the operation, press the • ■/:OFF button.
3
Press the ENTER/SYNC button.
● All of the tracks and track names will be erased,
following the point where the playback is paused.
4
Press the 06 button.
● Recording will start.
Note:
● To keep a track after the point you want to make a new
recording, move the track and then make recording after that point.
(See “Editing a recorded MiniDisc”, page 39.)
22
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Advanced Recording : continued
Whilst recording, press the REC button at the
point where you want to create track numbers.
The track number will be increased by one.
Slide the accidental erase prevention tab, located
on the side of the MiniDisc, in the direction indicated by the arrow.
● The MiniDisc will then be protected against accidental
erasure.
● One track number will be created every time the REC
button is pressed.
● The SOUND button on the remote control can also be
used to create track numbers.
Recordable
Recording tracks as a single track
You can record several pieces of music as a single
track by disabling the auto marker function.
When a recording is paused or whilst recording…
Press the EDIT button.
Note:
● When making digital recordings using a CD player or an
MiniDisc player, track numbers will be created automatically regardless of the setting of the auto marker function.
Recording
prevented
To add a recording to such a MiniDisc, slide the accidental erase prevention tab back to its original position.
Helpful tip when attaching a label
When attaching a label to an MiniDisc cartridge, be sure to
note the following. If the label is not attached properly, the
MiniDisc may jam inside the unit and it may not be possible to remove it.
● If the label peels off or partially lifts
away, replace it with a new one.
● Do not put a new label on top of an
existing one.
● Attach the label only in the specified
location.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
– Advanced Recording –
You can create your own track numbers at any point.
To prevent recorded MiniDiscs from
being erased accidentally
Useful Features
To create your own track numbers
23
Advanced Recording : continued
● When recording, if a programmed playback is performed
– Advanced Recording –
Useful Features
About track numbers
1. Track numbers are created automatically during recording via the analogue connection when a silence
of 1 second or more is detected (Auto marker function). A series of tracks can be recorded as one by
disabling the auto marker function see page 23.
About 1
second
Silence
First
track
About sampling rate converter
Second
track
2. When recording from a CD or a MiniDisc using the
digital connection, track numbers will be created at
the same points as on the CD or MiniDisc (Synchro
marker function).
First track Second track Third track
Playback
side
Track A
Track B
Track C
First track Second track Third track
Recording
side
Track A
Track B
Track C
● Track numbers may not be created in proper places,
depending on the source to be recorded from, such as
signals with noise.
● The track numbers on the playback side may not match
the track numbers recorded on the MiniDisc.
24
Web-site: www.sharp.co.uk/support
by the source or playback is performed by selecting
tracks manually, the MiniDisc track numbers may not be
the same as on the source.
● Track numbers may not be created properly, depending
on the connected stereo system.
This unit incorporates a sampling rate converter meaning
it can record from digital radios or DAT tape recorders.
Note for digital recording
You can not copy a MiniDisc that you recorded from digital
inputs to another MiniDisc or DAT. It is prevented by the
SCMS (Serial Copy Management System). Recording from
analogue inputs is not affected.
Digital signals
Digitally recorded
MiniDisc
CD player,
MiniDisc
player,
etc.
Digital
connection
Help Line: 0990 274277 (office hours)
Cannot record
Digital
connection
Recording from a Microphone
2
3
4
Connect a stereo microphone to the MIC
IN socket.
Insert a recordable MiniDisc (page 11).
Press the REC button.
Press the REC LEVEL ( 5 or 4 ) button
to adjust the recording level.
Level meter indicator
0dB
4dB
● Adjust the recording level so that the maximum
sound volume from the source makes the reading
swing somewhere between –4 dB and 0 dB.
To the MIC IN
socket
5
Stereo microphone
(commercially available)
Press the 06 button.
● Recording will start.
To interrupt a recording
Press the 06 button whilst recording.
● To resume recording, press the 06 button again.
The track number will be increased by one each time
you interrupt a recording.
– Recording from a Microphone –
1
Useful Features
To record from a microphone
To stop recording
Press the • ■/:OFF button.
To write recorded contents on the MiniDisc
Press the • ■/:OFF button whilst in the stop mode.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
25
– Recording from a Microphone –
Useful Features
Recording from a Microphone : continued
Sound-actuated recording
(Mic Synchronized recording)
1
2
Press the REC button.
Press the REC LEVEL ( 5 or 4 ) button to adjust the recording level.
Level meter indicator
0dB
4dB
3
Press the ENTER/SYNC button to select
the recording sensitivity.
MIC SYNC H : Recording starts when the unit
detects –24 dB or more
(The unit can start recording from
quiet sounds).
MIC SYNC L : Recording starts when the unit
detects –12 dB or more.
