Download Channel Plus SVS-52 Specifications

O
O
Specifications: typical @ 25 C ± 5 C
Inputs
Video
performance
RS-232
Power supply
Physical
S-video, video, audio
gain
video level
audio level
video bandwidth
crosstalk (0 - 4MHz)
pin out
protocol
model number
output current
output voltage
input power
power consumption
height
width
depth
weight
5 inputs X 1 out
1.0 nominal (2 ports)
1 Vp-p @ 75
1 V rms @ 47k
<0.1db (0 - 4MHz)
>70 dB
2 TX, 3 RX, 5 GND
PERFORMANCE MULTI-ROOM VIDEO
9600 buad, 8 bit, 1 stop, no parity
350-103
600mA
15 VDC
105-125 VAC
8 watts typical
4.4 cm (1.75 in)
43.2 cm (17 in)
16.5 cm (6.5 in)
1.19 kg (2 lbs 10 oz)
Installation Manual
SVS-52
o
ide eo
S-v vid
IR
1
2
3
4
5
select
auto/manual
learn
display
Five Input Video
Audio Switcher
Warranty
Multiplex Technology, Inc. warrants this product to be free from defects in
materials and workmanship for a period of one year from the date of
purchase or MTI will repair, or at its option, replace the defective product.
To obtain warranty service, call MTI for a return material authorization
(RMA) number and return the product prepaid to Multiplex Technology,
Inc., 3001 Enterprise Street, Brea, CA 92821, Attention: Customer
Service. Please put the RMA number on the outside of the carton.
Any implied warranty arising from the sale of the product including implied
warranties of merchantability and fitness for purpose are limited to the
warranty stated above. MTI shall not be responsible for losses or damages
or expenses, whether direct, consequential or incidental arising from the
use of or the inability to use this product. Some states do not allow
limitations on how long the implied warranty lasts or the exclusion or
limitation or incidental or consequential damages, so the above limitations
and exclusions may not apply to you. This warranty gives you specific
legal rights, and you may have other rights which may vary from state to
state.
Model
SVS-52
This device complies with the FCC's Part 15 Rules. Any
change or modification to this device without the permission
of Multiplex Technology, Inc. may void the user's authority to
operate this equipment.
3001 Enterprise Street,
600-238 Rev. A
Multiplex Technology, Inc., Brea, CA 92821
Brea,
CA
92821-6213,
U.S.A.
714-996-4100 * 800-999-5225 * FAX 714-996-4900 * www.channelplus.com
SVS-52 contents:
FRONT PANEL CONTROLS:
CONNECTIONS:
- SVS-52 audio/video switcher
- SVS-52RC remote control
- 15VDC/600mA power supply
4
2
4
5
select
auto/manual
learn
display
input 5
2
OUTPUT
1 3
INPUTS
1
L R
L R
OUTPUT
3
2
OPTICAL
1
4
OPTICAL
3
INPUTS
1
OPTICAL
RS-232
OUTPUT
3
2
MOUNTING
The SVS switchers can be mounted in standard 19” racks by attaching the included
mounting ears. Remove the rubber feet on the bottom of the unit to ensure clearance
when inserted into a rack.
3
L R
-23
POWER FAILURE
The SVS-52 will remember all settings when the power fails. When power resumes, the
SVS-52 will power up in the same state as when power was removed - all front panel
settings and IR learning will be remembered.
1
L R
4
2
RS
FRONT PANEL INPUT
Input 5 on the SVS-52 is available on the front panel for connecting video cameras or
game consoles. Its operation is the same as the other four inputs.
3
INPUTS
4
L R
L
ITA
DIG IO T
D
AU TPU
OU
L
ITA
DIGDIO
S
AUPUT
IN
FRONT PANEL BRIGHTNESS
The front panel light intensity can be changed by pressing the display button on the front.
Each button press selects one of four different brightness levels including turning the panel
off completely.
