Download Craftsman 917.379300 Owner`s manual
Transcript
Owner's Manual CRAFTSMAN+ 6.6 HORSEPOWE 22" EAR DISCHARGE POWER P LED ROTARY LAW MOW Model No. 917.379300 o o o ° ° • Safety Assembly Operation Maintenance Espahol Repair Parts CAUTION'. Read and follow all Safety Rules and Instructions before operating this equipment Sears, Roebuck and Co., Hoffman Estates, IL 60179 -_1 Warranty Safety Ru_es Assembly Operation Maintenance Schedule Maintenance LIMITED TWO YEAR WARRANTY 2 2 4 6 10 10 Product Specifications Service and Adjustments Storage Troubleshooting Repair Parts Parts Ordering ON CRAFTSMAN POWER 11 14 !5 16 33 BackCover MOWER For two years from date of purchase, when this Craftsman Lawn Mower is maintained, lubricated, and tuned up according to the operating and maintenance instructions in the owner's manual, Sears will repair free of charge any defect in material or workmanship. If this Craftsman Lawn Mower is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This Warranty does not cover: • Expendable items which become worn during normal use, such as rotary mower blades, blade adapters, belts, air cleaners and spark plug. • Repairs necessary because of operator abuse or negligence, including bent crankshafts and the failure to maintain the equipment according to the instructions contained in the owner's manual Warranty service is available by returning the craftsman power mower to the nearest sears service center/department in the united states. This warranty applies only while this product is in use in the united states° This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., D/817 WA, HOFFMAN ESTATES, ILLINOIS 60179 TRAINING: ° Read this operator's manual carefully. Become familiar with the controls and know how to operate your mower properly, Learn how to quickly stop mower. ° Do not allow children to use your mower, Never allow adults to use mower without proper instructions, ° Keep the area of operation clear of all persons, especially small children and pets. • Use mower only as the manufacturer intended and as described in this manual, o Do not operate mower if it has been dropped or damaged in any manner. Always have damage repaired before using your mower, ° Do not use accessory attachments that are not recommended by the manufac- turer, Use of such attachments may be hazardous. o The blade turns when the engine is running° PREPARATION" ° Always thoroughly check the area to be mowed and clear it of all stones, sticks, wires, bones, and other foreign objects° These objects ,Mtl be thrown by the blade and can cause severe injury. ° Always wear safety glasses or eye shields when starting and while using your mower. ° Dress properly. Do not operate mower when barefoot or wearing open sandals. Wear only solid shoes with good traction when mowing° o Check fuel tank before starting engine. Do not fill gas tank indoors, when the engine is running or when the engine is hot.Allowthe engineto coolfor several minutesbeforefillingthe gas tank.Clean off any spilledgasolinebeforestartingthe engine. Always makewheel heightadjustments beforestartingyour mower.Never attemptto dothis whilethe engineis running. Mowonly in daylightor goodartificial lighL OPERATION: o Keepyour eyes and mindonyour mower andthe areabeing cut. Do not let other when changing directionsmaintain good footing_ o Never operate your mower without proper guards, plates, grass catcher or other safety devices in place. MAINTENANCE AND STORAGE: • Check the blade and the engine mounting bolts often to be sure they are tightened properly. o Check all bolts, nuts and screws at frequent intervals for proper tightness to be sure mower is in safe working condition. o Keep all safety devices in place and working. o To reduce fire hazard, keep the engine free of grass, leaves or excessive grease and oil. • Check grass catcher often for deterioration and wear and replace worn bags. Use only replacement bags that are recommended by and comply with specifications of the manufacturer of your mower. ° Always keep a sharp blade on your mower. o Allow engine to cool before storing in any enclosu re. o Never store mower with fuel in the tank inside a building where fumes may reach an open flame or an ignition source such as a hot water heater, space heater, clothes dryer, etc. interests distract yOUo • Do not mow wet or slippery grass. Never run while operating your mower. Always be sure of your footing -- keep a firm hold on the handles and walko o Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times. • Always stop the engine whenever you leave or are not using your mower, or before crossing driveways, ,walks, roads, and any gravel--covered areas. ° Never direct discharge of material toward bystanders nor allow anyone near the mower while you are operating it. ° Before cleaning, inspecting, or repairing your mower, stop the engine and make absolutely sure the blade and all moving parts have stopped° Then disconnect the spark plug wire and keep it away from the spark plug to prevent accidental starting. • Do not continue to run your mower if you hit a foreign object. Follow the procedure outlined above, then repair any damage before restarting and operating you mower. • Do not change the governor settings or overspeed the engine. Engine damage or personal injury may result. ° Do not operate your mower if it vibrates abnormally. Excessive vibration is an indication of damage; stop the engine, safely check for the cause of vibration and repair as required. ° Do not run the engine indoors. Exhaust fumes are dangerous. , Never cut grass by pulling the mower towards you. Mow across the face of slopes, never up and down or you might lose your footing° Do not mow excessively steep slopes. Use caution when operating the mower on uneven terrain or CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. 3 _J_ These accessories were available when this lawn mower was produced. They are also available at most Sears retail outlets and service centers, Most Sears stores can also order repair parts for you, when you provide the model nurrber of your lawn mower. Some of these accessories may not apply to your lawn mower. LAWN MOWER PERFORMANCE t _f 4_\ CLIPPING DEFLECTOR FOR REAR DISCHARGE LAWN MOWERS GRASS CATCHERS FOR REAR DISCHARGE LAWN MOWERS MULCHER KITS FOR SIDE DISCHARGE GRASS LAWN CATCHERS MOWERS _l GAS CANS LAWN MOWER MAINTENANCE II .......... :........ MUFFLERS BELTS I AIR FILTERS SPARK PLUGS SLADES BLADE ADAPTERS IMPORTANT: This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. Safety standards require operator presence controls to minimize the risk of injury. Your unit is equipped with such controls. Do not attempt to defeat the function of the operator presence controls under any circumstances° Read these instructions and this manual in its entirety before you attempt to assemble or operate your new lawn mower. Your new lawn mower has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. All parts such as nuts, washers, bolts, etc., necessary to complete the assembly have been placed in the parts bag. To ensure safe and proper operation of your lawn mower, all parts and hardware you as- WHEELS ENGINE OIL semble must be tightened securely. Use the correct tools as necessary to ensure proper tightness, TO REMOVE LAWN MOWER FROM CARTON Remove mower loose parts included with Cut down two end corners of carton and lay end panel down flat. Remove all packing materials except padding between upper and lower handle and padding holding operator presence control bar to upper handle. Roll lawn mower out of carton and checkcarton thoroughlyforadditional loose parts. 4 HOW TO SET UP YOUR LAWN TO INSTALL ATTACHMENTS MOWER TO UNFOLD HANDLE IMPORTANT: Unfold handles carefully so as not to pinch or damage control cables. o Raise handles until lower handle section locks into place in mowing position. o Remove protective padding, raise upper handle section into place on lower handles and tighten both handle knobs. ° Remove handle padding holding operator presence control bar to upper handle. o Your lawn mower handle can be adjusted for your mowing comfort. Refer to "Adjust Handle" in the Service and Adjustment section of this manual. "Your lawn mower was shipped ready to be used as a mulcher. To convert to bagging or discharging: • Open rear door and remove mulcher plug. Store mulcher plug in a safe place. o You can now install catcher or optional clipping deflector. o To return to mulching operation, install mulcher plug into discharge opening of Operator presence control bar Upper handle Lift up Lower handle Mowing position 5 mower. Mulcher plug CAUTION: Do not run your lawn mower without mulcher plug in place or approved clipping deflector or grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open. KNOWYOUR LAWN MOWER READTHISOWNER'S MANUALAND SAFETY RULES BEFOREOPERATINGYOUR LAWN MOWER. Compare the illustrations with your lawn mower to familiarize yourself with the location ...... of ratio,us controls and adjustments. Save this manual for future reference ..................... These symbols may appear on your lawn mower or in literature supplied with the product. Learn and understand their meaning, CAUTION OR WARNING ENGINE ON ENGrNE OFF FAST Engine zone control cabl_ SLOW CHOKE FUEL OIL DANGER, KEEP HANDS AND FEET AWAY Operator presence control bar _"--... Drive control lever knob G rass Engine oil cap with dipstick Ddve cover Mulcher Gasoline filler cap Engine speed control Lawn mower housing Primer Wheel adjuster (on each wheel) ........................................... MEETS CPSC SAFETY REQUIREMENTS Sears rotary walk-behind power lawn mowers conform to the safety standards of the American National Standards Institute and the U.S. Consumer Product Safety Commission. The blade turns when the enqine is runninq, Operator Presence Control Bar- must be held down to the handle to start the engine. Release to stop the engine, Primer- pumps additional fue! from the carburetor to the cylinder for use when starting a cold engine, Sarter Handle - used for starting the engine. Drive Control Lever-- used to engage power-propelled forward motion of lawn mower, Engine Speed Control - located on the side of the engine which allows you to select either fast or stow engine speed, Muicher Plug - located at the discharge opening must be removed when convert-, ing to bagging or discharging operation° 6 The operationofanylawnmowercan resultin foreignobjectsthrownintothe eyes,whichcan resultinsevereeyedamage.Alwayswear safetyglassesor eyeshieldswhileoperating yourlawnmoweror performinganyadjustmentsor repairs°Werecommenda wide visionsafetymaskoverthe spectaclesor standardsafetyglasses. HOW TO USE YOUR LAWN MOWER ENGINESPEEDCONTROL Theenginespeedis controlledby a lever locatedonthe sideofthe engine.Fast positionisfor startingthe engine,normal cutting,andbettergrassbagging,Slow positionis for lightcutting,trimmingandfuel economy. ENGINE ZONE CONTROL CAUTION: Federal regulations require an enginecontrol to be installedon this lawn mower in order to minimizethe risk of blade contact injury. Do not under any circumstances attempt to defeat the function of the operator control The blade turns when the engine is running° . Your lawn mower is equipped with an operator presence control bar which requires the operator to be positioned behind the lawn mower handle to start and operate the lawn mower. TO ATTACH GRASS CATCHER o Close the flip lid. Flip lid must be closed while operating lawn mower. ° Lift the rear door on the