4
About pause function
The unit automatically pauses when the microphone does
not pick up any sound for 3 seconds or more. (Pause function does not work for approximately 10 seconds after a
recording starts.) When the microphone picks up sound
again, recording starts automatically.
Notes:
● Whilst making a mic recording, do not connect anything
to the OPTICAL/LINE IN socket on the main unit.
● To use a microphone, be sure it is a plug-in-power type
microphone.
• When a plug-in-power type microphone is plugged
in, the main unit will provide power for the microphone’s operation.
• If a different type of microphone is plugged in, it may
not operate properly or it may cause the unit to malfunction.
● Insert the plug firmly. If you don’t, the recording will not
be made properly.
● Use a microphone with a 3.5 mm (1/8") diameter stereo
mini plug.
When a sound, such as person speaking,
is picked up by the microphone, recording
will begin automatically.
● If the unit starts recording too often from low unwanted
noises, set the microphone input to “MIC SYNC L”.
● Recording sensitivity can be changed whilst recording.
26
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Recording from a Microphone : continued
Changing intervals between tracks
1
When a recording is paused or whilst recording, press the EDIT button repeatedly.
(A new track number is
created every 5 minutes.)
(A new track number is
created every 3 minutes.)
During a mic manual recording
● Timed auto marks will be created every 5 minutes.
Track
number 1
Track
number 2
5 minutes
5 minutes
Track
number 4
5 minutes
During a mic synchro recording
If a silence lasts for 3 seconds or more, a timed auto mark
will be created 5 minutes after the previous mark is created.
: Track number which is created by the timed auto mark function.
: Track number which is created when a silence lasts for 3 seconds or more during synchro recording.
Track
Track
number 1 number 2
(A new track number is
created every 10 minutes.)
Track
number 3
Track
Track
number 3 number 4
Track
number 5
(No automatic track
numbers are created.)
● The interval between marks may vary slightly com-
2 minutes
5 minutes 1 minute
5 minutes
pared with the actual recording time.
2
Track numbers will be created automatically at regular intervals.
Useful Features
When recording from the microphone, track numbers will be created automatically at regular intervals (default setting: approximately every 5 minutes). During a mic synchro recording, the unit
pauses when a silence lasts for 3 seconds or more,
and creates a track number.
– Recording from a Microphone –
Example: Set to “5 minutes”.
Track intervals
Creating track numbers manually
Press the REC button whilst recording.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
27
Checking Displays
– Checking Displays –
Useful Features
To check the elapsed time and remaining
time of the track
To check the remaining recording time
and the total playing time
During playback, press the DISP button.
Whilst in the stop mode, press the DISP button.
Each time the button is pressed, the display will change as
follows:
Each time the button is pressed, the display will change as
follows:
Track number
Total number of
tracks
Track name
Disc name
Elapsed playback
time
Remaining
recording time
Remaining
playback time
Total playing time
Notes:
● If the disc name or the track name was not originally
recorded on the MiniDisc, “NO NAME” will be displayed.
● Remaining recording time will not be displayed with a
play-back only MiniDisc.
● Elapsed playback time and remaining playback time may
be different from the actual time.
28
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Checking Displays : continued
Whilst in the stop mode, press the 5 or
4 button to display the track number and
track name.
Track number
Track name
The remaining amount of battery level is shown
by the battery indicator (
) during operation.
How to read the battery indicator
When the battery
level is high
When the battery
level is very low
● When the battery is completely discharged, the battery
2
Press the DISP button to display the playing time for that track.
Playing time
● Each time the 5 or 4 button is pressed, the
playing time of the previous or next track will be
displayed.
indicator will flash. Recharge the battery or replace the
alkaline battery with a new one.
● When the battery has run completely out, “BATT EMPTY
(LoBATT)” will appear. Then, the power will be disconnected automatically.
Notes:
● If you use the battery which you stopped charging half” may appear. It does not mean that the batway, “
tery is completely charged.
● The battery indicator will not correctly display the remaining capacity for approximately 10 seconds after the power
has been turned on.
● When the AC adaptor or a separately available car adaptor is used, the battery indicator will not be shown.
● The number of bars shown in the battery indicator may
increase or decrease, depending on the operation being performed. This is normal.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
– Checking Displays –
1
Checking the remaining amount of
battery level
Useful Features
To display the playing time of an individual track
29
Battery Power
Charging the rechargeable battery
– Battery Power –
Useful Features
1
2
When the rechargeable battery is used for the first
time or when you use it after a long period of disuse,
be sure to charge it fully.
1
2
Lift the battery cover.
● Do not force the battery cover open too far.
3
Insert the rechargeable battery from the
(+) marked side.
● A rechargeable battery other than the one sup-
plied or the separately available one (AD-N70BT)
cannot be charged.
4
5
To the DC IN
5V socket
To wall socket
AC 230-240V,
50/60 Hz
30
Slide the battery cover as far as it will go
to the outside.
