Download Sangean DT-110 - 2 User manual

User Manual
DT-110
1
11
DBB
On
Off
12
Vol.
13
Lock
14
2
3
4
TUNING
DBB
FM STEREO/AM
PLL SYNTHESIZED
RECEIVER
DT 110
BAND
MO./ST.
5
6
7
8
9
10
2
LOCATION OF CONTROLS
To insure proper operation, please familiarize yourself with these instructions before using your new
receiver.
1
. On/Off button
2
. LCD display
3
. Tuning Control Down
4
. Tuning Control Up
5
. Battery Compartment
6
. Memory Button
7
. Memeory Recall button
8
. Priority Station Recall
9
. FM Stereo/Mono button
10 .
11
Band selection button
. Earphone Jack
. DBB (Deep Bass Booster) On/Off
13
. Volume Control
14
. Lock Switch
3
DISPLAY ICONS
1
2
4
3
M
P
ST
FM
Mhz
Khz
AM
AUTO MEMO SCAN
5
6
7
8
9
1 FM Stereo indicator
2 System lock
3 Low battery indicator
4 Memory Presets
5 Band Selected
6 90 minutes auto shut off
7 Frequency
8 Auto Scan /Memory Scan status
9 Frequency unit
4
B AT T E R Y I N S TA L L AT I O N
The battery cover is located on the back of the unit.
Slide the cover in the direction of the arrow to gain
access to the battery compartment 5 . Insert 2
AAA (UM-4) batteries into the compartment. Make
sure that the batteries are positioned in accordance
with the diagram indicated. Replace cover.
Note:
(1) During radio listening , radio will turn itself off
when the battery power becomes too low. A low
battery indicator will appear on the display for
1.5 seconds (you may not notice this ) indicating
weak batteries and replacement is necessary.
(2) During the low battery status, if you press the
POWER button, Radio won't turn it on but
appear with low battery indicator to remind the
battery power is low and needed for battery
replacement.
(3) During battery replacement, turn off the power
and make sure the lock switch is in the locked
position. This will prevent any memory presets
from being lost during battery replacement.
5
ANTENNA/EARPHONE USE
I n s e r t i n g t h e e a r p h o n e i n t o t h e e a r p h o n e j a c k 11 .
The cord connecting the earphone to the receiver
acts as an antenna during FM reception and should be extended as much as possible to increase
F M s e n s i t i v i t y.
A b u i l t - i n F e r r i t e B a r An t e n n a i s p r o v i d e d f o r AM
reception and it is only necessary to rotate the radio
f o r m a x i m u m s i g n a l s t r e n g t h d u r i n g AM l i s t e n i n g .
VOLUME CONTROL
A d j u s t v o l u m e c o n t r o l 13 t o a d j u s t t h e r e q u i r e d
listening volume.
TUNING THE RADIO
Band
Freq uency
Antenna
AM 520-1 710 kHz
FM
Intern al/Rotate radio for best
recep tion.
87.50-108 MHz External/Make sure the ear-
6
Pho ne is inserted into earphone jack.
A . APS (auto scan and auto preset)
This radio equips with APS device to have auto
scan and auto preset function. Among the many
conveniences offered by this feature it is especially useful for the traveler who can automatically
find all the local stations in any strange city he
may travel to with just the push of two buttons.
Tu rn on the radio by pressing On/Off button 1 ,
connect earphone to the earphone jack, select
required band by pressing band selection button
10 , t h e n p r e s s T u n i n g C o n t r o l U p 4 a n d D o w n
3 button at the same time for more than 2 seconds
until LCD display shows 'AUTO SCAN' .
The receiver will scan from the low frequency of
the selected AM or FM band and auto memory
the stations it can find until memory is full. i.e. 15
memory stations on FM band or 6 memory stations
7
o n AM b a n d . W h e n AP S c o m p l e t e s , i t w i l l a p p e a r
t h e f i r s t r a d i o s t a t i o n i t f i n d s . To r e c a l l t h e s t a t i o n s ,
p l e a s e r e f e r t o M e m o r y Tu n i n g ( s t a t i o n r e c a l l )
descri bed later.