mower housing and ptace the grass catcher frame onto the formed tabs on the rear door hinge bracket. ° The grass catcher is secured to the lawn mower housing when the rear door is lowered onto the grass catcher frame. CAUTION: Do not run your lawn mower without clipping deflector or approved grass catcher in place. Never attempt to operate the lawn mower with the rear door removed or propped open. Hinge door bracket Grass catcher Formed tabs TO EMPTY GRASS CATCHER , To remove grass catcher, release operator presence control bar to stop engine. • Lift up rear door and remove the grass catcher by the handle. NOTE: Do not drag the bag when emptying; it wellcause unnecessary wear_ Primer TO ADJUST cU'rl'ING HEIGHT • Raise wheels for low cut and lower wheels for high cut. • Adjust cutting height to suit your requirements. Medium position is best for most lawns. ° To change cutting height, squeeze adjuster lever toward wheel. Move wheel up or down to suit your requirements. Be sure all wheels are in the same setting. NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, gposition adjusters (if so equipped) allow lever to be positioned between the plate tabs. LowerWheels for High Cut Raise Wheels b_'_ for Low Out _-_ P_ __ Lever DRIVE CONTROL ° Self-propelling is controlled by holding the operator presence control bar down to the handle and pushing the drive control lever forward until itclicks; then release the lever. • Forward motion will stop when the operator presence control bar is released, To stop forward motion without stopping engine, release the operator presence control bar slightly until the drive control disengages, Hold operator presence control bar down to handle to continue mowing without selfpropelling° ° To keep drive control engaged when turning corners, push down on handle and lift front wheels off ground while turning lawn mower. Operatorpresence controlbarX_\_ .._'_ _ Drive ,,\. /=, To engage drive control #ontrol disengaged BEFORE STARTING ENGINE OIL Your lawn mower is shipped without oil in the engine, o Be sure mower is level and area around oil fill is cleam ° Remove engine oil cap w/dipstick and fill to the full line on the dipstick. • Use 27 ozs. of oil. For type and grade of oil to use, see "ENGINE in Customer Responsibilities section of this manual. • Pour oil slowly. Do not overfill. • Check oil level before each use. Add oil if needed. Fit! to full line on dipstick. o To read proper level, tighten engine oil cap each time. • Reinstall engine oil cap and tighten. o Change the oil after every 25 hours of operation or each season. You may need to change the oil more often under dusty, dirt':/conditions. GAS o Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage° To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the fuel tank, start the engine and let it run until fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in fuel tank or permanent damage may occur. TO START ENGINE o To start a cold engine, push pdmer f'rce(5) times before trying to start. Use a firm push. This step is not usually necessary when starting an engine which has already run for a few minutes. • Push engine speed control lever to fast position. o Hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back. ° To stop engine, release operator presence control bar. NOTE: In cooler weather it may be necessary to repeat priming steps. In warmer weather over priming may cause flooding and engine will not starL If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. Engine oil cap Gasoline w/dipstick filler cap MOWING TIPS • Under certain conditions, such as very tall grass, it may be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of grass clippings. • For extremely heavy cutting, reduce the width of cut and raise the rear of the lawn mower housing one (1) wheel adjuster setting higher than the front for better discharge of grass. • For better grass bagging and most cutting conditions, the engine speed should be set in the fast position. ° When using a rear discharge lawn mower in moist, hea,,rygrass, clumps of cut grass may not enter the grass catcher. Reduce ground speed (pushing speed) and/or run the lawn mower over the area a second time. ° If a trail of grass clippings is left on the right side of a rear discharge lawn mower, mow in a clockwise direction with a small overlap to collect the clippings on the next pass. ° Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine airflow and extend engine life. , Poresinclothgrasscatcherscanbecome filledwithdirtanddustwithuseand catcherswillcollectlessgrass.To prevent this,regularlyhosecatchersoff yah water andlet drybeforeusing° MULCHINGMOWINGTIPS iMPORTANT." For best performance, keep mower housing free of built-up grass and trash. Clean UNDERSIDE OF MOWER HOUSING after each use. See "Cleaning" in CUSTOMER RESPONSIBILITIES section of this manual. o The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades° • Avoid cutting your lawn when it is wet° ',Net grass tends to form clumps and interferes with the mulching action° The best time to mow your lawn is the early afternoon, At this time the grass has dried and the newly cut area will not be exposed to the direct sun. 9 o For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one4hird of the grass blades. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut, mow slowly and raise the rear of the lawn mower one wheel adjuster setting higher than the front. o Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clipping& When doing a second cut, mow across or perpendicular to the first cut path. o Change your cutting pattern from week to week_ Mow north to south one weekthen change to east to west the next week. This will help prevent matting and graining of the lawn. MAX 1/3 .J M Checktor Loose Fasteners V' .... Clean/inspect Grass Catcher (If Equipped) Clear_ Lawn M0"_,_'er ................... '.......... _ ........... _ _ 6/ V _ _.._,f .......... L/_r clean (Power.PropeIred Under Drive Mowers) Cover ....... Check drive belt/pulleys RE (pp,we,pprope!ledMowers) C,hecldSh,a, rpenlRepiace Blade Lubrication Oha" _ 3 _:. .... :...........: ......... V ................. :_ : Cje_.n BatterylRechar! le ................ (Electric Start Mowers ................. E Check Engine Oil Level.......... N Change..Engine OII G Clean Air Filter I U V' ! ...lif4 I I I_ .............. I _'1,2 : : ......... I_ inspect MUffler ........................... Clean 0r Replace Spark Pl.u.g...... E Replace Air R]te_ Paper Cartridge I - Change more, oft4_'_w_n opera,rig L_ndor _ h_vy V'2 load or in high _mt_ont t_mp_r_ttur_ 2.,Sawl¢o moro orlonwhon oporatlng Indtty or dustycondiUor_ 3 ,, Roprac_bl_d_,s more oftgnwhan mowlng Inr_,andy r, oI[ LUBRICATION 4 .- Charge, 48 houm _t ond of soason GEN ERAL RECOMMENDATIONS CHART 1_) Wheel ad The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warrant,/, operator must maintain mower as instructed in this manual Some adjustments will need to be made periodically to properly maintain your unit. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. (_) Engine oil o Once ayear, replace the spark plug, replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assures proper air-fuel mixture and helps your engine run better and last longer, • Follow the maintenance schedule in this (_ Rear door hinge manual. BEFORE EACH USE - Check engine oil level. • Check for loose fasteners. LUBRICATION Keep unit welt lubricated (See "LUBRICATION CHART"). (_ Handle bracket mounting pin 1_ SPRAY LUBRICANT I'_ SAE 30 MOTOR OIL. REFER TO ENGINE- CUSTOMER RESPONSlBIUTIES SECTION. IMPORTANT: Do not oil or grease plastic wheel bearings. Viscous lubricants wil!attract dustand dirt that will shorten the life of the self lubricating bearings. Ifyou feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly. t0 PRODUCT SPECIFICATIONS MODEL NUMBER SERIAL 917.379300 NUMBER DATE OF PURCHASE HORSEPOWER: 6.6 DISPLACEMENT: 12.56 CU. IN. GASOLINE '1_5QUARTS CAPACITY/TYPE: UNLEADED OIL TYPE (API-SF/SGiSH): REGULAR SAE 30 (ABOVE 32°F) SAE 5W-30 (BELOW 32°F) OIL CAPACITY: SPARK PLUG(GAP: 27 OZ& .030") CHAMPION VALVECLEARANCE: RJ19LM INTAKE: .004 - .008 EXHAUST: .004 - ,008 SOLID STATE IGNITION AIR GAP: .0125 IN. BLADE 35-40 FT. LBS. BOLT TORQUE: The model and serial numbers will be found on a decal attached to the rear of the lawn mower housing_Record both serial number and date of purchase in space provided above. LAWN MOWER Always observe safety rules when performing any maintenance° TIRES • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. ° Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. BLADE CARE For best results, mower blade must be kept sharp. Replace bent or damaged blades. TO REMOVE BLADE ° Disconnect spark plug wire from spark plug and place "wirewhere it cannot come in contact with spark plug. • Turn lawn mower on its side, Make sure air filter and carburetor are up. • Use a wood block between blade and mower housing to prevent blade from turning when removing blade bolt. • Protect your hands with gloves and/or wrap blade with heavy cloth. ° Remove blade bolt by turning counterclockwise. Use a 9/16" box or open-end wrench. • Remove blade and attaching hardware (bolt, lock washer and hardened washer). NOTE: Remove the blade adapter and checkthe key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged_ TO REPLACE BLADE • Position the blade adapter on the engine crankshaft° Be sure key in adapter and keyway in crankshaft are aligned° o Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter. ° Be sure the trailing edge is up toward the engine. ° Install the blade bott with the lock washer and hardened washer into blade adapter and crankshaft. ° Use block of wood between blade and lawn mower housing and tighten the blade bolt, turning clockwise° ° The recommended tightening torque is 3540 ft. Ib& IMPORTANT: Blade bolt is grade 8 heat treated. 