Web-site: www.sharp.co.uk/support
6
Close the battery cover.
Plug the AC adaptor into the wall socket,
and then insert the plug on the other end
into the DC IN 5V socket.
Press the :OFF/CHRG (•■ ) button.
● “
” will flash, and battery will begin charging.
(Refer to the next page for the charging time.)
Help Line: 0990 274277 (office hours)
Battery Power : continued
Using with the rechargeable or alkaline battery
To charge the battery fully, continue charging for
about 2 more hours.
In this case, you do not need to press the :OFF/CHRG
(•■ ) button. Even if the :OFF/CHRG (•■ ) button is
” will not appear.
pressed, “
Notes:
● This unit should only be used within the range of 0°C 40°C (32°F - 104°F).
● Charge the battery within the range of 5°C - 35°C (41°F - 95°F).
● Charging is completed when “
” does not blink when you
plug in the AC adaptor and press the :OFF/CHRG (•■ ) button.
● The unit can be left in the charging state after it is completed.
Caution:
● Use the specified battery AD-N70BT only. Do not charge
a battery (nickel-cadmium, alkaline, etc.) other than that
specified.
● Do not remove the outer cover of the rechargeable battery. It may cause heat generation, fire, or explosion.
● Do not dip the battery in water, do not dispose of it in a fire, and do not take it apart.
● If the rechargeable battery terminal is dirty, charging may
not start. In such a case, wipe off the dirt with a dry cloth.
● Do not disassemble the battery.
1
2
Disconnect the AC adaptor.
Insert the rechargeable battery or alkaline battery from
the (+) marked side.
● Use a commercially available
LR6, “AA” size alkaline battery.
Notes:
● Setting the volume level to “0” whilst recording with the
rechargeable or an alkaline battery reduces the battery
drain.
● When you do not use the unit for hours, remove the battery. (The battery drains gradually even when the power
is turned off.)
● Carry the battery in the supplied case.
● This unit can be used with the AC adaptor when the rechargeable or an alkaline battery is in the unit.
● After the rechargeable battery is charged or used, it will
get slightly warm. This is normal.
– Battery Power –
After about 3.5 hours have passed, “
” will go out.
The battery charging is about 90% complete.
Useful Features
About charging time
Caution:
● Do not use a nickel-cadmium battery.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
31
– Listening to a MiniDisc Through a Stereo System or a Car Stereo –
Useful Features
32
Listening to a MiniDisc Through a Stereo System or a Car Stereo
Listening through a stereo system
Listening through a car stereo
To the LINE INPUT sockets
Red:
To the right
Separately
available
car adaptor
(AD-CA20X)
White:
To the left
To the
socket
Separately available
cassette adaptor
(AD-CT14)
To the
socket
Connection cable
Notes:
● When recording with stereo system, eliminate the confirmation sound (page 33).
Otherwise, it will also be recorded.
● The recording will be made in the analogue mode.
● Character information will not be recorded.
Notes:
● Adjust the volume of both this unit and a car stereo.
● Do not operate this unit whilst you drive a car. It may
distract your attention and cause a traffic accident.
● Do not use any car adaptor except for the separately
available AD-CA20X.
● Remove the battery when you power the unit from the
car battery.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Changing Default Settings
1
With a MiniDisc inserted, press the MODE
button for 2 seconds or more. “SET UP”
will appear.
Auto play
You can make the unit not play automatically when
you insert a playback-only MiniDisc or an accidental
erasure protected MiniDisc.
Auto power save
● When you release the button, “BEEP ON (BEEP 1)”
or “BEEP OFF (BEEP 0)” will appear.
2
When the unit is used in a place exposed to much
vibration, sound skipping can be decreased by cancelling the auto power save function. (Battery will
drain faster.)
Press the 5 or 4 button to display the
menu. Then press the MODE button to
switch items.
[BEEP ON]
(BEEP 1)
[A-PLAY ON]
(autoPL)
[AUTO Psave]
(autoPS)
Beep sound
Auto play
Auto power
save
[BEEP ON] (*)
(BEEP 1)
[A-PLAY ON] (*)
(autoPL)
[AUTO Psave] (*)
(autoPS)
[BEEP OFF]
(BEEP 0)
[A-PLAY OFF]
(PL off)
[Psave OFF]
(PS off)
What is auto power save function?
Auto power save function automatically adjusts the sound
skip memory storage to be from 5 to10 seconds depending on playback conditions, this saves battery power.
If the MiniDisc unit is used in areas of much vibration it
may be necessary to fix the sound skip memory to 10 seconds “Psave OFF (PS off)” this will improve performance
under difficult conditions but uses more power. (When the
AC/car adaptor is used the 10 second mode is always used)
– Changing Default Settings –
You can eliminate the confirmation sound that beeps
when you press a button.
Advanced Features
Whilst in the stop mode ...