3
4
1
4
2
L R
OG
AL
ANDIO T
AU TPU
OU
OG
AL
ANDIO
S
AUPUT
IN
AUTO DETECTION
When the auto detection LED is on, the SVS-52 will automatically search all five video
inputs to find the active video signal. If this feature is off, the user must select which input
to view manually.
1
OUTPUT
2
2
EO T
VIDTPU
OU O
E
VIDUTS
INP
5
S-VIDEO/COMPOSITE SELECTION
Press and hold the select button for two seconds to toggle between S-video and composite
mode. This selection is remembered for each input. Both S-video and composite outputs
will show the selected type. For example, if S-video is selected for input 2, it will be
available on both the S-video outputs and the composite outputs. The SVS-52 makes the
conversion between S-video and composite and composite to S-video with an active comb
filter circuit.
3
INPUTS
O
IDE T
S-VTPU
OU DEO
I S
S-V
UT
INP
UT
INP
SS
NE
HT
IG T
BRJUS N
AD AR
LE
IR
TO T
AUTEC /
DE DEO ITE
I OS
S-VMP T
COLEC
SE
OW
ND
WI
T
ON
FRNELHES
PA ITC
SW
IR
VIDEO SELECTION
Select the desired output by pressing one of the five buttons on the front of the unit. The
unit will show which input is selected by an LED over each button.
4
1
A N A LO G A U D I O
3
2
VIDEO
2
!
POWER
15VDC
600mA
S -V I D E O
1
IR
2 4
SVS-52
o
ide eo
S-v vid
-2 AAA batteries
-Product manual
- Mounting ears & screws
D I G I TA L A U D I O
The ChannelPlus SVS-52 is a five input audio/video selector. The SVS-52 has
inputs for S-video, composite video, analog audio and digital audio. The selected
video output is available on two separate but equal outputs. The SVS-52 also has
video convertion for viewing S-video on composite or viewing composite video on Svideo. A remote control is included for easy input selection.
IR OPERATION
The SVS-52 can be controlled via the included remote control. The remote can be used to
control three different switchers (using buttons A, B and C). Your unit is set at the factory
for unit A. Make sure you press “A” on your remote before using it. Press buttons 1
through 5 to select an input. Pressing a number button twice quickly will toggle the unit
between S-video and composite (this is the same function as pressing select on the front
panel). The remote can also be used to toggle the auto detect feature.
IR LEARNING - INPUT SELECT AND AUTO DETECT
To use another IR remote with the SVS-52, press and hold the learn button for three
seconds. The learn LED will flash to indicate the SVS-52 is in learn mode. Then press an
input button to be learned. The LED will light for that input. Point the remote at the IR
window on the front of the SVS-52. Press and hold the desired key on the remote for two
seconds then release. The LED for that switch will go out indicating that the code has been
learned. If the light does not go out, check the remote and try again. Press another SVS52 button to repeat the process for all input selects and auto detect. When finished, press
the learn button to exit the learn mode. The learn LED will stop flashing. The included
remote will no longer function after programming with another remote. To reactive the
remote, follow the above steps to relearn.
MULTIPLE SVS-52 UNITS WITH THE IR REMOTE
The included remote contains three separate codes sets to allow control of up to three
SVS-52 units. The SVS-52 is set at the factory for unit A. To control a second SVS-52,
press B on the remote and teach the unit all six buttons. Use C for a third unit. Now the
remote can control three separate units. Just press A, B or C before pressing the inputs
buttons to select which unit to control.
NOTES ON DIGITAL AUDIO INPUTS/OUTPUTS
Inputs 1 and 3 on the SVS-52 have TOSLINK connectors in addition to the coax digital
inputs. Inputs 1 and 3 can use either TOSLINK or COAX but not both. If both TOSLINK
and COAX connectors are used, the TOSLINK connector input will be ignored (even if no
active signal is present on the COAX input). There are two COAX outputs and one
TOSLINK output - all three are active regardless of the type of digital input used. The SVS52 automatically converts digital inputs to both COAX and TOSLINK outputs.
3