11 grass cuttings, etco are in the drive wheel area and must be cleaned to free drive wheels. If necessary to clean the drive wheels, check both front wheels. . Remove hubcaps, hairpin cotters and washers. o Remove wheels from wheel adjusters. o Remove any trash or grass cuttings from inside the dust cover, pinion and!or drive wheel gear teeth. ° Put wheels back in place. ° If after cleaning, the drive wheels do not turn freely, contact your nearest authorized service center. NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. TO SHARPEN BLADE Care should be taken to keep the blade balanced. An unbalanced blade wilt cause eventual damage to lawn mower or engine. o The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower. - To check blade balance, drive a nail into a beam or wall. Leave about one inch of the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in a horizontal position, tf either end of the blade moves downward, sharpen the heavy end until the blade is balanced. GEAR CASE o To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build--up. Clean under the drive cover twice a season_ ° The gear case is filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear GRASS CATCHER • The grass catcher may be hosed with water, but must be dry when used. ° Check your grass catcher often for damage or deterioration. Through normal use it will wear. If catcher needs replacing, replace only v,4tha manufacturer approved replacement catcher. Give the lawn mower model number when ordering. Blade Crank shaft adaptor Blade,., _.. _ Key_____ case. ° If lubricant is required, use only Texaco Starplex Premium 1 Grease, Part No. 750355. Do not substitute. ENGINE LUBRICATION k_ _,way _..., _ _ Use only high quality detergent oil rated with API service classification SF, SH or SG. Select the oil's SAE viscosity grade according to your expected operating temperature. SAE vlsc:osrP[ BLockwas/her H_ard;ned \" washer GRASS CATCHER "_Blade GRADES [ Cl_a_tk Trailing adaptor edge . The grass catcher may be hosed with water, but must be dry when used° ° Check your grass catcher often for damage or deterioration. Through normal use it will wear. If catcher needs replacing, replace only with a manufacturer approved replacement catcher. Give the lawn mower model number when ordering. DRIVE WHEELS Check front drive wheels each time before you mow to be sure they move freely_ The wheels not turning freely means trash, F_--' • :_0' I TEMPERATURE: o" ' ,_o" RANSE ANTICIPATED 60. B_FORE _{); i06; NEXT OIL CHANGE NOTE: Although multi_viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi_viscosity oils will result in increased oil consumption when used above 32°F_ Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 25 hours of operation or at least once a year if the lawn mower is not used for 25 hours in one year, 12 Checkthe crankcase oil levelbefore starting the engine and after each five (5) MUFFLER Inspect and replace corroded could create a hours of continuous use° Tighten oil plug securely each time you check the oil level, TO CHANGE ENGINE fire hazard and/or damage. SPARK PLUG OIL Change your spark plug each year to make your engine start easier and run better Set spark plug gap at .030 inch. NOTE: Before tipping lawn mower to drain oil, drain fuel tank by running engine until fuel tank is empty. CLEANING o Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with spark plug. o Remove engine oil cap; lay aside on a clean surface, • Tip lawn mower on its side and drain oil into a suitable container, Rock lawn mower back and forth to remove any oil trapped inside of engine. • Wipe off any spilled oil on lawn mower and on side of engine. o Fill engine with oil, Fil! only to the "FULL" line on the dipstick, DO NOT OVER FILL, - Replace engine oil cap, ° Reconnect spark plug wire to spark plug. IMPORTANT: For best performance, keep mower housing free of built--up grass and trash. Clean underside of mower housing after each use. CAUTION: Disconnect spark plug wire from spark plug and place ,Mre where it cannot come in contact with the spark plug. ° Turn lawn mower on its side. Make sure air filter and carburetor are up. Clean the underside of your lawn mower by scraping to remove build--up of grass and trash. o Clean engine often to keep trash from accumulating. A clogged engine runs hotter and shortens engine life. • Keep finished surfaces and wheels free of all gasoline, oil, etc. o We DO NOT recommend using a garden hose to clean lawn mower unless the Container electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can resutt in shortened engine life. AIR RLTER CLEAN UNDER DRIVE COVER Clean under drive cover at least twice a Your enginewill not run properly and may be damaged by using a dirty air filter. Replace the air filter even/year, more often ifyou mow in very dusty, dirty conditions. Do not wash air filter. season, Scrape underside of cover with putty knife or similar tool to remove any build--up of trash or grass on underside of drive cover, TO CHANGEAIR FILTER • Loosen cover screw. • Swing cover down and remove from hinge. o Pull paper filter out of air cleaner body, ° Clean air cleaner cover and body, ° Install a new paper filter, • Reinstall cover to air cleaner body, Be sure hinge is assembled properly. ° Swing cover up and tighten cover screw, (Do not overtighten). Air filter cover Hinge Paper filter muffler as it Cover knob 13 CAUTION: Before performing any service or adjustments: ° Release control bar. ° Make sure the blade and all moving parts have completely stoppe& • Disconnect spark plug wire from spark plug and place where it cannot come in contact with plug. o Remove the controls and operator presence control bar from the upper handle. • Remove hairpin cotters. ° Disconnect the lower handle from the handle brackets, o Turn the handle over and reassemble the hairpin cotters that have been removed. • Reassemble the controls and the operator presence control bar to the upper handle. CAUTION: The operator presence control bar must pivot freely to permit blade brake engagement when control bar is released. Do not over tighten the fasteners holding the controls to the upper handle° o To change from medium low to high position only the upper handle section will have to be turned over. o To change from medium low to low position, only the lower handle section will have to be turned over. LAWN MOWER TO ADJUST CUTTING HEIGHT See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual. REAR DEFLECTOR The rear deflector, attached between the rear wheels of your lawn mower, is provided to minimize the possibility that objects will be thrown out the rear of the lawn mower into the operator's mowing position. If the rear deflector becomes damaged, it should be replaced° TO REMOVE/REPLACE DRIVE BELT o Remove drive cover. Remove belt by pushing down on gear case pulley and rolling belt off it. ° Turn lawn mower on its side with carburetor and fuel cap up. o Remove blade. , Remove debris shield. o Remove belt from engine pulley on crankshaft° , Install new belt by reversing above steps. ° Always use factory approved belt to assure fit and long life. Medium Low Medium High Shipping Position Low Drive cover Belt High Push down TO ADJUST HANDLE "{our lawn mower handle can be raised or lowered for your mowing comfort. Four (4) positions are available: high, medium high, medium tow and low. Handles are shipped mounted in the medium low position. , To change from medium low to medium high position, the upper and lower handle sections will have to be turned over. = Remove the cable clips. Lower Handle Squeeze to remove Handle Bracket Hairpin Clip t4 ENGINE CARBURETOR Your carburetor has a non-adjustablefixed mainjet for mixturecontrol, If your engine does not operate properlydueto suspectedcarburetor problems,take your lawn mowerto an authorizedservice centerfor repair or adjustment. ENGINE SPEED Your engine speed has been factory set. Do not attempt to increase engine speed or it may result in personal injury. If you believe that the engine is running too fast or too slow, take your lawn mower to an authorized service center for repair and adjustment. Immediately prepare your lawn mower for storage at the end of the season or if the unit will not be used for 30 days or more_ Operator Presence Control Bar LAWN MOWER Upper Handle ,_//_"" _ When fawn mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area. o Clean entire lawn mower (See "CLEANING" in the Customer Responsibilities section of this manual). • Lubricate as shown in the Customer Responsibilities section of this manual. • Be sure that all nuts, bolts, screws, and pins are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary° • Touch up alt rusted or chipped paint surfaces; sand lightly before painting_ HANDLE You can fold your lawn mower handle for storage. • Squeeze the bottom ends of the lower handle toward each other until the lower handle clears the handle bracket, then move handle forward. ° Loosen upper handle mounting bolts enough to allow upper handle to be folded back. IMPORTANT: When folding the handle for storage or transportation, be sure to fold the handle as shown or you may damage the control cables° ° When setting up your handle from the storage position, the lower handle wilt automatically lock into the mowing position. Lower __'--..,. Handle Handte/_._.._ Bracket Squeeze t_,fol__... Cotter / , // ,,11 .'4_%Fold ) Fold Forward ForStorage Backward Mowing Position Lower Handle ENGINE FUEL SYSTEM IMPORTANT: It is important to prevent bum deposits from forming in essential juel system parts such as carburetor, fuel filter, fuel hose, or tank during storabe. Also, experience indicates that alcolol blinded fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage° Acidic gas can damage the fuel system of an engine while in storage. • Drain the fueltanK • Start the engine and let it run until the fuel lines and carburetor are empty. ° Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. o Use fresh fuel next season° NOTE: Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not drain the gas tank and carburetor if using fuel stabilizer. ENGINE OIL Drain oil (with engine warm) and replace with clean engine oil. (See "ENGINE" in the Customer Responsibilities section of this manual). 15 CYLINDER o Removesparkplug. = Pouroneounce(29ml) ofoilthroughspark plugholeintocylinder. ° Pull starter handle slowly a few times to distribute oil • Replace with new spark plug. OTHER = Do not store gasoline from one season to another. ° Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. ° If possible, store your unit indoors and cover it to give protection from dust and dirt. TROUBLESHOOTING ,,,,,,,_ _,,,, = Cover your unit with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your unit to rust IMPORTANT: Never cover mower while engine and exhaust areas are still warm. CAUTION: Never store the lawn mower with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure. CHART ,, PROBLEM Does not start CAUSE CORRECTION • Dirty air filter. = Out of fuel. ° Stale fuel. Clean/replace air filter. ° Fill fuel tank. ° Drain tank and refill with fresh clean fuel. , Drain fuel tank and carburetor and refill tank with fresh gasoline. ° Connect wire to plug. ° Water in fuel. • Spark plug wire is disconnected. • Bad spark plug. • Loose blade or broken blade adapter. • Control bar in released position. • Control bar defective, Loss of power • Rear of lawn mower housing or cutting blade dragging in heavy grass° ° Cutting too much grass. o Dirt/air filter. , Buildup of grass, leaves, and trash under mower. • Too much oil in engine. • Walking speed too fast. 16 o Replace spark plug. ° Tighten blade bolt or replace blade adapter, • Depress control bar to handle. o Replace control bar. ° Set to '"Higher Cut" position. ° Set to "Higher Cut" position. ° Clean/replace air filter. ° Clean underside of mower housing. Check oil level. • ° Cut at slower walking speed. TROUBLESHOOTING PROBLEM 'P'oor cut- CHART 3AUSE tineven 'worn, CORRECTION bent or loose bladel o Wheel heights uneven, -" ;Replace blade, Tighten blade bolt, , Set all wheels at same height ° Set engine speed control o Low engine speed, • Buildup of grass, leaves and trash under mower° in fast position° o Clean underside of mower housing. LJJJ Excessive _° Worn, bent or loose blade. vibration = Bent engine crankshaft. , Replace blade° Tighten blade bolt. • Contact an authorized service center, ,,, Starter rope hard to pull lilt,, ° Engine flywheel brake is on when control bar is released, , Depress control bar to upper handle before = Bent engine crankshafL pulling starter rope° , Contact an authorized service center, o Blade adapterbrokeno ° Blade dragging in grass. • Replace blade adapter. • Move lawn mower to cut grass or to hard surface to start engine. • Raise cutting height. not filling (if so ° Cutting height too low. o Lift on blade worn off° equipped) • Catcher not venting air. ° Clean grass catcher. ° Low engine speed.. • Set engine speed control in fast position. , Grass is too high or wheel height is too low. ° Rear of lawn mower housing or blade dragging in grass. • Grass