Beep sound
(*) indicates default setting.
3
Press the • ■/:OFF button.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
33
Titling a MiniDisc
– Titling a MiniDisc –
Advanced Features
Creating disc and track names
One disc name and up to 255 track names can be created
per disc (A maximum of 100 characters for the disc and
each track name and a total of 1,700 characters can be
entered).
1
Disc name
Track name
Whilst in the pause
mode, press the EDIT
button repeatedly to
select “DISC NAME”.
Whilst in the pause
mode, press the EDIT
button repeatedly to
select “TRACK NAME”.
5
Press the 5 or 4 button repeatedly to
select the letter.
Press the ENTER/SYNC button to enter it.
Position where the next letter will be entered
2
Press the ENTER/SYNC button.
Cursor
● The unit will enter the character input mode.
● The MiniDisc lid will be locked, to cancel the
6
7
To enter more letters, repeat steps 3 - 5.
When the name has been completely entered, press the EDIT button.
operation, press the • ■/:OFF button.
3
Press the DISP button repeatedly to select
the type of characters.
(Capital letters) (Lower-case letters) (Numbers and symbols)
● The first 3 characters in the group of the selected
characters will be displayed for about 1 second.
34
4
Web-site: www.sharp.co.uk/support
8
TOC will be displayed to write the updated
contents to the MiniDisc press the • ■/:OFF
button.
● You cannot remove the MiniDisc whilst TOC is
displayed. TOC will not disappear until the recorded contents have been updated.
Help Line: 0990 274277 (office hours)
Titling a MiniDisc : continued
Press the VOL + or VOL – button to move the cursor to the
character you want to erase, and then press the BASS
button.
1
2
To enter a space
Put the unit in the character input mode.
(Perform steps 1 - 2 on page 34.)
Press the VOL + or VOL – button to move
the cursor to the right of the character,
where you want to add a new character.
Press the VOL + button to move the cursor to the right.
3
Space
Select the character to add.
(Perform steps 3 - 4 on page 34.)
Characters (symbols)
Capital letters
A B C D E F G H
I
J
O P Q R S T U V W X Y Z .
,
o
b
c
d
e
f
g
h
i
j
p q
r
s
t
u
v w x
y
5
6 7
+ ,
l
z .
m n
,
/
!
:
#
<
k
Numbers and symbols
1
2
3 4
( )
% & '
> ? @ _
`
*
: indicates a space.
8 9
– .
0
/
Press the ENTER/SYNC button.
5
Press the EDIT button.
/
Lower-case letters
a
4
K L M N
"
;
$
=
6
– Titling a MiniDisc –
To add characters
Advanced Features
To erase a charactor
TOC will be displayed to write the updated
contents to the MiniDisc press the • ■/:OFF
button.
● You cannot remove the MiniDisc whilst TOC is
displayed. TOC will not disappear until the recorded contents have been updated.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
35
Titling a MiniDisc : continued
Before stamping
– Titling a MiniDisc –
Advanced Features
Stamping titles from another MiniDisc
Master MiniDisc operation
When there are 2 MiniDiscs on which the same tracks
are recorded, you can transfer the character information
(disc and track names) of the Master MiniDisc to another
MiniDisc (for stamping).
1. What is a master MiniDisc?
A recordable MiniDisc that contains tracks and character information.
(You can not transfer the information from a playback-only MiniDisc.)
1
Do not mistake the Master
MiniDisc for the target one.
2
3
Whilst in the stop mode, press the EDIT button repeatedly to select “NAME STAMP”.
Press the ENTER/SYNC button.
● To cancel the operation, press the • ■/:OFF button.
2. What is a MiniDisc for stamping?
A MiniDisc that contains the same tracks in the same
order as the master MiniDisc.
(Make sure that the total number of tracks of the
master MiniDisc and the one for stamping are the
same.)
Insert a Master MiniDisc.
4
5
Press the ENTER/SYNC button.
When the unit displays “CHANGE MD”,
remove the master MiniDisc.
● Remove it without turning off the power. Or, the
operation will be cancelled.
36
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Titling a MiniDisc : continued
7
Load a MiniDisc for stamping.
Press the ENTER/SYNC button.
Notes:
● If the total number of tracks on the master MiniDisc does
not match that on the MiniDisc for stamping, the unit will
display "Can't STAMP" and turn off the power.
If this happens, adjust the total number of tracks on the
newly recorded MiniDisc using the edit operation.
● Use a MiniDisc that was recorded by this unit to make
a MiniDisc for stamping. Character information may not
be transferred if you use a MiniDisc recorded by other
equipment. In such a case, enter at least one character for the disc name or the track names. You can transfer information once you record the TOC.