B . 90 minutes auto shut off device
For saving battery power , this radio is designed
to auto shut off after 90 minutes operation, LCD
displa y shows
F o r c o n t i n u i o u s l i s t e n i n g i f n e c e s s a r y, p r e s s i n g
ON/Off button 1 for more than 2 seconds until LCD
displa y
disa ppears
C . Scan tuning
T ur n o n t h e r a d i o b y p r e s s i n g O n / O f f b u t t o n 1 ,
s e l e c t AM o r F M b a n d b y p r e s s i n g B a n d S e l e c t e d
b u t t o n 10 , t h e n p r e s s a n d h o l d t h e T u n i n g
Contr ol Up 4 or Down 3 for more than 1/2 second .
The radio will scan all the frequencies in that band
and will stop automatically when a radio station
is found.
8
D . M a n u a l Tu n i n g
T ur n o n t h e r a d i o b y p r e s s i n g O n / O f f b u t t o n 1 ,
s e l e c t AM o r F M b a n d b y p r e s s i n g B a n d S e l e c t e d b u t t o n 10 . D e s i r e d s t a t i o n m a y b e s e l e c t e d
by pressing the Tuning Control 3 or 4 interm ittently until the desired station is reached. Or
p r e s s i n g a n d h o l d i n g t h e Tu n i n g C o n t r o l u n t i l t h e
desired station is reached.
E . M e m o r y Tu n i n g ( s t a t i o n p r e s e t )
T ur n o n t h e r a d i o b y p r e s s i n g O n / O f f b u t t o n 1
S e l e c t AM o r F M b a n d b y p r e s s i n g B a n d S e l e c t e d b u t t o n 10 . T u n e t o t h e d e s i r e d s t a t i o n u s i n g t h e M a n u a l o r S c a n Tu n i n g m e t h o d s a s d e s cribed prior. When the desired station is reached and indicated in the LCD display 2 ,press
the Memory Button 6 . AM will flash in the
LCD display and also a suggested number of
memory position .During its flashing, select the
9
d e s i r e d m e m o r y p o s i t i o n b y p r e s s i n g Tu n i n g C o n trol 3 or 4 to the desired memory position,
then press Memory button 6 again. 'M' will stop
flashing indicating station memory being done.
Note : No matter you press Memory Button 6
or Memory Recall button 7 , if the number digit is flashing which indicates the flashing number station has been memoried.
It will replace previous memory station, if
you press Memory Button at this time.
Yo u m a y s t o r e a t o t a l o f 1 5 . s t a t i o n s i n t h e F M
band and 6 stations in the AM band plus 3 favor i t e s t a t i o n s a s p r i o r i t y d e s c r i b e d l a t e r.
If the memory is full , when press the Memory
button 6 , LCD display will appear FUL.In this
case, if you still like to memory the required station. Press the Memory button again, the radio
will memory the station by force and replace M15
10
o n F M b an d a nd M 6 o n A M b an d .
F . Prior ity
To st ore yo ur fa vo rit e st ati on s so th at yo u may
re call th e st ation s in a more easy w ay.
Whe n th e de sir ed st ati on s ar e fo un d by th e tu ni ng meth od s de scr ibe d ab ov e. Pr ess th e memory butt on 6 , then Prio rit y stat ion butt on 8 . AP
w ill fl ash in th e LC D di sp lay an d also a su gg est ed nu mb er of memory po sit ion . D uri ng P is fl ash ing , se lect th e de sir ed memory po sit ion by pr essi ng Tu nin g Con tro l 3 or 4 to the des ire d mem ory po sit ion , th en pr ess M emory bu tto n 6
ag ain . P w ill st op fl ash ing in dic ating pr ior ity st ati on
m emory be ing do ne .
The ra dio ca n al low m ax imum 3 fa vo rit e st ati on s.
G . Me m o r y Tu n i n g ( s t a t i o n re ca ll )
Tu r n o n t he r ad i o b y p r e s s i n g O n / O f f b u t t on 1
S e l e ct A M o r F M b an d b y p r e s s i n g b an d s e l e ct 11
e d b u t t o n 10 t h e n M e m o r y R e c a l l b u t t o n 7
Select the required memory station by pressing
Tuning Control 3 or 4 , LCD display Mand
memory digit will flash . When the required station is found, press Memory Recall button 7 again, LCD M and memory digit will stop flashing.