catchertoo full. • Handle height position not fight foryou_ • Raise cutting height, Grass catcher iHard to push 17 ° Replace blade. • Raise rear of lawn mower housing one (!) setting higher. • Empty grass catcher. • Adjust handle height to suit_ CRAFTSMAN Garantt'a Reglas de Seguridad Montaje OperaciSn Mantenimiento Programa de Mantenimiento Model No. 917.379300 17 t7 19 20 24 24 Especificaciones del Producto Ser¢icio y Adjustes Almacenamiento Identificaci6n de problemas Partes de repuesto Orden de Partes 25 27 28 30 Vea el manual ing[Eisdel dueSo Contratapa GARANT[A LIMITADA DE DOS A_OS PARA LA SEGADORAA MOTOR CRAFTSMAN Por dos (2) aSos, a partirde la fecha de compra, cl_ando esta Segadora Craftsman se mantenga, lubrique y afine segSn las instruccionespara la operad6n y el mantenimiento en et manual del dueSo, Sears reparar_ gratis todo defecto en el material y la mano de obr& Si la Segadora Craftsman se usa pare fines comerciales o de arfiendo, esta garant[a s61ose aplica por noventa (90) dies a pa_r de la fecha de compra. Esta Garantfa no cubre: • Artfculos que se desgastan durante el uso normal tales como las cuchillas segadoras rotatorias, los adaptadores de la cuohilla, tas coffees, los fittros de alre y las bujfas. • Reparaciones necesarias debido a] abuso o ala negligencia del operador, incluy_ndosea los cigLieSales doblados y ata falta de mantenimiento del equipo segdn las instrucciones que se incluyen en el manual del duefio. EL SERVlCIO DE GARANT[A ESTA DISPONIBLE al devolver la segadpra a motor Craftsman al centro/ departmento de servicio Sears mas cercano en los estados unidos. Esta garantfa se aplica solamente mientras el producto este en uso en los estados unidos_ Esta Garanti'a le otorga derechos legales especificos, y puede que tarnbi_n tenga otros de rechos que vaffan de estade a estado. Sears, Roebuckand Co., DI817WA, Hoffrnan Estates, IL 60179 USA Los estandrares de seguridad exJgen la presencia del operator en los controtes pare reducir a un minimo el riesgo de lesionarse. S u unidad viene equipade con dichos controles. Por ningun motivo trate del eliminar la funci6n de los controles que exigen la presencia del operador. ENTRENAMIENTO: - Lea este manual de! operador cuidadosarnente.Familiaffcesecon los controles y aprenda a operar su segadora an forma ade_Jada. Aprenda a parer su segadora r'_pidemente. • No parmita que los niRos usen su segadora. Nunca permita que los adultos operen la segadora sin contar con las instrucciones adecuadas. , Mantenga el _rea do operaoiSn despejada de gente, especialmente de niRos pequefios y de animales dom_sljcos. ° Use la segadora sotamente pare los fines propuestos por el fabric=antey segQn tas explicaciones descritas en esta manual, • No opere la segadora si so ha cai'do o daSado en cualquiera form& Siempre repare los deSos antes de usarl& ° No use accesorios que no hayan sido recomendados por el fabricante. El uso de dichos accesorios puede ser peligrosoo • La cuchiUagira cuando el motor est_ funcionando, PREPARACiON: • Siempre revise cuidadosamente el _rea que se va a segar y desp_jela de todas las piedras, palos, alambres, huesos y otros objetos extraSos. Estos objetos ser'_ lanzados con la cuchilla y pueden producir lesbnes graves. • Siempre use anteojos de seguridad o protectores do ojos cuando arranque y durante el tJempoque use la segador& • V[stase en forma adecuada. No opere la segadora sin zapatos o con sandalias abiertasoUse solamente zapatos s61idoscon buena tracd6n cuando siegue. • Revise el estanque de combustible antes de haoer arrancar e! motor. No Ilene el estanque de gasolina en recintos cerrados, ni cuando el motor est#, funcionando o cuando est& catiente. Permita que et motor se enfn'e por varios minutos antes de tfenar el estanque de gasoline. Umpie toda la gasoline derramada antes de hacer arrancar el motor. ° Siempre haga los ajustes de altura de las ruedas antes de hacer arrancar su segadora. Nunca trate de hacer _sto mientras que el motor est_ funcionando. • Siegue siempre durante el dfa o con buena luz artificial. OPERAClON: Mantenga sus ojos y su mente en la segadora yen el _rea que se est_ cortando No permita que otros intereses io distraigano ° No corte c_sped mojado o resbaloso. Nunca corra mientras est_ operando su segadora. Siempre aseg_rese de mantener el equilibrio - mantenga el mango agarrado firrnemente y camineo ° No ponga las manos o los pies cerca odebajo de las partes rotatoriaso Mant_ngase alejado de la abertura de descarga en todo momento. • Siempre pare el motor cuando se vaya ocuando no est_ usando su segadora, o antes de atravesar las entradas pare autos, los senderos, caminos y _,reas cubiertas de ripio, ° Nunca dirija la descarga del material hacia los espectadores ni perrnita a nadie cerca de la segadora mientras la est_ operando. • Antes de timpiar, inspeccionar o de reparar I a segadora, pare el motor y est_ completamente seguro de que la cuchilfa y que todas las partes que se mueven se hayan detenido Luego, desconecte el alambre de la bujfa y mant#ngalo alejado de _sta pare evitar el arranque por accidente. • No contJnde haciendo funcionar su segadora si le pega a un objeto extra rio. Siga et procedimiento descrito anteriormente, luego repare cuaiquier daSo antes de volver a arrancar y de operar su segadorao ° No cambie los ajustes del regulador o hagaque el motor ande a una velocidad excesiv& Se pueden producir daRos en el motory t esiones personales • No opere su segadora si vibra fuera de lo normal. La vibraci6n excesiva es una indicaci6n de da5o; pare el motor, revise en fonTla segura la causa de la vib raci6n y haga las reparaciones segLin sea necesario. • No haga funcionar el motor en recintoscerrados. Los gases de escape son peligrosos. ° Nunca corte el c_sped tirando la segadora hacia usted. $iegue a trav_s de la care de las pendientes, nunca hacia arriba o hacia abajo pues puede perder el equilibrio No siegue pendientes demasiado empinadas. Tenga cuidado cuando opere la segadora en terreno disparejo o cuando cambie de direcci6n - mantenga un buen equilibrio • Nunca opere la segadora sin las protecciones adecuadas, las planchas, el recogedor de c6sped y otros disposffivos de seguridad en su lugar. MANTENIMIENTO TO." , , • • ° • • ° • Y ALMACENAMIEN- Revise la cuchilla y los pemos de montaje del motor a menudo, pare asegurarse que est_n apretados an la forma adecuada. Revise todos los pemos, tuercas y tomillos a intervalos frecuentes, pare verificar si est_n apretados en forma adecuada, y asegurarseque la segadora se encuentra en condiciones de funcionamiento seguro. Mantenga todos los dispositivos de seguridad en su lugar y listos pare funcionar Pare reducir el peligro de incendio, mantenga el motor sin c6sped, hojas y grasa o aceite en exceso. Revise el recogedor de c_sped a menudo pare verificar si hay deterioro y desgaste y cambie las bolsas desgastadas. Use solamente las bolsas de repuesto recomendadas por el fabricante de su segadora o que cumplen con las especificaciones de _ste. Siempre mantenga una cuchilla afilada en su segadora. Siempre permita que el motor se enfffe antes de guardarla en cualquier recinto cerrado. Nunca guarde la segadora con combustible en el estanque dentro de un edificio endonde los gases pueden alcanzar una llama expuesta o una fuente de ignici6n, tel como el calentador de ague, la estufa de calefacci6n, la secadora de rope, etc. PRECAUClON: Siempre desconecte el alambre de ia bujia y p6ngalo donde no pueda entrar an contacto con la buj[a, pare evitar el arranque por accidente, durante la preparaci6n, el transporte, el ajuste o cuando se hacen reparaciones. PRECAUClON: Es conocido por el Estado de Catifomia que los gases de escape del motor de este productor contienen quimicos los cuales a ciertos niveles, pueden ocasionar, c&ncer, defectos de nacimiento, y otros daGos al sistema reproductivo, 19 Estos accesorios estaban disponibles cuando se produjo la segadorao Tambi_n est_TLn disponibles an la mayorfa de las tiendas de Sears y en los centros de servicio_ La mayori'a :{ENDIMIENTO de las tiendas Sears tambi_n pueden mender a pedir partes de repuesto pare usted, si les proporciona el ndmero del modelo de su segadorao Algunos de estos acoesorios tel vez no se apliquen a su segadora. DE LA SEGADORA J DESVIADOR DE RECORTES PARA SEGADORAS CON DESCARGA TRASERA JUEGOS PARA LA ACOLCHADORA RECOREDOR PAPA SEGADORAS CON DESCARGA TRASERA l ESTABILIZADORES PARA SEGADORAS CON DESGARGA RECOREDOR LATERAL ENVASES DE GASOLINA Jt, ,i ,i VIANTEN1MIENTO DE LA SEGADORA CUCHILLAS BUJ[AS FILTROS DE AIRE SILENCIADORES ADAPTADORES DECUCHILLA Lea estas instruccionesy este manual completamente antesde tratarde montaru operar su segadora nuevaoSu segadora nueva ha sido montada en la f_brica con la excepci6n de aquellas partes qua se dejaron sin montar por razones de envi'o.Todas las partes como las tuercas, tas arandelas,los pemos, etc°, que son necesarias pare completer el montaje hen sick)colocadas en la bolsa de partes. Pare asegurarse que su segadora funcione en forrna segura y adecuada, todes las partes y los artfculos de ferreten'a que se monten tienen que serapretades seguramente. Use las herramientas correctas, como sea necesario, pare asegurar qua so aprieten adecuadarnante. PARA REMOVER LA SEGADORA DE LA CAJA DE CARTON • Remueva las partes sueltas que se incluyencon la segadom° • Corte las dos esquinas de los extremos de la caja de cart6n y tiendael panel del extremo piano. • Remueva todo el material de empaque, excepto ia curia entre et mango supefiory _i inferior, y la curia que sujeta la barra de los control que exige RUEDAS ACEITE DEL MOTOR la presencia del operadorjunto con el mango superior, Haga rodar la segadora hacia afuera de la caja do cart6n y revfsela cuidadosamante pare verificar si todavt'aqued.an partes sueltas adicionales. COMO PREPARAR SU SEGADORA PAPA DESDOBLAR EL MANGO IMPORTANTE: Despliegue el mango con mucho cuidadopare no pe[lizcar o dafter los cables de control • Levante los mangos haste que la secc_6ndel mango inferiorse asegure an su lugar,en la posici6n pare segar. • Remueva la curia protectora, levante la secci6n del mango superior haste su lugar on eI mango inferior y apriete ambas manillas del mango. • Remueva ta cuSa del mango que sujeta la barra de los control que exJge fa presencia del operadorjunto con el mango superior. • El mango de la segadera puede ajustarse segL_n le acomode pare segar. Refi_rase a "AJUSTE DEL MANGO" en la Secci6n de Servicio y Ajustes de este manual. 2O Barra de control que exige ta presencia del operador Mango Levantar Levantar Mango inferior PosiciSn pare segar PARA INSTALAR LOS ACCESORIOS o Ahora puede instalar e! recogedor o el desviador de recortes opciona]o • Pare vofver ala operaci6n de acolchamiento con capa vegetal, instale la tapon acolchadora en la abertura de descarga de la segadora. PRECAUClON: No haga funcionar su segadora sin la tapon acolchadora aprobada en su lugar, o sin el desviador de recortes, o sin el recogedor de c_sped, aprobados, en su tugar. Nunca trate de operar la segadora cuando se ha removido la puerta trasera o cuando es_ un poco abler,a, Su segadora rue enviada lista pare usarse como una acolchadora de cape vegetal, Pare convertida de modo que pueda ensacar o descargar. • Abra la puerta trasera y remueva la tapon acolchadora. Gu&'deta en un lugar seguro. Tapon alcolchadora FAMILIARICESE CON SU SEGADORA LEA ESTE MANUAL DEL DUEIqO Y LAS REGLAS DE SEGURIDAD ANTES DE OPERAR SU SEGADORA Compare las ilustraciones con su segadora pare familiarizarse con la ubicaci6n de los diversos controles y ajustes. Guarde este manual para referencia en el futu roo Estos simbolos pueden apareser sobre su segadora o en la literature proporcionada producto. Aprend_om_da_ AI"_ _3"_C_ _N O ADV_R'TB,_CIA ii rEII_rFF " significados. MO'_OR _I_E'_D'DO ........... Con el MCTOR R/_PfDO APAGADO_ .......................... I.F..P_O F_'[P,AH 0JJ CCM* LAGt_ H ,,,, BUaTIB,L_ ACStTE PJ_.,It_R D (3UARDE L _,,S MA_gD_ YLO_ PIES LEJO_; ,................ Cable de control de la Barra de control que exige la presencia del ...... velocidad del motor Control de impulsi6n Cord6n arrancador Manilla del mango Recogedordet c_sped Tape del relleno de la gasoline Tape del deposito de aceite del motor con varilla indicadora de nivel Tapon de la acolch Cubierta de la impulsidn Control de la velocidad del motor Ajustador de la rueda (en cada rueda) Cebador Oaja CUMPI F CON LOS REQUISITOS DE SEGURIDAD DE LA CPSC Las segadoras a motor, que se conducen desde la parte de atr_s, rotatorias, Sears, cumplen con los est_ndares de seguridad delAmerican National Standards Institute y de la U.S. Consumer Product Safety Commission, La Cuchilla gira cuando el motor est_ fiJncionando. Barra de control que exige la presencia del ......... Palar_cade controi d_ ia impulsian -"_e usa pare enganchar la segadora para movimiento operador-- _ene qua sujetarse abajo, junto con el hacia adelante impulsada a motor, mango, pare hacer arrancar el motor. Su6ttela pare parer el motor. Palanca de control de la velocidad dei motorm Cebadorw bombea combustible adicional desde e! situada en la parte lateraJdel motor que le permite seleccionar la velocidad del motor ya sea r_pida o ca[burador al cilindro para uso cuando se necesita lent& hacer arrancar un motor fifo. CordSn arrancador--se el motor. usa para hacer arrancar Tapon de la acolchadora-- permite la conversi6n 21Para la operaci6n de descarga o ensacado° PARA MONTAR Y ADJUNTAR EL RECOGEDOR DE ClaSPED Laop_racjSn decuatquiersegadora puede hacerquesaltenobjetos extrafosdentrodesus ojos,Ioquapuedeproducir dafosgraves en _stoso • Cierre ta tape soltable. La tape soltable debe ester cerrada cuando se esta operando la segadora. • Levante la puerta trasera de la caja de la, segado ray ponga el bastidor del recogedor de c_.sped en las orejas formadas en el puntal de bisagra de la puerta trasera. o El recogedor de r_sped esta asegurado en la caja de la segadora cuando se baja la puerta trasera pare descansar en el baslJdordel Siempre use anteojos de segulidad o protecci6n pare los ojos mientras opera su segaciora o cuando haga ajustes o reparaciones° Recomendarnos una mascara de seguridad de visi6n amptia, pare uso espejuelos o anteojos de segurided estandarte. COMOUSARSUSEGADORA CONTROL DE LA VELOClDAD DEL MOTOR La velocidad det motor se controla por medio de una paJancaubicada en el lade del motor. La posici6n de rApide se usa para arrancarel motor, pare el corte normal y un major ensacamiento del c_sped. La posici6n lento as pars torte IMano, recorte y pare economizar combuslJble° CONTROL DE ZONA DEL MOTOR Palanca de control de la velocidad det motor recogeder _ c_sped PRECNJCl6N. No haga funcionarsu segadora sin el desviador de recortes o sin el recogedor de c_sped, aprobados, en su [ugar. Nunca trate de operar la segadora cuando se ha removido la puerta ,traserao cuando est_ un poco abierta. trasera Puntal de bi_ Bastidorde recogedordel cesped Cebador_ Orejas _ formadas PARA VACIAR EL RECOGEDOR PRECAUCl6N: Las regulaciones federales exigen que se instale un control para et motor en esta segadora pare reducir a un mt'nimo el riesgo de lesionarse debido al contacto con la cuchilla, Por ningdn motivo trate de eliminar la funci6n del contmt del operador. La cuchitla gira cuando el motor est_ funcionande. • Su segadora viene equipada con una barra de control qua exige la presencia del operador, 1o qua requiere qua el operader est_ detr_s del mango de la segadora pare hacel_aarrancar y operada. DE ClaSPED ° Pare remover el recogedor del c_sped suelte fa balTa de control del operador para poder parer el motor. • Levante la puerta de atras y remove el recogedor del c_sped por el mango, AVlSO: No arrastre la boise cuando la vacfe; se producir& un desgaste innecesario, PARA AJUSTAR LA ALTURA DE CORTE - Levante las ruedas pare el corte bajo y baje tas nJades pare el corte aJtoo • Ajuste la altura de corte pare qua se acomode a sus requisitos. La posici6n de! medio es la major pare la mayorfa de los c_spedeso • Pare carnbiar is altura de corte, empuje la pa]anca del ajustador ha_a la rued& Mueva la rueda hacia arriba o hacia abajo de mode que se acomode a sus requisitos. AsegOrese qua todas las medas queden igualmente ajustadas, ATENCl6N; El ajustador esta correctamente colocado cuando las orejas de la place est&n insertadas en e! agujero del mango. Tambi_n, los a_ustesde 9 posiciones (si equlpado} permiten qua el mango pueda ser movido entre las orejas de la Pare un corte alto, baje las ruedas CONTROL ° La autoimpulsi6n se controla el sujetar la barra de control qua exige le presencia del operador hacia abajo en el mango y al empujer la palanca de control de la impulsion hacia adelante haste qua suene "clio," luego se suelta la palanca. ° EI movimiento hacia adelante parar_ cuando la barra de control que exige le presencia del operador se suelta. Pare parer el movimiento hacia adelante sin parar el motor, suelte la barra de control que exige ]a presencia del operador un poco haste qua se desenganche el control de la impulsi6n., Sujete la barra de control qua exige la presencia del operador abajo en contra del mango pare continuer segando sin autoimpulsi6n. Orejas de laplaca Mango Pare un corte bajo, levante las ruedas DE LA IMPULSION 22 o Pare mantener el control de la impulsi6n enganchado cuando se de vuelta en las esquinas, empuje el mango hacia abajo y levante tas ruedas delanteras fuere del suelo al girar la segadora. Barre de control qua exige la presencia del operador \,\ . \ Control de arrancar et motor y h&galo funcionar haste qua las Ifneas del combustible y el carburador queden vac_'os.La pr6xima tamporada use combustible nuevooVealas Instrucdones Para El #Jmacenamlento pare m&s informaci6n, Nunca use productos de limpieza pare e! motor o para el carburador en el estanque de! combustible pues se pueden producir daSos permanentes, PARA HACER ARRANCAR EL MOTOR Pare enganchar el control de la impulsi6n Control de ta impulsi6n desenganchado ANTES DE HACER ARRANOAR EL MOTOR ACEFrE Su segadore rue enviada sin aceite en el motor. • AsegL1resequa la segadora est_ nivetada y qua el _,rea alrededor del dep6sito de aceite est_ limpia. • Remueva }a tape de{ dep6sito de aceite del motor con la varilla indicadora de nivel y rellene has_ }aIfnea de llano en 6sta. o Use 0,61 {27 oz_) de aceite,, Pare el lJpoy la caHdad vea'MOTOR" en la secoiSn de las "Responsabilidades del Client#' en este manual. o Vac[e el aceite lentamente. No lo ftene demasiado. - Revise el nivel del aceite antes de cada uso. Agregue aceite si es neoesario. Liana haste la Ifnea de !leno en la varilla indicadora de nivel. ° Pare leer el nivel adecuado, apfiete la tape def dep6sito de aceite del motor cada vez: • Vuetva a instalar la tapa del dep6sito del aceite y apfi6tela. ° Cambie el aceite despu_s de 25 horas de operaci6n o una vez por temporada. Puede necesitar cambiar el aceite m_s a menude cuande las condidones son po_#orosaso sucias. ° Pare hacer arrancar un motor fn'o, empuje el cebador cinco (5) veces antes de tratarlo. Use un empuja _nnemante, Este paso normaJmente no es necesado cuando se hace arm_ncarun motor qua ya ha estado funcionando por unos cuantos minutos_ ° Mueva la palanca de control de velocidad a la posici6n de r_pido, • Sujete la barra de control qua exige la presencia del operador abajo an et mango y tire el mango del arrancador rgpidamente_ No pmTnita que el cord6n del arrancador se dewaelva abruptamente. • Pare parer el motor, suelte [a barra de control qua axige la presencia del operedor. AVISO: En dimas rags fn'os puede qua sea necesario repetir los pesos del cebado. En ctimas mg.s ca]urosos el cebar demasiado puede producir el ahogo y el motor no va a arrancar. Si se ahoga el motor espere unos cuantos minutos antes de tratar de hacedo arrancar y no repita los pasos det cebad& Tapa det deposito de {a gasoline Tapa del deposito de aceite del motor con varilla indicadora de nivel GASOUNA • Uene e} estanque de combustible,. Use gasoline regular, sin plomo, nueva y limpia con el minimo de 87 octanos. No mezcle el aceite con la gasoline, Pare asegurar qua la gasolina utJlizada sea fresca compre estanques los cuaJes puedan ser ut_lizados durante los primeros 30 dlras. ADVERTENCIA: La expefiencia ha indicado que los combustibles mezclades con alcohol (conocidos como gasohol, o el uso de etanol o metanol) pueden atraer la humedad, la qua conduce ala separaci6n y formaci6n de _cidos durante el a]macenamiento. La gasoline acidica puede darer el sistema del combustible de un motor durante el almacenamiento. Pare evitar los problemas con el motor, se debe vaciar el sistema del combustible antes de guardarlo por un peffode de 30 di'as o m_s. Vacie el estanque del combustible, haga 23 CONSEJOS PARA SEGAR . Bajo ciertas condbiones, tal como c4sped muy alto, puede ser necesario el elevar la altura del corte para reducir el esfuerzo necesario para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c6sped. • Para un corte muy pesado, reduzca el ancho del corte pasando parcialmente por encima del lugar anteriormente cortado y siegue lentamente. • Pare un mejor ensacado del c6sped y para la mayorfa de las condiciones de corte, Ia velocidad del motor debe ajustarse a la posiciSn de r4,=pido, o Cuando use una segadora con descarga trasera en c4sped h_medo y pesado, los montones del c_sped cortado puede que no entrenen e! recogedor de c_sped. Reduzca la ve!ocidad del recorfido (velocidad de empuje) y/o haga funcionar la segadora sobre el #,rea por segunda vez. ° Si queda una huefta de cortes en el lado derecho de una segadora con descarga trasera, siegue en la direcd6n en que giran las mani!las del reloj, solapando un poco para recaudarlos recortes en la prSxima pasad& ° Los poros en los recogedores de c_sped de tela pueden llenarse con mugre y polvo con el uso y los recogedores recaudar_n menos c4sped. Para evitar 6sto, rocfe el recogedor con la manguera de agua regularmente y d4jelo secarse antes de usarlo. • Mantenga la parte superiordet motor, atrededor del arrancador, despejada y sin recortes de c6sped y paja Esto ayudar_ el ftujo deI aire del motor y extender_ la durad6n @ste. Max, 1/3 CONSEJOS PARA SEGAR Y _j, ACOLCHAR IMPORTANTE: Pare obtener el mejor rendimiento mantenga fa caja de la segadora sin acumulacion de cesped y basurao Vea "limpieza" en la seccion de "RESPONSABILIDADES DEL CLIENTE" de este manual ,, La cuchilla acolchadore especial va a volver a cotter los recortes de c4sped muchas veces, y los reduce en tamaSo, de modo que si se caen en el c4sped se van a dispesar entre 4ste y no se van a notar. Tambi4n, el c_sped acolchado se va a deshacer r_pidamente entregando substancias nutritivas para el c_sped, Siempre acolche con la velocidad del motor (cuchilla) m_s alta, pues asf se obtendr& la mejor acci6n de recorte de las cuchillas, o Evite cortar el c6sped cuando est6 mojado, E1 c4sped mojado tiende a forrnar montones e interfiere con la acciSn de aco]chado,, La mejor hora para segar el c_sped es temprano en la tarde. A esa bore 6ste se ha secado y el _rea reci#n cortada no quedar_, expuesta al sol directo, . Para obtener los mejores resultados, ajuste la altura de! corte de la segadora de modo que 6sta corte solamente el tercio superior de las hojas de c4sped, En el caso de que et c6sped haya crecido demasiado, puede ser necesario el elevar la aftura det corte para reducir el esfuerzo necesafio para empujar la segadora y para evitar sobrecargar el motor, dejando montones de recortes de c6sped. Para tin acolchamiento muy pesado, reduzca el ancho del corte pasando por encima del lugar anteriormente cortado y siegue lentamente.. ° Ciertos tipos de c6sped y sus condiciones pueden exigir que tin ,_rea tenga que ser acolchada por segunda vez pare esconder completamente los recortes, Cuando se haga el segundo corte, siegue atravesado o en forma perpendicular a la pasada del primer corte. ° Cambie su patr6n de corte de semana a semana. Siegue de norte a sur una semana y luego cambie de este a oeste la pr6xima semana. Esto evitar_ que el c6sped se enrede y cambie de direcci6n. 24 -1- PROGRAMADE MANTENIMIENTO Lirr, piar/inspgccionar elrscogadotde S o_-spau (slv,_nsoqulp_do) E .Llrnptar la,s,egadora _' j .. v' , AG Llmpfsr debajo de Iscon cublerla Is trans* mist6n (s_gadoras poder de propulsor) ,d,.as(segad,o,r_s poder PrOPU!Ssr) DO sa Rovisar tas coffees con y las poleas tmpuF ' Rsv_ar olafliar/oamblar la Ouchllla " ....... If Of' 3 " Ltmpiar {a bstsrf_recargar (ssgsaoras con arranque el_ctrioo) V_41 If ,,,;,,;, ! Camblar el acelte del rnolor LImp_ar _ _'iiiro do_ro ! I ........ , i V'2 _........ ,,, . :.. _ ! .... ! ....... ,, ..... ,, ! , ..... I TO Inspeoci0nar ei Siienclador .................... v" Cambtar == de airs 1 - O_mbi_r el cartucho da papal rn_; a menudo ¢uando delftltrs se opera boio calg_ pe_ad_ o en _mbientes con _lla_, lemper_luras Z ,. Dar servicio m&s a menudo cu_ndo so opera en condiclone_; _UC{aso poivoros*_*_, 3 - Cambie la.a ¢uchil{_s m_,s a monudo cuando ._iegue an terreno arenoso 4 - Cargar por48 hor_s r,1finds ta temporad_ TABLA RECOMENDAClONES DE LUBRlCACl6N GENERALES l_)Aceite La garanti'a de esta segadora no cubre los arti'culos que hen estado sujetos ai abuso o ala negligencia del operador. Pars recibir todo el valor de ia garant(a, el operador tiene que mantener la segadora segL_nlas instrucciones descritas en este manual de motor (_ Ajustador de la rueda Hay algunos ajustes que se t_enenque hacer en forms peri6dica psra poder mantener su unidad adecuadarnente. Todos los ajustes en la secci6n de Servicio y Ajustes de este manual tienen que ser revisados por io menos un vez por cads temporada. • Una vez ai a5o, cambie la buj_'a,limpie o ce_nbie el elemento del filtro de aim y revise sita cuchilla est_ desgastada. Una bujfa nueva y un elemento del filtro de sire limpio/nuevo aseguran la mezcla de aim-combustible adecuada y awdan a que su motor funcione mejory que dure m_.s. • Siga el programs de mentenimiento en este manual ANTES DE CADA USO • Revise el nivel de! aceite del motor, • Revise si hay sujetadores sueltos. LUBRtCAC!ON Mantenga la unidad (_ a de montaje del puntal del mango © ® Bisagra de la puerta trasera Rocie el lubricante Aciete de motor de SAE 30. refierase ala seccion de responsibifidades del cliente en 'MOTOR" IMPORTANTE: No aceite o engrase los rodamientos de la rueda de plastico. Los lubricantes viscosos atraemn pofvo y mugre, Io que acortara la duraci6n de los rodamientos autolubficantes. Si cree qua tienen que lubricarse, use solamente un lubricante tipo grafito, de polvo seco in forms moderada. bien lubricada 25 ESPECiFiCACIONES NOMERO DE MODELO _0MERO J DEL PRODUCTO 'i 917.379300 DE SERIE FECHA DE COMPRA CABALLOS 6,6 DE FUERZA: DESPLAZAMIENTO: t2.5601J. IN. CAPACIDAD Y TIPO DE GASOLINA: 1.5 Cuartos REGULAR SIN PLOMO TtPO DE ACEITE: (API-SF/SG/SH) SAE 30 (sobre 32°F) SAE 5W-3o (debajo 32°F) CAPACtDAD 27 oz. de capacidad DE ACEITE: BUJ[A (ABERTURA: TOLERANCIA SENCENDIDO CHAMPION .030") DE VALVULA: RJ19LM ADMISl6N: .004 - .008 DESCARGA: ,004 - .008 DE ESTADO SOLIDO ABERTURA DE AIRE: .0125 IN, TORSION DEL PERNO DE LA CUCHILLA: 35-40 FT. LBS, o El num6ro del nodelo y el de serie se encuentran en la calcomania adjunta a la parte trasera de la caja de la segadora. Debe registrar tanto et num6ro de serie come la fecha de compra y mantengalos en un lugar seguro para refencia en el futuro. SEGADORA Siempre observe las reglas de seguridad cuando haga el mantenimiento. LLANTAS o Mantenga las Ilantas sin gasolina, aceite o substancias quimicas para control de insectos que pueden da5ar la goma. • Evite fos tocones, las piedras, las grietas profundas, los objetos afilados y otros peligros que pueden daSar alas Ilantas. • Remueva el pemo de la cuchilla gir_ndolo en el sentido contrario en que giran las manillas del retoj, • Rernueva la cuchilla y los artfculos de ferreterfa adjuntadores (el pemo, la arandela de seguridad y la arandeta endurecida), AVISO: Remueva el adaptador de la cuchilla y revise el cubo interior de la ranura del adaptador de la cuchilla, La ranura tiene que estar en buenas condiciones para que funcione en forrna adecuada. Cambie el adaptador si est,. da5ado, CUIDADO DE LA CUCHILLA PARA CAMBIAR Para obtener los mejores resultados, la cuchilla de ta segadora tiene que mantenerse afilada. Cambie la cuchitla doblada o daSada, PARA REMOVER L,A CUCHILLA ° Ponga el adaptador de la cuchi!la en el cigue5al del motor. Asegdrese que la ranura del adaptador y que el chavetero del cigue_al est_n alineados. • Ponga la cuchilla en el adaptador de _sta alineando los dos (2) agujeros en la cuchilla con las salientes elevadas en el adaptador, ° Asegdrese de que el borde de salida de la cuchilla (opuesto al horde afilado) est_ hacia arriba hacia et motor. • Instale el pemo de la cuchilla con la arandela de seguridad y ta arandela endurecida en el adaptador de la cuchilla y el cigue5al° LA CUCHILLA • Desconecte el alambre de la bujfa y pSngalo en donde no pueda entrar en contacto con _sta. ° Haga descansar la segadora en su lado. Asegcirese que el filtro de aire y que el carburador queden mirando hacia arriba, • Use un bloque de madera entre la cuchilla y la caja de la segadora para evitar que la cuchilla gire cuando se le quite el pemo. • Proteja sus manos con guantes y/o envuelva la cuchilta con una tela gruesa. 26 -t RUEDAS DE IMPULSION • Useunbloquedemaderaentrela cuchillay la cajadela segadora y aprieteel per'no de la Revise las medas de impulsi6n delanteras cada vez antes de segar, para asegurar_e de que se rnueven libremente. cuchilla gir#,ndolo en el sentido en que giran las rnanillas del reloj. - La torsi6n pare apretar recomendada es de 35 -40 pies libras. IMPORTANTE: EL PERNO DE LA CUCHILLA ES CLASE 8 TRATADO A CALOR Si las medas no giran libremente quiere decir qua hay basura, recortes de c_sped, etc. en el _rea de las ruedas de impulsi6n y tienen qua Iimpiarse pare liberaflaso AVISO: No recomendarnos el afilar la cuchilla pero si !o hace, asegdrese de que quede balanceada. Es necesario limpiar las ruedas de impu]siSn; revise arnbas ruedas delanteras. • Remueva los tapacubos, las clavijas de horquilla y las arandelas. - Remueva las ruedas de los ajustadores de tas ruedas.. ° Remueva la basura y los recortes de c_sped de dentro de la cubierta contra el polvo, piR6n y/o de los dientes de los engranajes de las ruedas de impulsidn. • Ponga las ruedas de vuelta en su lugar. • Si despu_s de lirnpiar las ruedas de impulsi6n no giran libremente, p6ngase en contacto con su centro de servicio rn&s cercano. RECOGEDOR DE ClaSPED PARA AFILAR LA CUCHILLA Se tiene que tener cuidado de manteneda balanceada. Una cuchilla que no est,. balanceada va a producir eventualmante da5o en fa segadora o en el motor° . La cuchilla puede afilarse con una lima o en una rueda rectificadora. No trate de afilada mientras se encuentm en la segadorao • Pare reviser el balance de la cuchilla, clave un clavo en una riga o en la pared. Deje alrededor de una pulgada de un clavo recto expuesto. Ponga el agujero central de la cuchiUa sobre la cabeza del clavo. Si la cuchilla est#. balanceada debe permanecer en ia posici6n horizontal. Si cualquiera de los extremos de la cuchilla se rnueve hacia abajo, afile el extremo pesado hasta que _sta quede batanceada. Adaptador de la cuchilla • El recogedor de c_sped puede ser rociado con et ague de la manguera pero tiene qua ester seco cuando se vaya a usar. ° Revise su recogedor de celsped a menudo pare vedficar si est_ dafado o deteriorado, Se vaa desgastar con el uso normal, Si se necesita cambiar el recogedor, c_tmbielo solarnente por uno que sea aprobado por el fabficante. D_ el nSrnero del modelo de la segadora cuando lo ordene. Chavetero del uenal Cuc_ Perno de la cuchi!la MOTOR LUBRICACION \',.,0 de la cuchilla de salida Arandela de seguddad Use solamente aceite de detergente de alta calidad clasificado con la clasificaci6n SF o SG de servicio API, Seleccione la calidad de viscosidad SAE segLin su temperature de opemci6n esperada. endurec_ CAUDADES DE VISOOS{DAD DE SAE CAJA DE ENGRANAJES o Pare mantener el sisterna de impulsi6n funcionando en forma adecuada, la caja de engmnajes y el _rea alrededor de la impulsi6n tienen qua rnantenerse lirnpias y sin acumulaciSn de basura. Limpie debajo de la cubierta de la impulsi6n dos veces por ternporada. ° La caja de engranajes se tlena con lubricante haste el nivet adecuado en la f_brica. La dnica vez que el lubricante necesita atenci6n es cuando sele ha prestado ser¢icio ala caja de engranajes. • Si se necesita lubricante, use solarnente Grasa Texaco Starplex Premium 1, Parte No. 750355. No use substitutos° ===== : _'F _¢..oo" -ZQ" .....-2'0". , , O' .... ................ _0" -1o" "===" , . , _'_* 40" 0" ,, I (;0' 110" ............. e(_' _0"..... .....t_ i ....... ;_" _, GAMA DE'£EMPERATURAAN_ICtPADA ANTES D,EL F_ r/xIp_O 04_B10 DE ACEITE AVISO: A pesar de qua los aceites de rnuftiviscosidad (5W30, t0W30, etc.) mejoran el arranque en clirna fifo, estos aceites de multMscosidad van a aumentar e! consurno de aceite cuando se usan en temperatures sobre 32 ° F. Revise el nivel deÁaceite del motor m_,s a menudo, pare evitar un posible dafio en el motor, debido a qua no tiene suficiente aceite_ Carnbie el aceite despu6s de las dos primeres horas de operaci6n y cada 25 horas de ahf en adelante, o por to menos una vez a! aRo, si la segadora no se usa 25 bores en un afio, 27 Revise el nivel del aceite del r_rter antes de arrancar el motory despuels de cada cinco (5) horas de uso continuado Apffete et _ap6n del aceite en forma segum cada vez que revise el nivel del aceiteo PARA CAMBIAR MOTOR EL ACEITE DEL AVISO: Antes de incliner la segadora pare drenar el aceite, drene el tanque de combustible haciendo correr el motor hasta que el tanque est_ vacioo - • - • • . • Acubierta del filtro de aire Desconecte et a|ambre de ia bujl'a y p6ngafo de mode que no pueda entrar en contacto con _sta Remueva ia tapa del depOsito del aceite; d6jeta a un lado en una superficie limpia Incline la segadora y h_gala descansar en su lado y drene el aceite en un envase adecuado Mueva la segadora de atr_s pare adelante pare remover todo el aceite que se haya quedado atrapado dentro del motor' Limpie todo el aceite derramado en la segadora yen el lado del motor L/ene el motor con aceite U_ne/o sotamente haste la Ifnea de "LLENO' (FULL) en la variIla indicadora de nivel NO LO LLENE DEMASIADO Vuelva a poner la tapa en el dep6sito del aceite. Vuelva a conectar el alambre de ia buj[a a _sta _Envase FILTRO DE AIRE Su motor no funcionar_ en forma adecuada y puede sufrir delos si se usa un filtro de aire sucio Cambie el filtro de aire cada a5o, y m_s a menudo si siege en condiciones mw polvorosas o sucias No lave el filtro de airg_ PARA CAMBIAR EL FtLTRO DE A1RE . Remueva el fiffro de aJregir_ndelo en el sentido contrario en que giran las manillas del reloj,haste el tope, y relirelo del coIlar_ • Remueva el filtro de la parte interior de la cubierte. • Umpie la parte interiorde la cubiertay el collar pare remover toda acumulaci6n de mugre • Inserte el filtro nuevo en la cubierta • Ponga la cubierta del filtro de aire dentro del coJJaraJineancb Jaore)a con la ranura • Empuje la cubierta hacia adentro y girela en el sentido de las manillas del reloj pare apreterla Bisagra Filtro de papel Tomillo de la cubierta SILENC/ADOR inspeccione y cambie el silenciador si est_ corroide pues j3mducirun pe/igro de incendio yio da_o BUJIA Cambie su bujfa cada a5o pare hacer que su motor arr-enque m_ f_cilmente y funcione mejor Ajuste la abertura de la bujra en O,030 pulgada LIMPIEZA IMPORTANTE: Para obtener el mejor rende-mento, mantenga la caja de la segador sin acumulation de cesped y basura. Umpie la parte de abajo de su segadera despues de cada uso, PRECAUOION: Desconecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta • Haga descansar la segadora en su lack) Aseg6rese que el t_ltrode aire y que el carburador queden mirando hacia aniba Limpie la parte inferior de su segadora rasp_indola pare remover la acumulaci6n de c_sped y basura • Umpie el motor a menudo pare evitar que se acumule la basura. Un motor tapado funciona m_.scatiente y se aoorta su duraci6n. ° Mantenga las superfides acabadas y las ruedas sin gasoline, aceite, etc. • No recomendamos el uso de una manguera de jardin pare limpiar la segadora a menos que et sistema el_ctrico, et silenciador, el filtro de aire y el calburador est_n tapaclos para evitar que les entre el agua. El ague en el motor puede acortar la duraci6n de _ste, LIMRE DEBAJO DE LA CUBIERTA DE LA IMPULSI6N Limpie debajo de la cubierte de la impulsi6n por 1o menos dos veces cada temporadao Raspe debajo de la cubief.a con un c_achillopara masitla o con una herramienta pare{ida, pare remover toda acumulaci6n de c_sped o basura en la parte inferior de la cubierta de la impulsi6n. 28 i i PRECAUCl 'N: Antes de dar calquier servicio o de hacer ajustes: . Suelte la barra de control y pare el motor. • Asegttrese que ]a cuchilla y que todas las partes movibles se hayan detenido completamente. o Desconecte el alambre de la bujfa y p6ngalo en donde no pueda entrar en contacto con _sta, SEGADORA PARA AJUSTAR CORTE LA ALTURA DE Vea "PARA AJUSTAR LA ALTURA DE CORTE" en la secoi6n de Operaci6n de este manual, DESVlADOR TRASERO Se proporciona un desviador trasero, adjunto entre las ruedas traseras de su segadora, pare reducir a un m[nimo la posibilidad que objetos seen lanzados haole afuera de la parte trasera de la segadora, an la posici6n en donde se encuentra el operador. Si se dafia el desviador debe cambiarse. PARA REMOVER/CAMBIAR DE IMPULSION LA CORREA • Remueva la cubierta de la impulsi6n. Remueva la correa empujando hacia abajo an la polea de la caja de engranajes, • Haga descansar la segadora an su lado con el filtro de aire y el carburador mirando hacia arrib& ° Remueva la cuchilla. ° Remueva la defense en contra de! desperdicio. ° Remueva la con'ea de la polea del motor en el ciguefiaL • lnstaJe la correa nueva siguiendo los pesos anteriores an el orden inverso. • Siempre use la correa aprobada por ia f_i.bfica pare asegurarse que calc_ y dure, PARA AJUSTAR EL MANGO Se puede levantar o bajar el mango de su segadora segSn le quede c6modo. Hay cuatro (4) posiciones disponibles: alta, mediana alta, mediana baja, baja. Los mangos se envfan montados en la posici6n mediana baja. • Pare cambiar de la posioi6n mediana baja a mediana alta, la secci6n superior y ta inferior del mango tendr_n que darse vuelta. . Remueva las abrazaderas del cable. ° Remueva los controles y la barra de control qua exige la presencia del operador del mango superior. ° Remueva las clavijas de horquilla. o Desconecte el mango inferior de los puntales del mango° - De vuelta el mango y vuelva a montar las clavijas de horquilla que se habfan removido, - Vuetva a montar los controles y la barra de controles qua exige la presencia del operador en el mango superior. PRECAUOION: La barra de control que exige la presencia del operador tiene que pivotear libremente pare permitir el enganche de la cuchilla/freno cuando se suelta la barra de control. No apriete demasiado los sujetadores que sujetan a los controles al mango superior. °Para cambiar de la posici6n de mediana baia a alta solamente se tendr& que dar vuelta la secci6n del mango superior,, • Pare cambiar de la posici6n mediana baja a baja, solamente se tendr_ que dar vuelta la secci6n del mango inferior. MOTOR CARBURADOR Su carburador tiene un chorro principal fijo no ajustable pare controtar la mezcla_ Si su motor no est& funcionando en forma adecuada debido a problemas que se sospecha vienen del carburador, Ileve su segadora a un centro de servicio autorizado pare repararia ylo ajustada VELOClDAD DEL MOTOR La velocidad del motor ha sido ajustada en la f_bricao No trate de aumentar la velocidad del motor pues se pueden producir lesiones personales_ Si cree que el motor est_ funcionando demasiado r_.pido o demasiado lento, lleve su segadora a un centro de servicio autorizado pare repararla o ajustarla. Cubierta de la impulsion Correa Empujar hacia abajo 29 Inmediatamente prepare su segadora para el almacenamiento al final de cada temporada o si la unidad no se va a usar por 30 dfas o m_s_ Barra de control que exige f SEGADORA Cuando se va a guardar la segadora por cierb perfodo de tiempo, limpiela cuidadosamente, remueva toda la mugre, la grasa, las hojas, etc. Gu_.rdela en un _.rea limpia y sec& • Limpie toda la segadora (Vea "LIMPIEZA" en la secci6n de Responsabitidades del Cliente de este manual). ° Lubrfquela segLin se muestra en la secci6n de Responsabilidades del Ciiente de este manual, • AseglJrese de que todas las tuercas y ctavijas y todos los pemos y tomillos est6n apretados en foma segura, lnspeccione las partes que se mueven para verificar si est_n da5adas, quebradas o desgastadas. C&mbielas si es necesario, ° Retoque todas las superficies que est_n ox:idadas o con la pintura picada; use una lija antes de pintar. MANGO Puede doblar el mango de su segadora para almacenarla_ • Apriete los extremos inferiores de! mango inferior entre si hasta que el mango inferior quede separado del puntal del mango, luego mu_valo hacia adelante. • Suelte los pemos de montaje del mango superior io suficiente como para permitir que el mango supedor se pueda doblar hacia atr_s, IMPORTANTE: Cuando done el mango para el anmacenamiento o el transporte, asegurese que lo doble segun se muestra o puede danar los cables de control. • Cuando prepare sus mangos a partir de la posici6n de almacenamiento, el mango inferior autom_,ticamente se asegurar_ en la posici6n para segan Mango inferior Puntal del Clavija de horquitla Doblar hacia atras Posici6n para segar MOTOR SlSTEMA DE COMBUSTIBLE IMPORTANTE: Es importante evitar que se formen depositos de goma en partes fundamentales del sistema de combustible tales como el carburador, el filtro del combustible, la manguera del combustible o en el estanque durante el almacenamiento,, La experincia tambien endica que los combustibles Mezcfados con alcohol (conocido como gasohol o que tienen etanol o metanol) pueden atraer humedad, Io queconduce a la separacion y a la forrnacion de acidos durante el almacenamiento° La gasolina acdica puede danar el sistema de combustible de un motor durante el periodo de almacenamiento. . Drene el estanque de combustible, ° Haga arrancar el motor y d6jelo funcionar hasta que las I[neas del combustible y el carburador est_n vacfos. ° Nunca use los productos para limpieza del carburador o del motor en el estanque de combustible pues se pueden producir daRos permanentes. • Use combustible nuevo la pr6xima temporada. AVlSO: El estabilizador de combustible es una altemativa aceptable para reducir a un mfnimo la formaci6n de dep6sitos de goma en el combustible durante el pedodo de almacenamiento. Agregue estabilizador a la gasolina en el estanque de combustible o en et envase para el almacenamiento, Siempre siga la proporci6n de mezcla que se encuentra en el envase det estabilizador. Haga funcionar el motor porlo menos 10 minutos despu6s de agregar el estabilizador, para permitir que este Ilegue al carburador. No drene la gasolina del estanque de gasolina y el carburador si se est,, usando estabilizador de combustible. ACEITE DEL MOTOR Drene el aceite (con el motor caliente) y c_,mbielo con aceite de motor limpio,, (Vea "MOTOR" en la secci6n de Responsabitidades del Ctiente de este manual,) 30 CtLINDRO , Remueva la buj{a_ - Vac[e una onza (29 ml) de aceite a tray,s del agujero de la buj[a en el ci[indro. • Tire la manilla de arrangue lentamente unas cuantas veces para distribuir el aceite. • Vuelva a montar la nueva bujfa. OTROS ° No guarde la gasolina de una temporada a la otra. , Cambie et envase de la gasolina si se empieza a oxidar. La oxidaci6n yio la mugre en su gasolina producir&n problemas. • Si es posible, guarde su unidad en un recinto cerrado y cdbrala para protegeda contra et pofvo y la mugre. IDENTIFICAClON PRECAUOION: Nunca almacene la segadora con gasolina en et estanque dentro de un edificio en donde los gases pueden alcanzar una llama expuesta o una chispa. Permita qua se enfr[e el motor antes de almacenarla en algdn recinto cerrado. DE PROBLEMAS PROBLEMA CORRECClON CAUSA ..... No arranca o Cubra su unidad con un forro protector adecuado qua no retenga la humedad No use pl_stico. El pl#.stico no puede respirar, Io qua perrnite la formaci6n de condensaciSn, Io qua producir,_ la oxidaci6n de su unidad_ IMPORTANTE: Nunca cubra la segadora nientras et motor y las areas de escape todav{a estan calientes - i iilul J illl Limpie/cambie el filtro de aire. • Filtro de aire sucio_ • Sin combustible o Liana e! estanque de combustible • Combustible rancio. o Drene el estanque y vuelva a llenarlo con combustible limpio y nuevo • Agua en el combustible. ° Drene el estanque de combustible y el carburador y vuelva a Ilenar el estanque con gasolina nueva. o Alambre de la buj[a desconectado. • Conecte el alambre a _abuj[a ° Bujfa mala. • Apdete el pemo de la cuchi!la o cambie el adaptador de la cuchitlao • Presione la barra de control hacia el mango. ° Cambie la barra de control_ • Cambie la bujfa. o Cuchilla suelta o adaptador de la cuchilla quebrado. ° Barra de control en ta posici6n suelta. Falta de fuerza • Barra de control defectuosa. Ajuste a la posici6n de "Corte mrs a_to." •Parte trasera de la cajacuchilla de la segadora arrastr_ndose en el c_sped pesado. Ajuste a la posici6n de "CoRe m_s alto." • Est,. cortando mucho c6sped. • Filtro de aire sucio. • Limpie/cambie • Acumulaci6n de c_sped, hojas y basura debajo de la segador& • Revise et nivel del aceite. • Demasiado aceite en el motor. 