– Titling a MiniDisc –
6
Advanced Features
Operation of the MiniDisc for stamping
● The unit will finish recording the character infor-
mation and enter the stop mode.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
37
– Editing a Recorded MiniDisc –
Advanced Features
Editing a Recorded MiniDisc
To erase tracks one at a time
To erase all of the tracks at once
To divide a track
1 Start playing the track to
1 Whilst in the stop mode,
1 Start playing the track to
be erased, and press the
06 button.
press the EDIT button repeatedly to select “ALL
ERASE”.
be divided into two. Press
the 06 button at the point
where you want to divide
the track.
2 Press the EDIT button repeatedly to select “ERASE”.
2 Press the ENTER/SYNC
3 Press the ENTER/SYNC
● To cancel the operation, press
the • ■/:OFF button.
the • ■/:OFF button.
4 Press the ENTER/SYNC
button again.
peat steps 1 - 4.
Web-site: www.sharp.co.uk/support
3 Press the ENTER/SYNC
button.
● To cancel the operation, press
the • ■/:OFF button.
4 Press the ENTER/SYNC
● All of the tracks will be erased.
5 To erase other tracks, re38
3 Press the ENTER/SYNC
button again.
● The track will be erased.
peatedly to select “DIVIDE”.
button.
button.
● To cancel the operation, press
2 Press the EDIT button re-
Caution:
Once a track has been erased, it can
not be recovered.
Check the track number before erasing it.
Help Line: 0990 274277 (office hours)
button again.
● The track will be divided into
two tracks, and the unit will
pause at the beginning of the
second of the two new tracks.
To move a track
1 Start playing the last of
1 Play the track to be moved,
the two tracks to be combined, and press the 06
button.
and press the 06 button.
2 Press the EDIT button repeat-
2 Press the EDIT button repeatedly to select “MOVE”.
edly to select “COMBINE”.
3 Press the ENTER/SYNC button.
3 Press the ENTER/SYNC
button.
● To cancel the operation, press
the • ■/:OFF button.
4 Press the 5 or 4 but● To cancel the operation, press
ton to select the direction.
the • ■/:OFF button.
4 Press the ENTER/SYNC
button again.
5 Press the ENTER/SYNC
button again.
● The two tracks will be com-
bined, and the unit will be
paused at the beginning of the
combined track.
● The track will be moved, and
the unit will be paused at the
beginning of the track.
Web-site: www.sharp.co.uk/support
When a track has a name before dividing:
● The two new tracks will have the same
name. However, in the TOC FULL condition, the second track may not be named.
Total number of tracks that can be divided:
● Each disc can hold up to 255 tracks.
However, even if the number of assigned tracks has not reached 254, it
might not be possible to make any further divisions of tracks.
To combine two non-adjacent tracks:
● First, put the two tracks next to each
other in the order you want using the
MOVE function. Then combine them
using the COMBINE function.
When one or both tracks to be combined have a name:
● The first track name will be used. However, when the first track does not have a
name, the second track name will be used.
In the following cases, tracks may not
be combined.
● Tracks recorded by different inputs
cannot be combined.
Example:
- Digital recorded track and analogue
recorded track.
- Long play recorded track and stereo
recorded track.
● Tracks whose recording time is less
than 12 seconds.
Help Line: 0990 274277 (office hours)
– Editing a Recorded MiniDisc –
To combine tracks
Advanced Features
Editing a recorded MiniDisc : continued
39
Other Features and Caution
– Other Features and Caution –
References
Resuming auto play
Rechargeable battery
■ When you stop playback and replay the MiniDisc
without removing it, playback starts from the point
you stopped it.
Stopping
●
Stopped track
First track
Playing
●
■ Once you remove the MiniDisc, playback starts from
the first track.
Stopping
First track
●
Stopped track
Playing
●
■ The unit provides the following functions when you
use it with the separately available car adaptor (ADCA20X) (when the rechargeable or alkaline battery
is removed):
●
●
1. When you turn off the engine, the power of this unit
also turns off. (It may not work with some types of
cars.)
2. When you restart the engine, playback starts from
the beginning of the stopped track.
Stopping
First track
Stopped track
Playing
40
● A rechargeable nickel-metal hydride battery is the only
Web-site: www.sharp.co.uk/support
●
●
●
kind that can be used. Even if the battery is not used,
you should charge it at least once every three months
because of the special quality of this battery.
The rechargeable battery can be charged approximately
300 times.
When the operating time is reduced to about half the
normal amount of time, even after a full charge is performed, replace the battery with a new one (AD-N70BT).
When the battery is charged for the first time or is charged
after not being used for a long period, the operating time
may be shorter than normal. The battery life will recover
with normal use i.e. charging and discharging.
To avoid shortening the service life of the battery only
recharge the battery after it has been completely discharged.
If the rechargeable battery is used in a cold environment,
the operating time will be reduced.
Do not carry the battery in your pocket or a bag together
with metal objects (keys, coins, jewelry, etc.). The battery may short out and generate significant amounts of
heat.