For priority stations recall, simply turn on the radio by pressing On/Off button 1 then pressing
Priority station button 8 . Select the required
Priority station by pressing priority station button
again.
If there is no memory station or priority station,
while you press Memory Recall button or Priority button , LCD display will show ME (memory
empty) or PE (priority station empty).
H . M E M O RY D e l e t e
If the memory is full or you like to delete the me12
mory stations .Recall the memory stations by pressing Memory Recall buttons 7 . Press Memory button 6 for more than 2 seconds untill LCD
display DEL flashing, press Memory button 6
again, the recall memory station is then deleted.
I . Memory Scan
To s c a n t h e m e m o r y s t a t i o n s , p r e s s M e m o r y r e call button for more than 2 seconds until LCD display MEMO SCAN appears, the radio will scan
the memory stations up and stops for a few seconds for you to pick up the required memory stations. When the required memory station is found.
Pres s Memory Recall button 7 twice to stop
Mem ory Scan.
J . Memory Exchange
For editing your memory stations, you may exchange the memory stations.
13
E x a m p l e : To e x c h a n g e M e m o r y s t a t i o n 2 w i t h
Memo ry station 4.
Recall Memory station 2 by pressing Memory
Recal l button 7 , press Memory button 6 then
Tun ing Control UP 3 butt on to the required Memory station 4, then press Memory button 6
again Memory station 2 and Memory station 4
now is exchanged.
K. Mono button
The radio is designed to receive FM stereo broadcasts with earphone connected to the earphone
j a c k 11 F o r w e a k F M s t a t i o n , p r e s s M o n o b u tton to get better reception.
L. Change AM band tuning step
F o r N o r t h e r n Am e r i c a n c o u n t r i e s ( C a n a d a a n d
U S A ) a n d s o m e S o u t h Am e r i c a n c o u n t r i e s , AM
14
tuning step is 10 kHz. On other countries is 9
kHz.
To change AM band tuning step, please follow
below steps.
1. change AM band tuning step from 9 kHz to
10kHz.
Turn off the power by pressing On/Off button
1 , press Tuning Control button Up 4 continuously then turn on the power by pressing
On/Off button again. Release the buttons the
AM tuning step will now change to 10 kHz.
2. change AM band tuning step from 10 kHz to
9 kHz
Turn off the power by pressing On/Off button
1 , press Tuning Control button Down 3
continuously and then turn on the power by
pressing On/Off button again. Release the buttons, the AM tuning step will change to 9 kHz.
15
M . Lock Switch
To prevent accidential changing of any of the radio settings, move the Lock Switch 14 to up position, LCD display
icon will appear. To release, simply move the switch to its down position.
It is important to make sure Lock Switch is in its
down position when radio is to be operated , as
radio is completely inoperative until Lock Switch
is released.
If the radio is not to be used for any extended period of time battery power savings may be realized by setting Lock Switch to On position
during storage.
SPECIFICATIONS
Type : FM stereo (via stereo earphones)
AM standard (mono)
16
Earphone Jack : 3.5 mm mini-plug
32 ohm impedance (stereo)
Output Power : 5 mW(10% THD) via earphone.
External Power : Earphone
AM 30 mA
FM 40 mA
Batteries : 3 Volts , AAA size (UM-4)X 2
Dimension ( WXHXD ) in mm : 95 x 60 x 20
Weight : 90g without batteries.
MAINTENANCE
1. Keep the radio dry. If it does get wet , wipe it immediately. Liquids may contain chemicals that
can corrode electronic circuitry.
17
2.Use and store your radio only in normal temperature environments. High temperature can shorten the life of electronic devices, damage batteries and melt plastic parts.
3. Handle the radio gently and carefully. Dropping
it can damage circuit boards and cases and render it defective.
4. Keep the radio away from dust and dirty.
5. Wipe the radio with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents
or strong detergents.
6. Use only fresh batteries of the recommended size and type. Always remove old or weak batteries as they can leak and destroy electronic components and circuitry.
7. Modifying or tampering with the radio intemal
components can cause a malfunction and will
void the product's warranty.
18