31 el filtro de aire_ • Limpie la parte inferior de la caja de la segadora. • Corte a una velocidad de recorfido m&s lenta PROBLEMA Vial corte -disparejo Vibraci6n excesiva Cord6n arrancador diffcil de tirar Recogedor de c6sped no se llena (si viene equipado) Diffcil de empujar ...... CORRECCION CAUSA Cuchilla desgastada, doblada o • Cambie fa cuchillaoApdete el suelta pemo de la cuchillao o Ajuste todas las ruedas a la • Altura de las ruedas dispareja misma altura - Vetocidad del motor lenta ° P6ngase en contacto con su centro de servicio autorizado m_s cercano • Limpie la parte inferior de la caja . Acumulaci6n de c_sped, hojas o basura debajo de la segadora de fa segadora • Cuchilla desgastada, doblada o suelta . CigueSal del motor dobtadoo • Cambie la cuchillaoApriete el pemo de la cuchilla, ° P6ngase en contacto con su centro de servicio autorizado m&s cercano. • El freno del volante del motor est_ aplicado cuando se suelta ia barra de control ° Ciguefial del motor doblado • Adaptador de la cuchilla quebrado ° La cuchilla se arrastra an el c_spedo • Presione la barra de control hacia el mango superior antes de tirar el cord6n arrancador • P6ngase en contacto con su centro de servicio autorizado m,_s cercano. • Cambie el adaptador de la cuchilla. • Mueva la segadora a un lugar en donde el c_sped ha sido cortado o a una superficie firme pare hacer arrancar el motor . • Eleve la altura de torte • Cambie la cuchillas • Limpie e[ recogedor de c_sped ° Ajuste el control de la velocidad del motor a la posici6n r_pida Altura de corte demasiado baja. Levantamiento de la cuchilla desgastado. ° Recogedor sin ventilaci6n de aire, ° Velocidad del motor lenta. - El c_sped est_ demasiado alto o la altura de la rueda demasiado baja Parte trasera de la caja/cuchilta de la segadora arrastr_ndose en el c_spedo Recogedor de c6sped demasiado Iteno. Posici6n de la altura del mango no adecuada para usted. 32 Eleve la altura de corte, Eleve la parte trasera de la caja de ta segadora (i) un lugar m&s alto Vacfe el recogedor de c_spedo Ajuste la altura det mango de modo que le acomode -r ROTARY LAWN MOWER -- MODEL NO. 917.379300 GEAR CASE ASSEMBLY PART NUMBER 702511 KEY NOo PART NO. 17490416 2 3 4 6 7 8 9 10 137055X004 137053 57072 48373 77881 137051 137074 57079 DESCRIPTION KEY NO. Tapping Screw 1/4-20 x 1-1/4 Engagement Bracket Shifter Seal Gear Case Halves Kit (Includes Key Noso 4, 5, and 7) Bearing Worm Shalt Drive Shatt Hardened Washer 1t 12 I3 14 15 16 t7 18 19 PART NO. 131484 700343 86447 137050 750436X 750369 12000003 850848 81585X004 DESCRIPTION Clutch Yoke Bushing Plug Helical Gear Clutch Jaw Grease E-Ring Hi-Pro Key Spring Bracket NOTE: All component dimensions given in U.S, inches° 1 inch = 25A mm 33 CRAFTSMAN ROTARY LAWN MOWER-- MODEL NO. 917.379300 12 f..,o _15 16 lZ 2O 35 F12 66 j L_ CRAFTSMAN ROTARY LAWN MOWER -- MODEL NO. 917.379300 KEY NO. O3 O3 1 2 4 5 6 8 9 t0 1t 12 13 14 15 16 17 18 20 22 23 25 27 28 29 30 31 32 34 35 37 PART NO. 145646)(479 158152 150425 151517 136376 145793 151023 128415 150050 STD512505 150181 700483X479 700365X479 133190)(479 140661X479 STD541425 14O540 85543 87677 83923 150341 142748 62335 145935X004 701037 700331X004 146630 700325X007 150078 DESCRIPTION Upper Handle Engine Zone Control Cabte Mulcher Plug Cable Clip Handle Knob Control Bar Rear Door KIt Pop Rivet Self Tapping Screw #10-16 x 1/2 Hex Tapping Screw wtSems 1/4-20 x 1/2 Hubcap Back Plate Side Baltle DischargeBaffle Rear Battle Keps Locknut 1/4-20 Rear Skirt Engine Pulley Hi-Pro Key #505 Hex Flange Nut Wheel Shoulder Bolt 3/8-16 x 1 Spring Washer Axle Arm Assembly Selector Knob SeIector Spring Spacer Wheel Adjusting Bracket (Right) Thread Cutting Screw w/Seres 5/t6-18 x 3/4 KEY NO. PART NO. 38 39 40 4t 44 751592 15t512X479 15t511X479 150406 48413 46 47 48 49 50 51 52 56 57 58 59 61 62 64 - - 851514 1571O1 851074 850263 851084 700869X479 85463 88652 51793 157081)(479 131959 132001 134612 DESCRIPTION Nut Handle Bracket Assembly (Lett) Handle Bracket Assembly (Right) Hex HeadThread Rolling Screw 3/8-16 x 1-1/8 Lawn Mower Housing (lncL Key #t4, 15, 51 & 52) 159290 Blade Adapter Blade 22" Hardened Washer Helical Washer 3/8-24 x 1-3/8 Gr. 8 Hex Head Machine Screw 318-24 x 1-3/8 Gr. 8 Front BaItle Danger Decal Hinge Screw 1/4-20 x t-1/4 Hairpin Cotter Lower Handle Handle Bolt Rope Guide Debris Shield Engine-Craftsman - Model No. 143.976608 Owner's Manual (English/Spanish) Available accessories not includedwith lawn mower: - 71 33303 Ctipping Deflector -71 33623 Gas Can (2.5 gal.) - _ 33500 Fuel Stabilizer - 71 33027 SAE 30W Oil (27 oz.) -7"133417 Dust Shield -71 33316 Mower Cover CRAFTSMAN ROTARY LAWN MOWER - - MODEL NO. 917.379300 13 co 14 CRAFTSMAN KEY NO. 03 ",4 1 2 3 4 5 6 8 9 10 11 12 13 !4 15 16 18 PART NO. 145755 48385 68038 144929 146527 150495 150182 145212 88446 150340 12000058 137054 88080 88118 67725 701037 ROTARY LAWN MOWER - - MODEL NO. 917.379300 DESCRIPTION Control Cable Assembly Control Head Kit Locknut #10-24 Hex Washer Head Screw 1/4-20 x 2.t2 V-Belt Spring Retainer Hubcap Locknut Nylon Bushing Wheel & Tire Assembly E-Ring Plnton Dust Cover Felt Washer Washer 1/2x 1-1/2 x .t34 Selector Knob KEY NO. 25 26 28 31 32 33 35 36 37 38 40 41 53 54 55 57 PART NO. 152903 143603 154990 132010 137052 48386 151521 702511 137090 STD541425 75192 151520 144747 154870 86012 144748 DESCRIPTION Drive Cover Decal Pan Head Tapping Screw #10-24 x 2-3/4 Drive Cover Hex Flange Nut Drive Pulley Drive Control Cable Kit Wheel Adjuster Assembly (Left) Gear Case Assembly Spring Locknut t/4-20 Spring Wheel Adiuster Assembly (Rlgrlt) Frame Throat Grassbag Assembly Driveshatt Cover Frame Tube CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.976608 1BTA \ 38 KEY NO. PART NOo 36177 2 6 7 9 10 11 12 t4 t5 16 17 18 19 2O 25 27652 36059 36005A 590568 36002 36003 32447 28277 36006 36008 3t 335 651018 361O3 36010 36186 26 30 40 4o 41 650802 36185 40004 40005 36070 41 36071 42 42 43 45 40006 40007 20381 36023A 46 48 50 52 69 7O 32610A 36030 36031A 29914 36032A 36194 72 73 75 8o 81 82 83 85 86 89 90 91 92 93 1co !01 103 30572 28833 36010 30574A 30590A 30591 36057 36034 650924 611154 611155 611156 650815 650816 34443A 610118 65t 007 110 1'19 120 125 125 126 126 130 135 150 !51 151A 169 172 174 36054 36061 36187 36471 36472 29314B 293150 6021A 35395 31672 31673 40016 27234A 32755 30200 DESCRIPTION KEY NO. PART NO. DESCRIPTION Cylinder (IncL 2,t0,12,20 & 177 650925A Carburetor Mounting Stud CaYouretor Gasket 125) 184 36183 Dowel Pin 186 36009 Governor Unk Air Batlle Breather Element 187A 36195 * Breather Cover & Gasket 190 36013 Brake Lever Ass'y,. Brake Control Lever Screw, !0-24 x 3/4" 191A 36012 Brake Control Lever Unk Breather VanceBody 192 36016 Check:Valve 193 36015 Brake Spring Breather Tube 194 36014 Retaining Ring Fiat Washer 195 610973 Terminal Ass'yo Govemor Rod (Machined) 198 36017 Brake Control Lever Spring Governor Lever 199 36018 Brake Lever Bushing Governor Lever Clan_ 202 36482 Compression Spring Screw, Torx T-15, 8-32x 19/64" 203 31342 Compression Spring Screw, 5-40 x 7/16" Governor Spring 204 65! 029 O]I Seal 205 651030 Screw, Torx 1"-10, 6-32 x 17/32" Control Knob Blower Housing Batl_ Ass'y. 215 36051 Carburetor To Air Clearer (Inc[195) 239 36048 Gasket Screw, 1/4-20 x 5/8" Crankshatt 240 36190 Air Cleaner Body (Incl,239 & Piston,Pin,Ring Set (Std.) 350) Air Cleaner Stud Piston,Pin,Ring Set (.010 OS) 243B 651041 Air Cleaner Filter Piston & Pin Ass'y_(Std.) (incL 245 36046 Air Cleaner Cover 43) 25O 36191 Lock Nut 1/4-20 Piston & Pin Ass'yo 251 650928 (.010 OS)(Ir_r.JAS) 25IA 650933 Wing Nut, 1t4-20 Control Plate Ring Set (Stdo) 255 36193 Ring Set (_010OS) 256 650983 Screw, 8-32 x 21/64" Piston Pin Retaining Ring 260 36188 Blower Housing Connecting Rod Ass'y,, (IncL 261 650737 Screw, 1/4-20 x 1/2" Screw, 1/4-20 x 11/16" 46) 262 650929 Starter Grill Connecting Rod Bolt 263A 36192 Valve Lifter 275 36107 Muffler Camshaft (MCR) 276 36043 Locking Plate Oil Purr# Ass'y_ 277 650927 Screw, 5/6-18 x 2-11/32" * Mounting Range Gasket 285 34449A Statler Cup Mounting Range (IncL 72 thru 287 650926 Screw, 8-32 x 21/64" Fuel Une 85) 290 29774 Oil Drain Plug (IncL 73) 292 26460 Fuel Une Clamp Drain Plug Gasket 300 36189 Fuel Tank (Incl, 301) O11Sea] 301 36246 Fuel Cap Governor Shaft 305 36063 Oit FillTube Washer 307 35499 "O" Ring Governor Gear Ass'y. (Incl,81) 308 36040 Fill Tube Clip Governor Spool 310 36064 Dipstick Idler Gear 346A 28763 Screw, 10-32 x 35/64" Screw, 1/4-20 x 1-9/16" 347 650898A Screw, 10-32 x 27/32" Pdmer Flywheel Key 350 36045 Flywheel 370A 36261 Lubrication Decal Conlrol Decal Flywheel Fan 370B 36155 BelleviUeWasher 370C 36861 Primer Decal Flywheel Nut 380 640020 Carburetor (incl, 164,239) Solid State Ignition 390 590702 Rewind Starter Gasket Set Spark Plug Cover 400 36062C Screw, Torx T-15, t0-24 x 15/ (Incl. Items Marked * tn Notes) 16" 416 36085 Spark Arrestor Kit Ground Wire (incl. 417)(Optione]) * Cylinder Head Gasket 417 650760 Screw, 8-32 x 3/8" (q3tional) Cylinder Head 900 Replacement Engine 750792B, onJer from 71-999 Exhaust Valve (Std.) (inc[. 151) Exhaust VaJve(1/32" OS) 900 Replacement S/B 750797, order from 71-999 Intake Valve (Std.) (lnd_ 151) Intake Valve (1/32" OS) RPM High 2900 to 3200 RPM Low 2450 to 2750 Screw, 5116-18x 1-1t2" --Resistor Spark Plug (RJ19LM) (NOTE: This engine could have been built with 590739 Valve Spring starter. Reler to the design o! the rope pulley strength Lower Valve Spring Cap rbs for part identilication. Intake Valve Sea/ NOTE*. All corr#onent dimensions given in U_Soinches t Inch = 25.4 mm * Valve spring Box Gasket Valve Spring Box Cover Screw, 10-24 x 9/16" 39 MODEL NUMBER 143.9766,08 ...... I KEY NO,, PART NO, DESCRIPTION 640020 Carburetor (lncL 187B & 239 of Engine Parts List) Throttle Shaft & Lever Assembly Dust Seal Throttle Shutter Throttle Shutter Screw Float Bow] Idle Restdctor Float Shaft Float Float Bowl to Body Gasket Inlet Needle & Seat Bowl Drain Screw Bowl Drain Washer Main Nozzle Tube "0" Ring "O" Ring, Main Nozzle Tube Spring, Main Nozzle Tube Spring Float Bowl Retainer Main Fuel Jet Welch Plug, Idle Mixing Well 632539 5 6 7 25 25A 27 28 29 632593 63254 t 650506 632675A 632701 632544 632543 632548 30 32 33 36 37 37A 632709 632672 632673 640022 632547 632547 38 632545 38A 3g 40 47 632545 632549 640021 632554 40 - CRAFTSMAN 4-CYCLE ENGINE MODEL NUMBER 143.976608 KEY NO,, PART NO, 11 590703 12 590535 13 590701 Recoil Starter Spring Pin (IncL 4) Washer Retainer Washer Brake Spdng Starter Dog Dog Spring Pulley & Rewind Spring Ass'y. Starter Housing Ass'y, (40 degree grommet) Statler Rope ( 98" X 9/ 64" dial,) Starter Handle PART NQ DESCRIPTION 1 2 3 4 5 6 7 8 590702 590599A 590600 590696 590601 590697 590698 590699 590700 DESCRIPTION O_2 KEY NQ 3 6 7 8 41 590739 590740 590616 590617 590618A 11 590638 t2 590535 13 14 590701 590741 Rewind Starter Retainer Starter Dog Dog Spring Pulley & Rewind Spring Ass'y Starter Housing Ass'y (40 degree grommet) Starter Rope (Lenglh 98" x 9/64" dia,,) S_arter Handle Locking Tab 42 43 For the repair or replacement parts you need delivered directly to your home Call 7 am - 7 pm, 7 days a week 1=800-366=PART (1-800-366-7278) Para ordenar piezas con entrega a domicilio - 1-800-659-7084 For in-house major brand repair service Call 24 hours a day, 7 days a week 1-800-4..REPAIR (1-800-473-7274) Para pedir servicio de reparaci6n domicilio - 1-800-676-5811 a For the location of a Sears Parts and Repair Center in your area Call 24 hours a day, 7 days a week 1-800-488-1222 For information on purchasing a Sears Maintenance Agreement or to inquire about an existing Agreement Call 9 am - 5 pm, Monday-Saturday 1-800..827-6655 When requesting service or ordering parts, always provide the following information: • Product Type ,, Part Number • Model Number o Part Description Amenca s Repair Specialmts 159290 10,20.97 REV,2 VB Printed in U,S.A.
This document in other languages
- español: Craftsman 917.379300