Do not short-circuit the terminals as they will become
very hot and will damage the battery.
Do not drop or subject the battery to shock.
Do not insert objects (metal etc.) into the battery compartment of this product or into the rechargeable battery.
Help Line: 0990 274277 (office hours)
MiniDisc System Limitations
LIMITATIONS
“DISC FULL” or “TOC FULL” appears More than 255 tracks (maximum) cannot be recorded regardless of the reeven though the MiniDisc still has re- cording time.
cording time left.
If the MiniDisc is recorded or edited repeatedly or if it has scratches (recording skips scratched parts), you may not be able to record the maximum
tracks above.
The remaining recording time does not The unit does not count non-recorded portions that last 12 or fewer seconds
increase even though you erased tracks. to display the remaining recording time. The time may not increase even if
you erase short tracks.
The total of the recorded time and the One cluster (approximately 2 seconds) is the minimum unit for recording.
remaining time does not match the maxi- For example, a 3-second track uses 2 clusters (approximately 4 seconds).
mum recordable time.
Therefore, the actual recordable time may be shorter than the displayed
time.
Combine function does not work.
A MiniDisc on which recording and editing are repeated may not allow the
combine function.
Sound skips in fast reverse/forward.
One track is divided and recorded in separate places on a repeatedly recorded or edited MiniDisc.
Sound may skip.
References
SYMPTOM
– Minidisc System Limitations –
The unit may have the following symptoms whilst recording or editing. The unit is not out of order.
A track number is created in the middle A track number may be created if there are scratches or dust on the MiniDisc.
of a track.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
41
Error Messages
ERROR MESSAGES
MEANING
BATT EMPTY
● The battery is run down.
● Charge the rechargeable battery or replace the alka-
BLANK MD
● Nothing is recorded.
● Replace the disc with a recorded disc.
Can’t COPY
● You tried to record from a copy pro-
● Record using the analogue cable.
Can’t EDIT
hibited MiniDisc.
● A track cannot be edited.
● Change the stop position of the track and then edit it.
Can’t READ (*)
● The disc data cannot be read be-
Can’t REC
● Recording cannot be performed cor-
line battery (or use the AC adaptor for power).
(LoBATT)
– Error Messages –
(BLANK)
References
REMEDY
(Can’tC)
(Can’tE)
(Can’tS)
(Can’tT)
(Can’tU)
cause the disc is damaged.
● Reload the disc.
● Replace it with another recorded disc.
HOLD
● Re-record or replace it with another recordable disc.
rectly due to vibration or shock.
● Stamp function does not work.
● Check the number of tracks.
● Cannot save the TOC information ● Replace the disc with another recordable disc.
correctly to a MiniDisc. (A large portion of the disc has been damaged.)
● The disc is scratched.
● If the sound you hear is not right, record again.
● Replace the disc with another recordable disc.
● The disc is out of recording space.
● Replace it with another recordable disc.
● The microprocessor has reported a ● To have it repaired, go to the distributor where you
system fault and the unit is out of orpurchased the unit.
der.
● The unit is in the hold mode.
● Return the HOLD switch to its original position.
LOCKED
● You removed a MiniDisc whilst re-
(Can’tR)
Can’t STAMP
Can’t WRITE
(Can’tW)
DEFECT
(DEFECT)
DISC FULL
Er-MD (**)
(ErMD*)
(HOLD)
(Can’tLOCK)
● Turn off the power and remove the MiniDisc.
cording or editing.
( ) : Error messages seen on the remote control.
Number or symbol appears in (*) position.
42
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
Error Messages : continued
MEANING
REMEDY
NO DISC
● A disc has not been loaded.
● Load a disc.
NO SIGNAL
● Poor connection of the digital cable.
● No output signal comes out from the
● Connect the digital cable securely.
● If the portable CD player has a function to prevent sound
connected unit to playback.
skips, deactivate it.
● Playback with the connected unit.
● Replace it with a recordable disc.
PLAY MD
● You recorded on a playback-only
POWER ?
● Improper power is being supplied.
● Use one of the specified power sources.
● The write protection tab of a MiniDisc
● Move the write protection tab back to its original position.
● Replace it with a recordable MiniDisc.
(PLAYmd)
disc.
TEMP OVER
is set to the protected position.
● You tried to record on a playbackonly disc.
● Since a track number is currently
being located or updated, the unit
cannot accept your command.
● The temperature is too high.
TOC FORM (**)
● There is an error in the recording
PROTECTED
SORRY
(SORRY)
● Wait for a while and try the operation again.
● Turn off the power, and wait for a while.
(TEMP!)
signal.
● There is no space left for recording
character information (track names,
TOC FULL
disc names, etc.).
● The track has been protected from
Tr. Protect
being erased.
● A disc which contains data other than
? DISC
music was played.
(? DISC)
● There is an error in the signal recorded on the disc.
( ) : Error messages seen on the remote control.
Number or symbol appears in (*) position.
● Erase all of the tracks, and then record again.
(Tform**)
– Error Messages –
(noSIG.)
References
ERROR MESSAGES
● Replace it with another recordable disc.
● Edit the track with the device on which it was recorded.
● A disc which contains non-music data cannot be
played.
● Replace it with another recorded disc.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
43
Troubleshooting
Many potential “problems” can be resolved by the owner without calling a service technician.
If something seems to be wrong with this product, check the following before calling your authorised SHARP dealer or
service centre.
44
– Troubleshooting –
References
PROBLEM
CAUSE
The unit does not turn on.
●
●
●
●
●
No sound is heard from the earphones.
● Is the volume set too low?
● Is the remote control unit or the earphones plugged in?
● Are you trying to play a MiniDisc with data on it instead of a MiniDisc containing music?
When the operation buttons are
pressed, the unit does not respond.
● Is the unit in the hold mode?
● Is the battery exhausted?
● Is the remote control unit plug or the earphones plug inserted firmly?
Some sounds are skipped.
● Is the battery exhausted?
● Is the unit being subjected to excessive vibration?
The MiniDisc cannot be ejected.
● Has the track number or character information been updated on the disc yet?
● Is the unit in the recording or editing mode?
Recording and editing are impossible.
●
●
●
●
●
Web-site: www.sharp.co.uk/support
Is the AC adaptor disconnected?
Is the battery exhausted?
Is the unit in the hold mode?
Has condensation formed inside the unit?
Is the unit being influenced by mechanical shock or by static electricity?
Is the MiniDisc protected against accidental erasure?
Is the unit connected properly to the other equipment?
Is the AC adaptor unplugged or did a power failure occur whilst recording or editing?
Is the unit in the hold mode?
Is an optical signal being output from the stereo system?
Read the operation manual for the stereo system.
Help Line: 0990 274277 (office hours)
Troubleshooting : continued
Moisture condensation
If such a problem occurs, do the following:
1. Unplug the AC adaptor from the wall socket.
2. Remove the battery.
3. Leave the unit completely unpowered for approximately
30 seconds.
4. Plug the AC adaptor back into the wall socket and
reoperate the unit.
When the unit has condensation inside, the disc signals
cannot be read, and the unit may not function properly.
In the following cases, condensation may form inside the unit.
● Shortly after turning on a heater.
● When the unit is placed in a room
where there is excessive steam
or moisture.
● When the unit is moved from a
cool place to a warm place.
To remove condensation:
Remove the MiniDisc and leave the unit for approximately
1 hour. The condensation should evaporate and the unit
will work properly.
Maintenance
■ Cleaning
Cautions:
When the unit becomes dirty
Clean it with a soft cloth.
When the unit is excessively
dirty, use a soft cloth dampened
in water (external surfaces only).
● Do not use chemicals for cleaning (petrol, paint thinner,
– Maintenance –
When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
References
If trouble occurs
etc.).
It may damage the cabinet finish.
● Do not apply oil to the inside of the unit.
It may cause malfunctions.
Clean the plugs and the connecting socket.
If the plugs or sockets are dirty, noise may be heard.
Cleaning will prevent noise.
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
45
Specifications
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes
for product improvement without prior notice.
The performance specification figures indicated are nominal values of production units. There may be some deviations
from these values in individual units.
■ General
46
– Specifications –
References
Power source:
DC 1.2V:
Rechargeable Nickel-Metal Hydride battery
(AD-N70BT) x 1
DC 5V:
AC adaptor (AC 230 - 240V, 50/60 Hz)
DC 1.5V:
Commercially available, “AA” size (LR6), alkaline battery x 1
DC 4.5V:
Separately available car adaptor, AD-CA20X
(for cars with a 12-24V DC negative earth electrical system)
Power consumption: 7 W (AC adaptor)
Output
RMS; 20 mW (10 mW + 10 mW)
power:
(0.2% T.H.D.)
Charging
Approx. 3.5 hours (90 %)
time:
Approx. 5.5 hours (fully charged)
(When using the AC adaptor included with the unit)
Battery life:
When using the rechargeable
When using a commercially
battery (fully charged) inavailable, high capacity, “AA”
cluded with the unit
size (LR6), alkaline battery
Continuous recording:
Continuous recording:
Approx. 3 hours
Approx. 4.5 hours
Continuous play:
Continuous play:
Approx. 6.5 hours
Approx. 7 hours
● The continuous recording time is for analogue inputs when the
volume level is set to “VOL 0”.
● The continuous play time shows the value when the volume
level is set to “VOL 15”.
● The above values are the standard values when the unit is
charged and used at an ambient temperature of 20°C (68°F).
● The operating time when using an alkaline battery may be different, depending on the type and manufacturer of the battery,
and on the operating temperature.
Web-site: www.sharp.co.uk/support
Input sensitivity:
Recording level
MIC H
MIC L
LINE
Output level:
Reference input level
0.25 mV
2.5 mV
100 mV
Input impedance
10 k ohms
10 k ohms
20 k ohms
Specified
Maximum
Load
output
output level
impedance
—
10 mW + 10 mW
32 ohms
Earphones
250 mV (-12 dB)
—
10 k ohms
LINE
Dimensions:
Width:
99.9 mm (3-15/16”)
Height:
22.9 mm (29/32”)
Depth:
77.9 mm (3-3/32”)
Weight:
191 g (0.42 lbs.) with rechargeable battery
Input socket:
Line/optical digital, microphone
(powered by the main unit)
Output socket:
Earphones (impedance: 32 ohms)/remote
control unit
■ MiniDisc Recorder
Type:
Signal readout:
Audio channels:
Portable MiniDisc recorder
Non-contact, 3-beam semi-conductor laser pick-up
Stereo 2 channels/monaural (long-play mode)
1 channel
Frequency response: 20 – 20,000 Hz (± 3 dB)
Rotation speed:
Approx. 400 – 900 rpm
Error correction: ACIRC (Advanced Cross Interleave ReedSolomon Code)
Coding:
ATRAC (Adaptive Transform Acoustic Coding),
24-bit computed type
Recording method: Magnetic modulation overwrite method
Sampling frequency:44.1 kHz (32 kHz and 48 kHz signals
are converted to 44.1 kHz, and then recorded.)
Wow and flutter: Unmeasurable (less than ±0.001% W. peak)
Help Line: 0990 274277 (office hours)
Editing
Connections ......................................... 12, 13
Insert a MiniDisc ......................................... 11
Disc name .................................................. 34
Stamping titles ...................................... 36, 37
To add characters ....................................... 35
To combine tracks ...................................... 39
To divide a track ......................................... 38
To erase a character .................................. 35
To erase all of the tracks at once ............... 38
To erase tracks one at a time ..................... 38
To move a track .......................................... 39
Track name ................................................ 34
Recording
Long-play recording
in monaural mode .................................... 21
Recording from a Microphone .................... 25
Sound-actuated recording
(Synchronized recording) ..................... 20, 26
To start recording
from the middle of a track......................... 22
Playback
Bass control ............................................... 17
Random play .............................................. 19
Repeat play ................................................ 19
To play at double speed ............................. 19
Volume control ........................................... 17
Explanation
Function
Battery level ............................................... 29
Battery power ....................................... 30, 31
Default settings .......................................... 33
Hold function ................................................ 9
Remaining playback time ........................... 28
Remaining recording time .......................... 28
Total playing time ....................................... 28
– Index –
Preparation
References
Index
Auto mark ............................................. 23, 27
Erase-prevention tab .................................. 23
Resuming auto play ................................... 40
TOC ............................................................ 15
Track numbers ........................................... 24
Web-site: www.sharp.co.uk/support
Help Line: 0990 274277 (office hours)
47
TERMS OF GUARANTEE
Subject to the terms listed below, Sharp Electronics (U.K.)
Ltd. (hereinafter called “the Company”) guarantee to provide for the repair of, or at its option replace this Sharp
Equipment, or any component thereof, (other than batteries), which is faulty or below standard, as a result of
inferior workmanship or materials.
The conditions of this guarantee are:
1. The guarantee shall only apply to defects which occur
within one year from the date of purchase, provided
that this equipment is sent to the repair address within
this period.
2. This guarantee covers equipment intended for private
domestic use only. This guarantee does not apply to
equipment used in the course of a business, trade or
profession.
3. The guarantee does not cover MiniDiscs or batteries.
4. This guarantee does not cover any faults or defects
caused by accident, misuse, fair wear and tear, neglect,
tampering with the equipment, or any attempt at adjustment or repair other than by a Service Facility appointed by Sharp.
5. In the unlikely event of a defect occuring, the product
must be returned to the Company’s repair centre with
proof of purchase. A postage paid label and a fault report form are supplied with the product for this purpose.
It is your responsibility to ensure that the packaging is
adequate, and to obtain proof of posting.
Further details of the repair service, which is available
after the guarantee period on a chargeable basis, and
additional report forms and labels can be obtained by
telephoning 0870 738 0000.
6. No person has any authority to vary the terms or conditions of this guarantee.
7. This guarantee is offered as an additional benefit to
the consumer’s statutory rights and does not affect
these rights in any way.
SHARP ELECTRONICS (U.K.) LTD.
Sharp House, Thorp Road, Newton Heath, Manchester, M40 5BE
SHARP CORPORATION
TINSE0325AWZZ
A0006.TO